Considering rotation-induced centrifugal stiffening, spin softening, and Coriolis effects, the three-dimensional finite element model of a rotating blade with a dovetail structure is built through the contact dynamics theory. The fixed-interface component mode synthesis method is then adopted to reduce the model for high computational efficiency and adequate model accuracy. The effects of the number of normal modes on the first-six-order modal characteristics of the model varying with the rotating speed are studied between the reduced and full models. Next, the influence of rotating speed and friction factor on the nonlinear dynamic characteristics of the model under the action of aerodynamic force are elaborately discussed. The results show that: (1) tenon-mortise joint contact-induced nonlinearity under low rotating speeds results in the intermittent interference of contact surfaces and frequency multiplications of aerodynamic excitation frequency in the spectrum cascades, while that under high rotating speeds causes the continuous interface contact and asynchronous excitation at the tenon-mortise joint; (2) the increase of friction factor results in a lower contact pressure distribution and the right shift of the resonance peak (i.e., hard nonlinearity).

In this study we present gas-phase fluorination as a method to create a thin LiF layer on Li6.5La3Zr1.5Ta0.5O12 (LLZTO). We compare these fluorinated films with LiF films produced by RF-magnetron sputtering, where we investigated the interface between the LLZTO and the deposited LiF showing no formation of a reaction layer. Furthermore, we investigate the ability of this LiF layer as a protection layer against Li2CO3 formation in ambient air. By this we show that Li2CO3 formation is absent at the LLZTO surface after 24 h in ambient air supporting the protective character of the formed LiF films and hence could enhance the handling of LLZTO in air for battery production. With respect to the use within hybrid electrolytes consisting of LLZTO and a mixture of polyethylene oxide (PEO) and Lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) we also investigated the interface between the formed LiF films and a mixture of PEO LiTFSI by X-ray photoelectron spectroscopy (XPS) showing decomposition of the LiTFSI at the interface.

The work contains a detailed analysis of the electromagnetic field originating from a point source placed above the layered structure.The surface impedance of the multilayer dielectric structure was determined. Based on the boundary conditions, a method for determining the surface impedance of a layered structure with a perfectly conductive screen and or a magnetic screen is presented. The resonance conditions and the conditions for the excitation of surface waves are derived. The integral expression defining the generalized impedance was analyzed with a view to adapting it to numerical implementation. This allowed the development of a computer program based on which calculations were made of the effect of excitation of waves on multilayer dielectric substrates.

This study aims to develop an in-situ field repair approach, special for aircraft composite structures, to enhance the interlaminar toughness of plain woven composites (PWCs) by adding multi-walled carbon nanotubes (MWCNTs). MWCNTs are dispersed at each interface between prepreg layers by means of solvent spraying with the density is 1.58 g/m2. And then, the layers are stacked with the predefined sequence and cured at 120℃ and 1 bar pressure using the heat repairing instrument. Moreover, double cantilever beam (DCB) standard test is used to investigate the interlaminar toughening effect due to the MWCNTs. For comparison, original samples are also prepared, the results indicate that the introduction of MWCNTs can favorably enhance the interlaminar toughness of PWCs at field repair approach and the Mode I fracture energy release rate GIC increases by 102.92%. Based on finite element method (FEM) of continuum damage mechanics, the original and MWCNTs toughening specimen under DCB Mode I fracture are modeled and analyzed. The simulation and experiment are in good agreement. Finally, the toughening mechanism of MWCNTs is explored by scanning electron microscope (SEM), it is founded that a large amount of Fiber-matrix (F-M) interface debonding and matrix cracking of mountain shape are the major modes of fracture accompanied with few fiber breakage and matrix peeling off for the MWCNTs toughening specimens.

Thin films of BiFeO3 (BFO), VO2 and BFO/VO2 were grown on SrTiO3(100) and Al2O3(0001) monocrystalline substrates using the RF and DC sputtering techniques. The surface of the films was characterized by profilometry, AFM, and XPS. The heterostructures have roughnesses between 0.2 and 16 nm and a grain size between 20 nm and 67 nm. XPS measurements show a higher proportion of the V4+ and Bi3+ oxides. In the Fe region, a higher proportion of Fe3+ is shown in the films. The homogeneous ordering, low roughnesses, and the oxidation states on the obtained surface show a good coupling in these films. The I-V curves show ohmic behavior at room temperature and change with increasing temperature. The effect of coupling these materials in a thin film shows the appearance of hysteresis cycles I-V and R-T, typical of materials with high potential in applications such as resistive memories and solar cells.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

A new strategy to nanoengineer gold/fluorocarbon multilayer (ML) nanostructures is reported. We have investigated the morphological changes occuring at the metal-polymer interface in multilayer structures with varying volume fraction of gold (Au) and the kinetic growth aspect of the microscale properties of nano-sized Au in plasma polymer fluorocarbon (PPFC). Investigations were carried out at various temperatures and annealing time by means of grazing incidence small-angle and wide-angle X-ray scattering (GISAXS and GIWAXS). We have fabricated a series of multilayers with variying volume fraction (0.12, 0.27, 0.38) of Au and bilayer periodicity in ML structure. They show an interesting granular structure consisting of nearly spherical shaped nanoparticles within the polymer layer. The nanoparticle (NP) morphology changes due to the collective effects of NPs diffusion within ensembles in the in-plane vicinity and inter-layer with increasing temperature. The in-plane NPs size distinctly increases (from 1.9 to 4 nm) with increasing temperature. The NPs become more spherical thus reducing the surface energy. Linear growth of NPs with temperature and time shows diffusion-controled growth of NPs in the ML structure. The structural stability of the multilayer is controlled by the volume ratio of the metal in polymer. At room temperature UV-Vis shows a blueshift of the plasmon peak from 560 nm in ML Au/PTFE_1 to 437 nm in Au/PTFE_3. We have identified the fabrication and post-deposition annealing conditions to limit the Local Surface Plasmon resonance (LSPR) shift (from 〖∆λ〗_LSPR=180 nm (Au/PTFE_1) to 〖∆λ〗_LSPR=67 nm (Au/PTFE_3 ML)) and their optical response over a wide visible wavelength range. A variation in the dielectric constant of the polymer in precence of varying Au inclusion is found to be the main factor affecting the LSPR frequency. Our finding may provide insights in Nano engineering ML structure can be useful to systematically control the growth of NPs in polymer matrix.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is > 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R > 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

Nowadays, the study of preparing silica/rubber composites, which can be used in “green tire”, in energy saving method is fast-growing. In our work, silica modified by using alcohol polyoxyethylene ether (AEO) and 3-Mercaptopropyltriethoxysilane (K-MEPTS) together were investigated. Thermal gravimetric analyzer (TGA) result indicated that both AEO and K-MEPTS could be grafted on the silica surface. Raman spectroscopy confirmed that the AEO could generate a certain steric hindrance for the mercaptopropyl group on K-MEPTS. Silica modified by using AEO and K-MEPTS together can be completely co-coagulated with the rubber in preparing silica/natural rubber (NR) composites by latex compounding method. AEO can form a physical interface between silica and rubber; meanwhile, K-MEPTS can form a chemical interface between silica and rubber. The effects of chemical and physical interface between silica and rubber on dynamic and mechanical performances of silica/NR composites were also given in this research. A proper combination of physical and chemical interface between silica and NR can improve performances of silica/NR composites.

As an essential synthetic material used in continuous casting of steels, mold fluxes improve the surface quality of steel slabs. In this study, a CaO-SiO₂-Na₂O based low-fluorine mold flux was solidified by an improved water-cooled copper probe with different temperatures of molten flux and different probe immersion times. The heat flux through solid films and the film structures were calculated and inspected, respectively. The results indicate: large internal cracks (formed in the glassy layer of films during solidification) were observed, the formation and evolution of those cracks contributed to the the unstable heat flux density. The roughness of the surface in contacted with the water-cooled copper probe formed as films were still glassy and the roughness have no causal relationship with crystallization or devitrification. Combeite with columnar and faceted dendritic shapes is the main crystal in the film.

In view of the complexity of the pile foundation underpinning structure system and the stringent requirements of the construction process, this paper briefly describes the necessity of introducing epoxy resin reinforcing adhesive of planting rebar in the design of pile foundation underpinning beam structure to im-prove the mechanical properties of the underpinning beam new and old concrete joint surfaces and proposes a new type of pile foundation underpinning beam system construction method by “chiseling + prestressed reinforcement + epoxy resin reinforcing adhesive”. This paper uses an actual pile foundation underpinning project of an urban overpass as a prototype, designs and creates a model structure with a similarity ratio of 1/6, and performs repeated pro-gressive static loading tests to study the load carrying capacity, displacement change, and other properties of the underpinning structure, as well as analyses and distorts the overall working performance and failure mode of them. On this basis, the prototype structure's finite element analysis model was built, and the finite element analysis results were compared with the test results to get the mechanical properties and deformation characters of the actual pile foundation under-pinning structure system corresponding to the actual underpinning beam load. This paper's study can lay the theoretical and experimental foundation for the smooth development of similar projects.

In this study, we design a new refractive index sensor based on a metal–insulator–metal waveguide coupled with a notched ring and vertical rectangular resonators. We use the finite element method to study the propagation characteristics of the sensor. According to the calculation results, the transmission spectrum exhibits a typical Fano resonance shape. The phenomenon of Fano resonance is caused by the coupling between the wide spectrum and narrow spectrum. In the design, the wide spectrum signal is generated by the vertical rectangular resonator, while the narrow spectrum signal is generated by the notched ring resonator. In addition, we varied the structural parameters of the resonators and filled the structure with media of different refractive indices to study the sensing properties. The maximum achieved sensitivity of the sensor reached 1071.4 nm/RIU. The results reveal potential applications of the coupled system in the field of sensors.

The objective of this study is to evaluate the effects of the 3D point cloud density derived from unmanned aerial vehicle (UAV) photogrammetry and structure from motion (SfM) and multi-view stereopsis (MVS) techniques, the interpolation method for generating a digital terrain model (DTM), and the resolution (grid size) of the derived DTM on the accuracy of estimated heights in small areas, where a very accurate high spatial resolution is required. A UAV-photogrammetry project was carried out on a bare soil of 13 × 13 m with a rotatory wing UAV at 10 m flight altitude (equivalent ground sample distance = 0.4 cm). The 3D point cloud was derived, and five sample replications representing 1, 2, 3, 4, 5, 10, 15, 20, 30, 40, 50, 60, 70, 80 and 90% of the original cloud were extracted to analyze the effect of cloud density on DTM accuracy. For each of these samples, DTMs were derived using four different interpolation methods (Inverse Distance Weighted (IDW), Multiquadric Radial Basis Function (MRBF), Kriging (KR), and Triangulation with Linear Interpolation (TLI)) and 15 DTM grid size (GS) values (20, 15, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0.67, 0.5, and 0.4 cm). Then, 675 DTMs were analyzed. The results showed, for each interpolation method and each density, an optimal GS value (most of the cases equal to 1 cm) for which the Root Mean Square Error (RMSE) is minimum. IDW was the interpolator which yielded best accuracies for all combination of densities and GS. Its RMSE, considering the raw cloud, was 1.054 cm. The RMSE increased 3% when a point cloud with 80% extracted from the raw cloud was used to generate the DTM. When the point cloud included the 40% of the raw cloud, RMSE increased 5%. For densities lower than 15%, RMSE increased exponentially (45% for 1% of raw cloud). The grid size minimizing RMSE for densities of 20% or higher was 1 cm, which represents 2.5 times the ground sample distance of the pictures used for developing the photogrammetry project.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

Forests are critical in regulating the world’s climate and they maintain overall Earth’s energy balance. The variability in forest canopy structure, topography and underneath vegetation background condition creates uncertainty in the estimation and modelling of Earth’s surface radiation particularly for boreal regions in high latitude. We studied seasonal variation in surface reflectance with respect to land cover classes, canopy structures, and topography in a boreal region of Alaska by fusing together Landsat 8 surface reflectance and LiDAR-derived canopy matrices. Our study shows that canopy structure and topography interplay and influence surface reflectance in a complex way particularly during the snow season. Topographic aspect and elevation control vegetation growth, type and structure. The southern slope is featured with more deciduous and taller trees having greater rugosity than the northern slope. Higher elevation is associated with taller trees for both vegetation types, particularly in the southern slope. In general, surface reflectance shows similar relationships with canopy cover, height and rugosity, mainly due to close relationships between these parameters. Surface reflectance decreases with canopy cover, tree height, and rugosity especially for evergreen forest. Deciduous forest shows larger variability of surface reflectance, particularly in March, mainly due to the mixing effect of snow and vegetation. The relationship between vegetation structure and surface reflectance is greatly impacted by topography. The negative relationship between elevation and surface reflectance may be due to taller and denser vegetation distribution in higher elevation. Surface reflectance in the southern slope is slightly larger than the northern slope for both deciduous and evergreen forest. The shadow effect from topography and tree crowns on surface reflectance play a different role for deciduous and evergreen forests. For deciduous forest, topographic shadow effect on surface reflectance is stronger than from tree shadowing in all seasons. For evergreen forest, shadow effects from topography and tree crowns on surface reflectance are both equally dominant, however tree shadow effect is more significant in March than in May and August. The generalized additive models (GAM) based on non-linear relationships between response (surface reflectance) and predictor (canopy structures and topography) variables confirms such observations. Our study not only provides accurate quantification of surface radiation budget but also helps in parametrization of climate change models.

The transferability of structure-property relationships for laser-pretreated metal adhesive joints to laser-pretreated metal – carbon fiber reinforced plastic (CFRP) bonds is investigated. Single-lap shear tests were performed on hybrid AW 6082-T6 – CFRP specimens pretreated with the same pulsed laser surface parameter sets on the metal surface as previously tested AW 6082-T6 – E320 metal adhesive joints. The fracture surfaces were characterized to determine the type of failure and elucidate differences and commonalities in the link between surface structures and single-lap shear strengths. Digital image analyses of the hybrid specimens fractured surfaces were used to quantify remaining CFRP fragments on the metallic joint side. The results indicate that high surface enlargements and the presence of undercut structures leads to single-lap shear strengths exceeding 40 MPa and 35 MPa for unaged and aged hybrid specimens respectively. While for the metal-polymer joints the trend from high strength to weakly bonded specimens was largely continuous with the degree of surface structuring, hybrid metal – CFRP joints exhibit a drastic drop in joint performance after aging if the laser-generated surface structures are less pronounced with low surface enlargements and crater depths. Surface features and hydrothermal aging determine whether the specimens fail cohesively or adhesively.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

We compare photoaligning properties of polymer layers fabricated from the same constituents: polymethyl-methacrylate (PMMA) and azo-dye Disperse Red 1 (DR1), either chemically attached to the PMMA main-chain, or physically mixed with it. Photoaligning properties depend on the preparation method drastically. This finding is supported by atomic force microscope (AFM) scans monitoring the light-induced changes at the polymer−air interface, and revealing a photoinduced mass transfer.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

As in many parts of the world, rural-urban, forest-urban interface areas surrounding urban regions expose the natural areas they interact with to a threat of fire risk that can reach various sizes. This risk has been assessed for various regions of the world using many different methods and numerical models so far. Among these, it is seen that machine learning models have successful applications in risk assessment and risk prediction studies. For the fire risk prediction of Istanbul's yet unurbanized regions, but where the city is anticipated to potentially shift, data was collected using the opportunities provided by Geographic Information Systems and Remote Sensing technologies based on fires that occurred between 2000-2021, and the region was examined. Machine learning methods' Random Forest (RF), Extreme Gradient Boosting (XGB), and Light Gradient Boosting (LGB) models were applied for the classification of factors effective in fire. The best result was given by the RF model with 0.93 accuracy, 0.062 F1 score, and 0.753 Area Under Curve (AUC) value. In the classification of factors in the RF model, the grouping between fire-initiating factors and factors effective in spreading is evident, while this distinction is partially noticeable in the other two models.

Full waveform (FW) LiDAR holds great potential for retrieving vegetation structure parameters at a high level of detail, but this prospect is constrained by practical factors such as lack of available handy processing tools and technical intricacy of waveform processing. This study introduces a new product, named the Hyper Point Cloud (HPC) derived from FW LiDAR data, and explore its potential applications such as tree crown delineation using the HPC-based intensity and percentile height (PH) surfaces, which show a promising solution to the constraints of using FW LiDAR data. Results of the HPC present a new direction to handle FW LiDAR data and offer prospects for studying the mid-story and understory of vegetation with high point density (~ 182 points/m2). The intensity-derived digital surface model (DSM) generated from the HPC shows that the ground region has larger maximum intensity (MAXI) and mean intensity (MI) than the vegetation region while having smaller total intensity (TI) and number of intensities (NI) at the given grid cell. Our analysis of intensity distribution contours at individual tree level exhibit similar patterns, indicating that the MAXI and MI are decreasing from the tree crown center to tree boundary while a rising trend is observed for TI and NI. These intensity variable contours provide a theoretical justification for using HPC-based intensity surfaces to segment tree crowns and exploit their potential for extracting tree attributes. The HPC-based intensity surfaces and the HPC-based PH Canopy Height Models (CHM) demonstrate promising tree segmentation results comparable to the LiDAR derived CHM for estimating tree attributes such as tree locations, crown widths and tree heights. We envision that products such as the HPC and the HPC-based intensity and height surfaces introduced in this study can open new perspectives to use FW LiDAR data and alleviate the technical barrier of exploring FW LiDAR data for detailed vegetation structure characterization.

Abstract: Interface risks are inherent in every construction project from start to finish. Identifying and managing these risks effectively in every project phase is crucial for actualising project objectives. This paper shows a comprehensive framework showing several relationships between project stakeholders and how the interface risks between them that influence project execution are identified and managed for the overall construction project success. Firstly, literature review on interfaces and interface risks were car-ried out and how organisations managed interface risks were discussed and secondly, the collection of quantitative data was conducted by means of structured online questionnaires. The sample consisted of 205 construction project professionals who were selected randomly. This group included individuals with various roles in the construction industry, The data was analysed using descriptive statistical methods, including factor analysis, reliability assessment, and calculations of frequencies and percentages. Finally, the results showed all the factors, work culture and organisational approaches that influence interface risk management and ways to identify and manage interface risks effectively.

The modulation instability of surface capillary-gravity water waves is analysed in a shear flow model with a tangential discontinuity of velocity. It is assumed that air blows along the surface of the water with a uniform profile in the vertical direction. Such a model, despite its simplicity, plays an important role in hydrodynamics as the reference model for investigating basic physical phenomena of wave-current interactions and acquiring insights into a series of complex phenomena. In certain cases where the wavelength of interfacial perturbations is much bigger than the width of the shear fow profile, the model with the tangential discontinuity in the velocity is adequate for describing physical phenomena at least within limited spatial and temporal frameworks. A detailed analysis of the air-flow conditions under which modulation instability sets in is presented. It is also shown that the interfacial waves are subject to dissipative or radiative instability when negativeenergy waves appear at the interface.

Photophysical properties of a series of bis(arylydene)cycloalkanone dyes with various donor substituentns are studied by quantum chemistry. Their capacity for luminescence and nonradiative relaxation through trans-cis isomerization is related to their structure, in particular, to the donor capacity of the substituents and the degree of conjugation due to the central cycloalkanone moiety. It is shown that cyclohexanone central moiety introduces distortions and disrupts the conjugation, thus leading to a nonmonotonic change in their properties. The increasing donor capacity of the substituents causes increase in the HOMO energy (raise of the oxidation potential) and decrease in the HOMO-LUMO gap, which results in the red shift of the absorption spectra. The ability of the excited dye to relax through fluorescence or through trans-cis isomerization is governed by the height of the barrier between the Franck–Condon and S1-S0 conical intersection regions on the potential energy surface of the lowest π-π* excited state. This barrier also correlates with the donor capacity of the substituents and the degree of conjugation between the central and donor moieties. The calculated fluorescence and trans-cis isomerization rates are in good agreement with the observed fluorescence quantum yields.

With the emergence of new VR/AR technologies, the question arises of how they can be used in human-swarm interaction. Where are the limitations and boundaries of conventional interfaces, and how can VR/AR overcome them? To find out, a user study was conducted. The subjects were able to interact with an autonomously acting swarm of drones using both a conventional desktop interface (Desktop-HSI) and a newly developed VR interface (VR-HSI).The resulting assessments are used as a basis for determining the extent to which this new technology can be applied in human-swarm interaction. The technical basis was an already tested simulation software that was expanded with a network interface to allow interacting with a drone swarm using connected HSIs (Human-Swarm Interfaces). Standardized communication was emphasized to enable the development of HSIs with different requirements. Specifically for this work, a VR-HSI was developed with Unity and a desktop-HSI with Java and their performance regarding human-swarm interaction was evaluated.

The multidisciplinary nature of the work required for research in the Covid-19 pandemic has created new challenges for health professionals in the battle against the virus. They need to be equipped with novel tools and resources ---that have emerged during the pandemic--- to gain access to breakthrough findings, know the latest developments, and to address their specific needs for rapid data acquisition, analysis, evaluation, and reporting. Because of the complex nature of the virus, the healthcare systems worldwide are severely impacted as the treatment and the vaccine for Covid-19 disease are not yet discovered. This leads to frequent changes in regulations and policies by governments and international organizations. Our analysis suggests that given the abundance of information sources, finding the most suitable tool for a given task is one of such challenges. But health professionals and policymakers need access to the most relevant, reliable, trusted, and latest information and tools that can be used in their day-to-day tasks of Covid-19 research and analysis. In this article, we present our analysis of various novel and important tools that have been specifically developed during the Covid-19 pandemic and that can be used by the health professionals community to help in advancing their analysis and research. These tools comprise of search engines, information repositories for literature and clinical trials, data sources, dashboards, and forecasting models. We present list of the minimally essential tools to serve a multitude of purposes, from hundreds of those developed since the beginning of the pandemic. A critical analysis is provided for the selected tools based on 17 parameters that can be useful for researchers and analysts for their evaluations. These parameters make up our evaluation framework and have not been used previously for analysis and evaluation. Hence, knowledge of the tools will not only increase the productivity but will also allow to explore new dimensions for using existing tools with more control, better management, and greater outcome of their research. In addition, the parameters used in our framework can be applied for future evaluations of similar tools and health professionals can adapt them for evaluation of other tools not covered in this analysis.

Intracortical microelectrode arrays (MEAs) can be used in a range of applications, from basic neuroscience research to providing an intimate interface with the brain as part of a Brain-Computer Interface (BCI) system aimed to restore function for people living with neurological disorders or injuries. Unfortunately, MEAs tend to fail prematurely, leading to a loss in functionality for many applications. An important contributing factor in MEA failure is oxidative stress resulting from chronically inflammatory-activated microglia and macrophages releasing reactive oxygen species (ROS) around the implant site. Antioxidants offer a means for mitigating oxidative stress and improving tissue health and MEA performance. Here, we investigate using the clinically available antioxidant dimethyl fumarate (DMF) to reduce the neuroinflammatory response and improve MEA performance in a rat MEA model. Daily treatment of DMF for 16 weeks resulted in a significant improvement in the recording capabilities of MEA devices during the sub-chronic (Weeks 5-11) phase (42% active electrode yield vs. 35% for control). However, these sub-chronic improvements were lost in the chronic implantation phase, as a more exacerbated neuroinflammatory response occurs in DMF-treated animals by 16 weeks post-implantation. Yet, neuroinflammation was indiscriminate between treatment and control groups during the sub-chronic phase. Although worse for chronic use, a temporary improvement (<12 weeks) in MEA performance is meaningful. Providing short-term improvement to MEA devices using DMF can allow for improved use for limited-duration studies. Further efforts should be taken to explore the mechanism behind a worsened neuroinflammatory response at the 16-week time point for DMF-treated animals to assess its usefulness to specific applications.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

Bovine tuberculosis (BTB) is endemic in Ethiopian cattle. BTB is caused by Mycobacterium bovis (M. bovis) and has economic and public health significance. which has significant impact on the health of livestock and human. It has been significantly a cause for great economic loss in animal production. Associated risk factors contributed to the prevalence of the disease in cattle and its transmission. Moreover, the majority of cattle owners lack awareness about the disease and its public health significance. The presence of multiple hosts including wild animals, inefficient diagnostic techniques, absence of defined national controls and eradication programs could impede the control of bovine TB. Awareness rising about the disease, its transmission andzoonotic implication however, in Ethiopia Bovine Tuberculosis in Human-Livestock-Wildlife Interface is not well studied in the country and there were no studies concerning the burden of the disease between human ,animal and wild life which is of great importance for reduction and control measures. This paper aims to review the potential health and economic impact of bovine tuberculosis control in order to safeguard human and animal population in Ethiopia

The dependence of longleaf pine (Pinus palustris) ecosystems on fire is well-understood, and anthropogenic alteration of fire cycles within its natural range has contributed to its decline. This is increasingly exacerbated in areas of urban interfaces, wherein use of prescribed fire can be problematic. The purpose of this study—the University of West Florida Campus Ecosystem Study—was to examine effects of fire exclusion on longleaf pine in the unique urban interface of a university campus. This was conceived as an interconnected series of investigations on the main campus and three associated natural areas that comprise remnant longleaf stands following cessation of widespread longleaf pine harvesting ~120 years ago. This period of chronic fire exclusion has allowed for a distinct shift in stand structure and composition. The open, savanna-like structure of fire-maintained longleaf stands has transitioned into closed-canopy forests with the increased prevalence of southern evergreen oaks (especially live oak—Quercus virginiana) and Magnolia spp., resulting in complete absence of longleaf regeneration. Fire exclusion has also appeared to have decreased soil fertility. Significant variation in mean age of longleaf pine stems of the main campus and natural areas suggest that the natural areas were likely under separate ownership with contrasting land-use history prior to purchase by the State of Florida for campus construction in 1963.

To improve the interfacial compatibility between cement matrix and expanded polystyrene (EPS) in the core-shell lightweight aggregates (CSLA), the effects of sodium silicate, Polyvinyl alcohol (PVA) emulsion, Vinyl acetate-ethylene (VAE) emulsion, acrylic acid, and acetic acid on the cement-EPS interface were investigated. The denseness of the interface was studied by scanning electron microscopy (SEM), and the effect of interfacial agents on the hydration process of cement was studied by the heat of hydration and induction resistivity. The macroscopic properties of the interface of the CSLA were characterized by the "leak-white" rate, drop resistance and numerical crushing strength. The results show that the sodium silicate densifies the interface by generating hydration products on the EPS surface. At the same time, organic acid enhances the interfacial properties of EPS and cement by increasing the surface roughness and allowing hydration products to grow in the surface micropores. In terms of the cement hydration process, both two interfacial agents delay the cement hydration. Above all, with comprehensive interface properties, "leak-white" rate, and mechanical properties, VAE emulsion and sodium silicate can achieve the best performance with a final crushing resistance of 5.7 MPa.

The environment impacts human health in profound ways, yet few theories define the form of the relationship between human physiology and the environment. Under current epidemiological constructs of causation, it is assumed that two complex systems (environment and humans) can transfer information directly. This is the underlying structure of the relationship when studies examine, for example, air pollution and brain health. In marked contrast, we conjecture that complex systems cannot interact directly, but rather such interaction requires the formation of an “interface”. Further, we contend that this dynamic, process-based interface incorporates components from all the interacting systems but exhibits operational independence. This property has many consequences, the foremost being that characteristics of the interface cannot be fully resolved by only studying the systems involved in the interaction. The interface itself must be the subject of inquiry. Without refocusing our attention on biodynamic interfaces, we cannot discern how our environment impacts health.

Silicone rubber formulations in the form of thin discs have been studied under room ambient conditions for their surface characteristics. The samples were silicone rubber manufactured in laboratory and those industrially manufactured. The measurements were done using an electrometer high resistance meter, applying dc voltage under normal room ambient conditions. The results show that the silicone rubber samples show higher values of surface resistivity when the dc voltage was applied. Silicone rubber samples manufactured in laboratory seem to exhibit erratic behaviour unlike their corresponding silicone rubbers manufactured in industry; this could be due to manufacturing shortcomings in laboratory and the irregularities in the way the silicone rubber adhered to the concentric ring electrodes. The empirical current traversing the surface of the silicone rubbers does not decay exponentially but rather it decays as an exponential power of the energization time.

The aerodynamic efficiency of a NACA 0012 AR 4 wing was affected through periodic contours aligned in the flow direction resembling a “wrinkled” texture. Streamwise and cross-stream Particle Image Velocimetry (PIV) were conducted at the University of Dayton Low Speed Wind Tunnel (UD-LSWT) around Reynolds number of 135,000 on the NACA 0012 AR 4 wing with and without surface contours. Wings with 6 contour sections was designed by spline fitting two NACA 0012 airfoil profiles in the spanwise direction. Both 2D (wall-to-wall model) configuration and 3D configuration of the wings were tested to determine the effects of surface contours on the parasite and induced drag of the wing. Streamwise PIV results indicated an increase in momentum deficit in the wake of the mid-contour region due to enhanced boundary layer separation from the upper surface of the mid-contour region. The cross-stream PIV results indicated a decrease in the magnitude of azimuthal velocity, circulation and RMS quantities in the wingtip vortex with the surface contours. The reduction in the wingtip vortex properties indicates that the contours were effective in blocking the spanwise flow feeding into the wingtip vortex on the surface of the wing

BiFeO3/La0.7Sr0.3MnO3 (BFO/LSMO) epitaxial heterostructures were successfully synthesized by pulsed laser deposition on (001)-oriented SrTiO3 single crystal substrates with Au top electrodes. Stable bipolar resistive switching characteristics regulated by ferroelectric polarization reversal was observed in the Au/BFO/LSMO heterostructures. The conduction mechanism was revealed to follow the Schottky emission model, and the Schottky barriers in high resistance and low resistance states were estimated based on temperature-dependent current–voltage curves. Further, the observed memristive behavior was interpreted via the modulation effect on the depletion region width and the Schottky barrier height caused by ferroelectric polarization reversal, combining with the oxygen vacancies migration near the BFO/LSMO interface.

Alternating TiB2-dcMS and Cr-HiPIMS layers are used to fabricate TiB2/Cr multilayer films. In-troducing a 5-nm-thick Cr interlayer deposited under a substrate bias of -60 V produces slight increases of both film hardness and elastic modulus. The TEM observation indicates that the Cr grains favor epitaxially growth on TiB2 interlayer, forming a coherent TiB2/Cr interface. This produces the hardness increasement. Mechanic measurement by using AFM illustrates that the coherent interface increases the elastic modulus of the Cr up to ~280 GPa, which is significantly higher than bulk material.

With the rapid development of MEMS (Micro-electro-mechanical Systems) fabrication technologies, manifolds microelectrodes with various structures and functions have been designed and fabricated for applications in biomedical research, diagnosis and treatment through electrical stimulation and electrophysiological signal recording. The flexible MEMS microelectrodes exhibit multi-aspect excellent characteristics beyond stiff microelectrodes based on silicon or SU-8, which comprising: lighter weight, smaller volume, better conforming to neural tissue and lower fabrication cost. In this paper, we mainly reviewed key technologies on flexible MEMS microelectrodes for neural interface in recent years, including: design and fabrication technology, flexible MEMS microelectrodes with fluidic channels and electrode-tissue interface modification technology for performance improvement. Furthermore, the future directions of flexible MEMS microelectrodes for neural interface were described including transparent and stretchable microelectrodes integrated with multi-aspect functions and next-generation electrode-tissue interface modifications facilitated electrode efficacy and safety during implantation. Finally, the combinations among micro fabrication techniques with biomedical engineering and nanotechnology represented by flexible MEMS microelectrodes for neural interface will open a new gate to human lives and understanding of the world.

Background: The standard surgical approach to amputation has failed to evolve significantly over the past century. Consequently, standard amputations often fall short with regards to improving the quality-of-life (QoL) for patients. A modified amputation has been designed at both the transtibial (TTA) and transfemoral (TFA) level that incorporates agonist-antagonist myoneural interface (AMI) constructs to provide patients with a novel alternative to standard amputation. Here, we present the patient reported outcome measures (PROMs) amongst our lower extremity AMI amputees and demonstrate an overall significant improvement in their physical and mental wellbeing. Methods: Four PROMs surveys, 1) EQ-5D-3L, 2) Lower Extremity Functional Scale (LEFS), 3) PROMIS-57, 4) Short Form-36 (SF-36), and 5) Sickness Impact Profile (SIP), were administered to lower extremity AMI amputees pre-operatively (baseline) and at 6 weeks, 3 months, 6 months, 9 months, 12 months, 24 months, 36 months, and 48 months post-operatively between June 24th, 2018, and December 15th, 2022. The surveys were either administered during a clinic visit or emailed at the encounter timepoint. Study data was collected and managed using REDCap (Research Electronic Data Capture) electronic data capture tools hosted at Brigham and Women’s Hospital. Analyses of collated data were performed by fitting a linear mixed model using SAS version 9.4 (SAS Institute, Cary, NC). Results: The cohort’s baseline and 12-month post-operative responses were compared to determine score improvement. The cohort demonstrated a significantly improved EQ-5D-3L index value (p<0.0001) and EQ VAS (p<0.0001) at 12-months post-operatively (n=22) when compared to baseline (n=28). The LEFS score significantly improved at 12-months post-operatively compared to baseline (p<0.0001) with a mean of 59.04 ± 3.14 (SE) at 12-months and a mean of 31.96 ± 2.84 (SE) at baseline. AMI patients demonstrated significantly improved scores across PROMIS-57 domains at 12-months compared to baseline scores; the p-value was <0.0001 for all domains except for the Depression domain where p=0.0181. The health domain scores significantly improved from baseline to 12-months post-operation for all SF-36 domains. Lastly, the SIP indicated a significant decrease in overall dysfunction from baseline to 12-months post-operation (p<0.0001). Conclusions: Modified lower extremity amputation with AMI construction has the potential to provide amputees with increased quality-of-life when compared to the pre-operative state. However, further investigation is necessary to determine whether the patient reported outcome measures of the AMI amputee cohort are superior to those who receive a standard amputation.

This study provides, to our knowledge, the first detailed analysis of how surface oil modifies air-sea interaction in a two-way coupled model, i.e., the coupled-ocean-atmosphere-wave-sediment-transport (COAWST) model modified to account for oil-related changes to air-sea fluxes. This study investigates the effects of oil on surface roughness, surface wind, surface and near surface temperature differences, and boundary-layer stability, and how those conditions ultimately affect surface stress. We first conducted twin coupled modeling simulations with and without the influence of oil over the Deepwater Horizon (DWH) oil spill period (April 21 to May 5, 2010) in the Gulf of Mexico. Then we compared the results by using a modularized flux model with parameterizations selected to match those selected in the coupled model adapted to either ignore or account for different atmospheric/oceanic processes in calculating surface stress. When non-oil inputs to the bulk formula treated as unchanged by oil, the surface stress changes are always negative due to oil-related damping of surface roughness alone. However, the oil-related changes to 10-m wind speed and boundary-layer stability are found to play a dominant role in surface stress changes relative to those due to the oil-related surface roughness changes, highlighting that most of the changes in surface stress are due to the oil-related changes in wind speed and boundary-layer stability. Finally, the oil-related changes to surface stress due to the combined oil-related changes in surface roughness, surface wind, and boundary-layer stability are not large enough to have a major impact on the surface current and surface oil transport, indicating that the feedbacks from the surface oil to the surface oil movement itself are minor for forecasting the surface oil transport unless the fractional oil coverage is much larger than found in this study.

When using computer-aided translation systems in a typical, professional translation workflow, there are several stages at which there is room for improvement. The SCATE (Smart Computer-Aided Translation Environment) project investigated several of these aspects, both from a human-computer interaction point of view, as well as from a purely technological side. This paper describes the SCATE research with respect to improved fuzzy matching, parallel treebanks, the integration of translation memories with machine translation, quality estimation, terminology extraction from comparable texts, the use of speech recognition in the translation process, and human computer interaction and interface design for the professional translation environment. For each of these topics, we describe the experiments we performed and the conclusions drawn, providing an overview of the highlights of the entire SCATE project.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

This paper studied the dynamic characteristics of the deployment process of the replaceable interface mast and the vibration generated at the end of the mast. The interface is discretized by the absolute nodal coordinate thin shell element with gradient reduction, and the three-dimensional motion of the reconfigurable rigid body module is described by the natural coordinate method. The dynamic equations of the interface and the reconfigurable module without external constraints are established by the principle of virtual work. Finally, the dynamic models of each part are assembled into the dynamic model of the mast system deployment process through the system constraint equation. According to the established dynamic model of the mast system deployment process, the dynamic behavior changes of the replaceable interface mast are analyzed. At the same time, the differences in the deployment behavior of the replaceable interface mast under different system configuration schemes, flexible interface geometric parameters, and different driving laws are studied and compared. It provides guidance for the scheme configuration of the mast system, the structural design of the interface, and the deployment motion planning of the mast. According to the physical prototype and the assembly of the mast system model, the deployment process of the replaceable interface mast is experimentally analyzed. It shows that the established dynamic model of the mast system can correctly analyze the dynamic characteristics of the deployment behavior of the replaceable interface mast, which provides a reference for the design and behavior analysis of the mast system.

Intracortical microelectrodes that can be implanted have the ability to capture fast-changing neuron action potentials in the living brain. Despite this potential, many obstacles must still be overcome for reliable, long-term, high-quality recordings and accurate analysis of brain activity. These challenges include improving recording quality, enhancing recording stability, increasing recording capacity, and adding multi-functional features. One potential approach to enhance implantable microelectrodes involves the advancement of materials, refinement of implantation methodologies, and augmentation of the number of sites for recording. However, these challenges are still being actively researched, and advancements in microelectrode technology are underway. The difficulties with implantable microelectrodes are evaluated, and solutions are presented from different perspectives. The latest advancements in microelectrode technology are reviewed and condensed, and future possibilities are explored.

Aiming at the problems that the parameters of YOLOv5s model are too large and the computing resources of development board memory are limited, a new target detection method based on deep learning YOLOv5 algorithm model is proposed. First, the light-weight module Gz-ShffleNetv2 is used to construct cotton top bud feature extraction unit, which reduces the number of parameters and improves the running speed. It can be better applied in image classification, speed up detection and meet the requirements of mobile end of development board. Secondly, in order to solve the problem of decreasing detection accuracy caused by lightweight, BotNet and C3SE attention mechanism are added to focus on specific areas of cotton terminal bud. Combined with YYG loss function XIOU boundary frame regression loss, more feature information and rich feature MAP were obtained to further improve the accuracy of target detection. Through analysis of research and experimental results, the average accuracy map reached 91.3% under the Windos system NVIDIA Geforce RTX 2060 SUPER detection. While maintaining high precision identification, the number of parameters of YOLOv6 and YOLOv7-tiny network model is reduced by 83% and 53%, respectively, and the detection accuracy is increased by 1.2% and 7.7%, respectively. Compared with YOLOv5 reasoning image, the speed of image is increased by 0.035s, and the detection accuracy of MAP_0.5:0.95 is increased by 1%. At the same time, PyQt5 and YOLOv5 target detection algorithms are used to design a cotton top bud identification system, which makes cotton top bud detection more intuitive and convenient for subsequent hardware development and use.

A novel phase-field method based numerical approach to modeling the compaction process of sedi- ments is presented. Water-logged rock or soil sediments are deposited on the water basins over time and the increasing volume of the sediment compacts under its own weight and external pressure. Coupled evolution of mass conservation, Darcy flow, and the viscoelastic constitutive response, in conjunction with the evolution of porosity and permeability, make this problem highly non-linear and involve moving boundaries. We adopt a phase-field approach to represent the moving sediment interface, and the underlying multiphasic model permits for studying compaction in dynamically evolving sediments. This approach does not necessitate a change of domain sizes as is the case of existing traditional models of sedimentation but rather treats sedimentation growth as a problem of interface motion. We first model a classical compaction problem in 1D to compare with existing results in the literature, and then extend the framework to 2D to model the compaction process taking place under the influence of gravity. The model is then extensively applied to understand the effect of the sediment initial state and the sediment material properties on the compaction process and its spatiotemporal evolution. Lastly, a strong validation of our phase-field treatment results against predictions from traditional methods of solving open boundary sediment compaction problems, and a good agreement between the conventional understanding and the numerical predictions of porosity dependence on the fluid pore pressure for various cases of geological interest, are used to demonstrate the applicability and scalability of this novel numerical framework to model more advanced sediment compaction problems and geometries.

Uncontrollable Zn dendrite formations and parasitic side reactions on Zn electrodes induce poor cycling stability and safety issues, preventing the large-scale commercialization of Zn-ion batteries. Herein, to achieve uniform Zn deposition and suppress side reactions, an electrospun ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) copolymer, a [P(VDF-TrFE)] nanofiber layer, is introduced as an artificial solid-electrolyte interface on a Cu substrate acting as a current collector. The aligned molecular structure of β-P(VDF-TrFE) can effectively suppress localized current density on the Cu surface, lead to uniform Zn deposition, and suppress side reactions by preventing direct contact between electrodes and aqueous electrolytes. The half-cell configuration formed by the newly fabricated electrode can achieve an average coulombic efficiency of 99.2% over 300 cycles without short circuiting at a current density of 1 mA cm-2 and areal capacity of 1 mAh cm-2. Stable cycling stability is also maintained for 200 cycles at a current density of 0.5 A g-1 in a full-cell test using MnO2 as a cathode.

This paper is focused on understanding multiscale modelling to obtain a bridge among different time and length scales of simulation techniques. These techniques are vital as it holds the potential to understand and predict the capabilities of polymer nanocomposites (PNCs). However, an appropriate approach in controlling the interfacial interaction between nanoparticle and polymer in nanocomposites structure is still needed to develop. In this review, an initial brief introduction to various trending simulation techniques has been discussed at all three levels of scale (nm, μm, mm). Later, descriptive study on fundamental issues such as thermodynamics, kinetics, mechanical properties, and morphology has been studied deeply. The multiscale modeling bridges the gaps of simulation between the different scales of models from molecular to mesoscale levels working over the broad range of length and timescale. Through the sequential, adaptive, and concurrent approaches, we can develop a system that may comprehend multiscale mode modeling adaptive resolution approach has recently added approach the molecule of the subject can shift their position freely in the domain and through this approach and studied the Brownian motion. Co-The co-current coach is also termed as handshaking path and it is linked aiming at different scale models. Covering the rigid techniques smoothly and linking them at different scales helps in normalizing the statistical behaviour.

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

In this paper, by developing a mathematical model, the operating temperature of perovskite solar cells (PSCs) under different operating conditions has been calculated. It is found that by reducing the density of tail states at the interfaces, acting as recombination centres, through some passivation mechanisms, the operating temperature can be reduced significantly at higher applied voltages. The results show that if the density of tail states at the interfaces is reduced by three orders of magnitude through some passivation mechanisms, then the active layer may not undergo any phase change up to an ambient temperature 300 K and it may not degrade up to 320 K. The calculated heat generation at the interfaces at different applied voltages with and without passivation shows that the heat generation can be reduced by passivating the interfaces. It is expected that this study may provide a deeper understanding of the influence of interface passivation on the operating temperature of PSCs.

Various methods of polymer surface tailoring have been studied to control the changes in wetting behavior. Polymers having precisely controlled wetting behavior in a specific environment are blessed with a wealth of opportunities and potential applications exploitable in biomaterial engineering. The controlled wetting behavior can be obtained by combining surface chemistry and morphology. Plasma assisted polymer surface modification technique have played a significant part to control surface chemistry and morphology. This review focuses on plasma polymerization and investigations regarding surface chemistry, surface wettability, coating kinetics, as well as coating stability. We begin with brief overview of plasma polymerization; these include growth mechanisms of plasma polymerization and influence of plasma parameters. Next, surface wettability and theoretical background structures and chemistry of superhydrophobic and superhydrophilic surfaces. In this review, overview of recent work on tunable wettability by tailoring surface chemistry and physical appearance (i.e. substrate texture) is also described. The formation of smart polymer coatings, which adjust their surface wettability by according to outside environment, including, pH, light, electric field and temperature. Finally, the applications of tunable wettability and pH responsiveness of polymer coatings in real life are addressed. This review should be of interest to plasma surface science communality specifically focused controlled wettability of smart polymer surfaces.

In this study, the NiCrAlY coating was prepared using the atmospheric plasma spraying (APS). The sample was then exposed to a continuous fiber laser beam. Laser surface melting (LSM) can effectively homogenize the composition of the coating. It also reduced the defects and roughness. The coating was examined using optical microscopy (OM), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The process parameters of the LSM consist of laser power and scan rate. The high-temperature oxidation test was conducted for 200 hours at a temperature of 1100 °C. After a period of 200 hours, the primary coating demonstrated the emergence of an aluminum oxide layer, along with the presence of harmful spinel oxides. The laser remelting technique was used to modify the surface, which led to the uniform growth and development of an aluminum oxide layer (α-Al₂O₃) during the oxidation examination. Therefore, it appears that the reduction in grain size caused by laser remelting prevents the wrinkling of Al2O3 oxide. This process represents a novel and alternative approach to modifying MCrAlY coatings.

Automation is the key aspect of science and technology field and refers to controlling the systems for efficient output requirements. The development of robotics and similar, technologies in 21st century is a vast topic of research and significant progress has been made on this field. This research study focuses on building a ribbon-cutting robot with a Bluetooth interface for event inaugurations. The entire system hinges on constructing a prototype that is mounted on a robotic car frame with four wheels and an Arduino controller. In this case, ribbons are cut using a nickel wire, and it may be paired with an Android device via Bluetooth or an application. The robot is one of the first steps toward the development of autonomous, cognitive robots and can be used in a variety of events. Efficient temperature monitoring is done with help of LM35 sensor and Bluetooth based communication in order to monitor the conditions and effectively control the actions for which robot is designed. The robot has significantly allowed authors for desired tests on ribbon cutting and final results obtained were very exciting for its desired application target. Ribbon-cutting robots find applications in various events, including inaugurations, exhibitions, and ceremonies. Their precision and novelty add value to such occasions.

In the pursuit of energy-efficient spiking neural network (SNN) hardware, synaptic devices lev-eraging emerging memory technologies hold significant promise. This study investigates the ap-plication of the recently proposed HfO2/SiO2-based interface dipole modulation (IDM) memory for synaptic spike timing-dependent plasticity (STDP) learning. Firstly, through pulse measure-ments of IDM metal-oxide-semiconductor (MOS) capacitors, we demonstrate that IDM exhibits an inherently nonlinear and near-symmetric response. Secondly, we discuss the drain current re-sponse of a field-effect transistor (FET) incorporating a multi-stack IDM structure, revealing its nonlinear and asymmetric pulse response, and suggest that the degree of the asymmetry depends on the modulation current ratio. Thirdly, to emulate synaptic STDP behavior, we implement dou-ble-pulse-controlled drain current modulation of IDMFET using a simple bipolar rectangular pulse. Additionally, we propose a double-pulse-controlled synaptic depression that is valuable for optimizing STDP-based unsupervised learning. Integrating the pulse response characteristics of IDMFETs into a two-layer SNN system for synaptic weight updates, we assess training and classification performance on handwritten digits. Our results demonstrate that ID-MFET-based synaptic devices can achieve classification accuracy comparable to previously re-ported simulation-based results.

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

The feet cannot perform tasks as quickly and with as much dexterity as the hands. However, due to the heavy workload placed on the hands, there is potential for the feet to replace or assist the hands. In order to use the feet more effectively, this study aims to find ways to increase the speed and accuracy of directly touching a touchpad with the feet while in a seated position. The study investigates the effects of three factors: the slope of the touchpad, the direction of foot movement, and the touch area of the foot used. Regarding the direction of foot movement, the study found that the most effective direction for both accuracy and speed was at a 30-degree angle to the right when the front of the right foot was set at 0 degrees. The 0-degree and 60-degree angles showed similar efficiencies, but were lower than the 30-degree angle. The study also found that using the big toe as the touch area resulted in the best speed, accuracy, and subjective satisfaction. The index toe was the second-best option, while using the ball of the foot was the least accurate and slowest option. Lastly, using an slope angle of 15 degrees for the touchpad was found to increase work efficiency compared to using a 7-degree slope angle. These findings can serve as guidelines for designing foot interfaces.

Background: There is an increasing interest in the role of EEG in neurorehabilitation. We primarily aimed to identify the knowledge base through highly influential studies. Our secondary aims were to imprint the relevant thematic hotspots, research trends, and social networks within the scientific community. Methods: We performed an electronic search in Scopus looking for studies reporting on rehabilitation in patients with neurological disabilities. The most influential papers outlined the knowledge base, while a word co-occurrence analysis imprinted the research hotspots. Likewise, co-citation analyses highlighted collaboration networks between Universities, authors, and countries. The results were presented in summary tables, burst detection plots, and geospatial maps. Finally, a content review based on the top-20 most cited articles completed our study. Results: Our current bibliometric study was based on 874 records from 420 sources. There was a vivid research interest in EEG use for neurorehabilitation, with an annual growth rate as high as 14.3%. The most influential paper was the study titled "Brain-computer interfaces, a review" by Nicolas-Alfonso LF and Gomez-Gill J, with 997 citations, followed by "Brain-computer interfaces in neurological rehabilitation" by Daly J. and Wolpaw JR (708 citations). The USA, Italy, and Germany were among the most productive countries. The research hotspots shifted with time from the use of “functional magnetic imaging” to EEG-based “brain-machine interface”, “motor imagery”, and “deep learning”. Conclusions: EEG constitutes the most significant input in brain-computer interfaces (BCI) and can be successfully used in the neurorehabilitation of patients with stroke, amyotrophic lateral sclerosis, and traumatic brain and spinal injury. EEG-based BCI facilitates training, communication, and control of wheelchair and exoskeletons. However, research is limited to specific scientific groups from developed countries. Evidence is expected to change with the broader availability of BCI and improvement in EEG filtering algorithms.

Objective A trained T1 class Convolutional Neural Network (CNN) model will be used to examine its ability to successfully identify motor imagery when fed pre-processed electroencephalography (EEG) data. In theory, and if the model has been trained accurately, it should be able to identify a class and label it accordingly. The CNN model will then be restored and used to try and identify the same class of motor imagery data using much smaller sampled data in an attempt to simulate live data. Approach PyCharm, a Python platform, will be used to house and process the CNN. The raw data used for the training of the CNN will be sourced from the PhysioBank website. The EEG signal data will then be pre-processed using Brainstorm software that is a toolbox used in conjunction with MATLAB. The sample data used to validate and test the trained CNN, will be also be extracted from Brainstorm but in a much smaller size compared to the training data which is comprised of thousands of images. The sample size would be comparable to a person wearing a Brain Computer Interface (BCI), offering approximately 20 seconds of motor imagery signal data. Results The raw EEG data was successfully extracted and pre-processed. The deep learning model was trained using the extracted image data along with their corresponding labels. After training, it was able to accurately identify the T1 class label at 100 percent. The python coding was then modified to restore the trained model and feed it test sample data in which it was found to recognise 6 out of 10 lines of T1 signal image data. The result suggested that the initial training of the model required a different, more varying approach, so that it would be able to detect varying sample signal image data. The outcome of which could mean that the model could be used in applications for multiple patients wearing the same BCI hardware to control a device or interface.

Recent progress in microfabrication technique allowed the rapid development of neural implants. They are getting categorized as effective tools for clinical practice, especially to treat traumatic and neurodegenerative disorders. Microelectrode arrays already have been used in numerous neural interface devices. Basically, almost all neural implants have been developed based on BCI (Brain Computer Interface) system. When BCI system falls under invasive technique, it is referred as BMI or Brain Machine Interface. BMIs hold promises for neurorehabilitation of motor and sensory function, cognitive state evaluation and treatment of neurological chaos. A directed overview of the field of neural implants is discussed in this article. The aim of this review is to give a brief introduction of neural prosthetics as well as their exciting applications in treating neurological disorders and a deep discussion on their functionality are mentioned. BCI system and their different types, their functionality, their pros and cons, how other neural implants developed, and their present status have been covered. Different possibilities and possible future of deep brain stimulation (DBS), Neuralink, motor and sensory neural prosthetics are further discussed.

Direct interaction with the neuronal cells is a prerequisite to deciphering useful information in understanding the underlying causes of diseases and functional abnormalities in the brain. Precisely fabricated nanoelectrodes provide the capability to interact with the brain in its natural habitat without compromising its functional integrity. Considerable research has been focused on the employment of vertical nanotubes as nanoelectrodes due to large-scale intracellular recording capability and longer-term intracellular access that arise from their unique geometry. Despite many types of nanotube structures reported in the literature, a limited subset of the nanotubes has been investigated for neural interfacing. This work reports on the fabrication and optimisation of vertically oriented titania nanotube arrays as a scalable electrode platform for neural interface application. To this end, the doping was performed by incorporating a selected group of biologically active metallic ions, including zinc, strontium, and copper, into TiO2 lattice and its effect was studied with respect to the structural, electrochemical and biological properties of the nanotube arrays. It was found that doping can change the length, diameter and wall thickness of the nanotubes. Among pure and doped samples, the copper-doped TiO2 nanotubes demonstrated the highest electrochemical and biological performance. Our results suggest that the doping can be used as a promising method to optimise the properties of nanotube arrays for the development of high-performance neural electrodes.

FPGA-based data acquisition and processing systems play an important role in modern high-speed, multichannel measurement systems, especially in High-Energy and Plasma Physics. Such FPGA-based systems require an extended control and diagnostics part corresponding to the complexity of the controlled system. Managing the complex structure of registers while keeping the tight coupling between hardware and software is a tedious and potentially error-prone process. Various existing solutions aimed at helping that task do not perfectly match all specific requirements of that application area. The paper presents a new solution based on the XML system description, facilitating the automated generation of the control system’s HDL code and software components and enabling easy integration with the control software. The emphasis is put on reusability, ease of maintenance in case of system modification, easy detection of mistakes, and the possibility of use in modern FPGAs. The presented system has been successfully used in data acquisition and preprocessing projects in High-Energy Physics experiments. It enables easy creation and modification of the control system definition and convenient access to the control and diagnostic blocks. The presented system is an open-source solution and may be adopted by the user for particular needs.

In this paper, the nanoscale dissipative mechanisms of a Cu pad in a Ball Grid Array (BGA) packaging structure during isothermal ageing and uniaxial tension were investigated by the molecular dynamics (MD) method and experiments. From the result of the isothermal ageing test, a nonuniform consumption of Cu and large amount of Kirkendall voids were observed at the interface of Cu and Cu₃Sn. To study the effect of pressure and orientation on this phenomenon, MD simulations were conducted on four types of Cu-Cu₃Sn interface structures with different orientations of Cu. By comparing the diffusion coefficients of atoms in those cases, it was found that the tensile stress would inhibit the diffusion of atoms, whereas compressive stress would accelerate it, and this would be more significant under a larger magnitude of stress and temperature. Note that, in the model with the (101) surface Cu at the interface, both Cu and Cu₃Sn have a higher diffusion coefficient compared with the model with (001) surface Cu. Thus, the orientation of Cu will also contribute to the uniform consumption of the pad. Uniaxial tension simulation combined with DXA and CSP analyses on those models also shows the model with (001) surface Cu has a greater mechanical reliability in our simulations and related experiments.

Interface between matrix/coating or coating/coating in fact represents a very complicate thin interfacial layer. So interface model is necessary to avoid the difficulty on considering such a complicate thin layer in analysis. Classic interface model and cohesive model have been widely used in stress analysis of coating materials, though they cannot represent the effect of very thin interfacial layer accurately. A complete interface model has been deduced from the equivalent constitutive of interfacial layer in this paper. It is found that both classic interface model and cohesive model sometimes cannot give correct analysis results, while the complete interface model can always give a correct result. Moreover, the stress parallel to interface within the interfacial layer can also be analyzed by the new model. Besides, this model can also be used to describe the equivalent properties of interfacial layer, thereby, can provide a quantitative characterizing method for interfacial layer itself.

S-licarbazepine was prepared by asymmetric reduction of oxcarbazepine with interface-assembled carbonyl reductase at the interface of oil/water biphasic system. The carbonyl reductase was conjugated with polystyrene in the surface of toluene/Tris-HCl biphasic system and formed a surfactant-like structure. The conversion and enantiometric excess of S-licarbazepine reached 97.39% and 99.6% when 3.97 mmol/L oxcarbazepine was reduced by interface-assembled carbonyl reductase with 60 g/L ethanol as co-substrate in toluene/Tris-HCl(12.5:10) biphasic system at 30 °C, 180 rpm for 6 h.

A single mode waveguide grating coupler based on multiple Si-SiO₂ pairs onto Si substrate has been designed. Numerical analysis has been carried out to calculate optimum thickness of the layers of Si-SiO₂ that ensures the constructive interference between reflected waves and actual guided wave for high coupling efficiency. Based on the results, an optimal design is developed and modeled by using a 2-D finite difference time domain (2-D FDTD) simulator that dictates a coupling efficiency of as much as 78% (-1.07 dB) at the wavelength of 1550 nm, and a 1-dB bandwidth of 77 nm. The numerical method will be useful to calculate the optimum thicknesses of the layers for any reflector based grating coupler of different materials.

The development of sensitive and specific exosome detection devices is highly desirable because it is believed to deliver specific important information for cancer screening, diagnosis, and monitoring. Among many detection techniques, nanoplasmonic sensors are optical detection methods that offer advantages in sensitivity and detection speed and this makes the sample analysis process faster and more accurate. This paper summarizes the development of nanoplasmonic biosensors, especially Surface Plasmon Resonance (SPR) and Localized Surface Plasmon Resonance (LSPR)-based biosensors for exosome detection. There are three main parts in this paper. The first part will focus on introducing the theoretical background regarding the working principles of SPR and LSPR biosensors. After that, we will introduce several methods that can be used for exosome isolation. This article will close by explaining the engineering of nanoplasmonic sensors both in terms of transducer modification to amplify the signal and functionalization strategies to increase sensor specificity. In this section, the detection mechanism, the type of exosomes detected, and the resulting detection limits are some of the points highlighted in this paper.

We report on a 2D-gap surface plasmon metasurface based composed of a bottom metal layer, middle insulator layer, and top metal nanostructure of gold nanoblocks (nanoantennas). The proposed structure enables us to generate simultaneous multi plasmonic resonances and offers the possibility to tune them, within the near-infrared domain. The simplicity of the metasurface makes it promising for compact optical platforms based on reflection mode operation with potential application in multi-channel biosensors, second-harmonic generation, and multi-wavelength surface-enhanced spectroscopy among other interesting fields

Integrating voice assistant technology can potentially enhance accessibility and user interaction in web-based platforms for geospatial data visualisation and processing. This paper presents an open-source development incorporating a voice virtual assistant into the BStreams web application platform, designed specifically for visualising geospatial data. The study aimed to mitigate the observed limitations of virtual assistants in understanding the semantics and context of user commands in the geospatial domain. A discourse framework specialised for geospatial data was developed using a structured prototype methodology. In addition, a survey assisted in identifying commonly used English terminologies for geospatial data interaction. The questionnaire results were subsequently assessed using the ChatGPT natural language processing model. The application used open-source frameworks, including Web Speech API, Leaflet, Mapbox geocoding, and JavaScript. This investigation indicates that voice virtual assistants can potentially enhance human-computer interaction for geospatial data visualisation and processing. However, challenges related to natural language understanding, accents, and domain knowledge were raised. The paper advocates for further research to refine the integration of voice technology in this domain.

Studying the interaction between the upper ocean and the typhoons is crucial to improve our understanding of heat and momentum exchange between the ocean and the atmosphere. In recent years, the upper ocean responses to typhoons have received considerable attention. The sea surface cooling (SSC) process has been repeatedly discussed. In the present work, case studies were examined on five strong and super typhoons that occurred in 2016—LionRock, 1610; Meranti, 1614; Malakas, 1616; Megi, 1617; and Chaba 1618—to search for more evidence and new features of typhoon’s impact on the sea surface environment. The typhoon monitoring data from the Central Meteorological Observatory, the sea surface temperature (SST) data from satellite microwave and infrared remote sensing, and the sea surface height anomaly (SSHA) data from satellite altimeters were used to analyze in detail: the SSC features caused by typhoons, the relationship between the SSC and the typhoon travelling speed, and the variations in cold and warm eddies during typhoon passage. Results showed that: (1) SSC generally occurred during typhoon passage and the degree of SSC was always determined by the strength and the travelling speed of the typhoon, as well as the initial SST. (2) One day before or on the day of typhoon passage, the SSHA slightly increased due to low surface pressure. After the typhoon passed, the SSHA obviously decreased along with the SSC. The pre-existing positive SSHAs, which always represent warm eddies, decreased or disappeared during typhoon passage, whereas negative SSHAs or cold eddies were enhanced. (3) New cold eddies were generated, especially at the turning points of the typhoon path. The presence of warm eddies is suggested to have a strengthening effect on the typhoons.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

The Brain-Computer Interface (BCI) technology has emerged as a groundbreaking innovation with profound implications across diverse domains, particularly in healthcare. By establishing a direct communication pathway between the human brain and external devices, BCI systems offer unprecedented opportunities for diagnosis, treatment, and rehabilitation, thereby reshaping the landscape of medical practice. However, despite its immense potential, the widespread adoption of BCI technology in clinical settings faces several challenges. These include the need for robust signal acquisition and processing techniques, ensuring user safety and privacy, addressing ethical considerations, and optimizing user training and adaptation. Overcoming these challenges is crucial to unleashing the complete potential of BCI technology in healthcare and realizing its promise of personalized, patient-centric care. This review work underscores the transformative potential of BCI technology in revolutionizing medical practice. This paper offers a comprehensive analysis of medical-oriented BCI applications by exploring the various uses of BCI technology and its potential to transform patient care.

The purpose of this study is to ​​explore the use of a custom Transformer model in brain-computer interfaces (BCIs) that translate the neural activity present when an individual with limited verbal and fine-motor skills attempts to handwrite. As found in previous studies, Transformers have performed better than recurrent neural networks (RNNs) in translation tasks which are similar to its usage here in decoding neural signals into intended handwritten text. Due to the known benefits of a Transformer, the hypothesis was that the Transformer would show promise in the context of a BCI through the recorded metrics. The neural signals of a tetraplegic individual, when they attempted to handwrite, were provided by existing research. Four trials were conducted using data with or without augmentation which the model used when training to separately minimize training loss and validation loss. When comparing the results of a BCI with the implementation of a Transformer model with the original RNN BCI (the original data source), the Transformer model performed less favorably across all four trials. Although the results do not indicate that the Transformer model currently outperforms an RNN BCI, it is important to note that further testing of the model's capabilities (such as training it with a larger and more preferable dataset and/or for longer, comparing training times between the RNN and Transformer, and/or seeing how the Transformer is improved with an offline autocorrect feature) is necessary before determining whether Transformers can enhance communication in this manner.

Two-dimensional (2D) semiconductors like Transitional Metal Dichalcogenides (TMDCs) have attracted strong research interest in the last decade. Unlike the more celebrated 2D material graphene, TMDCs like molybdenum disulfide(MoS₂) possess bandgap. The number of layers critically depends on the band structure of MoS₂. For example, it is indirect for bulk MoS₂. However, it becomes direct bandgap material for a monolayer MoS₂. Monolayer MoS₂, therefore, becomes an important material for photoelectronic devices. An essential aspect of such devices is the metal-semiconductor junction. Metal-TMDC junction is, therefore, a well-studied interface due to its importance for 2D materials-based photoelectronic devices. Most importantly, it can be flexible, stretchable to it’s length, and bent to a large angle. We used metals like Au and Al to interface with TMDs like MoS₂. We used silicon and PDMS as substrates. So, we have to focus on investigating the relative properties of various TMDCs. We see change in band energy and vibrational modes via Photoluminiscence and Raman spectroscopy as shown in the article. However, certain aspects are yet to be explored, for example, how this interface behaves in the presence of strain.

The recognition of coal-rock interface is very crucial for the research in the intelligent production of coal mine. This study investigates the application of terahertz time-domain spectroscopy in the recognition of coal-rock interface, including the identification of coal-rock and coal-rock mixtures, as well as the accurate characterization of coal seam thickness. Terahertz detection was used to obtain the optical parameter information of the pressed pellets prepared by mixing two different kinds of coal and two kinds of rock. Based on the experiment results, the database was established for the identification of coal-rock interfaces in coal mining machines. The terahertz detection was performed on 10 different kinds of sheet anthracite with different thickness, and the terahertz spectra of coal seams with different thickness were simulated and calculated by using simulation software, which can accurately obtain the thickness of coal seams and provide effective mining thickness parameters for coal seam mining. Through the experiment and simulation, the terahertz time-domain spectroscopy technology has a promising application prospect in the identification of coal-rock interface.

A single paragraph of about 200 words maximum. Electroencephalography (EEG) accumulates the electrical activities of human brain. It is an easy and cost effective tool to characterize motor imagery (MI) task used in brain computer interface (BCI) implementation. The MI task is represented by short time trial of multichannel EEG. In this paper, the raw EEG is decomposed into a finite set of narrowband signals obtained from individual EEG channels using Fourier transformation based bandpass filter. Each of the subband signals represents narrowband rhythmic components which characterize the brain activities related to motor imagery. The subband signals are arranged to extent the dimension of EEG trial in spatial domain. The spatial features are extracted from the set of extended trials using common spatial pattern (CSP). An optimum number of features are used to classify the motor imagery tasks represented by EEG trials. Artificial neural network is used to classify MI tasks. The performance of the proposed method is evaluated using two publicly available benchmark datasets. The experimental results show that it performs better than the recently developed algorithms.

Previous research via cell experiments has shown that ultrafine particles (UFPs, particles less than 100 nm) emitted from Three-Dimensional desktop printers (3D printers) had cytotoxicity. However, a few particles from different filaments and their cytotoxicity combinations have been tested. Here we quantify emissions of UFPs and use Air-Liquid Interface (ALI) from one commercially available filament extrusion desktop 3D printer utilizing three different filaments by controlled experiments. A549 cells were exposed at the ALI to UFPs generated by a working 3D printer for an average of 45 minutes and 90 minutes. Twenty-four hours after exposure, cells were analyzed for percent cytotoxicity grown on the 24-well ALI insert (LDH assay). UFP exposure resulted in decreased cell viability (significantly increased LDH levels). The result shows that Acrylonitrile butadiene styrene (ABS) has the most significant particle emission. ALI exposures enable in vitro testing of mixtures of particles such as UFP from a 3D printer. ABS is the only filament with a significant difference compared with the HEPA control in 90 minutes of exposure (p-value &lt;0.05). ABS and PETG we used during the experiment presented a significant difference compared with the HEPA control in 45 minutes of exposure.A screening analysis of potential exposure to these products in a typical environment suggests caution should be used when operating many printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.

Multimodal user interfaces promise a natural and intuitive human machine interactions. But is the extra effort for the development of a complex multi-sensor system justified, or can users also be satisfied with one input modality already? This study investigates interactions in an industrial weld inspection workstation. Three unimodal interfaces, including spatial interaction with buttons augmented on a workpiece or a worktable, and speech commands, were tested individually and in a multimodal combination. Within the unimodal conditions, users preferred the augmented worktable, but overall, the interindividual usage of all input technologies in the multimodal condition was ranked best. Our findings indicate that the implementation and use of multiple input modalities is valuable, and that it is difficult to predict the usability of individual input modalities for complex systems.

Superantigens are unconventional antigens which recognise immune receptors outside the usual binding sites e.g. complementary determining regions (CDRs), to elicit a response within the target cell. T-cell superantigens crosslink T-cell receptors and MHC Class II molecules on antigen-presenting cells, leading to lymphocyte recruitment, induction of cytokine storms and T-cell anergy or apoptosis among many other effects. B-cell superantigens, on the other hand, bind immunoglobulin receptors on B-cells affecting opsonisation, IgG-mediated phagocytosis, and drive B-cells into apoptosis. Here, through a review of the structural basis for recognition of immune receptors by superantigens, we show that their binding interfaces share specific physicochemical characteristics when compared with other protein-protein interaction complexes. Given that antibody-binding superantigens have been exploited extensively in industrial antibody purification, these observations could facilitate further protein engineering to optimize the use of superantigens in this and other areas of biotechnology.

The electrical stimulation of the visual cortices has the potential to restore vision to blind individuals. Until now, the results of visual cortical prosthetics has been limited as no prosthesis has restored a full working vision but the field has shown a renewed interest these last years thanks to wireless and technological advances. However, several scientific and technical challenges are still open in order to achieve the therapeutic benefit expected by these new devices. One of the main challenges is the electrical stimulation of the brain itself. In this review, we analyze the results in electrode-based visual cortical prosthetics from the electrical point of view. We first briefly describe what is known about the electrode-tissue interface and safety of electrical stimulation. Then we focus on the psychophysics of prosthetic vision and the state-of-the-art on the interplay between the electrical stimulation of the visual cortex and phosphene perception. Lastly, we discuss the challenges and perspectives of visual cortex electrical stimulation and electrode array design to develop the new generation implantable cortical visual prostheses.

Molecular causal interactions are defined as regulatory connections between biological components. They are commonly retrieved from biological experiments, and can be used for connecting biological molecules into regulatory computational models that represent biological systems. However, including a molecular causal interaction into a model requires assessing its relevance to that model, based on detailed knowledge about the biomolecules, interaction type, and biological context. In order to standardize the representation of this knowledge in ‘causal statements’, we recently developed the MI2CAST guidelines. Here we introduce causalBuilder: an intuitive web-based curation interface for the annotation of molecular causal interactions that comply with the MI2CAST standard. The causalBuilder prototype essentially embeds the MI2CAST curation guidelines in its interface, and makes its rules easy to follow by a curator. In addition, causalBuilder serves as an original application of the VSM general-purpose curation technology, and provides both curators and tool developers with an interface that can be fully configured to allow focusing on selected MI2CAST concepts to annotate. After information is entered, the causalBuilder prototype produces genuine causal statements that can be exported in different formats.

As education becomes more and more important in creating improved societies, many people who do not have access to it are falling behind. To help them catch up, many people, especially those in rural areas and developing countries, are turning to different methods of self-learning, especially those that utilize cheap technology and use interactive methods to teach. Our empirical study tests the effectiveness of an e-learning system that utilizes newer, less tested forms of interactivity and could potentially be used in these areas as a self-learning system and compares it to non-interactive video and textbook self-learning in two different topics. The results of the experiment showed that the increased interactivity provided by the e-learning system achieved significantly better learning performance over both non-interactive video and textbook self-learning. It was also found that students who learned through non-interactive video performed significantly better than those who used textbooks for self-learning.

Three-phase interactions (metal-slag-argon) in ladle stirring operations have strong effects on metal-slag mass transfer processes. Specifically, the thickness of the slag controls the fluid turbulence to an extent that once trespassing a critical thickness, increases of stirring strength have not further effects on the flow. To analyze these conditions, a physical model considering the three phases was built to study liquid turbulence in the proximities of the metal-slag interface. A velocity probe placed close to the interface permitted the continuous monitoring and statistical analyses of turbulence. The slag-eye opening was found to be strongly dependent on the stirring conditions, and the mixing times decreased with thin slag thicknesses. Slag entrainment was enhanced with thick slag layers, and high flow rates of the gas phase. A multiphase model was developed to simulate these results finding a good agreement between experimental and numerical results.

Joining of aluminium alloys to steels has been extensively studied, especially in the automotive sector. However, aluminium alloys are known to be difficult to join with steels when methods involving fusion welding are used because of hot cracking problem. Hence, a high strength joint between these dissimilar metals would be of benefit especially in reducing the weight of products. In this work the torch brazing method was applied to join AR500 steel with AA7075 aluminium alloy using Al-Si-Zn base filler metal at various flame times. The effect of the brazing work on the intermetallic phase formation and the mechanical strength of the joints were investigated. In this work, the maximum shear load obtained was 6460 N and the presence of the intermetallic phases had reduced the shear strength of the brazed joints. However, the torch brazing process using Al-Si-Zn filler metal had successfully facilitated the joining of these dissimilar metals.

In order to understand the hot deformation behavior of novel Cu/Al laminated composites, isothermal hot compression tests were conducted by Gleeble-1500D thermo-mechanical simulator. And the effect of bonding interface, deformation temperature and strain rate on the deformation behavior was analyzed. Results show that under the interface constraint effect, soft Al layer trends to flow synchronously with hard Cu layer. And further microstructure examinations indicate the cooperative deformation capability of Cu/Al composites increases with increasing stain rate and decreasing deformation temperature. Strain hardening exponent, calculated based on the true stress-true strain data, also proves the effect of deformation temperature and strain rate on the cooperative deformation behavior. Meanwhile, unique composites structure allows the Al matrix to exhibit the characteristic of dynamic recrystallization during the hot deformation process. Lastly, strain compensated Arrhenius-type constitutive equation was employed to describe the coupling effect of temperature, strain rate and strain on the flow stress.

In this paper, a novel integrated high precision vacuum microelectronic accelerometer is put forward based on the theory of field emission, the accelerometer consists of sensitive structure and interface ASIC. The sensitive structure has a mass of a cathode cone tips array, a folded beam, an emitter electrode and a feedback electrode. The sensor is fabricated on a double side polished (1 0 0) N-type silicon wafer, the tips array of cathode are shaped by wet etching with HNA (HNO3, HF and CH3COOH) and metalized by TiW/Au thin film. The structure of sensor is released by ICP process finally. The interface ASIC was designed and fabricated based on the P-JFET high voltage bipolar process. The accelerometer is tested through static field rollover test, and the test results show the integrated vacuum microelectronic accelerometer has good performances, which sensitivity is 3.081V/g and non-linearity is 0.84% in the measuring range of −1g~1g.

Although there is a common physiological notion that the origin of the membrane potential is attributed to transmembrane ion transport, it is theoretically possible to explain its generation by the mechanism of ion adsorption. It was previously suggested that the ion adsorption mechanism led even to the potential formulas which are even identical to either the famous Nernst equation or Goldman-Hodgkin-Katz equation. Our further analysis shown in this paper indicates that the potential formula based on the ion adsorption mechanism leads to one equation which is the function of material surface charge density and the material surface potential. Furthermore, we confirmed that the equation holds in all the different experimental systems we studied. Although we have not succeeded in elucidating why such an equation is established, the equation appears to be the key equation governing the characteristics of the membrane potential regardless of the systems in question.

An all-weather land surface temperature (LST) product derived at the Satellite Application Facility on Land Surface Analysis (LSA-SAF) is presented. The product is based on clear-sky LST retrieved from MSG/SEVIRI infrared (IR) measurements, complemented by LST estimated with a land surface energy balance (EB) model to fill gaps caused by clouds. The EB model solves the surface energy balance mostly using products derived at LSA-SAF. The new product is compared with in situ observations made at 3 dedicated validation stations, and with a Microwave (MW) based LST product derived from AMSR-E measurements. The validation against in-situ LST indicates an accuracy of the new product between -0.8 K and 1.1 K and a precision between 1.0 K and 1.4 K, generally showing a better performance than the MW product. The EB model shows some limitations concerning the representation of the LST diurnal cycle. Comparisons with MW LST generally show higher LST of the new product over desert areas, and lower LST over tropical regions. Several other imagers provide suitable measurements for implementing the proposed methodology, which offers the potential to obtain a global, nearly gap-free LST product.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Epilepsy is a chronic neurological disorder characterized by recurring seizures resulting from abnormal neuronal hyperexcitability. In the case of pharmacoresistant epilepsy requiring resection surgery, identifying the epileptogenic zone (EZ) is crucial. Fast ripples (FRs; 200-600 Hz) are one of the promising biomarkers that can aid in EZ delineation. However, recording FRs requires small surface electrodes. These microelectrodes suffer from high impedance, which significantly impacts FR observability and detection. In this study, we explored the potential of a conductive polymer coating to enhance FR observability. We employed biophysical modeling to compare two types of microelectrodes: Gold (Au) and Au coated with the conductive polymer poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (Au/PEDOT:PSS). These electrodes were then implanted in the CA1 hippocampal neural network of epileptic mice to record FRs during epileptogenesis. Results showed that polymer-coated electrodes demonstrate two-order lower impedance and a higher transfer function amplitude and cut-off frequency. Consequently, FRs recorded with the PEDOT:PSS coated microelectrode yielded significantly higher signal energy compared to the uncoated one. The coating with PEDOT:PSS improved the observability of recorded FRs and therefore their detection. This work paves the way for the development of signal-specific microelectrodes design allowing better targeting of pathological biomarkers.

Advances in biomimetic triboelectric nanogenerators (TENGs) have significant implications for electronic skin (e-skin) and human-machine interaction (HMI). Emphasizing the need to mimic complex functionalities of natural systems, particularly human skin, TENGs leverage triboelectricity and electrostatic induction to bridge the gap in traditional electronic devices' responsiveness and adaptability. The exploration begins with an overview of TENGs' operational principles and modes, transitioning into structural and material biomimicry inspired by plant and animal models, proteins, fibers, and hydrogels. Key applications in tactile sensing, motion sensing, and intelligent control within e-skins and HMI systems are highlighted, showcasing TENGs' potential in revolutionizing wearable technologies and robotic systems. This review also addresses the challenges in performance enhancement, scalability, and system integration of TENGs. It points to future research directions, including optimizing energy conversion efficiency, discovering new materials, and employing micro-nanostructuring techniques for enhanced triboelectric charges and energy conversion. The scalability and cost-effectiveness of TENG production, pivotal for mainstream application, are discussed along with the need for versatile integration with various electronic systems. The review underlines the significance of making bioinspired TENGs more accessible and applicable in everyday technology, focusing on compatibility, user comfort, and durability. Conclusively, it underscores the role of bioinspired TENGs in advancing wearable technology and interactive systems, indicating a bright future for these innovations in practical applications.

In the last decades, the automatic recognition and interpretation of brain waves acquired by electroencephalographic (EEG) technologies have undergone remarkable growth, leading to a consequent rapid development of Brain Computer Interfaces (BCIs). EEG-based BCIs are non-invasive systems that allow communication between a human being and an external device interpreting brain activity directly. Thanks to the advances in neurotechnologies, and especially in the field of wearable devices, BCIs are now also employed outside medical and clinical applications. Within this context, this paper proposes a systematic review of EEG-based BCIs, focusing on one of the most promising paradigms based on Motor Imagery (MI) and limiting the analysis to applications that adopt wearable devices. This review aims to evaluate the maturity levels of these systems, both from the technological and computational points of view. The selection of papers has been performed following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA), leading to 84 publications considered in the last ten years (from 2012 to 2022). Besides technological and computational aspects, this review also aims at systematically list experimental paradigms and available datasets in order to identify benchmarks and guidelines for the development of new applications and computational models.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

Abstract The construction of a heterostructured nanowire array allows the manipulation of the interfacial, surface, charge transport, and transfer properties simultaneously, offering new opportunities to achieve multi-functionality for various applications. Herein, we developed a facile thermal evaporation and post-annealing method to synthesize ternary-Zn2SnO4/binary-ZnO radially heterostructured nanowire arrays (HNA). Vertically aligned ZnO nanowire arrays (3.5 μm in length) were grown on a ZnO-nanoparticle-seeded fluorine-doped tin oxide substrate by a hydrothermal method. Subsequently, the amorphous layer consisting of Zn-Sn-O complex was uniformly deposited on the surface of the ZnO nanowires via the thermal evaporation of the Zn and Sn powder mixture in vacuum, followed by post-annealing at 550 °C in air to oxidize and crystallize the Zn2SnO4 shell layer. The use of a powder mixture composed of elemental Zn and Sn (rather than oxides and carbon mixture) as an evaporation source ensures high vapor pressure at a low temperature (e.g., 700 °C) during thermal evaporation. The morphology, microstructure, and charge-transport properties of the Zn2SnO4/ZnO HNA were investigated by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, transmission electron microscopy, and electrochemical impedance spectroscopy. Notably, the optimally synthesized Zn2SnO4/ZnO HNA shows an intimate interface, high surface roughness, and superior charge-separation and -transport properties compared with the pristine ZnO nanowire array.

Scientific progress is increasingly dependent on knowledge in computation-ready forms. In the life sciences, among others, many scientists therefore extract and structure knowledge from the literature. In a process called manual curation, they enter knowledge into spreadsheets, or into databases where it serves their and many others' research. Valuable as these curation efforts are, the range and detail of what can practically be captured and shared remains limited, because of the constraints of current curation tools. Many important contextual aspects of observations described in literature simply do not fit in the form defined by these tools, and thus cannot be captured. Here we present the design of an easy-to-use, general-purpose method and interface, that enables the precise semantic capture of virtually unlimited types of information and details, using only a minimal set of building blocks. Scientists from any discipline can use this to convert any complex knowledge into a form that is easily readable and meaningful for both humans and computers. The method VSM forms a universal and high-level language for encoding ideas, and for interacting with digital knowledge.

VSM is a recently introduced method for entering and displaying any type of knowledge, in a form that is both semantically precise for computation and intuitive for human understanding. VSM is the combination of a new semantic model, and the design for a dedicated user interface to support it. Here we present the implementation of this user interface, as a sophisticated HTML-element, <vsm-box>, that can be embedded in any web-based curation app. We show how developers can use it for biocuration projects, customize it to particular end-user needs, and contribute to its growth. Vsm-box is open-source at https://github.com/vsmjs/vsm-box under the AGPL license, as a JavaScript (ES6) Vue.js web-component that runs in all modern web browsers. It is the capstone of the Vsmjs organization at https://github.com/vsmjs that groups its supporting modules. Extensive supplementary material on VSM and vsm-box is available at https://vsmjs.github.io.