Particle size can pose a challenge to random embankment compaction control methods, where practical techniques have hardly been developed and procedural control is used instead. In order to develop new quality control procedures for slate random fill, the necessary fieldwork and laboratory tests were carried out. This involved the revision of certain methods such as the wheel-tracking or topographic settlement tests. More than six hundred in-situ density and moisture content measurements were carried out for this research. In addition, more three hundred topographic settlements and three hundred wheel-tracking carriage tests were performed. The quality control processes were completed with more than thirty plate bearing tests. Possible evidence of statistical correlations between compaction control tests were identified. An analysis of variance (ANOVA) was performed. When testing proved relationships between them, the replacement of one of them by the other was assessed by deduction. Finally, the study suggests new procedures for compaction quality control of random slate fill used in crown area.

The calculation of the release of liquid hazardous chemicals storage tanks is an important part of the quantitative risk assessment of accidents. This paper mainly establishes a continuous real–time release model based on the instantaneous mass flow Q_m model. Meanwhile, the software function module was analyzed, and programming software was developed using C# language for model solving. A series of experiments for repeated leakage tests was designed and the discharges through three small holes with different heights for 200 s were observed. The results show that the continuous real–time leakage model is effective, and the deviation between theoretical and experimental release amounts are within a reasonable range. The higher the liquid level above the leak hole is, and the smaller the height of the leak hole from the ground is, the greater the flow rate at the leak orifice is and the smaller discharge rate change is. Therefore, the deviation between the theoretical release amount M_t and the experimental average release amount Ma is greater while the height of the leak hole from the ground is smaller, which indicates that the smaller the distance from the leak orifice to the ground, the greater the influence of the empirical discharge coefficient C₀ on the release amount M.

Since the 1970s, land subsidence has been developing rapidly in the Beijing Plain, the systematic study of its evolution mechanism is of great significance to the sustainable development of the regional economy. First, based on ENVISAT ASAT and RADARSAT2 data, the land subsidence data in Beijing Plain were obtained using permanent interferometer technology. Second, based on the GIS platform and using fishing net tools, vector data of ground settlement with different resolutions were obtained. Through a series of tests, a scale of 960 metres was selected as the research unit, and the subsidence rate of the grid was obtained from 2004 to 2015. Finally, based on the Mann-Kendall mutation test method, a trend analysis of land subsidence changes in various grids was carried out. The results showed that single-year mutation mainly distributed in the middle and lower parts of the Yongding River alluvial fan and the Chaobai River alluvial fan, mainly occurring in 2015, 2005 and 2013, respectively. The upper and middle alluvial fan of the Chaobai River, the vicinity of the emergency water source and the edge velocity of the groundwater funnel have undergone several sudden changes. Combined with hydrogeology, basic geological conditions and the impact of the South-to-North Water transfer project, we analysed the causes of the mutations in the grid. The research results can provide a basis for the study and prevention of land subsidence in this area and help to further explore the trend characteristics of land subsidence in this area.

The determination of the non-loading condition of the rail cable shifting (RCS) system, which consists of main cables, hangers and rail cables, is the premise of the girder erection for the long-span suspension bridges. An analytical form-finding analysis model of shifting system is established according to the basic assumptions of flexible cable structures. Herein, the rail cable is discretized into segmental linear cable elements and the main cable is discretized into segmental catenary elements. Moreover, the calculation and analysis equation of each member and their iterative solutions are derived by taking the elastic elongation of the sling into account. In addition, by taking the girder construction of Aizhai suspension bridge as engineering background, a global scale model of the RCS system is designed and manufactured; also the test system and working conditions are established. The comparison between the test results and analytical results shows the presented analytical method is correct and effective. The process is simplified in the analytical method, and the computational results and precision can satisfy the practical engineering requirements. In addition, the proposed method is suitable to apply to the computation analysis of similar structures.

2.25Cr-1Mo steel with high strength at high temperatures and good hydrogen resistance is widely used for power generation boiler material in high temperature and pressure use environments. Following the test evaluation of the ASME Boiler and Pressure Vessel Code, specimens from the base metal of a boiler pipe were found to have impact toughness values of 285 and 21 ft-lb, which are drastically different values. The analysis of the fracture surface of the 21 ft-lb test specimen revealed MnS inclusions, and it was found that cracks initiated at the inclusions. Observation of the cross-section of the crack propagation front revealed that cracks propagated along the ferrite regions and precipitate voids. Inclusions were also found in the 285 ft-lb impact specimen; however, the volume fraction of the inclusions was significantly less than that of the 21 ft-lb specimen. It was also found that the ferrite and carbide content of the 285 ft-lb specimen was less than 21 ft-lb specimen. The reason that the inclusions, ferrite, and carbide content differed in the two adjacent impact test specimens was analyzed. The effects of micro-segregation, such as MnS inclusions on ferrite and carbide, were compared and analyzed.

Impact characterization of linear resonant actuator (LRA) is studied experimentally by newly developed drop tester, which can control various experimental uncertainty such as rotational moment, air resistance, secondary impact and so on. The feasibility of this test apparatus was verified by comparison with free fall test. By utilizing a high-speed camera and measuring the vibrational displacement of spring material, the impact behavior was captured and the damping ratio of the system was defined. Based on the above processes, the finite element model was established and the experimental and analytical results were successfully correlated. Finally, the damage of the system from impact loading can be expected by developed model and as a result, this research can improve the impact reliability of LRA.

The lack of accurate and feasible diagnostic tests poses a significant challenge to visceral leish-maniasis (VL) healthcare services in endemic areas. To date, various VL diagnostic tests have been or are being developed, and their diagnostic performance needs to be assessed.. In the present study, the diagnostic performance of rk39RDT, Direct Agglutination Test (DAT), Microscopy, Loop Mediated Isothermal Amplification (LAMP), and miniature direct-on-blood polymerase chain reaction - nucleic acid lateral flow immunoassay (mini-dbPCR-NALFIA) was assessed using quantitative polymerase chain reaction (qPCR) as reference test in an endemic region of Ethiopia. In this study, 235 patients VL suspected patients and 104 non-endemic healthy controls (NEHC) were recruited. Among the VL-suspected patients, 144(61.28%) tested positive with qPCR. Sensi-tivities for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA were 88.11%, 96.50%, 76.58%, 94.33%, and 95.80%, respectively. Specificities were 83.33%, 97.96%, 100%, 97.38%, and 98.92% for rk39 RDT, DAT, Microscopy, LAMP assay, and mini-dbPCR-NALFIA, respectively. In conclusion, Rk39 RDT and microscopy exhibited lower sensitivity, while DAT demonstrated excellent performance. LAMP and mini-dbPCR-NALFIA showed excellent perfor-mance with feasibility to implement in remote endemic areas, although the latter requires further evaluation in such regions.

As a new plant slope protection technology, living stumps can effectively improve slope stability. The current study attemptes to investigate the mechanical characteristics of the root system of living stumps and their reinforcement mechanism on slopes by carrying out a three-dimensional living stump slope modeling test. Using ABS materials, a 3D model of a living elm stump was created by 3D printing and a slope model test was carried out. The reinforcement mechanism of the living stump was studied through a combination of model testing and numerical simulation. The results indicate that, due to the presence of living stumps in the lower and middle parts of the slope, the maximum shear stress area of the soil moved to a deeper direction. The stress state of the soil around the living stump was effectively improved due to the existence of the lateral root system.Living stumps in the lower part of the slope cross the potential sliding surface and transferred the soil shear stress gradually to the root system through root-soil interaction. Moreover, the tap roots and lateral roots of living stumps form a robust spatial structure that bears the shear stress of soil together, thus increasing the stability of the slope.

The liver diseases are posing serious threat to human health associated with abusive use of allopathy medicines, especially in developing economies like Pakistan. The strengthening of detoxification system using natural products might be a suitable option to minimize the liver problems. In this current research, Zingiber officinale and Azadirachta indica were evaluated for their hepatoprotective role. For the purpose, 20 Sprague Dawley rats were equally divided into four groups i.e., negative control, paracetamol positive control, 2.5% ginger and 2% neem powder, respectively. During 42 days study, the levels of bilirubin and liver enzymes significantly elevated due to liver damage. Although, the values dropped (20-25%) in treatment group. Serum glucose and serum lipid profile increased in positive control group, but reduced (5-10%) in both ginger and neem groups. The serum protein profile declined in liver damage group, however, improved (~5%) in treatment groups. The hematological parameters slightly declined in liver damage group, but increased in ginger and neem groups. Moreover, the white blood cells differential count and renal parameters showed abnormal values in liver damage group, but improved after treatment. This study is promising and highlighted the hepato-protective role of neem and ginger that may open several avenues of research.

This retrospective study examines 248 test-bolus examinations preceding contrast-enhanced magnetic resonance angiography (CE-MRA) to extract clinically relevant data for critical limb ischemia (CLI) management. Methods involved a retrospective review of test-bolus exams, analysing 60 graphs for time-to-peak (TTP), full-width half-maximum (FWHM) time, and time to continual rise in signal intensity. These values were correlated with heart function parameters (ejection fraction, ASA-Classification, Lee-Index, and MET-Score). Results indicate a mean TTP of 31.2 ± 7.3s, showing a correlation between ejection fraction and ASA classification. Patients with atrial fibrillation exhibited prolonged TTP compared to those without. Despite population heterogeneity, findings facilitate risk stratification for limb-saving interventions in CLI. TTP emerges as a potential clinical cardiovascular parameter and a risk factor for vascular interventions. Given the variation in injection protocols across centres, this study underscores the importance of precise bolus arrival time documentation for future multicentre studies.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

Microvascular self-healing composite materials have significant potential for application and their mechanical properties need in-depth investigation. In this paper, tensile and compressive properties of woven fabric carbon fiber reinforced polymers (CFRP) laminates containing three-dimensional microvascular channels were investigated experimentally. Several detailed finite element (FE) models were established to simulate the mechanical behavior of the laminate and the effectiveness of different models were examined. The damage propagation process of the microvascular laminates and the influence of microvascular parameters were studied by the validated models. The results show that microvascular channels arranged along the thickness direction (z-direction) of the laminates are critical locations under the loads. The channels have minimal effect on the stiffness of the laminates but causing a certain reduction in strength, which varies approximately linearly with the z-direction channel diameter within its common design range of 0.1~1mm. It is necessary to consider the resin-rich region formed around microvascular channels in the warp and weft fiber yarns of the woven fabric composite when establishing the FE model. And the layers in model should be assigned with equivalent unidirectional ply material in order to calculate the mechanical properties of laminates correctly.

To analyze the viral titers of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) and respiratory syncytial virus (RSV) at the anterior nasal site (ANS) and nasopharyngeal site (NS), evaluate their virological dynamics, and validate the usefulness of a newly developed two antigen-detecting rapid antigen diagnostic test (Ag-RDT) that simultaneously detects SARS-CoV-2 and RSV using clinical specimens. This study included 195 asymptomatic to severely ill patients. Overall, 668 specimens were collected simultaneously from the ANS and NS. The cycle threshold (Ct) values calculated from real-time polymerase chain reaction were used to analyze temporal changes in viral load and evaluate the sensitivity and specificity of the Ag-RDT. The mean Ct values for SARS-CoV-2-positive, ANS, and NS specimens were 28.8, 28.9, and 28.7, respectively. The mean Ct values for RSV-positive, ANS, and NS specimens were 28.7, 28.8, and 28.6, respectively. SARS-CoV-2 and RSV showed the same trend in viral load, although the viral load of NS was higher than that of ANS. The sensitivity and specificity of the newly developed Ag-RDT were excellent in specimens collected up to 10 days after the onset of SARS-CoV-2 infection and up to 6 days after the onset of RSV infection.

When designing the battery of an electric vehicle, different parameters must be considered to obtain the safest arrangement of the battery/modules/cells from the mechanical and thermal point of view. In this study, the thermal runaway propagation mechanism of lithium-ion cells is analyzed as a function of their arrangement within a battery pack in case of a fire propagation of a battery pack in which a thermal runaway has occurred. The objective is to identify which cell/module arrangement is most critical within the battery pack by microscopic analysis of the structure and chemical composition of the most damaged cells, both horizontally and vertically, of a battery belonging to a burnt vehicle. And their final condition has been compared with the condition of new cells of the same type. In this way the structure and chemical composition of the anode, cathode and separator after Thermal Runaway has been compared. This research has been carried out to obtain information to understand the mechanical properties of lithium-ion cells and their behavior after thermal runaway heating leading to the propagation of a fire. Through the analysis carried out, it is concluded that cells placed in a vertical arrangement have worse behavior than cells in a horizontal arrangement. Regarding the safety of the battery, the results of this study will allow to determine which arrangement and structure of the cells within the battery pack is safer against thermal runaway due to thermal failure.

Digital Image Correlation (DIC) is an optical technique used to measure surface displacements and strains in materials and structures. This technique has demonstrated significant utility in structural examination and monitoring. This manuscript offers a comprehensive review of contemporary research and applications that have leveraged the DIC technique in laboratory-based structural tests. The reviewed works encompass a broad spectrum of structural components, such as concrete beams, columns, pillars, masonry walls, infills, composite materials, structural joints, steel beams, slabs, and other structural elements. These investigations have underscored the efficacy of DIC as a metrological instrument for precise quantification of surface deformation and strain in these structural components. Moreover, the constraints of the DIC technique have been highlighted, especially in scenarios involving extensive or complex test configurations. Notwithstanding these constraints, the DIC methodology has validated its effectiveness as a strain measurement instrument, offering numerous benefits such as non-invasive operation, full-field measurement capability, high precision, real-time surveillance, and compatibility with integration into other measurement instruments and methodologies.

I demonstrate that Bell's theorem is based on circular reasoning and thus a fundamentally flawed argument. It unjustifiably assumes the additivity of expectation values for dispersion-free states of contextual hidden variable theories for non-commuting observables involved in Bell-test experiments, which is tautologous to assuming the bounds of ±2 on the Bell-CHSH sum of expectation values. Its premises thus assume in a different guise the bounds of ±2 it sets out to prove. Once this oversight is ameliorated from Bell's argument, the bounds on the Bell-CHSH sum of expectation values work out to be ±2√2 instead of ±2, thereby mitigating the conclusion of Bell's theorem. Consequently, what is ruled out by the Bell-test experiments is not local realism but the additivity of expectation values, which does not hold for non-commuting observables in any hidden variable theories to begin with.

In this paper we study a special kind of finite mixture model. The sample drawn from the model consisits of three parts. The first two parts are drawn from specified distributions f1 and f2, while the third one is drawn from the mixture. A problem of interest is whether the two distributions f1 and f2 are the same. To test this hypothesis, we first define the regular location and scale family of distributions and assume that f1 and f2 are regular denisty functions. Then the hypothesis transforms to the equalities of the location and scale parameters, respectively. To utilize the information in the sample, we use Bayes’ theorem to obtain the posterior distribution and give the sampling method. Then we propose the posterior p-value to test the hypothesis. The simulation studies show that our posterior p-value largely improves the power in both normal and logistic cases while nicely controls the Type-I error. A real halibut dataset is used to illustrate the validity of our method.

In this study, based on frost formation data provided by Harbin Meteorological Bureau, combined with geographical factors, temperature and population density, linear fitting, Mann-Kendall mutation test, pettitt method and sliding T test were used to analyze the spatio-temporal variation characteristics of frost date in Harbin Municipality and the effects of geographical factors, temperature and population density on frost regularity. The results showed that (1) The earliest year of FSD appeared was 1966 and 1967, on the 255th, i.e., August 18th, and the latest was 283 days, i.e., October 10th, 2006. The earliest year in which the FED appeared was April 24th of 2015, the 114th day of that year, and the latest was April 21st of 1974, the 141st day of that year. The year with the most frost was 2012, with 161 days, and the year with the shortest was 1966, with 123 days. (2) Throughout the study period, FSD increased by 7.8 days at a rate of -1.27d/10a, FED increased by 10.9 days at a rate of 1.77d/10a, and FFS increased by 18.9 days at a rate of 3.05d/10a. The tendency rate of FSD and FFS at each site in Harbin showed an increasing trend. For FED, the tendency rate of some sites showed an increasing trend. In general, FSD showed a delayed trend, FED showed an advanced trend, and FFS showed a prolonged trend. Using the method of unary linear regression, FSD of each site showed an increasing trend, FFS showed an increasing trend, and FED showed a decreasing trend in general. (3) Throughout the study period, FSD was mutated in 2000, and the arrival time of it in the study area averaged the 265th, i.e., September 22nd, and after that, the arrival time of it changed to the 272nd, i.e., September 29th of that year. FED was mutated in 2006, and the arrival time of it in the study area averaged 128th, i.e., April 8th. After the mutation, the arrival time of FED changed to 121st, i.e., April 1st of that year. FFS was mutated in 2004. Before the mutation, with an average arrival time of 137days in the study area .But after that, the time changed to 150 days.(4) FSD and FFS in Harbin Municipality were negatively correlated with latitude and positively correlated with temperature, while FED was positively correlated with latitude and negatively correlated with temperature. The FSD, FED and FFS in the central part of Harbin Municipality were the earliest, the latest and the longest, respectively, so the Pearson correlation coefficient method and the influence of longitude could not be reflected in the multiple regression. Several factors were judged by grey correlation analysis method. The longitude is significantly related to FSD, FED and FFS.

An empirical investigation was carried out to study the relationship between the soil characteristics, including the Nitrogen (N), Phosphorus (P), Potassium (K), potential of Hydrogen (pH), Electrical conductivity (EC), Sulfur (S,), Zinc (Zn), Iron (Fe), Copper (Cu), Manganese (Mn) and Boron (B) using principal component analysis (PCA), Factor Analysis (FA), and Canonical Correlation analysis (CCA) for data reduction multivariate techniques. The first five main components accounted for 24.22%, 18.52%, 16.1%, 9.97%, and 9.27% of sample variances, respectively. All five principal components (PCs) accounted for 78.07% of the sample variance. The soil characteristics viz., P and K have highly dominated the first PC; the soil characteristics N and pH have dominated the second PC; K, EC, and Cu have dominated the third PC; Fe, Mn, and pH have dominated in the fourth PC; whereas the parameter Cu dominated the fifth PC. The first factor showed a strong negative loading on S and a strong favorable loading on Cu; P, K, and EC have substantial positive loadings in the second factor. Significant positive loadings on Mn, Fe, Cu, pH, N, and K are present in the third component. The fourth factor had a significantly positive pH, Fe, N, P, K, and B loadings. Fe, P, and B have much weight in the fifth factor. The soil characteristics viz., N, Zn, pH, K, Fe, and Mn have dominated the first PC; the soil characteristics B, P, S, Zn, and Fe have dominated the second PC; B and P have dominated the third PC whereas the only character Cu dominated the fourth PC. Cu and OC have much weight in the fourth factor. The canonical redundancies for dependent and independent sets are 12% and 17%, respectively. The Stewart-Love canonical redundancy index is 70.58%, which means that the first linear combination of the X-set explains 70.58% of the total variance in the Y-set.

Seepage erosion is one of the main reasons for the local collapse or instability of embankments. To investigate the characteristics and mechanism of seepage erosion for cohesionless soils, the model tests by using an independently developed seepage erosion device and the numerical simulations based on the Discrete Element Method-Computational Fluid Dynamics (DEM-CFD) coupling model were carried out. The results show that the seepage erosion process of the cohesionless soil can be characterized by four stages: stable seepage stage, fine particles upward migration stage, sand samples boiling stage, and erosion damage stage. The skeleton structure of soil sample under seepage flow is continually changed due to the loss of fine soil particles, which results in a significant decrease in the sample strength and may ultimately lead to the failure of the sample. The results of this study can provide references and bases for the design, construction, and long-term service of embankments or earth dams under the complex seepage condition, reducing the risk of seepage erosion.

For earthquakes (M4.0) occurring along and arond the East Anatolian fault zone and the the Dead Sea fault zone between January 2002 and December 2022, we analyzed the correlation between the Earth's rotation and the earthquake occurrence before the Mw7.8 Gaziantep,Turkey earthquake occurring on 6 February 2023. We statistically evaluate the Earth's rotationally dependent seismicity. The results were judged by the P-value. There was a clear downward trend in the P-values from early 2020 to late 2022 in the study region. Starting in early 2021, the P-value drops below 0.1%, corresponding significant correlation between the Earth's rotation and the earthquake occurrence . We also calculated the spatial distribution of the P-values and obtained a result showing a low P-value area in the vicinity of the northeastern end of the aftershock zone. Although the stress caused by the Earth's rotation is very weak, when the focal medium is loaded to the critical state to release a large earthquake, the stress due to the Earth's rotation could control the earthauqke occurrence. Therefore, the lower P-values obtained in this study indicates the Earth's rotation-related seismicity prior to the Mw 7.8 Turkey earthquake and could be considered as its precursor.

Background: Asthma is a very prevalent disease with special characteristics during pregnancy, however little is known about its relation to the psychological wellbeing of women in this period; We aimed to know whether depression and anxiety symptoms are more frequent in asthmatic pregnant women. (2) Methods: Family Apgar (week 20), Edinburgh (weeks 20 and 32) and STAI (week 32) tests were administered to 738 pregnant women (81 asthmatics) in the NELA birth cohort; (3) Results: There were no significant differences between asthmatic and non-asthmatic pregnant women in any of the different tests at any of the time points. The mean? scores for the different tests and timepoints between asthmatic and non-asthmatic pregnant women were: Apgar 20, 17.9±2.2 vs. 10.0±2.2; Edinburgh 20, 6.7±4.2 vs. 6.9±4.3; Edinburgh 32, 5.9±4.4 vs. 5.6±4.3; and STAI 32, 16.7±8.4 vs. 15.8±8.3. The proportion of pregnant women out of the normal range score for any of the tests and time points was also similar in both populations. (4) Conclusions: Asthma is not associated with the psychological wellbeing among pregnant women.

Neuropsychiatric disorders are globally public-health concern, in which diagnosis might be based on symptoms that often vary across individuals. Schizophrenia is one of the major neuropsychiatric disorders, which may affect millions worldwide. Detection of predictive biomarkers is the most intensively developing approach for the disease. However, the biochemical alterations have not been comprehensively distinguished up to the present time. In addition, there is less confidence of finding a specific biomarker for neuropsychiatric disorders including schizophrenia, but rather a specific characteristic behavioral pattern. Maternal immune activation has been considered to be one of the important factors for the development of neuropsychiatric disorders. Here, the mouse model of neuropsychiatric disorders has been built, in which poly-I:C, sodium dextran sulfate (DSS) and κ-carrageenan (CGN) were used for the maternal immune activation during the pregnancy of individuals. Subsequently, we challenged to link some of biochemical changes of p62 and GLAST in the offspring mice brain to the alteration of several pathological behaviors. Consequently, it has been shown that autophagy might be involved in the development of neuropsychiatric disorders including schizophrenia. To our knowledge, this is the first report of the significant correlation between pathological behavior and the biochemical alterations in neuropsychiatric disorder model animals. The relative ease of conducting these evaluation-tasks would make them useful for testing novel therapeutics designed to ameliorate the symptoms of several psychiatric disorders.

The main purpose of the work was to determine the powder composition and properties of iron-based sinters used as a matrix in metallic diamond tools. The FeCuSnNi sinters obtained from a mixture of commercial powders were used for research. The material was subjected to milling in a ball mill and sinter have been performed with the hot-pressing technique in a graphite mold. The physical and mechanical properties of the sinters were tested. The investigations of obtained sinters concerned density, porosity, hardness, oxygen content, static tensile test and analysis of microstructure. The static tensile test was carried out with the use of a universal testing machine UTS-100. The study of the microstructure of sinters was performed using the JSM-7100F scanning electron microscope. The sinters are characterized by a high coefficient of thermal expansion and good mechanical properties. The FeCuSnNi sinter revealed a complex phase structure. Spot chemical analysis revealed the presence of Fe solution, Cu solution and the presence of iron oxides oxides. Nickel atoms were present throughout the sinter volume. The obtained results indicate that the presented material can be used as a matrix of a diamond-metal composite in diamond tools for the processing of natural stones and building materials.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

Background: Arm elevation plays an important role in simple and complex daily tasks. Muscles that stabilize the shoulder girdle also function as respiratory accessory muscles. Dual demand on these muscles, particularly in patients with chronic respiratory conditions, leads to dyspnea and fatigue of the upper limb, making simple daily activities difficult. Various tests, including Grocery Shelving Task (GST), are designed to assess functional performance during upper limb activities. The aim of the study is to derive reference values for GST among the population of the United Arab Emirates Methods: This cross-sectional study was conducted with 220 healthy individuals of both genders between the ages of 20 and 69. Duration required to complete GST was recorded. The correlation between duration and age, height, body mass and body mass index (BMI) were also assessed. Results: Reference values for duration (in seconds) in females for age groups 20-29, 30-39, 40-49, 50-59 and 60-69 are 43.5±5.5, 43.1±8.08, 48.1±6.7, 44.9±7.1, 46.7±6.5 respectively. Values for males of age groups 20-29, 30-39, 40-49, 50-59 and 60-69 are 45.7±6.7, 44.8±8.9, 42.5±10.01, 53.4±4.2, and 53.9±5.4 respectively. Conclusion: Reference values for GST duration were obtained. Weak correlations were found between duration and age, height, body mass, BMI of the participants.

To assist Java programming learning of novice students, we have developed the web-based Java programming learning assistant system (JPLAS). JPLAS provides several types of exercise problems to cultivate code reading/writing skills at various levels. In JPLAS, the code writing problem (CWP) asks a student to write a source code that will pass the test code given in the assignment where the correctness is verified by running them on JUnit. In this paper, to reduce the teacher load at marking process, we present the answer code validation program that verifies all the source codes from a lot of students for each assignment at a time and reports the number of passing tests for each source code in the CSV file. Besides, to test a source code with various input data, we implement the test data generation algorithm that identifies the data type, generates a new data, and replaces it for each test data in the test code. Furthermore, to verify the correctness of the implemented procedure in the source code, we introduce the intermediate state testing in the test code. For evaluations, we applied the proposal to source codes and test codes in a Java programming course in Okayama university, Japan, and confirmed the validity and effectiveness.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

In this study, the focus is on the drop test simulation of an MR (Magnetorheological) damper-based main landing gear (MRMLG), aiming to explore multi-degree-of-freedom (DOF) dynamic models during aircraft landing. Three different 6-DOF dynamic models are proposed in this work and their drop performances are compared with results achieved one of commercial softwares. The proposed models include a nonlinear aircraft model (NLAM), a linearized approximated aircraft model (LAAM) linearizing from the nonlinear equations of motion in NLAM, and a fully approximated aircraft model (FAAM) which linearizes the MRMLG's strut force model. In order to evaluate drop performance of the aircraft landing gear system with MR dampers, a 7-DOF aircraft model incorporating the nonlinear MRMLG is formulated using RecurDyn. The principal comparative param-eters are the coefficient of determination (R2) for system response of each model with Re-curDyn model and root mean square error (RMSE) which is the ensembles of CG dis-placement data for each model. In addition, the ensemble of time series data is created for diverse drop scenarios, providing valuable insights into the performance of the proposed drop test models of the aircraft landing gear system featuring MR dampers.

To study the anti-cracking performance of cast-in-place concrete inner shaft lining structure under the combined effects of temperature and constraint, this paper first developed a novel temperature stress test machine suitable for the shape of the inner shaft lining structure and with adjustable endpoint constraint, providing specialized experimental equipment for subsequent cast-in-place concrete inner shaft lining temperature stress simulation experiments. Then, this paper preliminarily studied the temperature, strain, and stress changes of the cast-in-place inner shaft lining under the condition of 100% endpoint constraint by simulating the internal hydration heating and cooling process of the cast-in-place inner shaft lining and using the temperature stress test machine to accurately control the endpoint constraint conditions of the inner shaft lining scaled model.

In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..

Autonomic dysfunction is an increasingly recognised complication in chronic neurological conditions such as Parkinson’s disease , and other medical conditions, including diabetes mellitus, chronic fatigue syndrome, postural tachycardia syndrome with and without Ehlers-Danlos syndrome, fibromyalgia and recently Long Covid. Despite laboratory-based tests to evaluate normal and abnormal autonomic function, there are no home-based tests to record neuro-cardiovascular autonomic responses to common stimuli in daily life that are dependent on the normal functioning of the autonomic nervous system. We have developed an adapted blood pressure/heart Autonomic Profile (aAP) that can be used by an individual independently and repeatedly in a domiciliary setting to determine the physiological and symptomatic response to standing, food, and physical and mental (cognitive, emotional) activities. The aAP aids separating autonomic failure (often irreversible) from autonomic dysfunction. This helps the individual and attending healthcare professional understand the relationship between symptoms and common triggers in daily life and informs on self-management in debilitating conditions such as the postural tachycardia syndrome (PoTS) and Long Covid.

The experiments described in this research article were designed to test the effect of rare variants into genomic prediction in dairy cattle. Common polymorphisms are able to explain only a small proportion of the underlying genetic variation of complex phenotypes. Variants representing functional mutations with large effects on complex phenotypes are expected to be rare due to natural (humans) or artificial (livestock) selection pressure. Therefore, it is important to check whether the use of rare variants could increase the accuracy of ranking of animals by providing the tool for more precise differentiation among the bulls with high additive genetic merit. The goal of our study was to verify whether including rare variants in a genomic selection model allows for a more accurate description of the additive genetic background of traits under selection in dairy cattle. We used the linear mixed model for comparison SNP estimates for Holstein-Friesian cattle of the two data sets – a set containing only single nucleotide polymorphisms defined by minor allele frequency ≥ 0.01, which is routinely used in the Polish genomic evaluation system (46,216 SNPs), and a set containing SNPs selected based only on the call rate (54,378 SNPs). Based on the SNP estimates we also calculated DGV and GEBV and compared them between both data sets. In all the analyses we used production, fertility, conformation and udder health traits. We also assessed the time required for the two most computationally demanding components of genomic selection: preparing genotype data, and estimation of SNP effects between those two data sets. The results of our study indicated that the analysis including rare variants resulted in changes in the individual ranking of the top 100 male and female candidates, but had no effect on the outcome of the quality of EBV prediction as expressed by the Interbull validation test.

Hazelnut is a widespread nut species, especially in Europe, that can be consumed raw or roasted, due to its pleasant taste and nutritional properties. Despite the renowned beneficial properties, hazelnuts contain several proteins capable of inducing food allergy in sensitized individuals such as Cor a 2 (profilin), Cor a 8 (lipid transfer protein), Cor a 9 (11S seed storage globulin, legumin-like) and Cor a 11 (7S seed storage globulin, vicilin-like). In the present paper we investigated the effectiveness of autoclave based treatments in decreasing the allergic potential of hazelnut as also assessed by submitting the treated material to in vivo skin prick test and to in vitro immunoblot analysis with sera of allergic individuals exposed to the treated food material. This preliminary analysis shows that autoclave treatment, preceded by hydration and/or followed by drying, seems to be a promising approach and appears to be effective in reducing the allergenicity of hazelnut in most patients, probably due to the denaturation of most major and minor allergenic proteins. This work will open to the opportunity to produce, in perspective, hypoallergenic hazelnut derivatives tolerated by the allergic subjects.

COVID-19 pandemic will continue to pose a major public health threat until vaccination-mediated herd immunity is achieved. Most projections predict vaccine will reach a large subset of the population late in 2021 or early 2022. In the meantime, countries are exploring options to remove strict lockdown measures and allow for society and the economy to return to normal function. One possibility is to expand on existing COVID-19 testing strategies by including large-scale rapid point of care diagnostic tests (POCTs). Currently, there is significant variability in performance and features of available POCTs, making selection and procurement of appropriate test for specific use case difficult. In this review, we have used the World Health Organization’s (WHO) recently published Target Product Profiles (TPPs) for specific use cases of COVID-19 diagnostic tests to screen for top-performing POCTs on the market. Several top-performing POCTs, based on clinical sensitivity/specificity, the limit of detection, and time to results, that meet WHO TPP criteria for direct detection of SARS-CoV-2 (acute infection), or indirect diagnosis of past infection (host antibodies) are highlighted here.

Global differences in changes in the numbers of population-adjusted daily test-positive cases (NPDP) and deaths (NPDD) by COVID-19 were analyzed for 49 countries, including developed and developing countries. The changes as a proportion of national population were compared, adjusting by the beginning of test-positive cases increase (BPI) or deaths increase (BDI). Remarkable regional differences of more than 100 fold in NPDP and NPDD were observed. The trajectories of NPDD after BDI increased exponentially within 20 days in most countries. Machine learning analysis suggested that NPDD on 30 days after BDI was the highest in developed Western countries (1180 persons per hundred million), followed by countries in the Middle East (128), Latin America (97), and Asia (7). Furthermore, in Western countries with positive rates of the PCR test of less than 7.0%, the increase in NPDP was slowing-down two weeks after BPI, and subsequent NPDD was only 15% compared with those with higher positive rates, which suggested that the situation of testing might have affected the velocity of COVID-19 spread. The causes behind remarkable differences between regions possibly include genetic factors of inhabitants because distributions of the race and of the observed infection increasing rates were in good agreement globally.

Since 2015, outbreaks of foot-and-mouth disease (FMD) in the Middle East have been caused by a new emerging viral lineage, A/ASIA/G-VII. In-vitro vaccine matching data indicated that this virus poorly matched (low r1-value) with vaccines that were being used in the region as well as most other commercially available vaccines. The aim of this study was to assess the performance of two candidate vaccines against challenge with a representative field virus from the A/ASIA/G-VII lineage. The results from an initial full dose protection study provided encouraging data for the A/MAY/97 vaccine, while the A22/IRQ/64 vaccine only protected 2/7 vaccinated animals. In view of these promising results, this vaccine was tested in a potency test (PD50) experiment in which 5 cattle were vaccinated with a full dose, 5 cattle with a 1/3 dose and 5 cattle with a 1/9 dose of vaccine. Vaccines were prepared as would be done during an emergency vaccination campaign using a double oil emulsion adjuvant. At 21 days post vaccination these vaccinated cattle and 3 control cattle were subsequently challenged intradermolingually with a field isolate from the A/ASIA/G-VII lineage. All cattle from the full vaccine dose, 4 cattle from the 1/3 vaccine dose and 2 cattle from the 1/9 vaccine dose were clinically protected against challenge with FMDV A/ASIA/G-VII, resulting in a heterologous potency of 6.5 PD50/dose. These data support previous studies showing that a high potency emergency vaccine can protect against clinical disease when challenged with a heterologous strain of the same serotype. Not only the r1-value of the vaccine, but also the homologous potency of a vaccine should be taken into account when advising vaccines to control an outbreak.

Immense challenges arise in the Quality Assurance area due to contemporary development in Internet of Things (IoT) technology. Current issues are mainly related to test coverage, test diversity, IoT Stability, Use of Cellular Networks in IoTs, IoT Devices updates, Security, Data Integration, and interoperability. In this paper, we present all those issues with suggestions for tackling those issues.

The aim of this study was to identify the differences in functional fitness and quality of life among women over 60 years of age depending on their level of objectively measured physical activity (PA) according to Global Recommendations on Physical Activity for health. The study used cross-sectional design with 213 volunteered women over 60 years of age. Physical activity was monitored for 7 days of the week using Actigraph Gt3x monitor. The Senior Fitness Test battery and Hand-grip strength tests were performed to assess functional fitness. Quality of life was self-reported using short version of WHOQOL-brief questionnaire. Women who met the PA recommendations achieved slightly better results in most functional tests and all domain of quality of life. The significant differences were found in upper body strength, dynamic balance and social relationships domain of quality of life. Physical activity programs developed on the basis of WHO recommendations have the potential to improve functional capacity and quality of life. However, further experimental studies in this area are required.

The increased consumption of food requiring thermoformed packaging means that the packaging industry demands customized solutions in terms of shapes and sizes to make the packaging unique. In particular, the food industry increasingly requires more transparent packaging, with greater clarity and a better presentation of the product features they contain. However, in turn, the differentiation of products is sought through the geometry and final finish of the product, as well as the arrangement of food inside the packaging. In addition, these types of packaging usually include ribs in the walls to improve physical properties, however they also affect the final aesthetics of the product. In accordance with this, this research study analyses by studying the mechanical properties of different relief geometries that can affect not only the aesthetics but also their strength. For this purpose, tensile and compression tests have been carried out. The results provide comparative data on the reliefs studied and show that there are different shapes, sizes and layout.

Impact load was applied to hardened cement paste (HCP) specimens using a gas gun to investigate microscopic changes in the specimens and develop a better response model of concrete subjected to impact load. Plasma emission was observed at the moment of impact at 420 m/s and the colour of the portion near the impact point turned brighter. This brighter portion was analysed, and it was observed that the pore structure was coarser compared to the other portion; however, the results of thermogravimetry and X-ray diffraction analysis were similar. A possible reason is that the generated heat was instantaneous and the rate of the temperature increase in the HCP decreased due to evaporation of water in the HCP. These results indicate that during impact at a few hundred m/s, porosity increase due to heat effect is more dominant than porosity decrease due to mechanical compaction.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

The Medi-test system we developed was motivated by the large number of resources available for the medical domain, as well as the number of tests needed in this field (during and after the medical school) for evaluation, promotion, certification, etc. Generating questions to support learning and user interactivity has been an interesting and dynamic topic in NLP since the availability of e-book curricula and e-learning platforms. Current e-learning platforms offer increased support for student evaluation, with an emphasis in exploiting automation in both test generation and evaluation. In this context, our system is able to evaluate a student’s academic performance for the medical domain. Using as input medical reference texts and supported by a specially designed medical ontology, Medi-test generates different types of questionnaires for Romanian language. The evaluation includes 4 types of questions (multiple-choice, fill in the blanks, true/false and match), can have customizable length and difficulty and can be automatically graded. A recent extension of our system also allows for the generation of tests which include images. We evaluated our system with a local testing team, but also with a set of medicine students, and user satisfaction questionnaires showed that the system can be used to enhance learning.

The stability of twenty seven composts and organic substrates (including raw, less stable and stable materials) was assessed using two different liquid phase tests were carried out. One of the tests was introduced in 1998 and was based on the calculation of a Specific Oxygen Uptake Rate (SOUR). The newly introduced liquid phase test presented here is simpler to set-up and to perform that the older liquid phase test. It is based on the quantification of oxygen consumption in the headspace of a BOD bottle that contains the liquid-solid solution. The results indicate that a marginal correlation does exist between the main indices calculated from both tests. The correlation was stronger for the indices calculated for stable-processed organics than for the raw (unprocessed materials). The SOUR ranged from 1520 to 3650mg O₂/kg VS-h for the raw materials and from 110 to 1150 mg O₂/kg VS-h for the processed materials, respectively. The corresponding stability rate related index (LSRI₂₄) of the new liquid phase test introduced here ranged from 240 to 1180 mg O₂/dry kg-h for the raw materials and from 64 to 792 mg O₂/dry kg-h for the processed ones.

Within the field of guilt and shame, two competing perspectives have been advanced. The first, the social-adaptive perspective, proposes that guilt is an inherently adaptive emotion and shame is an inherently maladaptive emotion; thus, those interested in moral character development and psychopathology should work to increase an individual’s guilt-proneness and decrease an individual’s shame-proneness. The functionalist perspective, in contrast, argues that both guilt and shame can serve a person adaptively or maladaptively—depending on the situational appropriateness, duration, intensity, and so forth. This paper reviews the research conducted supporting both positions, critiques some issues with the most widely used guilt- and shame-proneness measure in the social-adaptive research (the TOSCA), and discusses the differences in results found when assessing guilt and shame at the state versus trait level. The conclusion drawn is that although there is broad support for the functionalist perspective across a wide variety of state and trait guilt/shame studies, the functionalist perspective does not yet have the wealth of data supporting it that has been generated by the social-adaptive perspective using the TOSCA. Thus, before a dominant perspective can be identified, researchers need to (1) do more research assessing how the social-adaptive perspective compares to the functionalist perspective at the state level, and (2) do more trait research within the functionalist perspective to compare functionalist guilt- and shame-proneness measures with the TOSCA.

The main objective of this paper is to find a close link between the adaptive level of significance, presented here, and the sample size. We, statisticians, know of the inconsistency, or paradox, in the current classical tests of significance that are based on p-value statistics that is compared to the canonical significance levels (10%, 5% and 1%): "Raise the sample to reject the null hypothesis" is the recommendation of some ill-advised scientists! This paper will show that it is possible to eliminate this problem of significance tests. The Bayesian Lindley's paradox – "increase the sample to accept the hypothesis" – also disappears. Obviously, we present here only the beginning of a possible prominent research. The intention is to extend its use to more complex applications such as survival analysis, reliability tests and other areas. The main tools used here are the Bayes Factor and the extended Neyman-Pearson Lemma.

Co-integration and Causality was built to conduct studies on causality relation between carbon intensity and coal consumption leading to providing important basis for the transition to a low carbon economy. The EG two-step method was performed to study the relation between carbon intensity and coal consumption of China during 1990-2015 and the co-integration and Granger test was constructed to build up the co-integration and error correction models for analysis of the interaction between carbon intensity and coal consumption. The results showed that in long term there is a stable co-integration relation and a positive correlation between carbon intensity and coal consumption; whereas fluctuations exist in short term and there is a one-way Granger causality of carbon intensity with respect to coal consumption.

The COVID-19 pandemic has created huge damage to society and brought panics around the world. Such panics can be ascribed to the seemingly deceptive features of the COVID-19: compared to other deadly viral outspreads, it has medium transmission and mortality rates. As a result, the severity of the causative coronavirus, SARS-CoV-2, was deeply underestimated by the society at the beginning of the COVID-19 outbreak. Based on this, in this review, we define the viruses with features similar to those of SARS-CoV-2 as the Panic Zone viruses. To contain those viruses, accurate and fast diagnosis followed by effective isolation and treatment of patients are pivotal at the early stage of virus breakouts. This is especially true when there is no cure or vaccine available for a transmissible disease, which is the case for current COVID-19 pandemic. As of January 2021, more than two hundred kits for the COVID-19 diagnosis on the market are surveyed in this review, while emerging sensing techniques for SARS-CoV-2 are also discussed. It is of critical importance to rationally use these kits for the efficient management and control of the Panic Zone viruses. Therefore, we discuss guidelines to select diagnostic kits at different outbreak stages of the Panic Zone viruses, SARS-CoV-2 in particular. While it is of utmost importance to use nucleic acid-based detection kits with low false negativity (high sensitivity) at the early stage of an outbreak, the low false positivity (high specificity) gains its importance at later stages of the outbreak. When a society is set to reopen from the lock-down stage of the COVID-19 pandemic, it becomes critical to have antibody based immunoassay kits with high specificity to identify people who can safely return to the society after their recovery of SARS-CoV-2 infections. Given that the emergence of mutant viruses at the beginning of 2021 has complicated current battle against the COVID-19, we also discussed approaches and guidelines to detect viral mutants in the middle of the second wave of the pandemic that started at the end of 2020. Finally, since a massive attack from a viral pandemic requires a massive defense from the whole society, we urge both government and private sectors to research and develop more affordable and reliable point-of-care testing (POCT) kits, which can be used massively by the general public (and therefore called as massive POCT) to contain Panic Zone viruses in future.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

In order to study the way how to improve the spatial action of precast monolithic composite floor slabs, and would replace the cast-in-place surface layer for reduce the weight of structure, using pseudo-dynamic tests on 1/4 scale models of two-span and three-story frame structure. The lateral load tests compared the stresses and displacements with cast-in-place floor frame-shear wall structure (SJ1) and precast monolithic floor frame-shear wall structure with X horizontal braces at the bottom of the floor (SJ2). The results show the X horizontal braces can improve the spatial action. Structural integrity (SJ2) as well as the effective transmission of the horizontal force can be ensured by additional X bracing at the bottom of the rigidity of the floor without cast-in-place concrete topping. The results show that X horizontal braces more effectively transfer horizontal, which provides a beneficial reference for similar research.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

The objective of this study was to investigate the liquefaction resistance of chemically improved sandy soils in a straightforward and accurate manner. Using only the existing experimental databases and artificial intelligence, the goal was to make predictions without conducting physical experiments. Emphasis was placed on the significance of data from 20 loading cycles of cyclic undrained triaxial tests to determine the liquefaction resistance and the contribution of each explanatory variable. Different combinations of explanatory variables were considered. Regarding the predictive model, it was observed that a case with the liquefaction resistance ratio as the dependent variable and other parameters as explanatory variables yielded favorable results. In terms of exploring combinations of explanatory variables, it was found advantageous to include all variables as doing so consistently resulted in a high coefficient of determination. The inclusion of the liquefaction resistance ratio in the training data was found to improve the predictive accuracy. In addition, the results obtained when using a linear model for the prediction suggested the potential to accurately predict the liquefaction resistance using historical data.

To win a taekwondo competition, more points must be scored, and the key to scoring points is to improve the motor performance of the kick. The wing kick is an offensive and defensive maneuver. Core stability appears to be important for improving athletic performance, but the specific relationship and effect of core stability on athletic performance in the aerial phase of taekwondo is unclear. The aim of this study was to investigate the relationship between core stability and athletic performance in taekwondo in order to provide appropriate theoretical support for training and to help coaches and athletes to improve athletic performance. A total of 16 subjects (height: 167.34±9.2 cm; weight: 61±8.96 kg; age: 24.7±3.25 years) were studied. Data were captured using 13 infrared cameras at 120Hz, kinematic and kinetic data were captured using a motivated motion capture system, and the data were exported to Visual3D in order to calculate the execution time of the aerial phase, the angular momentum of the left lower extremity, and MVC analysis of the EMG using EMG works. The core stability level of the subjects were measured using the Sahrmann Core Stability Test (SCST) to correlate with the other data, and then the subjects were grouped according to their core stability levels and the data from both groups were analyzed with t-tests. Results During the double fly lifting of aerial segments, SCST levels showed a very strong negative correlation with execution time (r= -0.739) and there was a statistically significant difference in execution time between high and low SCST levels (p < 0.001), and the desired negative correlation was also seen in lower limb angular momentum X-axis (thigh r= -0.6294, shank r= -0.536, foot r= -0.6175), especially in the X-axis. The left rectus femoris (LRF) data had greater activation in the low SCST group(p=0.0019*). Through this experiment, we found that athletes with high core stability had faster execution times, lower angular momentum, and higher core muscle activation. Therefore, we conclude that incorporating core stability training into taekwondo training has the potential to improve kicking performance.

A homogenized, supersaturated Al-Zn-Mg-Zr alloy was processed by severe plastic deformation (SPD) using high-pressure torsion (HPT) technique for different revolutions at room temperature to get ultrafine-grained (UFG) microstructure. The microstructure and mechanical properties of the UFG samples were then studied by transmission electron microscopy (TEM), differential scanning calorimetry (DSC), as well as by tensile and hardness measurements. Emphasis was placed on the effect of shear strain on the evolution of microstructure of the investigated alloy. Experimental results have shown a very interesting evolution of the decomposed microstructure in a wide range of shear strains imposed by HPT. While the global properties, such as the average grain size (~200 nm) and hardness (~2.2 GPa) appeared unchanged, the local microstructure was continuously transformed. After 1 turn of HPT, the decomposed UFG structure contains relatively large precipitates inside grains. In the sample processed by 5 turns in HPT, segregation of Zn atoms into grain boundaries (GBs) can also be observed. After 10 turns, more Zn atoms have segregated into GBs and only smaller size precipitates can be observed inside grains. The intensive segregation of solute atoms into GBs may significantly affect the ductility of the materials, leading to its ultralow-temperature superplasticity. Our findings pave the way for achieving advanced microstructural and mechanical properties in nanostructured metals and alloys by engineering their precipitation and segregation by means of applying different HPT regimes.

Background: Cognitive for patients with neurocognitive disorders are mostly measured by Montreal Cognitive Assessment (MoCA) and Visual Cognitive Assessment Test (VCAT) as screening tools. These cognitive scores are usually left skewed and the results of association analysis might not be robust. This study aims to study the distribution of the cognitive outcomes and to discuss potential solutions. Materials and Methods: The inverse transformed cognitive outcomes are modelled using different statistical distributions. Robustness of the proposed models are checked under different scenarios: with intercept only, models with covariate, with and without bootstrapping. Results: Main results were based on VCAT score, and validated via MoCA score. Findings suggested that the inverse transformation method improves modelling the cognitive scores compared to the conventional methods using the original cognitive scores. Association of baseline characteristics (age, gender and years of education) and the cognitive outcomes were reported as estimates and 95% confidence intervals. Bootstrap methods improved the estimate precision and the bootstrapped standard errors of the estimates are more robust. Cognitive outcomes are widely analyzed using linear regression models with default normal distribution as a conventional method. We compared the results of our suggested models with the normal distribution under various scenarios. Goodness-of-fit measurements were compared between proposed models and conventional methods. Conclusions: The findings support the use of the inverse transformation method to model the cognitive outcomes instead of the original cognitive scores for early stage neurocognitive disorders where the cognitive outcomes are left skewed.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99±0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile strength in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile strength to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

In this paper, we propose a method for the generation of simulation test scenarios for autonomous driving. Based on the requirements of standard regulatory test scenarios, we can generate virtual simulation scenarios and functional scenario libraries for autonomous driving, which can be used for simulation verification of different ADAS functions. Firstly, the design operation domain (ODD) of the functional scenario is selected and the weight values of the ODD elements taken are calculated; then a combination test algorithm based on parameter weights is improved to generate autonomous driving virtual simulation test cases for the ODD elements, which can effectively reduce the number of generated test cases compared with the traditional combination test algorithm; then the traffic participant elements under each test case are Then, the values of the subelements under the traffic participant element in each test case are sampled and clustered to obtain hazard specific scenarios. Finally, the specific scenarios are applied to the automatic emergency braking (AEB) system on the model-in-the-loop (MIL) testbed to verify the effectiveness of this scenario generation method.

Febrile seizures in early childhood can lead to developmental disorders in the CNS. However, the specific mechanisms behind the impact of febrile seizures on the developing brain are not well-understood. To address this gap in knowledge, we employed a hyperthermic model of febrile seizures in 10-day-old rats and tracked their development over two months. Our objective was to determine the degree to which the properties of the hippocampal glutamatergic system are modified. We analyzed whether pyramidal glutamatergic neurons in the hippocampus die after febrile seizures. Our findings indicate that there is a reduction in the number of neurons in various regions of the hippocampus in the first two days after seizures. The CA1 field showed the greatest susceptibility, and the reduction in the number of neurons in post-FS rats in this area appeared to be long-lasting. Electrophysiological studies indicate that febrile seizures cause a reduction in glutamatergic transmission, leading to decreased local field potential am-plitude. This impairment could be attributable to diminished glutamate release probability as evidenced by decreases in frequency of miniature excitatory postsynaptic currents and increases in pair-pulse ratio of synaptic responses. We also found higher threshold current causing hindlimb extension in the maximal electroshock seizure threshold test of rats 2 months after febrile seizures compared to control animals. Our research suggests that febrile seizures can impair glutamatergic transmission, which may protect against future seizures.

This study delves into the atmospheric corrosion behavior of chromium-free complex-phase steel (CP), specifically investigating the influence of wet/dry frequency and ratio in cyclic corrosion tests (CCT). The study employs a modified ISO 14993 standard CCT method, which involves salt spray, dry, and wet stages. After 15 and 30 CCT cycles, mass loss, maximum corrosion depth, and corrosion products were analyzed to gain insights into corrosion mechanisms. In general, increasing the frequency and wet/dry stage ratio in CCT extends the time for autocatalytic reactions to occur, leading to accelerated localized CP corrosion and increased pitting factors. However, as the rust layer thickens, uniform corrosion may also intensify, so careful considerations are necessary. This study underscores the importance of controlling the frequency and ratio of wet/dry stages in CCT for effectively analyzing localized corrosion behavior in specimens.

This study examined the efficacy of essential oil (EO) obtained from the Australian native plants, lemon myrtle (Backhousia citriodora) (LM) to inhibit Penicillium digitatum by in vitro agar diffusion and vapor assay, and in inoculated oranges. Gas chromatograph/mass spectrometry analysis revealed the main constituent of LM EO as citral. Pure citral was also included in the experiment for com-parison. LM EO at 1, 2, 3, 4 and 5 µL disc-1 in the in vitro tests significantly inhibited fungal growth compared to the non-treated control. Moreover, LM EO at 4 and 5 µL disc-1 in both the assays completely inhibited fungal growth similar to its main component of citral. Inoculated oranges dipped in 1000 μL L-1 LM EO solutions for 5, 10, 15 and 30 sec showed significantly lower fungal wounds compared to control. While higher dipping times generated slight rind injury, a 5 and 10 sec dip did not cause any injury to the fruit rind. The quality assessments and sensory evaluations also revealed that the addition of LM EO did not adversely affect the quality and taste of the oranges. These findings suggest LM EO as an alternative to synthetic fungicides to inhibit wastage in citrus during storage.

To control the COVID-19 pandemic, many countries implemented vaccination and imposed societal restrictions both at the national level and for international travel. As a check of the corona status, a COVID pass has been issued. A COVID pass could be obtained when fully vaccinated against COVID-19, having recovered from a documented COVID-19 episode, or a recent (24-48 hours) negative SARS-CoV-2 antigen test. A global analysis of SARS-CoV-2 immune status (determined by past infection and/or vaccination), vaccination rates, as well as societal restrictions in controlling the COVID-19 pandemic is presented.

Functionally graded materials (FGM) have attracted considerable attention in the field of composite materials and rekindled interest in research on composite materials, due to their unique mechanical response achieved through material design and optimization. Compared to conventional composites, FGMs offer several advantages and exceptional properties, including improved deformation resistance, improved toughness, lightness properties, and excellent recoverability. This study focused on the production of functionally graded (FG) polymer materials by additive manufacturing (AM) method. FG structures were produced by the Fused Deposition Modeling (FDM) method using Acrylonitrile benzidine styrene (ABS) and Polylactic acid (PLA) materials and tensile tests were performed according to ASTM D638. The effects of different layer thicknesses, volume ratios, and total thicknesses on mechanical behavior were investigated. In addition, tensile tests were carried out by producing single-layer samples at certain volume ratios to create a numerical model with the Finite element method to verify the experimental data. As a result of this study, it is presented that the FG structure produced with FDM improves mechanical behavior.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

Silicon-based microchannel technology offers unmatched performances for cooling high energy physics silicon-pixels detectors. Although Si-Si direct bonding, used for the fabrication of cooling plates, meets the stringent requirements of this application, in particular high-pressure resistance (~200 bar), it is reported to be a challenging and expensive process. In this work, we have evaluated two alternative bonding methods towards a more cost-effective fabrication process: Si-Glass-Si anodic bonding (AB) with a thin-film glass and Au-Au thermocompression (TC). The bonding strength of the two methods were evaluated with destructive pressure burst tests (0 - 690 bar) on test structures, each made of a 1×2 cm² silicon die etched with a tank and an inlet channel and sealed with a plain silicon die using AB or TC bonding. The pressure resistance of the structures was measured to be higher for the TC sealed samples (max. 690 bar) than for the AB ones (max. 530 bar) but less reproducible. The failure analysis indicates that the AB structure resistance is limited by the adhesion force of the deposited layers. Nevertheless, both the TC and AB methods provided sufficient bond quality to hold the high pressure required for the high energy physics pixel detectors cooling application.

This article introduces simulations of theoretical material with controlled properties for the evaluation of the effect of key parameters, as volumetric fractions, elastic properties of each phase and transition zone on the effective dynamic elastic modulus (Ed). The accuracy level of classical homogenization models was checked regarding the prediction of Ed. Numerical simulations were performed with finite element method (FEM) for evaluations of the natural frequencies and their correlation with Ed, through frequency equations. An acoustic test validated the numerical results and obtained the elastic modulus of concretes and mortars at 0.3, 0.5 and 0.7 water-cement ratios (w/c). Hirsch calibrated according to the numerical simulation (x = 0.27) exhibited a realistic behavior for concretes of w/c = 0.3 and 0.5, with 5% error. Nevertheless, for w/c = 0.7, Ed approached Reuss model, similarly to theoretical triphasic materials. Hashin-Shtrikman bounds is not perfectly applied to theoretical biphasic materials under dynamic situations.

Maximal heart rate (HRmax) is a widely used measure of cardiorespiratory fitness. Prediction of HRmax is an alternative to cardiopulmonary exercise testing (CPET), but its accuracy among endurance athletes (EA) requires evaluation. This study aimed to externally validate HRmax prediction models in the EA independently for running and cycling CPET. 4043 runners (age=33.58 (8.12) years; 83.53% males; BMI=23.66 (2.54) kg·m−2) and 1026 cyclists (age=36.88 (9.03) years; 89.67% males; BMI=24.04 (2.65) kg·m−2) underwent maximum CPET. Student t-test, mean absolute percentage error (MAPE), mean absolute error (MAE), and root mean square error (RMSE) were applied to externally validate 8 running and 5 cycling HRmax equations. HRmax was 184.60 (9.79) beats·min−1 and 182.66 (10.28) beats·min−1 respectively for running and cycling, p=0.001. Measured and predicted HRmax differed significantly (p=0.001) for 9 of 13 (69.23%) models. HRmax was overestimated by 8 (61.54%) and underestimated by 5 (38.46%) formulae. Overestimated HRmax ranged 0.08-4.94 beats·min−1 and underestimated HRmax ranged 0.03-4.90 beats·min−1. MAE and RMSE were 0.18-4.94 beats·min−1 and 9.13-10.47, respectively. MAPE ranged 3.95-4.69%. Prediction models do not allow for accurate estimation of HRmax. HRmax was more often underestimated than overestimated. Predicted HRmax can be implemented for EA as a supplemental method but CPET is the preferable approach.

With Direct Laser Writing (DLW) maturing in all aspects as a manufacturing technology a toolset for quality assurance must be developed. In this work we want to introduce a first of its kind test artifact. Test artifacts are standardized 3D models with specific geometric feature to evaluate the performance of writing parameters. Test artifacts are already common in other 3D additive manufacturing technologies e.g. Selective Laser Melting. The test artifact introduced in this work was developed in particular to accommodate 1) the high geometrical resolution of DLW structures and 2) the limited possibilities to examine the resulting structure. Geometric accuracy, surface adhesion as well as confocal raman spectroscopy results were considered when evaluating the design of the test artifact. We will explain the individual features and design considerations of our DLW test artifact. The difference between two slicers, Cura and 3DPoli, and the implications on measured feature sizes and the general shape is quantified. The measured geometries are used to derive a general design guide for a specific combination of photoresist, laser power and scanning speed and to analyse the geometric accuracy of a structure produced using these guidelines.

Climate change is a phenomenon that makes the climate system of a given region to be more unpredictable and increases the risk of water-related problems. GCMs under the new CMIP6 framework holds several climate models with many improvements as compared to past similar efforts. The improvements are mainly in the number of scenarios formulated, setup, parametrization, and resolution. In this study, 10 downscaled climate models from CMIP6 are evaluated by applying statistical and data mining tools and are ranked based on their capability to describe the historical observed series. The result of the analysis showed that the outputs of the MPI-ESM1-2-HR model have a good overall ranking among those 10 models. The output of this top-ranked model is used to understand future climate over UASB after properly bias-corrected using the QM method. Results of the bias correction step show that average annual precipitation has shown an increment of 6.5\% in the middle (SSP2-4.5) and 10.3\% in the worst (SSP5-8.5) case scenarios for the mid-century (2040 - 2069). Similarly, for the end of the century (2070 - 2099) an increment of 4.7\% and 17.5\% was predicted for the two scenarios respectively. Whereas average annual maximum temperature series showed an increment of 1.5 $\degree C$ for middle and 2.6 $\degree C$ for the worst case in the mid-century. At the same time, an increment of 2.2 $\degree C$ and 3.5 $\degree C$ were predicted for the end of the century similarly for those scenarios. Furthermore, it was predicted that the average annual minimum temperature series will have an increment of 2.6 $\degree C$ and 3.1 $\degree C$ for mid-century and 3.1 $\degree C$ and 4.7 $\degree C$ for the end century for the two scenarios respectively. An increase in precipitation with increased land degradation problems in the sub-basin increases the risk of flood events in the future.

Background and Aims. Most research on Parkinson's disease (PD) focuses on describing symp-toms and movement characteristics. Studies rarely focus on the early detection of PD and the search for suitable markers of a prodromal stage. Early detection is important, so treatments that may potentially change the course of the disease can be attempted early on. While gait disturb-ances are less pronounced in the early stages of the disease, the prevalence, and severity increase with disease progression. Therefore, postural instability and gait difficulties could be identified as sensitive biomarkers. The aim was to evaluate the discriminatory power of the Trail-Walking Test (Schott, 2015) as a potential diagnostic instrument to improve the predictive power of the clinical evaluation concerning the severity of the disease and record the different aspects of walking. Methods. 20 older healthy (M = 72.4 years, SD = 5.53) adults and 46 older adults with PD and the motor phenotypes postural instability/gait difficulty (PIGD; M = 69.7 years, SD = 8.68) and tremor dominant (TD; M = 68.2 years, SD = 8.94) participated in the study. The participants performed a motor-cognitive dual task (DT) of increasing cognitive difficulty in which they had to walk a given path (condition 1), walk to numbers in ascending order (condition 2), and walk to numbers and letters alternately and in ascending order (condition 3). Results. With an increase in the cognitive load, the time to complete the tasks (seconds) become longer in all groups, F(1.23, 73.5) = 121, p < .001, ɳ2p = .670. PD-PIGD shows the longest times in all conditions of the TWT, F(2, 60) = 8.15, p < .001, ɳ2p = .214. Mutual interferences in the cognitive and motor domain can be observed. How-ever, clear group-specific patterns cannot be identified. A differentiation between the motor phenotypes of PD is especially feasible with the purely motor condition (TWT-M; AUC = . 685, p = 0.44). Conclusions. PD patients with PIGD must be identified by valid, well-evaluated clinical tests that allow a precise assessment of the disease's individual fall risk, the severity of the dis-ease, and the prognosis of progression. The TWT covers various aspects of mobility, examines the relationship between cognitive functions and walking, and enables differentiation of the motor phenotypes of PD.

Evaluation of the usefulness of [18F]FDG-PET/CT in the short-term follow-up of patients admitted for COVID-19 pneumonia and to explore the association of findings with clinical prognostic markers. Prospective study included 20 patients admitted to hospital with COVID-19 pneumonia between November 2020 and March 2021. Clinical and laboratory test findings were gathered at admission, 48-72h post-admission, and 2-3 months post-discharge. [18F]FDG-PET/CT and respiratory function tests were performed at 2-3 months post-discharge. Lung volumes (TLC), spirometry (FVC, FEV1), lung diffusion capacity for carbon monoxide (DLCO), and respiratory muscle strength were measured. PET/CT images were qualitatively and semi-quantitatively interpreted. Volumetric [18F]FDG-PET/CT results were correlated with laboratory test and respiratory parameters. Eleven [18F]FDG-PET/CT (55%) were positive. The main finding was hypermetabolic lymphade-nopathy in the mediastinum (90.9%). SUVpeak of the target mediastinum lesion was correlated with neutrophil and lymphocyte counts. Eleven (55%) patients had impaired respiratory function, most frequently a reduced DLCO (35%). SUVpeak was positively correlated with %predict-ed-DLCO values. Pulmonary TLG was negatively correlated with %predicted-DLCO and TLC values. In the short-term follow-up of patients hospitalized for COVID-19 pneumonia, [18F]FDG-PET/CT findings revealed significant detectable inflammation in lungs and mediastinal lymph nodes that correlated with pulmonary function impairment in more than half of the patients.

Poplar is a globalized commercial tree species that supports humanity's economy, energy, and ecology. To evaluate the twelve hybrid Populus euramericana genotypes developed in China, a total of six locations were selected for the test, comprising four climatic types and three soil kinds. The objective of this study is to characterize the early stages of Populus euramericana growth and test locations; to identify good genotypes for stable and high yield that may be encouraged; and to offer practical experience and technical assistance for further breeding of Populus euramericana. Main research methods include the statistical description of tree heights and diameter at breast heights[DBH], the establishment of a mixed effect model to analyze the genotype and environmental interaction effect [G×E], the use of best linear unbiased prediction[BLUP] values as GGE biplots to achieve visual screening, and the calculation of genetic parameters. Results show that the genotype effect [G], the environmental effect [E], and the G×E is significant; the BLUP value has a strong correspondence with the observed value; the goodness of fit of all biplots can explain more than 85% of the variation; broad-sense heritability of tree height and DBH is 0.13 and 0.3, type-B correlation is 0.36 and 0.65; G5, G7, G4 and G9 are excellent genotypes with high yield and stability; using these four genotypes tree height and DBH can get 3.35% and 0.81% genetic gains.The study concludes as follows: Rank-change interaction and scale-effect interaction were distinctly occurred. The G, E, and G×E all had a significant effect on the growth of poplar trees during their early stage. G4, G5, G7, and G9 genotypes have favorable development characteristics. N146 is a great source of paternal genetics.

Urban air quality is increasingly being studied as a fraction of the world's population is now living in megacities. In this study, particulate matter (PM) along Taft Avenue, Manila, Philippines, is investigated in terms of its ability to induce genetic damage on human peripheral blood lymphocytes (PBL). Size-segregated roadside air samples were obtained from 2015-2016 near the university gate and analyzed using in vitro micronucleus and cytokinesis-block proliferation tests. While cellular proliferation was unaffected by 0 – 0.1 kg·m-3 of PM1.0 and PM2.5, PBL cells treated with PM2.5 displayed significantly higher micronucleus count (p = 0.03) compared to the cells treated with PM1.0. Atomic Absorption Spectroscopy revealed greater amounts of Cd, Ca, Pb, K, Na, and Zn in PM2.5 compared to PM1.0. The results indicate the differences in composition of the two size fractions of air particulates are associated with their genotoxicities.

Sentinel-1A/B radar remote sensing data were applied for the first time to determine the sixth nuclear test, its underground explosion h-bomb location and affected zone in North Korea, on September 3, 2017. Location of epicenters nuclear test were found according to line-of-sight displacement images via its maximum value. Line-of-sight displacement images were obtained by processing in the GMTSAR package in the VirtualBox virtual machine of the Linux Ubuntu 16.04 operation system. In this research, three scenes Sentinel-B data with descending orbits were considered, one after and two before the event (the nuclear test date) scene were used.

A sufficient amount of tissue sample is required to perform next-generation sequencing (NGS) with a high success rate, but the majority of patients with advanced non-small-cell lung cancer (NSCLC) are diagnosed with small biopsy specimens. Biopsy samples were collected from 184 patients with bronchoscopically diagnosed NSCLC. The tissue surface area, tumor cell count, and tumor content rate of each biopsy sample were evaluated. The impact of the cut-off criteria for the tissue surface area (≥ 1 mm2) and tumor content rate (≥ 30%) on the success rate of Oncomine Dx Target Test (ODxTT) was evaluated. The mean tissue surface area of the transbronchial biopsies was 1.23 ± 0.85 mm2 when small endobronchial ultrasonography with a guide sheath (EBUS-GS) was used, 2.16 ± 1.49 mm2 with large EBUS-GS, and 1.81 ± 0.75 mm2 with endobronchial biopsy (EBB). The proportion of samples with a tissue surface area of ≥ 1 mm2 was 48.8% for small EBUS-GS, 79.2% for large EBUS-GS, and 78.6% for EBB. Sixty-nine patients underwent ODxTT. The success rate of DNA sequencing was 84.1% and that of RNA sequencing was 92.7% over all patients. The success rate of DNA (RNA) sequencing was 57.1% (71.4%) for small EBUS-GS (n = 14), 93.4% (96.9%) for large EBUS-GS (n = 32), 62.5% (100%) for EBB (n = 8), and 100% (100%) for endobronchial ultrasound-guided transbronchial needle aspiration (EBUS-TBNA) (n = 15). Regardless of the device used, a tissue surface area of ≥ 1 mm2 is adequate for samples to be tested with NGS.

Is it possible to measure the dispersion of ex-ante chances (i.e. chances “before the event”) among people, be it gambling, health, or social opportunities? We explore this question and provide some tools, including a statistical test, to evidence the actual dispersion of ex-ante chances in various areas with a focus on chronic diseases. Using the principle of maximum entropy, we derive the distribution of the risk to become ill in the global population as well as in the population of affected people. We find that affected people are either at very low risk like the overwhelming majority of the population but still were unlucky to become ill, or are at extremely high risk and were bound to become ill.

Bohrnstedt’s (1969) attempt to derive a formula to compute the partial correlation coefficient and simultaneously correct for attenuation sought to simplify the process of performing each task separately. He suggested that his formula, developed from algebraic and psychometric manipulations of the partial correlation coefficient, produces a corrected partial correlation value. However, an algebraic error exists within his derivations. Consequently, the formula proposed by Bohrnstedt does not appropriately represent the value he intended it to estimate. By correcting the erroneous step and continuing the derivation based upon his proposed procedure, the steps outlined in this paper ultimately produce the formula that Bohrnstedt desired.

In recent years, many studies have highlighted the consistent finding of amoxicillin in waters destined for wastewater treatment plants, in addition to superficial waters of rivers and lakes in both Europe and North America. In this paper, the amoxicillin degradation pathway was investigated by simulating the chlorination process normally used in a wastewater treatment plant to reduce similar emerging pollutants at three different pH values. The structures of 16 isolated degradation byproducts (DPs), one of which was isolated for the first time, were separated on a C-18 column via a gradient HPLC method. Then, combining mass spectrometry (MALDI-MS/TOF) and nuclear magnetic resonance, we compared commercial standards and justified a proposed formation mechanism beginning from the parent drug. Microbial growth inhibition bioassays with Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were performed to determine the potential loss of antibacterial activity in isolated degradation byproducts. An increase of antibacterial activity in the DPs was observed compared to the parent compound.

Anomaly occurrences in hydraulic machinery may lead to massive systems shut down, jeopardizing the safety of the machinery and its surrounding human operator(s) and environment, and the severe economic implications succeeding the faults and their associated damage. Hydraulics are mostly placed in ruthless environments, where they are consistently vulnerable to many faults. Hence, not only the machines and their components are prone to anomalies, but also the sensors attached to them, which monitor and report their health and behavioral changes. In this work, a comprehensive applicational analysis of anomalies in hydraulic systems extracted from a hydraulic test rig is thoroughly achieved. Firstly, we provided a combination of a new architecture of LSTM autoencoders and supervised machine and deep learning methodologies to perform two separate stages of fault detection and diagnosis. The two phases are condensed by: the detection phase using the LSTM autoencoder. Followed by the fault diagnosis phase represented by the classification schema. The previously mentioned framework is applied to both component and sensor faults in hydraulic systems, deployed in the form of two in-depth applicational experiments. Moreover, a thorough literature review of the past decade related work for the two stages separately is successfully conducted in this paper.

Yaws is a skin debilitating disease caused by Treponema pallidum subspecies pertenue with most cases reported in children. World Health Organization (WHO) aims at total eradication of this disease through mass treatment of suspected cases followed by an intensive follow-up program. However, effective diagnosis is pivotal in the successful implementation of this control program. Recombinase polymerase amplification (RPA), an isothermal nucleic acid amplification technique offers a wider range of differentiation of pathogens including those isolated from chronic skin ulcers with similar characteristics such as Haemophilus ducreyi (H. ducreyi). We have developed a duplex RPA assay for the simultaneous detection of Treponema pallidum (T. pallidum) and H. ducreyi (TPHD-RPA). TPHD-RPA assay demonstrated no cross-reaction with other pathogens and enable detection of T. pallidum and H. ducreyi within 15 minutes at 42 oC. The duplex RPA assay was validated with 49 clinical samples from individuals confirmed to have yaws by serological tests. Compared with commercial multiplex real-time PCR, the TPHD-RPA assay demonstrated 94-95% sensitivity for T. pallidum and H. ducreyi confirmed samples, respectively and 100% specificity. This simple novel TPHD-RPA assay enables the rapid detection of both T. pallidum and H. ducreyi in yaws-like lesions. This test could support the yaws eradication programs by ensuring effective diagnosis as well as enable monitoring of eradication efforts success or failure and planning of follow-up interventions at the community level.

Silty clay modified by fly ash and crumb rubber is a kind of sustainable subgrade filler which has good anti-freeze-thaw resistance stability but wake vibration isolation performance. The objective of this study was to improve the vibration isolation of the modified soil and investigate the vibration isolation effect of the composite subgrade structure of XPS plates and the modified soil by indoor impact test. First, the vibration isolation performance of silty clay, modified soil and composite subgrade structure was respectively evaluated. Second, the effect of XPS plate’s thickness and vibration intensity on the vibration performance of the composite subgrade structure were evaluated. Third, the vibration isolation performance of the test groups under the condition of freeze-thaw cycles was assessed. The results show that the vibration isolation performance of subgrade can be effectively improved by setting XPS plates. The composite subgrade structure has certain vibration isolation effect, especially in vertical direction. Considering vibration isolation performance and costs, 5cm is the optimum XPS plates thickness. The composite subgrade structure has great vibration isolation performance under the condition of freeze-thaw cycles, so it is suitable to be applied in road subgrade in seasonal frozen regions.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

Disposable absorbent hygiene products have evolved for superior performance, enhancing the convenience of daily lives. Yet the use of disposable hygiene pads has brought safety concerns on chemical exposure, and significant efforts have been made to assess the potential risks associated with use of hygiene pads. This article intends to overview the safety assessment framework of diapers and feminine pads, which includes hazard identification, hazard characterization, exposure assessment, risk characterization, and postmarket risk management. Risk assessment of various constituents are reviewed for quantification methods and conservative estimation of exposure parameters. By reviewing the up-to-date considerations in risk assessment, we aim to provide insightful discussion on safety evaluation of current versions of disposable absorbent products. More clinical testing and postmarket surveillance are needed for continuous monitoring of potential health impacts of advanced products and constituents.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Analyzing BRCA1/2 tumor pathogenic variants (TPVs) in epithelial tubal/ovarian cancers (EOC) has become an essential part of the diagnostic workflow in many centers to guide treatment options and genetic cascade testing. However, there is no standardization of testing procedures, including techniques, gene assays, or sequencers used, and data on the execution of tumor tests remains scarce. Therefore, we evaluated characteristics of BRCA1/2 tumor testing in advanced-stage EOC with real-world national data. Pathology reports of patients diagnosed with EOC in 2019 in the Netherlands were obtained from the Dutch Pathology Registry (PALGA), and data regarding histological subtype and BRCA1/2 tumor tests were extracted. A total of 999 patients with advanced-stage EOC were included. Tumor tests were performed for 502 patients (50.2%) and BRCA1/2 TPVs were detected in 14.7%. Of all tests, 48.6% used hybrid capture techniques and 26.5% used PCR-based techniques. More than half of the tests (55.0%) analyzed other genes in addition to BRCA1/2. Overall, this study highlights the heterogeneity in the execution of BRCA1/2 tumor tests. Despite a lack of evidence of quality differences, we emphasize that adequate reporting and internal and external quality monitors are essential for high-quality implementation and execution of reliable BRCA1/2 tumor testing, which is crucial for identifying all patients with BRCA1/2 TPVs.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Microalgae are highly attractive to various industrial sectors and can serve as indicators of aquatic environmental health. An essential step for cultivating microalgae is assessing the cell density, which is traditionally performed through viable cell counting by optical microscopy (OM). However, this method has some limitations, such as the time involved in the process of counting, and the need for specialized training of laboratory personnel. Spectrophotometry is an affordable alternative, especially when applied to culture growth and toxicological tests. We chose the wavelength of 680 nm to detect the optical density (OD) of the green freshwater microalga Desmodesmus subspicatus and green the marine microalga Tetraselmis sp. The correlation between the number of cells and OD was suitable for both microalgae and accuracy was comparable to traditional OM counting. In toxicological tests, the OD technique allowed the monitoring of microalgal growth in the presence of the chemicals potassium dichromate, potassium chloride and sodium dodecyl sulfate (SDS), with results very close to those reported in the scientific literature. This study sheds light on this well-known technique, which is an important contribution since few articles have explored its potentialities and fragilities, showing the successful application to monitoring green microalgal cultures and toxicological assays.

Motivated by empirical observations, we propose a possible extension of Gibrat's law. By applying it into the random growth theory of income distribution (Gabaix, 2009), we find that the income distribution is described by a generalized Pareto-type distribution (GPD) with three parameters. We observe that there is a parameter /elta in the GPD that plays a key role in determining the shape of income distribution. By using the Kolmogorov-Smirnov test, we empirically show that, for typical market-economy countries, /elta is close to 0 significantly, such that the income distribution is characterized by a two-class pattern in which the bottom 90% of the population is approximated by an exponential distribution and the richest 1%~3% is approximated by an asymptotic power law. However, we empirically find that, for China both in planned economy period and in early stages of market reformation (from 1978 to 1990), /elta is significantly deviated from 0, such that the bottom of the population no longer conforms to an exponential distribution.

Background: Data on the benefits of rapid microbiological testing on antimicrobial consumption (AC) and antimicrobial resistance patterns(ARP) are scarce. We evaluated the impact of a protocol based on rapid techniques on AC and ARP in intensive care (ICU) patients. Methods: Retrospective pre(2018) and post-intervention(2019-21) study in ICU patients. A rapid diagnostic algorithm was applied from 2019 in patients with lower respiratory tract infection. Incidence of nosocomial infection, ARP, and AC as DDD(defined daily dose) were monitored. Results: A total of 3635 patients were included, 987(pre-intervention) and 2648(post-intervention). A median age was 60 years, 64% male, with APACHE II of 19 points and SOFA of 3 points. Overall ICU mortality of 17.2% without differences between the periods. An increase in the number of infections was observed in the post-intervention period(44.5% vs 17.9%, p<0.01), especially due to an increase in ventilator-associated pneumonia(44.6% vs 25%,p<0.001). AC decreased from 128.7 DDD in 2018 to 66.0 DDD in 2021(Rate Ratio=0.51). A recovery of P.aeruginosa susceptibility of 23% for Piperacillin/tazobactam and 31% for Meropenem was observed. Conclusion: The implementation of an algorithm based on rapid microbiological diagnostic techniques allowed a significant reduction in AC and ARP without affecting the prognosis of critically ill patients.

Low Emission Zone (LEZ) is an important mechanism to limit the negative environmental impact of traffic pollution in an urban area. Car traffic in the zone is strictly regulated to meet certain technical and environmental criteria. Such solutions of urban environment protection are gaining popularity, especially in European conurbations. Nowadays there are above 300 zones in Europe, mostly established in Italy and Germany. So far there are no LEZs in Eastern and Central European countries. However, the Warsaw authorities are just discussing launching of a LEZ in the city in 2024. According to the ongoing project, the zone is to be launched gradually, in five phases between 2024 and 2032, with the traffic criteria being tightened accordingly. The progressive emission reductions of the predominant pollutants in LEZ in consecutive phases were estimated on the basis of the Real Driving Emissions (RDE) test, carried out in 2020 by the ICCT. The gradually reduced emissions of NOx and PM were subsequently utilized as the input dataset for the regional CALPUFF model predictions, to calculate concentrations of these main traffic-induced pollutants within the LEZ area. The direct effect of the zone activation is reduction of air pollution in the urban center, which is mostly exposed to the pollution risk due to heavy traffic. Computer simulations reveal that implementation of the zone in the case of Warsaw will result in a quite significant reduction of NOx concentrations within the LEZ, such that its mean concentration in the zone becomes comparable to the rest of the conurbation. However, it will bring only a slight reduction of PM2.5 concentrations. This situation is due to the long-standing dominance of coal combustion in the Polish economy, which also applies to the urban municipal sector. As a consequence, particulate matter emissions of this sector are clearly predominant over the road traffic contribution. Balance can be achieved once the ongoing de-carbonization of the national economy has been completed.

BACKGROUND: Few studies have examined the use of immunoassay urine drug testing of cancer patients in palliative care clinics. OBJECTIVES: We examined the frequency of immunoassay urine drug test (UDT) abnormalities and the factors associated with aberrancy at a safety-net hospital palliative medicine clinic. METHODS: A retrospective review of the electronic medical records of consecutive eligible patients seen at the outpatient palliative medicine clinic in a resource-limited safety net hospital system was conducted between September 1, 2015 and December 31, 2020. We collected longitudinal data on patient demographics, UDT findings, and potential predictors of aberrant results. RESULTS: Of the 913 patients in the study, 500 (55%) underwent UDT testing, with 455 (50%) having the testing within the first three visits. Among those tested within the first three visits, 125 (27%) had aberrant UDT results; 44 (35%) of these 125 patients were positive for cocaine. In a multivariable regression model analysis of predictors for aberrant UDT within the first 3 visits, non-Hispanic White race (odds ratio [OR]=2.13; 95% confidence interval [CI]: 1.03-4.38; p=0.04), history of illicit drug use (OR=3.57; CI: 1.78-7.13; p< 0.001), and history of marijuana use (OR=7.05; CI: 3.85-12.91; p< 0.001) were independent predictors of an aberrant UDT finding. CONCLUSION: Despite limitations of immunoassay UDT, it was able to detect aberrant drug taking behaviors in a significant number of patients seen at a safety net hospital palliative care clinic, including cocaine use. These findings support universal UDT monitoring and utility of immunoassay-based UDT in resource limited settings.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

The acetylcholinesterase-inhibitory potential of the oleanane-type triterpenes and their glycosides from the Terminalia arjuna (Combreatceae) bark, i.e. arjunic acid, arjunolic acid, arjungenin, arjunglucoside I, sericic acid, and arjunetin, is presented. The studies are based on the in silico pharmacokinetic and biomimetic studies, the acetylcholinesterase (AChE) inhibitory activity tests, and the molecular docking research. Based on the calculated pharmacokinetic parameters, arjunetin and arjunglucoside I are indicated as able to cross the blood-brain barrier. The compounds of interest exhibit marked acetylcholinesterase inhibitory potential, which was tested in the TLC bioautography test. The longest time to reach brain equilibrium is observed for both the arjunic and arjunolic acids and the shortest one for arjunetin. All compounds exhibit high and relatively similar magnitude of binding energies, varying from ca. -15 to -13 kcal/mol. The superposition of the most favorable positions of all ligands interacting with AChE is analyzed. The correlation between the experimentally determined IC50 values and the steric parameters of the molecules is investigated. The inhibition of the enzyme by the analyzed compounds shows their potential to be used as cognition enhancing agents. For the most potent compound (arjunglucoside I; ARG), the kinetics of AChE inhibition is tested. The Michaelis–Menten constant (Km) for the hydrolysis of the acetylthiocholine iodide substrate was calculated to be 0.011 mM.

Myocardial infarction (MI) is a serious cardiovascular disease that can lead to death. Cardiac troponin I (cTnI) is a biomarker of MI in the circulation system. For detection cTnI protein, many method suffer the same problem, time-consuming. Main drawbacks are time consuming, have tedious operation, require an expensive reader for translating signals, and require non-accessible reagents. Our goal is to create a kit for cTnI protein testing, that the result can easily be read by color difference. The main breakthrough is, the resolution between different concentration can be told by eyes. The result will be future used to create a commercial, potable, convenient, daily-used rapid-test kit. In this study, a cTnI biosensor is proposed that can be read by the naked eye, performs diagnosis based on the pattern color, does not require a reader machine, is easy to operate, and is portable. Our work proposed a device that shortens the diagnosis time, has a quantitative analysis range of 0.32 –200 ng/mL in the human serum matrix, has a 0.32 ng/mL limit of detection (LOD), and shows many advantages comparing to traditional cTnI ELISA plate.

The use of anti-microbial drugs and coccidiostats in poultry farming is widespread, with a significant proportion of these drugs being excreted and released into the environment. The residues of such drugs in poultry litter (PL) can result in the development of antibiotic-resistant bacteria. The impact of different biotic treatments (aerobic, anaerobic, and stacking) on broiler litter (BL) before use as animal feed has not been studied extensively, nor have the differences between antimicrobial-dependent and independent broiler farms been investigated. This study aimed to determine the resistant bacteria in BL used as ruminant feed before and after litter treatment. The results showed that the most resistant bacteria before BL treatment were Enterococcus species. The study also found that the quantity of amoxicillin-resistant Enterococcus detected in samples from antimicrobial-dependent farms was significantly higher than in those from antimicrobial-independent farms. Additionally, 14% of bacteria were multi-resistant to tetracycline, sulfafurazole, and erythromycin in antimicrobial-independent farm litters, significantly lower than those measured in antimicrobial-dependent broiler farm litter. This study highlights the importance of better understanding, regulating, managing, and using animal waste appropriately to reduce the number of antibiotic-resistant bacteria and minimize the use of antimicrobials that carry high risks for animals, humans, and the environment

The epidemiology of invasive fungal infections (IFIs) is currently changing, driven by aggressive immunosuppressive therapy, leading to an expanded spectrum of patients at risk of IFIs. Aspergillosis is a leading cause of IFIs, which usually affects immunocompromised patients. There is a limited number of antifungal medications available for treating IFIs and their effectiveness is often hindered by rising resistance rates and practical limitations. Consequently, new antifungals, especially those with novel mechanisms of action, have become increasingly required. This study assessed the activity of four novel antifungal agents with different mechanisms of activity: manogepix, rezafungin, ibrexafungerp, and olorofim against 100 isolates of Aspergillus section Terrei, containing amphotericin B (AmB) wildtypes/non-wildtypes and azole-susceptible/-resistant strains, according to the European Committee on Antimicrobial Susceptibility Testing (EUCAST) method. In general, all tested agents showed potent and consistent activity against tested isolates, exhibiting a geometric mean (GM) and minimum effective concentration (MEC)/minimum inhibitory concentrations (MIC) range respectively as follows: manogepix (0.048 mg/L, 0.032-0.5 mg/L), rezafungin (0.020 mg/L, 0.016-0.5 mg/L), ibrexafungerp (0.071 mg/L, 0.032-2 mg/L), and olorofim (0.008 mg/L, 0.008-0.032 mg/L). In terms of MIC90/MEC90, olorofim had the lowest values (0.008 mg/L), followed by rezafungin (0.032 mg/L), manogepix (0.125 mg/L), and ibrexafungerp (0.25 mg/L). All antifungals tested demonstrated promising in vitro activity against Aspergillus section Terrei, including A. terreus and cryptic species that were azole-resistant and AmB non-wildtype.

As medical care aiming to maintain the quality of life for elderly patients is increases, implant treatment for elderly patients is increasing worldwide. Therefore, we aimed to investigate implant stability and the reliability of different measuring devices according to implant placement site and duration in patients aged over 65 years. The study evaluated 60 implants in 60 patients aged ≥ 65 years. The implant placement sites were divided into six evenly distributed sections (n=10) i.e., maxillary right- posterior, A; maxillary anterior, B; maxillary left-posterior, C; mandibular right-posterior, D; mandibular anterior, E; mandibular left-posterior, F. Participants visited the hospital seven times: preoperatively, 1V; implant surgery, 2V; stitch removal, 3V; 1-month follow-up, 4V; 2-months follow-up, 5V; before final-restoration delivery, 6V; and after final-restoration delivery, 7V. The implant stability was evaluated with the Osstell Mentor (ISQ), Periotest M (PTV), and Anycheck (IST). The mean values of ISQ, PTV, and IST were analyzed (α=.05). ISQ, PTV, and IST results of 5V and 6V were significantly higher than those of 2V (P<.05). The lowest ISQ results occurred in E location at 5V and 6V (P<.05). In all mandibular locations, IST results of 7V were significantly higher than those of 2V, 3V, 4V, and 5V (P<.05). ISQ results were negatively correlated with PTV and positively correlated with IST, and PTV was negatively correlated with IST. By considering various factors that affect implant stability, the appropriate implant load application time was determined. This could help increase the implant success rate in elderly patients. And as a diagnostic device for implant stability for evaluation of osseointegration in elderly patients, Anycheck was also able to prove its relative reliability compared to Osstell ISQ Mentor and Periotest M.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

The accurate of model attitude angel plays an important role on the aerodynamic test results in the wind tunnel test. The original method applies the spherical coordinate system transformation to obtain attitude angel calculation. The model attitude angel is obtained by coordinate transformation and spherical surface mapping applying the nominal attitude angel (the balance attitude angel in the wind tunnel coordinate system) indicated by the mechanism. First, the coordinate transformation of this method is not only complex but also difficult to establish the transformed relationship between the space coordinate systems especially after many steps of coordinate transformation, moreover it cannot realize the iterative calculation of the interference relationship between attitude angels; Second, during the calculate process to solve the problem the arc is approximately used to replace the straight line, the angel for the tangent value, and the inverse trigonometric function is applied. Therefore, in the calculation of attitude angel, the process is complex and inaccurate, which can be solved approximately when calculating small attack angel. However, with the advancing development of modern aerodynamic unsteady research, the aircraft tends to develop high or super large attack angel and unsteady research field. According to engineering practice and vector theory, the concept of vector angel coordinate system is proposed for the first time, and the vector angel coordinate system of attitude angel is established. With the iterative correction calculation and avoiding the problem of approximate and inverse trigonometric function solution, the model attitude calculation process is carried out in detail, which validates that the calculation accuracy and accuracy of model attitude angels are improved. Based on engineering and theoretical methods, a vector angel coordinate system is established for the first time, which gives the transformation and angel definition relations between different flight attitude coordinate systems, that can accurately calculate the attitude angel of the corresponding coordinate system and determine its direction, especially in the channel coupling calculation, the calculation of the attitude angel between the coordinate systems is only related to the angel, and has nothing to do with the change order s of the coordinate system, which simplifies the calculation process.

Coronavirus is a disease caused by a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) which emerged as a global pandemic in 2019 from Wuhan, China. Since its emergence, it has caused immense suffering to human life, 6.27 million lives have been lost, movement curtailed and social dynamics disrupted. The golden standard for getting samples for SARS-CoV-2 detection is through oral- nasopharyngeal swab, this method of sample collection is invasive and uncomfortable, thus stigmatized the general population, and thereby impeded the progress of controlling the spread through mass testing. Being a contact disease, mechanisms to encourage mass testing is key to reduce the spread. This study thus developed a complimentary sample type to test for SARS-CoV-2, the use of human feces. Fecal samples were collected from 100 asym-symptomatic individuals suspected to be infected with COVID-19, virus RNA was then extracted and profiled through Real Time Polymerase Chain Reaction (RT-qPCR). The antigen rapid diagnostic test revealed high positivity rate of 44%, but the real time polymerase chain reaction results on nasopharyngeal and fecal samples revealed a significant variation, high number of the patients tested positive with stool samples compared to the nasopharyngeal swabs, with 43 and 37%, respectively. SARS-CoV-2 virus was detected in both symptomatic and asymptomatic individuals; however, the symptomatic registered a higher positivity of 25% compared to 20% among the asymptomatic patients. Vaccination only lowered the risk of infection, fully and partially vaccinated lowered the infection level to 10% compared to 20% among the unvaccinated. Finally, gender parity in relation to COVID19 was evaluated, more females (56%) compared to males were recruited in this study, out of which (20; 43.4%) were positive, and 26 (56.6%) were negative based on fecal RT-qPCR outcomes. Based on the outcome of this study, rapid diagnostic test (Ag-RDT) however cheap and or fast does not provide accurate information, moreover, the virus does not stay longer within the Oro-nasopharyngeal region, thus the invalid or negative results, thus use of feces should be adopted as a confirmatory test to ascertain the COVID19 status of an individual.