Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

This paper examines interlinkages and hedging opportunities between nine major cryptocurrencies for the period between 30 September 2015 and 4 June 2020, which notably includes the coronavirus disease 2019 (COVID-19) outbreak lasting from early 2020 through the end of the sample period. The results of dynamic conditional correlation (DCC) analysis using a minimum connectedness approach show a high degree of correlation between cryptocurrencies throughout the sample period. However, the correlations reach their minimum values during the COVID-19 pandemic, which indicates that cryptocurrencies acted as a hedge or safe haven during the stressful period of the COVID-19 pandemic. The weight of cryptocurrencies was significantly reduced and their hedging effectiveness varied greatly during the pandemic, which indicates that investors’ preferences changed during the COVID-19 period.

Besides external high-energy photon or proton beam therapy, targeted radionuclide therapy (TRNT) is an alternative approach to deliver radiation to cancer cells. TRNT is distributed within the body by the vascular system and allows targeted irradiation of a primary tumor and all its metastases, resulting in substantially less collateral damage to normal tissues as compared to ex-ternal beam radiotherapy (EBRT). It is a systemic cancer therapy, tackling systemic spread of the disease, which is the cause of death in most cancer patients. The α-emitting radionuclide bis-muth-213 (213Bi) has interesting properties and can be considered as a magic bullet for TRNT. The benefits and drawbacks of targeted alpha therapy with 213Bi are discussed in this review, covering the entire chain from radionuclide production to bedside. First, the radionuclide properties and production of 225Ac and its daughter 213Bi are discussed, followed by the fundamental chemical properties of bismuth. Next, an overview of available acyclic and macrocyclic bifunctional chelators for bismuth, and general considerations for designing a 213Bi-radiopharmaceutical are provided. Finally, we will provide an overview of preclinical and clinical studies involving 213Bi-radiopharmaceuticals, as well as the future perspectives of this promising cancer treatment option.

Different machine learning models (multiple linear regression, vector support machines, artificial neural networks and random forests) are applied to predict the monthly global irradiation (MGI) from different input variables (latitude, longitude and altitude of meteorological station, month, average temperatures, among others) of different areas of Galicia (Spain). The models were trained, validated and queried using data from three stations, and each best machine model was checked in two independent stations. The results obtained confirmed that the best ML methodology is the ANN model which presents the lowest RMSE value in the validation and querying phases 122.6·10kJ/(m2∙day) and 113.6·10kJ/(m2∙day), respectively, and predict conveniently for independent stations, 201.3·10kJ/(m2∙day) and 209.4·10kJ/(m2∙day), respectively. Given the good results obtained, it is convenient to continue with the design of artificial neural networks applied to the analysis of monthly global irradiation.

This research is aimed at evaluating two different scenarios, firstly, appraising the impacts of employing the concepts of Total Quality Management (TQM) to the construction projects in Saudi Arabia. The results of the study were obtained through utilization of a descriptive analytical approach, where 300 questionnaires were distributed to engineering firms and companies with a response rate of 200 questionnaires, hence achieving the study sample for this research. The data gathered was analyzed by applying the Statistical Package for Social Science (SPSS) program and calculating the Relative importance index (RII) and the mean values. From the research conducted, the outcomes showed that the management’s ability to commit using TQM while applying BIM obtained a relative importance of (0.717), while the relative importance for the management’s ability to commit using TQM without the application of BIM is (0.552). The results showed that construction projects in Saudi Arabia still sustain setbacks from applying TQM concepts and suffer from the lack of administrative, scientific and technical applications. In a second scenario, a hybridized support vector regression (SVR) Harris-hawks optimization (HHO) (i.e., SVR-HHO) were used to predict the TQM. The performance accuracy of the models was checked through three different evaluation metrics namely; mean square error (MSE), correlation co-efficient (CC) and Nash-Sutcliffe efficiency (NSE). the hybridized emerging SVR-HHO outperformed the other two data driven approaches in both the training and testing stages based on the employed evaluation metrics. Overall, the obtained results showed that both the machine learning and metaheuristic approaches were capable of predicting TQM.

ClinVar is a web platform that stores around 774k curated entries, which allows exploring genetic variants and their associations with complex phenotypes. A partial set of ClinVar’s genetic associations were reported with conflict of interpretation or uncertain clinical impact significance, which currently challenges clinicians and geneticists. Here, we evaluate the performance of data pre-processing methods combined with classical prediction methods, such as Naive Bayes, Random Forest, and Support Vector Machine to build a meta-prediction model aiming to improve genetic pathogenicity interpretation. Models were trained with ClinVar data (September 2020), and genetic variants were annotated with eight functional impact predictors catalogued with SnpEff/SnpSift (v4.3). A 10-fold cross-validation strategy was performed for evaluation by accuracy, F1-Score, Receiver Operating Characteristic, Area Under Curve. The best meta-prediction model raises by combining one-hot encoding with tree-based classifiers as Random Forest, which shows Area Under Curve ≥ 0,93. We predict pathogenicity for 109k genetic variants, which were found labeled as uncertain significance or conflict of interpretation. Additionally, we implemented AmazonForest (https://www.lghm.ufpa.br/amazonforest), a web tool to query data for a set of 5k variants that were predicted with high pathogenic probability (RFprob >= 0.9).

In Brazil, malaria transmission is mostly confined to the Amazon, where substantial progress has been achieved towards disease control in the past decade. Vector control has been historically considered a fundamental part of the main malaria control programs implemented in Brazil. However, the conventional vector-control tools have been insufficient to eliminate local vector populations due to the complexity of the Amazonian rainforest environment and ecological features of malaria vector species in the Amazon, especially Anopheles darlingi. Malaria elimination in Brazil and worldwide eradication will require a combination of conventional and new approaches that takes into account the regional specificities of vector populations and malaria transmission dynamics. Here we present an overview on both conventional and novel promising vector-focused tools to curb malaria transmission in the Brazilian Amazon. If well designed and employed, these new vector-based approaches may improve the implementation of malaria-control programs, particularly in remote or difficult-to-access areas and in regions where existing interventions have been unable to eliminate disease transmission. However, much effort still has to be put on research expanding the knowledge of neotropical malaria vectors to set the steppingstones for the development of such innovative tools.

This paper presents a Multilayer Perceptron and Support Vector Machine algorithms approach to predict the number of COVID19 infections in different countries of America. It intends to serve as a tool for decision-making and tackling the pandemic that the world is currently facing. The models were trained and tested using open data from the European Union repository where a time series of confirmed contagious cases was modeled until May 25, 2020. The hyperparameters as number of neurons per layer were set up using a tabu list algorithm. The countries selected to carry out the study were Brazil, Chile, Colombia, Mexico, Peru and the United States. The metrics used are Pearson's correlation coefficient (CP), Mean Absolute Error (MAE), and Mean Percentage Error (MPE). For the testing stage we obtained the following results: Brazil, CP=0.65, MAE=2508 and MPE=17%; Chile, CP=0.64, MAE=504, MPE=16%; Colombia, CP=0.83, MAE=76, MPE=9%; Mexico, CP=0.77, MAE=231, MPE=9%; Peru, CP=0.76, MAE=686, MPE=18% and the United States of America, CP=0.93, MAE=799, MPE=4%. This resulted in powerful machine learning tools although it is necessary to use specific algorithms depending on the data and the stage of the country’s pandemic.

Although Support Vector Machines (SVM) are widely used for classifying human motion patterns, their application in the automatic recognition of dynamic and static activities of daily life in the healthy older adults is limited. Using a body mounted wireless inertial measurement unit (IMU), this paper explores the use of SVM approach for classifying dynamic (walking) and static (sitting, standing and lying) activities of the older adults. Specifically, data formatting and feature extraction methods associated with IMU signals are discussed. To evaluate the performance of the SVM algorithm, the effects of two parameters involved in SVM algorithm—the soft margin constant C and the kernel function parameter $\mathsf{\gamma }$—are investigated. The changes associated with adding white-noise and pink-noise on these two parameters along with adding different sources of movement variations (i.e., localized muscle fatigue and mixed activities) are further discussed. The results indicate that the SVM algorithm is capable of keeping high overall accuracy by adjusting the two parameters for dynamic as well as static activities, and may be applied as a tool for automatically identifying dynamic and static activities of daily life in the older adults.

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

Virtual Histology- Intravascular Ultrasound (VH-IVUS) image is an available method for visualizing plaque component to detect thin cap fibroatheroma. Nevertheless, this imaging modality has considerable limitations to extract the plaque component features and identifying the TCFA plaque. The aim of this paper is to improve the identification of TCFA using fusion of IVUS and VH-IVUS images. In order to generate the automatic technique for reducing the human interaction, a new method namely Active Contour based Plaque Border Detection (ACPB) is proposed. In order to perform the pixel wise classification, hybrid of K-means algorithm with Particle Swarm Optimization and Plaque based Minimum Euclidean Distance (KMPSO-PMED) method is presented to classify the plaque region as well. Moreover, to obtain more significant information of imaging modalities, fusion of two different images consisting of VH-IVUS and IVUS is performed. Therefore, geometric features are extracted from the plaque region and combine with IVUS features. Furthermore, different group of plaque features are divided by means of the histopathological studies. SVM classifiers is applied to detect the TCFA and non-TCFA plaques. The proposed method is applied on 566 in-vivo IVUS and their matching VH-IVUS images obtained from 9 patients. The best result of SVM illustrates the accuracy rates of 99.41% for classification of TCFA plaque. The results prove that the highest accuracy is achieved by integrated features of IVUS and VH-IVUS images.

Using assembly theory, we investigate the assembly pathways of binary strings of length N formed by joining bits present in the assembly pool and the strings that entered the pool as a result of previous joining operations. We show that the string assembly index is bounded from below by the shortest addition chain for N, and we conjecture about the form of the upper bound. We define the degree of causation for the minimum assembly index and show that for certain N it features regularities that can be used to determine a shortest addition chain. We show that a string with the smallest assembly index for N can be assembled by a binary program of length equal to this index if the length of this string is expressible as a product of Fibonacci numbers. We conjecture that there is no binary program that has a length shorter than the length of the string having the largest assembly index for N that could assemble this string. The results confirm that four Planck areas provide a minimum information capacity that corresponds to a minimum thermodynamic (Bekenstein-Hawking) entropy. Knowing that the problem of determining the assembly index is at least NP-complete, we conjecture that this problem is NP-complete, while the problem of creating the string so that it would have a predetermined largest assembly index is NP-hard. The proof of this conjecture would imply P ≠ NP, since every computable problem and every computable solution can be encoded as a finite binary string.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Inhibition of quorum sensing (QS)-dependent biofilm formation and virulence is extensively investigated as a novel approach to combat bacterial pathogens by impeding their ability to cause antibiotic-tolerant diseases. Such strategies are considered a promising alternative to conventional antibacterial therapy since interrupting the central cell-to-cell communication system imposes less selective pressure on the target pathogen. In this study, novel hybrid compounds composed of anthranilic acids substituted with halogens at different positions of the phenyl ring, and 4-(2-aminoethyl/4-aminobuthyl)amino-7-chloroquinoline linked via 1,3,4-oxadiazole were synthesized using standard procedures. Their anti-QS activities were evaluated using Chromobacterium violaceum ATCC31532 (anti-biofilm and bactericidal activities) and Pseudomonas aeruginosa PAO1 (anti-biofilm/-virulence activities). The results showed that compounds 15–19 and 23 inhibited the production of violacein, the QS-inducible pigment, in C. violaceum to a similar extent as the model QS inhibitor - quercetin (83.5–90%). Compound 15 exhibited the strongest effect on P. aeruginosa in the anti-biofilm screening, reducing its ability to form biofilm by almost 50%, while compounds 16 and 19 were able to reduce the biofilm formation by approximately 30%. However, compound 23 did not demonstrate significant anti-biofilm activity and only inhibited pyocyanin production in P. aeruginosa. In conclusion, this study suggests that 1,3,4-oxadiazoles 15, 16, and 19 are the most promising compounds for future research as novel QS inhibitors against Gram-negative bacteria equipped with different QS signaling pathways.

A simple and sensitive liquid chromatography-tandem mass spectrometry (LC– MS/MS) method has been developed for the simultaneous determination of atorvastatin (ATOR), ezetimibe (EZM) and their three metabolites including o-hydroxyl atorvastatin (o-OH ATOR), p-hydroxyl atorvastatin (p-OH ATOR), and ezetimibe-glucuronide (EZM-G) in human plasma using benzyl paraben (BP) as internal standard (IS). The analytes and IS were ionized using ESI positive ion mode (ATOR, o-OH ATOR, and p-OH ATOR), ESI negative ion mode (EZM, EZM-G, and BP), and operated in multiple reaction monitoring (MRM) mode. They were next extracted by salting-out assisted liquid–liquid extraction with acetonitrile, and then analyzed by liquid chromatography on a reversed-phase chromatographic column (50 mm × 4.6 mm; 3.5 µm), using a mixture of ac-etonitrile and an acetic acid solution (0.5%) as the mobile phase, showing high extraction effi-ciency (>70%), and a minimized matrix effect. The method was satisfactorily validated, and showed excellent linearity over wide concentration ranges of 0.06–15 ng/mL, 0.6–150 ng/mL, 0.4–100 ng/mL, 0.12–30 ng/mL, and 0.05–3 ng/mL for EZM, EZM-G, ATOR, o-OH ATOR, and p-OH ATOR, respectively.

BackgroundIt is unclear what underpins the large global variations in the prevalence of fluoroquinolone resistance in gram-negative bacteria. We tested the hypothesis that different intensities in the use of quinolones for food-animals plays a role. MethodsWe used Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in human infections with Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa was correlated with the use of quinolones for food producing animals. Linear regression was used to assess the relative contributions of country-level quinolone consumption for food-animals and humans on fluoroquinolone resistance in these 4 species. ResultsThe prevalence of fluoroquinolone resistance in each species was positively associated with quinolone use for food-producing animals (E. coli [ρ=0.55; P<0.001], K. pneumoniae [ρ=0.58; P<0.001]; A. baumanii [ρ=0.54; P=0.004]; P. aeruginosa [ρ=0.48; P=0.008]). Linear regression revealed that both quinolone consumption in humans and food animals were independently associated with fluoroquinolone resistance in E. coli and A. baumanii. ConclusionsReducing quinolone use in food-producing animals may help retard the spread of fluoroquinolone resistance in various gram negative bacterial species.

In this paper, the notion of θ∗-weak contraction is introduced, which is utilized to prove some fixed point results. These results are helpful to give a positive response to certain open question raised by Kannan [Amer. Math. Monthly 76:1969] and Rhoades [Contemp. Math. 72:1988] on the existence of contractive definition which does not force the mapping to be continuous at the fixed point. Some illustrative examples are also given to support our results. As applications of our result, we investigate the existence and uniqueness of a solution of non-linear matrix equations and integral equations of Volterra type as well.

Different contact materials along with optimization of the deposition techniques expand the possibilities to obtain high performance room temperature CdTe-based X/γ-ray detectors. The heterostructures with ohmic (MoOx) and Schottky (MoOx, TiOx, TiN, and In) contacts, created by DC reactive magnetron sputtering and vacuum thermal evaporation, as well as In/CdTe/Au diodes with a p-n junction, formed by laser-induced doping, were developed and investigated. Depending on the pre-treatment of the surface of semi-insulating p-CdTe crystals, deposition of a MoOx film formed an ohmic or Schottky contact. Based on the calculations and IV characteristics of the fabricated Mo-MoOx/р-CdTe/MoOx-Mo, In/CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo Schottky-diode detectors, the current transport processes were described in the models of the carrier generation-recombination within the space-charge region (SCR) at low bias voltages, and space-charge limited current at higher voltages, respectively. The energies of generation–recombination centers, density of trapping centers, and carrier lifetimes were determined. A sharp increase in the reverse current in the Mo-MoOx/р-CdTe/MoOx-Mo, Ti-TiOx/р-CdTe/MoOx-Mo, and Ti-TiN/р-CdTe/MoOx-Mo heterostructures at high bias was discussed in frames of the Poole–Frenkel emission model. Nanosecond laser irradiation of the In electrode, pre-deposited on the p-CdTe crystals, resulted in an increase in the voltage range, corresponding to the carrier generation-recombination in the SCR, in the IV characteristics of the In/CdTe/Au diodes. Such In/CdTe/Au p-n junction diodes demonstrated high energy resolutions (7%@59.5 keV, 4%@122 keV, and 1.6%@662 keV).

Arabidopsis contains eight different h-type thioredoxins (Trx) being distributed in different cell organelles. Although Trx h2 is deemed to be localized in mitochondria, its subcellular localization and function remains a matter of debate. Here, Trx h2 localization and function were investigated using cell fractionation studies and reverse genetics. Differential centrifugation and immunodetection showed the Trx h2 protein to be distributed to the microsomal fraction rather than to mitochondrial preparations. To analyze whether Trx h2 has different roles than mitochondrial Trxs, Arabidopsis mutants lacking Trx h2 were compared with mutants deficient in mitochondrial Trx o1 and double mutants with joint deficiencies in both Trxs. Under constant medium light, trxh2 grew as the wild type, while trxo1 and trxo1h2 mutants showed impaired growth. This was accompanied by differences in the metabolite profiles. The trxo1 and trxo1h2 mutants clustered differently from the wild type during the night, revealing a decrease in ascorbate and glutathione redox states. In fluctuating light intensities, genotypic differences in growth rates were attenuated. Compared to the wild type, the fluctuating-light induced decrease in the NADPH/NADP ratio was diminished in the mutants, with the trxo1h2 double mutant showing the strongest effect. This was accompanied by an increase in the photosynthetic efficiency of the trxo1h2 mutant, specifically in the high light phases of fluctuating light. Conclusively, these results support the view that Trxs o1 and h2 are localized in different subcellular compartments, and have different effects on ascorbate and glutathione redox states and growth in medium light, but cooperatively affect NADP(H) redox state and photosynthetic efficiency in fluctuating light.

Transforming growth factor beta (TGF-β) is a determinant for inflammation and fibrosis in cardiac and skeletal muscle in Chagas disease. To determine its regulatory mechanisms, we investigated the response of T. cruzi-infected cardiomyocytes (CM), cardiac fibroblasts (CF) and L6E9 skeletal myoblasts to TGF-β. Cultures of CM, CF and L6E9 were infected with T. cruzi (Y strain) and treated with TGF-β (1–10 ng/mL, 1h or 48 h). Fibronectin (FN) distribution was analyzed by immunofluorescence and Western blot (WB). Phosphorylated SMAD2 (PS2), phospho-p38 (p-p38), and phospho-c-Jun (p-c-Jun) signaling were evaluated by WB. CF and L6E9 showed an increase in FN from 1 ng/mL of TGF-β, while CM displayed FN modulation only after 10 ng/mL treatment. CF and L6E9 showed higher PS2 levels than CM, while p38 is less stimulated in CF than CM and L6E9. After T. cruzi infection, localized FN disorganization was observed in infected CF and L6E9. T. cruzi induced an increase in FN in CF cultures, mainly in uninfected cells. Infected CF cultures treated with TGF-β showed a reduction in PS2 and an increase in p-p38 and p-c-Jun levels. Our data suggest that p38 and c-Jun pathways may be participating in the fibrosis regulatory process mediated by TGF-β after T. cruzi infection.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

In this paper, we study the p-adic integral representation on Z_p of q-Bernoulli numbers arising from two variable q-Bernstein polynomials and investigate some properties for the q-Bernoulli numbers. In addition, we give some new identities of q-Bernoulli numbers.

In the present paper, we introduce (p, q)-extension of Apostol type Frobenius-Euler polynomials and numbers and investigate some basic identities and properties for these polynomials and numbers, including addition theorems, difference equations, derivative properties, recurrence relations and so on. Then, we provide integral representations, explicit formulas and relations for these polynomials and numbers. Moreover, we discover (p, q)-extensions of Carlitz's result [L. Carlitz, Mat. Mag., 32 (1959), 247–260] and Srivastava and Pintér addition theorems in [H. M. Srivastava, A. Pinter, Appl. Math. Lett., 17 (2004), 375–380].

We propose a new hierarchy of the vector derivative nonlinear Schr{\"o}dinger equations and consider the simplest multiphase solutions of this hierarchy. The study of the simplest solutions of these equations led to the following results. First, the three-leaf spectral curves $\Gamma=\{(\mu,\lambda)\}$ of the simplest multiphase solutions have a quite simple symmetry. They are invariant with respect to holomorphic involution $\tau$. The type of this involution depends on the genus of the spectral curve. Or the involution has the form $\tau:(\mu,\lambda)\to(\mu,-\lambda)$, or $\tau:(\mu,\lambda)\to(-\mu,-\lambda)$. The presence of symmetry leads to the fact that the dynamics of the solution is determined not by the entire spectral curve $\Gamma$, but by its factor $\Gamma/\tau$, which has a smaller genus. Secondly, it turned out that the dynamics of the two-component vector $\bp=(p_1,p_2)^t$ is determined, first of all, by the dynamics of its length $\abs{\bp}$. Independent equations determine the dependence of the direction of the vector $\bp$ from its length. In cases where the direction of the vector $\bp$ is fixed, the corresponding spectral curve splits into separate components. In conclusion, we note that, as in the case of the Manakov system, the equation of the spectral curve is invariant with respect to the orthogonal transformation of the vector solutions. I.e., the solution can be found from the spectral curve up to the orthogonal transformation. This fact indicates that the spectral curve does not depend on the individual components of the solution, but on their symmetric functions. Thus, the spectral data of multiphase solutions have two symmetries. These symmetries make it difficult to reconstruct signals from their spectral data. The work contains examples illustrating these statements.

Spatial interpolation of meteorological data can have immense implications on risk management and climate change planning. Kriging with external drift (KED) is a spatial interpolation variant that uses auxiliary information in the estimation of target variable at unobserved locations. However, the traditional KED methods with linear trend functions may not be able to capture the complex and non-linear interdependence between target and auxiliary variables, which can lead to an inaccurate estimation. In this work, a novel KED method using least squares support vector regression (LSSVR) is proposed. This machine learning algorithm is employed to construct trend functions regardless of the type of variable interrelations being considered. To evaluate the efficiency of the proposed method (KED with LSSVR) relative to the traditional method (KED with a linear trend function), a systematic simulation study for estimating the monthly means temperature and pressure in Thailand in 2017 was conducted. The KED with LSSVR is shown to have superior performance over the KED with the linear trend function.

Leishmaniasis is one of the Neglected tropical diseases. Studies show that the poor knowledge about epidemiological aspects of Leishmaniasis within communities causes the collapse of existing disease control programs. Therefore, the present study focuses on a detailed survey of the existing awareness among the threatened population in the Medawachchiya PHI Area in the Anuradhapura District, Sri Lanka aiming to assist the health staff to organize community-based vector control programs effectively in the future. Assessment of the awareness of the two hundred and seventy households (n=270) residents from ten GNDs was carried out by using a structured questionnaire. Among 143 females and 134 males, only 75.1% have knowledge about the disease. 5.8%(n=16) of the participants know only about the vector and 28.9% (n=80) know their control methods. The study shows a shortage of a considerable amount of awareness about the disease among the studied population The study found that age and education levels had significant impacts on knowledge, attitudes, and practices. However, factors like gender, marital status, occupation, income, and expenses did not show significant correlations. The present study suggests the huge scope for community-related vector control methods for greater achievements in vector control methods by implementing a continuous educational program.

Weak contact metric structures on a smooth manifold, introduced by V. Rovenski and R. Wolak in 2022, have provided new insight into the theory of classical structures. In this paper, we define new structures of this kind (called weak nearly Sasakian and weak nearly cosymplectic and nearly K\"{a}hlerian structures) and study their geometry. We introduce weak nearly K\"{a}hlerian manifolds (generalizing nearly K\"{a}hlerian manifolds) and characterize weak nearly Sasakian and weak nearly cosymplectic hypersurfaces in such Riemannian manifolds.

A land cover map of two arctic catchments, nearby the Abisko Scientific Research Station, was obtained from a classification of a Sentinel-2 satellite image and a ground survey performed in July 2022. The two contiguous catchments, Miellajokka and Stordalen, are covered by various ecotypes, from boreal forest to alpine tundra and peatland. Two classification algorithms, support vector machine and random forest, were tested and gave very similar results. The percentage of correctly classified pixels was over 88% in both cases. The developed workflow relies solely on open source software and acquired ground observations. Space organization was directed by the altitude as demonstrated by the intersection of the land cover with the topography. Comparison between this new land cover map and previous ones based on data acquired between 2008 and 2011 shows some trends of vegetation cover evolution in response to climate change in the considered area. This land cover map is key input data for permafrost modeling, and hence for the quantification of climate change impacts in the studied area.

Vegetation classifications on large geographic scales are necessary to inform conservation decisions and monitor keystone, invasive, and endangered species. These classifications are often effectively achieved by applying models to imaging spectroscopy, a type of remote sensing, data, but such undertakings are often limited in spatial extent. Here we provide accurate, high-resolution spatial data on the keystone species Metrosideros polymorpha, a highly polymorphic tree species distributed across bioclimatic zones and environmental gradients on Hawai'i island, using airborne imaging spectroscopy and LiDAR. We compare two tree species classification techniques, support vector machine (SVM) and spectral mixture analysis (SMA), to assess their ability to map M. polymorpha over 28,000 square kilometers where differences in topography, background vegetation, sun angle relative to the aircraft, and day of data collection, among others, challenge accurate classification. To capture spatial variability in model performance, we applied gaussian process classification (GPC) to estimate the spatial probability density of M. polymorpha occurrence using only training sample locations. We found that, while SVM and SMA models exhibit similar raw score accuracy over the test set (96.0% and 93.4%, respectively), SVM better reproduces the spatial distribution of M. polymorpha than SMA. We developed a final 2 m x 2 m M. polymorpha presence dataset and a 30 m x 30 m M. polymorpha density dataset using SVM classifications that have been made publicly available for use in conservation applications. Accurate, large-scale species classifications are achievable, but metrics for model performance assessments must account for spatial variation of model accuracy.

During the last years, the increasing evidence of dietary antioxidant compounds and reducing chronic diseases and the relationship between diet and health have promoted an important innovation on the baked product sector, aiming at healthier formulations. This study aims to develop a tool based on mathematical models to predict baked goods total antioxidant capacity (TAC). The high variability of antioxidant properties of flours based on the aspects related to type of grains, varieties, proximal composition and processing, among others, makes very difficult to innovate on food product development without specific analysis. Using Total phenol content (TP), Oxygen radical absorbance capacity (ORAC) and Ferric reducing antioxidant power assay (FRAP) as proxies of antioxidant capacity. Three Bayesian-type models are proposed based on a double exponential parameterised curve that reflects the initial decrease and subsequent increase as a consequence of the observed processes of degradation and generation, respectively, of the antioxidant compounds. Once the values of the main parameters of each curve have been determined, support vector machines (SVR) with exponential kernel were used to predict, based on the temperature and duration of baking as well as the values of proteins and fibers of each native grain, the values of TAC during the baking time.

Building Information Modelling (BIM) has gained significant relevance in civil engineering, particularly in the infrastructure sector. It offers the potential to increase efficiencies, optimize processes, and enhance sustainability throughout infrastructure projects’ life cycles. BIM consolidates information about asset components into a single model, enabling real-time updates, cost reduction, and improved consistency. Digital twins serve as valuable extensions of BIM in infrastructure, playing a crucial role during operation. By capturing real-time data from sensors and IoT devices, digital twins enabls continuous monitoring, proactive maintenance, efficient energy management, and informed decision-making for optimized operational efficiency. Advancements in 3D point cloud technologies, such as 3D laser scanning, have expanded BIM’s application in operation and maintenance. These technologies rapidly capture accurate and detailed three-dimensional information, prompting the exploration of automated alternatives to manual point cloud modeling. This paper demonstrates the application of supervised machine learning, specifically support vector machines, for analyzing and segmenting 3D point clouds, a crucial step in 3D modeling. Various approaches for semantic segmentation are introduced, investigated, and evaluated using diverse data sets. The results highlight the effectiveness of supervised machine learning techniques in achieving accurate segmentation of 3D point clouds.

The increasing prevalence of depression worldwide requires more effectiveness in therapy approaches and a molecular understanding of antidepressants mode of action. We carried out untargeted metabolomics of the prefrontal cortex of rats exposed to chronic social isolation (CSIS), a rat model of depression, and/or fluoxetine treatment using liquid chromatography-high resolution mass spectrometry. The behavioral phenotype was assessed by the forced swim test. To analyze metabolomics data, univariate and multivariate analysis and biomarker capacity assessment using the classical receiver operating characteristic (ROC) curve were used. Support vector machine-linear kernel (SVM-LK), as a machine-learning algorithm was performed for binary classification. Upregulated myo-inositol following CSIS may represent a potential marker of depressive phenotype. Effective fluoxetine treatment reversed depressive-like behavior and increased sedoheptulose 7-phosphate, hypotaurine, and acetyl-L-carnitine contents, which were identified as potential markers. We identified 4 or 10 marker candidates with ROC curve greater than 0.9 for CSIS or fluoxetine effectiveness designation. SVM-LK has given accuracy of 61.50%, or 93.30%, and 7 or 25 predictive metabolites for CSIS vs. control and fluoxetine-treated CSIS vs. CSIS classification. Overall, metabolic fingerprints combined with ROC curve and SVM-LK may represent a new approach to identifying potential markers or predicting metabolites for group designation or classification.

In this study various samples were fabricated by increasing the amount of CNT from 0% to 5%. The bulk mechanical properties of the samples were measured using DMA. Alternatively, the local mechanical properties were assessed using nanoindentation technique. There is a clear trend that the behavior of the material is dependent of carbon fillers before, during and after percolation threshold. The bulk mechanical properties were reduced after the percolation threshold due to CNT agglomeration. Then the samples were exposed to acid solution for one week and one month. Regardless the amount of CNT in the matrix, there is always a gradient of properties from the skin to the core of the sample. There is a net reduction of in physical properties. However, the level of degradation was a dependent of the amount of CNT in the host polymer. At higher concentration the CNTs behave as a barrier. However due to the formation of porosity around the CNT agglomerates, the acid diffusion encounters preferential path ways. . Both techniques lead to the same observation..

Nowadays, there is extensive production and use of plastic materials for different industrial activities. These plastics, either from their primary production sources or through degradation processes of the plastics themselves, can contaminate the ecosystem with micro and nanoplastics. Once in the aquatic environment, these microplastics can be the basis for the adsorption of chemical pollutants, favoring that these chemical pollutants disperse more quickly in the environment and can affect living beings. Due to the lack of information on adsorption, three machine learning models (random forest, support vector machine, and artificial neural network) to predict different microplastic/water partition coefficients (log Kd) were developed using two different approximations (based on the number of input variables). The best-selected machine learning models present, in general, correlation coefficients upper than 0.92 in the query phase, which indicate that these type of models could be used for a rapid estimation of the absorption of organic contaminants on microplastics.

Newton’s law of universal gravitation applies between two point-masses. True gravitation of solid Earth is volume integration of gravitation of all point-masses inside the solid Earth on a point-mass in atmosphere. However, in meteorology the Earth “shrinks” into a point-mass located at Earth center with entire Earth mass to identify the Earth gravitation (untrue). Combination of untrue gravitational and centrifugal accelerations gives effective gravity (geff). Combination of true gravitational and centrifugal accelerations leads to true gravity (g). The true gravity g minus the effective gravity geff is the gravity disturbance vector, δg = g – geff. With the true gravity g used in the basic equations, seven non-dimensional numbers are proposed to identify the importance of δg versus traditional forcing terms such as horizontal pressure gradient force and Coriolis force. These non-dimensional numbers are calculated from two publicly available datasets with the geoid undulation (N) from the static gravity field model EIGEN-6C4 and long-term mean geopotential height (Z), wind velocity (u, v), and temperature (Ta) at 12 pressure levels in troposphere from the NCEP/NCAR reanalyzed climatology. The results demonstrate δg nonnegligible in hydrostatic equilibrium, geostrophic wind, geostrophic vorticity, Ekman pumping, Q vector, and Omega equation, but negligible in thermal wind relation.

Zika virus (ZIKV) is transmitted to humans by the infectious bite of mosquitoes like Aedes aegypti. After a viremic blood meal, the virus must infect the midgut, disseminate to tissues, and reach the salivary gland to be transmitted to a vertebrate host. Many factors influence the mosquito’s ability to become infected and transmit viruses, such as the mosquito’s genetic diversity, intrinsic antiviral barriers, and midgut microbiota. This study evaluated the patterns of ZIKV infection in Ae. aegypti field populations of a city. The infection rate, disseminated infection rate, viral transmission rate, and transmission efficiency were measured by quantitative PCR at 14 days post-infection. The results showed that all Ae. aegypti populations had individuals susceptible to ZIKV infection and able to transmit the virus. The infection parameters showed the city’s geographical area of origin of the Ae. aegypti influences their vector competence for ZIKV transmission.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

To achieve the near zero emission of wastewater in the flue gas desulfurization (FGD) system in coal-fired power plant and better utilize the exhaust heat from flue gas, a feasible technology of spraying FGD wastewater in the flue duct for evaporation is discussed in the present study. A full-scale influencing factor investigation on the wastewater droplet evaporation performance is established under the Eulerian-Lagrangian model numerically. The dominant factors, including the characters of wastewater droplets, flue gas and the spray nozzles were analyzed under different conditions, respectively. Considering the multiple factors and conditions in the process, a Least-Square support vector machine (LSSVM) model is introduced to predict the evaporation rate based on the numerical results. Conclusions are made that the flue gas temperature and droplet diameter are of great importance in the evaporation process. The spray direction of droplet parallel with the flue gas flow direction is profitable for the dispersion of droplet, resulting the maximal evaporation rate. A double-nozzle arrangement optimized with relatively small flow rate is recommended. The LSSVM model can accurately predict the evaporation rate using the numerical results with different conditions.

We describe a novel system for online prediction of lead seizures from long-term intracranial electroencephalogram (iEEG) recordings for canines with naturally occurring epilepsy. This study adopts new specification of lead seizures, reflecting strong clustering of seizures in observed data. This clustering results in fewer lead seizures (~7 lead seizures per dog), and hence new challenges for online seizure prediction, that are addressed in the proposed system. In particular, machine learning part of the system is implemented using the Group Learning method suitable for modeling sparse and noisy seizure data. In addition, several modifications for the proposed system are introduced to cope with non-stationarity of noisy iEEG signal. They include: (1) periodic re-training of SVM classifier using most recent training data; (2) removing samples with noisy labels from training data; (3) introducing new adaptive post-processing technique for combining many predictions made for 20-second windows into a single prediction for 4 hr segment. Application of the proposed system requires only 2 lead seizures for training the initial model, and results in high prediction performance for all four dogs (with mean 0.84 sensitivity, 0.27 time-in-warning, and 0.78 false-positive rate per day). Proposed system achieves accurate prediction of lead seizures during long-term test periods, 3–16 lead seizures during 169–364 days test period, whereas earlier studies did not differentiate between lead vs. non-lead seizures and used much shorter test periods (~few days long).

Fault diagnosis of the gearbox is a decisive part of the modern industry to find the many gearbox defects like gear tooth crack, chipped or broken, etc. But sometimes, the nonstationary properties of vibration signal and low energy of minimal faults make this procedure very challenging. Previously, many types of techniques have been developed for gearbox condition monitoring. But most of the methods are dealing with conventional techniques of the gearbox condition monitoring, such as time-domain analysis or frequency domain analysis. Most of the conventional methods are not suitable for the nonstationary vibration signal. Thus, this paper presents a novel gearbox fault diagnosis technique using conditional temporal moments and an optimizable support vector machine (SVM). This work also presents an integrated features extraction technique based on the standard features, i.e., statistical and spectral features with the combinations of moment features. The impact of the four conditional temporal moments of each gearbox condition is also presented. This work shows that the proposed method successfully classifies and categorizes the gearbox faults at an early stage.

The matrix converter converts the input line voltage into a variable voltage with an unrestricted output frequency without using an intermediate circuit, dc link circuit. A pure sine in and pure sine out is the unique feature of the matrix converter. This research paper also analyzes the basic operating principle and the simulation modeling of the direct matrix converter, which is controlled by the Space Vector Pulse Width Modulation technique by using the software which is known as MATLAB/Simulink. The most desirable features in the power frequency changes can be fulfilled by using the matrix converters, and this is the reason for the tremendous interest in the topology. Since the power electronic circuits which is known as the motor drives are used to operate the AC motors at the frequencies other than that of the supply.

We refute a recently proposed thought experiment namely the Dead-Alive Physicist (DAP) whose authors claim it to be the falsification of the von Neumann interpretation in Quantum Mechanics. We discover major flaws in their model and our justification serves the purpose of disregarding further claims and assertions made in the paper at various stages. Thus, in a yet another situation, it is proven that the formalism advanced by von Neumann is non-trivial and non-falsifiable.

As recent history has shown, changing climate not only threatens to increase the spread of known disease, but also the emergence of new and dangerous phenotypes. This occurred most recently with West Nile virus: a virus previously known for mild febrile illness rapidly emerged to become a major cause of mortality and long-term disability throughout the world. As we move forward, into increasingly uncertain times, public health research must begin to incorporate a broader understanding of the determinants of disease emergence – what, how, why, and when. The increasing mainstream availability of high-quality open data and high-powered analytical methods presents promising new opportunities. Up to now, quantitative models of disease outbreak risk have been largely based on just a few key drivers, namely climate and large-scale climatic effects. Such limited assessments, however, often overlook key interacting processes and downstream determinants more likely to drive local manifestation of disease. Such pivotal determinants may include local host abundance, human behavioral variability, and population susceptibility dynamics. The results of such analyses can therefore be misleading in cases where necessary downstream requirements are not fulfilled. It is therefore important to develop models that include climate and higher-level climatic effects alongside the downstream non-climatic factors that ultimately determine individual disease manifestation. Today, few models attempt to comprehensively address such dynamics: up until very recently, the technology simply hasn’t been available. Herein, we present an updated overview of current perspectives on the varying drivers and levels of interactions that drive disease spread. We review the predominant analytical paradigms, discuss their strengths and weaknesses, and highlight promising new analytical solutions. Our focus is on the prediction of arboviruses, particularly West Nile virus, as these diseases represent the pinnacle of epidemiological complexity – solution to which would serve as an effective “gatekeeper”. We present the current state-of-the-art with respect to known drivers of arbovirus outbreak risk and severity, differentially highlighting the impact of climate and non-climatic drivers. The reality of multiple classes of drivers interacting at different geospatial and temporal scales requires advanced new methodologies. We therefore close out by presenting and discussing some promising new applications of AI. Given the reality of accelerating disease risks due to climate change, public health and other related fields must begin the process of updating their research programs to incorporate these much needed, new capabilities.

The meshless Petrov-Galerkin (MLPG) method is developed to analyse 2-D problems for flexoelectricity and thermoelectricity. Both problems are multiphysical and scale dependent. The size-effect is considered by the strain- and electric field-gradients in the flexoelecricity and higher-grade heat flux in the thermoelectricity. The variational principle is applied to de-rive the governing equations considered constitutive equations. The order of derivatives in governing equations is higher than in equations obtained from classical theory. The coupled governing partial differential equations (PDE) are satisfied in a local weak-form on small fic-titious subdomains with a simple test function. Physical fields are approximated by the mov-ing least-squares (MLS) scheme. Applying the spatial approximations in local integral equa-tions a system of algebraic is obtained for the nodal unknowns.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Q_t-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Adequate knowledge about the development and operation of the components of water systems is of high importance in order to optimize them. For this reason, forecasting of future events becomes greatly significant due to making the appropriate decision. Moreover, operational river management severely depends on accurate and reliable flow forecasts. In this regard, current study inspects the accuracy of support vector regression (SVR), and SVR regulated with fruit fly optimization algorithm (FOASVR) and M5 model tree (M5), in river flow forecasting. Monthly data of river flow in two stations of the Lake Urmia Basin (Vaniar and Babarud stations on the Aji Chay and the Barandouz Rivers) were utilized in the current research. Additionally, the influence of periodicity (π) on the forecasting enactment was examined. To assess the performance of mentioned models, different statistical meters were implemented, including root mean squared error (RMSE), mean absolute error (MAE), correlation coefficient (R), and Bayesian information criterion (BIC). Results showed that the FOASVR with RMSE (4.36 and 6.33 m3/s), MAE (2.40 and 3.71 m3/s) and R (0.82 and 0.81) values had the best performances in forecasting river flows in Babarud and Vaniar stations, respectively. Also, regarding BIC parameters, Qt-1 and π were selected as parsimonious inputs for predicting river flow one month ahead. Overall findings indicated that, although both FOASVR and M5 predicted the river flows in suitable accordance with observed river flows, the performance of FOASVR was moderately better than the M5 and periodicity noticeably increased the performances of the models; consequently, FOASVR can be suggested as the accurate method for forecasting river flows.

Freeway travelling time is affected by many factors including traffic volume, adverse weather, accident, traffic control and so on. We employ the multiple source data-mining method to analyze freeway travelling time. We collected toll data, weather data, traffic accident disposal logs and other historical data of freeway G5513 in Hunan province, China. Using Support Vector Machine (SVM), we proposed the travelling time model based on these databases. The new SVM model can simulate the nonlinear relationship between travelling time and those factors. In order to improve the precision of the SVM model, we applied Artificial Fish Swarm algorithm to optimize the SVM model parameters, which include the kernel parameter σ, non-sensitive loss function parameter ε, and penalty parameter C. We compared the new optimized SVM model with Back Propagation (BP) neural network and common SVM model, using the historical data collected from freeway G5513. The results show that the accuracy of the optimized SVM model is 17.27% and 16.44% higher than those of the BP neural network model and the common SVM model respectively.

Inherent in every Active Magnetic Bearing (AMB) are differences between the expected geometric axes and the actual magnetic axes due to a combination of discrepancies, including physical variation from manufacturing tolerances and misalignment from mechanical assembly, fringing and leakage effects, as well as variations in magnetic material properties within a single AMB. A method is presented here for locating the magnetic axes of an AMB that will facilitate the accurate characterization of the bearing air gaps for potential improvement in field tuning, performance analyses and certain shaft force measurement techniques. This paper presents an extension of the application of the bias current perturbation method for the determination of the magnetic center [4] to the determination of magnetic axes for the further development of accurate current-based force measurement techniques [1].

The question of the relevance of human and natural capital, as well as the potential adverse effect of natural capital on economic growth, has gained increased attention in development economics. The aim of this paper is to theoretically and empirically assess the relevance of several forms of capital on economic growth in small economies that are dependent upon tourism or natural resources. The empirical framework is based on Impulse Response Functions obtained from Vector Autoregressive models in which we focus on the model where economic growth is the dependent variable for ten small economies that are dependent upon either tourism or natural resources. We find that there is evidence of the ‘’natural resource curse’’, especially in the economies that have a strong dependence on resources that are easily substitutable and whose prices constantly fluctuate. We further find that in the majority of observed cases the type of capital these small economies are most dependent on for their economic growth causes negative impulses in the majority of the observed periods. The main policy recommendation should be to assure that even these small economies should strive towards further diversification and avoid dependence on only one segment of their economy.

Photovoltaic materials convert light into electrical voltages. So far, most research in the field are focused on how to refine/improve the existing or standard photovoltaic cells to yield more efficient electricity, to reduce weight, to make more flexible shape, or to minimize costs under standard and uniform sunlight illuminations. In this project, we explore and demonstrate a hypothesis that non-uniform light illumination photovoltages can also be generated due to photo doping induced mobile charge carrier density gradient between light and dark areas in either p-type or n-type photo doping semiconductors. The term non-uniform light illumination was coined to refer to subjecting our photo sensing thin film devices to areas of high and low intensities of light illumination simultaneously, with an intention of creating a charge density gradient and therefore a voltage. Specifically, a polymeric composite thin film composed of P3HT (p-type photo doping semiconductor) and PCBM (photo doping electron acceptor and trap) at varying p-doping levels were studied. We observed that the fabricated photovoltaic cells with about 80% PCBM doped P3HT thin film devices exhibited 0.5-1.2 volts photovoltages under non-uniform light illuminations.

Background. ADHD is a neurodevelopmental disorder that is accompanied by executive deficits. Objectives. To obtain evidence of the usefulness of the BRIEF-P and to analyse the possible ceiling and floor effect of its scores in the assessment of executive function in preschoolers with signs compatible with a possible diagnosis of ADHD. Methods. Seven articles were selected from 2538 potentially eligible articles from different databases. We included studies assessing samples of individuals with symptoms compatible with ADHD, with age range 2-6 years, published in English or Spanish, during the period 2012-2022. References published in: Science Direct, NCBI (PubMed), ProQuest Education Journals in the last decade. Risk of bias was assessed using the QUADAS-2 questionnaire. The main variables were: age and executive functioning. Conclusions. Executive deficits in early-life individuals with ADHD-compatible symptoms are more extensive than deficits in working memory. BRIEF-P is an instrument that facilitates obtaining a sensitive and discriminative executive profile. It should be used in combination with other neuropsychological performance tests, finding a floor effect in tests associated with warm executive functions and a ceiling effect in cold executive functions. This requires using a variety of tests to assess executive performance in preschoolers with symptoms compatible with ADHD and designing intervention proposals in line with them...

Neuroinflammation is considered to be a significant component in a range of neuropathologies. Unfortunately, whilst its role is well recognized, the options for therapeutic intervention are limited. As such, there is a need to identify novel targets in order to increase treatment options. Given its role as both a neurotransmitter and an immune modulator, substance P and its NK1 receptor have been widely studied as a potential therapeutic target. There is evidence that NK1 receptor antagonists may exert beneficial effects in a range of conditions, including traumatic brain injury and stroke. Blocking the NK1 receptor has been shown to reduce blood-brain barrier dysfunction, reduce cerebral oedema, and reduce the levels of pro-inflammatory cytokines. These actions are associated with improved survival and functional outcomes. The NK1 receptor has also been shown to be involved in the inflammatory reaction to CNS infection, and hence antagonist may have some benefit in reducing infection-driven inflammation. However, the NK1 receptor may also play a role in the host immune response to infection, and so here, the potential beneficial and detrimental effects need to be carefully balanced. As such, the purpose of this review is to provide a summary of the involvement of substance P in acute inflammation, particularly in the context of traumatic brain injury and stroke.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

It is unclear how important it is to reduce fluoroquinolone consumption in the general population to prevent the spread of fluoroquinolone resistance in Neisseria gonorrhoeae (bystander selection). Methods We assessed bystander selection by using Spearman’s correlation to assess if the country-level prevalence of fluoroquinolone resistance in N. gonorrhoeae was correlated with the prevalence of fluoroquinolone resistance in four other gram-negative species - Acinetobacter baumannii, Escherichia coli, Klebsiella pneumoniae and Pseudomonas aeruginosa. Results Fluoroquinolone resistance in N. gonorrhoeae was positively associated with homologous resistance in all 4 species - A. baumanii. (ρ=0.61, P=0.0003, E. coli (ρ=0.67, P<0.0001), K. pneumoniae (ρ=0.52, P=0.0004) and P. aeruginosa (ρ=0.40, P=0.0206). Positive associations were also found between the national prevalence of fluoroquinolone resistance and fluoroquinolone consumption in the general population in the preceding year for 4 of the 5 species. Conclusions Gonococcal fluoroquinolone resistance can be productively viewed as being part of a syndemic of fluoroquinolone resistance. Strengthening antimicrobial stewardship programs may help retard the spread of fluoroquinolone resistance in N. gonorrhoeae.

Dendrobium okinawense is an endangered epiphytic orchid, and there has been no scientific report so far on its propagation. Protocorm is mass of cell, and protocorm-like bodies (PLBs) look alike protocorm produced by vegetative explants in vitro. Regeneration of PLBs is the most efficient technique for the orchids micro-propagation. We used different light emitting diodes (LEDs) for the efficient PLB organogenesis of D. okinawense. PLBs regenartion under green and red LED surpassed respectively 81.1% and 71.6% in numbers, and respectively 80.8% and 57.8% in fresh weight over white fluorescent light. We manipulated the culture media by different concentrations of PCIB and HMI. PLBs organogenesis promoted by low concentration, it increased respectively 35.9% and 19.3% over control by 0.01 mg/L PCIB and 0.01 ml/L HMI in numbers. Green LED and PCIB independently produced mostly similar numbers of new PLBs. Interestingly, culture media with 0.01 mg/L of PCIB further increased 8.5% of the numbers of PLBs under green LED, whereas the culture media with 0.01 mg/L HMI reduced the number of PLBs under green LED. PLBs culture under green LED with very low concentrations of PCIB manipulated culture media can significantly increase their organogenesis of D. okinawense.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

Deep learning has increasingly been employed to identify minerals. However, deep learning can only be used to identify minerals in the distribution of the training set, while any mineral outside the spectrum of the training set is inevitably categorized erroneously within a predetermined class from the training set. To solve this problem, the study introduces the approach that amalgamates One-Class Support Vector Machines (OCSVM) with the ResNet architecture for the out-of-distribution mineral detection. Initially, ResNet undergoes training using a training set comprising well-defined minerals. Subsequently, the earlier layers of the trained ResNet are employed to extract the discriminative features of the mineral under consideration. These extracted mineral features then become the input for OCSVM. When OCSVM discerns the mineral in the training set's distribution, it triggers the subsequent layers within the trained ResNet, facilitating the accurate classification of the mineral into one of the predefined categories encompassing the known minerals. In the event OCSVM identifies the mineral out of the training set's distribution, it is unequivocally categorized as an unclassified or 'unknown' mineral. Empirical results substantiate the method's capability to identify out-of-distribution minerals while concurrently maintaining a commendably high accuracy rate for the classification of the 36 in-distribution minerals.

Machine learning (ML) is enabling augmented reality (AR) to gain popularity in various fields, including gaming, entertainment, healthcare, and education. ML enhances AR applications in education by providing accurate visualizations of objects. For AR systems, ML algorithms facilitate the recognition of objects and gestures from kindergarten through university. The purpose of this survey is to provide an overview of various ways in which ML techniques can be applied within the field of AR within education. The first step is to describe the background of AR. In the next step, we will discuss the ML models that are used in AR education applications. Additionally, we discuss how ML is used in AR. Each subgroup’s challenges and solutions can be identified by analyzing these frameworks. In addition, we outline several research gaps and future research directions in ML-based AR frameworks for education.

Ensuring precise electric locomotive stopping is pivotal for achieving intelligent and unmanned auxiliary transportation systems. Currently, human drivers' expertise plays a central role in the stopping process, posing challenges for automation and cargo location accuracy, particularly in coal mining. This paper focuses on achieving accurate electric locomotive stopping under diverse conditions by utilizing permanent magnet synchronous motor-driven locomotives. This technique introduces a novel stopping control method that combines a fuzzy Proportional-Integral-Derivative (F-PID) controller and a vector control model for permanent magnet synchronous motors (PMSM). After this, we design the F-PID using the PMSM technique based on the new fuzzy rules for each sub-system. In the end, extensive simulations and real-world experiments are conducted on an electric locomotive stopping test bed, which demonstrate the effectiveness of the proposed control method. From the simulation results, it confirming that the ability to achieve precise stopping under various working conditions.

Seeds can maintain their quality for a limited time; after that, they will lose their germination ability and vigor. Some physiological and physicochemical changes in the structure of the seeds during storage can decrease the quality of the seeds which is known as aging. Therefore, detection of the strong young seeds from the old ones is a vital issue in the modern agriculture. Conventional methods of detection of the seed viability and germination are destructive, time-consuming and costly. In this research, two peanut cultivars, namely North Carolina 2 (NC-2) and Florispan were selected and three artificial aging levels were induced to them. Hyperspectral images (HSI) of the samples were acquired and the seed viability was evaluated using two pre-trained convolutional neural network (CNN) image processing models, AlexNet and VGGNet. The noise of the reflection spectra of the samples was relatively resolved and modified by combining Preprocessing techniques of moving average (MA) and standard normal variate (SNV). Using principal component analysis (PCA), the dimensions were declined and three principal components (PC) were extracted. These PCs were then used as variables in the classification of support vector machine (SVM) and linear discriminant analysis (LDA). The results showed the high capability of CNN architectures such as AlexNet and VGGNet in detection of the seed viability based on the HIS with no pre-processing and feature extraction. The mentioned architectures reached the accuracy of 0.985 and 0.986, respectively. The combination of feature extraction method of PCA with LDA and SVM classifiers showed that the use of a limited number of PCs instead of all wavelengths can decrease the complexity of modeling, while enhancing the efficiency of the models such that LDA and SVM classifiers achieved the accuracy of 0.983 and 0.986 in classification of peanut sees, respectively.

Text classification is one of the most important task in natural language processing, In this research, we carried out several experimental research on three (3) of the most popular Text classification NLP classifier in Convolutional Neural Network (CNN), Multinomial Naive Bayes (MNB), and Support Vector Machine (SVN). In the presence of enough training data, Deep Learning CNN works best in all parameters for evaluation with 77% accuracy, followed by SVM with accuracy of 76%, and multinomial Bayes with least performance of 69% accuracy. CNN has the best performance in the presence of large enough training dataset because of the presence of filter/ kernels which help to indentify patterns in text data regardless of their position in the sentence. We repeated the training again with just one-third of our data, at this point SVM comes with the best performance, the performance of CNN noticeably drops but still better than Multinomial Naive Bayes, the reason why SVM works best when we reduce the training data was because of its ability to look for a hyper-plane that creates a boundary between different classes of data so as to properly classify them, so we believed that getting the hyper-plane was more efficient when we reduce the dataset, hence reason for the good performance. Multinomial Naive Bayes have the least performance which we attributed to its assumption of independency between the features which sometimes does not hold true. We concluded that availability of data should be an important factor when choosing classifier for Natural Language Processing Text Classification task. CNN should be use in the presence of enough dataset, and SVM should be use when data is not enough. Multinomial Naive Bayes must not be trusted with state of the art NLP task due to its assumption of independency between the features.

This study provides a comprehensive assessment of Derawan Island's coral reefs over two decades (2003, 2011, and 2021) from a machine learning classification perspective. Employing non-parametric algorithms like Random Forest (RF), Support Vector Machine (SVM), and Classification and Regression Tree (CART), our analysis primarily focused on spatial and temporal changes in coral habitats. RF emerged as the most accurate method, demonstrating an accuracy of 71.43% with Landsat 9, 73.68% with Sentinel 2, and 78.28% with Multispectral Aerial Photos. We found that the accuracy of our classification results was significantly influenced by the geographic resolution, as well as the quality of field and satellite/aerial image data. Through spatial clustering, the coral habitats exhibited an Nearest Neighbor Index (NNI) value of 0.8727, indicating specific patterns of distribution. The analysis revealed a decrease in coral reef extent from 2003 to 2011, shrinking to 16 hectares with varying densities, followed by a slight area increase but with more heterogeneous densities between 2011 and 2021. This study not only highlights the dynamic nature of coral reef habitats over two decades but also underscores the critical role of machine learning in environmental monitoring and conservation efforts.

Persistent human papillomavirus (HPV) infection is responsible for practically all cervical and a high proportion of anogenital and oropharyngeal cancers. Therapeutic HPV vaccines in clinical development show great promise in improving outcomes for patients who mount an anti-HPV T cell response, but far from all patients elicit a sufficient immunological response. This witnesses a translational gap between animal models and human patients. Here, we investigated the potential of a new assay consisting of co-culturing vaccine-transduced dendritic cells (DCs) with syngeneic healthy human peripheral blood mononuclear cells (PBMCs) to mimic a human in vivo immunization. This new promising human ex vivo PBMC assay was evaluated using an innovative therapeutic adenovirus (Adv)-based HPV vaccine encoding the E1, E2, E6, and E7 HPV16 genes. This new method allowed us to show that vaccine-transduced DCs yielded functional effector T cells and unveiled information on immunohierarchy showing E1-specific T cell immunodominance over time. We suggest that this assay can be a valuable translational tool to complement the known animal models, not only for HPV therapeutic vaccines, and supports the use of E1 as an immunotherapeutic target. Nevertheless, the findings reported here need to be validated in a larger number of donors, and preferably in patient samples.

COVID-19, a contagious disease caused by the novel coronavirus SARS-CoV-2, emerged in 2019 and quickly became a pandemic, infecting more than 700 million people worldwide. The disease incidence, morbidity and mortality rates have started to decline since the development of effective vaccines against the virus and the widespread immunization of the population. SARS-CoV-2 vaccines are associated with minor local or systemic adverse reactions, while serious adverse effects are rare. Thyroid-related disorders have been reported after vaccination for COVID-19, and Graves’ disease (GD) is the second most common amongst them. Thyroid eye disease (TED), an extrathyroidal manifestation of GD is rarely observed post COVID-19 vaccination. All TED cases followed mRNA-based vaccinations, but two new onset mild TED cases post viral vector vaccine (ChAdox1nCoV-19) have also been reported. We report the case of a 63-year-old woman who presented with new onset hyperthyroidism and moderate-to-severe and active TED ten days after she received the first dose of a viral vector vaccine against SARS-CoV-2. This is the first case of moderate-to-severe TED after such a vaccine. Our patient was initially treated with intravenous glucocorticoids and subsequently with intravenous rituximab, due to no response. The disease was rendered inactive after rituximab, but constant diplopia persisted, and the patient was referred for rehabilitative surgery.

When implementing SVMs, two major problems are encountered: (a) the number of local minima increases exponentially with the number of samples and (b) the quantity of required computer storage, required for a regular quadratic programming solver, increases by an exponential mag-nitude as the problem size expands. The Kernel-Adatron family of algorithms gaining attention lately which has allowed it to handle very large classification and regression problems. Howev-er, these methods treat different types of samples (Noise, border, and core) in the same manner, which causes searches in unpromising areas and increases the number of iterations. In this work, we introduce a hybrid method to overcome these shortcomings, namely Optimal Recurrent Neu-ral Network Density Based Support Vector Machine (Opt-RNN-DBSVM). This method consists of four steps: (a) characterization of different samples, (b) elimination of samples with a low probability of being a support vector, (c) construction of an appropriate recurrent neural network based on an original energy function, and (d) solution of the system of differential equations, managing the dynamics of the RNN, using the Euler-Cauchy method involving an optimal time step. The RNN remembers the regions explored during the search process thanks to its recurrent architecture. We demonstrated that RNN-SVM converges to feasible support vectors and Opt-RNN-DBSVM has a very low time complexity compared to RNN-SVM with constant time step, and KAs-SVM. Several experiments were performed on academic data sets. We used several classification performances measures to compare Opt-RNN-DBSVM to different classification methods and the results obtained show the good performance of the proposed method.

Natural ecosystem of Islands and coastal region are vulnerable to climate change phenomena such as increasing temperature, fluctuating rainfalls, ocean acidification and tsunami. Andaman and Nicobar group of islands lies in Bay of Bangal facing such extreme climate phenomena. A spatial-temporal analysis of forest cover of middle Andaman region of the Andaman and Nicobar group of islands was done from 1990 to 2019 with an interval of 5-10 years. Support vector machine classifier, spectral indices such as Normalized Difference Vegetation Index, Normalized Difference Water Index, and Normalized Difference Built-up Index were used for the analysis of greenery, water resources, and urban land. Land surface temperature was estimated using split window algorithm for Landsat 8 and mono window algorithm for Landsat 5. The data showed relative contribution of forest region toward rising temperature in the island region. The research also showed that subsurface hydrology linked to interconnected lineaments provides a stable zone for forest cover. The open forest showed maximum fluctuation while minimum change was observed in Evergreen Forest. The spectral characteristics analysis using indices showed significant change except in 2005 due to Tsunami occurred in 2005. The land surface temperature showed fluctuation near to 30° C from 1990 to 2019.

To predict the remaining useful life (RUL) of proton exchange membrane fuel cell (PEMFC) in advance, a prediction method based on the voltage recovery model and Bayesian optimization of a multi-kernel relevance vector machine (MK-RVM) is proposed in this paper. First, the empirical mode decomposition (EMD) method was used to preprocess the data, and then the MK-RVM was used to train the model. Then, the Bayesian optimization algorithm was used to optimize the weight coefficient of the kernel function to complete the parameter update of the prediction model, and the voltage recovery model was added to the prediction model to realize the rapid and accurate prediction of the RUL of PEMFC. Finally, the method proposed in this paper was applied to the open data set of PEMFC provided by FCLAB, and the prediction accuracy of the RUL of PEMFC was obtained by 95.35%, which showed that the method had good gen-eralization ability and verified the accuracy of the prediction for the RUL of PEMFC.

In a limestone quarry mine, fragmentation is a crucial outcome of blasting operations. The optimization of blasting operations greatly benefits from the prediction of rock fragmentation. The main factors that affect fragmentation are rock mass characteristics, blast geometry, and explosive properties. This paper is a step towards the implementation of machine learning and deep learning algorithms for predicting the extent of fragmentation (in percentage) in opencast mining. Various parameters can affect fragmentation. But, in this paper initially, ten parameters (spacing, drill hole diameter, burden, average bench height, powder factor, number of holes, charge per delay, uniaxial compressive strength, specific drilling, and stemming) are collected to train the model. However, due to a weak correlation with rock fragmentation, drill diameter, Average bench height, compressive strength, stemming, and charge per delay are eliminated to reduce model complexity. A total of 219 data sets having five input features i.e., the number of holes, spacing, burden, specific drilling, and powder factor are used to develop the models. To predict rock fragmentation due to blasting in limestone quarry mines, both machine learning models (Random Forest Regression (Bagging), Support Vector Regression, and XG Boost Regression (Boosting)), as well as a deep learning model (Neural Network Regression), are applied to develop a model that can optimize the prediction of fragmentation. The Artificial neural network model optimization showed that the model with architecture 64-32-16-1 can perform well giving MSE (mean squared error) values of 41.32 and 28.59 on training and test data respectively. The R2 value for both training and test is 0.83. Random Forest regression is also performing well compared to SVR and XG boost with the MSE value 12.37 and 9.89 on training and testing data respectively. Here, the R2 value for both sets are 94%. Based on the permutation importance and Shapely plot values, the powder factor has the highest impact, and the burden has the lowest impact on fragmentation.

Pyrethroid resistance is widespread in malaria vectors. However, differential mortality in discriminating dose assays to different pyrethroids is often observed in wild populations. When this occurs, it is unclear if this differential mortality should be interpreted as an indication of differential levels of susceptibility within the pyrethroid class, and if so, if countries should consider selecting one specific pyrethroid for programmatic use over another. A review of evidence from molecular studies, resistance testing with laboratory colonies and wild populations, and mosquito behavioural assays was conducted to answer these questions. Evidence suggests that in areas where pyrethroid resistance exists, different results in insecticide susceptibility assays with specific pyrethroids currently in common use (deltamethrin, permethrin, α-cypermethrin and λ-cyhalothrin) are not necessarily indicative of an operationally relevant difference in potential performance. Consequently, it is not advisable to use rotation between these pyrethroids as an insecticide resistance management strategy. Less commonly used pyrethroids (bifenthrin and etofenprox) may have sufficiently different modes of action, though further work would be needed to examine how this may apply to insecticide resistance management.

Infection with Severe Acute Respiratory Syndrome coronavirus 2 (SARS-CoV-2) causes Coronavirus Disease 2019 (COVID-19), which has reached pandemic proportions. A number of effective vaccines have been produced, including mRNA vaccines and viral vector vaccines, which are now being implemented on a large scale in order to control the pandemic. The mRNA vaccines are composed of the Spike S1 protein encoding mRNA, incorporated in a lipid nanoparticle, stabilized by polyethylene glycol (PEG). mRNA vaccines are novel in many respects, including cellular uptake, the intracellular routing, processing, and secretion of the viral protein. Viral vector vaccines have incorporated DNA sequences encoding the SARS-CoV-2 Spike S1 protein into (attenuated) adenoviruses. The antigen presentation routes in MHC class I and class II, in relation to induction of virus neutralizing antibodies and cytotoxic T-lymphocytes will be reviewed. In rare cases, mRNA vaccines induce unwanted immune mediated side effects. mRNA based vaccines may lead to an anaphylactic reaction. This reaction may be triggered by PEG. The intracellular routing of PEG, and potential presentation in the context of CD1 will be discussed. Adenovirus vector based vaccines have been associated with thrombocytopenic thrombosis events. The anti-platelet factor 4 antibodies found in these patients could be generated due to conformational changes of relevant epitopes presented to the immune system.

Recent studies investigated the detectability of ship wake signatures on SAR imagery using a large number of SAR images collocated with Automatic Identification System data for training machine learning models. These detectability models are in agreement with oceanographic expectations from preceding studies and can therefore be used for comparing the performance of different SAR sensors in terms of wake detectability. Previous model comparisons showed better wake detection performance of TerraSAR-X (TS-X) than of RADARSAT-2 (RS2) and Sentinel-1 (S1). A comparison between CosmoSkymed (CSK) and RS2 is performed here, to examine the hypothesis that X-Band is generally better for wake detection than C-Band. Finally, this hypothesis is not confirmed, as the detectability models for TS-X, CSK and RS2 reveal similar performances. A comparison of wake detection performance should take the individual wake components into account separately.

With a mild Mediterranean-type climate, Corsica is endemic for canine vector-borne diseases (CVBDs) such as dirofilariosis (a mosquitoes borne-diseases: MBDs), leishmaniosis and ehrlichiosis. The aim of this present study was to evaluate a monthly multi-modal prophylactic strategy (MMP) against CVBDs occurring in Corsica. The study was conducted as a comparative field trial in which eighty dogs allocated into two groups were included: (i) Group 1 consisted of 25 dogs under the MMP [per-os administration of 1.5 tablet of milbemycine oxime-praziquantel and a topical line-on application of a 3.6 mL solution of dinotefuran-permethrin-pyriproxyfen] and (ii) Group 2 under various real-life prophylactic treatment (RLP) based on the use of ectoparasiticide products [different formulations: deltamethrin, fluralaner, fipronil] and/or macrocyclic lactones based-products [milbemycin oxime/praziquantel, milbemycin oxime, moxidectin] during the period ranging from June to October 2017. All animals were followed for one year and had blood drawn at day 0, followed by follow-up at 6 and 12 months. Samples were screened for filariosis using molecular tools as well as for leishmaniosis and ehrlichiosis using indirect immunofluorescence assay (IFA). At the end of the study, no new cases of CVBDs were recorded within Group 1. In Group 2, the cumulative incidence of CVBDs was 20.0% (n= 11; p= 0.015) including dirofilarioses due to Dirofilaria immitis and/or D. repens, with 16.4% (n= 9; p=0.027). Ehrlichiosis was 5.5% (n= 3; p=0.241). No new cases of leishmaniosis were detected in Group 2. The data illustrated that, unlike the RLP treatment which failed to protect at least 20% of dogs, the MMP based on the concurrent administration of milbemycine oxime-praziquantel and dinotefuran-permethrin-pyriproxyfen is efficient to protect dogs against CVBDs in a high-risk area.

Citrus greening disease or huanglongbing (HLB) caused by Candidatus Liberibacter asiaticus (CLas) limits the citrus production worldwide. CLas is transmitted by the Asian citrus psyllid (ACP), Diaphorina citri (Hemiptera: Psyllidae) in a persistent-propagative manner. Application of insecticides to manage the psyllid vectors and disease is the most common practice. Understanding the molecular interaction between CLas and ACP and interrupting the interrelationship can provide an alternative to insecticides for managing citrus greening disease. Transcriptome analysis of ACP in response to CLas showed differential expression of 3911 genes (2196 up-regulated, and 1715 down-regulated) including the key genes of ACP involved in cytoskeleton synthesis and nutrition-related proteins. Majority of the differentially expressed genes were categorized under molecular function followed by cellular components and biological processes. KEGG pathway analysis showed differential regulation of carbohydrate, nucleotide and energy metabolic pathways, the endocytotic pathway and the defense-related pathways. Differential regulation of genes associated with the key pathways might favors CLas to become systemic and propagate in its insect vector. The study provides an understanding of genes involved in circulation of CLas in ACP. The candidate genes involved in key physiological processes and CLas transmission by ACP would be potential targets for sustainable management of ACP and CLas.

Early detection of cancer increases the probability of recovery. This paper presents an intelligent decision support system (IDSS) for the early diagnosis of cancer based on gene expression profiles collected using DNA microarrays. Such datasets pose a challenge because of the small number of samples (no more than a few hundred) relative to the large number of genes (on the order of thousands). Therefore, a method of reducing the number of features (genes) that are not relevant to the disease of interest is necessary to avoid overfitting. The proposed methodology uses the information gain (IG) to select the most important features from the input patterns. Then, the selected features (genes) are reduced by applying the grey wolf optimization (GWO) algorithm. Finally, the methodology employs a support vector machine (SVM) classifier for cancer type classification. The proposed methodology was applied to two datasets (Breast and Colon) and was evaluated based on its classification accuracy, which is the most important performance measure in disease diagnosis. The experimental results indicate that the proposed methodology is able to enhance the stability of the classification accuracy as well as the feature selection

We developed a honey bee RNA-virus vector based on the genome of a picorna-like Deformed wing virus (DWV), the main viral pathogen of the honey bee (Apis mellifera). To test the potential of DWV to be utilized as a vector, the 717 nt sequence coding for the enhanced green fluorescent protein (eGFP), flanked by the peptides targeted by viral protease, was inserted into an infectious cDNA clone of DWV in-frame between the leader protein and the virus structural protein VP2 genes. The in vitro RNA transcripts from egfp-tagged DWV cDNA clones were infectious when injected into honey bee pupae. Stable DWV particles containing genomic RNA of the recovered DWV with egfp inserts were produced, as evidenced by cesium chloride density gradient centrifugation. These particles were infectious to honey bee pupae when injected intra-abdominally. Fluorescent microscopy showed GFP expression in the infected cells and Western blot analysis demonstrated accumulation of free eGFP rather than its fusions with DWV LP and/or VP2 proteins. Analysis of the progeny egfp-tagged DWV showed gradual accumulation of genome deletions for egfp, providing estimates for the rate of loss of a non-essential gene an insect RNA virus genome during natural infection.

The aim of this work was to investigate a new, simple one-pot combustion synthesis technique for creating sulphur-based CuS/ZnS p-n heterojunction nanocomposite photocatalysts. The study examined the photocatalytic activity and reusability of these nanocomposites in removing rhodamine B (RhB) dye under visible light irradiation. Various methods of characterisation were employed to determine the properties of the materials, including particle morphology, crystalline phases and bandgap energy. The intrinsic reaction parameters, such as catalyst loading, pH level of the solution, and initial pollutant concentration, were varied to establish the optimal photo-degradation conditions. The results showed that a binary CuS/ZnS catalyst with a 10 gL-1 loading, at pH 5, degraded 97% of 5 ppm RhB dye after 270 minutes of visible light irradiation. Addition-ally, this composite catalyst exhibited excellent chemical stability and reusability, achieving 83% RhB dye removal after five recycling runs. Scavenger tests identified the photogenerated holes (h+) and superoxide free radicals (•O2) as the primary reactive species responsible for degradation. This study provides valuable insight into the design of highly efficient nanomaterials for removing organopollutants in wastewater, and a possible reaction mechanism is proposed.

In many practical applications, it is more convenient to characterize the quality of production processes or service operations throughout the count of nonconformities. In the context of SPC, nonconformities are usually assumed to appear according to the binomial probability model. The conventional way for monitoring nonconformities involves Shewhart-type control procedures based on both constant and time-varying sample sizes. In this article, an EWMA scheme is proposed for monitoring the fraction of nonconforming items with time-varying sample sizes. The proposed control chart is referred to as the EWMAG-B and can be easily adapted to work with a constant sample size by fixing it at a needed value. By means of simulation, it was found out that the EWMAG-B chart outperforms the conventional p control chart in Phase II while detecting changes in the process level is wanted.

The thermoelectric generator (TEG) stands out in many energy harvesters due to its simple structure, small size, etc. However, previous studies rarely probe into the influence of TEG internal resistances on extracting maximum power from TEG, and tracking efficiency is limited. By analyzing the relationship between the tracking efficiency and the TEG internal resistances, a time exponential rate perturbation and observation (P&amp;O) technology is proposed to achieve maximum power point tracking (MPPT) for a wide resistance range of TEG. Using the time exponential rate P&amp;O, the MPPT circuit observes the power change by comparing PMOS on-time and perturbs the power by adjusting NMOS on-time exponentially. The MPPT circuit is implemented in a 110nm CMOS process. The tracking efficiency keeps a high level from 98.9 to 99.5%. The applicable range of the TEG resistance is from 1 to 12Ω, which is enhanced at least 2.2 times.

The cellular stress response corresponds to the molecular changes that cell undergoes in response to various environmental stimuli. It induces drastic changes in the regulation of gene expression, at transcriptional and post-transcriptional levels. Actually, translation is strongly affected with a blockade of the classical cap-dependent mechanism, whereas alternative mechanisms are activated to support translation of specific mRNAs. One of the major mechanisms involved in stress-activated translation is the internal ribosome entry site (IRES)-driven initiation. IRESs, first discovered in viral mRNAs, are present in cellular mRNAs coding for master regulators of cell responses, whose expression must be tightly controlled. IRESs allow translation of these mRNAs in response to different stresses, including DNA damage, amino-acid starvation, hypoxia or endoplasmic reticulum stress, as well as to physiological stimuli such as cell differentiation or synapse network formation. Importantly, cellular mRNA IRESs are regulated by IRES trans-acting factor (ITAFs), exerting their action by at least nine different mechanisms. This review presents an update of the reported ITAFs regulating cellular mRNA translation and of the different mechanisms allowing them to control translation initiation in specific conditions. The impact of ITAFs on coordinated expression of mRNA families and consequences in cell physiology and diseases are also highlighted.

Dengue, a perilous fever-type illness transmitted by mosquitoes, remains a significant global health concern. The incidence of dengue outbreaks is primarily influenced by climate factors, contributing to fluctuating dengue cases. Therefore, this study aims to develop predictive models for dengue outbreaks employing Machine Learning (ML) techniques. Four distinct ML models, namely K-Nearest Neighbor (KNN), Random Forest (RF), Gradient Boosting Regressor (GBR), and Support Vector Regressor (SVR), were employed in this study. Prior to model analysis, thorough data preprocessing was conducted. In some instances, certain attributes exhibiting sparse correlations with dengue occurrence were eliminated based on correlation analysis. Upon finalizing the models, performance evaluation was executed through comparison based on Mean Absolute Error (MAE) metrics. The findings of this comparative analysis revealed that the KNN model exhibited significantly superior performance compared to the other three models. This outcome underscores the potential of KNN in enhancing the accuracy of dengue outbreak predictions.

Transformation formula under the action of a general linear fractional transformation for generalized Dedekind eta-function has been a subject of intensive study, Rademacher, Dieter, Meyer et al. However, the (Hecke) modular relation structure has not been recognized until the work of Goldstein-de la Torre, and streamlining the classical proofs in the modular relation will reveal the meaning hidden in those works. Our main aim is to elucidate the works of these researchers in the context of modular relations.

We investigated the prevalence and genetic diversity of Wolbachia pipientis strains in Aedes albopictus populations in Greece. Using a combination of PCR and Sanger sequencing techniques, we genotyped Wolbachia strains in 105 mosquitoes collected across eight different prefectures in 2021. We found a high prevalence of Wolbachia in both male (90%) and female (97%) mosquitoes. Among the infected samples, 84% had double infections with both wAlbA and wAlbB strains, while 16% had infections with only wAlbB. Our comparison of the Multi-Locus Sequence Typing (MLST) profile, employing gatB-coxA-hcpA-ftsZ-fbpA genotyping, revealed a single MLST profile for each wAlbA and wAlbB strain in Greek populations. The same MLST profiles were also reported in populations from China, Russia, and Argentina, suggesting low levels of global diversity in wAlbA and wAlbB strains. Furthermore, our results indicated a significant association between temperature and the prevalence of single infections (P = 6.498E-07), with higher temperatures correlating with an increased likelihood of single infections. Although male-bias showed a tendency towards single infections, the effect was marginally non-significant (P = 0.053). These results were confirmed using a bootstrap-with-replacement analysis approach. Overall, our findings offer novel insights into the distribution and species diversity of Wolbachia strains in Greek Ae. albopictus populations, emphasizing the importance of understanding the short-term plastic and adaptive responses of these organisms to environmental stressors and rapid climate change.

This work studies the discontinuities features of sedimentary flysch materials in a 100 km2 area belonging to the Basque Arc. Such materials are common in this Spanish Alpine region located in the north of the Iberian Peninsula. A total of 33 outcrops are investigated by an intensive geotechnical investigation including geomechanical stations, boreholes and mechanical laboratory tests. Two flysch units are characterized: the Upper Aguinaga Formation or siliciclastic flysch, and the Lower Itziar Formation or calcareous flysch. Differences between both flysch formation are found. Joints in the siliciclastic flysch formation present an undulated roughness, with a spacing narrower and a persistence lower than in the calcareous flysch formation, which exhibits higher friction angles, although roughness is essentially planar. In addition, the potential of using Artificial Intelligence (AI) techniques, particularly Artificial Neural Networks and Support Vector Machine, to estimate the Geological Strength Index (GSI) from the Rock Quality Design (RQD) and some discontinuities features (spacing, persistence, aperture and roughness) is investigated. AI techniques are found to be satisfactory, being the Support Vector Machine with a linear kernel the technique which achieves the best performance.

India ranks among the top ten nations in the world for grape production. Fungal pathogens inflict damage to crop plants in turn making cultivators bear huge economical losses. With an output of 1.21 million tons (about 2% of 57.40 million tons produced globally). 1.2% of the nation’s total fruit cropland is covered by grapes. But due to fungal diseases the effect of the yield produced ranges from 5-80% depending on the severity of diseases which will affect the yield of grape vineyard. In precision agriculture, new sensing technologies and artificial intelligence could be used to automatically identify grapevine and disease pest symptoms. Traditional manual disease-monitoring methods are inefficient, labor-intensive, and ineffective. Timely effective and precise evaluation of grape diseases is admitted as a critical step in the field management. In this paper, we are explaining about different optical sensing methods applied for RGB, Multispectral and Thermal cameras. Section-wise we will be describing environmental set up for image-aquation, data-preprocessing, different modelling methods, evaluation matrix, result, and reviewer’s comment.

Pseudo-nitzschia spp. blooms are a recurrent problem in many coastal areas globally imposing some significant threats to the health of human, ecosystems and economy. Monitoring programmes have been established, where feasible, to mitigate the impacts caused by Pseudo-nitzschia spp. and other harmful algae blooms. The detection of such blooms from satellite data could really provide timely information on emerging risks but the development of taxa-specific algorithms from available multispectral data is still challenged by coupled optical properties with other taxa and water constituents, availability of ground data and generalisation capabilities of algorithms. Here, we developed a new set of algorithms (PNOI) for the detection and monitoring of Pseudo-nitzschia spp. blooms over the Galician coast (NW Iberian Peninsula) from Sentinel-3 OLCI reflectances using support vector machine (SVM). Our algorithm was trained and tested with reflectance data from 260 OLCI images and 4607 Pseudo-nitzschia spp. match up data points, of which 2171 were of high quality. The performance of no bloom/bloom model in the independent test set was robust, showing values of 0.80, 0.72 and 0.79 for area under the curve (AUC), sensitivity and specificity, respectively. Similar results were obtained by our below detection limit/presence model. We also present different model thresholds based on optimisation of true skill statistic (TSS) and F1-score. PNOI outperforms linear models, while its relationship with in-situ chlorophyll-a concentrations is weak demonstrating poor correlation with the phytoplankton abundance. We showcase the importance of PNOI algorithm and OLCI sensor for monitoring the bloom evolution between the weekly ground sampling and during periods of ground data absence, such as due to Covid-19.

Underwater acoustic sensor network (UASN) plays a crucial role in collecting real-time data from remote areas of the ocean. However, deploying the UASN is a challenging problem due to the harsh environment and high deployment cost. Therefore, it is essential to design an appropriate routing protocol to effectively address the issues of routing void, packet delivery delay, and energy utilization. In this paper, an adaptive support-vector-machine-based routing (ASVMR) protocol is proposed for the UASN to prolong the network lifetime and reduce the end-to-end packet delivery delay. The proposed protocol employs a distributed routing approach that dynamically optimizes the routing path in real-time by considering four types of node state information. Moreover, the ASVMR protocol establishes a "routing vector" spanning from the current node to the sink node, and selects a suitable pipe radius according to the packet delivery ratio (PDR). In addition, the ASVMR protocol incorporates future states of sensor nodes into the decision-making process, along with the adoption of a waiting time mechanism and routing void recovery mechanism. Extensive simulation results demonstrate that the proposed ASVMR protocol performs well, in terms of the PDR, the hop count, the end-to-end delay, and the energy efficiency in dynamic underwater environments.

Heartland virus (HRTV) is an emerging tick-borne bandavirus that is capable of causing severe disease characterized by acute thrombocytopenia and lymphopenia. The virus is endemic to the eastern United States, and is carried by the Lone Star tick (Amblyomma americanum). Since its discovery in 2009, at least 60 human infections have been recorded across this area, with an overall 5-10\% estimated mortality rate. All infections reported thus far have occurred following a known tick bite or exposure to tick-infested areas, but the possibility of nosocomial transmission has not been ruled out. Despite relatively high rates of seroprevalence among certain wildlife species such as white-tailed deer, the reservoir species for HRTV remains unknown, as the virus has never been isolated from any mammalian wildlife species. Furthermore, how the virus is transmitted to its vector species in nature remains unknown, though laboratory studies have confirmed both horizontal and vertical transmission of HRTV in A. americanum. In addition, the recent 2017 introduction of the Asian longhorned tick (Haemaphysalis longicornis) to the US has raised concerns about possible spillover of HRTV into a new tick species that has been confirmed to be a competent vector for HRTV in the laboratory. Thus, an increased awareness of its clinical presentation is needed, and further research is urgently required to establish the natural transmission cycle and develop new countermeasures for this novel zoonotic pathogen

To address the problem of limited fault diagnosis accuracy in oil-immersed on-load tap changers (OLTC), this paper introduces a novel fault diagnosis method that combines the analysis of mechanical vibration signals and high-frequency current signals. The proposed approach aims to enhance the accuracy of fault diagnosis. To begin, an experimental platform is constructed to simulate the OLTC contact. Mechanical vibration signals and high-frequency current signals are collected from the testing platform under various operating states. These signals are then subjected to wavelet packet transform for denoising, followed by correlation analysis to capture the relationship between signals in different states. Based on these preliminary steps, the features of the signals are extracted and analyzed using ensemble empirical mode decomposition and the Hilbert-Huang transform. Subsequently, a support vector machine (SVM) is employed to analyze both the mechanical vibration signal and high-frequency current signal, enabling the classification of the OLTC contact state. The results demonstrate that the combination of characteristic analysis of mechanical vibration signals and high-frequency current signals provides a more comprehensive reflection of the actual OLTC contact state under different conditions. Through the SVM classification, the error between the predicted values and real values of the two types of signals remains below 10%, validating the efficiency and feasibility of the proposed method for fault diagnosis of OLTC contacts. These research findings serve as a reliable foundation for the diagnosis of operational states of on-site oil-immersed on-load tap changers, offering valuable insights for practical applications.

Coal is an important resource that is closely related to people’s lives and has an irreplaceable role. However, coal mine safety accidents occur from time to time in the process of working underground. To this end, this paper proposes a coal mine environmental safety early warning model to detect abnormalities and ensure worker safety in a timely manner by assessing the underground climate environment. In this paper, the support vector machine (SVM) parameters are optimized using an improved artificial hummingbird algorithm (IAHA), and its safety level is classified by combining various environmental parameters. To address the problems of insufficient global exploration capability and slow convergence of the artificial hummingbird algorithm during iterations, a strategy incorporating Tent chaos mapping and backward learning is used to initialize the population, a Levy flight strategy is introduced to improve the search capability during the guided foraging phase, and then the simplex method is introduced to replace the worst value before the end of each iteration of the algorithm. The IAHA-SVM safety warning model was established using the improved algorithm to classify and predict the safety of the coal mine environment into four classes. Finally, the performance of the IAHA algorithm and the IAHA-SVM model are simulated separately. The simulation results show that the convergence speed and the search accuracy of the IAHA algorithm are improved, and the performance of the IAHA-SVM model has a significant improvement.

The study uses annual time series data from the South Africa Reverse Bank (SARB) from 1980 to 2020 to examine the effectiveness of fiscal policy on economic growth in South Africa. The Augmented Dickey-Fuller (ADF) and Phillips-Perron (PP) unit root tests, as well as the Johansen Co-integration test, Granger causality test, and Vector Auto-Regression (VAR) method, were used in the study. Real GDP per capita (RGDP) is used as proxy of economic growth and gross fixed capital formation (GFCF), government expenditure (GEXP) and government deficit (GOVD) as the proxies of fiscal policy. The ADF test results show that all variables are stationary at the first difference, with the exception of GFCF and GEXP, which are stationary at I(0), whereas the PP test results show that all variables are stationary at I(1), with the exception of GEXP, which is stationary at I(0). At Maximum Eigenvalue, the four variables are not cointegrated. The findings of the Granger causality test demonstrated a unidirectional causation from GOVD to RGDP, as well as a bidirectional causality from RGDP to GFCF and GEXP. Error Correction Model Estimated using VAR shows that GFCF, GEXP have positive effect on RGDP whereas GOVD has a negative effect on RGDP in the short run. The findings also presented that the VAR's residuals are homoscedastic, which means they are normally distributed and have no serial correlation.

We analyze the modular geometry of the variable exponent Lebesgue space L^p(.). We show that L^p(.) possesses a modular uniform convexity property. Part of the novelty is that the property holds even in the case supp(x) = ∞ . We present specific applications to fixed point theory. xÆΩ

Often, in biology, we are faced with the problem of exploring relevant unknown biological hypotheses in the form of myriads of combination of factors that might be affecting the pathway under certain conditions. Currently, a major persisting problem is to cherry pick the combinations based on expert advice, literature survey or guesses for investigation. This entails investment in time, energy and expenses at various levels of research. To address these issues, a search engine design was recently been developed, which showed promise by revealing existing confirmatory published wet lab results. Additionally and of import, the engine mined up a range of unexplored/untested/unknown combinations of genetic factors in the Wnt pathway that were affected by ETC-1922159 enantiomer, a PORCN-WNT inhibitor, after the colorectal cancer cells were treated with the inhibitor drug. As an example, MYC is known to upregulate PRC2 complex. PRC2 complex contains EZH2, which suppresses tumor suppressor genes via epigenetic modifications. MYC and HOXB8 are up regulated in colorectal cancer, however, the dual working mechanism of the same is not known. The in silico engine showed positioning which correctly approximates and assigns to this 3rd order combination of MYC-HOXB8-EZH2, pointing to the in vitro/in vivo down regulation by ETC-1922159. If the protein interaction of MYC-HOXB8 can be established and a study be done apropos EZH2, it will establish at in vitro/in vivo level, the in silico ranking also. The potential of this engine is immense given the problem faced in biology and other fields. Here we elucidate the R code to understand the mechanics of the search engine in a fluid manner for systems biologists. Though the search engine is in the developmental stage, we share the detailed mechanism of the working principles of the same as it can be generalized to problems in other fields.

We introduce a modelling framework for the investigation of on-line machine learning processes in non-stationary environments. We exemplify the approach in terms of two specific model situations: In the first, we consider the learning of a classification scheme from clustered data by means of prototype-based Learning Vector Quantization (LVQ). In the second, we study the training of layered neural networks with sigmoidal activations for the purpose of regression. In both cases, the target, i.e. the classification or regression scheme, is considered to change continuously while the system is trained from a stream of labeled data. We extend and apply methods borrowed from statistical physics which have been used frequently for the exact description of training dynamics in stationary environments. Extensions of the approach allow for the computation of typical learning curves in the presence of concept drift in a variety of model situations. First results are presented and discussed for stochastic drift processes in classification and regression problems. They indicate that LVQ is capable of tracking a classification scheme under drift to a non-trivial extent. Furthermore, we show that concept drift can cause the persistence of sub-optimal plateau states in gradient based training of layered neural networks for regression.

Since general relativity (GR) has already established that matter can simultaneously have two different values of mass depending on its context, we argue that the missing mass attributed to non-baryonic dark matter (DM) actually obtains because there are two different values of mass for the baryonic matter involved. The globally obtained "dynamical mass'' of baryonic matter can be understood as a small perturbation to a background spacetime metric even though it's much larger than the locally obtained "proper mass". Having successfully fit the SCP Union2.1 SN Ia data without accelerating expansion or a cosmological constant, we employ the same ansatz to compute dynamical mass from proper mass and explain galactic rotation curves (THINGS data), the mass profiles of X-ray clusters (ROSAT and ASCA data) and the angular power spectrum of the cosmic microwave background (Planck 2015 data) without DM. We compare our fits to modified Newtonian dynamics (MOND), metric skew-tensor gravity (MSTG) and scalar-tensor-vector gravity (STVG) for each data set, respectively, since these modified gravity programs are known to generate good fits to these data. Overall, we find our fits to be comparable to those of MOND, MSTG and STVG. While this favorable comparison does not establish the validity of our proposition, it does provide confidence in using the fits to pursue an underlying action. Indeed, the functional form of our ansatz reveals an interesting structure in these fits.

Supervised land-use/land-cover (LULC) classifications are typically conducted using class assignment rules derived from a set of multiclass training samples. Consequently, classification accuracy varies with the training data set and is thus associated with uncertainty. In this study, we propose a bootstrap resampling and reclassification approach that can be applied for assessing not only the uncertainty in classification results of the bootstrap-training data sets, but also the classification uncertainty of individual pixels in the study area. Two measures of pixel-specific classification uncertainty, namely the maximum class probability and Shannon entropy, were derived from the class probability vector of individual pixels and used for the identification of unclassified pixels. Unclassified pixels that are identified using the traditional chi-square threshold technique represent outliers of individual LULC classes, but they are not necessarily associated with higher classification uncertainty. By contrast, unclassified pixels identified using the equal-likelihood technique are associated with higher classification uncertainty and they mostly occur on or near the borders of different land-cover.

To improve the understanding of soil–pile interaction of laterally loaded piles, the quasi-static test of pile group foundation in silty clay with 5 foundation piles arranged in cross shape is carried out. The direct measurement-based p–y curves at different depths showed nonlinear behavior, in which the initial stiffness and ultimate soil reaction increased as the depth increased. The loading displacement amplitude corresponding to the failure of each foundation pile in the high axial compression reinforced concrete pile group foundation is given as follows: the front-end nappe foundation pile (#3 pile) is 6mm, the middle pile is 16mm, the front-end nappe foundation pile is 20mm, and the loading displacement amplitude of side pile is 24mm. In silty clay, due to the existence of pile group effect, the edge effect has little effect on the horizontal foundation bed coefficient of foundation pile in pile group, while the influence of masking effect on the horizontal foundation bed coefficient of each foundation pile in pile group is not related to the position of pile, but only to the existence of masking effect, and the influence of different columns of masking effect on the horizontal foundation bed coefficient is the same.