This article is devoted to the issues of thermal softening of materials in the surface layer of forging tools. The research covers numerical modeling of the forging process, laboratory tests of tempering of nitrided layers and the analysis of tempering of the surface layer of tools in the actual forging process. Numerical modeling was supported by measuring the temperature inside the tools with a thermocouple inserted into the tool to measure the temperature as close to the surface as possible. The modeling results confirmed the possibility of tempering the die material. The results of laboratory tests made it possible to determine the influence of temperature on tempering at different surface layer depths. Numerical analysis and measurement of surface layer microhardness of tools revealed the destructive effect of temperature during forging on the tempering of the nitrided layer and on the material layers located deeper below the nitrided layer.

Climate change and rapid urbanization are adversely affecting the urban environment by exacerbating the widely reported Urban Heat Island effect in Dhaka, Bangladesh. Two wetland areas with variable riparian shadings in the warm-humid conditions of urban Dhaka had been investigated through field campaigns on microclimatic parameters for their cooling potential on the surrounding urban fabric. It was observed that an inversion layer of fully saturated air develops over the water surface of wetland, suppressing evaporation from the wetland water surface layer, which was effectively reducing the heat exchange between the water surface and the air layer above it through its action as an insulating vapor blanket. Because of this effect, the wetland was unable to render as a source of coolth for the surrounding overheated urban area. This effect of the inversion layer was more pronounced in the urban wetland without riparian shading either by urban form or tree canopy. A Multiphysics simulation study conducted on the selected urban wetlands indicates the effect of differential shading pattern on the relation between fetch and inversion layer thickness. This research hypothesizes that the wetland can act as an urban adaption measure against the urban heat island effect by potentially transforming them into Urban Cooling Island (UCI) towards a favorable urban bioclimate.

This paper presents a study aimed at enhancing the performance of quantum dot light-emitting didoes (QLEDs) by employing a solution-processed molybdenum oxide (MoO3) nanoparticle (NP) as a hole injection layer (HIL). The study investigates the impact of varying the concentrations of the MoO3 NP layer on device characteristics and explores the underlying mechanisms responsible for the observed enhancements. Experimental techniques such as an X-ray diffraction and field-emission transmission electron microscopy were employed to confirm the formation of MoO3 NPs during the synthesis process. Ultraviolet photoelectron spectroscopy is employed to analyze the electron structure of the QLEDs. The QLED with an 8 mg/mL concentration of MoO3 nanoparticles achieves remarkable improvements in device performance, with a maximum luminance of 69,240.7 cd/cm2, maximum current efficiency of 56.0 cd/A, and maximum external quantum efficiency (EQE) of 13.2%. The obtained results signify a notable progress in comparison to QLED without HIL and those utilizing the widely used poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) HIL. They exhibit a remarkable enhancement of 59.5% and 26.4% in maximum current efficiency, respectively, as well as a significant improvement of 42.7% and 20.0% in maximum EQE, respectively. This study opens up new possibilities for the selection of HIL and the fabrication of solution-processed QLEDs, contributing to the potential commercialization of these devices in the future.

A field theoretic representation of the classical partition function is derived for a system composed of a mixture of anisotropic and isotropic mobile charges that interact via long range Coulomb and short range nematic interactions. The field theory is then solved on a saddle-point approximation level, leading to a coupled system of Poisson-Boltzmann and Maier-Saupe equations. Explicit solutions are finally obtained for a calamitic counterion-only system in proximity of a charged planar wall. The nematic order parameter profile, the counterion density profile and the electrostatic potential profile are interpreted within the framework of a nematic-isotropic wetting phase with a Donnan potential difference.

The perovskite solar cells (PSCs) have been significantly improved by utilizing inorganic hole transporting layer (HTL), such as nickel oxide. Despite the promising properties, there are still limitations due to defects. Recently, research on self-assembled monolayers (SAM) is being actively conducted, which show promise in reducing defects and enhancing device performance. In this study, we successfully engineered a p-i-n perovskite solar cell structure utilizing HC-A1 and HC-A4 molecules. These SAM molecules were found to enhance the grain morphology and uniformity of the perovskite film, which are critical factors in determining optical properties and device performance. Notably, HC-A4 demonstrated superior performance due to its distinct hydrophilic properties with a contact angle of 50.3°, attributable to its unique functional groups. Overall, the HC-A4 applied film exhibited efficient carrier extraction properties, attaining a carrier lifetime of 117.33 ns. Furthermore, HC-A4 contributed the superior device performance with its favorable band alignment, achieving the highest device efficiency of 20%.

The Chebyshev collocation method (ChC) implemented as Chebfun is used in order to solve a class of second order one-dimensional singular and genuinely nonlinear boundary value problems. Efforts to solve these problems with conventional ChC have generally failed, and the outcomes obtained by finite differences or finite elements are seldom satisfactory. We try to fix this situation using the new Chebfun programming environment. However, for toughest problems we have to loosen the default Chebfun tolerance in Newton's solver as the ChC runs into trouble with ill-conditioning of the spectral differentiation matrices. Although in such cases the convergence is not quadratic the Newton updates decrease monotonically. This fact, along with the decreasing behaviour of Chebyshev coefficients of solutions, suggests that the outcomes are trustworthy, i.e., the collocation method has exponential (geometric) rate of convergence or at least an algebraic rate. We consider first a set of problems that have exact solutions or prime integrals and then another set of benchmark problems that do not possess these properties. Actually, for each test problem carried out we have determined how Chebfun solution converges, its length, the accuracy of the Newton method and especially how well the numerical results overlap with the analytical ones (existence and uniqueness).

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

Considerable efforts have been made in recent years to identify an optimal treatment method for the removal of antibiotics from wastewaters. A series of supramolecular organic-inorganic magnetic composites containing Zn-modified MgAl LDHs and Cu-phthalocyanine as photosensitizer have been prepared with the scope to β-lactam antibiotics removal from aqueous solutions. The characterization of these materials confirmed the anchorage of Cu-phthalocyanine onto the edges of the LDH lamellae, with a negligible part inserted in the interlayer space. The removal of β-lactam antibiotics occurred via a concerted adsorption and photocatalytic degradation. The efficiency of the composites was depending on i) the LDH: magnetic nanoparticle (MP) ratio, that is strongly correlated to the textural properties of the catalysts, and ii) the phthalocyanine loading in the final composite. A maximum of the efficiency was achieved with a removal of ~93% of antibiotics after 2h of reaction.

Hf1-xZrxO2 (HZO) thin films are versatile materials suitable for advanced ferroelectric semiconductor devices. Previous studies have shown that the ferroelectricity of HZO thin films, can be stabilized by doping them with group III elements at low concentrations. While doping with Y improves the ferroelectric properties, there has been limited research on Y-HZO thin films fabricated using atomic layer deposition (ALD). In this study, we investigated the effects of Y doping cycles on the ferroelectric and electrical properties of as-deposited Y-HZO thin films with vaying compositions fabricated through ALD. The Y-HZO thin films were stably crystallized without the need for post-thermal treatment and exhibited transition behavior depending on the Y-doping cycle and initial composition ratio of the HZO thin films. These Y-HZO thin films offer several advantages, including enhanced dielectric constant, leakage current density, and improved endurance. Moreover, the optimized Y-doping cycle induced a phase transformation that resulted in Y-HZO thin films with improved ferroelectric properties, exhibiting stable behavior without fatigue for up to 1010 cycles. These as-deposited Y-HZO thin films show promise for applications in semiconductor devices that require high ferroelectric properties, excellent electrical properties, and reliable performance with a low thermal budget.

Reducing the amount of precipitation in summer in the Chernozems area alters soil organic matter (SOM). To compensate for the lack of moisture, farmers are introducing new agricultural technologies such as no-till cultivation. In turn, no-till practices influence the composition of SOM. We examined the impacts of the rise of aridity and no-till technology on the chemical composition of bioavailable and recalcitrant pools of OM. The properties of SOM were assessed using double-shot pyrolysis with gas chromatography/mass spectrometry (GC/MS). The thermolabile substances that are volatilised in the first stage of pyrolysis (300°C) are considered the bioavailable pool. Accordingly, substances are obtained in the second pyrolysis stage (500°C) were attributed to the recalcitrant pool. Identified in both steps of pyrolysis, products were assigned to different chemical groups (lignin-derivative, polysaccharide-fragments, indoles, etc.) and relative abundances were calculated. In work for the separation of substances, a polar column was used for chromatography of the thermolabile fraction. With an increase in aridity in Сhernozems, the content in the bioavailable pool of polysaccharide fragments decreased and the proportion of indoles increased. In the recalcitrant pool, the abundance of six-membered rings with nitrogen and aromatic compounds decreases at the same time the contents of unsubstituted and O-substituted acyclic compounds as well as pyridine increases. The influence of the NT was more noticeable in the recalcitrant OM. The NT practice promotes biological activity and to rich in nitrogen compounds the bioavailable OM; this process contributes to the accumulation of carbon in the recalcitrant OM.

We have suggested earlier a new sustainable method for permafrost thermal stabilization that combines passive screening of solar radiation and precipitation with active solar-powered cooling of the near-surface soil layer thus preventing heat penetration in depth. Feasibility of this method has been shown by calculations, but needed experimental proof. In this article, we are presenting the results of soil temperature measurements obtained at the experimental implementation of this method outside of the permafrost area which actually meant higher thermal loads than in Polar Regions. We have shown that near-surface soil layer is kept frozen during the whole summer, even at air temperatures exceeding +30°C. Therefore, the method has been experimentally proven to be capable of sustaining soil frozen even in more extreme conditions than expected in permafrost areas. In addition to usual building and structure thermal stabilization, the method could be used to prevent the development of thermokarst, gas emission craters, and landslides; greenhouse gases, chemical, and biological pollution from the upper thawing layers at least in the area of human activities; protection against coastal erosion; and permafrost restoration after wildfires. Using commercially widely available components, the technology can be scaled up for virtually any size objects.

The circular photogalvanic effect (CPGE) is the photocurrent generated in an optically active material in response to an applied ac electric field, and it changes sign depending on the chirality of the incident circularly polarized light. It is a non-linear dc current as it is second-order in the applied electric field, and for a certain range of low frequencies, takes on a quantized value proportional to the topological charge for a system which is a source of nonzero Berry flux. We show that for a non-interacting double-Weyl node, the CPGE is proportional to two quanta of Berry flux. On examining the effect of short-ranged Hubbard interactions upto first-order corrections, we find that this quantization is destroyed. This implies that unlike the quantum Hall effect in gapped phases or the chiral anomaly in field theories, the quantization of the CPGE in topological semimetals is not protected.

Wearing gloves while operating machinery in workshops is an essential precaution to prevent mechanical injuries and burns from high temperatures, among other potential hazards. Ensuring workers are properly equipped with gloves, which is a crucial measure in accident prevention. Glove images often occupy a minimal proportion of the frame and are easily obscured by cluttered backgrounds, especially with limited edge computing resources. Consequently, this study proposes a glove detection algorithm called YOLOv8-AFPN-M-C2f based on YOLOv8, offering swifter detection speeds, lower computational demands, and enhanced accuracy for workshop scenarios. This research innovates by substituting the head of YOLOv8 with the AFPN-M-C2f network, amplifying the pathways for feature vector propagation, and mitigating semantic discrepancies between non-adjacent feature layers. Additionally, the introduction of a superficial feature layer enriches surface feature information, augmenting the model's sensitivity to smaller objects. To assess the performance of the YOLOv8-AFPN-M-C2f model, we conducted multiple experiments using a factory glove detection dataset compiled for this study. The results indicate that the enhanced YOLOv8 model surpasses other network models. Compared to the baseline YOLOv8 model, the refined version shows a 2.6% increase in mAP@50%, a 90.1% rise in FPS, and a 13% reduction in the number of parameters. This research contributes an effective solution for the detection of glove adherence.

Based on the definition of double fuzzy relations, two types of new rough set models are constructed, which are multi-granulation double fuzzy rough sets called optimistic and pessimistic multi-granulation double fuzzy rough sets, and some of their properties were studied. In addition, we study the relationship between optimistic and pessimistic multi-granulation double fuzzy rough sets and double fuzzy rough sets.

Lead halide perovskite has become a promising candidate for high-performance photodetector (PD) applications due to its attractive optical and electrical properties such as high optical absorption coefficient, high carrier mobility, and long carrier diffusion length. However, the presence of highly toxic lead in these devices has limited their practical applications and even hindered their progress toward commercialization. Therefore, the scientific community has been committed to searching for low-toxic and stable perovskite-type alternative materials. Lead-free double perovskite materials, which are still in the preliminary stage of exploration, have achieved inspiring results in recent years. In this review, we mainly focused on two types of lead-free double perovskite based on different Pb substitution strategies, including A2M(I)M(Ⅲ)X6 and A2M(IV)X6. We reviewed the research progress and prospects of lead-free double perovskite photodetectors in the past three years. And more importantly, from the perspective of optimizing inherent defects in materials and improving device performance, we proposed some feasible pathways and made an encouraging perspective for the future development of lead-free double perovskite photodetectors.

The materials used as corrosion inhibitors are [Zn-Al-Cl], [Mg-Al-Cl], [Ni-Fe-Cl], and [Co-Fe-Cl] layered double hydroxides (LDHs). They were synthesized by coprecipitation and characterized by X-ray diffraction (XRD), Fourier transforms infrared spectroscopy (FTIR), and thermal anal-yses. The efficiency of these corrosion inhibitors on mild steel in concentrated hydrochloric acid (18.5%) at 60°C (chemical pickling conditions of steel) was studied using electrochemical and gravimetric methods for different concentrations. The surface morphology and composition were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS), respectively. The inhibitory efficiency in the case of 1.2 g.L-1 LDH was found to be 83.33%, 83.65%, 68.38%, and 74.73% for [Ni- Fe-Cl], [Zn-Al-Cl], [Co-Fe-Cl], and [Mg-Al-Cl], respectively.

Environmental and occupational exposure to hexavalent chromium, Cr(VI), causes female reproductive failures and infertility. Cr(VI) is used in more than 50 industries and is a group-A carcinogen, mutagenic and teratogenic, and a male and female reproductive toxicant. Our previous findings indicate that Cr(VI) causes follicular atresia, trophoblast cell apoptosis, and mitochondrial dysfunction in metaphase II (MII) oocytes. However, the integrated molecular mechanism of Cr(VI)-induced oocyte defects are not understood. The current study investigates the mechanism of Cr(VI) in causing meiotic disruption of MII oocytes, leading to infertility in superovulated rats. Postnatal day (PND)-22 rats were treated with potassium dichromate (1 and 5 ppm) in drinking water from PND 22-29 and superovulated. MII oocytes were analyzed by immunofluorescence, and images were captured by confocal microscopy and quantified by Image Pro Plus software. Our data showed that Cr(VI) increased microtubule misalignment, missegregation of chromosomes, a bulged and folded actin cap, oxidative DNA and protein damage, increased DNA double-strand break, and DNA repair protein RAD51. Cr(VI) also induced incomplete cytokinesis and delayed polar body extrusion. Our study indicates that exposure to environmentally relevant doses of Cr(VI) caused severe DNA damage, distorted oocyte cytoskeletal proteins, and caused oxidative DNA and protein damage leading to infertility.

In order to improve the operation performance of the multi-stage double-suction centrifugal pump and reduce the internal energy loss of the pump, this paper proposes a single-objective optimization design method based on non-hierarchical response surface model (RSM) and the multi-island genetic algorithm (MIGA). Nine parameters, such as the blade outlet width and blade wrap angle, were used as design variables, and the optimization objective was the efficiency under design conditions. In total, 149 sets of valid data were obtained under the latin hypercube sampling method (LHS), the corresponding thresholds were set for efficiency and head, and 99 sets of valid data were obtained. A cross-validation analysis of the sieved data was carried out based on non-hierarchical RSM, global optimization of the efficiency was carried out using MIGA, and numerical verification was carried out via CFD. The research results show that compared with hierarchical RSM, non-hierarchical RSM can approximate the nonlinear relationship between the objective function and the design variables with higher accuracy, and the model fitting R2 value was 0.919. The efficiency was improved by 3.717% after optimization. The overall prewhirl of the impeller inlet after optimization decreased, the internal speed of the volute significantly improved, the large-area vortex at the volute and the outlet pipe was eliminated, the impact loss at the volute separating tongue disappeared, and the overall hydraulic performance of the pump was improved. The total entropy output value of the optimized pump was reduced by 4.79 (W/K), mainly concentrated in the reduction in the entropy output value of the double volute, and the overall energy dissipation of the pump was reduced.

Minimal rotating thermodynamic systems are addressed. Particle m placed into the rotating symmetrical double-well potential (bowl), providing binary logical system is considered. The condition providing the transfer of the particle from one frictionless half-well to another, and in this way possibility to record 1 bit of information is derived. The procedure of recording turns out to be irreversible; it is impossible to return the particle to its initial state under rotation about the same axis. The same rotating double-well system exerted to the thermal noise is considered. Minimal rotating thermal engine built of the rotating chamber, movable partition and the particle confined within the chamber is treated. Rotation of the system displaces the partition; thus, enabling erasing of one bit information. Erasing of 1 bit of information is due to the inertia (centrifugal force) acting on the partition. Isothermal expansion of the “minimal gas” expectedly gives rise to the Landauer bound. Compression of the “gas” with the rotation around the same axis is impossible and demands the additional axis of rotation. The interrelation between the possibility of recording/erasing information and the symmetry of the system is considered.

Delayed atomic layer deposition (ALD) of ZnO, i.e., area selective (AS)-ALD, was successfully achieved on silicon wafers (Si/SiO2) terminated with tris(dimethylamino)methylsilane (TDMAMS). This resist molecule was deposited in a home-built, near atmospheric pressure, flow-through , gas-phase reactor. TDMAMS has been shown to react with Si/SiO2 in a single cycle/reaction and to drastically reduce the number of silanols that remain at the surface. ZnO was deposited in a commercial ALD system using dimethylzinc (DMZ) as the zinc precursor and H2O as the coreactant. Deposition of TDMAMS was confirmed by spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), and wetting. ALD of ZnO, including its selectivity on TDMAMS – terminated Si/SiO2 (Si/SiO2/TDMAMS), was confirmed by in situ ellipsometry, ex situ SE, XPS, and/or high sensitivity – low energy ion scattering (HS-LEIS). The thermal stability of the TDMAMS resist layer, which is an important parameter for AS-ALD, was investigated by heating Si/SiO2/TDMAMS in air and nitrogen at 330 ºC. ALD of ZnO takes place more readily on Si/SiO2/TDMAMS heated in the air than in N2, suggesting greater damage to the surface heated in the air. To better understand the in situ ALD of ZnO, the data were also plotted as the normalized growth per cycle and to show the selectivity. Even one, short pulse of TDMAMS effectively passivates Si/SiO2. TDMAMS can be an effective small molecule inhibitor of ALD of ZnO on Si/SiO2 surfaces.

RNA silencing serves key roles in a multitude of cellular processes, including development, stress responses, metabolism, and maintenance of genome integrity. Dicer, Argonaute (AGO), double-stranded RNA binding (DRB), RNA-dependent RNA polymerase (RDR) and DNA-dependent RNA polymerases known as Pol IV and Pol V form core components to trigger RNA silencing. Common bean (Phaseolus vulgaris) is an important staple crop worldwide. In this study, we aimed to unravel the components of the RNA-guided silencing pathway in this non-model plant taking advantage of the availability of two genome assemblies of Andean and Meso-American origin. We identified six PvDCLs, thirteen PvAGOs, 10 PvDRB, 5 PvRDR, in both genotypes, suggesting no recent gene amplification or deletion after the gene pool separation. In addition, we identified one PvNRPD1 and one PvNRPE1 encoding the largest subunits of Pol IV and Pol V, respectively. These genes were categorized into subgroups based on phylogenetic analyses. Comprehensive analyses of gene structure, genomic localization and similarity among these genes were performed. Their expression patterns were investigated by means of expression models in different organs using online data and quantitative RT-PCR after pathogen infection. Several of the candidate genes were up-regulated after infection with the fungus Colletotrichum lindemuthianum.

Alloys based on TiNi are widely used in various fields of technology and medicine. In the present work, we report on preparation of TiNi-alloy based wire with the shape memory effect, which was used for compression clips for surgery. Composition and structure of the wire, and its martensitic and physical-chemical properties were studied using SEM, TEM, optic microscopy, profilometry, mechanical tests, etc. The TiNi alloy was found to consist of B2 and B19' and secondary-phase particles of Ti2Ni, TiNi3 and Ti3Ni4. Its matrix was slightly enriched in Ni (50.3 at. % of Ni). Homogeneous grain structure was revealed (an average grain size of 19±0.3 μm) with equal quantities of grain boundaries of special and general types. Surface oxide layer provide improved biocompatibility and promote adhesion of protein molecules. Overall, the obtained TiNi wire was concluded to exhibit martensitic, physical and mechanical properties suitable for its use as an implant material. The wire was then used for manufacturing compression clips with the shape memory effect and applied in surgery. The medical experiment that involved 46 children demonstrated that the use of such clips in children with double-barreled enterostomies permitted to improve the results of surgical treatment.

Retinal findings may change in patients with obstructive sleep apnea syndrome (OSAS). The present study aims to evaluate several retinal findings such as macula layer thickness, peripapillary retinal nerve fiber layer, and the optic nerve head in patients with OSAS using optical coherence tomography (OCT) and monitor the result of several types of treatment of OSAS with OCT. A prospective comparative study was designed. Patients were recruited at a Sleep Unit of a University Hospital and underwent comprehensive ophthalmological examinations. Following exclusion criteria, fifty-two patients with OSAS were finally included. Patients were examined by OCT twice: first, before treatment; secondly, after six months of treatment. In mild-moderate patients, where retinal swelling has been demonstrated, retinal thicknesses decreased [fovea (p=0.026), as well as inner ring macula (p=0.007), outer ring macula (p=0.015), and macular volume (p=0.015)]. In severe patients, where retinal atrophy had been observed, retinal thickness increased [fovea (p<0.001)]. No statistically significant differences in efficacy between treatments were demonstrated. In conclusion, OCT can evaluate the retina in patients with OSAS and help monitor results after treatment. In severe OSAS, retinal thickness increased six months after treatment.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

In this paper a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy is proposed. The functionality of this new technique we explored by detailed gas dynamic and Monte Carlo atom-trajectory simulations, which results are presented and discussed. The results of similar computer simulations for JetRIS setup (as a typical representative of the conventional nowadays in-gas-jet technique) are presented and discussed as well. The direct comparison of calculation results for proposed new technique with the conventional one shows that the double-nozzle technique has many advantages compared with that one used in the JetRIS setup at GSI for future high-resolution laser spectroscopic study of heaviest elements. To fully implement the proposed new technique to all existing (or under construction) setups for in-gas-jet laser resonance ionization spectroscopy, it will be enough just replace the used their supersonic nozzle by the miniature double-nozzle device described in the paper.

The fundamental challenge for the structural design of complicated shapes and lightweight structures such as Tensile Membrane Structures (TMS) is a reliable estimation of lateral loading such as wind load. Wind pressure coefficients can’t be correctly calculated by standards for a large range of intricate forms of structures. Computational Fluid Dynamics (CFD), a strong computational technique for evaluating wind pressure distribution on complicated geometry, can be used to determine wind-related parameters. The average wind related-distributions for the tensile membrane surface are validated with a few contributions from prior studies, which are important to validate with benchmarks in experimental wind tunnel experiments. For the double-curved surface, the results show good agreement between experimental tests and CFD simulations. In this study, CFD simulation was used to calculate the mean surface pressure coefficient (Cp) for generic shapes and tensile membrane forms using the steady Reynolds-Averaged Navier-Stokes (RANS) technique. Wind force coefficients and the effect of wind directions are also explored across a wide range of classical and tensile forms. The purpose of the current research is to look at the effect of wind assault angle on the Cp distribution for tensile membrane structures and general shapes.

Hydrogels, soft materials with 3D polymer networks in aqueous solution, have been developed for engineering and bio-related fields. However, these conventional hydrogels are weak and brittle due to lack of energy dissipation mechanisms. Recently, dual-network hydrogels have been proposed, combining rigid and flexible networks and exhibiting high strength, stretchability, and toughness. This paper explores the rheological properties of dual-network hydrogels based on acrylamide and sodium alginate under large deformations. This dual network is a combination of a covalently crosslinked polyacrylamide network and a supramolecular crosslinked sodium alginate network at the presence of divalent calcium cations. Small and large amplitude oscillatory shear methods with Fourier transform rheology, stress decomposition method, and Chebyshev polynomial analysis of large amplitude oscillatory shear (LAOS) data were employed to evaluate non-linearity limit, toughness, and network rigidity. The concentration of calcium ions affects (concentrations 0-80 mg/ml) the nonlinear transition and limit points, and all gel samples exhibit strain hardening, shear thickening, and shear densification.

The famous Toms effect (1948) consists of a substantial increase of the critical Reynolds number when a small amount of soluble polymer is introduced into water. The most noticeable influence of polymer additives is manifested in the boundary layer near solid surfaces. The goal of the present paper is a group analysis of the boundary layer equations in two mathematical models of the flow of aqueous polymer solutions: the second grade fluid (Rivlin and Ericksen, 1955) and the model derived by Pavlovskii (1971). The equations of the unsteady two-dimensional boundary layer in the Pavlovskii and Rivlin-Ericksen models are analyzed for the first time here. These equations have no definite type so that finding their exact solutions is very important in order to understand the mathematical nature of the above mentioned models. The problem of group classification with respect to the arbitrary function of the longitudinal coordinate and time present in the equations, which sets the pressure gradient of the external flow, arises. All functions for which an extension of the admitted Lie group occurs are found. The task includes the ratio of two characteristic length scales. One of them is the Prandtl scale, and another is defined as the square root of the normalized coefficient of relaxation viscosity (Frolovskaya and Pukhnachev, 2018) and does not depend on the characteristics of the motion. The paper contains a number of exact solutions in the Pavlovskii model including a solution describing the flow near a critical point. Among the solutions of the new model of the boundary layer, a special place is taken by the solution of the stationary problem of flow around a rectilinear plate. Within the framework of the Prandtl theory of the boundary layer, such a solution was constructed by Blasius (1908). As is well-known, this solution has a non-removable defect: the transverse velocity near the edge of the plate increases without bound. The introduction of a relaxation term into the model makes it possible to eliminate this singularity.

We construct a microscopic model to study discrete randomness in bistable systems coupled to an environment comprising many degrees of freedom. A quartic double well is bilinearly coupled to a finite number N of harmonic oscillators. Solving the time-reversal invariant Hamiltonian equations of motion numerically, we show that for N=1, the system exhibits a transition with increasing coupling strength from integrable to chaotic motion, following the KAM scenario. Raising N to values of the order of 10 and higher, the dynamics crosses over to a quasi-relaxation, approaching either one of the stable equilibria at the two minima of the potential. We corroborate the irreversibility of this relaxation on other characteristic timescales of the system by recording the time dependences of autocorrelation, partial entropy, and the frequency of jumps between the wells as functions of N and other parameters. Preparing the central system in the unstable equilibrium at the top of the barrier and the bath in a random initial state drawn from a Gaussian distribution, symmetric under spatial reflection, we demonstrate that the decision whether to relax into the left or the right well is determined reproducibly by residual asymmetries in the initial positions and momenta of the bath oscillators. This result reconciles the randomness and spontaneous symmetry breaking of the asymptotic state with the conservation of entropy under canonical transformations and the manifest symmetry of potential and initial condition of the bistable system.

In the past decade, considerable efforts have been devoted to the development of semitransparent organic solar cells. Numerous materials and architectures have been proposed for the future commercialization of these devices. Among these, the use of ternary active layers demonstrated a great promise for the development of efficient semi-transparent organic solar cells with the potential for future applications including self-powered greenhouses and powered windows. Researchers seek alternative solutions to the trade-off between device power conversion efficiency (PCE) and average visible transmittance (AVT), with photoactive materials being the key parameters that govern both (PCE) and (AVT) as well as device stability. Several new organic materials, including polymers and small molecules, were synthesized, and used in conjunction with a variety of techniques to achieve semitransparent conditions. In this review paper, we will look at the working principle and key parameters of semi-transparent organic solar cells, as well as the methods that have been used to improve the performance of ternary-based semi-transparent organic solar cells. The main approaches were concluded to be spectral enhancement and transparency increment of the active layer through bandgap tuning, utilizing novel organic semiconductors, and design architecture of the active layers.

The stability issues in the widely known organic inorganic halide perovskite, CH3NH3PbI3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs2AgBiBr6 and Cs2TiBr6 is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide bandgap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, bandgap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

The goal of the manuscript is to design a relatively best control structure for the noise suppression of a drone’s camera gimbal action. The gimbal’s movement can be simplified as a rest-to-rest reorientation system that can achieve the boundary result of a dynamic system. Six different control architectures are proposed and evaluated based on their ability to control the trajectory of the dynamic-system position and speed, their running time, and quadratic cost. The robustness of the control architecture to uncertainties in inertia and sensor noise is also analyzed. Monte Carlo figures are used to assess the performance of the six control systems. The conditions for applying different architectures are identified through this analysis. The analysis and experimental tests reveal the most suitable control of the drone’s camera gimbal rotation.

The paper focuses on two unconventional magnetic field-based treatment regimes applied to an alloyed steel before applying a thermochemical treatment. This study was conducted in order to improve the behavior of the chosen material during the wear process. Increasing the wear resistance and the micro-hardness of the superficial layer obtained from the treatments are a priority, as well as improving the mechanical properties of a Cr-Mo alloyed steel. Thermomagnetic treatment, applied before plasma nitriding treatment, improves the mechanical properties of the base material, especially in the case of a steel with a considerable chromium content (1,02%). This paper is a review of my own researches in the last years.

Abstract The relationship between cancer and neurodegeneration has spurred extensive scientific discourse, challenging their historical classification as distinct disorders. While cancer signifies uncontrolled cellular proliferation and neurodegeneration marks progressive neuronal loss, recent insights highlight intriguing interconnections between these seemingly disparate conditions. Cancer entails perpetual signaling for growth, evasion of growth inhibitors, resistance to cell death, acquisition of replicative immortality, stimulation of blood vessel growth (angiogenesis), and initiation of invasion and metastasis. Conversely, investigations emphasize disrupted cellular energy regulation and evasion of immune surveillance as key traits arising from genome instability, mutations, and inflammation driving tumorigenesis. Neurodegeneration involves neuronal malfunction and depletion, synaptic impairment, and protein abnormalities aggregations contributing to muscle atrophy and cognitive deficits. Varied clinical studies underscore contrasting correlations between cancer and neurodegeneration, hinting at mirrored molecular pathways that foster cell resilience or vulnerability. Research explores cellular signaling in tumorigenesis, shared with neurodegenerative disorders. Aberrant expression or mutations in crucial genes implicated in neurodegeneration also surface in cancer contexts. Debates persist on the nature of the relationship between cancer and neurodegeneration, contemplating inverse associations or shared pathways. Understanding their complex interplay, encompassing genetics, cellular mechanisms, and environmental influences, remains pivotal in unraveling their connections. This review explores the intriguing perspective that neurodegeneration and cancer might share fundamental genetic links, delving into potential implications for their onset and progression.

The boundary layer height (BLH) distinguishes the interface between the lower and free atmosphere, which is a key variable in numerical simulation, aerosol, and environmental pollution studies. Thus, the goal of this work is to propose a novel method conjuncting with numerical regularization to analyze climate characteristics of the marine boundary layer height (MBLH) using 2007-2011 GPS-RO data from the COSMIC mission. While traditionally, the difference method has been used to achieve this aim, herein, we propose an innovative method, in which the bending angle profile gradient was calculated using the numerical regulation method where the regulation parameters are determined by the double-parameter model function method. Then, the MBLH was determined by employing the maximum gradient method to ascertain the height corresponding to the smallest gradient. The results show a correlation between currents and the MBLH—a relationship that has not been previously demonstrated. A low MBLH is associated with seasons and regions where cold ocean currents are prevailing; whereas a high MBLH is observed in the seasons and places where warm currents are prevailing. This correlation was validated by comparing the obtained results with different occultation data—i.e., atmprf and echprf—which also established that atmprf is more sensitive to convective cloud top capture. In seas with active convection, the armprf calculated bending angle is higher than that from echprf. Subsequently, the standard deviation was used to express the MBLH confidence level. The results show that the MBLH standard deviation is highest in low latitudes and lowest in the middle and high latitudes. Furthermore, we analyzed the interannual MBLH variation trend, which displayed a seasonal variation and spatial distribution corresponding with the current and subsolar point. Finally, we conducted a case study in the South China Sea, and identified a distinctive seasonal change and downward trend.

The results of studying the effect of particles of few-layer graphene (FLG) synthesized by self-propagating high-temperature synthesis (SHS) on the complex of strength and thermo physical properties of polymer composite products obtained by DLP 3D printing are presented. It has been discovered to achieve an increase in thermo physical and strength parameters of polymers modified by FLG compared with samples made on the unmodified base resin. This result was achieved due to low defectiveness, namely the absence of Stone-Wales defects in the structure of FLG due to the homogeneous distribution of FLG over the volume of the polymer in the form of highly dispersed aggregates. It was possible to increase hardness by 120 %, bending strength by 102 %, Charpy impact strength by 205 %, and thermal conductivity at 25 °C by 572 % at concentrations of few-layer graphene of no more than 2 wt. %.

In recent years, the need to make the built environment more resilient and adaptable to climate change has become increasingly evident. In Europe, this aspect concerns the vast majority of existing buildings, which present several deficiencies from the energy-efficiency point of view, considering they were designed before the introduction of modern energy codes. Nowadays, it is possible to retrofit existing buildings using advanced and high-efficient technologies such as Double Skin Façades (DSFs). The research aims to evaluate the use of properly designed DSFs for the energy restoration of existing buildings. In detail, various DSF configurations are applied to a residential building located in central Italy and investigated under present and future climate conditions, estimated through regional climate models. The results underline that all the analysed Double Skin Façades confirm to be a useful option, and, in particular, the Multi-Storey typology allows drastic energy needs decrement. Moreover, the general increase in temperatures and solar radiations could affect the building energy performance, and the insertion of DSF can mitigate the climate change effects, reducing the predicted energy consumption and ensuring better behaviours than the building in its original state.

Laser direct writing allows for the fabrication of complex structures, which is particularly advantageous in micro-optic applications. However, the increasing demand for optics quality requires the lowest optical power loss, which can occur from unwanted reflections. This research demonstrates the possibility of forming an anti-reflective coating on hybrid-polymer micro-lenses fabricated by employing laser direct writing (LDW), without changing their geometry. Such coating deposited by atomic layer deposition (ALD) decreased the reflection from 3.3 % to 0.1 % at the wavelength of 633 nm for one surface of SZ2080™.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

Nano- and micro-sized CeO2 surface layers based on titanium alloy TiAl6V4 were obtained by magnetron sputtering with or without subsequent annealing. The structure of the samples was determined using scanning electron microscopy, Auger electron spectroscopy, energy dispersive spectroscopy, and X-ray diffraction. Hardness was measured by sclerometry. A direct linear dependence of the thickness of the surface layers on the deposition time and an extreme dependence, passing through a maximum, on the power are shown. A decrease in hardness with an increase in the thickness of the cerium oxide coating was noted. An increase in surface roughness, delamination and loosening of the surface layer, presumably associated with annealing, were noted. In samples with a surface layer thinner than 715 nm without annealing and 750 nm after annealing, the formation of a sublayer of TiO2, Al2O3, and Ce(VO4) was found, and in annealed samples with a layer length of less than 300 nm, all cerium dioxide reacted with vanadium dioxide to form vanadate.

The extent of single and multi-cropping systems in any region, and potential changes to it, have consequences on food and resource use raising important policy questions. However, addressing these questions is limited by a lack of reliable data on multi-cropping practices at a high spatial resolution, especially in areas with high crop diversity. In this paper, we describe a relatively low-cost and scalable method to identify double cropping at the field-scale using satellite (Landsat) imagery. The process combines machine learning methods with expert labeling. We demonstrate the process by measuring double cropping extent in a portion of Washington State in the Pacific Northwest United States--- a region with significant production of more than 60 distinct types of crops including hay, fruits, vegetables, and grains in irrigated settings. Our results indicate that the current state-of-the-art methods for identifying cropping intensity---that apply rule-based thresholds on vegetation indices---do not work well in regions with high-crop-diversity. Our deep learning model was able to capture the diverse nuances and achieve a high accuracy (99\% overall accuracy and 0.92 Kappa coefficient). Our expert labeling process worked well and has potential as a relatively low-cost, scalable approach for remote sensing applications. The product developed here is valuable to inform several policy questions related to food production and resource use.

Building deep learning models proposed by third parties can become a simple task when specialized libraries are used. However, a great deal of mystery still surrounds the design of new models or the modification of existing ones. These tasks require in-depth knowledge of the different components or building blocks as well as their dimensions. This information is limited and broken up in different literature. In this article, we collect and explain in-depth the building blocks to design deep learning models, starting from the artificial neuron to the concepts involved in building deep neural networks. Furthermore, the implementation of each building block is exemplified using the Keras library.

A new three-dimensional numerical model of a polymer electrolyte fuel cell (PEFC) with a single straight channel has been developed to primarily investigate the important impact of the double-sided microporous layer (MPL) coating on the overall performance of the fuel cell and the distribution of the current and the oxygen concentration within the cathode gas diffusion layers (GDLs). Realistic experimentally estimated interfacial contact resistance values between the gas diffusion layer and each of the bipolar plates and the catalyst layer values were incorporated into the model, and parametric studies were performed. The results showed that the double-sided MPL coating could significantly improve the fuel cell performance by up to 30%. Also, it was shown that the neglect of the contact resistance between the MPL and the catalyst layer could overestimate the fuel cell performance by up to 6%. In addition, the results showed that the fuel cell performance and the distribution of the current and oxygen are more sensitive to the porosity of the MPL facing the bipolar plate than the porosity of the MPL facing the catalyst layer. All the above results are presented and critically discussed in detail.

Particles and photons appear to be total opposites; the former has rest mass which requires space to exist; the latter has kinetic energy which requires time to occur (oscillate). But they do share certain properties (e.g., quantization) that remain invariant when one is transformed (swapped) for the other. This gauge invariance is developed in some detail.The symmetry between particle and photon turns out to be one of inversion. It is the equalities of special relativity that support this inversion and the accompanying invariances: mass transformed to energy; space transformed to time. The great advantage of these symmetries (inversions) is that they provide guidance for an object little understood (the photon) based upon an object well understood (the particle). On this basis, progress can be made in the understanding of some long-standing issues: wave-particle duality, time’s arrow, the constant speed of light and nonlocality.

Perovskite solar cells have shown significant progress, but their commercialization remains hindered by lead-based toxicity. Many nontoxic perovskite-based solar cells have demonstrated potential such as Cs2AgBi0.75Sb0.25Br6, but their power-conversion efficiency is inadequate. To address this issue, some researchers are focusing on emerging acceptor-donor-acceptor'-donor-acceptor (A-DA'D-A) type non-fullerene acceptors (NFAs) for Cs2AgBi0.75Sb0.25Br6 to find effective electron transport layers for high-performance photovoltaic responses with low voltage drops. In this comparative study, four novel A-DA'D-A types NFAs such as BT-LIC, BT-BIC, BT-L4F, and were used as an electron transport layer (ETL) for the proposed devices, FTO/PEDOT: PSS/ Cs2AgBi0.75Sb0.25Br6/ETL/Au. Comprehensive simulations were conducted to optimize the devices. The simulations showed that all optimized devices exhibit photovoltaic responses, with the BT-BIC device having the highest power conversion efficiency (13.2%) and the BT-LIC device having the lowest (6.8%). The BT-BIC as ETL provides fewer interfacial traps and better band alignment, enabling greater open-circuit voltage for efficient photovoltaic responses.

Some cancer cells rely heavily on non-essential biomolecules for survival, growth, and proliferation. Enzyme based therapeutics can eliminate these biomolecules, thus specifically targeting neoplastic cells; however, enzyme therapeutics are susceptible to immune clearance, exhibit short half-lives, and require frequent administration. Encapsulation of therapeutic cargo within biocompatible and biodegradable poly(lactic-co-glycolic acid) nanoparticles (PLGA NPs) is a strategy for controlled release. Unfortunately, PLGA NPs exhibit burst release of cargo shortly after delivery or upon introduction to aqueous environments where they decompose via hydrolysis. Here we show the generation of hybrid silica-coated PLGA (SiLGA) NPs as viable drug delivery vehicles exhibiting sub-200 nm diameters, a metastable Zeta potential, and high loading efficiency and content. Compared to uncoated PLGA NPs, SiLGA NPs offer greater retention of enzymatic activity and slow the burst release of cargo. Thus, SiLGA encapsulation of therapeutic enzymes, such as asparaginase, could reduce frequency of administration, increase half-life, and improve efficacy for patients with a range of diseases.

In recent years, antibacterial coatings have become a significant approach in the global fight against bacterial pathogens. Developments in materials science, chemistry and biochemistry have led to a plethora of materials and chemical compounds that have potential for creating antibacterial coatings. Nonetheless, there has been insufficient consideration given to the analysis of the techniques and technologies used to apply these coatings. Among the various inorganic coating techniques, Atomic Layer Deposition (ALD) is noteworthy. It enables the successful synthesis of high-purity inorganic nanocoatings on surfaces of complex shape and topography, while also providing precise control over their thickness and composition. ALD has various industrial applications, but its practical application in medicine is still limited. In recent years, a substantial number of papers have been published on the suggested implementation of thin films and coatings produced through ALD in medicine, notably those with antibacterial properties. The aim of this paper is to carefully evaluate and analyse the relevant literature on this subject. Simple oxide coatings, including TiO2, ZnO, Fe2O3, MgO, and ZrO2, were examined, as well as coatings containing metal nanoparticles such as Ag, Cu, Pt, and Au, and mixed systems such as TiO2-ZnO, TiO2-ZrO2, ZnO-Al2O3, TiO2-Ag, and ZnO-Ag. Through comparative analysis, we have been able to draw conclusions on the effectiveness of various antibacterial coatings of different compositions, including key characteristics such as thickness, morphology, and crystal structure. ALD has been analysed in its use for developing antibacterial coatings for various applications. Furthermore, assumptions regarding the most promising development areas have been presented.

As the global aging trend continues to intensify, there will inevitably be more complex and diverse aging problems in the future. There is no doubt that designers have the responsibility to explore the possibilities of the future and solve the problems that will be faced in the future. Based on the Future Cone, the Double Diamond Model and the IDEO Method Cards, this study proposes a new model to guide the design practice of future aging issues in the context of aging. With the aim of validating and refining the framework, an ageing designer workshop was held where participants were asked to imagine, explore and express ideas about future ageing issues. The workshop was used to refine the proposed model. More specifically, the model includes a future concept, a design guidance process based on the Double Diamond Model, and tools that can be applied at all stages of design, which can help designers generate ideas and solutions for future aging problems, and collectively lead society to a more desirable future. Moreover, this study also explores broader directions for the development of the model and provides a reference for continued research on this topic in the future.

Initially introduced almost thirty years ago for the express purpose of providing electronic warfare systems the capabilities to detect, characterize, and identify radar emitters, Specific Emitter Identification (SEI) has recently received a lot of attention within the research community as a physical layer technique for securing Internet of Things (IoT) deployments. This attention is due in large part to SEI’s demonstrated success in passively and uniquely identifying wireless emitters using traditional machine learning and the success of Deep Learning (DL) within the natural language processing and computer vision areas. SEI exploits distinct and unintentional features present within an emitter’s transmitted signals. The existence of these distinctive and unintentional features is attributed to slight manufacturing and assembly variations that exist within and between the components, sub-systems, and systems that comprise an emitter’s Radio Frequency (RF) front end. Although sufficient to facilitate SEI, these features do not hinder normal operations such as detection, channel estimation, timing, and demodulation. However, despite the plethora of SEI publications, it has remained largely a focus of academic endeavors that primarily focus on proof-of-concept demonstration and little to no use in operational networks for various reasons. The focus of this survey is a review of SEI publications from the perspective of its use as a practical, effective, and usable IoT security mechanism, thus we use IoT requirements and constraints (e.g., wireless standard, nature of their deployment) as a lens through which each reviewed paper is analyzed. Previous surveys have not taken such an approach and have only used IoT as motivation, a setting, or a context. In this survey, we consider operating conditions, SEI threats, SEI at scale, publicly available data sets, and SEI considerations that are dictated by the fact that it is to be employed by IoT devices or IoT infrastructure.

This study provides, to our knowledge, the first detailed analysis of how surface oil modifies air-sea interaction in a two-way coupled model, i.e., the coupled-ocean-atmosphere-wave-sediment-transport (COAWST) model modified to account for oil-related changes to air-sea fluxes. This study investigates the effects of oil on surface roughness, surface wind, surface and near surface temperature differences, and boundary-layer stability, and how those conditions ultimately affect surface stress. We first conducted twin coupled modeling simulations with and without the influence of oil over the Deepwater Horizon (DWH) oil spill period (April 21 to May 5, 2010) in the Gulf of Mexico. Then we compared the results by using a modularized flux model with parameterizations selected to match those selected in the coupled model adapted to either ignore or account for different atmospheric/oceanic processes in calculating surface stress. When non-oil inputs to the bulk formula treated as unchanged by oil, the surface stress changes are always negative due to oil-related damping of surface roughness alone. However, the oil-related changes to 10-m wind speed and boundary-layer stability are found to play a dominant role in surface stress changes relative to those due to the oil-related surface roughness changes, highlighting that most of the changes in surface stress are due to the oil-related changes in wind speed and boundary-layer stability. Finally, the oil-related changes to surface stress due to the combined oil-related changes in surface roughness, surface wind, and boundary-layer stability are not large enough to have a major impact on the surface current and surface oil transport, indicating that the feedbacks from the surface oil to the surface oil movement itself are minor for forecasting the surface oil transport unless the fractional oil coverage is much larger than found in this study.

Titanium dioxide (TiO2) thin films have been widely used in transparent optoelectronic devices owing to their excellent optical properties also is used in photocatalysis, cosmetics, and many other biomedical applications. However, a lack of studies was published on microstructure and adherence comparison of the TiO2 deposited on both AISI substrates. In this work, TiO2 thin films were deposited onto AISI 304 and AISI 316L stainless steel (SS) substrates via atomic layer deposition. Its heterostructure, morphology, and adhesion were compared in both substrates looking for synergistic and multifunctional properties. Raman spectroscopy mapping and X-ray diffraction using the Rietveld refinement method showed that the films are composed of anatase and rutile phases in different percentages. Scratching tests were used to analyze the film adher-ence and friction between a diamond tip and TiO2 film, showing well adhered in both substrates.

RNA interference (RNAi) is one of the main mechanisms for disease resistance and small RNA production in plants. The main proteins involved in RNAi include Dicer-like (DCL), RNA-dependent RNA polymerase (RDR), double-stranded RNA-binding (DRB), and Argonaute (AGO). Juglandaceae contains a variety of important woody plants, and walnuts are one of the four major woody plant groups and one of the four major dried fruits in the world. To clarify the evolution and functional differentiation of RNAi-related proteins in the walnut (Juglans regia) genome, this study integrated various web resources from gene family acquisition to structural analysis and transcriptome data to correlate walnuts and their congeners. The walnut genome has 5 DCL, 13 RDR, 15 DRB and 15 AGO genes, similar genes encoding conserved protein structural domains and conserved motifs with similar subcellular localization. Walnut AGO proteins are classified into three classes and seven subclasses. The DCL is divided into four categories, while RDR is mainly divided into four categories, and DRB can be divided into six categories. The exception is that the copy number of walnut RDR1 is 9, in which seven RDR1 are distributed in clusters on chromosome 16. Purifying selection drove the formation of walnut genes, but protein classes were subjected to varying degrees of purifying selection. Additionally, these results showed some similarity in other plants of the walnut family. Moreover, different RNAi-related genes of walnut produced abundant selective expression in response to different tissues and stresses. In this study, DCL, RDR, DRB and AGO gene families were identified and analysed in the genome of the walnut family for the first time and preliminarily examined the evolution, structure and expression characteristics of these families to provide a preliminary basis for the evolution of the walnut RNAi pathway and breeding research.

This study estimates the effects of double long memory and structural breaks on the persistence level of six major cryptocurrency markets. We apply the Bai and Perron’s structural break test, Inclán and Tiao’s iterated cumulative sum of squares (ICSS) algorithm, and the fractionally integrated generalized autoregressive conditional heteroscedasticity (FIGARCH) model with different distributions. The results show that long memory and structural breaks characterize the conditional volatility of cryptocurrency markets and confirm our hypothesis that ignoring structural breaks leads to an underestimation of the persistence of volatility modelling. The ARFIMA-FIGARCH model with structural breaks and a skewed Student–t distribution fits the cryptocurrency market’s price dynamics well.

Membrane-based beverage dealcoholization is a successful process for producing low- and non-alcoholic beer and represents a fast-growing industry. Polyamide NF and RO membranes are commonly applied for this process. Polyelectrolyte multilayer (PEM) NF membranes are emerging as industrially relevant species and their unique properties (usually hollow fiber geometry, high and tunable selectivity, low fouling) underlines the importance of testing them in the food industry as well. To test PEM NF membranes for beer dealcoholization, at small pilot scale we dealcoholized filtered and unfiltered lager beer with the tightest available commercial polyelectrolyte multilayer NF membrane (NX Filtration dNF40), which has a MWCO=400Da which is quite high for these purposes. Dealcoholization is possible with a reasonable flux (10 LMH) at low pressures (5-8.6 bar) with a real extract loss of 16-18% and an alcohol passage of ~100%. Inorganic salt passage is high (which is typical for PEM NF membranes), which greatly affected beer flavor. During the dealcoholization process, the membrane underwent changes which substantially increased its salt rejection values (MgSO4 passage decreased 4-fold) while permeance loss was minimal (less than 10%). According to our sensory examination, the process yielded an acceptable flavored beer which could be greatly enhanced by the addition of the lost salts and glycerol.

We report the use of four-layer graphene (4LG) as a highly reliable transparent conductive electrode (TCE) for polymer-dispersed liquid crystal (PDLC)-based smart window devices. The adhesion between 4LG and the substrate was successfully improved through a water-induced interface-cleaning (WIIC) process. We compared the performance of a device with a WIIC-processed 4LG electrode with that of devices with a conventional Indium tin oxide (ITO) electrode and a 4LG electrode without a WIIC. With the application of the WIIC process, the PDLC smart window with a 4LG electrode exhibited reduced turn-on voltage and haze compared to 4LG without the WIIC process and characteristics comparable to those of the ITO electrode. Based on our observations, we conclude that 4LG with WIIC is a promising TCE for flexible smart windows.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

At present, nanomaterials (NMs) show extreme potential for a wide range of applications ranging from aerospace to energy storage applications owing to a number of properties which, in a number of contexts have been reported to be superior as compared to those of bulk counterparts. However, the high surface area to volume ratio which yields extraordinary properties to NMs also turns out to be the major limitation in a number of different contexts. For instance, the high surface area to volume ratio in these materials leads to a high reactivity, especially in electrochemical environments which are prevalent during energy storage applications. In this context, it is worthwhile mentioning that processing of NMs play a crucial role in influencing their mechanical properties. On the other hand, surface engineering has emerged as a powerful tool to deconvolute bulk properties from surface characteristics and has been reported to exhibit tremendous potential for overcoming the aforementioned limitation of NMs. The present review therefore, is aimed at highlighting the present status of research in the field of processing and applications of surface engineered NMs. Moreover, challenges and future perspectives in the aforementioned avenue have been discussed.

Fine-tuning is an important technique in transfer learning that has achieved significant success in tasks that lack training data. However, as it is difficult to extract effective features for single-source domain fine-tuning when the data distribution difference between the source and the target domain is large, we propose a transfer learning framework based on multi-source domain called adaptive multi-source domain collaborative fine-tuning to address this issue. This approach utilizes multiple source domain models for collaborative fine-tuning, thereby improving the model's feature extraction capability in the target task. Specifically, this approach employs an adaptive multi-source domain layer selection strategy to customize appropriate layer fine-tuning schemes for the target task among multiple source domain models. The objective is to extract more efficient features. Furthermore, a novel multi-source domain collaborative loss function is designed to facilitate the precise extraction of target data features by each source domain model. Simultaneously, it works towards minimizing the output difference among various source domain models, thereby enhancing the adaptability of the source domain model to the target data. In order to validate the effectiveness of the proposed the adaptive multi-source domain collaborative fine-tuning framework, it is analyzed and compared with the most widely used fine-tuning methods by applying them to seven publicly available visual categorization datasets commonly employed in transfer learning. Experimental results demonstrate that, in comparison with the existing fine-tuning approaches, our method not only enhances the accuracy of feature extraction in the model but also provides precise layer fine-tuning schemes for the target task, resulting in state-of-the-art performance.

In this study, multi-layer ceramic capacitors (MLCCs) detached from lighting sector's waste electrical-electronic equipment (WEEE) are characterised for the presence of rare earth elements (REEs) and precious metals (PMs). Their digestion was carried out with HNO3 & aqua regia on a heating plate and characterised with the use of inductively coupled plasma optical emission spectroscopy (ICP-OES) & scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The contents of REEs and PMs are 0.84 wt% and 0.60 wt%, respectively, and create an economic stored value in MLCCs that is essentially defined by PMs of 98.67% and by Pd 78.37%. The content of the main elements is: Nd 0.366 wt%, Y 0.220 wt%, Dy 0.131 wt%, Ag 0.467 wt%, and Pd 0.105 wt%. The results confirm the need of selective removal and separate recycling process of MLCCs from WEEE drivers.

Dendrite growth and parasitic reactions with liquid electrolyte are the two key factors that restrict the practical application of the lithium metal anode. Herein, a bis(benzene sulfonyl)imide based single-ion polymer artificial layer for lithium metal anode is successfully constructed, which is prepared via blending the as-prepared copolymer of lithiated 4, 4’-dicarboxyl bis(benzene sulfonyl)imide and 4,4’-diaminodiphenyl ether on the surface of lithium foil. This single-ion polymer artificial layer enables compact structure with unique continuous aggregated Li+ clusters, thus reducing the direct contact between lithium metal and electrolyte, and ensuring Li+ transport fast and homogeneous simultaneously. Based on which, the coulombic efficiency of the Li|Cu half-cell is effectively improved, and the cycle stability of the Li|Li symmetric cell can be prolonged from 160 h to 240 h. Surficial morphology and elemental valence analysis confirm that the bis(benzene sulfonyl)imide based single-ion polymer artificial layer effectively facilitates the Li+ uniform deposition and suppresses parasitic reactions between lithium metal anode and liquid electrolyte in the LFP|Li full-cell. This strategy provides a new perspective to achieve steady lithium metal anode, which can be a promising candidate in practical application.

In this study organic bulk heterojunction (BHJ) solar cell along with the spiro OMeTAD as a hole transport layer (HTL) and the PDINO as an electron transport layer (ETL) was simulated through the Solar Capacitance Simulator, one dimensional (SCAPS-1D) software to examine the performance of this type of polymer thin film organic solar cells. As an active layer the blend of polymer donor PBDB-T and non-fullerene acceptor ITIC-OE was used. Numerical simulation was performed by varying the thickness of HTL and active layer. Firstly, the HTL layer thickness was optimized to 50 nm, after that the active layer thickness varied up to 80 nm. These results of simulation demonstrated that the HTL thickness has rather little impact on efficiency while in the case of active layer thickness improves efficiency significantly. The temperature effect on the performance of solar cells was considered, by the simulation performed for temperature from 300 K up to 400 K and the efficiency of solar cell decreases with increasing temperature. Generally, polymer films usually are full of traps and defects, the density of defects (Nt) value was also introduced to the simulation, and it was confirmed that with the increasing of defect density (Nt), the efficiency of solar cell decreases. After thickness, temperature and defect density optimization, the reflection coating was also applied on it. It turned out that by introducing the reflection coating on the back side of solar cell, the efficiency increases by 2.5 %. Additionally, the positive effect of HTL and ETL doping on efficiency of this type of solar cells was demonstrated.

The crystal structure of quintinite, Mg4Al2(OH)12(CO3)·3H2O, from Jacupiranga alkaline complex (Cajati, São Paulo, Brazil) has been refined for two samples (91002 and C7029) using single-crystal X-ray diffraction data. The mineral crystallizes in the P-3c1 space group, a = 5.246/5.298, c = 15.110/15.199 Å for the samples 91002/C7029. The crystal structure consists of octahedral sheets with Mg and Al ordering according to the 3 × 3 superstructure. The Mg and Al atoms are coordinated by six hydroxylated oxygen atoms each with the average <Mg–O> and <Al–O> bond distances being in the ranges 2.022–2.053 Å and 1.974–1.978 Å, respectively. The interlayer structures are identical (in contradiction to the previous assumptions) and compose from disordered (CO3)2- groups and (H2O)0 molecules. The samples from Jacupiranga can be identified as quintinite-2T that is the second find of the polytype after the Kovdor alkaline complex (Kola peninsula, Russia). The powder X-ray diffraction pattern of quintinite-2T contains weak superstructure reflection at 4.57 Å (010) indicative of Mg and Al ordering. An important crystal-chemical criterion of quintinite is the interlayer distance (d00n-value) of ~ 7.56 Å, which is steady for natural specimens from various findings worldwide.

The thoracic surgery has increased drastically in recent years, especially in the light of the severe outbreak of 2019 novel coronavirus disease (COVID-19). Routine “passive” chest computed tomography (CT) screening of inpatients detects some pulmonary diseases requiring thoracic surgeries timely. As an essential device for thoracic anesthesia, the double-lumen tube (DLT) is particularly important for anesthesia and surgery. With the continuous upgrading of the DLTs and the widespread use of the fiberoptic bronchoscopy (FOB), the position of DLT in thoracic surgery is gradually becoming more stable and easier to observe or adjust. However, the DLT malposition still occurs during transferring patients from supine to lateral position in thoracic surgery, which leads to lung isolation failure and hypoxemia during one-lung ventilation (OLV). Recently some innovative DLTs or improved intervention methods have shown good results in reducing the incidence of DLT malposition. This review aims to summarize the recent studies of the incidence of left-sided DLT malposition, the reasons and effects of malposition, and summarize current methods for reducing DLT malposition and prospects for possible approaches. Meanwhile, we use bibliometric analysis to summarize the research trends and hot spots of the DLT research.

We re-inventoried red wood ant nests (RWA) in 12 study sites (≈1281 ha) in the Westeifel Volcanic Field, Germany, in an area-wide and integrated ecosystem approach after 12 years. Combined with the re-identification of previously mapped nests using a photo database, this approach leads to more accurate nest counts in (re)inventories. A total increase of nests from 1144 (2009) to 1252 (2021), and a dramatic one for the Heidberg site by 52-fold (2009) and 85-fold (2021) compared to a 1984 inventory was observed, contrasting with earlier postulations of a decline in RWA. Early to medium mature (41-80 years) and mature (³81–140 years) spruce forests were the preferred habitat. Large increase in small nest sizes suggests an increase in new nest settlements also in clearings, despite climate-induced forest dieback over the past decade. A decline in biodiversity in the herbaceous layer was observed; highly proliferating blackberries had no negative impact on RWA nests. Monitoring of woodpecker cavities in RWA nests is suggested as an indirect indicator tool for evaluating populations in forests. Positive ground movement rates caused by the Eifel plume are suggested another factor favoring nest settlements. This study contributes to the urgent update of statistically valid data required to a) effectively substantiate the status-quo of RWA occurrences, b) protect RWA as ecosystem engineers, c) advance understanding of Geo-Bio-Interactions in the wake of climate change, and c) contribute to the German government's Insect Conservation Action Program.

New TLC-densitometric method have been developed for the identification and quantification of paracetamol (PA), propyphenazone (PP) and caffeine (C) of Saridon tablets using the NP-TLC technique combined with densitometry. This method allows for the simultaneous determination of PA, PP, and C in the same sample. Among all tested chromatographic conditions, the mixture consisting of chloroform + toluene + ethyl acetate + ethanol + acetic acid (18:18:7.5:5.0:0.3, v/v) and silica gel 60F254 plate proved to be the most effective for the separation of three tested active pharmaceutical ingredients (APIs) and substances related to paracetamol. The fully validation of the proposed NP-TLC method proves that it is specific, precise, accurate, robust and sensitive. The percentage content in relation to the content declared by the manufacturer is for propyphenazone 99.8%, paracetamol 101.6% and caffeine 100.8%, which are in accordance with pharmacopoeial requirements. The results presented indicate the possibility of using the developed method in the routine control of pharmaceutical preparations containing these APIs. The proposed method is economical and more sensitive compared to the previously proposed planar methods for the simultaneously determination of PA, PP and CAPIs. Will be an What is more, the presented method may be anaxcellent excellent economical alternative when HPLC method is unavailable for such determination.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

This study presents a research plan that utilizes data obtained from wearable devices to identify human activities and gain insights into human behavior. We developed a model capable of classifying activities similar to human behavior and evaluated the effectiveness and generalization capabilities of this model. The data underwent initial preprocessing, including standardization and normalization. Additionally, recognizing the inherent similarities between human activity behaviors, we introduced a multi-layer classifier model. The first layer is a random forest model based on stepwise regression, which may encounter reduced accuracy for similar activities. The second layer employs a Support Vector Machine (SVM) model based on Kernel Fisher Discriminant Analysis (KFDA). KFDA is used to reduce the dimensionality of data points with potential confusion, followed by SVM for classification. The model was experimentally evaluated and applied to four benchmark datasets: UCI DSA, UCI HAR, WISDM, and IM-WSHA. The experimental results demonstrate that our approach achieved recognition accuracies of 99.71%, 98.71%, 99.12%, and 97.6% on these datasets, indicating excellent recognition performance. Furthermore, to assess the model's generalization ability, we performed K-fold cross-validation on the random forest model and utilized ROC curves for the SVM classifier. The results indicate that our multi-layer classifier model exhibits robust generalization capabilities.

New hybrid composites based on the inclusion of a vegetal extract, i.e., Boswellia Serrata extract (BSE), rich in boswellic acids, well known as a potent anti-inflammatory natural drug, in a lamellar solid layered double hydroxide (LDH), i.e. a Magnesium Aluminum Carbonate, were developed and characterized in the present work. The adopted LDH exhibits a layered crystal structure, comprised of positively charged hydroxide layers and interlayers composed of carbonate anions and water molecules, thus it was expected to embed negatively charged boswellic acids. In the present case, a calcination process was also adopted on LDH to increase organic acids loading, based on the replacement of original inorganic anions. An accurate investigation was carried out by TGA, PXRD, FT-IR/ATR, XPS and LC-MS to ascertain the nature, interaction, and quantifica-tion of the active molecules of the vegetal extract loaded in the developed hybrid materials. As a result, a significant disruption of the original layered structure was observed in LDH subjected to calcination (LDHc), and this material was able to include a higher amount of organic acids when its composite with BSE was prepared. However, in vitro tests on composites bioactivity, expressed in terms of antimicrobial and anti-inflammatory activity, evidenced LDH-BSE as a better material compared to BSE and to LDHc-BSE, thus suggesting that, though the embedded organic acids amount was lower, they could be more available since not firmly bound to the clay. The composite was able to significantly decrease the number of viable pathogens such as Escherichia Coli and Staphylococcus aureus, as well as the internalization of toxic active species into human cells imposed to oxidative stress in comparison to the BSE.

A structural study of the 6√3 reconstruction conversion on 4H-SiC substrate surface in an Ar medium with a short sublimation annealing time into quasi-free epitaxial graphene by means of hydrogen intercalation between the upper layer of SiC and the adjacent reconstructed layer was carried out using the technique of reflection high-energy electron diffraction (RHEED) characterizing the surface of a crystalline material. A slight violation of the 6√3 reconstruction layer formation uniformity was found. The results of the study of the crystal structure of quasi-free graphene and single-layer graphene comprising a buffer layer formed on 4H-SiC in the traditional way in an Ar atmosphere without intercalation were compared.

B and T lymphocytes demonstrate important alterations in patients with Systemic Lupus Erythematous (SLE), with significant up-regulation of Double Negative (DN) B cells. Aim of this study was to evaluate correlation of T cell immunity changes with the distinct B cell-pattern SLE. In the present study, Flow cytometry was performed in 30 patients with SLE, on remission, and 31 healthy controls, to detect DN B cells (CD19+IgD-CD27-) and a wide range of T lymphocyte subpopulations, based on the presence of CD45RA, CCR7, CD31, CD28, CD57, defined as naive, memory and advanced differentiated/senescent T cells. Both B and T lymphocytes were significantly reduced in SLE patients. However, the percentage of DN B cells were increased, compared to HC, 12.9(2.3-74.2) vs. 8(1.7-35), p=0.04. Distribution of CD4 and CD8 lymphocytes demonstrated a shift to advanced differentiated subsets. The population of DN B cells had significant positive correlation with most of early differentiated T lymphocytes, CD4CD31+, CD4CD45RA+CD28+, CD4CD45RA+CD57-, CD4CD45RA-CD57-, CD4CD28+CD57-, CD4CD28+CD57+, CD4 CM, CD8 CD31+, CD8 NAÏVE, CD8CD45RA-CD57-, CD8CD28+CD57-, CD8CD28+CD57+. Multiple Regression analysis revealed CD4CD31+, CD8CD45RA-CD57- and CD8CD28+CD57- cells as independent parameters contributing to DN B cells, adjusted R2=0.534, p<0.0001. The predominance of DN B cells in patients with SLE is closely associated with early differentiated T lymphocyte subsets, indicating a potential causality role of DN B cells in T lymphocyte activation.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Many bio-applicable materials, medical devices, and prosthetics combine both polymer and metal components to benefit from their complementary properties. This goal is normally achieved by their mechanical bonding or casting only. Here, we report an alternative easy method for the chemical grafting of a polymer on the surfaces of a metal or metal alloys using alkoxy amine salt as a coupling agent. The surface morphology of the created composites was studied by various microscopy methods, and their surface area and porosity were determined by adsorption/desorption nitrogen isotherms. The surface chemical composition was also examined by various spectroscopy techniques and electrokinetic analysis. Elements distribution on the surface was determined and successful bonding of the metal/alloys on one side with the polymer on the other one was confirmed by alkoxy amine. The composites show significantly increased wettability, reliable chemical stability of the bonding, excellent bacterial anti-adhesive properties and functionality, i.e. the characteristics promising for their application in biomedical field.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

This paper intends to discuss SSLs, how they work, their advantages and drawbacks. It will end with the author’s thoughts on the efficacy of the system and whether it is a viable solution for the majority of network security problems or if those drawbacks prevent that.

The Onion Route Network (also called TOR) is by far the most efficient and widely used anonymity platform with millions of users daily and an expanding size and capacities. Since its public deployment in 2002, the Onion Routing network (also known as TOR) has maintained its leading position and dozens of propositions aiming to improve its performance and enhance the security (anonymity and privacy) have been made. Given the significance of this research area, this work seek to contribute into the improvement of TOR by investigating and testing revolutionary cryptographic and routing mechanism. This work is justified by the current TOR vulnerability and observed weaknesses, and set the challenging aim of covering these security flaws by proposing the relevant security and performances improvement such as the authenticated-encryption for onion construction, the lightened onion encapsulation approach and the secured circuit selection and cell routing mechanisms. The obtained results from implementing the proposed improvements and testing them into a TOR-like simulation platform permit to validate not only, the performances and security contributions brought by the improvement, but also the suitability of their potential implementation into the real TOR network.

This study investigates the Hagen–Poiseuille pipe flow of viscoplastic fluids, focusing on analytical predictions of concrete pumping using the shear-stress-dependent parabolic model. Research highlights encompass solving the steady laminar pipe flow for viscoplastic fluids described by the parabolic model, extending analytical studies to a nonlinear rheological model with easily accessible experimental parameters, presenting detailed results for the two-fluid parabolic model, and introducing computational apps implementing theoretical findings. The parabolic model outperforms linear models, such as the Bingham model, in accuracy by accounting for the nonlinearity in the shear stress and shear rate relations. The influence of rheological parameters on these relations is analyzed, and their versatility is demonstrated by a Wolfram Mathematica-based application program. This approach is adaptable for other models with shear stress as the independent variable, offering valuable insights into viscoplastic fluid flows.

This work focused on the evaluation of some machine learning (ML) models and their application in e-health, using intermediate nodes within an Internet of Things (IoT) platform used for heartbeat anomaly detection. For the evaluation of ML models, a set of statistical validation metrics was selected. These metrics were applied in the training, testing and validation phases of the models. The results obtained can determine relevant factors for the selection of ML models, either based on the statistical and intrinsic efficiency of the ML models, or on their suitability to be implemented in intermediate nodes within an IoT platform. the more Lightweight models such as Simple Linear Regression, Logistic Regression, and K Nearest Neighbors, could easily operate in intermediate nodes, and they are models that require low processing and storage to work. In conclusion, the approach for intermediate nodes of Internet of Things platforms using cognitive networks decreases the processing cost in cloud computing and transfers it to the fog layer.

Ionizing radiation-induced damage in cancer and normal cells leads to apoptosis and cell death, through the intracellular oxidative stress, DNA damage and disorders of their metabolism. Irradiation doses that do not lead to the death of tumor cells can result in the emergence of radioresistant clones of these cells, due to the rearrangement of metabolism and the emergence of new mutations, including those in the genes responsible for DNA repair. The search for the substances capable of modulating the functioning of the tumor cell repair system is an urgent task. Here we analyzed the effect of cerium(III) fluoride nanoparticles (CeF3 NPs) on normal (human mesenchymal stem cells – hMSCs) and cancer (MCF-7 line) human cells after X-ray radiation. CeF3 NPs effectively prevent the formation of hydrogen peroxide and hydroxyl radicals in an irradiated aqueous solution, showing pronounced antioxidant properties. CeF3 NPs are able to protect hMSCs from radiation-induced proliferation arrest, increasing their viability and mitochondrial membrane potential, and, conversely, inducing the cell death of MCF-7 cancer cells, causing radiation-induced mitochondrial hyperpolarization. CeF3 NPs provided a significant decrease in the number of double-strand breaks (DSBs) in normal cells, while in MCF-7 cells the number of γ-H2AX foci dramatically increased in the presence of CeF3 4 hours after irradiation. In the presence of CeF3 NPs, there was a tendency to modulate the expression of most analyzed genes associated with the development of intracellular oxidative stress, cell redox status and the DNA repair system after X ray irradiation. Cerium-containing nanoparticles are capable of providing selective protection of normal cells from radiation-induced injuries and are considered as a platform for the development of promising clinical radioprotectors.

This short review is aimed at giving an overview of catalytic carbonylative double cyclization reactions, which are processes in which suitable organic substrates and carbon monoxide are sequentially activated by a promoting catalyst to afford the formation of two new cycles with concomitant incorporation of carbon monoxide as a carbonyl function into the final product. Paradigmatic examples of this powerful synthetic methodology, which allows the one-step synthesis of complex molecular architectures from simple building blocks using the simplest and readily available C-1 unit (CO) are illustrated and discussed. The review is divided into five sections: 1) Introduction; 2) Functionalized Olefinic Substrates; 3) Functionalized Acetylenic Substrates; 4) Functionalized Halides; 5) Conclusions and Future Perspectives.

Computer vision models of salient object detection attempt to mimic the ability of the human visual system to select relevant objects in images. To this end, the development of deep neural networks on high-end computers has recently made it possible to achieve high performance. However, it remains a challenge to develop deep neural network models of the same performance for devices with much more limited resources. In this work, we propose a new approach for a lightweight salient object detection neural network model, inspired by the cone and spatial opponent processes of the primary visual cortex (V1), that inextricably link color and shape in human color perception. Our proposed model, namely CoSOV1net, is trained from scratch, without using backbones from image classification or other tasks. Experiments, on the most widely used and challenging datasets for salient object detection, show that CoSOV1Net achieves competitive performance (i.e. Fβ=0.931 on the ECSSD dataset) with state-of-the-art salient object detection models, while having low number of parameters (1.14M), low FLOPS (1.4G) and high FPS (211.2) on GPU (nvidia Geforce RTX 3090 TI) compared to the state-of-the-art in the salient object detection or lightweight salient object detection task. Thus, CoSOV1net turns out to be a lightweight salient object detection that can be adapted to mobile environments and resource-constrained devices.

Abstract- Cognitive radio (CR) play an important role in improving spectral efficiency (SE) of wireless communication, meanwhile, intelligent reflecting surface (IRS) is an effective technology to improve the secrecy performance of wireless communication system by adjusting the phase shift and amplitude of channel. Thus, we consider an IRS-aided multiple-input single-output (MISO) CR systems to enhance secrecy rate, which is consists of a single eavesdropping link, a primary network containing the primary receiver (PR), and secondary network including secondary receiver (SR) and the SR transmitter (SR-TX). Specifically, we minimize the transmit power of SR subject to secrecy capacity constraint and interference temperature (IT) constraint on PR, by jointly optimizing the beamforming vector and artificial noise (AN) constraints matrix at SR-TX as well as the phase shift matrix of IRS. Numerical results show that the different values of transmit antennas at the SR-TX and the number of IRS elements can significantly decrease the transmit power under the condition of ensuring secure communication.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

This paper is a further development of our “Proposal of a new double-nozzle technique for in-gas-jet laser resonance ionization spectroscopy” published in journal Atoms earlier in this year. Here, we propose to equip the proposed double-nozzle technique with the RF-only funnel and RF-buncher placed in the gas-jet chamber at 70 mm distance downstream the double-nozzle exit. It allows for highly effective extraction into vacuum heavy ion beams, produced in two-steps laser resonance ionization in the argon supersonic jet. We explored the operation of this new full version of the double-nozzle technique through detailed gas dynamic and then Monte Carlo trajectory simulations, which results are presented and discussed. In particularly, we have shown by calculations that more than 80% of all nobelium-254 neutral atoms, extracted by argon flow from the gas stopping cell through the double-nozzle into the supersonic jet can be extracted into vacuum in a form of pulsed ion beam having low transverse and longitudinal emittance.s dynamic and Monte Carlo simulations

: Two-dimensional instability of a horizontal layer of boiling liquid with a finite height is experimentally studied. In this layer, “vapor columns” rose at the corners of a square rectangular grid. The symmetry of “vapor column” location on the heating surface is considered. The model considers the approach to the boiling crisis in terms of both developed nucleate boiling and transitional boiling (the Zuber problem). When dealing with developed nucleate boiling, the layer of boiling liquid is considered in calculations as an isotropic homogeneous system (foam). It is shown how the conditions on the heating surface (capillary-porous coating) affect external hydrodynamics of the liquid layer and, ultimately, the value of the critical heat flux. The calculation ratio obtained by approaching the boiling crisis with regard to developed nucleate boiling takes into account the dependence of the critical heat flux on the void fraction of the boiling liquid layer. A new solution to the boiling crisis problem is proposed when approaching the crisis from the point of transitional boiling (the Zuber problem). This new solution eliminates some shortcomings of the classical problem (in particular, the void fraction of the layer corresponds to the experiments).

Bone Scan Index (BSI) is an image biomarker for quantification on bone metastasis of cancers. To compute BSI, not only the hotspots (metastasis) but also the bones have to be segmented. Most related researches focus on binary classification on bone scintigraphy: having metastasis or none. Rare studies focus on pixelwise segmentation. In this study we compare three advanced convolutional neural network (CNN) based models to explore the bone segmentation on dataset in house. The best model is Mask R-CNN, which reaches the precision, sensitivity and F1-score: 0.93, 0.87, 0.90 for prostate cancer patients and 0.92, 0.86, 0.88 for breast cancer patients, respectively. The results are the average of 10-fold cross-validation, which reveals the reliability for clinical use on bone segmentation.

PEDOT:PSS (polyethylene dioxythiophene:polystyrenesulfonate) is a commonly used hole injec-tion layer (HIL) in optoelectronic devices due to its high conductive properties and work function. However, the acidic and hygroscopic nature of PEDOT:PSS can be problematic for device stability over time. To address this issue, in this study, we have demonstrated the potential of an organic-inorganic hybrid HIL, by incorporating solution-processed WOx nanoparticles (WOx NPs) into the PEDOT:PSS mixture. This hybrid solution was found to have a superior hole transport ability and low Ohmic contact resistance, contributing to higher brightness (~62 000 cd m-2) and current efficiency (13.1 cd A-1) in the manufactured quantum-dot based light-emitting diodes (QLEDs). In addition, the resulting devices achieved a relative operational lifetime of 7,071 hours, or approxi-mately twice that of traditional QLEDs with PEDOT:PSS HILs. The proposed method is an un-complicated, reliable and low-cost way to achieve long operational lifetimes without sacrificing efficiency in optoelectronic devices.

Calcium sulfate (CS) materials containing terbium ions at 0, 1.0, or 2.0 mol.% were obtained by mechanochemical synthesis. According to X-ray diffraction data, the powder materials are characterized by the presence of a CaSO4×0.5H2O phase, while Tb3+ is incorporated into the lattice at ≤1.0 mol.%. Specific surface area enlarged from 2.1 to 22.5 m2/g as crystallite size decreased from 68 to 31 nm and the Tb3+ concentration increased up to 1.0 mol.%. Thermal analysis showed that terbium slightly raises the temperature of CaSO4×2H2O-to-CaSO4 transition. The presence of Tb3+ did not affect the solubility of the CS cements. Furthermore, after 7 days of soaking of the materials in a simulated body fluid, a calcium phosphate layer formed corresponding to a hydroxyapatite phase, in contrast to the pure cements. Luminescent properties were studied by excitation at 276 nm. The recorded emission peaks of the CS materials indicated that the luminescence of the samples is green and blue, with the most intense luminescence observed for samples containing 1.0 mol.% Tb3+. The developed materials can find applications in medicine as bioimplants for the regeneration and restoration of bone tissue with a possibility of noninvasive monitoring of the bone restoration process.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

Due to the special characteristics of the shooting distance and angle of remote sensing satellites, the pixel area ratio of ship targets is small and the feature expression is insufficient, which leads to unsatisfactory ship detection performance and even situations such as missed detection and false detection. In this study, we propose an improved-YOLOv5 algorithm. The improvement strategies mainly include: (1) Add the Convolutional Block Attention Module (CBAM) into the Backbone to enhance the extraction of target-adaptive optimal features; (2) Introduce cross-layer connection channel and lightweight GSConv structure into the Neck to achieve higher-level multi-scale feature fusion and reduce the number of model parameters; (3) The Wise-IoU loss function is used to cal-culate the localization loss in the Output, and assign reasonable gradient gains to cope with dif-ferences in image quality. In addition, during the preprocessing stage of experimental data, a me-dian and bilateral filter method is used for noise reduction to reduce interference from ripples and waves and highlight the information of ship features. The experimental results show that Im-proved-YOLOv5 has a significant improvement in recognition accuracy compared to various mainstream target detection algorithms; Compared to the original YOLOv5s, the mean Average Precision (mAP) has improved by 3.2% and the Frames Per Second (FPN) has accelerated by 8.7%.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

Weak interaction processes continue to be hot topics in fundamental physics research. In this paper, we briefly review some recent advances in the theoretical study of beta and double-beta decays that include both the nuclear and atomic part of these processes. On the nuclear side, we present a statistical approach for the computation of the nuclear matrix elements (NME) for neutrinoless double-beta (0νββ). A range of NME values, the most probable value for NME, and the associated theoretical uncertainty are given. Correlations with other related observables are shown as well. On the atomic side, we first briefly review the methods used to get the electrons’ wave functions. Further, we use them for the computation of some relevant kinematic quantities such as Fermi functions, electron spectra and angular correlation between the emitted electrons. Then, we present applications of these calculations to the experimental data analysis related to the search of the Lorentz invariance violation in two-neutrino double-beta (2νββ) decay and description of the decay rates and decay rate ratios for allowed and unique forbidden electron capture (EC) processes.

Internet of Things (IoT) is a massive network of tiny devices connected internally and to the in-ternet. It is uniquely identified in the network (i.e. dedicated IP) and can share the information with other devices. However, the low power and low resources that distinguish IoT devices render them unsecure and targeted by different kinds of attacks since IoT devices cannot toler-ate heavy security models. Also, due to the heavy nature of famous protocols such as HyperText Transport Protocol (HTTP), it is costly to be used with IoT devices, and alternatively, different lightweight protocols are implemented to fit IoT devices. One of the prevailing protocols used over IoT networks is the Constrained Application Protocol (CoAP). Therefore, CoAP is popular, and that makes it targeted by different types of attacks. One of the major attacks that target CoAP is distributed denial of service (DDoS) attacks. DDoS aims to overwhelm the resources of the target and make them unavailable to legitimate users. As a result, different kinds of meth-ods were used to secure CoAP against DDoS attacks such as Datagram Transport Layer Secu-rity (DTLS) and Lightweight and Secure Protocol for Wireless Sensor Networks (LSPWSN). However, the existing models suffer from two issues: DTLS is not designed for constrained devices and is considered a heavy protocol. Besides, LSPWSN is working over the network layer, not in the application layer that CoAP works on. In this paper, we build a machine learn-ing model that can detect the DDoS attacks against CoAP with an accuracy of 98%. The CIDAD dataset is extended from ~11000 to 100,000 samples using GANs because it has fewer samples of malware (less than 0.2% of the total dataset). Our model outperforms the existing models that target securing CoAP in the application layer and obtains 93% of accuracy.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

Light can interfere like a wave in a multi-path experiment, but it also has particle properties when interacting with matter. In a closer look, the interference pattern is created by many individual detections ("clicks"), which do not all occur simultaneously. An established assumption is therefore that a single light particle is capable of interfering with itself by superimposing all possibilities to get from the source to the detector. This is in stark contrast to our experience with macroscopic objects, which always "decide" in favour of only one of the alternative paths.In 2010, Jin et al. (Ref. 15) described an event-based model which allowed the authors to show that an interference pattern consisting of clicks can arise in a multi-path experiment even if photons, like macroscopic objects, only follow one path. To do this, photons must be able to transmit the information about their travelling duration to the detector and the detector must have a basic memory. A threshold function uses the message of several light quanta to decide whether a single detection is initiated, which is not the evidence for a single photon. In this "proof of principle", the authors do not claim that the detector function is a realistic one.In the present paper, this detector is replaced by a material consisting of ionizable molecules whose interaction with light takes place according to a modified version of Einstein's radiation laws. Based on this, a photon pair interaction mediated by matter takes place, which in a multi-path experiment generates an interference pattern of clicks at the detector, even if an arbitrary amount of time elapses between the individual detections. In the present model an interference pattern with minima that have less than half the intensity of the maxima is the result of a peculiar behaviour of the detector: In this case, the entirety of its electrons must be described as a unit (a “field”) with many equidistant energy levels. The results of a simulation are presented which enable the model to be tested in experiments.

The Review examines studies aimed at the organization of energy (non-mechanical) control of high-speed flow/flight using spatially multi-component plasma structures and combined energy deposition. The Review covers selected works on experimental obtaining and numerical modeling multi-component plasma structures and use of sets of actuators based on the plasma of such a spatially type for the purposes of control of shock wave/bow shock wave – energy source interaction, as well as control of shock wave – boundary layer interaction. A series of works on repetitive multiple laser pulse plasma structures is also analyzed from the point of view of examining shock wave/bow shock wave boundary layer interaction. Self-sustained theoretical models for laser dual-pulse, multi-mode laser pulses and self-sustained glow discharge are also considered. Separate sections are devoted to high-speed flow control using combined physical phenomena and numerical prediction of flow control possibilities using thermal longitudinally layered plasma structures. The wide possibilities for organization and applying spatially multi-component structured plasma for the purposes of high-speed flow control are demonstrated.

Recent studies have proven that synthetic aperture radar (SAR) automatic target recognition (ATR) models based on deep neural networks (DNN) are vulnerable to adversarial examples. However, existing attacks are easily failed in the case where adversarial perturbations cannot be fully fed to victim models. We call this situation perturbation offset. Moreover, since background clutter takes up most of the areas in SAR images and has low relevance to recognition results, fooling models with global perturbations is quite inefficient. This paper proposes a semi-whitebox attack network, called Universal Local Adversarial Network (ULAN), to generate universal adversarial perturbations (UAP) for the target regions of SAR images. In the proposed network, we calculate the model’s attention heatmaps through layer-wise relevance propagation (LRP), which is used to locate the target regions of SAR images that have high relevance to recognition results. In particular, we utilize a generator based on the U-Net to learn the mapping from noise to UAPs and craft adversarial examples by adding the generated local perturbations to target regions. Experiments indicate that the proposed method fundamentally prevents perturbation offset and achieves comparable attack performance to conventional global UAPs by perturbing only a quarter or less of SAR image areas.

We investigated experimentally, analytically and numerically the formation process of double emulsion formations under dripping regime in a tri-axial co-flow capillary device. The results show that mismatches of core and shell droplets under a given flow condition can be captured both experimentally and numerically. We propose a semi-analytical model using the match ratio between the pinch-off length of the shell droplet and the product of the core growth rate and its pinch-off time. The mismatch issue can be avoided if the match ratio is lower than unity. We considered a model with the wall effect to predict the size of the matched double emulsion. The model shows slight deviations with experimental data if the Reynolds number of continuous phase is lower than 0.06, but asymptotically approaches to good agreement if the Reynolds number increases from 0.06 to 0.14. The numerical simulation generally agrees with the experiments under various flow conditions.

CRCMSS/pMMR contain a significantly increased fraction of TREM2+ macrophages (TAMs) and CD66+ neutrophils (TANs) together with decrease of CD4-CD8-CD3+ double negative T lymphocytes (DNTs); no differences were revealed by the analysis of myeloid and plasmacytoid dendritic cell populations. A fraction of tumor-infiltrating T-cells display an exhausted phenotype, co-expressing PD-1 and TIM-3. Remarkably, expression of PD-L1 on fresh tumor cells and TAMs was undetectable even after in vitro stimulation with interferon-γ. These findings confirm the immune suppressive microenvironment of CRCMSS/pMMR characterized by dense infiltration of TAMs, occurrence of TANs, lack of DNTs, T-cell exhaustion and interferon-γ unresponsiveness by host and tumor cells. Appropriate bypass strategies should consider these combinations of immune escape mechanisms in CRCMSS/pMMR.