The radiation-induced optical absorption at 1.5-5.5 eV (up to the beginning of fundamental absorption) has been analyzed in CVD diamond disks exposed to 231-MeV 132Xe ions with four fluences from 1012 to 3.81013 cm-2. The 5-mm diameter samples (thickness 0.4 mm) were prepared by Diamond Materials, Freiburg (Germany), average grain size at growth site was around 80 m, the range of xenon ions was R= 11.5 m. The intensity of several bands grows with ion fluence thus confirming radiation-induced origin of the defects responsible for these bands. The recovery of radiation damage has been investigated via isochronal (stepwise) thermal annealing procedure up to 650°C, while all spectra were measured at room temperature. Based on these spectra, the annealing kinetics of several defects, in particular carbon vacancies (GR1 centers with a broad band 2 eV) and complementary C-interstitial-related defects ( 4 eV), as well as vacancies located nearby nitrogen substitutional atoms (narrow bands around 2.5 eV) have been constructed. The experimental kinetics have also been analyzed in terms of the diffusion-controlled bimolecular reactions. The migration energies of tentatively interstitial atoms (mobile components in recombination process) are obtained, their dependence on the irradiation fluences is discussed.

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed fixed displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. Simulation results demonstrate the four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation.

The partial discharge (PD) event in high voltage insulation releases energy, exerts mechanical pressure, and generates elastic waves. Detecting and locating these PD events through short-duration acoustic pulses is well-established, particularly in gas-insulated systems and oil-insulated transformers. However, its full potential remains untapped in solid insulation systems, where the propagation capability of acoustic pulse and the acoustic reflections pose fundamental challenges to the Acoustic Emission (AE) detection technique. This study investigates the influence of reflections and multiple paths on the propagating acoustic pulse in polymeric insulating materials using a finite element method (FEM) in COMSOL. It was observed that the reflections from the boundary influence the propagating pulse's shape, peak magnitude, and arrival time. An analytical MATLAB model further quantifies the impact of multiple propagation paths on the shape, magnitude, and arrival time of the pulse travelling in a cylinder. Additionally, a Perfect Matched Layer (PML) was implemented in the COMSOL model to eliminate reflections from the boundary, and it revealed that the acoustic pulse magnitude decreases with distance following the inverse square law. In essence, the models aid in measuring how reflections contribute to the observed signals, facilitating the precise identification of the source of the PD event in the tested system.

The release of the active substance from the matrix modified-release tablets based on Kollidon®SR and chitosan depends on its solubility in the dissolution medium and on the composition of the matrix-forming polymers. The study is based on new oral matrix tablets based on Kollidon®SR and chitosan, formulated to optimize the low oral bioavailability of chlorzoxazone, a non-steroidal anti-inflammatory drug, a class II Biopharmaceutical Classification System. Nine types of chlorzoxazone matrix tablets were obtained using the direct compression method, and their combination at 1:1, 1:2, 1:3 chlorzoxazone/ excipients, 20%-40% (w/w) Kollidon®SR, 3-7% (w/w) chitosan and the auxiliary substances were formulated in constant concentrations. Pharmaco-technical characterization included the analysis of flowability and compressibility properties (flow time, friction coefficient, angle of repose, Hausner ratio, Carr Index), and of pharmaco-chemical characteristics (mass and dose uniformity, thickness, diameter, mechanical strength, Friability, degree of softening, in vitro release profile) of the tablets. Based on the initial evaluation of the pharmaco-technical analysis, pharmaco-chemical characteristics, and in vitro release profile, only three matrix tablet formulations (F1b, F2b, and F3b) were further tested. They were evaluated through Fourier-transform infrared spectrometry, X-ray Diffraction, thermogravimetry, differential scanning calorimetry, and in vitro dissolution tests. The three formulations were comparatively studied regarding the release kinetics of active substances using in vitro release testing. The results were analyzed by fitting into four representative mathematical models for the modified release oral formulations. In vitro kinetic study reveals a complex mechanism of release occurring in the first (0 - 2 hours) and second (2.0 hours – 36 hours) steps of drug release. Two factors have been calculated to assess the release profile of chlorzoxazone: f1 - the similarity factor and f2 - the factor difference. The results have shown that both Kollidon®SR and chitosan may be used as matrix-forming agents when combined with chlorzoxazone. In vitro dissolution tests revealed the F2b sample, data suggesting a faster drug release. The three formulations showed optimum pharmaco-technical properties and in vitro kinetic study, and they had tremendous potential to be used in oral pharmaceutical products for the controlled delivery of chlorzoxazone.

This study develops a vitamin C controlled-release system trackable via color changes as a function of vitamin C release. The system is composed of coaxial microfibers prepared via coaxial electrospinning, with a core of poly(ethylene oxide) (PEO) incorporating vitamin C, and a shell composed of polycaprolactone (PCL) containing polydiacetylene (PDA) as the color-changing material. The shell thickness was controlled by adjusting the amount of PCL ejected during electrospinning, allowing the regulation of the release rate of vitamin C. When vitamin C added to PEO penetrated the PCL layer, the color of PDA changed from blue to red, indicating a color change. The results of this study can be applied to devices that require immediate detection of vitamin C release levels.

This article describes an approach for optimising sensor-controlled systems through minimal intervention, utilising Fuzzy Linear Systems of Equations (FLSE). Staring with a generalised model of the system behaviour, incorporating an array of control units, environmental sensors, and an expert knowledge base. The described problems of detecting the level of intervention needed to change the system state to another is handled with the help of developed methods for solving the inverse problem for FLSE. By achieving minimal intervention, we ensure that system adjustments effective, economically optimal and non-intrusive. A MATLAB-based implementation is presented.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

A novel technique suitable for propulsion of small unmanned aerial vehicles (UAV) is discussed in this paper. This approach utilizes the rotational energy of airborne gyro rotors and converts it into translational propulsion for the vehicle. The energy conversion is achieved by generating precisely directed centrifugal force pulses through short-duration rotor unbalances. The accurate control of the timing and magnitude of these unbalances is crucial for successful propulsion generation. Our first-order theory of controlled unbalance propulsion (CUP) predicts the potential for achieving high translational accelerations and vehicle velocities up to orbital levels. Power saving levitation of UAVs can be attained. In this paper, we provide traceable evidence that pulsed centrifugal propulsion is based on well-established laws of physics and can be realized using state-of-the-art technologies.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

The purpose of this study is to investigate the impact of the voltage drop of a three-phase voltage source inverter in driving brushless motors. This study also proposes an enhanced Field Oriented Control scheme that accounts for the inverter voltage drop enabling efficient drive at very low motor-speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme.

Voltage-gated potassium (Kv) channels and hyperpolarization-activated cyclic nucleotide-gated (HCN) channels share similar structures but have opposite gating polarity. Kv channels have a strong coupling ( >109) between the voltage sensor (S4) and the activation gate: when S4s are activated the gate is open to >80%, but when S4s are deactivated, the gate is open < 10-9 of the time. Using noise analysis, we show that the coupling between S4 and the gate is < 200 in HCN channels. In addition, using voltage clamp fluorometry, locking the gate open in a Kv channel drastically altered the energetics of S4 movement. In contrast, locking the gate open or decreasing the coupling between S4 and the gate in HCN channels had only minor effects on the energetics of S4 movement, consistent with a weak coupling between S4 and the gate. We propose that this loose coupling is a prerequisite for the reversed voltage gating in HCN channels.

This paper describes different variants of broadband and simple attenuator modules for beamforming applications, based on Radio Frequency Micro Electro-Mechanical Systems (RF-MEMS), framed within Coplanar Waveguide (CPW) structures. The modules proposed in the first part of this work differ in their actuation voltage, topology, and desired attenuation level. Fabricated samples of basic 1-bit attenuation modules, characterized by a moderate footprint of 690 x 1960 µm2 and aiming at attenuation levels of -2, -3 and -5 dB in the 24.25-27.5 GHz range, are presented in their variants featuring both low actuation voltages (5-7 V) as well as higher values (~ 45V), the latter ones ensuring larger mechanical restoring force (and robustness against stiction). Beyond the fabrication non-idealities that affected the described samples, the substantial agreement between simulations and measurement outcomes proved that the proposed designs could provide precise attenuation levels up to 40 GHz, ranging up to nearly -3 dB and -5 dB for the series and shunt variants, respectively. Moreover, they could be effective building blocks for future wideband and reconfigurable RF-MEMS attenuators. In fact, in the second part of this work, combinations of the discussed cells and other configurations meant for larger attenuation levels will be investigated.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Background: Immersive and non-immersive VR technology has been increasingly employed in training. This has encouraged physicians working in skill development to try using it to improve the learning, emotional recognition, and social skills of various disorders. This study aimed to explore the controlled trials employing VR in autism, ADHD, and dyslexia. Methodology:A literature review has been conducted, on PubMed, Scopus, and Web of Science. Any controlled trial in the pediatric age group, involving the comparison of VR training with other types of therapies in autism, ADHD, and dyslexia was included. Results:Only four controlled trials were identified, comprising a total of 208 patients, with ages ranging from 6-16 years. Out of these studies, two involved patients with autism, one with ADHD, and one with dyslexia. VR was successful in improving emotional recognition but not social interaction in autism. All trials did not mention thoroughly possible complications of prolonged use of VR. Conclusion: Despite being a promising technology, there is still a long road to prove the validity of using VR in skills development. Few controlled trials have been tailored to explore VR advantages over conventional training and therapies, most of them have a limited sample size, a short training course, and no mention of possible setbacks, such as ocular effects and social isolation.

In a context of increasingly necessary energy transition, precise modelling of profiles for low-voltage (LV) network consumers is crucial to enhance hosting capacity. Typically, load curves for these consumers are estimated through measurement campaigns conducted by Distribution System Operators (DSO) for a representative subset of customers or through the aggregation of load curves from household appliances within a residence. With the instrumentation of smart meters becoming more common, a new approach to modelling profiles for residential customers is proposed to make the most of the measurements from these meters. The disaggregation model estimates the load profile of customers on a low-voltage network by disaggregating the load curve measured at the secondary substation level. By utilizing only the maximum power measured by Linky smart meters, along with the load curve of the secondary substation, this model can estimate the daily profile of customers. For 48 secondary substations in our dataset, the model obtained an average symmetric mean average percentage error (SMAPE) error of 4.91% in reconstructing the load curve of the secondary substation from the curves disaggregated by the model. This methodology can allow the estimation of the daily consumption behaviors of the low-voltage customers. In this way, we can safely envision solutions that enhance the grid hosting capacity.

Static voltage stability has become one of the significant risks faced by large-scale renewable energy integration. However, traditional methods for static voltage stability analysis are often overly complex. This paper constructs an equivalent impedance model for renewable energy integrated distribution power systems, proposing a static voltage analysis method for renewable energy integrated distribution power systems based on impedance model index. This method has been verified to be applicable not only to renewable energy single-infeed system but also to multi-infeed system. Furthermore, an analysis is conducted on the influence of the integration capacity, location of renewable energy, and the topology of networks on impedance model index, indicating that a higher impedance model index corresponds to greater static voltage stability margins in the system. Hence, during the planning of renewable energy integration, the plan with the highest impedance model index should be selected. Finally, the accuracy of the analysis methods and conclusions in this paper was validated based on the IEEE 14-node system.

In many developing countries of the world including Pakistan motorcycle steeling is one of the main issue that needs to be dealt with an iron hand as it leads to economic losses as well as crime increase in the society, according to the DOWN REPORT there were 28609 motorcycle stolen in 2019 and this number has been increased to 34908 in 2020. Now due to the increasing motorcycles stealing crime what measures can we take to reduce the number of motorcycle theft the rule of technology is enormous in this regards specially information technology (IT) , information technology can play an important role in the security of motorcycles from being theft by the thieves, Information technology provide us the GSM based control system which can be very help full to construct a security system for motorcycle in order to make it antitheft.

When overhead lines are impacted by lightning, the traveling wave of the fault contains a wealth of fault information. The accurate extraction of feature quantities from transient components and their classification is fundamental to the identification of lightning faults. The extraction process may involve modal aliasing, optimal wavelet base issues, and inconsistencies between the lightning strike distance and the fault point, which have the potential to impact the effectiveness of recognition. This paper presents a method for identifying lightning strike faults by utilizing Kullback-Leibler (KL) divergence enhanced Variational Mode Decomposition (VMD) and Symmetric Geometry Mode Decomposition (SGMD) improved with Permutation Entropy (PE) to address the aforementioned issues. A model of a 220 kV overhead line is constructed using real faults to replicate scenarios of winding strike, counterstrike, and short-circuit. The three-phase voltage is chosen and then sub-jected to Karenbaren decoupling in order to transform it into zero mode, line mode 1, and line mode 2. The zero mode voltage is decomposed using KL-VMD and PE-SGMD methods, and lightning identification criteria are developed based on various transient energy ratios. The research findings demonstrate that the criteria effectively differentiate between winding strike, counterstrike, and short-circuit faults, thus confirming the accuracy and efficacy of the lightning fault identification criteria utilizing KL-VMD and PE-SGMD.

The coupling of AC and DC power will impact the protective actions on the AC side and pose a threat to the stable operation of the interconnection system. Therefore, a new longitudinal protection method is proposed based on the comprehensive distance similarity of voltage waveforms. Initially, the measured voltage and current data are extracted to calculate the reference voltage, and the voltage waveform fitting is optimized. Subsequently, the Euclidean dynamic time warp (DTW) distance and entropy weight method are utilized to process the voltage waveform, enabling the calculation of its comprehensive distance similarity. This similarity is adopted to determine fault location. A hybrid DC multi-feed AC/DC interconnection system, incorporating line commutated converter-voltage source converter (LCC-VSC) and line commutated converter-modular multilevel converter (LCC-MMC), was established in PSCAD, and fault data was simulated and output. The effectiveness of the protection scheme was validated using MATLAB. Simulation results demonstrate that the proposed method can accurately distinguish between faults inside and outside a region. When compared to existing protection methods, it demonstrates superior performance in resisting transition resistance and noise interference, while also mitigating the impact of data asynchronicity. The speed and reliability of the method are further enhanced.

A robust explicit model predictive control (EMPC)-based frequency adaptive grid voltage sensorless control is developed for a grid-connected inverter (GCI) via a linear matrix inequality (LMI) approach under the model parameter uncertainties and non-ideal grid environment. The control scheme is achieved by an enhanced prediction model rather than the conventional prediction model provided by fixed parameters to maintain the quality of grid currents injected into the grid when the model parameters are varied. Furthermore, an LMI-based observer is integrated with the disturbance observer to improve the reference tracking performance and reject disturbances. The proposed observer is employed for the grid frequency adaptive control without need of grid voltage sensors. The proposed current controller and observer employ the LMI scheme to maintain a stable and robust operation of the GCI. The discrete-time frequency response and pole-zero map analyses are used to investigate system stability and robustness against parameter uncertainties. Comprehensive simulation, experimental results and analyses clearly demonstrate the robustness of the proposed control scheme under various adverse test conditions with unexpected grid and system uncertainties.

The agricultural sector faces challenges due to climate change and the growing global population. Alkaline stress could adversely impact plant growth and crop production. This stressor diminishes water quality essential for crop cultivation, consequently impairing plant growth and overall productivity. Gamma-aminobutyric acid (GABA), a non-protein amino acid, may exhibit multifaceted roles in plant responses to adverse environmental conditions. Optimization of crop production in controlled environmental agriculture under artificial light attracted much attention. In the present study, we investigated the effects of different light spectra and GABA concentrations on Lollo Rosso lettuce plants under alkaline stress. Seedlings were placed under different light spectra [red (R), blue (B), white (W), 3R:1B, and 2R:1B:1far-red (FR)] and treated by GABA (0 and 50 µmol). Alkaline conditions were instituted by applying NaHCO3 at a concentration of 40 mM. The experiment incorporated a control treatment without NaHCO3. In general, R light exposure caused the highest growth performance of lettuce plants. GABA augmented biomass production in control and alkaline-treated plants across all light spectra. Additionally, it increased the concentrations of photosynthetic and protective pigments under alkaline conditions. GABA also improved the photosynthetic performance under all light spectra. Non-photochemical quenching and pigmentation were enhanced by exposure to B light, especially in plants treated with GABA. Alkaline stress induced an increase in soluble carbohydrate content in the lettuce leaves. These findings highlight the support of GABA application in facilitating coping plants to alkaline stress.

The design of randomized controlled trials for low-resource settings has unique challenges. One challenge is ensuring recruitment success in the face of a lack of information about prevalence of disease in the population. What disease burden data may exist is old and from distant regions, adding guesswork into site design. This leads to a high chance that the sample size will not be recruited in any reasonable timeframe—a challenge even in high-resource settings. While cross-sectional prevalence studies could be used as a type of feasibility study informing trials by generating near real-time prevalence estimates for the future trial site, such studies take years to complete. This duration makes insertion of such a study in trial design impossible. An empirically supported combination of new approaches that sidesteps unnecessary hurdles is presented, the Pop-Up Prevalence with Private Ethics (PUPPE) design. PUPPE includes using a COVID-validated, more targeted method of data collection, use of accepted ethics review from universities or hospitals to avoid lengthy public ethics review, and—if needed—post-study in silico participant randomization. Only this design would enable clinical trial designers to insert fit-for-purpose prevalence studies within the design phase of their trials, leading to informative outcomes.

A novel low-power MOS-only voltage reference is presented. The Enz-Krummenacher-Vittoz (EKV) model is adopted to provide a new perspective on the operating principle. The normalized charge density, introduced as a new variable, serves as an indicator when trimming the output temperature coefficient. The proposed voltage reference consists of a specific current generator and a 5-bit trimmable load. Thanks to the well-match between the current source stage and the output stage, the non-linear temperature dependence of carrier mobility is automatically canceled out. The circuit is designed in 55 nm COMS technology. The operating temperature ranges from -40 ∘C to 120 ∘C. The average temperature coefficient of the output voltage can be reduced to 21.7 ppm/∘C by trimming. The power consumption is only 23.2 nW with a supply voltage of 0.8 V. The line sensitivity and the power supply rejection ratio at 100 Hz are 0.011 %/V and -89 dB respectively.

Photovoltaic systems and wind energy systems are generally used in distributed system. However, zero-sequence and harmonic currents occur due to photovoltaic systems, and positive-sequence harmonic currents occur due to wind turbines. Thus, the sheath current in high voltage cables increases due to these currents and poor power quality in distributed generation plants. Metal parts of the cable are grounded to prevent the negative effects of sheath currents. When long high voltage cable lines are grounded with the method in the literature, high sheath current and voltage occur on the cable sheath. Therefore, the SSBLR method is designed as a new method for the distributed generation system. The SSBLR method has been optimized with prediction methods and multi-objective optimization methods to prevent negative effects of the sheath current. Pareto optimal method is used as multi-objective optimization method, and artificial neural network, hybrid artificial neural network and regression methods are used as prediction method. The most dominant result is searched using different estimation and optimization methods in pareto optimal method. When the artificial neural network-genetic algorithm hybrid method is used as a prediction method, and genetic algorithm used as optimization method, significant decreases are observed in sheath current and voltage.

Hypertension (HTN) is the foremost contributor to cardiovascular diseases (CVD), which remain a leading cause of death. However, adherence to the properly prescribed dosage form is critical and challenging for patients with chronic diseases such as HTN to prevent illness progression and death. The study’s objective was to develop AMB-loaded subcutaneous implants to reduce the frequency of administration, thus improving patient compliance during HTN management. AMB subcutaneous implants were prepared using continuous hot melt extrusion technology using PCL and PLGA with dimensions of 7.5 cm (length) by 2 mm (diameter). The implants were characterized for thermal characteristics, drug-excipient incompatibilities, surface morphology, fracturability, in vitro release, and stability studies. DSC showed that the drug was in the crystalline state in the fabricated implants. Scanning Electron Microscopy (SEM) revealed a smooth surface. The lead formulation presented good drug content, showed an extended drug release profile over 30 days, and followed zero-order release kinetics with a mean dissolution time of 15 days. The formulation was stable over 30 days in accelerated stability conditions (the last time point was tested, 40℃/75% RH), and the release profile was similar to the initial drug release profile. The lead formulation showed good fracturability during textural analysis. Therefore, the hot melt extruded implants could be an alternative management strategy for conventional amlodipine besylate (AMB) formulation.

Abstract Background: Cluster randomized controlled trials are increasingly becoming popular in public health research interventions and health services research in primary health care design and use in low and middle-income countries. However, the majority of researchers in these trials did not account correctly for the effect of confounders and clustering in the design and analysis stages. Objectives: This article aimed to review the main implications of implementing a cluster randomized controlled trials design in public health research and emphasize the practical application of proper analytical methods and the performance of different statistical models. Methods: The practical application of various analytical methods is validated via the utilization of experimental data from a public health research case study. This article also demonstrated the performance of hierarchical models and made comparisons in terms of empirically precise effect size estimates. Results: Three hierarchical statistical models were provided with highly varied effect sizes during the analysis of the intervention effect on outcome, such as model 1 (AOR: 14.32; 95% CI: 3.75–54.68), model 2 (ARR: 3.52; 95% CI: 2.16–5.77), and model 3 (ARR: 4.79; 95% CI: 2.69–5.52).Conclusion: Inaccurate results and potentially misleading conclusions can arise from improper cluster randomized controlled trial designs and analyses. This article has shown that real-world data can be adjusted for the effects of confounders and clustering, and we advocate for the routine use of suitable design and analytical methods. This article concludes that researchers should be careful when selecting hierarchical models to analyze cluster randomized controlled trials.

Active front-end (AFE) rectifiers have been becoming widely employed in power systems to achieve unity power factor and harmonic mitigations. The typical modeling approaches applied for AFE rectifiers in the literature mostly relied on two baselines named the detailed model and the time average model. The former approach deals with the switching element model (SEM) leads to significant harmonics in currents with distorted waveforms. The latter approach uses the average-value model (AVM) to overcome the currents’ harmonics as well as provide fast responses. However, even the AVM baseline has contained problems during the starting stage (lack of control signals) and over the dead-time periods which causes serious issues in the implementation process. This paper presents an improved dynamic AVM for AFE rectifiers by precisely considering the issues mentioned above along with the practical starting procedure and desirable initialization. The studied AFE rectifier is developed using the voltage-oriented control (VOC) technique based on the different modeling methodologies including SEM, Conventional AVM, and the proposed AVM. The performance of all models is analyzed and compared using simulation results with MATLAB/Simulink R2023a Function blocks for all the algorithm parts and SimScape elements for the electrical circuit model. The simulation results illustrate that the performance of the proposed AVM approach can closely resemble the behavior of the SEM baseline with low harmonic distortion.

Aqueous Zinc ion batteries (ZIBs) possess significant potential in large energy storage systems due to their cost-effectiveness and environmental protection. However, the limited voltage window and poor reaction kinetics of the cathode material are still bottlenecks, restricting the further development of ZIBs. In this work, we rationally design Ni-doped V2O5@3D Ni core/shell composite on carbon cloth electrode (Ni-V2O5@3D Ni@CC) by growing Ni-V2O5 on the free-standing 3D Ni metal nanonets for high-voltage and high-capacity ZIBs. Impressively, the embedded Ni doping increases the interlayer spacing of V2O5, extending the working voltage and improving the Zn2+ kinetics reaction of the cathode materials, at the same time the 3D structure with high specific surface area and superior electronic conductivity benefits to fast Zn2+ transport. Consequently, the as-designed Ni-V2O5@3D Ni@CC cathodes can operate within a wide voltage window from 0.3 to 1.8 V vs. Zn/Zn2+ and deliver a high capacity of 270 mAh g-1 at a high current density of 0.8 A g-1. In addition, the reversible Zn2+ (de)-incorporation reaction mechanisms in the Ni-V2O5@3D Ni@CC cathodes are investigated by multiple characterization methods. As a result, we achieve a big step toward the practical applications of commercial ZIBs.

AbstractIntroduction: Increasing knowledge of obstetric danger signs (ODS) and encouraging birth preparedness and complication readiness (BPCR) practices are strategies to increase skilled maternal health service utilization in low-income countries. One of the methods to increase mothers' knowledge about ODS and promote BPCR practice is through health education intervention (HEI). However, the effect of context-specific community-based health education led by women's groups on these outcomes has not been comprehensively studied, and the existing evidence is inconclusive. Thus, we aimed to evaluate the effect of a context-specific community-based HEI led by women's groups on mothers' knowledge regarding ODS and BPCR practices in southern Ethiopia.Methods: An open-label, two-arm parallel group cluster-randomized controlled trial was conducted from January to August 2023 on pregnant women from 24 clusters (kebeles) (12 interventions and 12 controls) in the northern zone of the Sidama region. The Open Data Kit smartphone application was utilized to collect data. The intention-to-treat analysis was used to compare outcomes between groups. We fitted multi-level mixed-effects modified Poisson regression with robust standard error to account for between and within cluster effects. Results: One thousand and seventy pregnant women (540 in the intervention and 530 in the control clusters) responded to this study, making the overall response rate 95.02%. Excessive vaginal bleeding (94.3% in the interventional group vs. 88.7% in the control group) was the commonest ODS mentioned during childbirth. Overall, 68.7% of women in the intervention group and 36.2% of mothers in the control group had good knowledge of ODS (P-value < 0.001). Saving money and materials (97.1% in the interventional group vs. 92.7% in the control group) was the most frequently practiced BPCR plan. Overall, 64.3% of women in the intervention group and 38.9% of mothers in the control group practiced BPCR (P-value < 0.001). HEI significantly increased overall knowledge of ODS (adjusted risk ratio [ARR]: 1.71; 99% CI: 1.14-2.57) and improved overall BPCR practice (ARR: 1.55; 99% CI: 1.02-2.39). Conclusions: A community-based HEI led by women's groups improved mothers' knowledge regarding ODS and BPCR practices in a rural setting in southern Ethiopia. Interventions designed to increase women's knowledge of ODS and improve BPCR practice must implement context-specific, community-based HEI that aligns with World Health Organization recommendations. Trial registration: NCT05865873

With the development of the photovoltaic industry, there will be an increasing demand for efficient, high-power density, and low-cost grid interface converters. Compared with two-level inverters, multilevel inverters have the following advantages: (1) lower device voltage ratings; (2) better output filtering spectrum; (3) lower electromagnetic interference (EMI) noise; and (4) higher switching speed capability. However, the complex switching circuit of the multilevel inverter will bring more parasitic inductance, resulting in more serious switching overvoltage (ringing). Consider that commonly used overvoltage absorption schemes are effective only for overvoltage or sup-pression of oscillations. Therefore, a new overvoltage absorption circuit is proposed in this paper, which can not only alleviate the overvoltage and ringing phenomena but also suppress the effect of voltage jumps during low-frequency switching on high-frequency input voltage. This overvoltage absorption circuit is characterized by low overvoltage, fast ringing damping, and minimum ca-pacitance. Experiments and simulations are conducted to verify the effectiveness of this overvoltage absorption circuit using a three-level ANPC inverter as a prototype. The results show that the proposed overvoltage absorption circuit can significantly reduce the overvoltage level, shorten the oscillation time, and reduce the voltage difference between the upper and lower DC bus capacitors.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

Thermostatically controlled loads have great potential to make a significant contribution to improving energy efficiency in the building sector, which is responsible for 40% of greenhouse gas emissions in the EU. This, in addition to the environmental damage, represents a huge expense in the electricity bill. Therefore, it is very important to train engineers on how to design energy management systems for TCLs. With this goal in mind, it would be very useful to have a simulation-based educational tool (SBET) to understand thermostatically controlled loads, their characteristics and possibilities in energy efficiency. In addition, it would be very useful if this tool could be introduced in engineering curricula to help students to be better trained and enter the labor market with more opportunities. Based on the shortcomings detected, this work develops a SBET specifically designed to teach about TCLs (SBET-TCLs), both about their intrinsic characteristics and their better management. To verify the developed SBET-TCL, it has been tested in a real scenario: A survey was carried out among the students of the subject 'Alternative Energy Sources' of the degrees of Industrial Engineering. The results show that the use of SBET-TCL has very positive effects on the learning process.

Transdermal drug delivery systems have become an intriguing research topic in healthcare technology and one of the most frequently developed pharmaceutical products in the global market. In recent years, researchers and pharmaceutical companies have made significant progress in developing new solutions in the field. This study sheds light on current trends, collaboration patterns, research hotspots, and emerging frontiers of transdermal drug delivery. Herein, a bib-liometric and patent analysis of data recovered from Scopus and The Lens databases, respectively, is reported over the last 20 years. From 2000 to 2022, the annual global publications increased from 131 in 2000 to 659 in 2022. Researchers in the United States, China, and India produced the highest number of publications. Likewise, most patent applications have been filed in the USA, China, and Europe. The recovered patents are 7,275, grouped into 2,997 patent families, of which 314 were granted. This study could support the work of decision-makers, scientific managers, or scientists to create new business opportunities or save money, time, and intellectual capital, thus, defining when a research or technology project should be a priority or not.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

In our recent report, we clarified the direct interaction between excitatory amino acid transporter (EAAT) 1/2 and polyunsaturated fatty acids (PUFAs) by applying electrophysiological and molecular biological techniques to Xenopus oocytes. Xenopus oocytes have a long history of use in the scientific field, but they are still attractive experimental systems for neuropharmacological studies. We will therefore summarize the pharmacological significance, advantages, (especially in the study of EAAT2), and experimental techniques that can be applied to Xenopus oocytes; our new findings concerning L-glutamate (L-Glu) transporters and PUFAs; and the significant outcomes of our data. The data obtained from electrophysiological and molecular biological studies of Xenopus oocytes have provided us with further important questions, such as whether or not some PUFAs can modulate EAATs as allosteric modulators and to what extent docosahexaenoic acid (DHA) affects neurotransmission and thereby affects brain functions. By combining Xenopus oocyte experiments and more translational approaches, we can clarify the functions of proteins that are difficult to examine using cultured cells and the physiological roles of these proteins in brain functions. These approaches can lead to the development of the new central nervous system (CNS) drugs targeting molecules and investigations of their effectiveness.

In this research, the concept of the instability of tension in Microgrid still becomes the focus of study and purpose. Scrutinously, First-Swing Instability occurs in the system in noted changes with properties of making the system unstable or restore to a state of stability. The latter calls itself as a phenomenon of re-synchronization. Allied to aspects of system instability, it is evident that by connecting fast electric chargers for battery-electric vehicles to the distribution system from microgrids, they increase the necessary basic electrical charges and reduce the stability of the electrical energy system. Transient electrical currents have the characteristic of severely impacting microgrids not prepared in connected states or island of the main system. The occurrences of the electromagnetic incompatibility of the inrush current, due to their unpredictability and intermittent characteristic, have complex identification studies. With the elevation of electricity demand by battery-electric vehicle chargers, concerns about the effects of the integration of the electricity grid increase proportionally. The research described in this article emphasizes the influence of fast chargers’ initialization on the power variation related to the re-synchronization phenomenon and its mitigation of the stability of electricity microgrid. An optimization algorithm based on particle swarm optimization (PSO) implements the development of virtual impedances. The PSO optimization algorithm analyzes all possible operating points and aims to maximize the stability index of microgrid, maintaining reactive energy incompatibilities at the minimum level supported. The fractional objective function facilitates the service to these goals simultaneously. The optimization algorithm is implemented in a case study and the corresponding virtual impedance is incorporated into the microgrid. Voltage levels are verified as a condition in the optimization process, comparing system effectiveness.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

In this paper, corticosteroid–β-cyclodextrin (β-CD) inclusion complexes have been prepared by Supercritical AntiSolvent (SAS) precipitation to enhance the dissolution rate of dexamethasone (DEX) and prednisolone (PRED), which are poorly water-soluble drugs. The processing of the active principles in the absence of a carrier led to the almost complete extraction of the active principle (the small amount of obtained material precipitates in the form of crystals). The coprecipitation of the ingredients in the presence of β-CD was investigated at different concentrations, pressures, and molar ratios. For both the corticosteroids, the optimized operating conditions were 40 °C, 120 bar, an equimolar ratio, and a concentration in DMSO of 20 mg/mL; these conditions led to the attainment of microparticles with a mean diameter equal to 0.197±0.180 μm and 0.131±0.070 μm in the case of DEX and PRED, respectively. The Job’s method confirmed the formation of inclusion complexes in correspondence with the 1/1 mol/mol ratio. Compared to the pure ingredients, the obtained powders have an improved release rate, which is about 3 times faster in both cases.

(1) Background: Prevention of acute cardiovascular events in patients with cardiovascular diseases (CVDs) requires promoting health-protective behaviors (e.g., physical activity) and preventing health-compromising behaviors (sitting). Digital health interventions provide much potential. Based on multiple behavioral change theory, an intervention (reCardial app) was evaluated, and the following hypotheses were tested: H1: Health behaviors (physical activity, sitting) and disease self-management (self-care maintenance, self-care confidence) are closely interrelated. H2: Change in health behaviors and disease self-management indicators over time is more pronounced in reCardial app-users. H3: In the intervention group, changes in systolic and diastolic blood pressure indicate a positive trajectory. (2) Methods: A study with the design of a randomized controlled trial over 12 weeks was conducted. 40 CVD-patients were randomized equally to the Intervention Group (35% women; Mage=60.6years) and Control Group (45% women; Mage=61.5years). (3) Results: Findings support H1 with significant correlations between health behaviors (r=0.45-0.63**), and disease self-management (r=-0.32-0.54**), H2 with Eta²=0.21 (not statistically significant) and H3 partially with d=0.101 for systolic blood pressure but not regarding diastolic blood pressure. (4) Conclusions: Replications are needed with larger samples and more objective measures. The app can help prevent and manage CVD by means of promoting health-protective behaviors and preventing health-compromising behaviors. Taking different behaviors into account can increase intervention effects and with that support of users.

Aronia berries contain antioxidants that may have health promoting properties e.g., demonstrated positive effects on hypertension and dyslipidemia. There is a close link between cardiovascular diseases and hypertension and dyslipidemia, and cardiovascular events are the leading cause of death among subjects with T2D. Thus, we investigated the effect of 8 weeks supplementation with fermented aronia extract (FAE), non-fermented aronia extract (AE) and placebo on cardiovascular risk factors. The extracts were incorporated into snack bars containing 34 g (37%) aronia extract, or 17 g (21%) wheat bran for placebo, as well as raisins and coconut oil. The study was randomized and blinded with a triple-cross-over design. We examined the effects of aronia extracts on blood pressure, adiponectin and high-sensitive C-reactive protein and found no effects. After supplementation with placebo, there were significantly higher total-cholesterol, LDL-cholesterol, and HDL-cholesterol, with the placebo group showing significantly higher increases in total-cholesterol and LDL-cholesterol than the FAE group. Furthermore, we observed an increase in HDL-cholesterol in the AE group and an increase in triglyceride in the FAE group. Thus, we assume that raisins may have increased the participants’ cholesterol levels, however, with both AE and FAE having the potential to prevent this increase.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

Post-harvest handling and ripening techniques have an impact on peach quality and shelf life, which has a big impact on consumer satisfaction and market competitiveness. This review paper examines recent advancements in ripening techniques and post-harvest technologies with the goal of improving peach fruit quality and sustainability. The factors impacting fruit quality after harvest and the physiological changes that occur throughout peach ripening are fully explained. For maintaining peach freshness and reducing losses, novel handling methods like modified atmosphere packaging (MAP) and controlled atmosphere storage (CAS) have been investigated. The study explores the possibilities of nanotechnology applications and low-temperature storage for prolonging shelf life while maintaining texture, flavor, and aroma. Examining the effectiveness and waste reduction potential of automation and mechanization in post-harvest activities. The paper also discusses ethylene-based and non-ethylene-based ripening agents, as well as innovative techniques including gene editing and RNAi technology for controlled and delayed ripening. Analyses are done on how these technologies affect the sensory qualities and nutrient profiles of peaches. The study emphasizes the significance of sustainable practices in the peach industry by focusing on waste reduction, resource efficiency, and circular economy integration. Post-harvest technologies' potential environmental consequences have been taken into consideration and the paper encourages more study and cooperation to increase sustainability.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Severe COVID-19 alters the biochemical and morphological characteristics of blood cells in a wide variety of ways. To date, however, the vast majority of research has been devoted to the study of leukocytes, while erythrocyte morphological changes have received significantly less attention. The purpose of this research was to identify erythrocyte types that were unique to COVID-19, compare the number of different poikilocyte types, and measure erythrocyte sizes to provide data on size dispersion. Red blood cells obtained from 6 control donors (800-2200 cells for each donor) and 5 COVID-19 patients (800-1900 cells for each patient) were examined using low voltage scanning electron microscopy. We did not discover any forms of poikilocytes that would be unique to COVID-19. Among COVID-19 patients, we observed an increase in the number of acanthocytes (p=0.01) and a decrease in the number of spherocytes (p=0.03). In addition, our research demonstrates that COVID-19 causes an increase in the median (p=0.004) and interquartile range (p=0.009) when assessing erythrocyte size.

This study evaluated gas mixtures of carbon dioxide (CO2) associated with nitrogen (N2) as al-ternatives to the use of CO2 in two phases to improve the welfare of broiler chickens at slaugh-ter. Broilers were exposed to one of three treatments: 40C90C (1st phase: <40% CO2 for 2 min; 2nd phase: >90% CO2 and <2% O2 for 2 min, n=92), 40C60N (40% CO2, 60% N2 and <2% O2 for 4 min, n=79), or 20C80N (20% CO2, 80% N2 and <2% O2 for 4 min, n=72). The time to onset of loss of consciousness (LOC) and death was assessed by brain activity (EEG) and behaviour. Behaviour also allowed characterisation of the aversive response to the treatments. Exposure to 40C60N and 20C80N induced LOC faster (19 s [14 – 30 s] and 21 s [16 – 37 s], respectively) but also with less inter-individual variability compared to 40C90C (53 s [26 – 156 s], P < 0.001) and birds took less time to die (40C60N: 64 s [43 – 108 s]; 20C80N: 70 s [45 – 88 s]; 40C90C: 177 s [89 – 212 s], P < 0.001). The 40C90C birds not only experienced more aversion during induction to LOC but are at risk of remaining conscious when the CO2 concentration is increased in the 2nd phase. From an animal welfare point of view, 40C60N provided the highest welfare, followed by 20C80N and 40C90C.

The main objective of the paper is to provide a thorough analysis of currently used modulation control schemes for single phase bidirectional dual active bridge DC/DC converter. In this article, it will be shown that single phase shift, extended phase shift and Dual phase shift modulation schemes are special cases of triple phase shift (TPS) modulation scheme. The article aims to highlight six TPS switching modes and their complements with the operational constraints. Unlike previous studies that regarded TPS as a complex scheme, this paper simplifies the analysis of each mode and aims to standardize the understanding of TPS modulation in DAB converters. Power equations, range of power transferred and zero voltage switching (ZVS) are derived for all the modes under TPS without assuming fundamental component analysis. Additionally, a generic optimization algorithm is developed to show the advantages of TPS modulation and thus, detailed analysis presented in this paper provides valuable insights for single phase DAB converter designers in identifying a wide range of optimization algorithms to achieve higher efficiency under TPS modulation. This analysis contributes to the advancement of bidirectional DAB converter technology and facilitates its application in various power electronic systems.

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited high water swelling capacity, fast water absorption and high water vapor transmission. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. The drug release kinetics was comparable to that of a commercial PHMB-releasing AMD assayed under the same conditions. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds, and blood clotting activity. The obtained results suggest that these membranes may be suitable for use in the development of AMDs.

Despite the expansion of financial institutions and proliferation of mobile financial services, reaching the unbanked and bringing them under formal financial services has become a policy concern in many developing countries. Due to the lack of financial accounts, unbanked people prefer informal, risky, and inconvenient mechanisms for receiving, sending and transferring money. Previous studies rely much on common intervention like no account maintenance and opening fees, easy documentation processes and money subsidies for opening financial accounts. This study aims to examine the impact of the motivational workshop on opening savings accounts through causality among the unbanked people in a setting where the respondents are unbanked despite having all the requirements and many institutional offers for opening savings accounts. We encouraged the unbanked people through a one-hour-long motivational workshop to open saving account. Based on our cross-sectional data and randomized controlled trial experiment among 505 unbanked Village Defense Party (VDP) members at Dhubil Union under Sirajganj in Bangladesh, we have the evidence that motivational workshop positively impacts opening ac-counts by 32.33 percent. However, the account opening rate differs in terms of respondent’s pref-erence for financial institutions. Our study also finds that unbanked people have the highest pref-erence for mobile financial services for opening accounts resulting in 15.33 percent. The result of the study has some policy implications for adopting effective strategies of financial access in many developing countries.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

(1) Background: The aim of this study is to investigate the diagnostic-therapeutic problem of pelvic recurrence of rectum cancer, highlighting current surgical standards and the possible role of the minimally invasive approach. This retrospective analysis of our surgical case study wishes to enter this debate while suggesting a possible line of action, based on the site of recurrence; (2) Methods: We examined, retrospectively, all the patients diagnosed, between 2008 and 2018, with cancer of the rectum at the "Pietro Valdoni" Department of Surgery and monitored their follow-up for 5 years. The sample consisted of 368 patients with rectal neoplasm, 136 females and 232 males, with an average age of 65.8 (ranging from 37 to 86); (3) Results: In 103 of the cases, the neoplasm was located in the upper rectum (28%), in 119 cases in the middle rectum (32.3%), in 102 cases in the lower rectum (27.7%), in 31 cases (8.4%) at the level of the right/sigma junction and in 13 cases it was not possible to define the site with certainty (3.5%); (4) Conclusions: The discussion re-mains open as to which approach is best at surgical level, whether laparoscopic, robotic or open-air. Our experience informs us that the most dangerous site remains on the anastomotic site.

Thin-film lithium niobate has gained significant attention in photonics due to its broad optical transparency, high refractive index, nonlinear coefficient, and substantial electro-optic coefficient. It holds great promise for developing electro-optic modulators with low loss, a compact size, and wide bandwidth. This study focuses on a meticulous investigation utilizing microwave photonics to establish a high-performance electro-optic modulator. Specifically, we analyze the optical mode field distribution and traveling wave electrode structure of lithium niobate thin-film materials. The proposed modulator achieves an impressive half-wave voltage-length product of 1.69 V·cm, a negligible metal loss of 0.01 dB/cm, and a substantial 3dB electro-optic bandwidth of 50 GHz. This research successfully realizes low-loss, high-efficiency LNOI electro-optical modulators, providing a strong foundation for large-scale integrated optoelectronic systems.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

This article describes rationales and limitations for making inferences based on data from randomized controlled trials (RCTs). We argue that obtaining a representative random sample from a patient population is impossible for a clinical trial because patients are accrued sequentially over time and thus comprise a convenience sample, subject only to protocol entry criteria. Consequently, the trial’s sample is unlikely to represent a definable patient population. We use causal diagrams to illustrate the difference between random allocation of interventions within a clinical trial sample and true simple or stratified random sampling, as done in surveys. We argue that group-specific statistics, such as a median survival time estimate for a treatment arm in an RCT, have limited meaning as estimates of larger patient population parameters. In contrast, random allocation between interventions facilitates comparative causal inferences about between-treatment effects, such as hazard ratios or differences between probabilities of response. Comparative inferences also require the assumption of transportability from a clinical trial’s convenience sample to a targeted patient population. We focus on the consequences and limitations of randomization procedures in order to clarify the distinctions between pairs of complementary concepts of fundamental importance to data science and RCT interpretation. These include internal and external validity, generalizability and transportability, uncertainty and variability, representativeness and inclusiveness, blocking and stratification, relevance and robustness, forward and reverse causal inference, intention to treat and per protocol analyses, and potential outcomes and counterfactuals.

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, aiming to protect the DFIG and power converters, and consequently, improve the system’ ability to ride-through faults. Further, the capacity of an energy storage device for transient suppression is estimated. Finally, simulation results show that the proposed approach is effective in achieving transient control objectives precisely and maintaining a stable grid connection during the faults.

Objective: To evaluate the existing meta-analytic evidence of associations between exposure to ultra-processed foods, as defined by the Nova food classification system, and adverse health outcomes. Design: Systematic umbrella review of existing meta-analyses. Data Sources: MEDLINE, PsycINFO, Embase, and the Cochrane Database of Systematic Reviews, as well as manually searching reference lists from 2009 to June 2023. Inclusion Criteria: Systematic reviews and meta-analyses of cohort, case-control, and/or cross-sectional study designs that evaluated the associations between exposure to ultra-processed foods and adverse health outcomes in humans across the lifespan. Results: The search identified 45 unique pooled analyses, including 13 dose-response and 32 non-dose-response associations (n=9,888,373). Overall, direct associations were found between exposure to ultra-processed foods and 32 (71%) health outcome domains spanning cardiometabolic, gastrointestinal, and respiratory conditions, cancer, mental health, and mortality. Based on a pre-specified evidence classification criteria, convincing evidence (Class I) supported direct associations between greater ultra-processed food exposure and higher risks of incident cardiovascular disease-related mortality (RR: 1.50; 95%CIs: 1.37 to 1.63), type two diabetes (dose-response RR: 1.12; 95%CIs: 1.11 to 1.13), and depressive outcomes (HR: 1.21; 95%CIs: 1.16 to 1.28), as well as higher risks of prevalent anxiety outcomes (OR: 1.48; 95%CIs: 1.37 to 1.59) and combined common mental disorder outcomes (OR: 1.53; 95%CIs: 1.43 to 1.63). Highly suggestive (Class II) evidence indicated that greater exposure to ultra-processed foods was directly associated with higher risks of incident all-cause mortality (RR: 1.21; 95%CIs: 1.15 to 1.27), heart disease-related mortality (dose-response HR: 1.66; 95%CIs: 1.51 to 1.84), and type two diabetes (OR: 1.40; 95%CIs: 1.23 to 1.59), together with higher risks of prevalent obesity (OR: 1.55; 95%CIs: 1.36 to 1.77), adverse sleep-related outcomes (OR: 1.41; 95%CIs: 1.24 to 1.60), and wheezing (RR: 1.40; 95%CIs: 1.27 to 1.55). Out of the remaining 34 pooled analyses, 21 were graded as suggestive or weak strength (Class III-IV) and 13 were graded as no evidence (Class V). Using the GRADE framework, 22 pooled analyses were rated as "Low" quality, with 19 rated as "Very Low” and four rated as "Moderate" quality. Conclusions: Higher exposure to ultra-processed food was associated with a greater risk of adverse health outcomes, especially cardiometabolic, common mental disorder, and mortality outcomes. These findings provide a rationale to evaluate the effectiveness of using population-based measures to target and reduce dietary exposure to ultra-processed foods for improved human health. Systematic Review Registration: PROSPERO CRD42023412732.

Basil (Ocimum basilicum L.) is one of the important medicinal and aromatic plants. Light intensity is an indispensable factor for plants due to its effect on photosynthesis and physiological processes. Here, we investigated the impact of light intensities and harvesting times on the photosynthesis of green and purple basil. The experiment involved subjecting the plants to three different sunlight levels for 12 days: complete – 100%, 50%, and 30% sunlight. In addition, we scrutinize the harvesting time. The highest levels of photosynthetic and protective pigments were detected under full sunlight conditions in the purple basil harvested at noon. The highest levels of soluble and storage carbohydrates were recorded in the purple basil grown under full sunlight and harvested in the early morning. In contrast, their lowest levels were obtained in plants grown under 30% sunlight and harvested at noon time. Under all light treatments, the maximum quantum yield of photosystem II (FV/FM) was detected at 4 a.m. in both basil varieties; it decreased at noon and increased again at 5 p.m. Non-Photochemical Quenching (NPQ) got most elevated in the green variety under all light intensities at noon. However the highest NPQ was detected in the purple variety at 8 a.m. The NPQ was lowest in both basil varieties during the early morning and afternoon. Full sunlight at noon caused temporary photoinhibition and reduced car-bohydrates while enhancing pigment concentration and photo-protective mechanisms in basil plants.

Background: In this secondary analysis of the Supporting the Modification of Lifestyle In Lowered Emotional States (SMILES) randomised controlled trial, we investigated if the beneficial effects of a dietary intervention on clinical depression were driven, in part, by reducing the consumption of foods classified as ultra-processed.Methods: The SMILES trial enrolled 67 adults with major depressive disorder, randomly assigning them to either a 12-week modified Mediterranean dietary intervention or a social support control. Our analysis included 44 participants with non-missing dietary data and at least one valid Montgomery–Åsberg Depression Rating Scale (MADRS) assessment at 12 weeks of follow-up. The Nova food classification system was used to estimate the proportion of ultra-processed foods in the overall diet (percentage of grams) based on data from seven-day food diaries. We fitted linear regression models under blinded conditions to determine whether ultra-processed food intake-change from baseline to 12 weeks moderated the dietary intervention effects on depressive symptoms. We estimated mean differences in depressive symptoms along with ninety-five per cent confidence intervals (95%CIs).Results: For participants in the dietary intervention, there was an additional 2.5-point improvement in MADRS scores for each 10% reduction in the dietary share of ultra-processed foods compared to participants in the control group (between-group mean differences in depressive symptoms: −2.46, 95%CIs −4.71 to −0.20, p=0.039, η _p ² of 0.10).Conclusions: These preliminary findings suggest that the therapeutic benefit of a dietary intervention for depression may stem, at least in part, from reductions in the dietary share of ultra-processed foods.

Today electricity is distributed to the individual users via physical Copper connections. From the power stations, the energy is transported through transmission lines where the electricity, sinusoidally modulated at a fixed frequency of about 50 Hz, is raised up to a voltage in a range approximately variating between 30, and 110 kV. When electrons, aligned at this voltage, pass through the transmission lines, they cause coherent vibrations, sometimes even audible in the acoustic frequencies. In the spectrum of movements to which electric cables are subjected, there are also unexpected and sporadic movements caused by winds and rain. The problem of carrying out persistent, precise and spatially distributed monitoring of transmission line health is to use a large number of sensors physically distributed everywhere and somehow transmit the results to a control station. The use of synthetic aperture radar (SAR) data could be a viable solution of persistent and wide-area high-voltage vibration monitoring. In this paper we produce a comprehensive survey on how to monitor both movements in terms of vibrational displacement, due to weathering, and those due to electricity transmission, normally fixed at about 50 Hz. The results demonstrate the technical feasibility of an operational use of SAR for these purposes in the very short term. This would allow the possibility of monitoring malfunctions such as black-outs or other frequency anomalies.

Variations in threshold voltage (VTH) and charge distributions in noncircular cells of three-dimensional (3D) NAND flash memory are investigated. The electric field difference in the circular and spike regions causes nonuniform trapped electron density in the charge trap layer (CTL) and influences the VTH variation. Such less-trapped electron (LT) regions in CTL between the circular and spike regions exhibit a lower electric field during the program, resulting in a higher current flow through that region. For the two-spike cells, the charge distribution and VTH variation are analyzed at different heights (HSpike) and angles between spikes. These irregular cells decrease VTH as the HSpike increases.

Breast cancer is the most common malignant disease in women. Preclinical studies have confirmed that the local anesthetic levobupivacaine has a cytotoxic effect on breast cancer cells. We examined whether postoperative wound infiltration with levobupivacaine influences survival in 120 patients who were operated on for breast cancer and underwent quadrantectomy or mastectomy with axillary lymph node dissection. Groups with continuous levobupivacaine wound infiltration, bolus wound infiltration, and diclofenac analgesia were compared. Long-term outcomes examined were quality of life, shoulder disability, and hand grip strength (HGS) after one year, and survival after 5 and 10 years. Groups that had infiltration analgesia had better shoulder function compared to diclofenac after one year. Levobupivacaine PCA group had the best preserved HGS after 1 year (P=0.022). The most significant predictor of the 5-year outcome was HGS (P=0.03). Although the best survival after 5 and 10 years was registered in the bolus levobupivacaine group, statistical significance was not reached (P=0.36). The extent of the disease at the time of surgery is the most important predictor of long-term survival. A larger prospective clinical study could better confirm the effect of levobupivacaine wound infiltration on outcomes after breast cancer surgery observed in this pilot study. Trial number NCT05829707

In order to reduce the risk of grid transient voltage instability brought about by the new energy and system dynamic loads and the increasing proportion of new energy access, this paper proposes a differentiated dynamic reactive power compensation configuration method for suppressing transient voltage dip instability. The method first establishes a dynamic reactive power device configuration index system based on a multi-binary table, and then establishes a differentiated dynamic reactive power compensation device configuration model based on the node instability risk characteristics by combining with the regional division of system transient voltage instability risk. The model takes the investment cost and suppression effect as the optimization objectives, and realizes differentiated dynamic reactive power compensation by flexibly adjusting the optimization weights of economic benefits and reactive power compensation effects in the configuration process; Compared with the traditional compensation methods, differentiated compensation can significantly improve the economic benefits of reactive power compensation configuration. Finally, taking the IEEE39 node test system as an example, the improved TLBO algorithm is used to solve the model, which verifies the accuracy and effectiveness of the method proposed in this paper.

The structure and phenomena arising from charge transfer in cold field emission modus in a single closed carbon nanotube under cold field emission conditions were studied. By studying microphotographs in various microscopes - AFM, SEM, TEM it was found inhomogeneities in the form of two types of superlattices. The conductivity of the emitter section of a nanodiode circuit with an emitter made of an individual closed carbon nanotube (CNT) and arrays of closed CNTs was studied. High values of cold field emission were observed, as well as nonlinearity and anomalies of the current-voltage characteristic (I-V characteristics), which manifested themselves in the form of peaks at low and high current values. Peaks in the CVC have distinct areas of negative differential conductivity. It is argued, that the anomalously high currents in the I–V characteristics of cold field emission of electrons from a nanoemitter made of closed CNTs can be associated with a sharp increase in the density of electron states at energies near the van Hove singularity.

In this paper, stochastic multi-objective intelligent framework (MOIF) is performed for distribution network reconfiguration to minimize power losses, the number of voltage sags, the system's average RMS fluctuation, the average system interruption frequency (ASIFI), the momentary average interruption frequency (MAIFI), and the system average interruption frequency (SAIFI) considering the network uncertainty. The unscented transformation (UT) approach is applied to model the demand uncertainty due to simplicity to implement and no presumptions to simplify. A human-inspired intelligent method named improved mountaineering team-based optimization (IMTBO) is applied to determine the decision variables defined as the network's optimal configuration. The conventional MTBO is improved using a quasi-opposition-based learning strategy to overcome premature convergence and achieve the optimal solution. The simulation results showed that in single- and double-objective optimization, some objectives are weakened compared to their base value, while the results of the MOIF indicated a fair compromise between different objectives, and all objectives are improved. The results of MOIF based on the IMTBO cleared that the losses are reduced by 30.94%, the voltage sag numbers and average RMS fluctuation are reduced by 33.68% and 33.65%, and also ASIFI, MAIFI, and SAIFI are improved by 6.80%, 44.61%, and 0.73%, respectively. Also, the superior capability of the MOIF based on the IMTBO is proved compared to the conventional MTBO, particle swarm optimization, and artificial electric field algorithm. Moreover, the results of the stochastic MOIF based on the UT showed the power loss increased by 7.62%, voltage sag, and SARFI increased by 5.39% and 5.31%, and ASIFI, MAIFI, and SAIFI weakened by 2.28%, 6.61%, and 1.48%, respectively compared to the deterministic MOIF model.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

This work deals with the synthesis of bare and curcumin (CUR)-loaded chitosan (CS)-based macroparticles by ionic gelation using sodium hydroxide (NaOH) or sodium tripolyphosphate (TPP) as cross-linking agents. The resulting spherical-shaped macroparticles were studied using various characterization techniques, Scanning Electron Microscopy (SEM), Fourier Transformed Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), and Differential Scanning Calorimetry (DSC). The release of CUR from the CS-based particles with respect to time was analyzed, and the encapsulation efficiency and degree of swelling were studied. All formulations showed excellent CUR trapping efficiency, exceeding 90%. In particular, the TPP-crosslinked macrobeads released 34 wt% of the charged CUR within minutes, while the remaining 66 wt% was released slowly due to the biodegradation of CS. The results indicate that the correct choice of gelling agent and its concentration leads to spherical particles capable of encapsulating CUR and releasing it in a wide range of kinetics depending on the specific application.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

The development and qualification of CrAlN coatings deposited by DC magnetron sputtering offer new industrial solutions to increase the lifecycle of material forming tools (machining and shaping). This study focuses on the selection and optimization of deposition modes for CrAlN layers to be deposited on a 90CrMoV8 tool steel substrate. The adopted methodology aims to optimize the deposition conditions to meet the customer's requirement of a CrAlN coating thickness of approximately 2-3 µm for use in a hot forming process. Different polarizations using two Al and Cr targets, with both stationary and rotating substrate modes during deposition, were tested and evaluated. Characterizations of the CrAlN coating layers (microhardness, residual stress, structures) and performance in service (wear, friction, adhesion, corrosion) were chosen as selection criteria for a particular coating mode. The aluminum content plays a crucial role in the tribological and mechanical behavior of CrAlN layers. Corrosion resistance is more sensitive to the aluminum content for the stationary deposition mode. As a result, the rotating mode provides higher adhesion (+100%) and less wear (-60%) compared to the stationary mode. Therefore, depending on the likely performance in service, either a stationary or rotating mode could be applied for coating the functional surfaces of hot forming tools.

Agriculture technical development exclusively relies on the effective delivery of agrochemicals and water to the plants and reduce the harmful effects of the agrochemicals on the useful organisms in the soil. Wherefore, super absorbent hydrogels were prepared by copolymerization of gum Arabic (GA) with chitosan (CS) or poly(vinyl alcohol) (PVA), and cross-linked by N,’N-methylenebisacrylamide (MBA) chemically (CH) or using sodium hexametaphosphate (SHMP) as physical (PH) cross-linker. The prepared hydrogels include PVA/GA-CH, PVA/GA-PH, CS/GA-CH and CS/GA-PH showed different degree of swelling (DS) in the following swelling medium, deionized water (DW), river water(RW) and buffer solution pH9. PVA/GA-CH and CS/GA-CH hydrogels have showed 84g/g and 63g/g maximum DS in RW respectively, while PVA/GA-PH and CS/GA-PH hydrogels have showed 81g/g and 69g/g maximum DS in pH9 respectively. The water- retention capability of some hydrogels were studied using a mixture of 0.5%(w/w) hydrogel in agricultural soil and the composite showed about 20 days extra retain of water with a control sample of soil alone. The hydrogels were loaded using urea the important fertilizer in agriculture field. The hydrogels of higher DS were only loaded, where PVA/GA-CH hydrogel has shown 89%(w/w) maximum loading percentage (Lmax%), and CS/GA-PH hydrogel reached 79.75%(w/w) of urea. The release behavior in different medium and degree of temperatures of loaded hydrogels were studied. Generally, PVA/GA-CH hydrogel have shown better release profile in RW medium at 10oC, while CS/GA-PH hydrogel showed more controlled release in pH9 medium at 30oC. Different analytical methods of SEM, FTIR of loaded hydrogel and after their release were achieved, whereas XRD,1H NMR and (TGA, DSC) of prepared hydrogels have been characterized.

Power converter technologies have become increasingly vital in various applications due to their efficient management of electrical energy. With the growing prominence of renewable energy sources like solar and wind, the high penetration of power electronic converters has been justified. However, ensuring power quality has emerged as a significant challenge for grid-connected power converters. The divergence from the ideal sinusoidal waveform in terms of magnitude and frequency impacts both grid-side currents and voltages. Several studies have proposed solutions to address power quality issues at the load side. The advancement of power converters has been fueled by the development of high-performance microprocessors and the emergence of high-speed switching devices, such as SiC-MOSFETs. This paper focuses on the design of voltage source converters, particularly those based on SiC-MOSFET semiconductor devices. The article presents the design of H-Bridge cells, discusses two-level voltage source converters based on cascade H-Bridge cells in parallel configuration with experimental fault analysis, addresses the seven-level voltage source converters topology, and explores the design and experimental results of the matrix converter. The findings underscore the importance of considering the entire converter design for improved performance at high switching frequencies. The article concludes by summarizing the main outcomes and implications of this research.

The cross-linked microspheres were prepared and loaded with Favipiravir SARS-CoV-2 antiviral drug, by copolymerization of chitosan (CS) with a polysaccharide extracted from fresh pomegranate peels. Moreover, glutaraldehyde (Glu) has been used as chemical cross-linker ,and sodium hexametaphosphate (SHMP) as physical cross-linker. The extracted polysaccharide was analyzed and different techniques have been used and the analyses leads to the fact that it is pectin .The surface morphology of the prepared microspheres was studied use scanning electron microscope where the size and the shape factor (S) of Glu microspheres have shown high values(74.27μm) and (0.852) respectively means their surfaces are tends to roughness, whereas the SHMP microspheres have shown size particle(20.47μm)and shape factor (0.748) which gives indication that the SHMP microspheres have smooth surfaces. The swelling studies have shown that Glu microspheres have higher degree of swelling which means SHMP microspheres are more compact. The prepared microspheres have shown more Loading percentage of Favipiravir antiviral drug in SHMP microspheres(37%w/w)in comparison with Glu microspheres(35%w/w) where the electrostatic interaction between the Favipiravir ions and SHMP anions help for more loading. The microspheres prepared under different types of cross-linking have shown initially burst release of Favipiravir and followed by a step of controlled release for a certain time where its period depends on the pH of the release media. Both Glu and SHMP cross-linked microspheres have shown high controlled release time in buffered release solution of pH 7.4 and for a less periods in pH 1.3 and pH 9.4 which may related to the type of electrostatic interactions between drug and polymer system and their reactions with release solution ions.

The outer membrane of Gram-negative bacteria contains a variety of pore-forming structures collectively referred to as porins. Some of these are voltage-dependent, but weakly so, closing at high voltages. Triplin, a novel bacterial pore-former, is a three-pore structure, highly voltage dependent, with a complex gating process. The three pores close sequentially: pore 1 at positive potentials, 2 at negative and 3 at positive. A positive domain containing 14 positive charges (the voltage sensor) translocates through the membrane during the closing process and the translocation is proposed to take place by the domain entering the pore and thus blocking it resulting in the closed conformation. This mechanism of pore closure is supported by kinetic measurements that show that in the closing process the voltage sensor travels through most of the transmembrane voltage before reaching the energy barrier. Voltage-dependent blockage of the pores by polyarginine but not by a 500 fold higher concentrations of polylysine, is consistent with the model of pore closure, with the sensor consisting mainly of arginine residues, and with the presence, in each pore, of a complementary surface that serves as a binding site for the sensor.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

In this study, a new methodology based on the circuit approach is employed to obtain renewable electric energy. Although a voltage source and a current source generate voltage and current, respectively, they work only when they receive electric power, which is the product of voltage and current. However, this paper proposes a circuit with a voltage source, a current source and a super-condenser connected in series, in which the voltage source provides voltage for the current source and the current source provides current for the voltage source. Resultantly, electric power is generated both at the voltage and current sources, and the energy (i.e., the electric power) from the current source is converted to the charging energy in the super-condenser. Herein, we describe the method for charging the super-condenser using a voltage source and a current source. To confirm the abovementioned concept, we conducted experiments, and the energy was successfully produced, with high reproducibility. Finally, the brief mechanism for the energy conversion, a schematic method for reducing the capacitances of stored batteries, and the significance of this study are described.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

The correct classification of defects originating from partial discharges (PD) in medium-voltage (MV) switchgears with air insulation (AIS) remains a challenging research topic for scientists worldwide. In this article, the authors simulated four possible defects occurring in the power industry, including one that is a simultaneous combination of two commonly ones. In addition, the correctness of the algorithm was checked by adding a classification class without any fault. The measurement signals were recorded with TEV sensors. The effectiveness of various hy-brid-connected neural networks was tested and discussed: GoogleNet and SqueezeNet based on spectrograms, SAE with FNN, 2D-CNN with LSTM, and hybrid AE combined with CNN and LSTM. The highest effectiveness – approximately 97% – was demonstrated by the GoogleNet and SqueezeNet networks. The research results are expected to form the basis for the development of a universal and wireless capacitive sensor for monitoring the level of PD in switchgears.

Currently, there are different types of technology for the production of electricity that use various energy sources, this causes the establishment of generation centers that provide from a small amount to tens of megawatts of electrical energy. These centers are built to supply electricity to nearby loads through networks integrated into a large electrical system or in isolation with their electrical system. The technological evolution, the different energy sources, and the generation centers close to the consumers entail what has been called a distributed generation (DG), the DG carries with it aspects that need to be analyzed. In this paper, the impact of wind generation on the medium voltage energy distribution network is studied, it was determined that the addition to the distribution network of power by wind turbines less than the transmission center does not produce an impact on the network. Simulated results obtained using SIMULINK and DIgSILENT are presented and discussed.

Tuberculosis (TB) associated with diabetes (DM) is a growing problem, particularly in low and medium-resource countries. We conducted an open-label, parallel-group, randomized, and controlled trial in a tertiary care center in Mexico City to assess TB preventive treatment with isoniazid (INH) or rifampicin (RIF) in people with DM. Participants were assigned six months of INH 300mg/day plus pyridoxine 75mg or three months of RIF 600mg/day. The primary outcomes were adverse events resulting in permanent treatment cessation and considered possibly or probably related to study drugs. We included 130 subjects, 68 randomized to INH and 62 to RIF. We prematurely halted the study based on recommendations of the Adverse Event Safety Panel. There was no difference between arms in the overall frequency of adverse events. However, the INH group had significantly more permanent treatment interruptions due to grade 2 recurrent or grade 3 or 4 hepatoxicity. In comparison, the RIF arm had more treatment interruptions due to grade 3 or 4 gastrointestinal intolerance. TB preventive treatment is not safe enough to be considered a universal indication to patients with DM and LTBI. These results underline the need to search for alternative TB prevention in DM patients with better safety profiles.

Transdermal drug delivery (TDD) is one of the key approaches for treating diseases, avoiding first-pass effects, reducing systemic adverse drug reactions and improving patient compliance. Microneedling, iontophoresis, electroporation, laser ablation and ultrasound facilitation are often used to improve the efficiency of TDD. Among them, microneedling is a relatively simple and efficient means of drug delivery. Microneedles usually consist of micron-sized needles (50-900 μm in length) in arrays that can successfully penetrate the stratum corneum and deliver drugs in a minimally invasive manner below the stratum corneum without touching the blood vessels and nerves in the dermis, improving patient compliance. Hydrogel-forming microneedles (HFMNs) are safe, non-toxic, no residual matrix material, high drug loading capacity, controlled drug release and are suitable for long-term, multiple drug delivery. This work reviewed the characteristics of skin structure and transdermal drug delivery; introduced TDD strategies based on hydrogel microneedles; summarised the characteristics of HFMNs TDD systems and the evaluation methods of HFMNs; and the application of HFMNs drug delivery systems in disease treatment. The HFMNs drug delivery system has a wide scope for development, but the translation to clinical application still has more challenges.

Concern about the planet's future has motivated governments around the world to adopt policies that promote more responsible energy consumption. Reducing emissions of the principal cause of climate change man-made greenhouse gases requires greater system efficiency and the utilization of renewable energy sources. The generation of electricity is the single largest source of hazardous pollutants, followed by the transportation sector. This is true due to the extreme reliance on petroleum and its derivatives that these industries have. Electric mobility is receiving more attention from businesses, governments, and academic institutions as a means to reduce the negative impacts of current energy consumption. Without measures to address common technical issues, electric vehicles would strain electrical infrastructure. In order to determine the best strategy for switching operations and feeder reconfiguration, this research presents a helpful hybrid genetic algorithm particle swarm optimization (HGAPSO) method. Meet transmission limits while decreasing real power losses and enhancing the system's bus voltage profile. The effects of HGAPSO on power losses and voltage distributions in the network are analyzed. Then, a report is produced contrasting GA and PSO. This cross-breeding of GA and PSO led to HGAPSO. This important problem can be solved more effectively with the use of new or improved algorithms. To find the optimal reconfiguration and properly rearrange transmission network interconnection, it employs a plethora of heuristic optimization algorithms. The objective is to limit bus voltage variations while maintaining the system's radial topology and minimizing power usage. The reliability and performance of the procedure were evaluated using MATLAB's IEEE 33-bus communication network. The outcomes demonstrate the effectiveness of the proposed technique, which cuts down on power waste during standalone runs and speeds up the processing time.

FACTS devices provide significance to enhance the functioning of both static and dynamic power systems. The type, size, and location of FACTS devices determine how well they achieve the goals of enhancing voltage stability, loadability, and loss minimization simultaneously. The aim of the function in this study includes voltage stability, line loadings, and loss minimization, which are expected to obtain the most benefits from their installation and other weights allocated to them. It has been determined how installing TCSC, and SVC will improve loadability under situations of continuously increasing load. In this study, a novel optimization technique known as differential evolution invasive weed optimization (DEIWO) is utilized to locate the optimal location for FACTS devices within the IEEE 14 bus system by considering valve point effects. DEIWO was a recently developed, dominant, and simple metaheuristic algorithm for genuine parameter optimization. DEIWO was inspired by the natural process of weed colonization and dissemination, and it is highly effective at addressing broad multi-dimensional, linear and nonlinear optimization problems. The proposed method was implemented in the IEEE 14 bus testing system. Different methods from the research papers have been used to compare and analyze the results. The results demonstrate the DEIWO algorithm's capability and show how it may be used in practice to locate FACTS devices in deregulated electricity networks in the most advantageous place. A comparison of the proposed process to existing algorithms found in the literature and implemented using traditional techniques reveals that it performs better in terms of precision and convergence

This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.

In this paper, based on the pseudo-totem pole (PTP) circuit, a family of five-level PTP dual boost converters (PDBC) is proposed. Dual boost converter has some unique advantages such as no bridge arm shoot-through risk and no switch body diode reverse recovery problem, so that it has a good application prospect. Compared with conventional three-level PTP converters, PDBCs has higher power density, higher efficiency, and low voltage and current stress. The topological derivation process, working principle, modulation and strategy of the topology are analyzed firstly. Further, the number of power devices, the switches voltage and current stress of the proposed topology is analyzed. Finally, a representative five-level PDBC experimental prototype is designed with AC input 220V/50Hz, DC output 400V/1kW, and peak efficiency of 98.27%. The experimental results show that the five-level PDBC proposed in this paper has higher efficiency and verify the correctness of the topology.

Electric vehicles (EVs) will have a greater need for the amount of electricity needed to charge them as their popularity grows. It is anticipated that in order to accomplish this objective, it will be essential to implement a variety of solutions for grid transportation that are designed to complement one another and to make significant changes to the transmission infrastructure. It is possible to reduce the amount of energy that is lost on the power network through strategic planning and control, which may include economic models and methods to engage and reward users. This would eliminate the need for grid upgrades. Charging electric vehicles can also assist alleviate problems with transmission systems that are caused by the allocation of electric vehicles (EVs) using bidirectional charging method. The most significant problems that can occur with a transmission network are power loss and unstable voltage. Adding EV units to the transmission network is typically an effective method for resolving these challenges. As a result, EVs need to have the appropriate arrangement and dimensions. This research establishes where and how many electric vehicles (EVs) should be in a radial transmission network both before and after the adjustment is made. An artificially intelligent (AI) approach, known as a hybrid genetic algorithm particle swarm optimization (HGAIPSO), is used both before and after the radial network modification to find the optimal EV location and size. When electric vehicles are coordinated in an active transmission network, power losses are decreased, voltage profiles are raised, and system stability is increased. These benefits can be attributed to the greater use of electric vehicles. The simulation found that incorporating EVs into the testing system resulted in a considerable decrease in the quantity of power that was wasted. The minimal bus voltage of the system also undergoes similar kinds of enhancements. According to the findings of the comparative study, the proposed method mitigates both the voltage fluctuations and the power losses that occur in the transmission system. For type 1, type 2, and type 3 EV allocations, the IEEE-30 bus test system reduced real power loss by 40.70%, 36.24%, and 42.94%, respectively. IEEE-30 bus voltage reaches 1.01 pu.

Chronoamperometric curves of the oxidation of a ferrocenyl derivative by the potential step showed diffusion controlled-like currents less than the Cottrell's equation at a platinum wire electrode. The lower deviation cannot be explained by the Butler-Volmer heterogeneous kinetics, but was ascribed to the negatively capacitive current associated with the redox reaction. The deviation at the fully oxidized potential corresponds to the non-zero concentration at the electrode surface, which cannot be predicted from the Nernst equation. The Nernst equation expresses the relationship of the potential with the activity at the electrode surface rather than the concentration. The diffusion equation provides the relation of the current with the surface concentration rather than the activity. The negative capacitance or the non-zero concentration may arise from structure formation on the electrode owing to the dipole-dipole interaction, which is similar to the generation of the double layer capacitance including frequency dispersion. On this concept, we derive here expressions for the lowered diffusion-controlled current and the time-dependent surface concentration. The negatively capacitive current shows the time-dependence of t-0.9, which is similar to the decay of the double layer capacitive currents. The surface concentration decays with the t-0.4-dependence.

Honey bees (Apis mellifera L.) express complex behavioral patterns (aggressiveness) to exhibit defensive mechanisms for their survival. Their phenotypic expression of aggressive behavior is influenced by internal and external stimuli. Knowledge of this behavior is recently important though beekeepers are still faced with the challenges of selecting aggressive and less-aggressive bred lines. Field evaluation of aggressiveness among bred lines of honey bees is required to overcome the challenges. Chemical cues (alarm pheromone and isopentyl acetate mixed with paraffin oil), physical and visual stimuli (dark leather suede, colony marbling and suede jiggling) were used to evaluate aggressiveness and orientation among five bred lines of honeybee colonies. Our results showed that both chemical assays recruited bees but the time of recruitment was significantly lower for alarm pheromone. Honeybees’ response to both assays culminated to stings which differed among bred lines for alarm pheromone and paraffin when colonies were marbled. Honeybee aggression varied among bred lines and was higher in more aggressive bred lines compared to less-aggressive bred lines. Our findings suggest that it is crucial to repeatedly evaluate orientation aggressiveness at the colony level and among bred lines when selecting breeding colonies.

This study employed a TSMC 0.18-µm 50 V process to establish a high-voltage n-LDMOS structure. In the reference device, the number of floating-poly (poly-2) turns was 7, and the width and spacing of each turn was 1 µm. Although increasing the number of turns reduces the peak field, directly reducing or increasing the number of poly-2 turns is a common practice. The present experiment was realized in three steps, namely fixing the number of occupied area adjustment turns, adjusting the width of each turn, and adjusting the distance between turns. The first step was fixing the number of occupied area adjustment turns. The number of turns was increased from 7 to 9, and the number of turns was reduced to 5 and 3 in the reference group. A reduction in the number of turns led to a greater decrease in the peak field and increase in the breakdown voltage despite the area remaining unchanged. A comparison of the use of three turns with that of seven turns revealed that the maximum electric field decreased by 42%, from 4.17e+3 to 2.46e+3 V/cm, and that the breakdown voltage (VBK) increased from 30.2 to 35.84 V. The second step was adjusting the width of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. This increase in width reduced the maximum electric field and led to a greater increase in VBK. When the width was increased to 1.4 µm, the maximum electric field decreased by 29% from 1.95e+3 to 1.4e+3 V/cm, and the VBK increased by 183% from 30.2 to 85.6 V. The third step was adjusting the spacing of each turn from 1 to 1.4, 1.2, 0.8, and 0.6 µm in the reference group. The results revealed that a reduction in the spacing led to a greater reduction in the maximum electric field and an in-crease in the VBK. When the pitch was reduced to 0.6 µm, the maximum electric field decreased by 33%, from 1.95e+3 to 1.32e+3 V/cm, and the VBK increased by 345%, from 30.2 to 134.4 V.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

This paper presents a proposal for a non-isolated bidirectional converter (NIBC) controlled by a deep neural network (DNN) to enable vehicle-to-vehicle (V2V) and vehicle-to-grid (V2G) charging, which contributes to the development of more efficient and sustainable transportation and energy systems. The DNN controller manages power flow in both directions, making it possible to charge electric vehicles (EVs) and discharge power from EVs to the grid with improved efficiency and performance compared to traditional control methods. The non-isolated topology used in this proposal offers several benefits, including reduced cost, smaller size, and higher efficiency. To train the DNN controller, a large dataset of simulations was used, and the results were validated with a hardware setup. The real-time performance of the DNN controller was compared to a proportional-integral (PI) based controller through simulated results. The findings of the study show that the DNN controller outperforms traditional PI controllers.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Wind power generation is one of the mainstream renewable energy resources. Voltage stability is as important as the frequency stability of a power system with a high penetration of wind power generation. The advantages of high-voltage direct current (HVDC) transmission systems become more significant with the increase of both installed capacity and transmission distance in offshore wind farms. Therefore, this study discusses about various voltage control methods for wind turbines and HVDC transmission systems. First, various voltage control methods of a wind farm were introduced, and they include QV control and voltage droop control. The reactive power of a wind turbine varies with active power, while the active power from each wind turbine may be different owing to wake effects. Thus, QV and voltage droop control with varying gain values were also discussed in this paper. Next, the voltage control methods for a HVDC transmission system, such as power factor control, voltage control, and Vac-Q control, are also summarized and tested in this study. When a three-phase short circuit fault occurs or a suddan reactive power load increases, the system voltage would drop immediately. Thus, various voltage control methods for wind turbines or HVDC can make the system's transient response more stable. Therefore, this study implemented the simulation scenarios, including a three-phase short circuit fault at the point of common coupling (PCC) or a sudden increase of reactive power load, and adopted various voltage control methods, which aims to verify whether additional voltage control methods are effective to improve the performance of transient voltage.

With the widespread application of Voltage Source Converter (VSC) in the power system with high penetration of renewable resources, the problem of wideband oscillations caused by the interaction between the power converters and the power grid has drawn large attention. This paper presents a new methodology for simplifying the mathematical derivations of the impedance model of VSC. Using the new simplified model, the stability and the spectrum characteristic of the performance of the VSC can be clearly analyzed. The proposed second-order d-q impedance model of the grid connected VSC at presence of PLL, not only mathematically proves that the wideband oscillatory modes always occurs in conjugate pairs, but also deliver a clear vision of the physical essence of the wideband oscillations. The classic modal analysis is executed in the paper to demonstrate the stability and frequency spectral characteristics of the wideband oscillations in the VSC integrated system. The impact of control parameters of the VSC on the wideband oscillatory stability is thouroughly analyzed using the results of the modal analysis. The methodology can be considered a powerful tool for the control design of VSC in the modern power system.