Recently, the demand for electric vehicle is increasing worldwide due to eco-friendly policies and stricter emission regulations. As a traction motor for electric vehicle, interior permanent magnet synchronous motors are mainly used. For the design of the interior permanent magnet synchronous motor, the magnetic equivalent circuit method, which is a method of lumped constant circuit, and the finite element method, which is a method of distributed constant circuit, mainly are used. Magnetic equivalent circuit method is useful for simple design through fast and intuitive parameters, but it cannot derive the distribution of magnetic field. The finite element method can derive an accurate magnetic field distribution, but it takes a long time to analyze and it is difficult to analyze intuitive design parameters. In this paper, magnetic equivalent circuit method and Carter coefficient are mixed for rotor structure design. This design method will be called the hybrid magnetic equivalent circuit method. Intuitive design parameters are derived through this hybrid magnetic equivalent circuit method. We will derive the Air gap flux density distribution according to rotor shape, no-load induced voltage, and cogging torque, and compare and verify it with the finite element method.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.

Cellular redox state is highly dynamic and delicately balanced between constant production of reactive oxygen species (ROS), and neutralization by endogenous antioxidants, such as glutathione. Physiologic ROS levels can function as signal transduction messengers, while high levels of ROS can react with and damage various molecules eliciting cellular toxicity. The redox state is reflective of the cell’s metabolic status and can inform on regulated cell-state transitions or various pathologies including aging and cancer. Therefore, methods that enable reliable, quantitative readout of the cellular redox state are imperative for scientists from multiple fields. Liquid-chromatography mass-spectrometry (LC-MS) based methods to detect small molecules that reflect the redox balance in the cell such as glutathione, NADH and NADPH, have been developed and applied successfully, but because redox metabolites are very labile, these methods are not easily standardized or consolidated. Here we report a robust LC-MS method for the simultaneous detection of several redox-reactive metabolites that is compatible with parallel global metabolic profiling in mammalian cells. We performed a comprehensive comparison between three commercial hydrophilic interaction chromatography (HILIC) columns, and we describe the application of our method in mammalian cells and tissues. The presented method is easily applicable and will enable the study of ROS function and oxidative stress in mammalian cells by researchers from various fields.

Legacy mining industry has left a large number of tailings ponds exposed to water and wind erosion that causes serious environmental and health problems. Prior to rehabilitation actions a deep sampling of the materials infilling the pond used to be necessary. Thus, the primary objective of this study is to demonstrate the usefulness of the Electrical Resistivity Tomography (ERT) method as a non-invasive tool to determine the physicochemical composition of mine tailings ponds, enabling more efficient and low-cost surveys. To achieve this objective, three ERT profiles and three boreholes in each profile were carried out, from each borehole three waste samples from differents depths were collected and a geochemical characterization of the samples was carried. In order to estimate the composition of the infilling wastes in tailing ponds from electrical resistivity measures, several regression models were calculated for different physicochemical properties and metal concentrations. As a result, a high resistivity area was depicted in profiles G2 and G3 while a non-resistive area (profile G1) was also found. Relationships among low resistivity values and high salinity, clay content and high metal concentrations and mobility were established. Specifically, calibrated models were obtained for electrical conductivity, particles sizes of 0.02-50 µm and 50-2000 µm, total Zn and Cd concentration, and bioavailable Ni, Cd and Fe. Therefore, the ERT technique could be considered as a useful tool for mine tailings ponds characterization, and it can be used to estmate some physicochemical properties and metal concentrations of this mine waste.

Satellite-based remote sensing technologies are utilized extensively to investigate urban thermal environments under rapid urban expansion. Current MODIS data is, however, unable to adequately represent the spatially detailed information because of its relatively coarser spatial resolution, while Landsat data can’t explore temporally the refined analysis due to the low temporal resolution. In order to resolve this situation, we used MODIS and Landsat data to generate “Landsat-like” data by using the flexible spatiotemporal data fusion method (FSDAF), and then studied spatiotemporal variation of land surface temperature (LST) and its driving factors. The results showed that 1) The estimated “Landsat-like” data have high precision; 2) By comparing 2013 and 2016 datasets, LST increases ranging from 1.8°C to 4°C were measurable in areas where the impervious surface area (ISA) increased, while LST decreases ranging from -3.52°C to -0.70°C were detected in areas where ISA decreased; 3) LST has a strongly negative relationship with the Normalized Difference Vegetation Index (NDVI), and a strongly positive relationship with Normalized Difference Built Index (NDBI) in summer; and 4) LST is well correlated with Building density (BD), in a complex conic mode, and LST may increase by 0.460°C to 0.786°C when BD increases by 0.1. Our findings can provide information useful for mitigating undesirable thermal conditions and for long-term urban thermal environmental management.

The NCO functional group of 3-isocyanatoproply triethoxysilane (IPTS) and the OH functional group of DOPO-BQ were used to conduct an addition reaction. Following completion of the reaction, triglycidyl isocyanurate (TGIC) was introduced to conduct a ring-opening reaction. Subsequently, a sol-gel method was used to take place a hydrolysis- condensation reaction on TGIC-IPTS-DOPO-BQ to form a hyperbranched nitrogen–phosphorous–silicon (HBNPSi) flame retardant. This flame retardant was incorporated into a polyurethane (PU) matrix to prepare a hybrid material. Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), limiting oxygen index (LOI), UV-VIS spectrophotometry, and Raman analysis were conducted to structure characterization and analyzed transparency, thermal stability, flame retardancy, and residual char to understand the flame retardant mechanism of prepared hybrid materials. After the flame retardant was added, the maximum degradation rate decreased from −36 wt%/min to −17 wt%/min, the integral procedure decomposition temperature (IPDT) increased from 348 ℃ to 488 ℃, and the char yield increased from 0.7 to 8.1 wt%. The aforementioned results verified that thermal stability of PU can be improved after adding HBNPSi. The LOI analysis indicated that the pristine PU was flammable because the LOI of pristine PU was only 19. When the content of added HBNPSi was 40%, the LOI value was 26; thus the PU hybrid became nonflammable.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

Capabilities of the Attenuated Total Reflection (ATR) at THz wavelengths for increased sub-surface depth characterisation of (bio-)materials is presented. The penetration depth of a THz evanescent wave in biological samples is dependent on the wavelength and temperature and can reach 0.1-0.5 mm depth due to strong refractive index change ∼0.4 of the ice-water transition; this is quite significant and important when studying biological samples. Technical challenges are discussed when using ATR for uneven, heterogeneous, high refractive index samples with possibility of frustrated total internal reflection (a breakdown of the ATR reflection-mode into transmission-mode). Local field enhancements at the interface are discussed with numerical/analytical examples. Maxwell’s scaling was used to model behaviour of absorber-scatterer inside materials at the interface with ATR prism for realistic complex refractive indices of bio-materials. Modality of ATR with polarisation analysis is proposed and its principle illustrated, opening an invitation for its experimental validation. The sensitivity of the polarised ATR mode to the refractive index between the sample and ATR prism is revealed. Design principles of polarisation active optical elements and spectral filters are outlined. The results and concepts are based on experiments carried out at the THz beamline of the Australian Synchrotron.

In this effort we propose a data-driven learning framework for reduced order modeling of fluid dynamics. Designing accurate and efficient reduced order models for nonlinear fluid dynamic problems is challenging for many practical engineering applications. Classical projection-based model reduction methods generate reduced systems by projecting full-order differential operators into low-dimensional subspaces. However, these techniques usually lead to severe instabilities in the presence of highly nonlinear dynamics, which dramatically deteriorates the accuracy of the reduced-order models. In contrast, our new framework exploits linear multistep networks, based on implicit Adams-Moulton schemes, to construct the reduced system. The advantage is that the method optimally approximates the full order model in the low-dimensional space with a given supervised learning task. Moreover, our approach is non-intrusive, such that it can be applied to other complex nonlinear dynamical systems with sophisticated legacy codes. We demonstrate the performance of our method through the numerical simulation of a two-dimensional flow past a circular cylinder with Reynolds number Re = 100. The results reveal that the new data-driven model is significantly more accurate than standard projection-based approaches

Using the above results from RMS analysis the optimum values were predicted for the independent significant variables (Figure 3) the optimized levels of these variables in combination with other media variables the maximum production was predicted to be 199.90 U/mL. The predicted data were validated through confirmatory experiments performed in triplicates. A 1.29-fold increase in amylase activity against un-optimized (OVAT) medium was achieved in the present study authenticating the efficacy of RSM in process optimization (Figure 4). 2.6 Model validation and scale-up at laboratory scale (5L) bioreactor Once the parameters were standardized in the shake-flasks culture, the experiment was scaled-up to a laboratory-scale bioreactor (5 L). The yield of amylase increased by 1.01 fold (205.69 U/mL), it could be possible because the enzyme production in a bioreactor is higher than in shake-flasks culture as the various critical variable factors such as the dissolved oxygen (DO) and the pH can be optimally controlled at the desired levels [22].

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

Background: Identification of cancer biomarkers that are differentially expressed (DE) under two biological conditions is an important task in many microarray studies. There exist several methods in the literature in this regards and most of these methods designed especially for unpaired samples, which does not satisfy the requirements of paired samples where the gene expressions are taken from the same patients before and after treatment. Furthermore, the traditional biomarker identification methods based on either p-values or fold change (FC) values. However, sometimes, p-value based results do not comply with FC based results due to the smaller variance of gene expressions. There are some methods that combine both p-values and FC values to solve this problem. But, these methods also show weak performance for small-sample case in presence of outlying expressions. To overcome this problem, in this paper an attempt is made to develop a hybrid robust SAM-FC approach by combining rank of FC values and rank of p-values based on SAM statistic using minimum β-divergence method, which is designed for paired samples. This method introduces a weight function known as β-weight function. This weight function produces larger weights corresponding to usual/normal expressions and smaller weights for unusual/outlying expressions. The β-weight function plays the significant role on the performance of the proposed method. Results: The proposed method uses β-weight function as a measure of outlier detection by setting β=0.2. We unify both classical and robust estimates using β-weight function such that maximum likelihood estimators (MLEs) are used in absence of outliers and minimum β-divergence estimators are used in presence of outliers to obtain reasonable p-values and FC values in the proposed method. We examined the performance of proposed method in a comparison of some popular methods (t-test, SAM, LIMMA, Wilcoxon, WAD, RP and FCROS) using both simulated and real gene expression profiles for both small-and large-sample cases. From the simulation and a real spike in data analysis results we observed that the proposed method outperforms other methods for small-sample case in presence of outliers and it keeps almost equal performance with other robust methods (Wilcoxon, RP and FCROS) otherwise. From a head-and-neck cancer (HNC) dataset the proposed method identified 2 genes (CYP3A4, NOVA1) that are significantly enriched in linoleic acid metabolism, drug metabolism, steroid hormone biosynthesis and metabolic pathways. The survival analysis through Kaplan-Meier curve revealed that combined effect of these 2 genes has prognostic capability and they might be promising biomarker of HNC. Moreover, we retrieved the 12 candidate drugs based on gene interaction from glad4u and drug bank databases. Conclusion The identified drugs showed statistical significance and critical role of the proteins indicate that these proteins might be therapeutic target in cancer. Thus, elucidating the associations between the drugs identified in the present study require further investigations.

Recent advance in electric propulsion systems have demonstrated that these engines can be used for for long-duration interplanetary voyages. Constant specific impulse engine described as a thrust-limited engine is an example of this type of engine, processing the ability to operate at a constant level of impulse. The determination of minimum-fuel, planar heliocentric Earth-to-Mars low-thrust trajectories of spacecraft using a constant specific impulse is discussed considering the first-order necessary conditions derived from Lawden’s primer vector theory. The minimum-fuel low-thrust Earth-to-Mars optimization problem is then solved in two-dimensional, heliocentric frame using both indirect and direct methods. In the indirect method, two-point-boundary-value problems are derived to solve boundary value problems for ordinary differential equations. In the direct method, a general-purpose optimal control software called GPOPS-II is adopted to solve these optimal control problems. Numerical examples using two different optimization methods are presented to demonstrate the characteristics of minimum-fuel planar low-thrust trajectories with on-off-on thrust sequences at three chosen flight times and available maximum powers. The results are useful for broad trajectory search in the preliminary phase of mission designs.

The information entropy for Smoluchowski coagulation equation is proposed based on statistical mechanics. And the normalized particle size distribution is a lognormal function at equilibrium from the principle of maximum entropy and moment constraint. The geometric mean volume and standard deviation in the distribution function are determined as simple constant. The results reveal that the assumption that algebraic mean volume be unit in self-preserving hypothesis is reasonable in some sense. Based on the present definition of information entropy, the Cercignani’s conjecture holds naturally for Smoluchowski coagulation equation. Together with the proof that the conjecture is also true for Boltzmann equation, Cercignani’s conjecture will holds for any two-body collision systems, which will benefit the understanding of Brownian motion and molecule kinematic theory, such as the stability of the dissipative system, and the mathematical theory of convergence to thermodynamic equilibrium.

Biodiesel has caught the attention of many researchers because it has great potential to be sustainable fossil fuel substitute. Biodiesel has non-toxic and renewable nature and has been proven to emit less amount of environmentally harmful emissions such as hydrocarbons (HC), and carbon monoxide (CO), as well as smoke particles during combustion. Problems related to global warming caused by greenhouse gas (GHG) emissions could also be solved by utilizing biodiesel as a daily energy source. However, the expensive cost of biodiesel production, mainly because of the cost of natural feedstock, holds the potential of biodiesel commercialization. The selection of natural sources of biodiesel should be made with observations from economic, agricultural, and technical perspectives to obtain one feasible biodiesel with superior characteristics. This review paper presents a detailed overview of various natural sources, their physicochemical properties, as well as the performance, emission, and combustion characteristics of biodiesel when used in a diesel engine. The recent progress in studies about natural feedstocks and manufacturing methods used in biodiesel production were evaluated in detail. Finally, the findings of the present work reveal that transesterification is currently the most superior and commonly used biodiesel production method compared to other methods available.

Nowadays, according to spectacular improvement in health care and biomedical level, a tremendous amount of data is recorded by hospitals. In addition, the most effective approach to reduce disease mortality is to diagnose it as soon as possible. As a result, data mining by applying machine learning in the field of diseases provides good opportunities to examine the hidden patterns of this collection. An exact forecast of the mortality after heart surgery will cause Successful medical treatment and fewer costs. This research wants to recommend a new stacking predictive model after utilizing the random forest feature importance method to foresee the mortality after heart surgery on a highly unbalanced dataset by using the most practical features. To solve the unbalanced data problem, a combination of the SVM-SMOTE over-sampling algorithm and the Edited-Nearest-Neighbor under-sampling algorithm is used. This research compares the introduced model with some other machine learning classifiers to ensure efficiency through shuffle hold-out and 10-fold cross-validation strategies. In order to validate the performance of the implemented machine learning methods in this research, both shuffle hold-out, and 10-fold cross-validation results indicated that our model had the highest efficiency compared to the other models. Furthermore, the Friedman statistical test is applied to survey the differences between models. The result demonstrates that the introduced stacking model reached the most accurate predicting performance after Logistic Regression.

This study focused on hydrolysis of cosmetic fillers hyaluronic acid (HA) and kinetics of the HA hydrolysis using the homogenate of the red king crab hepatopancreas. Turbidimetric analysis of the reaction mixture revealed a bell-shaped time dependence of aggregation formation. It was shown that the obtained homogenate has the similar activity to the commercially available hyaluronidase. The atomic force microscopy (AFM) examination found that the HA fillers were represented by spherical-like structures. These structures were destroyed under the action of the homogenate of the red king crab hepatopancreas. NMR of the reaction mixture showed that HA degradation lasts for some days, but a maximum rate of the reaction is detected in the first hours of incubation. The preparation with hyaluronidase activity obtained from the red king crab hepatopancreas could be used as potentially safe product for treating filler complications.

Detection of early stage corrosion on slender steel members is crucial for preventing buckling failures of steel structures. An active photoacoustic fiber optic sensors (FOS) system has been reported for early stage steel corrosion detection of steel plates and rebars using surface ultrasonic waves. The objective of this paper is to investigate the surface corrosion/rust detection problem on steel rods using numerically simulated surface ultrasonic waves. The finite element method (FEM) is applied in simulating the propagation of ultrasonic waves on steel rod models. Transmission mode of damage detection is adopted, in which one source (transmitter) and one sensor (receiver) are considered. In this research, radial displacements at the receiver were simulated and analyzed by short-time Fourier transform (STFT) for detecting, locating, and quantifying a surface rust located between the transmitter and the receiver. From our time domain and frequency domain analyses, it is found that the presence, location, and dimensions (length, width, and depth) of surface rust can be estimated by ultrasonic waves propagating through the surface rust.

This article discusses the results of a series of experiments on pulse ultrasonic cure monitoring of carbon fiber reinforced plastics applied to the pultrusion process. The aim of this study is to validate the hypothesis that pulse ultrasonic cure monitoring can be applied a) for profiles having small cross sections such as 7x0.5 mm and b) within the environment of the pultrusion process. Ultrasonic transducers are adhesively bonded to the pultrusion tool as actuators and sensors. The time-of-flight and the amplitude of an ultrasonic wave are analyzed to deduce the current curing state of the epoxy matrix. The experimental results show that ultrasonic cure monitoring is indeed applicable even to very thin cross sections. However, significant challenges can be reported when the techniques are used during the pultrusion process.

As long as the non-contact digital printing is not a common standard in the corrugated packaging industry, corrugated board crushing is a real issue that affects the load capacity of the boxes. Crushing mainly occurs during the converting of corrugated board (e.g. analog flexographic printing or laminating) and is a process that cannot be avoided. However, as show in this study, it can be controlled. In this work, extended laboratory tests were carried out on the crushing of double-walled corrugated board. The influence of fully controlled crushing (with a precision: ±10 μm) in the range from 10 to 70 % on different laboratory measurements was checked. Most of the typical mechanical tests were performed e.g. edge crush test, four-point bending test, shear stiffness test, torsional stiffness test, etc. on reference and crushed specimens. The residual thickness reduction of the crushed samples was also controlled. All empirical observations and performed measurements were the basis for building an analytical model of crushed corrugated board. The proven and verified model was then used to study the crushing effect of the selected corrugated board on the efficiency of simple packages with various dimensions.

This paper reveals the physical properties of Jeffery nanofluid flow past a moving plate embedded in porous medium under the existence of radiation and thermal diffusion. The analysis is carried out in three cases of moving plate, namely stationary plate λ = 0, forth-moving plate λ = 1, back-moving plate λ = −1. Finite difference method is applied to solve the governing equations of the flow and pointed out the variations in velocity, temperature and concentration with the use of graphical presentations. The impact of several parameters on local skin friction, Nusselt number and Sherwood number is also noticed and discussed. Enhancement of velocity is observed under the impact of Jeffery parameter for the cases of stationary plate and back-moving plate, whereas reverse nature is found in the case of forth-moving plate. The velocity enhances as the values of porosity parameter increases for the case of stationary plate and forth-moving plate but a reverse nature is noticed in the case of back-moving plate.

Over the last few decades, ocean research and exploration have made underwater mechanical systems a necessity. Underwater vehicles provide a new kind of marine platforms that could represent a great necessity in many areas of oceanographic research. Until now, the underwater vehicles come in a verity of shapes, sizes and means of propulsion. Depending on these characteristics, the type and mission of the vehicle are also determined. The underwater robots are used for different inspection and intervention missions in e.g. the oil and gas industry, ocean science research. Due to multiple applications to which the vehicle can participate, it can be successfully used and to determine methods of re-use of marine energy. Environmental mapping provides accurate information about the main areas of interest of the energy, as well as the exploitation possibilities of that. Most of the time, biomimetic robots were inspired their senso structure, from different kind of animals, such as insects, fish and birds. Nowadays, the concept of a underwater robotic vehicles capable to move independently, autonomously or remotely, has a great potential and a large application. This is the reason that the last studies have been directed on biomimetic robots. The fish and other underwater animals have evolved superior swimming capabilities in many ways and represent a starting point to explain the fluid-mechanical principles. Furthermore, the underwater animals develop and achieve extraordinary propulsion efficiencies, acceleration and maneuverability. They can also achieve high speed under water. Implanting and creating a vehicle through a biomimetic approach reduces the energy used to maneuver the vehicle as it can automatically correct its position and displacement. The paper presents an examination of the state of biomimetic robotic fishes, underlining the reason why bio-inspiration can help us in the underwater locomotion technology.

The generalized Kuramoto–Sivashinsky equation is investigated using the modified Kudrayshov method for the exact analytical solution. The modified Kudrayshov method converts the nonlinear partial differential equation to algebraic equations, as a result of various steps, which on solving the so obtained equation systems yields the analytical solution. By this way various exact solutions including complex structures are found and drawn their behaviour in complex plane by Maple to compare the uniqueness of solutions.

The streptavidin and biotin interaction is one of the strongest non-covalent interactions in nature. As a result, this non-covalent interaction has been of great interest when it comes to biochemical assays, diagnosis of diseases, and cell-targeted drug delivery. Past research has proven that biotin-streptavidin is useful in biosensor development to improve the detection of a system when conjugated to nanoparticles. This study aims to prove that streptavidin-coated nanoparticles can be conjugated with biotinylated antibodies using the primary-secondary method to non-invasively detect adenocarcinoma in-vitro. While the use of nanoparticles is not uncommon to the diagnostics area of scientific research, the technique this research aims to investigate is a non-invasive one, utilizing the primary-secondary method. Specifically, the increased stability of fluorophores when bound to antibodies as opposed to nanoparticles directly can be indicative of the particles conjugated through the primary-secondary method’s ability to specifically bind to overexpressed transferrin receptors in the A549 cell line. In this paper, streptavidin-coated nanoparticles were conjugated with biotinylated anti-transferrin receptor antibodies and AlexaFluor-488 secondary antibodies were used to enable fluorescence-based detection. The efficiency of these particles were observed quantitatively through a plate reader and qualitatively through a fluorescence microscope. I demonstrated that these nanoparticles are able to specifically bind to the target proteins in this study. These findings contribute to the field of nanoparticle diagnostics and can be extended to different diseases caused by overexpression of proteins in the future. While this was conducted in-vitro, conjugates can be prepared to detect cancer in-vivo and can be tested with magnetic relaxometry in the future.

The role of the immune response to SARS-CoV-2 infection is not yet well known, in particular about the persistence of circulating antibodies. The aim of the study is to compare the results of two automated systems for the determination of IgG antibodies against SARS CoV-2 and to assess the time course of the IgG response after the onset of symptoms for a period longer than that evaluated to date. IgG were measured in 98 specimens of 55 subjects with COVID-19 (time from the onset of symptoms from 3 to 109 days) using the automated tests "Abbott SARS-COV-2 IgG" and the "MAGLUMI 2019-nCoV IgG". The two methods had a concordance of 91.8%, but the quantitative correlation showed very dispersed results. All the specimens resulted positive after 17 days from the onset of the synptoms. However, the median concentrations of IgG, after a rapid increase up to about 20 days, quickly decrease to about 15% of the maximum for Maglumi. The same samples measured by Architect showed a quite constant trend up to 80 day, and then an only moderate decline. The titer of IgG against SARS-CoV-2 in patients exposed to COVID-19 may significantly and rapidly decrease, with a different time-course depending on the method used for the determination.

In this paper, the definition of information entropy of Smoluchowski coagulation equation for Brownian motion is introduced based on coagulation probability. The expression of entropy is the function of geometric average particle volume and standard deviation with lognormal distribution assumption. The asymptotic solution with moment method shows that the entropy is a monotone increasing function of time, which is equivalence to the entropy based on particle size distribution. the result reveals that the present definition of entropy of Smoluchowski coagulation equation are inadequate because the particle average volume at equilibrium cannot be determined from the principle of maximum entropy. This provides a basis for further exploring the global properties of Smoluchowski coagulation equation.

This communication reports an improvement of the quality of the electrical data obtained from the application of electrical resistivity tomography method on archaeological studies. The electrical contact between ground and electrode enhances significantly by using carbomer-based gel during the electrical resistivity tomography measurements. Not only does the gel promote the conservation of the building surface under investigation, but it also virtually eliminates the necessity of conventional spike electrodes, which in many archaeological studies are inadequate or not permitted. Results evidenced an enhancement in the quality of the electrical data obtained in the order of thousands of units compared with those without using the carbomer-based gel. The potential and capabilities of this affordable gel make it appropriate to be applied to other geoelectrical studies beyond archaeological investigations. Moreover, it might solve corrosion issues on conventional spike electrodes, and electrical multicore cables usually provoked for added saltwater attempting to improve the electrical contact.

In this paper, we use three different experimental methods (particle method, grid method and hybrid method) to model and simulate the smoke from the perspective of fluid dynamics. Through the comparison of different methods, we conclude: The particle method can avoid the numerical dissipation problem caused by grid calculation, but it also brings problems such as the distortion of the trajectory of the example. The grid method is accurate in calculation, but it is prone to numerical dissipation and loss of details. Finally, we choose the hybrid method to store the vorticity in the form of particles in vortex particles, avoiding the numerical dissipation problem caused by the use of grids, and including rich turbulence, which perfectly shows the simulation effect of smoke.

The scarcely investigated myxobacterium Corallococcus coralloides holds a large genome containing many uncharacterized biosynthetic gene clusters (BGCs) that potentially encode the synthesis of entirely new natural products. Despite its promising genomic potential, suitable cultivation conditions have not yet been found to activate the synthesis of new secondary metabolites (SMs). Finding the right cultivation conditions to activate BGCs in the genome remained a major bottleneck and its full biosynthetic potential was so far not retrieved. Here, we therefore applied a bivariate OSMAC approach, using a combination of two elicitor changes at once for activation of BGCs and concomitant SM production by C. coralloides. The bivariate OSMAC screening was carried out in 24-well System Duetz-plates, applying univariate and bivariate OSMAC conditions. We combined biotic additives and organic solvents with minimal media and complex growth medium. The success of the method was evaluated by the number of new mass features detected in the respective extracts. We found synergistic effects in bivariate OSMAC designs. The number of new mass features detected in bivariate OSMAC exceeded the sum of new mass features found in the respective univariate OSMAC with only one elicitor. Overall, the bivariate OSMAC screening led to 26 new mass features, which were not detected in the univariate OSMAC design. Hence, the presence of multiple elicitors in the bivariate OSMAC designs successfully activated the biosynthetic potential in C. coralloides. We propose the bivariate OSMAC designs with a complex combination of elicitors as a straightforward strategy to robustly expand the SM space of microorganisms with large genomes.

Based on Venturini method, it is in favor of the modulation technique for controlling the matrix converter due to only use of the comparison between the duty cycles in time domain and the triangular carrier wave for generating the gating signals and the achievable voltage ratio between fundamental output magnitude and fundamental input magnitude to 0.866. However, even with simple modulation method and achieving maximum fundamental output magnitude, the possible input voltage unbalance conditions accordingly influence on the output performances (more reduction and distortion). Thus, a modified Venturini modulation method is presented in this paper, in order to solve the problems of unbalanced input voltage conditions on the matrix converter performances. The proposed strategy is to satisfy the desirable feature of the duty cycle modulating waves, as generated in the event of normal situation. Up to this approach, it can support either single-phase condition or two-phase condition. Performance of the proposed control strategy was verified by the simulated implementation in the MATLAB/Simulink software with showing good steady-state and dynamic operations.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

This research takes Cuiwei Village in Qianshan District of Zhuhai City as an example. Through field research, the village is investigated and analyzed, and the street scale, spatial structure, functional characteristic streets, internal commercial distribution forms, and functions of Cuiwei Historic District are studied. analysis. On this basis, based on the convex space method and the line-of-sight analysis method in the space syntax theory, with the help of Depthmap software, the complex street node, that is, the space of the two nodes A and B, is established through the establishment of a visual field model. It includes the analysis of the integration degree of the horizon, the concentration of the horizon, the connection value of the horizon and the spatial characteristics of the historical area, as well as the traditional buildings that are the most representative of the village, namely the Three Kings Temple and the Webster's Mansion. When R=N and radius R=3, observe the changes in the two parameters of the visual integration and visual depth of the two historical buildings. And with the help of Baidu Time Machine photos in different periods to observe and record the changes in the store and the characteristics of people's behavior, and draw conclusions.

The calculation of the surface tension of ordinary organic and ionic liquids, based on a computer algorithm applying a refined group-additivity method, is presented. The refinement consists of a complete breakdown of the molecules into their constituting atoms, further distinguishing them by their immediate neighbour atoms and bond constitution. The evaluation of the atom-groups’ contributions was carried out by means of a fast Gauss-Seidel fitting method founded upon the experimental data of 1895 compounds from literature. The result has been tested for plausibility using a 10-fold cross-validation (cv) procedure. The direct calculation and the cv test proved the applicability of the present method by the close similarity and excellent goodness of fit R2 and Q2 of 0.9023 and 0.8821, respectively. The respective standard deviations are ±2.01 and ±2.16 dyn/cm. Some correlation peculiarities have been observed in a series of ordinary and ionic liquids with homologous alkyl chains which are illustrated and discussed in detail, exhibiting the limit of the present method.

Coastal rural areas can be a source of elemental mercury, but the potential influence of their topographic and climatic particularities on gaseous elemental mercury (GEM) fluxes have not been investigated extensively. In this study gaseous elemental mercury was measured over Mediterranean coastal grassland located at Northern Greece from 2014 to 2015 and GEM fluxes were evaluated utilizing Monin-Obukhov similarity theory. The GEM fluxes ranged from -50.30 to 109.695 ng m-2 h-1 with a mean value equal to 10.501 ng m-2 h-1 ± 19.14 ng m-2 h-1. Concerning the peak events, with high positive and low negative GEM fluxes, those were recorded from the morning until the evening. Rain events were a strong contributing factor for enhanced GEM fluxes. The enhanced turbulent mixing under daytime unstable conditions led to greater evasion and positive GEM fluxes while during nighttime periods the GEM evasion is lower indicating the effect of atmospheric stability on GEM fluxes. The coastal grassland with its specific characteristics influences the GEM fluxes and this area could be characterized as source of elemental mercury. This study is one of the rare efforts in the research community to estimate GEM fluxes in a coastal natural site based on aerodynamic gradient method.

Steel is one of the essential materials in the world's civilization. It is essential to produce many products such as pipelines, mechanical elements in machines, vehicles, profiles, and beam sections for buildings in many industries. Until the '50s of the 20th century, steel products required a complex process known as ingot casting; for years, steelmakers focused on developing and simplifying this process. The result was the con-tinuous casting process (CCP); it is the most productive method to produce steel. The CCP allows producing significant volumes of steel sections without interruption and is more productive than the formal ingot casting process. The CCP begins by transferring the liquid steel from the steel-ladle to a tundish. This tundish or vessel distributes the liquid steel, by flowing through its volume, to one or more strands having wa-ter-cooled copper molds. The mold is the primary cooling system, PCS, solidifying a steel shell to withstand a liquid core and its friction forces with the mold wall. Further down the mold, the rolls drive the steel section in the SCS. Here the steel section is cooled, solidifying the remaining liquid core, by sprays placed in every cooling segment all around the billet and along the curved section of the machine. Finally, the steel strand goes towards a horizontal-straight free-spray zone, losing heat by radiation mechanism, where the billet cools down further to total solidification. A moving torch cutting-scissor splits the billet to the desired length at the end of this heat-radiant zone.

The eddy current loss should be optimized to be as less as possible for the stability of permanent magnet in high speed permanent magnet synchronous motor (HSPMSM) rotor and ensure the high efficiency and low temperature of the motor. This paper analyzes the eddy current distribution in rotor, with consideration of the conflict of the thickness of sleeve and diameter of the rotor, calculating the eddy current loss (ECL) and the thermal distribution via Separation of variables method for solving Maxwell's equations with analytical hieratical model of ECL constructed. The optimization result of ECL of the HSPMSM whose power and rated speed is 30kw 48000r/min can be got by multi-objective optimization method, combined weighting coefficient method and traversal algorithm based on chaotic local search particle swarm optimization (CLSPSO), utilizing ECL analytical model and other analytical constraints. Related experiment and measurement has been implemented with new approach of loss separation.

Globally 30% of landslides occur in the northeastern part of India [1]. One of the major earthquake events in Sikkim, India occurred on 18th September 2011 (Mw 6.9) led to over 300 landslides and 122 human deaths [2]. These landslides not only controlled by natural disasters but initiated due to human activities. The present study considered Lungchok landslide occurred in south district of Sikkim due to 2011 seismic event. The study focused on the failure mechanism of the landslide based on finite element analysis by adopting eight different cases. The deformation characteristic was investigated for dry and saturated slope conditions under static and dynamic behavior considering vehicle loads using GeoStudio software. The FEM analysis has been carried out using load deformation and linear elastic. The analysis shows that the failure of the slope was not sudden due to the 2011 earthquake event, but progressive failure was observed with time and construction activity. The paper demonstrates that, an increase in infrastructure development including construction by hill cutting increased the initiation of landslide with soil erosion. The cracks developed after 2011 earthquake event led to further deformations during future disasters required effective stabilization measures.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration proles.

Trade of agricultural products has gained importance with the development of global trade. Cherries has a crucial place in Turkish agricultural exports. Fresh cherries are in the scope of this study. The aim of this study is to examine Turkey’s position and competitiveness in cherry trade. Trade Intensity Analysis Method which represents the course of trade flow among countries is used in the study. The study indicates that European countries which are Turkey’s tradition trade partner has a biggest trade share with Turkey and that share did not much change in years. By the way, Asia market especially China, became a game changer in cherry trade and Turkey should prepare itself for this situation.

This article deals with the conformable double Laplace transforms and their some properties with examples and also the existence Condition for the conformable double Laplace transform is studied. Finally, in order to obtain the solution of nonlinear fractional problems, we present a modified conformable double Laplace that we call conformable double Laplace decomposition methods (CDLDM). Then, we apply it to solve, Regular and singular conformable fractional coupled burgers equation illustrate the effectiveness of our method some examples are given.

According to the current European and Italian scenario related to urban re-generation, cultural and landscape heritage, valorisation is being also enhanced by the activation of innovative processes. These involve the development of methodologies and tools that are able to address decision-making processes among low entropy economy, complex values and creative practices. In this perspective, the research aims to investigate the possibilities of developing a Cultural Heritage Low Entropy Enhancement (CHLEE) approach by considering how the complex values of cultural heritage can vary not only through a physical transformation of spaces but also through a program of uses and activities able to produce new values, where the human experience is essential. This type of model modifies the objectives that characterise the valorisation of cultural heritage and landscape, recognising that the fruition is no longer “consumerist” but “experiential”. A crucial role is represented by the heterogeneity of creative practices that contribute to the identificationidentifying and implementation ofimplementing innovative management and governance models. The present paper explores the components of creative regenerative processes, based upon the ex-post evaluation of some Italian experiments, across the PROMETHEE-GAIA multi-criteria method, to understand how creative experiences are building innovation ecosystem thanks to low entropy economy and improve the ex-ante evaluation for new strategies and policies.

Voltage sags can cause the interruption of power supply and can negatively affect operations of customers. In this paper, the authors study the impact of battery energy storage systems (BESS) on voltage sags. A stochastic method of fault positions is used. Faults of various types are simulated and voltages are recorded. Firstly, with the BESS integrated into the network, there are higher residual voltages, fewer voltage sags and less expected critical voltage loss. Secondly, if the BESS converter power factor is reduced, recorded residual voltages are higher, voltage sags are fewer, and the number of expected critical voltage sags is lower. Finally, when three BESS converter control modes, namely constant voltage, constant power factor, and constant reactive power, were assessed, results showed similar voltage sag performances for constant power factor and constant reactive power modes. Furthermore, operating in constant voltage control outperformed the other two modes as it resulted in higher residual voltages, a lower number of voltage sags, and fewer expected critical voltage sags. The paper has demonstrated that the BESS can improve voltage sag performance. In addition, the power factor of the BESS converter and the mode of operation of the converter can influence the magnitude of the voltage sag performance improvement.

In recent years, the management of health systems is a main concern of governments and decision makers. Home health care is one of the newest methods of providing services to patients in developed societies that can respond to the individual lifestyle of modern age and the increase of life expectancy. The home health care routing and scheduling problem is a generalized version of the vehicle routing problem, which is extended to a complex problem by adding special features and constraints of health care problems. In this problem, there are multiple stakeholders such as nurses for which an increase of their satisfaction level is very important. In this study, a mathematical model is developed to expand traditional home health care routing and scheduling models to downgrading cost aspects by adding the objective of minimizing the difference between the actual and potential skills of the nurses. Downgrading can lead to a dissatisfaction of the nurses. In addition, skillful nurses have higher salaries and high-level services increase equipment costs and need more expensive trainings and nursing certificates. Therefore, downgrading can enforce hidden huge costs to the managers of a company. To solve the bi-objective model, an -constraint based approach is suggested and the model applicability and its ability to solve the problem in various sizes are discussed. A sensitivity analysis on the Epsilon parameter is conducted to analyze the effect of this parameter on the problem. Finally, some managerial insights are presented to help the managers in this field, and some directions for future studies are mentioned as well.

The concept of transformative resilience emerges from complex recent literature and represents a way to interpret the potential opportunities to change in vulnerable territories, where a socio-economic change is required. This article extends the perspective of transformative resilience to assessing of the landscape multi-functionality of inland areas, exploring the potentials to identify a network of synergies among the different municipalities able to trigger a process of territorial resilience. A Spatial Decision Support System (SDSS) for multi-functionality landscape assessment aims to support the local actors to understand local resources and multi-functional values of the Partenio Regional Park (PRP) and surrounding municipalities, in the South of Italy, stimulating their cooperation to the management of environmental and cultural sites and the co-design of new strategies of enhancement.

Demographic change is leading to the aging of German society. As long as the baby boom co-horts are still of working age, the working population will also age - and decline as soon as this baby boom generation gradually reaches retirement age. At the same time, there has been a trend towards increasing absenteeism (times of inability to work) in companies since the zero years, with the number of days of absence increasing with age. We present a novel stochastic forecast approach that combines population forecasting with forecasts of labor force participation trends, considering epidemiological aspects. For this, we combine a stochastic Monte Carlo-based cohort-component forecast of the population with projections of labor force participation rates and morbidity rates. This article examines the purely demographic effect on the economic costs associated with such absenteeism due to the inability to work. Under expected future employment patterns and constant morbidity patterns, absenteeism is expected by close to 5 percent by 2050 relative to 2020, associated with increasing economic costs of almost 3 percent. Our results illustrate how strongly the pronounced baby boom/ baby bust phenomenon determines demographic development in Germany in the midterm.

In the study, a new correction method was applied to reduce error during detection on mixed pesticide residue in apples by using Raman spectra. Combined with self-built pesticide residues detection system by Raman spectroscopy and the application of surface enhancement technology, rapid real-time qualitative and quantitative analysis of deltamethrin and acetamiprid residues in apples can be applied effectively. In quantitative analysis, compared with the intensity value of characteristic peaks of single pesticide with same concentration, the intensity value of characteristic peaks of the two pesticides decreased after mixing the pesticides, which interferes the results severely. By comparing the difference in the intensity of characteristic peaks of single and mixed pesticides, a correction method is proposed to eliminate the influence of pesticides mixture. Characteristic peak intensity values of gradient concentration pesticide from 10-1 g•kg-1 to 10-6 g•kg-1 and Lagrangian interpolation are applied in the correction method. And a smooth surface is applied to describe the correction ratio of characteristic peak intensity. Through detecting the characteristic peak intensity values of the mixed pesticide, correction ratio will be obtained. Then real values of the peak intensity of pesticides and the content of each component of the mixed pesticide will be acquired by the correction method. Correlation coefficient of model validation exceeds 0.88 generally and Root Mean Square Error also decreases obviously after correction, which proved the reliability of the method.

Sterepinic acids A–C (1–3), new carboxylic acids with two primary alcohols, have been isolated from a fungal strain of Stereum sp. OUPS-124D-1 attached to the marine alga Undaria pinnatifida. Dihydro-1,5-secovibralactone (4), a new vibralactone derivative, was isolated from the same fungal metabolites together with known vibralactone A (5), and 1,5-secovibralactone (6). The planar structures of these compounds have been elucidated by spectroscopic analyses using IR, HRFABMS, and NMR spectra. To determine the absolute configuration of the compounds, we used the phenylglycine methyl ester (PGME) method. These compounds exhibited less activity in the cytotoxicity assay against cancer cell lines.

The load on the top of a slope is an important cause of slope failure, and it is of great significance to study the relationship between the load and the stability of the slope. This paper uses elastic theory and Moore Coulomb's theory as transformation conditions to obtain the slope stability coefficient expression under slope top load based on the Swedish slice method. In view of the actual engineering, the corresponding slope model structure was established, and 5 sliding surfaces were set with the crack on the top of the slope as the shear outlet. According to the slope stability coefficient expression, the stability coefficient of the set sliding surface is solved. The result shows that the slope is unstable under the load. The judgment result is consistent with the GEO-STUDIO check calculation result. This method can provide reference for theory and engineering practice.

Although the Slicing Method (SM) is effective for calculating the volume of point cloud objects (PCOs), it is restricted in terms of applicability and practicability because of a certain contingency and directional defects. The Co-Opposite-Direction Slicing Method (CODSM) proposed in this paper is an improved method for calculating PCO volume by increasing parallel (co-opposite-direction) observation and considering the two-way mean as the result. This method takes full advantage of the mutual offsetting of random errors and the compensation of systematic directional errors, which can effectively overcome (or mitigate) the effect of random errors and reduce the effect of systematic errors in SM. In this paper, two typical objects, a cone model and a stone lion base, are the examples for calculating PCO volume using CODSM. The results show that CODSM has all the inherent advantages of SM and effectively weakens the volatility of random errors and the directionality of systematic errors from SM. Therefore, CODSM is a robust configuration upgrade of SM.

In this case study, an active runway of a civilian airport in Zonguldak, Turkey, is used to assess the suitability of spaceborne digital elevation models (DEMs) to model an anthropogenic structure. The tested DEMs include the ASTER, the AW3D30 m, the SRTM-1”, the SRTM-3”, the SRTM-X, the TanDEM-3”, and the WorldDEMTM. A photogrammetric high accuracy DEM was also available for the tests. As a reference dataset, a line leveling survey of the runway using a Leica Sprinter 150/150M instrument was performed. The selection of a runway as a testbed for this type of investigation is justified by its unique characteristics, including its flat surface, homogenous surface material, and availability for a ground survey. These characteristics are significant because DEMs over similar structures are free from environment- and target-induced error sources. The most accurate DEM is the WorldDEMTM followed by the SRTM-3” and TanDEM-3”, with vertical errors (LE90) equal to 1.291 m, 1.542 m, and 1.56 m, respectively. This investigation uses a method for identifying the vertical errors in DEMs that is known as the runway method.

An in-depth study of the failure of granular materials, which is known as a mechanism to generate defects, can reveal the facts about the origin of the imperfections such as cracks in the carbon anodes. The initiation and propagation of the cracks in the carbon anode, especially the horizontal cracks below the stub-holes, reduce the anode efficiency during the electrolysis process. In order to avoid the formation of cracks in the carbon anodes, the failure analysis of coke aggregates can be employed to determine the appropriate recipe and operating conditions. In this paper, it will be shown that a particular failure mode can be responsible for the crack generation in the carbon anodes. The second-order work criterion is employed to analyze the failure of the coke aggregate specimens and the relationships between the second-order work, the kinetic energy, and the instability of the granular material are investigated. In addition, the coke aggregates are modeled by exploiting the discrete element method (DEM) to reveal the micro-mechanical behavior of the dry coke aggregates during the compaction process. The optimal number of particles required for the failure analysis in the DEM simulations is determined. The effects of the confining pressure and the strain rate as two important compaction process parameters on the failure are studied. The results reveal that increasing the confining pressure enhances the probability of the diffusing mode of the failure in the specimen. On the other hand, the increase of strain rate augments the chance of the strain localization mode of the failure in the specimen.

During the past two decades of e-commerce growth, the concept of a business model has become increasingly popular. More recently, the research on this realm has grown rapidly, with diverse research activity covering a wide range of application areas. Considering the sustainable development goals, the innovative business models have brought a competitive advantage to improve the sustainability performance of organizations. The concept of the sustainable business model describes the rationale of how an organization creates, delivers, and captures value, in economic, social, cultural, or other contexts, in a sustainable way. The process of sustainable business model construction forms an innovative part of a business strategy. Different industries and businesses have utilized sustainable business models’ concept to satisfy their economic, environmental, and social goals simultaneously. However, the success, popularity, and progress of sustainable business models in different application domains are not clear. To explore this issue, this research provides a comprehensive review of sustainable business models literature in various application areas. Notable sustainable business models are identified and further classified in fourteen unique categories, and in every category, the progress -either failure or success- has been reviewed, and the research gaps are discussed. Taxonomy of the applications includes innovation, management and marketing, entrepreneurship, energy, fashion, healthcare, agri-food, supply chain management, circular economy, developing countries, engineering, construction and real estate, mobility and transportation, and hospitality. The key contribution of this study is that it provides an insight into the state of the art of sustainable business models in various application areas and future research directions. This paper concludes that popularity and the success rate of sustainable business models in all application domains have been increased along with the increasing use of advanced technologies.

Use of Machine Learning (ML) methodologies in optical communications has paved a new pathway. In this paper, firstly, we discuss the use of ML methodologies for reducing optical fiber nonlinearities, nonlinearity compensation, fault detection and optical performance monitoring. Then we present our recent work where we compare RL-SARSA and SVM based method with conventional method. The results show that RL-SARSA and SVM methods are successful candidates in mitigating the nonlinearities in proposed system as compared to conventional optical communication system.

CO2 emissions resulting from the production of cement is a major issue, but can be limited by the partial substitution of cement by low-carbon-impact additions. The aim of this study was the formulation of a ternary binder based on ordinary Portland cement (OPC), ground granulated blast-furnace slag (GGBS) and flash-calcined sediment (FCS), a dredged waste which was valorized after applying a new heat treatment: flash calcination. The used materials were physically, chemically and mineralogically characterized. The composition of the formulations was optimized using mixture designs. Five formulations, one reference formulation RM (100% OPC), one binary formulation (50% OPC/50% GGBS), and three ternary formulations with a variable FCS rate (10%, 15%, 20%), were selected and characterized fresh and hardened. Results showed that the incorporation of FCS reduced the workability and increased the density. In addition, a decrease in the initial setting time and the heat of hydration peak were observed. In the hardened state, the formulation containing 10% FCS showed 90-day mechanical strengths superior to that of RM. The use of FCS in ternary binders could reduce the environmental impact by reducing greenhouse gas emissions.

The present work deals with the development of finite element methodology for obtaining the stress distributions in thick cylindrical HK40 stainless steel pipe that carry high temperature fluids. The material properties and loading are assumed to be random variables. Thermal stresses that are generated along radial, axial and tangential directions are computed generally using analytical expressions which are very complex. To circumvent such an issue, the probability theory and mathematical statistics have been applied to many engineering problems which allows to determine the safety both quantitatively and objectively based on the concepts of reliability. Monte Carlo simulation methodology is used to study the probabilistic characteristics of thermal stresses which is used for estimating the probabilistic distributions of stresses against the variations arising due to material properties and load. A 2-D Probabilistic finite element code is developed in MATLAB and the deterministic solution is compared with ABAQUS solutions. The values of stresses that are obtained from the variation of elastic modulus are found to be low as compared to the case where the load alone is varying. The probability of failure of the pipe structure is predicted against the variations in internal pressure and thermal gradient. These finite element framework developments are useful for the life estimation of piping structures in high temperature applications and subsequently quantifying the uncertainties in loading and material properties.

In this paper, we gave an attack on RSA when Euler function has small multiplicative inverse modulo "e" and the prime sum p+q is of the form p+q=2^nk_0+k_1 where n is a given positive integer and k_0 and k_1 are two suitably small unknown integers using sublattice reduction techniques and Coppersmith's methods for finding small roots of modular polynomial equations. When we compare this method with an approach using lattice based techniques, this procedure slightly improves the bound and reduces the lattice dimension.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densi- ties and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on dierent set of true values. Some real data sets were employed to show the usefulness and exibility of the model which serves as generalization to many sub-models in the elds of engineering, medical, survival and reliability analysis.

This article describes the use of the PI ProcessBook software tool for visualization and indirect monitoring of occupancy of SHC rooms from the measured operational and technical quantities for monitoring of daily living activities for support of independent life of elderly persons. The proposed method for data processing (predicting the CO₂ course using neural networks from the measured temperature indoor T_i (°C), temperature outdoor T_o (°C) and the relative humidity indoor rHi (%)) was implemented, verified and compared in MATLAB SW tool and IBM SPSS SW tool with IoT platform connectivity. Within the proposed method, the Stationary Wavelet Transform de noising algorithm was used to remove the noise of the resulting predicted course. In order to verify the method, two long-term experiments were performed, (specifically from February 8 to February 15, 2015, from June 8 to June 15, 2015) and two short-term experiments (from February 8, 2015 and from June 8, 2015). For the best results of the trained ANN BRM within the prediction of CO₂, the correlation coefficient R for the proposed method was up to 90%. The verification of the proposed method confirmed the possibility to use the presence of persons of the monitored SHC premises for rooms ADL monitoring.

Background: Developing an efficient and standardized method to isolate and characterize adipose-derived stem cells (ASCs) from the stromal vascular fraction (SVF) of the adipose tissue for clinical application represents one of the major challenges in cell therapy and tissue engineering. Methods: In this study, we proposed an innovative, non-enzymatic protocol to collect clinically useful ASCs within freshly isolated SVF from adipose tissue by centrifugation of the infranatant portion of lipoaspirate and to determine the characteristic cytofluorimetric pattern, prior to in vitro culture. Results: The SVF yielded a mean of 73,32 \pm\ 10,89% cell viability evaluated with CALCEINA-FITC, i.e. cell-permeant dye. The ASCs were positive for PC7-labeled mAb anti-CD34 and negative for both PE-labeled mAb anti-CD31 and APC-labeled mAb anti-CD45. The frequency of ASCs estimated according to the panel of cell surface markers used was 51,06%\ \pm 5,26% versus the unstained ASCs subpopulation that was 0,74%\pm0,84% (P<0.0001). The ASCs events/\muL were 1602,13/\muL \pm 731,87/\muL. Conclusion: Our findings suggested that ASCs found in freshly isolated adipose SVF obtained by centrifugation of lipoaspirate can be immunophenotypically identified with a basic panel of cell surface markers. These findings aimed to provide standardization and contribute to reducing the inconsistency on reported cell surface antigens of ASC derived from the existing literature.

Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost variances using proprietary C-S and S-C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

Working capital management requires a careful attention by the corporate managers because it plays an important role in corporate stability. Social belongingness of managers induced them to learn from their society, colleagues and from overall industrial movement. They also learn from their peers which have more strategical efficiency. In line with these arguments, the objective of current study is to explores the peer influence on corporate working capital management practices. To making analysis, ten-years data (2009-2018) of non-financial publicly listed firms at PSX were collected and the cash conversion cycle (CCC) uses as a proxy variable of working capital management (WCM). To estimate the regression, an econometric technique named the Generalized Method of Moments (GMM) was used. The empirical findings suggest the significant impact of peer WCM on corporate WCM. It also suggests the significant impact of other variables that determine the WCM. This study recommends social learning policy to corporate managers. They can learn from their peers to manage the working capital. Most previous studies discuss the peer influence on investment decisions, corporate cash holding and financing policy, etc., but no study explores such a relationship specifically in the Pakistani non-financial sector data set.

In recent years, numerous topologies of single phase and three phase Field Excited Flux-Switching Machine (FEFSM) have been developed for several applications. Comparative study of three types of single-phase low-priced Field Excited Flux-Switching Machine (FEFSM) is presented in this paper. Both the conventional 8S/4P sub-part rotor design and 6S/3P salient rotor design have an overlapped winding arrangements between armature coil and field excitation coil that depicts high copper losses as well as results in increased size of motor. Additionally, FEFSM with salient structure of the rotor have high flux strength in the stator-core that has much impact on high iron losses. Copper consumption and iron loss being a crucial proportion in total machine losses. Therefore a novel topology of single phase modular rotor field excited FSM with 8S/6P configuration is proposed, which enable non-overlap arrangement between armature coil and FEC winding that facilitates devaluation in the copper losses. The proposed modular rotor design acquires reduced iron losses as well as reduced active rotor mass comparatively to conventional rotor design. It is very persuasive to analyze the best range of speed for these rotors to avoid cracks and deformation, the maximum tensile strength (can be measured with principal stress in research) of the rotor analysis is conducted using JMAG. A deterministic optimization technique is used to enhance the performance of 8S/6P modular rotor design. The electromagnetic performance of conventional sub-part rotor design, F1-A3-3P design and proposed novel-modular rotor design are analyzed by 3D-Finite Element Analysis (3D-FEA), includes flux linkage, flux distribution, flux strength, back-EMF, cogging torque, torque characteristics, iron losses and efficiency.

To gain insight into riser motions and associated fatigue damage due to vortex-induced vibration (VIV), data loggers such as strain sensors and/or accelerometers are sometimes deployed on risers to monitor their motion in different current velocity conditions. Accurate reconstruction of the riser response and empirical estimation of fatigue damage rates over the entire riser length using measurements from a limited number of sensors can help in efficient utilization of the costly measurements recorded. Several different empirical procedures are described here for analysis of the VIV response of a long flexible cylinder subjected to uniform and sheared current profiles. The methods include weighted waveform analysis (WWA), proper orthogonal decomposition (POD), modal phase reconstruction (MPR), a modified WWA procedure, and a hybrid method which combines MPR and the modified WWA method. Fatigue damage rates estimated using these different empirical methods are compared and cross-validated against measurements. Detailed formulations for each method are presented and discussed with examples. Results suggest that all the empirical methods, despite different underlying assumptions in each of them, can be employed to estimate fatigue damage rates quite well from limited strain measurements.

It is important for enterprises to decide their environmental policies after carefully examining their future paths based on the relationship between the environment and the economy. This study focused on Japanese minimum administrative divisions (municipalities) and attempted to quantify the annual environmental efficiency of production activities within each division according to the theory of life-cycle impact assessment (LCIA). This study leverages the assessment theory LIME2, which is an endpoint-type LCIA method developed in 2010 that integrates environmental loads for certain impact categories, such as global warming and land use into a simple indicator by monetary unit. First, annual environmental impact assessments were conducted for all Japanese municipalities based on statistical information that was reliable, verifiable, and comparable. Next, the environmental efficiency of productivity for each division was conceptualized by dividing the gross domestic product by the environmental damage amounts as calculated above. Assessment results for each municipality were placed on a map of Japan in order to visualize the regionality of each indicator. The findings revealed in this study will aid public administrators in their decision-making process with respect to environmental policies.

International guidelines are published in oncology to provide standardized information and fertility preservation (FP) care for adults and children with cancer. For benign gynecologic diseases (BGD), many recommendations are based on data coming from oncofertility studies rather than studies with a stronger and broader evidence base. The purpose of the study was to conduct a modified Delphi process for generating FP guidelines for BGD. A steering committee identified 42 potential FP practices for BGD. Then 114 key stakeholders were asked to participate in a modified Delphi process via two online survey rounds and a final meeting. Consensus was reached for 28 items. Among them, stakeholders rated age-specific information concerning the risk of diminished ovarian reserve after surgery as important but rejected proposals setting various upper and lower age limits for FP. All women should be informed about the benefit/risk balance of oocyte vitrification, in particular about the likelihood of live birth according to age. FP should not be offered in rASRM stages I and II endometriosis without endometriomas. These guidelines could be useful for gynecologists to identify situations at risk of infertility and to better inform women with BGDs who might need personalized counseling for FP.

Riemann’s method is one of the definitive ways of solving Cauchy’s problem for a second order linear hyperbolic partial differential equation in two variables. The first review of Riemann’s method was published by E. T. Copson in 1958. This study extends that work. Firstly, three solution methods were overlooked in Copson’s original paper. Secondly, several new approaches for finding Riemann functions have been developed since 1958. Those techniques are included here and placed in the context of Copson’s original study. There are also numerous equivalences between Riemann functions that have not previously been identified in the literature. Those links are clarified here by showing that many known Riemann functions are often equivalent due to the governing equation admitting a symmetry algebra isomorphic to $SL(2,R)$. Alternatively, the equation admits a Lie-Bäcklund symmetry algebra. Combining the results from several methods, a new class of Riemann functions is then derived which admits no symmetries whatsoever.

In this study, experimental work was carried out on reinforced concrete (RC) beams strengthened with carbon fiber reinforced polymers (CFRP) plates. This study aims to examine the effect of the reinforcement ratio on the flexural behavior of these beams and propose a new model for predicting the debonding moment. Six RC beams consisting of three control beams and three beams strengthened with CFRP plates were tested. The beams were simply supported and loaded with four-point bending. The test variable was the tensile reinforcement ratio (1%, 1.5%, and 2.5%). Analytical prediction using the fiber element method was also carried out to obtain the complete theoretical response of the beam due to flexural loads. The test results show that the reinforcement ratio affected the bending performance of RC beams with CFRP plates. Following this, the experimental data from 60 beam test results from published literature and this study were analyzed. From these data, it was found that the ratio of tensile reinforcement, the ratio of modulus of elasticity of concrete, the modulus of elasticity of the plate, and plate thickness all affect the value of debonding moment. A parametric study using fiber element and two-dimensional finite element method was also carried out to confirm the effect of these parameters on debonding failure. These parameters were then used to develop an equation to predict the debonding moment of RC beams strengthened with CFRP plates using simple statistical analysis. This analysis resulted in a simple model for predicting the debonding moment. Then the model is entered into a computer program, and the complete response of the cross-section due to debonding failure can be obtained.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

Virtual Histology- Intravascular Ultrasound (VH-IVUS) image is an available method for visualizing plaque component to detect thin cap fibroatheroma. Nevertheless, this imaging modality has considerable limitations to extract the plaque component features and identifying the TCFA plaque. The aim of this paper is to improve the identification of TCFA using fusion of IVUS and VH-IVUS images. In order to generate the automatic technique for reducing the human interaction, a new method namely Active Contour based Plaque Border Detection (ACPB) is proposed. In order to perform the pixel wise classification, hybrid of K-means algorithm with Particle Swarm Optimization and Plaque based Minimum Euclidean Distance (KMPSO-PMED) method is presented to classify the plaque region as well. Moreover, to obtain more significant information of imaging modalities, fusion of two different images consisting of VH-IVUS and IVUS is performed. Therefore, geometric features are extracted from the plaque region and combine with IVUS features. Furthermore, different group of plaque features are divided by means of the histopathological studies. SVM classifiers is applied to detect the TCFA and non-TCFA plaques. The proposed method is applied on 566 in-vivo IVUS and their matching VH-IVUS images obtained from 9 patients. The best result of SVM illustrates the accuracy rates of 99.41% for classification of TCFA plaque. The results prove that the highest accuracy is achieved by integrated features of IVUS and VH-IVUS images.

To date, theoretical analyses have provided several useful methods/algorithms for studying transition states and non-covalent interactions. Potential Energy Scan (PES) is one such method that has found wide application in the physicochemical community. Analyzing the PES profiles of the catalytic system of FeBr3 in Electrophilic Aromatic Substitution (EAS) with molecular halogens, one can notice an obvious difference from the modern textbook mechanisms proposed in this area of study. Moreover, the newly presented Graphic Methodology (GM) allows a simple and reliable transition state determination even for very weakly bound charge transfer complexes using second-order derivatives as an efficient tool in the graphical analysis. Relative errors that can be reduced to a few parts per thousand in transition state estimation make this method a potentially very useful tool in further graphical studies of non-covalent interactions. Studies performed using high-precision semiempirical methods suggest that the process of halonium ion quenching proceeds along a completely different pathway, suggesting a possible novel transition metal-nonmetal catalytic system involved in the EAS electrophilic quenching step. The results presented here strongly suggest a future GM application that is widely used and the introduction of pseudo and pre-transition states as new terms in the description of non-covalent interactions.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Obtaining classification confidence at the pixel level is a challenging task for accuracy assessment in remote sensing image classification. Among the various methods for estimating classification confidence at the pixel level, interpolation-based methods have drawn special attention in the literature. Even though they have been widely recognized in the literature, their usefulness has not been rigorously evaluated. This paper conducts a comprehensive evaluation of three interpolation-based methods: local error matrix method, bootstrap method, and geostatistical method. We applied each of the three methods to three representative datasets with different spatial resolutions, spectral bands, and the number of classes. We then derive the estimated classification confidence and true classification confidence and compared the results with each other using both exploratory data analysis (bi-histogram) and statistical analysis (Willmott's d and Binned classification quality). The results indicate that the three interpolation methods provide some interesting insights on various aspects of estimating per-pixel classification confidence. Unfortunately, the interpolation assumes that classification confidence is smooth across the space, which is usually not true in practice. In other words, interpolation-based methods have limited practical use.

This paper is related to the fractional view analysis of Helmholtz equations, using innovative analytical techniques. The fractional analysis of the proposed problems has been done in terms of Caputo-operator sense. In the current methodology, first, we applied the r-Laplace transform to the targeted problem. The iterative method is then implemented to obtain the series form solution. After using the inverse transform of the r-Laplace, the desire analytical solution is achieved. The suggested procedure is verified through specific examples of the fractional Helmholtz equations. The present method is found to be an effective technique having a closed resemblance with the actual solutions. The proposed technique has less computational cost and a higher rate of convergence. The suggested methods are therefore very useful to solve other systems of fractional order problems.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

In order to reveal the mechanism and influencing factors of high pressure jet cavitation of nozzle in submerged environment, this study focused on the evolutionary process of cavitation bubbles and combined finite volume method and mixed multi-phase flow model to analyze the cavitation, velocity distribution and experimental cavitation intensity of fishing net cleaning equipment. Results show that the cavitation inception, growth and collapse mainly occurred in the peripheral region of the flow field. Ring-shaped cavitation erosion zone appeared on the test sample target. A lot of small dense erosion pits were densely distributed in the ring-shaped erosion zone, erosion marks were observed in the center. The cavitation erosion intensity was greatly affected by the nozzle structure. As the diameter of nozzle increased from 0.6 mm to 1 mm, the maximum gas volume fraction increased by 8.53%. The nozzle outlet enlargement angle greatly increased the cavitation intensity. The nozzle with an outlet angle of 30° exhibited the optimal cavitation erosion performance . The cavitation volume fraction of the nozzle with short necking structure was slightly larger than that of the nozzle with long necking structure at the same level in the necking length rang of 3mm to 7mm. In terms of the influence of nozzle structure on the cavitation erosion effect, the nozzle diameter D ranked the first, followed by the outlet angle α, and the necking length L was at the last.

Both drag and lift forces impact an inclined plane when it is dragged through a granular bed. In this paper, the following results have been obtained: the drag and lift forces grow with the velocity of motion; when the immersion depth is constant, the inclination angle has no effect on drag force, however, the lift force increases linearly with this inclination angle; the ratio of drag and lift forces is exactly equal to the tangent value of the inclined angle. In order to describe this physical process macroscopically, a continuum wedge model based on the Coulomb model is established to predict drag and lift forces. Particularly，the dynamic friction angle in the assumed shear band is predicted as a function of both inclined angle and moving velocity.

Soil temperature is a fundamental parameter in water resources and engineering. A cost-effective model which can forecast soil temperature accurately is extensively needed. Recently, many studies have applied artificial intelligence (AI) at both surface and underground levels for soil temperature prediction. However, there is no comprehensive and detailed assessment of the performance of different AI approaches in soil temperature estimation, and primarily limited atmospheric variables are used as input data for AI models. In the present study, great varieties of various land and atmospheric variables are applied to evaluate the performance of a wide range of AI methods on soil temperature prediction. Herein, thirteen approaches, from classic regressions to well-established methods of random forest and gradient boosting to advanced AI techniques like multi-layer perceptron and deep learning are taken into account. The results show that AI is a promising approach in climate parameter forecast and deep learning demonstrates the best performance among other models. It has the highest R-squared ranging from 0.957 to 0.980, the lowest NRMSE ranging from 2.237% to 3.287% and the lowest MAE, ranging from 0.510 to 0.743 in predicting soil temperature. The prediction is repeated for different sizes of data, and prediction outcomes confirm the conclusion mentioned above.

Over the last two decades, residential buildings have accounted for nearly 50 percent of total energy use in New Zealand. In order to reduce household energy use, the factors that influence energy use should be continuously monitored and managed. Building researchers and professionals have made efforts to investigate the factors that affect energy use. However, few have concentrated on the association between household energy use and the cost of residential buildings. This study examined the correlation between household energy use and residential building cost. Analysis of the correlation between energy use data and residential building cost indicated that residential building cost in the construction phase and energy use in the operation stage were significantly correlated. These findings suggest that correct monitoring of building costs can help to identify trends in energy use. Therefore, this study proposes a time series model for forecasting residential building costs of five categories of residential building (one-story house, two-story house, townhouse, apartment, retirement village) in New Zealand. The primary contribution of this paper is the identification of the close correlation between household energy use and residential building costs and provide a new area for optimize energy management.

One of the biggest challenges in characterizing 2-D image topographies is finding a low-dimensional parameter set that can succinctly describe, not so much image patterns themselves, but the nature of these patterns. The 2-D Cluster Variation Method (CVM), introduced by Kikuchi in 1951, can characterize very local image pattern distributions using configuration variables, identifying nearest-neighbor, next-nearest-neighbor, and triplet configurations. Using the 2-D CVM, we can characterize 2-D topographies using just two parameters; the activation enthalpy and the interaction enthalpy. Initial investigations with two different representative topographies (``scale-free-like'' and ``rich club-like'') produce interesting results when brought to a CVM free energy minimum. Additional phase space investigations, where one of these two parameters has been set to zero, identify useful parameter ranges. Careful comparison of the analytically-predicted configuration variables versus those obtained when performing computational free energy minimization on a 2-D grid show that the computational results differ significantly from the analytic solution. The 2-D CVM can potentially function as a secondary free energy minimization within the hidden layer of a neural network, providing a basis for extending node activations over time and allowing temporal correlation of patterns.

In this paper, by using the variational method, a sufficient condition for the unique existence of the stationary solution of the reaction-diffusion ecosystem is obtained, which directly leads to the global asymptotic stability of the unique equilibrium point. Moreover, delayed feedback ecosystem with reaction-diffusion item is considered, and utilizing impulse control results in the globally exponential stability criterion of the delayed ecosystem. It is worth mentioning that the Neumann zero-boundary value that the infected and the susceptible people or animals should be controlled in the epidemic prevention area and not allowed to cross the border, which is a good simulation of the actual situation of epidemic prevention. And numerical examples illuminate the effectiveness of impulse control, which has a certain enlightening effect on the actual epidemic prevention work . That is, in the face of the epidemic situation, taking a certain frequency of positive and effective epidemic prevention measures is conducive to the stability and control of the epidemic situation. Particularly, the newly-obtained theorems quantifies this feasible step. Besides, utilizing Laplacian semigroup derives the $p$th moment stability criterion for the impulsive ecosystem.

In this paper, we study the third order semilocal convergence of the Newton-like method for finding the approximate solution of nonlinear operator equations in the setting of Banach spaces. First, we discuss the convergence analysis under ω-continuity condition, which is weaker than the Lipschitz and Hölder continuity conditions. Second, we apply our approach to solve Fredholm integral equations, where the first derivative of involved operator not necessarily satisfy the Hölder and Lipschitz continuity conditions. Finally, we also prove that the R-order of the method is 2p + 1 for any p $\in$ (0,1].

This paper presents a steady-state and transient heat conduction analysis framework using the polygonal scaled boundary finite element method (PSBFEM) with polygon/quadtree meshes. The PSBFEM is implemented with commercial finite element code Abaqus by the User Element Subroutine (UEL) feature. The detailed implementation of the framework, defining the UEL element, and solving the stiffness/mass matrix by the eigenvalue decomposition are presented. Several benchmark problems from heat conduction are solved to validate the proposed implementation. Results show that the PSBFEM is reliable and accurate for solving heat conduction problems. Not only can the proposed implementation help engineering practitioners analyze the heat conduction problem using polygonal mesh in Abaqus, but it also provides a reference for developing the UEL to solve other problems using the scaled boundary finite element method.

In this lecture notes, we will introduce Asymptotics, then we will give a short glimpse on Perturbation theory (regular versus singular), which plays a crucial role especially in theoretical physics. Our goal is to find Asymptotic series that approximates the values of integrals depending on some parameter or the solutions of differential equations. These methods that lead to obtain more effective algorithms of numerical evaluation are called: Asymptotic Methods.

This work focuses on the bifurcation behavior before chaos phenomenon happens. Traditional numerical method is unable to solve the unstable limit cycle of nonlinear system. One algorithm is introduced to solve the unstable one, which is based one of the continuation method is called DEPAR approach. Combined with analytic and numerical method, the two stable and symmetrical equilibrium solutions exist through Fork bifurcation and the unstable and symmetrical limit cycles exist through Hopf bifurcation of Lorenz system. With the continuation algorithm, the bifurcation behavior and its phase diagram is solved. The results demonstrate the unstable periodical solution is around the equilibrium solution, besides the trajectory into the unstable area cannot escape but only converge to the equilibrium solution.

60\% of the global population is expected to be in cities by 2050. At the same time the climate is changing at an accelerated rate. In this short paper we discuss the conflation of these two phenomena and how it may change the cities of the future. We formulate this as an optimization problem that could help answer important questions such as where are they likely to be located? How are they to be powered? What would be their demand for mobility and how might this be met? How over or under ground might these cities be? This paper first looks at a historical paradigm of cities in the absence of the climate crisis and then proposes the new paradigm to look at cities of the future faced by the challenge of the climate change crisis.

This is the first study to provide a systematic monetary benefit matrix, including greenhouse gas (GHG) emissions reduction benefits and air pollution reduction health co-benefits, for a change in on-the-road transport to low-carbon types. The benefit transfer method is employed to estimate the social cost of carbon and the health co-benefits via impact pathway analysis in Taiwan. Specifically, the total emissions reduction benefits from changing all internal combustion vehicles to either hybrid electric vehicles, plug-in hybrid electric vehicles, or electric vehicles would generate an average of US$760 million from GHG emissions reduction and US$2,091 million from health co-benefits based on air pollution reduction, for a total benefit of US$2,851 million annually. For a change from combustion scooters to light- or heavy-duty electric scooters, the average GHG emissions reduction benefits would be US$96.02 million, and the health co-benefits from air pollution reduction would be US$1,008.83 million, for total benefits of US$1,104.85 million annually.

This paper proposes a new structure of the dual-rotor hybrid-excited axial-flux permanent magnet vernier machine (DR-HEAFPMVM) with the modular stator and the consequent-pole PM (CPM) rotor for low-speed, high torque density applications such as in-wheel electric vehicles. The tooth-wound non-overlapping armature windings and direct current (DC) excitation windings are respectively arranged in stator main-teeth and split-teeth to obtain the modulated and adjustable air-gap flux densities, which result in the high torque density and outstanding flux-weakening capability. First, the design consideration, operation principle, and the air-gap flux density distributions of the proposed machine are elaborated based on the air-gap permeance function. Then, the influence of the pole ratios (PRs) and the DC excitation currents on the main electromagnetic performances of the DR-HEAFPMVM, such as the flux-weakening capability, back-electromotive force (back-EMF), on-load electromagnetic torque, loss distribution, and efficiencies, is investigated using the 3-D finite-element method (FEM). Results verify the feasibility of the flux adjustment of the DC excitation windings equipped in the split-tooth, and the design with a pole ratio of 8/1 tends to have higher torque density, higher machine efficiency, and considerable flux-weakening capability compared with the other two PRs.

This study investigates effective strategies for second language education in primary schools, analyzing the efficacy of immersive and interactive methods, digital literacy tools, and mixed-method approaches. The findings reveal significant improvements in language proficiency and student engagement through these methodologies, with immersive and interactive strategies showing substantial benefits in oral proficiency and engagement, digital tools enhancing accessibility and engagement, and mixed-method approaches yielding the highest overall effectiveness. The study underscores the importance of a balanced, flexible approach to language education, integrating traditional and modern methods to cater to diverse learner needs. These strategies not only advance linguistic skills but also contribute to the broader cognitive and emotional development of young learners, emphasizing the critical role of effective language education in preparing students for a globalized world.

The analytical method for the calculation of the properties of a bolted connection established by the structural Eurocodes proposes the T-stub as a component for the characterization of the tension and compression zones in moment joints. In this article, a review of the state of the art on the T-stub component is developed, where the works developed since it was initially defined, and from the perspectives of formulation, experimentation and numerical simulation are summarized and discussed. Additionally, possible future lines of work are proposed.

The aim of the research was a comprehensive evaluation of concrete using the EIPI method. In the evaluation the compressive strength of concrete and its durability properties represented by sorptivity and air permeability were taken into account. Since copper slag waste with increased natural radioactivity was used in the assessed concrete, additional evaluation was carried out taking into account the influence of natural radioactivity within the performance index. Also the reference concrete, which was made without the use of copper slag waste, was evaluated for comparative purposes. In order to make the evaluation as comprehensive as possible, the concrete made with the use of three types of cement was subjected to the assessment: CEM I, CEM II and CEM III. The results show that in both approaches the best result was achieved by concrete with CEM III cement. If natural radioactivity is not taken into account in the evaluation, the best result is obtained by concrete made with copper slag waste, and if radioactivity is considered, the best result is obtained with concrete without addition of the waste. It follows from the above that although natural radioactivity has a significant impact on the EIPI evaluation result, the decisive factor is still the type of cement.

In this research paper, change detection based methods were considered to find collapsed and intact buildings using radar remote sensing data or radar imageries. Main task of this research paper is collection of most relevant scientific research in field of building damage assessment using radar remote sensing data. Several methods are selected and presented as best methods in present time, there are methods with using interferometric coherence, backscattering coefficients in different spatial resolution. In conclusion, methods are given in end, which show, which methods and radar remote sensing data give more accuracy and more available for building damage assessment. Low resolution Sentinel-1A/B radar remote sensing data are recomended as free available for monitoring of destruction degree in microdistrict level. Change detection and texture based method are used together to increase overall accuracy. Homogeneity and Dissimilarity GLCM texture parameters found as better for separation of a collapsed and intact buildings. Dual polarization (VV,VH) backscattering coefficients and coherence coefficients (before earthquake and coseismic) were fully utilized for this study. There were defined the better multi variable for supervised classification of none building, damaged and intact buildings features in urban areas. In this work, we were achieved overall accuracy 0.77, producer’s accuracy for none building is 0.84, for damaged building case 0.85, for intact building 0.64. Amatrice town was chosen as most damaged from 2016 Central Italy Earthquake.

In this paper, we proposed the numerical method called the variational iteration orthogonal collocation method (VIOCM), for the approximate solution of the deadly Corona virus model using Mamadu-Njoseh polynomials as basis functions. The proposed method is an elegant mixture of the variational iteration method (VIM) and the orthogonal collocation method (OCM). It was observed that the proposed method converges rapidly to the exact solution even as N increases. This suggests that the use of orthogonal polynomials as trial functions for the SEIR model is indeed an effective approximant as it produces the analytic solution at just few iterations. Resulting numerical evidences were compared with the standard variational iteration method as available in literature. All computational frameworks were executed with MAPLE software.

The study aimed to manage and to analyse the results of the laboratory tests, routinallypractice for hepatitis C diagnosis, using blood tests. Statistical analysis of this study results, was performed using the laboratory informatic system. The results of the study are substantial and intricate reffering to comparision between two methods concretlly ELISA method (Enzyme-Linked Immunosorbent Assay) and chemiluminescence methods and their results. Good to know our opinion that RT-PCR technique, it is considered proper for the diagnosis of HCV ( Hepatitis C virus).

Circulating atypical cells (CAC) are released from a primary tumour site into peripheral blood and are indicators of cancer metastasis. CAC occur at very low frequency in circulating blood, and their detection remains challenging. Moreover, white blood cells (WBC) are the major contaminant in enriched CAC samples. Here, we developed matrix-assisted laser desorption ionization–time of flight mass spectrometry (MALDI-TOF MS) as a novel CAC characterization platform. Main spectra profiles (MSP) of normal and cancer cells were generated by MALDI-TOF MS, and a cell-main spectra database was then compiled and analysed using the MALDI Biotyper software. Logarithmic scores accurately predicted distinct cell types. The feasibility of this workflow was then validated using simulated samples, which were prepared by 5,000 WBC of three healthy individuals spiked with varying numbers (3, 6, 12, 25, 50 and 100) of lung, colon, or prostate cancer cells. MALDI-TOF MS was able to detect cancer cells down to six cells over the background noise of 5,000 WBC with significantly higher predictive scores as compared to WBC alone. Further development of cell-MSP database to cover all cancer types sourced from cell lines and patient tumours may enable the use of MALDI-TOF MS as a cancer-screening platform in clinical settings in the future.

In this paper, the Shannon entropy measure was used to assess changes in precipitation and temperature conditions. Due to the short, low-volume sequences of precipitation and temperature data analysed, a bootstrap method was used in the procedure for calculating Shannon entropy. The analysis used minimum and maximum values of monthly precipitation totals and monthly mean temperatures for 377 catchments distributed across the globe. A 110-year data series from 1901 to 2010 was analysed. Entropy values for the estimated parameters of the generalised extreme value distribution (GEV) were calculated for the adopted data. Entropy value calculations were performed for the left-hand constraint, based on minimum values, and for the right-hand constraint, based on maximum values. The applicability of Shannon's entropy measure in the analysis of climate change was demonstrated by allowing the degree of disorder and complexity of the distributions describing climate variables in the form of precipitation and temperature to be measured. This made it possible to obtain information on the directions of changes occurring with regard to minimum and maximum values in the field of monthly precipitation and mean temperatures in the analysed catchments. The study demonstrated the existence of Shannon entropy trends. The evaluation of entropy trends for precipitation and temperature sequences was performed using non-parametric tests. Mann -Kendall tests at the 5% significance level were used for trend analyses. The Pettitt test was performed to determine the point of change in trend for the rainfall and temperature data. The performed analysis was supported by graphical presentations.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

The traditional bored pile technology has some arduous problems, such as the sediment at the pile tip, the mud skin along the pile shaft, and the stress release due to borehole construction. The post-grouted technology at the pile tip of bored pile has emerged because of demand. The grouting migration height (GMH) is of great significance to the strengthen and reinforcement of the pile foundation. This paper derives the calculation formula of the GMH based on the theory of the column hole expansion and Herschel-Bulkley model. The influence of relevant parameters on the GMH is discussed. Aiming at the problem of the grouting migration along the pile shaft in layered soils, the iterative calculation method of the GMH is proposed. The correctness of the GMH is verified by an engineering case, which can guide the engineering practice. The result shows that the GMH increases with the increase of the grouting pressure, the pile diameter and the thickness of the mud skin, and the grouting pressure is positively correlated with the GMH. The GMH decreases with the increase of the buried depth, the consistency coefficient and the rheological index. On this basis, the correctness of the GMH is verified by an engineering case.