The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

Heavy metals constitute pollutants particularly common in air, water, and soil. They are present in both urban and rural environments, on land and in marine ecosystems, causing serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. Detection, though especially quantification, is a systematic process as monitoring of their levels needs to be carried out at regular intervals since there is often seasonal variation. The need for rapid and low-cost determination of metals is therefore considerable. In the present study atomic absorption spectroscopy (AAS), using a flame or graphite furnace, and square wave anodic stripping voltammetry (SWASV), using a bismuth thin film electrode, a sensitive voltammetric method is being compared and analytically validated. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique while anodic stripping voltammetry is being criticized for its applicability in complicated sample matrices such as soil samples. This sample-handling challenge is being investigated in the present study. The results show that both methods AAS and ASV were satisfactorily correlated and showed that the concentration of metals is lower than the limit values, but with increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of the city is necessary and a matter of great importance. Regarding Cd, the detection limits of Cd are lower compared to those of AAS when using the graphite furnace, while an overestimation was noted when using flame-AAS in comparison with those found with SWASV. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, we applied a dsDNA-modified electrode which can be used in the speciation analysis of Cu(I) and Cu(II). The changes in the characteristic peaks of guanine and adenine can be applied in the redox speciation analysis of copper in soil which represents an issue of great importance.

The paper describes the new method for image compression based on coordinated group signal transformation. The algorithm is a type of difference coding. Coordinated processing significantly simplifies the difference signal conversion scheme using a single group codec for all signals. The described method considers color channels as correlated signals of a multi-channel communication system. The specifics of the processed data required modification of the coordinated group processing algorithm. First, we changed how to calculate the difference signals to prevent data loss. Secondly, the group codec was supplemented with a neural network to improve the quality of reconstructed images. We considered the following types of neural networks: fully connected, recurrent, convolution, and convolution in the Fourier space. Based on the simulation results, it is best to use fully connected neural networks if the goal is to minimize processing delay time. These networks have a response time of 13 ms. On the other hand, if the priority is to improve quality in cases where delays are not critical, then convolution neural networks in the Fourier space should be used. These networks have a response time of 140 ms and are of significant interest.

Currently there are fewer depth models applied to pepper picking detection, while the existing generalized neural networks have problems such as large model parameters, long training time, and low model accuracy.In order to solve the above problems, this paper proposes a Yolo-chili target detection algorithm for chili pepper detection. First, the classical target detection algorithm yolov5 is used as a benchmark model, and an adaptive spatial feature pyramid structure combining the attention mechanism and the idea of multi-scale prediction is introduced to improve the model's detection effect on occluded peppers and small target peppers. Secondly, a three-channel attention mechanism module is introduced to improve the algorithm's long-distance recognition ability and reduce the interference of redundant testers. Finally, the quantized pruning method is used to reduce the model parameters and realize the lightweight processing of the model. Applying the method to the homemade chili pepper dataset, the AP value of chili pepper reaches 93.11%; the accuracy rate is 93.51% and the recall rate is 92.55%.The experimental results show that yolo-chili is able to achieve accurate and real-time pepper detection under complex orchards.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

With recent advancements in network technology and spread of Internet, use of social network services and Internet of Things devices has flourished, leading to a continuous generation of large volumes of graph stream data, where changes, such as additions or deletions of vertices and edges occur over time. Additionally, owing to the need for efficient use of storage space and security requirements, graph stream data compression has become essential in various applications. Even though various studies on graph compression methods have been conducted, most of them do not fully reflect the dynamic characteristics of graph streams and complexity of large graphs. In this paper, we propose a compression scheme using provenance data to efficiently process and analyze large graph stream data. It obtains provenance data by analyzing graph stream data and builds a pattern dictionary based on this to perform dictionary-based compression. By improving the existing dictionary-based graph compression methods, it enables more efficient dictionary management through tracking pattern changes and evaluating their importance using provenance. Furthermore, it considers the relationships among sub-patterns using an FP-tree and performs pattern dictionary management that updates pattern scores based on time. Our experiments show that the proposed scheme outperforms existing graph compression methods in key performance metrics, such as compression rate and processing time.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

Elastic yarns are the key component of high-performance compression garments. However, it remains a challenge to fabricate anti-fatigue yarns with high mechanical force and long elongation for generating compression garments with prolonged wear. In this paper, we report the development of anti-fatigue double-wrapped yarns with excellent mechanical properties by wrapping high-denier Spandex with nylon filaments in opposite twists. In particular, 560D high-denier Spandex as the core was untwisted which can maximumly reduce the interaction between the core and wrapping filaments, enabling high elongation of the double-wrapped yarns. In addition, we chose 70D nylon filaments with a tensile force of 387.40 ± 8.82 cN as the wrapping materials to provide sufficient force for double-wrapped yarns. Notably, opposite twists were induced for the inner and outer wrapping filaments to achieve a balanced stable yarn structure. By systematically optimizing manufacturing parameters including inner wrapping density, outer wrapping density, taking-up ratio, and drafting ratio, we obtained double-wrapped yarn with excellent tensile force (952.00 ± 24.03 cN) and elongation (357.28% ± 9.10%). Notably, the stress decay rate of optimized yarns was only 12.0% ± 2.2%. In addition, the optimized yarn was used as the weft-lining yarn for generating weft-lined fabrics, the elastic recovery rate of the obtained fabric was only 2.6% after cyclic stretching, much lower than the control fabric. Our design of anti-fatigue double-wrapped yarns could be widely used for fabricating high-performance compression garments.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

Background:Fontan completion is the last stage of univentricular repair, which drains the inferior vena cava against gravity to a higher-pressure pulmonary arterial circulation. The passivity and anti-gravity nature of this circulation render a failing Fontan, not an uncommon encounter, twenty years ago, Rodefeld and colleagues, decided to explore the feasibility of vascular pumps to support the passive nature of Fontan circulation, and since then, trials are still ongoing, and we aimed through this review to wrap up the results of these trials. Methods:A literature review has been conducted, to identify any in vivo or in vitro trial of a Fontan assist device. Several outcome parameters determined whether the trial will be included or not in this review, including, the flow rate of a pump if applicable, the number of compressions per minute if a compression device has been used, the resultant flow rate, the inferior and superior vena cava pressures, associated with each setting of the respective device, and any evidence of hemolysis or clotting within the circuit. Results:A total of ten trials have been included, with 23 different settings. Three designs have been identified, out of which two fall within the pump design, namely the connecting chamber and the intravascular pump designs; only one trial explored the possible use of a compression device. The commonest design encountered in in-vivo trials was the intravascular pump (67%). No reports of significant hemolysis or thrombosis were found. An increasing flow rate beyond 5L/min was associated with a negative outcome in the connecting chamber design, increasing upstream pressure in the SVC, while intravascular pumps did not display this limitation. Conclusion:Univentricular heart patients are a relatively small population, with very extensive needs, despite twenty years of trials, no study has yet concluded the optimal design or settings for a Fontan assist device. In this review, we identified that the intravascular pump remains the most practical design, due to its easy mode of insertion, and that it is not faced with the limitation or risk of increasing upstream resistance. There is still a long way to conclude its use as other designs such as compression devices have not yet been fully studied.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Relative to several model bacteria, the ethanologenic bacterium Zymomonas mobilis is shown here to have an elevated resistance to exogenous antimicrobial peptides (AMPs) – both, with regard to peptide bulk concentration in the medium, and the numbers of peptide molecules per cell. By monitoring integration of the AMPs in the bacterial cell membrane and observing the resulting effect on membrane energy-coupling, it is concluded that the membranotropic effects of the tested AMPs in Z. mobilis and in Escherichia coli are comparable. The advantage of Z. mobilis over E. coli apparently results from its uncoupled mode of energy metabolism that, in contrast to E. coli, does not rely on oxidative phosphorylation, and hence, is less vulnerable to disruption of its energy-coupling membrane by AMPs. It is concluded that the high resistance to antimicrobial peptides (AMPs) observed in Z. mobilis not only proves crucial for its survival in its natural environment but also offers a promising platform for AMP production and sheds light on potential strategies for novel resistance development in clinical settings.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

Even though inhalation dosimetry is determined by three factors (i.e., breathing, aerosols, and the respiratory tract), the first two categories have been more widely studied than the last. Both breathing and aerosols are quantitative variables that can be easily changed, while respiratory airway morphologies are difficult to reconstruct, modify, and quantify. Despite several methods are available for model reconstruction and modification, developing an anatomically accurate airway model and morphing it to various physiological conditions remains labor-intensive and technically challenging. The objective of this study is to explore the feasibility of using an adjoint-CFD model to understand airway shape effects on vapor deposition and control vapor flux into the lung. A mouth-throat model was used, with the shape of the mouth and tongue being automatically varied via adjoint morphing, and the vapor transport being simulated using ANSYS Fluent coupled with a wall absorption model. Two chemicals with varying adsorption rates, Acetaldehyde and Benzene, were considered, which exhibited large differences in dosimetry sensitivity to airway shapes. For both chemicals, large shape deformations were explored to find the maximal possible morphing; both the maximal and intermediate deformations were simulated for morphology parametric studies. Results show that changing the mouth-tongue shape can alter the oral filtration by 3.2% for Acetaldehyde and 0.27% for Benzene under a given inhalation condition. This study demonstrates that the hybrid adjoint-CFD approach can be a practical and efficient method to investigate morphology-associated variability in inhalation dosimetry of vapors and nanomedicines.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

In this work, two plasmonic structures with two different periodic nanostructures (nanodisk and nanostrip arrays) separated from the gold layer by an ultrathin dielectric Al2O3 layer are proposed, and their optical properties are simulated as 3-dimensional models using COMSOL Multiphysics software tool. The optical responses, such as the amplification of the electric field and the scattering, absorption and extinction cross sections of the two structures, are investigated and compared. The results show that both structures show strong field enhancement in their gap layer, and the structure with the periodic array of metal nanodisks shows stronger field enhancement and larger absorption, extinction, and scattering cross sections in its dipole resonance wavelength, which is defined as a bright plasmonic mode. In addition, some weaker resonant modes are observed for both structures and the reason for their generation is dis-cussed. The analysis of different possible modes in such structures is crucial for their application in various fields.

We demonstrate a proof-of-principle of simple all-solid-state post-compression setup for low energy, high repetition rate laser pulses, where spectral broadening was performed using a combination of highly nonlinear bulk materials in a simple single pass geometry. 75 fs, 210 nJ pulses from an amplified 76 MHz, 15.7 W Yb:KGW oscillator after sequential spectral broadening in ZnS and YAG samples of 2 mm and 15 mm thickness, respectively, were compressed to 37 fs by means of Gires–Tournois interferometric mirrors. The post-compressed pulses with an average power of 11.47 W demonstrated reasonable spatial-spectral homogeneity of the beam with the spectral overlap parameter V>83% and good beam quality with Mx2=1.28 and My2=1.14.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

Different types of resonators are used to create acoustic metameterials and metasurfaces. Recent studies focused on the use of multiple resonators of dipole, quadrupole, octupole and even hexadecapole types. This paper considers the theory of an acoustic metasurface, which is a flat surface with a periodic arrangement of multiple resonators. The sound field reflected by the metasurface is determined. If the distance between the resonators is less than a half the wavelength of the incident plane wave, the far field can be described by a reflection coefficient that depends on the angle of incidence. This allows to characterize the acoustic properties of the metasurface by a homogenized boundary condition, which is a high order tangential impedance boundary condition. The tangential impedance depending on the multiple order of the resonators is introduced. In addition, we analyze sound absorption properties of these metasurfaces, which are a critical factor in determining their performance. The paper presents a theoretical model that accounts for the multiple orders of resonators and their impact on sound absorption. The maximum absorption coefficient for a diffuse sound field, as well as the optimal value for the homogenized impedance, are calculated for arbitrary multipole orders.

Patients with metastatic epidural spinal cord compression (MESCC) and favorable survival prognoses may benefit from radiation doses exceeding 10 x 3.0 Gy. In a multi-center phase 2 trial, patients receiving 15 x 2.633 Gy (41.6 Gy10) or 18 x 2.333 Gy (43.2 Gy10) were evaluated for local progression-free survival (LPFS), motor/sensory functions, ambulatory status, pain, distress, toxicity, and overall survival (OS). They were compared (propensity score adjusted Cox regression) to a historical control group (N=266) receiving 10 x 3.0 Gy (32.5 Gy10). In the phase 2-cohort, 50 (of 62 planned) patients were evaluable for LPFS. Twelve-month rates of LPFS and OS were 96.8% and 69.9%, respectively. Motor and sensory functions improved in 56% and 57.1% of patients, and 94.0% were ambulatory following radiotherapy. Pain and distress decreased in 84.4% and 78.0% of patients. Ten and two patients experienced grade 2 and 3 toxicities, respectively. Phase 2 patients showed significantly better LPFS than the control group (p = 0.039) and a trend for improved motor function (p = 0.057). Ambulatory and OS rates were not significantly different. Radiotherapy with 15 x 2.633 Gy or 18 x 2.333 Gy was well tolerated and appeared superior to 10 x 3.0 Gy.

A novel concept of a finned piston system is presented and analyzed where the compression heat is continuously extracted from the compression chamber. The resulting compression characteristic moves in direction of an isothermal process, reducing so the temperature of the compressed fluid in the compression chamber and reducing the necessary mechanical work for the process. The finned piston concept consists in an integrated heat exchanger inside of the chamber and being constituated of imbricated flat fins placed on the stator part and on the mobile piston. The internal heat exchange surface is strongly increased in comparison with a classical piston/cylinder. The energetic performance of the new system is evaluated with the help of simulation. Pressures, forces and temperature of the compressed gas are simulated as well as the mechanical work needed. The different curves are compared with adiabatic and isothermal characteristics.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Docosahexaenoic acid (DHA) is an essential fatty acid (FA) with proven health effects, whom bioavailability improvement is becoming a public health issue. Unlike fish oils, the bioavailability of DHA from microalgal (A) has not been fully assessed, particularly with regard to the molecular structuring capabilities offered by A-oil. We explored the impact of 5 formulas rich in DHA, different by i) the molecular structure: ethyl ester (EE) or monoglyceride (MG) or Triglyceride (TG) and ii) the supramolecular form: emulsified TG or TG+phospholipids (blend PL), on the lymphatic kinetics of DHA absorption and the lipid characteristics of resulting lipoproteins. We demonstrated that in rat, the DHA absorption of the conventional A-DHA TG structure was more effective than the EE structure (+ 23%). More, the A-DHA MG and A-DHA Emulsion were the most favourable DHA-vectors (AUC: 89% and +42%, respectively), thanks to an improved lipolysis. The A-DHA MG and -Emulsion presented the richest DHA content in TG (+40%) and PL (+50%) of lymphatic chylomicrons, which could impact the metabolic fate of DHA. We concluded that structuring A-DHA in TG or EE would be more prone for tissue and hepatic metabolism whereas in A-DHA MG and A-DHA Emulsion could target nerve tissues.

Keywords: Evanescent field; photonic sensor; optical waveguide; light-matter interaction; absorption; mid-infrared.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

Background: Restorative materials might significantly affect load transmission at peri-implant bone. The aim of the present study is to evaluate the shock absorption capacity of two different polymeric materials to be used as frameworks for implant-supported prostheses. Methods: A masticatory robot was used to compare the shock absorption capacity of polyether-ketoneketone (PEKK) Pekkton®ivory (Cendres+Mètaux) and glass fiber-reinforced composite (GFRC) TRINIATM (Bicon). Five identical sample crowns for each of the materials was tested un-der the same conditions described in previously published papers (Menini et al. 2013). Forces transmitted at the simulated periimplant bone were recorded and statistically analysed. Results: The statistical analysis of forces transmitted at the simulated dental implant revealed significant differences between all the materials tested and significant differences with the mate-rials tested in a previously published paper (Menini et al. 2013: zirconia, glass ceramic, composite resin, acrylic resin). Only differences between PEKK and veneered PEKK and between PEKK and one of the previously tested composite resins were not statistically significant. PEKK samples demonstrated significantly greater shock absorption capacity compared to GFRC. Conclusions: PEKK revealed optimal shock absorption capacity. Further studies are needed to evaluate its efficacy in case of long span prostheses with reduced prosthetic volume.

The automotive industry needs to improve energy efficiency rapidly to achieve carbon neutrality while creating a safe, secure, comfortable driving environment for customers. Porous sound-absorbing materials and porous thermal insulators are typically used to satisfy these requirements despite limitations in mass and space. While these porous materials are similar, the microstructures they offer for high performance differ in the size and connectivity of their fluid phases, which enhances the difficulty of achieving excellent sound absorption and thermal insulation in the same material. In this study, a hydrophobic cellulose nanofiber–poly(methylsiloxane) xerogel composite was developed using computational microstructure modeling. This porous material has high porosity and excellent thermal insulation and sound absorption properties.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

The pollution caused by nitrogen dioxide is a major environmental problem in China. This study introduces a new type of atmospheric trace gas remote-sensing instrument, an airborne fiber imaging spectrometer. This spectrometer has a spectral range of 300–410 nm and works in push-broom mode with a 30° field of view on a flight path. Flight experiments were conducted on December 30, 2022 and January 5, 2023, covering heavily polluted areas of east of Beijing and Tangshan. This equipment obtained the density distribution of NO2 over the flight area. The results showed that pollution was mainly concentrated in the Caofeidian area and at the power station in the north, and the main source of pollution was anthropogenic. Satellite and airborne data near the pollution points were compared, and the two datasets showed a positive correlation with a correlation coefficient of 0.78 and 0.7, on the two days, respectively. This study demonstrates the capability of an airborne fiber imaging spectrometer for NO2 regional emission remote sensing and identifying the pollution points.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

Experimental tests and numerical analyses were carried out on short, thin-walled channel columns with modified cross-sectional shape. The columns were loaded with an axial compressive force applied at the center of gravity of the cross section. Tests were carried out on a universal testing machine, while numerical analyses were performed in ANSYS software. The purpose of the tests was to determine the values of critical forces for the compressed columns and to determine the values of maximum forces at which failure of the columns occurs. Critical forces were determined based on the strain-averaged method. Based on the study, it was found that the strength and resistance to loss of stability of columns is primarily affected by their stiffness, and therefore by the shape of the cross-sections. In addition, for short columns, it seems more important to determine the value of maximum forces than the values of critical forces.

Cadmium (Cd) is an environmental toxicant of worldwide public health significance. Diet is the main non-workplace Cd exposure source other than smoking. The intestinal absorption of Cd involves the transporters for iron, zinc, copper, and calcium. These metal transporters essentially determine the body burden of Cd because only 0.001-0.005% of Cd accumulated in the body can be excreted in urine each day. The International Agency for Research on Cancer listed Cd as a human lung carcinogen. Current evidence, however, suggests that environmental Cd may increase the prevalence of many types of cancer, notably lung, liver, breast, pancreas, and kidney. A two-year bioassay that mimics a lifelong exposure demonstrates Cd caused neoplasms in multiple tissues of mice. Also, several non-tumorigenic human cell lines underwent malignant cell transformation, when they were exposed to a sublethal dose of Cd for a prolonged time. Cd does not directly damage DNA, but it can profoundly affect gene expression through its interactions with various proteins, and Cd can thus be viewed as a transcription modulator. The present review highlights epidemiological studies that connected an enhanced risk of various neoplastic diseases to chronic exposure to environmental Cd. Special emphasis is on the impact of body iron stores on the absorption rate of Cd, and its implications for breast cancer prevention in highly susceptible subpopulation groups of women. Resistance to cell death and other cancer phenotypes acquired during Cd-induced cancer-cell transformation, under in vitro conditions, are briefly discussed. The potential role for ZnT1 efflux transporter in cellular acquisition of tolerance to Cd cytotoxicity are highlighted.

This study examines the absorption and concentration of anthracene (AN) in the garden radish. Studies were conducted to grow radishes from the sowing stage in soil contaminated with AN, and to grow radishes in soil contaminated with AN following maturity (27 days after sowing). For the growth in AN-containing soil from sowing onward, AN levels immediately after seeding ranged from 12,500-36,300 ng/g-ww. AN concentrations during growing period ranged from 7140-16,000 ng/g-ww in soil and from 38.2-2160 ng/g-ww in radish, respectively. For the growth in AN-containing soil after maturity, AN concentrations in soil and radish ranged from 9560-22,100 ng/g-ww and 342-2270 ng/g-ww. The concentrations of AN in the roots and leaves had a higher density than those in the stems. In these experiments, positive relationships between AN levels in soil and radishes were observed. It is inferred that the greater the degree of soil contamination, the greater the effect on the amount of AN assimilated by the radishes. The concentration ratio (radish-to-soil; Cr/Cs) decreased exponentially with days since AN application. This indicates that the concentration ratio is affected by time in contact with AN. According to the results for the change over time of Cr/Cs and contents by radish part, it is thought that AN in the soil has good absorption through the roots to circulate within the organism, and is preferentially distributed and accumulated in the roots and leaves, which have high organic matter content.

Keywords: Spine surgery 1; Metastatic spinal cord compression 2; Spinal metastasis 3; Cancer treatment.

We extend Ziv and Lempel's model of finite-state encoders to the realm of lossy compression of individual sequences. In particular, the model of the encoder includes a finite-state reconstruction codebook followed by an information lossless finite-state encoder that compresses the reconstruction codeword with no additional distortion. We first derive two different lower bounds to the compression ratio that depend on the number of states of the lossless encoder. Both bounds are asymptotically achievable by conceptually simple coding schemes. We then show that when the number of states of the lossless encoder is large enough in terms of the reconstruction block-length, the performance can be improved, sometimes significantly so. In particular, the improved performance is achievable using a random-coding ensemble that is universal, not only in terms of the source sequence, but also in terms of the distortion measure.

In this work, the optoelectronic characteristics of kesterites of the Cu₂NiXS₄ system (X = Si, Ge, Sn) were studied. The electronic properties of the Cu₂NiXS₄ (X = Si, Ge, Sn) system were studied using first-principles calculations within the framework of density functional theory. For calculations, ab initio codes VASP and Wien2k were used. The high-precision modified Beke-Jones (mBJ) functional and the hybrid HSE06 functional were used to estimate the bandgap, electronic and optical properties. Calculations have shown that when replacing Si with Ge and Sn, the band gap decreases from 2.58 eV to 1.33 eV. Replacing Si with Ge and Sn reduces the overall density of electronic states. In addition, new deep (shallow) states are formed in the band gap of these crystals, which is confirmed by the behavior of their optical properties. The obtained band gap values are compared with existing experimental measurements, demonstrating good agreement between HSE06 calculations and experimental data. The nature of changes in the dielectric constant, absorption capacity and optical conductivity of these systems depending on the photon energy has also been studied. The statistical dielectric constant and refractive index of these materials were found. The results will help increase the amount of information about the properties of the materials under study and will allow the use of these compounds in a wider range of optoelectronic devices, in particular, in solar cells and other devices that use solar radiation to generate electric current.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

"Chemical absorption is currently the most advanced technique for capturing carbon dioxide after combustion. A fascinating approach within amine-based technology for post-combustion carbon removal is the utilization of aqueous ammonia as a solvent, leading to a method called chilled ammonia capture. This study aims to enhance the performance of chilled ammonia capture through a thermodynamic assessment, focusing on crystalline configuration.""This study explores the development of an improved second generation chilled ammonia capture process, which involves the formation of solids to enhance capturing efficiency. The simulation software ASPEN is employed to model the expanded UNIQUAC Thermodynamics hypothesis. The modeling encompasses both the conventional carbon ammonia capture process and the more advanced carbon ammonia capture system powered by a crystallizerIn this study, the energy costs associated with implementing different technologies for carbon ammonia capture in typical ultra supercritical power plants are evaluated. The introduction of solid formation in the carbon ammonia capture system has yielded promising results. The findings indicate that the energy required for the carbon ammonia capture system, which utilizes a crystallizer, is approximately 10% lower compared to the overall cost associated with the conventional carbon ammonia capture system. These results highlight the potential for significant energy savings and improved efficiency in carbon capture processes

This paper is the continuation of a previous study, which highlighted some inconsistencies in the RILEM guidelines for the interpretation of the diagonal compression test. Although improved compared to the ASTM guidelines, in fact, the RILEM guidelines underestimate the state of hydrostatic stress induced by the diagonal compression test at the center of the wallette. The new interpretation of the diagonal compression test proposed in this article shows that the RILEM guidelines actually underestimate both the hydrostatic and the deviatoric stress states at the center of the wallette. The new formulation complies with the linear elastic theory and allows us to use the the diagonal compression test to identify the three elastic coefficients of masonry. In particular, it allows the identification of the Poisson ratio, which instead takes on a conventional value in the RILEM and ASTM guidelines. The difference of one order of magnitude between the conventional and proposed Poisson’s ratio is in agreement with the experimental results on another brittle material, namely concrete. Finally, the new proposal fills the gap between the results provided by the two tests usually performed to identify the shear behavior of masonry: the diagonal compression test and the shear-compression test.

The poor solvent crystallization of carbapenem CS-023 has been performed at 25 °C. The following results have been obtained: 1) A solvate crystal Form A (5/2 Ethanol·1/2 H2O) is recovered from 80 v/v% ethanol solution, 2) Form A transforms to Form H (4H2O) by the solid-phase transition through the solvate-free polymorph, Form A-2, and Form A also transformed to Form C (1Ethanol·3H2O) by the solvent-mediated transformation. In the present study, we found that Form C also transforms to Form H by the solid-phase transition through the solvate-free polymorph, Form C-2. The three polymorphs, Form A, H, and C, were composed of the helical-chain structures, respectively. However, there was an incomprehensible affair in the solid phase transition among the three polymorphs. Namely, Form A comprised a left-handed helix.On the other hand, Form C and Form H’s helix chains were in a left- and right-handed helix complex. The solid-phase transition of Form A into Form H suggested the switch of helicity in the solid. We attempted to explain the helicity change in the solid phase transition. As a result, it was suggested that the over-absorption of water of Form A-2 at high humidity plays a vital role in the helicity change.

The present study focuses on the development and optimization of a highly efficient unique hybrid technique — membrane-assisted gas absorption (MAGA) in designing the separation unit, which provides the improvement in mass-transfer of a target component during the natural gas processing in terms of sweetening stage. A novel design of membrane-assisted gas absorption cell is used to enhance the ratio between absorbent amount and membrane surface available for permeation. The performance tests were implemented on example of two gas mixtures separation: one is model ternary gas mixture and the second is quasi real natural gas, which includes number of hydrocarbons, nitrogen, acid impurities and xenon. For both cases, the MAGA unit demonstrated high acid gases removal efficiency, and high recovery of hydrocarbons. The ultimate efficiency of studied system was up to 96 and 61 % of removed acid gases with hydrocarbons losses up to 1 % at highest productivity. In this way, the residual sum of acid gases content may be lowered to 1 vol.% using the heat-free hybrid membrane-assisted gas absorption unit maintaining suitable recovery rate of methane, ethane, propane and n-butane. Nevertheless, the overall efficiency of the process may be enhanced using the specific absorption agents with aqueous amino alcohol solutions.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

Due to its insensitivity to corrosion, textile CFRP (carbon fibre reinforced polymer) reinforcement enables the construction of thin-walled concrete structures such as shells, vaults and girder webs with minimal concrete cover. In contrast to tensile and flexural behaviour, strutting and compressive membrane action of cracked thin-walled carbon reinforced concrete (CRC) elements and the interaction of compressive stresses with transverse tensile loading have not yet been investigated. While for steel reinforced concrete components, extensive biaxial testing has shown a significant reduction of concrete compressive strength as a function of the lateral tensile stress (compression softening), the effect of biaxial loading on CRC structures has not been quantified yet. However, a different behaviour is expected due to different bond properties of steel and CFRP in concrete, smaller crack spacings and the tendency of the CFRP reinforced concrete for in-plane splitting. This paper presents an extensive experimental campaign for investigation of the influence of transverse tension and cracking on the compressive strength of CRC with refined measurement techniques. Based on a literature review on compressive softening behaviour and conventional test setups for steel reinforced concrete, a novel test setup was developed. The phenomenology of compression softening in CRC as well as the main factors influencing compressive membrane behaviour are highlighted. Based on the experimental findings a constitutive law for compression softening behaviour of CRC is proposed.

Audio classification using deep learning models, essential for applications like voice assistants and music analysis, faces challenges when deployed on edge devices due to their limited computational resources and memory. Achieving a balance between performance, efficiency, and accuracy is a significant obstacle in optimizing these models for such constrained environments. In this investigation, we evaluate diverse deep learning architectures, including Convolutional Neural Networks (CNN) and Long Short-Term Memory (LSTM), for audio classification tasks on the ESC 50, UrbanSound8k, and Audio Set datasets. Our empirical findings indicate that Mel Spectrograms outperform raw audio data, attributing this enhancement to their synergistic alignment with advanced image classification algorithms and their congruence with human auditory perception. To address the constraints of model size, we apply model compression techniques, notably magnitude pruning, Taylor Pruning, and 8-bit quantization. The research demonstrates that a hybrid pruned model achieves a commendable accuracy rate of 89 percent, which, although marginally lower than the 92 percent accuracy of the uncompressed CNN, strikingly illustrates an equilibrium between efficiency and performance. Subsequently, we deploy the optimized model on Raspberry Pi 4 and NVIDIA Jetson Nano platforms for audio classification tasks. These findings highlight the significant potential of model compression strategies in enabling effective deep learning applications on resource-limited devices, with minimal compromise on accuracy.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

Polymer-based (nano)composite foams, especially those having a microcellular structure, containing suitable conductive (nano)fillers, have been shown to act as good shielding materials, hence coming as promising to act as shields in electronic devices, limiting/avoiding electromagnetic interference (EMI) pollution. Nevertheless, due to their high (micro)structural complexity, related to their multiphase nature, there is still a lot of unawareness behind the shielding mechanisms acting in these materials, coming as a necessity to study their microstructure-cellular/porous structure-properties relations, especially in terms of their electrical conductivity and EMI shielding efficiency (EMI SE). To target and control the electrical conductivity through a controlled distribution/dispersion of conductive nanofillers, single or combined (nanohybrids), as there is a direct relation between electrical conductivity and EMI SE, as well as the main EMI shielding mechanisms working on the developed microcellular structure of the foams, which are expected to be absorption-dominated or absorption/multiple reflection-based, are two of the main objectives when combining polymer foaming with the addition of conductive nanofillers. The present review work considers the recent developments and trends on polymer-based foams containing conductive nanofillers, especially carbon-based such as carbon nanotubes or graphene-based materials, as well as similar porous structures created using trending technologies such as 3D printing, for EMI shielding applications. It is divided in different sections, starting with the strategy of microcellular foaming to develop polymer-based foams with enhanced EMI shielding characteristics, especially focusing on technologies and methods using supercritical CO2 (sCO2); continuing with the use of polymer foams as templates to synthesize carbon foams with improved EMI shielding performance for high use temperature applications; the recent strategy of combining different functional (nano)fillers to create hybrid nanofillers/nanohybrids to be used at lower amounts as conductive fillers in polymer foams; the control and selective distribution of the nanofillers in terms of favoring the formation of a more effective conductive network and hence promote the enhancement of the EMI SE; the very recent use of computational approaches to tailor the EMI shielding properties of composite foams; and the very trending possibility of creating cellular components with varied porous structures from these materials using 3D printing; to finish, some future perspectives are discussed.

Nonlinear compression of narrow-band (Δ ≈ 0.2 cm-1) 20 ns KrF laser pulses in SF6 at 10 atm and CH4 at 50 atm pressure was studied. Both SBS and SRS optically phase conjugated backward reflected radiation was registered with energy reflectivity 10−14% in SF6 and CH4. In SF6 SBS pulses gradually shortened from 10 ns to 2−3 ns with pumping decrease to the SBS threshold ~ 10 mJ, while the SRS pulse had the shortest length of 30−60 ps for the maximal pumping of 120 mJ and broadened near the SRS threshold of ~30 mJ. For the SRS pulse energy ~ 2 mJ peak power 5×107 W was tenfold higher than the pump power. The theoretical model predicted a soliton-like SRS pulse compression to a temporal length of the order of vibrational relaxation time. There was no pulse compression of backward SBS and SRS radiation in CH4, while in the forward direction SRS pulses shortened to 3−4 ns at reduced pumping.

Among all the active confinement techniques, the use of pre-tensioned stainless steel straps has recently gained much attention. The flexibility of the stainless steel straps allows us to bend and pass them through the thickness of the masonry, thus creating a three-dimensional strengthening system between the two opposite facings. The use of the same perforation for the passage of several straps closed in a loop generates a continuous strengthening system that prevents parts of the structure from falling and injuring the occupants during seismic events. However, the perforations can nullify the in-plane strengthening, as they act as cylindrical hinges and make the reinforcement system labile for certain strap arrangements. Diagonal compression tests on square masonry panels performed in the present study show that the straps improve neither strength nor ductility when running along the mortar head and bed joints, arranged in square meshes. Conversely, they improve both strength and ductility when the straps make angles of 45° with the mortar joints. Furthermore, the experimental results show that the straps exert an anisotropic effect that decreases the apparent in-plane Poisson ratio. They also provide new insights into the diagonal compression test and allow formulating a new proposal for the pseudo-ductility factor.

Background and objectives Osteoporotic vertebral compression fractures, particularly prevalent among the aging population, constitute a pressing global healthcare challenge. They often are unnoticed until severe pain and disability manifest, making them an underdiagnosed and undertreated condition. Patients who suffer from these fractures not only endure excruciating pain but also face diminished quality of life, impaired mobility, and the risk of respiratory compromise due to altered spinal alignment. The economic repercussions of vertebral compression fractures are substantial. Hospitalization costs, rehabilitation expenses, long-term care, and indirect costs related to lost productivity significantly burden healthcare systems and society at large , offering a promising avenue for enhancing patient outcomes and relieving the healthcare and societal financial strain posed by vertebral compression fractures. Kyphoplasty, a minimally invasive surgical technique, offers rapid pain relief, vertebral height restoration and improved function. Recognizing the importance of early intervention, this manuscript highlights the potential of kyphoplasty in mitigating both clinical and economic consequences. By addressing these fractures more effectively, kyphoplasty may potentially reduce long-term healthcare expenses and indirect costs. Material and Methods 66 randomized patients were divided into 2 treatment groups (kyphoplasty using single balloon and double balloon), analyzing radiographic and clinical parameters during 12 months of follow-up. Results Patients treated with double balloon obtained greater anterior and posterior vertebral height after reduction and a better local vertebral angle. Both groups of patients obtained clinical improvement after treatment (VAS and ODI), with no differences between the groups. Conclusion Patients treated with double balloon kyphoplasty had better radiographic results. This revision manuscript delves into the critical dimensions of these fractures, encompassing demographics, clinical consequences, challenges in diagnosis and management, and their profound economic impact. This manuscript serves to introduce an improved kyphoplasty technique to guide to the multifaceted nature of osteoporotic vertebral compression fractures and their management.

Abstract: We present the Hellenic orogenic belt`s main geological structure and architecture of deformation, trying to reach a better interpretation of its geotectonic evolution during the Alpine orogeny. We based on our recent studies and experience about the deformational history of the Hellenides but also on the more modern views, published by other colleagues, concerning the Alpine geotectonic reconstruction of the Hellenides. The structural evolution started during the Permo-Triassic with the continental breaking of the Pangea super-continent and the birth of the Neotethyan ocean realm. Bimodal magmatism and A-type granitoid intrusions accompanied the initial stages of the continental rifting, followed by Triassic-Jurassic multiphase shallow- and deep-water sediment deposition on both formed continental margins. These margins were the Apulian margin, containing the Pelagonia, at the western part of the Neotethyan ocean and the European margin, containing continental parts of the Serbo-Macedonian and Rhodope massifs (upper Vertiskos-Kimi and middle Sidironero-Kerdylia units), at the eastern part of the Neotethyan ocean. Deformation and metamorphism are recorded in six main deformational stages from the Early-Middle Jurassic to the present day, getting started with an Early-Middle Jurassic Neotethyan intra-oceanic subduction and ensimatic island arc magmatism. Compression, nappe stacking, calc-alkaline magmatism and high-pressure metamorphic events related to subduction processes alternated successively through time with extension, orogenic collapse, medium- to high-temperature metamorphism, adakitic and calc-alkaline magmatism and partly migmatization, related to uplift and exhumation of deep crustal levels as tectonic windows or metamorphic core complexes. An S- to SW-ward migration of the dynamic peer compression vs. extension is recognized during the Tertiary Alpine orogenic stages in the Hellenides. In any case extension and crustal uplift follow compression and nappe stacking or compression and exten-sion act simultaneously at different parts of the orogen. We suggest that all ophiolite belts in the Hellenides originated from a single source and this was the Neotethyan Meliata/Maliac-Axios/Vardar ocean basin, parts of which obducted during the Mid-Late Jurassic on both continental margins, Apulian`s (containing Pelagonia) and European`s (containing units of Serbo-Macedonian/Rhodope nappes stack), W-SW-ward and E-NE-ward, respectively. In this case, the ophiolite nappes should be considered as far-traveled nappes on the Hellenides continental parts associated with the deposition of Middle-Late Jurassic ophiolitic mélanges in basins at the front of the adjacent ophiolite thrust sheets. The upper limit of the ophiolite emplacement is the Mid-Upper Jurassic, Callovian-Oxfordian, as shown by the deposition of the Kimmeridgian-Tithonian Upper Jurassic sedimentary carbonate series on the top of the obducted ophiolite nappes. The suture zone between the Pelagonian nappe and the External Hellenides as part of the Apulia plate has been dated about coeval in time with the Paleocene-Eocene to Oligocene SW-ward over thrusting (between 56 Ma and 32 Ma), along the Nestos thrust zone, of the Serbo-Macedonian/Rhodope Sidironero-Kerdylia unit on the tectonically lower-most Rhodope Pangaion unit. In this sense, the Nestos shear zone in the Rhodope province continues until the suturing between Pelagonian and External Hellenides and is the same with this. Therefore, the lower-most Rhodope Pangaion unit could be regarded, as the continuation of the marginal part of the Apulian plate (External Hellenides) that was underthrusted during the Paleocene-Eocene below the unified Sidironero-kerdylia unit and the Pelagonian nappe, following the Paleo-cene-Eocene subduction and closure of a small ocean basin at the western of the Pelagonian (Pindos-Cyclades ocean basin). Was preceded by the Late Cretaceous subduction of the Axios/Vardar ocean remnants below the European continental margin and the final closure of the Axios/Vardar ocean during the Paleocene-Eocene, which were associated with the overthrusting of the European origins Vertiskos-Kimi nappe on the Sidironero-Kerdylia nappe and subsequently the final collision of the European margin and Pelagonian fragment. In this scenario should be assumed, that the true Vardar/Axios suture zone should originate in the deep further to the East between the Rhodope units in the northern Rhodope province, while the Axios/Vardar zone in its today outcrops position should be considered as allochthonous. Subsequently, during synorogenic Oligocene-Miocene extension, the lower-most Rhodope Pangaion unit exhumed as a metamorphic core complex below the Serbo-Macedonian/Rhodope nappes, which were successively exhumed, from the higher to the middle, during Paleocene-Eocene and Eocene-Oligocene extension, respectively. A retreating subduction zone associated with rollback of the subducted lithosphere under the Pelagonian and the other Internal Hellenides nappes stack and/or slap break off and mantel delamination could well explain the Tertiary synorogenic extensional tectonics in the Internal Hellenides, taking place simultaneously with compression in the External Hellenides and the Hellenic foreland or accretionary wedge.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

SARS-CoV-2 attachment and entry inside mammalian cells is mainly mediated by human angiotensin-converting enzyme 2 (ACE2) and its interaction with spike protein. However, it is well known that spike protein also interacts with other molecules like glycosaminoglycans (GAG), e.g., heparan sulfate (HS) or Enoxaparin (EX), which are linear, anionically charged polysaccharides known for their biological activities. The mode of action of these two polysaccharides is to bind spike protein to block the interaction with ACE2 receptors. This study aimed to assess a model capable of confirming the activity of these GAGs in both the wild-type strain of SARS-CoV-2 and its variants, such as the highly variable BA.2.86. This was achieved by combining in silico modeling with in vitro determination using BacMam technology. The results showed the antiviral activity of HS and EX both in vitro and through the in-silico analysis, reconciling conflicting findings from recent studies on the cellular entry of SARS-CoV-2. In conclusion, it is possible to highlight the ability of these molecules to circumvent the high variability of SARS-CoV-2, providing valuable insights into intervention strategies targeting cell entry mechanisms and establishing a safe in vitro model.

In road construction, before applying an asphalt or concrete surface, the ground must be compacted and stabilized. There are two basic methods of soil stabilization: in situ and in a stationary node (ex-situ). The method of performing stabilization in place (in-situ) is the most frequently used method due to its convenience and lower price. The most popular type of binder for stabilization is a hydraulic binder (most often cement and various ashes). Such stabilization is performed at a depth of 10-50 cm, achieving the desired load-bearing parameters. In order to improve them, various chemical additives for stabilization are often used, such as ion exchange compounds, additives based on sulfuric acid, additives based on vinyl polymers or even organic additives using lignosulfonates. However, the use of such additives is associated with much greater costs and environmental burden, resulting in seeking for cheaper and equally effective alternatives. The win-win situation would be for instance recycling the problematic waste-based materials that on one hand are landfilled or impossible to recycle and on the other hand cause problems for the waste producers. Therefore, an interesting issue is the production of stabilization additives from various types of waste materials. As a result of the extensive testing of various waste-based materials blends with soil, the mechanical (compressive strength after 7 and 28 days) and hydraulic (capillary rise, water absorption, frost resistance) soil properties were measured. The optimization process led to obtaining additives compositions ensuring the best strengthening and sealing properties. These were for sandy soil: Pure foil (wax emulsion), Pure foil (wax emulsion) + waste sulphuric acid, RDF from waste tires (wax emulsion), Pure foil (wax emulsion) + “by-pass” waste ash + NaOHx2 and for clayey soil: Pure foil (wax emulsion) + NaOH, Pure foil (wax emulsion) + waste sulphuric acid, Tequant, Pure foil (wax emulsion).

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

Recent technological advances have significantly increased the data volume obtained from deep space exploration missions, making the downlink rate a primary limiting factor. Particularly, JAXA’s Martian Moons eXploration (MMX) mission encounters this problem when identifying safe and scientifically valuable landing sites on Phobos using high-resolution images. A strategic approach in which we effectively reduce image data volumes without compromising essential scientific information is thus required. In this work, we investigate the influence of image data compression, especially as it concerns the accuracy of generating the local Digital Terrain Models (DTMs) that will be used to determine MMX’s landing sites. We obtain simulated images of Phobos that are compressed using the CCSDS-120 with integer/float-point discrete wavelet transform (DWT), candidate algorithms for the MMX mission. Accordingly, we show that, if the compression ratio is 70% or lower, the effect of image compression remains constrained, and local DTMs can be generated within altitude errors of 40 cm on the surface of Phobos, which is ideal for selecting safe landing spots. We conclude that the compression ratio can be increased as high as 70%, and such compression enables us to facilitate critical phases in the MMX mission even with the limited downlink rate.

The aim of the paper is to analyze the experimental results of the influence of elevated temperatures and strain rate on the mechanical and structural properties of steel 42CrMo4. The experiments were based on uniaxial tension and compression tests at high temperatures between 700 °C and 1000 °C and strain rates range 0.0018 - 0.1 s^-1. The influence of temperature and strain rate on yield stress, strain to fracture, hardness, structural changes, and fracture characteristics were analyzed. Due to the dynamic recrystallization phenomenon present during the hot tensile tests, an increase in the flow stress is observed at the beginning of the deformation, after which it decreases until the fracture. By increasing the deformation temperature from 700 °C to 1000 °C, the tensile stress decreases significantly for all strain rates. The increase in the strain rate leads to the increase in the tensile stress. In compression tests by increasing the strain rate, the true strain is slightly increasing, but this depends on the temperature. The non-uniformity of deformations obtained at different values of the strain rate and temperature were also analyzed. Analysis by scanning electron microscopy showed the ductile behavior of the material. The degree of damage of the material caused by the presence of cavities increases by increasing the deformation temperature. For all the presented deformation conditions, the presence of the fracture through the ductile fracture mechanism was produced by the localized of necking and the coalescence of microvoids. By increasing the deformation temperature and reducing the strain rate, the fracture behavior of 42CrMo4 steel can be improved.

Entrapment neuropathies of the lower limb are a misunderstood and underdiagnosed group of disorders, characterized by pain and dysesthesia, muscular weakness, and specific provoking movements on physical examination. The most frequent of these syndromes encountered in clinical practice are fibular nerve entrapment, proximal tibial neuropathy, sural nerve neuropathy, deep gluteal syndrome or sciatic nerve entrapment and lateral femoral cutaneous nerve entrapment, also known as meralgia paresthetica. They are commonly mistaken for lumbar plexopathies, radiculopathies, and musculotendinous diseases, which appear even more frequently and have overlapping clinical presentations. A comprehensive anamnesis, physical examination, and electrodiagnostic studies should help clarify the diagnosis. If the diagnosis is still unclear or a secondary cause of entrapment is suspected, magnetic resonance neurography, MRI or ultrasonography should be conducted to clarify the etiology, rule out other diseases and confirm the diagnosis. Moreover, clinicians should gain familiarity with this disease and their diagnostic confidence should increase, leading to early diagnosis of nerve damage and prevention of muscle atrophy. The reviewed and updated epidemiology, anatomy, pathophysiology, etiology, clinical presentation and EDX technique and interpretation of the entrapment neuropathies of the lower limb are further described in this article.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

We discuss a remote sensing system that is used to simultaneously detect range-resolved differential absorption LIDAR (light detection and ranging; DIAL) signals and integrated path DIAL signals (IP-DIAL) from aerosol targets for ranges up to 22 km. The DIAL/IP-DIAL frequency converter consists of an OPO pumped at 1064 nm to produce light at 1.6 μm and operates at 100 Hz pulse repetition frequency. The probe light is free space coupled to a movable platform that contains one transmitter and two receiver telescopes. Hybrid photon counting/current systems increase the dynamic range for detection by two orders of magnitude. Range resolved and column integrated dry-air CO2 and CH4 mixing ratios are obtained from line shape fits of CO2 and CH4 centered at 1602.2 nm and 1645.5 nm, respectively and measured at 10 different frequencies over ≈ 1.5 cm-1 bandwidth. The signal-to-noise ratios (SNR) of the IP-DIAL returns from cloud aerosols approach 1000:1 and the uncertainties in the mixing ratios weighted according to the integrated counts over the cloud segments range from 0.1 % to 1 %. The range averaged DIAL mixing ratios are in good agreement with the IP-DIAL mixing ratios at the 1 % to 2 % level for both CO2 and CH4. These results can serve as a validation method for future active and passive satellite observational systems.

Consciousness results from comprehending the living creature from its existence in time and space. Thought and consciousness are distinguishing factors between humans and machines having artificial intelligence. No algorithm has been offered for artificial self-awareness based on Thinking. Previous studies have not studied the relationship between consciousness, thinking and time. In this study, the relationship between consciousness, thinking, memories and speech over time has been studied. A deep logical connection exists between consciousness, thinking, and time. An algorithm can be designed for artificial consciousness based on this research findings.

The massive use of electronic equipment has raised concerns about electromagnetic (EM) pollution, leading to increased attention to EM shielding in both civil and military applications. EM absorption materials play a crucial role in reducing the energy of microwaves projected onto their surface. In this work, we propose a novel OTA (over-the-air) antenna test method to evaluate and analyze the functionality of EM absorption materials. This method offers a new and practical way to assess the effectiveness of these materials. Measured results indicate that the presence of the EM absorption material led to a decrease in antenna gain of approximately 2-3 dB, a reduction in efficiency of more than 10-15%, and a smaller radiation pattern during the actual testing process. These findings highlight the impact of EM absorption materials on antenna performance. Compared to the traditional S-parameter testing method, the gain comparison testing method exhibits the advantages of higher accuracy and simpler operation in the lower frequency experiment.

In this research, a design method for the graded triply periodic minimal surface (TPMS) structures with lightweight, high-strength, and high sound absorption properties is proposed. The graded TPMS structures are controlled by linear, quadratic, and sine functions. Uniform TPMS and graded TPMS were manufactured by laser powder bed fusion (LPBF) with AlSi7Mg powder, and an acoustic impedance tube test, compression test, and digital image correlation (DIC) test were ap-plied to obtain the sound absorption and compression properties. The sound absorption coefficient of a uniform Gyroid increases as the number of layers and surface thickness increase, and it in-creases as element size decreases. The sound absorption peak shifts to low frequencies as the number of layers increases. The sound absorption property of Type-Ⅰ graded TPMS is superior to the Type-Ⅱ, and the G-LinearⅠ has the highest sound absorption properties among the three functions. It reveals that the graded TPMS has superior sound absorption performance at low and medium frequencies. The compression and DIC results of graded TPMS also show excellent mechanical properties and energy absorption characteristics.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

One of the uses of Helmholtz resonators is as sound absorbers for room acoustic applications, especially for the low frequency range. Their efficiency is centered around their resonance frequency which is mainly depended on elements of their geometry such as the resonator volume and neck dimensions. Incorporating additional necks on the body of a Helmholtz resonator (depending on whether they are open or closed) has been found to alter the resulted resonance frequency. For this study, tunable Helmholtz resonators to multiple resonance frequencies, are proposed and investigated utilizing additional necks. The resonance frequencies of various multi-neck Helmholtz resonators are first modeled with the use of finite element method (FEM), then calculated with the use of an analytical approach and the results of the two approaches are finally compared. Results of this study show that Helmholtz resonators with multiple resonances at desired frequencies are achievable with the use of additional necks, while FEM and analytical methods can be used for the estimation of the resonance frequencies. Analytical and FEM approach results show a good agreement in cases of small number of additional necks, while the increasing differences in cases of higher neck additions, were attributed to the change in effective length of the necks as demonstrated by FEM. The proposed approach can be useful for tunable sound absorbers for room acoustics applications according to the needs of a space. Also, this approach can be applied in cases of additional tunable air resonances of acoustic instruments (e.g. string instruments).

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

Abstract: The two-dimensional Fuzzy Transform was applied in image compression. The quality of the image compressed with this methodis better than that obtained using methods based on fuzzy relation equations and comparable with that of the JPEG method, with better compression execution times. In this paper we propose a variation of the method based on the two-dimensional Fuzzy Transform of image compression, in which the image is first partitioned into blocks and then each block is compressed with the higher compression rate. The advantage of this method consistsinto a greater compression of the image, guaranteeing a high quality of the reconstructed image.The results show that our method is better than the Fuzzy Transform method improving also the quality of the reconstructed image.

The quasi-beta processing was considered as a promising processing technology to obtain a component with an excellent mechanical properties. To achieve an optimized quasi-beta processing parameter of TC21 alloy, the hot deformation behavior in near β phase region for the alloy with a forged structure was investigated by the thermal compression test and finite element (FEM) simulation. The obtained results indicated that the flow behavior of the samples was significantly influenced by the hot deformation parameters and it exhibited a flow hardening behavior at the start stage of deformation. Based on the experimental data, the constitutive equation and processing maps were obtained. The optimum hot processing parameters was 986℃/10^-3s^-1. Based on the FEM simulation results, the evolution of temperature field, strain field and stress field in the deformed samples at different strains exhibited a similar trend in the unstable region, which distributed symmetrically along the center line of the samples, and the center area of the samples was the highest and the center area of the section was the lowest.

Carbon dots are carbon based nanoparticles, which have the characteristics of simple preparation process, photoluminescence, biocompatibility, adjustable surface function, water solubility, and low toxicity. They are widely used in biological applications such as imaging, biosensing, photocatalysis, and molecular transfer. It has also aroused great interest among researchers in agriculture and has made significant progress in improving crop growth and production. This review presents the physiological functions of carbon dots for crop growth and development, photosynthesis, water and nutrient absorption, and abiotic stress resistance and their applications in improving ecological environment and agriculture as biosensors, and the future application prospects and research directions of carbon dots in agriculture were prospected.

This paper presents a comprehensive evaluation of metal foam employment within polymer electrolyte fuel cells (PEFCs) and compares it with conventional serpentine channels from both experiment viewpoints and computational fluid dynamics simulation. The experiments are designed to study the effects of material, area density, compression ratio, and final thickness of metal foam. Additionally, the influence of housing plate material and relative humidity (RH) is also tested for the first time. The results reveal that at RH=75-100%, the best distributor design is nickel foam with a compression ratio of 70%, a final thickness of 0.5mm, and SS-304 housing plate, which delivers 3110 mA cm^-2 as limiting current density that is scarce in the literature. The PEFC with this foam distributor shows a 10% improvement in maximum power density and 45% in limiting current density compared to the serpentine channel case. While at RH=30%, the same foam flow field with a final thickness of 1mm is a superior option. The experiments also indicate that maximum power density increases by 23% as the compression ratio rises from 0 to 70%, while reducing final thickness from 1 to 0.5 mm causes a 19% enhancement in cell performance. Simulation results reveal that metal foam is more successful in evenly reactant distribution so that the average oxygen mass fraction at the cathode catalyst layer is increased by 38% in the metal foam case compared to the serpentine channel.

The study focuses on the crucial aspect of lossless compression for FAST pulsar search data. The deep generative model PixelCNN, stacking multiple masked convolutional layers, achieves neural network autoregressive modeling, making it one of the most excellent image density estimators. However, the local nature of convolutional networks causes PixelCNN to concentrate only on nearby information, neglecting important information at greater distances. Although deepening the network can broaden the receptive field, excessive depth can compromise model stability, leading to issues like gradient degradation. To address these challenges, the study combines causal attention modules with residual connections, proposing the Causal Residual Attention Module to enhance the PixelCNN model. This innovation not only resolves convergence problems arising from network deepening but also widens the receptive field. It effectively utilizes global features, particularly capturing vertically correlated features prominently present in subgraphs of candidates. This significantly enhances its capability to model pulsar data.In the experiments, the model is trained and validated using the HTRU1 dataset. The study compares the average negative log-likelihood score with baseline models like GMM, STM, and PixelCNN. The results demonstrate the superior performance of the our model over other models. Finally, the study introduces the practical compression encoding process by combining the proposed model with arithmetic coding.

With an increasing concern for global warming, there have been many attempts to reduce greenhouse gas emissions. About 30 % of total energy has been consumed by buildings and much attention has been paid to reducing building energy consumption. While there are many ways of reducing building energy consumption, accurate energy consumption prediction becomes more significant. As mechanical systems are the most energy-consuming components in the building, the present study developed the energy consumption prediction model for a direct-fired absorption chiller by using the ANN technique for the short term. The ANN model was optimized and validated with the actual data collected through a BAS. For the optimization, the numbers of input variables and neurons, and the data size of training were applied. By changing these parameters, the predictive performance was analyzed. In sum, the outcome of the present study can used to predict the energy consumption of the chiller as well as improve the efficiency of the energy management. The outcome of the present study can be used to develop a more accurate prediction model with a few datasets in that it can improve the efficiency of building energy management.

Axonal degeneration resulting from optic nerve damage can lead to the progressive death of retinal ganglion cells (RGCs), culminating in irreversible vision loss. We contrasted two methods for inducing optic nerve damage: optic nerve compression (ONCo) and optic nerve crush (ONCr). These were assessed for their respective merits in simulating traumatic optic neuropathies and neurodegeneration. We also administered neural progenitor cells (NPCs) into the subtenon space to validate their potential in mitigating optic nerve damage. Our findings indicate that both ONCo and ONCr successfully induced optic nerve damage, as shown by increased ischemia and expression of genes linked to neuronal regeneration. Post NPCs injection, recovery in the expression of neuronal regeneration-related genes was more pronounced in the ONCo model than in the ONCr model, while inflammation-related gene expression saw a better recovery in ONCr. In addition, proteomic analysis of R28 cells in hypoxic conditions identified Vps35 and Syntaxin12 genes. Vps35 preserved mitochondrial function in ONCo, while Syntaxin12 appeared to restrain inflammation via the Wnt/β-catenin signaling pathway in ONCr. NPCs managed to restore damaged RGCs by elevating neuroprotection factors and controlling inflammation through mitochondrial homeostasis and Wnt/β-catenin signaling in hypoxia-injured R28 cells and in both animal models. Our results suggest that ischemic injury and crush injury cause optic nerve damage via different mechanisms, which can be effectively simulated using ONCo and ONCr, respectively. Moreover, cell-based therapies such as NPCs may offer promising avenues for treating various optic neuropathies, including ischemic and crush injuries.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

This study presents a methodology to fabricate Ti6Al4V cylindrical compacts with a highly porous core and dense shell with the purpose to mimic the bone microstructure. Compacts with different core diameters were obtained by conventionally press and sintering. Large pores were created with the aid of pore formers. Sintering kinetics was determined by dilatometry, whereas characterization was performed by X-ray computed tomography. Also, permeability was evaluated on the 3D microstructure and the mechanical strength was evaluated by compression tests. Results indicated that sintering is constraint by the different densification rates of the porous and dense layers. Nonetheless, defectless compacts were obtained due to neck bonding between Ti6Al4V particles. Large pores were located in the designed core with similar pore size distribution. Permeability increased following a power law as a function of the pore volume fraction. Stiffness of bilayer components was driven by the porous core, meanwhile, the strength resulted from the combination of both layers. Bilayer materials obtained showed a permeability and mechanical properties, as well as admissible strain (σy /E) similar to those of human bones.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

Conductive nanocomposites play a significant role in tissue engineering by providing a platform to support cell growth, tissue regeneration, and electrical stimulation. In this present study, a set of electroconductive nanocomposite hydrogels based on gelatin (G), chitosan (CH) and conductive carbon black (CB) was synthesized with the aim to develop novel biomaterials for tissue regeneration application. Incorporation of conductive carbon black (10, 15 and 20 wt %) significantly improved electrical conductivity and enhanced mechanical properties with the increased CB content. We employed an oversimplified unidirectional freezing technique to impart anisotropic morphology with interconnected porous architecture. An investigation into whether any anisotropic morphology affects the mechanical properties of hydrogel was conducted by performing compression and cyclic compression tests in each direction parallel and perpendicular to macroporous channels. Interestingly, nanocomposite with 10 % CB produced both anisotropic morphology and mechanical property, whereas anisotropic pore morphology diminished at higher CB concentration (15 and 20 %) imparting denser texture. Collectively, the nanocomposite hydrogels showed great structural stability as well as good mechanical stability and reversibility. Under repeated compressive cyclic at 50 % deformation, the nanocomposite hydrogels showed preconditioning, characteristic hysteresis, nonlinear elasticity, and toughness. Overall, the collective mechanical behavior resembled the mechanics of soft tissues. Electrical impedance associated to the hydrogels was studied in terms of modulus and phase in dry and wet condition. The electrical properties conducted in wet conditions, which is more physiologically relevant, showed low impedance at high frequencies due to capacitive currents. Overall, impedance of the nanocomposite hydrogels decreased with increased CB concentrations. These gelatin-chitosan–carbon black nanocomposite hydrogels show great promise for use as conducting substrates for the growth of electro-responsive cells in tissue engineering.

The cubic nonlinearity of graphene oxide (GO) monolayer was characterized by open and closed Z-scan using a nano-second laser of 10 Hz repetition rate with a Gaussian spatial beam profile. The reverse saturable absorption or positive nonlinearity from open Z-scan and valley-peak traces or positive nonlinearity from closed Z-scan was displayed. The reverse saturable absorption could be from a two-photon or two-step excitation process due to the larger absorption in the lower visible and upper UV wavelength region compared with the excitation source. The nonlinear absorption and nonlinear refraction coefficient were estimated to be ~ 2.62x10-8 m/W and 3.9x10-15 m2/W, respectively. This study also reveals the effect of nonlinear absorption on nonlinear refraction traces.

Broadband noise reduction over the low-mid frequency range in the building and transportation sectors requires compact lightweight sound absorbers of typical sub-wavelength size. The use of multi-layered closely-spaced (micro-)perforated membranes or panels, if suitably optimized, contribute to these objectives. However, their elasticity or modal behaviors often impede the final acoustical performance of the partition. The objective of this study is to get insights into the vibrational effects induced by elastic limp membranes or panels volumetric modes on the optimized sound absorption properties of acoustic fishnets and functionally-graded partitions (FGP). Cost-efficient global optimization of the partition total frequency-averaged dissipation is achieved from simulated annealing with vibrational effects included through an impedance translation method. Critical coupling analysis reveals how the membranes or panels vibrations redistribute the locations of the Hole-Cavity resonances as well as their cross-coupling with the panels first volumetric mode. It is found that elastic limp micro-perforated membranes broaden the first pass-band of acoustic fishnets while smoothing out the dissipation ripples over the FGP optimiza-tion bandwidth. Moreover, the resonance frequency of the first panels mode sets an upper limit to the broadband optimization of FGPs, up to which high dissipation, low reflection and low trans-mission can be achieved.

Oral ferric citrate hydrate (FCH) is effective for iron deficiency in hemodialysis patients.; however, it remains unclear how iron balance in the body affects iron absorption from the intestinal tract. This prospective, observational study (Riona-Oral Iron Absorption Trial, R-OIAT, UMIN 000031406), conducted at 42 hemodialysis centers in Japan, wherein 268 hemodialysis patients without inflammation were enrolled and treated with a fixed amount of FCH for 6 months. We assessed the predictive value of hepcidin-25 for iron absorption and iron shift between ferritin (FTN) and red blood cells (RBCs) following FCH therapy. Serum iron changes at 2 h (ΔFe2h) after FCH ingestion were evaluated as iron absorption. The primary outcome was the quantitative delineation of iron variables on ΔFe2h and the secondary outcome was the description of the predictors of body iron balance. Generalized estimating equations (GEE) were used to identify the determinants of iron absorption during each phase of FCH treatment. ΔFe2h increased when hepcidin-25 and MCH decreased (-0.155, -0.242 to -0.068, p = 0.001; -2.574, -4.421 to -0.726, p = 0.006, respectively) in GEE. Hepcidin-25 increased when erythropoiesis-stimulating agent (ESA) decreased (-0.002, -0.002 to -0.001, p=0.000). FTN increased when RBC and ESA decreased (-0.466, -0.605 to -0.327, p=0.000; -0.002, -0.004 to -0.000, p=0.05, respectively. Limiting erythropoiesis to maintain hemoglobin levels induces RBC reduction in hemodialysis patients, resulting in increased hepcidin-25 and FTN levels. Hepcidin-25 production may prompt an iron shift from RBC-iron to FTN-iron, inhibiting iron absorption even with continued FCH intake.

Vertical III-V semiconductor nanowires have shown promising absorption of light for solar cell and photodetector applications. The absorption properties can be tuned through the choice of III-V materials and geometry of the nanowires. Here, we review recent progress in the design of the absorption properties of both individual nanowires and nanowire arrays. Future directions for the research field are proposed.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

Agaricus bisporus is well known as a source of polysaccharides that could improve human health. The objective of this study was to explore anti-obesity effect of A. bisporus extract (H2Oslim®) abundant in polysaccharides and its underlying mechanism. Pancreatic lipase inhibitory activity in vitro was determined after treatment with H2Oslim® and chitosan. Treatment with H2Oslim® and chitosan significantly decreased pancreatic lipase activity. Five-week-old male SD rats were randomly divided into three groups for acute feeding with vehicle, H2Oslim® at 80 mg/kg body weight (BW)/day, and H2Oslim® at 160 mg/kg BW/day. H2Oslim® does-dependently increased plasma lipid clearance in an oral lipid tolerance test. Five-week-old male C57BL/6N mice were fed a control diet (CD), a high fat diet (HFD), an HFD with H2Oslim® at 80 mg/kg BW/day, H2Oslim® at 160 mg/kg BW/day, or chitosan at 160 mg/kg BW/day for eight weeks. HFD-fed mice showed significant increases of body weight, fat mass, white adipose tissue, average lipid droplet size, and serum levels of glucose, triglyceride, ALT, and AST compared to those in the CD group. However, H2Oslim® or chitosan administration ameliorated these increases. H2Oslim® or chitosan signifi-cantly reduced dietary efficiency and increased fecal excretion levels of lipid, triglyceride, and total cholesterol. These in vitro and in vivo findings suggest that H2Oslim® might act as an anti-obesity agent by inhibiting pancreatic lipase-mediated lipid absorption, at least in part.

The need to recycle carbon fibre reinforced composite polymers (CFRP) has grown significantly to reduce the environmental impact generated by their production. To meet this need, thermoreversible epoxy matrices have been developed in recent years. This study investigates the performance of an epoxy vitrimer made by introducing a metal catalyst (Zn2+) and its carbon fibre composites focusing on the healing capability of the system. The dynamic crosslinking networks endow vitrimers with interesting rheological behaviour, the capability of the formulated resin (AV-5) has been assessed by creep tests. The analysis showed increased molecular mobility above a topology freezing temperature (Tv). However, the reinforcement phase inhibits the flow capability reducing the flow. The fracture behaviour of CFRP made with the vitrimeric resin has been investigated by Mode I and Mode II tests and compared with the conventional system. The repairability of the vitrimeric CFRP has been investigated by attempting to recover the delaminated samples, which yielded unsatisfactory results. Moreover, the healing efficiency of the modified epoxy composites has been assessed by using the vitrimer as an adhesive layer. The joints were able to recover about 84% of the lap shear strength of the pristine system.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

The primary goal of picture compression is to reduce the amount of unused image data while still storing or transmitting it in a format that is appropriate. The compression of raw binary data is quite different from the compression of a picture, and these differences may be rather substantial. In light of this, compression is often regarded as an essential technique for the purposes of both data storage an d transmission in order to mitigate the excessive amounts of data that are generated by these images. In order to transmit enormous datasets, particularly for the purposes of telemedicine and teleradiology, one needs a significant amount of storage capacity as well as an expansive network. As a result, compression is an important aspect of medical imaging. In addition to the importance of compression, the quality of the photos themselves is also an essential factor in the success of analysis. In addition to this, the amount of time necessary to compress the photographs before sending them should be reduced.

Image compression is a top priority today due to the need for faster encoding and decoding. To achieve this, the present study has proposed the use of Canonical Huffman Coding (CHC) as an entropy coder, which has a lower decoding time complexity than binary Huffman codes. For image compression, combining of the Discrete Wavelet Transform (DWT) and CHC with Principal Component Analysis (PCA) has been recommended. The lossy method has been introduced by using PCA, followed by DWT and CHC to enhance compression efficiency. By using DWT and CHC instead of PCA alone, the reconstructed image has been found to have a better peak signal-to-noise ratio (PSNR) value. This study has developed a hybrid compression model combining the advantages of DWT, CHC and PCA. With the increasing use of image data, better image compression techniques are necessary for efficient use of storage space. The proposed technique has achieved up to 60% compression while maintaining high visual quality. This method has also outperformed the currently available techniques in terms of both PSNR (in dB) and bit-per-pixel (bpp) scores. This approach has been tested on various color images, including Peppers 512×512 and Couple 256×256, showing improvement by 17 dB and 22 dB, respectively, while reducing bpp by 0.56 and 0.10, respectively. For grayscale images, i.e., Lena 512×512 and Boat 256×256, the proposed method has shown an improvement by 5 dB and 8 dB, respectively, with a decrease of 0.02 bpp in both cases.

The study on graphs emerging from different algebraic structures like groups, rings, fields, vector spaces, etc. is a prominent area of research in mathematics, as algebra and graph theory are two mathematical fields that focuses on creating and analysing structures. There are numerous studies linking algebraic structures and graphs, which began with the introduction of Cayley graphs of groups. Several algebraic graphs have been defined on rings, which have huge-growing literature. In this article, we systematically review the literature on some variants of Cayley graphs that are defined on rings, to understand the research in this area.

The volume of vehicular traffic in large cities has increased in recent years, the devices that collect vehicular GPS data such as cameras, GPS receivers and others generate millions of records at every instant of time generating problems in processing and storage of these data which becomes important for researchers. Intelligent Transportation Systems perform vehicle monitoring and control by collecting GPS trajectories, this large volume of information is necessary to have an optimal storage process. Its processing by means of compression techniques and simplification algorithms allow to reduce the necessary storage space. This paper presents a GPS trajectory simplification algorithm that considers noise reduction, point simplification and analysis of road network information. The results obtained on two data sets from the cities of California and Beijing are satisfactory, achieving a higher compression ratio without affecting data quality

The photophysical properties of Cu(II) complexes with 5,10,15,20-meso-tetrakis(phenyl)porphyrin and 5,10,15,20-meso-tetrakis(N-methylpyridium-4-yl)porphyrin were examined by luminescence and femtosecond time-resolved absorbance methods respectively. These studies were supported by DFT and TD-DFT calculations which highlight the important role played by a ligand-to-metal charge-transfer states in directing the system towards either intersystem crossing to the triplet hypersurface or coordinative expansion to a five-coordinate quasi-stable intermediate. The latter processes occurs when the porphyrin is photolyzed in the presence of suitably located Lewis bases. Femtosecond time resolved absorbance measurements on Cu(II)-5,10,15,20-meso-tetrakis(N-methylpyridium-4-yl)porphyrin confirm that the coordinative expansion in water occurs in approximately 700 fs while crossing to the triplet hypersurface takes approximately 140 fs in the same solvent. These processes are mutually exclusive, but both can occur simultaneously depending on the environment of the porphyrin. The ratio of the two processes depends on the relative orientation of the Lewis base with respect to the copper atom at the time of excitation. As a consequence, copper porphyrins such as these, are excellent probes to the environment of the porphyrin, and can be used to identify the location of the porphyrin when interacting with DNA fragments.

Purpose: Metastatic spinal cord compression (MSCC) is a severe complication of cancer that can lead to irreversible neurological impairment, necessitating prompt recognition and intervention. This retrospective, single-center study aimed to determine the prognostic factors and survival rates among patients presenting with MSCC secondary to lung cancer. Methods and Materials: We identified 74 patients with epidural metastases-related spinal cord compression and a history of lung cancer, through the electronic database of Medway Maritime Hospital in United Kingdom (UK), spanning the period from April 2016 to September 2021. Among them, 39 were below 55 years old, while 35 were aged 55 years or older, whereas 24 patients were diagnosed with small cell lung cancer (SCLC), and 50 patients had non-small cell lung cancer (NSCLC). Results: The median overall survival (OS) was 5.5 months, with 52 out of 74 patients dying within 6 months of the diagnosis of MSCC. For the entire cohort, the statistically significant variables on multi-variate analysis were: cancer type (NSCLC had improved OS), number of involved vertebrae (one to two vertebrae involvement had improved OS) and time taken to develop motor deficits (≤10 days to develop motor deficits had worsened OS). For the NSCLC cohort, the statistically significant variables on multivariate analysis were: molecular alterations (patients with epidermal growth factor receptor (EGFR) mutation), pre-treatment ambulatory status, Eastern Cooperative Oncology Group (ECOG) performance status, and time taken to develop motor deficits. Conclusions: Within the entire cohort, patients diagnosed with NSCLC and spinal metastases affecting one to two vertebrae exhibited enhanced OS. Within the NSCLC subgroup, those with EGFR mutations, who were ambulatory, and possessed an ECOG performance status of 1-2, demonstrated improved OS. In both the entire cohort and NSCLC subgroup, the development of motor deficits within a period of ≤10 days was associated with poorer OS.

Photophysical properties of a series of bis(arylydene)cycloalkanone dyes with various donor substituentns are studied by quantum chemistry. Their capacity for luminescence and nonradiative relaxation through trans-cis isomerization is related to their structure, in particular, to the donor capacity of the substituents and the degree of conjugation due to the central cycloalkanone moiety. It is shown that cyclohexanone central moiety introduces distortions and disrupts the conjugation, thus leading to a nonmonotonic change in their properties. The increasing donor capacity of the substituents causes increase in the HOMO energy (raise of the oxidation potential) and decrease in the HOMO-LUMO gap, which results in the red shift of the absorption spectra. The ability of the excited dye to relax through fluorescence or through trans-cis isomerization is governed by the height of the barrier between the Franck–Condon and S1-S0 conical intersection regions on the potential energy surface of the lowest π-π* excited state. This barrier also correlates with the donor capacity of the substituents and the degree of conjugation between the central and donor moieties. The calculated fluorescence and trans-cis isomerization rates are in good agreement with the observed fluorescence quantum yields.

Currently, the design of the concrete mix is an important part of the environmental problem. In front of this question, engineers face a major challenge that is addressed in two ways. On one hand, how do they use its component materials to improve its mechanical properties, on the other hand how do they use less polluting materials? Hence, in an environmental and economical view, laboratory tests were carried out on samples of concrete reinforced with smooth steel fiber extracted from the waste tires, in order to assess its impact and to prove its mechanical feasibility for these purposes. Consequently, laboratory results have shown satisfactory improvement in the behavior of concrete under compression loads in the elastic stage and an increase in ductility and toughness of the matrix in the plastic stage. Besides, taking into account the discontinuity and the structural disturbances observed during the loading of samples in the post-elastic state, a method has been proposed to calculate "the effective toughness and toughness Index of fiber concrete; on the other hand, this method has helped to better optimize length and slenderness of fibers for better use of this recycled material