For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

Human papillomavirus (HPV) infections, primarily transmitted through sexual contact, have been linked to various cancers, including cervical, penile, anal, oropharynx, breast, and prostate cancers. This study presents a unique case of concurrent high-risk HPV35, HPV45, and HPV59 infections in both prostate and bladder cancer tissues from a single patient, representing the first documented instance worldwide with identical HPV types detected in two adjacent organs of the same individual. Employing a multiplex-PCR approach, gel electrophoresis, and Sanger sequencing, we confirmed the presence of these high-risk HPV types. Additionally, Western blot analysis using an HPV E7 antibody demonstrated the active expression of HPV oncoproteins in both cancer types. This discovery underscores the potential for HPV intra-organ transmission and necessitates further exploration of alternative transmission routes. The implications of our results offer new insights into the complex dynamics of HPV transmission in cancer pathogenesis.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

The effects of chemical composition and solidification rate on the solidification behavior of high-Cr white irons were investigated through directional solidification. Increasing the solidi-fication rate in hypoeutectic alloys caused the finer dendrite arm spacing as expected. The eutec-tic structure which formed in the interdendritic region comprised of M7C3 and austenite, how-ever, secondary dendrite arms of hypoeutectic alloys contained a few M7C3 particles that solidi-fied prior to the eutectic structure. The transition from cellular to dendritic solidification oc-curred at a solidification rate between 50 µm/s and 100 µm/s in a near eutectic alloy. In the near eutectic alloy with cellular solidification, a directionally arrayed in-situ composite of M7C3/austenite formed within the cell. Speckle-like feature appeared in the intercellular region due to M23C6 carbide precipitation during subsequent cooling after freezing. Like dendrite arm spacing in hypoeutectic alloys, the inter-speckle spacing and the inter-fibre spacing became finer with increasing solidification rate in the cellular solidification range.

The performance analysis of the internal/external flows around a high speed vehicle in near-space is fundamental and critical to the configuration and structure design for high speed aircraft. In this paper, the two-dimensional coupled implicit Reynolds Average Navier-Stokes (RANS) solver and RNG k–ε turbulence model is employed to numerically simulate the flow field of an integrated high speed vehicle. The flow field are divided three parts to solve separately and compared with that solved by integrated simulation. The flow field are decomposed to save computer storage and simulation time. The first part is inlet/isolator, the second part is combustion chamber and the third is nozzle. In the computation process, the outlet condition of isolator is endowed to the inlet boundary of combustion chamber and the outlet boundary of combustion chamber is endowed to the inlet boundary of nozzle, then the whole flow field of integrated high speed vehicle is solved. Aerodynamic characteristic of fragment-computation and integration-computation is comparatively analyzed at different angles of attack, the results show that the maximum deviation of lift coefficient obtained by fragment-computation is less than 3% compared with that by integration, the maximum deviation of drag coefficient fragment-computation is less than 5% compared with that by integration, while pitching moment coefficient deviation less than 12%. However, for simulation time-consumption, the time used by fragment-computation reduces 45% compared with integration-computation. Meanwhile, by components force analysis, it can be concluded that the aerodynamic property of inlet/isolator can been obtained separately and hardly effected by other parts.

Infrastructure and urban network operators, city users and industrialists are faced with complex issues to ensure the sustainability of the service, maintain, operate and develop their urban sys-tems, while integrating environmental, economic and societal impacts and being resilient to un-expected geopolitical and climatic upheavals. Urban Digital Twins (UDTs), i.e., digital twins for smart cities and territories are considered as promising tools that can enable all stakeholders to collaborate across disciplinary silos and foster digital transformation in urban and territorial pro-jects to ensure sustainability, resilience and increased inventiveness. However, a widely acknowledged challenge to address in the application of UDTs is the lack of interoperability. One significant barrier is the difficulty that stakeholders have in understanding the level of complexity hidden behind this challenge, and thus the adoption of an adequate interoperability technique. This paper proposes a conceptual framework, which is unique for understanding the various lev-els of interoperability required in deploying and using the full potentials of UDTs. We show how such a high-level modeling approach supports the symbolic manipulation of UDTs interoperabil-ity notions and requirements, and thus eases the design of appropriate solutions for large-scale in-teroperable UDTs.

Purposes: Engaging in regular physical activity has been consistently linked to improved physical health and academic performance. Despite its known benefits, there is a concerning trend of decreased physical activity among children globally. The study primarily aims to investigate the level of physical activity among junior high school students in Taiyuan and analyze the main affecting factors from a socio-ecological perspective. Methods: A cross-sectional study was conducted, involving 650 junior high school students from 7 schools in Taiyuan, and 648 valid questionnaires were collected. Physical activity levels were assessed using the Children’s Leisure Activities Study Survey Questionnaire. Factors influencing physical activity were evaluated through the Student Perceived Factors Affecting Physical Activity Questionnaire. Results: In this study, students from the 7th, 8th, and 9th grades participated in physical activities, averaging 214.5 minutes per week in moderate-intensity and 25 minutes in high-intensity activities, cumulatively averaging 280 minutes weekly. Notably, a significant disparity (p<0.05) was observed in the combined duration of moderate and high-intensity activities, with male students engaging more time compared to their female counterparts (307.500 vs 255.000 minutes). This variance extended across different grades, particularly evident in 8th graders who recorded the highest weekly high-intensity activity duration (31.000 minutes) and overall physical activity time (320.500 minutes), surpassing the 7th graders. Furthermore, an exploratory factor analysis of a 32-item questionnaire, designed to identify determinants of physical activity, revealed six principal components. These components were found to positively correlate with both moderate and high-intensity physical activities. Conclusion: This study emphasizes the necessity for educational institutions and community programmes to provide engaging physical activities, especially during weekends. It highlights the importance of tailoring physical education curricula to address gender and grade differences and investing in quality sports equipment and facilities by schools and local governments.

Helicobacter Pylori (H. Pylori) is a common pathogen with high prevalence of infection in human populations. Diagnosis of H. Pylori infection is critical for its treatment, eradication, and prognosis. Biosensors have been demonstrated to be powerful for rapid onsite detection of pathogens, particularly for point-of-care test (POCT) scenarios. In this work, we propose a novel optical biosensor, based on nanomaterial porous silicon (PSi) and photonic surface state Tamm Plasmon Polariton (TPP), for detection of cytotoxin-associated antigen A (CagA) antigen of H. Pylori bacterium. We fabricated the PSi TPP biosensor, analysed its optical characteristics and demonstrated through experiments towards sensing of CagA antigen, that TPP biosensor has sensitivity of 100 pm/(ng/ml), limit of detection of 0.01 ng/ml, and specificity in terms of positive-to-negative ratio of more than six. From these performance factors, it can be concluded that TPP biosensor can serve as an effective tool for diagnosis of H. Pylori infection, either in analytical labs or in POCT applications.

: Cardiac surgery (CS) with extracorporeal circulation (ECC), induces oxidative stress and systemic inflammatory response, which may seriously affect postoperative lung function. We aimed to test if high parenteral (200mg/kg/24h) perioperative (48h) doses of Vitamin C (VitC) may reduce the incidence and severity of postoperative pulmonary complications (PPC) in selected CS patients. Single centered, prospective, randomized, single-blinded, interventional study included 150 patients, assigned to control group A (n=75) and interventional group B (n=75). Group B intraoperatively received 1/4 of the planned daily Vit C dose (200mg/kg/24h), diluted in 10 ml of normal saline, divided into three parts, while Group A received an equal volume of normal saline at the same time frames. After 6 h from the first intraoperative dose, the following regimen was applied: Group B: 200 mg/kg/24h - 30 min i.v. infusion of VitC in 50 ml of normal saline, every 6h, for the next 48h, and Group A: 30 min i.v. infusion of an equal volume of normal saline every 6 hours, for the next 48h. Modified Kroenke’s score was used to determine the incidence and severity of PPC. The overall incidence of PPC was 36.7% and was significantly lower in Group B (13.3% v.s. 60.0%, p&lt;0.001). The severity of PPC was also significantly lower in Group B [1(1) v.s. 3(2), p&lt;0.001]. Besides, patients from Group B had significantly less damaged lungs and better postoperative renal function, shorter ICU stay, fewer ICU re-admissions, and lower hospital mortality. High parenteral daily VitC doses (200mg/kg/24h) given to selected CS patients for 48h after CS are safe and effective in reducing the incidence and severity of PPC. Further multicenter RCT is needed to confirm these results.

This research delved into exploring the impact of ladder training on improving the athletic performance of adolescent students, particularly focusing on boosting explosive power and speed. The study involved thirty boys aged 15-17, selected randomly from an Indian school in Doha, Qatar. The variables measured were Explosive Power (EP) and speed (S). EP was assessed using the Standing Broad Jump (SBJ), while Speed (S) was gauged through the 50-yard dash. Divided into two groups - the Experimental Group (EG) and the Control Group (CG), each consisting of fifteen students - the EG underwent dedicated ladder training for 12 weeks while the CG continued their routine. Analysis of pre-test and post-test results indicated significant enhancements in EP and speed within the EG, with notable shifts from 2.15±.27 to 2.40±.24and 7.52±.54to 6.97±.66, respectively, exhibiting significant 't' values (EP: -2.39; speed: 2.23) at P˂.05. Conversely, the CG showed minimal changes in EP (pre: 2.22±.22; post: 2.2±.21) and speed (pre: 7.51±.43; post: 7.58±.72), with 't' values of 0.295 and 0.842, respectively, failing to reach significance at P˂.05. These outcomes highlight the efficacy of ladder training in improving explosive power and speed among adolescent students, suggesting its potential as a safe and advantageous component in athletic training programs.

This paper discusses how mathematical models are used to predict environmental conditions. While these models are successful for larger scale phenomena, it becomes more complex for local weather or wave processes. Several approaches have been proposed to address this problem, including neural networks and statistical and mathematical models. The novelty in this approach is the use of statistical manifolds, which provide a more accurate way to estimate distances and cost functions. This work focuses on advancements in differential and information geometry for creating different types of models that can be used for environmental simulation and forecasting. These fields are vital for many institutes and centres worldwide, as they help solve challenges in areas such as meteorology, renewable energy, and aviation safety. Some potential IG applications to advance energy were given. Closing remarks with new open problems combined with the next research phase are provided.

Keywords: Wheat; Speed Breeding; Maize Pollen Induction; Chromosome Elimination; Doubled Haploid (DH)

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

BKW is a highly efficient Storage Function-type rainfall-runoff model that utilizes the steady-state storage (S) and outflow (Q) of a catchment at different rainfall intensities as the S-Q relation of the catchment. For the inundation nowcasting of urban areas under high-intensity, short-duration rainfall, a Storage Function-type model is a judicious choice. However, S-Q hysteresis exists in the catchment S-Q relation, and BKW is unable to exhibit hysteresis due to assuming that the S-Q relation of a catchment is a nonlinear relation. The S-Q hysteresis can influence the outflow estimation of BKW, reducing the model's accuracy. Through the evaluation of analytical solutions, we found that the change in rainfall intensity dominates the S-Q relation of a catchment. The S-Q relation during a rainfall event is a dynamic process rather than a monotonic nonlinear relation. By applying the dynamic S-Q relation in BKW, we improved BKW to become a highly efficient and accurate rainfall-runoff model for small urban catchments.

The high-quality development of urban-rural integration is a vital component of China's economy, serving as a strategic response to the in-depth deployment of new urbanization and rural revitalization strategies. This integration is underscored by the promotion of entrepreneurship in agriculture, rural areas, and among farmers, which acts as a driver for fostering high-quality development in urban-rural areas through market competition. The resulting influx of resources and commodities with similar characteristics plays a crucial role in bridging the urban-rural divide. To maintain objectivity, it is important to adopt a balanced approach and refrain from using biased language. This study delves into the connotation and internal mechanism of the high-quality development of urban-rural integration, centering on the principle of 'quality'. Specifically, it examines the role of entrepreneurship in agriculture, rural areas, and among farmers, and evaluates its direct impact and transmission mechanism. The research employs balanced panel data from 41 cities in the Yangtze River Delta region spanning from 2003 to 2021. The findings reveal that entrepreneurship in agriculture, rural areas, and among farmers serves as a catalyst for promoting high-quality urban-rural development through the construction of a virtuous cycle, whereby resource factors and commodity services are exchanged. Moreover, this deep integration yields diverse effects across economic, spatial, demographic, social, and ecological domains, underscoring the necessity of continued support for entrepreneurship in agriculture, rural areas, and among farmers to facilitate a seamless urban-rural economic cycle and fully realize the benefits of high-quality development.

Organic light-emitting diodes (OLEDs) have garnered considerable attention in academic and industrial circles due to their potential applications in flat panel displays and solid-state lighting technologies, leveraging the advantages offered by organic electroactive derivatives over their inorganic counterparts. The thin and flexible design of OLEDs enables the development of innovative lighting solutions, facilitating the creation of customizable and contoured lighting panels. Among the diverse electroactive components employed in the molecular design of OLED materials, the benzophenone core has attracted much attention as fragment for synthesis of organic semiconductors. On the other hand, the benzophenone also functions as a classical phosphor with high intersystem crossing efficiency. This characteristic makes it as compelling candidate for effective reverse intersystem crossing, potentially leading to the development of thermally activated delayed fluorescent (TADF) emitters. These emitting materials witnessed a pronounced interest in recent years due to their incorporation in metal-free electroactive frameworks and the capability to convert triplet excitons into emissive singlet excitons through reverse intersystem crossing (RISC), consequently achieving exceptionally high external quantum efficiencies (EQEs). This review article comprehensively overviews the synthetic pathways, thermal characteristics, electrochemical behaviour and photo-physical properties of the derivatives based on benzophenone. Furthermore, we explore their applications in OLED devices, both as host materials and emitters, shedding light on the promising opportunities that benzophenone-based compounds present in advancing OLED technology.

The altitude of the habitat is one of the important regulators of species survival. Kaçkar Mountains National Park is located in the Eastern Black Sea region of Turkey. This is the first study on the benthic diatom flora of the high mountain lakes in Kaçkar Mountains National Park, which is situated between 2782 and 3075 m a.s.l. A total of 84 diatom species were identified from benthic communities of 15 habitats in summer (19 July, 28 August) and autumn (10 September) months of 2020. The genus Pinnularia (13 species) formed the basis of the taxonomic list followed by Eunotia (5 species), Navicula (5 species), and Frustulia (4 species) genera, respectively. The waters in all the studied lakes were fresh, low-saline, with low-alkaline or circumneutral pH and organically uncontaminated as evidenced by prevailed bioindicator groups. Statistical methods and comparative floristic results confirm the role of the lake altitude for the diatom species distribution. Species richness was higher in lakes with lower altitude, but a statistical approach also revealed a tendency for it to increase with altitude if species richness increased. Further studies will be needed to continue exploring this pattern. In the first round of analysis, diatom species groups were categorized according to IUCN categories, revealing one potentially threatened and one rare species. To protect studied high mountain lakes, their ecological conditions must be constantly monitored in the Kaçkar Mountains National Park.

Background: Restorative materials might significantly affect load transmission at peri-implant bone. The aim of the present study is to evaluate the shock absorption capacity of two different polymeric materials to be used as frameworks for implant-supported prostheses. Methods: A masticatory robot was used to compare the shock absorption capacity of polyether-ketoneketone (PEKK) Pekkton®ivory (Cendres+Mètaux) and glass fiber-reinforced composite (GFRC) TRINIATM (Bicon). Five identical sample crowns for each of the materials was tested un-der the same conditions described in previously published papers (Menini et al. 2013). Forces transmitted at the simulated periimplant bone were recorded and statistically analysed. Results: The statistical analysis of forces transmitted at the simulated dental implant revealed significant differences between all the materials tested and significant differences with the mate-rials tested in a previously published paper (Menini et al. 2013: zirconia, glass ceramic, composite resin, acrylic resin). Only differences between PEKK and veneered PEKK and between PEKK and one of the previously tested composite resins were not statistically significant. PEKK samples demonstrated significantly greater shock absorption capacity compared to GFRC. Conclusions: PEKK revealed optimal shock absorption capacity. Further studies are needed to evaluate its efficacy in case of long span prostheses with reduced prosthetic volume.

Two novel members of the subfamily Betarhabdovirinae, family Rhabdoviridae, were identified in Brazil. Overall, their genomes have the typical organization 3’-N-P-P3-M-G-L-5’ observed in mono-segmented plant-infecting rhabdoviruses. In aristolochia-associated cytorhabdovirus (AaCV), found in the liana aristolochia (Aristolochia gibertii Hook), an additional short orphan ORF encoding a transmembrane helix was detected between P3 and M. AaCV genome and deduced encoded proteins share the highest identity values, consistently < 60%, with their counterparts of yerba mate chlorosis-associated virus (Cytorhabdovirus flaviyerbamate). The second virus, false jalap virus (FaJV), was detected in the herbaceous plant false jalap (Mirabilis jalapa L.) and represents together with tomato betanucleorhabdovirus 2, originally found in tomato plants in Slovenia, a tentative new species of the genus Betanucleorhabdovirus. FaJV particles accumulate in the peri-nuclear space, and electron-lucent viroplasms were observed in the nuclei of the infected cells. Notably, distinct from typical rhabdoviruses, most virions of AaCV were observed to be non-enclosed within membrane-bounded cavities. Instead, they were frequently seen in close association with surfaces of mitochondria or peroxisomes. Unlike FaJV, AaCV was successfully graft-transmitted to healthy plants of three species of the genus Aristolochia, while mechanical and seed transmission proved unsuccessful for both viruses. Data suggest that these viruses belong to two new tentative species within the subfamily Betarhabdovirinae.

High gravity brewing (HGB) and adjunct use are common practices in industrial breweries. This work studied the impact of HGB and wheat adjuncts on beer characteristics. Parameters were evaluated in full-malt beer and beers prepared with 30 % wheat grits (WG) and wheat flakes (WF) in the grist and the effect of HGB was examined. Five beers were prepared; one control, two with different original gravity (OG) with WF and two with WG. Beers with higher OG were diluted to a lower OG and control beer was prepared too. The application of wheat adjuncts increased foam stability but HGB did not affect the beer foam. HGB beers had a remarkably higher ester concentration than other samples, and beers with WG also had a significantly higher ester content. Decreased higher alcohols to esters ratio in HGB beers affected the balanced flavour profile of the lager beer. There was a significantly lower content of unwanted volatiles such as vicinal diketones and dimethyl sulphide in HGB beers. The application of HGB mostly did not affect the beer ageing characteristics such as carbonyl compounds and thiobarbituric acid number.

High-rise building machines (HBMs) play a critical role in the successful construction of super-high skyscrapers, providing essential support and ensuring safety. The HBM’s climbing system relies on a jacking mechanism consisting of several independent jacking cylinders. A reliable control system is imperative to maintain a smooth posture of the construction steel platform (SP) under the action of the jacking mechanism. This research introduces three multivariate time series neural network models—namely, Long Short-Term Memory (LSTM), Gated Recurrent Unit (GRU), and Temporal Convolutional Network (TCN)—to predict the posture of HBM. The models take pressure and stroke measurements from the jacking cylinders as inputs, and their outputs determine the levelness of the SP and the posture of the HBM at various climbing stages. The development and training of these neural networks are based on historical on-site data, with the predictions subjected to thorough comparative analysis. All proposed neural network models exhibit the capability to dynamically predict the posture of the HBM during the climbing process, using data from sensors. Notably, the GRU model shows better predictive performance.

This review is a first attempt at bringing together various concepts from research on wall- and magnetically-bounded turbulent flows. Brief reviews of both fields are provided: The main similarities identified are coherent (turbulent) structures, flow generation and transport barriers. Examples are provided and discussed.

Hypertension is one of the most common primary cardiometabolic diseases and is a major contributor to cardiac mortality and morbidity. Furthermore, cardiac risk factors such as obesity and sedentary lifestyle are often seen in hypertensive patients. Regular exercise acts against these risk factors and improves the overall health of an individual. High-intensity interval training appears to do so in a more efficient way. We used a systematic literature review (SLR) approach to provide an overview of the present literature highlighting the cardiovascular advantages of HIIT in hypertensive individuals. We reviewed 4004 articles from reputable journals published between 2013 and August 14, 2023, focusing on 7 selected papers for in-depth analysis. This systematic review revealed the protective effects of HIIT against cardiac complications in hypertension. All the reviewed articles showed a decrease in blood pressure and many other risk variables of cardiovascular diseases. However, guidelines for this exercise are needed for maximum benefits. Therefore, further research on HIIT is necessary to fully harness its potential.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

The ratio between blade height and chord, named aspect ratio (AR), plays an important role in compressor aerodynamic design. Once selected, it influences stage performance, blade losses, and the stage stability margin. The choice of the design AR involves both aerodynamic and mechanical considerations, and a reasonable aim is frequently to achieve a desired operating range while maximizing efficiency. For a fixed set of aerodynamic and geometric parameters there will be an optimal choice in AR that achieves a maximum efficiency. However, for a state-of-the-art aero-engine design optimality means multi-objective optimality, that is reaching the highest possible efficiency for a number of operating points while achieving a sufficient stability margin. To this end, the influence of the AR on the performance of the first rotor row of a multistage multi-objective high-speed compressor design is analyzed. A careful setup of the high-speed aerodynamic design problem allows the effect of the AR to be isolated. Close to the optimal AR, only a modest efficiency variation is observed, but a considerable change in compressor stability margin (SM) is noted. Decreasing the AR allows for an increasing efficiency, but at the expense of a reduced surge margin. This allows the designer to trade efficiency for stability. Increasing the AR, however, is shown to reduce both surge margin and efficiency, hence a distinct optimality in stability is observed for the analyzed rotor blade row. In this work, the optimality in surge margin with respect to AR is observed whereas a close to optimal efficiency. The predicted range from AR=1.10 to AR=1.64, is only indicative, considering that the definition of a multi-objective optimality requires balancing efficiency and surge margin and that the choice of balancing these two criteria requires making a design choice along a pareto optimal front.

Gut microbiota dysfunction is a key factor affecting chronic kidney disease (CKD) susceptibility. Puerariae Lobatae Radix (PLR), a traditional Chinese medicine and food homologous herb, is known to promote gut microbiota homeostasis, however, its role in renoprotection remains unknown. This study aimed to investigate the efficacy and potential mechanism of PLR to alleviate CKD. An 8-week 2% NaCl-feeding murine model was applied to induce CKD and evaluate the therapeutic effect of PLR supplementary. After gavage for 8 weeks, PLR significantly alleviated CKD-associated creatinine, urine protein increasement and nephritic histopathological injury. Moreover, PLR protected kidney from fibrosis by reducing inflammatory response and down-regulating the canonical Wnt / β-catenin pathway. Further, PLR rescued gut microbiota dysbiosis and protected high salt-induced gut barrier dysfunction. We found enrichment of Akkermansia and Bifidobacterium after PLR intervention, the relative abundance of which were in positive correlation with normal maintenance of renal histology and function. Next, fecal microbiota transplantation experiment verified that the positive effect of PLR on CKD was at least partially exerted through gut microbiota reestablishment and down-regulation of the Wnt / β-catenin pathway. Our study provides evidence for new function of PLR on kidney protection and put forward a potential therapeutic strategy target for CKD.

This study aimed to use biomineralization technology to improve the bond strength of fiber-reinforced lightweight aggregate concrete (LWAC) after exposure to temperatures of 300 °C and 500 °C. The specimens of a control group (Group A) and two experimental groups (Group B and Group C) were prepared. These specimens healed themselves in different ways after exposure to high temperatures and pull-out tests. The self-healing method of Group A involved placing the specimen into an incubator. The self-healing method of Group B was the same as that of Group A. The self-healing method of Group C involved immersing the specimen in a mixed solution of urea and calcium acetate for two days, then taking it out and placing it in an incubator for two days. A cycle of four days was undertaken until the desired age was reached. After the specimens were healed to the planned age, the first and secondary pull-out tests and repair compound identification were carried out. After exposure to a temperature of 300 °C and self-healing for 90 days, compared with the specimens in Group A, the relative bond strength ratios of the secondary pull-out tests of the specimens in Group C increased by 20.3%. This indicates that biomineralization can effectively improve the bond strength of LWAC after high-temperature damage.

In the broader landscape of cryptocurrency risk management, this study delves into the nuanced estimation of Value at Risk (VaR) for a uniformly weighted portfolio of cryptocurrencies, employing the bivariate Normal Inverse Gaussian distribution renowned for its semi-heavy tails. Utilizing high-frequency data spanning from January 1st, 2017, to October 25th, 2022, with a primary focus on Bitcoin and Ethereum, our research seeks to accentuate the resilience of VaR methodology as a paramount risk assessment tool. The essence of our investigation lies in advancing the comprehension of VaR accuracy by quantitatively comparing observed returns of both cryptocurrencies with their corresponding estimated values, with a central theme being the endorsement of the Normal Inverse Gaussian distribution as a potent model for risk measurement, particularly in the domain of high-frequency data. To bolster the statistical reliability of our results, we adopt a forward test methodology, showcasing not only a contribution to the evolution of risk assessment techniques in Finance but also underscoring the practicality of sophisticated distributional models in econometrics. Our findings not only contribute to the refinement of risk assessment methods but also highlight the applicability of such models in precisely modeling and forecasting financial risk within the dynamic realm of cryptocurrencies, epitomized by the case study of Bitcoin and Ethereum.

Ridge regression is one of the most popular shrinkage estimation methods for linear models. Ridge regression effectively estimates regression coefficients in the presence of high-dimensional regressors. Recently, a generalized ridge estimator was suggested by generalizing the uniform shrinkage of ridge regression to the non-uniform shrinkage, which was shown to perform well under sparse and high-dimensional linear models. In this paper, we introduce our newly developed R package “g.ridge” (the first version published on 2023-12-07 at https://cran.r-project.org/package=g.ridge) that implements both the ridge estimator and generalized ridge estimators. The package equips with the generalized cross-validation for automatic estimation of shrinkage parameters. The package also includes a convenient tool for generating a design matrix. By simulations, we test the performance of the R package under sparse and high-dimensional settings with the normal and skew-normal error distributions. From the simulation results, we conclude that the generalized ridge estimator is superior to the benchmark ridge estimator based on “glmnet”, and hence, it can be the most recommended estimator under sparse and high-dimensional models. We demonstrate the package using the intracerebral hemorrhage data.

Diabetic kidney disease (DKD) is a major cause of morbidity and mortality of type 2 diabetes mellitus (T2DM). Aim of this study was to investigate whether albumin structural alterations correlate with DKD severity and evaluate whether native and reduced albumin concentrations could complement the diagnosis of DKD. To this aim, one hundred and seventeen T2DM patients without (n=42) and with (n=75) DKD (DKD I-III upon KDIGO classification) were evaluated; total albumin concentration (tHA) was quantified by bromocresol green assay, while structural alterations were profiled assessed by liquid chromatography-high resolution mass spectrometry (LC-HRMS). The concentrations of albumin in native (eHA, effective albumin) and reduced (rHA) forms were then assessed. HRMS analyses showed a reduced relative amount of native albumin in DKD patients along with an increased abundance of altered forms, especially those bearing oxidative modifications. Accordingly, both eHA and rHA values varied along the stages of progressive renal failure, and alterations dose-dependently correlated with renal dysfunction. ROC curves analysis showed a significantly higher sensitivity and specificity of eHA and rHA with respect to tHA for the diagnosis of DKD. Importantly, at multivariable logistic regression analysis, eHA was identified as independent predictor of DKD.

This study investigates the influence of economic growth on CO2 emissions levels in three developed countries—Argentina, Equatorial Guinea, and South Korea—based on their status as high-income countries. We test the environmental Kuznets curve (EKC) hypothesis using the time series approaches to check the relationship and direction of causality among the variables over a sample spanning 1974–2020. The results show an inverted U-shaped short-run relationship in all three countries. In the long run, only South Korea supports the EKC hypothesis. Further, Granger causality results indicate the existence of causality. These long-run causal relationships between economic growth and emissions recommend one policy implication that wealthy governments must expand investments in renewable clean energy projects and R&D, with regulatory measures to suppress harmful environmental procedures and support environmentally friendly development.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

This study evaluated the effects of high-temperature and high-pressure treatment on the antioxidant and anti-inflammatory activities of carrot extracts. The total polyphenol and flavonoid content of heated carrot extract increased as the heating temperature increased, with 403.93 mg GAE/100 g and 53.14 mg CE/100 g at 150°C. DPPH and ABTs radical scavenging activity (IC50) of heated carrot extract also increased as the heating temperature increased, with 4.65 mg/mL and 7.31 mg/mL, respectively, at 150°C. The reducing power increased with the heating temperature. Heated carrot extract did not exhibit any temperature- or concentration-dependent cytotoxicity. Nitric oxide (NO) generation was suppressed as the heating temperature and NO production increased. The heated carrot extract showed a decrease in the production of dose-dependent TNF-α, IL-1β, and IL-6 compared to the control group. The above results show that heated carrot extract had effective antioxidant and anti-inflammatory activities.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

Treatment options for sarcopenia are currently limited, primarily relying on two main therapeutic approaches: resistance-based physical activity and dietary interventions. However, details about specific nutrients in the diet or supplementation are unclear. Our objective is to investigate the relationship between nutrient intake and lean mass, function, and strength. Data were derived from the Gothenburg H70 birth cohort study in Sweden, including 719 70-year-olds born in 1944 (54,1 % females). For independent variables, the diet history method (face-to-face interviews) was used to estimate habitual food intake during the preceding three months. Dependent variables were gait speed (muscle performance), hand grip strength (muscle strength) and appendicular lean soft tissue index (ALSTI). Linear regression analyses were performed to analyze the relationship between the dependent variables and each of the covariates. Several nutrients were positively associated with ALSTI, such as polyunsaturated fatty acids (DHA, EPA), selenium, zinc, riboflavin, niacin equivalent, vitamin B12, vitamin D, iron, and protein. After correction for multiple tests, there were no remaining correlations with handgrip and gait speed. Findings of positive correlations for some nutrients with lean mass suggest a role for these nutrients for maintaining muscle volume. These results can be used to inform clinical trials to expand the preventive strategies and treatment options for individuals at risk of muscle loss and sarcopenia.

Cervical cancer, primarily caused by high-risk human papillomavirus (HR-HPV) types 16 and 18, is a major global health concern. Persistent HR-HPV infection can progress from reversible pre-cancerous lesions to invasive cervical cancer, which is driven by the oncogenic activity of human papillomavirus (HPV) genes, particularly E6 and E7. Traditional screening methods, including cytology and HPV testing, have limited sensitivity and specificity. This review explores the ap-plication of p16/Ki-67 dual-staining cytology for cervical cancer screening. This advanced im-munocytochemical method allows for simultaneously detecting p16 and Ki-67 proteins within cervical epithelial cells, offering a more specific approach for triaging HPV-positive women. Dual staining and traditional methods are compared, demonstrating their high sensitivity and negative predictive value but low specificity. The increased sensitivity of dual staining results in higher detection rates of CIN2+ lesions, which is crucial for preventing cervical cancer progression. However, its low specificity may lead to increased false-positive results and unnecessary biopsies. The implications of integrating dual staining into contemporary screening strategies, particularly considering the evolving landscape of HPV vaccination and changes in HPV genotype prevalence are also discussed. New guidelines and further research are necessary to elucidate the long-term effects of integrating dual staining into screening protocols.

Experimental investigations were conducted to uncover the impact of cavitation control - through the use of riblets (mesoscale surface structuring) - on cavitating flows around a circular cylinder. First, the dynamics of cavitation in the flow behind a finite cylinder (without riblets) was unveiled by visualizing the cavitation clouds and measuring the lift force fluctuations acting on the cylinder. Second, as a significant step forward, a comprehensive explanation was provided for the mechanism of cavitation control using two bio-inspired riblet morphologies positioned in different orientations and locations on the cylinder. For the first time, the effects of these tiny structures on the flow dynamics and the associated cavitation process were scrutinized. This showed that scalloped riblets, with their curved design, induced secondary vortices near their tips and distorted primary streamwise vortices, and that high velocity gradients near the jagged pattern peaks of sawtooth riblets delayed flow separation, which affected cavitation.

Background: In military flight operations fighter pilots work during flights constantly under hyperoxic breathing conditions with supplemental oxygen in varying hypobaric environments. These conditions are suspected to cause oxidative stress to neuronal organ tissues. For civilian flight operations the Federal Aviation Administration (FAA) also recommends supplemental oxygen for flying under hypobaric conditions equivalent to higher than 3048m altitude and makes it mandatory for conditions equivalent of more than 3657m altitude. Aim: We hypothesized that hypobaric-hyperoxic civilian commercial and private flight conditions with supplemental oxygen in a flight simulation in a hypobaric chamber at 2500m and 4500m equivalent altitude would cause significant oxidative stress in healthy individuals. Methods: 12 healthy subjects (6m, 6f, mean age 35,7yrs) from a larger cohort were selected to perform a 3hrs flight simulation in a hypobaric chamber with increasing supplemental oxygen levels (35%,50%,60% and 100% FiO2 via venturi valve equipped face mask) switching back and force between simulated altitudes of 2500m and 4500m. Arterial blood pressure and oxygen saturation were constantly measured via radial catheter and blood samples for blood gases taken from the catheter at each altitude and oxygen level. Additional blood samples from the arterial catheter at baseline and 60% oxygen at both different altitudes were centrifuged inside the chamber and the serum frozen instantly at minus 21°Celsius for later analysis of the oxidative stress markers malondialdehyde low density lipoprotein (M-LDL) and glutathione-peroxidase (GLP) via elisa test. Results: 11 subjects finished the study without adverse events. Whereas PO2 levels increased in the mean with increasing oxygen levels from baseline 96.2 mmHg to 160.9 mmHg at 2500m altitude and 60% FiO2 and 113.2 mmHg at 4500m altitude and 60% FiO2, there was no significant increase in both oxidative markers from baseline to 60% FiO2 at these simulated altitudes. Some individuals had a slight increase, some not at all or even a slight decrease. A moderate correlation (Pearson correlation coefficient 0,55) existed between subject age and glutathione peroxidase levels at 60% FiO2 at 4500m altitude. Conclusion: Supplemental oxygen of 60% FiO2 in a flight simulation comparing to flying in cabin pressure levels equivalent to 2500m-4500m altitude does not lead to a significant increase or decrease in the oxidative stress markers M-LDL and GLP in serum of arterial blood.

This paper focuses on the impact that urban traffic has on the environment. The study characterizes the global effect of GHG emissions, including the ecologic evaluation and the characterization, normalization, and evaluation factor. The work makes a detailed survey of the different modes of driving and their influence on engine performance as one of the principal causes of gas emissions during the combustion process. The article analyzes six types of vehicles equipped with different engine configurations: diesel and gasoline, GLP and GNC, hybrid electric, and plug-in hybrid electric. Simulation of the driving mode under various operational conditions for every type of engine results in energy consumption, thus, in GHG emissions, carbon dioxide and monoxide, nitrogen oxides, and Sulphur dioxide. The study concludes that a reduction in vehicle speed, thus in the engine revolutions, has positive effects on engine combustion and gasses emissions, which is reduced by 27.5%. The study also concludes that the limitation in driving mode, avoiding sharp and sudden acceleration, may reduce up to 45% of GHG emissions. The changes applied in the driving mode improve the air quality in the urban environment, reducing the content of GHG from 39% to 61%.

Ontological premises have profound theoretical implications. This analysis posits a single, universal structure composed of two ontic entities: discrete, quantized units of space ("Planck Spheres") and a State of Absolute Nothingness (the "SOAN"). Planck Spheres and the SOAN form a physical, ultra-high (3 x N) dimensional space ("Planck Space") and a discrete 3D space (or "4D spacetime"). Together, Planck Space and 4D spacetime form a tightly integrated ((3 x N) + 3) hyperspace (the "Dual Ontology"). Critically, a one-to-one mapping and identity exists between the Planck Spheres comprising 4D spacetime and Planck Space. The Dual Ontology conjecture supports radically simplified physical explanations for three distinct areas of theoretical physics: First, the conjecture reconciles fundamental issues in Special Relativity and quantum mechanics by explaining why single and N-body quantum states (a) dynamically evolve in 4D spacetime subject to the speed of light and (b) instantaneously collapse in a physical Planck Space that is not subject to Special Relativity. Second, the temporal and physical asymmetry between the dynamic evolution of quantum states in 4D spacetime subject to Special Relativity and the instantaneous collapse of quantum states in a Planck Space where Special Relativity is inapplicable explains quantum path irreversibility and the arrow of time. Third, at or near the heat death of 4D spacetime, the instantaneous collapse of the energy content of Planck Space and the simultaneous transition of 4D spacetime's extremely widely dispersed energy content to a non-singular, generally localized volume at t = 0 explains 4D spacetime's isotropy, homogeneity, extremely high energy, pressure, and temperature, flatness, and low gravitational entropy. It also explains the horizon and fine-tuning problems.

In this study, alfalfa silage with different packing densities (500 kg/m3, 600 kg/m3 and 700 kg/m3) were set up under outdoor high temperature and indoor normal temperature. The chemical composition, fermentation quality and microbial community of alfalfa silage were analyzed. The results showed that DM and WAC content decreased with the increase of density. When the density is 600kg/m3, CP content reaches the maximum and ADF content is the lowest. Temperature has a certain effect on alfalfa silage. The content of Lactobacillus plantarum fermented at high temperature is lower than that fermented at normal temperature. At the same time, the content of Lactobacillus plantarum decreased with the increase of packing density. However, the content of Lactobacillus plantarum was the lowest when the packing density was 600 kg/m3 at high temperature. In summary, this study explained the effects of different temperature and density on alfalfa fermentation quality and microbial community, and clarified that the density should be reasonably controlled within 600 kg/m3 during alfalfa silage, providing theoretical support for production practice.

Spectral image analysis has the potential to replace traditional approaches for assessing plant responses to different types of stress including herbicide, through non-destructive and high-throughput screening (HTS). Therefore, this study was conducted to develop a rapid bioassay method using a multi-well plate and spectral image analysis for diagnosis of herbicide activity and mode of action. Crabgrass (Digitaria ciliaris) as a model weed was cultivated in multi-well plates and subsequently treated with 6 herbicides with different modes of action when they reached the 1-leaf stage, using only a quarter of the recommended dose. To detect plant response to herbicides, plant spectral images were acquired after herbicide treatment using RGB, infrared (IR) thermal, and chlorophyll fluorescence (CF) sensors and analyzed for diagnosing herbicide efficacy and mode of action. Principal Component Analysis (PCA) using all spectral data successfully distinguished herbicides and clustered depending on their modes of action. The performed experiments have shown that the multi-well plate assay combined with spectral image analysis can be successfully applied for herbicide bioassay. In addition, the use of spectral image sensors, especially in CF image, would facilitate HTS by enabling rapid observation of herbicide response, as early as 3 hours after herbicide treatment.

The study focuses on a novel porous TiNi-based material for ophthalmic orbital implants which was produced by self-propagating high-temperature synthesis (SHS) and, after proper surface modification, possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

The aim of the study was to compare the standard baseline imaging, with extended radiological staging. To assess our hypothesis, we performed a prospective, single-centre study which included 132 participants recruited between October 2015 and March 2020. Descriptive statistics, the Friedman and chi-squared tests were performed and p &lt; 0.05 was considered significant. Patients were grouped into two cohorts, CT scan cohort (n=87) and PET-CT cohort (n=43). In the first group the originally determined disease stage changed in 36.8 % of cases, in second group in 51.2 %. The consistency between assessment of axillary lymph nodes by imaging (cN) and the postoperative pathology report (pN) was evaluated. In most cases, clinical and pathological evaluation of involved nodes was consistent, for CT scan the result was χ2(1) = 18.98; p &lt; 0.001, for PET-CT the result was χ2(1) = 6.41; p = 0.03. Highly customized radiation therapy defined as dose boost within the involved lymph nodes, not covered by surgeon, was applied in nine patients.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

(1) Background: CTA has validated the use of pericoronary adipose tissue (PCAT) attenuation as a credible indicator of coronary inflammation and plays a crucial role in coronary artery disease (CAD). This study aimed to evaluate the long-term effects of high-dose statins on PCAT attenuation at coronary lesion sites and changes in plaque distribution; (2) Methods: Our prospective observational study included 52 patients (mean age 60.43) with typical chest pain, a low-to-intermediate likelihood of CAD, and documented atheromatous plaque through CCT. We utilized advanced features of the CaRi-Heart® and syngo.via Frontier® systems to assess coronary plaques and changes in PCAT attenuation; (3) Results: Changes in plaque morphology were investigated, revealing significant alterations. Notably, in mixed plaques, calcified portions increased (p &lt; 0.0001), while non-calcified plaque volume (NCPV) decreased (p = 0.0209). PCAT attenuation generally decreased after one year and remained low, indicating reduced inflammation in the following arteries: LAD (p = 0.0142), LCX (p = 0.0513), and RCA (p = 0.1249). The CaRi-Heart® risk also decreased significantly (p = 0.0041). Linear regression analysis demonstrated a correlation between increased PCAT attenuation and higher volumes of NCPV (p &lt; 0.0001, r = 0.3032) and lipid-rich plaque volume (p &lt; 0.0001, r = 0.3281); (4) Conclusions: Our study provides evidence that high-dose statin therapy significantly reduces CAD risk factors, inflammation, and plaque vulnerability, as evidenced by the notable decrease in PCAT attenuation, a critical indicator of plaque progression.

UNESCO highlights socio-emotional, cognitive, and behavioral learning as critical for advancing sustainability. As major events, sports generate significant social, economic, and environmental impacts. This study analyzed how academic background, gender, age, sport type, and modality influenced elite Colombian Olympic and Paralympic athletes' socio-emotional competencies. Methods: Colombian elite athletes who were members of the “Support to the Excellence Coldeportes Athlete” participated in the study. The total population studied included 334 Colombian elite athletes: mean age 27.10 ± 6.57 years old with 13.66 ± 6.37 years practicing his/her sports modality. The socio-emotional competencies of the participants were assessed using the Socio-emotional Competencies Scale (SECS). Results: Men scored higher in interpersonal regulation, self-awareness, conflict resolution, and emotional regulation. Younger athletes (≤25 years) had higher self-consciousness. Individual versus team sports did not differ. Paralympians showed higher motivation, self-awareness, teamwork, and emotional regulation. University educated athletes scored higher in motivation, self-awareness, teamwork, and empathy. All competencies positively correlated. Conclusion: Individualized interventions targeting improved socio-emotional performance are vital for sustainability and should account for differences across gender, age, education, and disability status.

This work presents a unique two-element high-isolated orthogonally CPW-fed UWB Multiple Input Multiple Output (Ultra-wideband) antenna. The antenna is supported by the 52.8 × 29 mm2 FR-4 substrate, which has a dielectric constant of 4.3 and a thickness of 1.6 mm. The suggested MIMO antenna reduces mutual coupling by separating the two single UWB antennas that make up the antenna. The suggested antenna achieves a voltage standing wave ratio (VSWR) of less than two and more than 86% radiation efficiency over the whole range of interest. The antenna's performance is assessed using both modeling and experimentation. Return loss, efficiency, gain, bandwidth, and Voltage Standing Wave Ratio (VSWR) are all factors in which the design performs well. The suggested antenna is evaluated using the CST Microwave Studio. The antenna prototype model is constructed, tested, and measured in order to validate the simulation return-loss results. There is good agreement between the measured and simulated results.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

To address friction and wear challenges in dry contacts, manufacturers often employ self-lubricating materials. Graphite and its derivatives stand out as particularly suitable due to their exceptional tribological properties. However, under intense friction conditions, graphite can experience a decline in lubricating efficiency due to severe abrasive wear. This abrasive damage results in elevated activated carbon surfaces with increased surface energy, fostering greater adhesion between sliding surfaces. The low friction coefficient of graphite is not an inherent property but rather a consequence of water vapor adsorption by the material. Beyond 150°C, desorption of the vapor occurs, leading to a transition in the friction coefficient from µ=0.1 to µ=0.6. To address this issue, impregnation solutions for self-lubricating materials have been developed, with various compositions tailored to specific objectives. Common types include molybdenum disulfide, soft metals, or polymers. In this predominantly experimental study, the impact of polymer impregnation on the evolution of friction force and wear rate in graphite material bearings subjected to a dry fretting contact under severe thermal stresses at 270°C was investigated. Additionally, the mechanical stresses in the bearings throughout different phases of our tests were analyzed using a numerical model.

This study advances the field of solar irradiance nowcasting by introducing a discrete-level classification approach, diverging from traditional continuous measurement methods. Grounded in a need for cost-effective and modular solutions, the research employs high-resolution computer vision coupled with a deep learning framework to predict Direct Normal Irradiance (DNI). By harnessing the capabilities of a Logitech C900 1080p HD camera and an NVIDIA Jetson module, the study achieves real-time data processing, pivotal for CSP systems' operational efficiency. The core of the methodology is the ResNet-50 convolutional neural network, refined via transfer learning on a bespoke dataset, culminating in a predictive accuracy of 85.78%. This discrete classification model contrasts with conventional, costly instruments like the MS-57, offering a novel and accessible alternative for DNI estimation. Such innovation not only demonstrates high predictive accuracy but also signifies a shift towards less resource-intensive and more adaptable solar energy forecasting tools, contributing a significant leap towards optimizing renewable energy systems.

The Trail Making Test (TMT) is one of the most commonly administered tests in clinical and research neuropsychological settings. The two parts of the test [part A (TMT-A) and part B (TMT-B)] enable the evaluation of visuoperceptual tracking and processing speed (TMT-A), as well as divided attention, set-shifting and cognitive flexibility (TMT-B). The main cognitive processes that are assessed using TMT, i.e. processing speed, divided attention and cognitive flexibility, are often affected in patients with stroke. Considering the wide use of TMT in research and clinical settings since its introduction in neuropsychological practice, the purpose of our review was to provide a comprehensive overview on the use of TMT in stroke patients in an attempt to mainly identify its role for the evaluation of post-stroke cognitive dysfunction and progression over time, the identification of the underlying neuroanatomical pathology related to impaired TMT performance, and the association with other stroke outcomes, such motor function, driving ability and quality of life. Our comprehensive review underscores that the TMT stands as an invaluable asset in the stroke assessment toolkit, contributing nuanced insights into diverse cognitive, functional, and emotional dimensions. As research progresses, continued exploration of the TMT potential across these domains is encouraged, fostering a deeper comprehension of post-stroke dynamics, and enhancing patient-centered care across hospitals, rehabilitation centers, research institutions, and community health settings. Its integration into both research and clinical practice reaffirms TMT status as an indispensable instrument in stroke-related evaluations, enabling holistic insights that extend beyond traditional neurological assessments.

The pharmaceutical industry is undergoing a shift in processing methods for small-scale production (250-1000 kg/a), leading to an increased focus on continuous production research. Various concepts were developed to overcome challenges in small-scale crystallization for the production of high-quality products. However, further optimization is needed to enhance the industrial applicability of these concepts. This study aims to demonstrate the practical applicability of the Slug Flow Crystallizer (SFC) in the pharmaceutical industry by extending its use to a wider range of substance systems for small-scale API production. Employing an experimental strategy, the research seeks to rapidly assess the SFC's potential for achieving uniform, high-purity product yields, emphasizing the importance of factors such as slug flow stability, residence time distribution, and substance-specific crystallization criteria. This, coupled with our previously published model-based strategy, forms a comprehensive methodology to explore crystallization behavior and modeling for a variety of substance systems within the SFC. The ultimate goal of this study is to showcase the practicality of the SFC in the pharmaceutical industry, enabling the way for its reliable use in long-term, small-scale continuous crystallization and the production of high-quality pharmaceutical products.

Landscape changes based on spectral responses allow showing plant cover changes through diversity, composition, and ecological connectivity. The spatial and temporal vegetation dynamics of the Bijagual Massif from 1986 to 2021 were analyzed as a measure of ecological integrity, conservation, and territory. The covers identified were high open forest (Hof), dense grassland of non-wooded mainland (Dgnm), a mosaic of pastures and crops (Mpc), lagoons (Lag), and bare and degraded lands (Bdl). The Bijagual Massif has 8,574.1 ha. In 1986, Dgnm occupied 42.6% of the total area, followed by Mpc (32.8%) and Hof (24.5%); by 2000, Mpc and Hof increased (43.7 and 28.1%, respectively), while Dgnm decreased (28%); by 2021, Dgnm was restricted to the northeastern zone and continued to decrease (25.2%), Mpc occupied 52.9%, Hof 21.7% and Bdl 0.1%. Of the three fractions of the connectivity probability index, only dPCintra and dPCflux contribute to ecological connectivity. Hof and Dgnm show patches with biota habitat quality and availability. Between 1986 and 2021, Dgnm lost 1,489 ha (41%) and Hof 239.5 ha (11%). Mpc replaced various covers (1,722.2 ha; 38%) in 2021. Bijagual has a valuable biodiversity potential limited by Mpc. Territorial planning and sustainable agroecological and ecotourism proposals are required due to the context of the ecosystems.

Unsupervised physics-informed deep learning can be used to solve computational physics problems by training neural networks to satisfy the underlying equations and boundary conditions without labeled data. Parameters such as network architecture and training method determine the training success. However, the best choice is unknown a priori as it is case specific. Here, we investigated network shapes, sizes, and types for unsupervised physics-informed deep learning of the two-dimensional Reynolds-averaged flow around cylinders. We trained mixed-variable networks and compared them to traditional models. Several network architectures with different shape factors and sizes were evaluated. The models were trained to solve the Reynolds-averaged Navier-Stokes equations incorporating Prandtl's mixing length turbulence model. No training data were deployed to train the models. The superiority of the mixed-variable approach was confirmed for the investigated high Reynolds number flow. The mixed-variable models were sensitive to the network shape. For the two cylinders, differently deep networks showed superior performance. The best fitting models were able to capture important flow phenomena such as stagnation regions, boundary layers, flow separation, and recirculation. We also encountered difficulties when predicting high Reynolds number flows without training data

Advances in technology have introduced remarkable capabilities, particularly in the realm of gathering and accessing vast amounts of data, which has led to the emergence of the "Big Data" era, presenting exciting opportunities to harness the wealth of the generated information. Traffic management centers comprise a stakeholder that can exploit such data towards improving road network operation. This research, explores the utilization of real traffic data, collected by distinct sources on an interurban motorway: static location based aggregate traffic data and probe vehicle data. The first is collected by traffic detectors, while the second involves patrol vehicles’ GNSS data. The traffic quantity analysed is vehicle speed, while specific emphasis has been given on the ap-plication of heatmaps to represent daily traffic patterns and the utilization of k-means clustering. The performed analysis demonstrates the importance of considering spatiotemporal variables as a unified entity when analysing speed in transportation networks. The limitations of using patrol vehicles as estimators of ambient speed, especially in low and heavy traffic conditions, are deline-ated, while the dual purpose of data gathered from these vehicles towards enhancing driving performance and enabling detector maintenance is emphasized. Valuable traffic insights are offered through comprehensive spatiotemporal speed behavior analysis and data combination. The inte-gration of these techniques enhances decision-making for a streamlined and secure transportation system

Photovoltaic systems and wind energy systems are generally used in distributed system. However, zero-sequence and harmonic currents occur due to photovoltaic systems, and positive-sequence harmonic currents occur due to wind turbines. Thus, the sheath current in high voltage cables increases due to these currents and poor power quality in distributed generation plants. Metal parts of the cable are grounded to prevent the negative effects of sheath currents. When long high voltage cable lines are grounded with the method in the literature, high sheath current and voltage occur on the cable sheath. Therefore, the SSBLR method is designed as a new method for the distributed generation system. The SSBLR method has been optimized with prediction methods and multi-objective optimization methods to prevent negative effects of the sheath current. Pareto optimal method is used as multi-objective optimization method, and artificial neural network, hybrid artificial neural network and regression methods are used as prediction method. The most dominant result is searched using different estimation and optimization methods in pareto optimal method. When the artificial neural network-genetic algorithm hybrid method is used as a prediction method, and genetic algorithm used as optimization method, significant decreases are observed in sheath current and voltage.

Ultra-low radioactive titanium alloy is a promising material for the manufacture of low-background detectors, which are being developed for experiments in astroparticle physics and neutrino astrophysics. Structural titanium is manufactured on an industrial scale from titanium-sponge. The ultra-low-background titanium-sponge can be produced on an industrial scale with a contamination level of less than 1 mBq/kg of uranium and thorium isotopes. The pathways of contaminants during the industrial production of structural titanium have been analyzed. The measurements have been carried out using two methods: inductively coupled plasma spectroscopy (ICP-MS) and gamma-spectroscopy using high-purity germanium detectors (HPGe). It has been shown that the level of contamination with radioactive impurities does not increase during remelting of titanium-sponge and mechanical processing. We examined titanium-alloys samples obtained at different stages of titanium production, namely, an electrode compaction, a vacuum arc remelting with a consumable electrode (VAR), and a cold rolling of titanium-sheets. It has been found out that all studied samples will be a source of uranium and thorium contamination of the final titanium-alloys. It has been established that the only product allowed obtaining ultra-low-background titanium was the VT1-00 which is manufactured without master alloys addition..

There are many applications of anomaly detection in IoT domain. IoT technology consists of large number of interconnecting digital devices not only generating huge data continuously but also making real-time computations. Since IoT devices are highly exposed due to Internet, they frequently meet with the challenges of illegitimate accesses in the form of intrusions, anomaly, fraud, etc. Identifying these illegitimate accesses in IoT domain can be an exciting research problem. In numerous applications fuzzy clustering and rough set theory have been successfully employed. As the data generated in IoT domains are high-dimensional, the clustering methods used for lower dimensional data cannot be applied efficiently. In this article, mixed approaches consisting of nano topology and fuzzy clustering techniques are proposed for anomaly detection. First of all, the nano topology is generated to find lower dimensional apace and then a couple of well-known fuzzy clustering techniques are employed on it for the efficient anomaly detection. The effectiveness of the proposed approaches is evaluated using time-complexity analysis, experimental studies with a synthetic dataset and a real-life dataset along with comparative studies with traditional fuzzy clustering approaches namely fuzzy c-means clustering (FCM) algorithm, Gustafson-Kessel (GK) Algorithm, Gath-Geva (GG) Algorithm, Mahalanobis Distance based Fuzzy C-Means algorithm (M-FCM), and Common Mahalanobis Distance based Fuzzy C-Means algorithm (CM-FCM). Experimentally, it has been found that the proposed approaches outperform the aforesaid algorithms in terms of detection rates, accuracy rates, false alarm rates and computational times.

Background: Oscillation and pulmonary expansion (OPE) therapy can decrease postoperative pulmonary complications in a general surgical population, but its effect after cardiac surgery has not been reported, to our knowledge. We hypothesized that using an OPE device after cardiac surgery before extubation would decrease pulmonary complications. Methods: This retrospective cohort study included adults undergoing elective open cardiac surgery at our institution from January 2018 through January 2019, who had an American Society of Anesthesiologists score of 3 or greater. For mechanically ventilated patients after cardiac surgery, a new OPE protocol was adopted July 1, 2019, comprising an initial 10-minute OPE treatment administered in-line with the ventilator circuit, then continued treatments for 48 hours after extubation. Severe postoperative respiratory complications (primary outcome measure) included need for antibiotics, increased supplemental oxygen use, and prolonged hospital length of stay (LOS). Demographic, clinical, and outcomes data were compared for patients before (usual care with postextubation hyperinflation) and after protocol implementation (OPE). Results: Of 104 patients, 54 patients received usual care, and 50 received OPE. Usual-care recipients had more men (74% vs 62%; P=.19) and were older (median, 70 vs 67 years; P=.009) than OPE recipients. The OPE group had a significantly shorter hospital LOS than the usual-care group (mean, 6.2 vs 7.4 days; P=.04). Other measures improved with OPE but did not reach significance: shorter ventilator duration (mean, 0.6 vs 1.1 days with usual care; P=.06) and shorter LOS in the intensive care unit (mean, 2.7 vs 3.4 days; P=.06). On multivariate analysis, intensive care unit LOS was significantly shorter for the OPE group (mean difference, 0.85 days; 95% CI, 1.65 to 0.06; P=.04). The OPE group had a lower percentage of postoperative complications (10% vs 20%). Conclusion: OPE therapy after cardiac surgery is associated with decreased ICU and hospital LOS.

High-grade gliomas are extremely fatal tumors, marked by severe hypoxia and therapeutic resistance. Autophagy is a cellular degradative process that can be activated by hypoxia, ultimately resulting in tumor advancement and chemo-resistance. Our study aimed to examine the link between autophagy markers expression in low (LGG) and high-grade gliomas (HGG). In 39 glioma cases, we assessed protein expression of autophagy markers LC3B, p62, and DRAM by immunohistochemistry (IHC) and mRNA expression of autophagy genes; PI3K, AKT, m-TOR, PTEN, ULK1, ULK2, UVRAG, Beclin 1 and VPS34 using RT-qPCR. Livak’s method was used to analyze the relative changes in gene expression and multi-variate Anova test and Spearman's correlation tests were performed for statistical significance. LC3B, p62, and DRAM expression were positive in 64.1%, 51.3%, and 28.2% of glioma cases respectively. The expression of LC3B and p62 was notably higher in HGG compared to LGG. VPS34 exhibited a significant differential expression and increased fold change and demonstrated strong positive correlations with Beclin1 (rs=0.768), UVRAG (rs=0.802), and ULK2 (rs=0.786) in HGG compared to LGG, thus highlighting the potential link between autophagy and glioma progression. We Provide preliminary data for functional analysis of autophagy using cell culture model and to identify potential targets for therapeutic interventions

This research investigates the fatigue crack propagation on the lower surface of rocket deflector troughs of offshore rocket launch platforms. Initially, a numerical model of the offshore rocket launch platform is established using ABAQUS based on the Extended Finite Element Method (XFEM). Subsequently, two variable parameters—namely, the initial crack length and initial tilt angle—are introduced. This research systematically analyzes the impact of these parameters on fatigue crack propagation patterns in both the maximum stress and maximum deformation regions of the deflector channels under the combined conditions of high temperature and impact. Finally, the research indicates that the propagation length of surface cracks in the deflector trough exhibits a trend of initial increase followed by a subsequent decrease with the increase in the preset inclination angle. Notably, the stable propagation rate of the crack in the region of maximum deformation surpasses that observed in the region of maximum stress. Through meticulous comparative analysis, it is evident that temperature loading significantly fosters the initiation and propagation of cracks, particularly in the upper region of the deflector channel's lower surface.

Road pavement monitoring represents the baseline to the pavement maintenance process. To quickly fix a damaged road, relevant authorities need a high-efficiency methodology that allows them to obtain data describing the current conditions of a network of roads. In urban areas, large-scale monitoring campaigns may be more expensive and not fast enough to describe how pavement degradation has evolved over time. Furthermore, at low speeds, many technologies are inadequate for monitoring the streets. In such a context, employing black box equipped vehicles to perform a routine inspection could be an excellent starting point. However, the vibration-based methodologies used to detect road anomalies are strongly affected by the speed of these vehicles. In this study, a statistical method was to analyze the effects of speed on road pavement conditions at different severity levels through the data recorded by taxi vehicles. Likewise introduced was a process that overcomes the speed effect when considering road surface conditions. The methodology proposed has succeeded in predicting the right damage severity level based on only two recorded parameters: speed and pavement deterioration index.

Understanding that organizational communication is crucial for the consistent functioning of any establishment, this research assesses its influence on work-life balance, organizational climate, and job satisfaction among Portuguese firefighters, a rarely studied group. Effective organizational communication is identified as a potential pathway for nurturing a favorable work setting and bolstering employee contentment, essential elements of work-life balance. Data compiled from a group of 102 firefighters, using a sociodemographic questionnaire, the Work Social Climate Scale, and Portuguese versions of the ICA Communication Audit Survey Instrument and the Labor Satisfaction Questionnaire S20/23, unveil multiple significant correlations among various dimensions of the ICA, the Work Social Climate Scale, and communication metrics. Explicitly, correlations were discerned between received and sent communications and aspects of implication, support, and cohesion. Links were also evident between desired communications and the control dimension. Positive and statistically significant relationships were further observed between received and sent communications, all five satisfaction dimensions, necessary outgoing communications and the physical environment, and required outgoing communications and benefits, highlighting the pivotal role of adept communication in augmenting work-life balance, organizational climate, and job satisfaction among firefighters.

This work deals with a novel porous TiNi-based material for ophthalmic orbital implants that was produced by high-temperature synthesis (SHS) and possesses a specific microstructure of its surface pores, which makes it attractive for biomedical use in implants. After preparation via SHS, the obtained porous TiNi material was etched in acidic environment, to get rid of its surface Ti2Ni secondary-phase particles. This was found to improve the material’s surface morphology, adding micro-roughness to its macro-rough pores. As a result, cell growth tests conducted on the material demonstrated improved cell adhesion and growth kinetics on such a porous material with improved roughness. Finally, the material was tested in vivo as an ophthalmic orbital implant, demonstrating good biocompatibility, good degree of biointegration with surrounding eyeball tissues, and no signs of rejection after as long as 180 days. Thus, the novel porous TiNi-based material shows promise for its use in ophthalmic implantology, for instanse for manufacturing musculoskeletal stumps of the eyeball after evisceration, as it is biocompatible, has a high tissue-implant integration potential and demonstrates reduced risks of exposure and rejection of the implant.

Genetic engineering and directed evolution are effective methods to address the low yield and poor industrialization level of microbial target products. The current research focus is on how to efficiently and rapidly screen beneficial mutants from constructed large-scale mutation libraries. Traditional screening methods such as plate screening and well plate screening are severely limited in their development and application due to their low efficiency and high costs. In the past decade, microfluidic technology has become an important high-throughput screening technology due to its fast speed, low cost, high automation, and high screening throughput, and it has developed rapidly. Droplet-based microfluidic high-throughput screening has been widely used in various fields such as strain/enzyme activity screening, pathogen detection, single-cell analysis, drug discovery, and chemical synthesis, and has been widely applied in industries such as materials, food, chemicals, textiles, and biomedicine. In particular, in the field of enzyme research, droplet-based microfluidic high-throughput screening has shown excellent performance in discovering enzymes with new functions, improved catalytic efficiency or stability, acid-base tolerance, etc. Currently, droplet-based microfluidic high-throughput screening technology has achieved high-throughput screening of enzymes such as glycosidase, lipase, peroxidase, protease, amylase, oxidase, and transaminase, as well as high-throughput detection of products such as riboflavin, coumarin, 3-dehydroquinate, lactic acid, and ethanol. This article reviews the application of droplet-based microfluidics in high-throughput screening, with a focus on high-throughput screening strategies based on UV, visible, and fluorescence spectroscopy, including labeled optical signal detection screening, as well as label-free electrochemical detection, mass spectrometry, Raman spectroscopy, nuclear magnetic resonance, etc. Furthermore, the research progress and development trends of droplet-based microfluidic technology in enzyme modification and strain screening are also introduced.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

We are introducing a highly efficient 48-channel ultrasound beamforming system ideal for ultrasound endoscopy applications. The system includes a transmitter and a receiver, which allow for low-area, high-resolution imaging acquisition. The transmitter uses a charge redistribution HV (high voltage) scheme to generate three-level pulses that actuate the transducer, implemented with the standard CMOS process for optimal cost and power savings. Meanwhile, the receiver features a sub-array structure and a delay generator that reduces area usage. To achieve high-resolution ultrasound imaging acquisition with low computational power, we developed the Shift Coherence Factor (SCF) algorithm, which is hardware-friendly. This approach delivers a lateral resolution over 20% better than the conventional delay and sum (DAS) algorithm, with a contrast ratio of over 30 dB. The system was implemented in a 180 nm standard CMOS process with an area of 24.98 mm2, power consumption of 8.23 mW per channel, achieving a delay resolution of 8.33 ns, and a low-area implementation of 0.52 mm2 per channel. The system offers high-quality imaging acquisition with minimal additional area and power consumption, which has great potential for 3D imaging or catheterized ultrasound systems.

We study the tight focusing properties of generic bright and dark HyOPS beams in the presence of primary coma. The role of the polarization singularity index and handedness of the polarization of the HyOPS beams on the focused structure has been discussed. Results have been presented for the total intensity, component intensities, and component phase distributions for left-, and right-handed bright and dark star and lemon types singularities. The presence of primary coma distorted the focal plane intensity distributions for both positive and negative index generic C-points. Coma is known to disturb the circular symmetry of the focal plane intensity distribution. Similarly in tight focusing polarization is known to disturb the symmetry. Therefore, a beam with structured and inhomogeneous polarization distribution tightly focused under the influence of coma is a fit case to study. It is found that the presence of primary coma aberration in the focusing system produces a positional shift of the high-intensity peaks and a reduction of the intensity on one side of the center. As the strength of the primary coma increases, the focal plane intensity distributions shift more and more toward the right from the initial position. Unlike the scalar vortex case, in the case of HyOPS beams, the focal plane intensity distribution undergoes rotation, as the helicity of the HyOPS beams is inverted, in addition to shifting. All the component phase distributions are found to be embedded with phase vortices of charge ±1.

The incidence and mortality of cervical cancer are high in Romania compared to other European countries, particularly for locally advanced cervical cancer cases, which are predominant at the time of diagnosis. Widely accepted therapeutic guidelines indicate that the treatment for locally advanced cervical cancer consists of concurrent chemoradiotherapy (total dose 85-90Gy at point A), with surgery not being necessary as it does not lead to improved survival and results in significant additional morbidity. In Romania, the treatment for locally advanced cervical cancer differs, involving lower-dose chemotherapy (total dose 60-65Gy at point A), followed by surgery which, under these circumstances, ensures better local control. In this regard, we attempted to evaluate the role and necessity of surgery in Romania, considering that in our study, residual lesions were found in 55.84% of cases on resected specimens, especially in cases with unfavorable histology (adenocarcinoma and adenosquamous carcinoma). This type of surgery was associated with significant morbidity (28.22%) in our study. The recurrence rate was 24.21% for operated patients compared to 62% for non-operated patients receiving suboptimal concurrent chemotherapy alone. In conclusion, In Romania, surgery will continue to play a predominant role until radiotherapy achieves the desired effectiveness for local control.

Cavitation resulting from underwater explosions in compressible multiphase or multicomp-onent flows presents significant challenges due to the dynamic nature of shock-cavitation-structure interactions, as well as the complex and discontinuous nature of the involved interfaces. Achieving accurate resolution of interfaces between different phases or components, in the presence of shocks, cavitating regions, and structural interactions, is crucial for modeling such problems. Furthermore, pressure convergence in simulations involving shock-cavitation-structure interactions requires accurate algorithms. In this research paper, we employ the diffuse interface method, also known as the interface capturing scheme, to investigate cavitation in various underwater explosion test cases near different surfaces; free surface and a rigid surface. The simulations are conducted using the Unstructured Compressible Navier-Stokes (UCNS3D) finite volume framework employing central-weighted essentially non-oscillatory (CWENO) reconstruction schemes, utilising the five-equation diffuse interface family of methods. Quantitative comparisons are made between the performance of both models. Additionally, we examine the effects of cavitation as a secondary loading source on structures, and evaluate the ability of the CWENO schemes to accurately capture and resolve material interfaces between fluids with minimal numerical dissipation or smearing. The results are compared with existing high-order methods and experimental data, where possible, to demonstrate the robustness of the CWENO schemes in simulating cavitation bubble dynamics, as well as their limitations within the current implementation of interface capturing.

For both conventional and renewable energy conversion processes, computational fluid dynamics (CFD) has been used to address more energy-related challenges in recent decades. Using CFD to investigate vertical-axis wind turbines has become more common in recent years. The main goals of this application have been to more accurately predict the turbine's performance and to comprehend the complicated nature of the complex turbulent flow. The Vertical Axis Wind Turbine (VAWT) simulation for energy-generating applications has several intricate components. One of them is being aware of the chaotic flow that occurs during the first stages of the starting process, which influences overall effectiveness. In this article, the performance of the wind turbine was increased by using a passive flow control approach. The numerical research was carried out using Large Eddy Simulation for four alternative tip speed ratios in both cases, the classic and the optimized, equipped with a vortex trap on the exterior of the blades. The power and torque coefficient variations, as well as the velocity magnitude contours, show that the starting process may begin with a significant improvement in efficiency when flow control is used.

Oxidoreductase (OXR) enzymes are in high demand for biocatalytic applications in food industry and cosmetics: glucose oxidase (GOx), cellobiose dehydrogenase (CBDH), bioremediation: horseradish peroxidase (HRP), laccase (LAC), and medicine for biosensors and miniature biofuel cells (GOx, CBDH, LAC, HRP). They can be used in a soluble form and/or within the yeast cell walls expressed as chimeras on the surface of yeast cells (YSD), such as P. pastoris and S. cerevisiae. However, most of the current studies suffer from either low yield for soluble enzyme expression or low enzyme activity when expressed as chimeric proteins using YSD. This is always the case in studies dealing with heterologous expression of oxidoreductase enzymes, since there is requirement not only for multiple OXR genes integrations into the yeast genome (super transformations), and codon optimization, but also very careful design of fermentation media composition, and fermentation conditions during expression due to need for adding transition metals (copper, iron), and metabolic precursors of FAD and heme. Therefore, scientists are still trying to find optimal formula using above mentioned approaches, and most recently also using protein engineering and directed evolution for additional increase in the yield of recombinant enzyme production. In this review article we will cover all the current state of the art technologies and most recent advances in the field that yielded high expression level for some of these enzymes in specially designed expression/fermentation systems. We will also tackle and discuss new possibilities for further increase in fermentation yield by the cutting-edge technologies such are directed evolution, protein and strain engineering, high-throughput screening methods based on in vitro compartmentalization, flow cytometry and microfluidics.

We present a design of electrostatic comb driver to improve and investigate its actuation performance. The proposed electrostatic comb actuator (ECA) is composed of two set of interdigitated comb microstructures, the inner combs are fixed to form the fish-bone microstructures and the outer combs are movable and connected to crab-leg flexure beams microstructures. The ECA is investigated to optimize the actuation performance by changing the comb shape and the intersection angle of crab-leg flexure beams. The comb shapes are compared between the traditional rectangle shape and the trapezoid shape, while the intersection angles of crab-leg flexure beams are compared between 45°, 60°, and 90° on the influences of ECA displacement and stability characteristics. These parameters are investigated for their impacts on the dynamic comb displacement and driving voltage. Under the condition of a driving DC bias voltage of 100 volts, the ECA displacement is firstly increased and then gradually decreased by increasing the comb finger length. The maximum displacement of ECA with trapezoid comb is 47.2 μm while that of ECA with rectangle comb is 22.4 μm. By using trapezoid comb shape to replace the rectangle comb under the same conditions, the ECA displacement is improved 2-fold. To enhance the stability of ECA system, the intersection angle of 90˚ of crab-leg flexure beams shows highest stability that is great better than the intersection angle of 45° and 60° of crab-leg flexure beams by increasing the driving different DC bias voltage to 100 volts on ECA. The stability of the ECA with the intersection angle of 90° of crab-leg flexure beams is enhanced 1.1-fold and 1.4-fold compared to that of 45° and 60° of crab-leg flexure beams, respectively. This design provides an optimized approach to the electrostatic comb actuator that can be used expansively in the gyroscope, motion sensor, position sensor, imaging sensor, optical sensor, and so on.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

The superficial quality of the strip is a very important issue in steel production; the profile, flat-ness, and geometry of strip are indicators of supreme quality. Considering the dimensions, the thickness is one of the most important variables in the production of strip. In the present study the elastic curve of Back Up Rolls (BUR) is analyzed, considering them as simply supported beams as well as the effect of rolls on the profile of the strip, specifically in the strip edge pro-ducing edge drop. The analysis is simulated with a model in 3D using a Finite Element Method (FEM) considering +0.039mm crown on Back Up Roll and +0.101mm crown on Work Roll (WR). The results showed that there is an instability zone of 76mm in the strip edge, this geometry is symmetrical in both ends of the strip, it was validated with the results of compact X-ray thick-ness gauge from a 4-high cold mill. This study not only provides a theoretical basis for the edge drop, but also provides the basis for the understanding of deformation on rolls used in rolling mill processes and their effect on the thickness, profile, shape, and dimensional quality of strips.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

Abstract: Objectives: To establish the expression profile of N6-methyladenosine(m6A) modifications in the hippocampus of mice with diabetic cognitive impairment (DCI) and elucidate the potential regulatory mechanism. Methods: A DCI model was established by feeding a high-fat diet to C57BL/6J mice. m6A and RNA sequencing was conducted to profile the m6A-tagged transcripts in the hippocampus. Results: Methylated RNA immunoprecipitation with next-generation sequencing and RNA sequencing analyses yielded differentially m6A-modified and expressed genes in the hippocampus of DCI mice, which were enriched in pathways involving synaptic transmission and axonal guidance. Mechanistic analyses revealed a remarkable change in m6A modification levels through alteration of the mRNA expression of m6A methyltransferases (METTL3 and METTL14) and demethylase (FTO) in the hippocampus of DCI mice. Conclusions: We identified a co-mediated specific RNA regulatory strategy that broadens the epigenetic regulatory mechanism of RNA-induced neurodegenerative disorders associated with metabolic and endocrine diseases.

This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

The MAGIC (Major Atmospheric Gamma-ray Imaging Cherenkov) Florian Goebel telescopes are a system of two Cherenkov telescopes located on the Canary island of La Palma (Spain), at the Roque de Los Muchachos Observatory, and operating in stereo mode since 2009. Their low energy threshold (reaching 15 GeV) allows the study of Active Galactic Nuclei (AGNs) in the very-high-energy gamma ray range with an impressive sensitivity up to the redshift limit of the existing IACT systems. MAGIC has collected many discoveries and comprehensive studies of different kinds of galaxies and their AGNs, also in a multi-wavelength context, expanding the knowledge of our Universe. Here we report the highlights which have been achieved by the MAGIC collaboration since the beginning of the operations.

An algorithm is presented for a micro-model of a mining dump truck movement, which allows determining the optimal speed and acceleration of a vehicle, considering the change of the road grade. The structure of the simulation macro-model of an excavator-and-dump truck complex has been developed. The procedure for integrating a micro-model of a dump truck movement into a simulation model is shown. As a result of a series of experiments with a macro-model, the influence of open pit roads grade on the performance and efficiency of excavator-and-dump truck complexes was established. The necessity of considering in simulation excavator-and-dump truck complexes the speed regulation of dump trucks depending on the change in road grade is shown.

This pioneering study presents an in-depth biomechanical examination of soccer's diving header, aiming to quantify its impact on ball speed enhancement (BSE) and effective offensive range (EOR). Despite the diving header's widespread acclaim and historical significance, there remains a dearth of scientific scrutiny into its biomechanical intricacies. Employing an innovative research design featuring a static hanging ball at varied offensive distances and heights, the study replicates diverse header scenarios. The results of 3D motion quantification have shown that a physically excellent player (identified through the maximal standing long jump test) could reach an EOR around 2.64 times his body height. Furthermore, the study unveils that proficient players could attain BSE surpassing 9 m/s, signifying the diving header's heightened efficacy compared to traditional heading techniques, which could only result in 4.5 m/s. Correlation analyses unveil noteworthy relationships, highlighting the pivotal role of head speed at impact and the influence of minimizing speed-drop and temporal disparities for amplified effectiveness. Considerations for optimizing diving header execution are introduced, emphasizing the necessity for targeted training programs. Despite acknowledged limitations inherent to its pilot nature, this exploration furnishes foundational knowledge to guide subsequent research and practical applications, providing valuable insights into soccer training and skill development through a biomechanical lens.

We discuss how the interaction of electrons with an overdamped optical phonon can give rise to a strange-metal behavior over extended temperature and frequency ranges. Although the mode has a finite frequency, an increasing damping shifts spectral weight to progressively lower energies so that, despite the ultimate Fermi liquid character of the system at the lowest temperatures and frequencies, the transport and optical properties of the electron system mimic a marginal Fermi liquid behavior. Within this shrinking Fermi liquid scenario, we extensively investigate the electron self-energy in all frequency and temperature ranges, emphasizing similarities and differences with respect to the marginal Fermi liquid scenario.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

High-methoxyl apple pectin (AP) derived from apple was employed as the main ingredient facilitating rheological modification features for developing dysphagia-friendly fluidized alimentary matrices. Xanthan gum (XG) was also included as a composite counterpart to modify the viscoelastic properties of the thickened system under different thermal processes. The results indicate that AP is extremely sensitive to thermal processing, and the viscosity is greatly depleted under a neutral pH level. Moreover, the inclusion of calcium ions echoed a modification effect on the rheological properties of AP, and both the elastic property and viscosity value are promoted after thermal processing. The modification effect of viscoelastic properties (Gʹ and Gʹʹ) is observed while XG is incorporated into the composite formula. By promoting the XG ratio from 7: 3 to 6: 4 (AP: XG), it triggers the rheological transformation from a liquid-like form to a solid-like state, and the viscosity value shows that the AP-XG composite system exhibits better thermal stability after thermal processing. The ambient modifiers of pH (pH &lt; 4) and calcium chloride concentration (7.5%) with an optimal AP-XG ratio of 7:3 lead to weak-gel-like behavior (Gʹʹ &lt; Gʹ), helping to maintain the texture properties of dysphagia-friendly features similar to those prior to the thermal processing.

Leaf area estimation is a critical component in the study of plant growth and productivity within agricultural systems. This research introduces the LeafArea package, a specialized tool designed to calculate the leaf area of six distinct Andean fruit species: S. quitoense, S. betaceum, P. peruviana, R. fruticosus, P. ligularis and P. edulis. Leveraging response variables such as species type, leaf length and width, the package employs advanced machine learning algorithms to estimate leaf area accurately. The primary focus of the study is to identify the most effective model for describing the relationship between leaf width, length, and area for each plant species. Currently, the LeafArea package utilizes four different machine learning algorithms, namely generalized linear model (GLM), generalized linear mixed model (GLMM), Random Forest and XGBoost. Among these, XGBoost stands out as a top-performing algorithm, exhibiting exceptional predictive accuracy. The evaluation metrics employed in the program provide valuable insights for researchers, aiding in informed decision-making. Specifically, XGBoost demonstrates significantly lower prediction errors and approaches a near-perfect R2 value, emphasizing its potential to enhance predictive accuracy. These results underscore the efficacy of machine learning techniques, as a compelling choice for researchers seeking precise and robust predictions in leaf area estimation. The LeafArea package thus represents a valuable tool for advancing our understanding of plant growth dynamics, resource allocation, and overall productivity within agricultural ecosystems.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

Abstract: CRISPR/Cas systems are used for genome editing, both in basic science and in bio-technology. At the same time, CRISPR/Cas editors have several limitations, including insufficient specificity leading to "off-targets" and the dependence of activity on chromatin state. A number of highly specific Cas9 variants have been obtained now, but most of them are characterized by reduced activity on eukaryotic chromatin. We identified a spatial cluster of amino acid residues in the PAM-recognizing domain of Streptococcus pyogenes Cas9, whose mutations restore the activity of one of the highly specific forms of SpyCas9 without reducing its activity in Saccharomyces cere-visiae. In addition, one of these new mutations also increases the efficiency of SpyCas9-mediated editing of a site localized on the stable nucleosome. The improved Cas9 variants we obtained, which are capable of editing hard-to-reach regions of the yeast genome, may help in both basic research and yeast biotechnological applications.

The oxidative coupling of methane (OCM) to produce ethane and ethylene (C2 compounds) as platform chemicals involves complex chemistry with reactions both in the gas phase and on the catalyst surface, resulting in a distribution of products at the expense of C2 selectivity. This work uses experimental data from a variety of mixed metal oxides on supports at different reaction conditions (temperature, contact time, and reactant flow rates) to train a random forest regressor that predicts methane conversion and C2 selectivity (key performance indicators (KPIs)), and deploys it to locate optimal conditions that maximize C2 yield for a catalyst. Investigating the regressor interpretability via feature importance reveals that the choice of metals and support are crucial to C2 selectivity predictions, while the predictions of methane conversion are driven by the reaction conditions. The machine learning (ML) regressor is used as a surrogate to develop performance curves for each of the catalysts via a multi-objective optimization routine that seeks to maximize the KPIs in the decision space of reaction conditions, is seen to locate optimal conditions at which the maximum C2 yields for catalysts are predicted to be 15%, higher on average. Analyzing the catalysts in the space of their performance curves with respect to a popular OCM catalyst, Mn-Na2WO4/SiO2, reveals distinct patterns based on intrinsic properties of metals and supports. Further, the decision space with catalyst descriptors and reaction conditions is optimized for high C2 yields using the ML surrogate, in a static multi-objective optimization routine, and an adaptive Bayesian routine, where the latter was found to have a wider field focus in proposing catalyst formulations and conditions. Transition metal oxides on a variety of supports were proposed but not their lanthanide oxide counterparts.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Benveniste’s experiments – known in the lay press as the “water memory” phenomenon – are generally considered to be a closed case. However, the amount of data generated by twenty years of well-conducted experiments prevents closing the file so simply. An issue, which has been little highlighted so far, merits to be emphasized. Indeed, if Benveniste failed to persuade his peers of the value of his experiments, it was mainly because of a stumbling block, namely the difficulty of convincingly proving the causal relationship between the supposed cause (“informed water”) and the experimental outcomes in different biological models. To progress in the understanding of this phenomenon, we abandon the idea of any role of water in these experiments (“water memory” and its avatars). In other words, we assume that control and test conditions that were evaluated were all physically identical; only their respective designations (labels) differentiated them. As a consequence, labels (“controls” vs. “tests”) and the corresponding states of the biological system (no change vs. change) are independent variables. We show in this article how simple considerations based on probability theory allow to build a probability model where the order of measurements matters. This model provides an alternative explanation to Benveniste’s experiments where water plays no role and where the place of the experimenter is central.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

An approach based on the OpenFOAM library has been developed to solve a high-speed, multicomponent mixture of a reacting, compressible flow. This work presents comprehensive validation of the newly developed solver called compressibleCentralReactingFoam with different supersonic flows, including shocks, expansion waves, and turbulence-combustion interaction. The comparisons of the simulation results with experimental and computational data confirm the fidelity of this solver for problems involving multicomponent high-speed reactive flows. The gas dynamics of turbulence-chemistry interaction are modeled using a partially-stirred reactor formulation and provide promising results to better understand the complex physics involved in supersonic combustors. A time-scale analysis based on local Damköhler numbers reveals different regimes of turbulent combustion. In the core of the jet flow, the Damköhler number is relatively high indicating that the reaction time scale is smaller than the turbulent mixing time scale. This means that the combustion is controlled by turbulent mixing. In the shear layer, where the heat release rate and the scalar dissipation rate have the highest value, the flame is stabilized due to finite rate chemistry with small Damköhler numbers and a high fraction of fine structure. This solver allows three-dimensional gas dynamic simulation of high-speed multicomponent reactive flows relevant to practical combustion applications.