The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

In this study, carbon-quantum-dot (CQD)-decorated TiO2 was prepared using an ultrasonic doping method and applied in the photocatalytic degradation of naphthalene under sunlight irradiation. The CQDs were synthesized from a typical macroalgae via diluted sulfuric acid pretreatment and hydrothermal synthesis using an optimal design, i.e., 3 wt% and 200 oC, respectively. The CQD/TiO2 composite remarkably enhanced the photocatalytic activity. The degradation of naphthalene under a visible light environment indicated that there is a synergistic mechanism between CQDs and TiO2, in which the generation of reactive oxygen species is significantly triggered; in addition, the N that originated from the macroalgae accelerated the photocatalytic efficiency. Kinetic analysis showed that the photo-catalytic behavior of the CQD/TiO2 composite followed a pseudo-first-order equation. Consequently, our combined experimental approach not only provides a facile pretreatment process for bio-CQDs synthesis, but also delivers a suitable TiO2 photocatalyst for up-conversion, along with critical insights into the development of harmful macroalgae resources.

Polyphenols are the most common organic compounds in wine. They improve both the sensory aspects of wine and human health by activating antioxidant systems. Therefore, there is a great need for a simple, fast and accessible method to determine the polyphenol content of wine. The aim of this study is to characterize polyphenolic compounds in natural wine samples using an electrochemical method and a modified carbon paste electrode with TiO2 nanoparticles. This work is motivated by the promising improvement of the sensing properties of a TiO2 nanoparticle-modified carbon paste electrode observed in the electrooxidation of different polyphenols. Since the voltammetric response of wine is largely irreversible, another motivation was the possibility of improving the processing of voltammograms to obtain data indicative of wine polyphenols, based on the approach described in the seminal work by Espinoza et al. The modified electrode studied provides an improved and reproducible voltammetric response of gallic acid in wine samples and provides a good basis for further development of an integrated sensor/data system with the possibility of wider application for the quantification of gallic acid as a flavor and visually relevant parameter in winemaking.

The highly crystalline ZnAl Layered Double Hydroxides (ZnAl-NO3- LDHs) are utilized for the potential transformation into Mixed Metal oxides (MMO) through thermal decomposition and used further for the photodegradation of phenol to assess the influence of calcination on ZnAl LDHs with enhanced photoactivity. The structure, composition, and morphological evolution of ZnAl-LDHs to ZnO-based MMO nanocomposites, which are composed of ZnO and ZnAl2O4, after calcination at different temperatures (400-600 ºC), are all thoroughly examined in this work. The final ZnO and ZnAl2O4 base nanocomposites showed enhanced photocatalytic activity. The findings demonstrated that calcining ZnAl-LDHs from 400 to 600 °C increased the specific surface area and also enhanced the interlayer spacing of d003 while the transformation of LDHs into ZnO/ZnAl2O4 nanocomposite through calcining the ZnAl-LDH precursor at 600 °C showed significant photocatalytic properties, leading to complete mineralization of phenol under UV irradiation.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

Many quantum dot light-emitting diodes (QLEDs) utilize ZnO nanoparticles (NPs) as an electron injection layer (EIL). However, the use of ZnO NP ETL material often results in charge imbalance within the quantum dot (QD) emitting layer (EML) and exciton quenching at the interface of QD EML and ZnO NP EIL. To overcome these challenges, we introduced an Arginine (Arg) interlayer (IL) onto the ZnO NP EIL. The Arg IL elevated the work function of ZnO NPs, thereby suppressing electron injection into the QD, leading to improved charge balance within the QDs, Additionally, the inherent insulating nature of the Arg IL prevented direct contact between QDs and ZnO NPs, reducing exciton quenching and consequently improving device efficiency. The inverted QLED (IQLED) utilizing a 20-nm-thick Arg IL on ZnO NP EIL exhibited a 2.22-fold increase in current efficiency and a 2.28-fold increase in EQE and compared to an IQLED without an IL. Likewise, the IQLED with a 20-nm-thick Arg IL on ZnO NP EIL demonstrated a 1.34-fold improvement in current efficiency and a 1.36-fold increase in EQE compared to IQLED with a 5-nm-thick PEI IL on ZnO NPs.

In this work, we report the engineering of a sub-70 nm nanocomposite of ZnO/Zn2TiO4 using a low-temperature solution-phase method. Titanium isopropoxide and zinc acetate were used as precursors, and isopropyl alcohol and water were used as solvents. The investigation focused on the growth of nanocomposites by varying the concentrations of precursors and surfactants, as well as their efficiency within different pH ranges. All three ZnO/Zn2TiO4 nanocomposites consist of hexagonal wurtzite ZnO and Zn2TiO4 structures in the three nanocomposites. The crystallite size in three ZnO/Zn2TiO4 nanocomposites, with a hexagonal wurtzite ZnO structure, were measured to be 62.67, 40.34, and 39.50 nm. The crystallite size values in three ZnO/Zn2TiO4 nanocomposites were 26.15 nm, 25.36 nm, and 21.24 nm, respectively, with Zn2TiO4. Morphological observations, conducted using FESEM, reveal the formation of three ZnO/Zn2TiO4 nanocomposites across the entire sample. These nanocomposites resemble dispersed cotton packets, with sizes ranging from 18 to 350 nm. Peaks in the range of 610-1250cm-1 are attributed to Ti-O bond formation and peak located at 1350-1450 cm-1 are attributed to Zn-O bond formation. Also, EDX spectrum reveals peaks for various sample components such as Ti, O and Zn. UV spectrums confirmed the formation of three nanocomposite of ZnO/Zn2TiO4 as showing two peaks for each sample. Photocatalytic investigation carried out by analyzing the UV-Visible absorption spectra of methylene blue dye on the surface of ZnO/Zn2TiO4 nanocomposites, dye degradation at various irradiation time intervals, dye degradation at varied catalyst concentrations and the influence of pH on dye-degradation. Furthermore, the said nanocomposites were used to degrade environmental pollutant (Methylene blue dye). Different sets of experiments were conducted under ambient conditions which show an excellent photo catalytic degradation efficiency.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

In the context of high-temperature water vapor treatment, Zn-Mg-Al alloy-coated steel sheets exhibit the emergence of a black surface. This study aims to explore the factors and mechanisms contributing to surface blackening by inducing black surfaces on Zn-Mg-Al alloy-coated steel sheets, which were fabricated through molten coating subjected to water vapor treatment at 150 degrees Celsius. The surfaced composition was predominantly identified as ZnO, a zinc oxide film, validated through X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Morphological analysis of the surface and cross-section post-water vapor treatment revealed a disrupted lamellar structure with diffused features, resulting in the formation of an oxide film. Optical properties analysis demonstrated an increased absorbance and a decreased bandgap energy after water vapor treatment, indicative of an augmented blackening effect. Consequently, the high-temperature water vapor treatment led to the formation of oxides on the surface, with the highly reactive Mg and Al extracting oxygen from the predominantly present ZnO surface. This process resulted in the creation of an oxygen-deficient oxide, ultimately causing surface blackening.

In this study, we investigated the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material by coating it with ZnO and examined the changes in surface composition using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, we investigated the electrochemical properties, including discharge capacity and initial irreversible capacity, of the modified materials. The results revealed that ZnO predominantly existed on the material surface, exerting influence on both surface composition and electrochemical characteristics. As the ZnO coating amount increased, the nickel and manganese content on the material surface also increased, and heat treatment at 400 °C resulted in the formation of composite oxides of transition metals and zinc on the material surface. The bonding energy of transition metals increased, and ZnO coating at a mass fraction of 2 % effectively suppressed irreversible reactions around 3.6 V at 55 °C, thereby improving initial coulombic efficiency. Battery materials coated with 2% ZnO exhibited optimal discharge capacity and cycle life at 55 °C/0.5 C.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

A series of ZnO doped nitrogen-carbon materials (xZnO-N-C) with ZnO content of 5-40% are prepared by vacuum curing-carbonization strategy using polyamide-imide as N-C source and zinc nitrate as metal source for propane dehydrogenation (PDH). 20ZnO-N-C exhibits outstanding initial activity (propane conversion of 35.2% and propene yield of 24.6%) and relatively low deactivation rate (0.071 h-1) at 600 ◦C. The detailed characterization results show that small ZnO nanoparticles (5.5 nm) with high dispersion on the catalyst could be obtained by adjusting ZnO loading. Moreover, much more nitrogen-based species especially ZnNx species are formed on 20ZnO-N-C by comparison with 20ZnO-N-C-air prepared by curing-carbonization without vacuum, which may contribute for the higher product selectivity and catalytic stability of 20ZnO-N-C. The probable active sites for PDH reaction on the catalyst system are proposed to be C=O species and Zn2+ species. Moreover, the aggregation of ZnO nanoparticles is the primary reason for the activity loss on this catalyst system. The present finding not only provides the feasible construction strategy for the metal oxide doped nitrogen-carbon materials but also valuable guidance for the design of efficient catalyst in dehydrogenation of light alkane.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

The novel ternary composites, BiOBr-TiO2-attapulgite (BTA), were synthesized using a simple hydrothermal and water-bath method, exhibiting excellent photocatalytic performance to mul-tiple xanthates. For BTA photocatalyst, TiO2 and BiOBr were uniformly loaded on the surface of acid-activated attapulgite. As a widely used collector in mining processes, sodium ethyl-xanthate (SEX) was selected as the target pollutant due to its high toxicity. The BTA ternary photocatalyst demonstrated significantly higher adsorption and photocatalytic degradation performance compared to TiO2 nanoparticles, BiOBr nanosheets, and BiOBr-TiO2 heterojunction. Structural characterization and experimental results indicated that the exceptional photocatalytic degrada-tion efficiency of BTA was mainly attributed to the formation of heterojunction between BiOBr and TiO2, as well as the presence of additional active adsorption sites provided by attapulgite. Free radical scavenging experiments and EPR results confirmed that the photogenerated holes were the predominant active species to photodegrade SEX throughout the entire experiment. The LC-MS results provided insight into potential degradation pathways of SEX. This research demonstrates that BTA, as a novel triple composite material, achieves rapid and complete degradation to 20 mg/L SEX within 20 min. This work presents a novel approach to synthesize mineral-based photo-catalysts, which have broad prospects for application in flotation wastewater treatment.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99±0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile strength in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile strength to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

In this study, the effect of ZnO nanoparticles (Zn NPs) on the performance of epoxy resin composites was investigated. The new ZnO/epoxy resin composites were synthesized using halloysite nanotubes (HNT) and different types of ZnO nanoparticles (commercial ZnO and ZnO-ODTES). These ZnO nanoparticles were utilized for intending to enhance the interfacial bonding between the epoxy resin and the reinforcement. Various methods such as FTIR, TGA, DSC, TEM-EDX, and Nanoindentation analyses were used to prove that the ZnO nanoparticles can improve the properties of epoxy resin composites. The thermal properties of the epoxy resin composites were enhanced to a greater extent by the addition of ZnO NPS. DSC testing proved that the epoxy resin composites modified with ZnO NPS are more flexible and elastic than unmodified epoxy resin. It was seen that the epoxy resin modified with ZnO-ODTES shows a much improved hardness and penetration depth compared to the other samples. These findings can pave the way for the developing of ZnO-based marine coatings with improved properties.

The use of nanoparticles as antimicrobial agents can be one of the strategies to overcome the tendency of microbes to become resistant to antibiotics’ action. In this study, two composites ZnO/Au and ZnO/Ag, having 1% wt. of noble metal content, were synthesized by simple aqueous solution methods. The structure and morphology of the resulting nanocomposites were analyzed by standard structural and optical characterization methods. The formation of Au NPs and Ag NPs in these experiments was also discussed. The antimicrobial properties of ZnO, ZnO/Au and ZnO/Ag nanomaterials were investigated against Gram-negative bacteria (Pseudomonas aeruginosa) and Gram-positive bacteria (Staphylococcus aureus). The electrostatic interaction between ZnO and noble metals nanoparticles have contributed to a better visible light adsorption, which led to an enhanced antimicrobial activity. The photocatalytic tests indicated an improvement in photocatalytic degradation of the methylene blue (MB) under UV irradiation using ZnO/Au and ZnO/Ag nanocomposites compared to bare ZnO. The introduction of noble metallic nanoparticles in ZnO matrix proved to be an effective strategy to increase their antimicrobial activity against P. aeruginosa and S. aureus and their photocatalytic activity evaluated through the degradation of MB dye. Comparing the enhancing effects of Au and Ag, it was found that ZnO/Au was a better antimicrobial agent while ZnO/Ag was more effective photocatalyst under UV irradiation.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

The demand for high-energy-density batteries necessitates novel anode materials. Transition metal oxides (TMOs) show promise due to their high capacity, sustainability, and cost-effectiveness. However, TMO-based anodes face challenges related to expansion and conductivity. This study presents a two-step dilution crystallization method to fabricate porous ZnO nanoflowers at a moderate temperature. In-situ integration with carbon nanotube dispersants enhances conductivity and reduces agglomeration. The resulting composite anode exhibits impressive initial discharge capacity (2314.2 mAh g-1) and cycling stability (580.5 mAh g-1 over 50 cycles). This study provides a facile approach for next-generation anode materials.

The electronic, optical, and magnetic properties of Nd-doped ZnO systems were calculated using the DFT/GGA+U method. According to the results, the Nd dopant causes lattice parameter expansion, negative formation energy, and bandgap narrowing, resulting in the formation of an n-type degenerate semiconductor. Overlapping of the generated impurity and Fermi levels results in a significant trap effect that prevents electron-hole recombination. The absorption spectrum demonstrates a redshift in the visible region and improved intensity, leading to enhanced photocatalytic performance. The Nd-doped ZnO system displays ferromagnetic, with FM coupling due to strong spd-f hybridization through magnetic exchange interaction between the Nd-4f state and O-2p, Zn-4s, and Zn-3p states. These findings imply that Nd-doped ZnO may be a promising material for DMS spintronic devices.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

Heat transfer fluids are used in various industrial systems to maintain them in perfect operating conditions. Extensive research efforts have been dedicated to enhance the thermal properties of these heat transfer fluids to improve their efficiency. Developing nanofluids is a potential candidate for such enhancements. This study investigates the impact of incorporating TiO2 nanoparticles into two types of oils: transformer oil (NYTRO LIBRA) and virgin coconut oil (manufactured by Govi Aruna Pvt. Ltd.) at different temperatures and with varying volume fractions. The nanofluids were prepared using a two-step method by adding CTAB (Cetyltrimethylammonium bromide) surfactant. To minimize nanoparticle agglomeration, this study employed relatively low-volume fractions. Thermal properties by means of thermal conductivity, thermal diffusivity, and volumetric heat capacity were measured in accordance with ASTM (American Society for Testing and Materials) standard methods, using a multifunctional thermal conductivity meter (LAMBDA thermal conductivity meter). The measured thermal conductivity values were compared with theoretical models and previous research findings. It was confirmed that the modification of thermal properties was enhanced by doping TiO2 nanoparticles with different volume fraction.

The development of photocatalysts with a wide spectral response and effective carrier separation capability is essential for the green degradation of tetracycline. In this work, a magnetic recyclable Z-scheme ZnO/ZnFe2O4 heterojunction (ZZF) was successfully constructed by the solid phase method using MIL-88A(Fe)@Zn as the precursor. Appropriate band gap width and Z-scheme charge transfer mechanism make ZZF have excellent visible light absorption performance, efficient charge separation and strong redox ability. Under visible light irradiation, the degradation efficiency of TCH for optimal sample ZZF2 can reach 86.3 % within 75 min in deionized water, and achieve 92.9 % within 60 min in tap water, which exhibits superior stability and reusability after five cycles. Moreover, the catalyst in the water can be conveniently recovered by magnetic force. After visible light irradiation for 70 minutes, the temperature of the reaction system increased by 21.9 °C. Its degradation constant (35.53×10-3 min-1) increases 5.1 times that at room temperature (6.95×10-3 min-1). Thermal energy perfects the kinetic driving force of the reactants and promotes carrier migration to produce more •O2- and •OH. This work provides a potential candidate and inspires the design of photocatalyst for tetracycline hydrochloride degradation.

Although Sn has been intensively studied as one of the most promising anode materials to replace commercialized graphite, its cycling performance and rate performance are still unsatisfactory owing to insufficient control of its large volume change during cycling and poor electrochemical kinetics. Herein, we propose a Sn-TiO2-C ternary composite as a promising anode material to overcome these limitations. The hybrid TiO2-C matrix synthesized via two-step high-energy ball milling effectively regulated the irreversible lithiation/delithiation of the active Sn electrode and facilitated Li-ion diffusion. At the appropriate C concentration, Sn-TiO2-C exhibited significantly enhanced cycling performance and rate capability compared to its counterparts (Sn-TiO2 and Sn-C). Sn-TiO2-C delivers good reversible specific capacities (669 mAh g-1 after 100 cycles at 200 mA g-1 and 651 mAh g-1 after 500 cycles at 500 mA g-1) and rate performance (446 mAh g-1 at 3000 mA g-1). The superiority of Sn-TiO2-C over Sn-TiO2 and Sn-C was corroborated by electrochemical impedance spectroscopy, which revealed faster Li-ion diffusion kinetics in the presence of the hybrid TiO2-C matrix than in the presence of TiO2 or C alone. Therefore, Sn-TiO2-C is a potential anode for next-generation Li-ion batteries.

CuO/ZnO/Al2O3 catalyst is a commonly used catalyst for rea methanol steam reforming reaction. Oxalic acid was as precipitant in preparing oxalate precursor of CuO/ZnO/Al2O3 catalyst by co-precipitation, deionized water and ethanol were as solvents, microwave irradiation and water bath were as aging heating manner respectively. It indicated that ethanol selected crystal phase composition of oxalate precursors and restricted their growth. Microwave irradiation prompted the isomorphous substitution between Cu2+ of CuC2O4 and Zn2+ of ZnC2O4 in mother liquid, forming the master phase (Cu,Zn)C2O4 in precursor, the solid solution Cu-O-Zn formed after calcination, which exhibited nano-fibriform morphology. It possessed small CuO grains, large surface area and strong synergy between CuO and ZnO, which is beneficial to improve the catalytic performance of methanol steam reforming, the STY of H2 reached 516.7 mL·g-1·h-1, and the selectivity of CO was only 0.29%.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

Building heterojunction is promising strategy for the achievement of highly efficient photocatalysis. In this study, a novel SnIn4S8@ZnO Z-scheme heterojunction with tight contact interface was successfully constructed through a facile two-step hydrothermal method. The phase composition, morphology, and photophysical properties of SnIn4S8@ZnO were studied through a series of characterization methods, respectively. Methylene blue (MB) was selected as the target pollutant for photocatalytic degradation and the degradation process was fitted with pseudo-first order kinetics. The as-prepared SnIn4S8@ZnO heterojunctions exhibited outstanding photocatalytic activities for the degradation of MB. The optimized sample (ZS800), in which the molar ratio of ZnO to SnIn4S8 was 800, displayed the highest photodegradation efficiency of MB (91%) within 20 min. Furthermore, the apparent rate constant of photodegradation for MB of ZS800 (0.121 min−1) was 2.2 times higher than that of pure ZnO (0.054 min−1). The improvement of photocatalytic activity could be attributed to the effective spatial separation of photogenerated charge carriers through a Z-scheme heterojunction with intimate contact interface. This work will provide a new insight into constructing excellent ZnO-based photocatalytic systems for wastewater purification.

Green products have excellent potential for discovering and producing new medicinal products. In recent years, there is a growing interest towards the green synthesis of metal nanoparticles, particularly from plants sources. This eco-friendly approach was used in the recent research to biosynthesize zinc oxide nanoparticles (ZnO NPs) from Cissus antractica plant. The present study aims to examine the cell cytotoxicity, cell death, and pathways of apoptosis in lung cancer cells (A549) and inflammation properties treated with biosynthesized ZnO NPs. Additionally, synthe-sized ZnO nanoparticles were characterized using UV–vis spectroscopy, X-ray diffraction (XRD), Transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FT-IR), and Energy-dispersive X-ray spectroscopy (EDS). The XRD and TEM analyses exhibited 31 nm as the size of synthesized nanoparticles, the pure crystal form of ZnO NPs, and the shape of the NPs as nearly spherical and hexagonal quartzite. The MTT assay used for cytotoxicity evaluation de-picted the significant toxic effect of CA-ZnONPs against the A549 lung cancer cells at concentra-tions up to 20 µg/mL than non-cancerous cells. Furthermore, we observed an elevated ROS level in cancer cells. These NPs also demonstrated dose-dependent ability to suppress colony for-mation and cell migration, which increases their potential as a lung cancer treatment. Further-more, The NPs formulation's ability to induce apoptosis in cancer cells was further supported by Hoechst and propidium iodide dye. Further, CA ZnO NPs increased the gene expression of BAX, Cyto-c, Caspase 3 and 9, but decreased the expression of Bcl-2, indicating that the nanoformulation triggered mitochondrial-mediated apoptosis. Besides, this study showed that NPs suppressed in-flammatory responses by subsequently decreasing reactive oxygen species (ROS) generation, downregulating the expression of the pro-inflammatory cytokines TNF-α, iNOS, COX-2, IL-6, IL-8, and NO. Moreover, the study's findings imply that Cissus antractica are a potential source with biosynthesize nanoparticles that can might be further investigated for the progress of an-ti-inflammatory and anti-cancer drugs with further study.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

This study presents a straightforward electrochemical and plasma deposition method for producing Cobalt-doped Blue-TiO2 nanotubes with enhanced catalytic properties. After a titanium plate has been anodized, specific procedures are carried out that cause oxygen vacancies to form inside the TiO2 nanostructures. The obtained catalysts were subjected to electrochemical tests (to identify charge transfer resistance and flat band potential), optical analysis (to determine the band gap and Urbach energy) and also characterized in terms of morphology, wettability and antibacterial effect in order to understand and analyze the impact of the Co doping method on the final catalyst characteristics. A hydrophilic film with star-shaped structures and with antibacterial effect was created when cobalt was electrochemically doped to Blue-TiO2 nanotubes. By using this electrochemical doping technique, the Urbach energy was raised from 1.171 to 3.836 eV while the band gap energy was decreased from 3.04 to 2.88 eV. Additionally, photodegradation experiments using artificial doxycycline (DOX) water were conducted to determine the practical relevance of the research findings. In areas like antimicrobial applications and photodegradation of DOX, these extra experiments aimed to show the practical applicability and potential advantages of the research findings.

Artemisia absinthium (A. absinthium) leaf extract was successfully used to create zinc oxide nanoparticles (ZnO NPs), and their properties were investigated via several techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), Fourier transform infrared (FTIR), and UV–Vis spectroscopy. SEM analysis confirmed the spherical and elliptical shapes of the particles. Three different zinc peaks were observed via EDX at energies of 1, 8.7, and 9.8 keV, together with a single oxygen peak at 0.5 keV. XRD analysis identified ZnO NPs as having a hexagonal wurtzite structure with a particle size that decreased from 24.39 to 18.77 nm, and with an increasing surface area (BET) from 4.003 to 6.032 m2/g for the ZnO (without extract) and green ZnO NPs, respectively. FTIR analysis confirmed the groups of molecules that were accountable for stabilizing and minimizing the ZnO NPs, which was apparent at 3400 cm. Using UV–Vis spectroscopy, the band gap energies (Egs) for the green ZnO and ZnO (without extract) NPs were estimated, and the values were 2.65 and 2.79 eV, respectively.

The aim of this study was to develop sago starch-based bionanocomposite films containing TiO2 nanoparticles and Penganum harmala extract (PE) to increase the shelf life of chicken fillets. First, sago starch films containing different levels of TiO2 nanoparticles (1, 3 and 5%) and PE (5, 10 and 15%) were prepared, and the thickness, barrier properties, and antibacterial activity of the films. Then, the produced films were used for the chicken fillets packaging and the physicochemical and antimicrobial properties of samples were examined during 12-day storage at 4°C. The results showed that the addition of the combination of nanoparticles and extract and increasing their levels in the films increased the antibacterial activity against gram-positive and gram-negative bacteria. The results also demonstrated that during the storage period, the pH, total volatile basic nitrogen (TVB-N), and the number of aerobic mesophilic bacteria, psychrophilic bacteria, coliforms, molds and yeasts in fillets increased (p&lt;0.05). However, coating the fillets with bionanocomposites can significantly reduce the rate of change in chemical properties and microbial growth of the samples. This sample increased the shelf life of the fillets by at least 8 days compared to the control sample.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

In today's society, mankind is confronted with two major problems: the energy crisis and the greenhouse effect. The artificial photosynthesis can use solar energy to convert greenhouse gas CO2 into high-value compounds, which is an ideal solution to alleviate the energy crisis and solve the problem of global warming. The combination of ZnO and polythiophenes (PTh) can make up for each other's drawbacks, thus improving the photoresponse behavior and separation efficiency of photogenerated carriers. PTh layer can transfer photogenerated electrons to ZnO, thereby extending the lifetime of photogenerated charges. The production rate of CH4 from photoreduction of CO2 with ZnO/PTh10 is 4.3 times that of pure ZnO, and the selectivity of CH4 is increased from 70.2% to 92.2%. The conductive PTh can absorb photons to induce π–π* transition, the photogenerated electrons can transfer from LUMO to the conduction band (CB) of ZnO, thus more electrons involve in the reduction of CO2.

Some of Iran's gas resources are known as sour gas because one of the major by-products of this gas is water. In fact, natural gas is combined with water vapor in underground reservoirs. In some areas, the amount of water vapor in natural gas is so high that it can be used as a source of drinking water. However, it should be noted that water vapor in natural gas may exacerbate corrosion in pipes and industrial equipment, and the combustion of more natural gas produces high temperatures that can lead to the production of nitrogen oxides (NOx), which They are the cause of air pollution. This is while the processed gas has a standard percentage composition in which the amount of water has the lowest position. The removal of moisture from natural gas is due to the need to prevent the reduction of the calorific value of the gas and also to purify the gas in order to achieve the necessary standards for delivering gas to petrochemicals, industries and domestic uses. The main goal of this research is to investigate the influencing parameters on zeolite TiO2 nanocomposite membranes in order to absorb moisture from gas. For this reason, with the construction of a TiZ-V membrane as a standard membrane, the result of the initial evaluation of a suitable membrane for gas dehumidification was made, and this membrane was placed as a standard for measuring the effect of the manufacturing parameters in a way that in each stage of membrane construction It was found that it was different from standard TiZ-V membrane only in terms of one parameter. This type of investigation made it possible to determine the effect of various effective parameters in membrane construction on efficiency. The findings showed that increasing the concentration of SiO2 has the greatest effect on increasing the water flux of the membrane. According to the other findings of this study, the effect of increasing the reaction time of the vapor phase carrier has been to reduce the process of paternity selectivity loss at higher pressures. Although due to the safety limitation of the equipment to measure the efficiency of the membrane at pressures higher than 7 bar, this measurement was not carried out, but charts were presented regarding the state of the water in the water, which were a measure of the superiority of the water in the water in comparison to the gas in the water, which is the higher water in the water It is an indicator of the appropriateness of the membrane's efficiency at its corresponding pressure, so that the examination of the difference between these two graphs shows the possibility of using the membrane at higher pressures

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

Photocatalytic technology based on specific band structure of semiconductors offers a promising way to solve the urgent energy and environmental issues in modern society. In particular, hydrogen production from water splitting over semiconductor photocatalysts attracts great attention owing to the clean source and application of energy, which highly depends on the performance of photocatalysts. Among the various photocatalysts, TiO2 has been intensively investigated and used extensively due to its outstanding photocatalytic activity, high chemical stability, non-toxicity and low cost. However, pure TiO2 has a wide band gap of approximately 3.2 eV, which limits its photocatalytic activity for water splitting to generate hydrogen only under ultraviolet light, excluding most of the inexhaustible sunlight for human beings. Fortunately, the band gap of semiconductors can be manipulated, in which introducing oxygen defects is one of the most effective measures to narrow the band gap of titanium oxides. This review starts out by the fundamentals of photocatalytic water splitting for hydrogen production over TiO2, discusses the latest progress in this field, and summarizes the various methods and strategies to induce oxygen defects in TiO2 crystals. Then, the next section outlines the modification approaches of oxygen-deficient titanium oxide (TiO2-δ) to further improve its photocatalytic performance. Finally, a brief summary and outlook of the researches on TiO2-δ photocatalysts for water splitting to produce hydrogen were presented.

This study describes a comparative in vitro study of the toxicity behavior of zinc oxide (ZnO) nanoparticles and micro-sized particles. The study aimed to understand the impact of particle size on ZnO toxicity by characterizing the particles in different media, including cell culture media, human plasma, and protein solutions (bovine serum albumin and fibrinogen). The study used various techniques such as atomic force microscopy (AFM), transmission electron microscopy (TEM), and dynamic light scattering (DLS) to characterize the particles and their interactions with proteins. Hemolytic activity, coagulation time, and cell viability assays were used to assess ZnO toxicity. The results highlight the complex interactions between ZnO NPs and biological systems, including their aggregation behavior, hemolytic activity, protein corona formation, coagulation effects, and cytotoxicity. Moreover, the study indicates that ZnO nanoparticles are not more toxic than micro-sized particles, and the 50 nm particles resulted in general the least toxic. Furthermore, the study found that at low concentrations, no acute toxicity was observed. Overall, this study provides important insights into the toxicity behavior of ZnO particles and highlights that no direct relationship between nanometer size and toxicity can be directly attributed.

This work presents an LC resonant passive wireless gas sensor with a novel structure designed to mitigate the negative impact of substrate. The LC sensor antenna with the new structure and the reader antenna were designed and optimized utilizing HFSS software to improve the transfer efficiency. The superiority of the designed structure compared with the general ones is highlighted and verified. The change in the substrate capacitance has essentially no interference with the parameters to be measured of the LC sensor. The sensor with the new structure was prepared by combining etching and sputtering methods. The structure of the ZnO nanowires (NWs) was characterized to confirm their high purity and wurtzite crystal structure. The LC gas sensors demonstrated excellent wireless sensing performance including a low detection limit of 0.5 ppm NO2, high response of 1.058 and outstanding stability at 180 °C. The developed new sensor structure not only prevented interference from the substrate during gas sensing testing, but also expanded the choice of sensor substrates, playing a critical role in the development of sensors based on LC resonance principle.

The work reports a facile synthesis of high thermally-stable nanocrystalline anatase TiO2 nanoparticles (NPs) doped with different atomic concentrations (0.5, 1.0, 3.0, and 6.0%) of Gd3+ and Nd3+ ions by a template-free and one-step solvothermal process, using titanium(IV) butoxide as titanium precursor and dimethyl sulfoxide (DMSO) as solvent. The structure and morphology of the Gd3+, Nd3+, and 0.5%Gd3+-0.5%Nd3+/doped TiO2 NPs have been characterized by using various analytical techniques. The Gd3+/ and Nd3+/TiO2 molar ratios were found to have a pronounced impact on the crystalline structure, size, and morphology of TiO2 NPs. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) studies revealed the proper substitution of Ti4+ by Gd3+ and Nd3+ ions in the TiO2 host lattice. The as-prepared Gdx/TiO2, Ndx/TiO2, and Gd1.0/Ndx/TiO2 bimetallic NPs, x = 0.5, 1.0, 3.0, and 6%, have been investigated as electrocatalysts for hydrogen evolution reaction (HER) in 1.0 M KOH solution using a variety of electrochemical techniques. At any doping percentage, the Gd1.0/Ndx/TiO2 bimetallic NPs showed higher HER catalytic performance than their corresponding counterparts i.e. Gdx/TiO2 and Ndx/TiO2. Upon increasing the Nd content from 0.5 to 6.0%, the HER catalytic performance of the Gd1.0/Ndx/TiO2 bimetallic NPs was generally enhanced. Among the studied materials, the bimetallic Gd1.0/Nd6.0/TiO2 NPs emerged as the most promising catalyst with an onset potential of -22 mV vs. RHE, a Tafel slope of 109 mV dec-1, and an exchange current density of 0.72 mA cm-2. Such HER electrochemical kinetic parameters are close to those recorded by the commercial Pt/C (onset potential: -15 mV, Tafel slope: 106 mV dec-1, and exchange current density: 0.80 mA cm-2), and also comparable with those measured by the most active electrocatalysts reported in the literature. The synergistic interaction of Gd and Nd is thought to be the major cause of the bimetallic catalyst's activity.

The photocatalytic biohydrogen generation using ZnO with the aid of simultaneous deposition of copper from an aqueous biomass-derivative glycerol solution was investigated. The effects of concentration of glycerol solution, Cu ion concentration and reaction temperature on biohydrogen generation were investigated. The photocatalytic biohydrogen production rate increased with increasing the concentration of aqueous glycerol solution, and the observed data could be fitted to the Langmuire-Hinshelwood kinetic models. The photocatalytic H2 production efficiency with ZnO could be significantly improved by simultaneous Cu deposition. The photocatalytic biohydrogen production rate was dependent on temperature, and increased with the increasing temperature. The possible mechanisms for oxidation of glycerol solution and photocatalytic hydrogen generation were proposed.

In this paper we propose a simple procedure to obtain multi-walled carbon nanotubes (MWCNT) decorated with TiO₂-Ag nanoparticles (MWCNT-TiO₂-Ag). MWCNT were decorated with TiO2-Ag via combined functionalisation with -OH and –COOH groups and polymer wrapping technique using poly(allylamine hydrochloride) (PAH). TiO₂ modified Ag nanoparticles were synthesized through Pechini method using mixture of acetylacetonate-modified titanium (IV) isopropoxide with silver nitrate (the Ag+/Ti4+ atomic ratio, is 0.5, 1,0, 1.5, 2.0 and 2.5 %, respectively) and the L(+)-ascorbic acid, as reducing agents. XRD analysis revealed the formation of nanocomposite containing CNT, TiO₂ (anatase and rutile) and Ag. By SEM was evidenced the presence of the nanoparticles on MWCNT surface. The increases of the ratio between Ag⁺ and Ti⁴⁺ decrease the band gap energy of the samples. In Raman spectra the characteristic vibration of the TiO₂, Ag and C atoms of graphite are identified. The photocatalytic activity of the MWCNT-TiO₂-Ag nanocomposite was assessed by examining the degradation of Allura red (E129) aqueous solution under UV irradiation. The dye photodegradation process follows a pseudo – first – order kinetic with respect to the Langmuir – Hinshelwood reaction mechanism.

Composites of Ag and TiO2 nanoparticles on cotton fabrics were synthetized in-situ by sono-chemical and hydrothermal methods achieving the successive formation of Ag-NPs and Ti-NPs directly on the fabric. The impregnated fabrics were characterized by ATR-FTIR spectroscopy, high resolution microscopy (HREM), scanning electron microscopy coupled with Ener-gy-dispersive X-ray spectroscopy (SEM-EDS), Raman, photoluminescence, UV-vis and DRS spectroscopies and by tension tests. Results showed the successful formation and impregnation of NPs on the cotton fabric, with a negligible leaching of NPs after several washing cycles. The photocatalytic activity of supported NPs was assessed by the degradation of methyl blue dye (MB) under solar and UV irradiation revealing improved photocatalytic activity of the Ag-TiO2/cotton composites due to a synergy of both Ag and TiO2 nanoparticles. This behavior is attributed to a diminished electron-hole recombination effect in the Ag-TiO2 cotton samples. The biocide activity of these composites on the growth inhibition of Staphylococcus aureus (Gram+) and Escherichia coli (Gram-) was confirmed, revealing interesting possibilities for the utilization of the functionalized cotton fabric as protective cloth for medical applications.

Owing to the escalating adoption of IoT systems across various domains, the demand for mobile and wireless power sources has surged. Although conventional batteries typically serve as energy storage components, the current low-power consumption devices necessitate eco-friendly alterna-tives. In this study, we designed, fabricated, and characterized an energy harvesting device that repurposes mechanical vibrations. A three-beam design was employed to harvest energy across a broader range of potential frequencies. Finite element models were simulated to ascertain the first bending moment for both sets of beams. A nanostructured piezoelectric multilayer film made of ZnO was deposited onto an AISI 304 steel substrate, and a photosensitive resin seismic mass was implemented. Low-cost techniques generating minimal environmental waste were leveraged in the fabrication process. The piezoelectric film was deposited using a spray nebulization technique involving recycled materials and cost-effective equipment. Micrographs of the layers unveiled the presence of nanospheres with diameters of 250 nm. Employing a custom-made shaker, output voltages of 1.08 V and 180 mV, and power outputs of 1.849 µW and 16.2 nW were achieved for each set of beams. The electrical characterization was conducted using a custom-made shaker, repurposing materials for this objective.

In this work, the adsorption and photocatalytic properties of ZnO-ZnAl2O4 nanosized composites synthesized by the polymer-salt method have been studied. To evaluate the efficiency of adsorption, experiments were carried out on the decolorization of aqueous solutions of the Chicago Sky Blue diazo dye. The adsorption process is divided into two stages, at the first stage the dye is rapidly adsorbed on the outer surface of the composite particles, at the second stage the dye diffuses into the pores of the material. It was noted that the rate of photocatalytic decomposition of the dye is higher than the rate of the adsorption process, which indicates the occurrence of photocatalytic decomposition of dye molecules both on the surface of the composites and in the liquid phase. With an increase in the light intensity, the photocatalytic process is significantly accelerated, linearly at low intensities, and at high intensities the dependence becomes a power law.

Microplastics (MPs) and nanoplastics (NPs) are distributed and transferred among the four major environmental compartments (air, water, soil, and biota) and have been already found in humans, making crucial to develop remediation technologies to tackle this kind pollution. Photocatalysis can be used to eliminate MPs present in contaminated wastewater effluents before their discharge into waterbodies. In this work, several green TiO2-based semiconductors were prepared using the extrapallial fluid (EPF) of Mytilus edulis sea water mussels as doping precursor. The semiconductors were then used as films or powders to photocatalytically degrade polystyrene (PS) NPs and MPs and polyethylene (PE) MPs. It was found that the obtention of green TiO2-based semiconductors with good characteristics for photocatalytic purposes (anatase crystalline phase, presence of porosity, activity in visible light and high surface area) seems not enough to achieve high degradation efficiency. The operational conditions of the reaction system should be also taken into account. For instance, the convenience of using semiconductors in the form of films can be overcome by their limited exposed surface area or the null adsorption of the semiconductor in the MPs particles. Additionally, crystallinity of the semiconductor can be a more determinant factor to take into account when performing photocatalysis of MPs.

The photocatalytic hydrogen evolution reaction (HER) by water splitting has been studied, using catalysts based on TiO2 nanowires (TiO2NWs), which were synthesized by a hydrothermal procedure. This nanomaterial was subsequently modified by incorporating different loadings of gold nanoparticles (AuNPs) on the surface, previously exfoliated MoS2 nanosheets, and CeO2 nanoparticles (CeO2NPs). These nanomaterials, as well as the different synthesized catalysts, were characterized by electron microscopy (HR-SEM and HR-TEM), XPS, XRD, Raman, Reflectance and BET surface area. HER studies were performed in aqueous solution, under irradiation at different wavelengths, which were selected through the appropriate use of optical filters. The results obtained show that there is a synergistic effect between the different nanomaterials of the catalysts. The specific area of the catalyst, and especially the increased loading of MoS2 and CeO2NPs in the catalyst substantially improved the H2 production. Recyclability studies showed only a decrease in activity of approx. 7% after 15 cycles of use, which opens many possibilities regarding the potential use and scaling of these heterostructures in photocatalytic production of H2 from water.

So far, poly(L-lactic acid), PLLA, nanosheets proved to be promising for wound healing. Such biodegradable materials are easy-to-prepare, bio-friendly, cost-effective, simple to apply and were shown to protect burn wounds and facilitate their healing. At the same time, certain metal ions are known to be essential for wound healing, which is why this study was motivated by the idea of incorporating PLLA nanosheets with Zn2+ ion containing nanoparticles. Upon being applied on wound, such polymer nanosheets should release Zn2+ ions, which is expected to improve wound healing. The work thus focused on preparing PLLA nanosheets embedded with several kinds of Zn-containing nanoparticles, their characterization and ion-release behavior. ZnCl2 and ZnO nanoparticles were chosen as model particles with different solubility in water, both types showing similar ion release dynamics in liquid medium with pH around 7.4.

Read-Across Structure-Activity Relationship (RASAR) is an emerging cheminformatic approach that combines the usefulness of a QSAR model and similarity-based Read-Across predictions. In this work, we have generated a simple, interpretable, and transferable quantitative-RASAR (q-RASAR) model which can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials. The data set involves 29 TiO2-based nanomaterials which contain specific amounts of noble metal precursors in the form of Ag, Au, Pd, and Pt. The data set was rationally divided into training and test sets and the Read-Across-based predictions for the test set were generated using the tool Read-Across-v4.1 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. The hyperparameters were optimized based on the training set data and using this optimized setting, the Read-Across-based predictions for the test set were obtained. The optimized hyperparameters and the similarity approach, which yields the best predictions, were used to calculate the similarity and error-based RASAR descriptors using the tool RASAR-Desc-Calc-v2.0 available from https://sites.google.com/jadavpuruniversity.in/dtc-lab-software/home. These RASAR descriptors were then clubbed with the physicochemical descriptors and were subjected to features selection using the tool Best Subset Selection v2.1 available from https://dtclab.webs.com/software-tools. The final set of selected descriptors was used to develop multiple linear regression based q-RASAR models, which were validated using stringent criteria as per the OECD guidelines. Finally, a random forest model was also developed with the selected descriptors. The final machine learning model can efficiently predict the cytotoxicity of TiO2-based multi-component nanomaterials superseding previously reported models in the prediction quality.

ZnO was synthesized by Sol gel method using zinc nitrate as precursor at different calcination temperatures. Nucleation of ZnO crystallites and their growth with rise in temperature was observed. Exciton bands and lattice imperfections affected the absorption spectra. The decrease in band gap with temperature was due to the formation of defect energy levels. Phonon assisted non-radiative transitions caused broadening of the peaks. The possibility of tuning the band gap of ZnO by changing the temperature was explored. Simulation studies showed transition to single phase with rise in temperature.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Zinc oxide (ZnO) has been widely studied over the last decade for its remarkable properties in optoelectronic and photovoltaic devices because of its high electron mobility and excitonic properties, probably the broadest range of nanostructured forms, and their ease and low cost of synthesis by a wide variety of methods. The volume of recent work on ZnO nanostructures and their devices can potentially overshadow significant developments in the field. Therefore, there is a need for a concise description of the most recent advances in the field. In this review, we focus on the effect of ZnO nanostructure morphologies on the performance of ZnO-based solar cells sensitized using methylammonium lead iodide perovskite. We present an exhaustive discussion of the synthesis routes for different ZnO nanostructure morphologies, ways to control the morphology, and the impact of morphology on the photo-conversion efficiency of a given PSC.

Electron-hole recombination and narrow range utilization of sunlight limit the photocatalytic efficiency of TiO2. We synthesized a carbon dots (CDs) modified TiO2 nanoparticles (NPs) with flower-like mesoporous structure, i.e., porous TiO2/CDs nanoflowers. Among such hybrid parti-cles, CDs worked as photosensitizers for the mesoporous TiO2 and enabled the resultant TiO2/CDs nanoflowers with a wide-range light absorption. Rhodamine B (Rh-B) was employed as a model organic pollutant to investigate the photocatalytic activity of the TiO2/CDs nanoflowers. The results demonstrated that the decoration of CDs on both TiO2 nanoflowers and P25 NPs enabled a significant improvement of the photocatalytic degradation efficiency compared with the pristine TiO2. TiO2/CDs nanoflowers with porous structure and larger surface areas than P25 showed a higher efficiency owing to prevent local aggregation of carbon materials. All the results revealed that the introduced CDs and the unique mesoporous structure, large surface areas and loads of pore channels of the prepared TiO2 NPs played important roles in the enhancement of the photocatalytic efficiency of the TiO2/CDs hybrid nanoflowers. Such TiO2/CDs composite NPs also opens a door for photodegradation, photocatalytic water splitting and enhanced solar sun-light as light source.

High purity TiO2 and CuO powders were synthesized by the Pechini method, an inexpensive and easy-to-implement procedure to synthetize metal oxides. The variables of synthesis were the ethylene glycol:citric acid molar ratio and the pH. High reproducibility of the anatase and tenorite phase was obtained for all synthesis routes. The degree of purity of the powders was confirmed by XRD, FTIR, UV-vis absorption and XPS spectra. SEM and TEM images revealed the powders are composed by micrometer grains that can have a spherical shape (only in the TiO2) or formed by a non-compacted nanocrystalline conglomerate. FTIR spectra only vibrational modes associated to the TiO2 or CuO with a nanoparticle behavior. UV-vis absorption spectra revealed the values of maximum absorbance percentage of both systems are reached in the ultraviolet region, with percentages above 83 % throughout the entire visible light spectrum for the CuO system, a relevant result for solar cell applications. Finally, XPS experiments allow the observation of the valence bands and the calculation of the energy bands of all oxides.

In this paper, the phases in the Mg-Ti-O system using the 1:1 formulation of MgO:TiO2 mixing synthetic brucite of Mexican origin with TiO2 microparticles of high purity and with a heat treatment at 1100°C for 1 h were studied. The raw materials and formulation by XPS and DRX techniques were characterized. The results demonstrate the presence of different oxidation states in titania and the formation of different oxides in the Mg-Ti-O system when mixed and calcined at 1100°C; additionally, the formation of vacancies in the crystal lattice during the transformation from hexagonal brucite to magnesia with a cubic structure centered on the faces is estimated. With the results, its thermal behavior is warned based on the MgO-TiO2 phase diagram.

The photocatalytic degradation of two quinolone-type antibiotics (ciprofloxacin and levofloxacin) in aqueous solution was studied, using catalysts based on ZnO nanoparticles, which were synthesized by a thermal procedure. The efficiency of ZnO was subsequently optimized by incorporating different co-catalysts of gC3N4, reduced graphene oxide and nanoparticles of gold. The catalysts were fully characterized by electron microscopy (TEM and SEM), XPS, XRD, Raman, and BET surface area. The most efficient catalyst was 10%Au@ZnONPs-3%rGO-3%gC3N4, allowing to obtain degradations of both pollutants above 96%. This catalyst has the largest specific area, and its activity has been related to a synergistic effect, involving factors as relevant as the surface of the material and the ability to absorb radiation in the visible region, mainly produced by the incorporation of rGO and gC3N4 to the semiconductor. The use of different scavengers during the catalytic process, was used to establish the possible photodegradation mechanism of both antibiotics.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

Direct interaction with the neuronal cells is a prerequisite to deciphering useful information in understanding the underlying causes of diseases and functional abnormalities in the brain. Precisely fabricated nanoelectrodes provide the capability to interact with the brain in its natural habitat without compromising its functional integrity. Considerable research has been focused on the employment of vertical nanotubes as nanoelectrodes due to large-scale intracellular recording capability and longer-term intracellular access that arise from their unique geometry. Despite many types of nanotube structures reported in the literature, a limited subset of the nanotubes has been investigated for neural interfacing. This work reports on the fabrication and optimisation of vertically oriented titania nanotube arrays as a scalable electrode platform for neural interface application. To this end, the doping was performed by incorporating a selected group of biologically active metallic ions, including zinc, strontium, and copper, into TiO2 lattice and its effect was studied with respect to the structural, electrochemical and biological properties of the nanotube arrays. It was found that doping can change the length, diameter and wall thickness of the nanotubes. Among pure and doped samples, the copper-doped TiO2 nanotubes demonstrated the highest electrochemical and biological performance. Our results suggest that the doping can be used as a promising method to optimise the properties of nanotube arrays for the development of high-performance neural electrodes.

Titanium and its alloys are used biomaterials for medical and dental applications, due to their mechanical and physical properties. The surface modifications of titanium with bioactive molecules can increase the osseointegration by improving the interface between the bone and implant. Titanium dioxide nanotubes (TiO₂NTs) have excellent bioactivity inducing cell adhesion, spreading, growth and differentiation. In this work, TiO₂NTs were functionalized with a lectin from the plasma of the fish Oreochromis niloticus aiming to favour the adhesion and proliferation of osteoblast-like cells, improving its biocompatibility. The TiO₂NTs were obtained by anodization of titanium and annealed at 400 °C for 3 h. The resulting TiO₂NTs were characterized by high-resolution scanning electron microscopy. The successfully incorporation of OniL on the surface of TiO₂NTs by spin coating was demonstrated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIE) and attenuated total reflection-Fourier transform infrared spectrum (ATR-FTIR). Our results showed that TiO₂-NTs were successfully synthesized in a regular and well-distributed way. The functionalization of TiO₂-NTs with OniL favoured adhesion, proliferation, and the osteogenic activity of osteoblast-like cells, suggesting its use to improve the quality and biocompatibility of titanium-based biomaterials.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Renewable methanol, obtained from CO₂ and hydrogen provided from renewable energy, has been proposed as a way to close the CO₂ loop. In industry, methanol synthesis using the catalyst CuO/ZnO/Al₂O₃ occurs at a high pressure. We intend to make certain modification on the traditional catalyst in order to work at lower pressure, maintaining high selectivity. Therefore, three heterogeneous catalysts have been synthesized by co-precipitation in order to improve the activity and the selectivity to methanol under mild conditions of temperature and pressure. Certain modifications on the traditional catalyst Cu/Zn/Al₂O₃ were employed such as the modification of the synthesis time and the addition of Pd as a dopant agent. The most efficient catalyst among those tested was a palladium-doped catalyst, 5% Pd/Cu/Zn/Al₂O₃. This had a selectivity of 64% at 210C and 5 bar.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

The photocatalysis process over N-doped TiO2 under visible light is examined for Pb(II) oxidation to form the less toxic and handleable PbO2 suggesting a new method for Pb(II) remediation. The doping TiO2 with N element was conducted by simple hydrothermal technique and using urea as the N source with various concentrations. The doped photocatalysts were characterized by DRUVS, XRD, FTIR and SEM-EDX instruments. Photocatalysis of Pb(II) through batch experiment was performed for evaluation of the doped TiO2 activity under visible light, with applying various fractions of N doped, photocatalyst weigh, irradiation time, and solution pH. The research results attributed that N doping has been successfully performed, that shifted TiO2 absorption into visible region, allowing it to be active under visible irradiation. The photocatalytic removal of Pb(II) under visible ligth over N-TiO2 showed more effective than that of over the un-doped photocatalyst. The removal of Pb(II) has notably taken place through oxidation, that may form PbO2. The highest photocatalytic oxidation of Pb(II) 15 mg/L in 25 mL of the solution could be reached by using TiO2 doped with 10%w of N, 15 mg of N-TiO2 weight, 30 minutes of time, and at pH 8, suggesting a feseable method for Pb(II) remediation.

Abstract The construction of a heterostructured nanowire array allows the manipulation of the interfacial, surface, charge transport, and transfer properties simultaneously, offering new opportunities to achieve multi-functionality for various applications. Herein, we developed a facile thermal evaporation and post-annealing method to synthesize ternary-Zn2SnO4/binary-ZnO radially heterostructured nanowire arrays (HNA). Vertically aligned ZnO nanowire arrays (3.5 μm in length) were grown on a ZnO-nanoparticle-seeded fluorine-doped tin oxide substrate by a hydrothermal method. Subsequently, the amorphous layer consisting of Zn-Sn-O complex was uniformly deposited on the surface of the ZnO nanowires via the thermal evaporation of the Zn and Sn powder mixture in vacuum, followed by post-annealing at 550 °C in air to oxidize and crystallize the Zn2SnO4 shell layer. The use of a powder mixture composed of elemental Zn and Sn (rather than oxides and carbon mixture) as an evaporation source ensures high vapor pressure at a low temperature (e.g., 700 °C) during thermal evaporation. The morphology, microstructure, and charge-transport properties of the Zn2SnO4/ZnO HNA were investigated by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, transmission electron microscopy, and electrochemical impedance spectroscopy. Notably, the optimally synthesized Zn2SnO4/ZnO HNA shows an intimate interface, high surface roughness, and superior charge-separation and -transport properties compared with the pristine ZnO nanowire array.

Zinc oxide (ZnO) nanoparticles (NPs) were synthesized using Rosmarinus officinalis leaf extract at 80 ° C (ZnO-80) and 180 ° C (ZnO-180). The biosynthesized ZnO NPs were characterized and their photocatalytic activity was evaluated for the degradation of methylene blue (MB) and crystal violet (CV) under sunlight irradiation. The results of the characterizations by XRD, TEM and SEM showed that the size of the NPs of ZnO-80 was smaller than that of ZnO-180 which exhibited flakier agglomerated spherical structures. Photocatalytic tests showed ZnO-80 which was prepared by a cheap and easy procedure compared to ZnO-180 effectively degrades MB and CV dyes under sunlight. The superior performance of ZnO-80 over ZnO-180 can be explained by the differences in their textural properties. This is because ZnO-80 has a smaller crystallite size, a specific surface area and a higher pore volume than ZnO-180. Fourier-transform infrared spectroscopy (FTIR) analyzes revealed that both samples contained an adsorbed carboxylate group (COO-), and accordingly a mechanism was proposed for the formation of ZnO NPs that include the carboxyl group.

ZnO has many technological applications which largely depend on its properties that can be tuned by controlled synthesis. Ideally, the most convenient ZnO synthesis is carried out at room temperature in aqueous solvent. However, the correct temperature values are often loosely defined. In the current paper we performed synthesis of ZnO in aqueous solvent, by varying reaction and drying temperature by 10°C steps and monitored the synthesis products primarily by XRD. We found out that a simple direct synthesis of ZnO, without additional surfactant, pumping of freezing, required both a reaction (TP) and a drying (TD) temperature of 40°C. Higher temperatures also afford ZnO, but lowering any of the TP or TD below the threshold value results either in the achievement of Zn(OH)2 or in a mixture of Zn(OH)2/ZnO. A more detailed Rietveld analysis of the ZnO samples reveals a density variation with the synthesis temperature and an increase of the nanoparticles average size also verified by SEM images. The optical properties of ZnO obtained by UV-Vis reflectance spectroscopy indicate a red shift of the band gap by ~0.1 eV.

TiO₂ nanorod as a superior nanostructure has attracted a lot of attention to exert in the photocatalytic and photoelectrocatlytic applications in recent years. Nevertheless, its practical usage is restricted by a number of limitations such as the large band gap energy, the low rate of photo-induced carriers generation and the high rate of charge carriers recombination. Therefore in this study, incorporation of TiO₂ nanorod with WO₃ is proposed as a suitable approach to overcome these defects. In this regard, WO₃-TiO₂ nanorod was constructed by a facile one pot hydrothermal method in two incessant steps and was then employed as a potent photoanode for photoelectrocatalytic hydrogen generation. The morphology, elemental compositions and optical properties were characterized by the FESEM, EDS and DRS analysis, respectively. Furthermore, voltammetry analyses were performed to assay the photoelectrochemical features of WO₃-TiO₂ nanorod. The results confirmed that the incorporation of TiO₂ nanorod with WO₃ not only significantly made the band gap energy narrower (from 3eV to 2eV), but also dramatically intensified the photocurrent density and photoconversion efficiency from 1mA.cm^-2 to 1.8mA.cm^-2 and from 0.3% to 0.45%, respectively. As a consequence of improving optical properties and photoelectrochemical features, WO₃-TiO₂ nanorod could generate 2.43 mmol H₂ during 100 min under UV irradiation, which was 1.71 times more than hydrogen generated over pure TiO₂ nanorod

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

MoS₂/TiO₂ nanostructures made of MoS₂ nanoparticles covering TiO₂ nanosheets have been synthesized, either via ex-situ or in-situ approaches. Morphology and structure of MoS₂/TiO₂ hybrid nanostructures have been investigated and imaged by means of X-ray diffraction (XRD) analysis and high-resolution transmission electron microscopy (HRTEM), while the vibrational and the optical properties have been investigated by Raman, Fourier-transform infrared spectroscopy (FTIR) and UV−visible (UV-Vis) techniques. The different stacking degrees together with the size distribution of the MoS₂ nanosheets, decorating the TiO₂ nanosheets, have been carefully obtained from HRTEM images. The nature of the surface sites on the main exposed faces of both materials has been detected by means of in-situ FTIR spectra of adsorbed CO probe molecule. The results coming from the ex-situ and in-situ approaches will be compared, by highlighting the role of the synthesis processes in affecting morphology and structure of MoS₂ nanosheets, including their curvature, surface defects, and stacking order. Some more, it will be shown that the in-situ approach is affecting the reactivity of the TiO₂ nanosheets too, hence in turn affects the MoS₂/TiO₂ nanosheets interaction.

Wound infections evidently appeared in times of World War I that accounted a significant mortality and morbidity rate among injured soldiers. Currently, around 11 million people worldwide require medical treatment for wound infections and 300,000 die every year due to untreated wound infection. The extensive use of antibiotics to treat wound infection leads to emerging new microbial strains that are resistant to many antibiotics. There is a growing concern on the emergence and re-emergence of drug-resistant pathogens such as multi-resistant bacterial strains. Hence, the development of new antimicrobial compounds or the modification of those that already exist to improve antibacterial activity is a high priority area of research. During the past few decades, nanotechnology has arisen with new promising technology for synthesis of nanobiomaterials. Metallic nanoparticles (NPs) are considered as new alternative treatment with superior antibacterial activity. In this study, new formulation of titanium oxide (TiO2) NPs with different sizes were synthesized and characterized. Genotoxicity, mutagenicity and antibacterial activities of TiO2 NPs against the causative agents of wound infection were investigated. Antibacterial activity of TiO2 NPs was conducted against three ATCC ® bacterial strains: methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Pseudomonas aeruginosa. The results clearly illustrate a superior antibacterial activity of all newly formulated TiO2 NPs against the most causative agents of wound infection. Most of our TiO2 NPs showed non-genotoxic and non-mutagenic results at the maximum concentrations. Findings of this study will enhance the future of the therapeutic strategies against the resistant pathogenic strains that cause wound infections.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

In this research, first a binary nanocomposite of magnetic recyclable photocatalyst Fe₃O₄/TiO₂, was synthesized by sol gel technique. Then, in order to enhance the photocatalytic activity of the synthesized nanocomposite, it was deposited by silver nanoparticles for using in degradation of organic pollutants 2, 4-dichlorophenol (2, 4-DCP) under visible light. A range of analytical techniques including XRD, FESEM/EDX, DRS, VSM and N₂ physisorption were employed to reveal the crystal structure, morphology and property of the nanocomposites. We obtained 32% and 55% degradation of 2, 4-DCP under visible light after 180 min irradiation in the presence of Fe₃O₄/TiO₂ and Fe₃O₄/TiO₂/Ag respectively. Thus, the excellent visible light photocatalytic activity of Fe₃O₄/TiO₂/Ag sample can be attributed to the surface plasmon resonance effect of Ag nanoparticles deposited on Fe₃O₄/TiO₂ nanocomposite.

Herewith we report a facile synthesis of zinc oxide doped with (5, 10, 15, and 20 wt%) titanium oxide nanocomposites in gelatin under ultra-sonication. The X-ray diffraction (XRD) data revealed ZnO the formation in addition to a rutile phase TiO2. The ZnO phase size decreased, and the rutile TiO2 phase increased with a TiO2 loading increment. The scanning electron microscopy (SEM) displayed a combination of spherical and hexagonal particles with a 60 – 80 nm size distribution. The prepared nanostructures photocatalytic activity was assisted using Rhodamine B dye, where they showed enhanced photodegradation competence under visible light irradiation. The kinetics of photodegradation followed the first-order kinetics with the 20 % wt sample having the maximum activity. The mechanistic investigation revealed the dominance of h+ and •O2- species during the dye photodegradation. The results indicate the potential application of such gelatin stabilized nanostructures for dye illumination from aqueous solutions under sunlight.

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

The size of TiO2 (either nanometric or micrometric) can significantly affect both its photocatalytic and photoelectrochemical properties, thus altering the photooxidation of organic pollutants in air or water. The purpose of this work is to give an account of the photoelectrochemical and photocatalytic features of some nano- and micro-sized TiO2 commercial powders towards a model reaction, the photooxidation of acetone. Cyclic voltammograms (CV) of TiO2 particulated electrodes under UV illumination experiments were carried out in either saturated O2 or N2 solutions for a direct correlation with the photocatalytic process. In addition, the effect of different reaction conditions on the photocatalytic efficiency under UV light in both aqueous and gaseous phases was also investigated. CV curves with the addition of acetone under UV light showed a negative shift of the photocurrent onset, confirming the efficient transfer of photoproduced reactive oxygen species (ROSs), e.g., hydroxyl radicals, or holes to acetone molecules. The photocatalytic experiments showed that the two nano-sized samples exhibit the best photocatalytic performance. The different photoactivity of the micro-sized samples is probably attributed to their morphological differences, affecting both the amount and distribution of free ROSs involved in the photooxidation reaction.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

The TiO₂ nanostructures resulted by pyrolysis of TiCl₄ at low temperature of 80 ^oC are found to be a mixture of amorphous TiO₂ complexes and anatase nanostructure whose ratio depends on the pH of the pyrolysis medium. At low pH level, the resulting TiO₂ nanostructure is predominant anatase and gradually shifts to the amorphous TiO₂ complexes with pH level increasing. By means of heat treatment, the amorphous TiO₂ complexes can be converted back to the anatase nanostructure and then transform to rutile with the elevating temperature. Amongst of the TiO₂ nanostructure recovered from amorphous TiO₂ complexes, the anatase shows to be the most effective photocatalyst in decomposition of methylene blue.

In this changing world, we all are surrounded by the surmountable risk of getting injured. Amongst various risk factors, major burns are the most distressing and catastrophic. Burn wounds are not easy to heal via natural healing process and ultimately ended up with scar formation. If the degree of burn is high then the loss of tissue and its function is very common. To fasten-up the natural burn wound healing; zinc, an essential trace element is found to be very much effective. But due to its’ particle size limitation, less contact with wounded cells and tissues, and high inherent toxicity restrict its use. Needlessly, zinc is an element with dual action i.e. both antimicrobial and wound healing it is a prime choice to apply its aptitude in burn wound healing. To overcome the documented limitations zinc has converted to nanoparticle form. Zinc oxide nanoparticles, in particular, have attained ample of interest due to their unique properties and potential antimicrobial activity along with wound healing activity which makes it promising for the healing of topical burn wounds. Plant mediated green synthesis of nano-metal oxide particles is gaining a lot of significance due to its simplicity, eco-friendliness and extensive antimicrobial activity and recommended as an appealing substitute to not only physical methods but also chemical methods avoiding the use of the high rate of toxic chemicals and extreme surroundings. This study includes ZnO NPs role in burn wound healing with Phyto-mediated synthesis methods to provide evidence of their potential applications. Additionally, it provides an overview of traditional methods used for the synthesis of ZnO nanoparticles and characterization techniques to obtain information concerning the size, shape and optical properties along with toxicity and safety concern of ZnO NPs and its biomedical applications.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

For some decades, the scientific community has been looking for alternatives to the use of fossil fuels that allow the planet's sustainable and environmentally friendly development. To do this, attempts have been made to mimic some processes that occur in nature, among which the photosystem-II stands out, which allows water splitting operating with different steps to generate oxygen and hydrogen. This research presents promising results using synthetic catalysts, which try to simulate some natural processes, and which are based on Au@ZnO-graphene compounds. These catalysts were prepared by incorporating different amounts of gold nanoparticles (1 wt.%, 3 wt.%, 5 wt.%, 10 wt.%) and graphene (1 wt.%) on the surface of synthesized zinc oxide nanowires (ZnO NWs), and zinc oxide nanoparticles (ZnO NPs), along with a commercial form (commercial ZnO) for comparison purposes. The highest amount of hydrogen (1,127 µmol/hg) was reported by ZnO NWs with a gold and graphene loadings of 10 wt.% and 1 wt.%, respectively, under irradiation at 400 nm. Quantities of 759 µmol / hg and 709 µmol / hg were obtained with catalysts based on ZnO NPs and commercial ZnO, respectively. The photocatalytic activity of all composites increased with respect to the bare semiconductors, being 2.5 times higher in ZnO NWs, 8.8 times for ZnO NPs and 7.5 times for commercial ZnO. The high photocatalytic activity of the catalysts is attributed, mainly, to the synergism between the different amount of gold and graphene incorporated, and the surface area of the composites.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

In this research we are reporting gas sensing properties of TiO_2-x/TiO₂-based hetero-structure, which was ‘self-heated’ by current that at constant potential passed through the structure. Amperometric measurements were applied for the evaluation of sensor response towards ethanol, methanol, n-propanol and acetone gases/vapors. The sensitivity towards these gases was based on electrical resistance changes, which were determined by amperometric measurements of current at fixed voltage applied between Pt-based contacts/electrodes deposited on TiO_2-x/TiO₂-based layer. XRD analysis revealed the formation of TiO_2-x/TiO₂-based hetero-structure, which is mainly based on Ti₃O₅/TiO₂ formed during hydro-thermal oxidation based sensing layer preparation process. Additionally, photoluminescence and time-resolved photoluminescence decay kinetics based signals of this sensing structure revealed the presence of TiO₂ mainly in the anatase phase in the TiO_2-x/TiO₂-based hetero-structure, which was formed at 400°C annealing temperature. The evaluation of TiO_2-x/TiO₂-based gas sensing layer was performed at several different temperatures (25°C, 72°C, 150°C, 180°C) and at these temperatures different sensitivity to aforementioned gaseous materials was determined.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

In this work, cobalt doped ZnO nanorod arrays with anticorrosion function were successfully prepared on FTO substrate by a simple aqueous solution method. XRD and EDS results indicate the doped Co2+ has successfully incorporated into the ZnO crystal lattice. Photocurrent density and open circuit potential (OCP) results indicate the photocathodic protection performance for 316 stainless steel (316 SS) and Q235 carbon steel in 3.5 wt.% NaCl solution under 300 W Xe lamp enhanced with the increase of cobalt concentration, and the photoanode with 15% Co/Zn ratio has the optimal photocathodic protection effect. The mechanism of enhancement may be result from the narrowed band gap, the lower recombination rate of photogenerated electron-holes, the intermediate impurity level and the split of the hypo-outer shell of cobalt ions.

Photoelectrocatalytic water splitting by using various TiO₂ nanostructures is a promising approach to generate hydrogen without harmful byproducts. However, their effective performance is restricted by some drawbacks such as high rapid electron-hole pair recombination and backward reaction producing H₂O. Thus in this study, the probability of enhancing hydrogen generation rate by adding methanol as a sacrificial agent to the anodic chamber of a two-compartment photoelectrochemical cell is investigated. Herein, one-dimensional elongated TiO₂ nanorods that were fabricated via a facile one-pot hydrothermal method are utilized as potent photoanode. Voltammetric characterizations confirm that addition of alcoholic sacrificial agent has a significant effect on photoelectrochemical properties of TiO₂ nanorods which by adding 10 wt% of methanol, the photocurrent density and photoconversion efficiency increased from 0.8mA.cm^-2 to 1.5mA.cm^-2 and from 0.28% to 0.45%, respectively. The results of photoelectrocatalytic water splitting indicated that the hydrogen generation rate in the presence of methanol was about 1.2 times higher than that from pure water splitting. These enhancements can be attributed to the key role of methanol. Methanol molecules not only inhibit the electron-hole pair recombination but also accelerate the hydrogen generation rate by sharing their hydrogen atoms.

In this work, TiO₂ QDs modifed NiO nanosheets was employed to imporve the room-temperature NO₂ sensing properties of NiO. The gas-sensing studies showed that the response of nanocomposites with the optimal ratio to 60 ppm NO₂ was nearly 10 times larger than that of bare NiO, exhibiting potential application in gas-sensing. Considering the commonly reported immature mechanism that the effective charge transfer between two phases contribute to enhanced sensitivity, QDs sensitization mechanism was further detailed by designing a seirs of contrast experiments. First, the important role of QDs size effect was revealed by comparing a little enhanced sensitivity of TiO₂ particle-modified NiO with largely enhanced senstivity of TiO₂ QDs-NiO. Second, and more important, the direct evidence of heterointerface charge transfer efficiency was detailed by extracted interface bond (Ti-O-Ni) using XPS peak fitting. We hope this work can provide guideline to design more QDs-modified nanocomposites with the higher sensitivty for practical application.

The preparation of immobilized graphene–based photocatalyst layers is highly desired for environmental applications. In this study, the preparation of an immobilized reduced graphene oxide (rGO)/TiO₂ composite by electrophoretic deposition (EPD) was optimized. It enabled quantitative deposition without sintering and without the use of any dispersive additive. The presence of rGO had beneficial effects on the photocatalytic degradation of 4-chlorophenol in an aqueous solution. A marked increase in the photocatalytic degradation rate was observed, even at very low concentrations of rGO. Compared with the TiO₂ and GO/TiO₂ reference layers, use of the rGO/TiO₂ composite (0.5 wt% of rGO) increased the first-order reaction rate constant by about 70%. This enhanced performance was due to the increased formation of hydroxyl radicals that attacked the 4-chlorophenol molecules. The direct charge transfer mechanism had only limited effect on the degradation. Thus, EPD-prepared rGO/TiO₂ layers appear to be suitable for environmental application.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.