In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

Biodiesel is considered valuable to reduce dependency on petro-fuels. This work aimed to synthesize biodiesel from Silybum marianum using synthesized ZnO nanoparticles as a catalyst. The synthesized ZnO nanoparticles were examined by scanning electron microscopy and X-ray diffraction for confirmation. The synthesized biodiesel was confirmed by ASTM D-6751, H and C-NMR, GC-MS, and FT-IR spectroscopy. The optimal biodiesel yield of 91% was obtained in the oil-to-methanol ratio of 1:24, 15 mg of catalyst concentration, 60 0C temperature, and 45 minutes of reaction time. Fuel properties were determined according to the ASTM defined methods and found within the defined limits of ASTM D-6751. 1H-NMR and 13C-NMR showed characteristic peaks at 3.667 ppm, 2.000 to 2.060 ppm, 0.858-0.918 ppm, 5.288-5.407 ppm, 24.93-34.22 ppm, 172.71, 173.12, 130.16 ppm, and 128.14 ppm, respectively, which confirm biodiesel synthesis. The FAMEs composition of biodiesel was determined by GC-MS which recognized 19 peaks for different types of FAMEs. FT-IR spectroscopy showed two main peaks, first in the range of 1725-1750 cm-1 and second in the range of 1000-1300 cm-1, which confirmed that the transesterification process was completed successfully. The physicochemical characteristics of Silybum marianum confirm that it is a suitable source to produce biodiesel on industrial scale.

Silver nanoparticles from Origanum vulgare (Oregano) have been synthesized in the past. However, no investigation has been performed on the combined effects of independent factors that affect the synthesis. Silver nitrate and Oregano concentrations, incubation temperature and time, as well as pH can play crucial roles in synthesis. In this regard Full Factorial Design was applied. A Voigt function was fitted on the measured UV – Vis spectra. The fitting parameters of the Voigt function (peak wavelength, area, and Full Width at Half Maximum) were used as the responses. A quadratic model was fitted for the peak wavelength and area, and the pH proved the dominant factor on nanoparticle synthesis.

With an increase in energy consumption globally, Fischer-Tropsch (FT) synthesis is a good alternative for producing fuels and chemicals from coal, natural gas or biomass. Among them, coal to liquids has been put into production in countries that have large coal reserves. In this process, Fe-based catalysts are commonly used due to their earth abundance, comparatively wide operation range and ready availability to handle low H2/CO ratio from coal. Despite their extensive applications, the kinetic and mechanistic understandings of Fe carburization and FT reaction on Fe-carbides are relatively limited due to the complexity of phase composition of the applied catalysts. This review summarizes the current state of knowledge of FT synthesis on Fe-carbide with an emphasis on underlying mechanism. Specifically, the employment of model catalyst, such as Raney-Fe, could provide a convenient way to furnish kinetic information regarding Fe carburization and subsequent FT reaction. A major challenge for further understanding catalytic reactions occurring at the Fe-carbide surface is correlating FT activity and selectivity to specific active site. To address this issue, the advancements of both DFT calculations and surface science techniques are highly demanded.

In this paper, the modification of two synthetic steps to obtain EMICORON, with respect to the usual protocol, is reported. EMICORON is a benzo[ghi]perylen-diimmide which was synthesized the first time in our laboratory in 2012 and showed to have in-vivo antitumor activities interfering with tumor growth and development by a multi-target mechanism of action. The provided modifications regarded the reaction times and the reaction conditions as well as the work-up procedures and allowed to increase the global yield of the process from 28% to about 40%. Thus, this new procedure may be more suitable in order to get larger amounts of EMICORON for further preclinical studies.

This paper aims to review the challenges, toxicity, and routes of synthesis and usage of silver nanoparticles in different applications but also highlighting their sustainability from both medical and environmental issues. Regarding their toxicity, it is known that silver nanoparticles can destroy over 650 microorganisms comparing with antibiotics. Supplementary, will be presented in a comparative manner some conventional synthesis routes (physical and chemical methods) and green synthesis routes using plant extracts. The approach using plant extracts have various advantages comparing with physical, chemical and microbial synthesis methods because there is no need to use chemicals, wasteful purifications and high energy requirements. The paper presents an overview on “green nanotechnology” focused on using either biological micro-organisms or plant extracts as an alternative to the classical chemical and physical methods. An important issue discussed in the paper is an overview of the synthesis routes of silver nanoparticles, some expected applications of silver based active agents and their toxicity and challenges that must be overcome. Also, it needs to focus our attention on the dismissal of silver nanoparticles into the environment and especially in water systems, fact which suggests that this issue must be fully understood and applied the law.

Compared with conventional semiconductors, halide perovskite nanocrystals (NCs) have a unique crystal structure and outstanding optoelectronic properties, which offer a wide potential for applications in optoelectronic devices such as solar cells, photodetectors, light emitting diodes, lasers and displays. Rational technological design is providing vital support for the development of perovskite optoelectronics. Herein, high-quality and monodisperse all-inorganic halide perovskite nanocrystals with consistent morphology, concentrated size distribution and cubic crystal phase were synthesized employing a modified one-pot hot injection method to independently modulate the stoichiometric ratios of three precursors involving cesium salt, lead source and halide. Mixing two kinds of perovskite NCs with different halogens, in combination with an anion exchange reaction, enables a transition from violet emission to green and finally to red emission over the entire visible region. Our work will be applied to enhance optoelectronic properties and stability of all-inorganic perovskite NCs for serving as light-emitting components in optoelectronic devices, as well as expanding the application areas of perovskite semiconductors for photocatalytic hydrogen generation, CO2 reduction and dye degradation.

Due to the linear property around an acetylenic carbon, the introduction of such an atom to a small cycle would result in high ring strain. Currently, the smallest isolated rings are five-membered, including metallacycloalkynes and metallapentalynes. Both types contain at least one unusual small bond angle around the acetylenic carbon, thus exhibiting abnormal reactivities. This feature article gives a comprehensive overview on these two kind complexes. The synthesis and reactivities are extensively described, the source of stability is presented, and the future prospect is discussed. The article aims to provide a better development for the chemical diversity of five-membered metallacycloalkynes and metallapentalynes.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

This review covers the last 25 years literature on analogs of suberoylanilide hydroxamic acid (SAHA, known also as Vorinostat) acting as HDAC inhibitor. In particular, the topic has been focused on the synthesis and biological activity of compounds where the phenyl group (the surface recognition moiety, CAP) of SAHA has been replaced by an azaheterocycle through a direct bond with amide nitrogen atom, and the methylene chain in the linker region is of variable length. Most of the compounds reported displayed good to excellent inhibitory activity against HDACs and in many cases showed anti-proliferative activity against human cancer cell lines.

Zn2GeO4 is considered a very promising alternative to current luminescent semiconductors. Previous results suggest that its emitted wavelength may depend on different variables, such as particle size and morphology, among others. In this work, we have prepared pure and highly homogeneous Zn2GeO4 nanorods under hydrothermal synthesis conditions with a willemite-like structure. Their luminescent properties have been explored and their band gap estimated, which are distinct to previously reported Zn2GeO4 bulk particles. Therefore, our results identify particle morphology as a crucial factor for maximizing and fine-tuning the luminesce of Zn2GeO4 nano-phosphors.

Herein we report on the use of different metal precursors in the synthesis of MoSe2 nanomaterials in order to control their morphology. The use of Mo(CO)6 as the metal precursor resulted in the formation of wrinkled few-layer nanosheets, while the use of H2MoO4 as the metal precursor resulted in the formation of nanoflowers. To investigate the effect of the morphologies on their performance as catalysts in the hydrogen evolution reaction, electrochemical characterization was done using linear sweep voltammetry, cyclic voltammetry and impedance spectroscopy. The MoSe2 nanomaterials were found to have superior electrochemical performance towards the hydrogen evolution reaction with a lower Tafel slope, on-set potential and potential at 10 mA/cm2 compared to the wrinkled few-layer nanosheets. This was found to be due to the higher effective electrochemical surface area of the nanoflowers compared to the nanosheets which suggests a higher number of exposed edge sites in the nanoflowers.

Some novel (phenyl-diazenyl)phenols (3a–g) were designed and synthesized to be evaluated for their antimicrobial activity. A previously synthesized molecule, active against bacteria and fungi, was used as lead for modifications and optimization of the structure, by introduction/removal or displacement of hydroxyl groups on the azobenzene rings. The aim of this work was to evaluate the consequent changes of the antimicrobial activity and to validate the hypothesis that, for these compounds, a plausible mechanism could involve an interaction with protein receptors, rather than an interaction with membrane. All newly synthesized compounds were analyzed by ¹H nuclear magnetic resonance (NMR), DSC thermal analysis and UV-Vis spectroscopy. The in vitro minimal inhibitory concentrations (MIC) of each compound was determined against Gram-positive and Gram-negative bacteria and Candida albicans. Compounds 3b and 3g showed the highest activity against S. aureus and C. albicans, with remarkable MIC values of 10 µg/mL and 3 µg/mL, respectively. Structure- activity relationship studies were capable to rationalize the effect of different substitutions on the phenyl ring of the azobenzene on antimicrobial activity.

This article presents the results of studies of the structure and conductive properties of Na3Fe2(PO4)3 polycrystals synthesized by solid-phase and melt (using concentrated optical radiation) methods. It has been established that with the melt method, the synthesis of the material occurs under significantly nonequilibrium temperature-gradient conditions, which leads to the creation of deformations in the sample that contribute to an increase in ionic conductivity. The ability of the Na3Fe2(PO4)3 structure to adapt to anomalous deformations that occur under temperature-gradient conditions indicates the elasticity of the crystalline framework {[Fe2(PO4)]3-}3∞. Through a comparative assessment of the structural parameters and conductive properties of these materials, it is shown that polycrystals obtained by the melt method have a better texture and greater ionic conductivity. The advantage of this method is that the duration of the synthesis of α-Na3Fe2(PO4)3 is halved. It is concluded that this method is applicable to obtain effective polycrystals of other compositions.

The accumulation of microorganisms, plants, algae, or small animals on wet surfaces that have a mechanical function causes biofouling, which can result in structural or other functional deficiencies. The maritime shipping industry must constantly manage biofouling to optimize operational performance, which is a common and long-lasting problem. It can occur in any metal structure in contact or submerged in ocean water, which represents additional costs in terms of repairs and maintenance. This study is focused on the production of antifouling coatings, made with nanoparticles of copper selenide (CuSe) modified with gum arabic, within a water-base acrylic polymeric matrix. During the curing of the acrylic resin, the CuSe NPs remain embedded in the resin but this does not prevent the release of ions. The coatings presented to release copper and selenium ions for up to 80 days, selenium was the element that was released the most. The adhesion of film coatings to metallic substrates showed good adhesion, scale 5B (ASTM D3359 standard). Antimicrobial activity tests show that the coatings have an inhibitory effect on Escherichia coli and Candida albicans. The effect being more noticeable when the coating is detached from the substrate and placed on a growing medium, than compared to the coating on a substrate. Scanning electron microscopy (SEM) observations show that nanostructured CuSe coatings are made up of rod-shaped and spherical particles whose range ranges from 12 to 25 nm. The Energy Dispersive X-ray spectroscopy (EDS) studies showed that the ratio of selenium nanoparticles is greater than that of copper and that their distribution is homogeneous

After Frankland first synthesized organotin compounds for the first time in 1849, their broad range of applications, including in industry and agriculture, resulted in a substantial increase in demand for organotin (IV) compounds after the 1940s. Because of the broad range of coordination numbers and molecular geometry that could result in numerous features, the structural diversity of organotin (IV) compounds is of great interest. Organotin (IV) dithiocarbamate has recently received attention as a therapeutic agent among organotin (IV) compounds. The hybrid complex individual properties of organotin (IV) and the dithiocarbamate moieties form a synergy of action stimulating increased biological activity. Organotin (IV) components have been shown in cytotoxicity studies to play a crucial role in cytotoxicity. Ligands serve to target and react to molecules while preventing unwanted changes in biomolecules. Organotin (IV) dithiocarbamate compounds have also been discovered to exhibit a broad range of cellular, biochemical, and molecular effects, with their toxicity largely determined by their structure. This review discusses the potential cytotoxicity effect of organotin(IV) dithiocarbamate, as well as its synthesis, elemental and spectroscopy analysis.

Leishmaniasis is a neglected tropical disease and affects more than 350 million people worldwide. However, there are no vaccines for humans, and current treatment is hampered due to its high cost, numerous side effects, and painful administration routes. Ending its epidemics by 2030 has become a United Nations goal, and the multitarget drug strategy emerges as a promising alternative. Flavonoids are an example of multitarget compounds and organic synthesis represents a tool to obtain high yields of these molecules. In our study, we synthesized 17 flavonoid analogs using a scalable, easy-to-reproduce, and inexpensive method. All compounds demonstrated an impressive inhibition capacity against rCPB2.8, rCPB3, and rH84Y, which are highly expressed in the amastigote stage, the target form of the parasite. Compounds 3c, f12a, and f12b stood out as effective against all isoforms and intermolecular interactions were investigated through a molecular modeling study. The compounds were highly potent against the parasite and demonstrated low cytotoxic action against mammalian cells. The results were pioneering, representing an advance in the investigation of the mechanisms behind the antileishmanial action of flavonoid derivatives. Furthermore, compounds have shown to be promising leads for the design of other cysteine protease inhibitors for the treatment of leishmaniasis diseases.

Lacunary polyoxometalates (POMs) are negatively charged metal−oxo clusters, formally obtained from plenary topologies via fragment removal. Owing to the fragment removal, the lacunary POMs archetypes are rich in nucleophilic terminal oxo ligands, making them suitable for post-synthetic coordination with various heterometals. Trilacunary heteropolytungstates (het-ero-POTs) based on bowl-shaped {W9O30} framework incorporating a central lone-pair containing {XO3} hetergroup (X = AsIII, SbIII, and BiIII) function as all-inorganic scaffolds that in the presence of d-block metal cations typically construct sandwich-like dimers of Hervé and/or Krebs. Herein we review the preparative approaches, compositional and magnetic versatility of the constructing Hervé and Krebs type dimers and discuss prospective use as POMtronics.

A model of the early RNA world is proposed. Nearly self-complementary sequences that could adopt double-stranded, smallhairpin-like (shRNA), structures would be selected for due to their greater hydrolytic stability. These would be phosphorylated attheir 5' ends. We suppose that dehydrating conditions arise (perhaps intermittently) in the early environment allowing amino acidsto condense with these RNA molecules. The resulting phosphate-amino acid anhydrides would play the role of early, charged,tRNAs. A crude genetic code could emerge owing to the greater resistance of some amino acid-shRNA pairings to hydrolysisrelative to others. Early on there is no division of labor between mRNAs and tRNAs; the same molecules perform both functions.But the first systems would have encoded little in the way of protein sequence information. Rather they would have served as catalysts for the random polymerization of amino acids. It is speculated that the selective advantage inhering in such systems lay intheir ability to supply raw materials for the formation of coacervates within which the various molecules essential to proto-lifecould be concentrated. This would greatly facilitate the necessary chemistries. The evolution of homochiral protein and RNA populations is discussed. An appealing feature of this model is its ability to explain the transition from phosphorylated amino acids to the 3' ester-linked aminoacyl-tRNAs employed by modern life.

This study was conducted to investigate the effect of supplementing different types of methionine (L and D-type) and its precursor (HMBi) on milk protein synthesis using immortalized bovine mammary epithelial cell line (MAC-T Cell); D-methionine (D-Met), L-methionine (L-met) and 2-hydroxy-4-methylthiobutanoic acid I (HMBi), an isopropyl ester of the hydroxy analogue precursor of methionine. The underlying mechanism of milk protein synthesis by adding D- and L-type amino acid as well as HMBi was elucidated through omics analysis to verify the metabolism pathway. Results showed that HMBi group showed the highest beta casein mRNA expression levels compared to D- and L-Met groups and highest medium protein although not different with the L-Met treatment. The observed upregulated (>2 protein expression vs. control) and downregulated (<0.5 protein expression vs. control) proteins in L-Met, D-Met and HMBi treated groups were: 39, 77; 46, 68; and 40, 78, respectively. Interestingly, based on protein pathway analysis, L-Met treated group stimulated the ATP synthesis, PI3 kinase and pyruvate metabolism. On the other hand, the D-Met group stimulated fructose-galactose metabolism, glycolysis pathway, PI3 kinase and pyruvate metabolism. And lastly HMBi-treated group stimulated pentose phosphate pathway and glycolysis pathway. Metabolite analysis revealed that L-Met treated group resulted in the increase in 11 metabolites. On the other hand, D-Met treated group showed increase in 7 metabolites and decreased of uridine monophosphate (UMP). HMBi supplementation caused increases of 3 metabolites and decreased of UMP and N-acetyl-L-glutamate Addition of different isoforms of Met stimulated the production of intermediate metabolites for energy production. Addition of L-Met stimulated the production of energy metabolites such as pyruvate, malate, and fumarate, well-known as intermediates of Krebs cycle. On the other hand, HMBi supplementation resulted in increases of energy metabolite glucose 1-phosphate and 6-phosphogluconate. Results showed that HMBi-treated group exhibited highest expression of β-casein mRNA expression by stimulating proteins and metabolites as well as protein and metabolic pathways involved in protein and energy synthesis. As a result, HMBi-treated group resulted in highest protein concentration but not significantly different with L-Met. Both the D- and L-isoforms has considerably the same medium protein concentration and β-casein mRNA expression higher than the control. So, D- and L-Met isoforms can be used alternatively without any significant change in protein synthesis efficiency in bovine mammary epithelial cells.

Chitosan treatment results in significantly lower serum LDL cholesterol concentrations. To assess the working mechanism of chitosan, we measured serum surrogate markers of cholesterol absorption (campesterol, sitosterol, cholestanol), synthesis (lathosterol, lanosterol, desmosterol), and degradation to bile acids (7α-hydroxy-cholesterol, 27-hydroxy-cholesterol) corrected for cholesterol concentration (R_sterols). Over 12 weeks, 116 obese subjects (BMI 31.7, range 28.1 – 38.9 kg/m²) were studied under chitosan (n=61) and placebo treatment (n=55). The participants were briefly educated regarding improvement of nutrition quality and energy expenditure. Daily chitosan intake was 3200 mg. Serum LDL cholesterol concentration decreased significantly more (P=0.0252) under chitosan (-8.67 ± 18.18 mg/dl, 5.6%) than under placebo treatment (-1.00 ± 24.22 mg/dl, 0.9%). This reduction was not associated with the expected greater decreases in markers of cholesterol absorption under chitosan treatment. Also, increase in markers of cholesterol synthesis and bile acid synthesis under chitosan treatment was not any greater than under placebo treatment. In conclusion, a significant selective reduction of serum LDL cholesterol under chitosan treatment is neither associated with a reduction of serum surrogate markers of cholesterol absorption nor with an increases of markers for cholesterol and bile acid synthesis.

Quarry waste fines and eggshells are unavoidable wastes which relentlessly contribute to environmental load and pollution. Although a number of studies have suggested various methods for recycling, these wastes remain underutilized due to some technical constraints. In addition, no study has yet been explored on the possibility of combining quarry waste fines (QWF) and eggshell powder (ESP) for tobermorite synthesis. Tobermorite is the main component which primarily provides strength to the autoclaved aerated concrete products. For this purpose, this study seeks to evaluate the potential of QWF- ESP mix at 10%, 15% and 20% amounts of cement, respectively. The XRF, XRD, and TGA–DTA techniques were used to characterize the waste materials while physical and mechanical property tests and XRD analysis were performed on the autoclaved samples. It was found that QWF contains 53.77% SiO2, while ESP contains 97.8% CaO which are key components for tobermorite synthesis. This study also revealed that the mixture with only 10% cement has the highest compressive strength among the QWF-ESP samples. Furthermore, the formation of tobermorite in the samples was confirmed through XRD analysis. Hence, the hydrothermal curing of QWF –ESP can be further developed to produce functional tobermorite – bearing materials.

Voice cloning, an emerging field in the speech processing area, aims to generate synthetic utterances that closely resemble the voices of specific individuals. In this study, we investigate the impact of various techniques on improving the quality of voice cloning, specifically focusing on a low-quality dataset. To contrast our findings, we also use two high-quality corpora for comparative analysis. We conduct exhaustive evaluations of the quality of the gathered corpora in order to select the most suitable audios for the training of a Voice Cloning system. Following these measurements, we conduct a series of ablations by removing audios with lower SNR and higher variability in utterance speed from the corpora in order to decrease their heterogeneity. Furthermore, we introduce a novel algorithm that calculates the fraction of aligned input characters by exploiting the attention matrix of the Tacotron 2 Text-to-Speech (TTS) system. This algorithm provides a valuable metric for evaluating the alignment quality during the voice cloning process. We present the results of our experiments, demonstrating that the performed ablations significantly increase the quality of synthesised audios for the challenging low-quality corpus. Notably, our findings indicate that models trained on a 3-hour corpus from a pre-trained model exhibit comparable audio quality to models trained from scratch using significantly larger amounts of data.

The gold nanoparticle (AuNP) was synthesized using the well-known Turkevich method. This article explains didactic step-by-step of the synthesis, showing pictures of the entire process, including a well-explained mechanism and characterization study. The synthesis includes the reduction of NaAuCl4 using sodium citrate in high temperature (around 90 ⁰C). The two main mechanisms used to explain the AuNP synthesis via Turkevich method were explained. The first mechanism considerate that a nanowire intermediary and the other proposed that aggregate intermediates are not formed at any time during the synthesis. The materials (NaAuCl4 and AuNP) were characterized by UV-Vis, SEM, AFM, XRD and DLS. The UV-Vis exhibit an absorption maximum in 521 nm because the surface plasmon resonance (SPR) absorption band of AuNP. The SEM images of NaAuCl4 presents crystals with cubic shapes, while the AuNP presents average particle size of about 16-25 nm and particles that appear mainly spherical. To confirm the particles shapes, the AFM was conducted and it was possible to observe clearly the individual spherical nanoparticles. The XRD of AuNP showed the four main characteristic peaks for silver corresponding to (111), (200), (220) and (311) planes, confirming the cubic (FCC) silver. The DLS presented the average particle size of 3.3 ± 0.9 nm and the polydispersity index (PDI) of 0.574. In summary, the AuNP was synthesized using a simple and fast method. The result was a spherical and ultrasmall particle, that can be used is several applications.

The first diastereoselective synthesis of (–)-1-epi-lentiginosine stars from a common chiral trans-epoxyamide derived from 2-pyridincarbaldehyde is reported. This methodology involves a sequential oxirane ring opening and intramolecular 5-exo-tet cyclization of tosylate tras-epoxyalcohol to afford a diastereomeric mixture of indolizinium salts in a one-pot fashion, followed by regio- and diastereospecific pyridinium ring reduction.

Conclusive evidence that specic long-term memory formation relies on den- dritic growth and structural synaptic changes has proven elusive. Connec- tionist models of memory based on this hypothesis are confronted with the so-called plasticity stability dilemma or catastrophic interference. Other fun- damental limitations of these models are the feature binding problem, the speed of learning, the capacity of the memory, the localisation in time of an event and the problem of spatio-temporal pattern generation. This paper suggests that the generalisation and long-term memory mechanisms are not correlated. Only the development and the improvement of the feature ex- tractors in the cortex involves structural synaptic changes. We suggest the long-term memory has a separate mechanism which involves protein synthe- sis to encode the information into the structure of these proteins. A model of memory should be capable of explaining the dierence between memorisation and learning. Learning has in our approach two dierent mechanisms. The generalisation in the brain is handled by the proper development of the links between neurons via synapses. The Hebbian learning rule could be applied only for this part of learning. Storing an internal ring pattern involves, in our approach, a new mechanism which puts the information regarding this ring pattern into the structure of special proteins in such a way that it can be retrieved later. The hypotheses introduced in this article includes a physiological assumption which has not been yet verified because it is not currently experimentally accessible. Keywords: Waves, Protein Synthesis, Resonance, Long Term Memory Preprint submitted to Neural Networks

Lemonomycin (1) was first isolated from the fermentation broth of Streptomyces candidus in 1964. The complete chemical structure was not elucidated until 2000 with extensive spectroscopic analysis. Lemonomycin is currently known as the only glycosylated tetrahydroisoquinoline antibiotic. Its potent antibacterial activity against Staphylococcus aureus and Bacillus subtilis and complex architecture make it an ideal target for total synthesis. In this short review, we summarize the research status of lemonomycin for biological activity, biosynthesis and chemical synthesis. The unique deoxy aminosugar-lemonose was proposed to play a crucial role in biological activity, as shown in other antibiotics, such as arimetamycin A, nocathiacin I, glycothiohexide α, and thiazamycins. Given the self-resistance of the original bacterial host, the integration of biosynthesis and chemical synthesis to pursue efficient synthesis and further derivatization is in high demand for the development of novel antibiotics to combat antibiotic-resistant infections.

One of the areas of research on materials for thin-film solar cells focuses on replacing In and Ga with more earth-abundant elements. In that respect, chalcostibite (CuSbS2) is being considered as a promising environmentally friendly and cost-effective photovoltaic absorber material. In the present work, single CuSbS2 phase have been synthesized directly by a short duration (2 h) mechanochemical synthesis step starting from mixtures of elemental powders. X-ray diffraction analysis of the synthesized CuSbS2 powders revealed a good agreement with the orthorhombic chalcostibite phase, space group Pnma, and a crystallite size of 26 nm. Particle size characterization revealed a multimodal distribution with a median diameter ranging from of 2.93 m to 3.10 m. The thermal stability of the synthesized CuSbS2 powders was evaluated by differential thermal analysis. No phase change was observed by heat treating the mechanochemically synthesized powders at 350 C for 24 h. By UV-VIS-NIR spectroscopy the optical bandgap was determined to be 1.41 eV, suggesting that the mechanochemically synthesized CuSbS2 can be considered suitable to be used as absorber materials. Overall, the results show that the mechanochemical process is a viable route for the synthesis of materials for photovoltaic applications.

A technology for obtaining nanosized aluminum nitride powder by plasma-chemical synthesis is presented. Nitrogen gas (N2), melamine (C3H6N6) and ammonia (NH3) were used as a source of nitrogen. Aluminum powder of different fractions was used as a source of aluminum. The influence of the nitrogen source, the height of the injector, and the input power of the plasma equipment on the synthesized aluminum nitride powder is shown. The resulting aluminum nitride powder has a size d90=60 nm. The parameters of aluminum nitride synthesis did not in any way affect the granulometric composition of the synthesized powder materials. It was found that, due to the high binding energy, the nitrogen molecule (N2) reacts poorly with aluminum powder particles, as a result a mixture of nitrogen and ammonia gases was used in a ratio of 70/30 (mol.%) for aluminum nitride synthesis.

Viral infections inflict many serious human diseases, being responsible for remarkably high mortality rates. In this sense, both the academy and the pharmaceutical industry are continuously searching for new compounds with antiviral activity, and in addition, face the challenge of developing greener and more efficient methods to synthesize these compounds. This becomes even more important with drugs possessing stereogenic centers as highly enantioselective processes are required. In this minireview, the advances achieved to improve synthetic routes efficiency and sustainability of important commercially antiviral chiral drugs are discussed, highlighting the use of organocatalytic methods.

The hydrothermal synthesis of aluminophosphate molecular sieve type AlPO4-11 was processed from chemicals containing psueudobohemite, 85% phosphoric acid, water, and di-isopropylamine as templating agent. The crystallization of the samples was studied by taking samples in times from 2 to 74 hours. The obtained white powder products have been characterized by XRD patterns, FT-IR spectra, thermogravimetric data, scanning electron microscopy and pH measurement of the mother liquor. The pore volume, as determined from TG and DTG curves, was ca. 0.17 cm3g-1. The crystallization process of the aluminophosphate exhibited in its initial phase a behavior of first order reaction with a specific velocity constant of ca. 0.25 h-1, as determined from XRD and FT-IR data.

Abstract:The Schiff bases obtained from formylmenthone and o-, m-, p-toluidine behave as bidentate ligands with O and N donor atoms in Ni(ll) and Cu(II) complexes by the type NiL2 and CuL2.(H2O)2. The donor atoms and the possible geometry for the complexes were assigned by means of chemical, thermodifferential analyses and electronic, EPR and IR spectra.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

Clay minerals surfaces potentially played a role in prebiotic synthesis through adsorption of organic monomers that give rise to highly concentrated systems; facilitate condensation and polymerization reactions; protection of early biomolecules from hydrolysis and photolysis; and surface-templating for specific adsorption and synthesis of organic molecules. This review presents processes of clay formation using saponite as a model clay mineral since it is shown to catalyze organic reactions, easy to synthesize in large and pure form, and has tunable properties. In particular, a method involving urea is presented as a reasonable analog of natural processes. The method involves a two-step process – 1) formation of the precursor aluminosilicate gel and 2) hydrolysis of a divalent metal (Mg, Ni, Co, Zn) by the slow release of ammonia from urea decomposition. The aluminosilicate gels in the first step forms a 4-fold-coordinated Al³⁺ similar to what is found in nature such as in volcanic glass. The use of urea, a compound figuring in many prebiotic model reactions, circumvents the formation of undesirable brucite, Mg(OH)₂, in the final product by slowly releasing ammonia thereby controlling the hydrolysis of magnesium. In addition, the substitution of B and Ga for Si and Al in saponite is also described The saponite products from this urea-assisted synthesis were tested as catalysts for several organic reactions including Friedel-Crafts alkylation, cracking and isomerization reactions.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

In this paper, the design and analysis of coupled tank water level control system is done using robust control theory. The main aim of this work is to improve level controlling mechanisms in industries and household areas. In this paper, H ∞ and μ –synthesis controllers are designed to improve the level control system. The coupled tank water level control system is designed using the proposed controller’s comparison and tested for tracking a reference level signals (step, sine wave and random) and simulation results have been analyzed successfully. Finally the comparative simulation results prove the effectiveness of the proposed coupled tank water level control system with H ∞ controller for improving the tracking mechanism performance of the system.

(-)-Zeylenone is a promising cytotoxic agent，which is a natural product isolated from Uvaria grandiflora Roxb. Though substantial antitumor mechanism has been researched , little has focused on its enantiomer (+)-Zeylenone.This article will try to find a gram scale synthesis method of (+)-Zeylenone and explain the structure-activity relationship of this kind of compound. Total synthesis of (+)-zeylenone was completed in 13 steps with quinic acid as starting material in 8.8% overall yield. The highlight of the route was the control of the three carbon’s chirality by clever use of single step dihydroxylation under the direction of the key C-3 chirality. In addition, zeylenone derivatives were designed and synthesized and their antitumor activity were evaluated against three human cancer cell lines using the CCK8 assay. Structure-activity relationship suggested compounds with both two absolute configurations exhibited good activity. Besides, hydroxyls at C-1/2 position were crucial for the activity and esterification of C-1 hydroxyl with large groups made the activity disappeared. Hydroxyl at C-3 position was also important as proper ester substituent could increase the potency.

The study was done to determine the effect of supplementing different forms of L-methionine (L-Met) and acetate on protein synthesis in immortalized bovine mammary epithelial cell line (MAC-T Cell): Control, L-Met, conjugated L-Met and acetate (CMA), and non-conjugated L-Met and Acetate (NMA). Protein synthesis mechanism was determined by omics method. NMA group had the highest protein content in the media and β-casein mRNA expression levels (P < 0.05). The number of upregulated and downregulated proteins observed were 77 and 62 in CMA group and 50 and 81 in NMA group from 448 proteins, respectively (P < 0.05). NMA and CMA treatments stimulated pathways related to protein and energy metabolism (P < 0.05). Metabolomic analysis also revealed CMA and NMA treatments resulted in increases of several metabolites (P < 0.05). In conclusion, NMA treatment increased protein concentration and expression level of β-casein mRNA in MAC-T cells compared to CMA.

Background. Nanotechnology is promising field for generating new applications. A green synthesis of nanoparticles through biological methods using plant extract have a reliable and ecofriendly approach to improve our global environment. Methods. Silver nanoparticles (AgNPs) were synthesized using aqueous extract of Anagalis arvensis L and silver nitrate and were physicochemically characterized. Results. The stability of AgNPs toward acidity, alkalinity, salinity and temperature showed that they remained stable at room temperature for more than two months. The SEM and TEM analysis of the AgNPs showed that they have a uniform spherical shape with an average size in the range of 40–78 nm. Further 1-Dibhenyl-2-Picrylhydrazl radical in Anagalis arvensis L.mediated AgNPs showed a maximum activity of 98% at concentration of 200μg/mL. Hydrogen peroxide scavenging assay in Anagalis arvensis L. mediated AgNPs showed a maximum activity of 85% at concentration of 200μg/mL. Reducing power of Anagalis arvensis L.Ag NPs exhibited a higher activity of 330 μg/mL at concentration of 200 μg/mL. These NPs have cytotoxic effects against brine shrimp (Artemia salina) nauplii with a value of 53% LD 178.04μg/mL. Conclusion. The AgNPs synthesized using Anagalis arvensis L. extract demonstrate a broad range of applications.

In this study, an improved UPLC-MS method for simultaneously quantifying twelve major components belonging to two chemical types was developed and validated, and was applied to quantitatively compare the quality of Astragali Radix sulfur-fumigated with different durations and the fresh reference sample. The results showed that the contents of triterpenes Astragaloside III and Astragaloside IV decreased moderately, while the flavonoids calycosin, formononetin, and 7,2'-dihydroxy-3',4'-dimethoxyisoflavane decreased significantly, and its corresponding flavonoid glycosides increased accordingly, which indicatied that the happening of chemical transformation of flavonoids and glycosides in the sulfur-fumigated process. These transformations were further confirmed by the the synthesis of flavonoid glycosides under the simulated sulphur-fumigation circumstances. Furthermore, the sulfur-fumigated duration had a proportional relationship with the contents of compounds 7, 11, and 12. All these results suggested that the established method was precise, accurate and sensitive enough for the global quality evaluation of sulfur-fumigated Astragali Radix, and sulfur-fumigation can not only change the proportions of bioactive components, but also cause the chemical transformation in the Astragali Radix.

Conversational spoken dialogue systems that interact with the user rather than merely reading text can be equipped with hesitations to manage the dialogue flow and the users' attention. Based on a series of empirical studies, we built an elaborated hesitation synthesis strategy for dialogue systems that inserts hesitations of scalable extent wherever needed in the ongoing utterance. So far, evaluations of hesitating systems have shown that synthesis quality is affected negatively by hesitations, but that there is improvement in interaction quality. We argue that due to its conversational nature, hesitation synthesis needs interactive evaluation rather than traditional MOS-based questionnaires. To prove this point, we dually evaluate our system’s speech synthesis component: on the one hand, linked to the dialogue system evaluation, on the other hand, in the traditional MOS way. This way we are able to analyze and discuss differences that arise due to the evaluation methodology. Our results suggest that MOS scales are not sufficient to assess speech synthesis quality, which has implications for future research that are discussed in this paper. Furthermore, our results indicate that hesitations work well to increase task performance and that an elaborated strategy is necessary to avoid likability issues.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

Boron carbide (B4C) powders with defined stoichiometry, high crystallinity, minimal impurity content, and a fine particle size are imperative for realizing the exceptional properties of this compound in advanced high-technology applications. Nevertheless, achieving the desired stoi-chiometry and particle size using traditional synthesis methods, which rely on prolonged, high-temperature processes, can be challenging. The primary objective of this study is to syn-thesize fine B4C powders characterized by high crystallinity and a sub-micron particle size, em-ploying a fast, and energy-efficient method. B4C powders are synthesized from elemental boron and carbon in a high-frequency induction heating furnace using the Electromagnetic Induction Synthesis (EMIS) method. The rapid heating rate achieved through contactless heating promotes the ignition and propagation of the exothermic chemical reaction between boron and carbon. Additionally, electromagnetic effects accelerate atomic diffusion, allowing the reaction to be completed in an exceptionally short timeframe. The grain size and crystallinity of B4C can be finely tuned by adjusting various process parameters, including the post-ignition holding temperature and the duration of heating. As a result, fine B4C powders can be synthesized in under 10 minutes. Moreover, these synthesized B4C powders exhibit high resistance to oxidation when exposed to air.

We have recently reported that a series of 1,3,4-oxadiazol-2-ylbenzenesulfonamides acts as potent and specific monoamine oxidase B (MAO-B) inhibitors with some compounds possessing potencies in the nanomolar range. While sulfonamide compounds (e.g., zonisamide) have been reported to inhibit the MAO enzymes, nanomolar MAO inhibition potencies for this class are not frequently observed. The present study expanded on these findings by replacing the 1,3,4-oxazole moiety with a 1,3-thiazole heterocycle. A series of 23 primary sulfonamides were synthesized by reaction of an α-haloketone with a substituted carbothioamide. The results of the MAO inhibition studies showed that the 1,3-thiazolylbenzenesulfonamides were specific inhibitors of human MAO-B. The most potent MAO-B inhibitor exhibited an in vitro IC50 value of 0.103 µM (3j). The derivatives were, however, weaker inhibitors of human MAO-A with the most potent compound exhibiting an IC50 value of 11.9 µM (3a). Examination of the structure-activity relationships (SARs) showed that the most potent MAO-B inhibition was obtained with substitution of the sulfonamide on the meta position of the phenyl rather than the para position. This study concludes that 1,3-thiazolylbenzenesulfonamides represent a class of potent and specific MAO-B inhibitors, which may serve as leads for the development of new treatments for disease states such as Parkinson’s disease.

Researchers are increasingly focusing on green synthesis methods for silver nanoparticles due to their cost-effectiveness and reduced environmental impact. In this study, we utilized an edible bird's nest (EBN), a valuable economic resource, as the primary material for synthesizing silver nanoparticles using only water as the solvent. Metabolite profiling of the EBN extract was conducted using LC-QTOF-MS in positive mode (ESI+), revealing the presence of lipids, glycosides, peptides, polysaccharides, and disaccharides. Upon the addition of silver nitrate to the aqueous EBN extract, noticeable color changes from transparent to brown indicated the successful formation of AgNPs. Subsequent characterization of these silver nanoparticles involved UV-Visible spectroscopy, which revealed an absorption peak at 421 nm. Further characterization was carried out using Field Effect Scanning Electron Microscopy (FESEM), Attenuated Total Reflectance-Fourier Infrared (ATR-FTIR) spectroscopy, and Energy Dispersive X-Ray (EDX) analysis. The involvement of phenolic agents, proteins, and amino acids in reducing the silver particles was confirmed. The synthesized nanoparticles exhibited a crystalline nature, a spherical shape, and a particle size ranging from 10 to 20 nm. The presence of elemental silver was confirmed by a strong, intense peak around 3 keV in the EDX spectrum. To assess their potential, the antibacterial properties of the silver nanoparticles against Escherichia coli and Staphylococcus aureus were evaluated using the agar diffusion method.

Most existing data synthesis methods are designed to tackle problems such as dataset imbalance, data anonymization and insufficient sample size. There is a lack of effective synthesis methods for the limited number of datasets which contain a large of features and unknown noise to expand the size of the dataset. We propose a data synthesis method, named Adaptive Subspace Interpolation for Sample Optimization (ASISO). The idea is to divide the original feature space into several subspaces with an equal number of samples, and then perform interpolation for the samples in the adjacent subspaces. This method can adaptively adjust the size of the dataset containing unknown noise, and the expanded data typically contain minimal error with actual. Moreover, it adjusts the structure of the samples, which can significantly reduce the proportion of samples with large errors. In addition, the hyperparameters of this method have an intuitive explanation and usually require little calibration. Experimental results on artificial data and benchmark data sets demonstrate that ASISO is a robust and stable method to optimize samples.

Methodologies for the synthesis and purification of metabolites, which have been developed following their discovery, analysis and structural identification, have been involved in numerous life science milestones. The renewed focus on the small molecule domain of biological cells has also created an increasing awareness of the rising gap between the metabolites identified and the metabolites which have been prepared as pure compounds. Due to the large number and molecular diversity of metabolites the design and engineering of resource-efficient and straightforward synthetic methodologies for their production have attracted much interest. The variety of metabolic pathways in biological cells provide a wonderful blueprint for designing simplified and resource-efficient synthetic routes to desired metabolites. Therefore, biocatalytic systems have become key enabling tools for the synthesis of an increasing number of metabolites, which can then be utilized as standards, enzyme substrates, inhibitors or products, or for the discovery of novel biological functions.

Aromatic azo compounds have -N=N- double bonds as well as larger π electron conjugation system, which endows aromatic azo compounds with wide applications in the fields of functional materials. The properties of aromatic azo compounds are closely related to the substituents on their aromatic rings. However, traditional synthesis methods, such as the coupling of diazo salts, have a great limitation on the structural design of aromatic azo compounds. Therefore, many scientists have devoted their efforts to developing new synthetic methods. Moreover, recent advances in the synthesis of aromatic azo compounds led to the improvement of design and preparation of light-response materials at molecular level. This review summarizes the important synthetic progress of aromatic azo compounds in recent years, with an emphasis on the pioneering contribution of functional nanomaterials in the field.

Novel tetragonal matrix Ba0.5Gd0.5-xNaxF2.5-x, where x = 0.05, doped by Yb3+, Ho3+, Er3+, was synthesized by molten salt synthesis (MSS) from nitrate flux. XRD data show that tetragonal phase with a = 4.122(1) Å, c = 17.672(1) Å is stable in argon atmosphere up to 960 °C. Luminescence spectra recorded in 500-900 nm and 1050-1700 nm upon 974 nm pumping demonstrated the characteristic luminescence at 1550 nm (4I13/2 → 4I15/2) for Er3+ and 1150 nm (5I6 → 5I8) for Ho3+. The relative thermal sensitivity (Sr) at 296-316 K were 0.3 %*K-1 and 5.5%*К-1 in shortwave infrared (SWIR) and visible range, respectively. Synthesized luminophores can be used as dual-range optical temperature sensors, which simultaneously operating in visible and SWIR ranges.

Scutellaria multicaulis, a member of the Lamiaceae, is a medicinal plant indigenous to Iran, Afghanistan, and Pakistan. It has been widely used as a prominent herb in traditional medicine for thousands of years. This plant is reported with baicalein, wogonin, and chrysin flavonoids as a significant group of chemical ingredients, which can cure different diseases such as breast cancer. S. multicaulis leave extract was used for the bioreduction of silver nanoparticles (SmL-Ag-NPs), and their phytochemical contents and antioxidant, antibacterial, anti-proliferative, and apoptotic activity were evaluated. Optimal physicochemical properties of SmL-Ag-NPs were obtained by mixing 5% of leave extract and 2 mM of aqueous AgNO3 solution and confirmed by characterization studies including UV–visible spectrophotometry, FE-SEM, EDX, DLS, zeta potential, TGA, SERS, XRD and FTIR Spectroscopy. SmL-Ag-NPs exhibited higher content of TPC (Total Phenolic Content) and TFC (Total Flavonoid Content) and potential antioxidant activity. SmL-Ag-NPs also demonstrated dose-dependent cytotoxicity against MDA-MB231 cells multiplication with an IC50 value of 37.62 μg/mL at 48h through inducing cell apoptosis. This is the first report on the biosynthesis of silver nanoparticles using S. multicaulis leave extract, which can provide treatment for cancer diseases and reduce some negative effects of chemotherapy.

Modern medical needs call for the efficient remedies against bacterial diseases including severe pulmonary infections reported as a secondary SARS-Cov-2 infection. Here, we propose imprinted drug ciprofloxacin (CF) into the polymer based on methyl-β-cyclodextrin (MCD) via template synthesis. The obtained polycarbamide nanoparticles possess CF's sustained drug release. The interaction of human serum albumin (HSA) with CF and CF-MCD carriers was conducted by FRET, FTIR, fluorescence, and circular dichroism spectroscopy. These studies uncovered that MCD decreases CF's binding efficiency by 2 times, whereas CF’s encapsulation in polymer matrix doubles the Ka value. The changes in HSA’s secondary structure indicate no alterations in the main mechanism of complex formation between CF and HSA in the presence of MCD-based carries. The drug delivery system demonstrates prolonged CF release at pH 7.4 in presence of HSA (model conditions of blood plasma). CF-MCD carriers inhibit E. coli and B. subtilis growth, but for MAX systems we observed a MIC’s increase (~2 times). We believe that our findings are important for further development of new efficient drug forms.

This review uses the National Cancer Institute (NCI) COMPARE program to establish an extensive list of heterocyclic iminoquinones and quinones with similarities in differential growth inhibition across the 60-cell line panel of the NCI Developmental Therapeutic Program (DTP). Many natural products and synthetic analogues are revealed, as potential NAD(P)H:quinone oxidoreductase 1 (NQO1) substrates through correlations to dipyridoimidazo[5,4-f]benzimidazoleiminoquinone (DPIQ), and as potential thioredoxin reductase (TrxR) inhibitors, through correlations to benzo[1,2,4]triazin-7-ones and pleurotin. The strong correlation to NQO1 infers the enzyme has a major influence on the amount of active compound with benzo[e]perimidines, phenoxazinones, benz[f]pyrido[1,2-a]indole-6,11-quinones, seriniquinones, kalasinamide, indolequinones, and furano[2,3-b]naphthoquinones, hypothesized as prodrugs. Compounds with very strong correlations to known TrxR inhibitors had inverse correlations to the expression of both reductase enzymes, NQO1 and TrxR, including naphtho[2,3-b][1,4]oxazepane-6,11-diones, benzo[a]carbazole-1,4-diones, pyranonaphthoquinones (including kalafungin, nanomycin A, and analogues of griseusin A), and discorhabdin C. Quinoline-5,8-dione scaffolds based on streptonigrin and lavendamycin can correlate to either reductase. Inhibitors of TrxR are not necessarily (imino)quinones, e.g., parthenolides, while oxidizing moieties are essential for correlations to NQO1, as with the mitosenes. Herein, an overview of synthetic methods and biological activity of each family of heterocyclic imino(quinone) is provided.

Multicomponent reactions (MCRs) have been used for more than a century; since their discovery in 1850 by Strecker. To date, MCRs route is regarded as a beneficial strategy due to its capacity to quickly produce molecular diversity and structural complexity of interest for a variety of applications. Despite having famous MRCs such as the Ugi, Passerini, Biginelli, and Hantzsch, this re-view portrays the importance of MCRs in the synthesis of desired products towards applications such as medicinal purposes, sustainable chemistry, and polymerisation. MCRs provide ad-vantages such as reducing the number of sequential multiple reactions to one step, atom economy, recyclable catalysts, mild conditions, preventing waste and reduce solvent use.

This work aimed to study the thermal and crystalline properties of poly (1,4-phenylene sulfide)@carbon char nanocomposites. Coagulation-processed nanocomposites of polyphenylene sulfide were prepared using synthesized mesoporous nanocarbon of coconut shell as reinforcement. The mesoporous reinforcement was synthesized using a facile carbonization method. The investigation of the properties of nanocarbon was done by SAP, XRD, and FESEM analysis. The research was further propagated via the synthesis of nanocomposite by the addition of characterized nanofiller into poly (1,4-phenylene sulfide) at five different combinations. The coagulation method was utilized for the nanocomposite formation. The obtained nanocomposite was analyzed using FTIR, TGA, DSC, and FESEM analysis. The BET surface area and average pore volume of bio-carbon prepared from coconut shell residue were calculated to be 1517 m2/g and 2.51 nm respectively. The addition of nanocarbon to poly (1,4-phenylene sulfide) has led to an increase in thermal stability and crystallinity up to 6% loading of filler. The minimum achievable glass transition temperature is for 6 % doping of filler into the polymer matrix. It was established that the thermal, morphological, and crystalline properties have been tailored by synthesizing their nanocomposites with mesoporous bio-nanocarbon obtained from coconut shells. So, the loading of filler into poly (1,4-phenylene sulfide) can be optimized to enhance its thermoplastic properties for surface applications.

Diamond powders with inclusions of europium atoms were synthesized at high pressure (7.7 GPa) and temperature (1800oC) from a mixture of pentaerythritol, C(CH2OH)4, and pyrolyzate of diphthalocyanine (C64H32N16Eu) served as a special precursor. In prepared diamonds by X-ray fluorescence spectroscopy, we have found the concentration of Eu atoms of 51±5 ppm that is by two orders of magnitude greater than that in known natural and synthetic diamonds. X-ray diffraction, SEM, X-ray exited optical luminescence, Raman and IR spectroscopy have confirmed the formation of diamond monocrystals of high quality with em-bedded Eu atoms and a nitrogen content of ~500 ppm. Numerical simulation has allowed us de-termine the energy cost of 5.8 eV needed for the incorporation of a single Eu atom with adjacent vacancy into growing diamond crystal (528 carbons).

Cancer therapy resistance is a persistent clinical challenge. Recently, inhibition of the mutagenic translesion synthesis (TLS) protein REV1 was shown to enhance tumor cell response to chemotherapy by triggering senescence hallmarks. These observations suggest REV1’s important role in determining cancer cell response to chemotherapy. Whether REV1 inhibition would similarly sensitize cancer cells to radiation treatment is unknown. This study reports a lack of radiosensitization in response to REV1 inhibition by small molecule inhibitors in ionizing radiation-exposed cancer cells. Instead, REV1 inhibition unexpectedly triggers autophagy, which is a known biomarker of radioresistance. Collectively, we report a possible role of REV1 TLS protein in determining cancer treatment outcomes depending upon the type of DNA damage inflicted. Furthermore, we discover REV1 inhibition directly triggers autophagy, an uncharacterized REV1 phenotype, with significant bearing on cancer treatment regimens.

Cutting-edge technologies are intensifying into new skylines and this remarkable progress has been successfully influenced by the tiny level engineering of carbon dots technology, their syn-thesis advancement and impressive applications in the field of allied sciences. The advances of science and its conjugation with interdisciplinary fields emerged in carbon dots making, their controlled characterization and applications into faster, cheaper as well as more reliable prod-ucts in various scientific domains. Thus, a new era in nanotechnology has developed into carbon dots technology. The understanding of the generation process, control on making processes and selected applications of carbon dots such as energy storage, environmental monitoring, catalysis, contaminates detections and complex environmental forensics, drug delivery, drug targeting and other biomedical applications etc. are among the most promising applications of carbon dots and thus a thrust area of research today. In this regard, various types of carbon dots nano-materials such as oxides, their composites and conjugations etc. have been flocking significant attention due to their remarkable potential in this thrust area of energy, the environment and technology. Thus, the present paper highlights the role and importance of carbon dots, recent advancements in their synthesis methods, properties and emerging applications.

Pretreatment with non-convulsive dose of methionine sulfoximine (MSO) attenuated lithi-um-pilocarpine-induced (Li-Pilo) seizures in young rats [1]. We hypothesized that the effect of MSO results from a) glutamine synthetase block-mediated inhibition of conversion of Glu/Gln precursors to neurotransmitter Glu, and/or from b) altered synaptic Glu release. Pilo was admin-istered 60 min prior to sacrifice, MSO at 75 mg/kg, i.p., 2.5 h earlier. [1,2-13C]acetate and [U-13C]glucose were i.p.-injected either together with Pilo (onset) or 15 min before sacrifice (final phase). Their conversion to Glu and Gln in hippocampus and entorhinal cortex was followed us-ing [13C] gas chromatography-mass spectrometry. Release of in vitro loaded [3H]D-Asp from ex vi-vo brain slices was measured in continuously collected superfusates. Protein and mRNA expres-sion were measured by Western Blot and real-time PCR techniques, respectively. At no time point nor brain region did MSO modify incorporation of [13C] to Glu or Gln in Pilo-treated rats. MSO pretreatment decreased by ~37% high potassium-induced [3H]D-Asp release and reduced by ~50% the synaptic vesicular Glu transporter VGLUT1 protein, but not mRNA content in the hippo-campus. The results indicate that MSO at non-convulsive dose mitigates the initial Pilo-induced seizures by interfering with synaptic Glu-release but not with neurotransmitter Glu recycling.

Ebola virus (EBOV) is a zoonotic pathogen causing severe hemorrhagic fevers in humans and non-human primates with high case fatality rates. In recent years, the number and extent of outbreaks has increased, highlighting the importance of better understanding the molecular aspects of EBOV infection and host cell interactions to control this virus more efficiently. Many viruses, including EBOV, have been shown to recruit host proteins for different viral processes. Based on a genome-wide siRNA screen, we recently identified the cellular host factor carbamoyl-phosphate synthetase 2, aspartate transcarbamylase, and dihydroorotase (CAD) to be involved in EBOV RNA synthesis. However, mechanistic details of how this host factor plays a role in the EBOV life cycle remain elusive. In this study, we analyzed the functional and molecular interactions between EBOV and CAD. To this end, we used siRNA knockdowns in combination with various reverse-genetics based lifecycle-modelling systems and additionally performed co-immunoprecipitation and co immunofluorescence assays to investigate the influence of CAD on individual aspects of the EBOV life cycle and to characterize the interactions of CAD with viral proteins. Following this approach, we could demonstrate that CAD directly interacts with the EBOV nucleoprotein NP, and that NP is sufficient to recruit CAD into inclusion bodies dependent on the GLN-domain of CAD. Further, siRNA knockdown experiments indicated that CAD is important for both viral genome replication and transcription, while substrate rescue experiments showed that the function of CAD in pyrimidine synthesis is indeed required for those processes. Together this suggests that NP recruits CAD into inclusion bodies via its GLN domain in order to provide pyrimidines for EBOV genome replication and transcription. These results define a novel mechanism by which EBOV hijacks host cell pathways in order to facilitate genome replication and transcription, and provide further basis for the development of host directed broad spectrum antivirals.

Alterations in the expression of glutamate/aspartate transporter (GLAST) have been associated with several neuropathological conditions including Alzheimer’s disease and epilepsy. However, the mechanisms by which GLAST expression is altered are poorly understood. Here we used a combination of pharmacological and genetic approaches coupled with quantitative PCR and Western blot to investigate the mechanism of the regulation of GLAST expression by a Ca2+/calmodulin-activated phosphatase calcineurin (CaN). We show that treatment of cultured hippocampal mouse and fetal human astrocytes with a CaN inhibitor FK506 resulted in a dynamic modulation of GLAST protein expression, being downregulated after 24-48 h, but upregulated after 7 days of continuous FK506 (200 nM) treatment. Protein synthesis, as assessed by puromycin incorporation in neo-synthesized polypeptides, was inhibited already after 1 h of FK506 treatment, while the use of a proteasome inhibitor MG132 (1 μM) shows that GLAST protein degradation was only suppressed after 7 days of FK506 treatment. In astrocytes with constitutive genetic ablation of CaN both protein synthesis and degradation were significantly inhibited. Taken together, our data suggest that, in cultured astrocytes, CaN controls GLAST expression at a posttranscriptional level through regulation of GLAST protein synthesis and degradation.

Since its inception, evolutionary theory has experienced a number of extensions. The most important of these took the forms of the Modern Evolutionary Synthesis (MES), embracing genetics and population biology in the early 20^th century, and the Extended Evolutionary Synthesis (EES) of the last thirty years, embracing, among other factors, non-genetic forms of inheritance. While we appreciate the motivation for this recent extension, we argue that it does not go far enough, since it restricts itself to widening explanations of adaptation by adding mechanisms of inheritance and variation. A more thoroughgoing extension is needed, one that widens the explanatory scope of evolutionary theory. In addition to adaptation and its various mechanisms, evolutionary theory must recognize as a distinct intellectual challenge the origin of what we call “historical kinds.” Under historical kinds we include any process that acquires a quasi-independent and traceable lineage-history in biological and cultural evolution. We develop the notion of a historical kind in a series of paradigmatic exemplars, from genes and homologues to rituals and music, and we propose a preliminary characterization.

Preventing muscle wasting in certain chronic diseases including cancer is an ongoing challenge. Studies have shown that polyphenols derived from fruits and vegetables show promise in reducing muscle loss in cellular and animal models of muscle wasting. We hypothesized that polyphenols derived from plum (Prunus domestica) could have anabolic and anti-catabolic benefits on skeletal muscle. The effects of a polyphenol-enriched plum extract (PE60) were evaluated in vitro on C2C12 and Colon-26 cancer cells. Treatment of myocytes with plum extract increased the cell size by ~3-fold (p<0.05) and stimulated myoblast differentiation by ~2-fold (p<0.05). Plum extract induced total protein synthesis by ~50% (p<0.05), reduced serum deprivation- induced total protein degradation by ~30% (P<0.05), and increased expression of IGF-1 by ~2-fold (p<0.05). Plum extract also reduced TNFα-induced NFkB activation by 80% (p<0.05) in A549/NFkB-luc cells. In addition, plum extract inhibited growth of Colon-26 cancer cells, and attenuated cytotoxicity in C2C12 myoblasts induced by soluble factors released from Colon-26 cells. In conclusion, our data suggest that plum extract may have pluripotent health benefits on muscle based on its demonstrated ability to promote myogenesis, stimulate muscle protein synthesis, and inhibit protein degradation. It also appears to protect muscle cell from tumor-induced cytotoxicity.

We have synthesized quinoxaline analogs (1-25), characterized by 1HNMR and HREI-MS and evaluated for thymidine phosphorylase inhibition. Among the series, nineteen analogs showed better inhibition when compared with the standard inhibitor 7-Deazaxanthine (IC50 = 38.68 ± 4.42 µM). The most potent analog among the series is analog 25 with IC50 value 3.20 ± 0.10 µM. Sixteen analogs 1, 2, 3, 4, 5, 6, 7, 12, 13, 14, 15, 16, 17, 18, 21and 24 showed outstanding inhibition which is many folds better than the standard 7-Deazaxanthine. Two analogs 8 and 9 showed moderate inhibition. A structure- activity relationship has been established mainly based upon the substitution pattern on the phenyl ring. The binding interactions of the active compounds were confirmed through molecular docking studies.

Microsporidia are fungi-like parasites that have the smallest known eukaryotic genome, and for that reason they are used as a model to study the phenomenon of genome decay in parasitic forms of life. Similar to other intracellular parasites that reproduce asexually in an environment with alleviated natural selection, Microsporidia experience continuous genome decay driven by Muller's ratchet - an evolutionary process of irreversible accumulation of deleterious mutations, which leads to gene loss and miniaturization of cellular components. Particularly, Microsporidia have remarkably small ribosomes in which the rRNA is reduced to the minimal enzymatic core. To better understand the impact of Muller's ratchet on RNA and protein molecules in parasitic organisms, particularly regarding their ribosome structure, we have explored an apparent effect of Muller's ratchet on microsporidian ribosomal proteins. Through mass spectrometry, analysis of microsporidian genome sequences and analysis of ribosome structure from non-parasitic eukaryotes, we found that massive rRNA reduction in microsporidian ribosomes appears to annihilate binding sites for ribosomal proteins eL8, eL27, and eS31, suggesting that these proteins are no longer bound to the ribosome in microsporidian species. We then provided an evidence that protein eS31 is retained in Microsporidia due to its non-ribosomal function in ubiquitin biogenesis. To sum up, our study illustrates that while Microsporidia carry the same set of ribosomal proteins as non-parasitic eukaryotes, some of ribosomal proteins are no longer participating in protein synthesis in Microsporidia and they are preserved from genome decay by having extra-ribosomal functions.

The development of a method to produce coumarins unsubstituted on the pyranic nucleus catalyzed from Wells–Dawson heteropolyacid (H₆P₂W₁₈O₆₂), phenol derivatives and ethyl 3,3-diethoxypropionate using Pechmann condensation under solvent-free conditions is described. This catalytic method was also applied successfully to synthesize various substituted coumarins, including the corresponding phenols and ethyl 3,3-diethoxypropionate. This work provides a novel, cheaper and safer way to syhthesize coumarins unsubstituted on the pyranic nucleus.

A good optical quality crystal of 2-aminopyridine (2AP) metal complex crystals was grown by slow evaporation technique at room temperature. The transparent and defect less bulk size of 2-aminopyridine potassium dihydrogen orthophosphate metal complex crystals have been grown by solution growth method. The molecular structure and morphology of grown crystals was drawn and planes are indexed using WINXMORPH software. A optical absorption spectrum, the UV cut-off wavelength, Band gap (Eg), Reflectance (R), Refractive Index (n), Extinction coefficient (K) and Electrical susceptibility (χc) are calculated for 2AP metal complex crystals.

The purpose of our work was the search for safe and effective biologically active substances of cardiotropic action among 1,3- thiazole derivatives. New derivatives of 1-[(2Z)-2-[R-imin]-4-methyl-3-R¹-2,3-dihydro-1,3-thiazole-5-yl]ethan-1-one and ethyl-(2Z)-2-[R-imin]-4-methyl-3-R¹-2,3-dihydro-1,3-thiazole-5-carboxylate were synthesized by the Hantzsch reaction. The structure of the compounds obtained was confirmed by ¹H NMR spectroscopy and by the elemental analysis. The pharmacological screening showed that the obtained substances possess cardiotropic activity. The cardiotropic properties of the new 1,3-thiazole derivatives were studied on the isolated rings of the thoracic aorta of laboratory rats. A prospective substance 1-[(2Z)-2-[(4-methoxyphenyl)imin]-4-methyl-3-(4-methylpiperazin-1-yl) -2,3-dihydro-1,3-thiazol-5-yl]ethan-1-one hydrochloride, which exhibits cardiotropic activity exceeding the activity of L-carnitine and meldonia has been revealed during pharmacological researches of the substances obtained.

Synthesis of new series of 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea derivatives and its in vitro antiproliferative activities against NCI-60 human cancer cell lines of nine different cancer types are described. Fourteen compounds 5a-n have been synthesized with three different hydrogen bondable moieties (4-hydroxylmethylpiperidinyl and trimethoxyphenyloxy and 4-hydroxyethylpiperazine) attached to the core structure 1-phenyl-3-(4-(pyridin-3-yl) phenyl) urea. Different substituents with different π and σ values were added on the terminal phenyl group. Compounds with 4-hydroxymethylpiperidine moiety showed higher mean percentage inhibition values over the 60-cell line panel at 10-µM concentration. They showed broad-spectrum antiproliferative activity over many cell lines of different cancer types. For instance, compound 5a elicited some lethal rather than inhibition effects on SK-MEL-5 melanoma cell line, 786-0, A498, RXF 393 renal cancer cell lines, and MDA-MB-468 breast cancer cell line by 146.1, 108.7, 136.2, 134.8, 116.6 % at 10 µM, respectively. Compounds 5a-e exhibited superior antiproliferative activity than Paclitaxel and Gefitinib against the most sensitive cell lines. Two compounds, 5a and 5d showed promising mean growth inhibitions and thus were further tested at five-dose testing mode to determine their IC₅₀ values. The data revealed that 5a and 5d urea compounds are the most active derivatives with significant efficacies and superior potencies than Paclitaxel in 21 different cancer cell lines, belonging particularly to renal cancer and melanoma cell lines. Moreover, 5a and 5d had superior potencies than Gefitinib in 38 and 34 cancer cell lines, respectively; belonging particularly to colon cancer, breast cancer and melanoma cell lines.

Silver nanoparticles (AgNPs) have been demonstrated to restrain bacterial growth while maintaining the minimal risk in development of bacterial resistance and human cell toxicity that conventional silver compounds exhibit. Several physical and chemical methods have been reported to synthesize AgNPs. However, these methods are expensive and involve heavy chemical reduction agents. An alternative approach to produce AgNPs in a cost-effective and environmentally friendly way employs a biological pathway using various plant extracts to reduce metal ions. The size control issue and the stability of nanoparticles remain some of the latest challenges in such methods. In this study, we used two different concentrations of fresh leaf extract of the plant Arbutus Unedo (LEA) as a reducing and stabilizing agent to produce two size variations of AgNPs. UV-Vis spectroscopy, Dynamic Light Scattering, Transmission Electron Microscopy and zeta potential were applied for the characterization of AgNPs. Both AgNP variations were evaluated for their antibacterial efficacy against the gram-negative species Escherichia coli and Pseudomonas aeruginosa, as well as the gram-positive species Bacillus subtilis and Staphylococcus epidermidis. Although significant differences have been achieved in the nanoparticles’ size by varying the plant extract concentration during synthesis, the antibacterial effect was almost similar.

A comprehensive kinetic model of the Fischer-Tropsch synthesis (FTS) is developed in a fixed bed reactor under operating conditions (temperature, 230–235°C, pressure, 20–25 bar, gas hourly space velocity, 4000–5000 cm³(STP)/h/g_catalyst ,H₂/CO feed molar ratio, 2.1) over a Co based catalyst. Reaction rate equations based on Eley-Rideal (ER) type model for initiation step and Langmuir-Hinshelwood-Hougen-Watson (LHHW) type model for propagation and termination steps of the FTS reactions have been considered and the readsorption of olefins were taken into account. The model that was reported in the literature was modified in order to explain many significant deviations from the ASF distribution. Optimum parameters have been obtained by Genetic Algorithms (GA). The calculated activation energies to produce n-paraffins and 1-olefins were in the range of 82.24 to 90.68 kJ/mol and 100.66 to 105.24 kJ/mol, respectively. The hydrocarbon distribution in FTS reactions was satisfactorily predicted particularly for paraffins.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

Nanoscience is a rapidly growing science stream that has been one of the cost-effective and energy-efficient approaches with wide applications. Water pollution is a major issue that is increasing continuously due to anthropogenic activities and several organic and inorganic contaminants. To overcome this issue, nanoparticles (NPs) have been successfully used to treat water. These NPs possess many beneficial applications in many fields like agriculture, cosmetics, photoconductors, environmental biotechnology, glass and alloy production, solar cells, nanomedicine and drug deliveries, biosensors, food industries, etc. The properties comprising high surface area, greater chemical reactivity, and mechanical properties play a vital role in imparting such beneficiary properties. As a result, there has been an increasing demand for the synthesis of NPs. However, excess usage of NPs further creates toxic by-products. Therefore, scientists and researchers are now focussing on the biogenic synthesis of NPs. The biological routes of NP synthesis have been crucial because they are eco-friendly and environmentally safe. This chapter highlights the usage of different approaches and biogenic sources for the production of NPs. It also discusses the recent advancement in the use of biogenic NPs with respect to applications for wastewater treatment.

The utilization of gold nanoparticles (AuNPs) has garnered significant attention in recent times, particularly in the field of biomedical research. The utilization of AuNPs in chemical synthesis procedures raises apprehensions regarding their potential toxicity in living organisms, which is inconsistent with their purported eco-friendly and cost-effective aspects. In this investigation, AuNPs were synthesized via the green synthesis approach utilizing Jeju Hallabong peel extract (HPE), a typical fruit variety indigenous to South Korea. The visible-range absorption spectrum of gold nanoparticles from green synthesis (HAuNPs) that are red wine in color occurs at a wavelength of λ = 517 nm. The morphology and particle size distribution were analysed using transmission electron microscopy (TEM) and ImageJ software. The TEM images reveal that the HAuNPs exhibit a high degree of dispersion and uniformity in their spherical shape, with an average size of approximately 7 nm. Moreover, elevating the initial pH level of the mixed solution has an impact on the decrease in particle dimensions, as evidenced by the blue shift observed in the UV-visible spectroscopy absorbance peak. Elevating the reaction temperature may accelerate the synthesis duration. However, it does not exert a substantial impact on the particle dimensions. The outcomes of an avidin-biocytin colorimetric assay provide preliminary analyses of possible sensor tunability using HAuNPs. The cytotoxicity of HAuNPs was evaluated through in vitro studies using the MTT assay on RAW 264.7 cell lines. The results indicated that the HAuNPs exhibited lower cytotoxicity compared to both chemically reduced gold nanoparticles (CAuNPs) and commercially available gold nanoparticles (SAAuNPs).

Building heterojunction is promising strategy for the achievement of highly efficient photocatalysis. In this study, a novel SnIn4S8@ZnO Z-scheme heterojunction with tight contact interface was successfully constructed through a facile two-step hydrothermal method. The phase composition, morphology, and photophysical properties of SnIn4S8@ZnO were studied through a series of characterization methods, respectively. Methylene blue (MB) was selected as the target pollutant for photocatalytic degradation and the degradation process was fitted with pseudo-first order kinetics. The as-prepared SnIn4S8@ZnO heterojunctions exhibited outstanding photocatalytic activities for the degradation of MB. The optimized sample (ZS800), in which the molar ratio of ZnO to SnIn4S8 was 800, displayed the highest photodegradation efficiency of MB (91%) within 20 min. Furthermore, the apparent rate constant of photodegradation for MB of ZS800 (0.121 min−1) was 2.2 times higher than that of pure ZnO (0.054 min−1). The improvement of photocatalytic activity could be attributed to the effective spatial separation of photogenerated charge carriers through a Z-scheme heterojunction with intimate contact interface. This work will provide a new insight into constructing excellent ZnO-based photocatalytic systems for wastewater purification.

Nanoparticles (NPs) have uniform chemical composition, size, and morphology. Microorganisms are of great interest in Nanoparticle synthesis. The green production of nanomaterials occurs either intracellularly or extracellularly. Gold and silver nanoparticles are mostly synthesised by the enzymatic degradation of metal ions. The produced NPs are characterized by different instruments such as ultraviolet visible, dynamic light scattering, x-ray diffraction, scanning electron microscope, transmission electron microscope, etc. Our review discusses the various biomedical applications of gold and silver nanoparticles synthesized by microbes via intracellular and extracellular mechanisms.

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

The frequency synthesizer is a critical component in Cs beam clock technology. In this paper, we present a demonstration of a direct microwave frequency-synthesis chain for a cesium-beam atomic clock, which utilizes frequency multiplication and a dual-phase-locked loop mode. A detailed analysis of the frequency-synthesis chain is conducted, and a mathematical model is established. The phase settling time and system stability are simulated, measured, and verified. The experimental results for the phase settling time align with the simulation outcomes. The phase settling time can be adjusted within the range of 644.5 µs to 1.5 ms, and the absolute phase noise values are -63.7 dBc/Hz, -75.7 dBc/Hz, -107.1 dBc/Hz, and -122.5 dBc/Hz at 1 Hz, 10 Hz, 1 kHz, and 10 kHz offset frequencies, respectively. Additionally, the Ramsey fringes are detected, and the Allan deviations of the 10 MHz output from the cesium-beam atomic clock are measured to be 2.99×10−12 at 1s and 8.02×10−14 at 10,000 s.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

Present study reports the green synthesis of pectin fabricated silver-based nanocomposite (Pectin-AgNPs) with Carpesiumnepalense leaves extract and evaluated their bactericidal kinetics, in-vivo hepatoprotective and cytotoxic potentials with their possible mechanisms. GC/MS and LC/MS analysis indicated the presence of different new phytochemicals constituents in the plant extract. The physicochemical characterization of Pectin-AgNPs by UV/Vis, SEM, DLS, FTIR and EDX techniques showed the spherical and uniform size range synthesis of nanocomposite i.e. 50-110 nm. The highly significant (P<0.005) antibacterial activity was found against all tested four bacterial strains with the ZIs of 24.8 to 27.2 mm. Significant damage in bacterial cell membrane was also observed in AFM study after treated with Pectin-AgNPs. At the doses of 0.05 mg/kg, nanocomposite showed highly significant (P<0.005)hepatoprotective activity in biochemical and histopathology analysis as compared to CCL4 administered control group. The ameliorative effects of Pectin-AgNPs were observed in PCR analysis on both GAPDH and PPARs genes expression and its potential to restore gene alterations caused by CCl4 intoxication.Pectin-AgNPs produced cytotoxic activity against HeLa cell lines at higher doses with the LC50 of 223.7 µg/mL. The current findings demonstrate positive attributes of pectin fabricated AgNPs as a promising antibacterial, hepatoprotective and cytotoxic agent.

The supramolecular based macrocyclic amphiphiles have attracted great attention in the field of drug delivery due to their unique self-assembling nature. Therefore, these macrocycles are used as nanocarriers for the delivery of poor water soluble drugs, and also for those which have lower permeability, and cannot cross the barrier to reach the desired site. Herein, we design and synthesized a new supramolecular amphiphilic macrocycle to overcome these problems. The macrocycle was synthesized in two steps. In first step 4-hydroxybenzaldehyde was treated with 1-bromotetradecane to obtain a derivatized product which was then treated with resorcinol to cyclize and get calix(4)resorcinarene based supramolecular amphiphilic macrocycle. The synthesized macrocycle and intermediate products were characterized by Mass spectrometry, IR and 1H-NMR spectroscopic techniques. The amphiphile was screened for biocompatibility studies, vesicles formation, and then Amphotericin-B was loaded in the supramolecular amphiphile based vesicles and was characterized for shape, size, homogeneity, surface charge, drug entrapment, in-vitro release profile and stability through atomic force microscopy (AFM), Zetasizer, HPLC and FT-IR. Amp-B loaded macrocycle based vesicles were investigated for in-vivo bioavailability in rabbits. The synthesized macrocycle was nontoxic in cancer cells, hemo-compatible and safe in mice. The drug-loaded macrocycle based vesicles appeared spherical, nano-ranged, and homogeneous in size with negative surface charge and were able to load an increased amount of drug. The vesicles are stable upon storage and when incubated with gastric simulated fluid. Amp-B increased oral bioavailability was achieved when delivered in synthesized macrocycle based vesicles. These results point out that the synthesized supramolecular amphiphile is an efficient nanocarrier to enhance the oral bioavailability of lipophilic drugs

We present a crack-free optically active SiO2 glass-composite material containing YAG:Ce synthesized by a modified sol-gel technique. A glass-composite material consisting of yttrium aluminum garnet doped with Ce3+ (YAG:Ce) entrapped into a SiO2 xerogel. This composite material has been prepared by sol–gel technique with modified gelation and drying process to obtain crack-free optically active SiO2 glass. The concentration of the YAG:Ce was from 0.5 to 2.0 wt%. All synthesized samples were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM) techniques. The luminescence properties of the obtained materials were studied.

Data scarcity is a significant challenge in the field of Machine Learning (ML), as data collection can be expensive, time-consuming, and difficult, particularly in developing countries. This challenge is exaggerated on the need to use dataset for livestock disease predictions for early intervention and surveillance. To address this challenge, this paper presents a data synthesis method that has been used to accurately generate new data samples from few real-world data. With much data available to train the ML models, overfitting is eliminated. We present the use of Generative Adversarial Networks mainly the Conditional Tabular Generative Adversarial Network to synthesize categorical data for training machine learning models for prediction of the Pestes des Petits Ruminants (PPR) disease. The results showed that training score became 0.89 and the cross-validation score was 0.87 after synthesized data was used with Random Forest algorithm. The resulting dataset can be used to support the prediction and surveillance of the Pestes des Petits Ruminants (PPR) disease. The proposed method can also be applied to any domain with categorical data, and has the potential to improve the performance of machine learning models with increased data availability.

The article proposes to use a radio holography for the detection and identification of unmanned aerial vehicles (UAVs).

A series of novel indole Schiff base derivatives (2a–2t) containing a 1,3,4-thiadiazole scaffold modified with a thioether group were synthesized, and their structures were confirmed using FT-IR, ¹H NMR, ¹³C NMR, andHR-MS. In addition, the antifungal activity of synthesized indole derivatives was investigated against Fusarium graminearum (F. graminearum), Fusarium oxysporum (F. oxysporum), Fusarium moniliforme (F. moniliforme), Curvularia lunata (C. lunata), and Phytophthora parasitica var. nicotiana (P. p. var. nicotianae) using the mycelium growth rate method. Among the synthesized indole derivatives, compound 2j showed the highest inhibition rates of 100%, 95.7%, 89%, and 76.5% at a concentration of 500 μg/mL against F. graminearum, F. oxysporum, F. moniliforme, and P. p. var. nicotianae, respectively. Similarly, compounds 2j and 2q exhibited higher inhibition rates of 81.9% and 83.7% at a concentration of 500 μg/mL against C. lunata. In addition, compound 2j has been recognized as a potential compound for further investigation in the field of fungicides.

Adventurous play, defined as exciting, thrilling play where children are able to take age-appropriate risks has been associated with a wide range of positive outcomes. Despite this, it remains unclear what factors might aid or hinder schools in offering adventurous play opportu-nities. The purpose of this systematic review is to synthesise findings from qualitative studies on the perceived barriers and facilitators of adventurous play in schools. A total of nine studies were included in the final synthesis. The review used two synthesis strategies: a meta-aggregative syn-thesis and narrative synthesis. Findings were similar across the two syntheses, highlighting that key barriers and facilitators were: adults’ perceptions of children; adults’ attitudes and beliefs about adventurous play and concerns pertaining to health; and, safety and concerns about legis-lation. Based on the findings of the review, recommendations for policy and practice as provided to support adventurous play in schools.

Background:Boom in nanotechnology in current era has sketched unforeseen transformations in number of fields, such as medicine, health care, food, space, agriculture, etc. The synthesis of nanoparticles with different chemical compositions, sizes, shapes and controlled disparities is an important area of research in this field. Over the last decade, the biosynthesis of metal nanoparticles has received considerable attention due to their unusual and fascinating properties, with various applications, over their bulk counterparts.Hypothesis: The nanoparticle can have huge application in the field of food, pharmaceutical, and cosmetic industries and thus become a major area of research. Green synthesis of zinc oxide nanoparticles (ZnO NPs) using plant extracts offers an eco-friendly and promising substitute to the conventional methods of chemical synthesis. Conclusion: In the arena of nanoparticle phytosynthesis, novel materials have been produced that are eco-friendly, cost-effective and stable. In the current situation, nanotechnology inspires progress in all spheres of life, and therefore the phytosynthetic path of nanoparticle synthesis has emerged as a safe and best alternative to conventional methods. This review summarizes the recent work in the field of zinc nanoparticle phytosynthesis and critically discusses the mechanism proposed behind it.

CoCr2O4 and doped lithium Co1-xLixCr2O4 chromate powder and nanoparticles were prepared by modified by sol-gel method. The morphological and structural properties of nano chromates were investigated by x-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and Photoluminescence (PL). Nanoparticles of doped lithium were synthesized by adding appropriate amount of cobalt nitrate, chromium nitrate, lithium nitrate and 1,2 Ethanediol as a complexing agent. The sample were heated at 105 ˚C for ten hours in oven to obtain dry gel. Calcination temperature for these samples was 700˚C for 3 hours in a furnace. The particle size of parent compound ranges from 4.4 nm to 11 nm, determined by SEM. The tendency of particles to form the aggregates with the increased annealing temperature was observed. The SEM and optical characterization of this compound has shown the sol gel derived material may be successfully used as an effective doped lithium cobalt ceramic pigment with controlled variation in structural and optical properties. SEM images showed that spherical like doped particle have diameter 33nm. From PL spectra Nano structure shows band gap 2.5ev and when we doped Lithium in it band gap decreases and become 1.19ev, which is associated to band gap transition.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

In this paper, an electromechanical mass lifter system is designed, analyzed and compare using optimal and robust control theories. LQR and μ -synthesis controllers are used to improve the lift displacement by comparison method for tracking the desired step and sinusoidal wave signals input. Finally, the comparison simulation result prove the effectiveness of the electromechanical mass lifter system with μ -synthesis controller for improving the rise time, percentage overshoot, settling time and peak value of tracking the desired step displacement signal and improving the peak value for tracking the desired sinusoidal displacement signal with a good performance.

This paper studies the use of zinc oxide nanoparticles (ZnO-NPs) synthesized using an extract of convolvulus leaves and expired ZnCl₂, as an efficient inhibitor for carbon steel corrosion in 1M HCl solution. ZnO-NPs are characterized by Fourier-transform infrared spectrophotometer (FTIR) and UV–Vis analysis. The technique of weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) has also been used to investigate the prevention of carbon steel corrosion in 1M HCl. The results showed that the efficiency of restraint increased when the concentration of ZnO-NPs was raised to 91% and that the inhibition efficiency is still high despite its decrease at high temperature, and it acts as a mixed-type inhibitor A sample of carbon steel with the protective inhibitor layer on top was immersed for 20 hours and observed; an increase in the charge transfer resistance (Rct) and stability of the inhibitor was noticed after 6 hours. Adsorption isotherm models demonstrated that the inhibitor adsorption mechanism on the carbon steel surface followed Langmuir, more than Freundlich and Temkin, behavior. The thermodynamic parameters showed that the adsorption process is a mixed adsorption, spontaneous, and exothermic. The results illustrated that the acid medium was a strong inhibitor of carbon steel corrosion. Scanning electron microscope (SEM) showed that the ZnO-NPs formed a good protective film on the carbon steel surface.

To date electric pianos and samplers tend to concentrate on authenticity in terms of temporal and spectral aspects of sound. They barely recreate the original sound radiation characteristics, contribute to the perception of width and depth, vividness and voice separation, especially for instrumentalists, who are located in the near field. This paper describes an operational procedure to measure, store, and synthesize the complete sound of a harpsichord, including its spatial sound radiation characteristics. First, actuators excite the instrument at the intersection point of each string with the bridge with an exponential sine-sweep. Then, the radiated sound field is recorded in the near and the far field with microphone arrays. The pressure distribution in the near field is propagated back to the soundboard of the instrument, using Minimum Energy Method. The vibration of each single string is captured with lightweight contact microphones. The soundboard is then replaced by an array of 128 loudspeakers. The loudspeaker signal is a convolution of the back-propagated sweep recording with the string recording to perform a wave field synthesis. Above the spatial Nyquist frequency, the Radiation Method is applied to perform a sound field synthesis which is valid for the listening region of the instrumentalist. The result is an electric harpsichord, that approximates the sound of a real harpsichord precisely in time, frequency, and space domain. Applications for such a radiation keyboard are music performance, instrument and synthesizer building and interactive psychoacoustic research.

New class of triazinoindole bearing thiosemicarbazide (1-25) was synthesized and evaluated for α-glucosidase inhibitory potential. All synthesized analogues exhibited excellent inhibitory potential having IC50 values ranging from 1.30 ± 0.01 to 35.80 ± 0.80 µM when compared with the standard acarbose having IC50 value 38.60 ± 0.20 µM. Among series the analogues 1 and 23 was found the most potent having IC50 values 1.30 ± 0.05 and 1.30 ± 0.01 µM respectively. Structure activity relationship (SAR) was mainly based upon by bring about difference of substituents on phenyl rings. To confirm the binding interactions, molecular docking study was performed. Synthesized analogues were characterized through HREI-MS, 1H and 13C-NMR analysis.

In this paper we present an efficient technique for the synthesis of very large sparse arrays, with arbitrary circularly symmetrical upper bounds for the pattern specifications. The algorithm, that is based on iterative smooth re-weighted L1 minimizations is very flexible, and is capable of achieving very good performances with respect to competitive algorithms. Furthermore, thanks to its efficiency, planar arrays of hundreds of wavelengths can be synthesized with limited computational effort.

We present an idea how to use long-wavelength multi-wavelength radio continuum observations of spiral galaxies to isolate magnetic structures which were previously accessible from short-wavelength observations only. The approach is based on the RM-synthesis and 2D continuous wavelet transform. Wavelet analysis helps to recognize a configuration of small-scale structures which are produced by Faraday dispersion. We find that these structures can trace galactic magnetic arms for the case of the galaxy NGC 6946 observed at $\lambda = 17 \div 22$~cm. We support this interpretation by an analysis of a synthetic observation obtained using a realistic model of a galactic magnetic field.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Carbon nanotubes are hybridized with metal crystals to impart multifunctionality into the nanohybrids (NHs). Simple but effective synthesis techniques are desired to form both zero-valent and oxides of different metal species on carbon nanotube surfaces. Sol-gel technique brings in significant advantages and is a viable technique for such synthesis. This study probes the efficacy of sol-gel process and aims to identify underlying mechanisms of crystal formation. Standard electron potential (SEP) is used as a guiding parameter to choose the metal species; i.e., highly negative SEP (e.g., Zn) with oxide crystal tendency, highly positive SEP (e.g., Ag) with zero-valent crystal-tendency, and intermediate range SEP (e.g., Cu) to probe the oxidation tendency in crystal formation are chosen. Transmission electron microscopy and X-ray diffraction are used to evaluate the synthesized NHs. Results indicate that SEP can be a reliable guide for the resulting crystalline phase of a certain metal species, particularly when the magnitude of this parameter is relatively high. However, for intermediate range SEP-metals, mix phase crystals can be expected. For example, Cu will form Cu₂O and zero-valent Cu crystals, unless the synthesis is performed in a reducing environment.

Ferroelectric materials are crucial for today’s technological society, and nanostructured ferroelectric materials are important for downscaling of devices. Controlled and reproducible synthesis of these materials are therefore of immense importance. Hydrothermal synthesis is a well-established synthesis route, with a large parameter space for optimization, but a better understanding of nucleation and growth mechanisms is needed for full utilization and control. Here we use in situ X-ray diffraction to follow the nucleation and growth of BaTiO₃ formed by hydrothermal synthesis using two different titanium precursors, an amorphous titania precipitate slurry and a Ti-citric acid complex solution. Sequential Rietveld refinement was used to extract the time dependency of lattice parameters, crystallite size, strain and atomic displacement parameters. Phase pure BaTiO₃ nanoparticles 10 - 15 nm in size were successfully synthesized at different temperatures (100, 125, and 150 °C) from both precursors after reaction times ranging from a few seconds, to several hours. The two precursors resulted in phase pure BaTiO₃ with similar final crystallite size. Finally, two different growth mechanisms were revealed, where the effect of surfactants present during hydrothermal synthesis is discussed as one of the key parameters.

2017 was an excellent year in terms of new drugs (chemical entities and biologics) approved by the FDA, with a total of forty-six. In turn, one of the highlights was the number of peptides (six) included in this list. Here, the six peptides are analysed in terms of chemical structure, synthetic strategy used for their production, source, biological target, and mode of action.

Using the techniques of computer-aided drug design, the docking of Survivin and known active small molecules was simulated and then the key amino acid residue fragment of the target protein was analyzed. It led to the discovery of active groups capable of binding to the critical sites. Through the use of the natural product, Oleanolic Acid, as a lead compound, the introduction of the active groups onto the A-ring, and the modification of the carboxyl group at the C-28 position using esterification or amidation, twenty new Oleanolic acid derivatives had been designed and synthesized.A549 and SGC-7901 cells were used to screen the antitumor activity in vitro through the standard MTT method. The compounds, II₃, III₅ and Ⅳ_4, exhibited more potent cytotoxicity than positive drugs.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.