Modeling and Simulation of Vehicle Windshield Wiper System using H Loop Shaping and Robust Pole Placement Controllers

Vehicle windshield wiper system increases the driving safety by contributing a clear shot viewing to the driver. In this paper, modelling, designing and simulation of a vehicle windshield wiper system with robust control theory is done successfully. H  loop shaping and robust pole placement controllers are used to improve the wiping speed by tracking a reference speed signals. The reference speed signals used in this paper are step and sine wave signals. Comparison of the H  loop shaping and robust pole placement controllers based on the two reference signals is done and convincing results have been obtained. Finally the comparative results prove the effectiveness of the proposed H  Loop Shaping controller to improve the wiping mechanism for the given two reference signals. [Mustefa Jibril, Messay Tadese, Eliyas Alemayehu Tadese. Modelling and Simulation of Vehicle Windshield Wiper System using H  Loop Shaping and Robust Pole Placement Controllers. Rep Opinion 2020;12(9):1418]. ISSN 1553-9873 (print); ISSN 2375-7205 (online). http://www.sciencepub.net/report. 4. doi:10.7537/marsroj120920.04.


1.
Introduction Driving a vehicle is complicated in harsh weather condition without using glass wiper system. Controlling the wiper speed based on the change in weather condition is one of the research area in automotive industries now a day. Recently, the wiper speed is adjusted manually controlled by the driver. Dc motors are used to drive the wiper system based on feed forward techniques. In this paper a separately excited Dc motor is designed and controlled using robust control method to improve the feed forward wiper system performance.

2.
Mathematical Modelling Consider the electromechanical car mirror wiper system shown in Figure 1.

Figure 1 Electromechanical car mirror wiper system
The motor shown is a servomotor, a dc motor designed in particular for use in a control system. The operation of this device is as follows: A fixed voltage is carried out to the field winding. A voltage is implemented as an input to the servo motor and the angular position c of the wiper arm is the output of the device. The input voltage is implemented to the armature circuit of the dc motor. A constant voltage is carried out to the field winding. If an errors exists, the motor develops a torque to rotate the output load in the sort of way as to reduce the error to zero. For constant field current, the torque evolved by using the motor is is the motor torque constant and ia is the armature current.
When the armature is rotating, a voltage proportional to the fabricated from the flux and angular velocity is brought on within the armature. For a constant flux, the brought about voltage eb is without delay proportional to the angular velocity Where eb is the back emf, K2 is the back emf constant of the motor, and  is the angular displacement of the motor shaft. The speed of an armature-managed dc servomotor is managed via the armature voltage e (t). The differential equation for the armature circuit is Taking the Laplace transform the equation will be Where J0 is the inertia of the combination of the motor, load, and gear train referred to the motor shaft and b0 is the viscous-friction coefficient of the aggregate of the motor, load, and gear train mentioned the motor shaft.
By eliminating   a I s from Equations (5) and (7), we obtain We assume that the gear ratio of the gear train is such that the output shaft rotates n times for each revolution of the motor shaft. Thus, The wiper arm speed can be evaluated by using an integrator to the wiper arm position as Substituting Equation (10) in to Equations (9) and to Equations (8) gives us the transfer function between the applied voltage and the wiper speed as The parameters of the system is shown in Table 1 below.

Proposed Controllers Design 3.1 H infinity Loop shaping using Glover-McFarlane method Controller Design
The block diagram of the car mirror wiper system with H infinity Loop shaping design using Glover-McFarlane method is shown in Figure 2  A feedback controller, KS, is synthesized that robustly stabilizes the normalized left cop rime factorization of G, with a balance margin. It may be proven that the frequency response of KsW2GW1 will be much like that of W2GW1. On the other hand, if the viable gain is simply too large, this will probable indicate an overdesigned case in appreciate of the robustness, which means that the performance of the system can also in all likelihood be progressed by the usage of a larger in computing Ks. The final feedback controller, K final, is then constructed with the aid of combining the H infinity controller Ks, with the weighting functions W1 and W2 such that   The block diagram of the car mirror wiper system with robust pole placement method is shown in Figure 3. The state equations for the closed-loop system of Figure 3 can be written by inspection as The poles for this system is chosen as Solving using Matlab the robust pole placement algorithm gain will be   46 26727 790 125 K    

Result and Discussion
In this section, the Simulink model design and simulation of the vehicle windshield wiper system using H infinity loop shaping and robust pole placement controllers by comparing the two proposed controllers for tracking the step and sine wave speed references.

Comparison of the proposed controllers for tracking the step speed reference
The Simulink model of the vehicle windshield wiper system using H infinity loop shaping and robust pole placement controllers for tracking the step speed reference is shown in Figure 4 below. Figure 4 Simulink model of the vehicle windshield wiper system using H infinity Loop Shaping and Robust Pole Placement Controllers for tracking the step speed reference The wiper system performance for the proposed controllers using a step reference (step change from 0 to 6 m/s) of the wiper speed simulation is shown in Figure 5 below.

Figure 5 Simulation result for a step reference input
The data of the rise time, percentage overshoot, settling time and peak value is shown in Table 1.

Comparison of the proposed controllers for tracking the Sine Wave speed reference
The Simulink model of the vehicle windshield wiper system using H infinity loop shaping and robust pole placement controllers for tracking the sine wave speed reference is shown in Figure 6 below. Figure 6 Simulink model of the vehicle windshield wiper system using H infinity loop shaping and robust pole placement controllers for tracking the sine speed reference The wiper system performance for the proposed controllers using a sine wave reference (wiper moving in the forward and reverse with 6 m/s) of the wiper speed simulation is shown in Figure 7 below.

Figure 7 Simulation result for a sine wave reference input
The simulation result shows that the vehicle windshield wiper system with H infinity loop shaping controller track the reference speed better than the vehicle windshield wiper system with robust pole placement controller.

Conclusion
The vehicle windshield wiper system is designed and simulated based on the given control signals using Matlab/Simulink and a promising result have been analyzed. The performance of the vehicle windshield wiper system is tested for wiping speed regulation using track a signal method. Comparison of the vehicle windshield wiper system with H infinity loop shaping and robust pole placement controllers is done for a step and sine wave reference speed signals and the vehicle windshield wiper system with H infinity loop shaping controller shows a good result in improving the wiping mechanism in almost the all performance measures taken. Finally the comparative results prove the effectiveness of the proposed H  Loop Shaping controller to improve the wiping mechanism for the given two reference signals.