Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

The expansion of food production is getting more important due to a rising world population, which is relying on food security on a regional and local scale. Intensive food production systems create a negative impact on the regional ecosystem because of agrochemical pollution and nutrient rich water discharges into nearby rivers. Furthermore, these systems are highly depending on regional water resources causing water scarcity and soil erosion due to the overexploitation of natural resources in general. The objective of this article is to review the water usage in the two most water intensive food production systems, agriculture and aquaculture showing lacking areas, like system management and climate change, which must be considered in the implementation of sustainable water footprint. In addition, the review includes an analysis if the combination of both production system into aquaponic food production and the possibilities of water saving. There are a variety of water footprint analyses for crop and aquatic animal production, but there is also a lack of information about the system management including irrigation systems, system cleaning processes, water substitution, pond removal, evaporation due to climate change and especially in aquaculture, the water footprint of industrial elaborated fish feed.

This article addresses the emergence of a niche for sustainable agricultural production in the province of García Rovira, Colombia. It examines the intervention of the Colombian planning regime, which implements agendas for sustainable territorial development. However, these agendas are not adequately aligned with provincial realities, resulting in a productive decline. From a multi-level perspective, a niche of production linked to the landscape is identified, highlighting sustainable practices and innovation. The study seeks to understand how planning influences the emergence of such niches and what factors boost their transition to sustainability. Through a mixed methodology, growing sectors are highlighted, and the profiles of the producers involved are outlined. The main conclusion is that the planned intervention is inefficient, as the niche of sustainable production emerges without its clear influence. Therefore, it is proposed to re-evaluate planning using alternative analysis frameworks to detect emerging productive dynamics, serving as a basis for future plans.

: Climate change necessitates urgent actions to mitigate carbon dioxide (CO2) emissions from fossil fuel-based energy generation. Among various strategies, the deployment of carbon capture and storage (CCS) solutions are critical for reducing emissions from point sources such as power plants and heavy industries. In this context, cryogenic carbon capture (CCC) via desublimation has emerged as a promising technology. While CCC offers high separation efficiency, minimal downstream compression work, and integration potential with existing industrial processes, challenges such as low operating temperatures and equipment costs persist. Ongoing research aims to address these hurdles in order to optimize the desublimation processes for widespread implementation. This review consolidates diverse literature works, providing insights into the strengths and limitations of CCC technology, including the latest pilot plant scale demonstrations. The transformative potential of CCC is first assessed on a theoretical basis, such as thermodynamic aspects and mass transfer phenomena. Then, recent advancements in the proposed process configurations are critically assessed and compared through key performance indicators. Furthermore, future research directions for this technology are clearly highlighted.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

Investments in small and medium-sized anaerobic digestion facilities have the potential to boost biogas production in Greece and other EU countries. This study aimed to evaluate the economic feasibility of anaerobic digestion facilities equipped with combined heat and power (CHP) units ranging from 50 to 400 kW, while treating livestock waste. For this purpose, data were gathered from various livestock operations (dairy cattle, poultry, swine, dairy sheep and goat) regarding their annual production, revenues, electricity and fuel usage, and waste generation. Waste samples were then collected and analyzed to assess their biochemical methane production potential. The capital and operational costs of anaerobic digestion facilities, from 50 and 400 kW, were calculated using the equations developed within the “eMT cluster” project. Findings indicate that current feed-in tariffs (FIT) of 0.21 € kWh-1 are insufficient to incentivize investment in anaerobic digestion facilities with capacities below 250 kW, highlighting the need for increased FIT rates or capital expenditure subsidies. Recommendations include shifting towards simplified technology and business models with reduced farmer involvement, coupled with supportive legislative framework and long-term electricity price guarantees. These measures are expected to foster the implementation of anaerobic digestion projects in the animal husbandry sector.

This case study focuses on exploring the potential of biogas as a direct substitute for conventional fossil fuels in industrial applications. Instead of being limited to its common uses as a vehicle fuel or for power generation, this research aims to investigate how biogas can be integrated into industrial processes as an advanced and sustainable energy solution. By conducting a detailed analysis of the financial implications associated with the utilization of landfill gas and gas derived from biomass, a comprehensive understanding of their practical applications in the industrial sector can be obtained. This research goes beyond a superficial examination and delves into the intricate aspects of incorporating biogas as a viable alternative fuel source. When we say that utilizing biogas is technically feasible, it means that the necessary infrastructure and technologies are available to support its integration into industrial processes. This implies that there are existing methods and systems in place that can efficiently harness and utilize biogas for various industrial applications. These technologies ensure a seamless transition from conventional fossil fuels to renewable energy sources, leading to a more sustainable and environmentally friendly industrial landscape. Moreover, the statement that utilizing biogas is economically feasible emphasizes that the financial viability of employing biogas in industrial processes is advantageous. This research explores the potential cost savings and benefits associated with substituting conventional fuels with biogas. By carefully examining the economic aspects, such as initial investments, operational costs, and potential revenue streams, a comprehensive understanding of the financial impact of adopting biogas solutions in the industrial sector can be gained. By expanding and broadening the understanding of the technical and economic feasibility of biogas integration, this research aims to provide valuable insights into the potential of advanced biogas solutions for industrial applications. Indeed, to make biogas a viable and sustainable option as a raw material, it is necessary to establish farming subsidies and financial support specifically tailored for biogas production, similar to the existing support provided for food production. These subsidies and financial incentives play a crucial role in promoting and encouraging the growth of the biogas industry. By establishing such support systems, farmers and other stakeholders in the agricultural sector can be incentivized to participate in the production of biogas. This can involve the utilization of agricultural waste, organic residues, or dedicated energy crops for biogas generation. The financial assistance can help offset the initial investment costs, provide incentives for production, and ensure the economic viability of biogas projects. Moreover, when considering large-scale landfills or situations where industrial demands for energy are relatively low, landfill gas becomes a viable and practical option. Landfill gas, which is generated by the decomposition of organic waste in landfills, can be harnessed and utilized for various industrial purposes. This not only helps in managing waste but also provides a valuable source of renewable energy. In summary, while farming subsidies and financial support are crucial for promoting biogas production, landfill gas remains a viable option for large landfills or situations with minor industrial demands. The combination of these two approaches offers a comprehensive outlook on utilizing biogas as a renewable energy source for industrial applications.

Membrane gas absorption technology has been considered as a promising approach to mitigate CO2 emissions from power plants. The aim of this study is to evaluate the environmental impacts of CO2 absorption and desorption processes by hollow fiber membrane contactors using life cycle assessment methodology. On the basis of ReCipe 2016 Midpoint and ReCipe 2016 Endpoint methods, the research results show that, membrane gas absorption system exhibits the lowest environmental impacts across the majority assessed categories in comparison with chemical absorption and membrane gas separation systems. The CO2 capture process via membrane gas absorption has the most significant impact on METP category, with heat consumption as the primary contributing factor accounting for 55%, followed by electricity consumption accounting for 43.1%. According to the sensitivity analysis, heating by natural gas shows a better performance than other heat supply sources in improving overall environmental impacts. In addition, the increasing utilization of renewable energy in electricity supply reduces the global warming potential, fossil resource consumption and ozone formation.

In this study, a comprehensive review on production scheduling based on reinforcement learning (RL) techniques using bibliometric analysis has been carried out. The aim of this work is, among other things, to point out the growing interest in this domain and to outline the influence of RL as a type of machine learning on production scheduling. To achieve this, the paper explores production scheduling using RL by investigating the descriptive metadata of all pertinent publications contained in the Web of Science database. The study focuses on a wide spectrum of publications spanning the years between 1998 and 2023. The findings and recommendations of this study can serve as new insights for future research endeavors in the realm of production scheduling using RL techniques.

Acemetacin (ACM) is a new non-steroidal anti-inflammatory drug with anti-inflammatory, analgesic, and antipyretic effects. However, the poor water solubility and gastrointestinal side effects limit its use. Recently, the co-amorphous (CAM) strategy has attracted great interest to improve solubility for poorly water-soluble drugs, and basic amino acids have the potential to protect the gastrointestinal tract. In order to develop highly efficient and low toxic ACM formulation, we propose to prepare ACM CAM, with basic amino acids (lysine, arginine and histidine) as co-formers, using a cryo-milling method. The solid-state behaviors of the ACM CAMs were characterized by polarizing light microscopy, differential scanning calorimetry and powder X-ray diffraction. Fourier transform infrared spectroscopy and molecular docking were carried out to understand the formation mechanism. Moreover, the gastro-protective effects of ACM CAMs were evaluated in a rat gastric ulcer model. The results demonstrated CAMs improved the dissolution rates of ACM compared with the neat amorphous counterpart. Furthermore, ACM CAMs are significantly effective in mitigating the ACM-induced gastric ulcer in rats, and the ulcer inhibition rates were almost 90%. More importantly, this study provided a useful method for mitigating drug-induced gastrointestinal damage and broadened the applications of drug-amino acid CAMs.

This study explores the potential of Eisenia fetida (Savigny) in vermicompost production within vermipits during winter months in the Rampur region of Uttar Pradesh, India. The vermipits were inoculated with 0.33 kg of E. fetida per pit, against the recommended rate of inoculation for assessment of real-time potential of earthworm on seasonal and regional grounds. The results revealed a significant increase in earthworm population, with three times production (4.1 kg) of the inoculated number (1.0 kg). The productivity dynamics of compost vs E. feida revealed a notable threefold and fourfold effectiveness, respectively. This dual advantage signifies the success of composting process, with the increased worm population indicating enhanced decomposition. The study attributes the combination of regional and edaphic factors viz., sandy loam soil with high humus content and good water passage, facilitating earthworm survival, reproduction and decomposition of agricultural waste. The loose and perforated soil structure allowed easy penetration of earthworms, transforming the soil into fertile compost. The research emphasizes the importance of soil moisture of semi-arid ecosystems thus highlighting the seasonal significance governing earthworm activity. The study provides insights into the mechanical ability of earthworms, its sensitivity to soil compaction and the influence of high hydration of the region. Inoculation during the winter period indicates increased earthworm activity setting the stage for enhanced compost production in the upcoming hot periods of summer months. The findings suggest that optimizing vermicomposting practices with altered feeding stocks, could further improvise compost and earthworm production and productivity in subsequent seasons. The study contributes for sustainable utilization of E. fetida in composting, its regional and seasonal efficacy turns trash to treasure for enhanced agricultural efficacy

Self-administered pre-participation screening for physical activity (PA) requires an instrument that should be easily used and identify individuals at high risk. The Physical Activity Readiness Questionnaire (PAR-Q+) has been used for many years. Its ease of use and ability to identify those not fit to undergo PA has not been assessed. This study was to determine the rates of the PAR-Q+ in identifying adults who may not be fit for moderate or intense PA and obtain feedback on the use of this tool. A public on-line voluntary survey on the PAR-Q+ was carried out obtaining participants’ bio-characteristics, them completing the PAR-Q+ form and providing feedback. With 1019 participants, about 57.8% engaged in at least 150 minutes of PA weekly. This decreased with increasing number of co-morbidities. Increasing age was associated with more co-morbidities. About 33.1% of the participants using the PARQ+ would have required further medical evaluation. Only 3 of the 7 main PAR-Q+ questions were easily understood. Difficulties were encountered with 39 of the 44 follow-up questions, especially amongst those with co-morbidities. The large number of technical terms was also a source of concern. The PAR-Q+ would need extensive simplification before it may be recommended for use.

The energy transition is a challenge that affects all sectors, from transport to civil structures and industry. With reference to the industrial sector, the greatest need is the decarbonisation of industries energy-intensive, such as producers of iron and steel, aluminium, cement, petrochemicals, paper, etc. In particular, the steel industry is a hard to abate high-emissivity industry which due to chemical processes and high thermal demands (often above 500 °C) contributed to 7.4% of global CO₂ in the year 2021. This paper has explored the potential applications of hydrogen in the hard-to-abate sectors, highlighting its versatility and significance in decarbonization efforts. It provides an overview of hydrogen production methods, emphasizing the importance of sustainable and green hydrogen production. It reviews hydrogen production methods, storage, and potential in blended combustion. In the final part of the article, some considerations are introduced on the possible role of hydrogen in the steel sector (both as a supplementary fuel and as a reducing agent in innovative processes), showing how although there is potential for its inclusion as an element for the decarbonization, it is necessary to evaluate the energy balances of the various processes and the methods of hydrogen production very carefully, in order not to risk obtaining a marginal effect.

This paper proposes a heuristic approach for managing complex construction projects. The tool incorporates with Primavera P6 EPPM and Synchro 4D, enabling proactively clash detection and resolution of spatial conflicts during concurrent tasks. Additionally, it performs resource verification for sufficient allocation before task initiation. This integrated approach facilitates the generation of conflict-free and feasible construction schedules. By adhering to project constraints and seamlessly integrating with existing industry tools, the proposed solution offers a comprehensive and robust approach for construction project management. This constitutes to our knowledge the first dynamic digital twin for the delivery of a complex project.

Reducing the carbon footprint of energy production is one of the most pressing challenges facing humanity today. Lignocellulosic biomass residues from fruit production industries show promise as a viable energy source. This paper presents a study of the Italian context concerning the utilization of orchard lignocellulosic residues for energy production as electricity or bioethanol. The potential of various orchard residues was assessed through chemical and physical analysis, and an equivalent electrical energy of about 6441.62 GWh or an amount of 0.48 Mt/y of bioethanol was obtained based on the average annual dry residue mass availability of about 3.04 Mt/y. These data represent the 9.30% of the national electrical energy production from renewable sources, as well as the 6.21% of the Italian demand for gasoline in 2022. Electricity generation from these residues shown its potential as a reliable and sustainable baseload power source, as well as source of renewable transportation fuel. The studied process could be a valuable reference to expand these concepts on global scale to achieve a greener and more sustainable energy future.

In an effectively managed grazing system, goats as grazers can benefit the land's physical, chemical, biological, and economic aspects. However, little research has evaluated rotational and continuous goat grazing in Kentucky. This observational study investigated the impact of rotational and continuous grazing on forage production and goat performance. One group of 10 does was placed on a rotational pasture, and another group of 10 does were placed on a continuous pasture, each pasture measuring two acres. The pastures were side-by-side with similar forage types and compositions. Goat performance was measured by body weight and eye color score (FAMCHA). Forage production was measured weekly by collecting forage heights at three random spots in each pasture. The rotational grazing field displayed a more evenly grazing pattern, while the continuous field experienced overgrazing in some areas and overgrown of the less desired forage. Goats on the continuous field had a decrease in body weight, while the weights were more consistent in the rotational grazing field. The FAMACHA score was temporarily reduced on the rotational grazing pasture, indicating that properly managed rotational grazing may prevent anemia, possibly by reducing the shedding of gastrointestinal parasites. However, due to drought and lack of forage, the FAMACHA score of goats in the rotational grazing system reverted to its original status by the end, indicating that more extensive management and timely adjustments are necessary to ensure optimal goat performance. Our results suggest that rotational grazing may support more consistent forage yields and body weights of goats and has the potential to reduce the incidence of anemia and parasitic infestations in goats in Kentucky.

Volunteering has many social, emotional and health benefits and could be an option for people with younger/early onset dementia to engage in stage/age-appropriate, personally meaningful activity within their local community. Audio data of people with young onset dementia discussing their volunteering experiences were taken from the Dementia Diaries and co-analysed. This study explored how people with dementia volunteer in the UK, the benefits and barriers, and how we can improve access to volunteering opportunities. The findings suggest that stigma is the overarching concept (or net) which influences people’s experiences of volunteering with dementia. Within the stigma net, three themes were developed that employed a lifespan approach to challenging said stigma: 1) Valuing the past, 2) Valuing the present and 3) Valuing the future, each with additional subthemes. This research contributes to the limited pool of literature that highlights the clear benefits of volunteering for people with young onset dementia, while also considering how dementia stigma can create practical and institutional barriers to accessing volunteering. Guidance is provided for how to deliver meaningful and accessible volunteering opportunities.

Driven by mounting environmental apprehensions stemming from the over dependence on fossil fuels in energy and transportation sectors, extensive exploration into alternative energy sources, particularly biomass, has stimulated profound research on harnessing the potential of computational and mathematical techniques. This comprehensive survey delves into optimal models and strategies, unveiling their pivotal role in the design of biomass gasification processes.of hydrogen through biomass gasification. In this study, we aim to provide a comprehensive overview of the computational and mathematical techniques employed in optimizing biomass gasification processes, with a specific focus on enhancing hydrogen yield. Through an extensive literature review, various models and strategies will be examined, including thermodynamic analysis, kinetic modeling, reactor design, and process optimization. By uncovering the power of these techniques, we aim to contribute to the advancement of sustainable and efficient biomass utilization for the hydrogen-based future economy.This paper aims to provide an updated and comprehensive coverage of the investigations conducted on the potential of producing hydrogen from biomass through gasification. To achieve this, we incorporate the latest works that have utilized numerical modeling, simulation, optimization techniques, process heat integration, and co-generation in their studies. By encompassing these aspects, we aim to offer a broader and more in-depth re-appraisal of the subject matter. This will ensure that readers gain a holistic understanding of the advances made in the field and the potential for sustainable hydrogen production of biomass gasification.Through a meticulous re-appraisal and analysis of each subject, we can identify their respective strengths and areas that require further research effort. By thoroughly examining numerical modeling, simulation, optimization techniques, process heat integration, and co-generation, we can assess their effectiveness and applicability in the context of biomass gasification for hydrogen production. This analysis shed light on the areas where these techniques excel, as well as pinpoint limitations or gaps in current understanding. By identifying these areas, we can highlight the need for further research and development, enabling us to make significant advancements in biomass gasification processes and pave the way for a sustainable and efficient hydrogen-based future economy..

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

The spanwise periodicity within the gap was observed in the literature, which should be systematically studied in order to ascertain its characteristics and its influences on flow field. By numerically simulating the flow around two tandem circular cylinders with a diameter ratio of d/D=0.6 and seventeen spacing ratios (L/D=1.00~6.00) at Re=3900, this study shows four flow regimes: Reattachment Flow (L/D=1.00~3.15), Bi-stable Flow (L/D=3.24), Intermittent Lock-in Co-shedding (L/D= 3.30~3.50) and Subharmonic Lock-in Co-shedding (L/D=4.00~6.00). Further, depending on the spanwise periodicity length of the time-averaged flow structures (i.e. Pz) within the gap, Reattachment Flow is, for the first time, subdivided into three new sub-flow regimes: Small-scale Periodic Reattachment (L/D=1.00~1.50, Pz/D=(0, 4]), Large-scale Periodic Reattachment (L/D=2.00~2.25, Pz/D>4) and Non-periodic Reattachment (L/D=2.50~3.15, no spanwise periodicity). The formation mechanisms are elaborated by analyzing the combined effect of both the L/D value and the spanwise-averaged time-averaged reattachment angle of the downstream cylinder. Moreover, this study proves that the newly-defined Small-scale Periodic Reattachment and Large-scale Periodic Reattachment are responsible for the pronounced asymmetry of the flow along the transverse direction within the gap. In addition, detailed flow properties and statistical parameters are provided for each flow regime, such as velocity, vorticity, force coefficient, separation/reattachment angle, Strouhal number and Q-criterion.

The sound power LW of wind turbines (WTs) over the past decades has developed in relation to their electric power P as LW ∝ logP. The spectral distribution of the sound did not change significantly over time. This applies to the average performance of wind turbines, with differences between individual WT types. Because of the expected growth of onshore wind energy, a greater number of people will be living close to wind farms. This sustains the need for sound reduction. Sound reduction measures, such as serrations, reduced tip speed and low noise modes, may counteract the development of higher sound power from ever bigger WTs. To investigate this, the sound production of WT types over the last decades is analysed in relation to their size and electric power and the application of sound reduction measures. The analysis includes the broad band A-weighted and low frequency sound power levels as well as more detailed spectral distributions. Results show that the sound power level of wind turbines above 3 MW on average increases less with size than smaller turbines did. This is due to a lower blade tip speed and the use of sound reducing serrations. The spectral content of wind turbine sound, including the lower frequencies, has not changed significantly.

The advent of social commerce (SC) has transformed the landscape of online consumer behavior, emphasizing the significance of customer-to-customer relations in shaping sustainable relation-ships with customers. This research investigated the intricate relationships between social com-merce dimensions, particularly suggestions and recommendations, forums and communities, and ratings and reviews, and their influence on customer-to-customer value co-creation (C2CVCC) and sustainable customer relationships (SCRs). A questionnaire was designed and administered to 635 respondents. We examined the psychometric properties of the measurements and subse-quently applied Partial Least Squares as a Structural Equation Modeling method (PLS-SEM) for hypothesis testing. The findings reveal that the dimensions of SC significantly impact C2CVCC, with ratings and reviews playing a pivotal role. Furthermore, C2CVCC emerges as a substantial mediator in the path between SC and SCRs. The empirical analysis showcases strong support for the proposed model, with robust path coefficients (β) and p-values confirming direct and indirect effects. These findings offer valuable insights for businesses seeking to leverage SC and customer interactions to enhance SCRs in the digital era. Understanding the dynamics of C2CVCC within the context of SC has become essential for marketers and businesses aiming to thrive in today's competitive online marketplace.

The COVID-19 pandemic remains a serious public health problem globally. During winter flu seasons, more aggressive SARS-CoV-2 infections with fatalities have been documented, indicating that influenza co-infections may significantly impact the disease outcome of COVID-19. Both influenza and SARS-CoV-2 viruses share many similarities in their transmission and cellular tropism for their replication in the human respiratory tract. However, it is still unclear how the two pathogens interplay to ensure their survival in the same lung microenvironment. In addition, clinical studies on influenza co-infections in COVID-19 patients do not provide conclusive evidence on how influenza co-infection mechanistically modifies the disease outcome in COVID-19. This mini-review discusses various viral as well as host factors that potentially influence the survival or synergism of these two respiratory pathogens in the infected lung microenvironment.

AbstraIncorporating knowledge of indigenous forage legumes or associated nutritional attributes in cultivated pastures has the potential to improve grazing conditions, rangeland conditions, and cattle productivity. Climate change and other site-specific factors such as land sizes and other grazing management practices play a significant role in food security, job creation, and environmental health. Several research results have reported that the utilization of forage legumes in most farming systems has proved to increase herbage yield and soil fertility. The major aim of this review is to elucidate the potential benefits of intercropping indigenous forage legumes such as cowpea (Vigna unguiculacta L.Walp) and Dolichols (Lablab purpureaus) intercropped with Chloris gayana, this is to assesses the principal advantages, productivity, and overall performance of forage legumes grown in conjunction with grasses. Moreover, this review seeks to provide insights into the optimal management practices for intercropping forage legumes with grasses. The promising feature of intercropping South African pastoral systems must target the ability of forage legumes in terms of performance and utilization of agro-symbiotic relationships of N2 fixation symbiotic relationship in pastures. Moreover, this review aims also to address this knowledge gap by assessing the effects of defoliation frequency on the biomass production of selected forage legumes when intercropped with Chloris gayana in different growing seasons. By examining how varying defoliation frequencies influence biomass production, this review aimed to provide practical recommendations for optimizing forage management practices and promoting sustainable forage production systems. Through this investigation, we can gain insights into the complex dynamics between the defoliation frequency, intercropping systems, and biomass production.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.

NUMMI was one of the most analyzed case studies in terms of joint ventures, management dysfunction, and international globalization. NUMMI is an acronym for New United Motor Manufacturing, Inc. This manufacturer was a joint venture between automotive US titan GM and Toyota of Japan. GM wanted to further monetize its Fremont factory, but also had limited opportunities during a US economical recession. Toyota wanted to expand manufacturing operations in the US for the very first time, creating an intriguing collaborative partnership between the two. However, various problems lead to dysfunction through cultural, organizational, or managerial differences. This case study is analyzed through its historical analogical scope, ultimately leading to hypothesizing remediation through an ethical data-driven and total quality management (TQM) approach.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

This research explores the behaviors of Generation Z consumers in China, particularly focusing on their interaction with companies through social media for the joint creation of value. Adopting a qualitative methodology, the research initially constructs a scale for assessing co-creation of value on social media platforms. Subsequently, it delves into the motivational aspects of users' engagement in these co-creative activities. The study unveils a range of utilitarian and hedonic motivations that drive Generation Z's value co-creation actions on social media. Insights derived from the findings offer both theoretical and practical implications for the field.

The objective of this study was to investigate age-related changes in cashmere production and the population of active secondary hair follicles in cashmere goats across different age groups, as well as to explore the association between secondary hair follicle activity and oxidative stress. A total of 104 adult Inner Mongolian ewe goats, aged between 2 and 7 years old, were randomly selected as experimental subjects. Skin samples were collected in August 2020 and cashmere samples were collected in April 2021. The cashmere fiber yield, staple length, and diameter showed age-related variations in cashmere goats aged 2 to 7 years (P < 0.05). Cashmere production was higher in goats aged 2-4 years compared to those aged 5-7 years (P < 0.05). There were no significant differences in the population of primary and secondary hair follicles among goats aged 2 to 7 years. However, the population of active secondary hair follicles varied significantly with age, with the younger group (aged 2-4 years) having a higher population than those aged 5 – 7 years (P < 0.05). A moderate negative correlation was observed between cashmere fiber diameter and the population of active secondary hair follicles (P < 0.05). Age-related variations in skin antioxidant capacity and oxidative damage were observed among cashmere goats aged 2 to 7 years old (P < 0.05). Goats aged 2 to 4 years exhibited higher antioxidant capacity and lower oxidative damage (P < 0.05). Interestingly, the skin antioxidant capacity and oxidative damage exhibited significant positive and negative correlations, respectively, with the population of active secondary hair follicles (P < 0.05). This study presents a novel approach to enhance the activity of secondary hair follicles and improve cashmere production performance through the regulation of oxidative stress.

Companies are increasingly focusing on sustainable business practices. Internal and external stakeholders’ expectations manifest in legal requirements, national and international standards, and market and customer expectations, among other things, must be considered. In addition to profit maximization as the usual target for corporate management, management must consider environmental sustainability aspects such as resource efficiency, greenhouse gas intensity, and a company's emissions behavior. In addition, social aspects relating to the company's employees, the immediate urban environment, the situation in the supply chain, and effects on the market environment must increasingly be considered. Specifically, companies are faced with the chal-lenge of dealing with conflicting objectives regarding the various aspects of sustainability and, if necessary, weighing them up against each other. These trade-offs must be made against the company's socio-economic and ecological environment, corporate strategy, and sustainability goals. This paper provides an overview of current approaches and research gaps on this topic through a literature review. It shows a lack of methods and frameworks to specifically deal with trade-offs and conflicts of goals.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Objective: The study aimed to characterize the changing landscape of circulating SARS-CoV-2 lineages in the local community of Hong Kong throughout 2022. We examined how adjustments to quarantine arrangements influenced the transmission pattern of Omicron variants in a city with relatively rigorous social distancing measures at that time. Methods: In 2022, a total of 4,684 local SARS-CoV-2 genomes were sequenced using the Oxford Nanopore GridION sequencer. SARS-CoV-2 consensus genomes were generated by MAFFT, and the maximum likelihood phylogeny of these genomes were determined using IQ-TREE. The dynamic changes in lineages were depicted in a time tree created by Nextstrain. Statistical analysis was conducted to assess the correlation between changes in the number of lineages and adjustments to quarantine arrangements. Results: By the end of 2022, a total of 83 SARS-CoV-2 lineages were identified in the community. The increase in the number of new lineages was significantly associated with the relaxation of quarantine arrangements (One-way ANOVA, F(5,47)=18.233, p&lt;0.001)). Over time, Omicron BA.5 sub-lineages replaced BA.2.2 and became the predominant Omicron variants in Hong Kong. The influx of new lineages reshaped the dynamics of Omicron variants in the community without fluctuating the death rate and hospitalization rate (One-way ANOVA, F(5,47)=2.037, p=0.091). Conclusion: The study revealed that even with an extended mandatory quarantine period for incoming travelers, it may not be feasible to completely prevent the introduction and subsequent community spread of highly contagious Omicron variants. Ongoing molecular surveillance of COVID-19 remains essential to monitor the emergence of new recombinant variants.

Viral co-infections, where a host is infected by multiple viruses simultaneously, are common in the human population. Human viral co-infections can lead to complex interactions between viruses and the host immune system, affecting the clinical outcome and posing challenges for treatment. Understanding the types, mechanisms, impacts, and identification methods of human viral co-infections is crucial for the prevention and control of viral diseases. In this review, we first introduce the significance of studying human viral co-infections and summarize the current research progress and gaps in this field. We then classify human viral co-infections into four types based on the pathogenic properties and species of the viruses involved. Next, we discuss the molecular mechanisms of viral co-infections, focusing on virus-virus interactions, host immune responses, and clinical manifestations. We also summarize the experimental and computational methods for identifying viral co-infections, emphasizing the latest advances in high-throughput sequencing and bioinformatics approaches. Finally, we highlight the challenges and future directions in human viral co-infection research, aiming to provide new insights and strategies for the prevention, control, diagnosis, and treatment of viral diseases. This review provides a comprehensive overview of the current knowledge and future perspectives on human viral co-infections, and underscores the need for interdisciplinary collaborations to address this complex and important topic.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

Earth’s climate cannot be ignored any longer. Policies are vital in order to mitigate the negative effects of climate change. The energy crisis created by the Russo-Ukrainian war and pandemic affected the EU and its member states. The focus is more than ever on its energy policies and independence. The EU revised the energy strategy in response to Russia’s blackmail, and it sped up all the processes for energetic independence from Russia. This benefited the climate change policies the most, as all the measures involved reducing energy consumption and increasing renewables, thus contributing to reducing greenhouse gas emissions. As a member state of the EU, Romania is committed to complying with EU regulations. With a high degree of energy independence compared with the other EU members, Romania plans to become a regional energy provider and modernize the energy infrastructure internally as a response to Russia’s unprovoked aggression. The measures that the EU and Romania implemented after the war started in 2022 have come to fruition, and the effects are becoming visible a year later. This study aims to study the energy strategy of Romania in correlation with the EU strategy in the turbulent period of pandemics and war between 2019 and 2023, with the latest available data.

Purpose: To evaluate the relationship between corneal nerve structure and function in a veteran population. Methods: 83 veterans (mean age: 55 ± 5 years) seen at the Miami Veterans Affairs (VA) eye clinic were included in the study. Each individual filled out questionnaires to evaluate ocular symptoms (5-Item Dry Eye Questionnaire, DEQ5, Ocular Surface Disease Index, OSDI) and ocular pain (Numerical Rating Scale, NRS, Neuropathic Pain Symptom Inventory modified for the Eye, NPSI-Eye). Individuals also underwent an ocular surface examination that captured functional nerve tests including corneal sensation, corneal staining, and Schirmer test for tear production. Corneal sub-basal nerve analysis was conducted using in vivo confocal microscopy (IVCM) images with corneal nerve density, length, area, width, and fractal dimension captured. IVCM and functional corneal metrics from the right eye were examined using correlational and linear regression analysis. Results: Most corneal structural metrics were not related to functional metrics, except for weak correlations between various IVCM metrics and tear production. In addition, corneal nerve fiber area was positively related to corneal sensation (r = 0.3, p = 0.01). On linear regression analyses, only corneal fractal dimension remained significantly related to tear production (β = -0.26, p = 0.02) and only corneal nerve fiber area remained significantly related to corneal sensation (β = 0.3, p = 0.01). Conclusions: Most corneal nerve structural metrics did not relate to functional metrics in our veteran population, apart from a few weak correlations between structural metrics and tear production. This highlights caution in using corneal nerve anatomy to predict corneal function.

Antioxidant, anti-inflammatory and chemo-preventive features have been reported for the carotenoid diatoxanthin. Diatoxanthin is only produced by a few groups of microalgae where it functions in photoprotection. Its large-scale production in microalgae is currently not feasible. In fact, rapid conversion into the inactive pigment diadinoxanthin is triggered when the cells are removed from the high-intensity light source, which will be the case during large-scale harvesting of microalgae biomass. Zeaxanthin epoxidase (ZEP) 2 and/or ZEP3 have been suggested to be responsible for the back-conversion of high-light accumulated diatoxanthin to diadinoxanthin in low light in diatoms. Using the CRISPR/Cas9 gene editing technology we knocked out the ZEP2 and ZEP3 genes in the already commercially used marine diatom Phaeodactylum tricornutum to investigate their role in the diadinoxanthin-diatoxanthin cycle, and to determine if one of the mutant strains could function as a diatoxanthin production line. Light shift experiments proved that ZEP3 encodes the enzyme converting diatoxanthin to diadinoxanthin in low light. Loss of ZEP3 caused the high-light accumulated diatoxanthin to be stable for several hours after the cultures had been returned to low light, suggesting that zep3 mutant strains could be suitable as commercial production lines of diatoxanthin.

Silver eel were sampled in 1981 and 1983 in River Brede, Denmark, with outlet to the North Sea. Yellow eel in River Køge-Lellinge, Denmark, with outlet to the Baltic Sea were sampled 1965-1968. Silver eel were aged by burning the otoliths. Silver male ages varied from 4 to 25 years, lengths 30.8 to 45.3 cm, and female silver eel varied from 7 to 25 years, lengths 42.3 to 77.3 cm. von Bertalanffy trajectories of length-at-age of male and female yellow eel were calculated in both rivers. Younger yellow eel had significantly higher annual growth rate compared to older age groups, and females grew significantly faster than males. Two models for natural mortality M were used to estimate number of glass eel needed to produce number of silver eel for each sex and silver age group. Annual silver eel production from River Brede Å was 49.2 kg ha-1, demanding 2,894 glass eel ha-1 and in River Køge-Lellinge, the silver eel production was 48.5 kg ha-1, demanding 5,570 glass eel ha-1. It was calculated that one (0.29 g) thousand glass eel contribute to 8.8 kg silver eel in River Køge-Lellinge, and 17.0 kg silver eel in River Brede. To fulfill the Danish EMP in rivers requires annual stocking of 33 tons or 9.4 million reared on-grown eel (3.5 g) to compensate for 183 tons lost silver eel.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

This study explores how young people’s mental health was affected by the COVID-19 pandemic using artwork and semi-structured interviews. This is important to understand so that policy and practice professionals can support those affected, prepare, and respond to future crises, and support young people who are isolated and restricted in other contexts. Co-designed participatory art workshops and interviews were conducted with 16–18-year-olds (N = 21) from the London-based Longitudinal cohort Study of Cognition, Adolescents and Mobile Phones (SCAMP). Artworks and interview transcripts were qualitatively co-analysed with young people. From interviews, six themes were identified: adaptation, restriction, change, challenges, overcoming adversity, and lockdown life. From artwork, four themes were identified; trapped, negative mental wellbeing, positive emotions, and technology. Everyday factors such as home environment, relationships, hobbies, habits, and education or work were key determinants of how challenged and restricted participants felt, and their capacity to overcome this. This implies that young people’s mental health services should collaborate with other sectors to address wider life determinants in a holistic way, and that clearer guidance and support in these areas could mitigate the negative mental health impacts of major environmental changes on young people.

Abstract: The study used whole-genome sequencing (WGS) and bioinformatics analysis for the genomic characterization of 60 isolates of Listeria monocytogenes isolated from cattle farms, cattle abattoirs, and retail outlets in Gauteng province, South Africa. The isolates' sequence types (STs), clonal complexes (CCs), and lineages were determined using in silico multilocus sequence typing (MLST). We used BLAST-based analyses to identify virulence and antimicrobial genes, plasmids, proviruses, and the CRISPR-Cas system. The study investigated any association of the detected genes to the origin in the beef production chain of the L. monocytogenes isolates. Overall, in 60 isolates of Listeria monocytogenes, there were 7 STs, 6 CCs, 44 putative virulence factors, 2 resistance genes, 1 plasmid with AMR genes and 3 with conjugative genes, 1 CRISPR gene, and all 60 isolates were positive for proviruses. Among the 7 STs detected, ST204 (46.7%) and ST2 (21.7%) were the most prominent, with ST frequency varying significantly (p&lt;0.001). The predominant CC detected were CC2 (21.7%) and CC204 (46.7%) in lineages I and II, respectively. Of the 44 virulence factors detected, 26 (across Listeria Pathogenicity Islands, LIPIs) were present in all the isolates. The difference in the detection frequency varied significantly (P&lt;0.001). The two AMR genes (fosX and vga(G)) detected were present in all 60 (100%) isolates of L. monocytogenes. The only plasmid, NF033156, was present in 3 (5%) isolates. A CRISPR-Cas system was detected in 6 (10%), and all the isolates carried proviruses. Significant differences were detected in the frequencies of STs and virulence factors regarding the source and sample type of the L. monocytogenes isolates. The presence of both fosX and vga(G) genes in all the isolates from the three industries (cattle farms, abattoirs, and retail outlets) can potentially cause therapeutic implications. Our study, which characterized L. monocytogenes recovered from the three levels in the beef production chain in the country, provides the first evidence of the distribution of the pathogen with potential food safety and therapeutic implications.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

The described data set contains features from the machine control of a five-axis milling machine. The features were recorded during thirteen series productions. Each series production includes a changeover process in which the machine was set up for the production of a different product. In addition to the timestamps and the twenty recorded features derived from Numerical Control (NC) control variables, the data set also contains labels for the different production phases. For this purpose, up to 23 phases were assigned, which are based on a generalized milling process. The data set consists of thirteen .csv files, each representing a series production. The data set was recorded in a production company in the contract manufacturing sector for components with real series orders in ongoing industrial production.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Three Seas Initiative (3SI) is still an underresearched area and is particularly important due to historical circumstances and economic backwardness. A study was carried out to assess the impact of renewable energy and production generated by the agricultural sector on CO2 emissions in 3SI countries between 2008 and 2020. The study used panel data analysis based on the two-step system generalised method of moments (GMM) and the Dumitrescu-Hurlin panel causality test. The results show that a 1% increase in the value-added generated by agriculture increases CO2 emissions in the countries studied by 0.11%. In contrast, a 1% increase in GDP leads to a 0.29% increase in CO2 emissions. Conversely, when renewable energy consumption increases by 1%, CO2 emissions fall by 0.25% in the countries studied. One way to reduce CO2 emissions from agricultural production in the short term is to increase the share of renewables, which, incidentally, is in line with EU action.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

In politics and society, organic farming is widely seen as the ideal way to address the many challenges facing agriculture and food security. In order to examine the extent to which this view is realistic, the impact of organic and conventional farming is compared on the basis of relevant criteria such as land requirements, greenhouse gas emissions, biodiversity, food quality, production and environmental costs, reduced meat consumption, the need for agricultural imports and the global expansion of arable land. Land is considered to be a central factor. Such a comprehensive analysis is necessary to assess the impact of different influencing factors and to provide important suggestions for targeted decision making. Although organic farming has a positive impact on land use in many ways, it quickly reaches its limits. The low yields and high production costs resulting from the limited choice of means of production make organic farming an unsuitable model for the future in a world with limited arable land, a high and growing demand for food, and low incomes for large sections of the population. It can, however, provide significant impetus and contribute important technological knowledge for the further development of agriculture as a whole to meet the complex objectives of sustainability, greenhouse gas mitigation, biodiversity and global food security by incorporating all available technologies. Based on this, a model for responsible, sustainable intensive agriculture is outlined and proposals for an eco-social framework to support this model are put forward.

This paper presents a groundbreaking approach to real-time image processing in electronic component assembly, enhancing quality control in manufacturing. By capturing images from pick and place machines between component pickup and mounting, defects are identified and addressed in-line, significantly reducing the likelihood of defective products. Leveraging fast network protocols like gRPC and orchestration with Kubernetes, along with C++ programming and TensorFlow, this method achieves an average turnaround time of less than 5 milliseconds. Tested on 20 live production machines, it ensures compliance with IPC-A-610, and IPC-STD-J-001 standards while optimizing production efficiency and reliability.

In this study, we investigated the features of co-infection with SARS-CoV-2 and nonpathogenic strain LEV8 of coxsackievirus A7 or enterovirus A71 for Vero E6 cells and Syrian hamsters. The investigation of co-infection with SARS-СoV-2 and LEV-8 or EV-A71 in the cell model was shown that a competitive inhibitory effect for these viruses were especially significant against SARS-CoV-2. Pre-infection with enteroviruses in animals caused more than a 100-fold decrease in the levels of SARS-CoV-2 virus replication in the respiratory tracts and more rapid clearance of the lower respiratory tract from infectious SARS-CoV-2. Co-infection with SARS-CoV-2 and LEV-8 or EV-A71 also reduced the severity of clinical manifestations of the SARS-CoV-2 infection for animals. Additionally, the histological data illustrated that co-infection with nonpathogenic coxsackievirus decreased the level of pathological changes by SARS-CoV-2 in the lungs. Research into the chemokine/cytokine profile demonstrated that the studied enteroviruses efficiently triggered this part of antiviral immune response, which can be associated with significant inhibition of SARS-CoV-2 infection. These results demonstrate that there exists a strong viral interference between the studied nonpathogenic strain of coxsackievirus A7 or enteroviruses A71 and SARS-CoV-2 pathogenic for humans in vitro and in vivo.

Yellow eels were sampled by electrofishing in 1979, 1980 and 1981 in Vester Vedsted Baeck, Denmark, stem 6 km, catchment 24 km², with outlet to the North Sea. Yellow eels were aged by burning the otoliths. The eels were not sexed, and they varied from 6.5 to 44 cm in length. The ages varied from 0+ to 10+ year. The annual growth rate ∆ varied from 3.4 cm for 0+ eel to 2.2 cm for 10+ eel with a mean of 3.1 cm. Body mass wet wt. was recalculated to Kcal energy, with an annual growth rate ∆ of 5.33 Kcal. In contrast to body mass, the annual growth rate ∆ in Kcal increased with age. Von Bertalanffy growth trajectory (cm) of length-at-age was calculated and L∞ = 118.4 cm. Annual natural mortality M was estimated, and M was significantly depending on body mass, i.e. high M and low body mass vs. low M at high body mass. The biological production was calculated to 13.5 g wet weight m^-2 year^-1. Total 780 eel stomachs were analyzed, of which 287 (37%) were empty. The weight of food content (2.1% of eel body mass) increased proportional with eel body mass. Chironomid larvae, Ephemeroptera nymph, Simulium larvae and Gammarus pulix were the dominating food taxa, followed by Trichoptera larvae. Size of prey were independent on length of eel.

Salidroside, a valuable phenylethanoid glycoside, is obtained from plants belonging to the Rhodiola genus, known for its diverse biological properties. At present, salidroside is still far from large-scale industrial production due to the lower titer and higher process cost. In this study, we constructed a biosynthetic pathway from L-tyrosine to salidroside in Saccharomyces cerevisiae. To increase sali-droside production, we for the first time constructed an in vivo UDP-glucose regeneration system that sucrose synthase GmSUS worked in conjunction with UDP-glucose transferase RrUGT33 to improve the UDP-glucose availability with inexpensive sucrose as the consumed substrate. Finally, the molar conversion rate of L-tyrosine could reach 95%. To further reduce the cost, co-culture with E. coli that synthesized L-tyrosine de novo resulted in an 81% reduction in the final substrate cost per 1 kg of salidroside compared to the initial cost. The final titer of salidroside obtained 3.8 g/L and was the highest titer achieved at the Shake-Flask-Level in the existing reports. And this marked the first successful synthesis of salidroside in an in situ enhanced UDP-glucose system using sucrose. This accomplishment laid a robust groundwork for further investigations into the synthesis of other notable glycosides and natural compounds.

This study presents the interaction with human host metabolism of SARS-CoV-2 ORF7b protein (43 aa), using a Protein-Protein-Interaction Networks analysis. After pruning, we selected from BioGRID the 51 most significant proteins among 2,753 proven interactions and 1,708 interactors, specific to ORF7b. We used these proteins as functional seeds and we got a significant network of 551 nodes via STRING. We performed topological analysis and calculated topological distributions by Cytoscape. Seven high ranked proteins as hub and seven as bottleneck following a hub-and-spoke network-architectural-model were found. Through this interaction model, we identified significant GO-processes (5,057 terms in 15 categories) induced in human metabolism by ORF7b. High statistical significance processes of dysregulated molecular cell mechanisms by the action of ORF7b were discovered. We detected disease-related human proteins and their involvement in metabolic roles, how they relate in a distorted way to signaling and/or functional systems, in particular intra- and inter-cellular signaling systems and the molecular mechanisms that supervise to programmed cell death, with mechanisms similar to that of cancer metastasis diffusion. A cluster analysis showed 10 compact and significant functional clusters, where two of them overlap in a Giant-Connected-Components core of 206 total nodes. These two clusters contain most of the high-rank nodes. ORF7b mainly acts through these two clusters, inducing most of the metabolic dysregulation. We conducted a co-regulation, transcriptional analysis by hub and bottleneck proteins. This analysis allowed us to define the transcription factors and miRNAs that control the high-ranking proteins and the dysregulated processes, within the limits of the poor knowledge that these sectors still impose.

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

The study focused on the technical and scale efficiency of smallholder pineapple farmers in the Central Region of Ghana. The input-oriented Data Envelopment Analysis (DEA) was used to estimate technical, pure and scale efficiencies of the smallholder pineapple farmers, of which a random sampling procedure was used to select 320 respondents. The study revealed that the farmers were technically inefficient with mean technical efficiency under Constant Returns to Scale (CRS), pure efficiency under Variable Returns to Scale (VRS) and the Scale Efficiency levels of 0.505, 0.641 and 0.772, respectively, due to farmers’ inability to exploit fully the available technology while experiencing evident post-harvest losses resulting from low adoption of post-harvest technologies. Such findings are meaningful and could help the farming communities and relevant policymakers to understand the issues in farming production and hence undertake necessary actions to potentially improve farmers’ technical and scale efficiencies in the study area.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

A comprehensive investigation was undertaken at Vytautas Magnus University Experimental Station, located at 54°52’50” N latitude and 23°49’41” E longitude on soil (Epieutric Endocalcaric Planosol – PLe-gln-w) since 1999, to understand the impacts of different agrotechnical measures on soil health and crop yield. Two primary factors were assessed. Factor A incorporated practices of straw removal versus straw chopping and spreading, while Factor B evaluated a spectrum of tillage techniques: conventional deep ploughing, shallow ploughing, ploughless tillage, single seedbed discing, and two no-tillage practices, one of which involved cover crops. Findings from this long-term study highlight the significant potential of specific farming systems in enhancing soil organic carbon. It has a positive effect on the release of CO2 emissions from the soil, thus promoting soil resilience and increasing plant productivity. These insights are paramount in devising sustainable agricultural strategies to counter the challenges of climate change on agroecosystems. This research showcases the profound effects of combining residue management and tillage practices, setting a novel standard for sustainable soil management of climatic uncertainties.

Zika virus (ZIKV) infection and pathogenesis are linked to the disruption of neurogenesis, congenital Zika syndrome and microcephaly by affecting neural progenitor cells. Nonstructural protein 5 (NS5) is the largest product encoded by ZIKV-RNA and is important for replication and immune evasion. Here, we studied the potential effects of NS5 on microtubules (MTs) and autophagy flux, together with the interplay of NS5 with histone deacetylase 6 (HDAC6). Fluorescence microscopy, biochemical cell-fractionation combined with the use of HDAC6 mutants, chemical inhibitors and RNA interference indicated that NS5 accumulates in nuclear structures and strongly promotes the acetylation of MTs that aberrantly reorganize in nested-like structures. Similarly, NS5 accumulates the p62 protein, an autophagic-flux marker. Therefore, NS5 alters events that are under the control of the autophagic tubulin-deacetylase HDAC6. HDAC6 appears to degrade NS5 by autophagy in a deacetylase- and BUZ domain-dependent manner and to control the cytoplasmic expression of NS5. Moreover, NS5 inhibits RNA-mediated RIG-I interferon (IFN) production, resulting in greater activity when autophagy is inhibited (i.e., effect correlated with NS5 stability). Therefore, it is conceivable that NS5 contributes to cell toxicity and pathogenesis, evading the IFN-immune response by overcoming HDAC6 functions. HDAC6 has emerged as an anti-ZIKV factor by targeting NS5.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

Chemical process control relies on a tightly controlled, narrow range of margins for critical variables, ensuring process stability and safeguarding equipment from potential accidents. The availability of historical process data is limited to a specific setpoint of operation. This challenge raises issues for process monitoring in predicting and adjusting to deviations outside of the range of operational parameters. Therefore, this paper proposes simulation-assisted deep transfer learning for predicting and optimizing the final purity and production capacity of the glycerin purification process. The proposed network is trained by the simulation domain to generate a base feature extractor, which is then fine-tuned using few-shot learning techniques on the target learner to extend the working domain of the model beyond the historical practice. The result shows that the proposed model improved prediction performance by 99% in predicting water content and 79.72% in glycerin prediction over the conventional deep learning model. Additionally, the implementation of the proposed model identified the production and product quality improvement for enhancing the glycerin purification process.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Access to urban green and blue spaces (UGBS) has been associated with positive effects on health and wellbeing; however, the past decades have seen a decline in quality and user satisfaction with UGBS. This reflects the mounting challenges that many UK cities face in providing appropriate public facilities alongside issues such as health inequalities, an ageing population, climate change, and loss of biodiversity. At present, little is known about the preferences of different population subgroups and, specifically, the UGBS they visit and the spaces they avoid. Using a public participatory geographic information system (PPGIS), the overall aim of the research presented here was to investigate the preferences of different population subgroups in urban areas, and the UGBS they visit, using Edinburgh, Scotland as a case study. We created a baseline visitor demographic profile for UGBS use, and highlighted how visitors perceive, physically access, use, and engage with UGBS. The results revealed considerable variation in UGBS preference: one person’s favourite UGBS may be one that someone else dislikes and avoids. It is clear that adapting UGBS to suit local communities should not be a ‘one-size-fits-all’ approach. The conflicting views and preferences of different groups of respondents point to the importance of developing policies and park management plans that can accommodate a variety of uses and experiential qualities within individual parks. PPGIS offers an ideal tool for achieving this

Combustion power plants emit carbon dioxide (CO₂), a major contributor to climate change. Direct emissions measurement is cost-prohibitive globally, while reporting varies in detail, recency, and granularity. To fill this gap and greatly increase the number of power plants worldwide with independent emissions monitoring, we developed and applied machine learning (ML) models using power plant plumes as proxy signals to estimate electric power generation and CO₂ emissions using Landsat 8, Sentinel-2, and PlanetScope imagery. Our ML models estimated power plant activity on each image snapshot, and then an aggregation model predicted plant utilization over a 30-day period. Lastly, emissions factors specific to region, fuel, and plant technology were used to convert estimated electricity generation to CO₂ emissions. Models were trained with reported hourly generation data in the US, Europe, and Australia and were validated with additional generation and emissions data from the US, Europe, Australia, Türkiye, and India. All results with sufficiently large sample sizes indicate that our models outperformed baseline approaches. In conducting external validation to compare modeled versus reported annual generation and emissions in the countries where available, we calculated the root mean square error overall for modeled countries with validation data as respectively 1.75 TWh (236 plants across 17 countries over 4 years) and 2.04 Mt CO₂ (207 plants across 17 countries over 4 years). Ultimately, we applied our ML method to plants that comprise 32% of global power plant CO₂ emissions averaged over 2015-2022. This dataset is the most comprehensive independent and free-of-cost global power plant point-source emissions monitoring system currently known to the authors and is publicly available at climatetrace.org to support global emissions reduction.

The relationship between DM yield/cutting and fermentable organic matter (FOM) content of tropical grasses was appropriately investigated to re-access optimal grass maturity to feed dairy cattle. Nine different grass species belonging to the genera: Brachiaria spp. (Mulato II, Ruzi), Panicum spp. (Guinea, Hamil, Mombasa, TD58), and Pennisetum spp. (King, Napier, VA06) were chemically analyzed and subjected to an in vitro gas production (IVGP) test. For 72 h, gas production (GP) was continuously recorded with fully automated equipment. A triphasic, nonlinear, regression procedure was applied to analyse GP profiles. Across all the grasses, it was found that the neutral detergent fiber (NDF) contents increased with increasing maturity of the grass while the CP contents decreased with increasing NDF contents. In all nine grasses, digestible organic matter (dOM) was significantly affected by the week of cutting but IVGP was similar between weeks of cutting in Ruzi, Hamil, Mombasa, and Napier grass. Except for Guinea grass, the lowest dOM values were found when the grasses were cut after ≥ 5 weeks of regrowth. Harvesting grass one or two weeks earlier than normal cutting time is a practically relevant intervention in in-creasing forage quality and productivity of dOM and fermentation potential.

Eco-agricultural technology is crucial to alleviating agricultural resource scarcity and environ-mental pressures. However, financial constraint affects its successful promotion. Digital finance has a significant impact on farmers, but existing research lacks an exploration of the impact of digital finance on farmers' adoption of eco-agricultural technology. This study focuses on Rice–Crayfish Co-cultivation Technology as an example. It utilizes survey data from 1,063 households in China. An Endogenous Switching Probit model is employed to solve self-selection bias. The results reveal several key findings. First, the average treatment effect on the treated is 51.5%. This indicates that if farmers who use digital finance were to stop using it, the probability of adopting rice–crayfish co-cultivation technology would decrease by 51.5%. Therefore, digital finance is beneficial for farmers in adopting this technology. Second, heterogeneity analysis reveals that digital finance has a greater promoting effect on older farmers, those with lower education levels, and higher proportions of agricultural income. This suggests a greater reliance on digital financial services among vulnerable groups. Third, digital finance promotes farmers' adoption of rice–crayfish co-cultivation technology by alleviating financial constraints, expanding information channels, and increasing social capital accumulation. Overall, the findings offer valuable insights for for-mulating supportive policies.

Carbapenem antibiotics are the drug of choice for treating multidrug-resistant bacterial infections. Metallo-beta-lactamases (MBLs) are carbapenemase capable of hydrolyzing nearly all therapeutically available beta-lactam antibiotics. Consequently, a need to assess the frequency and phenotypic resistance phenomena of two MBL genes in diarrheal and urinary tract infections (UTIs). Samples were collected through a cross-sectional study, with MBLs genes detected via PCR. Two hundred twenty eight diarrheal bacteria were isolated from 240 samples. The most predominant pathogens were Escherichia coli (32%) and Klebsiella spp. (7%). Phenotypic resistance to amoxicillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 50.4%, 65.6%, 66.8%, 80.5%, 54.4%, 41.6%, 25.7%, 41.2%, 37.2%, and 42.9%, respectively.  Total 142 UTI pathogens were obtained from 150 urine samples, with Klebsiella spp. (39%) and Escherichia coli (24%) are the major pathogens. Phenotypic resistance to amoxycillin-clavulanic acid, aztreonam, cefuroxime, cefixime, cefepime, imipenem, meropenem, gentamicin, netilmicin, and amikacin was 93.7%, 75.0%, 91.5%, 93.7%, 88.0%, 72.5%, 13.6%, 44.4%, 71.1%, and 43%, respectively.  Twenty four diarrheal isolates carried either blaNDM-1 or blaVIM genes; the overall MBL gene prevalence was 10.5%. Thirty six UTI pathogens carried either blaNDM-1 or blaVIM genes (25.4%). Seven isolates carried both blaNDM-1 and blaVIM genes.  MBL genes exhibited a strong association with phenotypic carbapenem and other beta-lactam antibiotic resistance. Resistance to carbapenems requires active surveillance and stewardship.

We introduce the linear subgroup of volume-preserving diffeomorphism as the underlying symmetry to construct an action within the effective field theory framework and the Schwinger-Keldish formalism. The formulated action is posited to effectively incorporate dissipative effects into the Navier-Stokes equations.

Abscisic acid (ABA) is a conserved “stress hormone” in unicellular organisms, plants and animals. In mammals, ABA and its receptors LANCL1 and LANCL2 stimulate insulin-independent cell glucose uptake and oxidative metabolism: overexpression of LANCL1/2 increases, and their si-lencing conversely reduces, mitochondrial number, respiration and proton gradient dissipation in muscle cells and in brown adipocytes. We hypothesized that the ABA/LANCL hor-mone/receptors system could be involved in thermogenesis. Heat production by LANCL1/2-overexpressing vs. double-silenced cells was compared in rat H9c2 cardiomyocytes with two different methods: differential temperature measurements using sensitive thermistor probes, and differential isothermal calorimetry. Results indicate that overexpressing cells generate an approx. double amount of thermal power compared with double-silenced cells, and that addition of ABA further doubles heat production in overexpressing cells. With the temperature probes, we find a time-scale of approx. 4 min for thermogenesis to “turn on” after nutrient addition. These results identify the ABA/LANCL hormone receptors system as a hitherto unknown regu-lator of cell thermogenesis. Pharmacologic means of increasing metabolic energy dissipation are considered a promising strategy to reduce oxidative stress and lipid accumulation at a cellular and organismic level: from this study, LANCL1-2 proteins emerge as targetable controllers of ther-mogenesis through their natural ligand ABA.

The mushroom industry generates large amounts of stems, a co-product with valuable sensory and health characteristics. This work aimed to study the influence of particle size (L — &gt;0.510 mm; LI — 0.510-0.315 mm; SI—0.315-0.180 mm; S — &lt;0.180 mm) and species in the characterization and antioxidant activity of flours from stems of Agaricus bisporus (ABSF) and Pleurotus ostreatus (POSF). ABSF was rich in protein (14 g/100 g), calcium (428.23-700.77 mg/100 g), and sorbitol (22.57-26.60 g/100 g), while POSF in β-glucans (36.62-40.34 g/100 g) and linoleic acid (20.57-39.86 g/100 g of lipid). Both species were flush in amino acids with umami flavor. The highest hydration properties and oil holding capacity were exhibited in the S size of both species. ABSF showed elevated values for emulsifying activity than POSF. ABSF-S recorded the heightened antioxidant capacity in vitro, in consonance with the total phenolic compounds (0.91 mg/g). However, this antioxidant assays in POSF presented a positive correlation with β-glucans content. According to these results, there could be several food applications for these co-products, such as emulsifier stabilizer, sweetener or fortifier in the development of functional food.

In recent years, machine learning (ML) techniques have emerged as an efficient and effective technology within the petroleum industry. This paper focuses on the current application of ML in enhanced oil recovery (EOR) through CO2 injection, which exhibits promising economic and environmental benefits of climate-change mitigation strategy. Our comprehensive review explores the diverse use cases of ML techniques in CO2-EOR, including aspects such as minimum miscible pressure (MMP) prediction, well location optimization, oil production and recovery factor prediction, multi-objective optimization, Pressure-Volume-Temperature (PVT) properties estimation, Water Alternating Gas (WAG) analysis, and CO2-foam EOR, from 101 reviewed papers. In this comprehensive review, we catalog relative information, including the input parameters, objectives, data sources, train/test/validate information, results, evaluation, and rating score for each area based on criteria such as data quality, ML building process, and analysis of results. We also briefly summarized the benefits and limitations of ML methods in petroleum industry applications. Our detailed and extensive study could serve as an invaluable reference for employing ML techniques in the petroleum industry. Based on the review, we found that ML techniques offer great potential in solving problems in the majority of CO2-EOR areas involving prediction and regression. With the generation of massive amounts of data in the everyday oil and gas industry, machine learning techniques can provide efficient and reliable preliminary results for the industry.

Rapid increase in urbanization and industrialization due to increase in human population has led to increase in global warming resulting to climate change that affects the ecosystem. Unusual natural disasters such as cyclones, storms, floods, weather fluctuations, rising seal levels, transitional ecosystems and coastal disruptions are major adverse effects of climate change. There are huge worrisome concerns and uncertainties about the future of the planet earth due to climate change caused by high carbon emissions. Global aggressive policies in control of Carbon-dioxide (CO2) emissions from several combustion mechanisms have paved way for alternative/ clean energy sources. Green hydrogen is a promising means of clean energy sources for commercial power generation stations and other crucial systems such as hydrogen fuel cell vehicles (HFCVs) , motors, drives, backup power for buildings, and also serving as a source of electrical energy for remote locations. The goal of this study is to review the current level of Sub-Saharan African nations’ preparedness to adopt green hydrogen as a way to mitigate local energy supply issues and strengthen their individual economies.

China's cotton production has shown a concentration to the advantageous regions in recent years. Based on the relevant data of cotton production in China, the study measures the cotton production agglomeration levels of 16 major cotton-producing provinces from 1978 to 2020, summarizes the spatiotemporal evolution characteristics of cotton production agglomeration, and analyzes the factors influencing cotton production agglomeration using spatial econometric models. The results indicate that: Firstly, since the opening-up and reform, China's cotton production agglomeration levels have shown an overall upward trend, exhibiting periodic dynamic changes over time, and the spatial pattern reveals a dynamic regional gradient. Secondly, there is spatial correlation among the production scales of cotton in different provinces, with a trend resembling a "U" shape, and the agglomeration form shows a low-level convergence. Thirdly, technological level, policies, substitute industrial products and foreign trade are identified as important factors. The cotton production in each province is spatially correlated through these factors, and there is also a presence of spillover effects. In conclusion, the government should prioritize considerations of various influencing factors to formulate tailored support policies, promote large-scale production to enhance technological levels, and focus on policies aimed at improving the quality of cotton.

Suspended and deposited sediments in streams can interfere with filter-feeding caddisfly larvae by reducing feeding sites and feeding efficiency, potentially lowering densities, growth rates, and secondary production of an important trout prey. We conducted field studies at multiple stream sites with differing suspended sediment loads, and a laboratory study conducted under controlled conditions, together designed to examine the role of suspended sediments in the population dynamics and behavior of Brachycentrus occidentalis (Trichoptera: Brachycentridae) larvae in a Minnesota, USA, trout stream. Stream sites that had elevated turbidities and suspended sediments also had significantly more fine bottom substrates and higher substrate embeddedness. In addition, Brachycentrus densities were reduced, growth rates were slower, secondary production was reduced, and overall benthic macroinvertebrate taxa richness was lowest at the site with the highest suspended sediment loading. Colder water temperatures at one site also influenced Brachycentrus production. In 24-hour laboratory studies conducted in recirculating aquaria, the feeding activities of Brachycentrus larvae were reduced and positioning altered under high turbidities (500 nephelometric turbidity units, NTU) relative to low turbidities (50 NTU or lower). High suspended sediment loads have adversely affected filter-feeding caddisfly larvae by embedding and burying preferred coarse feeding substrates, altering their feeding positions and movements during highest flows, and ultimately impacting densities, growth rates, and secondary production.

In this article, we present two topics related to mathematical economics. We offer an intriguing proposal for securing cost and production functions in the face of uncertainty and risk. We discuss the relationship between individual and social preferences. This is important because traditional revealed preference theory does not account for such factors.

Symmetry-breaking is a phenomenon that is observed in various contexts, from the early universe to complex organisms, and is considered a key puzzle in understanding the emergence of life. The presence of enantiomeric amino acids and proteins highlights its critical role. However, the origin of symmetry-breaking has yet to be comprehensively explained, particularly from an energetic standpoint. This article explores a novel approach by considering energy dissipation, specifically lost free energy, as a crucial factor in elucidating symmetry-breaking. Through a thorough thermodynamic analysis applicable to enantiomeric systems at various scales, from elementary particles to aggregated matter like crystals, we present experimental findings that establish a direct correlation between non-equilibrium free energy and energy dissipation during formation processes. Results emphasize the pivotal role of energy dissipation not only as an outcome but as the trigger for symmetry-breaking. This insight suggests that understanding the origins of complex systems, from cells to living beings and the universe itself, requires a lens focused on non-equilibrium processes, ultimately facilitating the formation of non-racemic systems.

Decarbonization of air mobility requires the decarbonization of its energy. While biofuels will play an important role, other low carbon energy carriers based on electricity are considered: battery electrification, liquid hydrogen (LH₂) or eFuel, a hydrogen-based energy carrier. Each energy carrier has its own conversion steps and losses and its own integration effects with the aircraft. These combinations lead to different energy requirements and must be understood to compare their cost and CO₂ emissions. Since they are all electricity-based, this study compares these energy carriers using the well to rotor methodology when applied to a standard Vertical Take-Off and Landing (VTOL) air mobility mission. This novel approach allows one to understand that the choice of the energy carrier dictates the propulsive system architecture, leading to integration effects with the aircraft which can significantly change the energy required, from 400 to 2665 kWh for the same mission. These deviations lead significant differences in CO₂ emissions and costs. Battery electrification is impacted by the battery manufacturing but has the lowest electricity consumption. It is an optimum solution but only until the battery weight can be lifted. In all scenarios eFuel is more efficient than LH₂. We conclude that carrying the most efficient molecule in an aircraft pays the extra energy cost spent on the ground. Finally, we found that for each of these energy carriers, it is the electricity carbon intensity and price which will dictate the cost and CO₂ emissions of an air mobility mission.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Bovine Dewclaw Dermatitis (BDCD) is a hoof disease characterized by inflammation of the second and fifth accessory digits and the skin in this region. This pathology is poorly described in the literature; however, it has recently been observed in beef cattle in the Amazon Biome, Brazil. The objective of this study was to identify the epidemiological factors associated with BDCD onset in cattle in the analyzed biome. Samples were collected from eight farms with extensive breeding systems located in Xinguara, Rondon do Pará, Curionópolis, and Ipixuna do Pará, in the state of Pará, Brazil. A total of 706 Nellore and Nellore crossbred with taurine bovine of both sexes were evaluated, with males aged between 2–4 years and a mean weight of 650 kg and females aged between 2–11 years and a mean weight of 400 kg. Distal extremities were inspected during cattle management, and in case of dewclaw lesions, a specific examination was carried out after proper restraint. Bovine were diagnosed with BDCD in all farms analyzed. Of the 706 cattle inspected, 49 (6.94%) showed BDCD, of which 19 (38.77%) were Nellore and 30 (61.22%) were crossbred. This was the first study to determine BDCD’s occurrence in extensive farming systems in the Amazon re-gion, also showing that pastures with large amounts of stumps and stones, the physical structure of pens, and trauma and injury incidence during animal management are the most important pre-disposing factors for the onset of BDCD.

Neurological involvement following COronaVIrus Disease 19 (COVID-19) is thought to have a neuroinflammatory etiology. Co-ultraPEALut (an antiinflammatory molecule) and luteolin (an antioxidant) yielded promising results as neuroinflammation antagonists. This study aimed at describing cognitive impairment in post-COVID patient treated with co-ultraPEALut. Montreal Cognitive Assessment (MoCA), Prospective-Retrospective Memory Questionnaire (PRMQ), Fatigue Severity Scale (FSS) and a subjective evaluation were administered at baseline and after 10 months. Co-ultraPEALut-treated patients were retrospectively compared with controls. 26 co-ultraPEALut-treated patients showed significant improvement in PRMQ (T0: 51.94±10.55, T1: 39.67±13.02, p

The last decade has witnessed rapid development of immersive virtual reality (IVR) and its application in various contexts. However, its application in supporting real-time virtual collaboration has been quite rare due to technical barriers and the lack of validated design principles. To address this research gap, this study designed and developed an IVR space to enable multi-user synchronous co-located collaboration. An evaluation study (N = 95) was conducted to explore its useful design considerations and the influencing factors for collaboration experience. The IVR space was enabled by the simultaneous localization and mapping (SLAM)-based inside-out tracking technique and was informed by four essential design considerations for promoting effective collaboration in IVR, namely, the role script, learning task, collaboration mechanism, and communication design. The study results revealed that students in general were satisfied with their collaboration experience in IVR, with social presence and collaboration competency as significant predictors of collective efficacy and social experience. Based on both quantitative and qualitative results, this study proposes four validated principles for designing effective IVR spaces to support synchronous co-located collaboration.

Over the last two decades, knowledge production, research and reconfiguration of universities have been understood as ways of giving new meanings to the university-society binomial. In this regard, humanities are the subject of multiple debates in the face of ideas about their impact in relation to the "other sciences". Based on these premises, this article sets out to explore possible meanings attributed by researchers to the concepts of commitment, mobilization and transfer of research in humanities in view of the debates on the university-society interaction and the third mission of the university (Alonso, Cuschnir and Napoli, 2021). The methodology used will address bibliographical analysis, theoretical background and statements from different institutions, as well as the analysis of material from four interviews. As a first instance, the preliminary results show that strengthening critical thinking as forms of commitment emerge as central senses, focusing on hungarian characteristics and productions in order to unravel the ways of understanding and imagining Eastern European reality. In this respect, the discussion of certain western knowledge is seen as a task associated with social commitment with public universities as a focus of resistance.

This review article aims to delve into several aspects of sweetpotatoes and their leaves, including their nutritional composition, health benefits, culinary uses, and potential future implications as a superfood. It suggests an in-depth exploration of sweet potatoes' history, status, and prospects, highlighting their significance and potential economic value. Sweetpotatoes, often referred to as a powerhouse of nutrients, have gained popularity recently due to their remarkable nutritional composition and versatile culinary uses. This starchy root vegetable comes from the Convolvulaceae family and is consumed worldwide, playing a significant role in diverse cultures and cuisines. Besides their vibrant colors ranging from orange to purple, sweetpotatoes offer many health benefits, making them an essential addition to a well-balanced diet. Its extraordinary nutritional profile and numerous health benefits make it a superfood. Incorporating it into the diet can improve digestion, strengthen immunity, and reduce the risk of chronic diseases. With their versatility in the kitchen, there is no deficiency of charming and healthy recipes to explore. So, make room for sweet potatoes on your plate and unlock their vast potential to enhance your overall health and well-being. Overall, the future of sweetpotatoes looks bright as research and innovation aim to improve their nutritional value, adapt them to changing climate conditions, develop new varieties and products, and promote sustainable production practices. These developments can contribute to food security, economic growth, and healthier diets. Future research should focus on nutritional composition, health benefits, sustainable farming practices, cultivar development, and industrial applications to ensure sustainable and efficient production. By prioritizing research in these areas, we can enhance the utilization of sweet potatoes in various fields and secure their future for the next century.

The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

The purpose of this study is to analyze how global research cooperation patterns in the secondary battery industry have changed over recent years and to identify the evolution in the focus of research. To this end, network analysis was performed using the nationality information of the authors of a 10-year multinational joint research paper related to lithium-ion batteries. Furthermore, keyword analysis and topic modeling were performed using the abstract data from the study. The results of this study confirm that some countries that are not well-known in the field, such as Australia, Spain, and France, showed high centrality, compared with the level of cooperation scale. Additionally, six research topics were identified. According to a comparison over the first half of the decade, no difference was observed in the appearance of keywords indicating high energy density and conductivity with lithium, a key mineral. Keyword distribution was high for topics like battery charging and discharging in the first half of the decade, and for next-generation battery materials, such as solid electrolytes, lithium metal anodes, and lithium-sulfur batteries in the second. These results provide insights into the establishment of R&D cooperation strategies by countries and pre-planning by companies in the battery industry.

Selection of the most suitable material is one of the key decisions to be taken at the design stage of a manufacturing process. Traditional approaches as Ashby maps based on material properties are widely used in the industry. However, in the production of multimaterial components, the criteria for the selection can include antagonistic approaches. The aim of this work is the implementation of a methodology based on the results of process simulations for several materials and classify them by applying an advanced data analytics method based on Machine Learning (ML), in this case the Support Vector Regression (SVR) and Multi-Criteria Decision Making (MCDM) methodolo-gies, in this case Multi-criteria Optimization and Compromise Solution (VIKOR) combined with Entropy weighting methods. In order to do this, a Finite Element Model (FEM) has been built to evaluate the extrusion force and the die wear in a multi-material co-extrusion process of bimetallic Ti6Al4V-AZ31B billets. After applying SVR and VIKOR combined with Entropy weighting methodologies, a comparison has been established based on the material selection and complexity of the methodology used, resulting that material chosen in both methodologies is very similar and MCDM method is easier to implement because there is no need of evaluate the error of the pre-diction model and the time for data preprocessing is less than the time needed in SVR.

Welcome to the world of bioethanol revolution, in response to the soaring global energy demand, the production of bioethanol has taken center stage, captivating the attention of governments, academia, and the private sector alike. Over the years, research in this field has witnessed exponential growth, paving the way for sustainable energy production. Ethanol, the front-runner in renewable energy, can be derived from a plethora of sources. In this abstract, we will explore the exciting advancements and emerging trends in the production of bioethanol, shedding light on the promising future of sustainable energy. Bioethanol production presents a cost-effective solution by utilizing the abundance of agricultural resources. These resources serve as the foundation for producing bioethanol from various biomass sources. In this context, we evaluate the raw materials used, including sucrose-based, starchy-based, and perennial grasses. By exploring these options, we can gain a comprehensive understanding of the diverse range of agricultural feedstocks that contribute to the production of bioethanol, this paper delves into the multiple processes involved in the production of bioethanol from agricultural base biomass, unveiling a range of possibilities for harnessing renewable energy. The key steps that were thoroughly examined include pretreatment, which encompasses both physical and chemical methods, hydrolysis, direct fermentation, and saccharification. These steps serve as crucial components in the overall bioethanol production process from agricultural base biomass. By understanding and optimizing each of these stages, we can unlock the full potential of sustainable energy generation. The paper goes beyond exploring the production processes and delves into the different generations of bioethanol, each with its unique components. Additionally, it provides a comprehensive overview of the composition of agricultural and forest residues, shedding light on their potential as valuable resources for bioethanol production. Moreover, it highlights the significance of the agricultural sector in Nigeria's economy, emphasizing the importance of energy for enhancing productivity and efficiency. The integration of bioethanol as an energy source has the potential to propel this sector forward, fostering sustainable development and contributing to the overall growth of the Nigerian economy. By harnessing the power of bioethanol, Nigeria can tap into its energy potential, promoting energy utilization and creating a positive impact on various industries.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The characteristics of excess aerobic granular sludge, related to its structure and chemical composition, limit the efficiency of anaerobic digestion. For this reason, pre-treatment methods and compositions with other organic substrates are used. The aim of the research was to determine the effects of co-digestion of pre-hydrodynamically cavitated aerobic granular sludge with waste fats on the efficiency of methane fermentation under mesophilic and thermophilic conditions. The addition of waste fats improved the C/N ratio and increased its value to 19. The greatest effects were observed in thermophilic anaerobic digestion at 55°C, where a 15% waste fat content in volatile soilds was ensured. This resulted in the production of 1278.2±40.2 mL/gVS biogas and 889.4±29.7 mL/gVS CH4. The CH4 content of the biogas was 69.6±1.3%. The increase in biogas and CH4 yield compared to pure AGS anaerobic digestion was 34.4% and 40.1%, respectively. An increase in the proportion of waste fats in the substrate had no significant effect on the efficiency of methane fermentation.

This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

In the face of 21st-century environmental challenges, including climate change, migration pressures, and waste disposal issues, certain healthcare sectors, notably dentistry, pose a significant global environmental footprint with concerns about carbon emissions and waste production. This scoping review delves into the paradox that healthcare, while dedicated to safeguarding health, inadvertently contributes to environmental degradation through waste accumulation and disposal. The analysis of relevant pertinent literature emphasizes the imperative for an environmentally sustainable approach to dental waste measurement, disposal methods, and comprehensive education for stakeholders. Aligned with the World Conference on Sustainable Development and the United Nations' 2030 Agenda, the study adhered to PRISMA-ScR scoping review guidelines and Institute of Medicine's recommendations. The study utilized Medline/PubMed and international organization websites for data retrieval, employing Boolean operator queries in Medline. A systematic literature analysis identified six cross-sectional studies (2004-2018) highlighting variations in dental waste composition due to the lack of standardized identification methods. This heterogeneity underscores the need for a proposed research model, emphasizing comprehensive methodologies and healthcare staff training in waste management. The study advocates for environmentally conscious dental practices, contributing to broader sustainable healthcare goals through sharing of a research protocol for dental solid waste management.

This work presents noble composites of AAILs@MCM-48 by functionalizing ordered mesopo-rous silicon MCM-48 with two amino acid-based ionic liquids (AAILs) ([Emim][Gly] and [Em-im][Ala]) to improve carbon capture and selectivity of CO2 over nitrogen. Thermogravimetric and XRD analyses of the composites show that the MCM-48 support's thermal and structural in-tegrity was preserved after the AAILs were encapsulated. An N2 adsorption-desorption study at 77 K also confirms AAIL encapsulation in the porous support. Under post-combustion flue gas conditions, both [Emim][Gly]@MCM-48 and [Emim][Ala]@MCM-48 demonstrated improved CO2 adsorption in comparison to unmodified MCM-48, with a CO2 partial pressure of around 0.15 bar. In terms of maximal CO₂ uptake, the 40wt%-[Emim][Gly] composite outperformed the others at 303K, with values of 0.74 and 0.82 mmol g-1, respectively, at 0.1 and 0.2 bar. These numbers show a 10x and 5x increase, respectively, as compared to the pure MCM-48 under iden-tical conditions. In addition, the selectivity of the composites was improved significantly, at 0.1 bar, the selectivity of composites containing 40wt% [Emim][Ala] increased to 17, compared to 2 for pristine MCM-48.

Providing simultaneously autotrophic and heterotrophic carbon sources is a promising strategy to overcome the limits of autotrophic syngas fermentations. D-xylose and L-arabinose are particularly interesting as they can be obtained by the hydrolysis of lignocellulosic biomass. The individual conversion of varying initial concentrations of these pentoses and D-fructose as reference was studied with C. autoethanogenum in fully-controlled stirred-tank reactors with a continuous syngas supply. All mixotrophic batch processes showed increased biomass and product formation compared to an autotrophic reference process. Simultaneous CO and D-xylose or L-arabinose conversion was observed in contrast to D-fructose. In the mixotrophic batch processes with Larabinose or D-xylose, the simultaneous CO and sugar conversion resulted in high final alcohol to acid ratios of up to 58 g g-1. L-arabinose was superior as a mixotrophic carbon source because biomass and alcohol concentrations (ethanol and 2,3-butanediol) were highest, and significant amounts of meso-2,3-butanediol (>1 g L-1) in addition to D-2,3-butanediol (>2 g L-1) were solely produced with L-arabinose. Furthermore, C. autoethanogenum could not produce meso-2,3 butanediol under purely heterotrophic conditions. The mixotrophic production of meso-2,3-butanediol from Larabinose and syngas, both available from residual lignocellulosic biomass, is very promising for use as a monomer for bio-based polyurethanes or as an antiseptic agent.

When it comes to financial transactions and counterfeit detection systems, banknote classification is crucial. In this paper, we propose an approach for the classification of Kazakhstan banknote images integrating Learning Vector Quantization (LVQ) with Statistical Texture Feature Extraction using the Gray Level Co-occurrence matrix (GLCM). Our methodology demonstrates effectiveness in accurately classifying banknote images, as evidenced by experimental results. The comprehensive testing scenarios show promising outcomes, with the combination of GLCM and Color Histogram under the LVQ algorithm achieving a high accuracy of 94.87 percent at distance 1 and 90°. These findings indicate the robustness and practical viability of the proposed method for authenticating banknotes.

Type 2 Diabetes Mellitus (T2DM) is one of the most common metabolic disorders, with a major involvement of oxidative stress in its onset and progression. Pioglitazone (Pio) is an antidiabetic drug which primarily works by reducing insulin resistance while Curcumin (Cur) is powerful antioxidant with o important hypoglycemic effect, also. The both drugs are associated with several drawbacks, such as reduced bioavailability, a short half-life time (Pio) as well as instability and poor water solubility (Cur), which limit their therapeutic use. In order to overcome these disadvantages, a new co-delivery (Pio, Cur) nanosystem based chitosan (CS) (CS-Pio-Cur NPs), was developed, and characterized in reference with simple nanosystems (CS-Pio NPs, CS-Cur NPs). The developed CS-based NPs (CS-Pio-Cur NPs, CS-Pio NPs, CS-Cur NPs) were physico-chemical characterized in terms of particle size (PS), entrapment efficiency (EF%) and loading capacity (LC%). The CS-Pio-Cur NPs proved increased or similar values of EE (88.95% ± 7.79 for Cur; 94.83% ± 9.89 for Pio) and LC% (24.25 % ± 1.62 for Cur; 3.5% ± 0.98 for Pio), in reference with simple nanosystems, CS-Cur NPs (EE = 82.46% ± 1.74; LC = 20.34% ± 0.94) and CS-Pio NPs) (EE = 96.31% ± 0.68; LC = 4.11% ± 0.47), respectively. The identification of APIs (Cur, Pio) loaded into CS matrix was performed using FR-IR spectroscopy and for simultaneously quantification of APIs (Cur, Pio) released from CS-Pio-Cur NPs, a HLPC method was developed and validated. Based on release study performed in different simulated fluids (SGF, SIF, SCF) it can be appreciated that developed CS-APIs NPs have favorable pharmacokinetic profile with good release in gastrointestinal tract.

Integrating sustainable processes and innovative waste utilization not only addresses environ-mental challenges but also aligns with evaluating energy sustainability and creating the circular waste management. This study presents a comparative analysis of liquid fuel production from waste tires and water hyacinth using two thermochemical methods: co-pyrolysis (direct method) and co-gasification integrated with the Fischer-Tropsch (FT) process (indirect method). The As-pen Plus simulation software version 9 is employed to develop models, determining optimal operating conditions for maximum liquid fuel, and assessing economic viability. Co-pyrolysis simulations reveal an increase in oil products and a decrease in gas products with higher blending weight ratios of waste tires/water hyacinth (W/B) and lower pyrolyser temperatures. Operating at 400°C with a blending weight ratio of 75:25 provided the maximum liquid fuel rate of 6649.22 gal/day. For co-gasification, optimal conditions (W/B = 50:50, T = 800°C, steam to feed ratio (S/F) = 1) result in the highest syngas yield of 115.92 kmol/h. Fischer-Tropsch simulations demonstrate an increase in gasoline and a decrease in diesel with rising reactor temperatures. At 230°C, the maximum liquid fuel rate reaches 8817.15 gal/day. The economic and production yield analysis indicates that the indirect method better than the direct method, providing higher liquid fuel yields and investment worthiness.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.