Background: Instrument-assisted soft tissue mobilization (IASTM) is thought to alter fluid dynamics in human soft tissue. The aim of this study was to investigate the influence of IASTM on the thoracolumbar fascia (TLF) on the water content of the lumbar myofascial tissue. Methods: 21 healthy volunteers were treated with IASTM. Before and after the procedure and 5 and 10 minutes later, lumbar bioimpedance was measured by bioimpedance analysis (BIA) and TLF stiffness by indentometry. Tissue temperature was recorded at the measurement time points using an infrared thermometer. Results: Bioimpedance increased significantly from 58.3 to 60.4 Ω (p < 0.001) at 10-minute follow-up after the treatment. Temperature increased significantly from 36.3 to 36.6° Celsius from 5 to 10 minutes after treatment (p = 0.029), while lumbar myofascial stiffness did not change significantly (p = 0.84). Conclusions: After the IASTM intervention, there was a significant increase in bioimpedance, likely due to a decrease in water content in myofascial lumbar tissue. Further studies in a randomized control trial design are needed to extrapolate the results in healthy subjects to a symptomatic population as well and to confirm the reliability of BIA in myofascial tissue.

Robot-assisted gait training (RAGT) is a promising treatment for stroke rehabilitation. Although the coordination between the upper and lower limbs is important for locomotor training, commercially available robotics for gait training mainly focus on the restoration of lower limb function. We aimed to evaluate the feasibility and usability of complex upper and lower limb RAGT in stroke patients using the GTR-A®, end effector-type robotic device. Patients with subacute stroke (N=9) received 30-minute RAGT thrice a week for two weeks (six sessions). Functionally, the hand grip strength (HGS), Functional Ambulatory Categories, modified Barthel Index, muscle strength test sum score, Berg Balance Scale, Timed Up and Go test, and Short Physical Performance Battery were used. The heart rate and a structured questionnaire were used to evaluate cardiorespiratory fitness and the usability of RAGT. Among the nine patients, all functional parameters between the baseline and post-training were significantly improved after RAGT, except for HGS and the muscle strength test. The questionnaire’s mean scores for each domain were as follows: safety 4.40±0.35, effects 4.23±0.31, efficiency 4.22±0.77, and satisfaction 4.41±0.25. The GTR-A® is a feasible and safe robotic device for patients with gait impairment after stroke. It showed functional improvement with endurance training effects.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

Background: Elucidation of epigenetic mechanisms correlating with neuropathic pain in humans is crucial for the prevention and treatment of this treatment-resistant pain state. In the present study, associations between neuropathic pain characteristics and DNA methylation of the transient receptor potential ankyrin 1(TRPA1) gene were evaluated in chronic pain patients and preoperative patients. Methods: Pain and psychological states were prospectively assessed in patients who suffered chronic pain or were scheduled for thoracic surgery. Neuropathic characteristics were assessed using the Douleur Neuropathique 4 (DN4) questionnaire. DNA methylation levels of the CpG island in the TRPA1 gene were examined using whole blood. Results: Forty-eight adult patients were enrolled in this study. Increases in DNA methylation rates at CpG -51 showed positive correlations with increases in the DN4 score both in preoperative and chronic pain patients. Combined methylation rates at CpG -51 also significantly increased together with increase in DN4 scores. Conclusions: Neuropathic pain characteristics are likely associated with methylation rates at the promoter region of the TRPA1 gene in human peripheral blood.

Study question: What are the current trends of research in Human Assisted Reproduction around the world? Summary answer: USA is the leading country, followed by the UK, China, France and Italy. The largest research area is “laboratory techniques”, although other areas such as “public health”, “quality, ethics and law” and “female factor” are gaining ground worldwide. What is known already: Scientific research, especially in health and medical sciences, aims at addressing specific needs that society (and, especially, patients) perceives as pressing. One of the main challenges for policymakers and research funders alike is therefore to align research priorities to societal needs. We can thus think of research agendas in terms of a demand side (societal needs) and a supply side (research outputs). Research output in Human Assisted Reproduction has expanded in the past years, as indicated by the increasing number of scientific publications in indexed journals in this area. Nevertheless, no map of research related to assisted reproduction has been produced so far, hindering the identification of potential areas of improvement and need. Study design, size, duration: 26,000+ scientific publications (articles, letters, and reviews) on Human Assisted Reproduction produced worldwide between 2005 and 2016 were analyzed. These publications were indexed in PubMed or obtained from reference list of indexed publications included in the analysis.Participants/materials, setting, methods: The corpus of publications was obtained by combining the MeSH terms: “Reproductive techniques”, “Reproductive medicine”, “Reproductive health”, “Fertility”, “Infertility”, and “Germ cells”. Then it was analyzed by means of text mining algorithms (Topic Modeling (TM) based on Latent Dirichlet Allocation (LDA)), in order to obtain the main topics of interest. Finally, these categories were analyzed across world regions and time. Main results and the role of chance: We identified 44 main topics, which were further grouped in 11 macro categories, form larger to smaller: “laboratory techniques”, “male factor”, “quality, ethics and law”, “female factor”, “public health and infectious diseases”, “basic research and genetics”, “pregnancy complications and risks”, “general infertility and ART”, “psychosocial aspects”, “cancer”, and “research methodology”. The USA was the leading country in number of publications, followed by the UK, China, France and Italy. Interestingly, research contents in high income countries is fairly homogeneous across macro-categories, and it is dominated by “laboratory techniques” in Western and Southern Europe, and by “quality, ethics and law” in North America, Australia and New Zealand. In middle income countries we observe that research is mainly performed on “male factor”, and noticeably less on “female factor”. Finally, research on “public health and infectious diseases” predominates in low-income countries. Regarding temporal evolution of research, “laboratory techniques” is the most abundant topic on a yearly basis, and relatively constant over time. However, since production in most of the other categories is increasing, the relative contribution of this research category is actually decreasing. Publication is especially increasing in “public health and infectious diseases” (in all world regions, but especially in low income countries), “quality, ethics and law” (high income countries), and “female factor” (middle income countries). Limitations, reasons for caution: Three main factors might limit the robustness of our work: the textual corpus analyzed is based on abstract and titles, the reproducibility of the stochastic algorithms applied, which may produce slightly differing results at each run, and the interpretation of the topics obtained. Wider implications of the findings: This study should prove beneficial in the design of research strategies and policies that foster the alignment between supply (assisted reproduction research) and demand (society). Study funding/competing interest(s): PTQ-14-06718 of the Spanish MINECO Torres Quevedo programme (FAM).

This paper investigates the problem of the optimal arrangement for both UAVs’ caching contents and service locations in UAV-assisted networks based on the context awareness, which considers the influence between users and environment. In the existing work, users within the coverage of UAVs are considered to be served perfectly, which ignores the communication probability caused by line-of-sight (LOS) and non- line-of-sight (NLOS) links. However, the links are related to UAV deployment. Moreover, the transmission overhead should be taken into account. To balance the tradeoff between these two factors, we design the ratio of users’ probability and transmission overhead as the performance measure mechanism to evaluate the performance of UAV-assisted networks. Then, we formulate the objective for maximizing the performance of UAV-assisted networks as a UAV-assisted caching game. It is proved that the game is an exact potential game with the performance of UAV-assisted networks serving as the potential function. Next, we propose the log-linear caching algorithm (LCA) to achieve the Nash equilibrium (NE). Finally, related simulation results reflect the great performance of the proposed algorithm.

myfood24 is a comprehensive self-completed online 24-hour dietary recall tool currently used for nutritional assessments in epidemiological research. However, its clinical application has been unexplored. This mixed methods prospective observational study explores the acceptability and usability of myfood24 in a clinical population, women with gestational diabetes (GDM). Women were recruited at their first diabetes antenatal clinic appointment. To assess acceptability and usability, they were asked to complete five 24-hour dietary recalls using myfood24 over two weeks and a user experience questionnaire; with a subset invited to participate in a one-to-one semi-structured interview. Of the 199 participants, mean maternal age was 33 years, mean booking BMI 29.7kg/m2, 36% primiparous, 57% White, 33% Asian. Of these 121 (61%) completed myfood24 at least once and 73 (37%) completed the user questionnaire; 15 were interviewed. Usability of myfood24 was measured using the System Usability Scale (SUS) and found to be good (mean 70.9, 95%CI 67.1, 74.6). Interviews identified several areas for improvement, including optimising its use for mobile devices. myfood24 appears to be acceptable and have potential to support self-management and behaviour change for women with GDM but requires adaptation to record blood glucose results alongside real-time tracking of diet.

Here, our data provide the first evidence for the existence of a previously unknown receptive system formed by novel DNA- and RNA-based receptors in eukaryotes. This system, named the TR-system, is capable of recognizing and generating a response to different environmental factors and has been shown to orchestrate major vital functions of fungi, mammalian cells, and plants.Recently, we discovered the existence of a similar regulatory system in prokaryotes. These DNA- and RNA-based receptors are localized outside of the membrane forming a type of a network around cells that respond to a variety of chemical, biological, and physical factors and enabled the TR-system to regulate major aspects of eukaryotic cell life as follows: growth, including reproduction and development of multicellular structures; sensitivity to temperature, geomagnetic field, UV, light, and hormones; interaction with viruses; gene expression, recognition and utilization of nutrients. The TR-system was also implicated in cell memory formation and was determined to be responsible for its maintenance and the forgetting of preceding events. This system is the most distant receptive and regulatory system of the cell that regulates interactions with the outer environment and governs the functions of other receptor-mediated signaling pathways.

The surface chemistry and the morphology of SnO2 nanowires, deposited by Vapour Phase Deposition (VPD) method on Au-covered silicon substrate, were studied before and after subsequent air exposure. For this purpose, surface-sensitive methods including X-ray Photoelectron Spectroscopy (XPS), Thermal Desorption Spectroscopy (TDS) and the Scanning Electron Microscopy (SEM) were applied. The studies presented within this paper allowed to determine the surface non-stoichiometry combined with the presence of carbon contaminations, in a good correlation with the surface morphology. The relative concentrations of the main components [O]/[Sn]; [C]/[Sn]; [Au]/[Sn] together with the O – Sn; O – Si bondings were analyzed. The results of TDS remained in a good agreement with the observations from XPS. Moreover, conclusions obtained for SnO2 nanostructures deposited with the use of Au catalyst were compared to the previous obtained for Ag-assisted tin dioxide nanowires. The information obtained within this studies are of great importance for the potential application of SnO2 nanowires deposited on Au covered Si substrate in the field of novel chemical nanosensor devices, since the results can provide an interpretation of how aging effects influence gas sensor dynamic characteristics.

Given the rise in the number of cases and their recurrences, Urinary Tract Infections (UTI) are one of the major burdens on public healthcare worldwide. Rapid, inexpensive and selective detection of Uropathogenic E. coli (UPEC), a major contributor to UTIs, is the need of the hour for effective treatment, given the rise of antibiotic-resistant bacteria due to improper diagnosis. Here we present a rapid, real-time, selective and label-free detection of UPEC using an integrated sensing platform based on Crossed Surface Relief Gratings (CSRGs) as nanoplasmonic sensors. Detection is achieved due to the unique Surface Plasmon Resonance (SPR)-based light energy exchange attributed to the CSRGs, allowing real-time sensing in a very narrow bandwidth of the incident light to pass where the SPR energy conversion occurs. The sensing ability of the platform is experimentally demonstrated by the detection of bulk Refractive Index (RI) changes, with a bulk sensitivity of 382.2 nm/RIU and a resolution in the order of 10-6 RIU. We demonstrate selective capture and detection of clinical concentration of UPEC, as opposed to other gram-negative bacteria, in real-time, a first for CSRGs. This work is particularly important for effective treatment of UTIs, allowing point-of-care diagnosis for economically disadvantaged regions around the world.

Blood has certain significant physical properties, which the authors investigated. This paper provides values of surface tension and viscosity of blood at 37 °C, as well as relationship between them plotted on a cross-plot. By applying Hagen- Poiseuille equation and Jurin's law to the experimentally obtained data, the authors calculated with great accuracy viscosity and surface tension of blood. Evaluating both of the properties using described methods required from the authors to know the density of investigated liquid, which was found to be on average $\rho=1063,56 \frac{kg}{m^3}$. The authors took blood samples from 30 healthy subjects and determined aforementioned physical properties. There has been made a distinction in regard of a sex of the blood donor. Results indicate that both surface tension and viscosity are independent from sex of a subject, as well as indicate that there is no correlation between viscosity and surface tension of blood at 37\degree C. Average values of surface tension and viscosity were found to be $\sigma=5,241\pm 0,262 \cdot 10^{-2}\frac{J}{m^2}$ and $\eta=3,352\pm0,360 \cdot 10^{-3} Pa \cdot s$, respectively.

Titanium membranes are used for guided bone regeneration in implant therapy. However, as a bioinert material, titanium does not have the ability to accelerate bone formation. Various titanium surface treatments to confer bioactivity have been demonstrated; however, there are concerns about the influence of chemical treatments on the corrosion of thin titanium membranes. This study investigated the influence of surface modifications on the structure of thin titanium membranes. Titanium membranes of 20 µm thickness were treated with acid or alkali solutions, and we evaluated their surface structure, wettability, corrosion depth, and mechanical strength compared to non-treated membranes. Alkali-treated thin titanium membranes displayed the formation of nanoscale pore structures on their surfaces, enhanced hydrophilicity, and less corrosion depth compared with acid-treated membranes. Furthermore, the tensile strength of alkali-treated membranes was comparable to non-treated membranes. These results suggest that alkali treatment is an appropriate surface modification method for thin titanium membranes.

Recently, a high internal surface of the titanium alloy pipe is required due to the increment of various applications of the pipe such as aerospace. However, the traditional machining process is unable to effectively polish the internal surface of the slender pipe. Thus, a vertical magnetorheological polishing (VMRP) apparatus is carried out in this work to implement high polishing performance on the internal surface of the titanium alloy pipe. The polishing process is realized by the combination of the rotating motion of the pipe and the reciprocating linear motion of the polishing head. Moreover, a series of comparative experiments are conducted to investigate the polishing mechanism of magnetorheological (MR) fluid and enhance the polishing performance. It is shown from the experimental results that proposed VMRP approach exhibits the better polishing performance than the conventional horizontal MR polishing method under same testing conditions. This is because the proposed VMRP method well eliminates the traces of polishing particles owing to the combination of polishing particles with different sizes. In addition, it is identified from the experimental test that the polishing time of the VMRP required to achieve the same polishing effect as the conventional method is shortened under the combination of different rotation speeds. It is identified from the above benefits of the VMRP that the final surface roughness after polishing is below 0.05 μm.

Under the extreme shortage of water resources in the Yellow River Basin, it is of great signifi-cance to analyze the spatial distribution relationship between rural settlement and water re-sources for the coordinated development of human and water resources in the Yellow River Ba-sin. However, the water allocation scheme depended on statistical data in the previous work, not on rural settlements in space. Furthermore, previous researches seldom focus on the evaluation of surface water resources accessibility according to the spatial distribution characteristics of ru-ral settlements and water resources, especially, in the Yellow River Basin and using rural set-tlement as unit. Therefore, a quantitative evaluation model of surface water resources accessibil-ity is constructed by using the GIS network analysis method, taking rural settlement as the re-search unit, based on three dimensions of topography, distance, and surface water resources, at the Yellow River basin scale. The results show that: (1) The surface runoff of rural settlement in the Yellow River basin is mostly less than 0.05 km/m2, reaching 99.83%. In other words, the Yel-low River Basin is extremely short of water resources. The surface water resources accessibility is affected by distance, topography, and surface water resources. The evaluation results show that the range of surface water resources accessibility is 0.13~0.88, with an average value of 0.47 and a standard deviation of 0.05. The High surface water resources accessibility value in the Yel-low River Basin is in the east and west, and the low value is mainly distributed in the middle. (2) The range from low to high of surface water resources accessibility in 12 catchments is Sanmen-xia station, Lanzhou station, Shizuishan station, Longmen station, Tongguan station, Toudaoguai station, Xiaolangdi station, Huayuankou station, Lijin station, Gaocun station, Ai Shan station and Tangnaihai station. (3) The value of surface water resources accessibility at the city scale is higher in the east of 10 cities and in the west of 1 city. However, it is lower in the west of 9 cities. And the values of the other cities are at a medium level. The correlation coefficient with primary industry GDP and surface water resources accessibility is 0.271 (N=56, Sig=0.043, in 0.05 level, the correlation is significant), which verifies the rationality of surface water resources accessibility model to some extent.

The effect of graphene (GR) on Ni surface relaxation and reconstruction in three different substrate orientations: {111}, {001}, {011}, at two different temperatures: 300K and 400K was studied using Molecular Dynamics simulation. The change of the interplanar distances of the substrate and redistribution of Ni and C atoms in direction perpendicular to the surface were compared with the equilibrium state of GR and bulk Ni, in the absence of the counterpart. The surface reconstruction for GR/Ni system was analyzed base on the calculated radial pair distribution function of Ni and C atoms. The surface roughness was visualized using 2D atomic distribution maps. For the studied substrate orientations and temperatures, it was found that the most densely packed orientation of the Ni base {111} provides minimal changes of the structural parameters of both counterparts at 400 K.

Anion exchange of the halides, Br and I, is demonstrated through the direct mixing of two pure perovskite quantum dot solutions, CsPbBr3 and CsPbI3, and is shown to be both facile and result in a completely alloyed single phase mixed halide perovskite. Anion exchange is also observed in an interlayer printing method utilizing the pure, unalloyed perovskite solutions and a commercial inkjet printer. The halide exchange was confirmed by optical absorption spectroscopy, photoluminescent spectroscopy, X-ray diffraction, and X-ray photoemission spectroscopy characterization, and indicates that alloying is thermodynamically favorable, while the formation of a clustered alloy is not favored. Additionally, a surface-to-bulk photoemission core level transition is observed for the Cs 4d photoemission feature which indicates the electronic structure of the surface is different from the bulk. Time resolved photoluminescence spectroscopy indicates the presence of multiple excitonic decay features which is argued to originate from states residing at surface and bulk environments.

The catenary shells of revolution are widely used in constructions due to their unique mechanics' feature. However, no publications on this type of shells can be found in the literature. To have a better understanding of the deformation and stress of the catenary shells of revolution, we formulate the principal radii for two kinds of catenary shells of revolution and their displacement type governing equations. Numerical simulations are carried out based on both Reissner-Meissner mixed formulations and displacement formulations. Our investigations show that both deformation and stress response of elastic catenary shells of revolution are sensitive to its geometric parameter $c$, and reveal that the mechanics of the catenary shells of revolution does much better than the spherical shells. Two complete codes in Maple are provided.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

Rice blast and brown planthopper (BPH) are two of the most destructive diseases and pests in rice (Oryza sativa L.) production in China. The development of multi-resistant varieties is widely recognized as the most efficient and environmentally friendly approach to controlling crop diseases and pests. Functional molecular markers (FMMs) have been developed from functional variants in the genic region associated with trait variation, greatly enhancing the efficiency of identifying and pyramiding valuable genes in crop breeding. In this study, two FMMs and a multiplex PCR amplification system were developed for two major broad-spectrum BPH resistance genes, Bph6 and Bph9. By assistance of FMMs in multi-resistant rice restorer line development pipeline, two lines (Huahui7713 and Huahui3006) with blast and BPH resistance were developed by pyramiding three resistance genes Pigm, Bph6 and Bph9. Huahui7713 and Huahui3006 as male lines, two new hybrid rice varieties (WeiLiangYou7713 and Xuanliangyou3006) were certificated and commercial released in China. WeiLiangYou7713 and Xuanliangyou3006 showed improved blast and BPH resistance, and no penalty on yield and grain-quality. Annual promotion area of WeiLiangYou7713 has exceeded 53.3 thousand hectares, indicating its widespread adoption and success in the market. Huahui7713 and Huahui3006 could have great potential for utilization in blast and BPH resistance rice breeding.

Amid the deepening imbalance in the supply and demand of allogeneic organs, xenotransplanta-tion can be a practical alternative because it makes an unlimited supply of organs possible. How-ever, to perform xenotransplantation on patients, the source animals to be used must be free from infectious agents. This requires breeding of animals using assisted reproductive techniques, such as somatic cell nuclear transfer, embryo transfer, and cesarean-section, without colostrum de-rived in designated pathogen-free (DPF) facilities. Most infectious agents can be removed from animals produced by these methods, but several viruses known to pass through the placenta are not easy to remove, even with these methods. Therefore, in this review, we look at the characteris-tics of several viruses known to cross the placenta and determine how they can be detected. This review is intended to help maintain DPF facilities by preventing animals infected with the virus from entering DPF facilities and to help select pigs suitable for xenotransplantation.

The retrospective noninterventional study investigated the kinetic energy of video images of 18 fertilized eggs (7 were normal and 11 were abnormal) recorded by a time-lapse device leading up to the beginning of the first cleavage. The norm values of cytoplasmic particles were measured by the optical flow method. Three phases profile for normal cases were found regarding the kinetic energy that were 2.199×10⁻²⁴±2.076×10⁻²⁴, 2.369×10⁻²⁴±1.255×10⁻²⁴, and 1.078×10⁻²⁴±4.720×10⁻²⁵ (J) for the phases 1, 2, and 3, respectively. In phase 2, the energies were 2.369 × 10⁻²⁴ ± 1.255 × 10⁻²⁴ and 4.694 × 10⁻²⁴ ± 2.996 × 10⁻²⁴ (J) (mean ± SD, P = 0.0372), and the time required was 8.114 ± 2.937 and 6.018 ± 5.685 (H) (P = 0.0413) for the normal and abnormal cases, respectively. The kinetic energy change was considered a condition for applying the free energy principle that states that, for any self-organized system to be in equilibrium in its environment, it must minimize its informational free energy. The kinetic energy while interpreting it in terms of the free energy principle suggesting clinical usefulness would further our understanding of the phenomenon of fertilized egg development with respect to the birth of human life.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

Drones have been used in a variety of scenarios such as atmospheric monitoring, fire rescue, agricultural irrigation, etc., in which accurate environmental perception is of crucial importance for both decision-making and control. Among the drone sensors, the RGB camera is indispensable for capturing rich visual information for vehicle navigation but encounters a grand challenge in high-dynamic-range scenes that occur frequently in real applications. Specifically, the recorded frames suffer from under-exposure and over-exposure simultaneously and degenerate the successive vision tasks. To solve the problem, we take object tracking as an example and leverage the superior response of event cameras over a large intensity range to propose an event-assisted object tracking algorithm that can achieve reliable tracking under large intensity variations. Specifically, we propose to pursue feature matching from dense event signals, and based on which to (i) design a UNet-based image enhancement algorithm to balance the RGB intensity with the help of neighboring frames in the time domain, and then (ii) construct a dual-input tracking model to track the moving objects from intensity balanced RGB video and event sequence. The proposed approach is comprehensively validated in both simulation and real experiments.

This study examined the impact of Vibration-Assisted Drilling (VAD) on hole quality and residual stress in Ti-6Al-4V ELI material. Ti-6Al-4V ELI possesses excellent mechanical properties but presents challenges in machining, including chip evacuation, burr formation, and elevated cutting temperatures. VAD, particularly Low-Frequency Vibration-Assisted Drilling (LF-VAD), has been explored as a potential solution to address these issues. The research com-pares LF-VAD with conventional drilling (CD) under various cutting and cooling conditions. LF-VAD exhibits higher maximum cutting forces under specific conditions, which result in accel-erated tool wear. However, it also demonstrates lower RMS (Root Mean Square) forces com-pared to CD, offering better control over chip formation, reduced burr formation, and improved surface roughness within the hole. Furthermore, LF-VAD generates greater compressive residual stresses on the hole's inner surface compared to CD, suggesting enhanced fatigue performance. These findings indicate that LF-VAD holds promise for improving hole quality, fatigue life, and overall component durability in Ti-6Al-4V machining applications.

In this paper we overview all analytical engineering solutions for corrosion problems in pressure vessels delivered over the past 60 years. We briefly detail strengths and weaknesses of existing approaches, thus demonstrating the need for novel uniform corrosion analysis methods for both current and new applications. To complement the review, we also present a new analytical model allowing to estimate the lifetime of pressured elastic vessels with mechanically assisted corrosion. Both internal/external pressure and internal/external corrosion are captured and dissolution driven corrosion is also considered. The readily implemented method improves existing analytical approaches and is shown to be effective for thin and thick shells, as well as various loading and corrosion intensity and geometrical conditions.

Purpose The COVID-19 pandemic, triggered by the novel severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), has resulted in over 160 million infections and 3.5 million fatalities worldwide. Evidence of SARS-CoV-2 presence in the highly vascularized penile tissue and the established correlation between COVID-19 and subsequent erectile dysfunction (ED) has emerged. Robot-assisted radical prostatectomy (RARP) is a popular procedure for prostate cancer because of its reliability and swift recovery rate. However, the ED prevalence post-surgery is believed to be comparable to open surgery, and postoperative ED significantly affects the patient's quality of life. Our study aimed to explore the effect of COVID-19 on ED recovery in patients undergoing bilateral nerve preservation during RARP. Materials and Methods We conducted a retrospective study on 85 patients who underwent bilateral nerve-sparing RARP (nsRARP) at our institution between December 2017 and May 2021. Chart reviews and the International Index of Erectile Function-5 (IIEF-5) questionnaire facilitated the analysis. Our objective was to contrast ED recovery after surgery between SARS-CoV-2–infected and non-infected patients using preoperative IIEF-5 scores and scores at 6, 12, and 24 months post-surgery. We defined successful ED recovery as an IIEF-5 score of 17 or higher and successful sexual intercourse. We also compared ED recovery rates between the two groups, regardless of the timing of COVID-19 diagnosis. IBM's SPSS version 18.0 assisted in the statistical analysis, with Fisher's exact test and chi-square test used for comparing categorical variables. Independent t-tests determined mean differences between baseline and postoperative IIEF-5 scores. A p-value less than 0.05 was considered statistically significant. Results From December 2017 to May 2021, our institution executed 213 RARP cases, with 185 of these involving nerve preservation. Among these patients, 133 had an IIEF-5 score of 17 or higher during preoperative EF assessment. We included 85 patients with consistent IIEF-5 records before surgery and at 6, 12, and 24 months post-surgery in this study. Of these, 44 and 41 patients comprised the COVID-19–positive and COVID-19–negative groups, respectively. The COVID-19–positive group had a higher proportion of diabetes mellitus (DM) patients (24 (54.55%) vs. 7 (17.07%), p<0.001). There was no significant difference in preoperative IIEF-5 scores or scores up to 6 months after surgery between the two groups. However, the IIEF-5 scores of the COVID-19–positive group were statistically lower after 12 and 24 months post-surgery. Additionally, the COVID-19–negative group showed a more considerable score increase between 6 and 12 months post-surgery, and the EF recovery rate was lower in the COVID-19–positive group starting from the 12th month after surgery. Within the COVID-19–positive group, no statistically significant difference in IIEF-5 scores was found between single infection and multiple reinfection groups. Conclusions Principal component analysis revealed the impact of COVID-19 on ED recovery in patients who underwent nsRARP. The most substantial changes in IIEF-5 scores occurred between 6 and 12 months. From 12 months onwards, the COVID-19–positive group had significantly lower scores, and fewer patients had IIEF-5 scores above 17. However, the number of COVID-19 diagnoses did not significantly affect the IIEF-5 scores.

Ovarian tissue cryopreservation (OTC) or testicular tissue cryopreservation (TTC) are effective and often the only options for fertility preservation in female or male patients due to oncological, medical, or social aspects. While TTC and resumption of spermatogenesis, either in vivo or in vitro, has still be considered an experimental approach in humans, OTC and autotransplantation has been applied increasingly to preserve fertility with more than 200 live births worldwide. However, the cryopreservation of reproductive cells followed by the resumption of gametogenesis, either in vivo or in vitro, may interfere with sensitive and highly regulated cellular processes. In particular, the epigenetic profile, which includes not just reversible modifications of the DNA itself but also post-translational histone modifications, small non-coding RNAs, gene expression and availability, and storage of related proteins or transcripts, have to be considered in this context. Due to complex reprogramming and maintenance mechanisms of the epigenome in germ cells, growing embryos, and offspring, OTC and TTC are carried out at very critical moments early in the life cycle. Given this background, the safety of OTC and TTC taking into account the epigenetic profile has to be clarified. Cryopreservation of mature germ cells (including Metaphase II oocytes and mature spermatozoa collected via ejaculation or more invasively after testicular biopsy) or embryos has been used successfully for many years in Medically Assisted Reproduction (MAR). However, tissue freezing followed by in vitro or in vivo gametogenesis has become more attractive in the past, while few human studies have analysed the epigenetic effects, with most data deriving from animal studies. In this review, we highlight the potential influence of the cryopreservation of immature germ cells and subsequent in vivo or in vitro growth and differentiation on the epigenetic profile in humans and animals.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

In the recent years, Cannabis and hemp-based products have become increasingly popular for various applications ranging from recreational use, edibles, beverages to health care products and medicines. The rapid detection and differentiation of phytocannabinoids is, therefore, essential to assess the potency, therapeutic and nutritional values of cannabis cultivars. Here, we implemented the SpiderMass technology for the in vivo detection of cannabidiol acid (CBDA) and tetrahydrocannabinol acid (THCA) and other endogenous organic plant compounds to access distribution gradients within the plants and differentiate cultivars. The SpiderMass system is composed of an IR- laser handheld microsampling probe connected to the mass spectrometer through a transfer tube. The analysis was performed in situ on different plant organs from freshly cultivated Cannabis plants in only a few seconds. SpiderMass analysis easily discriminated the two acid phytocannabinoid isomers by MS/MS and the built statistical models differentiated between four Cannabis cultivars. Different abundancies of acid phytocannabinoids were also found along the plant as well as between different cultivars. All together, these results introduce the direct analysis by SpiderMass as a compelling analytical alternative for forensic and hemp industrial analysis.

We attempted to establish an objective method to accurately evaluate the motility of bull sperm and examined the effects of media for sperm suspensions and frame rates on data of computer-assisted sperm motility analysis (CASA). Sperm incubated in Brackett and Oliphant medium (BO) more clearly showed hyperactivation-like motility than those in synthetic oviductal fluid. Sperm images captured at 150 frames per second (fps) showed a trajectory that was closer to the real pathway than those at other frame rates (30, 50, and 75 fps). We then examined the characteristics of sex-sorted and non-sorted semen using a cluster analysis followed by a discriminant analysis of sperm motility in BO at 150 fps. The results indicated that sex-sorted semen contained sperm with hyperactivation-like motility as the main subpopulation immediately after thawing and this subpopulation decreased after 2-h incubation. The main subpopulation in non-sorted semen had progressive motility that was maintained during incubation. In conclusion, usage of BO for sperm suspensions and capturing sperm motility at 150 fps by CASA were appropriate for evaluating bovine sperm motility. A discriminant analysis using data from a cluster analysis of motile sperm has the ability to accurately describe differences in the structures of sperm motility subpopulations.

Background Natural Saccharomyces cerevisiae yeast strains exhibit very large genotypic and phe-notypic diversity. Breeding programs taking advantage of this characteristic, are widely used for yeast selection in the wine industry, especially in the recent years when winemakers need to adapt their production to climate change. The aim of this work was to evaluate a Marker Assisted Se-lection (MAS) program to improve malic acid consumption capacity of Saccharomyces cerevisiae in grape juice. Methods Optimal individuals of two unrelated F1-hybrids were crossed to get a new genetic background carrying many “malic consumer” loci. Then, eleven QTLs already identified were used for implementing the MAS breeding program. Results By this way, extreme individuals able to consume more than 70% of malic acid in grape juice were selected. These individuals were tested in different enological matrixes and compared to their original parental strains. They greatly reduced the malic acid content at the end of alcoholic fermentations, they appeared to be robust to the environment and accelerate the ongoing of malo-lactic fermentations by Oenococcus oeni. Conclusions This study illustrates how MAS can be efficiently used for selecting industrial Saccharomyces cerevisiae strains with outlier properties for winemaking.

We demonstrate hybrid integration of a lithium niobate microring resonator with a silicon nitride waveguide in the vertical configuration to achieve efficient light coupling. The microring resonator is fabricated on a lithium niobate on insulator (LNOI) substrate using photolithography assisted chemo-mechanical etching (PLACE). A fused silica cladding layer is deposited on the LNOI ring resonator. The silicon nitride waveguide is further produced on the fused silica cladding layer by first fabricating a trench in the fused silica using focused ion beam (FIB) etching for facilitating the evanescent coupling, followed by formation of the silicon nitride waveguide on the bottom of the trench. The FIB etching ensures the required high positioning accuracy between the waveguide and the ring resonator. We achieve Q-factors as high as 1.4*10^7 with the vertically integrated device.

Background and Objectives: Acute compartment syndrome (ACS) is an emergency condition of the lower limb in which prophylactic fasciotomy is required to prevent complications. A negative pressure wound therapy (NPWT) used to the treatment of fasciotomy wounds provide beneficial clinical results. This study aimed to exchange the authors’ experience of using the NPWT installation system on the lower limb wounds after fasciotomy in ACS. Materials and Methods: This is a retrospective study enrolled consecutive patients with ACS, who underwent fasciotomy and was treated with the NPWT installation system at Department of Vascular Surgery, Provincial Hospital in Kielce from April 2016 to July 2017. Results: The study enrolled 15 patients with a diagnosis of ACS (87% men, mean age 65 years old). An open four-compartment fasciotomy (87%) or two-compartment fasciotomy (13%) was performed. The NPWT was applied on the first day after fasciotomy in 87% of patients. Therapy was initiated by the negative pressure of 125 mm Hg, which maintained at this level until the therapy was finalized. In 80% of patients, the vacuum-assisted wound closure (VAC) dressing changes were performed every 3 days. The first approximation of fasciotomy wounds margins occurred on the 4th day after surgery among 67% of individuals. The average time of using VAC on fasciotomy wounds was 9 days. The average time to definitive closure edges of fasciotomy wounds was 12 days. The average time of hospital stay was 17 days. Conclusions: Our experience indicates the legitimacy of using NPWT in wound treatment after fasciotomy in ACS. The NPWT enables faster primary closure of wounds, reduces edema, as well as decreases hospitalization time.

In this research, low-fat dried Chinese sausage was formulated with mango peel pectin (MPP) extracted by microwave assisted extraction (MAE) (0%, 5%, 10% and 15% (w/w). The extractable yield of pectin attained from peel of Nam Dok Mai variety was achieved at 13.85% using 700-watt power. The extracted MPP were of high equivalent weight (1,485.78 mg/mol), degree esterification (77.19%) and methoxyl content (19.33%) with the structure of more porosity as compared to that of the conventional method. Spectrum scans by Fourier transform infrared spectrophotometer (FT-IR) advised that the extracted MPP gave the similar wave number profiles as the commercial pectin. Quality attributes of the Chinese sausages were accessed and compared with the control formula (CTRL). At higher concentrations of MPP, the product had positively increased colour intensity. The texture profile of the sausage illustrated that only the hardness value was comparable with the CTRL, while springiness, cohesiveness, gumminess and chewiness were statistically lower (p < 0.05). Furthermore, the sensory evaluation by experienced panellists (n=12) indicated that 5% MPP similarly represented overall acceptability with the CTRL. Consequently, MPP can be effectively applied at low level as fat replacement in Chinese sausage allowing colour improvement and product of healthier option.

In order to integrate genomics in breeding and development of drought tolerant groundnut genotypes, identification of genomic regions/genetic markers for drought surrogate traits is essential. We used SNP markers for a genetic analysis of the ICRISAT groundnut minicore collection for genome wide marker-trait association for some physiological traits and to determine the magnitude of linkage disequilibrium (LD) present in the genetic resources. The LD analysis showed that about 36% of loci pairs were in significant LD (P < 0.05 and r2 > 0.2) and 3.14% of the pairs were in complete LD. There was rapid decline in LD with distance and the LD was <0.2 at a distance of 41635 bp. The marker trait association (MTAs) studies revealed 20 significant MTAs (p <0.001) with 11 markers for leaf area index (4), canopy temperature (13), chlorophyll content (1) and NDVI (2). The markers explained 2 to 21% of the phenotypic variation observed. Most of the MTAs identified on the A subgenome were also identified on the respective homeologous chromosome on the B subgenome. The duplications of effect observed could be due to common ancestor of the A and B genome which explains the linkage detected between markers lying on different chromosomes seen in the current study. The present study identified a total of 20 highly significant marker trait associations with 11 markers for four physiological traits of importance in groundnut; LAI, CT, SCMR and NDVI. The markers identified in this study can serve as useful genomic resources to initiate marker-assisted selection and trait introgression of groundnut for drought tolerance. The identified markers in this study may be useful for marker assisted selection after further validation.

Due to the increasing importance of mangroves in climate change mitigation projects, more accurate and cost-effective aboveground biomass (AGB) monitoring methods are required. However, field measurement of AGB may be a challenge because of its remote location and the difficulty to walk in these areas. This study is based on the Livelihoods Fund’ Oceanium project of 10,000 hectare mangrove plantations monitoring. In a first step, the possibility of replacing traditional field measurements of sample plots in a young mangrove plantation by a semiautomatic processing of UAV-based photogrammetric point clouds was assessed. In a second step, Sentinel-1 radar and Sentinel-2 optical imagery were used as auxiliary information to estimate AGB and its variance for the entire study area under a model-assisted framework. AGB was measured using UAV imagery in a total of 95 sample plots. UAV plot data was used in combination with non-parametric Support Vector Regression (SVR) models for the estimation of the study area AGB using model-assisted estimators. Purely UAV-based AGB estimates and their associated standard error (SE) were compared with model-assisted estimates using (1) Sentinel-1, (2) Sentinel-2 and (3) a combination of Sentinel-1 and Sentinel-2 data as auxiliary information. The validation of the UAV-based individual tree height and crown diameter measurements showed a root mean square error (RMSE) of 0.21 m and 0.32 m respectively. Relative efficiency of the three model-assisted scenarios ranged between 1.61 and 2.15. Although all SVR models improved the efficiency of the monitoring over UAV-based estimates, the best results were achieved when a combination of Sentinel-1 and Sentinel-2 data was used. Results indicated that the methodology used in this research can provide accurate and cost-effective estimates of AGB in mangrove young plantations.

High Brassicaceae consumption reduces the risk of developing several cancer types, probably due to their glucosinolate amount. Extracts from Sinapis nigra L. and Sinapis alba L. have been obtained from leaves and seeds under different conditions using ethanol/water mixtures because well accepted by food industry. The EtOH/H2O 8:2 mixture gives better yields in glucosinolate amounts from grinded seeds, mainly sinalbin in S. alba and sinigrin in S. nigra. The highest antiproliferative activity in both non-tumour and tumour cell lines was induced by S. alba seeds extract. To evaluate whether Sinapis spp effect was only due to glucosinolate content or it was influenced by the extracts’ complexity, cells were treated with extracts or glucosinolates, in the presence of myrosinase. Pure sinigrin did not modify cell proliferation, while pure sinalbin was less effective than the extract. The addition of myrosinase increased the antiproliferative effects of the S. nigra extract and sinigrin. Antiproliferative activity was correlated to MAPKs modulation, which was cell and extract-dependent. Cell-cycle analysis evidenced a proapoptotic effect of S. alba on both tumour cell lines and of S. nigra only on HCT 116. Both extracts showed good antimicrobial activity in disc diffusion tests and on ready-to-eat fresh salad. These results underline the potential effects of Sinapis spp in chemoprevention and food preservation.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

Traditional ways of validating satellite-derived sea surface temperature (SST) and sea surface salinity (SSS) products, using comparisons with buoy measurements, do not allow for evaluating the impact of mesoscale to submesoscale variability. Here we present the validation of remotely-sensed SST and SSS data against the unmanned surface vehicle (USV) – Saildrone – measurements from the Spring 2018 Baja deployment. More specifically, biases and root mean square differences (RMSD) were calculated between USV-derived SST and SSS values, and six satellite-derived SST (MUR, OSTIA, CMC, K10, REMSS, and DMI) and three SSS (JPLSMAP, RSS40, RSS70) products. Biases between the USV SST and OSTIA/CMC/DMI were approximately zero while MUR showed a bias of 0.2C. OSTIA showed the smallest RMSD of 0.36C while DMI had the largest RMSD of 0.5C. An RMSD of 0.4C between Saildrone SST and the satellite-derived products could be explained by the daily variability in USV SST which currently cannot be resolved by remote sensing measurements. For SSS, values from the JPLSMAP product showed saltier biases of 0.2 PSU, while RSS40 and RSS70 showed fresh biases of 0.3 PSU. An RMSD of 0.4 PSU could not be explained solely by the daily variability of the USV-derived SSS. Coherences were significant at the longer wavelengths, with a local maximum at 100 km that is most likely associated with the mesoscale turbulence in the California Current System.

This study aims to assess the potential of the LDAS-Monde a land data assimilation system developed by Météo-France to monitor the impact of the 2018 summer heatwave over western Europe vegetation state. The LDAS-Monde is forced by the ECMWF’s (i) ERA5 reanalysis, and (ii) the Integrated Forecasting System High Resolution operational analysis (IFS-HRES), used in conjunction with the assimilation of Copernicus Global Land Service (CGLS) satellite derived products, namely the Surface Soil Moisture (SSM) and the Leaf Area Index (LAI). Analysis of long time series of satellite derived CGLS LAI (2000-2018) and SSM (2008-2018) highlights marked negative anomalies for July 2018 affecting large areas of North Western Europe and reflects the impact of the heatwave. Such large anomalies spreading over a large part of the considered domain have never been observed in the LAI product over this 18-yr period. The LDAS-Monde land surface reanalyses were produced at spatial resolutions of 0.25°x0.25° (January 2008 to October 2018) and 0.10°x0.10° (April 2016 to December 2018). Both configuration of the LDAS-Monde forced by either ERA5 or HRES capture well the vegetation state in general and for this specific event, with HRES configuration exhibiting better monitoring skills than ERA5 configuration. The consistency of ERA5 and IFS HRES driven simulations over the common period (April 2016 to October 2018) allowed to disentangle and appreciate the origin of improvements observed between the ERA5 and HRES. Another experiment, down-scaling ERA5 to HRES spatial resolutions, was performed. Results suggest that land surface spatial resolution is key (e.g. associated to a better representation of the land cover, topography) and using HRES forcing still enhance the skill. While there are advantages in using HRES, there is added value in down-scaling ERA5, which can provide consistent, long term, high resolution land reanalysis. If the improvement from LDAS-Monde analysis on control variables (soil moisture from layers 2 to 8 of the model representing the first meter of soil and LAI) from the assimilation of SSM and LAI was expected, other model variables benefit from the assimilation through biophysical processes and feedbacks in the model. Finally, we also found added value of initializing 8-day land surface HRES driven forecasts from LDAS-Monde analysis when compared with model only initial conditions.

In urban area, one of the great problem is the rise of temperature, which leads to form the urban heat island effect. This paper refers to the trend of the urban surface temperature extracted from the Landsat images from which to consider changes in the formation of surface urban heat island for the north of Ho Chi Minh city in period 1995-2015. Research has identified land surface temperature from thermal infrared band, according to the ability of the surface emission based on characteristics of normalized difference vegetation index NDVI. The results showed that temperature fluctuated over the city with a growing trend and the gradual expansion of the area of the high-temperature zone towards the suburbs. Within 20 years, the trend of the formation of surface urban heat island with two typical locations showed a clear difference between the surface temperature of urban areas and rural areas with space expansion of heat island in 4 times in 2015 compared to 1995. An extreme heat island located in the inner city has an area of approximately 18% compared to the total area of the region. Since then, the solution to reduce the impact of urban heat island has been proposed, in order to protect the urban environment and the lives of residents in Ho Chi Minh City becoming better

This manuscript reviews two decades of projects funded by the Kirkhouse Trust (KT), a charity registered in the UK. KT was established to improve the productivity of legume crops important in African countries and in India. KT’s requirements for support are: 1) the research must be done by national scientists in their home institution, either a publicly funded agricultural research institute or a university; 2) the projects need to include a molecular biology component, which to date has mostly comprised the use of molecular markers for the selection of one or more target traits in a crop improvement programme; 3) the projects funded are included in consortia, to foster the creation of scientific communities and the sharing of knowledge and breeding resources. This account relates to the key achievements and challenges, reflects on the lessons learned and outlines future research priorities.

"Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trainsFollowing the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

Wild strawberry (Fragaria vesca L.) leaves possess diverse antioxidant properties, mainly due to the different classes of phenolics. In this study, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) of wild strawberry phenolics were carried out to understand the impact of extraction temperature, extraction time and solvent-to-sample ratio (SSR) on the quantitative and qualitative properties of the obtained extracts. The highest total phenolic content (8027 mg GA/100 g DW), as well the highest DPPH• antiradical activity (903 mol TE/g DW) was obtained with ASE at 150 °C, static time 5 min and SSR of 40:1; while the highest ABTS•+ antiradical activity (681 mol TE/g DW,) and FRAP (2389 mol TE/g DW) was obtained with MAE after 5 min at 80 °C and a SSR of 40:1. The correlation analysis showed that phenolics largely contributed to the antioxidant properties of the studied MAE extracts, while correlation was not found in ASE extracts. A total of 54 different phenolics were identified by UPLC/MS-MS in MAE and ASE extracts obtained at optimal extraction conditions. MAE extract was shown to have a higher content of phenolic acids (40%), but lower content of proanthocyanidins (88%), flavonols (29%), flavan-3-ols (50%) and flavones (39%) than ASE extract.

Recent digital transformations have significantly impacted the current society, economy, and culture. This includes adoption of rapidly emerging technologies, such as artificial intelligence (AI), immersive technology (e.g., virtual, augmented, mixed and extended reality (VR/AR/MR/XR)), cloud services, and internet of things, in our day-to-day life. `Metaverse’ has emerged as a technology that incorporates many of these transforming technologies to deliver personalised immersive experience related to specific application areas. A potential major beneficiary of Metaverse is the educational ecosystem, where highly immersive learning experiences can be delivered to students, catering to their personal learning needs and train them on life skills such as empathy, ethical qualities, and communication skills. The present-day Metaverse allows physical engagement, enabling users to utilise limb movements to interact with the presented materials. However, ethical concerns and technical limitations impede the widespread implementation of the Metaverse in the real-world. This paper provides a comprehensive survey of the existing literature covering the architecture, type and components of Metaverse, followed by practical aspects of metaverse implementation. The paper is concluded by discussing on the open challenges and issues along with their mitigation strategies and future research directions after the detailed usecase of Metaverse in Education.

Obesity represents a worldwide epidemic disorder, increasing the overall morbidity and mortality rate. In this study we investigated the impact of obesity on peri-operative and long-term functional outcomes of Robotic assisted simple prostatectomy (RASP). Baseline flowmetry parameters and validated questionnaires’ scores were prospectively recorded. Follow-up assessments included Flowmetry and validated questionnaires. Composite outcomes (Trifecta) was defined as combination of: post-operative Q-max>15 ml/sec, IPSS score<8 and absence of complications. Pentafecta included also post-operative ejaculation persistence (MSHQ score>0) and the Erectile function maintenance (∆IEEF<6). Data were stratified by BMI (<30 or ≥30). 81 patients underwent RASP in our Institution. Baseline demographics and clinical features, questionnaires score and baseline flowmetry results were comparable between obese and non-obese cohorts. At follow-up, obese patients reported lower subjective improvement in IPSS (p=0.02) and OABQ scores (p<0.001) and higher incidence of stress incontinence requiring Duloxetin (p<0.001). Flowmetry outcomes, were also worse in this cohort (p=0.02 and p=0.03, respectively). At comprehensive outcomes assessment, obese patients had comparable Trifecta (67% vs 54%, p=0.39) and pentafecta achievement rate (p=0.76). Our prelimirary results proved that obesity is associated with worse functional outcomes (storage LUTS and incontinence rate) after RASP, but doesn’t affect trifecta and pentafecta achievement rate.

Reductive amination is a powerful tool in sustainable organic synthesis that allows chemists to access a wide range of valuable amine products using renewable feedstocks, mild reaction con-ditions, and with minimal waste generation. Practical applications can be found in various fields, including pharmaceuticals, contributing to greener and more sustainable chemical processes. In this work we present a heterogeneous (Rh and Pt) catalysed protocol for the fast and efficient synthesis of ractopamine hydrochloride (-adrenergic drug) under MW-assisted reductive ami-nation protocol starting from raspberry ketone and octapamine. Microwave (MW) successfully accelerated the hydrogenation reaction and reduced the reaction time from 13 hours to only 3 hours under mild conditions (50°C at 10 bar). The best catalysts were Pt/C and Rh/C, which led to high conversion and selectivity towards ractopamine:HCl. The solvent has a significant effect on the reaction outcome. The replacement of methanol with other solvents had a negative impact on the reaction yield. We also replaced the raspberry ketone with other ketone substrates, especially cyclohexanone. These preliminary experiments may be useful for further process improvements in the synthesis of β-adrenergic agonists and related structures.

The global prevalence of insulin resistance (IR) is increasing continuously, influencing metabolic parameters and fertility as well. The metabolic changes due to IR can alter the molecular composition of plasma and other body fluids. Follicular fluid (FF) is derived mainly from plasma, and it is a critical microenvironment for the developing oocytes. It contains various metabolites and amino acids, and the quality of the oocytes is linked at least partially to amino acid metabolism. Our goal was to determine quantitatively the amino acid (AA) profile of FF in IVF patients and to compare IR and non-insulin resistance (NIR) groups to investigate the AA changes in their FF. By UHPLC-based method we quantified the main 20 amino acids from human FF samples in the IR and NIR groups. Several amino acids (aspartate, glycine, glutamate, and cysteine) differed significantly (p&lt;0.05 or less) between the two groups. The most significant alterations between the IR and NIR groups were related to the glutathione metabolic pathway involving glycine, serine, and threonine. Since insulin resistance alters the amino acid composition of the FF, the oocytes may undergo metabolism-induced changes resulting in poor oocyte quality and less fertility in the insulin resistance groups.

Equine-assisted services (EAS) are being increasingly used as complementary interventions for military veterans who have experienced trauma. However, there is limited evidence of benefit for this population and almost no literature describing desired potential outcomes and possible mechanisms of action. The aim of this article is to address these gaps by reviewing the extant literature of animal-assisted interventions in general, and equine-assisted services in particular, with the goal of providing guidance for future investigations in the field. Currently, the field is in the early stage of scientific development, but published results are promising. Interventions that enhance treatment compliance and/or outcomes could benefit this population. Preliminary results, reviewed herein, indicate that EAS interventions might benefit the military veteran population by enhancing treatment engagement and therapeutic alliance, as well as contributing to symptom reduction and resulting in various transdiagnostic benefits. It is recommended that future studies include exploration of potential beneficial outcomes discussed herein as well as investigate suggested mechanisms of action.

Equine Assisted Activities (EAA) are considered a suitable innovative rehabilitative practice for children with neurodevelopmental disorders, including Autism Spectrum Disorder (ASD). While standardized scales have been previously used as a tool to evaluate the effects of EAA on different domains of functioning in ASD children, few studies have considered an ethological approach as a means to describe human-horse interactions in the context of ASD. In this study, we aimed to evaluate the behaviour of 19 children with ASD - in comparison with 19 typically developing children (TD) - during EAA sessions. We developed an ethogram from the video-recordings, to assess spatial relationships, social interactions and communicative behaviours displayed by the child towards the horse, as well as the occurrence of problem behaviours. Results indicate that children’s behaviours during EAA sessions are modulated by sex and age, while previous children’s experience with EAA appeared to improve interpersonal distance and horse handling. Results from this study highlight the importance of exploring children's behavioural response during animal-assisted activities through direct measurements. This may allow linking the quality/strength of the child-horse relationship to the benefits obtained by the child, particularly in the social/communicative domain, a core symptom of ASD.

The upper extremities limitation represents one of the essential functional impairments in patients with cervical spinal cord injury. Electromechanics assisted devices and robots are increasingly used in neurorehabilitation to help functional improvement in patients with neurological diseases. This review aimed to systematically report the evidence-based, state-of-art on clinical applications and robotic-assisted arm training (RAT) in motor and functional recovery in subjects affected by cervical spinal cord injury. The present study has been carried out within the framework of the Italian Consensus Conference on "Rehabilitation assisted by robotic and electromechanical devices for persons with disability of neurological origin" (CICERONE). PubMed/MEDLINE, Cochrane Library, and Physiotherapy Evidence Database (PEDro) databases were systematically searched from inception to September 2021. The 10-item PEDro scale assessed the study quality for the RCT and the AMSTAR-2 for the systematic review. Two different authors rated the studies included in this review. If consensus was not achieved after discussion, a third reviewer was interrogated. The 5-item Oxford CEBM scale was used to rate the level of evidence. A total of 11 studies were included. The selected studies were: two systematic reviews, two RCTs, one parallel-group controlled trial, one longitudinal intervention study and five case series. One RCT was scored as a high-quality study, while the systematic review was of low quality. RAT was reported as feasible and safe. Initial positive effects of RAT were found for arm function and quality of movement in addition to conventional therapy. The high clinical heterogeneity of treatment programs and the variety of robot devices could severely affect the generalizability of the study results; therefore, future studies are warranted to standardize the type of intervention and evaluate the role of robotic-assisted training in subjects affected by cervical spinal cord injury.

Access to broadband communications in different parts of the world has become a priority for some governments and regulatory authorities around the world in recent years. Building new digital roads and pursuing a connected society includes looking for easier access to the Internet. In general, not all the areas where people congregate are fully covered, especially in rural zones, thus restricting access to data communications and bringing inequality. In the present review article, we have comprehensively surveyed the use of three platforms to deliver broadband services to such remote and low-income areas are proposed: Unmanned Aerial Vehicles (UAV), Altitude Platforms (APS), and Low-Earth Orbit (LEO) satellites. These novel strategies support the connected and accessible world hypothesis. Hence UAVs are considered a noteworthy solution since their efficient maneuverability can aboard the rural coverage issues or not-spots.

Sweet cherry pomace is a by-product that can be a source of bioactive phenolic compounds. Usually, polyphenols have been extracted using conventional extraction methodologies. However, a significant fraction, called non-extractable polyphenols (NEPs), remains retained in the conventional extraction residues. Therefore, this work is aimed, for the first time, to investigate the release of NEPs from cherry pomace combining pressurized liquid extraction (PLE) and enzyme-assisted extraction (EAE) using Promod enzyme. A response surface methodology was employed to study the influence of temperature, time, and pH on the NEPs extraction. The response variables were the total phenolic content (TPC) measured by Folin-Ciocalteu method, total proanthocyanidin (PA) content evaluated by vanillin, DMAC, and butanol/HCl assays, and total antioxidant capacity determined by Trolox equivalent antioxidant capacity and inhibition of hydroxyl radical assays. The results indicated that PLE-EAE was more suitable and selective to obtain NEPs from sweet cherry pomace than PLE alone. In fact, the extracts obtained by PLE-EAE displayed higher TPC, PA content, and bioactivity than the extracts obtained by PLE under the same extraction conditions, and those obtained by conventional methods. Moreover, size-exclusion chromatography profiles showed that the combination of PLE and EAE enabled the recovery of NEPs with higher molecular weight than PLE without EAE treatment.

Background. Shoulder in CrossFit should have a balance between mobility and stability. Glenohumeral internal rotation deficit and posterior shoulder stiffness are risk factors for overhead shoulder injury. Objective. To determine the effectiveness of instrument assisted soft tissue mobilization and horizontal adduction stretch in CrossFit practitioners’ shoulders. Methods: Twenty-one regular CrossFitters were allocated to experimental (stretching with isometric contraction and instrument assisted soft tissue mobilization) or control group (instrument assisted soft tissue mobilization). Each session lasted 5 minutes, 2 days a week, over a period of 4 weeks. Shoulder internal rotation and horizontal adduction (digital inclinometer), and posterior shoulder stretch perception (Park scale) were evaluated. Shapiro-Wilk test was used to analyze the distribution of the sample. Parametric student's t-test was used to obtain the intragroup differences. The inter- and intra-rater differences were calculated using a repeated measures ANOVA. Results. Changes were found in the experimental group following intervention (p < 0.05), and when comparing baseline and follow-up assessments (p < .05) in all variables. Significant differences were found in the control group following intervention (p < 0.05), in right horizontal adduction and left internal rotation. When comparing perception of internal rotation and horizontal adduction in both groups in the three assessments significant differences were found. Conclusions. Instrument assisted soft tissue mobilization can improve shoulder horizontal adduction and internal rotation. An instrument-assisted soft tissue mobilization technique yields the same results alone as those achieved in combination with post-isometric stretch with shoulder adduction.

The efficiency of producing embryos using in vitro technologies in livestock species rarely exceeds the 30 to 40% threshold, indicating that the proportion of oocytes that fail to develop after in vitro fertilization and culture is considerably large. Considering that the intrinsic quality of the oocyte is one of the main factors affecting blastocyst yield, the precise identification of non-invasive cellular or molecular markers that predict oocyte competence is of major interest to research and practical applications. The aim of this review was to explore the current literature on different non-invasive markers associated with oocyte quality in the bovine model. Apart from some controversial findings, the presence of cycle-related structures in ovaries, a follicle size between 6 and 10 mm, large number of surrounding cumulus cells, slightly expanded investment without dark areas, large oocyte diameter (>120 microns), dark cytoplasm, and the presence of a round and smooth first polar body have been associated to better competence. In addition, the combination of oocyte and zygote selection by BCB test and spindle imaging have the potential to further optimize the identification of oocytes with better developmental competence for in vitro-derived technologies in livestock species.

The ectoparasitic mite Varroa destructor is the most significant pathological threat to the western honey bee, Apis mellifera, leading to the death of most colonies if left untreated. An alternative approach to chemical treatments is to selectively enhance heritable honey bee traits of resistance or tolerance to the mite through breeding programs, or select for naturally surviving untreated colonies. We conducted a literature review of all studies documenting traits of A. mellifera populations either selectively bred or naturally selected for resistance and tolerance to mite parasitism. This allowed us to conduct an analysis of the diversity, distribution and importance of the traits in different honey bee populations that can survive V. destructor throughout the globe. In a second analysis, we investigated the genetic bases of these different phenotypes by comparing ’omics studies (genomics, transcriptomics, and proteomics) of A. mellifera resistance and tolerance to the parasite. Altogether, this review provides a detailed overview of the current state of the research projects and breeding efforts against the most devastating parasite of A. mellifera. By highlighting the most promising traits of varroa-surviving bees and our current knowledge on their genetic bases, this work will help direct future research efforts and selection programs to control this pest. Additionally, by comparing the diverse populations of honey bees that exhibit the traits, this review highlights the consequences of anthropogenic and natural selection on the interactions between hosts and parasites.

In order to solve the problem of measuring the distance and position between the flanges of two pipelines on the seabed, a measuring device for pulling rope in seawater was designed. Aiming at the sealing problem of the key equipment that is the rotating shaft of the rope winch, this paper used the principle of the magnetic coupling to transfer the driving moment, and adopted the method of converting the dynamic seal into the static seal structure to realize the reliable sealing of the motor. Through the experiment of measuring two pipelines with underwater rope pulling device, it was verified that the measuring accuracy of the device meets the design requirements, and the feasibility of the application of magnetic coupling technology in winch is also verified.

Silybum marianum (L.) Gaertn. (aka milk thistle) constitute the almost exclusive source of silymarin, a mixture of different flavonolignans, and is thus considered as a unique model for their extraction. The present research deals with ultrasound-assisted extraction (UAE) of S. marianum flavonolignans and their quantification using LC system. The optimal conditions for UAE were: aqueous EtOH 54.5% (v/v) as solvent, applying an ultrasound frequency of 36.6 kHz during an extraction time of 60 min at 45°C with a liquid to solid ratio of 25:1 ml/g DW. Following optimization, the extraction method was validated according to international standards of the association of analytical communities (AOAC) in order to ensure its precision and accuracy for the quantitation of the individual silymarin components. The efficiency of UAE was compared with maceration protocol of the same duration. The optimized and validated conditions allowed highest extraction yields of flavonolignans in comparison to maceration. The antioxidant capacity of the extracts was confirmed by the CUPRAC assays and inhibition of advanced glycation end products. The skin anti-aging action was also confirmed toward the strong in vitro inhibition capacity of the obtained extract against collagenase and elastase enzymes. The procedure presented here allows a green efficient extraction and quantification of the main flavonolignans from the fruits of S. marianum with attractive antioxidant and anti-aging activities for future cosmetic applications.

This paper presents a system developed for the assistance with a collaborative robot in hand-assisted laparoscopic surgery (HALS). The system includes a sensing glove with piezoresistive sensors which capture continuously the flexion degree of the surgeon's fingers. These data are analyzed using an algorithm that detects and recognize the selected movements. This information is sent as commands to the collaborative robot throughout the surgical operation. The bending patterns, speed and execution times of the movements are modelled in a pre-phase in which it will extract all the necessary information for later detection during the motion execution. The results obtained with 10 different volunteers show a high degree of accuracy and a low false discovery rate.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

Three-Dimensional reconstruction of the corneal surface provides a powerful tool for managing corneal diseases. This study proposes a novel method for reconstructing the corneal surface from elevation point clouds, using modal schemes capable of reproducing corneal shapes using surface polynomial functions. The multivariable polynomial fitting was performed using a non-dominated sorting multivariable genetic algorithm (NS-MVGA). Standard reconstruction methods using least-squares discrete fitting (LSQ) and sequential quadratic programming (SQP) were compared with the evolutionary algorithm-based approach. The study included 49 eyes of 49 patients (ages 11-63) sorted in two groups: control (33 eyes) and keratoconus (KC) (16 eyes). Tomographic information (Sirius, Costruzione Strumenti Oftalmici, Italy) was processed using Matlab. The goodness of fit for each method was evaluated using mean squared error (MSE), measured at the same nodes where the elevation data were collected. Polynomial fitting based on NS-MVGA improves MSE values by 86% compared to LSQ-based methods in healthy patients. Moreover, this new method improves aberrated surface reconstruction by 43% for Amsler-Krumeich (AK) Grade 1 keratoconus patients. Finally, significant improvements were also found in morpho-geometric parameters, such as asphericity and corneal curvature radii.

We present a numerical illumination model to calculate direct as well as diffuse or Hapke scattered radiation scenarios on arbitrary planetary surfaces. This includes small body surfaces such as main belt asteroids as well as e.g. the lunar surface. The model is based on the raytracing method. This method is not restricted to spherical or ellipsiodal shapes but digital terrain data of arbitrary spatial resolution can be fed into the model. Solar radiation is the source of direct radiation, wavelength-dependent effects (e.g. albedo) can be accounted for. Mutual illumination of individual bodies in implemented (e.g. in binary or multiple systems) as well as self-illumination (e.g. crater floors by crater walls) by diffuse or Hapke radiation. The model is validated by statistical methods. A χ2 test is undertaken to compare simnulated images with DAWN images acquired during the survey phase at small body 4 Vesta.

The calculation of the surface tension of ordinary organic and ionic liquids, based on a computer algorithm applying a refined group-additivity method, is presented. The refinement consists of a complete breakdown of the molecules into their constituting atoms, further distinguishing them by their immediate neighbour atoms and bond constitution. The evaluation of the atom-groups’ contributions was carried out by means of a fast Gauss-Seidel fitting method founded upon the experimental data of 1895 compounds from literature. The result has been tested for plausibility using a 10-fold cross-validation (cv) procedure. The direct calculation and the cv test proved the applicability of the present method by the close similarity and excellent goodness of fit R2 and Q2 of 0.9023 and 0.8821, respectively. The respective standard deviations are ±2.01 and ±2.16 dyn/cm. Some correlation peculiarities have been observed in a series of ordinary and ionic liquids with homologous alkyl chains which are illustrated and discussed in detail, exhibiting the limit of the present method.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

This comprehensive review explores recent advancements in heavy metal remediation techniques, focusing on the utilization of cellulose-silica composites and tailored surface modification techniques. We examine the synthesis strategies and properties of cellulose-silica adsorbents, highlighting their enhanced adsorption capacities and structural robustness for removing heavy metal pollutants from aqueous environments. The review investigates various surface modification approaches, including thiol-functionalization, amino acid grafting, and silane coupling agents, for optimizing the surface chemistry and morphology of cellulose-silica composites. Mechanistic insights into the adsorption processes and kinetics of modified adsorbents are discussed, along with considerations for optimizing adsorption performance under different environmental conditions. This review provides valuable perspectives on the development of effective adsorbent materials for sustainable heavy metal remediation applications.

We present a modified characteristic finite element method that exhibits second-order spatial accuracy for solving convection-reaction-diffusion equations on surfaces. The temporal direction adopted backward-Euler method, while the spatial direction employed surface finite element method. In contrast to regular domains, it is observed that the point in the characteristic direction traverses the surface only once within a brief time. Thus, the good approximation of the solution in the characteristic direction holds significant importance for the numerical scheme. In this regard, Taylor expansion is employed to reconstruct the solution beyond the surface in the characteristic direction. The stability of our scheme is then proved. A comparison is made with an existing characteristic finite element method based on face mesh. Numerical examples are provided to validate the effectiveness of our proposed method.

AISI 1050 steel circular pocket milling under minimum quantity lubrication (MQL) surroundings including nozzle elevation angle, lubricant flow rate, air pressure and cutting speed was studied. The machined surface quality (Ra) was evaluated for Up-milling side and Down-milling side. In this study, to obtain an manifest explanation on the pivotal effective parameters of MQL surroundings and cutting speed on the machined surface quality (Ra) through analyzing Taguchi L9 (34-2) approach and ANOVA calculation to identify those parameters, by utilizing the experimental outcomes to interpret three-dimensional (3D) surface plots and the diagrams of Signal-to-Noise ratios and major impact plots of Mean. The obtained outcomes of optimal operating parameters indicated that the pivotal effective parameters of MQL surroundings are nozzle elevation angle and lubricant flow rate on the machined surface quality. Simultaneously, a quadratic mathematical paradigm generated by using response surface design (RSD) and desirableness function evaluation were utilized to forecast the optimal values of the machined surface quality compared to Taguchi method. The results unveiled that the optimal values of the machined surface quality are adjacent to experimental attained values. The machined surface quality has been significantly improved using MQL surroundings.

In this study, an investigation on the influence of In-situ tribo-oxide-layer on non-lubricated tribological behaviours of LM27/SiCp composites was carried out at different applied loads. The variations in wear performance and microstructure of brake lining friction material (LM27) with the addition of different amounts and sizes of SiCp are explored. For this purpose, LM27/SiCp composite materials were manufactured by stir casting route varying the amount of particle reinforced from 3wt.% to 12wt.% with a different size range (fine: 1-20µm and coarse: 106-125µm). Non-lubricated dry wear tests of LM27/SiCp composites samples were trialled at different loads from 9.8N to 49N by using a pin-on-disc machine system. At a contact pressure of 0.2-1 MPa, LM27/SiCp composites with 12wt.% reinforcement showed a lower coefficient of friction than other composites. In-situ formation of oxide layers on the contact region of the specimen supports the self-lubrication during the wear test, which is responsible for better wear performance of LM27/SiCp composites. However, these study portraits that composite with 12wt. % fine size SiCp exhibits better wear performance in comparison to the other developed composites.

Nobel metal nanohole arrays have been used extensively in chemical and biological systems due to their fascinating optical properties. Gold nanohole arrays (Au NHAs) were prepared as surface plasmon polaritons (SPP) generators for the surface-enhanced sum-frequency generation (SFG) detection of 4-Mercaptobenzonitrile (4-MBN). The angle-resolved reflectance spectra revealed that the Au NHAs have three angle-dependent SPP modes and two non-dispersive localized surface plasmon resonance (LSPR) modes under different structural orientation angles (sample surface orientation). An enhancement factor of ~30 was achieved when the SPP and LSPR modes of the Au NHAs were tuned to match the incident visible (VIS) and output SFG, respectively. This multi-mode matching strategy provided flexible controls and selective spectral windows for surface-enhanced measurements, and was especially useful in nonlinear spectroscopy where more than one light beam involved. The structural orientation- and power-dependent performance demonstrated the potential of plasmonic NHAs in SFG and other nonlinear sensing applications, and provided a promising surface molecular analysis development platform.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

In this study, the values of the interfacial energies of seven different polymer-water systems obtained by Sessile Drop Accelerometry (SDACC) are compared with the values obtained by the Young’s-equation-based Owens-Wendt method. The SDACC laboratory instrument –a combination of a drop shape analyzer with high-speed camera and a microgravity tower- and the evaluation algorithms, are designed to measure the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on Thermodynamics of Interfaces and differs from the conventional aproach of the two hundred-years-old Young’s equation in that it assumes a thermodynamic equilibrium between interfaces, rather than a balance of forces on a point of the solid-liquid-gas contour line. A comparison of the mathematical model that supports the SDACC method with the widely accepted Young`s equation is discussed in detail in this study.

A new method, the sessile drop accelerometry (SDACC) for the study and measurement of the interfacial energies of solid-liquid-gas systems, is tested and discussed in this study. The laboratory instrument and technique –a combination of a drop shape analyzer with high-speed camera and a laboratory drop tower- and the evaluation algorithms, were designed to calculate the interfacial energies as a function of the geometrical changes of a sessile droplet shape due to the effect of “switching off” gravity during the experiment. The method bases on the thermodynamic equilibrium of the system interfaces and not on the balance of bi-dimensional tensions on the solid-liquid-gas contour line. A comparison of the mathematical model that supports the method with the widely accepted Young`s equation is discussed in this study.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

This paper constitutes an original and new methodology for the determination of the surface properties of carbon fibers in the two oxidized and untreated forms by inverse gas chromatography technique at infinite dilution based on the effect of the temperature on the surface area of the various organic molecules adsorbed on the carbon fibers. The studied thermal effect proved a large deviation of the classical methods or models relative to the new determination of the surface properties of carbon fibers, such as the dispersive component of their surface energy, the free surface energy, the free specific energy, the enthalpy and entropy of adsorption of molecules on the carbon fibers. The obtained specific enthalpy and entropy of adsorption for the polar solvents led to the determination of the Lewis’s acid-base constants of carbon fibers. Different molecular models and chromatographic methods were used to quantify the surface thermodynamic properties of carbon fibers and compared to the thermal model. The obtained results proved that the oxidized carbon fibers gave more specific interaction energy and greater acid-base constants than that of the untreated carbon fibers and thus highlighting the important role of the oxidization on the acid-base of fibers. The determination of the specific acid-base surface energy of the two carbon fibers showed greater values of the oxidized carbon fibers relative to the untreated carbon fibers. An important basic character was highlighted for the two studied carbon fibers, larger than the acidic character. It was observed that the Lewis’s acid-base constants of the oxidized carbon fibers are larger than that of the untreated fibers with more accentuated basic charterer. This result was confirmed by all molecular models and chromatographic methods.

Robot workpiece machining is interesting in industry since it offers some advantages, such as higher flexibility in comparison with the conventional approach based on the CNC technology. However, in recent years we have been facing a strong progressive shift to custom based manufacturing and low volume/high mix production, which require a novel approach to automation by the employment of collaborative robotics. However, collaborative robots feature only limited motion capability, to provide safety in cooperation with human workers. Thus, it is highly necessary to perform more detailed robot task planning to ensure its feasibility and optimal performance. In this paper, we deal with the problem of studying kinematic robot performance in the case of such manufacturing tasks, where the robot tool is constrained to follow the machining path embedded on the workpiece surface at a prescribed orientation. The presented approach is based on the well-known concept of manipulability, although the latter suffers from physical inconsistency due to mixing different units of linear and angular velocity in a general 6 DOF task case. Therefore, we introduce the characteristics of the workpiece surface constraint in the robot kinematic analysis, that enables evaluation of its available velocity capability in a reduced dimension space. Such constrained robot kinematics transform the robot`s task space to a two-dimensional surface tangent plane, and the manipulability analysis may be limited to the space of linear velocity only. Thus, the problem of physical inconsistency is avoided effectively. We show the theoretical derivation of the proposed method, which was verified by numerical experiments.

The performance and lifespan of cutting tools are significantly influenced by their surface quality. The present report highlights recent advances in enhancing the surface characteristics of tungsten carbide and high-speed steel cutting tools using a novel micro-machining technique for polishing and edge-honing. Notably, the main aim is to reduce the surface roughness while maintaining the hardness of the materials at an optimal level. By conducting a thorough analysis, of surfaces obtained with different techniques. It was that micro-machining method effectively decreased the surface roughness of the cutting tools, most effectively of the techniques investigated. Significantly, the surface roughness is reduced from an initial measurement of 400 nm to an impressive value of 60 nm. No significant change in hardness was observed, which guarantees the maintenance of the mechanical properties of the cutting tools. This analysis enhances the comprehension of surface enhancement methodologies for cutting tools through the presentation of these findings. The observed decrease in surface roughness, along with the consistent hardness, exhibits potential for improving tool performance. These enhancements possess the capacity to optimise manufacturing processes, increase tool reliability, and minimise waste generation.

Eastern boundary upwelling systems feature strong zonal gradients of physical and biological ocean properties between cool, productive coastal oceans and warm, oligotrophic subtropical gyres. Zonal currents and jets (striations) are therefore likely to contribute to the transport of water properties between coastal and open oceanic regions. Multi-sensor satellite data are used to characterize the signatures of striations in sea surface temperature (SST), salinity (SSS), and chlorophyll-a (Chl-a) in subtropical eastern North/South Pacific (ENP/ESP) upwelling systems. In the ENP, tracers exhibit striated patterns extending up to ~2500 km offshore. Striations in SST and SSS are highly correlated with quasi-zonal jets, suggesting that these jets contribute to SST/SSS mesoscale patterns via zonal advection. Chl-a striations are collocated with sea surface height (SSH) bands, a possible result of mesoscale eddy trains trapping nutrients and forming striated signals. In the ESP, striations are only found in SST and coincide with SSH bands, consistently with quasi-zonal jets located outside major zonal tracer gradients. An interplay between large-scale SST/SSS advection by the quasi-zonal jets, mesoscale SST/SSS advection by the large-scale meridional flow and eddy advection may explain the persistent ENP hydrographic striations. These results underline the importance of quasi-zonal jets for surface tracer structuring at the mesoscale.

Management practices must be developed to improve yam production sustainability. Image-based phenotyping techniques could help developing such practices based on non-destructive analyses of important plant traits. Our objective was to determine the potential of image-based phenotyping methods to assess traits relevant for tuber yield formation in yam grown in glasshouse and field. We took plant and leaf pictures with consumer cameras. We used the numbers of image pixels to derive the shoot biomass and the total leaf surface and calculated the ‘triangular greenness index’ (TGI) which is an indicator of the plant nitrogen (N) nutritional status. Under glasshouse conditions, the number of pixels obtained from nadir view (image taken top down) was positively correlated to the shoot biomass, and the total leaf surface, while the TGI was negatively correlated to the N content of diagnostic leaves. Under field conditions, pictures taken from the nadir view showed an increase in soil surface cover and a decrease in TGI with time. TGI was negatively correlated to SPAD measured on specific leaves but was not correlated to the N content of these leaves. In conclusion, these phenotyping techniques deliver relevant results but need to be further developed and validated for application in yam.

Deformation of the surface of diamagnetic liquid by magnetic field is called the “Moses Effect”. Physics and applications of the direct and inverse Moses effects are reviewed. Experimental techniques enabling visualization of the effects are surveyed. Impact of magnetic field on micro- and macroscopic properties of liquids is addressed. Influence of the surface tension on the shape of the near-surface dip formed in a diamagnetic liquid by magnetic field is reported. Floating of diamagnetic bodies driven by the Moses effect is treated. The effect of the “magnetic memory of water” in its relation to the Moses Effect is discussed. The dynamics of self-healing of near-surface dips due to the Moses Effect is considered.

Infertility affects millions worldwide, posing a significant global health challenge. The proteomic analysis of follicular fluid provides a comprehensive view of the complex molecular landscape within ovarian follicles, offering valuable information on the factors influencing oocyte development and on the overall reproductive health. The follicular fluid is derived from the plasma and contains various proteins that can have different roles in oocyte health and infertility and this fluid is a critical microenvironment for the developing oocytes as well. Using HPLC/MS method we investigated the protein composition of the follicular fluid and after classification we did relative quantification of the identified proteins in the pregnant (P) and non-pregnant (NP) groups. Based on the protein-protein interaction analysis ALB and ApoA1 was found to be hub proteins and the quantitative comparison of the P and NP groups resulted significantly lower concentration of ApoA1 and HDL-cholesterol in the P group. As both molecules are involved in the cholesterol transport, we also investigated their role in the development of oocytes and in the prediction of fertility.

The feasibility of recovering bioactive antioxidants from Phyllantus emblica leaves using ethanol -water mixture (0 – 100%) and heat-assisted extraction technology (HAE-T) was investigated in this present study. To this effect, the process parameter of operating temperature (OT: 30 -50 oC), solid -to-liquid ratio (S:L: 1:20 - 1:60 g/mL) and extraction time (ET: 45 - 180 min) were investigated on the extract total phenolic content (TPC, mg GAE/g d.w), yield (EY, %) and antioxidant activity (μM AAE/g d.w) by employing the Box-Behnken experimental design (BBD) available in response surface methodology (RSM). Multi-objective process optimization using the desirability function algorithm to determine set of process variables that simultaneously optimize process responses of TPC, EY and AA was also investigated. The recovery process was thereafter modeled with BBD-RSM and multi gene genetic programming (MGGP) algorithm and model reliability assessment via Monte Carlo simulation were conducted for the best performing set of models for predicting TPC, EY and AA values. The HPLC characterization of the recovered extract was carried out to ascertain the phenolic compound constituents of the Phyllantus emblica leaf extract. The 50% ethanol solution was found to be the best for the optimal extraction of antioxidants from Phyllantus emblica leaves. The HAE-T was suitable for recovering bioactive extract from Phyllantus emblica leaves and investigated process parameters have impacts on the recovery process. The process parameters that simultaneously gave the optimum EY of 21.6565%, TPC of 67.116 mg GAE/g and AA of 3.68583 µM AAE/g were OT of 41.61 oC, S:L of 1:60 g/mL and ET of 180 min. The HPLC extract profiling revealed that the bioactive constituents present in the recovered extract were betulinic acid, gallic acid, chlorogenic acid, caffeic acid, ellagic acid, and ferulic acid. Both the developed BBD-RSM and evolved MGGP-based models predicted the observed process response of TPC, EY and AA satisfactorily with BBD-RSM models marginally better in their predictions. The reliability results showed that the BBD-RSM models predicted TPC, EY and AA values with high certainty of 99.985%, 97.569% and 98.661%, respectively.

When analyzing user geospatial information through deep learning methods, it is typically necessary to annotate existing geospatial data. Currently, manual annotation methods are commonly employed, suffering from issues related to low efficiency and accuracy. This design is based on the TensorFlow deep learning framework and first realizes the BiLSTM+CRF+AGG deep learning model. Among the models, AGG is the aggregation layer, which is introduced to solve the problem of solid particle size equilibrium. Secondly, based on the characteristics of original data and professional data, an automatic labeling algorithm is proposed. The algorithm first preprocesses the acquired original data set and professional data set, The most valuable unlabeled data set which can make the training model converge quickly is selected from the original data set as the target data set. Sort the target data set based on preset rules and set annotation parameters for the sorted target data set. Based on the set annotation parameters, the corpus is synthesized and used as the annotation result. Thirdly, based on the active learning strategy, a manual annotation auxiliary scheme is proposed, and an Excel generation module that is convenient for manual annotation correction is designed and developed to further improve the efficiency and quality of annotation through iterative processing. The combination of the BiLSTM+CRF+AGG deep learning model and high-quality annotation can accurately identify non-standard, incomplete, or even incorrect geographical information entities. This annotation method has found successful practical application within the context of the research project and has been granted an invention patent.

This study examined the eye movement patterns of 317 elementary students across reading conditions (audio-assisted reading (AR) and reading-only (R)) and text types (fiction and non-fiction), and identified eye movement parameters that predict their literal comprehension (LC) and inferential comprehension (IC). Participants, randomly assigned to either reading condition and either text type, answered questions assessing their LC and IC. Average fixation duration (AFD), total fixation duration (TFD), and scanpath length were used as eye movement parameters. There were main effects of age on all parameters and interaction effects between age and reading condition on TFD and scanpath length. Controlling for age, TFD had a positive impact on LC of both text types in the AR, while under the R, it affected negatively on IC of both text types. Longer scanpaths predicted IC of fiction in the AR, LC and IC of non-fiction under the AR, and LC of non-fiction within the R. AFD influenced negatively on IC of fiction in the AR, LC and IC of non-fiction in the AR, and LC of non-fiction under the R. These eye movement patterns and predictors indicate children employ different reading strategies based on reading modality and text type.

Ovarian hyperstimulation syndrome (OHSS) is the main severe complication of the ovarian stimulation for in vitro fertilization (IVF) cycles. The aim of the current study was to identify the interventions for prevention of and reduction in the incidence and severity of OHSS in patients who undergo IVF not included in systematic reviews with meta-analysis of randomized controlled trials (RCTs), assess and grade their efficacy and evidence base. The best available evidence for each specific intervention was identify, analyzed in terms of safety/efficacy ratio and of risk of bias, and graded using Oxford Centre for Evidence-Based Medicine (CEBM) hierarchy of evidence. A total of 15 interventions to prevent OHSS were included in the final analysis. In IVF population not at high risk for OHSS, follitropin delta for ovarian stimulation may reduce the incidence of early OHSS and/or preventive interventions for early OHSS. In high-risk patients, inositol pretreatment, ovulation triggering with low doses of urinary hCG, and the luteal phase administration of GnRH antagonist may reduce the OHSS risk. In conclusion, even if not supported by systematic reviews with homogeneity of the RCTs, several treatments/strategies to reduce the incidence and severity of OHSS have shown to be promising.

The objective of this study was to assess the impact of different inoculation technologies on the aerobic biological semi-decomposition process of bokashi-type biofertilizer formulations. We examined their effects on the chemical and biological quality of the product, as well as their influence on the agronomic and nutritional characteristics of red-beet and cabbage crops in the field. The highest yields of field-grown beet crops were obtained from seedlings produced using the following treatments: bokashi biofertilizer + biodynamic preparations 502-507 BPB (62.6 Mg ha-1), bokashi + Chamomilla 12CH (60.2 Mg ha-1), and bokashi + Carbo vegetabilis 12 CH (56.3 Mg ha-1). These results corresponded to an increase of 60.9%, 54.7%, and 44.7%, respectively, compared to the yield of the control treatment (38.9 Mg ha-1). The increase in productivity of cabbage plants was higher in the treatment bokashi + Calcarea carbônica 12 CH (35.8 Mg ha-1), being 148.6% higher than the control (14.4 Mg ha-1).The content of moisture, carbon, nitrogen, C/N ratio, and pH H2O in the majority of the evaluated formulations, comply with the standards outlined in IN Nº 61, 2020, by Ministry of Agriculture, Fisheries and Supply, qualifying them as class "A" solid organic compound fertilizers.

Background: Primary lymphedema is a chronic condition caused by a developmental abnormality of the lymphatic system and its malfunction. Different surgical options such as physiologic and excisional procedures have been proposed. The aim of this study was to present a complete algorithm for the treatment of primary lower extremity lymphedema: Primary LYmphedema Multidisciplinary Approach (P-LYMA). Methods: Nineteen patients were treated according to the P-LYMA. Patients underwent pre- and post-operative complex decongestive therapy (CDT). Different physiologic and excisional procedures were performed independently or in combination. The primary outcome was the circumferential reduction rate (CRR). The Lymphedema Quality of Life Score (LeQOLiS), reduction in the number of episodes of cellulitis, length of stay, and complications were recorded. Results: The mean CRR calculated was 72.8±19.6% after twelve months. The episodes of cellulitis per year decreased from a mean of 1.9±0.8 preoperative to 0.4± 0.6 throughtout follow-up. Two patients experienced minor complications. Mean hospitalization time was 5 days. Patients’ quality of life (LeQOLi score) drastically improved from 70.4±11.6 to 24.2 ±13.9 at twelve months post-op. Conclusion: The P-LYMA algorithm allows to maximize surgical results and improve the quality-of life in patients who suffer from primary lymphedema. CDT is mandatory to optimize results.

The ultrasonic vibration assisted pressing process can improve the fluidity, the uneven distribution of density and particle size of WC-Co powder. However, the microscopic mechanism of ultrasonic vibration on the powder remains unclear. In this paper, WC and Co particles are simulated by three-dimensional spherical models of two particle sizes with the aide of the secondary development of Python. At the same time, the forming process of powder at mesoscale is simulated in the virtue of the finite element analysis software ABAQUS. The influence of vibration amplitude on the fluidity, the filling density and the stress distribution of WC-Co powder is investigated when the ultrasonic vibration is applied to the conventional pressing process. From simulation results, the ultrasonic vibration amplitude has great influences on the density of the compact. With the increase of the ultrasonic amplitude, the compact density also increases gradually. At the initial stage of the compaction, the particles move violently under the action of ultrasonic vibration, the fluidity is obviously enhanced, the arch bridge effect between particles is destroyed, the fine particles quickly fill the pores between the large particles, which increase the density, and the residual stress in the billet decreases after the compaction. From the experimental results, the size distribution of the billet is more uniform, the elastic aftereffect is reduced, the dimensional instability is improved, and the density curves obtained by experiment and simulation are within a reasonable error range.

The standard treatment for early-stage lung cancer is complete tumor excision by limited resection of the lung. Pre-operative localization is used before video-assisted thoracoscopic surgery (VATS) to improve the accuracy of pulmonary nodule excision. However, lung atelectasis and hypoxia resulting from controlling apnea during the localization procedure may affect the localization accuracy. Pre-procedural pulmonary recruitment may improve respiratory mechanics and oxygenation during localization. In this study, we investigated the potential benefits of pre-localization pulmonary recruitment prior to pulmonary ground-glass nodule localization in a hybrid operating room. We hypothesized that pre-localization pulmonary recruitment would increase localization accuracy, improve oxygenation, and prevent the need for re-inflation during the localization procedure. We retrospectively enrolled patients with multiple pulmonary nodule localizations before surgical intervention in our hybrid operating room. We compared localization accuracies between patients who had undergone pre-procedure pulmonary recruitment and patients who had not. Saturation, re-inflation rate, apnea time, procedure-related pneumothorax, and procedure time were also recorded as secondary outcomes. Patients who had undergone pre-procedure recruitment had better saturation, shorter procedure time, and higher localization accuracy. The pre-procedure pulmonary recruitment maneuver was effective in increasing regional lung ventilation, leading to improved oxygenation and localization accuracy.

One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.

Almond (Prunus dulcis (Mill.) D.A.Webb) is one of the most important nut crops both in terms of area and production. Over the last decades, an important part of the beneficial actions for health associated with their consumption was attributed to the phenolic compounds, mainly accumulated in almond skin. Interestingly, after cold-pressed oil extraction, most of these antioxidant phenolic compounds are retained in a skin-enriched by-product, so-called almond cold-pressed oil residue. In Morocco, ranked fifth producer in the world, this production generates an important part of this valuable byproduct. In the present study, using a multivariate Box-Behnken design, an ultrasound-assisted extraction (USAE) method of phenolic compounds from Moroccan almond cold-pressed oil residue was developed and validated. Response surface methodology resulted in the optimal extraction conditions: the use of aqueous EtOH 53.0% (v/v) as green solvent, applying an US frequency of 27.0 kHz for an extraction duration of 29.4 min. The present USAE allowed substantial gains in terms of extraction efficiency compared to conventional heat reflux extraction. Applied to 3 different local Beldi genotypes growing at 3 different experimental sites, the optimal USAE conditions led to a total phenolic content of 13.86 mg/g dry weight (DW). HPLC analysis revealed that the main phenolic compounds from this valuable byproduct were: chlorogenic acid followed by protocatechuic acid, p-hydrobenzoic acid and p-coumaric acid. The accumulation of these phenolic compounds appeared to be more dependent on the genetic background than on the environmental impact here represented by the 3 experimental culture sites. Both in vitro cell free and cellular antioxidant assays were performed, and revealed the great potential of these extracts. In particular, correlation analysis evidenced the prominent roles of chlorogenic acid, protocatechuic acid and p-hydrobenzoic acid. To summarize, the USAE method presented here is a quick, green, simple and efficient validated USAE for the possible valorization of antioxidant phenolic compounds from Moroccan almond cold-Pressed oil residues, making it possible to generate extracts with attractive antioxidant activities for future nutraceutical and/or cosmetic applications.

This paper questions the potential shift of reproduction towards assisted reproductive technologies due to benefits provided by genetic manipulation of embryos. In order to examine the viability of such a shift and its implications from a regulatory perspective, we relied on two panels of experts from Israel and Spain, using the Delphi method and a series of in-depth interviews. We anticipate, at a first stage, a continuous-steady growth in the use of IVF, supplemented by preimplantation genetic diagnosis and the introduction of CRISPR/Cas. At a second stage, attracting a growing share of fertile people would require developments in genomics. While it is unclear whether these developments will fully materialize, they could be replaced by technoscientific imaginaries generating perceived benefits. We conclude that the regulation of reproductive genetics is becoming more critical and complex. The aim should be to ensure good practices and equity, while providing more information to the public. A broad and inclusive societal debate may overcome the difficulty of drawing a clear line between medical uses and non-medical uses of genetic selection and engineering and may contribute to finding the right balance between allowing autonomous decisions of patients and protecting the public interest.

Based on the demographic shift and the related challenges resulting from the growing number of elderly and persons with chronic diseases, the idea of smart home that supports its inhabitants in the daily life, gains importance. The purpose of this paper was to examine in a prototypic Ambient Assisted Living environment if users after interaction with different health-supporting applications intend to use such in the future. Two experimental studies exemplary show possible applications of home-integrated technology that can support, assist and accompany the target group in different contexts, and examine to what extent participants are willing to future use such sophisticated technology at home. The results show that people in general, but especially the old and chronically ill ones are quite fascinated of health-supporting ambient technology and the majority intends to use such ambient assistance in the future (study I). Moreover, serious games for healthcare are shown as a hedonic use of technology in smart homes that have a great potential to retain or improve the physical health, mobility and the overall well-being of the inhabitants (study II). The article provides two examples of ambient technology to leverage the demographic change and presents important user factors for facilitating high user acceptance.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

In this study, Fe-Mo-B based hardfacing electrodes containing different amounts of Mo were coated on an AISI 1020 steel substrate using the electric arc welding method. The findings show that molybdenum is highly effective on the microstructure and minor changes in the coating composition affect the phases and morphological properties. In the hardness tests, an increase of 73% was achieved in the Fe14Mo2B4 based hardfacing coating compared to the base material and a 30% increase compared to the Fe16B4 based coating. The highest macro hardness value was measured as 56.4 HRC and the highest phase hardness was measured as 3228 HV in the FeMo2B2 phase. The lowest wear rate was measured in the Fe14Mo2B2 based coating. The wear rate of the Fe14Mo2B4 based coating was 8.1 times lower than that of the substrate material and 4.7 times lower than that of the Fe16B4 based coating. According to corrosion test results, the highest corrosion resistance was obtained in Fe16B4 based coating. The current density value of the Fe16B4 based coating was measured to be 13.6 times lower than that of the substrate material.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.