This article couples human metabolic factors and heating environmental factors, and uses a 57 node human thermal physiological model to study the heating effect of radiators. It provides a way to objectively calculate and directly quantify the effect of heating equipment on human thermal physiological parameters. As the inlet speed increases, the surface temperature of the human body first increases and then decreases. At a speed of 3m/s, it basically reaches a high value. Continuing to increase the wind speed, as the indoor convection intensity further increases, the surface temperature of the human body will decrease, leading to a decrease in thermal comfort. Compared with floor radiation heating under similar indoor temperature conditions, forced convection radiator heating has similar skin temperatures in various parts of the human body after the indoor design temperature exceeds 20 ℃, and the overall thermal comfort of the two technical solutions is equivalent. Research has shown that the turbulence wind speed of convective radiators should not be too small, with a wind speed range of 2.5m/s to 3m/s. The heating effect of using horizontal air outlet from the lower part of the radiator is better than that of vertical air outlet from the upper part. Convection type radiator heating is more suitable for buildings with rooms that are not too high due to the large indoor temperature gradient.

Human epidermal growth factor receptor 2 (HER2) belongs to the ErbB family, a group of four transmembrane glycoproteins with tyrosine kinase activity, all structurally related to the epidermal growth factor receptor (EGFR). These tyrosine kinases are involved in the transmission of cellular signals controlling normal cell growth and differentiation. If this transmission goes awry, it can lead to dysregulated growth of the cell. HER2 specifically can be implicated in the pathogenesis of at least eight malignancies. HER2 positivity quickly became a well characterized indicator of aggressiveness and poor prognosis, with high rates of disease progression and mortality. After realizing the implication of HER2, it first became investigated as a target for treatment in breast cancer, and later expanded to areas of research in other cancers types. To this day, the most therapeutic advancements of anti-HER2 therapy have been in breast cancer, however, there have been strong advancements made in the incorporation of anti HER2 therapy in other cancer types as well. This comprehensive review dissects HER2 to its core incorporating the most up to date information. The topics touched upon are discussed in detail and up to 200 published sources from the most highly recognized journals have been integrated. The importance of knowing about HER2 is exemplified by the groundbreaking advancements that have been made, and the change in treatment plans it has brought to the oncological world in the last twenty years. Since, its ground breaking discovery there has been significant breakthroughs in knowledge regarding the actual receptor, the receptors biology, its mechanism of action, advancements in tests to detect HER2 and significant strides on how to best incorporate targeted treatment. Due to the success of this field thus far, the review concludes by discussing the future of novel anti-HER2 therapy currently in development that everyone should be aware of.

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

C-peptide is used as a measure of endogenous insulin production. Given that insulin and C-peptide are produced in equal amounts, C-peptide is typically used to differentiate between external and endogenously produced insulin in insulin-treated type 1 diabetes mellitus (T1DM). In a clinical setting, a decline in C-peptide is regarded as a loss of beta cell function. However, physiological conditions may also be associated with low C-peptide levels. The authors of this paper use a low-carbohydrate diet, the so-called paleolithic ketogenic diet (PKD), in the treatment of various conditions and observed that C-peptide is typically low on this diet. In order to characterize C-peptide levels on this diet, we designed a study to retrospectively assess C-peptide levels in 100 non-T1DM subjects. We found that 55% of the subjects had a C-peptide level below the standard reference range. C-peptide levels correlated with glucose levels. A significant correlation was found between C-peptide and age, with younger subjects having lower C-peptide levels. Males also showed lower C-peptide levels than females. Given the increasing number of patients using low-carbohydrate diets worldwide, physicians should be aware of laboratory correlates of low-carbohydrate diets, including low C-peptide levels, most importantly to prevent incorrect T1DM diagnosis.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

Studies at the juncture of development economics and public health host considerable responsibility in addressing inequality and related mental health distress. Mental health care in economically marginalized populations requires depicting the linkages between socioeconomic status and psychological distress. In the present work, a sequential mixed-methods design was used to study 190 people in such communities in India. Gender-dependent psychological distress was found according to Kessler Psychological Distress Scale (K-10) with moderate distress in women (M= 26.30, SD= 9.15) and mild distress in men (M= 21.04, SD= 8.35). Regression analysis indicated that gender significantly predicted psychological distress, followed by age, marital status, and education of the head of the family. The Interpretative Phenomenological Analysis of semi-structured interviews to six women who scored the highest on the distress scale unveiled three master themes: (1) Manifestation of Psychological Distress, (2) Contextual Challenges, and (3) Sources of Strength and Resilience. Overall, participants reported lack of resources, community violence, gender discrimination, and widespread substance use as major contributors to the ongoing distress. These findings can pave the way for future studies to expand beyond independent economic indicators and curate clinical interventions for culturally competent mental health care.

This paper presents the design and measurement of an IEEE 802.11ad standard compatible RF transceiver for 60GHz wireless communication system. In addition to the traditional half-duplex (HD) mode, this work supports full-duplex (FD) operation to deliver better channel utilization and faster response time for the system. The isolation between the transmitter and receiver from the architecture design to system integration for FD operation has been fully considered. A digital self-interference cancellation (DSIC) is implemented in MATLAB to verify the FD performance. The super-heterodyne architecture with an intermediate frequency (IF) of 12GHz is designed to suppress the image frequencies without using extra filters. A flexible phase-locked loop (PLL) synthesizer provides a local oscillator (LO) frequency with a 2kHz resolution. Other than the time division duplex (TDD) mode used in the conventional 60GHz system, a wide bandwidth baseband digital variable gain amplifier (DVGA) with a 3dB bandwidth of more than 4GHz also supports frequency division duplex (FDD) operation. The transceiver chip is fabricated in Tower Jazz 0.18µm SiGe BiCMOS process. With on-board antenna, the transceiver covers all four channels in 802.11ad standard with MCS-12 (7.04Gbps under 1.76GSym/s and 16-QAM) under 1.5m. In the proposed system design, the RF frontend based self-interference (SI) suppression from the local transmitter to receiver LNA is around 54dB. To achieve a practical FD application, the SI is further suppressed with the help of digital SI compensation. The measured power consumption for transmitter and receiver configuration is 194mW and 231mW, respectively, in HD mode and 398mW for FDD or FD operation mode.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

The regions with the best economy have a greater capacity to develop low-income or social impact housing, thus contributing to the reduction of poverty, and therefore, to the fulfillment of the Sustainable Development Goals. This is observed in fewer people living in extreme poverty and with fewer unmet basic needs. The present article analyzes the correlation between development by the main economic sectors in the different regions (departments) of Colombia, and the offer of low-income housing. The valid relationship found is between the economic condition of the regions (GDP) and non-social housing (more expensive commercial value) (Spearman´s Rho: 0.9). That means that there is an imbalance between regional economic capacity and the low-income housing offer because their economic potential allows them to have less of a demanding population, that is, living in poverty. This correlation is higher with activities that are mostly developed in an urban environment, such as manufacturing, construction, real estate, and finance and insurance. On the contrary, the correlation is lower with industries such as mining and agriculture, which mostly operate in rural areas. The analysis for low-income housing and economic sectors GDP yields low correlations, but are especially dismissible for more rural industries, such as mining and agriculture. The analysis shows the change of trend in the correlations for the year 2021, the beginning of the post-pandemic economic recovery.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

This study leverages the relationships between the Great Plains low-level jet (GP-LLJ) and the circumglobal teleconnection (CGT) to enhance the 30-day rainfall forecast skill in the Northern Great Plains (NGP). The assessment of 30-day simulated precipitation using the Climate Forecast System (CFS) is contrasted with the North American Regional Reanalysis, searching for sources of precipitation predictability associated with extended wet and drought events. We analyze the 30-day sources of precipitation predictability using (1) the characterization of dominant statistical modes of variability of 900-mb winds associated with the GP-LLJ, (2) the large-scale atmospheric patterns based on 200-mb geopotential height (HGT), and (3) the use of GP-LLJ and CGT conditional probability distributions using a continuous correlation threshold approach to identify when and where the forecast of NGP precipitation occurs. Two factors contributing to the predictability of precipitation in the NGP are documented. We found that multi-scale geospatial interactions occur at the daily and sub-seasonal time windows. The CFS reforecast suggests that the ability to forecast sub-seasonal precipitation increases in response to the enhanced simulation of the GP-LLJ and CGT. Finally, the multi-dimensional analysis of covariance reveals that high-precipitation forecasting skill is associated with a better prognostic of GP-LLJ and CGT.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

For two-dimensional forward-looking sonar imaging, high sidelobes significantly degrade the quality of sonar images. The cosine window function weighting method is often applied to suppress the sidelobe levels in the angular and range dimensions at the expense of the main lobe resolutions. Therefore, the improved spatially variant apodization imaging method for forward-looking sonar is proposed to reduce the sidelobes without degrading the main lobe resolution in angular-range dimensions. The proposed method is a nonlinear post-processing operation in which the raw complex-valued sonar image produced by a conventional beamformer and matched filter is weighted by a spatially variant coefficient. To enhance the robustness of the spatially variant apodization approach, the array magnitude and phase errors are calibrated to prevent beam sidelobe heightening from occurring prior to beamforming operations. The analyzed results of numerical simulations and a lake experiment demonstrate that the proposed method can greatly reduce the sidelobes to approximately -40 dB, while the main lobe width remains unchanged. Moreover, this method has an extremely simple computational process.

Use of fingerprints found at a crime scene is a common practice for identifying suspects in criminal investigations. Over the past two decades, attempts have been made to obtain additional information from fingerprints, beyond locating suspects as part of an investigation. This includes gender, age and nationality. Researchers demonstrated 75%-90% accuracy in gender classification based on fingerprint images. Nonetheless, despite promising results, these studies have several significant shortcomings with respect to their practical feasibility. First, they ignore the low quality and quantity of fingerprints collected from the crime scene since typically the scene of a crime has only one fingerprint collected, and the fingerprint might be partially or of poor quality as well. Second, as most results are based on a single database, public or private, it is difficult to generalize the most suitable method. Third, studies miss the untapped potential of Data-Centric AI (DCAI) approaches for improving results. The aim of this study was to compare, for the first time, the gender classification from a fingerprint using several datasets and with varying fingerprint image quality. The results from four databases are compared, three public and one internal private database. In addition, we utilize the latest Data-Centric AI (DCAI) approaches for improving classification results. The results demonstrate that a conservative Convolutional Neural Networks (CNN) such as VGG is sufficient for this task. Classification accuracy ranges from 80% to 95% depending on the quality of the fingerprint, with DCAI approaches adding 1%-4% improvement. For partially or low-quality fingerprint images, the periphery of a fingerprint is the most significant area for determining gender. The source code is also provided here for practical application.

Appeals to governments for implementing basic income are contemporary. The theoretical backgrounds of the basic income notion, only prescribe transferring equal amounts to individuals irrespective of their specific attributes. However, the most recent basic income initiatives all around the world are attached to certain rules with regard to the attributes of the households. This approach is facing significant challenges to appropriately recognize the vulnerable groups. A possible alternative for setting rules with regard to the welfare attributes of the households is to employ artificial intelligent algorithms that can process unprecedented amounts of data. Can integrating machine learning change the future of basic income by perdition of vulnerable to future poverty households? In this paper, we utilize a multidimensional and longitudinal welfare data comprising one and a half million individual data and a Bayesian beliefs network approach to examine the feasibility of predicting households’ vulnerability to future poverty based on the existing households’ welfare attributes.

This paper presents a Modified Gate Diffusion Input (MGDI) design with four inputs for Quantum-dot Cellular Automata (QCA) technology. QCA is a promising nanotechnology that offers benefits such as low power consumption, and high density, making it a potential alternative to CMOS technology. The proposed planar cell design has advantages over previous designs, including a 19% reduction in the number of cells, a 29% reduction in total energy consumption, and a 44% reduction in average energy loss at the same occupancy level. The proposed block is capable of implementing 21 basic combinational functions and various sequential functions. The simulation of functions in 18nm technology and energy consumption calculation indicates that the resulting circuits have improvements of 41%, 27%, 27%, and 20% compared to multiplexers, comparators, four-bit parity circuits, and single-bit memory, respectively. Additionally, the number of cells in the proposed circuits has improved by 10%, 7%, 22%, and 19%, respectively.

This study presents the design and implementation of a PLC microprocessor adhering to the IEC-61131-3 standard, executed on a Cyclone-V FPGA using a DE10-NANO development board. Our microprocessor optimizes the central processing unit by streamlining the data path, achieving a remarkable simulated response time of approximately 60 ns, equivalent to three clock cycles at a 50MHz frequency for Boolean operations. To substantiate our approach, we conducted practical experiments utilizing a FESTO conveyor station, employing relays as actuators, and incorporating optical and inductive sensors. The results underscore the feasibility of our proposed approach and serve as practical validation of its efficacy. This work introduces a promising avenue for the development of cost-effective PLCs employing SoC FPGA variants. Additionally, a thorough comparison of execution times with other early reported architectures. Our microprocessor outperforms even well-established PLCs like the S7-312, with substantial reductions in execution times of 94.54% for floating-point operations, 71.42% to 93.33% for word operations, and up to 78.57% for bit operations.

Obesity and overweight are associated with many metabolic diseases, such as hypertension, diabetes, and dyslipidemia, which are closely related to a sedentary lifestyle and lack of exercise. Aerobic exercise effectively increases the high-density lipoproteins-cholesterol (HDL-C) levels and decreases the triglyceride (TG) levels. The consumption of Cuban policosanol (Raydel®) is also effective in enhancing the HDL-C quantity and HDL functionality to treat dyslipidemia and hypertension. On the other hand, no study has examined the effects of a combination of high-intensity exercise and policosanol consumption in obese subjects to improve metabolic disorders. In the current study, 17 obese subjects (average BMI 30.0±1.1 kg/m2, eight male and nine female) were recruited to participate in a program combining exercise and policosanol (20 mg) consumption for 12 weeks. After completion, their BMI, waist circumference, total fat mass, systolic blood pressure (SBP), and diastolic blood pressure (DBP) decreased by approximately 15% (p=0.022), 12.7% (p=0.008), 33% (p=0.006), 11% (p<0.046), and 13% (p=0.007), respectively. In the serum lipid profile, at week 12, they showed a remarkable decrease in the total cholesterol (TC) and triglyceride (TG) levels, up to 17% (p<0.019) and 54% (p<0.002) from the baseline, respectively. Although the serum HDL-C was increased by approximately +12% from the baseline, the percentage of HDL-C in TC, HDL-C/TC (%), was increased by up to +32% (p=0.007) at week 12. The serum coenzyme Q10 (CoQ10) level was increased 1.2-fold in all participants at week 12 from the baseline. In particular, the male participants showed a 1.4-fold increase (p=0.027) from the baseline. The larger increase in serum CoQ10 was correlated with the larger increase in the serum HDL-C during 12 weeks. The hepatic function parameters were improved; the serum -glutamyl transferase decreased at week 12 by up to 55% (p<0.007), while the aspartate aminotransferase and alanine transaminase levels decreased within the normal range. In the lipoprotein level, the extent of oxidation and glycation were reduced significantly in VLDL and LDL, with a remarkable decrease in the TG content in particles. The antioxidant abilities of HDL2 and HDL3, such as paraoxonase (PON) and ferric ion reduction ability (FRA), were enhanced significantly by up to 1.8-fold (p<0.001) and 1.6-fold (p<0.001) at week 12. The particle size and number of HDL2 were increased up to +10% during the 12 weeks with a remarkable decrease in the TG content, glycation extent, oxidation up to 32% (p=0.032), 18% (p=0.043), and 11% (p=0.023), respectively. The particle number and diameter of HDL3 were increased by up to +9% with a remarkable increase in the PON activity, FRA activity, and TC content of +82% (p<0.001), +56% (p<0.001), and +32% (p=0.009), respectively. Expression of apolipoproteinA-I in HDL2 and HDL3 were significantly elevated more in both gender around 30~48% with more distinct band intensity and less glycation at week 12. These improvements in HDL quality and functionality were linked to the higher survivability of adult zebrafish and their embryos. Under the co-presence of carboxymethyllysine (CML), a microinjection of HDL2 to zebrafish embryo from week 0 resulted in approximately 47% survivability with developmental defects and attenuated speed. On the other hand, the HDL2 microinjection from week 12 resulted in remarkably higher survivability (~ 70%). In conclusion, 12 weeks of Cuban policosanol (Raydel®, 20 mg) consumption with high-intensity exercise showed significant improvement in blood pressure, body fat mass, blood lipid profile without liver damage, CoQ10 metabolism, and renal impairment. At week 12, all participants showed a remarkable decrease in oxidation and glycation extent in the VLDL and LDL with a decrease in the TC and TG content. Significant enhancement of the qualities and functionalities in HDL2 and HDL3 by the policosanol consumption were also detected: increase in apoA-I content, TC content, particle size, and particle numbers along with antioxidant abilities, such as PON and FRA.

The rapid advancement of technology has led to increased electronic consumption and a corresponding rise in e-waste generation. To address this issue, this study develops a low-carbon e-commerce closed-loop supply chain (LCE-CLSC) system with remanufacturer, platform, and the government as key stakeholders. An evolutionary game approach is employed to investigate the system's dynamics, analyzing the impact of stakeholder strategies on system equilibrium. Numerical simulations reveal important findings: Firstly, government initiatives promoting recycling, carbon taxes on traditional products, can incentivize remanufacturers to produce low-carbon items and encourage platform investment in recycling services. Secondly, higher sales revenues motivate remanufacturers to produce low-carbon products. Thirdly, consumer sensitivity to recycling services strengthens waste recovery when platforms increase investments in these services, leading to remanufacturers choosing low-carbon production. Lastly, government subsidies may become ineffective if the cost of remanufacturers' carbon reduction and platforms' recycling services exceeds their affordability. These findings offer insights for the sustainable development of obsolete electronic product recycling systems.

The purpose of this study was to determine the income, costs and revenue of the Gontor Putri 3 bakery. Want to know the efficiency of the bakery business in Karangbanyu Regency. The method used in this research is analytical descriptive by conducting a survey. The data used in this research is primary data. Data collection techniques use observation, interviews and documentation, while the process of analysis is quantitative descriptive. Using the R/C ratio, a value of 1.72 per month is obtained. This value indicates that the bakery factory in Karangbanyu is efficient because the value is more than one.

In space application, hybrid pixel detectors of the Timepix family have been considered mainly for measurement of radiation levels and radiation dosimetry in low earth orbits. By the example of the Space Application of Timepix Radiation Monitor (SATRAM), we demonstrate the unique capabilities of Timepix-based miniaturized radiation detectors for particle separation. Using a novel method for proton spectrum reconstruction, we were able to measure the spectrum of protons trapped in the inner Van-Allen radiation belt, for the first time with a single-layer detector. We assess the measurement stability and the resiliency of the detector to the space environment demonstrating that, even though degradation is observed, data quality has not been affected significantly over more than 10 years. Based on the SATRAM heritage and the capabilities of the latest-generation Timepix-series chips, we discuss their applicability for use in a compact magnetic spectrometer for deep-space mission or in the high radiation environment of the Jupiter radiation belts, and their capability for use as single-layer X- and γ-ray polarimeter. The latter was supported by measurement of the polarization of scattered radiation in a laboratory experiment, where a modulation of 80% was found.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

A millimeter-wave microstrip leaky-wave antenna array based on the substrate-integrated waveguide (SIW) and the complementary split-ring resonator (CSRR) is proposed in this paper. The slow wave characteristics of the SIW are enhanced by etching two rows of symmetrical CSRR-type slots on the surface of the SIW layer. The magnetic coupling between the CSRR-SIW layer and equally spaced circular patches array on the upper layer realizes the radiation of electromagnetic energy. In the 23~30 GHz (relative bandwidth 26.4%) operating frequency band, the horizontal polarization radiation beam scanning from -62° to -2° is realized, with a peak gain of 9.6~11.7 dBi, and the cross-polarization ratio is more than 43.8 dB.

Background: Hemangiomas are an aberrant proliferation of blood vessels and are the most frequent benign pediatric soft tissue tumors. Despite their being common, genital localisation is rare. This study aimed to assist doctors in the diagnosis, management, and treatment of paediatric vulvovaginal hemangiomas by conducting a review of the literature and also gathering some cases of patients from our clinic.Methods: We conducted a literature review including papers published between October 2021 and April 2023, and we described the cases of 3 patients who referred to our clinic with vulvovaginal hemangioma.Results: While most of hemangiomas are usually indolent and resolve with time, in some cases, especially vaginal and cervical ones, they might present with severe symptoms like heavy bleeding and need further instrumental investigation for diagnosis, like CT or MRI. As for the treatment many options are available with medical therapy or expectant management being the first choice.Conclusions: Vulvovaginal pediatric hemangiomas are rare and, so, more research should be done to how to detect and manage this lesions, especially the symptomatic and the psychologically impacting ones. For the time being treatment should personalized based also on the patient situation and clinician’s expertise.

The improvement of agricultural low-carbon efficiency is an important path to promote the realization of the "double carbon" goal in the Yellow River Basin. In the context of rapid urbanization development, it is of great significance to explore whether the promotion of urbanization will affect the agricultural low-carbon efficiency. Based on the panel data of 75 cities in the Yellow River Basin from 2000 to 2020, this paper uses super-DEA model, three-dimensional kernel density model and Markov chain model to measure and analyze the spatio-temporal evolution of agricultural low-carbon efficiency in the Yellow River Basin, on this basis, the panel Tobit model is used to analyze the relationship between urbanization and low-carbon efficiency in agriculture. The results show that: (1) The level of agricultural low-carbon efficiency in the Yellow River Basin is low and has not reached the effective state, showing a slow downward trend in general, among which, the agricultural low-carbon efficiency in the lower reaches is higher than that in the middle reaches, and the upper reaches is the lowest. (2) The agricultural low-carbon efficiency in the Yellow River Basin has a negative trend of transferring to the low level on the whole, and tends to maintain the original state level, and it is difficult to realize the leapfrog transfer between states. Agricultural low-carbon efficiency has obvious spatial spillover effect and "club convergence" phenomenon, high efficiency area has a positive driving effect on the neighborhood area, while low efficiency area has a negative impact on the neighborhood area. (3) The level of urbanization has a significant positive impact on the low-carbon efficiency of agriculture in the upper, middle and lower reaches of the Yellow River Basin, which plays an important role in promoting the green development of agriculture. Finally, based on the above research conclusions, relevant policy recommendations were put forward, in order to provide references for promoting the improvement of low-carbon agricultural efficiency and promoting high-quality agricultural development in the Yellow River Basin.

Drowning remains a prominent global pediatric health concern, necessitating preventive measures such as educational initiatives for children and caregivers. This study aimed to assess the feasibility and educational effectiveness of an interactive puppet show centered on water safety for children and parents. A 30-minute original theater performance, featuring two actors and three puppets (a girl, a crab, and a lifeguard), was conducted. Subsequently, 185 children (aged 4 to 8) and their 160 parents (134 mothers and 26 fathers) participated in this quasi-experimental study. Pre- and post-show tests were administered to evaluate knowledge and behaviors in aquatic environments. Prior to the puppet show, 78% of children exhibited basic aquatic competency. Only 33% considered swimming alone risky. Following the intervention, 81.6% of children changed their perception of the risks of solo beach activities, showing improved knowledge of emergency number activation (from 63.2% to 98.9%, p&lt;0.001). The intervention increased parents' intention to visit lifeguard-patrolled beaches and improved their CPR knowledge for drowning victims by 58.8%. In conclusion, a drowning prevention puppet show positively impacts children and parents, potentially enhancing safety behaviors during water-related leisure activities, warranting consideration as part of comprehensive drowning prevention strategies.

Objective: To analyze the relation between alterations in the growth hormone (GH)/insulin-like growth factor 1 (IGF-1) axis during the first 6 months of life and weight in children born in the Lower Middle São Francisco region. Methods: This is an analytical cohort, with a quantitative approach and a translational perspective. Thirty children with low and normal birth weight were initially identified in a hospital and reapproached at 3 and 6 months of age. Birth weight and alterations in GH/IGF-1 curves at birth, third month, and sixth month of life. Results: Weight gain during the 6 months of follow-up in newborns with low birth weight was greater compared to newborns with normal birth weight. All children who were born with low birth weight had an altered GH/IGF-1 curve at birth (p = 0.002). Most newborns with low birth weight maintained the alteration in the GH/IGF-1 curve at the third month of life (p = 0.027). Regarding the GH/IGF-1 curve at the sixth month, alteration persisted in greater proportion among children with low birth weight. Conclusion: Alterations in insulin resistance markers, demonstrated by increased GH without a proportional increase in IGF-1, were observed to be significant in children with low birth weight, with greater adiposity in this group, which may increase the risk of metabolic diseases in later life.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

Background. The purpose of the study was to evaluate the intensity and frequency of low back pain (LBP) in people with multiple sclerosis (PwMS) and the patient's knowledge of physiotherapeutic methods of combating. Methods. In this study, patients with confirmed multiple sclerosis were selected. The study was carried out using an original survey questionnaire and a numerical pain intensity scale (Visual Analogue Scale). PwMS were divided into 3 age groups: 18-30 years, 31-50 years, and over 50 years. Results. Ninety PwMS (68 women and 22 men) aged 18 to 60 years were included in the study. The mean duration of the disease was 9.5±4.9 years, and the mean EDSS was 3.5±1.6. Most of the patients had a relapse-remitting form. 68.9% of PwMS felt lower back pain (n = 62). The relationship tested was statistically significant (p=0.0000012), and the strength of the relationship was high (rc=0.695). The average level of low back pain among PwMS was 4.7 out of 10 on the VAS scale. The prevalence of LBP was higher in female patients (p<0.001), with a secondary progressive form (p<0.001) and with a longer duration of the disease (p=0.023). The most widely used methods of LBP therapy were kinesitherapy and manual therapy. Conclusions. LBP is common in multiple sclerosis. A female sex, a secondary progressive form of MS, and a longer duration of the disease increased the risk of LBP. It is important to implement properly planned physiotherapy activities and educate patients on how to combat LBP.

This study aimed to assess the prevalence and identify risk factors for schistosomiasis among school-aged children in low- and middle-income communities. A retrospective cross-sectional study was conducted, involving the examination of 24 034 children for Schistosoma haematobium ova. Data were analyzed using IBM Statistical Package for the Social Sciences (SPSS) version 27. Logistic regression was employed to determine the factors associated with schistosomiasis. The overall prevalence of schistosomiasis in the study population was 75%, with higher rates observed in rural-dominated areas, particularly Bushbuckridge (73%) and Nkomazi (51%). Age, a history of bilharzia, and the presence of blood in urine were significantly associated with schistosomiasis, while being a female child was found to be a protective factor. This study underscores the importance of implementing robust screening procedures and the necessity for health education to mitigate the high prevalence of schistosomiasis and prevent its further spread.

Chronic Low Back Pain (CLBP), defined as pain persisting for at least 12 weeks, is a significant public health issue, with prevalence intensifying due to an ageing global population, amassing approximately 619 million cases in 2020 and projected to escalate to 843 million by 2050. Given the multitude of therapeutic modalities available for CLBP, this research sought to ascertain their respective efficacies in ameliorating pain and disability. We specifically scrutinized Multidisciplinary Biopsychosocial Rehabilitation (MBR) among adults enduring non-specific low back pain for over 12 weeks, excluding acute pain conditions and pre-study surgical interventions. MBR is an approach encompassing various modalities, including exercise, behavioral therapies, educational programs, and work conditioning aspects, necessitating a comprehensive Network Meta-Analysis (NMA) to fully grasp the extensive scope of its impact. The constructed network comprised diverse MBR modalities (behavioral, educational, and work conditioning) alongside exercise therapy (ET), minimal intervention, and usual care, serving as controls with pain and disability as outcomes. Through the analysis of 4,619 initially identified studies, 93 were included, encompassing a total of 8,059 participants. The NMA conducted substantiated that both ET and MBR modalities were notably effective in alleviating CLBP, with education-oriented MBR emerging as the most efficacious for pain mitigation and behavior-focused MBR for disability reduction. Nevertheless, the discerned differences amongst the treatments were minimal and uncertain, highlighting that no modality was definitively superior to the others. The analysis revealed low global and local inconsistency within the network, underscoring the reliability of the observed outcomes. Given the intricate nature of CLBP, embodying various facets, our findings advocate for a combined therapeutic approach to optimize treatment efficacy. Nonetheless, the presence of high study heterogeneity and potential biases necessitates cautious interpretation of the results, prompting future research.

Rural areas, as a system, face multiple challenges. Among these are population decline and attendant economic and social maladies namely demographic issues considering a scarce population. Pull factors for immigrants to go to other countries are known, nevertheless, to comprehend factors for remaining in rural areas after arriving could support a strategic local policy, and for an informed practice. The purpose of the study is to explore motivations shaping immigrants’ intentions to stay in the Alentejo, a depopulated region in Portugal, using a qualitative approach. Research questions are: What motivates immigrants to remain living in depopulated regions in Portugal? Furthermore, what contributions can practitioners and immigrants give for local policy and practice? Eight practitioners and fifteen non-European Union immigrants living in this region were interviewed between 2020 and 2021. Empirical data were analysed, supported by MaxQDA software. Results point out that the intention to remain in rural areas arise from a progressive construction, it is a process that immigrants experience to become motivated to stay long-term. Factors influencing the process include four components: 1. instrumental and material motivations; 2. emotional and social motivations; 3. motivations based on quality of life; and 4. motivations based on political dimensions. Components are conditioned by the availability of : stable and suitable jobs, access to decent and affordable housing, as well as quality of education and health services for their children; additionally to socio-emotional satisfaction, as family reunification, migrants network, integration and real intercultural living in the host community, close relationships to practitioners from social services; and quality of life, such as lower rents, peaceful and secure living conditions, granted a better future for their children as in any another place in Europe, associated finally to the simplified policy enabling one to become a legal citizen. Conclusions highlight implications for policy and practice, suggesting more investment for rural regions to reverse depopulation reality.

The rising prevalence of autism internationally has been accompanied with an increased appreciation of the poorer mental health experienced by people with this condition and also of their family care-givers. In particular higher incidences of anxiety and depression are reported in high income nations and these conditions are likely to be under-recognised and under-reported in lower resourced regions or countries. Mainstream mental health services seem to be ill-equipped to respond adequately to the needs of autistic persons and their care-givers. This scoping review of 30 recently published literature reviews covering over 1,000 journal articles, summarises the insights and strategies that have been shown to promote the mental health and emotional wellbeing of autistic persons. In particular, a focus on family-centred, community-based supports is needed that aim to enhance social communication, extend social connections and promote an individual’s self-esteem, self-determination and social motivation. These low-cost interventions are especially pertinent in low resourced settings but they can be used internationally to prevent mental illness and assist in the treatment of anxiety and depression in autistic persons and their family carers. The priority is to focus on primary care responses with cross-sectoral working rather than investing in high-cost psychiatric provision.

Natural deep eutectic solvents (NADES) have been shown as selective and environmentally friendly solvents for the extraction of bioactive compounds. However, studies on the solubility of low molecular weight carbohydrates (LMWC) in NADES are scarce. In this work, new solubility data of LMWC in NADES are provided and a new approach based on the use of these solvents for the efficient fractionation of bioactive carbohydrates was explored for the first time. Several mono- and disaccharides and three NADES based on choline chloride (ChCl) and different donors [2-ethylene glycol (EtG), glycerol (Gly) and ethanedioic acid dihydrate (Eth)] were considered. While degradation of carbohydrates, mainly ketoses, was detected with ChCl:Eth due to its acidic nature, ChCl:EtG and ChCl:Gly were found to be useful alternatives for selectively separating bioactive ketoses and their corresponding aldoses (e.g. lactulose/lactose and tagatose/galactose) present in equimolar binary mixtures. In addition, the usefulness of ChCl:EtG for the selective enrichment of lactulose to be used as food ingredient or nutraceutical was proven (from a 25% in the reaction mixture to a 56% in the purified sample). NADES could be used for the selective fractionation of value-added carbohydrates from interfering sugars for several applications including food science, engineering or pharmaceuticals.

Product introductions play a pivotal role in the success and competitiveness of manufacturing, particularly in the context of new product development. Low-volume manufacturing companies exhibit distinct characteristics that significantly influence the product introduction process. Notably, the quality of information exchange between product design and production interfaces becomes paramount in this high-mix and low-volume industry. Consequently, there exists a pressing need to explore various methods for adapting and customizing management mechanisms and strategies to align with the unique requirements and characteristics of low-volume manufacturing and its associated product introduction processes. While the need for this knowledge is critical in the context of low-volume manufacturing, a majority of existing studies predominantly focus on the management aspects within high-volume manufacturing. Therefore, the primary aim of this study is to investigate the customization of product introduction management strategies to enhance the quality of information content within the realm of low-volume manufacturing. Drawing upon a longitudinal analysis of new product introductions within a low-volume manufacturing company, this study narratively elucidates how the examined company implemented product introduction management strategies to facilitate the enhancement of information content quality during the product introduction phase. The study presents its findings on management strategies across three key stages: pre-implementation, post-implementation, and subsequent modification and refinement of strategies following the initial round of implementation. By shedding light on these strategies, this study offers a comprehensive understanding of management approaches in the context of low-volume product introduction. As a result, it makes a valuable contribution to the discourse on information management and interface management in the high-mix, low-volume manufacturing literature.

The manufacturing geometrical variability in axial compressors is a stochastic source of uncertainty, implying that the real geometry differs from the nominal design. This causes the real geometry to lose the ideal axial symmetry. Considering the aerofoils of a stator vane, the geometrical variability affects the flow traversing it. This impacts the downstream rotor, especially when considering the aeroelastic excitation forces. Optical surface scans coupled with a parametrization method allow for acquiring the information relative to the real aerofoils geometries. The measured data are included in a multi-passage and multi-stage CFD setup to represent the mistuned flow. In particular, low excitation harmonics on the rotor vane are introduced due to the geometrical deviations of the upstream stator. The introduced low engine orders as well as their amplitude depend on the stator geometries and their order. A method is proposed to represent the phenomena in a reduced CFD domain, limiting the size and number of solutions required to probabilistically describe the rotor excitation forces. The resulting rotor excitation forces are reconstructed as a superposition of disturbances due to individual stator aerofoils geometries. This indicates that the problem is linear in in the combination of disturbances from single passages.

Oxidative stress is one of the primary instigators of the onset of various human ailments, including cancers, cardiovascular diseases, and dementia. Particularly, oxidative stress has a severe effect on low-density lipoprotein (LDL) oxidation, leading to several detrimental health effects. Thereof, in this study, the effect of beeswax alcohol (BWA) was evaluated to prevent LDL oxidation, enhancement of paraoxonase 1 (PON-1) activity of high-density lipoprotein (HDL), and zebrafish embryo survivability. Furthermore, the implication of BWA consumption on the oxidative plasma variables was assessed by a preliminary clinical study on middle and older human subjects (n=50). Results support BWA augmentation of PON-1 activity in a dose-dependent manner (10-30 μM), which was significantly better them the effect exerted by coenzyme Q10 (CoQ10). Moreover, BWA significantly curtails CuSO4 (final 0.5 μM) evoked LDL/apo-B oxidation and a marked reduction of lipid peroxidation in LDL. The transmission electron microscopy (TEM) analysis revealed a healing effect of BWA towards the restoration of LDL morphology and size impaired by the exposure of Cu2+ ions (final 0.5 μM). Additionally, BWA counter carboxymethyllysine (CML, 500 ng) induced toxicity and rescued zebrafish embryos from development deformities and apoptotic cell death. A completely randomized, double-blind, placebo-controlled preliminary clinical study on middle and older-aged human subjects (n=50) exhibited that 12 weeks of BWA (100 mg/day) supplementation efficiently diminished serum malondialdehyde (MDA), total hydroperoxides, and enhanced total antioxidant status by 25%, 27%, and 22%, respectively, compared to the placebo control and baseline values. Furthermore, the consumption of BWA did not exhibit any noteworthy changes in anthropometric profile, lipid profile, glucose levels, and biomarkers pertinent to kidney and liver function, thus confirming the safety of BWA for consumption. Conclusively, BWA prevents LDL oxidation, enhances PON-1 activity in HDL, and has a positive impact on the oxidative variables of human subjects.

Water scarcity challenges have necessitated the adoption of water-saving techniques in protected and nom-protected farming. This study aimed to assess the performance of a water-saving soil-less cultivation technique and to compare it with conventional soil-based cultivation in protected farming. The soilless technique used local gravel and a mixture of peat-moss, humin-substrate, and perlite in ratios of 4:3:1.5. Three irrigation regimes were imposed using emitters 8Lh-1 design discharge (D1) emitters with 6Lh-1 design discharge (D0.75) and 4Lh-1 de-sign discharge (D0.5) for the two cultivation methods during the growth cycle of tomato by drip irrigation. The vegetative growth, fruit yield and water consumption were measured and water productivity was determined. Moreover, an economic assessment was carried out by estimating and comparing economic coefficients for the two cultivation methods. Estimated coefficients include revenues, net profit, benefit-cost ratio, break-even levels of production and prices, revenues over variable cost, and revenues on investment. The tomato fruit yield under soil-based cultivation overtopped the yield under soilless cultivation. The water productivity under the soilless cultivation was almost twice that (24.3 kg m-3) of the soil-based cultivation (15.5 kg m-3). The soilless cultivation saved 50% of irrigation water applied by the conventional soil-based method, saving energy and soil from deterioration. Revenues and net profits stimulated by higher yield coupled with lower variable cos supported the soil-based cultivation. The economic assessment showed that both cultivation methods were economically viable. However, the soil-based cultivation method was more profitable due to its higher fruit yield. Overall, the results of this study suggest that the soilless cultivation technique is a viable option for wa-ter-saving cultivation. However, the soil-based cultivation method is still more profitable due to its higher fruit yield

To systematically assess the effect size of different methods for patients with low back pain. PubMed, Cochrane Library, Web of Science, and Google Scholar. databases were searched in January 2023. This study has been developed in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) Statement. The key search terms were: “Low back pain”, “Back pain”, “SF-36”, “VAS”, “VASP”, “Roland-Morris”, “Oswestry Disability Index”, and “conservative treatment”. The risk of bias was determined for each randomized trial using the Cochrane Risk of Bias Tool, and the methodological index for non-randomized studies (MINORS). The outcomes included SF-36 Mental, SF-36 Physical, VAS, Roland-Morris, and Oswestry Disability Index. R 4.0.5 software was used, and standardized mean difference (SMD) and 95% confidence intervals (CI) were calculated for continuous outcomes, random model. Twenty-five studies were included. Depending on the outcome being measured, the effect size of different methods in treating low back pain varies from small to large as follows: SF-36 Mental (SMD = 0.39, p &lt; 0.0001), SF-36 Physical (SMD = 0.55, p &lt; 0.0001), VAS (SMD = -0.84, p &lt; 0.0001), Roland-Morris (SMD = -0.45, p &lt; 0.0001), and Oswestry Disability Index (SMD = -0.61, p &lt; 0.0001). Our meta-analysis indicates the positive effects of applying different methods in the treatment of low back pain. PROSPERO registration number: CRD42022371282

Under the "dual carbon" target in China, virtual power plants (VPPs) play an important role in improving grid security and promoting clean and low-carbon energy transformation. VPPs can integrate and control distributed resources to participate in the energy market and make full use of distributed resources. However, the intermittency and volatility of renewable energy and the "heat-driven" working mode of CHP units create contradictions that seriously affect the peak-shaving ability of VPPs and lead to high carbon emissions. To solve these problems, this paper aggregates CHP units, wind power, photovoltaics, carbon capture, hydrogen energy storage, and electric boilers into a new type of virtual power plant. The "hydrogen energy storage-electric boiler" joint decoupling CHP working mode is used to strengthen the coupling relationship between electric-thermal-hydrogen load. At the same time, a tiered carbon trading mechanism is considered, with the net profit of the VPP as the optimization objective, balancing economic and environmental considerations. A low-carbon economic dispatch model for VPPs is established, and a genetic algorithm is used for optimization. Three different scheduling strategies are set, and simulations are conducted in three different seasonal scenarios. The results show that the net profit in the cooling season increased by 50.4%, and carbon emissions decreased by 42.3%. In the transitional season, the net profit increased by 39.2%, and carbon emissions decreased by 44.9%. In the heating season, the net profit increased by 19.4%, and carbon emissions decreased by 43.4%. Overall, the proposed dispatch strategy can improve the new energy consumption capacity and total revenue of VPPs while achieving the goal of reducing carbon emissions.

Several studies have shown that physical activity (PA) is related to physical and mental health. Yet, there are few studies on the frequency of PA as it relates to health and a healthy lifestyle. The purpose of this study was to investigate the relationship between the frequency of practicing different types of physical activities (dependent variables), living a healthy lifestyle (BMI, smoking and alcohol consumption), physical health (sum of all doctor visits except psychiatrists) and mental health (a sum of visits to psychiatrists) at different ages (independent variables). We fo-cused on three types of PA: (1) medium to high-intensity aerobic exercises; (2) low to medium intensity relaxing and stretching exercises, (3) outdoor leisure PA. 9,617 participants (ages: 19 -81) were included in the study (with health registries over a period of 10 years prior to a cross-sectional survey). Descriptive statistics and multinomial logistic regression on frequencies of three types of PA and factors related to health and healthy lifestyles, as well as age and sex, were performed in this study. The results indicate that a higher frequency of practicing PA had a higher probability of association with the following factors: lower BMI, less or non-smoking behavior (types 1 & 3); higher education (types 1 & 2); higher age (types 2 & 3) and better physical health (type 1). Occasional (practicing sometimes) PA, type 2, was positively associated with poorer mental health (higher number of psychiatrist visits). Women were more likely to practice PA type 2, and men – PA types 3 & 1. Conclusion: In general, a higher frequency of PA is related with better health and healthy life styles; with the exception of PA type 2 that is related to poorer mental health.

The airflow carried by artificial aeration provides oxidant O2 for microbial growth and mineral dissolution in heap bioleaching. To investigate the effect of forced aeration rate on bioleaching of low-grade copper sulfide ores, column bioleaching experiments with six columns were conducted in the aeration range of 0~150 L/h at 30~45 ℃. The results showed that when the aeration rate was higher than 95 L/h, the proportions of heap settlement and fine particles mass were much greater than that without aeration. The final total Fe concentration and bacterial cell numbers in pregnant leach solution increased with the increase of aeration rate.The final concentrations of Cu2 + in the mother liquor under aeration conditions of 60-150 L / h were 1.411, 1.432, 1.498, 1.491 and 1.583 g / L, respectively, which were higher than 1.345 g / L under non-aeration conditions. When the aeration rate was 150 L / h, the final Cu leaching rate was 80.1 %, which was 11.4 % higher than that without aeration ( 68.7 % ). Furthermore, in the early stage of leaching, copper leaching rate with 95 L/h aeration rate remained the highest. 结论Artificial aeration accelerates the bioleaching of low-grade copper sulfide ores by improving porosity structure, temperature range of bacterial activity and microbial catalyzed dissolution of targeted minerals.

Camera malfunctions or loss of storage elements in imaging devices may lead to loss of important image information or random impulse noise interference. Low rank is one of the important prior information in image optimization processing. This paper uses different low-rank constraint models of the image matrices to recover the impulse interference satellite images. Firstly, an overview of image inpainting models based on nuclear norm, truncated nuclear norm, weighted nuclear norm, and matrix-factorization-based F-norm is presented, and corresponding optimiza-tion iterative algorithms are provided. Then, we conducted experiments under three types of pulse interference and provided visual and numerical results. Finally, it is concluded that the WSVT_ADMM method based on the weighted nuclear norm can obtain the best image inpainting results; The UV_ADMM method based on F norm of matrix factorization has the least computa-tion time and can be used for large-scale low-rank matrix computation; The WSVT_ADMM method based on weighted nuclear norm and the TSVT_ ADMM method based on truncated nuclear norms can significantly improve the repair effect compared to the nuclear norm-based methods such as SVT, SVP, and n_ADMM.

Conclusion: When applied to the air-abraded Filtek™ Bulk Fill Flowable Restorative composite surface, 10-MDP-containing adhesives perform better than 10-MDP-free adhesives. The binding strength was unaffected by the 10-MDP-containing adhesives' chemical makeup. The bond strength endurance of adhesives containing 10-MDP decreases with age. Keywords: keyword 1; keyword 2; keywords: low-viscosity bulk fill composite, universal adhesives, self-etch adhesive, 10-MDP, aging, bond strength.

Iterative Stochastic decoding is an alternative to standard fixed-point decoding of Low-density parity check codes (LDPC) to reduce inter-node routing. In this paper, we propose a Flexible Field-Programmable Gate Array (FPGA)-Based Stochastic decoding (SD) hardware architecture for LDPC codes in the Fifth-Generation (5G) New Radio (NR) Standard that supports decoding of set of various code rates. This decoder’s runtime flexibility is desirable to switch a better performing code rate automatically based on the channel conditions without the extra time needed for reprogramming of FPGA. An offline design method is implemented to generate the hardware description language (HDL) code description of the decoder for the required code-rate set, which is further synthesized and integrated into the Xilinx Kintex-7 series FPGA board to determine the hardware resource utilisation and processing throughput. The Synopsys design tools were employed during both the simulation and synthesis stages, in combination with TSMC 65-nm CMOS standard cell technology, to facilitate comparative analysis. Compared with state-of-the-art designs, the proposed architecture reduces hardware utilization by up to 26% and achieved energy efficiency by 52%.

In response to new developments of work and employment in high-income countries (HICs), psychosocial aspects of work and health received increased attention. In contrast, middle-income countries (MICs) are mainly concerned with severe challenges of noxious and dangerous material work environments, poor employment conditions, and deficient social policies, leaving psychosocial aspects in a marginal role at best. More recently, differences between these two worlds were even aggravated by the COVID-19 pandemic. Yet, with economic globalisation and growing worldwide interconnectivity, the world of work in MICs is being rapidly transformed, sharing several concerns with modern Western societies. In this process, psychosocial occupational health will become an increasingly pressing issue. This contribution explores to what extent psychosocial aspects of work and health are already addressed in research originating from MICs. A selective focus on recent findings from two regions, Asia Pacific and Latin America, reveals a high degree of awareness of, and inquiry into, work-stress related problems within these countries. Importantly, in addition to incorporating research progress from HICs, these analyses identify new aspects within specific cultural and socio-economic environments, thus enriching the international state of art.

In this paper, the problem of autonomous optimal absolute orbit keeping for a satellite mission in Low Earth Orbit using electric propulsion is considered. The main peculiarity of the approach is to support small satellite missions in which the platform is equipped with a single thruster nozzle which provides acceleration on a single direction at a time. This constraint implies that an attitude maneuver is necessary before or during each thrusting arc to direct the nozzle into the desired direction. In this context, an attitude guidance algorithm specific for the orbit maneuver has been developed. A Model Predictive Control scheme is proposed, where the attitude kinematics are coupled with the orbital dynamics in order to obtain the optimal guidance profiles in terms of satellite state, reference attitude, and thrust magnitude. The proposed control scheme is developed exploiting Formation Flying techniques where the reference orbit is that of a virtual spacecraft that the main satellite is required to rendezvous with. In addition to the controller design, the closed loop configuration is presented supported by numerical simulations. The efficacy of the proposed autonomous orbit keeping approach is shown in several application scenarios.

This study examined the impact of Vibration-Assisted Drilling (VAD) on hole quality and residual stress in Ti-6Al-4V ELI material. Ti-6Al-4V ELI possesses excellent mechanical properties but presents challenges in machining, including chip evacuation, burr formation, and elevated cutting temperatures. VAD, particularly Low-Frequency Vibration-Assisted Drilling (LF-VAD), has been explored as a potential solution to address these issues. The research com-pares LF-VAD with conventional drilling (CD) under various cutting and cooling conditions. LF-VAD exhibits higher maximum cutting forces under specific conditions, which result in accel-erated tool wear. However, it also demonstrates lower RMS (Root Mean Square) forces com-pared to CD, offering better control over chip formation, reduced burr formation, and improved surface roughness within the hole. Furthermore, LF-VAD generates greater compressive residual stresses on the hole's inner surface compared to CD, suggesting enhanced fatigue performance. These findings indicate that LF-VAD holds promise for improving hole quality, fatigue life, and overall component durability in Ti-6Al-4V machining applications.

This randomized control trial aims to test the hypothesis that twice-daily nurse-administered saline enema(SE) is comparable to physician-administrated SE in very low birth weight infants (VLBW) with meconium obstruction of prematurity (MOP). MOP is defined as no bowel opening for 48 h, and treatment failure is defined as the need for additional intervention and safety. Twice-daily SE was administered by accredited nurses, surgeons/neonatologists using standardized protocols. The outcomes were comparability of nurse to physician-administered SE in terms of frequency of administration, catheter insertion length and volume of enema, daily maximum meconium output, and treatment failure, defined as the need for additional intervention. Safety outcomes were evaluated. Twenty-eight infants were managed with SE. 389 SE were administered, 96 and 293 in 750-999g and 1000-1500g birth weight groups, respectively. Nurses administered 72.9% and 81.5% of SE in 750-999g and 1000-1500g birth weight groups, respectively. Physicians performed the rest of the SE. Daily meconium output was comparable in nurse and physician-administered SE in both groups. There were no treatment failures or adverse events in both SE group. SE administered by nurses was found to be comparable in terms of safety, efficacy, and frequency of administration to that of physician-administered SE.

Low Emission Zone (LEZ) is an important mechanism to limit the negative environmental impact of traffic pollution in an urban area. Car traffic in the zone is strictly regulated to meet certain technical and environmental criteria. Such solutions of urban environment protection are gaining popularity, especially in European conurbations. Nowadays there are above 300 zones in Europe, mostly established in Italy and Germany. So far there are no LEZs in Eastern and Central European countries. However, the Warsaw authorities are just discussing launching of a LEZ in the city in 2024. According to the ongoing project, the zone is to be launched gradually, in five phases between 2024 and 2032, with the traffic criteria being tightened accordingly. The progressive emission reductions of the predominant pollutants in LEZ in consecutive phases were estimated on the basis of the Real Driving Emissions (RDE) test, carried out in 2020 by the ICCT. The gradually reduced emissions of NOx and PM were subsequently utilized as the input dataset for the regional CALPUFF model predictions, to calculate concentrations of these main traffic-induced pollutants within the LEZ area. The direct effect of the zone activation is reduction of air pollution in the urban center, which is mostly exposed to the pollution risk due to heavy traffic. Computer simulations reveal that implementation of the zone in the case of Warsaw will result in a quite significant reduction of NOx concentrations within the LEZ, such that its mean concentration in the zone becomes comparable to the rest of the conurbation. However, it will bring only a slight reduction of PM2.5 concentrations. This situation is due to the long-standing dominance of coal combustion in the Polish economy, which also applies to the urban municipal sector. As a consequence, particulate matter emissions of this sector are clearly predominant over the road traffic contribution. Balance can be achieved once the ongoing de-carbonization of the national economy has been completed.

NUSES is a planned space mission aiming to test innovative observational and technological approaches related to the study of low-energy cosmic rays, gamma rays and high-energy astrophysical neutrinos. Two scientific payloads will be hosted onboard the NUSES space mission: Terzina and Zirè. Terzina will be an optical telescope readout by SiPM arrays, for the detection and study of Cerenkov light emitted by Extensive Air Showers generated by high-energy cosmic rays and neutrinos in the atmosphere. Zirè will focus on the detection of protons and electrons up to a few hundred MeV and to 0.1-10 MeV photons and will include the Low Energy Module (LEM). The LEM will be a particle spectrometer devoted to the observation of fluxes of low-energy electrons in the 0.1-7 MeV range and protons in the 3-50 MeV range along the Low Earth Orbit (LEO) followed by the hosting platform. The detection of Particle Bursts (PBs) in this Physics channel of interest could give new insight into the understanding of complex phenomena such as eventual correlations between seismic events or volcanic activity with the collective motion of particles in the plasma populating van Allen belts. With its compact sizes and limited acceptance, the LEM will allow the exploration of hostile environments such as the South Atlantic Anomaly (SAA) and the inner van Allen belt, in which are expected electron fluxes of the order of 106−7 cm−2 sr−1 s−1. Concerning the vast literature of space-based particle spectrometers, the innovative aspect of the LEM resides in its compactness, within 10x10x10 cm3, and in its “active collimation” approach dealing with the problem of multiple scattering at these very low energies. In this work, the geometry of the detector, its detection concept, its operation modes and the hardware adopted will be presented. Some preliminary results from the Monte Carlo simulation (Geant4) will be shown.

A multicenter, prospective cohort study conducted in 5 physiotherapy clinics in the UAE from January 2021 to March 2023 to assess coronal lumbar spine radiographic parameters as a predictor of conservative therapy outcomes in patients suffering from low back and leg pain due to lumbar disc herniation (HNP). Ninety patients (mean age 44 yrs., 54% male) with lumbar HNP underwent conservative therapy. All participants received lumbar spine MRI and radiography to assess spine alignment. Interventions included specific exercises, diathermy, traction, education, a home-based exercise pro-gram, and medications. Detailed demographic data was collected. Follow-up was 6-months after discharge. A successful outcome was based on a minimum of the following four outcomes: (1) reduction of pain by 17.5 points (0–100 NRS); (2) fatigue reduction by 7.5 points; (3) distress reduction by 5 points; and (4) interference reduction by 9.5 points. At 6-month follow-up it was found that patient age, education, and radio-graphic determined lumbosacral angle measures significantly affected the odds of a successful outcome. Increasing age 1-year significantly decreased the odds of success of improving pain, fatigue (OR = 0.85, p = 0.016) and interference scores (OR = 0.89, p = 0.042) by 15%, 15%, and 11% respectively. Lower education significantly increased the odds of success for improving pain, fatigue, and interference by 26.18, 26.18, and 7.5 (p = 0.006, = 0.006, and = 0.029 respectively). Increasing (worsening) the radiographic lumbosacral angle by each 1° significantly reduced the odds of success for improving pain, fatigue, distress, and interference by 3.52, 3.52, 27.99, and 2.55, respectively (p < 0.001, < 0.001, = 0.003, = 0.001). Our findings indicate that younger age, less education, and better coronal radiological lumbar spine alignment all had a substantial impact on the likelihood of success of 6-month outcomes in patients suffering from chronic lower back pain and radiculopathy due to HNP.

Background Most of the Leber hereditary optic neuropathy (LHON) cases are bilateral and sequential, how-ever there are rare unilateral examples, or those in which the delay of onset of vision loss between one and the other eye is longer. In the case of presumed childhood amblyopia in one eye, the vision loss in the good eye may be the only symptom of bilateral disease, that was unnoticed in previ-ously amblyopic eye, or a preexisting episode of LHON on the “amblyopic” eye. Clinical decision in such cases may be difficult and suggestive for other forms of atypical optic neuropathy until confirmed by genetic testing. Case series We present three genetically confirmed (MT-ND1:m.3700G>A, MT-ND6:m14484 T>C, and MT-ND4:m.11778G>A) patients with subacute vision loss in previously good eye with the other eye believed to be amblyopic from the childhood, and their features different of what would be expected in true amblyopia. In all, electrophysiology testing showed bilaterally reduced ampli-tude of PERG with low VEP P100 wave amplitudes and prolonged peak time in both eyes, also unusual for amblyopia. During the follow-up, pallor of the optic discs progressed in all eyes. Significant thinning of the retinal nerve fiber layer around the optic disc (pRNFL) and ganglion cell complex (GCC) in the macular region was present. All three patients had peculiar history. First patient was treated for presumed hyperopic amblyopia that did not improve since child-hood and experienced visual loss on the good eye at the age of 17 and was negative for the three typical LHON mutations. Extended testing confirmed atypical pathogenic variant MT-ND1:m.3700G>A in homoplasmy. The second patient with presumed strabismic amblyopia had unusual presentation of vision loss only at the age of 61 and after exclusion of other causes, typical MT-ND4:m.11778G>A pathogenic variant was found in homoplasmy. The third case was peculiar as he had presumed strabismic amblyopia since childhood and had some degree of disc pallor in the amblyopic eye upon presenting with loss of vision on the good eye at the age of 21 and typical pathogenic variant m14484 T>C, p.Met64Val was subsequently confirmed. However, one year after the disease onset, he started to experience significant spontaneous functional im-provement in the non-amblyopic up to 1.0 Snellen, whilst improvement in the presumed amblyop-ic eye was modest, suggesting preexisting amblyopia. This interestingly extensive improvement was carefully followed by electrophysiology as well as visual acuity and fields. Conclusion This report shows three different scenarios of presentation of LHON in patients with presumed uniocular amblyopia from childhood. In such cases, the diagnosis may be difficult and detailed structural and functional evaluation of the optic nerve head is necessary to assess whether earlier LHON episode was misdiagnosed as amblyopia or whether LHON presented bilaterally on both eyes whilst only being noticed in the previously good eye.

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

In the context of post-harvest pest management in agricultural products, the adoption of modified atmospheres presents an eco-friendly alternative to conventional pesticides. This study focuses on nitrogen gas as a potential agent for insect control in stored commodities, utilizing computational simulations to investigate its penetration and distribution within two common storage configurations: chamber-contained pallets and silos. By employing the convection-diffusion equation, the simulations reveal insights into nitrogen distribution dynamics and duration required for oxygen reduction. The results highlight the influence of boundary conditions, commodity porosity, and convection effects on nitrogen dispersion. In chamber scenarios, boundary condition type significantly affects oxygen reduction time, while in silos, convection and diffusion interact to establish a consistent diffusion layer thickness. This research enhances the understanding of modified atmosphere techniques and their potential for sustainable pest management. It provides practitioners with valuable quantitative insights, paving the way for optimized modified atmosphere strategies in real-world agricultural contexts.

Background: Very low-calorie ketogenic diet (VLCKD) is associated with improvement of metabolic and cardiovascular disorders. We aimed to evaluate the effects of VLCKD in patients with Cushing’s disease (CD) as adjunctive therapy to treatment for primary disease. Methods: We evaluated clinical, hormonal and metabolic parameters in 15 patients with CD and 15 controls at baseline and after 1 week and 3 weeks of VLCKD and further 2 weeks of low-carbohydrate ketogenic diet (LCKD). Results: After 5 weeks of diet a significant decrease in BMI (p=0.002), waist circumference (WC) (p=0.024), systolic (p=0.015) and diastolic blood pressure (p=0.005), ACTH (p=0.026), cortisone (p=0.025), total (p=0.006) and LDL cholesterol (p=0.017), triglycerides (p=0.016), alkaline phosphatase (p=0.008) and a significant increase in HDL cholesterol (p=0.017), vitamin D (p=0.015) and oral disposition index (Dio)(p=0.004) was observed in CD. A significant decrease in BMI (p=0.003), WC (p=0.002), systolic (p=0.025) and diastolic (p=0.007) blood pressure and total cholesterol (p=0.026) and increase in HDL cholesterol (p=0.001) and DIo (p&lt;0.001) was observed in controls. Conclusions: The current study confirms that ketogenic diet is effective in improving metabolic disorders and shows that a nutritional approach may be combined with conventional CD therapy in order to improve metabolic and cardiovascular comorbidities.

FeZnNa@SiO2-C catalyst with graphitized carbon (GC) modified mesoporous SiO2 support metal nanoparticles was prepared by sol-gel method. The effect of adding metal Na and Zn promoters as a dispersion on the CO2 hydrogenation to low olefins was systematically studied. The results showed that Zn-Na, as a combination, promoted the absorption of CO2 and improved the conversion rate of CO2. Na as an alkaline substance can improve the absorption of more acidic CO2, improving the conversion rate of CO2 to 59.03%. Meanwhiles, addition of secondary metal Zn into Fe-based catalysts to form a surface alloy could alter the adsorption of CO2 and the activation of C-O bonds, inhibit the subsequent hydrogenation of olefins to paraffins, facilitate the reduction of Fe2O3 and the formation of active Fe5C2 species. From TEM and XRD, the formation of active Fe5C2 species was found, the selectivity of the target product was 41.07%. The deep hydrogenation of olefins is inhibited, by inhibiting their deep hydrogenations, the STY of C2=-C4= was raised again, up to 0.0436. However, the corresponding STY does not increase infinitely with the increase of Na content, and when the Na content to 6.4%, which can be shown higher CO2 hydrogenation catalytic performance. Compared with Fe@SiO2-C catalyst, Na and Zn promoted Fe-based catalysts prepared by modified sol-gel method, can be used directly for highly efficient CO2 hydrogenation to low olefins and thus will be more promising in the future.

In order to balance the conflicts among mass flow rate, total pressure ratio, adiabatic efficiency and stall margin in a low-bypass transonic fan, the optimization of the rotor blade is implemented in this study. An advanced 3D optimization design system is adopted, and flow diagnostic methods based on vorticity dynamics are employed to discuss the flow field. Results indicate that by controlling the blade camber line curvature, significant improvements in the aerodynamic performance for the fan stage are achieved, the total pressure ratio is increased by 1.90%, while the adiabatic efficiency and mass flow rate are increased by 4.45% and 5.82%, respectively. Vorticity diagnosis suggest that there exists a close link between performance parameters and vorticity parameters in the axial fan/compressor, both azimuthal vorticity and boundary vortex flux have significant influences on the stage performance. Moreover, the boundary layer separation is accompanied by the spike of entropy and static pressure, while the derivation/gradient of these flow parameters would also suffer drastic changes under the effect of shock wave. The vorticity parameters could provide detailed flow information about the on-wall flow with high accuracy, which provides the researchers with a novel method for the turbomachinery aerodynamic design and analysis.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Estrogens play a protective role during early life stages. However, endogenous 17β-estradiol (E2) can accelerate atherosclerosis progression in low-grade inflammatory conditions like established atherosclerosis. Our single-center cohort study assessed sex-specific associations of gonadal hormones with oxidative stress, inflammation, and myocardial injury markers in 111 patients (37% women) diagnosed with acute myocardial infarction (MI) between July 2011 and December 2013. Blood samples were collected within 48 hours of symptom onset, and we measured sex steroids (E2, total testosterone [T]), oxidized low-density lipoproteins, high-sensitive C-reactive protein (CRP), white blood cell counts (WBC), and cardiac enzymes (creatine kinase [CK], the CK Muscle-Brain fraction [CK-MB], and high-sensitive troponin T [hsTnT]). The SYNTAX score gauged coronary disease severity from coronary angiography results. In men with acute MI, peak cardiac enzyme levels were predicted by post-percutaneous coronary intervention (PCI) E2 plasma levels (OR 1.011, p=0.047 - CK; OR 1.018, p=0.013 - CK- MB; OR 1.019, p=0.005 - TnT), peak WBC count (OR 1.487, p=0.015 - CK ; OR 1,709, p=0,005 - CK- MB; OR 1.391, p=0.012 - TnT), and peak CRP plasma levels (OR 1.040, p=0.033 - CK; OR 1.024, p=0.029 - CK-MB; OR 1.063, p=0.006 - TnT). T levels and E2/T ratio were associated with post-PCI CRP in these men (OR 0.980, p = 0.024 - T, OR 1.010, p = 0.076 - CRP). For women, peak WBC was a marker of highest testosterone (OR 1.348, p = 0.062), and only WBC was a significant indicator of myocardial injury extent (OR 1.426, p=0.039 - CK; OR 1.384, p=0.036 - CK-MB; OR 1.299, p=0.048 - TnT). During acute MI, elevated endogenous estradiol levels correlate with myocardial necrosis severity in men, while in women, increased leukocyte levels indicate acute myocardial damage. Elevated plasma T is associated with increased WBC in women. In men, post-PCI plasma CRP specifically indicates endogenous T levels and E2/T ratio during the acute phase.

Total-body PET/CT scanners provide increased sensitivity, enabling the adjustment of imaging parameters by reducing injected activity or shortening acquisition time. This study aimed to evaluate the limitations of reduced [18F]FDG activity doses on image quality, lesion detectabil-ity, and quantification of lesion uptake in the Biograph Vision Quadra, as well as to assess the benefits of the recently introduced ultra-high sensitivity mode in a clinical setting. A number of 26 patients who underwent [18F]FDG-PET/CT (3.0 MBq/kg, 5 min. scan time) were included in this analysis. PET raw data was rebinned for shorter frame durations to simulate 5 min. scans with lower activities in high sensitivity (HS) and ultra-high sensitivity (UHS) modes. Image quality, noise, and lesion detectability (n=82) were assessed using a 5-point Likert scale. The co-efficient of variation (CoV), signal-to-noise ratio (SNR), tumor-to-background ratio (TBR), and standardized uptake values (SUV) including SUVmean, SUVmax, and SUVpeak were evaluated. Sub-jective image ratings were generally superior in UHS compared to HS mode. At 0.5 MBq/kg, le-sion detectability decreased to 95% (HS) and 98% (UHS). SNR was comparable at 1.0 MBq/kg in HS (5.7±0.6) and 0.5 MBq/kg in UHS (5.5±0.5). With lower doses, there were negligible reductions in SUVmean and SUVpeak, whereas SUVmax increased steadily. Reducing [18F]FDG activity to 1.0 MBq/kg (HS/UHS) in a total-body PET/CT provides diagnostic image quality without statistical-ly significant changes in uptake parameters. UHS mode improves image quality, noise, and le-sion detectability compared to HS mode.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

Smart grids are seeing an increase in renewable energy and an enormous introduction of advanced power electronics, increasing the number of disturbance sources. This requires improving the accuracy of measurement systems capable of acquiring data for use in power system monitoring applications. Rogowski Coils (RCs) and Merging Units (MUs) are being widely deployed in controlling, metering, and monitoring of digital power systems. Because the performance of digital measurement devices has a direct influence on power measurement accuracy, it is critical to perform a laboratory calibration of these measurement instruments before they are installed in any project. To determine the magnitude and phase displacement errors of the RC+MU under normal and abnormal operating conditions, this article presents a comprehensive laboratory digital calibration system constructed from precise, readily available commercial products such as a fluxgate current transducer and a National Instrument. In addition, the analysis of measurement chain is affected by sources of uncertainty is discussed. The tests yield findings that are consistent with the relevant standards.

The low-altitude quasi-periodic (LQP) E-region echoes observed with the upgraded HCOPAR located in Hainan Island of China (19.5°N, 109.1°E) are presented. With the interferometry technique, the interferometry equations can be developed to investigate the structures of the irregularities. The results show that the plasma structures of the LQP echoes with negative slope mainly drift southwestward almost horizontally, but they also drifted southeastward in some striations. According to the movement of the plasma structures, we find strong wind shear in the region where the LQP echoes are produced. Meanwhile, The periodicity of the LQP echoes may be related to the strength of the wind shear. It is proposed that the plasma structures are most likely produced by the Kelvin-Helmholtz instability.

The German government's ambitious goal of achieving CO2-neutrality by 2045 has prompted a focus on improving building insulation as a vital step toward energy efficiency. However, in this process, existing radiators and boilers are often left unchanged, leading to inefficiencies due to oversized heating systems. This paper presents various approaches to reduce the required radiator inlet temperature, drawing on data from 100 multifamily buildings. The approaches include heat reserve reduction, heat power shifting, uniform radiator usage, and heat requirement analysis. These approaches collectively aim to lower flow temperatures and decrease peak heat loads, reducing energy consumption, and minimizing waste in compliance with the user comfort temperature. The findings reveal that the application of these methods can lead to substantial temperature reductions, with an average decrease of 20.82 K and 7.28 K for the highest necessary flow temperature in the provided example. Furthermore, peak load reductions of 21.07% and 13.65% were achieved, demonstrating the potential to enhance energy efficiency. While each approach can be applied individually, their synergistic implementation can highly increase the efficiency of water to x heat pumps, due to the lower required flow temperatures.

A Gem-quality rubies and sapphires are often commercially heat treated at about 800°C or higher temperatures to enhance their colour and clarity, and hence quality. For this study, selected corundum samples containing diaspore- and goethite inclusions were heated step-by-step to a maximum of 1000 °C with the aim to monitor the dehydration and phase transformation of these oxyhydroxides to corundum and hematite during heating. Based on our experiments and in agreement with literature, the dehydration of diaspore in corundum occurs between 525 to 550 °C, whereas goethite transforms to hematite already between 300 and 325 °C. As both, diaspore and goethite are common inclusions in rubies, sapphires, and other corundum varieties, these dehydration reactions and phase transformations can be considered important criteria to separate unheated stones from heated ones, specifically in cases in which other methods (e.g. microscopy, FTIR) are unsuccessful.

In recent years, frequent occurrences of low temperature disasters due to global climate change have significantly impacted the normal growth of crops. Research has indicated that inorganic selenium (which is more toxic) can not only enhance the effects of low temperature stress but also increase selenium content on plants; however, there is a scarcity of studies investigating the impacts of organic selenium and nano-selenium on crops. In order to investigate whether organic selenium and nano-selenium can enhance low-temperature tolerance and increase selenium content in pak choi (Brassica chinensis var. pekinensis. cv. ‘Suzhouqing’), different concentrations (0, 5, 10, 20 mg L-1) of exogenous selenium were applied in this experiment to assess their effects on plant growth, nutritional quality and antioxidant properties. RNA-Seq technology was used to sequence the transcriptome of the leaves. Based on the transcriptome data, a Weighted Gene Co-expression Network Analysis (WGCNA) was employed to construct a network that associates with physiological traits related to stress resistance. Two highly correlated gene co-expression modules were identified, and within them, nine hub genes associated with endocytosis, antioxidant stress, absorption, transport, and metabolism of selenium were discovered. The results indicated that the beneficial effects on yield and total selenium content under low temperature were attributed to (1) protection of photosynthetic pigments for enhancing photosynthetic capacity by the up-regulation of LHca2, LHcb1, LHca1, LHcb4 in KEGG pathway: photosynthesis-antenna proteins; (2) activation of antioxidant system for efficient ROS homeostasis such as SOD, POD and CAT by the genes such as Superoxide dismutase, Monodehydroascorbate and (3) selenium absorption by endocytosis, seleninum transportation by ABC transporter gene family and selenium metabolism related genes such as Cysteine synthase, Glutaredoxin. These findings provide a foundation for further investigation into the molecular mechanisms underlying the effects of organic selenium and nano-selenium on cyanochloride production at low temperatures.

The stress concentrations have become common phenomenon of steel elements when arresting a fracture by implementing the crack stop hole (CSH) technique. Embedding the CSH with Carbon Fibre Reinforced Polymer (CFRP) enhance the fatigue life by delaying the fractures while achieving a stiffness recovery due to superior mechanical characteristics of CFRP material. Hence, low cyclic fatigue (LCF) behaviour of 162 strengthened and non-strengthened CSH specimens were examined in this context. These specimens were subjected to a range of 0 to10,000 fatigue load cycles with the frequency of 5 Hz. At the end of fatigue exposure, the average tensile strength was measured in each case. The average strength reductions in the range between 13% to 25% was noted in steel elements with CSH subjected to fatigue exposure. The application of a CFRP patch on CSH had effectively recovered the strength losses while enhancing the strength in the range between 32% to 45% with respect to the non-strengthened non specimens. The developed numerical model based on cyclic J-integral technique agrees with test results and is capable of predicting characteristics for this novel hybrid technique.

Low 25 OH vitamin D (25(OH)D) in preterm infants is a risk factor of bronchopulmonary dysplasia (BPD), but increased supplementation failed to demonstrate beneficial effect on BPD. In neonatal animal models, deficiency and excessive vitamin D exposure have been associated with increased mortality and lung histological alterations evocative of BPD. Our hypothesis is that 25(OH)D levels ≥ 120nmol/L is also a risk factor for BPD or death. This retrospective single-center cohort study included all infants born <31 weeks gestational age without major malformation with at least a determination of 25(OH)D <36 weeks corrected age and no determination <50 nmol/L. Routine 25(OH)D determination was performed at 1 month and monthly thereafter. A total of 175 infants were included. Infants with BPD or who died had a significantly lower term and weight, but a similar frequency of 25(OH)D ≥120nmol/L (50.5% vs 43.9%, p=0.53). The logistic regression identified weight (OR 0.997, 95%CI [0.995-0.998]) and term (OR 0.737, 95%CI [0.551-0.975]) as significantly associated with BPD or death; the occurrence of excessive 25(OH)D was not significantly associated (OR 1.029, 95%CI [0.503-2.093]). The present study did not demonstrate any significant association between excessive 25(OH)D after one month of age and BPD or death.

Growing incidence of myopia worldwide justifies the search for efficient methods of myopia prevention. Numerous pharmacological, optical, and lifestyle measures have already been utilized, but there remains a need to explore more practical and predictable methods for myopia control. This paper presents a review of the latest literature on preventing the progression of myopia using Defocus Incorporated Multiple Segments Spectacle Lenses (DIMSsl), Repeated Low-level Red-Light Therapy (RLRL), and the combination of low-dose atropine (0.01%) with orthokeratology lenses.

Greenhouse gas (GHG) emissions from human activities have climbed significantly above pre-pandemic levels and reached record highs that unequivocally accelerate global warming. Industry has a significant impact on climate change, emitting at least 21 % of global GHGs and making little overall progress toward its reduction until now. Reducing industry’s emissions requires coordinated action along the value chains in order to promote mitigation options, such as energy and material efficiency, circular material flows, and transformative changes within production processes. The authors analyzed the GHG emissions generated during the manufacturing of three different products of automotive suppliers located in Austria. Despite previous efforts toward an environmentally compatible fabrication, additional and significant reduction potentials were identified. These measures for product carbon footprint (PCF) reduction included the sourcing of low-carbon materials (which are already available on the market), more extensive use of renewable energy, and changes towards more resource efficient manufacturing processes and machinery. Depending on the materials used, the PCF can be reduced by up to 80 %. The findings serve to prepare for future PCF reporting regulations and illustrate reduction potentials to achieve future market advantages, especially when PCFs become an awarding criterion.

Background:This study evaluated the effect of low-level laser therapy on postoperative pain and wound healing in children undergoing primary molar extractions.Methods:40children,6-10years of age, systemically healthy, and had atraumatic extraction indications of bilateral primary molar teeth were included in the study. First session randomly selected tooth was extracted under local anesthesia. In the control group, only the clot formation on the socket was observed and photographed. Other group extraction's performed 2weeks later. The LLLT group treated with980nm wavelength Doctor Smile Wiser diode laser and photographed. Non-epithelialized surface measurements performed with the ImageJ program. Pain assessment was performed with Wong-Baker Pain Scale. Statistical analyzes were performed with SPSS software.Results: There was no statistically significant difference in Wong-Baker values(p&gt;0.05). The laser group had more '0' values on days 1 and7; same values as the control group were recorded on other days. In soft tissue healing 3rd day evaluations, non-epithelialized surface of laser socket was found to be smaller than control group, and measurement results were found to be statistically significant(p&lt;0.05). The other days' measurement results were not statistically significant(p&gt;0.05).Conclusions:Although LLLT not found to be very effective in reducing postoperative discomfort after extraction of primary molars, it provides better wound healing in extraction sockets.

The authors attempt to addresses the importance of timely detection and management of cervical intraepithelial neoplasia (CIN) to prevent cervical cancer. The study focuses on the potential of electrical impedance spectroscopy (EIS) as an adjunct to colposcopy, aiming to enhance the accuracy of identifying high-grade cervical lesions. Colposcopy, a widely used technique, exhibits variable sensitivity in detecting high-grade lesions, which relies on the expertise of the operator. The study's primary objective is to evaluate the effectiveness of combining colposcopy with EIS in detecting high-grade cervical lesions among patients initially diagnosed with low-grade CIN based on cytology. We employ a cross-sectional observational design, recruiting 101 women with abnormal cervical cytology results. The participants undergo colposcopy with acetic acid and subsequent EIS using the ZedScan device. The ZedScan results are categorized into color-coded probability levels, with red indicating the highest likelihood of high-grade squamous intraepithelial lesions (HSIL) occurrence. Results reveal that ZedScan exhibits a sensitivity rate of 89.5% and a specificity rate of 84% for detecting high-grade lesions. Colposcopy, on the other hand, records a sensitivity rate of 85.5% and a specificity rate of 92%. The agreement rate between ZedScan and biopsy is 79.2%, as indicated by a kappa coefficient of 0.71, while the agreement rate between colposcopy and biopsy is 74.3%, with a kappa coefficient of 0.71.

Previous studies on the mechanisms underlying willed actions reported that the premotor cortex may be involved in the construction of motor awareness. However, its exact role is still under investigation. Here we investigated the role of the dorsal premotor cortex (PMd) in motor awareness by modulating its activity applying inhibitory rTMS to PMd, before a specific motor awareness task (under three conditions: without stimulation, after rTMS and after sham stimulation). During the task, subjects had to trace straight lines to a given target, receiving a visual feedback of the line trajectories on a computer screen. Crucially, in most trials the trajectories on the screen were deviated and to produce straight lines, subjects had to correct their movements towards the opposite direction. After each trial, participants were asked to judge whether the line seen on the computer screen corresponded to the line actually drawn. Results show that participants in the no stimulation condition did not recognize the perturbation until 14 degrees of deviation. Importantly, active, but not sham, rTMS significantly modulated motor awareness, decreasing the amplitude of the angle at which participants became aware of the trajectory correction. These results suggest that PMd plays a crucial role in action self- monitoring.

The vibration response of soil is a key property in the field of agricultural soil tillage. Vibration components of tillage machinery are generally used to reduce tillage resistance and improve work efficiency, the pressure variation under low-frequency vibration will affect the fragmentation and dispersion of farmland soil. However, the gradient of pressure variation, frequency domain response, and effective transmission range are unclear. A new method based on DEM (Discrete Element Method) is presented to study the vibration response and pressure transmission under low-frequency vibration. Bench test results showed that peak pressure positively correlates with the vibration frequency and attenuates rapidly at the vibration distance of 100 to 250 mm. The results data were also selected to determine the simulation model parameters. Amplitude, vibration frequency, and soil depth were used as test factors in single-factor simulation tests, and their effects on the peak pressure, frequency domain response, and effective transmission distance were analyzed. The results showed a positive relationship between the peak pressure and the test factors. The peak pressure increases with a maximum gradient of 19.02 kPa/mm at a vibration distance of 50 mm. The amplitude, vibration frequency, and soil depth positively correlate with the dominant frequency amplitude. The main frequency is independent of amplitude and soil depth. At the vibration distance of 250 mm, the dominant frequency is approximately twice the vibration frequency at 7–11 Hz and approximately equal to the vibration frequency at 13–15 Hz. Multiple exponential functions were used to fit the peak pressure attenuation function, obtaining an effective transmission distance range of 347.15 to 550.37 mm for the 5kPa cut-off pressure. For a soil depth of 300 mm, the vertical shear wave diffusion angle is greater than the horizontal shear wave diffusion angle. The study clarifies the vibration response of soil under low-frequency vibration, which helps to design vibration type soil-engaging components of tillage machinery and match vibration parameters for energy saving and resistance reduction in soil tillage.

Controlling injection parameters is paramount when it comes to producing high-quality green parts using powder injection molding. This work combines experimental and numerical approaches to study the impact of injection parameters on mold in-cavity pressure and on the overall quality of green parts produced by low-pressure powder injection molding. The properties of two low-viscosity feedstocks (formulated from a water-atomized stainless-steel powder and wax-based binder system) were measured and implemented in an Autodesk Moldflow numerical model to quantify the molding pressures, which were finally validated using experimental real-scale injections. The results confirmed that an increase in mold temperature, an increase in feedstock temperature, and a decrease in solid loading decrease the mold in-cavity pressure, which was correlated with the feedstock viscosity. As a key result, real-scale injections confirmed that a minimum flow rate was required to avoid atypical high in-cavity pressure leading in several visual defects such as weld lines, flow marks, cracks, sinks, and incomplete filling. Due to differences in its thermal transfer properties, this flow rate threshold value decreases as the feedstock solid loading increases. For injection speeds higher than this value, the injection pressure measured experimentally was linearly correlated with the injection flow rate.

Pharmaceutical poisoning is a significant global public health concern, causing approximately 190,000 deaths yearly. This scoping review aims to comprehensively map the available literature on pharmaceutical poisoning and compare patterns between high-income countries (HICs) and low-middle-income countries (LMICs). A systematic search was performed across the following databases: Embase, PubMed, Cochrane Database of Systematic Reviews, Cochrane Central Register of Controlled Trials, and CINAHL. Studies included were from 1st January 2011 to 31st December 2020, in English, with full text available. Seventy-nine articles were included in the study; 21 were from LMICs and 58 were from HICs. The toxic exposure was largely intentional (77%) in LMICs and accidental (68%) in HICs. Drugs acting on the nervous system were responsible for 95% of toxicities worldwide with analgesics accounting for the largest subtherapeutic group in both LMICs (40%) and HICs (58%). Notable statistics were that HICs accounted for 99% of opioid overdoses, and LMICs accounted for 19% of anti-epileptic-induced toxicities. Overall, the medical outcomes of poisonings were generally worse in LMICs. The review provides possible interventions to target specific geographic locations, based on the trends identified, to reduce the burden worldwide. Many gaps within the literature were recognised, calling for more robust analytical research.

The National Institute of Justice reported that current methods for processing sexual assault samples have a high failure rate, with 60 to 80 percent of tested kits unable to produce usable DNA profiles. Even when samples test positive for male DNA, 34 percent of sexual assault kits (SAK) do not yield recovered male DNA after differential extraction. Less than 30% recovery of available sperm DNA contributes to this low success rate. The SpermX™ method (SX) has been shown to recover 80 percent or more of sperm DNA from sexual assault samples. An interlaboratory evaluation compared SX to standard differential extraction (DE) protocols. Mock samples with known ratios of female epithelial cells and sperm cells were processed using both methods. Results revealed that SX consistently provided CODIS up-loadable DNA profiles, even with as few as 25 sperm cells, whereas DE failed to produce usable results. On average, SX yielded a seven-fold increase in the recovery of unshared male alleles compared to DE. In conclusion, SX outperformed DE in recovering higher quantities of male DNA with minimal female carryover in sexual assault-type samples. This improved success rate in obtaining usable DNA profiles can significantly aid in solving sexual assault cases. Keywords: Differential extraction, Sexual Assault Kit (SAK), Sperm DNA, STRmix™, Combined DNA Index System (CODIS), Forensic DNA analysis, Low Sperm Samples, DNA Mixtures, Autosomal STR Analysis, SpermX.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

One of the strategies to reduce the contents of the low density lipoproteins (LDLs) in a blood is a hemoperfusion, in which case they are selectively retracted from plasma by an adsorber located outside the patient body. Recently, a photo-controllable smart surface was developed for this purpose characterised by high selectivity and reusability [C.Guo et al., ACS Applied Materials &amp; Interfaces 2022, DOI:10.1021/acsami.2c07193]. We present a mesoscopic model for such a setup involving the azobenzene-containing polymer brush and the model LDL particles. The latter comprise an uniform spherical core covered by a shell of elongated particles representing phospholipids. The system is studied using the coarse-grained molecular dynamics simulation. We examined the dependences of the binding energy on both the length of polymer chains and the grafting density of a brush, and established optimal conditions for the adsorption. These are explained by a competition between the concentration of azobenzenes and phospholipids in the same spatial region, flexibility of polymer chains, and excluded volume effects.

This research aims to develop an inexpensive ocean observation instrument with a project name is NOBEL (Nusantara Oceanography Backdoor Experiment Laboratory)-BOX. The device can be installed on all types of vessels and placed in a specific area to map the water conditions, providing accurate data for managing a marine area specifically to water quality. The principle of NOBEL-BOX is to attach sensors in a container connected to a microcontroller and then measure directly. The method employed includes experimental design, laboratory and field tests, and data evaluation to produce the necessary system and instruments. The design process involves the construction of the instrument and the fabrication of the device. This process includes creating three-dimensional sketches/drawings, designing microcontrollers and data transmission systems, and power capacity. The sensors attached to this device are surface water temperature, air temperature, salinity, dissolved oxygen, pH, and TDS. The testing phase includes data validation, testing of the device in the laboratory, and field testing. The laboratory and field tests showed that the device worked and provided data that can be used to analyze the seawater condition spatially and over time.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, aiming to protect the DFIG and power converters, and consequently, improve the system’ ability to ride-through faults. Further, the capacity of an energy storage device for transient suppression is estimated. Finally, simulation results show that the proposed approach is effective in achieving transient control objectives precisely and maintaining a stable grid connection during the faults.

Over a century ago, low-dose-rate (LDR) brachytherapy was introduced to treat prostate cancer (PCa). Since then, it has been widely applied worldwide, including in East Asia. LDR brachythera-py has been performed in 88 institutes in Japan. Beneficial clinical outcomes of LDR brachytherapy for intermediate-to-high-risk PCa have been demonstrated in large clinical trials. These clinical outcomes were achieved through advances in methods, such as urological precise needle puncture and seed placement, and the quantitative decision-making regarding radiological parameters by radiation oncologists. Combined use of LDR brachytherapy with other therapeutical modalities, such as external beam radiation and androgen deprivation therapy, for clinical risk classification of PCa has led to better anticancer treatment efficacy. In this study, we summarized basic LDR brachytherapy findings that should remain unchanged and be passed down in urology depart-ments. We also discussed the applications of LDR brachytherapy for PCa in various clinical settings, including focal and salvage therapies. In addition, we highlighted technologies associated with brachytherapy that are under development.

This study aimed to evaluate the proliferation and migration of fibroblast cells derived from chronic wounds and investigate the impact of low-level laser therapy (LLLT) on their growth and migration. A total of 60 dermal samples were obtained from three sites of chronic pressure ulcers and diabetic ulcers in 20 patients. Following collection in the operating room, the dermal samples were isolated using the procedure described by Freshney RI. Fibroblasts from the wound base (Site 1) exhibited a slow proliferation rate and a decrease in proliferative capacity. Fibroblasts from wound margins (Site 2) and adjacent healing skin (Site 3) could be successfully isolated and maintained for multiple generations without any morphological changes. Fibroblasts from chronic wounds at Sites 2 and 3 showed slower proliferation rates and reduced migration capabilities compared to normal dermal fibroblasts (control samples). The fibroblast cells were exposed to LLLT at different energy levels (2.5, 3, and 3.5 J/cm2). The laser-treated groups demonstrated a significantly higher increase in cell count compared to the control sample, with the highest increase observed at an energy level of 3 J/cm2. These findings suggest that LLLT at an energy level of 3 J/cm2 could effectively enhance fibroblast migration, indicating its potential as a therapeutic intervention for chronic wounds.

Glucose is an important carbon sources for microbial growth, and its content in infertile soils is essential for the growth of the bacterium. Since the mechanism of oligotrophic bacterium adaptation in barren soils is unclear, the research employed RNA Seq technology to examine the impact of glucose concentration on the low nutrient bacteria BS-G1 in soil affected by desertification. RNA-Seq revealed that differentially expressed genes（DEG）histidine metabolism, glutamate synthesis, HIF-1 signalling pathway, sporulation, and TCA cycle pathway of BS-G1 were significantly enriched in 0.015 g/L glucose concentration, compared with 10 g/L glucose concentration. DEG amino acids system, two-component system, Metal Ion Transport, and nitrogen metabolism system of B. subtilis BS-G1 were significantly enriched in 5 g/L glucose concentration, compared with 10 g/L glucose concentration. In addition, The present study identified its regulation pattern and key genes under the low glucose environment (7 mRNAs, 16 sRNAs). This study primarily investigates the variances in the regulatory pathways of oligotrophic bacteria BS-G1, which holds substantial importance in comprehending the mechanism underlying the limited sugar tolerance of oligotrophic bacteria.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

The study of velocimetry is important for characterizing and comprehending the effects of fluid flow, and the Particle Image Velocimetry (PIV) technique is one of the primary approaches for understanding the velocity vector field in a test section. Commercial PIV systems are expensive, with one of the main cost factors being high-speed camera equipment capable of capturing images at high frames per second (fps), rendering them impractical for many applications. This study proposes an evaluation of utilizing smartphones as image acquisition systems for PIV technique application. An experimental setup inspired by the known angular displacement of synthetic particles is proposed. A stepper motor rotates a plate containing an image of synthetic particles on its surface. The motion of the plate is captured by the smartphone camera, and the images are processed using PIVlab-MatLab® software. The use of two smartphones is assessed, with acquisition rates of either 240 fps or 960 fps and varying angular velocities. The results were satisfactory for velocities up to 0.7 m/s at an acquisition rate of 240 fps and up to 1.8 m/s at 960 fps, validating the use of smartphones as a cost-effective alternative for the PIV technique.

Background: Spinal pain is highly prevalent and in Spain it produces a very high economic cost and the scientific evidence supporting treatments shows low to moderate evidence for exercise. Therefore, the aim of this study was to assess the effectiveness of a therapeutic group exercise protocol in reducing pain intensity and disability in patients with spinal pain in primary health care setting. Methods: A total sample of 149 patients who suffered from chronic non-specific spinal pain. Patients received a therapeutic exercise protocol, including exercises of auto-mobilization of the neck and lumbar regions, as well as core stabilization exercises. Pain intensity and disability were evaluated before and after the therapeutic exercise protocol. Results: Statistically significant differences (P&lt;0.05) were shown for pain intensity and disability of patients with neck and low back pain with an effect size from moderate to large. Conclusions: A therapeutic exercise protocol may provide beneficial effects on disability and pain intensity in patients with chronic non-specific spinal pain, including neck and low back pain conditions. Clinicians should consider the use of self-administered exercise protocols, demonstrate great effectiveness, and be less costly.

Investigating the potential impact of composting and recycling waste on income distribution are crucial to promote a fairer and more sustainable fresh tomato supply chain (FTSC). Therefore, this study aims to explore the potential of gaining extra income from recycling tomatoes waste generated along the FTSC and to calculate the contribution of extra income from recycling tomato waste to reduce income inequality along the FTSC. Data were collected from 136 greenhouse tomato producers, 60 wholesalers, 18 exporters, 120 domestic retailers, 22 overseas retailers, and 3 recycling facilities in Türkiye. Marketing cost, absolute marketing margin, relative marketing margin and net profit margin were used when economically analyzing the FTSCs. Research results showed that the net profit share of the producer decreased associated with the increasing number of intermediaries. Research results also showed that revenue gained from composting and recycling of product loss and waste increased the welfare of greenhouse producer more than other supply chain actors. When taking into account the revenue from composting and recycling of wastes, producers increased their net profit by 9.85% at first FTSC, while that of second and third FTSCs were 8.29% and 9.21%, respectively comparing to the prevailing conditions. The contribution of extra revenue from composting and recycling of wastes to retailers was more comparing wholesaler and exporter. Retailers and wholesalers gaining from recycling in domestic FTSCs was more comparing to overseas one. Close cooperation between producers, wholesalers, exporters, retailers, and recycling facilities is essential for the effective implementation of waste recycling initiatives. Organizing the training and education programs focused on waste management can increase the extra income of producers and active intermediaries in FTSC from composting and recycling tomato wastes. Offering financial incentives, grants, or subsidies can encourage producers and other actors within the supply chain to adopt waste recycling practices. Continuous research and innovation are crucial in identifying and developing new technologies, processes, and strategies to minimize food loss and waste. Dominating fair-trade practices to ensure that all FTSC actors may balance the income distribution among FTSC actors.

Logistics industry has been found to be among the key sources of carbon emission. In Vietnam logistics industry, there is a considerable difference between the number of foreign and Vietnamese firms as well as the proportion of markets that they are taking. This study is to research the low-carbon emission measures conducted by domestic and foreign invested logistics service providers (LSPs) and compare the results of the two groups. Both qualitative and quantitative approaches are applied. Literatures in relevant fields are reviewed and expert opinions are taken for structuring a questionnaire which was later distributed to 279 LSPs, with 166 returned and 159 being valid for data calculation. The results imply that there are differences in extension of applications of low-carbon practices between foreign and domestic firms. Except for transport mode switch and energy-saving lighting, the other practices witness that adoption levels of foreign LSPs are higher than their counterparts, which is possibly thanks to their global operation, more comfortable capital resources and awareness level of green initiative necessity. In conclusion, a comparison between the application conducted by foreign-invested firms and domestic ones, which has not been investigated before, was made.

Background: The mechanisms underlying the effect of estradiol (E2) on low-density lipoprotein cholesterol (LDL-C) levels are not completely understood, although a role for proprotein con-vertase subtilisin/kexin type 9 (PCSK9) has been proposed. We aimed to investigate the association between levels of E2, PCSK9 and lipid parameters in premenopausal women undergoing in vitro fertilization (IVF). Methods: Healthy women undergoing IVF in the Department of Obstetrics and Gynecology of the University General Hospital of Ioannina were recruited. Levels of E2, pro-protein convertase subtilisin/kexin type 9 (PCSK9), total cholesterol (TCHOL), high-density lip-oprotein cholesterol (HDL-C), LDL-C, and triglycerides (TGs) were measured 10 days after ovarian depression (E2min) and 7 days after ovarian stimulation (E2max). Results: A total of 34 consecutive healthy women aged 38 (26-46) years old who underwent a full IVF cycle were included. E2 levels increased by 329.6% from E2min to E2max (108 [47-346] to 464 [241-2471] pg/mL, p<0.05). At the same time, serum PCSK9 levels significantly decreased by 30.8% (245 ± 80 to 170 ± 64 ng/mL, p<0.05). No significant changes in TCHOL, LDL-C, TGs and HDL-C were found (-0.4%, -3.8%, -2.2%, and +5.3%, p >0.05). Conclusions: The increase in endogenous E2 production during an IVF cycle was associated with a significant decrease in serum PCSK9 levels during a 7-day period.

Disseminated or military tuberculosis (TB) is defined as the presence of at least two non-contiguous sites of Mycobacterium tuberculosis, occurring as a result of progressive primary infection, reactivation and spread of a latent focus or due to iatrogenic origin. Disseminated TB represents a life-threatening condition, especially in at-risk children and when the diagnosis and treatment are delayed. We report on a case of a 3-year old boy who presented with long-lasting unrecognised disseminated TB that was successfully managed in a low-resource setting.

Genetic adaptation of Hermetia illucens (BSF) to suboptimal single sourced wastes can open new perspectives for insect production. Here, four replicate BSF lines were maintained on a single sourced, low-quality wheat bran diet (WB) or on a high-quality chicken feed diet (CF) for 13 generations. We continuously evaluated evolutionary responses in several performance traits to rearing at the two diets. Subsequently, we tested responses to interchanged diets, i.e. of larvae that had been adapted to low-quality feed and to high quality feed and vice versa to evaluate costs associated with diet adaptation. BSF were found to experience rapid adaptation to the diet composition. While performances on WB diet were always inferior to CF diet, the adaptive re-sponses were stronger to the former diet. This stronger response was likely due to stronger se-lection pressure experienced by BSF fed on the low-quality single sourced diet. The interchanged diet experiment found no costs associated with diet adaptation but confirmed diet adaptation for the larval biomass and insect frass traits for the WB diet treatment. Our results revealed that BSF can rapidly adapt to diet through evolutionary responses, which has potential to be utilized to produce lines tailored to specific diets.

The unreliable prediction of the low frequency components from inverted acoustic impedance causes uncertainty in quantitative seismic interpretation. To address this issue, we first calculate various seismic and geological attributes that contain low frequency information, such as relative geological age, interval velocity, and integrated instantaneous amplitude. Then, we develop a method to predict the low frequency content of seismic data using these attributes, their high frequency components, and recurrent neural networks. Next, we test how to predict the low frequency components using stacking velocity obtained from velocity analysis. Using all the attributes and seismic data, we propose a supervised deep learning method to predict the low frequency components of the inverted acoustic impedance. The results obtained in both synthetic and real data cases show that the proposed method can improve the prediction accuracy of the low frequency components of the inverted acoustic impedance, with the best improvement in a real data example of 57.7% compared with the impedance predicted using well log interpolation.

This research delves into the impact of complex low-speed wake flow structures on the aerodynamic characteristics of objects downstream. It employs the proper orthogonal decomposition (POD) method and the domain precursor simulation method to compare traditional methods and validate this approach. The study generates several flow structures of parallel dual-cylinder wakes with different scales and spacing. The variations in the aerodynamic coefficient of three downstream objects at various times passing through wakes of varying scales are appropriately compared and analyzed. The study establishes that the wake with a cylinder spacing of G=1.5 has a more compact and concentrated modal structure than that with a cylinder spacing of G=0.35. Smaller objects are more responsive to the wake flow structure with a spacing of G=1.5, whereas larger objects respond more to the flow structure with a spacing of G=0.35. The achieved results also reveal that the aerodynamic force coefficients of objects passing through the wakefield at different times are closely related to the temporal characteristics of the wake flow structure with different scales.

Worldwide, 200 million children experience disability, with the vast majority living in low and middle-income countries. The United Nations Convention on the Rights of the Child (CRC) places great importance on the rights of all children for the opportunities for survival, growth, health, and development. A subsequent document, the UN Convention on the Rights of Persons with Disabilities (CRPD) identifies children with disabilities as rights bearers, who should be considered in all policies and programming worldwide. Nigeria, in 1991 and 2010 ratified the CRC and the CRPD respectively. Nonetheless, knowledge of the extent to which their disability and child-directed policies are considered by these two key conventions remains limited. This study examined the extent to which Nigeria’s current disability and childhood policies have integrated the two normative frameworks from the UN. Using a structured search of databases and Nigerian federal and state government websites, we conducted a policy review to identify their disability and child-related disability policies. We also included the CRC and CRPD reports submitted by the Nigerian government to the United Nations Office of the High Commissioner for Human Rights (OHCHR) (2008 &amp; 2010 cyclical year). A thematic analysis, based on the CRC and CRPD report, identified the following six themes: participation, support systems, awareness-raising, factors associated with adherence to the CRC, laws &amp; rights, and services. The review showed that the available Nigerian disability policies were federal, with some state policies which aligned with the CRC and CRPD. Also identified was the lack of disability policies specific to children and their families. We concluded that, to ensure proper inclusion of the rights of all children, including those with disabilities, in Nigeria there is a need for a more optimal uptake of recommendations of the CRC and CRPD as laid out by the UN.

With technological transformations such as big data, blockchain, artificial intelligence, and cloud computing, digital techniques are penetrating the field of finance. Digital finance is a resource-saving and environmentally friendly innovative financial service. It shows great green attributes and can drive the flow of financial resources towards environmentally friendly enterprises, thereby promoting green and low-carbon development. This paper investigates the effects of digital finance on green and low-carbon cyclic development and the mechanism. First, the level of green and low carbon cyclic development in China is estimated from multiple aspects based on the panel data of 31 provinces by using the spatio-temporal range entropy weight method. Then, the working mechanism of digital finance on green and low carbon cyclic development is revealed by performing empirical tests based on panel regression models, mediating effect models, and threshold models. Finally, the effects of digital finance and conventional variables on green and low-carbon cyclic development are investigated by using a random forest model and a CatBoost model in based on the machine learning. The results show that digital finance has significant positive effects on green and low-carbon cyclic development, and technological innovation plays a key role in the effects of digital finance on green and low-carbon cyclic development; meanwhile, the driving effect of digital finance on green and low carbon cyclic development shows nonlinear features with increasing “marginal effect”; besides, both digital finance and conventional factors have significant impacts on green and low carbon cyclic development. This study provides an empirical basis and path reference for digital finance to achieve “carbon peak, carbon neutralization” in China.

This paper introduces an advanced method that integrates contingent valuation and machine learning (CVML) to estimate residents’ demand for reducing or mitigating environmental pollutions and climate change. To be precise, CVML is an innovative hybrid machine-learning model, and it can leverage a limited amount of survey data for prediction and data enrichment purposes. The model comprises of two interconnected modules: Module I, an unsupervised learning algorithm, and Module II, a supervised learning algorithm. Module I is responsible for grouping the data into groups based on common characteristics, thereby grouping the corresponding dependent variable, whereas Module II is in charge of demonstrating the ability to predict and the capacity to appropriately assign new samples to their respective category based on input attributes. Take a survey on the topic of air pollution in Hanoi in 2019 as an example, we found that CVML can predict households’ willingness– to– pay for polluted air mitigation at a high degree of accuracy (i.e., 98%). We found that CVML can help users reduce costs or save resources because it makes use of secondary data that is available on many open data sources. These findings suggest that CVML is a sound and practical method that could be widely applied in a wide range of fields, particularly environmental economics and sustainability science. In practice, CVML could be used to support decision-makers in improving the financial resources to maintain and/or further support many environmental programs in years to come.