Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

Vehicle windshield wiper system increases the driving safety by contributing a clear shot viewing to the driver. In this paper, modelling, designing and simulation of a vehicle windshield wiper system with robust control theory is done successfully. H∞ loop shaping and robust pole placement controllers are used to improve the wiping speed by tracking a reference speed signals. The reference speed signals used in this paper are step and sine wave signals. Comparison of the H∞ loop shaping and robust pole placement controllers based on the two reference signals is done and convincing results have been obtained. Finally the comparative results prove the effectiveness of the proposed H∞ Loop Shaping controller to improve the wiping mechanism for the given two reference signals.

The structural performance of reinforced concrete relies heavily on the bond between reinforcement and concrete. In nonlinear finite element analyses, bond is either modelled by merged, also called perfect bond, or coincident with slip, also called bond-slip, approaches. Here, the performance of these two approaches for the modelling of failure of reinforced concrete was investigated using a damage-plasticity constitutive model in LS-DYNA. Firstly, the influence of element size on the response of tension-stiffening analyses with the two modelling approaches was investigated. Then, the results of the two approaches were compared for plain and fibre reinforced tension stiffening and a drop weight impact test. It was shown that only the coincident with slip approach provided mesh insensitive results. However, both approaches were capable of reproducing the overall response of the experiments in the form of load and displacements satisfactorily for the meshes used.

The aim of this study was to using a lignin based resin (LB) to improve the performance of the soy flour based adhesive. Soy flour (SF), polyamidoamine-epichlorohydrin (PAE), LB was used to develop a plywood adhesive. The solid content and viscosity of the adhesive, functional groups, thermo-stability, and crystallinity of the cured adhesive were characterized and the performance of the resultant adhesive was evaluated by fabricating three-ply plywood. Results showed using LB and PAE mixture to modify SF adhesive improves dry and wet bond strength by 66.3 and 184.2%. PAE contributed more for the wet bond strength improvement and the LB contributed more for the dry bond strength. The improvement was attributed to: 1) LB/PAE reacted with the functions of the soy protein and form a cross-linking network; 2) Polycondensation reaction between LB molecules further improved crosslinking density of the adhesive and formed a interpenetration structure with crosslinked protein; 3)The easy penetration of LB on wood surface and formed more interlock with wood. The denser structure created by LB and PAE mixture improved the thermal stability and decreased the crystallinity of cured adhesive. The usage of the LB and PAE mixture increased solid content by 35.5%, meanwhile, makes its viscosity acceptable for the industrial application.

The current work addresses the control of two-input two-output (TITO) Wood and Berry model of a binary distillation column. The controller design problem is formulated in terms of multivariable H_∞ control synthesis. The controller structure takes the form of simplest static output feedback (SOF) control. The controller synthesis is performed using a hybrid approach of blending linear matrix inequalities (LMI) and genetic algorithm (GA). The performance of the static output feedback controller is compared with three other controllers designed for Wood and Berry model available in the literature. The first simulation study is performed for the case of tracking a unit step command in the presence of a step change in output disturbance. A second simulation study is performed for rejecting a change in sinusoidal output disturbance.

The mechanistic pathway of TEMPO/I₂-mediated oxidative cyclization of N,N-diaryl amino alcohols 1 is investigated in this study. Based on our direct empirical experiments, three key intermediates (the aminium radical cation 3, the α-aminoalkyl radical 4, and the iminium 5), four kind reactive species (radical TEMPO, cationic TEMPO, TEMPO-I and iodo radical) and three kind pathways (1. SET/PCET mechanism, 2. HAT/1,6-H transfer mechanism, 3. Ionic mechanism) were assumed. Under the assumption, nine free energy diagrams are acquired through DFT calculation. From the comparison of the solution phase free energy, some possibility can be excluded and then the chosen plausible mechanisms are concretized with the more stable intermediate 7.

The Koka gold deposit is located in the Elababu shear zone between the Nakfa terrane and the Adobha Abiy terrane, NW Eritrea. Based on the paragenetic study two main stages of gold mineralization were identified in the Koka gold deposit: 1) an early stage of pyrite-chalcopyrite-sphalerite-galena-gold-quartz vein; and 2) a second stage of pyrite-quartz veins. NaCl-aqueous inclusions, CO2-rich inclusions, and three-phase CO₂-H₂O inclusions occur in the quartz veins at Koka. The ore-bearing quartz veins formed at 268℃, from NaCl-CO₂-H₂O(-CH₄) fluids averaging 5 wt% NaCl eq. The ore-forming mechanisms include fluid immiscibility during stage I, and mixing with meteoric water during stage II. Oxygen, hydrogen and carbon isotopes suggest that the ore-forming fluids originated as mixtures of metamorphic water, meteoric water and magmatic water, whereas sulfur isotope suggest an igneous origin. Features of geology and ore-forming fluid at Koka deposit are similar to those of orogenic gold deposits, suggesting the Koka deposit might be an orogenic gold deposit related to granite.

Geometallurgy has become an important toll to predict the process behavior of the ores, and to decrease the production risks cause by variability of geological settings. In this paper geometallurgical index for grinding properties of the ore has investigated. In a comprehensive research at Sarcheshmeh porphyry copper mine, geological features, what were supposed to affect the main process responses including product’s grade-recovery, and plant’s throughput, were subjected to investigate as the possible geometallurgical indexes. The rock breakage variability, in terms of a ball mill grinding circuit and its effects on the plant throughput and energy consumption are presented. Ninety samples were collected based on geological features including lithology, hydrothermal alteration, and geological structures. The samples were characterized using XRD, XRF, and electron and optical microscopy. A simulated test method for Bond ball mill work index (BWI) was used to perform the comminution test. The results showed BWI values vary from 5.67 kWh/t to 20.21 kWh/t. Examination of the possible correlations between BWI and the geological features showed that the key geological feature related to comminution variability is lithology. In addition, the hydrothermal alteration would be an effective parameter in the period that the plant is fed with a single lithology

The number of citations that a paper has received is the most commonly used indicator to measure the quality of research. Researchers, journals, and universities want to receive more citations for their scholarly publications to increase their h-index, impact factor, and ranking respectively. In this paper, we tried to analyses the effect of the number of available Google Scholar versions of a paper on citations count. We analyzed 10,162 papers which are published in Scopus database in year 2010 by Malaysian top five universities. Then we developed a software to collect the number of citations and versions of each paper from Google Scholar automatically. The result of spearman correlation coefficient revealed that there is positive significant association between the number of Google Scholar versions of a paper and the number of times a paper has been cited.

In this paper, a solenoid based linearly movable armature system is designed using robust control theory in order to improve the performance of the system. Reference track method is the best performance analysis for position control systems. Among the robust controllers, H infinity mixed-sensitivity and Mixed H 2 /H∞ with Regional Pole Placement Controllers are used to improve the performance of the system. Comparison of the proposed controllers for tracking a reference displacement signals (step and sine wave) and a promising simulation result have been obtained.

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

It is argued that if the non-unitary measurement transition, as codified by Von Neumann, is a real physical process, then the ‘probability assumption’ needed to derive the Second Law of Thermodynamics naturally enters at that point. The existence of a real, indeterministic physical process underlying the measurement transition would therefore provide an ontological basis for Boltzmann’s Stosszahlansatz and thereby explain the unidirectional increase of entropy against a backdrop of otherwise time-reversible laws. It is noted that the Transactional Interpretation (TI) of quantum mechanics provides such a physical account of the non-unitary measurement transition, and TI is brought to bear in finding a physically complete, non-ad hoc grounding for the Second Law.

In this paper a full state feedback control of a double inverted pendulum on a cart (DIPC) are designed and compared. Modeling is based on Euler-Lagrange equations derived by specifying a Lagrangian, difference between kinetic and potential energy of the DIPC system. A full state feedback control with H infinity and H 2 is addressed. Two approaches are tested: open loop impulse response and a double inverted pendulum on a cart with full state feedback H infinity and H 2 controllers. Simulations reveal superior performance of the double inverted pendulum on a cart with full state feedback H infinity controller.

In this work, we introduce the class of h-MN-convex functions by generalizing the concept of MN-convexity and combining it with h-convexity. Namely, let M : [0, 1] → [a, b] be a Mean function given by M (t) = M (t; a, b); where by M (t; a, b) we mean one of the following functions: A_t (a, b) := (1 − t) a + tb, G_t (a, b) = a^1−tb^t and H_t (a, b) := $\frac{ab}{ta+\left(1-t\right)b}=\frac{1}{A_t\left(\frac{1}{a},\frac{1}{b}\right)}$ with the property that M (0; a, b) = a and M (1; a, b) = b. Let I, J be two intervals subset of (0, ∞) such that (0, 1) ⊆ J and [a, b] ⊆ I. Consider a non-negative function h : J → (0, ∞), a function f : I → (0, ∞) is said to be h-MN-convex (concave) if the inequality f (M (t; x, y)) ≤ (≥) N (h(t); f (x), f (y)), holds for all x, y ∈ I and t ∈ [0, 1]. In this way, nine classes of h-MN-convex functions are established, and therefore some analytic properties for each class of functions are explored and investigated. Characterizations of each type are given. Various Jensen’s type inequalities and their converses are proved.

The research paper presents a new approach towards constructing motion equations for structures with attached MTMDs (multiple tuned mass dampers). A primary system, with MDOF (multiple dynamic degrees of freedom) was reduced to an equivalent system with a SDOF (single degree of freedom) through the modal approach, and equations from additional MTMDs were added to a thus-created system. Optimization based on H2 and H∞ for the transfer function associated with the generalized displacement of an SDOF system. The research work utilized GA (genetic algorithms) and SA (simulated annealing method) optimization algorithms to determine the stiffness and damping parameters for individual TMDs. The effect of damping and stiffness (MTMD tuning) distribution depending on the number of TMDs was also analyzed. The paper also reviews the impact of primary system mass change on the efficiency of optimized MTMDs, as well as confirms the results of other authors involving greater MTMD effectiveness relative to a single TMD.

Materials design for processing and application requires fundamental understanding of their properties based interatomic interaction. The use of the novel concept of total bond order density (TBOD) as a single quantum mechanical metric to characterize the internal cohesion of a crystal and correlate with the calculated physical properties is particularly appealing. This requires detailed first-principles calculation of the electronic structure, interatomic bonding and related properties. In this article, we use this new concept and apply it to chalcogenide crystals based on data obtained from 25 crystals: Ag₂S, Ag₂Se, Ag₂Te, As₂S₃, As₂Se₃, As₂Te₃, As₄Se₄, Cu₂S, Cu₂Se, Cu₂Te, Cu₄GeS₄, Cu₂SnS₃, Cu₂SnSe₃, GeS₂, GeSe₂, Ge₄Se₉, Sb₂S₃, Sb₂Se₃, Sb₂Te₃, SnS, SnSe, CdSe, CdTe, ZnSe, and ZnTe. Together with the calculated optical and mechanical properties, we demonstrate the efficacy of using this novel approach for materials design that could facilitate the exploration and development of new chalcogenide crystals and glasses. Moreover, the TBOD and its partial components (PBOD) could be the key descriptors in machine learning protocol for broader scale design when a large database is available.

Atoms in Molecules (AIM), Natural Bond Orbital (NBO), and normal coordinate analysis have been carried out at the global minimum structures of TH₅⁺ (T = C/Si/Ge). All these analyses lead to a consistent structure for these three protonated TH₄ molecules. The CH₅⁺ has a structure with three short and two long C-H covalent bonds and no H-H bond. Hence, the popular characterization of protonated methane as a weakly bound CH₃⁺ and H₂ is inconsistent with these results. However, SiH₅⁺ and GeH₅⁺ are both indeed a complex formed between TH₃⁺ and H₂ stabilized by a tetrel bond, with the H₂ being the tetrel bond acceptor. The three-center-two-electron bond (3c-2e) in CH₅⁺ has an open structure, which can be characterized as a V-type 3c-2e bond and that found in SiH₅⁺ and GeH₅⁺ is a T-type 3c-2e bond. This difference could be understood based on the typical C-H, Si-H, Ge-H and H-H bond energies. Moreover, this structural difference observed in TH₅⁺ can explain the trend in proton affinity of TH₄. Carbon is selective in forming a ‘tetrel bond’ and when it does, it might be worthwhile to highlight it as a ‘carbon bond’.

In this paper, modelling designing and simulation of a Ward Leonard layout system is done using robust control theory. In order to increase the performance of the Ward Leonard layout system with H infinity optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers are used. The open loop response of the Ward Leonard layout system shows that the system needs to be improved. Comparison of the Ward Leonard layout system with H∞ optimal control synthesis and H infinity optimal control synthesis via gamma-iteration controllers to track a desired step speed input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed Ward Leonard layout system with H infinity optimal control synthesis controller in improving the percentage overshoot and the settling time.

Amorphous solid dispersions are considered a promising formulation strategy for the oral delivery of poorly soluble drugs. The limiting factor for the applicability of this approach is the physical (in)stability of the amorphous phase in solid samples. Minimizing the risk of reduced shelf life for a new drug by establishing a suitable excipient/polymer-type from first principles would be desirable to accelerate formulation development. Here we perform Molecular Dynamics simulations to determine properties of blends of eight different polymer-small molecule drug combinations for which stability data is available from a consistent set of literature data. We calculate thermodynamic factors (mixing energies) as well as mobilities (diffusion rates and roto-vibrational fluctuations). We find that either of the two factors, mobility and energetics, can determine the relative stability of the amorphous form for a given drug. Which factor is rate limiting depends on physico-chemical properties of the drug and the excipients/polymers. The methods outlined here can be readily employed for an in-silico pre-screening of different excipients for a given drug to establish a qualitative ranking of the expected relative stabilities, thereby accelerating and streamlining formulation development.

Morphogenesis remains a riddle, wrapped in a mystery, inside an enigma. It remains a formidable problem viewed from many different perspectives of morphology, genetics, and computational modelling. We propose a biochemical reductionist approach that shows how both internal and external physical forces contribute to plant morphogenesis via mechanical stress-strain transduction from the primary cell wall tethered to the plasma membrane by a specific arabinogalactan protein (AGP). The resulting stress vector with direction defined by Hechtian adhesion sites, has a magnitude of a few picoNewtons amplified by a hypothetical Hechtian growth oscillator. This paradigm shift involves stress activated plasma membrane Ca2+channels and auxin-activated H+-ATPase. The proton pump dissociates periplasmic AGP-glycomodules that bind Ca2+. Thus, as the immediate source of cytosolic Ca2+ an AGP-Ca2+ capacitor directs vectorial exocytosis of cell wall precursors and auxin efflux (PIN) proteins. In toto these components comprise the Hechtian Oscillator and also the gravisensor. Thus interdependent auxin and Ca2+ morphogen gradients account for the predominance of AGPs. The size and location of a cell surface AGP-Ca2+ capacitor is essential to differentiation and explains AGP correlation with all stages of morphogenetic patterning from embryogenesis to root and shoot. Finally, evolutionary origins of the Hechtian Oscillator in the unicellular Chlorophycean algae reflect the ubiquitous role of chemiosmotic proton pumps that preceded DNA at the dawn of life.

A series of MgAl-layered double hydroxide (MgAl-HT), the calcined form at 500^oC (MgAlO_x) and the re-hydrated one at 25^oC (MgAl-HT-RH) were synthesized. Physicochemical properties of the catalysts were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM). Surface area of the as-synthesized, calcined and re-hydrated catalysts was determined by N₂ physisorption at -196^oC. CO₂-teperature programmed desorption (CO₂-TPD) was applied to determine the basic sites of catalysts. The catalytic test reaction was carried out using benzaldehyde and their derivatives with nitromethane and their derivatives. The Henry products (1-15) were obtained in a very good yield using MgAl-HT-RH catalyst either by conventional method at 90^oC in liquid phase, or under microwave irradiation method. The mesoporous structure and basic nature of re-hydrated solid catalyst were responsible for their superior catalytic efficiency. The robust nature was determined by using the same catalyst for five times, where the product % yield was almost unchanged significantly.

In this work, several inequalities of Popoviciu type for h-MN-convex functions are proved, where M and N are denote to Arithmetic, Geometric and Harmonic means and h is a non-negative superadditive or subadditive function.

To date, Cartesian (x, y, z) coordinate system (CCS) has been the default approach to geometrically specify atomic spatial positions in protein structures since the launch of Protein Data Bank (PDB) in 1971. To this end, this paper proposes a local spherical coordinate system (SCS) approach as an alternative to the default approach and a previously reported global SCS approach. The local SCS approach here requires only two parameters (θ and φ), instead of x, y and z as required by the default CCS approach. Essentially, CCS and SCS are like the two sides of one coin, i.e., geometric coordinate system for three-dimensional position specification. Therefore, this paper furthermore argues that it is time to flip the coin over, and have a look at the other side of the coin, e.g., the local SCS approach, which possesses an intrinsically lower degree of descriptional complexity than that of the default CCS approach, and constitutes a potentially useful alternative perspective for all protein structural research field.

A Zn(II) perchlorate complex has been prepared and characterized by single X-ray crystallography, nuclear magnetic resonance spectroscopy, thermogravimetric analysis, infrared spectroscopy, elemental analysis, and UV-vis spectroscopy. The complex crystallizes in the monoclinic space group P21/c (Z = 4) with a pentacoordinated zinc center. Interestingly, the Zn complex was found be to a potential fluorophore that could sense acetone and other ketones with high selectivity and sensitivity.

In this paper we investigate the optimal investment strategy for a defined contribution (DC) pension plan during the decumulation phrase which is risk-averse and pays close attention to inflation risk. The plan aims to maximize the expected constant relative risk aversion (CRRA) utility from the terminal wealth by investing the wealth in a financial market consisting of an inflation-indexed bond, an ordinary zero coupon bond and a risk-free asset. We derive the optimal investment strategy in closed-form using the dynamic programming approach by solving the corresponding Hamilton-Jacobi-Bellman (HJB) equation. Our theoretical and numerical results reveal that under some rational assumptions, an inflation-indexed bond do has significant advantage to hedge inflation risk.

The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

Theoretical approaches to calculate pKa values for Brønsted acids is a challenging task that, most of the time, involves sophisticated and time-consuming methods. Therefore, heuristic approaches are efficient and appealing methodologies to approximate these values. Herein, by considering the electrostatic potential on acidic hydrogen atoms in a similar fashion that a σ–hole is defined, we calculated the maximum surface potential, V_S,max, and used it as a descriptor to correlate it with experimental acidity constants. These values were calculated using the CPCM implicit solvent model (water) with six different methods: five density functionals and the Møller–Plesset second order perturbation theory. Six different basis sets were combined with each method in order to benchmark a total of thirty-six levels of theory. Overall, 1080 calculations were performed and found to correlate with experimental data. The ωB97X-D/6-31+G(d,p) level of theory stands as the best one for consistently reproduce the reported pKa values.

It is always a difficult task to assign the peaks recorded from vibrational spectrum. Herein we explored a new pathway of density functional theory (DFT) simulation to present three kinds of spectra of ice XIV and can be referenced as inelastic neutron scattering (INS), IR, and Raman experimental spectrum. The INS spectrum is proportional to phonon density of states (PDOS) while the photon scattering signals reflect the normal vibration frequencies near the Brillouin zone (BZ) center. Based on good agreements with experimental data, we identified the relative frequency and made scientific assignments by normal vibration modes analysis. The debating two hydrogen bond (H-bond) peaks among ice phases from INS have been discussed and the dynamic process of H-bond vibrations were found to be classified into two basic modes. we deduce that two H-bond modes are a general rule among ice family and more works are ongoing to investigate this subject.

In this paper, modelling designing and simulation of a simple voltage amplidyne system is done using robust control theory. In order to increase the performance of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers are used. The open loop response of the voltage amplidyne system shows that the system can amplify the input 7 times. Comparison of the voltage amplidyne system with H ∞ optimal control synthesis and H ∞ optimal control synthesis via ∞-iteration controllers to track a desired step input have been done. Finally, the comparative simulation results prove the effectiveness of the proposed voltage amplidyne system with H ∞ optimal control synthesis controller in improving the percentage overshoot and the settling time.

MP2/aug-cc-pVTZ calculations were carried out for the ZFH₃-B complexes (Z = C, Si, Ge, Sn and Pb; B = C₂H₂, C₂H₄, C₆H₆ and C₅H₅^-; relativistic effects were taken into account for Ge, Sn and Pb elements). These calculations are supported by other approaches; the decomposition of the energy of interaction, Quantum Theory of Atoms in Molecules (QTAIM) and Natural Bond Orbital (NBO) method. The results show that tetrel bonds with π-electrons as Lewis bases are classified as Z…C links between single centers (C is an atom of the π-electron system) or as Z…π interactions where F-Z bond is directed to the mid-point (or nearly so) of the CC bond of the Lewis base. The analogues systems with Z…C/π interactions were found in the Cambridge Structural Database (CSD). It was found that the strength of interaction increases with the increase of the atomic number of the tetrel element and that for heavier tetrel elements the ZFH₃ tetrahedral structure is more deformed towards the structure with the planar ZH₃ fragment. The results of calculations show that the tetrel bond is sometimes accompanied by the Z-H…C hydrogen bond or even sometimes the ZFH₃-B complexes are linked only by the hydrogen bond interaction.

This article aims to solve the problem of robust supervision of a reverse osmosis desalination system (RO-DS) with two models, external model and bond graph model. The structure of an industrial system from the point of view of the external model operates according to several modes of operation (degraded and normal). For this external model, we cannot locate the faults since we are talking about a global operation of the system. The possible solution for the development of research was to use the multidisciplinary model called bond graph. This model by its graphic nature and using a unified language makes it possible to model the industrial system element by element from where it helps the user not only to detect the faults but also to locate them when they appear in the system. The results suggest that the use of the bond graph model for alarm 02 is a reverse osmosis error (RO1); these phenomena are readable on the bond graph model and can be quantified by equations. The equation of the model of this reverse osmosis (RO1) is found in the residual equations (r5, r6 and r7), so that these residues will be sensitive to this rupture. The possible solution during research development was to use the bond graph model to supplement information with physical knowledge and to locate faults. This article also describes the operating safety (by minimizing false alarms and non-detections as well as delays in fault detection) of the desalination system by using the bond graph model described in Linear Fractional Transformation (LFT) form for enable it to manage the robust supervision of a desalination system. An approach based on (LFT-BG) is developed to monitor tank leakage (Cu) and reverse osmosis (RO1 and RO2) faults or valve level (V1 and V2) closures and membrane clogging reverse osmosis (Rm1 and Rm2) that can occur in the reverse osmosis desalination system (RO-DS).

In this paper we obtain some inequalities of Hermite-Hadamard type for composite convex functions. Applications for AG, AH-h-convex functions, GA, GG, GH-h-convex functions and HA, HG, HH-h-convex function are given.

Formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions is concerned as secondary minerals after alkaline alteration of bentonite in a repository of radioactive wastes. It might be crucial for safety assessment whether smectite will be formed or not as secondary minerals after alkaline alteration of bentonite. In present paper, Fe- and Mg-rich smectite which are currently interacting with hyperalkaline groundwater was found at Narra in Palawan, Philippines. Mineralogical and geochemical investigation was conducted to understand formation process of smectite and factors determined secondary mineral species. Our study revealed a certain amount of smectite may have been produced under hyperalkaline conditions, altered from amorphous or poorly crystalline material such as M-S-H and F-S-H. Key factor which decides smectite or zeolite as secondary minerals after alkaline alteration of bentonite might be whether nuclei of M-S-H and/or F-S-H will be formed or not. This might be decided by the presence of dissolved Mg2+ and Fe2+ in the system. Our suggested formation process of smectite under alkaline conditions is analogue with generally-accepted model of smectite formation that might have been occurred on early Mars.

The details of antigen-antibody interactions and the identification of epitopes are critical for the development of monoclonal antibody drugs. Ab42 is a native human-derived anti-CFH monoclonal antibody. In this study, the interaction between antigen pCFH and antibody (Ab42) was theoretically demonstrated by molecular docking and MD simulation, combined with free energy calculation and computational alanine scanning (CAS), and key amino acids and epitopes were identified. Experimental alanine scanning (EAS) was then carried out to verify the results of the calculation, and our results indicated that Ab42 antibody forms hydrogen bonds and interacts hydrophobically with pCFH through the Tyr315, Ser100, Gly33, and Tyr53 residues on its CDR, while the main pCFH epitopes are located at the six sites of Pro441, Ile442, Asp443, Asn444, Ile447, and Thr448. In conclusion, this study has explored the mechanism of antigen-antibody interaction from both theoretical and experimental aspects, and our results have important theoretical significance for the design and development of relevant antibody drugs.

Increased traffic in combination with growing environmental impacts, have led to accelerated degradation of the built infrastructure. In reinforced concrete structures, the corrosion of steel reinforcement is the predominant cause of deterioration. Thus, over the last years the use of glass fiber reinforced polymer (GFRP) composites as internal reinforcement bars (rebars) for concrete structures was evaluated, and has been proved to be a viable alternative to traditional steel reinforcement mainly due to its tensile strength and non-corrosive nature. However, thus far, the GFRP rebar market is diverse and manufacturers around the world produce GFRP rebar types with different surface enhancement to improve the bond to concrete characteristics. In this study, the bond performance of three dissimilar GFRP rebar types (sand coated, helically grooved and with surface lugs) was evaluated over time in seawater environments, with a focus on the bond strength. Accordingly, specimens were expose to seawater in circulating chambers, at three different temperatures (23 °C, 40 °C and 60 °C) for multiple time periods (60 and 120 days). To evaluate the bond performance, pullout tests were conducted according to ASTM D7913 [1]. The results showed that the bond strength varies with surface enhancement features. However, the bond strength didn’t vary significantly with exposure time and temperature for all three evaluated rebar types.

Carbon fiber reinforced polymer (CFRP) has been used widely in strengthening of steel structures. Steel/CFRP systems subjected to elevated temperatures is realistic in a summer climate event in many countries where the temperature in steel may approach 50 °C or even higher, which will lead to the degradation of the bond performance between CFRP and steel. Therefore, predicting the bond behavior of the CFRP/steel system under elevated temperature is critical. This paper investigated the mechanical performance of CFRP/steel adhesively-bonded double strap joints at elevated temperatures. Thirty CFRP-steel double strap joints were tested to failure under temperatures between 10 °C and 90 °C. It was found that the joint failure mode changed from adherend failure to debonding failure as the temperature approached T_g. In addition, the ultimate load and joint stiffness decreased significantly at temperatures near to and greater than T_g. Based on the experimental results, a model is proposed to predict the bond stress of the CFRP/steel at different temperatures.

This work demonstrates that a plasmid can function as an efficient biocatalyst in mediating the nitroaldol (Henry) reaction at high temperatures in ultrapure water. Compared with ssDNA, the plasmid displayed a remarkable catalytic efficiency (97% yield within 20 min). Aromatic aldehydes which bear strong or moderate electron-withdrawing groups reacted satisfactorily with nitromethane, which afforded the corresponding β-nitroalcohols in good yields within 2 h (up to 98%). By contrast, aliphatic and aromatic aldehydes with electron-donating groups did not react. Moreover, the yield significantly dropped when the size of the carbanion increased, and the yield was only 10% when nitropropane was used as the donor.

Rotavirus species H (RVH) has been detected in pigs, humans and bats. Moreover, porcine RVHs have been recently identified in several swine-producing countries. Despite their zoonotic impact, genome information of RVHs is still limited. This study aimed to establish a tentative complete genome-based genotyping system for RVHs, by appending genomic sequences from 12 porcine RVHs identified in Japan between 2013 and 2015 to those from human and other porcine RVHs reported in previous studies. Phylogenetic analysis of 11 RNA segments indicated that porcine RVHs could be classified into multiple genotypes. Consequently, the genotype classification for RVHs revealed the existence of genotypes 10G, 6P, 6I, 3R, 4C, 7M, 6A, 2N, 4T, 6E, 3H for the genes VP7, VP4, VP6, VP1, VP2, VP3, NSP1, NSP2, NSP3, NSP4 and NSP5, respectively. Surprisingly, two distinctive types in NSP1 and NSP3 genes were identified from among the twelve porcine RVHs. Our data suggest a potentially novel gene rearrangement event between porcine RVH and rotavirus species C in the NSP3 gene. These findings would provide a new insight in understanding for evolution of RV.

A brand-new approach to the understanding of breast cancer (BC) is urgently needed. In this contribution, the etiology, pathogenesis, and treatment of this disease is approached from the new pH-centric anticancer paradigm. Only this Unitarian perspective based upon that the hydrogen ion (H+) dynamics of cancer, allows understanding and integrating the many dualisms, confusions, and paradoxes of the disease. The new H+-related wide range model can embrace under a unique frame of mind the many aspects of the disease and at the same time therapeutically interfere with most, if not with all, the hallmarks of cancer known to date. The pH-related armamentarium available for the treatment of BC here reviewed may be beneficial for all types and stages of the disease. In this vein, we have attempted a mega synthesis of traditional and new knowledge in the different areas of breast cancer research and treatment based upon the wide range approach afforded by the hydrogen ion dynamics of cancer. The concerted utilization of a pH-related drugs nowadays available for the treatment of breast cancer is advanced.

Animal-assisted interventions (AAI) use human-animal interactions to positive effect in various contexts including cancer care. This systematic literature review is the first part of a two-part paper series focusing on the research methods and quantitative results of AAI studies in oncology. We find methodological consistency in the use of canines as therapy animals, in the types of high-risk patients excluded from studies, and in the infection precautions taken with therapy animals throughout cancer wards. The investigated patient endpoints are not significantly affected by AAI, with the exceptions of improvements in oxygen consumption, quality of life, depression, mood, and satisfaction with therapy. The AAI field in oncology has progressed significantly since its inception and has great potential to positively impact future patient outcomes. To advance the field, AAI research in oncology should consistently improve the methodological design of studies, report data more completely, and focus on the therapy animal’s well-being.

Infections contribute to carcinogenesis through inflammation-related mechanisms. It is well established that H. pylori infection is an etiological factor in gastric carcinogenesis. However, the mechanism through which H. pylori infection contributes to the development of gastric cancer has not been fully elucidated. H. pylori-associated chronic inflammation is linked to genomic instability via reactive oxygen and nitrogen species (RONS). In this article, we summarize the current knowledge of H. pylori-induced double strand breaks (DSBs). Further, we will provide mechanistic insight into how processing of oxidative DNA damage via base excision repair (BER) leads to double strand breaks (DSBs). We review the recent progress how H. pylori infection triggers NF-kB /iNOS versus NF-kB/nucleotide excision repair (NER) axis mediated DSBs to drive genomic instability. Taken together, this review discusses current findings related to DSBs and their implications for the mechanisms of DSB repair.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

Recently, the properties of bouncing oil droplets, also known as `walkers', have attracted much attention because they are thought to offer a gateway to a better understanding of quantum behaviour. They indeed constitute a macroscopic realization of wave-particle duality, in the sense that their trajectories are guided by a self-generated surrounding wave. The aim of this paper is to try to describe walker phenomenology in terms of de Broglie-Bohm dynamics and of a stochastic version thereof. In particular, we first study how a stochastic modification of the de Broglie pilot-wave theory, à la Nelson, affects the process of relaxation to quantum equilibrium, and we prove an H-theorem for the relaxation to quantum equilibrium under Nelson-type dynamics. We then compare the onset of equilibrium in the stochastic and the de Broglie-Bohm approaches and we propose some simple experiments by which one can test the applicability of our theory to the context of bouncing oil droplets. Finally, we compare our theory to actual observations of walker behavior in a 2D harmonic potential well.

In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

Within an Internet of Multimedia Things, the risk of disclosing streamed video content, such as arising from video surveillance, is of heightened concern. This leads to the encryption of that content. To reduce the overhead and lack of flexibility arising from full encryption of the content, a good number of selective-encryption algorithms have been proposed in the last decade. Some of them have limitations, in terms of significant delay due to computational cost, or excess memory utilization, or, despite being energy efficient, do not provide a satisfactory level of confidentiality, due to their simplicity. To address such issues, this paper presents a lightweight selective encryption scheme, in which encoder syntax elements are encrypted with the innovative EXPer (EXtended Permutation with exclusive OR). The selected syntax elements are taken from the final stage of video encoding that is during entropy coding. As a diagnostic tool, the Encryption Space Ratio measures encoding complexity of the video relative to the level of encryption so as to judge the success of the encryption process, according to entropy coder. A detailed comparative analysis of EXPer with state-of-the-art algorithms confirms that the EXPer provides significant confidentiality with a small computational cost and negligible encryption bitrate overhead. Thus, the results demonstrate that the proposed security scheme is a suitable choice for constrained devices in an Internet of Multimedia Things environment.

A series of penta-1,4-dien-3-one containing a H-phosphonate scaffold were designed and synthesized. The structures of all title compounds were determined by 1H-NMR, 13C-NMR, 31P-NMR, and HRMS. Bioassay results showed that several of the title compounds exhibited remarkable antibacterial and antiviral activities. Among these, compounds 3c and 3o exhibited substantial antibacterial activities against Xanthomonas oryzae pv. Oryzae (Xoo) and Xanthomonas axonopodis pv. citri (Xac). In addition, compounds 3c, 3f, and 3r showed remarkable curative activities against tobacco mosaic virus (TMV), with 50% effective concentration (EC50) values of 290.0, 234.0, and 373.6 μg/mL, respectively. These were superior to that of ningnanmycin (386.2 μg/mL). Compound 3r exhibited comparative protective activity against TMV, with an EC50 value of 291.1 μg/mL, which was better than that of ningnanmycin (297.1 μg/mL). Notably, the solubility of all title compounds improved relative to the lead compound curcumin. These results suggest that penta-1,4-dien-3-one containing a H-phosphonate scaffold may be considered as an activator for antibacterial and antiviral agents.

In recent years, an interest in multimedia services has grown expeditiously where the main part is comprised of video. Firms as well as subscribers require higher resolutions, framerates and sampling precision which results to higher amount of data need for processing, storing and transmitting. Therefore, a big challenge arises for researchers to develop new compression standards which should reduce the huge amount of data and keep quality at the same level. This paper examines compression performance of the latest and currently most used video codecs, namely H.266/VVC, AV1, H265/HEVC and H.264/AVC. The test set consists of seven sequences with various content at 8K, Ultra HD and Full HD resolution and encoded to bitrates from 1 to 15 Mbps for Full HD and Ultra HD resolutions and from 5 to 50 Mbps for 8K resolution, respectively. Codec performance was measured using PSNR, SSIM and VMAF objective quality metrics. In terms of the Bjøntegaard-Delta (BD) model, the results showed that H.266/VVC outperforms all other codecs, namely H.264/AVC,H.265/HEVC and AV1, respectively. Averaged bitrate savings were approximately 78\% for H.266/VVC, 63\% for AV1 and 53\% for H.265/HEVC relative to H.264/AVC, 59\% for H.266/VVC, 22\% for AV1 compared to H.264/AVC and 46\% for H.266/VVC relative to AV1, all for 8K resolution. The results also showed that the performance varies depending on resolution – with higher resolution, the efficiency of newly developed codecs such as H.266/VVC and AV1 is greater, which confirmed the fact that the H.266/VVC and AV1 codecs have been primarily developed for videos at high resolutions as 8K and/or UHD.

Lead, known as a metal with high neurotoxicity to children, cadmium, which is a carcinogenic and bioaccumulative contaminant, and arsenic, a class 1 carcinogenic according to the International Agency for Research on Cancer, are toxic elements (TEs) whose relevant route of exposure may be diet. We determined the bio-accessible fraction of lead, cadmium, and arsenic from the diet of preschool children from two day care centers (DCC). A cross-sectional study was conducted with 64 one–four-year-old children from two DCCs where the 24-h duplicate diet samples were collected. The diet samples were analyzed by ICP-MS for lead, cadmium, and arsenic total concentrations (n = 64) and their bio-accessibility were analyzed for a subsample (n = 10). The dietary intake (DI) mean for lead, cadmium, and arsenic were 0.18 ± 0.11 µg kg⁻¹ bw, 0.08 ± 0.04 µg kg⁻¹ bw, and 0.61 ± 0.41 µg kg⁻¹ bw, respectively. All DI calculated for TEs, considering total intake, were found lower than the tolerable limits (TL) (European Union, or World Health Organization, WHO, when applicable) except for one child’s Pb intake. Bio-accessibilities ranged between 0% to 93%, 0% to 103%, and 0% to 69%, for lead, cadmium, and arsenic, respectively. Although DI for TEs has been found lower than TL, these reference values have been recently decreased or withdrawn since it was for lead and arsenic whose TL were withdrawn by WHO.

Flaviviruses replicate in membranous factories associated with the endoplasmic reticulum (ER). Significant levels of flavivirus polyprotein integration contribute to ER stress and the host cell may exhibit an Unfolded Protein Response (UPR) to this protein accumulation, stimulating appropriate cellular responses such as adaptation, autophagy or cell death. These different stress responses support other antiviral strategies initiated by infected cells and can help to overcome viral infection. In epithelial A549 cells, a model currently used to study the flavivirus infection cycle and the host cell responses, all three pathways leading to UPR are activated during infection by Dengue virus (DENV), Yellow Fever virus (YFV) or West Nile virus (WNV). In the present study, we investigated the capacity of ZIKA virus (ZIKV) to induce ER stress in A549 cells. We observed that the cells respond to ZIKV infection by implementing an UPR through activation of the IRE1 and PERK pathway without activation of the ATF6 branch. By modulating the ER stress response, we found that UPR inducers significantly inhibit ZIKV replication. Interestingly, our findings provide evidence that ZIKV could manipulate the UPR to escape this host cell defence system. Since incomplete UPR could lead to unresolved and persistent ER stress, we found that ZIKV infection was associated with an abnormal accumulation of viral envelope proteins, which were aggregated with non-native disulfide bridges. As the presence of these “amyloid like” protein polymers may be cytopathic, our observations provide new insights into specific neuropathologies associated with ZIKA virus infections.

Cotton is one of the most important economic crops in the world, whereas insect attacks is a prime cause of its losses on yield and quality. Despite it is important, little is known about the mechanism of cotton response to insect. In this study, we simulated insect feeding by applying insect oral secretions (OS) to wounds, and combined transcriptome and metabolome analysis to comprehensively investigate how OS from two major pest species (Helicoverpa armigera and Spodoptera litura) affect cotton defense responses. Obvious differences were observed that 12,668 and 13,379 genes differently expressed respectively in cotton after being treated with different OS when compared with wounding along. Upon the addition of OS, JA-signaling pathway were rapidly and strongly induced, however SA-biosynthesis related gens were significantly down-regulated. By constructing the co-expression gene network, we identified a hub gene which encoding a leucine-rich repeat receptor kinase may play important role in recognition and signal transduction at early stage. We also found that OS from different insect species altered abundance of flavonoid related compound with different patterns. Interestingly, Gossypol which is a well-known anti-insect compound was kept a relative low content after OS application relative to wounding which implied the existence of the suppression effects of OS to cotton defense response. This study illustrated the transcriptional and metabolic changes of cotton in responding to OS from two chewing insect species, identified potential key gene during the interaction process and finds the evidence for OS’s inhibition effects on cotton defense response.

Hippophae is a tree species with ecological, economic and social benefits. In this study, we assembled and annotated chloroplast genomes of sympatric Hippophae gyantsensis and H. rhamnoides subsp. yunnanensis. Their full-length are 155260 and 156415 bp, respectively. Each of them has 131 genes, comprising 85 protein-coding genes, 8 ribosomal RNA genes and 38 transfer RNA genes. After comparing the chloroplast genomes, we found 1302 base difference loci, and 63.29% are located in the intergenic region or intron sequences and 36.71% are located in the coding sequences. The SSC region has the highest mutation rate, followed by the LSC region; the IR regions have the lowest mutation rate. Among the protein-coding genes, three had a ratio of nonsynonymous to synonymous substitutions (Ka/Ks) >1 (but P values were non-significant) and 66 had Ka/Ks <1 (46 were significant). In general, the chloroplast protein-coding genes may be subject to purification selection. Among H. gyantsensis and H. rhamnoides subsp. yunnanensis chloroplast protein-coding genes, there are 20 and 16 optimal codons, respectively. Most of the optimal codons were ending with A or U, which indicates significant AT preference. It is an important reference for studies on the general characteristics and evolution of the Hippophae chloroplast genome.

Antisense technologies consist of the utilization of oligonucleotides or oligonucleotide analogs to interfere with undesirable biological processes, commonly through inhibition of expression of selected genes. This field holds a lot of promise for the treatment of a very diverse group of diseases including viral and bacterial infections, genetic disorders, and cancer. To date, drugs approved for utilization in clinics or in clinical trials target diseases other than bacterial infections. Although several groups and companies are working on different strategies, the application of antisense technologies to prokaryotes still lags with respect to those that target other human diseases. In those cases where the focus is on bacterial pathogens, a subset of the research is dedicated to produce antisense compounds that silence or reduce expression of antibiotic resistance genes. Therefore, these compounds will be adjuvants administered with the antibiotic to which they reduce resistance levels. A varied group of oligonucleotide analogs like phosphorothioate or phosphorodiamidate morpholino residues, as well as peptide nucleic acids, locked nucleic acids and bridge nucleic acids, the latter two in gapmer configuration, have been utilized to reduce resistance levels. The major mechanisms of inhibition include eliciting cleavage of the target mRNA by the host’s RNase H or RNase P, and steric hindrance. The different approaches targeted resistance to β-lactams including carbapenems, aminoglycosides, chloramphenicol, macrolides, and fluoroquinolones.

The prim objective of commenced article is to determine q-sumudu transforms of a product of unified family of q-polynomials with basic (or q-) analogue of fox’s H-function and q-analog of I-functions. Specialized cases of the leading outcome are further evaluated as q-sumudu transform of general class of q-polynomials and q-sumudu transforms of the basic analogues of Fox’s H-function and I-functions.

The development of a stationary phase material for high performance liquid chromatography based on a surface of silica hydride as opposed to silanols on ordinary silica is discussed including synthetic approaches, characterization and applications. There are several synthetic approaches available to create a silica hydride surface. Modification of the Si-H moiety on the silica surface can be accomplished through use of a hydrosilation reaction. Both the intermediate silica hydride and the material modified with an organic moiety can be characterized by a number of spectroscopic as well as a variety of other methods. Further insights into the retention mechanism are provide through chromatographic measurements. The ultimate utility of any chromatographic stationary phase material is determined by its success for solving challenging analytical problems. A broad range of applications are reviewed to illustrate the versatility and usefulness of silica hydride-based stationary phases.

In the article, by applied the concept of strongly convex function and one known identity, we establish several Ostrowski type inequalities involving conformable fractional integrals. As applications, some new error estimations for the midpoint formula are provided as well.

Arabidopsis contains eight different h-type thioredoxins (Trx) being distributed in different cell organelles. Although Trx h2 is deemed to be localized in mitochondria, its subcellular localization and function remains a matter of debate. Here, Trx h2 localization and function were investigated using cell fractionation studies and reverse genetics. Differential centrifugation and immunodetection showed the Trx h2 protein to be distributed to the microsomal fraction rather than to mitochondrial preparations. To analyze whether Trx h2 has different roles than mitochondrial Trxs, Arabidopsis mutants lacking Trx h2 were compared with mutants deficient in mitochondrial Trx o1 and double mutants with joint deficiencies in both Trxs. Under constant medium light, trxh2 grew as the wild type, while trxo1 and trxo1h2 mutants showed impaired growth. This was accompanied by differences in the metabolite profiles. The trxo1 and trxo1h2 mutants clustered differently from the wild type during the night, revealing a decrease in ascorbate and glutathione redox states. In fluctuating light intensities, genotypic differences in growth rates were attenuated. Compared to the wild type, the fluctuating-light induced decrease in the NADPH/NADP ratio was diminished in the mutants, with the trxo1h2 double mutant showing the strongest effect. This was accompanied by an increase in the photosynthetic efficiency of the trxo1h2 mutant, specifically in the high light phases of fluctuating light. Conclusively, these results support the view that Trxs o1 and h2 are localized in different subcellular compartments, and have different effects on ascorbate and glutathione redox states and growth in medium light, but cooperatively affect NADP(H) redox state and photosynthetic efficiency in fluctuating light.

Quasicrystals are a class of ordered solids made of typical metallic atoms but they do not exhibit the physical properties usually signaling the presence of metallic bonding and their electrical and thermal transport properties resemble a more semiconductor-like than metallic character. In this paper I first review a number of experimental results and numerical simulations suggesting that the origin of the unusual properties of these compounds can be traced back to two main features. For one thing, we have the formation of covalent bonds among certain atoms grouped into clusters at a local scale. Thus, the nature of chemical bonding among certain constituent atoms should play a significant role in the onset of non-metallic physical properties of quasicrystals bearing transition-metal elements. On the other hand, the self-similar symmetry of the underlying structure gives rise to the presence of an extended chemical bonding network due to a hierarchical nesting of clusters. This novel structural design leads to the existence of quite diverse wave functions, whose transmission characteristics range from extended to almost localized ones. Finally, the potential of quasicrystals as thermoelectric materials is discussed on the basis of their specific transport properties.

Considerable attention has been given to the research field of bioorganometallic chemistry, which is a hybrid chemistry field between biology and organometallic chemistry. The introduction of biomolecules, which have hydrogen bonding sites and chiral centers, into organometallic compounds is considered to be a promising strategy to construct chirality-organized bioorganometallic conjugates. This feature paper sketches an outline of induction of helical chirality into bioorganometallic conjugates. Topics covered include control of the helical chirality of 1,n’-disubstituted ferrocene moieties in ferrocene-dipeptide conjugates and the chirality induction of the Au(I)–Au(I) axis in the dinuclear organogold(I)-uracil conjugates.

Understanding surfactant self-assembly in deep eutectic solvents (DES) is important to their potential use in industrial formulations. We have recently reported the formation of a fracto-eutectogel comprising SDS fractal aggregates at a concentration as low as 1.6 wt% in glyceline (a DES comprising glycerol and choline chloride) at room temperature. The building units of the fractals consisted of multilayers of self-assembled SDS lamellae arranged in a dendritic pattern. Here we report that this fractal phase transitions into a fluid phase above a critical gelation temperature, TCG ~ 45 oC, evident from polarized light microscopy (PLM) observations. Small-angle neutron scattering (SANS) reveals that this phase transition is underpinned by the nanoscopic morphological transformation of the SDS lamellae into cylindrical micelles at T &gt; TGC. Fitting SANS profiles confirms that the morphology of the micelles is SDS-concentration (cSDS) dependent at T &gt; TGC: cylindrical at cSDS &gt; 0.6 wt% and spherical at cSDS = 0.6 wt%. At cSDS &lt; 0.6 wt%, only isotropic scattering was observed in the SANS profiles. Such SDS self-assembly behaviors contrast with those we have previously observed in glycerol, which we attribute to the presence of ions (i.e. choline chloride) in glyceline. Our findings have general implications to surfactant self-assembly in DES, solvents that are rich in hydrogen bonding and ions.

In this paper, the design and analysis of coupled tank water level control system is done using robust control theory. The main aim of this work is to improve level controlling mechanisms in industries and household areas. In this paper, H ∞ and μ –synthesis controllers are designed to improve the level control system. The coupled tank water level control system is designed using the proposed controller’s comparison and tested for tracking a reference level signals (step, sine wave and random) and simulation results have been analyzed successfully. Finally the comparative simulation results prove the effectiveness of the proposed coupled tank water level control system with H ∞ controller for improving the tracking mechanism performance of the system.

Research with deuterium-depleted water (DDW) in the last two decades proved that deuterium/hydrogen ratio has a key role in cell cycle regulation and cellular metabolism. The present study aimed to investigate the possible effect of deuterium-depleted organic compounds (DDOC) alone and in combination with DDW on cancer growth in two in vivo mouse models. To produce DDOC, drinking water of laying hens was replaced with DDW (25 ppm) for 6 weeks, resulting in 60 ppm D level in dried egg yolk that was used as deuterium-depleted food additive. In one model, 4T1, a cell line with high metastatic capacity to the lung, was inoculated in the mice’s mammary pad. After three weeks of treatment with DDW and/or DDOC, the tumor volume in the lungs was smaller in all treated groups vs. controls with natural D level. Tumor growth and survival in mice transplanted with MCF-7 breast cancer cell line showed that the anticancer effect of DDW was enhanced by food containing the deuterium-depleted yolk. The study confirmed the importance of D/H ratio not only in consumed water but also in metabolic water produced by the mitochondria while oxidizing nutrient molecules. This is in line with the concept that initiation of cell growth requires the cells to generate a higher D/H ratio, but DDW, DDOC, or the naturally low-D lipids in a ketogenic diet, have significant effect on tumor growth by preventing the cells from raising D/H ratio to the threshold.

The one-to-one structural correspondence between any conjugated hydrocarbon CnHm and the borane BnHm+n is extended here, with the B3LYP/cc-pVDZ model, to pure conjugated carbon systems with the example of buckminsterfullerene C60 with the corresponding icosahedral isoelectronic system closo-borane B60H60, and the fluorine substituted systems B60F30H30 and B60F60 , all with icosahedral Ih symmetry. All systems correspond to energy minima in the potential energy hypersurface, except for B60(F30)in(H30)out . Selected electronic structure methods are used to characterize all systems: molecular electrostatic potentials (MEP), atomic charges, bond orders, and topological properties of the electron density within quantum theory of atoms-in-molecules (QTAIM) and electron-localization function (ELF) theory. In the particular case of B60H60 we use the recently developed Hückeloid model to characterize this system. The stability of the energy minimum icosahedral structure B60F60 could have an origin in F···F attractive interactions of the inner fluorine atoms of the cage.

Dentin bonding is a key in restorative dentistry. Herein, we developed self-etching two-bottle adhesive system containing 10-methacryloyloxidecyl dihydrogen phosphate monomer (MDP) and the physical, mechanical, and biocompatible properties were evaluated. The characteristics of MDP were analyzed using nuclear magnetic resonance (NMR). The water sorption and solubility, the shear-bond strengths to dentin and enamel, and cytotoxicity tests were performed. The newly blended experimental group showed the lowest thickness and water sorption and solubility values. The shear bond strength to enamel and dentin were comparable to control groups (the three other products) all test groups showed 60% of cell viability. In this study, the properties of the newly synthesized adhesive are comparable with the others. The fundamental goal of this study is to get the MDP patent released, as it is intended for domestic production. For this purpose, this dentin adhesive was developed and compared with the commercial product.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

This study identifies new Alkali Activated Composite Mud Mortar to alternate Cement Mortar used for laying masonry works. This study handles both experimental and numerical analysis of strength and durability for mortar, especially bond strength along mortar and brick joints have studied detail and compared with ANSYS. The bond strength has estimated through the triplet brick prism of shear behavior. The strength and deformation characteristics of masonry constituents obtained from these tests depend on the actual composite conduct of masonry. There is always a good reception for environmentally friendly, low energy, new construction materials, and used in preparing mortar/brick unit combinations all around the world. Also, this study fulfills those requirements. Especially, masonry laid with the mud mortar meets all. Fly Ash, Ground Granulated Blast furnace Slag, and Quarry Dust have utilized the new composites' preparation with 8Molority, 10Molority developed excellent strength. The composite specimens are having compression and bond strength, ranging from 4.84-5.14 and 0.12-0.18N/mm2. The mixed ratio of materials has taken (0.5 parts of Fly Ash, 0.5 parts of Steel Slag, 1.75 parts of Soil, and 0.25 parts of Quarry Dust). The samples tested resistance against acidic, sulfate, and alkalinity indicated PH values less than 7 and 9 simultaneously. Compression strength varied from 10-20% and gained more and fit composite used for mortar in masonry works.

The sound field properties for non-cavitating marine propellers are studied using FW-H (Ffowcs William-Hawkings) acoustic analogy and BEM (Boundary Element Method) approach. For the first time, the FW-H formula to calculate acoustic pressure generated by the propeller wake sheet is proposed. The corresponding sound signal can be dominant up to several kilometres. Secondly, non-physical fictitious volume flux is observed when the permeable FW-H approach is used together with BEM. The reason is explained and a virtual source correction method is proposed to solve this problem. Furthermore, analytical analyse show that the second thickness term and the first two loading terms in Farassat 1A formula are important, and the others are negligible. The numerical studies show that the permeable FW-H approach produces underestimation when compared to the direct FW-H method, and the underestimation is severer for larger permeable surface and higher frequency. It is also found that the first loading term in Farassat 1A formula is the dominant source term in the direct FW-H method, while the first thickness term is dominant when the permeable FW-H approach is used.

The triangulation process represents a violation of the boundary between parental and child relational subsystems which, in turn, affects family dynamics and relationships. The paper, with distinct reference to marital conflict and divorced couples, describes the main causes of the triangulation process and its impact on children (and adolescents) as significant third participants within the parental conflict. Besides, it fo-cuses on long-term consequences associated with triangulation process to parental conflict exposure, that can adversely affect the well-being of children during their life-cycle, and even into adulthood. A data-search was carried out for articles to be included in the review and articles were retrieved from different electronic databases (first: Scopus and Web of Science, then: PsychINFO, Google Scholar, EBSCO and ScienceDirect,). After having initially considered 152 articles, 58 studies were selected for this research. A qualitative analysis was conducted on selected studies, focusing on: (1) different types of triangulation commonly used in intergenerational family relationships; (2) an updated summary of the research around the impact of triangulation on the well-being of children and the parent-child conflict; and (3) the main characteristics of successful intervention of preventative and psychotherapeutic treatments. In conclusion, the results, examining the long-term effects of the triangulation process, highlight the developmental paths of children that are more exposed and at risk, and focuses on the importance of preventing the intergenerational transmission of marital conflict, as a way to reduce mental health costs and to improve the well-being of children and families who are all involved in these conflicting and destructive dynamics.

Most Acinetobacter baumannii strains are naturally competent. Although some information is available about factors that enhance or reduce the frequency of transformation of this bacterium, the regulatory elements and mechanisms are barely understood. In this article, we describe studies on the role of H-NS in the regulation of expression of genes related to natural competency and the ability to uptake foreign DNA. The expression levels of the natural transformation-related genes pilA, pilT, pilQ, comEA, comEC, comF, and drpA were significantly increased in a Δhns derivative of Acinetobacter baumannii A118. Complementation of the mutant with a recombinant plasmid harboring hns restored expression levels of six of these genes (pilT remained expressed at high levels) to those of the wild-type strain. The transformation frequency of the A. baumannii A118 Δhns strain was significantly higher than that of the wild-type. Similar, albeit not identical, effects occurred when hns was deleted from the hypervirulent A. baumannii AB5075 strain. Reduction of gene expression in a few cases was not as pronounced as to reach wild-type levels, and expression of comEA was enhanced further. In conclusion, the expression of all seven transformation-related genes was enhanced after deleting hns in A. baumannii A118 and AB5075, and these modifications are accompanied by an increase in the cells’ transformability. The results demonstrate a role of H-NS in A. baumannii’s natural competence.

In this paper, we consider the relation of more than four harmonic points in a line. For this purpose, starting from the dependence of the harmonic points, Desargues’ theorems, and perspectivity, we note that it is necessary to conduct a generalization of the Desargues’ theorems for projective complete n-points, which are used to implement the definition of the generalization of harmonic points. We present new findings regarding the uniquely determined and constructed sets of H-points and their structure. The well-known fourth harmonic points represent the special case (n=4) of the sets of H-points of rank 2, which is indicated by P42.

Animal-assisted interventions (AAI) are a unique class of complementary medical treatments that can improve a patient’s quality of life, both physically and psychologically. Part I of this two-paper systematic literature review series focused on the study methods and quantitative results of researchers in this field. We continue this in-depth review here in Part II by discussing the common theories associated with AAI in the context of cancer. Of all the factors at work in human-animal interactions, researchers explicitly cite compatible animal personality, physical touch, physical movement, distraction/entertainment, and increased human interaction as the mechanisms responsible for the positive clinical outcomes observed in AAI. In various combinations, these mechanisms group under broader theoretical frameworks that attempt to fully explain the AAI context as it relates to cancer care. The social support hypothesis and the conception of a human-animal bond are the most referenced overarching frameworks. The cognitive activation theory of stress, the science of unitary human beings, and the self-object hypothesis are also referenced. We briefly consider other relevant theories commonly noted in the human-animal interactions literature that have the potential to clarify aspects of cancer-related AAI. We also discuss the neurobiological transduction mechanisms needed to connect theoretical frameworks and their mechanisms directly to the observed clinical outcomes. To advance the field, researchers should consider overarching theories with testable hypotheses when designing studies, and use consistent terminology when reporting results. This review lays a foundation for progress towards a unified theoretical framework and for effective treatment of the whole cancer patient.

In this paper, we investigate a new $q$-analogue of the higher order degenerate Changhee polynomials and numbers, which are called the Witt-type formula for the $q$-analogue of degenerate Changhee polynomials of order $r$. We can derive some new interesting identities related to the degenerate $(h,q)$-Changhee polynomials and numbers.

Helicobacter pylori is the most common human gastric infection. H. pylori stool antigen lateral flow immunochromatography assay (HpSA-LFIA) is considered one of the most cost-effective and rapid non-invasive assays (active tests). The evaluation of this test is crucial for accuracy and utility assurance. This study aimed to evaluate the polyclonal antibody-based HpSA-LFIA in comparison to a monoclonal antibody-based ELISA kit. Methodology: Stool samples were collected from 200 gastric patients for HpSA-LFIA and semi-quantitative HpSA-ELISA. Statistical analysis of the diagnostic values was performed using MedCalc software. Chi-square tests were used to determine the effects of gender and age. Results: The obtained results found that HpSA-LFIA achieved promising sensitivity (93.75%) and NPV (98.00%). However, it had poor specificity, PPV, and accuracy, respectively, 59.76%, 31.25%, and 65.31%. LR+ & LR- were 2.33% & 0.1%, respectively. Gender had no significance on the di-agnostic parameters of HpSA-LFIA. Age groups had irrelevant sensitivity; however, specificity was significantly higher in patients over 45 years. Conclusion: It was concluded that HpSA-LFIA was not accurate enough to be the sole test for di-agnosis and needs other confirmatory tests in case of positive conditions

Specifically this work is based on the concept of ‘dark energy’ as a phenomenal effect of expansion through which a theoretical value of Hubble’s constant has been introduced. It is a constant that is based on a postulate that the square root of ratio of the Siva’s constant ‘K’ and Hubble’s constant ‘H’ is exactly equal to the diameter of the neutral hydrogen atom. That is the, exact theoretical value of Hubble’s constant. This is always constant .However, space-time conversions and the changes in the velocity of light will affect the distance and velocity in Hubble’s equation. Deviation factors in velocity, distance and the Hubble’s constant have been calculated separately which are affected by change of velocity of light with expansion of space time. The observations are related to red shift. So the change factor in terms of Hubble’s constant has been calculated with respect to red shift. Thus a factor which affects the theoretical Hubble’s constant has been calculated to find the exact value of Hubble’s constant that satisfies the experimental results. The present theoretical value of Hubble’s constant has been calculated. The experimental results by plank, ACT (Atacama Cosmology Telescope), WMAP (Wilkinson Microwave Anisotropy Probe) etc. experiments are at par with the theoretical result. Thus the ontology of space time introduced in this theoretical work supposed to be correct and leads to a new theory of origin of universe for which a brief description has been provided.

In this paper, a horizontally moving suspended mass pendulum base is designed and controlled using robust control theory. H infinity optimal loop shaping with first and second order desired loop shaping function controllers are used to improve the performance of the system using Matlab/Simulink Toolbox. Comparison of the H infinity optimal loop shaping with first and second order desired loop shaping function controllers for the proposed system have been done to track the desired angular position of the pendulum using step and sine wave input signals and a promising result has been obtained succesfully.

We investigated the effect of helium atmospheric-pressure plasma (PL) and deep-ultraviolet (UV) light treatments on the adhesive properties of fiber-reinforced poly(ether-ether-ketone)polymer (PEEK). PEEK disks reinforced with carbon (CPEEK) or glass (GPEEK) fibers were polished, modified with PL and UV for 60 s, and the surface energy was calculated by measuring the contact angles. The disk surfaces were analyzed by X-ray photoemission spectroscopy. Shear bond strength testing was performed using a universal testing machine, and the fracture surfaces were observed by electron probe microanalyzer. Data were analyzed with one and two-way ANOVA and Tukey’s post-hoc test (p < 0.05). The surface energies were increased by the modifications, which created OH functional groups on the surfaces. The bond strengths of CPEEK were increased by PL and those of GPEEK were increased by PL and UV, owing to chemical bonding at the interface.

The past few years have brought substantial progress toward understanding how human cytomegalovirus (HCMV) enters the remarkably wide spectrum of cell types and tissues that the virus is observed to infect. Neuropilin-2 and platelet-derived growth factor receptor alpha (PDGFRα) were identified as receptors, respectively, for the trimeric and pentameric glycoprotein H / glycoprotein L (gH/gL) complexes that in large part govern HCMV cell tropism, while CD90 and CD147 were also found to play roles during entry. X-ray crystal structures for the proximal viral fusogen, glycoprotein B (gB), and for the pentameric gH/gL complex (pentamer) were solved. A novel virion gH complex consisting of gH bound to UL116 instead of gL was described, and findings supporting the existence of a stable complex between gH/gL and gB were reported. Additional work indicates that the pentamer promotes a mode of cell-associated spread that resists antibody neutralization, as opposed to the trimeric gH/gL complex (trimer), which appears to be broadly required for the infectivity of cell-free virions. Finally, viral factors such as UL148 and US16 were identified that can influence the incorporation of the alternative gH/gL complexes into virions. We will review these advances and their implications for understanding HCMV entry and cell tropism.

This article will briefly review the progress of h-BN based solid-state metal semiconductor metal (MSM) neutron detectors. In the last decade, several groups have been working on hexagonal boron nitride (h-BN) based solid-state neutron detectors. Recently, the detection efficiency of 59% has been reported. Efficient, low-cost neutron detectors made from readily available materials are essential for various applications. Neutron detectors are widely used to detect fissile materials and nuclear power plants for security applications. The most common and widely used neutron detectors are 3He based, which are sometimes bulky, difficult to transport, have high absorption length, need relatively high bias voltage (>1000 V), and have low Q-value (0.764 MeV). Also, 3He is not readily available material. Thus, there is a strong need to find an alternative detection material. 10B isotope has a high neutron absorption cross-section, and it has been tested as a coating on the semiconducting materials. Due to the two-step process, neutron capture through 10B, and then electron-hole pair generation in a typical semiconducting material, the efficiency of these devices is not up to the mark. The progress in h-BN based detectors requires a review to envision the further improvement in this technology.

Background: Fullerenes and metallofullerenes can be considered promising nanopharmaceuticals themselves and as a basis for chemical modification. As reactive oxygen species homeostasis plays a vital role in cells, the study of their effect on genes involved in oxidative stress and anti-inflammatory response is of particular importance. Methods: Human fetal lung fibroblasts were incubated with aqueous dispersions of C60, C70, and Gd@C82 in concentrations of 5 nM and 1.5 µM for 1, 3, 24, and 72 hours. Cell viability, intracellular ROS, NOX4, NFκB, PRAR-γ, NRF2, heme oxygenase 1, and NAD(P)H quinone dehydrogenase 1 expression have been studied. Results &amp; conclusion: The aqueous dispersions of C60, C70, and Gd@C82 fullerenes are active participants in ROS homeostasis. Low and high concentrations of AFDs have similar effects. C70 was the most inert substance, C60 was the most active substance. All AFDs have both a “prooxidant” and “antioxidant” effect, but with a different balance. Gd@C82 was a substance with more pronounced antioxidant and anti-inflammatory properties, while C70 had more pronounced “prooxidant” properties.

In this study, we define new classes of convexity called of h-Godunova-Levin and h-Godunova-Levin preinvexity, through which some new inequalities of Hermite-Hadamard type were established. These new classes are the generalisation of several known convexity including the s-convex, P-function, Godunova-Levin. Further, the properties of h-Godunova-Levin function were also discussed. Meanwhile, the applications of h-Godunova-Levin Preinvex function are given

Chlorotoxin (CTX) is a 36–amino acid peptide with 8 Cys residues that forms four Cys-Cys bonds. It has high affinity for the glioma-specific chloride channel and matrix metalloprotease-2. Structural and binding properties of CTX analogs with various Cys residue substitutions with L-a-aminobutyric acid (Abu) have been previously reported. Using 4.2 ìs molecular dynamics, we compared the conformational and essential space sampling of CTX and analogs [Abu/Ser^2,19]CTX, [Abu/Ser^5,28]CTX, [Abu/Ser^16,33]CTX, [Abu/Ser^20,35]CTX, and [Abu/Ser^{2,5,16,19,20,28,33,35}]CTX. The native and substituted peptides maintained a high degree of a-helix propensity from residues 8 through 21, with the exception of [Ser^5,28]CTX and [Abu^16,33]CTX. In agreement with previous circular dichroism spectropolarimetry results, the C-terminal b-sheet content varied less from residues 25 through 29 and 32 through 36 and was well conserved in all analogs, except: [Abu^16,33]CTX, [Ser^20,35]CTX, [Abu^{2,5,16,19,20,28,33,35}]CTX, and [Ser^{2,5,16,19,20,28,33,35}]CTX. The Cys¹⁶-Cys³³ and Cys²⁰-Cys³⁵ Cys-Cys bonds appear to be required to maintain the ab-motif of CTX. Their selective substitution with Ser^16,33 however, may mitigate the destabilizing effect of Cys¹⁶-Cys³³ substitution by the formation of an inter residue H-bond from OgH of Ser¹⁶ to OgH of Ser³³ bridged by a water molecule. All peptides shared considerable sampled conformational space, which explains the retained receptor binding of the nonnative analogs.

Many academics are critical of the current publishing system, but it is difficult to create a better alternative. This review relates to the Sciences and Social Sciences, and discusses the primary purpose of academic journals as providing a seal of approval for perceived quality, impact, significance, and importance. The key issues considered include the role of anonymous refereeing, continuous rather than discrete frequency of publications, avoidance of time wasting, and seeking adventure. Here we give recommendations about the organization of journal articles, the roles of associate editors and referees, measuring the time frame for refereeing submitted articles in days and weeks rather than months and years, encouraging open access internet publishing, emphasizing the continuity of publishing online, academic publishing as a continuous dynamic process, and how to improve research after publication. Citations and functions thereof, such as the journal impact factor and h-index, are the benchmark for evaluating the importance and impact of academic journals and published articles. Even in the very top journals, a high proportion of published articles are never cited, not even by the authors themselves. Top journal publications do not guarantee that published articles will make significant contributions, or that they will ever be highly cited. The COVID-19 world should encourage academics worldwide not only to rethink academic teaching, but also to re-evaluate key issues associated with academic journal publishing in the future.

β-cyclodextrin-based star polymers have attracted much interest because of their unique structures and potential biomedical and biological applications. Herein, we synthesized well-defined folic acid (FA)-conjugated and disulfide bond-linked star polymer ((FA-Dex-SS)-βCD-(PCL)14) acted as theranostic nanoparticles for tumor-targeted magnetic resonance imaging (MRI) and chemotherapy. Theranostic nanoparticles were obtained by loading doxorubicin (DOX) and superparamagnetic iron oxide particles (SPIO) were loaded into the star polymer nanoparticles to obtain ((FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO) theranostic nanoparticles. In vitro drug release studies showed that approximately 100% of the DOX was released from disulfide bond-linked theranostic nanoparticles within 24 h under a reducing environment in the presence of 10.0 mM GSH. DOX and SPIO could be delivered into HepG2 cells efficiently, owing to folate receptor-mediated endocytosis process of the nanoparticles and GSH triggered disulfide-bonds cleaving.Moreover, (FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO showed strong MRI contrast enhancement properties. In conclusion, folate-decorated reduction-sensitive star polymeric nanoparticles are a potential theranostic nanoparticle candidate for tumor-targeted MRI and chemotherapy.

A facile solid-phase synthetic method for incorporating the imidazoline ring motif, a surrogate for a trans peptide bond, into bioactive peptides is reported. The example described is the synthesis of an imidazoline peptidomimetic analog of an insect pyrokinin neuropeptide via a cyclization reaction of an iminium salt generated from the preceding amino acid and 2,4-diaminopropanoic acid (Dap).

The hybrid bond graph has been studied in depth for scalar bond graphs, but how does this translate to the multi-bond graph? Here, the controlled junction – used to model structural switching such as contact – is extended to the multi-bond case. This is a simple process, assuming that all bonds switch simultaneously (which makes physical sense). A controlled 0-junction is applied to multi-bond graph of a car, which can lose contact with the ground in cornering. Dynamic causality features, but this can be accommodated using an equational submodel in 20-Sim (in a manner similar to that used with scalar bond graphs). The junction is proposed for subsequent work to develop a validated multi-body dynamics car model in cornering.

In this paper, we study a generalised CIR process with externally-exciting and self-exciting jumps, and focus on the distributional properties and applications of this process and its aggregated process. The first and second moments of this jump-diffusion process are used to calculate the insurance premium based on mean-variance principle. The Laplace transform of the aggregated process is derived, and this leads to an application for pricing default-free bonds which could capture the impacts of both exogenous and endogenous shocks. Illustrative numerical examples and comparisons with other models are also provided.

Flaviviruses replicate in membrane factories associated with the endoplasmic reticulum (ER). Significant levels of flavivirus viral protein accumulation contribute to ER stress. As a consequence, the host cell exhibits an Unfolded Protein Response (UPR), subsequently stimulating appropriate cellular responses such as adaptation, autophagy or apoptosis. The correct redox conditions of this compartment are essential to form native disulfide bonds in proteins. ZIKA virus (ZIKV) has ability to induce persistent ER stress leading to activation of UPR pathways. In this study, we wondered whether ZIKV affects the redox balance and consequently the oxidative protein folding in the ER. We found that ZIKV replication influences redox state leading to aggregation of viral envelope protein as amyloid-like structures in the infected cells.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Current therapeutic protocols for the treatment of HIV infection consist of the combination of diverse anti-retroviral drugs in order to reduce the selection of resistant mutants and to allow for the use of lower doses of each single agent to reduce toxicity. However, avoiding drugs interactions and patient compliance are issues not fully accomplished so far. In this respect the identification of single agents with multitarget potential might represent the ideal solution. Accordingly, a small library of biphenylhydrazo 4-arylthiazoles derivatives has been synthesised and evaluated to investigate the ability of the new derivatives to simultaneously inhibit both associated functions of HIV reverse transcriptase. All compounds were active towards the two functions, although at different concentrations. The substitution pattern on the biphenyl moiety appears relevant to determine the activity.

An extension of the models used to generate fractal traffic flows is presented by means of the formulation of a model that considers the use of one-dimensional chaotic maps. Based on the disaggregation of the temporal series generated by the model, a valid explanation of behavior of the values of Hurst exponent is proposed and the feasibility of their control from the parameters of the proposed model is shown.

In this study, we report a detailed experimental and theoretical investigation of three glycols, namely ethane-1,2-diol, 2-methoxyethan-1-ol and 1,2-dimethoxy ethane. For the first time, the X-Ray spectra of the latter two liquids was measured at room temperature, and they were compared with the newly measured spectrum of ethane-1,2-diol. The experimental diffraction patterns were interpreted very satisfactorily with molecular dynamics calculations, and suggest that in liquid ethane-1,2-diol most molecules are found in gauche conformation, with intramolecular hydrogen bond between the two hydroxyl groups. Intramolecular H-bonds are established in the mono-alkylated diol, but the interaction is weaker. The EDXD study also evidences strong intermolecular hydrogen-bond interactions, with short O···O correlations in both systems, while longer methyl-methyl interactions are found in 1,2-dimethoxy ethane. X-Ray studies are complemented by micro Raman investigations at room temperature and at 80°C, that confirm the conformational analysis predicted by X-Ray experiments and simulations.

In this paper, the design and performance investigation of the permanent magnet machines have been done to increase the mechanical and electrical outputs improvement of the systems. A permanent magnet Dc motor (PMDM) and generator (PMDG) have been modelled and designed to improve the angular position and generated current respectively. In this work, augmentation based H 2 optimal and H infinity synthesis controllers have been designed as a controller for the two systems and a comparison between the proposed controller for tracking a reference inputs and a promising results have been obtained.

Aim: To compare the effectiveness of conventional and rotary NiTi files for Gutta-Percha (GP) removal in straight roots during retreatment root canal treatment (RCT), using manual Hedstrom files and ProTaper Universal System, respectively. Methods: It was an in-vitro experimental study using non-probability consecutive sampling. Sixty extracted single rooted maxillary and mandibular permanent teeth with straight canals were selected for this study. Following preparation, the root canals were filled with GP along with a sealer and kept for two weeks in a moist environment at room temperature. Thirty teeth were randomly allocated to the study and control groups each. GP removal was accomplished with Hedstrom files and Pro Taper retreatment files in group 1 and group 2, respectively. Digital radiographs were obtained using Kodak RVG digital radiography system software version VER.6.10.8.3-A and analyzed for the difference of opacities indicating residual GP. AutoCAD 2006 software was used to outline the root canal and the residual root filling. Independent sample t test was used to compare the total residual GP in both groups. Results: No significant difference in the residual root filling was observed following removal with conventional Hedstrom files versus ProTaper universal retreatment files. In both groups, the residual GP was confined to the apical third of the roots. Conclusion: ProTaper Universal Retreatment files and manual Hedstrom files are equally effective in the removal of GP in straight canals.

Using the h-index to assess individual researchers is not only unethical and unfair but also inaccurate and misleading. This index fails to offer a reliable measure of a researcher's impact based on their citation scores. Beyond statistical and conceptual considerations, authorship practices, especially in the case of multi-authored publications, give rise to significant problems that often go unnoticed. While some modifications of the h-index have been proposed to mitigate these weaknesses, the fundamental deficiencies persist. Most of these flaws have been effectively addressed by the c-score, a composite citation index. The c-score excludes self-citations, normalizes the number of citations by considering the number of authors in each paper, and takes into account first, single, and last authorship. This approach provides a more realistic measure of the impact of each individual researcher based on raw citations.

Protein oligomerzation is key to countless physiological processes, but also to abnormal amyloid conformations implicated in over 25 mortal human diseases. Angiogenin (h-ANG), a ribonuclease A family member, produces RNA fragments that regulate ribosome formation, the creation of new blood vessels and stress granule function. Too little h-ANG activity leads abnormal protein oligomerization resulting in Amyotrophic Lateral Sclerosis (ALS) or Parkinson’s disease. While a score of disease linked h-ANG mutants has been studied by X-ray diffraction, some elude crystallization. There is also debate regarding the structure that RNA fragments adopt after cleavage by h-ANG. Here, to better understand the beginning of the process that leads to aberrant protein oligomerization, the solution secondary structure and residue-level dynamics of WT h-ANG and two mutants: H13A and R121C, are characterized by multidimensional heteronuclear NMR spectroscopy under near physiological conditions. All three variants are found to adopt well folded and highly rigid structures in solution, although the elements of secondary structure are somewhat shorter than those observed in cystallography studies. R121C alters the environment of nearby residues only. By constrast, the mutation H13A affects local residues as well as nearby active site residues residues K41 and H119. The conformation characterization by CD and 1D 1H NMR spectroscopies of tRNAAla before and after h-ANG cleavage reveals a retention of most duplex structure and little or no G-quadruplex formation.

Helicobacter pylori is a common human pathogen that causes gastroduodenal diseases. H. pylori genome consists of numerous restriction-modification (R-M) genes. It is established that N6-adenine methylation plays a crucial role in bacterial gene regulation and virulence, but not much is known about the role of C5-cytosine methylation. In this study, we examined the influence of an orphan cytosine methyltransferase, hpyAVIBM on gastric infection in mice and cultured cells. Histopathological staining showed that the deletion of hpyAVIBM in H. pylori strain SS1 had increased damaging hemorrhagic effects on the mice stomach. The gelatin-zymography result demonstrated that the mice infected with mutant SS1ΔhpyAVIBM had significantly up-regulated pro-MMP-9 than those infected with SS1. Additionally, ELISA results of pro-inflammatory cytokines proved that mutant strain caused significantly more inflammatory effect on mice stomach than its wild-type counterpart. The immunohistochemistry data showed that mutant strain caused attenuated epithelial cell damage. Co-culture studies of H. pylori with AGS (Human Gastric Adenocarcinoma cell line) cells revealed that SS1ΔhpyAVIBM instigated significantly more apoptotic death in the AGS cells compared to the wild-type strain. Our results indicated that DNA methylation by hpyAVIBM plays a crucial role in modulating virulence factors in bacterial cells and their interaction with the host cells.

Fractal behavior and long-range dependence are widely observed in measurements and characterization of traffic flow in high-speed computer networks of different technologies and coverage levels. This paper presents the results obtained when applying fractal analysis techniques on a time series obtained from traffic captures coming from an application server connected to the Internet through a high-speed link. The results obtained show that traffic flow in the dedicated high-speed network link have fractal behavior when the Hurst exponent is in the range of 0.5, 1, the fractal dimension between 1, 1.5, and the correlation coefficient between –0.5, 0. Based on these results, it is ideal to characterize both the singularities of the traffic and its impulsiveness during a fractal analysis of temporal scales. Finally, based on the results of the time series analyses, the fact that the traffic flows of current computer networks exhibit fractal behavior with a long-range dependency is reaffirmed.

In the present paper we introduce three new classes of bi-univalent functions connected with Gregory coefficients. For functions in each of these three bi-univalent function classes we have derived the estimates of the Taylor--Maclaurin coefficients $\left|a_{2}\right|$ and $\left|a_{3}\right|$ and Fekete-Szeg\H{o} functional problems for functions belonging to these new subclasses. We defined three subclasses of the class of the bi-univalent functions $\Sigma$, namely $\mathfrak{HG}_{\Sigma}$, $\mathfrak{GM}_{\Sigma}(\mu)$ and $\mathfrak{G}_{\Sigma}(\lambda)$ by using the subordinations with the function whose coefficients are Gregory's numbers. First, we proved that these classes are not empty, i.e. contains other functions than the identity one. Using the well-known Carath\'eodory Lemma for the functions with real positive parts in the open unit disk, together with an estimation due to P. Zaprawa (see https://doi.org/10.1155/2014/357480) and another one of Libera and Zlotkiewicz, we gave upper bounds for the above mentioned initial coefficients and for the Fekete-Szeg\H{o} functionals. The main results are followed by some particular cases, and the novelty of the definitions and the proofs could involve further studies for such type of similarly defined subclasses.

Three ternary mixtures composed by choline chloride (ChCl), ethylene glycol (EG) and a second hydrogen bond donor (HBD) as ethanol (A), 2-propanol (B), and glycerol (C) were studied in terms of composition related to the band gap energy (BGE). A Design of Experiments (DoE) approach, and in particular a Simple Lattice three-components design, was employed for determining the variation of the BGE upon the composition of each system. UV-VIS analysis and subsequent Tauc plot methodology provided the data requested from the DoE and multivariate statistical analysis revealed a drop of the BGE in correspondence to specific binary compositions for systems A and B. In particular, a BGE of 3.85 eV was registered for the mixtures ChCl/EtOH (1:1), and ChCl/2-propanol (1:1), which represents one of the lowest values ever observed for these systems.

The closed forms of the non-resonant thermonuclear function in the Maxwell-Boltzmann and Tsallis case with depleted tail are obtained in generalized special functions. The results are written in terms of H-function of two variables. The importance of the results in this paper lies in the fact that the reaction rate probability integrals in Maxwell-Boltzmann and Tsallis cases are not obtained by the conventional method of approximation or by means of a single variable transform technique but by means of a two variable transform method. The Behaviour of the depleted non-resonant thermonuclear functions are examined using graphs. The results in the paper are of much interest to astrophysicists and statisticians in their further work in this area.

A methodology based on the concepts that arise from Density Functional Theory named Conceptual Density Functional Theory (CDFT) was chosen for the calculation of some global and local reactivity descriptors of the Discodermins A-H family of marine peptides through the consideration of the KID (Koopmans in DFT) technique that was successfully used in previous studies of this kind of molecular systems. The determination of active sites of the studied molecules for different kind of reactivities was achieved by resorting to some CDFT-based descriptors like the Fukui functions as well as the Parr functions derived from Molecular Electron Density Theory (MEDT). A few properties identified with their ability to behave as a drug and the bioactivity of the peptides considered in this examination were acquired by depending on a homology model by studying the correlation with the known bioactivity of related molecules in their interaction with various biological receptors. With the further object of analyzing their bioactivity some parameters of usefulness for future QSAR studies, their predicted biological targets and the the ADME (Absorption, Distribution, Metabolism, and Excretion) parameters related to the Discodermins A-H pharmacokinetics are also reported.