The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Integrated disaster risk reduction in schools represents a key component of safety strategies within the educational sector of every country. In this study, a series of 850 face-to-face interviews (650 with students and 200 with teachers) were conducted throughout 2023 in 10 out of the total 18 municipalities in the Western Morava Basin of the Republic of Serbia. The paper proposes two central hypotheses regarding school-based disaster risk reduction. Firstly, it suggests that gender, age, parent's employment, academic achievement, living situation, paternal and maternal education levels, and engagement with social media collectively influence students' perspectives on this matter. Secondly, it posits that gender, age, marital status, parenthood, and educational background significantly impact teachers' viewpoints on school-based disaster risk reduction. Multivariate linear regression was used to explore predictors of students' and teachers' insights on school-based disaster risk reduction. Various statistical tests including Chi-square, t-tests, one-way ANOVA, and Pearson's correlation were employed to investigate the influence of demographic and socioeconomic factors on these insights. The results of multivariate regression analyses indicate that age, gender and marital emerge as the primary predictors across various facets of students' and teachers' insights on school-based disaster risk reduction (awareness of disasters, disaster education activities, attitudes on disaster risk reduction education, enhancement of disaster information accessibility, etc). The results of this study provide insight into the key factors influencing students' and teachers' perceptions of disaster risk reduction in schools. As such, they can serve as a basis for improving educational programs, developing policies and strategies, normative educational frameworks, teacher training, and further research in disaster education.

Tanning, crucial for leather production, relies heavily on chromium yet poses risks due to chromium's oxidative conversion, leading to significant wastewater and solid waste generation. Physico-chemical methods are typically used for heavy metal removal, but they have drawbacks, prompting interest in eco-friendly biological remediation techniques like biosorption, bioaccumulation, and biotransformation. The EU Directive (2018/850) mandates alternatives to landfilling or incineration for industrial textile waste management, highlighting the importance of environmentally conscious practices for leather products' end-of-life management, with com-posting being the most researched and viable option. This study aimed to isolate microorganisms from tannery wastewater and identify those responsible for different types of tanned leather biodegradation. Using a leather biodegradation assay (ISO 20136) with tannery and municipal wastewaters as inoculum, bacterial shifts during leather biodegradation were observed. Over 10,000 bacterial species were identified in all analyzed samples, with 8 bacterial strains isolated from tannery wastewater. Identification of bacterial genera like Acinetobacter, Brevundimo-nas, and Mycolicibacterium provides insights into potential microbial candidates for enhancing leather biodegradability, wastewater treatment, and heavy metal bioremediation in industrial applications.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

This study aims to enhance multimodal transportation systems by mitigating CO2 emissions and enhancing operational efficiency. It introduces a novel centralized cargo concentration approach tailored for regions facing geographical challenges. The method proposes for direct transportation of cargo from its loading origin to export ports, bypassing intermediate hubs. The mathematical model determines the most efficient means of transport for each route, factoring in variables like distance, volume, and cargo type. Research results indicate that, in scenarios with a high concentration of cargo, multiple hubs may not be necessary, which could streamline transportation and logistics operations. Modal preferences vary based on regional dynamics and cargo characteristics, with rail and sea transport emerging as preferable options under specific circumstances, surpassing the efficacy of road transport. The proposed model showcases reductions in both logistics costs and CO2 emissions compared to road-centric scenarios. It underscores the strategic integration of diverse transportation modes as pivotal for enhancing efficiency and sustainability. This study furnishes a framework adaptable to optimizing multimodal transportation systems in regions sharing similar geographical and logistical attributes.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

This paper introduces an innovative energy circuit that challenges conventional understandings of energy conservation, marking a significant departure from traditional frameworks. Seeking to enhance energy generation within existing paradigms, this innovation holds promise for addressing pressing global issues such as the energy crisis and environmental sustainability, while also stimulating scientific inquiry. In contrast to prevalent misconceptions rooted in philosophical and scientific constraints, this study refutes the notion of generating energy from nothing and questions the viability of perpetual motion machines as conceptual models. Instead, it proposes a novel circuit design derived from an unconventional electrical short circuit, which is shown to disrupt the established principles of energy conservation. This circuit offers a transformative approach with diverse applications, including self-recharging capabilities for electric vehicles, bolstering microgrid infrastructure, and facilitating the integration of renewable energy sources. Transcending conventional scientific boundaries, this paper prompts philosophical reflections on the evolving nature of scientific exploration. Ultimately, the energy circuit represents a pivotal step towards mitigating the global energy crisis by reducing reliance on finite resources and fostering sustainability. The paper concludes by illustrating the circuit's potential to revolutionize energy systems and contribute to a more resilient and sustainable future.

In this paper, a proof similar to the Pusey-Barrett-Rudolph (PBR) theorem is given to prove that time in quantum theory is not epistemic but has ontological reality. For this, we first discuss how time can be encoded as an intrinsic property of a quantum system. We prepare a quantum state containing time as an intrinsic property and show by a PBR-type proof that time cannot be an epistemic notion. In fact, the PBR theorem implies an ontic notion of time. Indeed, if the quantum state is a physical property, then quantum state reduction is a physical process involving information destruction. In this case, quantum probabilities are intrinsic probabilities without epistemic origin, and they generate a genuinely new sequence of events. This novelty introduced by quantum probabilities can be interpreted as time.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Ammonia can be considered a relevant compound in the future energy sector, playing a significant role as an energy carrier, storage, or carbon-free fuel. However, the production of this molecule has a high energy demand, and the use of natural gas, which is not free of controversy due to the accidental leakage into the atmosphere produced during extraction and the fact that it is a non-renewable source, contributes to increasing greenhouse gas emissions. Reducing the process’s energy demand and carbon footprint will be essential to making ammonia a clear alternative for a carbon-free economy. Given the vast experience in ammonia production and handling, this gas seems to be the logical step forward in the evolution of the energy sector. However, the current uncertainty in the global market requires cautiousness in decision-making. Several factors may impact economic growth and human welfare, thus needing a careful assessment before taking any transcendental decisions that could affect worldwide energy prices and raw material availability.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

Using multi-color flow cytometry analysis, we studied the immunophenotypical differences between leukemic blasts/LSCs from patients with AML/MDS and hematopoietic stem and progenitor cells (HSPCs) from patients in complete remission (CR) following their successful treatment. The panel of markers included CD34, CD38, CD45RA, CD123 as representatives for a hierarchical hematopoietic stem and progenitor cell (HSPC) classification as well as programmed death ligand 1 (PD-L1). Rather than restricting the evaluation on a 2- or 3-dimensional analysis, we applied a t-distributed stochastic neighbor embedding (t-SNE) approach to get a deeper insight and segregation between leukemic and normal HPSCs. For that purpose, we created a t-SNE map, which resulted in the visualization of 27 cell clusters based on their similarity concerning the composition and intensity of antigen expression. Two of these clusters were “leukemia-related” containing a great proportion of CD34⁺/CD38^- hematopoietic stem cells (HSCs) or CD34⁺ cells with a strong coexpression of CD45RA/CD123, respectively. CD34⁺ cells within the latter cluster were also highly positive for PD-L1 reflecting their immunosuppressive capacity. Beyond this proof of principle study, the inclusion of additional markers will be helpful to refine the differentiation between normal HSPCs and leukemic cells, particularly in the context of minimal disease detection and antigen-targeted therapeutic interventions. Furthermore, we suggest a protocol for the assignment of new cell ensembles in quantitative terms, via a numerical value, the Pearson coefficient, based on a similarity comparison of the t-SNE pattern with a reference.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude <6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

In the area of dental healthcare services, where patients and professionals deal with multiple auditory stimuli, this cross-sectional study reports on the intricate dynamics of sound preferences, noise obstacles, and the profound impact of music on anxiety reduction within dental office set-tings. The sample comprises of 134 dental patients, primarily females (56.7%), with varying age groups, education levels, and therapy durations in the university clinics of the department of Dentistry, National and Kapodistrian University of Athens and four private dental offices at the metropolitan area of Athens, Greece. Notably, 92.5% of the participants report no hearing loss, and 56.7% exhibit some level of noise sensitivity. The study reveals a moderate to good perceived health status (M=3.84, SD=0.95) among participants, with low perceived noise disturbance in university dental clinics. Preferences for instrumental music, foreign pop, and classical music are prominent during waiting times. Potential irritations include impersonal treatment (44%) and staff behavior (41.8%). Music player usage within the settings of the dental clinic involves radios (49.3%) and headphones (41.0%). Correlations and predictors indicate associations between health status, music preferences, and noise disturbances. More specifically, visiting the university dental clinics (β = .300, p = .005) as well as younger age (β = .300, p = .034) were significant predictors of better perceived health status. Clearer perception of external sounds while using the music player (β = .190, p = .039) was a significant predictor of better perceived health status, while poorer health was predicted by the preference of Greek folk songs (β = -.200, p = .030). Also, the use of smartphones for playing music was related to poorer health (β = -.370, p < .001). Following, younger age (β = -.270, p = .015), lower education (β = -.210, p = .035), higher noise sensitivity (β = .190, p = .027), as well as feelings of anxiety and nervousness due to ambient noise from people and machines (β = .510, p = .027) were significant predictors of noise disturbance from machines. Also, visiting private clinics (β = .240, p = .018), preferences of specific playlist (β = .310, p = .012), no music (β = .280, p = .016) and use of smartphones to play music (β = .230, p = .029) were significant predictors of noise disturbance from patients or staff. Finally, the preference of listening to a specific playlist was related to better health status (r = .190, p < .05). Findings aim to optimize eco-soundscapes in dental offices, con-tributing to enhanced patient well-being. The research underscores the potential of music inter-ventions to alleviate dental anxiety and improve the overall dental experience and quality care.

This study proposed to use wearable EEG to study the impact of vipassana mindfulness practice on beginner's physiological and neurological responses. Mindfulness meditation has been shown to have numerous benefits, including stress reduction, improved attention and cognitive function, and enhanced emotional regulation. The roots of mindfulness meditation in Buddhism emphasize cultivating present-moment awareness and insight. However, the neural mechanisms together with physiological mechanism and their interaction underlying these benefits remain poorly understood. Method: One middle age man (50 years old) participated in this longitudinal study using wearable EEG to investigate the neurophysiological change during a one-month consecutive vipassana mindfulness practice. Both EEG and heart rate responses were recorded each time, before (5 minutes), during (20 minutes), and after (5 minutes) meditation sessions. The EEG and HR data were analyzed by Matlab and EEGlab to examine changes in brainwave activity and heart rate. Results: alpha peak frequency (APF) is significantly lower after mindfulness meditation, as shown by comparison of APF before mindfulness (pre-5) and during mindfulness practice (med-20), and comparison between APF of pre-5 and after mindfulness practice (post-5). The same is with the beta peak power. While for theta peak frequency, it is significant lower during mindfulness meditation (med-20), when comparing to either pre-5 or post-5. See figure 1a. However, peak power index is not so sensitive, and it is more obvious in theta wave band. That is, the theta power peak is significantly lower after meditation, as can be observed in comparison between pre-5 and med-20, also between pre-5 and med-20. See figure 1b. STATE Heart-mean (bpm) Heart-std(bmp) pre-5 69.88 3.88 med-20 68.36 2.81 post-5 69.55 4.13 t-value test (pre-med) 0.0694 0.0003 t-value test (pre-post) 0.7934 0.3656 t-value test (post-med) 0.3193 0.0001 Table 1. The difference of Heart rate (mean and SD) in before (pre-5), during (med-20) and after (post-5)mindfulness meditation. We find significant change in standard deviation (SD) of heart rate between meditation and non-meditation mental states, as shown in table 1. The study provides insights into the underlying neurophysiological mechanisms of mindfulness meditation using wearable EEG devices. It demonstrates that in term of EEG measurement, spectrum frequency can be more sensitive than spectrum power; also heart rate variability as measured by SD is more sensitive to mean of HR. The proposed study contributes to the literature by using wearable EEG devices to collect data in a more accessible and convenient manner.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

Based on a very fast numerical procedure for the determination of the subsurface stress field beneath frictional contacts of axisymmetric elastic bodies under arbitrary 2D oblique loading, the contact mechanical influences of loading parameters and contact profile geometry on the Smith-Watson-Topper (SWT) fatigue crack initiation parameter in elastic fretting contacts with superimposed normal and tangential oscillations are studied in detail. The efficiency of the stress calculation allows for a comprehensive physical analysis of the multi-dimensional parameter space of influencing variables. It is found that a superimposed normal oscillation of the contact can significantly increase or decrease the SWT parameter, depending on the initial phase difference and frequency ratio between the normal and tangential oscillation. Written in proper non-dimensional variables, the rounded flat punch always exhibits smaller values of the SWT parameter, compared to a full paraboloid with the same curvature, while the truncated paraboloid exhibits larger values. A small superimposed profile waviness also significantly increased or decreased the SWT parameter, depending on the amplitude and wave length of the waviness. While both the load protocol and the profile geometry can significantly alter the SWT parameter, the coupling between both influencing factors is weak.

The introduction of ChatGPT in academia has raised significant concerns, particularly regarding issues like plagiarism and the ethical use of generative text for academic purposes. Existing literature has predominantly focused on ChatGPT adoption, leaving a notable gap in addressing the strategies users employ to mitigate these emerging challenges. To bridge this gap, this research utilizes the Uncertainty Reduction Theory (URT) to formulate user strategies for reducing uncertainty. These strategies include both interactive and passive approaches. Concurrently, the study identifies key sources of uncertainty, which include concerns related to transparency, information accuracy, and privacy. Additionally, it introduces the concepts of seeking clarification and consulting peer feedback as mediating roles to facilitate reduced uncertainty. We tested these hypotheses with a sample of Indonesian users (N = 566) using structural equation modeling via Smart-PLS 4.0 software. The results confirm that interactive Uncertainty Reduction Strategies (URS) are more effective in reducing uncertainty when using ChatGPT compared to passive URS. Transparency concerns, information accuracy, and privacy concerns are identified as factors that increase the level of uncertainty. In contrast, consulting peer feedback is the most effective strategy for reducing uncertainty compared to seeking clarification at the individual-system level. Insights from the mediating effects confirm that consulting peer feedback significantly mediates uncertainty sources to reduce uncertainty. The study discusses various strategies for the ethical use of ChatGPT by users in the educational context and contributes significantly to theoretical development.

The use of hyperthermia is one of the effective methods of treating cancer. In this case, the problem arises of constructing and predicting the distribution of the thermal field inside tissues depending on their type. This paper discusses the use of linear and polynomial regression methods, as well as regression algorithms based on decision tree, random forest and K nearest neighbors methods to recover missing temperature values. The influence of the size of the training sample when performing regression on the quality of the reconstructed values is investigated. Experimental recommendations on sample size are given for the selected decision tree and random forest methods. The possibility of a significant (10 times or more) reduction in the initial sample size, without leading to a decrease in the R² metric by more than 0.05 for various tissues, has been shown.

Two ferrocene derivatives, namely, 1,2-(tetramethylene)-ferrocene and 1,2,1’,2’-bis(tetramethylene)-ferrocene, were synthesized in a four-step reaction sequence starting from ferrocene. Friedel-Craft acylation of ferrocene with succinic anhydride gave mono- or bis(3-carboxypropinoyl)ferrocene depending on the stoichiometry of succinic anhydride. The reduction of the keto groups to methylene, followed by ring-closing using trifluoroacetic anhydride gave 1,2-(α-ketotetramethylene)-ferrocene or 1,2,1’,2’-bis(α-ketotetramethylene)ferrocene. The diastereomeric mixture of the latter diketones was separated by column chromatography, characterized by single-crystal X-ray analysis, and assigned their stereochemistry. Reduction of the keto groups to methylene under Clemmensen conditions gave homoannular mono- or bis(tetramethylene) ferrocene derivatives. The molecular structure of 1,2-(tetramethylene)-ferrocene revealed that the ipso carbon atoms of the cyclopentadienyl group are 0.023(3) Å farther away from Fe(II) compared to the remaining three carbon atoms. Both complexes exhibit lower half-wave oxidation potentials than ferrocene, possibly due to the electron-releasing effects of the tetramethylene bridges.

Early-onset colorectal cancer (EOCRC) is defined as a diagnosis of colorectal cancer (CRC) in individuals younger than 50 years of age. While overall CRC rates in the United States (US) decreased between 2001 and 2018, EOCRC rates have increased. This research project aims to evaluate the feasibility and acceptability of Time-Restricted Eating (TRE), Mindfulness, or TRE combined with Mindfulness among young to middle-aged adults at risk of EOCRC. Forty-eight participants will be randomly assigned to one of four groups: TRE, Mindfulness, TRE &amp; Mindfulness, or Control. Data on feasibility, adherence, and acceptability will be collected. Measures assessed at baseline and post-intervention will include body weight, body composition, dietary intake, physical activity, sleep behavior, circulating biomarkers, hair cortisol, and gut microbiome. Effects of the intervention on the following will be examined: 1) acceptability and feasibility; 2) body weight, body composition, and adherence to TRE; 3) circulating metabolic, inflammation, and oxidative stress biomarkers; 4) intestinal inflammation; and 5) the gut microbiome. TRE combined with Mindfulness holds promise for stress reduction and weight management among individuals at risk of EOCRC. The results of this pilot study will inform the design and development of larger trials aimed at preventing risk factors associated with EOCRC.

The new energy structure needs to balance energy security and dual carbon goals, which has brought major challenges to coal-fired power plants, the pollution reduction and carbon emissions reduction of coal-fired power plants will be a key task in the future. This article proposes an optimization operation of electrostatic precipitators(ESP), based on the working mechanism and historical data of ESP, voltage-current characteristic model and outlet dust concentration prediction model are constructed by deep learning algorithm, Particle Swarm Optimization(PSO) is used to achieve the optimal energy consumption while ensuring stable outlet dust concentration. By training with historical data collected on site, accurate prediction of secondary current and outlet dust concentration of ESP has been achieved, the Mean Absolute Percentage Error(MAPE) of secondary current is less than 1.5%, and the MAPE of outlet dust concentration of ESP on the test set is less than 5.2%. Finally, the optimization experiment is carried out in a 330MW coal-fired power plants, the results showed that the fluctuation of the outlet dust concentration is more stable, and the energy saving is about 43% after optimization, according to the annual operation of 300 days, the annual average carbon reduction is approximately 2621.34 tons. This method is effective and can be applied widely.

With the rapid advancements in remote sensing technology, the spectral information from hyperspectral remote sensing images has become increasingly rich, facilitating detailed spectral analysis of the Earth's surface objects. However, this abundance of spectral data poses significant challenges in data processing, such as the curse of dimensionality leading to the “Hughes” phenomenon, "strong correlation" due to high resolution, and "non-linear characteristics" caused by varied surface reflectance rates. Therefore, dimensionality reduction of hyperspectral data has become a crucial task. This paper, grounded in manifold theory and manifold learning techniques, and considering the non-linear structures and features in hyperspectral remote sensing data, elucidates the principles and processes of dimensionality reduction in hyperspectral remote sensing images using manifold learning, with a formalized expression of the process. This article introduces spectral information divergence (SID) into the nearest neighbor graph computation of manifold learning algorithms. The principles and computational processes of nearest neighbor graph algorithms based on Euclidean distance (ED), spectral angle mapping (SAM), and SID are studied, and a comparative analysis of the dimensionality reduction effects under these three metrics in hyperspectral data is conducted. Experiments on feature extraction under different metrics were performed using the publicly available Indian Pines hyperspectral dataset. The intrinsic features obtained post-dimensionality reduction were used as inputs for classification algorithms in ground objects classification experiments, with algorithm runtime, overall accuracy, and Kappa coefficient as evaluation metrics for dimensionality reduction quality. The results demonstrate that nearest neighbor graph computation based on SAM and SID outperforms traditional ED methods; SAM-based computation has the lowest time complexity, while SID-based manifold learning yields the highest accuracy in ground objects classification. Thus, manifold learning based on SAM and SID metrics proves to be an effective method for feature extraction in hyperspectral remote sensing data, underscoring the potential of manifold learning techniques in the dimensionality reduction of hyperspectral remote sensing images.

The current economic development paradigm, which is based on steadily rising resource consumption and pollution emissions, is no longer viable in a world with limited resources and ecological capacity. The "green economy" idea has presented this context with a chance to alter how society handles the interplay between the environmental and economic spheres. The related concept of "green nanotechnology" aims to use nano-innovations within the fields of materials science and engineering to generate products and processes that are economically and ecologically sustainable, enabling society to establish and preserve a green economy. Many different economic sectors are anticipated to be impacted by these applications, including those related to corrosion inhibitor nano fertilizers, nano remediation, biodegradation, heavy metal detection, biofuel, insecticides & pesticides, and catalytic CO2 reduction. These innovations might make it possible to use non-traditional water sources safely and to create construction materials that are enabled by nanotechnology, improving living and ecological conditions. Therefore, our aim is to highlight how nanotechnology is being used in the green economy and to present promises for nano applications in this domain. Additionally, we want to critically examine the practical difficulties these applications raise, especially in consideration of any possible implications for the health and safety of those employed within this innovative sector. In the end, it emphasizes how critical it is to attain a really sustainable advancement in nanotechnology.

One of the challenges of deploying Wireless Sensor Networks (WSN) at large scale is to operate for prolonged periods of time relying on the limited amounts of energy stored in its nodes. Generally, data communication is the main factor of draining energy. Consequently, reducing the amount of transmitted data by the nodes is of great interest. At the same time, reducing data to be transmitted should not decrease the quality of the deduced information. Solving this problematic is what we call in this article "Ensuring the Quality of Information Service (QoIS)". This document provides a state-of-the-art for the QoIS regarding WSNs. At first, we give a quick overview of the Internet of Things (IoT) paradigm and the WSN technologies in order to understand how data is gathered and used in these networks. Also, we introduce a novel concept: QoIS, in contrast with classic QoS. Then, it is expected a summary of criteria that asses the QoIS in WSNs plus some techniques to improve it. In this article, we will focus on data management techniques. These techniques can improve raw data, information and/or knowledge quality in energy-constrained WSNs. Finally, we give some conclusions and a glimpse about our future work.

The efficiency and performance of Proton Exchange Membrane Fuel Cells (PEMFCs) are primarily influenced by ORR electrocatalysts. In recent years, atomically dispersed met-al-nitrogen-carbon (M-N-C) catalysts have gained significant attention due to their high active center density, high atomic utilization, and high activity. These catalysts are now considered the preferred alternative to traditional noble metal electrocatalysts. The unique properties of M-N-C catalysts are anticipated to enhance the energy conversion efficiency and lower the manufac-turing cost of the entire system, thereby facilitating the commercialization and widespread ap-plication of fuel cell technology. This article initially delves into the origin of performance and degradation mechanisms of Fe-N-C catalysts from both experimental and theoretical perspectives. Building on this foundation, the focus shifts to strategies aimed at enhancing the activity and durability of atomically dispersed Fe-N-C catalysts. These strategies encompass the use of bi-metallic atoms, atomic clusters, heteroatoms (B, S, and P), and morphology regulation to optimize catalytic active sites. The article concludes by detailing the current challenges and future pro-spects of atomically dispersed Fe-N-C catalysts.

Precision farming is transforming how antibiotics get used on farms. It fights the overuse that creates superbugs and harms nature. Farmers now have high-tech tools to use antibiotics ultra-precisely. Drones, AI, and advanced watering equipment help them pinpoint only sick plants and animals needing treatment. This shields crops while avoiding environmental damage. More careful antibiotic use makes livestock healthier and boosts harvests too. And it prevents resistant germs, where antibiotics stop working altogether. The approach helps farms in multiple ways, using fewer resources for even better results. There are some growing pains, like high costs for small farms. And questions around data privacy also cause concern. But overcoming these hurdles could help precision farming spread far and wide. This technology promises safer, greener, and more productive agriculture. Targeted use of antibiotics protects both crops and people from drug-proof germs. And nature benefits when less medicine spreads into soil and water. The future looks bright for farming with precision.

Environmental pollution is becoming ubiquitous; it has a negative impact on the ecosystem diversity and worsens the quality of human life. This review discusses the possibility of applying the Plant Microbial Fuel Cells (PMFC) technology for concurrent processes of electricity generation, purification of water and soil ecosystems from organic pollutants, in particular, from synthetic surfactants and heavy metals. The review describes the PMFC functioning mechanisms and highlights the issues of the PMFC environmental application. Generally, this work summarizes different approaches to the PMFC development and to the potential usage of such hybrid bioelectrochemical systems for the environmental protection.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

Integrating photovoltaic (PV) systems plays a pivotal role in the global shift toward renewable energy, offering significant environmental benefits. In many instances, utility companies pay for both energy and peak demand. PV systems can effectively reduce energy consumption during their operational periods, while, their contribution during peak hours, particularly in the early morning and late evening, is often limited. To address this issue, battery storage systems are utilized for storing energy during off-peak hours and releasing it during peak times. However, finding the optimal size of PV-battery systems remains a challenge. This study proposes a novel statistical model to optimize PV-battery system sizing for enhanced peak demand reduction. The model aims to flatten 95% of peak demand days up to a certain demand threshold, ensuring consistent energy supply and financial benefit for utility companies. A straightforward and effective search methodology is employed to determine the optimal system sizes. Additionally, the model effectiveness is rigorously tested through a modified Monte Carlo simulation coupled with time series clustering to generate various scenarios to assess performance under different conditions. The results indicate that the optimal PV-battery system successfully flattens 95% of daily peak demand up to 2000 kW, yielding a financial benefit of $812,648 over 20 years.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

The use of artificial intelligence technologies may help companies obtain the optimal use of resources and accomplish more activities with an increase in productivity by 40%. With access to real-time data and the ability to learn from patterns and behaviors, AI can perform these routine tasks more efficiently. Ambient intelligence, Ami, is one of the applications of artificial intelligence, which is called artificial environmental intelligence, which is a concept that focuses on using technology to create an environment that is intelligent and responsive to the needs of its users. This technology has the potential to revolutionize disaster response and management, which in turn facilitates access to necessary information and resources. necessary vitality in the event of a crisis. It may use ambient intelligence to create a network of sensors that can detect and respond to changes in the environment. So that this network can be used to monitor the environment for potential disasters, such as floods, fires and earthquakes. Sensors can also be used to detect changes in temperature, humidity, and other environmental factors that may indicate a potential disaster. This information can then be used to alert emergency responders and provide them with the information needed to respond quickly and effectively. Ambient intelligence can also be used to create a comprehensive database of resources and information that can be accessed in times of crisis. This database may include information about the location of shelters, medical facilities, and other resources that can be used to assist those affected by a disaster. It may also provide information about the condition of roads, bridges, and other infrastructure that may be affected by a disaster. This information can be used to inform response and management decisions, helping to ensure that resources are used in the most efficient way possible. Ambient intelligence can be used to create a communication platform between emergency responders and those affected by a disaster. This platform can also be used to provide updates on the emergency situation, in addition to providing information about available resources to those affected. This can help ensure that those affected by a disaster can access the resources they need in a timely manner.

The aim of this study was to assess and contrast the effects on the vertical marginal fit of full contour CAD/CAM generated monolithic zirconia crowns pre- and post-cementation of employing chamfer finishing line designs with various occlusal reduction schemes (planar and flat) and cements. Material and Method: Forty sound human maxillary first premolars were selected for this study. Samples will be divided into two main groups of twenty samples in each group according to the occlusal reduction scheme: Group A: chamfer finishing line design with planar occlusal reduction scheme. Group B: chamfer finishing line design with flat occlusal reduction scheme. Each main group will be subsequently separated into two smaller groups based on the kind of cement that was utilized (n=10) Subgroup A1: crowns will be cemented by using resin-modified Glass Ionomer cement (Fuji Plus). Subgroup A2: crowns will be cemented using a Universal adhesive system (Duo Estecem II). Subgroup B1: crowns will be cemented by using Fuji Plus. Subgroup B2: crowns will be cemented using a Duo Estecem II. Result: Marginal gaps were measured at 4 indentations, using a Dino light-stereomicroscope (230X). Paired T-tests and student t-tests analyzed the data. Prior to cementation, subgroup A1 scored the lowest mean of vertical marginal gap values (80.284±23.021), while subgroup B2 scored the highest mean (118.597±9.956); following cementation, subgroup A1 scored the lowest mean of vertical marginal gap values (95.45±17.598), and subgroup B2 scored the highest mean of vertical marginal gap values (134.806 ±8.114). Chamfer finishing line design with a planar occlusal reduction scheme could be a preferable occlusal reduction scheme.

In this work, Density Functional Theory (DFT) calculations were employed to study the photocatalytic CO2 to CO reduction by a series of Pt(II) square planar complexes with general formula [Pt(5-R-dpb)Cl] (dpb = 1,3-di(2-pyridyl)benzene anion, R = H, N,N-dimethylaniline,T thiophene, diazaborinine). The CO2 to CO conversion process is thought to proceed via two main steps, namely the photocatalytic/reduction step and the main catalytic step. The simulated absorption spectra exhibit strong bands in the 200 – 400 nm UV-Vis region. The calculated excited state reduction potentials are in the range 0.32 — -0.36 V revealing that the reductive quenching of the T1 state of the complexes could be modulated with suitable changes of the N^C^N pincer ligands. The CO2 fixation and activation by the ‘real’ three coordinated Pt(II) catalyst/intermediate is predicted to be favorable with Pt-CO2 bond dissociation energies, D0 in the range -36.9—-10.3 kcal/mol. The nature of the Pt-CO2 bond is complex with covalent, hyperconjugative and H-bonding interactions prevailing the repulsive electrostatic interactions. The main catalytic cycle is estimated to be a favorable exergonic process.

The urgency for a shift towards cleaner and more efficient energy alternatives for power generation is underscored by the escalating demand for energy and the detrimental environmental impacts of conventional fossil fuels. In the case of automotive power, electric vehicles are being adopted in many applications, however, challenges remain such as extended charging periods and limited ranges between charges. Therefore, this research study conducts a techno-economic analysis of renewable energy technologies (including solar modules, wind turbines and piezoelectric materials) to augment the efficiency and sustainability of electric buses. The study examines the scope for these technologies to be adopted on double-decker electric buses in London in the United Kingdom. The solar modules are placed on the rooftop and sides of the bus generating 15.9 kWh/day and the wind turbine in the front bumper of the bus generates 8.3 kWh/day. However, the piezoelectric material generated only 22.6 Wh/day, rendering it an impractical inclusion in further analysis. Therefore, both the solar modules and wind turbines combined generate 24.2 kWh/day, which can increase the driving range by 16.3 km per day and this results in savings of 19.36 minutes for charging at the stations. Investing in such projects would have a positive return as the internal rate of return (IRR) and net present value (NPV) are 2.8% and £11,175 respectively. The annual revenue would be £6,712, and the greenhouse gas (GHG) reduction would be two metric tons annually. Electricity exported to the grid, the electricity export rate, and the initial investment are identified as key factors influencing power outage in a sensitivity analysis. In conclusion, this numerical modelling study paves the way for experimental validation towards implementation of renewable energy technologies on electric bus fleets.

The phenomenon of missing data can be seen everywhere in reality. Most typical attribute reduction models are only suitable for complete systems. But for incomplete systems, we can’t obtain the effective reduction rules. Even if there are a few reduction approaches, the classification accuracy of their reduction sets still needs to be improved. In order to overcome these shortcomings, this paper firstly defines the similarities of intra-cluster objects and inter-cluster objects based on the tolerance principle and the mechanism of knowledge granularity. Secondly, attributes are selected on the principle that the similarity of inter-cluster objects is small and the similarity of intra-cluster objects is large, and then the knowledge granularity attribute model is proposed under the background of clustering; Then, the IKAR algorithm program is designed. Finally, a series of comparative experiments about reduction size, running time and classification accuracy are conducted with twelve UCI data sets to evaluate the performance of IKAR algorithms, then the stability of Friedman test and Bonferroni-Dunn test are conducted. The experimental results indicate that the proposed algorithms are efficient and feasible.

Abstract Big datasets are becoming increasingly common and can be challenging to understand and apply in public health. One method for lowering the dimensionality of these datasets and improving interpretability while minimizing information loss is data reduction using principal component analysis (PCA). It achieves this by successively maximizing variance through the creation of new, uncorrelated variables. PCA is an adaptive data analysis technique because it simplifies the process of finding new variables, or principal components, by solving an eigenvalue or eigenvector problem. These new variables are determined by the dataset being used, rather than by the analyst starting from scratch. It is also adaptable in another way because varieties of the method have been designed to adjust to various data structures and types. However, there are serious problems in the theoretical understanding and practical application of PCA in public health researchers, whereas its application is becoming popular in developing countries. Therefore, this article, which concentrated on using PCA to reduce data, began by outlining the fundamental concepts of PCA and going over what it can and cannot do, as well as when and how to use it. We also discussed the fundamental assumptions, benefits, and drawbacks of PCA. Furthermore, this article demonstrated and resolved PCA practical application problems in public health that most scholars are unaware of, such as variable preparation, variable inclusion and exclusion criteria for PCA, iteration steps, wealth index analysis, interpretation, and ranking.

This article systematically reviews the research achievements on the MnOx/TiO2 catalyst doped with transition metals or rare earth metals for the catalytic selective catalytic reduction of NH3 (SCR-NH3) reaction. The Methodi Ordinatio systematic literature analysis method was employed to rank relevant articles based on journal impact factors, publication years, and citation counts. The ranking data shows that the undoped MnOx/TiO2 catalysts exhibit a catalytic efficiency of up to approximately 90% for NOx reduction, while the doped MnOx/TiO2 catalysts with transition metals or rare earth metals can achieve a maximum reduction efficiency of 100%. Among all the doped metals, the catalyst doped with nickel demonstrates the best NOx reduction performance. The comprehensive literature research concludes that MnOx/TiO2-based SCR catalysts, especially those doped with transition metals or rare earth metals, have significant catalytic efficiency and development potential in reducing NOx emissions in SCR reactions.

The reduction of Ce cations in CeO2 can be enhanced by its partial substitution by Fe cations. The enhanced reduction of Ce cations results in a considerable increase in the reaction rates for thermal water splitting reaction when compared to CeO2 alone. This mixed oxide has a smaller crystallite size when compared to CeO2 in addition to a smaller lattice size. In this work, two Fe-substituted Ce oxides are studied (Ce0.95Fe0.05O2 and Ce0.75Fe0.25O2) by core and valence level spectroscopy in their as-prepared and Ar-ions sputtered states. Ar-ions sputtering substantially increases Ce4f lines at about 1.5 eV below the Fermi level. In addition, it is found that the XPS Ce5p/O2s ratio is sensitive to the degree of reduction, most likely due to a higher charge transfer from the oxygen to Ce ions upon reduction. Quantitatively it is also found that XPS Ce3d of the fraction of Ce3+ (uo, u’ and vo, v’) formed upon Ar-ions sputtering and the ratio Ce5p/O2s lines are higher for reduced Ce0.95Fe0.05O2 than for reduced Ce0.75Fe0.25O2. XPS Fe2p showed however no preferential increase for Fe3+ reduction to Fe0 with increasing time for both oxides. Since water splitting was higher on Ce0.95Fe0.05O2 when compared to Ce0.75Fe0.25O2, it is inferred that the reaction centers for the thermal water splitting to hydrogen are the reduced Ce cations and not the reduced Fe cations. These reduced Ce cations can be tracked by their XPS Ce5p/O2s ratio in addition to the common XPS Ce3d lines.

The past is an important lesson for facing the future with greater awareness. In this context, school plays a key role to spread knowledge on natural phenomena and to promote behavior change. Together with researchers, teachers can be strong allies to build more resilient future citizens. The Istituto Nazionale di Geofisica e Vulcanologia (INGV) school training activities provide tools to get ready for the next earthquake and/or tsunamis. About 5000 students from both Middle schools (ISCED 2) and High schools (ISCED 3) were involved in active learning activities based on a flipped-up approach during special online scientific events in the Pandemic. Online lab activities were conducted respectively during the European Researchers’ Night (“Earthquakes: history teaches us the future: researchers for a day with experimentation in didactics for ESL”) and during the World Water Day 2021 and the World Earth Day 2021 (“Tsunamis: history teaches us the future researchers for a day with experimentation in didactics for ESL”). These two Episodes of Situated Learning (ELS) experiences triggered students’ interest, favoring remote learning, developing life skills, focusing on historical seismic studies of both past earthquakes and tsunamis.

Due to the ever increasing global warming, the scientific community is concerned with finding immediate solutions to reduce or utilize carbon dioxide (CO2) and convert it in useful compounds. In this context, the reductive process of CO2 methanation is well investigated and attractive due to its simplicity. However, it requires the development of highly active catalysts. In this mini-review, the focus is on biochar-immobilized nanocatalysts for CO2 methanation. We summarize the recent literature on the topic, reporting strategies for the design of biochar with immobilized nanocatalysts and their performances in CO2 methanation. We review the thermochemical transformation of biomass into biochar and its decoration with CO2 methanation catalysts. We also tackle direct methods of obtaining biochar-nanocatalysts, in one pot, from nanocatalyst precursor-impregnated biomass. We review the effect of the initial biomass nature, as well as the conditions that permit to tune the perfomances of the composite catalysts. Finally, we discuss the CO2 methanation performances and how they could be improved keeping in mind low operation cost and particularly sustainability.

Precision agriculture including camera-guided row detection and hydraulic steering are often used as an alternative because crop damage can be decreased and driving speed can be increased comparable to herbicide applications.The effects of different approaches as uncontrolled (UC), mechanical weed control (MWC), herbicide weed control (HWC) and mechanical + herbicide control (MWC+HWC) on weed density and yield of sugar beet were tested and evaluated in two trials (2021 and 2022) in South Transylvania at the tested intervals BBCH 19 and 31. Weed control efficacy (WCE) depends on the emergence of the weeds and a good timing of weed controls in all the trials and methods, though the highest yield of sugar beet roots was recorded in the treatment MWC+HWC, with an increase up to 12-15% (56.48 t ha-1) yield from HWC (50.22 t ha-1) and a yield increase of more than 35- 40% than MWC (42.34 t ha-1). Our trials show that is possible to increase yield and have less chemical applications with the introduction of the new precision technologies in agriculture included here the sensor-guided mechanical controls.

Computed tomography (CT) is a widely employed imaging modality with diverse clinical applications in pediatric and adult populations, offering numerous advantages. Despite several alternatives to imaging modalities with ionising radiation, CT scans have demonstrated persistent global popularity, contributing to a substantial amount of effective radiation doses for patients. This exposure results in hazards, including stochastic effects that amplify the radiation-induced cancer risk proportionally to the radiation dose received. CT-related radiation comprises a substantial portion of cumulative effective doses within diagnostic radiology, specifically impacting younger patient cohorts undergoing repeated investigations for chronic diseases over time. Scientific literature over recent decades has explored various methods to mitigate radiation doses during medical imaging. One notable strategy involves implementing low-dose and ultralow-dose CT protocols, maintaining diagnostic efficacy in acute and non-acute medical and surgical conditions. Utilising innovative image reconstruction algorithms, such as iterative reconstruction and emerging deep-learning algorithms based on artificial intelligence, plays a pivotal role in achieving an approximately 80% reduction in patient radiation compared to standard doses. This review article discusses the significance of low-dose protocols across a spectrum of acute and chronic medical conditions affecting different body systems.

Electromagnetic cloaking approach is employed with the intention to curb the destructive effects of mutual interference for rectangular and circularly shaped patch antennas situated in a tight spacing (sub-wavelength separation is employed). Primarily, we show that by coating the top surface of each patch with an appropriately designed metasurface, it is possible to considerably reduce the mutual coupling between the said antennas. We also demonstrate that, despite the close proximity of these patches, the individual radiation characteristic of each antenna is reinstated to emulate their performance in an isolated scenario. Furthermore, the cloak construct is extended to a tightly spaced, interleaved linear patch antenna array configuration and it is shown that the coated metasurfaces successfully enhance the performance of each array in terms of their matching characteristics, total efficiencies as well as their far-field realized gain patterns for a broad range of beam-scan angles. The decoupling and cloaking action of these metasurfaces are demonstrated by various full-wave numerical simulation results. We believe that the simple planar structure of our metasurface design (according to simulation models) makes it feasible for fabrication and the fact that it is used to accomplish cloaking of an electrically large antenna surface, makes it unique in itself.

A fundamentally new synthetic approach to the synthesis of 2-aminopurine has been developed. It consists in the combination of creation of condensed polyazotic heterocyclic tetrazolopyrimidine structure, it’s transformation into triaminopyrimidine and subsequent cyclization into 2-aminopurine. The structure of the obtained compounds was established based on spectral characteristics and intermediate 5 directly by X-ray diffraction analysis.

This paper aims to contribute to refining the e-values for testing precise hypotheses, especially when dealing with nuisance parameters, leveraging the effectiveness of asymptotic expansions of the posterior. The proposed approach offers the advantage of bypassing the need for elicitation of priors and reference functions for the nuisance parameters and the multidimensional integration step. For this purpose, starting from a Laplace approximation, a posterior distribution for the parameter of interest only is considered and then a suitable objective matching prior is introduced, ensuring that the posterior mode aligns with an equivariant frequentist estimator. Consequently, both Highest Probability Density credible sets and the e-value remain invariant. Some targeted and challenging examples are discussed.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

Breast cancer is the most prevalent malignancy among women globally. Early diagnosis and treatment improvements are leading to a growing population of survivors. This has increased the risk of developing contralateral breast cancer (CBC), a distinct occurrence in the opposite breast of a previously diagnosed patient. The treatment options for breast cancer are often mas-tectomy or lumpectomy. Patients with lumpectomy frequently undergo a contralateral reduc-tion procedure to achieve more symmetry after the primary breast cancer surgery. The reduc-tion specimen is usually routinely examined by pathology to check for malignancies. The exci-sion in pieces and the absence of specific markers or ink make an examination of tumor size and margin status more challenging, impacting treatment decisions. A new protocol introduced in July 2022 seeks to improve diagnostic precision and treatment planning by excision in toto, marking, and inking excised reduction tissue to examine and treat potential CBC more effectively.

This paper presents a model for archival and retrieval of the videos of natural flowers. To design an efficient video retrieval system the stages namely, keyframe selection, feature extraction, feature dimensionality reduction and indexing are essential for fast browsing and accessing of videos. Three different keyframe selection approaches are proposed using clustering algorithms after segmenting flower regions from its background. Deep Convolutional Neural Network is used as a feature extractor. After keyframe selection, a video is represented with a set of keyframes. To reduce the feature dimension of a video, two feature selection methods are utilized. For an efficient archival and fast retrieval of flower videos an indexing method called KD-tree is recommended. For a given query video, similar videos are retrieved both in relative and absolute search modalities. An extensive experimentation conducted on a relatively large flower video dataset. The data set consists of 7788 videos of 30 different species of flowers. The videos are captured with three different devices in different resolutions. The comparative study reveals proposed keyframe selection approaches gives better results. It has also been observed that the videos retrieved in absolute approach with features selected from Binormal separation metric and indexing gives good results.

Crop digital twin is redefining traditional farming practices, offering unprecedented opportunities for real-time monitoring, predictive and simulation analysis, and optimization. This research embarks on an exploration of the synergy between precision agriculture, crop modeling, and regression algorithms to create a digital twin for augmenting farmers the concentration and composition prediction-based crop nutrient recovery. This captures the holistic representation of crop characteristics, considering the intricate relationships between environmental factors, nutrient concentrations, and crop compositions. However, the complexity arising from diverse soil and environmental conditions makes nutrient content analysis expensive and time-consuming. This paper presents the result of a predictive digital twin case study that employs six regression algorithms namely Elastic Net, Polynomial, Stepwise, Ridge, Lasso, and Linear Regression to predict rice nutrient content efficiently, particularly considering the coexistence and composition of multiple nutrients. Our research findings highlight the superiority of the Polynomial Regression model in predicting nutrient content, with a specific focus on accurate nitrogen percentage prediction. This insight can be used for nutrient recovery intervention by knowing the precise amount of nutrient to be added into the crop medium. The adoption of the Polynomial Regression model offers a valuable tool for nutrient management practices in the crop digital twin, potentially resulting in higher-quality rice production and a reduced environmental impact. The proposed method can be replicable in other low-resourced crop digital twin system.

The International Maritime Organization (IMO) is enforcing increasingly stringent regulations on ship carbon emissions, The International Maritime Organization (IMO) has been implementing progressively strict regulations on ship carbon emissions, leading to the adoption of the virtual arrival (VA) method by many vessels to reduce their carbon footprint. However, the effectiveness of the traditional VA method often varies in busy ports with complex traffic organization scenarios. To address this, our study presents a novel, comprehensive model that integrates vessel scheduling with the VA approach. This model is designed to achieve a dual objective: reducing carbon emissions through Virtual Arrival and simultaneously minimizing vessel waiting times. In addition to these goals, it incorporates essential aspects of safety, efficiency, and fairness in port management, utilizing the NSGA-2 algorithm to find optimal solutions. This model has been tested and validated through a case study at Ningbo-Zhoushan port, employing its dataset. The results demonstrate that our innovative model and algorithm significantly outperform traditional scheduling methods, such as First-Come-First-Serve (FCFS) and Virtual-Arrival Last-Serve (VALS), particularly in terms of operational efficiency and reduction in vessel carbon emissions.

This article investigates the source of booming noise emanating from the tailgates of electric vehicles, along with proposed strategies to mitigate it. This study involved the measurement of booming noises during on-road vehicle tests to pinpoint their origins. Additionally, operational deflection shapes (ODS) were extracted from the tailgate vibration signals to gain insight into its dynamic behavior. Modal tests were conducted on the tailgate to determine its dynamic characteristics and compared with driving test results to reveal the mechanism responsible for tailgate-induced booming noise. It was established that such noise is primarily due to the tailgate modes resulting from a combination of rigid body motion in the fore-aft direction and deformation in the central section of the panel. An analytical model of the tailgate was developed using commercial finite element analysis software to propose measures for reducing booming noise. Experimental findings validated the model accuracy. Structural enhancements were implemented to enhance the panel stiffness and improve the connection between the vehicle and tailgate via bushings to dampen the booming noise resulting from tailgate motion. Under random force inputs, analytical results demonstrated a 13.8% reduction in maximum deformation in the tailgate model in the improved structural configuration with increased panel stiffness.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

When disposing of waste metal resources in landfills, environmental issues such as soil contamination may arise. Recycling these resources not only recovers valuable metals but also mitigates environmental pollution. Platinum (Pt), a valuable metal used in fuel cells for its high water production activity, will see increased future demand as a fossil fuel alternative. This study analyzes the environmental and resource reduction effects of recycled Pt, considering the growing emphasis on its recycling for stable supply and demand of Pt. The environmental impact and resource consumption of recycled Pt with primary Pt (from natural mines) were compared and analyzed using the Life Cycle Assessment (LCA) technique. Results revealed that resource consumption for primary Pt was 8.25E+01 kg Sb-eq./kg, significantly more than the 5.45E+00 kg Sb-eq./kg for recycled Pt. This represents an environmental reduction effect of approximately 93%. In the case of greenhouse gas emissions, primary Pt emitted 1.35E+04 kg CO2-eq./kg, while recycled Pt emitted 6.94E+02 kg CO2-eq./kg, resulting in an environmental reduction effect of approximately 95%. In conclusion, recycling Pt, compared to primary extraction, offers substantial environmental and resource reduction benefits. This study underscores the significance of recycling and highlights the potential environmental improvements achievable through sustainable practices.

The endo- and exo-N-heterocyclic carbene precursors based on camphor were prepared diastereoselectively in five synthetic steps starting from (1S)-(+)-ketopinic acid. The obtained N-heterocyclic carbene precursors were investigated in an asymmetric benzoin reaction. All new compounds were fully characterized and the absolute configurations were determined by X-ray diffraction and NOESY measurements.

The aim of this study was to investigate the performance of the developed real-time controlled bio-liquor circulation system (BCS) on a farm-scale to optimize bioreactor operation for manure treatment, and to subsequently reduce both manure-related malodor and greenhouse gas (GHG) emissions from slurry pits. The BCS was operated sequentially as per swine manure inflow (anoxic, aerobic, and settling) circulation to the slurry pit. The duration of each operational phase was self-adjusted in real-time using a novel algorithm for detecting the control point on the oxidation-reduction potential (ORP) and pH (mV)-time profiles, the nitrogen break point (NBP), and the nitrate knee point (NKP) in the aerobic and anoxic phases, respectively. The NH₄-N in the slurry manure was thoroughly removed (100%) in the bioreactor, optimizing the duration of each operational phase by accurately detecting real-time control points. The newly-developed real-time BCS decreased the nitrogen and organic matter content in the slurry pit manure by > 70%, and the potential ammonia and methane emissions by 75% and 95%, respectively. This study highlights that the this improved BCS that utilizes ORP tracking and pH (mV)-time profiles can effectively optimize BCS operation, and thereby reduce malodor and GHG emissions from swine farms.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of high-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes are investigated. The main gas-phase and solid products of plasma-chemical transformations are determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems for optimal process parameters was carried out. Using the example of hydrogen reduction of SiCl4 by the method of numerical modeling, gas-dynamic and thermal processes for this type of discharge are investigated. The impurity composition of gas-phase and solid reaction products is investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, is shown.

The increasing number of caesarean section (CS) is a major challenge in modern obstetrics. This rise is not supported by better neonatal and maternal outcomes. The prevention of unnecessary primary CS is a global priority. This study focuses on effectiveness and safety of yoga practice during pregnancy and it’s connection to perinatal outcome. We conducted a single-blinded, randomized controlled clinical trial, with healthy singleton primiparas, randomized at first trimester of pregnancy. A total of 214 participants were randomized, 106 in yoga and 108 in controls. The study group performed yoga exercise while the controls received standard antenatal care. The yoga exercises were performed once a week, lasted 90 minutes, under the supervision of a certified yoga teacher. All pregnant women from study group completed 12 yoga exercises. The results showed that the yoga group had a lower rate of urgent intrapartum CS (p-0.004) and more frequent spontaneous vaginal delivery (p-0.009), while the control group had a higher rate of induced labour (p-0.032). Conclusion: Yoga practice in pregnancy is a promising intervention that has a potential to decrease intrapartum urgent CS rates and assures natural and spontaneous vaginal birth; it’s highly recommendable to healthy pregnant women.

This comprehensive review delves into the intricate relationship between Sodium-GlucoseCo-Transporter 2 (SGLT2) inhibitors and AF, highlighting the multifaceted actions of thesedrugs and their significant cardiovascular benefits. Mechanisms: SGLT2 inhibitors inducesubstantial hemodynamic changes, impacting blood pressure, adipose tissue function, andinflammation. They enhance glycemic control while potentially reducing oxidative stress andinflammation, and they modulate atrial electrophysiology, collectively contributing to the reductionof AF risk. Clinical Evidence: This review synthesizes a wealth of clinical evidence,drawing from observational studies and randomized controlled trials, consistently demonstratinga correlation between SGLT2 inhibitors, particularly dapagliflozin and empagliflozin, anda decreased risk of AF. This protective effect is most pronounced in patients with type 2 diabetesand heart failure, underscoring their potential as therapeutic agents for high-risk populations.Potential Benefits: SGLT2 inhibitors offer a spectrum of potential benefits, includingsubstantial reductions in AF risk, particularly in patients with type 2 diabetes and heart failure.These drugs have consistently demonstrated benefits in reducing heart failure hospitalizations,cardiovascular mortality, and stroke risk, which indirectly contribute to better AF management.Furthermore, SGLT2 inhibitors exhibit renoprotective properties by slowing theprogression of chronic kidney disease and reducing albuminuria, offering substantial benefitsfor AF patients with comorbid kidney disease. Metabolic improvements involving weight loss,blood pressure reduction, and favorable changes in lipid profiles contribute to enhanced cardiovascular health and reduced AF risk. Originally designed for diabetes management, thesemedications offer a holistic approach to AF risk reduction, particularly in patients with type 2diabetes and heart failure.

Ultrasonic sensors are inexpensive and can take measurements with high accuracy, even with simple hardware configurations, so they are used in various fields. When multiple ultrasonic sensors exist in the measurement space, crosstalk occurs due to other nodes, which causes measurement errors. Crosstalk includes not only receiving homogeneous signals from other nodes, but also overlap by other signals, and interference by heterogeneous signals. This paper proposes a method that uses frequency sweep keying modulation to be robust against overlap and a faster region-based convolutional neural networks (R-CNN)-based demodulator to reduce the interference caused by heterogeneous signals. The demodulator works by training faster R-CNN with the spectrograms of various received signals and classifying the received signals using a faster R-CNN. Experiments implementing an ultrasonic crosstalk environment showed that compared to on-off keying (OOK), phase-shift keying (PSK), and frequency-shift keying (FSK), the proposed method can implement CDMA even with shorter codes, and is robust against overlap. Compared to correlation-based frequency sweep keying, the time-of-flight error was reduced by approximately 75%. While existing demodulators did not consider heterogeneous signals, the proposed method ignored approximately 99% of the OOK and PSK signals, and approximately 79% of the FSK signals. The proposed method performs better than the existing methods and is expected to be used in various applications.

The Global Hunger Index (GHI) is a vital tool for assessing and understanding the state of hunger and food security across the world. In this review article, we examine the GHI scores of various countries in the years 2000, 2008, 2015, and 2023. We aim to explore the changes in GHI scores over this period, identify trends, and discuss the implications for global food security. The GHI provides a comprehensive snapshot of the world's progress in reducing hunger, and this analysis sheds light on the successes and challenges faced by different countries.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

This article presents a study on the aerodynamic drag of a generic dual-axle flatbed trailer and explores ways to reduce the drag using appendable drag-reducing devices. The primary sources of drag originated from the van and trailer’s rear, along with the trailer’s wheels. The most effective initial device for reducing drag was a full trailer underside cover which offered a 7% drag reduction. Additionally, ladder racks, dropsides, and rear gates were studied, and it was found that protruding ladder racks significantly increased drag. Rear gates added large amounts of drag and should be removed and stored when not needed. The study also explored novel mid-section devices that increased the van’s base pressure and reduced drag. An axle test revealed that drag for single, dual, and triple axle trailers was very similar in direct flow, but different in yawed flow. A drawbar length test showed a near-linear relationship between drawbar length and drag, manifesting as a 1.7% change in drag per 250mm change in drawbar length. Several novel modifications were made to the trailer, including fitting six unique appendable devices, which offered a total 7.3% drag reduction. A novel rear van device known as the Multi-Stage Converging Cavity was introduced which reduced drag by nearly 18%. When all the devices were used together, a total 25% drag reduction was observed for the van-trailer combination.

Nickel is widely used in industrial processes and plays a crucial role in many applications. However, most of the nickel resource mainly exists as nickel oxide in laterite nickel ore with complex composition, resulting in difficulty in upgrading the nickel content using physical separation methods. In this study, high-grade ferronickel concentrates were obtained through a carbothermal reduction and magnetic separation using laterite nickel ore and anthracite as raw materials. The effects of different types of additives (CaF2, Na2SO4 and H3BO3), carbon ratio (nc/no in metal oxides) and grinding time on the recoveries and grades of ferronickel concentrates were experimentally investigated, along with the microstructure and chemical composition of the products. CaF2 was proved to be the primary active additive in the aggregation and growth of the ferronickel particles, and the improvement of the grade of the product. Under the optimal conditions of CaF2 addition of 12 wt.%, carbon ratio of 1.4, and grinding time of 240 s, high-grade magnetically separable ferronickel concentrate with nickel grade 8.93 wt.% and iron grade 63.96 wt.% was successfully prepared. This work presents a practical method for the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore, contributing to the development of strategies for the sustainable extraction and utilization of nickel resources.

A wide variety of substances have been used to anaesthetise invertebrates, but many are not anaesthetics and merely incapacitate animals, rather than preventing pain. Much is now known about the mode of action of modern clinical and veterinary anaesthetics because of their use on human beings and other vertebrates. In essence, the role of an ideal general anaesthetic is to act as a muscle relaxant, an analgesic, an anaesthetic and an amnesic. To achieve all these properties with a single substance is difficult and various adjuvants usually need to be administered, resulting in a cocktail of drugs. In a clinical setting, the vast majority of patients are unaware of surgery being carried out and have no memory of it, so they can claim to have felt no pain, but this is much more difficult to demonstrate in invertebrates. Here we show that 1% MgCl2, a muscle relaxant, is a useful adjuvant for the clinical anaesthetic isoflurane on Octopus vulgaris when applied for 10 minutes before the clinical anaesthetic. After this, full anaesthesia can be achieved in 5 minutes using only 1% isoflurane and from which full recovery takes place rapidly in about 10 to 15 minutes. This reduces stress on the animal and minimises the quantity of anaesthetic used.

In verifying programs for embedded systems, it is essential to reduce the verification time because state explosion may occur in model checking. One solution is to reduce the number of interrupt handler execution. In particular, when periodic interrupts such as timer interrupts are incorporated, it is necessary to know the physical time. In this paper, we define a control flow automata (CFA) that can handle time and propose an algorithm based on interrupt handler execution reduction (IHER). The proposed method reduces the number of interrupt executions, including timer interrupts. A case study verifies the effectiveness of this algorithm.

The increasing prevalence of periprosthetic femoral fractures, specifically in the vicinity of the hip, has emerged as a significant issue in recent times. Consequently, there is a need for a thorough examination to enhance the effectiveness of management and treatment approaches. The findings emphasized a significant disparity in the occurrence and characteristics of these fractures, as multiple studies have highlighted the efficacy of various treatment strategies, such as open reduction and internal fixation, as well as the utilization of cortical strut allografts. Furthermore, the research has identified potential risk factors that have an impact on the characteristics of fractures, providing valuable insights that could be crucial in the development of preventive strategies. This research provides a thorough examination of periprosthetic femoral fractures, highlighting the importance of a cohesive treatment algorithm to improve the handling of such fractures. Moreover, it promotes the need for a collaborative endeavor in conducting research in this field, cultivating a more profound comprehension that has the potential to drive progress in therapeutic approaches, ultimately enhancing patient results over an extended period of time. It is crucial that forthcoming research endeavors persist in expanding upon these discoveries, striving towards a unified methodology in tackling this substantial clinical obstacle.

This work investigates a new nanostructured gas-diffusion-layer (nano-GDL) to improve performance of air-cathode Single-Chamber-Microbial-Fuel-Cells (a-SCMFCs). The new nano-GDLs improves the direct oxygen-reduction-reaction by exploiting the best of nanofibers from electrospinning in terms of high surface ratio to volume and high porosity, and laser-based processing to promote adhesion. Nano-GDLs by electrospinning were fabricated directly collecting two nanofibers mats on the same carbon-based electrode, acting as the substrate. Each layer was designed with a specific function: water resistant, oxygen permeable polyvinylidene-difluoride (PVDF) nanofibers served as a barrier to prevent water-based electrolyte leakage, while an inner layer of cellulose nanofibers was added to promote oxygen diffusion towards the catalytic sites. The maximum current density obtained for a-SCMFCs with the new nano-GDLs is (132.2 ± 10.8) mA m^-2, and it doubles the current density obtained with standard PTFE-based GDL (58.5 ± 2.4 mA m^-2), used as reference material. The energy recovery (EF) factor, i.e. the ratio of the power output to the inner volume of the device, was then used to evaluate the overall performance of a-SCMFCs. a-SCMFCs with nano-GDL provided an EF value of 60.83 mJ m^-3: one order of magnitude higher than the value of 3.92 mJ m^-3 obtained with standard GDL

Maritime ports represent an important ecosystem for pollutant emissions and, taking into account the ongoing energy transition, need to adopt new solutions to mitigate current emission levels. These emissions are partially avoidable if ships and vessels docked at the port use electric energy to feed their internal power needs instead of using their internal combustion engines. In Europe, there is an ongoing discussion on including such emissions in the European Emissions Trading System which will represent added costs for maritime operators. Onshore Power Supply systems can contribute to the ongoing energy transition by allowing the use of electric power to feed docked ships. As a first step to contribute to the development of Onshore Power Supply solutions, it is necessary to evaluate the added power needs that these systems would represent for the port. This paper presents a methodology that allows port operators to verify, straightforwardly and transparently, their power needs for Onshore Power Supply applications. The methodology is based on the historical data of docked ships at the port or quay level and provides an energy analysis of each type of vessel to determine the power to be installed at the port so that it is possible to supply energy to different types of ships and vessels simultaneously. Additionally, the implemented methodology provides economic and technical decision support factors by comparing the fuel costs with electric power costs, assessing the potential for this transition to Onshore Power Supply. The methodology is validated using a real case study for the port of Lisbon and obtained results demonstrate the potential for the installation of Onshore Power Supply in medium to large-dimension maritime ports.

The changes in consumer lifestyles have raised awareness of the variety of food options and packaging technologies. Active and smart packaging represents an innovative technology that serves to enhance the safety and quality of products. Smart packaging, as a subset of this technology, entails the integration of additives into packaging materials, thereby facilitating the preservation or extension of product quality and shelf life. This technological approach stimulates a heightened demand for safer food products with prolonged shelf life. Active packaging predominantly relies on the utilization of natural active substances. Therefore, the combination of active substances has a significant impact on the characteristics of active packaging particularly on polymeric blend like Polylactic acid (PLA) as a matrix. So, This review will summarize and explains how the addition of natural active agents influenced the properties related to the performance of active packaging through systematic analysis, providing new insights about the relationship between the types of active agents on physical-mechanical properties, bacterial colony reduction, and applications in foods packaging such as meat, fish, fruit, and vegetables. Through their integration, the market for active and smart packaging systems is expected to have a bright future.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

Four different Mn and Re catalysts for electrochemical CO2 reduction have been studied by IR spectroelectrochemistry (SEC) in dry acetonitrile. In the case of Mn(apbpy)(CO)3Br (apbpy= 4(4-aminophenyl)-2,2’-bipyridine) SEC suggests that a very slow catalytic reduction of CO2 occurs in acetonitrile also in the absence of proton donors, but at rather negative potentials. On the contrary, the corresponding Re(apbpy)(CO)3Br clearly displays a slow catalytic conversion already at the first reduction potential. Switching to saturated CO2 solutions in a mixture of acetonitrile and 5% of water as proton donor, the SEC of Mn(apbpy)(CO)3Br displays faster catalytic behavior.

In the evolving landscape of higher education, St. Michael's College (SMC) recognizes the significant impact of the COVID-19 pandemic on student welfare. This paper emphasizes the critical importance of addressing mental health, time management, and stress in the college environment, underlining their influence on academic success and personal growth. The call to action urges students to prioritize their well-being. Diverse cultural and religious perspectives, including Islam, emphasize the importance of a balanced mind and body. The wide-ranging literature review uncovers empirically supported strategies for mental health, time management, and stress reduction. Personal autonomy emerges as crucial in addressing these challenges. This study underscores the importance of these dimensions, calls for student action, and highlights the diversity of perspectives contributing to holistic well-being.

As broiler farming facilities have become larger and more concentrated in response to external environmental changes, there is a possibility of increased concentrations of fine dust and aerosols inside these facilities due to enclosure. In particular, workers are exposed to high concentrations of organic particulate matter and harmful gases while performing their tasks, and as they age, they become more vulnerable to respiratory diseases. It is essential to directly monitor the concen-trations to which workers are exposed, along with the spatial distribution of aerosols inside broiler house. In this study, we analyzed the regional aerosol concentrations using passive samplers in commercial tunnel-ventilated broiler farms. Simultaneously, we employed active samplers at the height of the workers' breathing zones to monitor real-time aerosol concentrations by particle size along their work routes. Spatial aerosol concentrations generally increased from the inlet to the exhaust in the breathing zone. The average aerosol concentrations were TSP -1,042 µg/m³, PM-10 718 µg/m³, and PM-2.5 137 µg/m³. To analyze the workers' exposure environments, we categorized the tasks in the barn into Static work period (SWP) and Moving work period (MWP) based on video analysis. The results showed that during MWP, fine dust concentrations exceeded the standards by up to 214%. Particularly, during MWP, the concentrations were 1.74 times higher for TSP, 1.40 times higher for PM-10, and 1.22 times higher for PM-2.5 compared to SWP. It was observed that during the movement of workers, physical generation of particles around 10 µm, such as feces, feed, and bedding, occurred due to the movement of chicken, which influenced the aerosol concentration.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

The combination of e-commerce and the green economy allows enterprises to distribute their green products directly to consumers through Internet channels. This paper investigates the impact of service spillovers on emission reduction and channel decisions in a two-echelon supply chain,in which the supplier is a Stackelberg leader and the retailer is a follower.By comparing the equilibrium outcomes of the single-channel and dual-channel supply chain in a setting with and without retail services, we observe that the supplier prefers to encroach on the market when services that retail locations provide largely spillover to and benefit the direct sales channel. Contrary to popular belief, a higher degree of service spillovers is beneficial for the retailer to get more returns under the dual-channel structure, whereas supplier encroachment will lead to a decline in the service level if the spillover degree is relatively low. In addition, the emission reduction level of products under supplier encroachment is always higher than that employed in the single-channel structure if consumers have both low-carbon preference and high degree of service sensitivity. Furthermore, we extend the equilibrium decisions under a carbon cap-and-trade (CCT) mechanism; the results fully verify the above conclusions. Interestingly, the implementation of a carbon price not only motivates carbon emission abatement and supplier encroachment, but also helps achieve a win-win outcome for supply chain members when service spillovers happen.

The weight loss process variables of alkali-treated micropolyester woven fabric were optimized and reported in this study. The grey relational analysis (GRA) with the help of the Taguchi technique was efficiently used to optimize the key variables of this process. The caustic soda concentration, treatment temperature, and weight loss machine speed were considered the control or design parameters. The weight reduction percentage, air permeability, tensile strength, and thermal resistance of alkali-treated woven polyester fabrics were also considered as responses in this study. The experiments were implemented according to a 33 full factorial design. The levels of the control parameters which yield the maximum weight reduction, tensile strength, air permeability, and minimum thermal resistance of the treated polyester fabrics were found to be NaOH concentration and treatment temperature with the highest levels, and machine speed with the lowest level. This means that a 27% caustic soda concentration, treatment temperature of 125 OC, and machine speed of 40 m/min exhibited the optimum properties of the treated micropolytester fabrics. It is also proved that the treatment temperature is the most influential factor affecting the micropolyester fabric’s properties. The confirmation test which was carried out in this study confirmed that the GRA improved the alkali-treated polyester fabric properties.

With the changes in the spatial structure of China's economic development, urban clusters have become the primary carriers of China's regional economy and green growth. The article uses annual data from 2010 to 2021 to study the carbon emission characteristics and carbon reduction pathways of 36 cities in the Yangtze River Delta region. Firstly, cities in the Yangtze River Delta region are divided into six carbon emission types based on decoupling elasticity coefficient and carbon intensity indicators. Then, the STIRPAT model is used to regress the panel data of different carbon emission types for 11 years, analyze the driving factors of carbon emissions, and develop differentiated carbon emission reduction paths for cities with six carbon emission types. According to the results, the city of Type I needs to accelerate low-carbon technology innovation, Type II needs to improve energy efficiency and strengthen low-carbon technology research and development, Type V needs to suppress foreign investment in high energy consumption and high emission projects in the local area, Type VI needs to accelerate the process of new urbanization and optimize industrial structure. Types III and IV have not received effective emission reduction paths, and further research is required on other emission reduction policies and measures.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

Ever since the tremendous success of the rapid vaccine development against COVID‑19, its availa-bility, distribution, and deployment have been a significant concern; however, evidence suggests that vaccine hesitancy has become a greater problem. Therefore, trust in vaccines is crucial and critically dependent on regimes' ability to communicate the benefits of immunization. This study investigated ideas on ways to reduce barriers to COVID-19 vaccination uptake. It explores methods to overcome COVID-19 vaccine barriers through qualitative research: interviews and group discussions involving healthcare providers, administration personnel, teachers, and individuals with chronic conditions across urban (Mombasa) and rural (Kilifi) Kenya. Audio-recorded discussions were transcribed and thematically analyzed across locations. Five themes emerged in our results regarding how to reduce barriers to the COVID vaccine in the context of Kenya, including awareness campaigns, engaging diverse stakeholders, using various communication techniques, capacity building to increase vac-cination centers and trained staff, and lastly, revising relevant government health policies and guidelines. These results indicate the importance of adopting multiple approaches, as no single strategy could boost vaccine acceptance. Moreover, this study provides recommendations for con-ceiving actionable interventions to potentially boost vaccine demand and maintain routine immun-ization in Kenya.

In hydraulic systems, energy dissipation can be significant. The pressure drops that can occur in the hydraulic circuit, influenced by the adopted drive architecture, result in an absorbed power often significantly greater than that required by the mechanical system. In this paper, a comparative study of energy efficiency among five drive common architectures in industrial hydraulic axes is carried out. The analysis is applied to a hydraulic blanking press with variable speed and force, a fairly frequent industrial system, e.g. in the production of semi-finished brass products. Standard, regenerative, high-low, variable displacement pump and variable speed drive for a fixed displacement pump configurations have been analysed and compared. An adequate and optimized sizing of the various components of the system has been carried out in each case and subsequently the energy consumption has been estimated for a load cycle common to all the considered cases. The results show that the choice of power generation architecture of the hydraulic system has a very significant impact on energy efficiency and consequently operating costs and carbon footprint. The performed quantification of the potential energy efficiency of the considered drive architectures can be very useful in guiding energy-conscious choices.

Parametric models have been widely used in pertinent literature for reconstructing, modifying and representing a wide range of airfoil and/or hydrofoil profile geometries. Design spaces corresponding to these models can be exploited for modeling and profile-shape optimization under various performance criteria. Accuracy requirements, along with the need for modeling local features, often lead to high-dimensional design spaces that hinder the process of shape optimization and design through analysis. In this work, we propose a shape-informed dimensional reduction approach that attempts to tackle this deficiency by producing low-dimensional latent design spaces that can be efficiently used in shape representation and optimization. Furthermore, geometric moments are introduced in an attempt to cost-effectively capture analysis-relevant information that is generally expensive to produce. Specifically, geometric integral properties, although intrinsic features of the shape, are quite commonly related to performance indicators employed in performance optimization and therefore provide a cost-effective physics-informed component in the description of the design in the latent space. To this end, we employ the generalized Karhunen-Loeve expansion to produce a shape- and physics-informed subspace retaining the highest possible geometric variance and robustness, that is, lack of invalid designs. At the same time, a series of shape discretizations, encoding the foil's shape profile, are examined with regards to their effect on the resulting latent space's quality and efficiency. Our results demonstrate a significant reduction in the dimensionality of the original design space while maintaining a high representational capacity and a large percentage of valid geometries that facilitate fast convergence to optimal solutions in performance-based optimization.

Cadmium (Cd) is a major heavy metal pollutant and a significant cause of abiotic stress in the environment. Organisms have developed various pathways to protect themselves against Cd stress. MYB protein is a large transcription factor family in plants. Many members of the family have been found to regulate developmental processes and stress responses. However, the function and mechanism of MYB116 are far from clear. In a recent study, we found that MYB116 of Chinese cabbage enhances Cd tolerance in yeast. BrMYB116 is transiently inducible by Cd treatment in Chinese cabbage. When expressed in yeast cells, it enhances tolerance against Cd stress and reduces Cd accumulation in the cells. Further analysis shows that BrMYB116 protein enhances Cd tolerance in yeast cells by activating one target gene that encodes the facilitator of iron transport 3 (FIT3). ScFIT3 is activated through specific binding with its promoter. More importantly, the expression of ScFIT3, leads to a substantial reduction of Cd accumulation in both yeast and Chinese cabbage. This finding implies that a similar network may exist in other biological systems, which presents a promising avenue for enhancing Cd tolerance in plants and developing Cd-resistant crops.

Despite providing some critical financial services to support the operation of Emissions Trading Systems (ETS), such as increasing market liquidity and price visibility and allowing operators to hedge against future fluctuations, there is growing concern about the potential threat of financial actors' speculation behaviour to the ETS's effectiveness. To confirm or alleviate the fear associated with such concern, we employ both ex-post and ex-ante approaches to determine the role of speculation in the emission reduction effect of the ETS and its forecasting power in predicting climate change. In addition to confirming carbon prices and the speculation behaviour of the emissions non-compliance actors in the ETS as accurate predictors of climate change, we also show that they both matter in the emission reduction effect of the ETS. We use several verifiable econometric approaches to select the Feasible Quasi Generalised Least Squares (FQGLS) as the best estimator for addressing some of the biases in climate change predictability. We demonstrate that a predictive model combining the complementing dynamics of the EST emissions compliance and emissions non-compliance features forecasts climate change more accurately. We demonstrate the robustness of our findings for both in-sample and out-of-sample forecasts and across different forecast horizons by using alternative approaches to evaluate forecast performance.

International trade has been one of the most significant economic activities among countries, and its contributions towards a country’s economic growth and sustainable development have been acknowledged. In recent times, international trade and global trade networks have received preeminent attention due to the sharp growth in trade volumes and its contributions to poverty reduction and general welfare. Despite the growth in global trade volumes, there are worrying concerns about the unprecedented changes in international trade patterns and growing imbalances in trade in recent times. Whereas China’s trade volumes have more than tripled over the last decades and have maintained the largest trade surplus spot ahead of Germany, other major trade surplus countries such as Japan, the USA, etc. have become trade deficit countries with their trade volumes increasing at a much slower pace. In view of the growing imbalances in global trade volumes, we use an augmented gravity model of trade that incorporates social network measurement, the real effective exchange rate which is a measurement of international competitiveness, as well as the Linder theory of trade, to investigate the factors that determine the export performance of countries. Using data from 51 countries for 41 years, our results indicate that the GDP of both the home country and the partner country affects the home country’s exports positively. Similarly, the real effective exchange rate REER, trade openness OPEN and dummy variables BORDER, ENGLISH, and EU have produced positive and statistically significant coefficient estimates, and these are in line with our theoretical expectations.

Diabetes mellitus is a chronic disease that affects millions of people worldwide. Article focuses on detecting the presence of diabetes in patients using microarray gene data obtained from the pancreas. Handle the high-dimensional nature of the data, four different dimensionality reduction techniques, namely Bessel Function, Discrete Cosine Transform (DCT), Least Square Linear Regression (LSLR), and Artificial Algae Algorithm (AAA) are used. After reduced the data, Meta-heuristic algorithms are applied like Dragonfly Optimization Algorithm (DOA) and Elephant Herding Optimization Algorithm (EHO) for feature selection. Ten classification techniques are using to classify the data in both the format like without feature selection method and with feature selection method. The classification techniques are Non-Linear Regression (NLR), Linear Regression (LR), Gaussian Mixture Model (GMM), Expectation Maximum (EM), Bayesian Linear Discriminant Classifier (BLDC), Logistic Regression (LoR), Softmax Discriminant Classifier (SDC), Support Vector Machine (SVM) with linear kernel, Support Vector Machine (SVM) with polynomial kernel, and Support Vector Machine (SVM) with Radial Basis Function (RBF) kernel. Results showed that the AAA with SVM(RBF) achieved an accuracy of 90% without feature selection. However, when feature selection was applied, with EHO of AAA with SVM(RBF) exhibited the highest accuracy of 95.714%, followed closely by with DOA of AAA with SVM (RBF) at 94.28%.

In this study, we created a series of N, S, and P-doped and co-doped carbon catalysts using a single graphene nanoribbon (GNR) matrix and thoroughly evaluated the impact of doping on ORR activity and selectivity in acidic, neutral, and alkaline conditions. The results obtained showed no significant changes in the GNR structure after the doping process, though changes were observed in the surface chemistry in view of the heteroatom insertion and oxygen depletion. Of all the dopants investigated, nitrogen (mainly in the form of pyrrolic-N and graphitic-N) was the most easily inserted and detected in the carbon matrix. The electrochemical analyses conducted showed that doping impacted the performance of the catalyst in ORR through changes in the chemical composition of the catalyst, as well as in the double-layer capacitance and electrochemically accessible surface area. In terms of selectivity, GNR doped with phosphorus and sulfur favored the 2e- ORR pathway, while nitrogen favored the 4e- ORR pathway. These findings can provide useful insights into the design of more efficient and versatile catalytic materials for ORR in different electrolyte solutions, based on functionalized carbon.

Background and objectives: Thoracolumbar fracture – dislocations (AO type C) are rare injuries that occur due to very high-energy trauma, and the result is transitional and rotational instability of the spinal column and neurological impairment. Several reduction maneuvers have thus far been published, each of which can be of use in certain specific situations. We developed a novel modification to the previously described reduction technique. Materials and methods: This is a retrospective review of the management of thoracic AO type C fracture-dislocations managed with a modified novel reduction technique. The success of the reduction and intraoperative iatro-genic complications such as dural tear and screw pull out were the outcomes analyzed. Results: A total of 4 cases were successfully reduced with this novel reduction technique. We did not note any complications such as a dural tear or screw failure with this modified novel reduction tech-nique. Conclusion: The novel modification to the reduction technique employed in the management of thoracic fracture-dislocations resulted in a successful reduction without the risk of iatrogenic complications due to the reduction maneuver.

Novel effluent treatment solutions for dangerous organic pollutants are crucial worldwide. In recent years, chemical reduction using noble metal-based nanocatalysts and NaBH4, a reducing agent, has become common practice for eliminating organic contaminants from aquatic environments. We suggest a straightforward approach to synthesizing magnetic cellulose nanocrystals (CNC) modified with magnetite (Fe3O4) and silver nanoparticles (Ag NPs) as a catalyst for organic contamination removal. Especially, Ag NPs were decorated on the CNC surface without reducing agents or stabilizers by reducing AgNO3. XRD, FE-SEM, TEM, EDX, VSM, BET, and zeta potential tests characterized the Ag/Fe3O4/CNC nanocomposite. The nanocomposite's catalytic activity was tested by eliminating 4-nitrophenol (4-NP) and organic dyes methylene blue (MB) and methyl orange (MO) in an aqueous solution at 25 oC. The Ag/Fe3O4/CNC nanocomposite reduced 4-NP and decolored these hazardous organic dyes in short time (2 to 5 min) using a tiny amount of catalyst (2.5 mg for 4-NP and 15 mg for MO and MB). The magnetic catalyst was removed and reused three times without losing catalytic activity. This work shows that the Ag/Fe3O4/CNC nanocomposite can chemically reduce harmful pollutants in effluent for environmental applications.

Rather high speed of modern water bikes that they develop using only human muscle power increases their popularity. For example, the maximum speed of prototypes reaches the value 3 m/s. Similar vehicles can be used not only for recreation and fitness, but also for transportation. To increase their speed and tonnage, we recommend improving the pontoon shape and using electrical power. The total drag and maximal speeds of the vehicles with the human muscle and electrical power are estimated. Expected success in improving the pontoon shape opens wide prospects for the use of these special shaped hulls in shipbuilding.

In this paper the application of the solid-state cooling based on barocaloric effect in the cold food supply chain is investigated. Barocaloric solid-state technology is applied to the final chain links of the cold food supply chain, regarding the steps of retail and domestic conservation. In this context a barocaloric cooler with regard to food needing to be kept at 5°C (273 K), in order to operate with a promising cooling technology that result energy efficient and environmentally friendly. The categories of food interested in the investigation are meets and fresh food products like soft cheese, yogurt, milk. The energy performances of the barocaloric system have been carried out and compared with a commercial vapor compression refrigerator of a similar size, both operating with R600a under the same working conditions. Basing on the following consideration one can conclude that barocaloric cooling is a favourable technology to be employed in the last link chains of the cold food supply chain if the system operates in ABR cycle at frequencies between 1.25 and 1.50 Hz with a regenerator made of acetoxy silicone rubber as solid-state refrigerant and 50%EG-50%water mixture as heat transfer fluid flowing at the optimal velocity of 0.15 m s-1 that guarantees an appropriate trade-off between the temperature span, the cooling power and the coefficient of performances. Under these conditions the barocaloric system overperforms the domestic vapor compression cooler operating with R600a.

The design and fabrication of low-cost catalysts for highly efficient oxygen reduction is of paramount importance for various renewable energy-related technologies, such as fuel cells and metal-air batteries. Herein, we report the in situ growth of Fe3N nanoparticles encapsulated N-doped carbon nanotubes on the surface of flexible biomass-derived carbon cloth (Fe3N@CNTs/CC) via a simple one-step carbonization process. Taking advantage of its unique structure, Fe3N@CNTs/CC was employed as a self-standing electrocatalyst for oxygen reduction reaction (ORR) and possessed high activity as well as excellent long-term stability and methanol resistance in alkaline media. Remarkably, Fe3N@CNT/CC can directly play the role of both gas diffusion layer and electrocatalytic cathode in a zinc-air battery without additional means of catalyst loading, and display higher open circuit voltage, power density, and specific capacity in comparison with the commercial Pt/C catalyst. This work is anticipated to inspire the design of cost-effective, easy-preparation, and high-performance air electrodes for advanced electrochemical applications.