In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

The scheme to realize high speed (~250Gb/s) all-optical Boolean logic gates using semiconductor optica amplifiers with quantum-dot (QD-SOA) is introduced and analyzed in this review. Numerical simulation method was presented by solving the rate equation and taking into account nonlinear dynamics including carrier heating and spectral hole-burning. Binary phase shift keyed (BPSK) signal and on-off keyed signal are used to generate high speed all-optical logic gates. The applications based on all-optical logic gates such as, all-optical latches, pseudo random bit sequence (PRBS) generation and all-optical encryption, are also discussed in this review. Results show that the scheme based on QD-SOA is a promising method for the realization of high speed all-optical communication system in the future.

This work aims to follow the corrosion behavior of copper in 3 wt% NaCl solution in the presence of a bio-oily extract. Spent coffee grounds (SCG), a highly recyclable and usable biomass - often thrown away and becoming a serious threat to the environment - , has a fraction of oils (12%) that we have opted to use as a corrosion inhibitor for copper. The extraction was carried out using n-hexane as the solvent for the decoction. The oily fraction was analyzed by Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). Potentiodynamic polarization measurements have revealed SCG extract acts as a cathode-type inhibitor for copper in saline media, mainly preventing the diffusion of oxygen molecules toward the substrate. As the extract concentration increased, the inhibition efficiency has improved as well, reaching 95.78 % with 0.6 g/L of SCG extract. The obtained results by electrochemical impedance spectroscopy (EIS) are in accordance with the order of inhibitory efficiency obtained by potentiodynamic polarization. We have found that the SCG extract adsorption process on copper surface is spontaneous and complies with Langmuir isotherm.

An orthogonal pore ('orthopore') is conceptually based on an electrolytic cell with a standard pore (the main or 'longitudinal' pore) between cis and trans compartments filled with electrolyte and augmented by a secondary or 'transverse' pore in the form of a channel that is perpendicular to and intersects the main pore. Orthopores can be designed at different scales: macro through micro to nano. With nano-sized pores an analyte (polymer) can be threaded through the main pore and exposed at the junction to electrolyte flow through the secondary pore. Polymer translocation speeds are then independent of the current measured, which can be of an arbitrary magnitude even with the polymer stationary. Orthopores have a wide range of potential applications, including polymer (DNA and protein) sequencing, DNA unzipping, logic circuitry, and protein identification. The present report shows how orthopores can be used to implement boolean logic.

This study introduces a gate design that uses pass transistor switches and enables the implementation of all nec- necessary logic gates with a single structure. This gate design can be used for efficient circuit resizing and creating secure obfuscated circuits. This work also presents simulation results that demonstrate the effectiveness of the gate in performing various logic gate operations.

We report the electrical properties of Al0.3Ga0.7N/GaN heterojunction field effect transistor (HFET) structures with a Ga2O3 passivation layer grown by metal-organic chemical vapor deposition (MOCVD). In this study, three different thicknesses of Ga2O3 dielectric layers were grown on Al0.3Ga0.7N/GaN structures leading to metal-oxide-semiconductor-HFET or MOSHFET structures. X-ray diffraction (XRD) showed the (¯201) orientation peaks of -Ga2O3 in the device structure. The van der Pauw and Hall measurements yield the electron density of ~ 4 x1018 cm-3 and mobility of ~770 cm2V-1s-1 in the 2-dimensional electron gas (2DEG) channel at room temperature. Capacitance-voltage (C-V) measurement for the on-state 2DEG density for the MOSHFET structure was found to be of the order of ~1.5 x1013 cm-2. The thickness of the Ga2O3 layer was inversely related to the threshold voltage and the on-state capacitance. The interface charge density between the oxide and Al0.3Ga0.7N barrier layer was found to be of the order of ~1012 cm2eV-1. The annealing at 900° C of the MOSHFET structures revealed that the Ga2O3 layer was thermally stable at high temperatures resulting in insignificant threshold voltage shifts for annealed samples with respect to as-deposited (unannealed) structures. Our results show that the MOCVD-gown Ga2O3 dielectric layers can be a strong candidate for stable high-power devices.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

Background: Digital health significantly affects healthcare delivery. Moreover, empirical studies on the utilization of telehealth in Dubai are limited. Accordingly, this study examines the utilization of telehealth services in Dubai Health Authority (DHA) facilities and the factors associated with telehealth appointment completion and turnaround time. Methods: This cross-sectional study examines patients who used telehealth services in DHA from 2020 through 2021 using 241,822 records. A binary logistic regression model was constructed to investigate the association between appointment turnaround time as a dependent variable and patient and visit characteristics as independent variables. Results: Of the total scheduled telehealth visits, more than three-quarter (78.55%) were completed. Older patients, non-Emiratis, patients who had their visits in 2020, patients who had video visits, and those who sought family medicine as a specialty had a shorter turn-around time to receive their appointment. Conclusions: This study identifies several characteristics associated with the turn-around time. Moreover, technological improvements focusing on specialties that can readily be addressed through telehealth and further research in this domain will improve service provision and support building an evidence base.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

Introduction: The presence of multiple comorbidities increases the risk of all-cause mortality, but the effects of the comorbidity sequence before the baseline date on mortality remained unexplored. This study investigated the relationship between coronary heart disease (CHD), atrial fibrillation (AF) and heart failure (HF) sequence on all-cause mortality risk in type 2 diabetes mellitus. Methods: This study included patients with type 2 diabetes mellitus prescribed antidiabetic/cardiovascular medications in public hospitals of Hong Kong between January 1st, 2009 and December 31st, 2009 with follow-up until death or December 31st, 2019. Cox regression was used to identify comorbidity sequences predicting all-cause mortality in patients with different medication subgroups. Results: A total of 249291 patients (age: 66.0±12.4 years, 47.4% male) were included. At baseline, 7564, 10900 and 25589 patients had AF, HF and CHD, respectively. Over follow-up (3524±1218 days), 85870 patients died (mortality rate: 35.7 per 1000 person-years). Sulphonylurea users with CHD developed later, but insulin users with CHD developing earlier, in the disease course had lower mortality risks. Amongst insulin users with two of the three comorbidities, CHD with preceding AF (hazard ratio [HR]: 3.06, 95% CI: [2.60-3.61], p<0.001) or HF (HR: 3.84 [3.47- 4.24], p<0.001) had a higher mortality. In users of lipid-lowering agents with all three comorbidities, those with preceding AF had higher risk of mortality (AF-CHD-HF: HR: 3.22, [2.24-4.61], p<0.001; AF-HF-CHD: HR: 3.71, [2.66-5.16], p<0.001). Conclusion: The sequence of comorbidity development affects the risk of all-cause mortality to varying degrees in diabetic patients on different antidiabetic/cardiovascular medications.

In recent times, there has been significant enthusiasm for the development of all solid state batteries. This interest stems from a dual focus on safety—addressing concerns related to toxic and flammable organic liquid electrolytes—and the pursuit of high energy density. \cite{SCHNELL2018160,Zheng2018}. While liquid electrolyte batteries constitute for now the vast majority of commercial cells, solid electrolyte batteries show great promise. In parallel with experimental research, computational models \cite{GrazioliEtAlCM2016} clarify the several fundamental physics \cite{LiMonroeARCBM2020} that take place throughout battery operations. We review some classical models, emphasizing the conceptual advancements documented in the most recent works.

Prime number-related issues can be viewed from drastically different perspectives by examining the close connections between prime numbers and composite numbers. We think that multiple perspectives are the pillars on the path to solutions so we have created this study. As a result of the study, we proposed two new formulas by presenting three theorems and one proof for each theorem, a total of three proofs. We proved that the formula p · n + p returns a composite number in the first of the theorems, which is the preliminary theorem. Our first theorem except the preliminary theorem is that the formula p · n + p returns all composite numbers, and we proved that too. Finally, we created Theorem II using Theorem I to use in our other work and proved that the formula 2 · n · p + p returns all odd composite numbers, which is Theorem II. Afterward, we presented the similarities of the 2 · n · p + p formula we put forth with another known formula.

In the pursuit of energy-efficient spiking neural network (SNN) hardware, synaptic devices lev-eraging emerging memory technologies hold significant promise. This study investigates the ap-plication of the recently proposed HfO2/SiO2-based interface dipole modulation (IDM) memory for synaptic spike timing-dependent plasticity (STDP) learning. Firstly, through pulse measure-ments of IDM metal-oxide-semiconductor (MOS) capacitors, we demonstrate that IDM exhibits an inherently nonlinear and near-symmetric response. Secondly, we discuss the drain current re-sponse of a field-effect transistor (FET) incorporating a multi-stack IDM structure, revealing its nonlinear and asymmetric pulse response, and suggest that the degree of the asymmetry depends on the modulation current ratio. Thirdly, to emulate synaptic STDP behavior, we implement dou-ble-pulse-controlled drain current modulation of IDMFET using a simple bipolar rectangular pulse. Additionally, we propose a double-pulse-controlled synaptic depression that is valuable for optimizing STDP-based unsupervised learning. Integrating the pulse response characteristics of IDMFETs into a two-layer SNN system for synaptic weight updates, we assess training and classification performance on handwritten digits. Our results demonstrate that ID-MFET-based synaptic devices can achieve classification accuracy comparable to previously re-ported simulation-based results.

Background: Both hypertension and carotid atherosclerosis are independent risk factors for cardiovascular disease. Understanding their combined impact could enhance risk assessment and management strategies. Hypothesis: We hypothesized that the synergistic effects of hypertension and carotid plaques would increase the risk of both cardiovascular events and all-cause mortality. Methods: A follow-up study was conducted at the Preventive Cardiology department of Vilnius University Hospital Santaros klinikos between 2012 and 2021. The study recruited participants aged 40-60 who did not have overt CVD and were part of the Lithuanian High Cardiovascular Risk primary preventive program. The study collected demographic and clinical data, including an ultrasound assessment of carotid plaque. The participants were monitored for 4-10 years for CVD events and all-cause mortality. Results: Among 6,138 participants, 954 (16%) experienced cardiovascular disease (CVD) events. The presence of carotid plaque on both sides was significantly associated with CVD events, myocardial infarction, and all-cause mortality. However, the combination of hypertension and carotid plaque did not significantly increase the risk for CVD events, stroke, or all-cause mortality. Conclusion: The combination of hypertension and carotid plaque did not significantly increase the risk of CVD events or all-cause mortality. CV events depend on the spread of the atherosclerosis process in the carotid vessels.

Alterations in the composition and diversity, metabolism, and products of the microbiome, and of the gut microbiome (GM), have been shown to be closely associated with the onset and progression of many human diseases, including cancer (i.e. hematological neoplasms). Acute lymphoblastic leukemia (ALL) is the most common form of childhood malignancy. Affected cases present typical alterations of GM, followed by inflammation, which contribute to its progression, response to therapy, as well as possible relapses. Recent evidence also reports that GM influences the development and functions of the newborn's hematopoietic system through the process of developmental programming during fetal life, as well as its susceptibility to the onset of onco-hematological pathologies, namely ALL. Furthermore, in children with ALL, GM has been found to vary in composition, variety, and functions during the clinical stages of ALL, and such variation may influence and predict the complications and prognosis of ALL after chemotherapy treatment or stem cell hematopoietic transplant. Here, we suggest some therapeutic strategies, which can be applied at two levels of intervention to recover the microbiome, and consequently prevent/delay ALL or arrest its progression.

Using publicly available data for 28 EU/EES countries from Eurostat and Our World in Data, we investigate how the current rate of Covid vaccination in a country compares to its average rate of excess mortality (EM) in the pandemic to date. We find that, in the linear regression, the correlation between average EM and vaccination rate is strongly negative, a priori evidence to support the claim that the Covid vaccines have saved many lives. However, a closer analysis of the timeline suggests otherwise. The correlation was already strongly negative before the vaccines were rolled out and is only weakly negative thereafter. In theory, survivor bias could still explain this shift, especially since waves of EM closely align with Covid waves. However, we find in addition that about half of our 28 countries experienced higher EM in 2022 than in 2021, and all that did so have higher than average vaccination rates. This is something which survivor bias cannot explain and raises the real possibility that the vaccines have not just failed to save many lives, but may have already caused net harm. Moreover, any such harm may be ongoing since we find that EM and vaccination rates have been consistently positively correlated since April 2022. We show that all these findings are robust to several different ways of measuring EM and/or vaccination rates. Finally, using public data from Worldometers, we show that the correlation over time of official Covid mortality rates with current vaccination rates closely tracks that of EM rates, even as Covid mortality has waxed and waned and even in the post-omicron period.

Emergency Management has not developed in a cohesive or comprehensive manner. Differing terms are used to name identical concepts. A standard comprehensive doctrine for the important development of emergency management is needed. In this paper I explain a doctrinal framework for emergency management. The paper states a clear identification of the five dimensions, and each of their components, necessary to the informed practice of Emergency Management. Although emergencies vary in cause and severity, the process of Emergency Management necessary for optimal handling of these emergencies varies little. The “All Hazards Approach” to emergency management establishes and reinforces commonality in processes, procedures, planning templates and organizational structure. The three types of agencies associated with emergency management activities are discussed, including the subject matter agency, coordinating agency, and supporting agency. The four critical functions of emergency management are detailed, and include mitigation, preparedness, response, and recovery, often all carried out concurrently. The ten activities, and seven resources of emergency management are highlighted. There are many ways to represent the integration of these five dimensions, to ensure completeness, while ensuring clarity; the two most common are described. When experts in Emergency Management follow the doctrine, they can coordinate all those involved to be sure that all aspects of any hazard are considered, and that all organizations/agencies, functions, activities, and resources of Emergency Management are coordinated and optimally active. Following this process is the only way to ensure the best outcomes from any emergency.

ASTM A743 CA6NM alloy is a martensitic stainless steel typically used in energy industry -runners and hydraulic turbine components- due to its superior toughness, yield and fatigue properties. In both the manufacturing, shielded metal arc welding is applied to join for this grade steels. However, weldability of the steels is limited due to formation of hard and brittle phases such as untempered martensite during welding and post weld heat treatment processes. The formation causes a reduction in toughness. In this study, influence of post-weld heat treatment procedure (single tempering and double tempering) and parameters on microstructure and hardness of AWS410NiMo all weld metal. Hardness tests were conducted from weld metal. Microstructures of the all weld metals subjected to different heat treatment process were characterized.

We design an asymmetric nonlinear optical nanoantenna composed of a dielectric nanodisk and an adjacent nanobar. The proposed composite structure made of AlGaAs exhibits resonant response at both the fundamental and doubled frequencies. Being driven by the strong magnetic dipole resonance at the pump wavelength and a high-quality mode at the harmonic wavelength, the efficient second-harmonic radiation is generated predominantly along the vertical directions under the normally incident plane-wave excitation.

The eco-efficiency of cultivated land use (ECLU) is an important indicator for the construction of ecological civilization in China. Exploring the spatiotemporal dynamic evolution of the ECLU is helpful for sustainable use of arable land, ensuring food security and ecological security. However, previous studies have mostly focused on the use of a slacks-based measure (SBM) model for ECLU measurement, ignoring the more accurate epsilon-based measure (EBM) model. Therefore, in this study, firstly, we explored the conceptual framework of ECLU, and then, based on the panel data of the counties in the region around Beijing and Tianjin from 2005 to 2020, we investigated the spatial and temporal evolution of ECLU by using the Super-EBM model, kernel density estimation method, and spatial Markov chain model. Results displayed: (1) From 2005 to 2020, the ECLU in the region around Beijing and Tianjin displayed an increasing state, but the average value was only 0.55. (2) The time evolution of the ECLU has gradually polarized, the internal gap has widened, but it tends to stabilize. (3) The ECLU in the region around Beijing-Tianjin was more inclined to keep it the same and there was a "club convergence" phenomenon, which was meaningfully affected by the background of neighboring areas. In the light of local conditions, the government should reasonably formulate the path to optimize the ECLU, strengthen the linkage with the surrounding cities, and bring into play the positive spillover effect.

Novel approaches under the extreme conditions of ultra-high gravity of a super massive black hole allow us to assume that the spacetime degrades into the single dimension of time. A unique interpretation of the non-relativistic Schrödinger equation together with the relativistic Klein-Gordon and Dirac equations is presented by swapping the three dimensional space derivatives with the singular time derivative in the D’Alembertian operator. This apparatus reveals a unique time dependent wave equation that results in some implications such as possible time quantization with the intervals of around 3.36 × 10−21 ? which is in the order of uncertainty in time, ∆? = 1.3 × 10−21 ?, calculated from the energy-time version of the Heisenberg uncertainty principle for electrons. As a result of this, an antisymmetric wave function around the edge of the event-horizon zone appears and indicates that the virtual particle-antiparticle pairs of the electron field split into two real components with the spin-up and down states, reconfirming the Hawking radiation. Energy eigenvalues calculated from the application of the Dirac equation satisfies the preservation of energy and charge. The wave equation invoked in this study reduces into the time dependent Dirac equation within the neighborhood of zero-point, ? = 0, insuring the relevance of the evaluations.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

The article presents the results of tests related to failure analysis and finding ways to diagnose used semiconductor elements, among other, in power electronics converter systems on vessels and offshore facilities (drilling and production rigs, wind turbines). Diagnostic relationships were found between the temperature change in the above systems and the signals generated in form of elastic waves of acoustic emission.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

This paper presents a unified reconfigurable coordinate rotation digital computer (CORDIC) processor for floating-point arithmetic. It can be configured to operate in multi-mode to achieve a variety of operations and replaces multiple single-mode CORDIC processors. A reconfigurable pipeline-parallel mixed architecture is proposed to adapt different operations, which maximizes the sharing of common hardware circuit and achieves the area-delay-efficiency. Compared with previous unified floating-point CORDIC processors, the consumption of hardware resources is greatly reduced. As a proof of concept, we apply it to 1638416384 points target Synthetic Aperture Radar (SAR) imaging system, which is implemented on Xilinx XC7VX690T FPGA platform. The maximum relative error of each phase function between hardware and software computation and the corresponding SAR imaging result can meet the accuracy index requirements.

The stability issues in the widely known organic inorganic halide perovskite, CH3NH3PbI3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs2AgBiBr6 and Cs2TiBr6 is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide bandgap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, bandgap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Alveolar Rhabdomyosarcoma (ARMS), an invasive subtype of Rhabdomyosarcoma (RMS), is associated with chromosomal translocation events resulting in one of two oncogenic fusion genes PAX3-FOXO1 or PAX7-FOXO1. ARMS patients exhibit an overexpression of the pleiotropic cytokine Transforming growth factor beta (TGF-β). This overexpression of TGF-β1 causes an increased expression of a downstream transcription factor called SNAIL, which promotes Epithelial to Mesenchymal Transition (EMT). Overexpression of TGF-β also inhibits myogenic differentiation, making ARMS patients highly resistant to chemotherapy. In this review, we first describe different types of RMS and then focus on ARMS and the impact of TGF-β in this tumor type. We next highlight current chemotherapy strategies including a combination of FDA approved drugs vincristine, actinomycin D, and cyclophosphamide (VAC), Cabozantinib, Bortezomib, Vinorelbine, AZD 1775 and cisplatin. Lastly, we discuss chemotherapy agents that target the differentiation of tumor cells in ARMS which include all trans retinoic acid (ATRA) and 5-Azacytidine. Improving our understanding of the role of signaling pathways, such as TGF-β1, in the development of ARMS tumor cells differentiation will help inform more tailored drug administration in the future.

The knowledge on anatomy, function, biomechanics, and role on surgical procedures of the anterolateral ligament (ALL) of the knee is still controversial. Only a few papers have examined the ALL in children. The aim of this review is to analyse all the available literature about ALL in pediatric population. Following the PRISMA criteria, the literature was systematically reviewed, examining all the articles about ALL in pediatric patients. Eight articles were involved in the study. Five cadaveric studies, 2 diagnostic studies and 1 Cross-sectional study were found. The identification of the ALL is not always possible in diagnostic studies using the Magnetic Resonance (MRI) or in dissecting specimens. A high variability in the presence of the ligament, in its origin and insertion were found among the studies. In younger patients is more difficult to identify the ligament than in older children, suggesting that its presence may develop at some point during the growth. Further studies are needed for a detailed knowledge of the ALL.

Aircraft emissions represent a relevant amount of human induced CO2. Globally, up to 2.5 per cent of such emissions stem from the aviation industry. In order to investigate the effects within the atmosphere, realistic flight profiles are necessary to provide quantitatively tangible values of emissions. The flight profiles and the according fuel consumption can be calculated by using waypoints from flight plans and Base of Aircraft Data (BADA). This paper presents an approach to refine the fuel consumption by integrating the passenger load into the calculation. Since effects of emissions have to be assessed on a greater scale, such as on the European air traffic network, the presented approach provides cost functions for CO2 emissions for different aircraft types and load factors. The cost functions were derived by means of regression analyses of BADA based calculated flight profiles with a step size of one second. The calculations are based on real historic traffic scenarios of several days. The derived aircraft specific fuel burn coefficients enable a simple and efficient integration of CO2 estimations depending on the flight distance, load factor and aircraft type. This can be applied to large traffic scenarios to also study different set-ups such as travel restrictions, other disruptions or an alteration in the traffic system as a whole. In order to enable the assessment of further aspects of such changes to the European air traffic system at large and to foster reproducibility and comparability of related studies, we provide further general-purpose cost estimation functions for several important key characteristics. Besides fuel consumption, we develop cost estimations for air navigation fees and maintenance for conventional aircraft. Those functions are also provided for the design concept of a short-range all-electric aircraft. This propeller aircraft features game-changing technologies such as active laminar flow control, active load alleviation and advanced materials and structure concepts. The approaches discussed in this paper will focus on the generic aspects of aircraft related costs, which can be derived from general available data. For the sake of reproducibility, the results will be made publicly available.

To study the influence of electrothermal effect of ESD protection device on the reliability of inte-grated circuit,a theoretical model of ESD protection device thermal resistance is constructed in the paper based on the Conservation of Energy Principle. By analyzing the temperature relativity between electricity parameter and thermology parameter of ESD protection device characterized by self-heating thermal resistance, the quantitative relationship expression of physical parameter and geometric parameter is obtained, which can be used to improve ESD protection device elec-tro-thermal effect. The simulation testing and the real tape-out testing of ESD protection device self-heating thermal resistance based on ggNMOS are shown and compared. It is concluded that self-heating thermal resistance is an effective index for the protection device electrothermal char-acterization. Based on the established model, the self-heating thermal resistance could be decreased to improve the homogeneity of the heat transference. The uneven distribution of device temperature can be reduced, and the overall reliability of chips can be improved.

A new kind of quantum gates, higher braiding gates, as matrix solutions of the polyadic braid equations (different from the generalized Yang-Baxter equations) is introduced. Such gates lead to another special multiqubit entanglement which can speed up key distribution and accelerate algorithms. Ternary braiding gates acting on three qubit states are studied in details. We also consider exotic noninvertible gates which can be related with qubit loss, and define partial identities (which can be orthogonal), partial unitarity, and partially bounded operators (which can be noninvertible). We define two classes of matrices, star and circle ones, such that the magic matrices (connected with the Cartan decomposition) belong to the star class. The general algebraic structure of the introduced classes is described in terms of semigroups, ternary and $5$-ary groups and modules. The higher braid group and its representation by the higher braid operators are given. Finally, we show, that for each multiqubit state there exist higher braiding gates which are not entangling, and the concrete conditions to be non-entangling are given for the obtained binary and ternary gates.

Market channel choice makes important contributions to the incomes and other livelihood attributes among smallholder farmers in developing countries. Often considered from a number of perspectives, the dominant view articulated suggests an advantageous integration into formal market channels. This position is questioned as it has implications for smallholder farmers’ food security and rural incomes. Using a mixed methods approach, the study collected primary data from 174 smallholder farmers and applied both a descriptive and multinomial logit regression model to analyze factors contributing to cocoyam production and market channel choices among respondents in the study area. Findings indicate that financial returns and available markets were key factors in cocoyam production, while amount received was a driver of market channel choice among 89% of respondents who sold directly at farm-gate. Farmers’ age (p=0.044), household size (p=0.043), distance to market (p=0.021), additional income (p=0.017) and amount received (p=0.014) were significant variables (p<.05) in the determinants of market channel choice. The study recommended improving market information provision and strengthening farmer associations which will enable smallholder farmers in rural communities to make informed choices with respect to produce price, access other markets and consolidate their collective market bargaining position.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

Background: the study aimed at comparing the prognostic importance of Heart Rate (HR) and of QT corrected (QTc) according to Fridericia, Framingham and Bazett methods, in a large non-selected population. Methods: the analysis of digital Electrocardiograms archived from 2008 to 2022 in the metropolitan area of Modena, Italy, was made. The population under study was divided into three age-groups and survival analysis was performed. Results: 131.627 patients were enrolled and during the follow-up (mean 1641.4 days), all-cause mortality was 8.9%. Both HR and QTc were associated with mortality. All-cause mortality significantly increased from HR values greater than 81 BPM and from QTc values greater than 440 msec in young subjects and 455 msec in old subjects (values of the 75th percentiles/optimal operating point). Cox analysis confirmed the better prognostic value of Bazett’s QTc and of HR in the whole population and in the three age-groups. Conclusion: Bazett’s method performed better than other methods but unexpectedly HR had the same or a better correlation with all-cause mortality. Since HR is simple and readily available, its evaluation should be improved. However, reference values for QTc and for HR are difficult to define causing many confounding factors and further population-study are required.

Cloud-induced atmospheric extinction and occlusion have a major effect on the effectiveness and quality of telescope observations. Real-time cloud cover distribution and long-term statistical data are essential for astronomical siting and telescope operations. At ground-based astronomical telescope sites, cloud cover distribution is currently analyzed using manual observation methods. However, the main disadvantages of manual observation methods are human subjective, heavy workloads and poor real-time performance. Therefore, a real-time automatic cloud images classification method is desperately needed. This paper presents a new cloud identification method, which is named PSO+XGBoost model by combining eXtreme Gradient Boosting (XGBoost) and Particle Swarm Optimization (PSO). The entire cloud image is divided into 37 sub-regions in order to more precisely identify the distribution of the clouds. 19 features are then extracted, including the sky background, star density, lighting conditions, and subregion grayscale values. The experimental results have shown that the overall classification accuracy of 96.91% and our model is able to outperform several state-of-the-art baseline methods. Our approach achieves high accuracy in comparison with the manual observation methods. Moreover, this method meets telescope real-time scheduling requirements.

All-solid-state lithium batteries (ASSLBs) using argyrodite electrolyte materials have shown promise for applications in electric vehicles (EVs). However, understanding the effects of pro-cessing parameters on the ionic conductivity of these electrolytes is crucial for optimizing battery performance and manufacturing methods. This study investigates the influence of electrolyte op-erating temperature, electrolyte operating pressure, electrolyte pelletization pressure, and electro-lyte pelletizing temperature on the ionic conductivity of Li6PS5Cl0.5Br0.5 argyrodite electrolyte (AmpceraTM, D50=10 µm). A specially designed test cell is employed for the experimental meas-urements, allowing for controlled pelletization and testing within the same tooling. The results demonstrate the significant impact of the four parameters on the ionic conductivity of the argy-rodite electrolyte. The electrolyte operating temperature has a more pronounced effect than oper-ating pressure, and pelletizing temperature exerts a greater influence than pelletizing pressure. This study provides graphs that aid in understanding the interplay between these parameters and achieving desired conductivity values. It also establishes a baseline for the maximum pelletizing temperature before undesirable degradation of electrolyte occurs. By manipulating the pelletizing pressure, operating pressure, and pelletizing temperature, battery engineers can achieve the desired conductivity for specific applications. The findings emphasize the need to consider operating conditions to ensure satisfactory low-temperature performance, particularly for EVs. Overall, this study provides valuable insights into processing and operating conditions for ASSLBs utilizing Li6PS5Cl0.5Br0.5 argyrodite electrolyte.

Acute lymphoblastic leukemia (ALL) is a blood cancer that primarily affects children but also adults. It is due to the malignant proliferation of lymphoid precursor cells that invade the bone marrow and can spread to extramedullary sites. ALL is divided into B cell (85%) and T cell lineages (10 to 15%); rare cases are associated with the natural killer (NK) cell lineage (<1%). To date, the survival rate in children with ALL is excellent while in adults continues to be poor. Despite the therapeutic progress, there are subsets of patients that still have high relapse rates after chemotherapy or hematopoietic stem cell transplantation (HSCT) and an unsatisfactory cure rate. Hence, the identification of more effective and safer therapy choices represents a primary issue. In this review, we will discuss novel therapeutic options including bispecific antibodies, antibody-drug conjugates,chimeric antigen receptor (CAR)-based therapies, and other promising treatments for both pediatric and adult patients.

The COVID-19 pandemics has had an unprecedented global impact, and the COVID-19 mass vaccination campaign has been commonly regarded as crucial to overcome the pandemics. Since all-cause mortality is the best way to measure the consequences of a health intervention, the present study was devised to analyze the all-cause mortality data of the United Kingdom (UK), which are made publicly available broken down by vaccination status. Data from January to May 2022 were retrospectively collected and analyzed according to age groups and vaccination status and the relative risk (RR) for all-cause mortality was calculated in comparison to the corresponding unvaccinated groups. All-cause mortality RR was also calculated from January to May 2021 for vaccinated people. Results show that the all-cause mortality RR was higher in people who received one or two doses of COVID-19 vaccines throughout the whole period and in any of the age groups considered. People vaccinated with three doses more than 21 days earlier had RRs lower than unvaccinated people, which however linearly increased over time. RR in vaccinated people of all ages in comparison to unvaccinated people were lower in January-May 2021, however they steadily grew over time. The finding that all-cause mortality RR in vaccinated in comparison to unvaccinated people increases over time requires careful examination to understand the underlying factors. Meanwhile, all the other major countries should undertake a systematic collection of all-causes mortality broken down by vaccination status, and mass vaccination campaigns should be suspended.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

This work is devoted to the construction and study of commutative gates for a two-qubit quantum system. Using four-dimensional algebra developed by the Kazakh mathematician Abenov M.M. all groups of commutative gates have been constructed, and among all states of a two-qubit quantum system, unitary states with which a specific gate is connected have been identified. An explicit type of gate is described that transfers a quantum system from one unitary state to another unitary state. The proposed approach opens up new possibilities for the design of quantum algorithms not only for two-qubit quantum systems, but also for $n$-qubit quantum systems.

Video behavior recognition often needs to focus on object motion processes. In this work, a self-organizing computational system oriented to behavioral clustering recognition is proposed, which achieves the extraction of motion change patterns by binary encoding and completes motion pattern summarization using a similarity comparison algorithm. And in the face of unknown behavioral video data, a self-organizing structure with layer-by-layer accuracy progression is used to achieve motion law summarization by using a multi-layer agent design approach. Finally, the real-time feasibility is verified in the prototype system using real scenes to provide a new feasible solution for unsupervised behavior recognition and space-time scenes.

The problem of health status prediction of insulated-gate bipolar transistors (IGBTs) gains a lot of attention in the field of health management of power electronic equipment. The performance degradation of IGBT gate oxide layer is one of the important failure modes. In view of failure mechanism analysis and easy implementation of monitoring circuit, this paper selects the gate leakage current of IGBT as the precursor parameter of gate oxide degradation, and uses time domain characteristic analysis, gray correlation degree, Mahalanobis distance, Kalman filter and other methods to carry out feature selection and fusion, and finally obtains a health indicator characterizing the degradation of IGBT gate oxide. Based on the Convolutional Neural Network and Long Short-Term Memory (CNN-LSTM) network, this paper constructs an IGBT gate oxide degradation prediction model, and performs experimental analysis on the dataset released by NASA-Ames Laboratory, and the average absolute error of performance degradation prediction is as low as 0.0216. Compared with Long Short-Term Memory (LSTM), Convolutional Neural Network (CNN), Support Vector Regression (SVR) and CNN-LSTM models, CNN-LSTM network has the highest prediction accuracy. These results show the feasibility of gate leakage current as a precursor parameter of IGBT gate oxide layer failure, as well as the accuracy and reliability of the CNN-LSTM prediction model.

Large epidemiological studies show U-shaped relationships between high-density lipoprotein cholesterol (HDL-C) levels and all-cause mortality in individuals without atherosclerotic cardiovascular diseases (ASCVD). Association in those with ASCVD by sex is unclear. We examined the association between HDL-C levels and 10-year all-cause mortality in subjects (≥40 years of age) with ASCVD using the 2010 National Health Insurance Service and the National Death Registry of Korea. We categorized HDL-C levels into three groups (low: <40 mg/dL for males, <50 mg/dL for females; high: 40-90 mg/dL for males, 50-90 mg/dL for females; extremely high: >90 mg/dL) and 10 mg/dL intervals. We conducted a sex-stratified and adjusted Cox proportional hazards analysis. Out of 1,711,548 individuals (54% female, mean age 61.4 years), 10-year mortality was observed in 218,252 (12.8%). Males had a higher mortality rate than females (16.2% vs 9.8%; P<0.001). When adjusting for age, body mass index, LDL-cholesterol, triglycerides, hypertension, diabetes, smoking, and alcohol consumption, the low and extremely high HDL-C groups had significantly higher hazard ratios for 10-year mortality compared to the high HDL-C group in males [1.183 (1.166-1.199), 1.359 (1.288-1.434)] and in females [1.153 (1.138-1.169), 1.095 (1.029-1.167)]. The frequency distribution bars for the 10-year mortality rate showed sex-specific nadirs of 50-59 mg/dL in males and 70-79 mg/dL in females. In this ASCVD cohort, the extremely high HDL-C (>90 mg/dL) group had 35.9% and 9.5% higher 10-year mortality risk than the high HDL-C group for males and females, respectively. There was a slightly U-shaped relationship between baseline HDL-C levels and 10-year mortality rate, with earlier inflection in males than in females.

This study updates previous research showing that 22 all-cause mortality in 31 European countries increased over time the higher the 21 COVID-19 full vaccination uptake. The update illuminates that a one percentage point increase in 21 full vaccination uptake initially decreased all-cause mortality from Jan to Mar 22 by –0.423 percent (95% CI –0.577, –0.270), but the following 14 months, a one percentage point increase in 21 booster vaccination uptake oppositely increased mortality by 0.366 percent (95% CI 0.250, 0.482). The findings indicate that full vaccination initially prevented mortality, but subsequently, booster vaccination, in particular, detrimentally and consistently induced higher mortality. The effects remained robust when controlling for alternative explanations. Studies have argued that heat waves caused mortality in the 22 summer and energy prices caused mortality in the 22-23 winter. However, the update shows that booster vaccination consistently induced higher mortality when neither heat waves nor energy prices were likely explanations.

Although CAD/CAM ceramics present a promising alternative to metal-ceramic fixed dental prostheses, little is known about their mid- and long-term clinical performance. This systematic review aims to estimate the survival and success rates and describes the underlying complication characteristics for CAD/CAM tooth-supported fixed dental prostheses (FDPs). We systematically searched MEDLINE and Web of Science to find relevant prospective studies with a follow-up of at least one year. We estimated pooled 1-, 5- and 10-year survival and success rates by combining the collected data in a Poisson regression model. Descriptive statistics were conducted to evaluate the distribution of failures and complications in the included studies. Risk of bias for the included studies was assessed with an adapted checklist for single-arm trials. Pooled estimated 1-, 5-, and 10-year survival rates ranged from 93.80% to 94.66%, 89.67% to 91.1%, and 79.33% to 82.20%, respectively. The corresponding success rates, excluding failures but including any other types of intervention, were 94.53% to 96.77%, 90.89% to 94.62%, and 81.78% to 89.25%. Secondary caries was the most frequent cause of failure, followed by chipping of the veneering. The most common cause of complication, excluding failures but requiring intervention, was chipping of the veneering. Risk of bias was generally acceptable for the included studies, with 7 studies associated with low risk of bias, 8 studies with a moderate risk of bias, and 3 studies with serious risk of bias. The current meta-analysis on CAD/CAM supported FDPs revealed satisfying survival and success rates for up to 10 years of exposure. More prospective studies focusing on long-term performance are needed to strengthen the evidence currently available in the literature.

Long non-coding RNA (lncRNA) aberrant expression have been found in several types of cancer, including acute lymphoblastic leukemia (ALL), but lncRNA mapped in transcribed ultraconserved regions (T-UCRs) are little explored. The T-UCRs uc.112, uc.122, uc.160 and uc.262 were evaluated in pediatric ALL and uc.112 expression was higher in T-ALL compared to patients with B-ALL and in patients with hyperdiploid karyotype. These findings suggest a potential role of this uc.112 in pediatric ALL and emphasize the need for further investigation of T-UCR in pediatric ALL.

Achieving water security and availability for all is the main agenda of the UN-Sustainable Development Goals by the year 2030. To achieve the goal of water secure future in rapidly urbanizing cities, the sustainable water supplies are necessary. In the western part of India, the city of Surat is continuously growing and rapidly urbanized, which exerting massive pressure on groundwater water supply to meet increasing water demands. The study adopted the investigative approach, in which a total 33 groundwater samples were collected in and around the city from open, bore and dug wells and hand pumps. The selection of sampling sites was based on the land use signature, areas with a different depth of aquifers and different geological formations. After the hydrogeochemical analysis, the study evaluated the present state of the groundwater quality and determined the spatial distribution of groundwater quality parameters such as hardness, electrical conductivity, Cl −, pH, SO42-, and NO3 −  concentrations. An interpolation technique, known as ordinary kriging, was used to acquire the spatial distribution of parameters of groundwater quality parameters. The result showed that the groundwater quality falls under class I (>25%) and class II (25 to75%) category. The study recommends that the groundwater in the study area is not suitable for potable purposes, especially without any improved onsite water treatment facilities but it is appropriate for the irrigation purposes in City.

In this paper, the single event burnout(SEB) and reinforcement structure of 1200V SiC MOSFET (SG-SBD-MOSFET) with split gate and schottky barrier diode(SBD) embedded were studied. The device structure was established using Sentaurus TCAD, and the transient current changes of single event effect(SEE), SEB threshold voltage, as well as the regularity of electricfield peak distribution transfer were studied when heavy ions were incident from different regions of the device. Based on SEE analysis of new structural device, two reinforcement structure designs for SEB resistance were studied, namely the expansion of P+body contact area and the design of multi-layer N-type interval buffer layer. Firstly, two reinforcement schemes for SEB were analyzed separately, and then comprehensive design and analysis were carried out. The results showed that the SEB threshold voltage of heavy ions incident from the N+source region was increased by 16% when using the P+body contact area extension alone; When the device is reinforced with multi-layer N-type interval buffer layer alone, the SEB threshold voltage increases by 29%; The comprehensive use of P+body contact area expansion and multi-layer N-type interval buffer layer reinforcement increased the SEB threshold voltage by 33%. Overall, the breakdown voltage of the reinforced device decreased from 1632.935V to 1403.135V, which can be seen as reducing the remaining redundant voltage to 19%. The device performance was not significantly affected.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

The status of vegetation and the impacts of mammalian herbivores on rangelands are complex, and such studies in Kenya are scanty. We investigated the dynamics of ground cover vegetation in Hell’s Gate National Park in relation to mammalian herbivory. Removal of palatable vegetation is postulated to enhance the development of invasive plant species. We investigated the influence of mammalian herbivores on vegetation diversity and dynamics in this rangeland. Three sampling blocks approximately 3 Km apart measuring 100 m x 50 m were established, each divided into three belt-transects (100 m x 10 m), and separated by a 10 m buffer zone. 2 m by 2 m quadrats at 20 m intervals were established in each transect. We measured composition the richness of plant and mammal species, and herbivory levels four times for six months (September 2018 to February 2019). Plant cover (P&lt; 0.001) and species diversity (P&lt; 0.001) differed significantly among sampling blocks and between seasons (P&lt; 0.001). Non-metric multidimensional scaling of plant species and herbivores showed co-occurrence of Zebras with Sida tenuicarpa and giraffes with Solanum incunum. We conclude that the removal of preferred plants through herbivory may be giving an edge to invasive species in the park.

The gate resistance is a parasitic element in transistors for RF and millimeter-wave circuits that can negatively impact power gain and noise figure. To develop accurate device models, a reliable measurement methodology is crucial. This article reviews the standard measurement methodology used in the literature and proposes also an additional method, which is evaluated using suitable test structures in a 16nm FinFET process. The advantages and disadvantages of the two approaches are discussed along with their respective application scenarios

Two opposed p–n diodes are connected with another junction that causes cancellation of the electric field in the depletion layer of each diode by the field of the other diode. This derived quantum diode is called the A system. Another dual diode, constructed by the same process but with the p- and n-types positioned as duality, called the B system. When a bias voltage is applied between the A and B systems, Lorentz conservation imparts a momentum (i.e., a wave number) to the carriers in the absence of any internal voltage. Thus, a superconducting bias current density appears without the need for cooling. The reappearances of electron–hole pairs on the junction surfaces are assumed to be described by entire wavefunctions normalized by the band gap. Based on the bias superconducting current, NOT and NAND gates were constructed from the quantum diode systems. Numerical calculations revealed that the constant phases of the entire wavefunctions of the p-and n-types converged. Accordingly, it was clarified that Bose–Einstein condensation and the Meissner effect (described by the London equation) occurred in the quantum diode systems. Moreover, the systems exhibited rectification characteristics and a switching speed of the order of 10^-14 s. Combining this switching property with the large bias superconducting current (of the order of several V), we developed NOT and NAND gates with direct quantum correlations among many qubits, which are unaffected by random and thermal noises. These gates have memorization and initialization properties and are compatible with existing and accumulating programing algorithms. Moreover, when harvesting a divergent current output from these systems, the bias superconducting current and memorization property preserve the formed quantum correlations.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

Abstract The hallmark of acute promyelocytic leukemia (APL) is the presence of the characteristic fusion transcript of the promyelocytic leukemia gene with the retinoic acid receptor α gene (PML::RARA), which is a molecular target for all-transretinoic acid (ATRA) and arsenic trioxide (ATO). Therapies with ATRA plus ATO have excellent outcomes in terms of complete remission rate, overall survival, and achievement of a deep and durable molecular response with a very low incidence of relapse. However, although the combination of ATRA and ATO has lower hematologic toxicity than standard chemotherapy, its use is associated with a spectrum of unique toxicities, such as hepatic toxicity, QTc (QT interval corrected) prolongation, neurotoxicity, and differentiation syndrome. Hematologists treating patients with acute promyelocytic leukemia should be aware of possible early-complications of the ATRA plus ATO regimen and aim to balance treatment-related adverse events and efficacy. Careful follow-up of the patient’s clinical course is essential to identify and treat each complication. This study focused on treatment-related complications during induction and consolidations in patients with APL who received ATRA plus ATO. We retrospectively analyzed 26 adult patients diagnosed with APL between 2019 and 2022 at our center to identify the incidence rate, severity and time of onset of short-term non-hematologic adverse events relative to the initiation of the ATRA and ATO regimen. Additionally, we review the existing literature regarding the toxic side effects of ATO in APL and discuss how its most frequent toxicities should be managed. The median follow-up of our patients was 21.5 months (range, 1-48 months) and the most common adverse events were hepatic toxicity (69.2%), infections (46.1%), differentiation syndrome(23%) and QT prolongation (11.5%). All patients experienced at least one adverse event and grade 3 and 4 toxicities occurred in 57.6 % patients; these generally consisted of liver enzyme elevations, QTc prolongation, but also some rare manifestations such as musculoskeletal pain syndrome (1 patient) and ATO-related pancreatitis (1 patient). Most patients developed side-effects during induction. This is the first study about Romanian patients diagnosed with APL. Our results suggest that all treatment-related adverse events, except for differentiation syndrome are manageable, self-limiting and reversible. All patients, except for two (one died during induction and one died during consolidation), were able to complete the treatment consolidation with ATO and ATRA.

The results of measuring the capacity of a thin-film solid-state lithium-ion battery (SSLIB) Ti|Si@O@Al|LiPON|LiCoO₂|Ti at different charge currents are reported. It is shown that the dependence of the capacity on the current density follows the Peukert's law, which is characterized by a low value of the Peukert’s exponent in the region of low currents and a high value of the exponent in the region of high currents. A capacity model for a SSLIB based on the balance of diffusion and migration currents is proposed and the dependence of the capacity on the charge current is derived. The obtained dependence is well approximated by Peukert's law with an exponent of 1.39, which is intermediate between the exponents for lithium-ion batteries with liquid electrolyte and SSLIBs.

Beef has one of the highest climate footprints of all foods, and therefore the hamburger has been targeted for substitution by numerous plant-based alternatives. However, many consumers find the taste of these alternatives lacking, and thus we proposed a hybrid meat and plant-based burger as a lower threshold alternative for these consumers. The burger was made from 50% meat (beef and pork, 4:1) and 50% plant-based ingredients, including texturised legume protein and had a climate footprint less than half that of a beef burger. Texture and sensory properties were evaluated instrumentally and through a consumer survey (n = 381) using the check-all-that-apply (CATA) method. Moisture properties indicated a significantly juicier eating experience for the hybrid compared to a beef burger, which was supported by the CATA survey. From texture profile analysis the hybrid burger was significantly softer and less cohesive than a beef burger. Despite having different CATA term profiles overall liking of the hybrid and a beef burger were not significantly different. Penalty analysis indicated that “meat flavour”, “juiciness”, “spiciness”, and “saltiness” are the most important attributes for a burger. In conclusion, consumers may be open to reducing their meat consumption by way of hybrid meat and plant-based products.

Reliable motor control design is a critical part of the electric vehicle application. Control techniques and motor control devices play an important role in achieving system reliability. In this study, motor control devices have been proposed to implement control techniques in sensorless PMSM. Motor control devices including PWM signal generation by FPGA, gate driver circuit (GDC), and power inverter were developed to be integrated into single-stage motor control devices for sensorless motor control applications. Improvements in GDC design have been the focus to increase the performance of the motor control devices used. Switching losses due to the parasitic elements caused ringing switching behavior of the power inverter circuit, which reduces the performance when the system is integrated. Moreover, in the implementation of sensorless motor control using observer techniques, these conditions affect the accuracy of rotor position estimation, which uses the current or voltage information of the power converter as a variable in the observer design model. Therefore, a GDC design using IR2110 with additional ringing suppression circuit configuration was proposed for the application of motor device control topology to improve the performance of sensorless motor control system. Furthermore, the reduction of switching losses, reduction of current distortion, and accuracy of rotor position information were confirmed by experimental results.

With the current technological transformation in the automotive industry, autonomous vehicles are getting closer to the Society of Automative Engineers (SAE) automation level 5. This level corresponds to the full vehicle automation, where the driving system autonomously monitors and navigates the environment. With SAE-level 5, the concept of a Shared Autonomous Vehicle (SAV) will soon become a reality and mainstream. The main purpose of an SAV is to allow unrelated passengers to share an autonomous vehicle without a driver/moderator inside the shared space. However, to ensure their safety and well-being until they reach their final destination, it is required an active monitoring of all passengers. In this context, this article presents a microphone-based sensor system that is able to localize sound events inside an SAV. The solution is composed of a Micro-Electro-Mechanical System (MEMS) microphone array with a circular geometry connected to an embedded processing platform that resorts to Field-Programmable Gate Array (FPGA) technology to successfully process in hardware the sound localization algorithms.

This work - in two parts - tries to promote a new method in Mathematical Modeling, not ever used before, namely the use of the methods of Non-standard Analysis in Topoi. For the general mathematical theory of topoi (Topoi Theory) we refer to the book [10] . For non-standard analysis in the particular Boolean topos SET (the category of sets) we refer to the book [11]. This first part of the work is related, from an applicative point of view, mainly with Mathematical Neuroscience, more precisely a model of the human thinking, consciousness and subconsciousness. The connections between brain and mind will be also scketched, but a closer study also need some further topics to be studied in Part II: Artificial Intelligence, namely (Quantum) neural networks and (Quantum) Turing machine. However both parts (I. and II.) should be considered together, because they complement each other. The topoi model the intuitionistic logic (multi-valued) and have been used in Quantum Physics (see [9] and its references) while Non-Standard Analysis in SET (introduced by Abraham Robinson[31]) has been applied in Mathematical Economics (see [2] and its references); however, the combination was never used until now in Applied Mathematics. Even more, the Non-standard Analysis in Topoi is not too much studied from the point of view of Pure Mathematics either. One of the main objective of this work is to produce progress in this aria of Mathematics also, mainly for the SET-type topoi and exponential topoi, those topoi used in Quantum Physics and in which we need Non-stantard Analysis for our purposes. Based on the paper [13] we propose the logic of non-standard extensions in topoi as a model of the human thinking (based on infons), these theories representing top and very difficult results in Abstract Mathematics. We will analise the relation between brain and mind via the genetic-epigenetic interplay. More details will be provided in the Introduction, followed by a short presentation of the general theory, later connected with the (Quantum) Yang-Baxter equations in topoi. The connections between these equations and braid groups and knots, with intended applications in Neuroscience and Artificial Intelligence will be further analysed in Part II. Besides promoting a new idea of modeling, the present paper aims to promote the building of a Research Proposal for the European $''$Human Brain Project$''$ (https://www.humanbrainproject.eu/en/), and the NSF-Europe Program $''$Collaborative Research in Computational Neuroscience$''$ (https://www.nsf.gov/funding/pgm\_summ.jsp?pims\_id=5147), jointly with the new founded $''$National Centre for the Research of the Brain$''$ of the Romanian Academy of Science (https://acad.ro/centreAR/CNCC/CNCC.pdf, in Romanian). $''$Blue Brain Project$''$ (https://www.epfl.ch/research/domains/bluebrain/) could also be of big interest. We hope that the journals edited by MDPI (Axioms, in particular) and by the Simion Stoilow Institute of the Romanian Academy - Revue Roumaine de Mathematique Pures et Appliqu (http://imar.ro/journals/Revue\_Mathematique/home\_page.html) - among others - will host special issues related to the research subjects described in both parts of this work, starting with this one. For further details and some of the progress on this research subject, see www.ovidiufpasarescu.com.}

The synthesis and structure of the 4,4′-dipyridyl N,N′-donor ligand with a central thiazolo[5,4-d]thiazole (tztz) unit, named Dptztz is presented. With the linker Dptztz and isophthalate (benzene-1,3-dicarboxylate, 1,3-BDC²⁻) the mixed-linker, two-dimensional coordination network [Zn(1,3-BDC)Dptztz]·DMF could be obtained (DMF = dimethylformamide), which belongs to the class of coordination polymers with interdigitated structures (CIDs). The incorporated DMF solvent molecules can be removed through solvent exchange and evacuation such that the supramolecular 3D packing of the 2D networks retains porosity for CO₂ adsorption in activated [Zn(1,3-BDC)Dptztz]. The first sorption study of a tztz-functionalized porous metal-organic framework material yields a BET surface of 417 m²/g from CO₂ adsorption. The heat of adsorption for CO₂ exhibits a relative maximum with 27.7 kJ/mol at adsorbed CO₂ of about 4 cm³/g STP which is interpreted as a gate-opening effect.

Current Li battery technology employs graphite anode and flammable organic liquid electrolytes. Thus, current Li battery is always facing the problems of low energy density and safety. Additionally, sustainable supply of Li due to scarce abundance of Li sources is another problem. All-solid-state Mg battery is expected to solve the problems owing to non-flammable solid-state electrolytes, high capacity/safety of divalent Mg metal anode and high abundance of Mg sources. Therefore, solid-state electrolytes and all-solid-state Mg battery have been researched intensively last two decades. However, realization of all-solid-state Mg battery is still far. In this article, we review recent research progress on all-solid-state Mg battery so that researchers can pursue recent research trend of all-solid-state Mg battery. At first, solid-state electrolyte research is described briefly in the categories of inorganic, organic and inorganic/organic composite electrolytes. After that, the recent research progress of all-solid-state Mg battery is summarized and analyzed. To help readers, we tabulate electrode materials, experimental conditions and performances of all-solid-state Mg battery so that the readers can find necessary information at a glance. In the last, challenges to realize the all-solid-state Mg batteries are visited.

Intergenerational integration has given rise to a novel aging paradigm known as all-age communities, which is garnering international attention. In China, the aging population and the implementation of the three-child policy have resulted in increased demand for retirement and childcare services among residents in older neighborhoods. Consequently, there is a pressing need to retrofit these older neighborhoods to accommodate all-age living arrangements given the high demand they generate. Therefore, this study undertakes research interviews with residents and constructs an exploratory theoretical model rooted in established theory. To assess the significance of our model, we employ Smart PLS 3.0 based on 297 empirical data points. Our findings indicate that anxiety has a significant negative effect on payment behavior; objective perception, willingness to pay, and government assistance exert significant positive effects on payment behavior. By comprehensively analyzing the mechanisms underlying residents’ payment behavior, this study provides valuable insights to the government for promoting the aging process within communities and formulating effective transformation policies.

The cancelation factor (CF) is a model for the ratio between gravity wave perturbations in the airglow intensity to that in the ambient temperature. The CF model allows to estimate the momentum and energy flux of gravity waves seen in nightglow images as well as the divergence of these fluxes due to waves propagating through the mesosphere and lower thermosphere region, where the nightglow and the Na layers are located. This study uses a set of T/W Na Lidar data and zenith nightglow image observations of the OH and O(1S) emissions to test and validate the CF model from the experimental perspective. The dataset analyzed was obtained during campaigns carried out at the Andes Lidar Observatory (ALO), Chile in 2015, 2016, and 2017. The CF modeled function was compared with observed points from an empirical method for vertically propagating waves that calculates directly the ratio of the gravity wave amplitude seen in nightglow images to the wave amplitude seen in lidar temperatures. We show that the CF analytical relationship underestimates the observed results generally. However, the O(1S) emission line has better agreement respect to the theoretical value due to simpler nightglow photochemistry. In contrast, the observed CF ratio from the OH emission deviates by a factor of two from the modeled asymptotic value.

Amplitude growth rates of monochromatic gravity waves were estimated and compared from multiple instrument measurements carried out in Brazil. Wave dynamic parameters were obtained from sodium density profiles from lidar observations carried out in Sao Jose dos Campos (23°S, 46°W), while all-sky images of multiple airglow layers provided amplitudes and parameters of waves over Cachoeira Paulista (23°S, 45°W). Growth rates of gravity wave amplitudes from lidar and airglow imager data were consistent with dissipative wave behavior. Only a small amount of the observed wave events presented freely propagating behavior. Part of the observed waves presented saturated amplitude. The general saturated/damped behavior is consistent with diffusive filtering processes imposing limits to amplitude growth rates of the observed gravity waves.

In this paper, we present a high-speed, unified elliptic curve cryptography (ECC) processor for arbitrary Weierstrass curves over GF(p), which to the best of our knowledge, outperforms other similar works in terms of execution time. Our approach employs the combination of the schoolbook long and Karatsuba multiplication algorithm for the elliptic curve point multiplication (ECPM) to achieve better parallelization while retaining low complexity. In the hardware implementation, the substantial gain in speed is also contributed by our n-bit pipelined Montgomery Modular Multiplier (pMMM), which is constructed from our n-bit pipelined multiplier-accumulators that utilizes DSP primitives as digit multipliers. Additionally, we also introduce our unified, pipelined modular adder/subtractor (pMAS) for the underlying field arithmetic, and leverage a more efficient yet compact scheduling of the Montgomery ladder algorithm. The implementation on the 7-series FPGA: Virtex-7, Kintex-7, and XC7Z020, yields 0.139, 0.138, and 0.206 ms of execution time, respectively. Furthermore, since our pMMM module is generic for any curve in Weierstrass form, we support multi-curve parameters, resulting in a unified ECC architecture. Lastly, our method also works in constant time, making it suitable for applications requiring high speed and SCA-resistant characteristics.

We primarily study a possible link between 2021 COVID-19 vaccination uptake in Europe and monthly 2022 excess all-cause mortality, i.e., mortality higher than before the pandemic. Analyses of 31 countries weighted by population size show that all-cause mortality during the first nine months of 2022 increased more the higher the 2021 vaccination uptake; a one percentage point increase in 2021 vaccination uptake was associated with a monthly mortality increase in 2022 by 0.105 percent (95% CI, 0.075-0.134). When controlling for alternative explanations, the association remained robust, and we discuss the result emphasizing causality as well as potential ecological fallacy. Also, the study shows that 2021 all-cause mortality was lower the higher the vaccination uptake, but this association became non-significant when controlling for alternative explanations.

Since identified as the pathogen responsible for an outbreak of severe respiratory distress in Wuhan, China, the 2019-nCoV coronavirus has caused over 30M cases and 1M deaths globally. Sporadic cases were identified in several states in the US from early January, and large-scale community transmission is believed to have started in late February, leading to a first spike in COVID-19 deaths and overall mortality in late April, and a second spike later in the summer. I show here that the dynamics of the pandemic were different in different regions of the US, showing a north-south pattern, with a first pandemic wave mainly in northern regions, followed by a second wave mainly in southern regions. Analysis of overall mortality data shows that the increase in mortality correlates well with COVID-19 incidence in most regions, and that from April through August COVID-19 deaths accounted for a substantial proportion of all deaths in all parts of the US.

We present in this work a method for estimation of plasma bubble mean zonal drift velocities using keograms generated from images of the OI 6300.0 nm nightglow emission collected from an equatorial station -- Cariri (7.4$^\circ$S, 36.5$^\circ$W), and a mid-latitude station -- Cachoeira Paulista (22.7$^\circ$S, 45$^\circ$W), both in the Brazilian sector. The mean zonal drift velocities were estimated for 239 events recorded from 2000 to 2003 in Cariri, and for 56 events recorded over Cachoeira Paulista from 1998 to 2000. It was found that plasma bubble zonal drift velocities are smaller ($\sim$60 ms$^{-1}$) for events occurring later in the night compared to those occurring earlier ($\sim$150 ms$^{-1}$). The decreasing rate of the zonal drift velocity is of $\sim$10 ms$^{-1}$/h. We have also found that, in general, bubble events appearing first in the west-most region of the keogram are faster than those appearing first in the east-most region of the keograms. Larger zonal drift velocities occur from 19 LT to 23 LT in a longitude range from 37$^\circ$ to 33$^\circ$. The method of velocity estimation using keograms compares favorably against the mosaic method developed by \cite{Arruda:2005}, but the standard deviation of the residuals for the zonal drift velocities from the two methods is $\sim$15 ms$^{-1}$

Polyamides (PAs) are one of the most important engineering polymers; however, the difficulty in dissolving them hinders their applications. Formic acid (FA) is the most common solvent for PAs, but it has industrial limitations. In this contribution, we proposed a new solvent system for PAs by replacing a portion of the FA with urea and calcium chloride (FAUCa). Urea imparts the hydrogen bonding and calcium ion from the calcium chloride, as a Lewis acid was added to the system to compensate for the pH decrease due to the addition of urea. The results showed that the proposed solvent (FAUCa) could readily dissolve PAs, resulting in less decrease in the mechanical properties during the dissolution. The composite prepared using the FAUCa has almost the same properties like the one prepared using the FA solution. The solution was applied on a polyamide 66 fabric to make an all-polyamide composite coated-fabric, which then was characterized. The FAUCa solution had a higher viscosity than the one prepared using the neat FA solvent, which can be an advantage in the applications which needs higher viscosity like preparing the all-polyamide composite coated-fabric. A more viscouse solution makes a denser coating which will increase the water-/gas-tightness. In conclusion, using the FAUCa solvent has two merits: 1. replacement of 40 % of the FA with less harmful and environmentally-friendly chemicals and 2. enabling for the preparation of more viscouse solutions, which makes denser coating.

An all-dielectric metasurface composed of orthogonal-slit silicon disks is proposed in this study. By modifying the unit structure of the metasurface with the bound states in the continuum (BIC) theory, a sharp Fano resonance can be generated. The resonance properties of the metasurface are investigated by analyzing the effects of the structural parameters on the resonance using the eigenmode analysis method. The Q factor and the resonance wavelength can be adjusted by varying the slit width, the disk thickness, and the disk radius. The electromagnetic characteristics and mechanism of the toroidal dipole-BIC (TD-BIC) are explored in depth through an analysis of the multipole expansion of the scattered power, along with the electromagnetic field and the current distribution at resonance. This research provides a novel approach for excitation of a strong TD-BIC resonance and proposes potential applications in optical switches, high-sensitivity optical sensors, and related areas.

Since the 21st century, China's urbanization process has been rapid development, the concept and function of urban public space in the city has been gradually paid attention to. In order to guarantee life and water, most urban construction relies on rivers, and Bridges are the most important way to communicate between urban areas. The main functional part of the bridge is the span structure, that is, the bearing structure of the bridge, and the lower part of the "gray" space formed by the bridge structure. Considering the social level, with the economic growth and urbanization development, people have brought a better living environment and quality of life, and also improved the requirements for urban public environment. In the increasingly tense urban space, how to use and transform the space under the bridge is a problem that needs to be considered and solved. In view of this problem, in this study, we try to solve the micro-transformation of space under Bridges in cities through public art from the perspective of "regional culture" and "art for all". This paper analyzes the micro-transformation of space art under Bridges in two large cities of Shanghai and Foshan, namely, the space under Bridges under Songhong Road in Shanghai, the space under Bridges under Central Of Suzhou River and the space under Bridges under Pingsheng Bridge in Foshan. This paper discusses the cultural intervention of "regional culture" in the micro-transformation of the space under the bridge, and the influence and effect of "art for all" on the public art space under the bridge after the transformation to the community and the public.

Background: All Payer Claims Databases (APCD) are a rich source of health information, however, race and ethnicity (R&E) data are largely missing. Bayesian Improved Surname Geocoding (BISG) is a common R&E imputation method, yet, validation of BISG in APCDs is lacking. We used the BISG to impute missing R&E in the Oregon APCD. Methods: BISG imputed R&E for Asian Pacific Islanders (API), Blacks, Hispanics and Whites were contrasted to the gold standard (vital statistics) and sensitivity and specificity improvements were assessed. Logistic regression examined whether missing R&E was random across patient characteristics. Results: Among 85,857 individuals in the study, 32.1% (n=27,594) had missing R&E. Missing R&E was not randomly distributed. There were higher odds of missingness among males, Whites, those age 65 and older, and commercially insured individuals. Differences in the percent missing were also found by co-morbid conditions and mortality causes. Imputing the missing R&E with BISG method improved the sensitivity to identify White, Black, API, and Hispanics. Conclusions: APCDs can benefit from enhancing missing R&E with BISG imputation to perform more robust population-health level analyses and identify inequities according to R&E without losing power or dropping non-random records with missing R&E data.

The development of electric aircrafts is becoming an important technology for achieving the goals set by the European Commission for the reduction of gases emissions by 2050 in the aeronautical transportation system. However, there is a gap between the values of specific power in commercial electric machines and the ones required for aeronautical applications. Therefore, the search for alternative materials and non-conventional designs is mandatory. One emergent solution is using superconducting machines and systems to overcome the current limits of conventional electrical machines. This work reviews the new hybrid and all-electric aircraft tendencies, complementing it with recent research on the design and development of high specific power superconducting machines. This includes the main topologies for hybrid and all-electric aircraft, with an overview of the ongoing worldwide projects of these types of aircrafts, systematizing the main characteristics of their propulsion systems. It also includes the research on superconducting machines for the purpose of high specific power, considering the impact on the redesign of aircraft systems in the electrical, cooling, and fuel source sense.

Total cloud cover (TCC) retrieval from ground-based optical imagery is a problem being tackled by a few generations of researchers. The number of human-designed algorithms for the estimation of TCC grows every year. However, there is not very much progress in terms of quality, mostly due to the lack of systematic approach to the design of the algorithms, to the assessment of their generalization ability, and to the assessment of the TCC retrieval quality. In this study, we discuss the optimization nature of data-driven schemes for TCC retrieval. In order to compare the algorithms, we propose the framework for the assessment of the algorithms characteristics. We present several new algorithms that are based on deep learning techniques: a model for outliers filtering, and a few models for TCC retrieval from all-sky imagery. For training and assessment of data-driven algorithms of this study, we present the Dataset of All-Sky Imagery over the Ocean (DASIO) containing over one million of all-sky optical images of visible sky dome taken in various regions of the World Ocean. The research campaigns contributed to DASIO collection took place in the Atlantic ocean, the Indian ocean the Red and Mediterranean seas, and also in the Arctic ocean. Optical imagery collected during these missions are accompanied by standard meteorological observations of cloudiness characteristics made by experienced observers. We assess the generalization ability of the presented models in several scenarios that differ in terms of the regions selected for the train and validation subsets. As a result, we demonstrate that our models based on convolutional neural networks deliver superior quality compared to all previously published schemes. As a key result, we demonstrate considerable drop of the ability to generalize the training data in case of strong covariate shift between training and validation subsets of imagery which may take place in case of region-aware subsampling.

Advanced image processing will be crucial for emerging technologies such as autonomous driving, where the requirement to quickly recognize and classify objects under rapidly changing, poor visibility environments in real time will be needed. Photonic technologies will be key for next-generation signal and information processing, due to their wide bandwidths of 10’s of Terahertz and versatility. Here, we demonstrate broadband real time analog image and video processing with an ultrahigh bandwidth photonic processor that is highly versatile and reconfigurable. It is capable of massively parallel processing over 10,000 video signals simultaneously in real time, performing key functions needed for object recognition, such as edge enhancement and detection. Our system, based on a soliton crystal Kerr optical micro-comb with a 49GHz spacing with >90 wavelengths in the C-band, is highly versatile, performing different functions without changing the physical hardware. These results highlight the potential for photonic processing based on Kerr microcombs for chip-scale fully programmable high-speed real time video processing for next generation technologies.

late in December 2019 2019-nCoV was identified as the pathogen responsible for an outbreak of severe respiratory distress in Wuhan, China. The virus was detected in multiple countries during January, but it is believed widespread community transmission began late in February or early March. Since March the virus has caused over 100k confirmed deaths in the US, with some states more severely impacted, notably NY and NJ. Here I examine excess mortality at the national and state level from January through July 2020. I find that the increase in excess mortality began in late February, suggesting the pathogen was circulating undetected earlier than assumed. The timing and intensity of the increase in excess mortality varied across states, with two patterns emerging: an early, sharp increase reaching a peak during April-May, best exemplified by NY and NJ, and a shallower, sustained increase, reaching a peak in late July, observed mostly in the southern regions of the US.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

The importance and near ubiquity of the Golden Ratio in disciplines like chemistry and biology is well known, but only recently has it come to light in areas pertaining to the Quantum domain. By using a modified tool-kit of hyper-complex numbers (known as Dimensional Gate Operators) and numerical analysis, we uncover a connection between hyper-dimensional objects, the Fibonacci sequence and that of quasiparticles and excitations. The results show that dimensionality increases in step with the Fibonacci sequence.

Recently L-shaped tunneling field-effect-transistor (LTFET) has been introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, shortcoming of LTFET was investigated. It was found that corner effect present in LTFET effectively degrades its subthreshold slope. To get rid of corner effect a new type of device with dual material gates is presented. The new device termed as DG-LTFET gets rid of the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over LTFET. In this work DG-LTFET was evaluated for different device parameters, and bench-marked against LTFET. This work presents an optimum configuration of DG-LTFET in terms of device dimensions and doping levels, to get the best subthreshold, ON current and ambipolar performance from the DG-LTFET.

Since 2020 COVID-19 has caused serious mortality around the world. Given the ambiguity in es-tablishing COVID-19 as the direct cause of death we first investigate the effects of age and sex upon all-cause mortality during 2020 and 2021 in England and Wales. Since infectious agents have their own unique age profile for death, we explore several methods to adjust single year of age deaths in England and Wales during 2019 (the pre-COVID-19 base year) to a pathogen-neutral single year of age baseline. This adjusted base year is then used to confirm the widely reported higher deaths in males for most ages above 43 years in both 2020 and 2021. During 2020 (+ COVID-19 but no vac-cination) both male and female population-adjusted deaths were significantly increased above age 35. A significant reduction in all-cause mortality among both males and females aged 75+ could be demonstrated in 2021 during widespread COVID–19 vaccination, however, below age 75 deaths progressively increased. This finding arises from a mix of vaccination and year of age profiles of deaths for the different SARS-CoV-2 variants. In addition, specific effects for age around puberty were demonstrated where females had higher deaths rather than males. There is evidence that year-of-birth cohorts may also be involved, indicating that immune priming to specific pathogen outbreaks in the past may lead to lower deaths for some birth cohorts. To specifically identify the age profile for the COVID-19 variants in 2020 to 2023, we employ the proportion of total deaths at each age which are potentially due to or ‘with’ COVID-19. The original Wuhan strain, and the Alpha variant show somewhat limited divergence in the age profile with the Alpha variant shifted to a moderately higher proportion of deaths below age 84. The Delta variant specifically targeted persons below age 65. The Omicron variants showed significantly lower proportion of overall mortality, with markedly higher relative proportion of deaths above age 65 steeply increasing with age to a maximum around 100 years of age. A similar age profile for the variants can be seen in the age-banded deaths in US states – although slightly obscured by using age bands rather than single year of age. However, the US data shows that higher male deaths are greatly dependent on age and the COVID-variant. Deaths determined as ‘due to’ COVID-19 (as opposed to ‘involving’ COVID-19) in England and Wales were especially over-estimated in 2021 relative to the change in all-cause mortality. This arose as a by-product of an increase in COVID-19 testing capacity in late 2020. Potential structure-function mechanisms for the year of age specificity of SARS-CoV-2 var-iants are discussed. The question is posed as to whether vaccines based on different variants carry the specific age profile through into the vaccine.

All vaccines exhibit both specific and non-specific effects. The specific effects are measured by the efficacy against the target pathogen, while the non-specific effects can be detected by the change in all-cause mortality . All-cause mortality data (gender, age band, vaccination history, month of death) between January 2021 and May 2022 was compiled by the Office for National Statistics. COVID–19 vaccination gave good protection on many occasions but less so for younger ages. Each gender and age group shows its own unique vaccination benefit/disbenefit time profile. Individuals are free to make vaccination decisions. For example, women aged 18-39 show a cohort who do not progress beyond the first or second dose. The all-cause mortality outcomes for the Omicron variant showed a very poor response to vaccination with 70% of sex/age/vaccination stage/month combinations increasing all-cause mortality, probably due to unfavorable antigenic distance between the first-generation vaccines and this variant, and additional non-specific effects. The all-cause mortality outcomes of COVID–19 vaccination is far more nuanced than have been widely appreciated, and virus vector appear better than the mRNA vaccines in this specific respect. The latter are seemingly more likely to increase all-cause mortality especially in younger age groups. An extensive discussion/literature review is included to provide potential explanations for the observed unexpected vaccine effects.

In this paper, we study sums of finite products of Chebyshev polynomials of the first kind and Lucas polynomials and represent each of them in terms of Chebyshev polynomials of all kinds. Here the coefficients involve terminating hypergeometric functions ₂F₁ and these representations are obtained by explicit computations.

Considering the safety issues of Li ion batteries, all-solid-state polymer electrolyte has been one of the promising solutions. In this point, achieving a Li ion conductivity in the solid state electrolytes comparable to liquid electrolytes (>1 mS/cm) is particularly challenging. Employment of polyethylene oxide (PEO) solid electrolyte has not been not enough in this point due to high crystallinity. In this study, hybrid solid electrolyte (HSE) systems are designed with Li_1.3Al_0.3Ti_0.7(PO₄)₃(LATP), PEO and Lithium hexafluorophosphate (LiPF₆) or Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). Hybrid solid cathode (HSC) is also designed using LATP, PEO and lithium cobalt oxide (LiCoO₂, LCO)—lithium manganese oxide (LiMn₂O₄, LMO). The designed HSE system displays 3.0 × 10⁻⁴ S/cm (55 ℃) and 1.8 × 10⁻³ S/cm (23 ℃) with an electrochemical stability as of 6.0 V without any separation layer introduction. Li metal (anode)/HSE/HSC cell in this study displays initial charge capacity as of 123.4/102.7 mAh/g (55 ℃) and 73/57 mAh/g (25 °C). To these systems, Succinonitrile (SN) has been incorporated as a plasticizer for practical secondary Li ion battery system development to enhance ionic conductivity. The incorporated SN effectively increases the ionic conductivity without any leakage and short-circuits even under broken cell condition. The developed system also overcomes the typical disadvantages of internal resistance induced by Ti ion reduction. In this study, optimized ionic conductivity and low internal resistance inside the Li ion battery cell have been obtained, which suggests a new possibility in the secondary Li ion battery development.

This paper proposed emotion recognition methods for consecutive facial images, and implements the inference of neural network model on a field-programmable gate array (FPGA). The proposed emotion recognition methods are based on a neural network model architecture that combines convolution neural networks (CNNs), long short-term memory (LSTM), and fully connected neural networks (FCNNs), called CLDNN or ConvLSTM-FCN. This type of neural network mod-el can analyze the local feature sequences obtained through convolution of data, making it suita-ble for processing time-series data such as consecutive facial images. In this paper, sequences of facial images are sampled from videos corresponding to various emotional state of subjects. The sampled images are then pre-processed with the processes includes facial detection, greyscale conversion, resize, and data augmentation if necessary. The 2-D CNN in ConvLSTM-FCN is used for feature extraction for these pre-processed facial images. These sequences of facial im-age features are time sequences with dependent properties between the elements within them. The LSTM is then used to model these time sequences followed by fully connected neural net-works (FCNNs) for classification. The proposed consecutive facial emotion recognition method achieves an average recognition rate of 99.51% on RAVDESS dataset, 87.80% on BAUM-1s dataset and 96.82% on eNTERFACE’05 data set, using 10-fold cross-validation on the PC. Some com-parisons of recognition accuracies between the proposed method and the other existing related works are conducted in this paper. According to the comparisons, the proposed emotion recog-nition methods outperform the existing related researches. The proposed emotion recognition methods are then implemented on an FPGA chip using the neural network model inference algo-rithms in this paper, and the accuracies of the experiments conducted on the FPGA chip are iden-tical to those obtained on the PC. This verifies that the proposed neural network model imple-mented on the FPGA chip performs well.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

During a sanitary crisis, excess mortality measures the number of all-cause deaths, beyond what we would have expected if that crisis had not occurred. The high number of COVID-19 deaths started a debate in Italy with two opposite positions: those convinced that COVID-19 deaths were not, by default, excess deaths, because many COVID-19 deaths were not correctly registered, with the most part attributable to other causes and to the overall crisis conditions, and those who presented the opposite hypothesis. We analyzed the curve of the all-cause excess mortality, during the period January 5, 2020 – August 28, 2022, compared to the curve of the daily confirmed COVID-19 deaths, investigating the association between excess mortality and the recurrence of COVID-19 waves in Italy. We compared the two curves looking for the corresponding highest peaks and we found that 5 out of the 6 highest peaks (83.3%) of the excess mortality curve have occurred, on average, just a week before the concomitant COVID-19 waves hit their highest peaks of daily deaths (Mean 6.4 days; SD 2.4 days). This temporal correspondence between the moments when the excess mortality peaked and the highest peaks of the COVID-19 deaths provides further evidence that the all-cause excess mortality wave has been mostly driven by COVID-19 deaths

Vitamins are essential compounds obtained through diet that are necessary for normal devel-opment and function in an organism. One of the most important vitamins for human physiology is Vitamin A, a group of retinoid compounds and carotenoids which generally function as a mediator for cell growth, differentiation, immunity, and embryonic development, as well as serving as a key component in the phototransduction cycle in vertebrate retina. For humans, vitamin A is obtained through the diet, where provitamin A carotenoids like β-carotene, or preformed vitamin A such as retinyl esters are absorbed into the body via the small intestine and converted into all-trans retinol within the intestinal enterocytes. Specifically, once absorbed, carotenoids are cleaved by carote-noid cleavage oxygenases (CCOs), such as BCO1, to produce all-trans retinal that subsequently gets converted into all-trans retinol. CRBP2 bound retinol is then converted into retinyl esters (REs) by the enzyme lecithin retinol acyltransferase (LRAT) in the endoplasmic reticulum, which is then packaged into chylomicrons and sent into the bloodstream for storage in hepatic stellate cells in the liver or for functional use in peripheral tissues such as the retina. All-trans retinol also travels through the bloodstream bound to retinol binding protein 4 (RBP4), where it enters cells with the assistance of the transmembrane transporters, stimulated by retinoic acid 6 (STRA6) in peripheral tissues or retinol binding protein receptor 2 (RBPR2) in systemic tissues (e.g. in the retina and the liver respectively). Much is known about the intake, metabolism, storage, and function of vitamin A compounds, especially with regard to its impact on eye development and visual function in the retinoid cycle. However, there is much to learn about the role of vitamin A as a transcription factor in development and cell growth, as well as how peripheral cells signal hepatocytes to secrete all-trans retinol into the blood for peripheral cell use. This article aims to review literature re-garding the major known pathways of vitamin A intake from dietary sources into hepatocytes, vitamin A excretion by hepatocytes, as well as vitamin A usage within the retinoid cycle in the RPE and retina to provide insight on future directions of novel membrane transporters for vitamin A in retinal cell physiology and visual function.

Dietary vitamin A/all-trans retinol/ROL plays a critical role in human vision. ROL circulates bound to the plasma retinol-binding protein (RBP4) as RBP4-ROL. In the eye, the STRA6 membrane receptor binds to circulatory RBP4 and internalizes ROL. STRA6 is however not expressed in systemic tissues, where there is high-affinity RBP4 binding and ROL uptake. We tested the hypothesis, that the second retinol-binding protein 4 receptor 2 (Rbpr2) which is highly expressed in systemic tissues of zebrafish and mouse, contains a functional RBP4 binding domain, critical for ROL transport. As for STRA6, modeling and docking studies confirmed three conserved RBP4 binding residues in zebrafish Rbpr2. In cell culture studies, disruption of the RBP4 binding residues on Rbpr2 almost completely abolished uptake of exogenous vitamin A. CRISPR generated rbpr2-RBP4 domain zebrafish mutants showed microphthalmia, shorter photoreceptor outer segments, and decreased opsins, that were attributed to impaired ocular retinoid content. Injection of WT-Rbpr2 mRNA into rbpr2 mutant or all-trans retinoic acid treatments rescued the mutant eye phenotypes. In conclusion, zebrafish Rbpr2 contains a putative extracellular RBP4-ROL ligand-binding domain, critical for yolk vitamin A transport to the eye for ocular retinoid production and homeostasis, for photoreceptor cell survival.

Iterative Stochastic decoding is an alternative to standard fixed-point decoding of Low-density parity check codes (LDPC) to reduce inter-node routing. In this paper, we propose a Flexible Field-Programmable Gate Array (FPGA)-Based Stochastic decoding (SD) hardware architecture for LDPC codes in the Fifth-Generation (5G) New Radio (NR) Standard that supports decoding of set of various code rates. This decoder’s runtime flexibility is desirable to switch a better performing code rate automatically based on the channel conditions without the extra time needed for reprogramming of FPGA. An offline design method is implemented to generate the hardware description language (HDL) code description of the decoder for the required code-rate set, which is further synthesized and integrated into the Xilinx Kintex-7 series FPGA board to determine the hardware resource utilisation and processing throughput. The Synopsys design tools were employed during both the simulation and synthesis stages, in combination with TSMC 65-nm CMOS standard cell technology, to facilitate comparative analysis. Compared with state-of-the-art designs, the proposed architecture reduces hardware utilization by up to 26% and achieved energy efficiency by 52%.

DNA origami has emerged in recent years as a powerful technique for designing and building 2D and 3D nanostructures. While the breadth of structures that have been produced is impressive, one of the remaining challenges, especially for DNA origami structures intended to carry out useful biomedical tasks in vivo, is to endow them with the ability to detect and respond to molecules of interest. Target molecules may be disease indicators or cell surface receptors, and the responses may include conformational changes leading to release of therapeutically relevant cargo. Nucleic acid aptamers are ideally suited to this task and are beginning to be used in DNA origami designs. In this review we consider examples of uses of DNA aptamers in DNA origami structures and summarise what is currently understood regarding aptamer-origami integration. We review three major roles for aptamers in such applications: protein immobilisation, triggering of structural transformation, and cell targeting. Finally, we consider future perspectives for DNA aptamer integration with DNA origami.

Downward short-wave (SW) solar radiation is the only essential energy source powering the atmospheric dynamics, ocean dynamics, biochemical processes, etc. on our planet. Clouds are the main factor limiting the SW flux over the land and the Ocean. For the accurate meteorological measurements of the SW flux one needs expensive equipment - pyranometers. For some cases where one does not need golden-standard quality of measurements, we propose estimating incoming SW radiation flux using all-sky optical RGB imagery which is assumed to incapsulate the whole information about the SW flux. We used DASIO all-sky imagery dataset with corresponding SW downward radiation flux measurements registered by an accurate pyranometer. The dataset has been collected in various regions of the World Ocean during several marine campaigns from 2014 to 2022, and it will be updated. We demonstrate the capabilities of several machine learning models in this problem, which are multilinear regression, Random Forests, Gradient Boosting and convolutional neural networks (CNN). We also applied the inverse target frequency (ITF) re-weighting of the training subset and the approach of pre-classification in order to raise the SW flux approximation quality. We found that the CNN is capable of approximating downward SW solar radiation with higher accuracy compared to existing empiric parameterizations. We also found that the ITF reweighting of the training subset increases the approximation quality substantially. The estimates of the SW radiation flux using all-sky imagery may be of particular use in case of the need for the fast radiative budgets assessment of a site.

Dunaliella salina is a rich source of 9-cis β-carotene, which has been identified as important in the treatment of retinal dystrophies and other diseases. We previously showed that chlorophyll absorption of red light photons in D. salina is coupled to oxygen reduction and phytoene desaturation and increases the pool size of β-carotene [1]. Here we show for the first time that growth under red light also controls conversion of extant all-trans β-carotene to 9-cis β-carotene by β-carotene isomerases. Cells illuminated with red light from a light emitting diode (LED) during cultivation contained a higher 9-cis β-carotene content compared to cells illuminated with white or blue LED light. The 9-cis/all-trans β-carotene ratio in red light treated cultures reached >2.5:1 within 48 hours and was independent of light intensity. Illumination using red light filters that eliminated blue wavelength light also increased the 9-cis/all-trans β-carotene ratio. With norflurazon, a phytoene desaturase inhibitor which blocked downstream biosynthesis of β-carotene, extant all-trans β-carotene was converted to 9-cis β-carotene during growth with red light and the 9-cis/all-trans β-carotene ratio was ~2:1. With blue light under the same conditions, 9-cis β-carotene was likely destroyed at a greater rate than all-trans β-carotene (9-cis/all-trans ratio 0.5:1). Red light perception by the red light photoreceptor, phytochrome, may increase the pool size of anti-oxidant, specifically 9-cis β-carotene, both by upregulating phytoene synthase to increase the rate of biosynthesis of β-carotene and to reduce the rate of formation of reactive oxygen species (ROS), and by upregulating β-carotene isomerases to convert extant all-trans β-carotene to 9-cis β-carotene.

FoxP3 is a transcription factor essential for the differentiation and function of T regulatory cells (Tregs). There are two major subsets of Tregs: natural Tregs (nTregs) generated in thymus and inducible Tregs (iTregs) produced in peripheral immune system. It has been documented that iTreg development is dependent on soluble mediators including interleukin 2 (IL2), transforming growth factor β (TGFβ) and all-trans-retinoic acid (ATRA). In our experiments we performed a gene expression array, followed by Real-time PCR experiments, to study the expression of genes regulated by 1,25-dihydroxyvitamin D (1,25D) or ATRA in cells of myeloid origin. Our experiments revealed that ATRA alone, but also a cocktail of mediators consisting of IL2, TGFβ and ATRA, upregulate the expression of FOXP3 gene in lymphoid cells, but also in normal and leukemic myeloid cells. The FoxP3 expression is followed by a phenotypic changes in cells of myeloid origin. Our results indicate that signaling pathways which are used in the late stages of T cell differentiation, are also active in the cells of myeloid lineage

All vaccines exhibit specific and nonspecific effects. Specific effects are shown by the efficacy against the target pathogen, while nonspecific effects can be detected by the change in all-cause mortality. The real-world non-COVID-19 all-cause mortality (NCACM) data for the population of England between January 2021 and May 2023 was assessed. All vaccines administered were based on the original Wuhan antigen. Each gender and age group, along with COVID-19 variant shows its own unique NCACM vaccination benefit/disbenefit time profile. The efficacy of COVID-19 vaccination against COVID-19 disease/death per se is undisputed, however, the nonspecific outcomes of COVID–19 vaccination is far more nuanced than have been widely appreciated. This confirms an earlier study on the unanticipated nonspecific effects of influenza vaccination against all-cause winter mortality. Interestingly, a high proportion of NCACM beneficial effects occurred during the first 21 days following COVID-19 vaccination, while the worst example of increased NCACM occurred during the fourth dose of COVID-19 vaccination in 19–40-year-olds for the interval &gt;21 days post vaccination which led to NCACM 3- to 10-times higher than in the unvaccinated. By the time of the Omicron variant, NCACM outcomes in those aged 90+ are mostly adverse. The beneficial nonspecific effects of COVID-19 vaccination increase with age and reach their maximum effect during the second week post vaccination for age groups below 50 years, rising to during the third week for those aged 70+. Finally, we discuss the mechanisms by which COVID-19 vaccination could induce wider nonspecific effects. Most of these mechanisms seem to depend on gene regulation by noncoding RNAs which also interact with mRNAs. We suggest that further international studies are required to discern the nonspecific NCACM effects of the different COVID-19 variants other than the three variants prevalent in the UK, and different types/manufacturer of COVID-19 vaccines which have been employed around the world. We can only speculate regarding the nonspecific effects of the COVID-19 vaccines administered to persons with an asymptomatic infection, and during vaccine waning. Vaccines not only need to be effective against the target pathogen, as primarily determined by antibody production, but need to minimize any unanticipated adverse nonspecific effects against all-cause mortality.

Humankind has entered a new era wherein a main characteristic is the convergence of various technologies providing services exerting major impact upon all aspects of human activity, be it social interactions as well as interactions with the natural environment. Fixed networks are about to play a major role in this convergence, since they form, along with mobile networks, the backbone that provides access to a broad gamut of services, accessible from any point of the globe. It is for this reason that we introduce a forward-looking approach for fixed networks, particularly focused on Fixed 6th Generation (F6G) networks. First, we adopt a novel classification scheme for the main F6G services, comprising six categories. This classification is based on the key service requirements, namely latency, capacity and connectivity. F6G networks differ from those of previous generations (F1G-F5G) in that they concurrently support multiple key requirements. We then propose concrete steps towards transforming the main elements of fixed networks, such as optical transceivers, optical switches etc. such that they satisfy the new F6G service requirements. Our study categorizes the main networking paradigm of optical switching into two categories namely ultra-fast and ultra-high capacity switching, tailored to different service categories. With regard to the transceiver physical layer, we propose: a) use of all-optical processing to mitigate performance barriers of analog to digital and digital to analog converters (ADC/DAC); b) exploitation of optical multi-band transmission, space division-multiplexing and adoption of more efficient modulation formats.

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

This work implements a stable algorithm in Field-Programmable Gate Arrays (FPGAs) for which two architectures (unrolling the loop) were developed and analyzed. The algorithm recovers sources located at the boundary separating two homogeneous media that make up a two-dimensional non-homogeneous region from measurements on the boundary of such region. The problem of recovering these sources is an ill-posed inverse problem as small errors in the measurement can produce important changes in the source location. Inverse source problems have many applications in different areas, such as engineering and medicine, making the proposed implementation important. The first architecture (mode one) allows considering different operating speeds, which is an advantage depending on whether we work with fast or slow signals. The second one (mode two) reduces resource consumption by exploiting the characteristics of the source identification algorithm, which is an advantage for multichannel problems such as inverse electrocardiography or electroencephalography. The architectures were tested on four FPGAs of the 7 Series of Xilinx: Spartan-7 xc7s100fgga484, Virtex-7 xc7v585tffg1157, Kintex-7 xc7k70tfbg484, and Artix-7 xc7a35tcpg236. The two FPGA implementations of the algorithm were validated using synthetic examples implemented in MATLAB. The results presented here can be extended to concentric spheres and complex geometries.

Recently, there has been, on the one hand, an increase in the complexity of digital device designs and, on the other hand, an increase in the requirements for the development time and the reliability of the designs. One of the directions of solving this problem is developing new techniques for designing digital devices.This paper proposes a new technique for designing digital devices based on finite state machines with datapath (FSMD), when the functioning of the device is described in the form of an algorithm state machine with datapath (ASMD) charts. The new technique is called ASMD-FSMD. Different digital device design techniques are compared to each other using design examples of a synchronous multiplier on field programmable gate array (FPGA). The efficiency of the ASMD-FSMD technique compared to the traditional approach in terms of area and performance was investigated. The ASMD-FSMD technique, compared to the traditional one, reduces the area from 28.6% to 39.7% and increases the speed for some designs to 17.6%. In addition, using the ASMD-FSMD technique significantly reduces design time and increases design reliability. In conclusion, recommendations for using the ASMD-FSMD technique are made.