The removal of chromium(VI) from acidic (HCl) medium through non-dispersive extraction with strip dispersion (NDXSD) was investigated using a microporous PVDF membrane support in a permeation cell. The ionic liquid Cyphos IL102 (phosphonium salt) in Solvesso 100 was used as organic phase. In NDXSD the stripping phase (NaOH) is dispersed in the organic phase in the cell side with an impeller stirrer adequate to form a strip dispersion. This pseudo-emulsion phase (organic + strip solutions) provides a constant supply of the Cyphos IL102/Solvesso 100 to the membrane phase. Various hydrodynamic and chemical parameters, such as variation in the feed and pseudo-emulsion stirring speeds, HCl and Cr(VI) concentrations in the feed phase, and carrier concentration, were investigated. From the experimental data, several mass transfer coefficients were estimated, as well as it was investigated the performance of the present system against other ionic liquids and the presence of base metals in the feed phase.

In this study, we aim to evaluate how cyclodextrin molecules affect the hydrophilicity and selec-tivity of PVDF membrane. Herein, we prepared PVDF-PVP(1-x) β-CDx membranes, with x rang-ing from 0 to 1 wt%. The membranes were deeply characterized by means of X-ray diffraction (XRD), attenuated total reflectance infrared (ATR-IR), Raman spectroscopies, Thermal gravimet-ric analysis (TGA), Contact angle measurement (CA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The study unequivocally demonstrates the effectiveness of the addition of β-CD molecules on membranes' structural, morphological, and dielectric properties. Adding 0.25wt% β-CD enhanced hydrophilicity, with CA decreasing from 72.6° to 56° and roughness decreasing from 81 to 29 nm. The PVDF-PVP(1-x) β-CDx membranes were then fully characterized using electrochemical impedance spectroscopy (EIS) to determine their dielectric properties, which clearly showed that the presence of β-CD induced polarization of the mem-brane. The separation of various dyes with different sizes and charges was utilized. These dyes included methylene blue (MB, positive, 0.504 nm), methyl red (MR, neutral, 0.487 nm), rose Bengal (RB, negative, 0.588 nm), and brilliant blue (BB, negative, 0.798 nm). Based on our re-search, we found that the membrane's selectivity is determined by both exclusion factors (such as size and dielectric properties) and inclusion inside the β-CD cage. We found that using alpha-CD instead of beta-CD led to the disappearance of dye inclusion. These findings strongly sug-gest that β-CD molecules can be a viable solution for dye removal from wastewater.

Chronic kidney disease (CKD) is characterized by a continuous decline in kidney function, often persisting for years or even a lifetime. This study presents a new exploration into the extraction and application of insect chitosan (Tenebrio molitor) targeting hemodialysis (HD). Initially, the potential of insect-derived chitosan as a sustainable and effective alternative to traditional sources (i.e. crustaceans) is demonstrated. Efficient extraction methods were developed (totaling between 6 h and 12 h), producing chitosan. Firstly, chitin was efficiently isolated from T. molitor through deproteinization and demineralization, with yields of approximately 5% (w/w). Subsequently, chitosan was obtained from the extracted chitin resulting in yields of between 65.0 ± 0.8% (w/w) and 79.3 ± 0.8% (w/w). Characterization using Fourier Transform Infrared Spectroscopy (FTIR) confirmed structural similarities with commercial chitosan and degrees of deacetylation in the 73 - 75% range. The bioactive properties of chitosan obtained from T. molitor, including antimicrobial and antioxidant activities, were evaluated. All the microorganisms tested were inhibited, exhibiting minimum lethal concentrations between 2 and 8 mg/mL, confirming the antimicrobial activity of the extracted chitosan. In addition, chitosan showed antioxidant activity in the range of 60 to 65 µmol Trolox equivalent/g, suggesting its viability for various medical applications.This study also developed a chitosan-based membrane (CH - M) culminating in a proof-of-concept phase for hemodialysis. The permeation characteristics of CH-M for urea and albumin were studied in vitro to assess their suitability as HD membranes. Urea was permeable to values of over 70% and albumin was retained.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

This research aimed to synthesize Polyvinyl fluoride (PVDF) membranes and coat them with Tannic acid (TA) nanoparticles and Polyethylene glycol (PEG) additives so that the membrane's removal efficacy for humic acid (HA) pollutant from agricultural wastewater was investigated. Thus, six membranes with PEG:TA ratios of 0:0, 1:0, 0:1, 1:1, 4:1 and 1:4 were synthesized. Then the membranes' characteristics were identified by FT-IR ATR, FESEM, and AFM analysis, and HA's particle size and zeta potential were also investigated. Based on optimizing effective parameters, the operating pressure of 1.5 bar and HA concentration of 80 ppm were selected as optimal values. The membrane with PEG:TA=4:1, as the optimally modified membrane, had a pure water flux of 446.03 L/m2.h, effluent flux of 72.43 L/m2.h and pollutant removal rate of 86.62% at pH=7 After 60 min had passed. These values for the pristine membrane (PEG:TA=0:0) were 265.64 L/m2.h, 89.39 L/m2.h, and 75.59%, respectively. The results showed that although the effluent flux was lower in the optimized modified membrane than in the pristine membrane, HA removal percentage was increased.

Antibodies are important tools for the study of membrane proteins in biological, biophysics and structural analyses. However, the production of purified membrane proteins is still a formidable challenge due to the amphipathic character and inherent instability of these proteins. In this work, we tested a strategy for producing antibodies against an ATP-Binding Cassette (ABC) transporter without the need to produce the full membrane complex. Instead, just the extra cytoplasmic regions of the ABC-type transporter Rv1819c from Mycobacterium tuberculosis were presented in the RAD-display, a scaffold system based on the engineered Pyrococcus furiosus RadA protein developed for exposition of peptides. The RadA scaffold protein is highly stable, can tolerate long insertions and easy to produce in Escherichia coli. Based on the three-dimensional structure of Rv1891c, we selected two versions of the main extracellular loops of the permease to use as test cases for this approach. Rv1819c-derived peptides displayed on RAD display system were used for immunization of mice and production of polyclonal antibodies. These antibodies were able to recognize the transporter in M. tuberculosis cell extracts, on intact cells by flow cytometry and as purified protein. The results showed the approach can be a useful tool for in vitro analyses, screening, and evaluation of different epitopes in membrane proteins.

The vagina is an essential component of the female reproductive system and is responsible for providing female sexual satisfaction. Vaginal smooth muscle contraction plays a crucial role in various physiological processes, including sexual arousal, childbirth, and urinary continence. In pathophysiological conditions such as pelvic floor disorders, aberrations in vaginal smooth muscle function can lead to urinary incontinence and pelvic organ prolapse. A set of cellular and sub-cellular physiological mechanisms regulates the contractile properties of the vaginal smooth muscle cells. Calcium influx is a crucial determinant of smooth muscle contraction, facilitated through voltage-dependent calcium channels and calcium release from intracellular stores. Comprehensive reviews on smooth muscle biophysics are relatively scarce within the scientific literature, likely due to the complexity and specialized nature of the topic. The objective of this review is to provide a comprehensive description of alterations in the cellular physiology of vaginal smooth muscle contraction. The benefit associated with this particular approach is that conducting a comprehensive examination of the cellular mechanisms underlying contractile activation will enable the creation of more targeted therapeutic agents to control vaginal contraction disorders.

Hepatocellular carcinoma (HCC) is a heterogeneous malignancy with complex carcinogenesis. Although there has been significant progress in the treatment of HCC over the past decades, drug resistance to chemotherapy remains a major obstacle in its successful management. In this study we were able to reduce chemoresistance in cisplatin-resistant HepG2 cells by either silencing the expression of transglutaminase type 2 (TG2) using siRNA or by pre-treatment of cells with the TG2 enzyme inhibitor cystamine. Further analysis revealed that, whereas the full-length TG2 isoform (TG2-L) was almost completely cytoplasmic in its distribution, the majority of the short TG2 isoform (TG2-S) was membrane-associated in both parental and chemoresistant HepG2 cells. Following induction of cisplatin toxicity in non-chemoresistant parental cells, TG2-S together with cisplatin quickly relocated to the cytosolic fraction. Conversely, no cytosolic relocalisation of TG2-S or nuclear accumulation cisplatin was observed following identical treatment of chemoresistant cells, where TG2-S remained predominantly membrane-associated. This suggests that deficient subcellular relocalisation of TG2-S from membranous structures into the cytoplasm may limit the apoptic response to cisplatin toxicity in chemoresistant cells. Structural analysis of TG2 revealed the presence of binding motifs for interaction of TG-S with the membrane scaffold protein LC3/LC3 homologue that could contribute to a novel mechanism of chemotherapeutic resistance in HepG2 cells.

Introduction: Atrial fibrillation (AF) is a common cardiac arrhythmia whose prevalence rises with age and is linked to increased morbidity and mortality due to the risk of thromboembolism. Management typically involves anticoagulation and rhythm control, but the treatment of elderly patients with multiple comorbidities requires careful consideration of drug side effects and interactions. Cibenzoline, a Vaughan-Williams class IA antiarrhythmic, is effective against AF but has risks of toxicity, especially in older people and those with renal impairment, due to its renal excretion and prolonged half-life in these populations. Discussion: This paper presents a case of an 80-year-old woman with paroxysmal AF who suffered cardiac arrest due to cibenzoline toxicity despite receiving standard adjusted dosages. The patient's cibenzoline blood concentration was significantly higher than the therapeutic range, leading to cardiotoxicity, which was exacerbated by drug interactions with bisoprolol and edoxaban, both metabolized by the CYP3A4 enzyme. Venoarterial extracorporeal membrane oxygenation (V-A ECMO) and intra-aortic balloon pump (IABP) successfully managed the cardiac arrest. This case emphasizes the unpredictable pharmacokinetics of cibenzoline in elderly patients with renal impairment and the need for vigilant therapeutic drug monitoring to avoid adverse events. Conclusions: Cibenzoline can pose a significant risk of severe toxicity in elderly patients with renal impairment, and drug interactions may potentiate this risk. The paper underscores the importance of careful dose adjustment and monitoring of drug levels in this population. In cases of cibenzoline-induced cardiac arrest, V-A ECMO and IABP are effective treatment modalities. The case study serves as a critical reminder for clinicians to remain vigilant for drug-induced complications and to apply aggressive supportive treatments when necessary.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

The relationship between pangolin-CoV and SARS-CoV-2 has been a subject of debate. Further evidence of a special relationship between the two viruses can be found by the fact that all known COVID-19 viruses have abnormally hard outer shell (low M disorder; i.e., low content of intrinsically disordered residues in the membrane (M) protein) that so far was found in CoVs associated with burrowing animals, such as rabbits and pangolins, in which transmission involves virus remaining in buried feces for a long time. While a hard outer shell is necessary for viral survival, a harder inner shell could also help. For this reason, the N disorder range of pangolin-CoVs, not bat-CoVs, more closely matches that of SARS-CoV-2 especially when Omicron is included. The low N disorder (i.e., low content of intrinsically disordered residues in the nucleocapsid (N) protein), first observed in pangolin-CoV-2017 amd later in Omicron, is associated with attenuation according to the Shell-Disorder-Model. Our experimental study revealed that pangolin-CoV-2017 and SARS-CoV-2 Omicron (XBB.1.16 subvariant) show similar attenuations with respect to viral growth and plaque formation. Subtle differences have been observed that are consistent with disorder-centric computational analysis.

Vertical and horizontal bone augmentation is one of the most challenging techniques in bone engineering. The use of barrier membranes and scaffolds in guided bone regeneration (GBR) procedures is a common approach for the treatment of lost bone around teeth and dental implants. The aim of this study was to estimate the barrier effects of a synthetic poly (lactic acid/caprolactone) [P(PA/CL)] bilayer membrane for GBR, compared to a porcine collagen bilayer membrane, in the vertical augmentation model on 10–12-months old rat skull without periosteum. The HAp block (diameter: 4 mm, height: 3 mm, porosity:75%, average pore size:150 μm) was placed on the rat skull without a periosteum. The P(LA/CL) membrane (solid layer: 25 μm, porous layer: 175 μm) or the collagen membrane (solid layer, porous layer) was applied onto the HAp block. At 3, 6, and 12 weeks after the surgery, the incised tissues were fixed, decalcified, and stained with hematoxylin and eosin for histological evaluation. The P(LA/CL) membrane remained until 12 weeks and could achieve barrier effects to inhibit cellular invasion from the repositioned soft tissues. Local bone formation occurred in the interconnected pores of HAp at 6 weeks. On the other hand, the collagen membrane did not inhibit cellular invasion for its expansion until 3 weeks, and was absorbed until 6 weeks. The results indicated that the P(LA/CL) membrane might be effective in GBR as occlusive absorbable membrane.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

Helicobacter pylori is a gastric oncopathogen that infects over half of the world’s human population. It is a Gram-negative, microaerophilic, helix-shaped bacterium that is equipped with flagella, which provide high motility. Colonization of the stomach is asymptomatic in up to 90% of people but is a recognized risk factor for developing various gastric disorders such as gastric ulcers, gastric cancer and gastritis. Invasion of the human stomach occurs via numerous virulence factors such as CagA and VacA. Similarly, outer membrane proteins (OMPs) play an important role in H. pylori pathogenicity as a means to adapt to the epithelial environment and thereby facilitate infection. While some OMPs are porins, others are adhesins. The epithelial cell receptors SabA, BabA, AlpA, OipA, HopQ and HopZ have been extensively researched to evaluate their epidemiology, structure, role and genes. Moreover, numerous studies have been performed to seek to understand the complex relationship between these factors and gastric diseases. Associations exist between different H. pylori virulence factors, the co-expression of which appears to boost pathogenicity of the bacterium. Improved knowledge of OMPs is a major step towards combatting this global disease. Here, we provide a current overview of different H. pylori OMPs and discuss their pathogenicity, epidemiology and correlation with various gastric diseases.

The solvent extraction of gold(III) by undiluted 2-ethylhexanol or dissolved in toluene from HCl solution has been investigated. The numerical analysis of gold distribution data suggests the formation of HAuCl4·L and HAuCl4·2L (L= 2-ethylhexanol) species in the organic phase with formation constants K11= 38 and K12= 309, respectively. The results derived from gold(III) distribution have been implemented in a solid-supported liquid membrane system. The influence of several variables on gold transport was considered: feed and receiving phases stirring speeds, HCl and gold concentrations in the feed phase and carrier concentration in the membrane phase as well as the presence of base metals (Fe,Cu,Ni) and PGMs in the feed phase. Also, diffusional resistances to mass transfer are estimated. Gold is recovered as zero valent nanoparticles.

Membrane-based sensors (MePSs) exhibit remarkable precision and sensitivity in detecting pressure changes. MePSs are commonly used to monitor catalytic reactions in solution, generating gas products crucial for signal amplification in bioassays. They also allow catalyst quantification by indirectly measuring the pressure generated by the gaseous products. This is particularly interesting to detect enzymes in biofluids associated with disease onset. To enhance the performance of a MePS, various structural factors influence membrane flexibility and response time, ultimately dictating the device's pressure sensitivity. In this study, we fabricated MePSs using polydimethylsiloxane (PDMS) and investigated how structural modifications affect the Young's modulus (E) and residual stress (σ0) of the membranes. These modifications have a direct impact on the sensors' sensitivity to pressure variations, observed as a function of the volume of the chamber (Σ) or of the mechanical properties of the membrane itself (S). MePSs exhibiting the highest sensitivities were then employed to detect catalyst quantities inducing the dismutation of hydrogen peroxide, producing dioxygen as gaseous product. As a result, catalase enzyme was successfully detected using these optimized MePSs, achieving a remarkable sensitivity of (22.7 ± 1.2) µm/nM and a limit of detection (LoD) of 396 pM.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

Abstract: Nowadays, there is an increasing interest in the development of novel bioresorbable membranes for Guided Bone Regeneration (GBR). Hydroxyapatite of different resources in com-bination with chitosan has been used successfully. In this work, armored catfish (Pterygoplich-thys spp) bone as a source of hydroxyapatite is proposed; it was isolated through bone calcina-tion at a temperature of 1000 °C. The hydroxyapatite obtained was analyzed for its chemical composition by means of Energy Dispersive Spectroscopy (EDS), its functional groups by Fouri-er Transform Infrared Spectroscopy (FT-IR), its crystallographic structures were analyzed by X-ray diffraction (DRX) and Scanning electron microscopy (SEM) was used to observe the mor-phology of the particle. The composed membrane presents a major roughness morphology sur-face than the pristine chitosan membrane. The hydroxyapatite particles added to the polymeric matrix increased the mechanical tensile properties of the membrane. These findings confirm that armored catfish bones are a viable, economic, and environmentally friendly source of hydroxy-apatite, which combined with chitosan, is a suitable alternative to develop biocompatible GBR membranes after it is combined with chitosan.

The physiological mechanism of membrane potential generation relies on the passage of mobile ions across the plasma membrane, which is selectively permeable to mobile ions. The existence of a membrane and the transport of ions across it are essential for the generation of membrane potential. However, a long-forgotten theory, Association-Induction hypothesis, asserts that the heterogeneous distribution of charges in space, due to ion adsorption, is the true cause of membrane potential generation. Using an artificial living cell model consisting of a viscous aqueous solution, the mechanism of membrane potential generation is restudied in this work. The results indicate that membrane potential can be generated even in the absence of a plasma membrane and that ion adsorption leading to a heterogeneous spatial charge distribution is an essential factor for membrane potential generation. Consequently, the authors invites people to reconsider the Association-Induction hypothesis as a genuine mechanism for generating membrane potential.

The molecular mechanism how the infecting DNA of bacteriophage T4 is passing from the capsid through the bacterial cell wall and entering the cytoplasm is essentially unknown. After adsorption, the short tail fibers of the infecting phage extend from the baseplate and trigger the contraction of the tail sheath, leading to a puncturing of the outer membrane by the tail tip needle composed of the proteins gp5.4, gp5 and gp27. To explore the events that occur in the periplasm and at the inner membrane, we have constructed T4 phage that have a modified gp27 in their tail tip with a His-tag. Shortly after infection with these phages, the cells were chemically cross-linked, solubilised, and the cross-linked products were affinity purified on a nickel column. The co-purified proteins were identified by mass spectrometry, and we found that predominantly the inner membrane proteins DamX, SdhA and PpiD were cross-linked. The same partner proteins were identified when purified gp27 was added to Escherichia coli spheroplasts suggesting a direct protein-protein interaction.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

The urgent global health challenge posed by methicillin-resistant Staphylococcus aureus (MRSA) infections demands effective solutions. Antimicrobial peptides (AMPs) represent promising tools of research of new antibacterial agents and LyeTx I mn∆K, a short synthetic peptide based on the Lycosa erythrognatha spider venom, is a good representative. This study focused on analyzing some antimicrobial activities of LyeTx I mn∆K, including minimum inhibitory and bactericidal concentrations, synergy and resensitization assays, lysis activity, the effect on biofilm, and the bacterial death curve in MRSA. Additionally, its characterization was conducted through isothermal titration calorimetry, dynamic light scattering, calcein release, and finally, efficacy in a mice wound model. The peptide demonstrating remarkable efficacy against planktonic cells and biofilms of MRSA, outperforms vancomycin in terms of rapid bactericidal action and anti-biofilm effects. The mechanism involves significant membrane damage. Interactions with bacterial model membranes, including those with lysylphosphatidylglycerol (LysylPOPG) modifications, highlight versatility and selectivity of this compound. Also, the peptide has the ability to sensitize resistant bacteria to conventional antibiotics, showing potential for combinatory therapy. Furthermore, using an in vivo model, was showed that a formulated gel containing the peptide proved superior to vancomycin in treating MRSA-induced wound in mice. Together the results highlight LyeTx I mnΔK as a promising prototype for the development of effective therapeutic strategies against superficial MRSA infections.

Articular cartilage healing and repair is one of the biggest clinical challenges in trauma and orthopaedic medicine, leading to high economic loss due to athletic impairment in sport horses. Multipotent Mesenchymal stem/stromal cells are part of novel therapeutic arsenal aimed at tissue regeneration and restoring organ function. These cells release biomolecules and factors in the culture media, producing the so called conditioned medium, which have a pro-regenerative effect through paracrine mechanisms. Considering this, a therapeutic product combining equine synovial membrane derived Mesenchymal stem/stromal cells and equine umbilical cord stroma-derived Mesenchymal stem/stromal cells conditioned medium was employed. In this work the treatment of two articular defects, in the first phalanx and third metacarpus of the left front limb of a five-year-old horse, is described. Following surgical debridement of the lesions, the treatment comprised two intra-articular administrations of the above-mentioned therapeutic combination, 15 days apart. This was followed by a thorough rehabilitation program. A second-round treatment was performed 6 months later. Diagnostic imaging demonstrated significant improvement of the articular defects. The clinical outcome allowed a full return to the athletic performance demonstrating the safety and potential advantages of this approach when compared with other therapeutic options.

Membrane nanotubes (NTs) are dynamic communication channels connecting spatially separated cells even over long distances and promoting the transport of different cellular cargos. NTs are also involved in the intercellular spread of different pathogens and the deterioration of some neuro-logical disorders. Transport processes via NTs may be controlled by cytoskeletal elements. NTs are frequently observed membrane projections in numerous mammalian cell lines including various immune cells, but their functional significance in the ‘antibody factory’ B cells is poorly elucidated. Here we report that as active channels, NTs of B cells can mediate bidirectional mitochondrial transport, promoted by the cooperation of two different cytoskeletal motor proteins, kinesin along microtubules and myosin VI along actin, and bidirectional transport processes are also supported by the heterogeneous arrangement of the main cytoskeletal filament systems of the NTs. We revealed that despite NTs and axons being different cell extensions the mitochondrial transport they mediate may exhibit significant similarities. Furthermore, we found that microtubules may improve the stability and lifespan of B cell NTs, while F-actin strengthens NTs by providing a structural framework for them. Our results may contribute to a better understanding of the regulation of the major cells of humoral immune response to infections.

Temporal lobe epilepsy (TLE) is associated with reorganization of hippocampal neuronal net-works, gliosis, neuroinflammation, loss of integrity of the blood-brain barrier (BBB) in humans and animal models. More than 30% of epilepsies remain intractable and characterization of the molecular mechanisms involved in BBB dysfunction is essential to the identification of new thera-peutic strategies. In this work, we induced status epilepticus in rats by injection of the proconvul-sant drug pilocarpine that leads to TLE. Using RT-qPCR, double immunohistochemistry and con-focal imaging, we studied at different time points of epileptogenesis (latent phase, 3, 7, 14 days; chronic phase, 1 and 3 months) the regulation of reactive glia and vascular markers. In the hippo-campus, increased expression of mRNA encoding the glial proteins GFAP and Iba1 confirmed neu-roinflammatory status. We report for the first time the concomitant induction in endothelial cells, pericytes and basement membrane of the BBB of specific proteins CD31, PDGFR and ColIV, that peaks at the same time points as inflammation. The altered expression of these proteins occurs ear-ly in TLE, during the latent phase, suggesting that they could be associated with early rupture and pathogenicity of the BBB that will contribute to the chronic phase of epilepsy.

A simple model is developed for membrane fouling, taking into account two main fouling phenomena: cake formation, due to attached solids onto the membrane surface and pores clogging, due to retained compounds inside the pores. The model is coupled with a simple anaerobic digestion model for describing the dynamics of an Anaerobic Membrane BioReactor (AnMBR). In simulations, we investigate its qualitative behavior: it is shown that the model exhibits satisfying properties in terms of flux decrease due to membrane fouling. Comparing simulation and experimental data, the model is shown to predict quite well the dynamics of an AnMBR. The simulated flux best fits the experimental flux with a correlation coefficient r2=0.968 for the calibration data set and r2=0.938 for the validation data set. General discussions are given on possible control strategies to limit fouling and optimize the flux production. We show in simulations that these strategies allow one to increase the mean production flux to 33 L/(h.m2), whereas without control it was 18 L/(h.m2).

Proton exchange membrane (PEM) fuel cells have emerged as a viable alternative energy production source for stationary and transportation applications. Reliable and sustainable fuel cell operation requires effective water management. Membrane water content can vary along the stack during transients which can lead to losses in fuel cell performance. To control these variations a model that predicts the internal humidity dynamics of the stack is needed. In this study, a control-oriented model for predicting membrane water content variation was developed and implemented in MATLAB/Simulink. A lumped parameter model was initially developed and then further discretized into smaller control volumes to track humidity distribution along the stack. To validate the model’s predictions, the predicted results were compared to computer simulation results from GT-Suite. The root mean square error (RMSE) between the model’s prediction and GT-Suite’s simulation results was found to be within 1.5 membrane water content for all cases, demonstrating the model’s capability to capture the variation of membrane water content along the stack. The developed model will be useful for real-time control of membrane water content variation in PEM fuel cells.

The Self-Forming Dynamic Membrane BioReactor (SFD MBR) is a cost-effective alternative to conventional MBR, where the synthetic membrane is replaced by the “cake layer”, an accumulation of the biological suspension over a surface of inert low-cost support, caused by a suction force. Under optimized conditions, the cake layer reveals easy to remove and quick to form again, resulting a “dynamic membrane”. The permeate of SFD MBR has chemo-physical characteristics comparable to those of conventional MBR. In this paper, two nylon meshes with a pore-size of 20 and 50 µm respectively were tested in a bench scale SFD MBR where a periodic air mass load (AML) was supplied tangential to the filtration surface to maintain filtration effectiveness. The SFD MBR equipped with the 20 µm nylon mesh coupled to 5 min of AML every 4 hours showed the best performance both ensuring a permeate with turbidity values always below 3 NTU and revealing no critical fouling. A benchmark test, conducted in the same experimental time, with identical operating conditions, and the only difference of a suction break (relaxation) instead of the AML. This latter test produced a permeate of very good quality, but it needed frequent mesh cleanings, showing that a periodic AML coupled with the use of a 20 µm mesh can be a good strategy for long term operation of SFD MBR.

The presented work is aimed at studying the gas transport characteristics of polymeric hollow-fibre gas separation membranes. Such materials as: polysulfone (PSF), polyphenylene oxide (PFO), polyetherimide (PEI), polyetherimide with polyimide (PEI+PI) were studied on the example of air mixture separation. The values of the permeances of pure gases O2 and N2 and the mixed permeances of oxygen and nitrogen during air separation were obtained. Mathematical models of the gas separation process built on the basis of these values show significant discrepancies. To obtain a gas mixture with 95 mol.% nitrogen from air, taking into account the mixture permeance, 15.8% more PSF membrane area is required than taking into account the permeance of pure gases. For a PPO membrane this value is 13.9%, for PEI 19.8% less area is required, and for PEI+PI 15.9% less. In the design of industrial or semi-industrial membrane installations, such discrepancies can lead to significant errors, including technical and economic ones.

Background: We aimed to explore microvascular changes evaluated with optical coherence tomography angiography (OCTA) in patients undergoing epiretinal membrane (ERM) pars-plana vitrectomy (PPV) combined with intravitreal Ozurdex implantation, compared with standard PPV. (2) Methods: Prospective interventional analysis on 25 eyes undergoing PPV+Ozurdex (Group A) and 25 eyes undergoing PPV alone. Best corrected visual acuity (BCVA) and OCTA parameters, such as vessel density (VD) of the superficial and deep capillary plexi (SCP and DCP) in the whole 6.4x6.4 mm and fovea area, were evaluated preoperatively and 3 months after surgery. (3) Results: Postoperative BCVA significantly improved in both groups. No cases of post-operative cystoid macular edema (CME) were reported in Group A vs. 2 eyes in Group B. In Group A we found a statistically significant increase of SCP’s VD in either the whole image (from 42.1±4.1 to 45.6±4.3 %, p=0.01) and the fovea image (from 38.5±7.5 to 41.7±4.2%, p=0.03). In Group B, we reported no significant variations in the SCP’s VDs. In the DCP, VD significantly increased only in the whole image in Group A. Stage 4 ERMs showed the greatest improvement in VD, especially in Group A. (4) Conclusions: In conclusion, intraoperative Ozurdex prompted a significant BCVA recover and limited the occurrence of postoperative CME compared to the standard procedure. Moreover, Ozurdex implant is associated with a better restoration of microvascular structure in either SCP and DCP.

This study investigates the emergence of ertapenem-resistant, meropenem-susceptible (ErMs) among non-carbapenemase producing (NCP) and carbapenemase producing (CP) Escherichia coli and Klebsiella pneumoniae. As mutations for ertapenem resistance establish the genetic background for non-carbapenemase meropenem resistance, there is a great need for antibiotic stewards and researchers to understand the determinants of a strain’s propensity to become resistant. Whole genome sequencing was conducted on clinical carbapenem-resistant E. coli (CREC) and K. pneumoniae (CRKP) across 5 hospitals in San Antonio, U.S. from 2012-2018. The majority of carbapenem resistant Enterobacterales (CRE) were NCP (54%; 41/76). The blaCTX-M was found to be most prevalent among NCP isolates (p = 0.02). LC-MS/MS analysis of carbapenem hydrolysis revealed that blaCTX-M-mediated carbapenem hydrolysis, indicating the need to reappraise the term, “non-carbapenemase (NCP)” for quantitatively uncharacterized CRE strains harboring blaCTX-M. Antimicrobial susceptibility results showed that 56% of all NCPE isolates had an ErMs phenotype (NCPE vs. CPE, p < 0.001), with E. coli driving the phenotype (E. coli vs. K. pneumoniae, p < 0.001). ErMs strains carrying blaCTX-M, had approximately 4-fold more copies of blaCTX-M than ceftriaxone-resistant but ertapenem and meropenem susceptible (EsMs) isolates (3.7 v. 0.9, p < 0.001). ErMs also carried more mobile genetic elements (MGEs), particularly IS26 composite transposons, than EsMs (37 vs. 0.2, p < 0.0001). Immunoblot analysis demonstrated the absence of OmpC expression in NCP-ErMs E. coli, with 92% of strains lacking full contig coverage of ompC. Overall, this work provides evidence of a collaborative effort between blaCTX-M and OmpC in NCP strains that confer resistance to ertapenem but not meropenem. To thwart potential mismanagement of CRE infected patients, future efforts should focus on understanding the mechanism(s) underlying OmpC loss, developing rapid methods to detect blaCTX-M copy number variants, and targeted antimicrobials for NCPE and ErMs strains.

Births occurring before thirty-seven weeks of gestation are referred to as preterm births (PTBs), which is the primary cause of neonatal mortality and long-term disabilities. The unknown mechanism behind PTB makes diagnosis difficult, yet early detection is necessary for controlling and averting related consequences. The primary focus of this work is to provide an overview of the known risk factors associated with preterm labor and the conventional and advanced procedures for early detection of PTB, including multi-omics and artificial intelligence (AI)/machine learning (ML)-based approaches. It also discusses the principles of detecting various proteomic biomarkers based on lateral flow immunoassay and microfluidic chips, along with the commercially available point-of-care testing (POCT) devices and associated challenges. After briefing the therapeutic and preventive measures of PTB, the review summarizes with an outlook.

Chen, et al., compared two modified polyurethane-based wound dressings (PUE and PUESi), both intended for use in chronic wounds, with a negative control (gauze) and a positive control (PolyMem) via a series of preliminary in vitro and rodent model tests. Future studies may find that one or both of these two new dressings are beneficial. However, the results of this first study cannot be relied upon. Although they exhibited in-depth knowledge of manufacturing techniques, the study designers seem far less familiar with the science of wound healing and with PolyMem wound dressings. This helps explain the flaws in the methods that lead to many of their tests not being translatable to real-world settings. In addition, the interpretation of some of the test results is questionable.

Metal-organic frameworks (MOFs) represent the largest class of materials among the crystalline porous materials ever developed and have attracted attention as core materials for separation technology. Their extremely uniform pore aperture and nearly unlimited structural and chemical characteristics have attracted great interest and promise in applying MOFs to adsorptive and membrane–based separations. This paper reviews the recent research and development of MOF membranes for gas separation. Strategies for polycrystalline membranes and mixed matrix membranes are discussed, with a focus on separation systems involving hydrocarbon separation and CO2 capture. Challenges and opportunities for the industrial deployment of MOF membranes are also be discussed, providing guidance for the design and fabrication of future high-performance membranes. The contributions of the underlying mechanism to separation performances, and the adopted strategies and membrane processing technologies for breaking the selectivity/permeability trade–off are discussed.

In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.

In this study, the hybrid biological ion exchange (BIEX) resin and gravity-driven membrane (GDM) process was employed for the treatment of coloured and turbid river water. The primary objective was to investigate the impact of both physical and chemical cleaning methods on ceramic and polymeric membranes in terms of stabilised flux, flux recovery after physical/chemical cleaning, and permeate quality. To address these objectives, two types of MF and UF membranes were utilised (M1 = polymeric MF, M2 = polymeric UF, M3 = ceramic UF, and M4 = lab-made ceramic MF).Throughout extended operation, the resin functioned initially in the primary ion exchange (IEX) region (NOM displacement with pre-charged chloride) and progressed to a secondary IEX stage (NOM displacement with bicarbonate and sulphate), while membrane flux remained stable. Subsequently, physical cleaning involved air/water backwash with two different flows and pressures, and chemical cleaning utilised NaOH at concentrations of 20 and 40 mM, as well as NaOCl at concentrations of 250 and 500 mg Cl2/L. These processes were carried out to assess flux recovery and identify fouling reversibility. The results indicated an endpoint of 1,728 bed volumes (BV) for the primary IEX region, while the secondary IEX continued up to 6,528 BV. At the end of the operation, DOC and UVA254 removal in the effluent of the BIEX columns were 68% and 81%, respectively, compared to influent water. This was followed by 30% and 57% DOC and UVA254 removal by M4 (ceramic MF). The stabilised flux remained approximately 3.8 – 5.2 LMH both before and after the cleaning process, suggesting that membrane materials do not play a pivotal role. The mean stabilised flux of polymeric membranes increased after cleaning, whereas that of ceramics decreased. Enhanced air–water backwash flow and pressure resulted in increased removal of hydraulic reversible fouling, which was identified as the dominant fouling type. Ceramic membranes exhibited higher removal of reversible hydraulic fouling than polymeric membranes. Chemical cleaning had a low impact on flux recovery; therefore, we recommend solely employing physical cleaning.

Cathepsin B (CatB) is thought to be essential for the induction of Porphyromonas gingivalis lipopolysaccharide (Pg LPS)-induced Alzheimer’s disease- like pathologies in mice, including interleukin-1β (IL-1β) production and cognitive decline. However, little is known about the role of CatB in Pg virulence factor-induced IL-1β production by microglia. We first subjected IL-1β-luciferase reporter BV-2 microglia to inhibitors of Toll-like receptors (TLRs), IκB kinase, and the NLRP3 inflammasome following stimulation with Pg LPS and outer membrane vesicles (OMVs). To clarify the involvement of CatB, we used several known CatB inhibitors, including CA-074Me, ZRLR, and human β-defensin 3 (hBD3). IL-1β production in BV-2 microglia induced by Pg LPS and OMVs was significantly inhibited by the TLR2 inhibitor C29 and the IκB kinase inhibitor wedelolactonne, but not by the NLRPs inhibitor MCC950. Both hBD3 and CA-074Me significantly inhibited Pg LPS-induced IL-1β production in BV-2 microglia. Although CA-074Me also suppressed OMV-induced IL-1β production, hBD3 did not inhibit it. Furthermore, both hBD3 and CA-074Me significantly blocked Pg LPS-induced nuclear NF-κB p65 translocation and IκBα degradation. In contrast, hBD3 and CA-074Me did not block OMV-induced nuclear NF-κB p65 translocation or IκBα degradation. Furthermore, neither ZRLR, a specific CatB inhibitor, nor shRNA-mediated knockdown of CatB expression had any effect on Pg virulence factor-induced IL-1β production. Interestingly, phagocytosis of OMVs by BV-2 microglia induced IL-1β production. Finally, the structural models generated by AlphaFold indicated that hBD3 can bind to the substrate-binding pocket of CatB, and possibly CatL as well. These results suggest that Pg LPS induces CatB/CatL-dependent synthesis and processing of pro-IL-1β without activation of the NLRP3 inflammasome. In contrast, OMVs promote the synthesis and processing of pro-IL-1β through CatB/CatL-independent phagocytic mechanisms. Thus, hBD3 can improve the IL-1β-associated vicious inflammatory cycle induced by microglia through inhibition of CatB/CatL.

Membrane protein integrase (MPIase), an endogenous glycolipid in Escherichia coli (E. coli) membrane, is essential for membrane protein insertion in E. coli. We have examined Sec-independent membrane protein insertion mechanisms facilitated by MPIase using physicochemical analytical techniques such as solid-state nuclear magnetic resonance, fluorescence measurements, and surface plasmon resonance. In this review, we outline the physicochemical characteristics of membranes that may affect membrane insertion of proteins. Subsequently, we introduce our results verifying the effects of membrane lipids on insertion and estimate the impact of MPIase. Although MPIase is a minor component of E. coli membranes, it regulates insertion by altering the physicochemical properties of the membrane. In addition, MPIase promotes insertion by interacting with substrate proteins. We propose comprehensive mechanisms of membrane insertion of proteins involving MPIase, which provide a physicochemical basis for understanding the roles of glycolipids in protein translocation.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

The recovery and recycling of metals that generate toxic ions in the environment is of particular importance, especially when these are tungsten and, in particular, thorium. The radioactive element thorium has unexpectedly accessible domestic applications (filaments of light bulbs and electronic tubes, welding electrodes, working alloys containing aluminum and magnesium), which lead to its appearance in electrical and electronic waste from municipal waste management platforms. The current paper proposes the simultaneous recovery of waste containing tungsten and thorium from welding electrodes. The simultaneous recovery is done by applying a hybrid membrane electrolysis technology coupled with nanofiltration. An electrolysis cell with sulphonated polyether–ether–ketone membranes (sPEEK) and a nanofiltration module with chitosan-polypropylene membranes (C–PHF–M) are used to carry out the hybrid process. The analysis of welding electrodes led to a composition of: W (tungsten) 89.4%; Th 7.1%; O2 2.5% and Al 1.1%. Thus, the parameters of the electrolysis process were chosen according to the speciation of the three metals suggested by the superimposed Pourbaix diagrams. At a constant potential of 20.0 V and an electrolysis current of 1.0 A, the pH is varied and the possible composition of the solution in the anodic workspace is analyzed. Favorable conditions for both electrolysis and nanofiltration were obtained at pH from 6 to 9, when the soluble tungstate ion, the aluminum hydroxide and solid thorium dioxide were formed. Through a first nanofiltration, the tungstate ion is obtained in the permeate, and thorium dioxide and aluminum hydroxide in the concentrate. By adding a pH 13 solution over the two precipitates, the aluminum is solubilized as sodium aluminate which will be found after the second nanofiltration in permeate, the thorium dioxide remaining integrally (within an error of ±0.1ppm) on the C–PHF–M membrane.

Natural Gas (NG) processing is a prominent industrial separation process. Among the available techniques, the innovative membrane process shows potential for efficient removal of impurities, including carbon dioxide (CO₂). This study focuses on utilizing breakthroughs in membrane separation to drive sustainable CO₂ extraction from natural gas. Through comprehensive research and analysis, we explore the effectiveness and feasibility of membrane-based systems in removing CO₂ impurities from NG, thus promoting greener and more sustainable industrial practices. Our findings underscore the transformative nature of membrane separation technology, presenting new possibilities for a more environmentally-friendly and sustainable approach to CO₂ extraction from natural gas.Natural Gas (NG) processing utilizes various techniques for impurity removal, with the membrane process emerging as a promising option for efficient carbon dioxide (CO₂) extraction. This research proposes the integration of a simple mathematical model into ASPEN HYSYS to design a membrane system for CO₂/CH₄ separation. The study also investigates parameter sensitivities by altering operating conditions, such as feed composition and pressure, as well as membrane properties, including selectivity. By analyzing these variables, we aim to optimize the performance and efficiency of the membrane system, facilitating the sustainable extraction of CO₂ from NG. The findings contribute to advancing the design and operation of membrane-based processes for CO₂ separation, paving the way for greener and more sustainable industrial practices. In addition, this study explores various configurations for optimizing the design of the membrane system, including single-stage with and without recycling as well as double-stage configurations. The investigation demonstrates that methane recovery can be enhanced through the recycling of the permeate stream and by implementing a double stage membrane system. These findings highlight the potential for improving the efficiency and performance of the membrane system, enabling higher methane recovery rates. By considering different configurations, this research contributes to the development of more effective and sustainable CO₂ extraction processes from natural gas.

Peptide/Histidine Transporter PHT1 (SLC15A4) is expressed in lysosomal membranes of immune cells where it plays an important role in metabolic and inflammatory signaling. PHT1 is an H+-coupled/histidine symporter that can transport a broad range of oligopeptides, including a variety of bacterial-derived peptides. Moreover, it enables the scaffolding of various metabolic signaling molecules and interacts with key regulatory elements of the immune response. Therefore, it is not surprising that PHT1 is associated with the development of autoimmune diseases, such as systemic lupus erythematosus (SLE). Unfortunately, the pharmacological development of PHT1 has been hampered by the lack of appropriate transport assays. With the aim to address this shortcoming, a novel transport assay based on solid supported membrane-based electrophysiology (SSME) is presented. Key findings of the present SSME studies include the first recordings of electrophysiological properties, a pH dependence analysis, an assessment of PHT1 substrate selectivity, as well as the transport kinetics of the identified substrates. In contrast to previous works, PHT1 is studied its native lysosomal environment. Moreover, observed substrate selectivity is validated by molecular docking. Overall, this new SSME-based assay is expected to contribute to unlock the pharmacological potential of PHT1 and to deepen the understanding of its functional properties.

The Spiking Neural Network (SNN) has attracted more and more attention recently. It adopts binary spike signals to transmit information. Benefitting from the information passing paradigm of SNNs, the multiplications of activations and weights can be replaced by additions, which are more energy-efficient. However, its ``Hard Reset" mechanism for the firing activity would ignore the difference among membrane potentials when the membrane potential is above the firing threshold, causing information loss. Meanwhile, quantifying the membrane potential to 0/1 spikes at the firing instants will inevitably introduce the quantization error thus bringing about information loss too. To address these problems, we propose to use the ``Soft Reset" mechanism for the supervised training-based SNNs, which will drive the membrane potential to a dynamic reset potential according to its magnitude, and Membrane Potential Rectifier (MPR) to reduce the quantization error via redistributing the membrane potential to a range close to the spikes. Results show that the SNNs with the ``Soft Reset" mechanism and MPR outperform their vanilla counterparts on both static and dynamic datasets.

A single type I RC (Fe-S type, ferredoxin reducing) is found in several of the phyla of anoxygenic phototrophic bacteria. They include the heliobacteria (HB), the green sulfur bacteria (GSB) and the chloroacidobacteria (CAB), for which high-resolution homodimeric RC-PS structures have recently appeared [1-4]. The 2.2-Å Xray structure of the RC-PS of Heliomicrobium modesticaldum [1] revealed that the core PshA apoprotein (PshA1 and PshA2 homodimeric pair) exhibits a structurally conserved PSI arrangement comprised of five C-terminal transmembrane helices (TMHs) forming the RC domain and six N-terminal TMHs coordinating the light-harvesting (LH) pigments. The Hm. modesticaldum structure lacked quinones, indicating that electrons were transferred directly from the A0 (81-OH-chlorophyl (Chl) a) primary acceptor to the FX [4Fe4S] component, serving as the terminal RC acceptor. A pair of additional TMHs designated as Psh X were found, that function as a low-energy antennae. The 2.5Å resolution cryo-electron microscopy (cryo-EM) structure for the RC-PS of the GSB Chlorobaculum tepidum [2] included two Fenna-Matthews-Olson protein (FMO) antennae, which transfer excitations from the chlorosomes to the RC-PS (PscA1 and PscA2) core. Two cytochromes c (PscC) molecules were revealed, which act in series as electron donors to the photooxidized RC BChl a’ special pair, as well as PscB, housing the [4Fe-4S] cluster FA and FB, and the associated PscD protein [3]. Although their FMO components were missing from the 2.6-Å cyro-EM structure of the Zn-BChl a’ special pair containing RC-PS of Chloroacidobacterium thermophilum [4], a unique architecture was revealed that consisted of seven additional subunits including PscZ in place of PscD, the PscX and PscY cytochrome c serial electron donors and four low mol. wt. subunits of unknown function. Overall, these diverse structures have revealed that: (i) the HB RC-PS is the simplest light-energy transducing complex yet isolated, and represents the closest known homolog to a common homodimeric RC-PS ancestor; (ii) the symmetrically localized Ca2+binding sites found in each of the Type I homodimeric RC-PSs likely gave rise to the analogously positioned Mn4CaO5 cluster of the PSII RC and the TyrZ RC donor site; (iii) a close relationship between the GSB RC-PS and Chl protein (CP)43 and CP47 of PSII was demonstrated by the strongly conserved locations of their LH-(B)Chls; (iv) LH-BChls of the GSB-RC-PS are also localized in the conserved RC-associated positions of the PSII ChlZ-D1 and ChlZ-D2 sites; (v) glycosylated carotenoids of the GSB RC-PS are located in the homologous carotenoid-containing positions of PSII, reflecting an O2-tolerance mechanism capable of sustaining early stages in the evolution of oxygenic photosynthesis. In addition to the close relationships found between the homodimeric RC-PS and PSII, duplication of the gene encoding the ancestral Type I RC apoprotein, followed by genetic divergence my well account for the appearance of the heterodimeric Type I and Type II RC found in extant oxygenic phototrophs. Accordingly, the long-held view that PSII arose from the anoxygenic Type II RC is now supplanted by the new evidence provided by Type I RC-PS homodimer structures, indicating that the evolutionary origins of anoxygenic Type II RCs along with their distinct antenna rings are likely to have occured later than the events which gave rise to their oxygenic counterparts.

Triphenylphosphonium (TPP) derivatives of a decapeptide related to sequences of bactenecin 7 (Bac7) and oncocin (Onc112) were synthesized and studied as potential antimicrobial compounds using various biochemical and microbiological assays. It was shown that while the reduction of the Bac7 length to 10 a.a. residues dramatically decreases the affinity to bacterial ribosomes, the modification of peptide with alkyl-TPP moieties leads to an increase in the affinity. New analogs which structure combines a decapeptide related to Bac7 and Onc112 — Bac(1-10, R/Y) — and TPP, attached to the C-terminal amino acid residue through alkylamide linkers, inhibit translation in vitro and are found to be more selective inhibitors of bacterial translation as compared with eukaryotic translation, than Onc112 and Bac7. Triphenylphosphonium analogs of a decapeptide related to Bac7 and Onc112 suppress the growth of both gram-negative bacteria, similar to Onc112 and Bac7, and gram-positive ones as alkyl-TPP derivatives, and also act against some resistant laboratory strains. Bac(1-10, R/Y)-C2-TPP, containing a short alkylamide linker between the decapeptide and TPP, is transferred into the E. coli cells via the SbmA transporter protein. TPP derivatives of the decapeptide Bac(1-10, R/Y) containing either decylamide or ethylamide linker cause B. subtilis membrane depolarization, similar to alkyl-TPP. The Bac(1-10, R/Y)-C2-TPP analog is proved to be non-toxic for mammalian cells by MTT-test.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

Recent works identified ClpXP, mitochondrial caseinolytic protease, as the only target of imipridones - new class of antitumor agents. Our study of the mechanism of imipridone derivative TR-57 action in SUM159 human breast cancer cells demonstrated mitochondrial fragmentation, degradation of mitochondrial mtDNA and mitochondrial dysfunction, due to inhibition of Complex I and Complex II activity. Complete inhibition of oxidative phosphorylation accom-panied with 90, 94, 88 and 87% decrease in the content of Complex I, II, III and IV proteins, respectively. The content of the FOF1-ATPase subunits decreased sharply by approximately 35% after 24 hours and remained unchanged up to 72 hours of incubation with TR-57. At the same time, a disappearance of the ATPIF1, natural inhibitor of mitochondrial FOF1-ATPase observed after 24 h exposure to TR-57. ATPase inhibitor oligomycin had no effect on the mitochondrial membrane potential in intact SUM159, whereas it caused a 65% decrease in TR-57-treated cells. SUM159 cells incubated with TR57 up to 72 hours retained the level of proteins facilitating the ATP transfer across the mitochondrial membranes: VDAC1 expression was not affected, while expression of ANT-1/2 and APC2 increased by 20% and 40%, respectively. Thus, our results suggest that alt-hough TR-57 treatment lead to complete inhibition of respiratory chain activity of SUM159 cells, hydrolysis of cytoplasmic ATP by reversal activity of FOF1-ATPase supports mitochondrial polarization.

A cross-flow ultrafiltration harvesting system of a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with the effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomass was then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L1 with an average of 9.7 g·L1). Concentration ratios of 15-27 were obtained with average transmembrane fluxes ranged from 5 to 28 L·m2·h1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from the biogas production from the anaerobic valorisation of the harvested microalgae.

Membrane processes, such as microfiltration, ultrafiltration, and nanofiltration are increasingly used for various applications in both upstream and downstream processing. Membrane-based processes play a critical role in the field of separation/purification of biotechnological products, including protein production/purification. The possibility of using membranes to separate peptides from a chicken byproduct hydrolysate and the effect of the performed downstream processing on the DPP-IV inhibitory activity of MDCR (mechanical deboning chicken residue) has been investigated. The chicken byproduct hydrolysate was prepared by enzymatic hydrolysis followed by MF, UF, NF, and RO separation. The LC-OCD analysis confirmed that NF and RO would retain the bioactive peptides in the concentrate in comparison to MF and UF. Bioactivity was correlated with molecular weight distribution profiles and average molecular weights. Permeates after ultrafiltration showed an IC50 value of 0.75 mg/mL, comparable to other potent DPP-IV inhibitors derived from various food sources, and significantly more potent compared to the microfiltration sample, which showed an IC50 value of 1.04 mg/mL. The average molecular weight of the permeates calculated from the SEC chromatograms was 883 g/mol for UF and 1437 g/mol for MF. Of the four membranes studied, the UF membrane showed the best separation properties with respect to maximizing the yield and up-concentration of the bioactive peptides. Overall, UF was demonstrated to be a feasible technology for the removal of the undesired high molecular weight substances and up-concentration of small molecular weight bioactive peptides from chicken byproduct hydrolysate.

The air is a fundamental element for the life on Earth. Rapid urbanization and industrialization release large amounts of pollutants (harmful gases, microorganisms, and particulate matter, among others) into the atmosphere, leading to health hazards. Air filtration is still the most used and promising technique for protecting air against pollutants. The quality and efficiency of filtering process are dependent of material used for the filter and other filter’s properties. Several methods can be used for manufacturing filters, one of them uses fibrous membranes obtained through electrospinning from polymeric solutions. Electrospinning is a technique that combines the application of an electrostatic field to a moving fluid which results in the fibers formation. Electrospun membranes are constituted by fibers that the sizes spread on submicro and or nanometric scales. This review focuses on fiber membranes obtained by electrospinning for filtration of particulate matter. It is addressed the effect of solution, processing and ambient parameters on the morphology and dimensional characteristics of fiber membranes. The basic principles of air filtration and test and characterization of filter performance are presented. The research progress on electrospun nanofibers as air filters in recent years is summarized and examined. Finally, conclusion and future perspectives in electrospun fibers for air filtration are provided and discussed.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

Horses are high performance athletes prone to sportive injuries such as tendonitis and desmitis. The formation of fibrous tissue in tendon repair becomes a therapeutic challenge to overcome. This impels regenerative medicine to develop innovative therapies that enhance tissue regenera-tion retrieving original tissue properties. Multipotent Mesenchymal Stem/ Stromal Cells (MSCs) have been successfully used to develop therapeutic products, as they secrete a variety of bioac-tive molecules that play a pivotal role in tissue regeneration. These factors are released in cul-ture media producing conditioned media (CM). The aforementioned assumptions led to the formulation of equine synovial membrane MSCs (eSM-MSCs) – the cellular pool that naturally regenerates joint tissue, combined with medium enriched in immunomodulatory factors (among other bioactive factors) produced by umbilical cord stroma-derived MSCs (eUC-MSCs), that nat-urally contribute to suppress the immune rejection in the maternal-fetal barrier. A clinical case of an equine acute desmitis, treated with this formulation is presented. Ultrasonographic ligament regeneration occurred in a reduced time frame, reducing stoppage time and allowing return to unrestricted competition after completion of a physical rehabilitation program. This study fo-cused on the determination of the formulation therapeutic potential and the evaluation of its synergistic effect in an equine desmitis treatment, utilizing the cells themselves and its secretome.

A unique method for synthesizing a surface modifier for metallic hydrogen permeable mem-branes based on non-classic bimetallic pentagonally structured Pd-Pt nanoparticles has been de-veloped. It was found that nanoparticles had unique hollow structure. This significantly reduces the cost of their production due to economical use of metal. According to the results of electro-chemical studies, synthesized bimetallic Pd-Pt/Pd-Ag modifier showed excellent catalytic activi-ty (up to 60.72 mA cm–2), long-term stability and resistance to COads poisoning in alkaline oxida-tion reaction of methanol. The membrane with pentagonally structured Pd-Pt/Pd-Ag modifier showed the highest hydrogen permeation flux density up to 27.3 mmol s–1 m–2. Obtained hy-drogen flux density were 2 times higher than that for membranes with classic Pdblack/Pd-Ag modifier and an order of magnitude higher than that for unmodified membrane. Since the rate of transcrystalline hydrogen transfer through a membrane increased, while the speed of transfer through defects remained unchanged, a one and a half times rise in selectivity of the developed Pd-Pt/Pd-Ag membranes was recorded and it amounted to 3514. Achieved results are due to both the synergistic effect of the combination of Pd and Pt metals in the modifier composition and the large number of available catalytically active centers, which are present as a result of non-classic morphology with high-index facets. The specific faceting, defect structure and unusual properties provide great opportunities for the application of nanoparticles in the areas of membrane reac-tors, electrocatalysis, petrochemical and hydrogen industries.

In our previous work, we demonstrated the potential of the amphiphilic cyclic peptide [W4R4] as a promising antimicrobial agent. The extensive data accumulated on the antimicrobial activity of this peptide and its homologs presented an opportunity to unravel the molecular mechanisms governing their action and establish crucial structure-activity relationships (SAR). To achieve this, we employed a comprehensive approach involving peptide synthesis, in vitro biological testing, and molecular modeling to systematically analyze the SAR of a series of cyclic peptides derived from the [W4R4] scaffold. Minimal modifications were introduced to the original peptide by incorporating either one aromatic hydrophobic residue (W) or one polar positively charged residue (R) while maintaining the sequential W/R arrangement. Additionally, we introduced an "intermediate" substitution by incorporating 2,5-diketopiperazine (DKP), possessing both aromatic and polar properties, into the macrocycle [W4R4] between the W and R residues. Notably, this study marked the first synthesis and evaluation of the [W4R4(DKP)] peptide. Structural, dynamic, hydrophobic, and membrane-binding properties of four cyclic peptides ([W4R4], [W5R4], [W4R5], [W4R4(DKP)]) were explored using molecular dynamics simulations within a DOPC/DOPG lipid bilayer that mimics the bacterial membrane. The results obtained revealed distinct SAR profiles for all peptides, enabling the establishment of correlations between their antimicrobial activity and structural/dynamic parameters. These parameters included the degree of conformational plasticity, the depth of immersion into the bi-layer, and the population of the membrane binding mode characterized by the embedding of the hydrophobic peptide pattern into the acyl chain region of lipids. In particular, the peptide [W4R5] exhibited an optimal "activity/binding to the bacterial membrane" pattern. This work highlights the significance of our multidisciplinary approach in efficiently deciphering finely regulated SAR profiles for a series of homologous peptides with diverse activities. Furthermore, this research provides a solid foundation for the rational design of novel antimicrobial peptides.

Tissue regeneration is an essential requirement for wound healing and recovery of organs’ function. It has been demonstrated that wound healing can be facilitated by activating paracrine signaling mediated by exosomes secreted from stem cells, since exosomes deliver many functional molecules including growth factors (GFs) and neurotrophic factors (NFs) effective for tissue regeneration. In this study, an exosome-rich conditioned medium (ERCM) was collected from human amniotic membrane stem cells (AMSCs) by cultivating the cells under a low oxygen tension (2% O2 and 5% CO2). The contents of GFs and NFs including keratinocyte growth factor, epidermal growth factor, fibroblast growth factor 1, transforming growth factor-β, and vascular endothelial growth factor responsible for skin regeneration were much higher (10-30 folds) in the ERCM than in normal conditioned medium (NCM). In was found that CM-DiI-labeled exosomes readily entered keratinocytes and fibroblasts, and that ERCM not only facilitated the proliferation of keratinocytes in normal condition, but also protected against H2O2 cytotoxicity. In cell-migration assay, the scratch wound in keratinocyte culture dish was rapidly closed by treatment with ERCM. Such wound-healing effects of ERCM were confirmed in a rat whole skin-excision model: i.e., the wound closure was significantly accelerated, remaining minimal crusts, by topical application of ERCM solution (4 x 109 exosome particles/100 μL) at 4-day intervals. In the wounded skin, the deposition of collagens was enhanced by treatment with ERCM, which was supported by the increased production of collagen-1 and collagen-3. In addition, enhanced angiogenesis in ERCM-treated wounds was confirmed by increased von Willebrand factor (vWF)-positive endothelial cells. The results indicate that ERCM from AMSCs with high concentrations of GFs and NFs improves wound healing through tissue regeneration not only by facilitating keratinocyte proliferation for skin repair, but also activating fibroblasts for extracellular matrix production, in addition to the regulation of angiogenesis and scar tissue formation.

At the molecular level, aging is often accompanied by dysfunction of stress-induced membrane-less organelles (MLOs) and changes in their material state. In this work, we analyzed the proteins included in the proteome of stress granules (SGs) and P-bodies for their tendency to transform the material state of these MLOs. Particular attention was paid to proteins whose gene expression changes during replicative aging. It was shown that the proteome of the studied MLOs practically does not differ in the analyzed characteristics and consists of completely or partially intrinsically disordered proteins, 30 - 40% of which are potentially capable of liquid-liquid phase separation (LLPS). At the same time, the proportion of proteins capable of spontaneous LLPS is relatively small, which indicates the leading role of nucleic acids in the biogenesis of these membrane-less organelles. Proteins whose gene expression changes during the transition of human cells to a senescent state make up about 20% of the studied proteomes. There is a statistically significant increase in the number of positively charged proteins in both datasets studied compared to the complete proteomes of these organelles. An increase in the relative content of DNA-, but not RNA-binding proteins, was also found in the stress-granules dataset with senescence-related processes. Among SG proteins potentially involved in senescent processes, there is an increase in the abundance of potentially amyloidogenic proteins compared to the whole proteome. The hnRPDL protein has the highest degree of disorder and highest propensity for LLPS among such proteins, which allows us to consider it as “potentially dangerous.” Proteins common to SGs and P bodies, potentially involved in processes associated with senescence, form clusters of interacting proteins. The largest cluster is represented by RNA-binding proteins involved in RNA processing and translation regulation. These data indicate that SG proteins, but not proteins of P-bodies, are more likely to transform the material state of MLOs. Furthermore, these MLOs can participate in processes associated with aging in a coordinated manner.

The regulation of intracellular pH in yeast (Saccharomyces cerevisiae) cells is critical for cell function and viability. In yeast, protons (H+) can be excreted from cell by the plasma membrane ATPase Pma1 and pumped into vacuoles by the vacuolar H+-ATPase. Because Pma1 is critical to the survival of yeast cells, it is unknown whether other compensatory components are involved in the pH homeostasis in the absence of Pma1. To elucidate how intracellular pH is regulated independently of Pma1, we employed a screening approach by exposing the yeast haploid deletion mutant library (ver 4.0) to the selective plant plasma membrane H+-ATPase inhibitor PS-1, which we previously reported. After repeated screenings and verification, we identified two proteins, ALY1 and ALY2, that play a role in the regulation of intracellular pH when Pma1 is deficient. Our research uncovers a new perspective on the regulation of intracellular pH related to Pma1 and also preliminarily reveals a role for ALY1 and ALY2 in the regulation of intracellular pH.

Dysferlinopathies comprise a spectrum of muscular dystrophies characterized by progressive muscle weakness and degeneration due to mutations in the DYSF gene, which encodes the dysferlin protein critical for muscle membrane repair. This review delves into the clinical spectra of dysferlinopathies, their molecular mechanisms, and the spectrum of emerging therapeutic strategies. We explore the phenotypic heterogeneity of dysferlinopathies, highlight the incomplete understanding of genotype-phenotype correlations, and discuss the implications of various DYSF mutations. Furthermore, we examine the utility of animal models in elucidating disease mechanisms and the potential of symptomatic, pharmacological, molecular, and genetic therapies in mitigating the disease's progression. We also consider the roles of diet and metabolism in managing dysferlinopathies, as well as the impact of clinical trials on treatment paradigms. By culminating the complexities inherent in dysferlinopathies, this article emphasizes the need for multidisciplinary approaches, precision medicine, and extensive collaboration in research and clinical trial design to advance our understanding and treatment of these challenging disorders.

The increase in fungal infections, accompanied by adverse effects and acquired resistance associated with the use of antifungal agents used for their clinical management, have facilitated the search for new substances with antifungal properties. Naphthoquinones have been investigated due to their multiple biological activities, including their significant antifungal potential. This study aimed at evaluating the antifungal potential of naphthoquinones against opportunistic fungi and dermatophytes and to assess the impact of a selected naphthoquinone on the formation of the cell wall, ergosterol membrane, and cellular membrane of Candida albicans ATCC 60193. Additionally, cytotoxicity in the MRC-(Medical Research Council-)5 cell lineage, Artemia salina, and tomato as well as arugula seeds was evaluated. The antifungal activity of four naphthoquinones was assessed using well-characterized fungal strains, the minimum inhibitory concentration (MIC) was determined applying the microdilution assay technique. Antifungal activity of the assessed naphthoquinones could be confirmed, particularly for 2,3-DBNQ (2,3-dibromo-1,4-naphthoquinone), which showed prominent antifungal activity (MIC of <1.56 - 6.25 µg/mL) in all chosen test settings. However, its toxicity in MRC-5 cells (IC50 = 15.44 µM), a recorded 100% mortality in A. salina at a concentration of 50 µg/mL, as well as inhibition of 94.8% of the tomato seeds at a concentration of 400 µg/mL and inhibition of 64.1% of arugula seeds at a concentration of 200 µg/mL may limit hypothetical therapeutic applications. It was demonstrated that the likely mechanism of action of 2,3-DBNQ involves interfering with fungal membrane permeability, leading to increased leakage of nucleotides. This study adds to available knowledge on antifungal effects of naphthoquinones, especially of 2,3-DBNQ, against opportunistic yeasts and dermatophytes. However, the observed cytotoxicity in the MRC-5 cell lineage, A. salina, as well as tomato and arugula seeds highlights a need for further research to optimize the selectivity and safety profile of naphthoquinones like 2,3-DBNQ before potential clinical use may be assessed.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

We consider subtleties of the horizon (null-hypersurface) limit in the Parikh-Wilczek Membrane Approach to Black Holes. Specifically, we refine the correspondence between the (projected) Einstein equations of gravity with matter and the Raychaudhuri-Damour-Navier-Stokes (RDNS) equations of relativistic hydrodynamics. For a general configuration of gravity with matter we obtain additional terms in the hydrodynamic equations, which include logarithmic derivarives of a parameter (the regularization function) determining the proximity of a stretched membrane to the BH horizon. Direct computation of the new terms for exact (Schwarzschild and Kerr) solutions to the Einstein equations results in vanishing the additions to the RDNS equations in the horizon limit. For spacetimes, which are not exact solutions to the Einstein equations, as, for instance, for space-time configurations mimicking black holes, taking into account new terms in the RDNS equations is the mandatory operation. We also comment the correspondence between the horizon limit of the Parikh-Wilczek Membrane Approach and the Gourgoulhon-Jaramillo method of a null-hypersurface description, as well as the link of the obtained results to our previous work on the Kerr black holes.

This paper describes new horizons in the diversity and taxonomy of negev-like viruses encoding the membrane-embedded SP24 protein. First, our data extend the known host range of SP24-encoding negev-like viruses to include brown algae, fungi, green plants, the phylum Entoprocta, the phylum Mollusca, and vertebrates. Second, our phylogenetic analysis suggests that the evolution of the SP24 gene family may have involved frequent events of inter-order virus genome shuffling. Third, the identification of 2-3 copies of SP24 protein genes in some virus RNAs shows that virus genomes may have acquired additional SP24 genes during the evolutionary process due to duplications or new acquisition steps. Forth, the broad host specificity of some SP24-encoded viruses may be related to an important adaptive role of SP24. Fifth, insect and nematode genomes may acquire viral SP24 genes by putative horizontal transfer from negev-like viruses known to infect species of both taxa.

This study focused on the precise detection and concordant analysis of circulating tumor cells (CTCs) to verify the usefulness of CTCs as promising clinical markers. CTCs are traditionally achieved using immune-fluorescence and morphological techniques. By combining two prostate cancer-specific genes (PSA and PSMA) and two epithelial-specific genes (EpCAM and KRT19), the CTC detection efficiency can be enhanced. The detection rates of localized prostate cancer (LPC), locally advanced prostate cancer (LAPC), metastatic hormone-sensitive prostate cancer (mHSPC), and metastatic castration-resistive prostate cancer (mCRPC) were 63.04 % (29/46), 70.59% (34/51), 94.34% (50/53), and 90% (126/140), respectively. Subsequent correlation analysis between the four genes, baseline PSA, and CTC count revealed that only the CTC count correlated with baseline PSA in the localized stages of prostate cancer, whereas all four genes were correlated with baseline PSA and CTC count in the metastatic stages of prostate cancer. The precise detection of CTCs using both numerical and transcriptomic analyses can improve the accuracy of biomarker investigations. This study provides valuable insights into the limitations of serum PSA testing and offers a promising alternative to diagnose and manage prostate cancer via the CTC number and specific genes for prostate cancer.

N-maleimide-derivatized phospholipids are often used to facilitate protein anchoring to membranes. In autophagy studies, this is applied to the covalent binding of Atg8, an autophagy protein, to a phosphatidylethanolamine (PE) in the nascent autophagosome. However, the question remains on how closely the N-maleimide PE derivative (PE-mal) mimicks the native PE in the bilayer. In the present paper, spectroscopic and calorimetric techniques have been applied to vesicles containing either PE or PE-mal (together with other phospholipids) to compare the properties of the native and derivatized forms of PE. According to differential scanning calorimetry, and to infrared spectroscopy, the presence of PE-mal did not perturb the fatty acyl chains in the bilayer. Fluorescence spectroscopy and microscopy showed that PE-mal did not alter bilayer permeability either. However, fluorescence emission polarization of Laurdan and DPH probes indicated an increased order, or decreased fluidity, in the bilayers containing PE-mal. In addition, infrared spectral data from the phospholipid phosphate region revealed a PE-mal-induced conformational change of the polar heads, accompanied by an increased hydration. Globally considered, the results suggest that PE-mal would be a reasonable substitute for PE in model membranes containing reconstituted proteins.

The formation and functioning of membrane-less organelles (MLOs) is one of the main driving forces in the molecular life of the cell. These processes are based on the separation of biopolymers into phases regulated by multiple specific and nonspecific inter- and intramolecular interactions. Among the realm of MLOs, a special place is taken by the promyelocytic leukemia nuclear bodies (PML-NBs or PML bodies), which are the intranuclear compartments involved in the regulation of cellular metabolism, transcription, maintenance of genome stability, response to viral infection, apoptosis, and tumor suppression. According to the accepted models, specific interactions, such as SUMO/SIM, formation of disulfide bonds, etc., play a decisive role in the biogenesis of PML bodies. In this work, a number of bioinformatics approaches were used to study proteins found in the proteome of PML-bodies for their tendency to spontaneous liquid-liquid phase separation (LLPS), which is usually caused by weak nonspecific interactions. 205 proteins found in PML bodies have been identified. It has been suggested that UBC9, P53, HIPK2, and SUMO1 can be considered as the scaffold proteins of PML bodies. It was shown that more than half of the proteins in the analyzed proteome are capable of spontaneous LLPS, with 85% of the analyzed proteins being intrinsically disordered proteins (IDPs), and remaining 15% being proteins with intrinsically disordered protein regions (IDPRs). About 44% of all proteins analyzed in this study contain SUMO binding sites and can potentially be SOMYylated. These data suggest that weak nonspecific interactions play a significantly larger role in the formation and biogenesis of PML bodies than previously expected.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na2O: 1Al2O3: 19 SiO2: 5000H2O, the effects of synthesis temperature, crystallization time, and porous support (α-Al2O3 or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al2O3 support at 368 K for 8 h, and had good reproducibility. The H2 permeance of the membrane was as high as 5.34×10-7 mol/(m2 s Pa), and the H2/C3H8 and H2/i-C4H10 selectivities were 183 and 315, respectively. The C3H6/C3H8 selectivity of the membrane was as high as 46 with a remarkably high C3H6 permeance of 1.35× 10-7 mol/(m2 s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and relatively wide pore size (0.74 nm).

membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic hydrophobic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

Extracorporeal membrane oxygenation (ECMO) is used for the management of severe respiratory and cardiac failure, as well as bridge to definite treatment or transplantation. ECMO associated coagulopathy (EAC) is a frequent complication leading to high rates of thrombosis or severe haemorrhage, contributing to morbidity and mortality of patients. Understanding the pathophysiology of EAC is substantial for effectively managing patients on ECMO. We analyse the underlying mechanism of EAC and discuss the monitoring of coagulation profile, combining the viscoelastic point of care assays with the conventional coagulation laboratory tests.

(1) Background: The Gárdos channel (KCNN4) and Piezo1 are the best-known ion channels in the red blood cell (RBC) membrane. Nevertheless, the quantitative electrophysiological behavior of RBCs and its heterogeneity are still not completely understood.; (2) Methods: Here we use state-of-the-art biochemical methods to probe for the abundance of the channels in RBCs. Furthermore, we utilize automated patch-clamp, based on planar chips, to compare the activity of the two channels in reticulocytes and mature RBCs. Besides this characterization, we performed membrane potential measurements to demonstrate the effect of channel activity and interplay on the RBC properties.; (3) Results: Both, Gárdos channel and Piezo1, albeit their average copy number of activatable channels per cell is in the single digit range, can be detected by transcriptome analysis of reticulocytes. Proteomics analysis of RBCs could only detect Piezo1 but not the Gárdos channel. Furthermore, they can be reliably measured in the whole-cell configuration of the patch-clamp method. While for the Gárdos channel the activity is higher in reticulocytes compared to mature RBCs, for Piezo1 the tendency is the opposite. While the interplay between Piezo1 and Gárdos channel cannot be followed using the patch-clamp measurements, it could be proved based on membrane potential measurements in populations of intact RBCs.; (4) Conclusions: We discuss the Gárdos channel and Piezo1 abundance, interdependencies and interactions in the context of their proposed physiological and pathophysiological functions, which are the passing of small constrictions, e.g., in the spleen, and their active participation in blood clot formation and thrombosis.

Abstract: membrane separation technology shows promise, particularly gas separation membranes, including ceramic membrane. Ceramic membranes are increasingly gaining attention for their acid and alkali stability, corrosion resistance, high-temperature tolerance, and mechanical strength. This study focuses on alumina support ceramic membrane for CO2 capture. The membranes were characterized using contact angle measurements, scanning electron microscopy (SEM), and Fourier Transform Infrared spectroscopy (FTIR) analysis. The contact angle measurements confirmed the hydrophilic, while SEM analysis showed even particle distribution in the alumina ceramic membranes respectively. EDAX analysis revealed the elemental composition in the alumina support matrix. FTIR analysis demonstrated chemical interactions of the support membrane. Single gas permeation experiments were conducted. It can be observed that Nitrogen gas permeated faster with increase in feed pressure through the unmodified ceramic inorganic membrane more than the other two single gases, O2, and CO2). As a result, only high permeance separation membranes with realistic size and pressure conditions may be considered of as a practical alternative for CO2 capture. However, the presence of non-selective defects limited the improvement in selectivity of hydrophilic ceramic membrane. In this case, there is need to modify the ceramic membrane used to increase the flux, permeance of CO2, and selectivity of CO2.

The generation and maintenance of membrane potential is considered a fundamental element of the cellular machinery. They are based on elements of physics and chemistry. Mathematics is used to validate the equations and evaluate the results. However, this computation process can lead to a misunderstanding of the phenomena involved or to the masking of crucial events. It is even possible that the calculation no longer corresponds to the hypothesis considered. Membrane theory is no exception to these trivial considerations, which are essential for normal theory validation.

Composite polymolecular separation membranes were prepared by combining multi-branched ZIF-L with high porosity electrospinning nanofibers PI. Meanwhile, PDA and PEI were introduced into the membrane in order to improve its adhesion. The new membrane is so called “PI@PDA@PEI/ZIF-L-4” composite membrane; compared with PI@PDA@PEI/ZIF-8 composite membrane, the new membrane’s filtration rates for heavy metal ions such as Cd2+, Cr3+ and Pb2+ were increased by 7.0%, 6.6% and 9.3%, respectively. Furthermore, the new membrane has a permeability up to 1,140.0 L·m−2·h−1·bar−1, and were presenting a very stable performances after four repeated uses. The separation mechanism of PI@PDA@PEI/ZIF-L composite membranes was further analyzed in order to provide a base support for producing separation membranes with high barrier rate and high flux.

This work presents the possibility of using a synthetic membrane for pretracing mucosal penetration studies. The permeability of two types of membranes, porcine oral mucosa and a synthetic Nuclepore membrane, to water was compared. Moreover, the water permeability of membranes modified with waterproofing formulations was measured to study their ability to protect against the penetration of viruses, toxins, etc. A very good correlation was obtained between the transmucosal water loss (TMWL) values of the artificial membrane and the mucosa. These results support the possible use of this synthetic membrane in the screening of the water permeability of formulations. In addition, studies of the permeation of different actives, drugs and biocides through the two membranes were carried out, and these results were compared with their skin permeation data. The synthetic membrane does not seem to discern between compounds in terms of permeability, which could be due to the lack of lipids in the composition of this synthetic membrane. Therefore, Nuclepore alone cannot be used as a model for the release of actives. Additionally, the permeation of caffeine through intact or modified membranes incorporating waterproofing formulations was also studied. In this case, similar permeation profiles through the synthetic membrane and mucosa were found. The results from these assays should lend support to the use of this synthetic membrane when screening formulations to be applied in oral penetration studies.

Angiogenesis is a process whereby new blood vessels are born from preexistent ones, which has a role in transporting oxygen and nutrients. On the other hand, inhibiting this process is a strategy used to treat some diseases, including cancers, diabetic retinopathy, and rheumatoid arthritis. This study investigates the effect of a new nutraceutical (Terasen®) on angiogenesis. Terasen® is made from a standardized extract of Euterpe oleraceae (Açaí), Myrciaria dubia (Camu-Camu), and purified oil of Bixa orellana (Annatto) and Astrocaryum aculeatum (Tucumã). The in vivo angiogenesis model used was the chorioallantoic membrane (CAM) from chicken embryos. The embryos were divided into seven groups: a vehicle control treated with ethanol solution (ETH), a naïve control treated only with saline solution (SOR), a positive control treated with dexamethasone (DEX), and four groups treated with Terasen® at different concentrations (0.5, 1, 2, and 3 mg/ml). The parameters assessed were the vessels’ area, length, and amount. The results show a statistically significant and concentration-dependent inhibition of angiogenesis caused by Terasen®. Our results suggest the nutraceutical has a high antiangiogenesis potential, possibly due to its bioactive compounds, including anthocyanins, quercetin, and tocotrienols.

Needle abscission in balsam fir has been linked to both cold acclimation and changes in lipid composition. The overall objective of this research is to uncover lipid changes in balsam fir during cold acclimation and link those changes with postharvest abscission. Branches were collected monthly from September to December and assessed for cold tolerance via membrane leakage and chlorophyll fluorescence changes at -5, -15, -25, -35, and -45°C. Lipids were extracted and analyzed using mass spectrometry while postharvest needle abscission was determined gravimetrically. Cold tolerance and needle retention each significantly (P < 0.001) improved throughout autumn in balsam fir. There were concurrent increases in DGDG, PC, PG, PE, and PA throughout autumn and a decrease in MGDG. Those same lipids were strongly related to cold tolerance, though MGDG had the strongest relationship (R2 = 55.0% and 42.7% from membrane injury and chlorophyll fluorescence, respectively). There was a similar, albeit weaker, relationship between MGDG:DGDG and needle retention (R2 = 24.3%). Generally, a decrease in MGDG:DGDG ratio resulted in better cold tolerance and higher needle retention in balsam fir possibly due to increased membrane stability.

The current view of the mitochondrial respiratory chain complexes I, III and IV foresees the oc-currence of their assembly in supercomplexes providing additional functional properties as compared with randomly colliding isolated complexes. According to the plasticity model, these two structural states of the respiratory chain may interconvert influenced by the intracellular prevailing conditions and in previous studies we candidated the mitochondrial membrane po-tential as a factor controlling their dynamic balance. Here, we extended those studies investigating if and how the cAMP/PKA-mediated signalling influences the aggregation state of the respiratory complexes. Analysis of inhibitory-titration profiles of the endogenous oxygen consumption rates in intact HepG2 cells with specific inhibitors of the respiratory complexes was performed to quantify, in the framework of the metabolic flux theory, the corresponding control coefficients. The results attained inhibiting pharmacologically either PKA and sAC indicate that the reversible phosphorylation of the respiratory chain complexes/supercomplexes influences their assembly state in response to the membrane potential. This conclusion is supported by scrutiny of the available structure of the CI,CIII2,CIV respirasome enabling to map several PKA-target serine residues exposed to the matrix side of the complexes I, III and IV at the contact interfaces of the three complexes.

It is important to develop new antibacterial drugs since the emergence of bacterial resistance to available antibiotics. Metal nanoparticles have the potential to combat antibiotic resistance and are effective antibacterial agents. Here, we demonstrate the biogenic production of zinc nanoparticles using Rhododendron arboreum stem bark. The biosynthesized ZnNPs were characterized through different analytical techniques such as UV-vis, FTIR, EDX, SEM, and XRD. Clinical isolates such as E. coli, S. aureus, and K. pneumonia were used to check the antibacterial efficacy of the biosynthesized zinc nanoparticles. The MIC and MBC values against K. pneumonia, S. aureu, and E. coli were found to be 34±0.21 and 11.71±0.47, 47±0.11 and 23.86±0.84 and 94±0.18 and 40.43±0.16 µg/mL, respectively. It dramatically decreased the integrity of the cell membrane and markedly increased the permeability of both inner and outer membranes. The green synthesized ZnNPs have good catalytic activity. It degraded 65% of methyl orange dye within 6h when the mixture was kept in direct sunlight, thus demonstrating good photodegradation potential and can be employed as a good photocatalyst. According to these results, biosynthesized zinc nanoparticles could be a potential therapy option for controlling bacterial pathogenesis and an effective photocatalyst for the elimination of hazardous water contaminants.

In recent years there has been increasing interest in the discovery of new natural herbal remedies for the treatment of common conditions such as diabetes and inflammatory diseases. In this context, this paper analyzed the antidiabetic and anti-inflammatory potential of two plants of the genus Artemisia: Artemisia absinthium (wormwood) and Artemisia vulgaris (mugwort) and Trigonella foenum-graecum (fenugreek) plants less studied from this point of view. Thus, hydroal-coholic extracts (50% EtOH v/v, 10% mass) were made, which were processed by membrane technologies, micro- and ultrafiltration, in order to concentrate the biologically active principles. The extracts were then analyzed in terms of content in active principles of interest (polyphenols, flavones). The antidiabetic activity of the extracts was analyzed by testing their ability to inhibit α-amylase and α-glucosidase and the anti-inflammatory activity by testing the ability to inhibit hyaluronidase (HYA) and lipoxygenase (LOX). Thus, the T. foenum-graecum extracts showed a high inhibitory activity on α-amylase 3.22 ± 0.3 g / mL (compared to the standard used - IC50 acarbose = 3.5 g / mL) and a high inhibitory activity on LOX: 19.69 ± 0.52 g/mL (compared to all standards used). The concentrated extract of Artemisia vulgaris showed increased activity of inhibition of α-amylase - IC50 = 8.57 ± 2.31g/mL and moderate activity of inhibition of HYA - IC50 = 17.18 g/mL compared to ibuprofen, the standard used - IC50 = 5.73 g/mL. The concentrated extract of Artemisia absinthium showed a pronounced activity of inhibition of LOX - IC50 = 19.71 g / mL, compared to the standard - rutin - IC50 = 22.34 g/mL).

Membrane potential generation and maintenance are fundamental parts of membrane theory. However, since its inception, theories and assumptions have remained simple, whereas the amount of knowledge available has only grown. Unfortunately, this simplification and reductionism lead to its loss of validity on both microscopic and macroscopic scales. This article shows that assumptions made outside the context of factual reality lead to contradictions that cannot be compared with science. Membrane theory must be thoroughly revised, taking into account all forgotten and unanswered assumptions and questions to conform to facts and science to maintain credibility.

This study continued the analysis of immunization with the receptor binding domain (RBD) associated with the adjuvants Dimethyldioctadecylammonium bromide (DDA) and Saponin (Sap) (RBD+DDA/Sap) or Aluminum hydroxide (AH) and outer membrane vesicles (OMVs) of Neisseria meningitidis (RBD+AH/OMV); from adult to old age and assessed maternal-fetal transference of antibodies. Outbred Swiss mice were immunized with 2 intramuscular (IM) doses with the antigenic preparations RBD+DDA/Sap, RBD+AH/OMV or RBD alone. The humoral immune response was evaluated using ELISA, avidity-ELISA, Immunoblotting and a Omicron-surrogate-neutralization assay (BA.1), while the cellular immune response was analyzed by ELISpot. Our previous work studied the IgG response; here, we verified that IgM levels were higher right after the immunization doses, but, as IgG, it persisted until 368 days after the immunization. The avidity of IgM increased from low to intermediate-to-high after the booster dose. RBD+DDA/Sap presented neutralizing indexes against Omicron at days 47 and 176, while RBD+AH/OMV showed neutralization on days 21, 47 and 176. Cellular response, measured 465 days after immunization, revealed IFN-Y and IL-4 secretion. The offspring of RBD+DDA/Sap had detectable antibodies, which decreased around 45 days after birth, the last point we analyzed. The results suggested that DDA/Sap is a promising adjuvant mixture to enhance humoral and cellular immune response against SARS-CoV-2, improving maternal-fetal transference of antibodies; cross-reactivity with Omicron variant; and the maintenance of antibodies for a long period.

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited high water swelling capacity, fast water absorption and high water vapor transmission. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. The drug release kinetics was comparable to that of a commercial PHMB-releasing AMD assayed under the same conditions. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds, and blood clotting activity. The obtained results suggest that these membranes may be suitable for use in the development of AMDs.

Single-particle cryo-electron microscopy (cryo-EM SPA) has recently emerged as an exceptionally well-suited technique for determining the structure of membrane proteins (MPs). Indeed, in the last years, it was observed a huge increase in the number of MPs solved by cryo-EM SPA at a resolution better than 3.0 Å in the Protein Data Bank (PDB). However, sample preparation remains a significant challenge in the field. Here, we evaluated in the MPs solved by cryo-EM SPA deposited in the PDB in the last two years at a resolution below 3.0 Å the most critical parameters for sample preparation: i) the surfactant used for protein extraction from the membrane, ii) the surfactant, amphiphiles, nanodiscs or other molecules present in the vitrification step, iii) the vitrification method employed, and iv) the type of grids used. The aim is not to provide a definitive answer on the optimal sample conditions for cryo-EM SPA of MPs, but rather assess the current trends in the MP structural biology community towards obtaining high-resolution cryo-EM structures.

Nuclear fusion is essential for the sexual reproduction of various organisms, including plants, animals, and fungi. During the life cycle of flowering plants, nuclear fusion occurs three times: once during female gametogenesis and twice during double fertilization, when two sperm cells fertilize the egg and the central cell. Haploid nuclei migrate in an actin filament-dependent manner to become in close contact, then two nuclei fuse. The nuclear fusion process in plant reproduction is achieved by the sequential nuclear membrane fusion events. Recent molecular genetic analyses using Arabidopsis thaliana showed the conservation of nuclear membrane fusion machinery between plants and the budding yeast Saccharomyces cerevisiae. These include the heat shock protein 70 in the endoplasmic reticulum and conserved nuclear membrane proteins. Analyses of A. thaliana mutants of these components show that completion of the sperm nuclear fusion at fertilization is essential for proper embryo and endosperm development.

Indoleamine 2,3-dioxygenase 2 (IDO2) is a paralogue of IDO1, a tryptophan-degrading enzyme producing immunomodulatory molecules. However, the two proteins are unlikely to carry out the same functions. IDO2 shows little or no tryptophan catabolic activity and exerts contrasting immunomodulatory roles in a context-dependent manner, in both cancer and autoimmune diseases. The recently described potential non-enzymatic activity of IDO2 has suggested its possible involvement in alternative pathways resulting in either pro- or anti-inflammatory effects in different models. In a previous study on non-small cell lung cancer (NSCLC) tissues, we found that IDO2 expression, revealed at the plasma membrane level of tumor cells, was significantly associated with poor prognosis. In this study, the A549 human cell line, basally expressing IDO2, was used as an in vitro model of human lung adenocarcinoma to gain more insights on a possible alternative function of IDO2, different from the catalytic one. In these cells, immunocytochemistry and isopycnic sucrose gradient analyses confirmed the IDO2 protein localization in the cell membrane compartment, and immunoprecipitation of tyrosine-phosphorylated proteins revealed that IDO2 can be targeted by kinase activities. The different localization than the cytosolic one and the phosphorylation state are the first indications for the signaling function of IDO2, suggesting that the IDO2 non-enzymatic role in cancer cells is worthy of deeper understanding.

Horses are high performance athletes prone to sportive injuries such as tendonitis and desmitis. Fibrous tissue formation with loss of mechanical properties occurs in tendon repair, becoming a therapeutic challenge to overcome. This impels regenerative medicine to develop innovative therapies that enhance tissue regeneration retrieving original tissue properties. Mesenchymal stem cells (MSCs) have been successfully used to develop therapeutic products. They secrete a variety of bioactive molecules that play a pivotal role in tissue regeneration. These factors are released in culture media producing conditioned media (CM). The aforementioned assumptions impelled us to formulate equine synovial membrane stem cells (eSM-MSCs) – the cellular pool that naturally regenerates joint tissue, combined with medium enriched in immunomodulatory factors produced by umbilical cord stroma-derived MSCs (eUC-MSCs), that naturally contribute to suppress the immune rejection in the maternal-fetal frontier. A clinical case of an equine acute desmitis, treated with the abovementioned formulation is presented. Ligament regeneration occurred in a reduced time frame, reducing stoppage time, allowing return to unrestricted competition after completion of a physical rehabilitation program. This study focus was determination of the formulation therapeutic potential and the evaluation of its synergistic effect in an equine desmitis treatment, utilizing the cells themselves and its secretome.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

Endothelial cells are the crucial inner lining of blood vessels, pivotal in vascular homeostasis and integrity. However, these cells are perpetually subjected to a myriad of mechanical, chemical, and biological stresses that can compromise their plasma membranes. A sophisticated repair system involving key molecules, such as calcium, annexins, dysferlin, and MG53, is essential for maintaining endothelial viability. These components orchestrate complex mechanisms, including exocytosis and endocytosis, to repair membrane disruptions. Dysfunctions in this repair machinery, often exacerbated by aging, are linked to endothelial cell death, subsequently contributing to the onset of atherosclerosis and the progression of cardiovascular diseases (CVD) and stroke, major causes of mortality in the United States. Thus, identifying the core machinery for endothelial cell membrane repair is critically important for understanding the pathogenesis of CVD and stroke and developing novel therapeutic strategies for combating CVD and stroke. This review summarizes the recent advances in understanding the mechanisms of endothelial cell membrane repair. The future directions of this research area are also highlighted.

Public health suffers from noxious gas of beached Sargassum algae. Floating barrages containing them at sea will be useful provided efficiently catch them and resist to hydrodynamic pressure. Nowadays design and installation of algae barrages are empiric. Structural break, anchor and mooring chain drifts can arise. We provide a mechanical model to evaluate stresses and loads on a structure made of nets and moorings. Hydrodynamic uncertainties occur through catches, fouling, and a range of sea currents appearing in lagoons or sheltered bays. We consider a nonlinear finite-element model of elastic membrane in large displacements and small strains. We study some forcings fixed a priori on a standard section of barrage. A section 50 m long, 1 m high, with two net-faces is examined at low and moderate current velocities, 0.05 and 0.35 m.s-1, while assuming specific vertical and horizontal catch pressures. A barrage installed in lagoon at Le François on Martinique Island and being observable by satellite imagery could benefit of the computed net and mooring tensions.

The possibility of deep radiochemical purification of Li2CO3 has been examined in the frame of the purification program of AMoRE collaboration. In this experiment, commercial Li2CO3 was converted into LiNO3. Co-precipitation with inorganic salt-based carriers followed by membrane filtration and sorption using MDM inorganic sorbent methods were tested for the removal of alkaline-earth and transition metals, potassium, magnesium, aluminum, uranium, thorium, and radium. The calcium molybdate-based carrier was the most efficient for removing Th, U, and K. Subsequently, the radium, calcium, and barium contaminations were removed with MDM sorbent. After the impurities’ removal, the final Li2CO3 product was synthesized with NH4HCO3 sludge. The separation factors were derived by means of ICP-MS and HPGe analyses of the initial material, intermediate and final products. The study showed the optimum conditions of co-precipitation and sorption to reach a high yield and radiopurity of lithium carbonate used for low radioactive background experiments.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

Maxillary sinus augmentation with a lateral approach (MSA) is a well-established treatment. In this prospective study, we evaluated risk factors for postoperative bone-graft displacement and report the clinical application of long-term resorbable GMEM-B-2 (L-lactic acid/-caprolactone [P(LA/CL)]) as a barrier membrane to cover the open window in the lateral wall in MSA. Twenty-four patients underwent MSA according to the relevant criteria; CT data obtained before and 1 week (1W) and 5–6 months (5M) post-MSA, bone height changes, bone height reduction rates at 1W and 5M post-MSA, bone-graft displacement measurements, and risk factors were examined. All patients showed bone height increments (p &lt; 0.005). However, no difference was observed between 1W and 5M post-MSA. Bone-graft displacement was observed in eight patients; the reduction rate from 1W to 5M post-MSA was 8.38% ± 4.88%. Sex, septa, maxillary sinus floor–palatal bone distance, and maxillary sinus floor–natural mouth distance were associated with bone-graft displacement (p &lt; 0.05). Height from the maxillary sinus floor to the palatal bone and the sinus angle influenced the augmentation amount (p &lt; 0.05). The L-lactic acid/ε-caprolactone [P(LA/CL)] membrane compared favourably with other membranes and may be useful as a barrier membrane for the MSA open window.

As mitochondria are negatively charged organelles, penetrating cations are used as a part of the chimeric molecules to deliver the specific compounds into mitochondria. However, unmodified penetrating cations affect different aspects of cellular physiology as well. In this review we have attempted to summarize the data about side effects of the commonly used natural (e.gberberine) and artificial (e.g. tetraphenylphosphonium, rhodamine, methylene blue) penetrating cations on cellular physiology. For instance, it was shown that such types of molecules can (1) facilitate proton transport across membranes; (2) react with redox groups of respiratory chain; (3) induce DNA damage; (4) interfere with pleiotropic drug resistance; (5) disturb membrane integrity (6) inhibit the enzymes. Also, the products of the biodegradation of penetrating cations can be toxic. As penetrating cations accumulate in mitochondria, their toxicity is mostly due to the mitochondrial damage. Mitochondria of certain types of cancer cells appear to be especially sensitive to penetrating cations. Here we discuss the molecular mechanisms of the toxic effects and the anti-cancer activity of the penetrating cations.

Abstract Aims: In recent years, electro kinetic (EK) remediation has become more popular as a novel method for removing chromium contamination from soil. This approach, however, is ineffective since it uses both cationic and anionic forms of chromium. In this work, a membrane –based technique was employed to increase the efficiency of the electro kinetic removal of chromium. Methods: Chromium removal from polluted sludge was studied in four bench-scale experiments, two of which used distilled water (EK-1, EK2 & Membrane) and two of which used acetic acid as a catholyte (EK-3, EK4 &Membrane). Results: The pH, total chromium, and fractionation of chromium in the sludge were measured after remediation. In the EK-1, EK-2 & Membrane and EK-3, EK-4 & Membrane trials, the average removal efficiency of total chromium was 47.6%, 58.6%, and 74.4%, 79.6%, respectively. Conclusion: In contrast to the electro kinetic remediation strategy, which left approximately 80% of the sludge neutral or alkaline after treatment, the use of the membrane created acidic soil conditions throughout the sludge. For example, the high field intensity used in the membrane tests may have helped to facilitate chromium desorption, dissolution and separation from the sludge, as well as enhance chromium mobility. The findings show that the membrane can improve the effectiveness of chromium removal from sludge when utilized in the EK remediation process.

Milk fat globule membrane (MFGM) is a complex tri-layer membrane that wraps droplets of lipids in milk. In recent years, it has attracted widespread attention due to its excellent bioactive functions and nutritional value. The milk fat globule membrane contains a diverse array of bioactive lipids, including cholesterol, phospholipids, and sphingolipids, which play pivotal roles in mediating the bioactivity of the milk fat globule membrane. We sequentially summarize the main lipid types in milk fat globule membrane in this comprehensive review and outline the characterization methods used to employed them. In this comprehensive review, we sequentially describe the types of major lipids found in the milk fat globule membrane and outline the characterization methods employed to study them. Additionally, we compare the structural disparities among glycerophospholipids, sphingolipids, and gangliosides, while introducing the formation of lipid rafts facilitated by cholesterol. The focus of this review revolves around an extensive evaluation of current research on lipid isolates from the milk fat globule membrane, as well as products containing milk fat globule membrane lipids, with respect to their impact on human health. Notably, we emphasize clinical trials encompassing a large number of participants. The summarized bioactive functions of milk fat globule membrane lipids encompass regulation of human growth and development, influence on intestinal health, inhibition of cholesterol absorption, enhancement of exercise capacity, and anti-cancer effects. By offering a comprehensive overview, the aim of this review is to provide valuable insights into the diverse biologically active functions exhibited by lipids in milk fat globule membrane.

Accumulation of proteins in filter membranes limits the efficiently of filtering technologies for cleaning wastewater. Efforts are ongoing to coat commercial filters with different materials (such as titanium-dioxide, TiO2) in order to reduce the fouling of the membrane. Beyond monitoring the desired effect of retention of biomolecules, it is demanding to understand what are the biophysical changes in water-soluble proteins caused by interacting with the new coated filter membranes, an aspect that has received little attention so far. Using spin label electron paramagnetic resonance (EPR), aided with native fluorescent spectroscopy and dynamic light scattering (DLS), here we report the changes in the structure and dynamics of bovine serum albumin (BSA) exposed to TiO2 (P25) nanoparticles or passing through commercial polyvinylidene fluoride (PVDF) membranes coated with the same nanoparticles. We have found that the filtering process and prolongued exposure to TiO2 nanoparticles had significant effects on different regions of BSA, and denaturation of the protein was not observed, neither with TiO2 nanoparticles nor by pressing through TiO2-coated filter membranes.

This review describes and discusses unusual axonal structural details and evidence for unmasking of sulfhydryl groups (-SH) in axoplasmic membranes resulting from electrical stimulation or asphyxia. Crayfish axons contain fenestrated septa (FS) that in phase contrast micrographs appear as repeated striations. In the electron microscope each septum is made of two cross-sectioned membranes containing ~550 Å pores, each occupied by a microtubule. Thin filaments, likely to be made of kinesin, bridge the microtubule to the edge of the pore. FS are believed to play a role in axoplasmic flow. The axons also display areas in which axon and sheath-glial cell plasma membranes are sharply curved and project into the axoplasm. In freeze-fractures, the protoplasmic leaflet (P-face) of the projections appears as elongated indentations containing parallel chains of particles. The sheath-glial cell plasma membrane also contains particles, but they are irregularly aggregated. The axons also display areas where axonal and glial plasma membranes fuse, creating intercellular pores. In axons fixed during electrical stimulation the plasma membrane, the outer membrane of mitochondria, membranes of other cytoplasmic organelles and gap junctions increase in electron opacity and thickness, resulting from unmasking of sulfhydryl groups (-SH). Similar changes occur in asphyxiated nerve cords.

Insoluble contaminant or a varnish is a result of oil degradation by products and sometimes depleted additive molecules. This process is in most cases initiated by thermal stress placed on the oil. In tribology varnish becomes a significant problem for modern complex machinery lubrication systems as it has severe debilitating effects such as loss of operating clearances and heat transfer. Problems arising from varnish build-up in lubricants can be inhibited by timely oil analysis which gives us important information about oil-degradation level and current insoluble contaminants potential of oil. There are several laboratory testing methods to describe varnish potential. The most applied one is a colorimetric analysis, also known as MPC (Membrane Patch Colorimetry) as it tends to be reasonably quick and cost-effective. This study applies principles generally used for MPC test of turbine oils to measure lubricant generated insoluble contaminants of hydraulic fluids. For this purpose, in-service oil samples were taken from hydraulic circuits of rubber vulcanizing presses and analyzed using testing method based on method defined by standard ASTM D7843 – 21. Accuracy of this testing method is dependent on development time of tested sample. Therefore, we not only try to proof applicability of this method for hydraulic oils but also want to determine incubation time needed for efficient and accurate determination of concentration of insoluble contaminants in the sample.

In a blood purification technique continuous renal replacement therapy called CRRT , a porous hollow-fiber polymeric membrane is exposed to prolonged contact with blood. In that condition, like with any other submerged filtration membrane, hemofilter loses its properties over time and use which results in a rapid decline in flux. The most significant reason for this loss is the formation of a biofilm. Protein, blood cells and bacterial cells attach to the membrane surface in complex and fluctuating processes. Anticoagulation allows for longer patency of vascular access and a longer lifespan of the membrane. Other preventive measures include modification of the membrane itself. In this article, we focused on the role of nanoadditives in the mitigation of bio-fouling. Nanoparticles such as graphene, carbon nanotubes, silica effectively change surface properties towards more hydrophilic, affect pore size and distribution, decrease protein adsorption and damage bacteria cells. As a result, membranes modified with nanoparticles show better flow parameters, longer lifespan and increased hemocompatibility.