: AliCPT-1 is the first Cosmic Microwave Background (CMB) experiment in China, dedicated to achieve accurate measurements of B-mode polarization. Situated in Ali of Tibet, China, this telescope is currently undergoing deployment and will operate in two frequency bands centered at 90 and 150 GHz. The Far-Field Flat Mirror（FFF）is a calibration device of AliCPT-1 telescope for far-field beam mapping. The design of FFF is optimized for easy assembly and adjustment. Meteorological station data reveals that the maximum wind speed near FFF is 17.5 m/s, while the maximum wind speed on the windward side is 8 m/s. The wind pressure on FFF was analysed using a maximum wind speed of 17.5m/s as the input condition, based on the fluid-structure coupling method in ANSYS. The results demonstrate that it is safe and reliable when withstanding combined gravity and wind pressure loads. The torque on the mount is within the motor rated torque. The flatness of the FFF reflective surface can be adjusted to an RMS value of 0.05 mm when taken into account the effect of gravity and assembly accuracy. The deformation caused by the maximum wind loads is approximately 0.0587 mm under the protection of wind-proof wall. The combined deformation is 0.077 mm in RMS value combining the two influences, which is less than 1/20 of wavelength. The FFF mirror assembly is stable and precisely for telescope calibration.

Hydatid cyst fluid is a complex biological substance consisting primarily of water, proteins, lipids, carbohydrates, salts, enzymes, hormones, growth factors, immune modulators, and other bioactive molecules. Antigens, including antigen B (AgB) and antigen 5 family members (Ag5), have been identified in hydatid cyst fluid and have been shown to have the ability to inhibit cancer progression. The exact mechanisms by which these components exert inhibitory effects on cancer progression are not fully understood, but it is believed that they may influence multiple signaling pathways involved in cell proliferation, survival, angiogenesis, and metastasis. In vitro studies have demonstrated that treatment with hydatid cyst fluid or specific antigens can inhibit cell growth, induce apoptosis, and suppress the migration of cancer cells. Animal model studies have also demonstrated significant inhibition of tumor growth, reduction in angiogenesis, and suppression of metastasis. Limited clinical studies have shown promising outcomes, including improved overall survival and reduced recurrence rates among breast cancer patients receiving AgB immunotherapy alongside standard treatment.

Prediction of survival in very preterm infants is very important in terms of clinical medicine and parent counseling. In this prospective study involving 96 very preterm infants, we evaluated whether metabolomic analysis of gastric fluid and urine samples obtained soon after birth could predict survival on days of life (DOL) 3 and 15 as well as overall survival up to hospital discharge. Gas chromatography-mass spectrometry (GC-MS) profiling was used. Uni- and multivariate statistical analyses were carried out to evaluate significant metabolites and their prognostic value. Differences in several metabolites were identified between survivors and non-survivors at the time-points of the study. Binary logistic regression showed that certain metabolites in the gastric fluid including arabitol as well as succinic, erythronic and threonic acids was associated with DOL 15 and overall survival. Gastric glyceric acid was also associated with DOL 15 survival. Urine glyceric acid could predict survival on DOL 3 and overall survival. In conclusion, non-surviving preterm infants showed a different metabolic profile compared survivors showing a significant discrimination with the use of GC-MS-based gastric fluid and urine analysis. Results of this study support the usefulness of metabolomics in developing survival biomarkers in very preterm infants.

The evidence supports the occurrence of environmentally induced paternal epigenetic inheritance shaping the offspring phenotype in the absence of direct or indirect paternal care, and the empirical results clearly indicate that sperm epigenetics is one of the major actors mediating these paternal effects. However, sperm often make up only a small fraction of the male ejaculate in animals. Males also have a complex mixture of proteins, peptides, types of small RNAs, and cell-free DNA fragments in their seminal fluid. These molecules are in close contact with reproductive cells, tissues, organs, and other molecules of both males and females during reproduction. Moreover, their production and use are very sensitive to environmental conditions which makes them potential modulators of environmentally and developmentally induced paternal effects on the next generation(s). Although there is some intriguing evidence of seminal fluid-mediated paternal epigenetic effects, the underlying molecular mechanisms remain poorly defined. In this review, I discuss the current evidence regarding the association between seminal fluid and environmentally induced paternal effects, the possible trajectories, and the mechanisms in which seminal fluid can involve to mediate paternal epigenetic inheritance.

Atopic dermatitis (AD) is a protease-modulated chronic disorder with heterogenous clinical manifestations which may lead to an imprecise diagnosis. So far, there are no diagnostic protease tests for AD. We explored the gingival crevicular fluid (GCF) protease profile of periodontally-healthy individuals with moderate/severe AD compared to healthy controls. An exploratory case-control study was conducted. Matching AD patients (n=6) and controls (n=6) were enrolled at the International Center for Clinical Studies, Santiago, Chile. Complete dermatological and periodontal evaluations (involving the collection of GCF samples) were made. The levels of 35 proteases were analyzed using a human protease antibody array. The GCF levels of zinc-binding ADAM8, ADAM9, MMP8 and Neprilysin/CD10, aspartyl-binding Cathepsin E, and serin-binding Protein convertase9 and uPA/Urokinase proteases were lower in moderate/severe AD patients compared to controls (p<0.05). No inter-group differences in the levels of the other 28 proteases were found. MMP8, Cathepsin E and ADAM9 were the biomarkers with the highest sensitivity and specificity regarding the detection of AD (p < 0.05). The area under receiver operating characteristic (ROC) curve for MMP-8+ADAMP-9 was 0.90. In conclusion, differences in the protease profile between AD and control patients associated with MMP8, Cathepsin E and ADAM9. MMP8, ADAM9 and Cathepsin E may be useful as combined diagnostic and therapeutic biomarkers of moderate/severe AD.

Sparse recovery of fluid flows using data-driven proper orthogonal decomposition (POD) basis is systematically explored in this work. Fluid flows are manifestations of nonlinear multiscale PDE dynamical systems with inherent scale separation that impact the system dimensionality. Given that sparse reconstruction is inherently an ill-posed problem, the most successful approaches require the knowledge of the underlying basis space spanning the manifold in which the system resides. In this study, we employ an approach that learns basis from singular value decomposition (SVD) of training data to reconstruct sparsely sensed information. This results in a set of four control parameters for sparse recovery, namely, the choice of basis, system dimension required for sufficiently accurate reconstruction, sensor budget and their placement. The choice of control parameters implicitly determines the choice of algorithm as either $l_2$ minimization reconstruction or sparsity promoting $l_1$ norm minimization reconstruction. In this work, we systematically explore the implications of these control parameters on reconstruction accuracy so that practical recommendations can be identified. We observe that greedy-smart sensor placement provides the best balance of computational complexity and robust reconstruction for marginally oversampled cases which happens to be the most challenging regime in the explored parameter design space.

Over the past decade, Knowledge bases (KB) have been increasingly utilized to complete and enrich the representation of queries and documents in order to improve the document retrieval task. Although many approaches have used KB for such purpose, understanding how effectively lev-erage entity-based representation still needs to be resolved. This paper proposes a Purely Enti-ty-based Semantic Search Approach for Information Retrieval (PESS4IR) as a novel solution. The approach includes (i) its own entity linking method, (ii) an inverted indexing method, and for document retrieval and ranking, (iii) an appropriate ranking method is designed to take advantage of all the strengths of the approach. We report the findings on the performance of our approach tested by queries annotated by two known entity linking tools, REL and DBpedia-Spotlight. The experiments are performed on the standard TREC 2004 Robust and MSMARCO collections. By using the REL method, for queries whose all terms are annotated and whose average annotation scores are greater than or equal to 0.75, our approach achieves the maximum nDCG@5 score (1.000). Thus, using our approach with any other document retrieval method would be an added value, unless that method achieves the maximum nDCG@5 score for those highly annotated queries.

Nature-based Solutions (NbS) have rapidly been gaining traction across the research, policy, and practice spheres, touted as transformative actions to jointly address biodiversity loss and climate change. However, there are multiple, alternative ways to imagine NbS in those three spheres. To inform the NbS discourses across these three spheres, we critically reflect on the prevailing framing of NbS and consider the potential of a different framing of NbS to support transformations towards regenerative relationships between humans and nature. Such reflection is urgently needed to ensure that research, policy, and practice delivers on the transformative ambitions of NbS. We propose a novel “core framing” of NbS, charting two pathways for how such a framing can support a human value-based transformation – first through influencing individual beliefs and values, and second through the communication and application of the NbS concept in research, policy, and practice. We argue that for NbS to support transformation, it must support a reframing of human-nature relationships, one where the interdependencies between people and nature are recognized as essential for social and environmental well-being. We elaborate on how such a framing is key to support inclusivity and collaboration between diverse research perspectives, policy objectives across scales, and implementation practices, to deliver successful NbS.

The demographic profile of patients transitioning from chronic kidney disease to renal replacement therapy is changing, with a higher prevalence of aging patients with multiple comorbidities such as diabetes mellitus and heart failure. Cardiovascular disease remains the leading cause of mortality in this population, exacerbated by the cardiovascular stress imposed by the HD procedure. The first year after transitioning to hemodialysis is associated with increased risks of hospitalization and mortality, particularly within the first 90–120 days, with greater vulnerability observed among the elderly. This review, based on data from clinics of Fresenius Medical Care Europe, Middle East, and Africa NephroCare, aims to optimize hemodialysis procedures to reduce mortality risk in stable incident and prevalent patients. It addresses critical aspects such as treatment duration, frequency, choice of dialysis membrane, dialysate composition, blood and dialysate flow rates, electrolyte composition, temperature control, target weight management, dialysis adequacy, and additional protocols, with a focus on mitigating prevalent intradialytic complications, particularly intradialytic hypotension prevention.

Computational Fluid Dynamics (CFD) is revolutionizing the oil and gas industry by offering powerful insights and innovative solutions. This paper explores the cutting-edge applications of CFD in enhancing and innovating within the sector. CFD simulations provide engineers with invaluable insights into fluid behavior, enabling optimized designs and informed decision-making. The software facilitates foresight by predicting system performance, optimizing drilling techniques, and maximizing reservoir management strategies. Moreover, CFD optimizes equipment design, increases operational efficiency, and reduces costs through virtual testing, eliminating the need for costly physical prototypes. The application of CFD aligns with the United Nations Sustainable Development Goals (SDGs), promoting energy efficiency, climate action, responsible production, and sustainable consumption. It addresses flow assurance challenges, enhances safety protocols, and mitigates environmental impacts. CFD is a powerful tool driving innovation, resilience, and sustainability within the oil and gas industry, ensuring a more efficient, safe, and environmentally conscious future. As advancements in CFD methodologies continue, the potential for further enhancements and breakthroughs within the sector becomes even more promising, driving the industry towards a sustainable and prosperous future.

Coronavirus disease 2019 (COVID-19), caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), mainly affects the respiratory system with some patients rapidly progressing to acute respiratory distress syndrome (ARDS). The most common symptoms of the patients are fever, cough, dyspnea, myalgia, and fatigue. Nasopharyngeal and oropharyngeal swab specimens tested by real-time reverse transcription-polymerase chain reaction (RT-PCR) are the most commonly used methods to diagnose COVID-19. Herein, we investigate and discuss a young case of COVID-19, without any pre-existing medical conditions, whose both nasopharyngeal and oropharyngeal swab tests of SARS-CoV-2 were negative in the prodromal phase. However, after three days, with severe dyspnea and rapidly progressed acute respiratory distress syndrome (ARDS), the case was identified as infected by COVID-19 by testing bronchoalveolar lavage fluid (BALF). The patient was intubated in the intensive care unit (ICU) but expired on the fourth day. This case shows the importance of active and accurate monitoring of the patients showing COVID-19 symptoms. Although the BALF test has a higher exposure risk, it is considered more accurate and recommended if performed by an expert operator.

In this paper, we introduce a compressible formulation for dealing with 2D/3D compressible interfacial flows. The formulation is combined with an original monolithic solver, according to which a strong velocity-pressure coupling is achieved. The results show that the scheme can ensure accuracy and stability for various fluid flow scenarios: from the standard incompressible conditions to compressible flows, spanning both single-phase and two-phase flows.

In this work, the analytical treatment of Fourth order pd equations has been discussed with the variational iteration algorithm with an auxiliary parameter. The technique has the capability of reducing the size of computational work and easily overcomes the difficulty of the perturbation method or Adomian polynomials. Comparison with the classic variational iteration algorithm- is carried out, showing that the modification is more efficient and reliable.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p &lt;0.001) and рhosphates (phosphorus) (-23.07%, p &lt;0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p &lt;0.001) and phosphorus (-14%, p &lt;0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

In natural, laboratory and industrial conditions, the density of a fluid or gas, depending on temperature, pressure, concentration of dissolved substances or suspended particles, changes under the influence of a large number of physical factors. We assume that undisturbed liquid is stratified. The analysis is based on a system of fundamental equations for the transfer of energy, momentum and matter in periodic flows of a viscous compressible fluid. The propagation of periodic flows in viscous uniformly stratified fluids is considered. Taking into account the compatibility condition, dispersion relations are constructed for two-dimensional internal, acoustic and surface linear disturbances with a positive definite frequency and complex wave number in a compressible viscous fluid exponentially stratified by density. The temperature conductivity and diffusion effects are neglected. The obtained regularly perturbed solutions to the equations describe weakly damped waves. Singular solutions characterize the thin ligaments that accompany each type of wave. In limiting cases, the constructed solutions transform into known expressions for a viscous homogeneous and ideal fluid or degenerate.

A new process is reported for the incorporation of a fluoropolymer into a solid perovskite film. Poly(trifluoroethyl methacrylate) [CH2C(CH3)(CO2CH2CF3)]n was delivered to methylammonium lead iodide (CH3NH3PbI3) perovskite films by crystallizing the film in supercritical carbon dioxide/ethanol containing the dissolved fluoropolymer. The surface was characterized before and after fluoropolymer exposure using scanning electron microscopy, Raman spectroscopy and contact angle measurements. The results indicate that the fluoropolymer was incorporated into the perovskite film during the supercritical fluid crystallization process.

Catamaran hulls have always been associated with smaller vessels in naval engineering and construction. However, recent research results have shown that by considering specific criteria based on materiality, structure and functionality, they can be designed for a more complex industry, such as hydrofoil design. Among the challenges in this type of vessel, one of the most difficult variables is estimating the resistance to the advance in the function of the degree of uncertainty generated. This research focuses on optimising the drag of a sport sailing catamaran by implementing hydrofoils, through the application of computational fluid dynamics (CFD), at different speeds to demonstrate that it is possible to modify and improve the current appendages of this vessel.

Analyzing synovial fluid from joints affected by the pathological process of psoriatic arthritis is part of the overall patient examination, since it may have differential diagnostic significance. The purpose of this study was to assess the presence of crystals in the synovial fluid of psoriatic arthritis patients as biomarkers for disease activity. Materials and methods: The synovial fluid of 156 patients with proven PSA diagnosis (patients covered CASPAR criteria) was analyzed over 24 months and compared to 50 patients with activated gonarthrosis. The Leica DM4500P polarization microscope (Leica Microsystems, Germany) was used for crystal detection. Pain and disease activity measures were also evaluated (PSA VAS for pain, DAPSA, PASDAI, mCPDAI, and HAQ-DI). The statistical analysis was carried out using SPSS version 26 with a significance set at p < 0.05. Results: The macroscopic appearance of synovial fluid from patients with psoriatic arthritis was clear in 84.6% of the patients. Synovial fluid crystals were found in 23.71% of patients with psoriatic arthritis - predominantly monosodium urate (67.58%) but also calcium pyrophosphate (21.62%) and lipid drops (5.4%). The presence of monosodium urate crystals significantly correlates with all pain and disease activity measures – VAS for pain, DAPSA, PASDAI, mCPDAI, and HAQ-DI. In 67.56% of patients with established crystals treatment with an anti-TNF blocker was started at the discretion of the treating rheumatologist due to high levels of disease activity. Conclusion: Examining the synovial fluid in PSA patients is a necessary minimally invasive procedure in cases of joint effusion, since the presence of synovial fluid crystals is a significant indicator of disease severity. The current analyses demonstrate that the presence of synovial fluid crystals in PSA patients can be used as a biomarker for disease severity and the necessity to commence biological treatment (most often TNF-a-blocker).

The computing power of smartphones has not received considerable attention in the mainstream education system. Most of the education-oriented smartphone applications (apps) are limited to general purpose services like Massive Open Online Courses (MOOCs), language learning, and calculators (performing basic mathematical calculations). Greater potential of smartphones lies in educators and researchers developing their customized apps for learners in highly specific domains. In line with this, we present Fluid Dynamics, a highly accurate Android application for measuring flow properties in compressible flows. This app can determine properties across the stationary normal and oblique shock, moving normal shock and across Prandtl $-$ Meyer expansion fan. This app can also measure isentropic flows, Fanno flows, and Rayleigh flows. The functionality of this app is also extended to calculate properties in the atmosphere by assuming the International Standard Atmosphere (ISA) relations and also flows across the Pitot tube. Such measurements are complicated and time-consuming since the relations are implicit and hence require the use of numerical methods, which give rise to repetitive calculations. The app is an efficient semi-implicit solver for gas dynamics formulations and uses underlying numerical methods for the computations in a graphical user interface (GUI), thereby easing and quickening the learning of concerned users. The app is designed for the Android operating system, the most ubiquitous and capable surveillance platform, and its calculations are based on JAVA based code methodology. In order to check its accuracy, the app's results are validated against the existing data given in the literature.

Prediction of the likely evolution in the traffic scenes is a challenging task because of high uncertainty of sensing technology and dynamic environment. It leads to failure of planning for intelligent agents like autonomous vehicles. In this paper, we propose a fluid-based physical model to present the influence of surrounding object's motion on driving safety. In our pipeline, the input sensor could be LiDAR, camera, or multi-modal data. We use a Kalman filter to estimate the state space of each detected object, and adopt the properties of stable fluid to build a riskmap based on the density field. The noisy state space are then modeled as the boundary conditions in the simulation of advection and diffusion process. We test our approach on the public KITTI dataset and find this model could handle the short-term prediction in case of misdetection and tracking failure caused by object occlusion, which shows promising in collision risk assessment on road scenes.

The Landau damping effect was observed in collisionless plasma, as a microscopic resonant mechanism between electromagnetic radiation and the collective modes. In this paper we demonstrate the occurrence of the Landau damping at macroscopic scale in the interaction between water waves and anharmonic lattice of magnetic buoys. By coupling the Navier-Stokes equations for incompressible fluid with the nonlinear dynamics of an anharmonic magnetic lattice we obtain a resonant transfer of momentum and energy between the two systems. The velocity of the flow is obtained in the Stokes approximation with Basset type of drag force. The dynamics of the buoys is calculated in the surfactant approximation for a specific frequency, then we use Fourier analysis to obtain the general time variable interaction. After involving an integral Dirichlet transform we obtain the time dependent expression of the drag force, the interaction waves-lattice with a new term in the form of a Caputo fractional derivative. We compare the results of the model with experiments performed in a wave tank with free floating magnetic buoys under the action of small amplitude gravitational waves. This configuration can be applied in studies for the attenuation with resonant damping of rogue waves, storms or tsunamis.

Abstract: The trend of fasting until noon (omission or delayed breakfast) is increasingly prevalent in modern society. This eating pattern triggers discordance between endogenous circadian clock rhythms and the feeding/fasting cycle and is associated with an increased incidence of obesity and T2D. Although the underlying mechanism of this association is not well understood, growing evidence suggests that fasting until noon, also known as an “extended postabsorptive state,” has the potential to cause a deleterious effect on clock gene expression and disrupted regulation of body weight, postprandial and overall glycemia, skeletal muscle protein synthesis, appetite and may also lead to lower energy expenditure. This manuscript overviews the clock gene-controlled glucose metabolism during the active and resting phases. The consequences of postponing until noon the transition from postabsorptive to fed state on glucose metabolism, weight control, and energy expenditure. Finally, we will discuss the metabolic advantage of shifting more energy, carbohydrates (CH), and proteins to the early hours of the day.

Total-body PET/CT scanners provide increased sensitivity, enabling the adjustment of imaging parameters by reducing injected activity or shortening acquisition time. This study aimed to evaluate the limitations of reduced [18F]FDG activity doses on image quality, lesion detectabil-ity, and quantification of lesion uptake in the Biograph Vision Quadra, as well as to assess the benefits of the recently introduced ultra-high sensitivity mode in a clinical setting. A number of 26 patients who underwent [18F]FDG-PET/CT (3.0 MBq/kg, 5 min. scan time) were included in this analysis. PET raw data was rebinned for shorter frame durations to simulate 5 min. scans with lower activities in high sensitivity (HS) and ultra-high sensitivity (UHS) modes. Image quality, noise, and lesion detectability (n=82) were assessed using a 5-point Likert scale. The co-efficient of variation (CoV), signal-to-noise ratio (SNR), tumor-to-background ratio (TBR), and standardized uptake values (SUV) including SUVmean, SUVmax, and SUVpeak were evaluated. Sub-jective image ratings were generally superior in UHS compared to HS mode. At 0.5 MBq/kg, le-sion detectability decreased to 95% (HS) and 98% (UHS). SNR was comparable at 1.0 MBq/kg in HS (5.7±0.6) and 0.5 MBq/kg in UHS (5.5±0.5). With lower doses, there were negligible reductions in SUVmean and SUVpeak, whereas SUVmax increased steadily. Reducing [18F]FDG activity to 1.0 MBq/kg (HS/UHS) in a total-body PET/CT provides diagnostic image quality without statistical-ly significant changes in uptake parameters. UHS mode improves image quality, noise, and le-sion detectability compared to HS mode.

The study explored the correlation between serum biomarkers and hepatocellular carcinoma detection in various fishing groups, utilizing a descriptive and experimental approach in Bangladesh. The study identified fishers often consume tobacco, polluted drinking water, and lack sufficient sunlight, all of which are extremely detrimental to their health. Fishermen who mostly fish at night and spend little time on the water during the daytime hours do not get enough sunlight, nor do they get enough vitamin D. An increased risk of liver cancer was found to be directly and strongly correlated with insufficient serum levels of vitamin D. In addition, a negligent lifestyle, a lack of awareness about hepatitis, and inadequate nutritional assistance have significantly increased their risk. Our results contribute to the information on HCC assessment and evaluation by clarifying the relevance of serum vitamin D, alpha-fetoprotein (AFP), creatinine (Cr), and hemoglobin A1C (HbA1c) in distinguishing between categories and sexes. According to the study, the combination of AFP, Vitamin-D, and Cr (AFP+Vit-D+Cr) has a high predictive value, which improves diagnosis and offers a reliable instrument for identifying liver cancer.

Cerebrospinal fluid contacting neurons (CSF-cNs) are a specific type of neurons located around the ventricles in the brain and the central canal in the spinal cord and have been demonstrated to be intrinsic sensory neurons in the central nervous system (CNS). One of the important channels responsible for the sensory function is polycystic kidney disease 2-like 1 (PKD2L1) channel. Most of the studies concerning the distribution and function of the PKD2L1-expressing CSF-cNs in the spinal cord have previously been performed in non-mammalian vertebrates. In the present study immunohistochemistry was performed to determine the distribution of PKD2L1-immunoreactive (IR) CSF-cNs in the spinal cords of 4 mammalian species: mouse, rat, cat, and macaque monkey. Here, we found that PKD2L1-expressing CSF-cNs were present at all levels of the spinal cord in these animal species. Although the distribution pattern was similar across these species, differences existed. Mice and rats presented a clear PKD2L1-IR cell body labeling, whereas in cats and macaques the PKD2L1-IR cell bodies were more weakly labeled. Ectopic PKD2L1-IR neurons away from the ependymal layer were observed in all the animal species although the abundance and the detailed locations varied. The apical dendritic protrusions towards the lumen of the central canal were clearly seen in all the animal species, but the sizes of protrusion bulbs were different among the species. PKD2L1-IR cell bodies/dendrites were co-expressed with doublecortin, MAP2 (microtubule-associated protein 2) and aromatic L-amino acid decarboxylase, but not with NeuN (neuronal nuclear protein), indicating their immature property and ability to synthesis monoamine transmitters. In addition, in-situ hybridization performed in rats revealed PKD2L1 mRNA expression in the cells around the central canal. Our results indicate that the intrinsic sensory neurons are conserved across non-mammalian and mammalian vertebrates, and that this may play an essential role in the regulation of motor and sensory functions as well as in the maintenance of homeostasis in the CNS.

Backgroumd: The feeling of nasal obstruction is one of the most complaints of the Ear Nose and Throats (ENT) patients. The reason of this complaint is variable, such as Nasal Septal Deviation (NSD). NSD is a significant obstacle to normal respiration and the volume of air entering the lungs. Understanding how the deviation causes the obstruction is so important, because it leads to better management of this disease. Rhinomanometry and acoustic rhinometry are methods that are used for objective evaluation of upper airway, but they are semi invasive and the accuracy are not guaranteed. With development of Computed Tomography (CT scan) and Computational Fluid Dynamics (CFD), numerical studies on airflow in different parts of the nasal cavity have been performed. Objectives: The purpose of this study was to compare nasal airflow patterns between patient with NSD and healthy nasal cavity using a computational fluid dynamics (CFD) Methods: A patient with NSD and a healthy human were selected. Using CFD, the maximal airflow velocity, nasal resistance, maximal Wall Shear Stress (WSS), and pressure drop in bilateral nostrils of both cases were assessed. Results: Pressure and velocity profiles are evaluated at a mass flow rate of 17.4 Liters Per Minute (LPM). The velocity profile shows an abnormal flow profile in the septal deviated nasal cavity and the peak velocity is observed at the middle nasal region, whereas this point is at the nasal valve level in a healthy nasal cavity. Wall shear stress (WSS) caused by NSD is lower than in normal nasal cavities. The pressure drop in a nasal cavity with deviated septum is higher than in a healthy nasal cavity. Based on the results of this investigation nasal resistance in NSD was higher than in normal, healthy nasal cavity. Conclusions: NSD plays an important role in nasal airflow regime and it results in the feeling of obstruction comparing to normal nasal cavity. Also there is a promising future for CFD to become a useful tool in understanding airflow physiology and pathology.

Cerebrospinal fluid (CSF)-contacting neurons (CSF-N) located in the surface of both brain ventricles and the central canal (cc) in the spinal cord. The cc and CSF maintain a proliferative niche for neural progenitor cells and play a vital role in development of the brain. The CSF circulates in the ventricles and the subarachnoid spaces with the CSF rhythmic flow: cardiac pulsation and respiratory fluctuation. A new concept of CSF motion may be contrary to the classical one that the direction of CSF motion may vary in direction and may be dynamic in its location. The CSF pressure may also depend on the body position. Moderate music-making has been considered a potential approach for rehabilitative and restorative therapy of brain dysfunctions. Recently, we find that the CSF-Ns are present in both the interior CFS in the cc and also exterior CSF around the surface of the spinal cord. We hypothesize that CSF-N as mechanical sensors in the spinal cord could sense motion of the spinal cord. The myodural bridge is a ligament connecting a pair of deep, upper-neck muscles to the dura mater, which envelops the arachnoid mater and contains the CSF surrounding the brain and the spinal cord. We figure out the term “CSF-static compartment” and classify CSF storage location as rostral pool and caudal pool to demonstrate our hypothesis. We presume that the somatic body movement with music-making and rehabilitation-based interventions would orchestrate the CSF motion with head movement, myodural bridge stretching and puling as well as spinal bending.

The deep Cretaceous tight sandstone in Kuqa Depression of Tarim foreland basin is an ultra-low porosity and ultra-deep gas-bearing reservoir, which is characterized by small pores, fine throats, and poor connectivity. The wireline logging responses are so complex, and especially, it is difficult to identify fluid types from resistivity logs. Based on acoustic, density, and neutron logs response differences in gas and water layers, effective fluid sensitivity factors are constructed for gas layer identification. From conventional logs, acoustic-neutron porosity difference, density-neutron porosity difference, and triple-porosity ratio are all sensitive parameters to the gas layer. From the NMR logging response mechanism, the density and NMR porosity difference, and T2 geometric mean of the movable fluid are also two sensitive parameters to the gas layer. Based on these parameters, a series of fluid typing charts are constructed and their adaptabilities are analyzed and compared. By contrast, NMR log interpretation is better, and triple-porosity comprehensive method from conventional logs is also effective when NMR logging is not available. Finally, the comprehensive fluid typing strategy by combining some methods for ultra-low porosity tight sandstone is summarized and optimized. This study is another alternative for fluid identification using non-electrical logs.

Recently, microfluidics deformability cytometry has emerged as a powerful tool for high throughput mechanical phenotyping of large populations of cells. These methods characterize cells by their mechanical fingerprints through exerting hydrodynamic forces and monitoring the resulting deformation. These devices have shown great promise for label free cytometry, yet there is a critical need to improve their accuracy and reconcile any discrepancies with other methods, such as atomic force microscopy. In this study, we employ computational fluid dynamics simulations and uncover how the elasticity of frequently used carrier fluids such as methyl-cellulose dissolved in phosphate-buffered saline is significantly influential to the resulting cellular deformation. We conducted CFD simulations that are conventionally used within the deformability cytometry field, which neglect fluid elasticity. Subsequently, we incorporated a more comprehensive model that simulates the viscoelastic nature of the carrier fluid. A comparison of the predicted stresses between these two approaches underscores the significance of the emerging elastic stresses in addition to the well-recognized viscous stresses along the channel. Furthermore, we utilize a two-phase flow model to predict the deformation of a promyelocyte (i.e. HL-60 cell type) within a hydrodynamic constriction channel. The obtained results highlight a substantial impact of the elasticity of carrier fluid on cellular deformation and raise questions about the accuracy of mechanical property estimates derived by neglecting elastic stresses.

Endoscopy has made a significant and noteworthy contribution to the field of medical science and technology. Nevertheless, its potential remains constrained due to the limited availability of rigid or flexible endoscopes. This paper introduces a novel hydraulic actuator based on electrorheological fluid (ERF) as a pivotal advancement in bridging the existing gap within the realm of endoscopy. Following a comprehensive introduction that briefly outlines the electrorheological effect, the subsequent section is dedicated to the elucidation of the actuator’s development process. Challenges arise, particularly in terms of miniaturization and the realization of a hydraulically sealed system with integrated valve electrodes. An internal electrorheological valve system consisting of four valves that are controlled using a pulse-width modulated high voltage was suitable for position control of the antagonistic hydraulic actuators. High-precision stereolithography (SLA) printing has proven practical for manufacturing the actuator components. For functional testing, a test bench was set up in which the actuator follows a setpoint through a PI control loop. The control deviation ranged from 0.6 to 1 degree, with a response time between 6 and 8 seconds. The experiments have demonstrated that, through the use of ERF and integrated valve electrodes, a miniaturized functional actuator can be constructed.

Based on acoustic fluid elements, dynamic analysis was performed on liquid sloshing modes and liquid-filled containers considering the fluid-structure interaction (FSI) effect. The liquid sloshing modes in two-dimensional (2D) and three-dimensional (3D) containers were analyzed, and the results were compared with liquid sloshing modes measured in tests and theoretically calculated modes. This thus verifies correctness of the simulation method based on acoustic fluid elements. Cylindrical liquid-filled containers with different water levels were subjected to modal analysis and dynamic and time-historical analysis. Results show that the finite element analysis (FEA) based on acoustic fluid elements can accurately simulate liquid sloshing modes in liquid-filled containers and vibration characteristics of these containers with different liquid levels. The vibration frequency of liquid-filled containers declines obviously with rising liquid level. The liquid level significantly affects distributions of the maximum displacement, maximum acceleration, and maximum von Mises stress on the sidewall of liquid-filled containers. Numerical simulations based on acoustic fluid elements provides an effective and reliable method for dynamic analysis of liquid-filled containers considering the FSI effect.

Sepsis is defined as life-threatening organ dysfunction caused by a dysregulated host response to an infection. Recent in-vitro studies have investigated the effects of CytoSorb hemoadsorption on endothelial function in sepsis showing a reduction in markers of endothelial dysfunction, but to this day there is a lack of clinical studies showing whether this approach could actually positively influence the disturbed vascular barrier function in septic conditions. We analyzed the data on administered fluid volumes and catecholamines to determine the potential benefit of CytoSorb hemoadsorption therapy on endothelial function in a clinical scenario. We performed a retrospective analysis of 124 septic shock patients who had undergone adjunctive treatment with CytoSorb hemadsorption therapy. We collected volume requirements, and calculated the volume balance within different time periods to obtain an assumption on the stability of the vascular barrier. We also calculated catecholamine requirements. With regard to the entire study cohort our findings revealed a significant reduction in fluid balance at 72 hours (T72) compared to both baseline (T0) and the 24-hour mark (T24). Fluid balances from T72 – T0 were significantly lower in hospital survivors compared to non-survivors. Patients who received a second catecholamine had a significantly lower in-hospital mortality. Our findings showed that use of hemoadsorption therapy results in a reduced positive fluid balance paralleled by reductions in vasopressor needs suggesting a positive effect on endothelial integrity. These results, derived from a large cohort of patients, provide valuable insights that may greatly improve our understanding of the multiple effects of hemoadsorption treatment in septic shock patients.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

This article discusses the results of fluid inclusions study in barite collected at the Jan Mayen vent field area (Troll Wall and Perle &amp; Bruce) and Loki’s Castle vent field of the Mohns Ridge segment of the Arctic Mid-Ocean Ridge. Three mafic-hosted volcanogenic massive sulfide deposits were examined within the active vent fields that adequately correspond to geological settings of ultraslow-spreading ridges and PT-conditions. Hydrothermal sediments were investigated to determine the temperature and salinity of the fluids responsible for barite precipitation. The hydrothermal origin of the barite was confirmed by its morphology. Fluid inclusions are two-phase and homogenized into the liquid phase on heating at temperatures below 287ºC. The salt concentration in fluids trapped in inclusions is 2.6–4.4 wt.% NaCl eq. The crystallization temperatures varied from 276ºС to 119ºС and from 307ºС to 223ºС for the Jan Mayen and Loki’s Castle vent fields, respectively. The data obtained allowed us to confirm evidence of fluid phase separation in the hydrothermal systems and to expand our knowledge of the temperature and salinity of mineral fluids previously known from recent direct measurements during the cruises within the G.O. Sars research vessel. The fluid inclusions data obtained from barites emphasize the fluid features characteristic of volcanogenic massive sulfide deposits, the similarities and differences for the studied hydrothermal sites, and allow comparisons with similar products from other active hydrothermal systems.

In the present study, a numerical model was developed to predict the flow pattern inside a broiler building. The model intends to predict the velocities fields inside the domain and ammonia (NH3) emitted or released by litter from poultry housing. The numerical model developed in Computational Fluid Dynamics (CFD) commercial code, intends to represent a commercial broiler building, and intends to simulate the 3D and heat transfer, in steady state flow. The evaporative cooling pads were also included in the model. The validation of the model was based in experimental measurements obtained in previous studies. The simulations were focused on Summer, Winter and also Mid-Season situation. The numerical results of NH3 concentration were compared with the experimental measurements, and a quite good agreement was verified. The numerical results allowed the characterization of: the inside flow pattern developed for the summer and winter situation; the inside NH3 distribution, and the velocity field distribution inside the broiler building. It was found that NH3 concentration increases along the tunnel, especially in low flow rate imposed from the exhaust fan. Also, it was verified that the low velocities inside domain are no sufficient to remove the gaseous pollutants.

The analogy between the theory of phase transitions in simple fluids and vehicular traffic flow has long been suspected, promising a new level of understanding of urban congestion by standing on one of the firmer foundations in physics. The obstacle has been the interpretation of the thermal energy of the gas-particle system, which remains unknown. This paper proposes the flow of cars through the network as a viable interpretation, where the fundamental diagram for traffic flow would be analogous to the coexistence curve in gas-liquid phase transitions. Thanks to the power-law form of the coexistence curve, it was possible to formalize that the resulting network traffic model belongs to the Kardar-Parisi-Zhang universality class. The scaling relationships arising in this universality class are found to be consistent with West's scaling theory for cities. It is shown that congestion costs (delays + fuel consumption) scale superlinearly with city population, possibly and worryingly more so than predicted by West's theory. Implications for sustainability and resiliency are discussed.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

Lipid metabolism is clearly associated to Parkinson´s disease (PD). Although lipid homeostasis has been widely studied in multiple animal and cellular models as well as in blood derived from PD individuals, the cerebrospinal fluid (CSF) lipidomic profile in PD remains largely unexplored. In this study, we have characterized the CSF lipidomic imbalance between neurologically intact controls (n=10) and PD subjects (n=20). The combination of dual extraction with ultra-performance liquid chromatography-electrospray ionization quadrupole-time-of-flight mass spectrometry (UPLC-ESI-qToF-MS/MS) allowed to monitor 257 lipid species across all samples. Complementary multivariate and univariate data analysis pointed out that glycerolipids (mono-, di-, and triacylglycerides), saturated and mono/polyunsaturated fatty acids, primary fatty amides, glycerophospholipids (phosphatidylcholines, phosphatidylethanolamines), sphingolipids (ceramides, sphingomyelins), N-acylethanolamines and sterol lipids (cholesteryl esters, steroids) were significantly increased in the CSF of PD compared to control group. These results, despite the limitation of being obtained in a small population, demonstrate and extensive CSF lipid remodelling in PD, shedding new light on the deployment of CSF lipidomics as a promising tool to identify potential lipid markers as well as discriminatory lipid species between PD and other atypical parkinsonisms.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

Empirical Colebrook equation from 1939 is still accepted as an informal standard to calculate friction factor during the turbulent flow (4000 < Re < 10⁸) through pipes from smooth with almost negligible relative roughness (ε/D→0) to the very rough (up to ε/D = 0.05) inner surface. The Colebrook equation contains flow friction factor λ in implicit logarithmic form where it is, aside of itself; λ, a function of the Reynolds number Re and the relative roughness of inner pipe surface ε/D; λ = f (λ, Re, ε/D). To evaluate the error introduced by many available explicit approximations to the Colebrook equation, λ ≈ f(Re, ε/D), it is necessary to determinate value of the friction factor λ from the Colebrook equation as accurate as possible. The most accurate way to achieve that is using some kind of iterative methods. Usually classical approach also known as simple fixed point method requires up to 8 iterations to achieve the high level of accuracy, but does not require derivatives of the Colebrook function as here presented accelerated Householder’s approach (3^rd order, 2^nd order: Halley’s and Schröder’s method and 1^st order: Newton-Raphson) which needs only 3 to 7 iteration and three-point iterative methods which needs only 1 to 4 iteration to achieve the same high level of accuracy. Strategies how to find derivatives of the Colebrook function in symbolic form, how to avoid use of the derivatives (Secant method) and how to choose optimal starting point for the iterative procedure are shown. Householder’s approach to the Colebrook’s equations expressed through the Lambert W-function is also analyzed. One approximation to the Colebrook equation based on the analysis from the paper with the error of no more than 0.0617% is shown.

In this paper Brinkman type fluid over an infinite plate between side walls is being investigated. The flow is generated by oscillating shear stress of the bottom plate and the solutions are obtained by using Fourier integral transformation. The obtained results are presented in steady and transient states for both sin and cos shear stresses. The general solutions are reduced to some special cases corresponding, namely to the Brinkman type fluid over an infinite plate and flow of a Newtonian viscous fluid. Graphical illustrations are carried out to have in depth analysis of the involved physical parameters

This paper presents the design and analysis of a novel 3-degree-of-freedom (3-DOF) parallel ma-nipulator equipped with self-sensing Ni-Ti (Nitinol) actuators. The manipulator's architecture and mechanical design are elucidated, emphasizing the integration of Nitinol actuators. The self-sensing technique implemented in a previous work was extended to a 20 mm actuator length, and the actuator was used to design the 3 DOF manipulator. Kinematic analyses were conducted to eval-uate the manipulator's performance under various operating conditions. A dynamic model was implemented for the dynamic dimensioning of the actuators, which work synergistically with a bias spring. The manipulator was realized, and a control strategy was implemented. Experimental tests, although documenting some positioning accuracy issues, show the efficacy and potential applica-tions of the proposed manipulator in robotics and automation systems, highlighting the advantages of self-sensing Nitinol actuators in small parallel manipulator designs.

Rosavin, a phenylpropanoid in Rhodiola rosea's rhizome, an adaptogen, is known for enhancing the body's response to environmental stress. It significantly affects cellular metabolism in health and many diseases, particularly influencing bone tissue metabolism. In vitro, rosavin inhibits osteoclastogenesis, disrupts F-actin rings formation, and lowers osteoclastogenesis-related gene expression (cathepsin K, CTR, TRAF6, TRAP, MMP-9). It also impedes NFATc1, c-Fos, NF-κB, and MAPK signaling pathways, and blocks phosphorylation processes crucial for bone resorption. Moreover, rosavin promotes osteogenesis, osteoblast differentiation and increases Runx2 and OCN expression. In vivo studies show its effectiveness in enhancing BMD in PMOP mice, re-straining osteoclast maturation, and increasing active osteoblast percentage in bone tissue. It modulates mRNA expressions (increasing EEF2 and decreasing HDAC1, thereby activating os-teoprotective epigenetic mechanisms) and alters various serum markers, including decrease of CTX-1, TRAcp5b, RANKL, M-CSF, TRAP, and increase of ALP and OCN. Additionally, when combined with zinc and probiotics, it reduces pro-osteoporotic MMP-3, IL-6, TNF-α, and en-hances anti-osteoporotic IL-10 and TIMP3 expressions. This paper aims to systematically review rosavin's impact on bone tissue metabolism, exploring its potential in osteoporosis prevention and treatment, and suggesting future research directions.

This review explores the transformative impact of sensor technologies in early disease detection. It highlights recent advancements in nanotechnology-based sensors, particularly focusing on their applications in identifying disease biomarkers at early stages. The integration of these sensors with artificial intelligence for predictive analytics in healthcare is also discussed. Applications in cancer, infectious diseases, and chronic disease management underscore their diverse utility. Challenges in sensor technology adoption and future directions, including multiplexed sensors and wearable devices, are examined. This review underscores sensors' potential in enhancing disease management and patient outcomes.

Herpesvirus is a prevalent pathogen that primarily infects human epithelial cells and has the ability to reside in neurons. In the field of otolaryngology, herpesvirus infection primarily leads to hearing loss and vestibular neuritis, and is considered the primary hypothesis regarding the pathogenesis of vestibular neuritis. In this review, we provide a summary of the effects of herpes virus on cellular processes in both host cells and immune cells, with a focus on HSV-1 as illus-trative examples.

Energy demand has exponentially increased with the increase in the world population and ur-banization. Renewable energy is clean, renewable, and environmentally friendly. Hydrogen production through Proton Exchange Membrane (PEM) electrolyzer is an efficient way to produce renewable energy. The efficiency and energy consumption of the PEM electrolyzer depends on the feed water quality. In this report, we study the effect of pH, TDS, and conductivity on hydrogen production as well as energy consumption during the process. pH values (3, 7, 9), TDS values (300ppm, 600ppm, 900ppm), and conductivity values (30mS/cm, 70mS/cm, 100mS/cm) were studied to understand and optimize the hydrogen production using PEM electrolyzer. The in-vestigations showed that hydrogen production is significantly affected by pH, total dissolved solids, and conductivity, and the best levels of each variable were identified by extensive testing. The findings show both the scientific significance of proton exchange electrolysis in meeting the growing energy demands of society as well as the importance of knowing the influence that di-verse conditions have on the creation of hydrogen. Our research, in general, contributes to the expanding body of scientific knowledge on the topic of the effective production of hydrogen and offers useful insights for the continuation of investigation in this field.

The article is aimed at a brief comparison and analysis of the results of queries to IEEE Xplore and the leading abstract databases Scopus and Web of Science to identify research trends. Some errors in the Author Keywords in Web of Science have been revealed. Therefore, a more detailed analysis was conducted by comparing different types of key terms for IEEE Xplore and Scopus platforms only. I used IEEE Access journal metadata as indexed on both platforms. The sample match for IEEE Xplore and Scopus was achieved by comparing DOI. The IEEE Xplore metadata contains more types of key terms, which provides an advantage in analyzing research trends. Using NSPEC Controlled Terms from expert-compiled vocabulary provides a more stable data, which gives an advantage when considering the change of terms over time. Apriori, an algorithm for finding association rules, has been used to compare co-occurrence of terms for a more detailed description of sample subjects on both platforms. VOSviewer was used to analyze trends in scientific research based on IEEE Xplore data. The 2011-2021 ten-year period was divided into two sub-intervals for comparing the occurrence of Author Keywords, IEEE Terms, and NSPEC Controlled Terms. Using the IEEE conference proceedings bibliometric data, I illustrated the importance of context in estimating the rate of growth of publishing activity on a topic of interest.

Intravitreal injection is the gold standard therapeutic option for posterior segment pathologies, and long-lasting release is necessary to avoid reinjections. There is no effective intravitreal treatment for glaucoma or other optic neuropathies in daily practice, nor is there a non-invasive method to monitor drug levels in the vitreous. Here we show that a glaucoma treatment combining a hypotensive and neuroprotective intravitreal formulation (IF) of brimonidine-Laponite (BRI/LAP) can be monitored non-invasively using vitreous imaging captured with optical coherence tomography (OCT) over 24 weeks of follow-up. Qualitative and quantitative characterization was achieved by analysing the changes in vitreous (VIT) signal intensity, expressed as a ratio of retinal pigment epithelium (RPE) intensity. Vitreous hyperreflective aggregates mixed in the vitreous and tended to settle on the retinal surface. Relative intensity and aggregate size progressively decreased over 24 weeks in treated rat eyes as the BRI/LAP IF degraded. VIT/RPE relative intensity and total aggregate area correlated with brimonidine levels measured in the eye. The OCT-derived VIT/RPE relative intensity may be a useful and objective marker for non-invasive monitoring of BRI/LAP IF.

Besides the increase in global energy demand, access to clean energy, reduction in greenhouse gas emissions caused by conventional power generation sources, energy security, and availability of electricity in remote villages in emerging nations are some of the factors that foster the use of renewable energy sources (RESs) in generating electricity. One of the aims of initiating microgrids (MGs) is to maximize the benefits of RES and alleviate the associated grid integration issues. Microgrids are made up of RES connected to electrical loads within clearly delineated electrical limits that operate as individual controllable units on the electrical network. It can operate in-dependently as well as in connection with the grid. The paper presents an overview of microgrids and investigates the system's performance when connected to and disconnected from the grid. Furthermore, in both modes of operation, the functioning and behavior of system components such as the bidirectional DC-DC converter and energy storage system (ESS) were evaluated. The architecture of the proposed microgrid consists of a small hydropower plant, a wind farm, and a battery energy storage system (BESS). The microgrid under investigation is modeled and simu-lated using MATLAB and Simulink.

We aimed to determine if infection-associated urine biomarkers can differentiate true urinary tract infection (UTI) from non-UTI controls. Midstream clean-catch urine samples were collected from asymptomatic volunteers and symptomatic subjects > 60 years old diagnosed with presumptive UTI in a specialty setting. Microbial identification and density were assessed using multiplex PCR/pooled antibiotic susceptibility test (M-PCR/P-AST) and standard urine culture (SUC). Three biomarkers (NGAL, IL-8, and IL-1β) were measured in the same urine specimens. Definitive UTI cases were symptomatic and had positive microorganism detection by SUC and M-PCR, while definitive non-UTI cases were asymptomatic volunteers regardless of microbial detection. We observed a strong positive correlation (R2 ≈ 1) between microbial density and the biomarkers NGAL, IL-8, and IL-1β. Biomarker consensus criteria of two or more positive biomarkers had sensitivity 90.2%, specificity 91.2%, positive predictive value (PPV) 91.7%, negative predictive value (NPV) 89.7%, accuracy 90.7%, positive likelihood ratio of 10.28, and negative likelihood ratio of 0.11 in differentiating definitive UTI from non-UTI cases, regardless of microbial density. NGAL, IL-8, and IL-1β showed a significant elevation in symptomatic cases with positive microbe identification compared to asymptomatic cases with or without microbe identification. Biomarker consensus exhibited high accuracy in distinguishing UTI from non-UTI cases.

Thyroid hormones (THs) are essential for normal brain development, influencing neural cell differentiation, migration, and synaptogenesis. Multiple endocrine-disrupting chemicals (EDCs) are found in the environment, raising concern for their potential effects on thyroid hormone signaling and the consequences on neurodevelopment and behavior. While most research on EDCs investigates the effects of individual chemicals, human health may be adversely affected by a mixture of chemicals. Many compounds belonging to a wide range of chemical classes have been identified as EDCs, notably those affecting thyroid hormone signaling. We hypothesized that embryonic exposure to a mixture of chemicals (containing phenols, phthalates, pesticides, heavy metals, perfluorinated -, polychlorinated, and polybrominated compound) commonly found in the human amniotic fluid could lead to altered brain development to assess its effect on thyroid hormone signaling and neurodevelopment in an amphibian model (Xenopus laevis), highly sensitive to thyroid disruption. Newly hatched tadpoles were exposed for eight days to either TH (thyroxine, T4 10nM) or the amniotic mixture (1x concentration) and gene expression was analyzed in the brains of exposed tadpoles using both RT-qPCR and RNA sequencing. Results indicate that whilst some overlap on TH-dependent genes exist, T4 and the mixture have different gene signatures. Immunohistochemistry showed increased proliferation in the brains of T4-treated animals whereas no difference was observed for the amniotic mixture. Further, we demonstrated diminished tadpoles’ motility in response to T4 and mixture exposure. As the individual chemicals composing the mixture are considered safe, these results highlight the importance of examining the effects of mixtures to improve risk assessment

(1) Background: Sensing of critical events or flow signatures in nature often presents itself as a coupled interaction between a fluid and arrays of slender flexible beams, such a wind-hairs or whiskers. It is hypothesized that important information is gained in highly noisy environments by the inter-correlation within the array. (2) Methods: The present study uses a model sea lion head with artificial whiskers in the form of slender beams (optical fibres), which are subjected to a mean flow with overlaid turbulent structures generated in the wake of a cylinder. Motion tracking of the array of fibres is used to analyse the correlation of the bending deformations of pairs of fibres. (3) Results: Cross-correlation of the bending signal from tandem pairs of whiskers proves that the detection of vortices and their passage along the animals head is possible even in noisy environments. The underlying pattern, during passage of a vortex core, is a jerk-like response of the whiskers, which can be found at later arrival-times in similar form in the downstream whisker's response. (4) Conclusion: Coherent vortical structures can be detected from cross-correlation of pairs of cantilever-beam like sensors even in highly turbulent flows. Such vortices carry important information within the environment, e.g. the underlying convection velocity. More importantly in nature, these vortices are characteristic elementary signals left by prey and predators. The present work can help to further develop flow, or critical event, sensory systems which can overcome high noise levels due to the proposed correlation principle.

Three-dimensional (3D) facies and petrophysical models were generated from previously published data of carbonate strata in the Dam Formation (eastern Saudi Arabia) to quantitatively investigate, describe, understand, model, and predict the permeability anisotropy of tidal flat carbonate within a sequence stratigraphic framework. The resulting 3D models were used to conduct fluid flow simulations to demonstrate how permeability anisotropy influences the production of hydrocarbons and ultimately affects decisions concerning future drilling in the exploration and development of carbonate reservoirs that have tidal flat strata. The constructed 3D facies model consists of four lithofacies associations, two of which were grain-dominated associations and two of which were mud-dominated associations. These lithofacies associations varied spatially in four reservoir zones (zones 1 to 4), which represent two fourth-order sequences in the uppermost part of the Dam Formation. Zones 1 and 3 consist of transgressive parasequences, and zones 2 and 4 consist of the regressive parasequences of these sequences. The 3D porosity and permeability models have a coherent match with the distribution of the lithofacies and the stratigraphic framework of the Dam Formation. The results suggested that the permeability anisotropy in zones 1 and 3 is controlled by the occurrence of the grain-dominated lithofacies associated with tidal flat channels. This lithofacies association overlies the sequence boundaries of sequences 1 and 3, forms reservoir bodies with relatively high permeability values, and is elongated perpendicular to the shoreline of the depositional environments. In contrast, permeability anisotropy in zones 2 and 4 is thought to be controlled by the occurrence of the grain-dominated lithofacies associated with the oolitic shoal. This lithofacies association overlies the maximum flooding surface of sequences 2 and 4, forms reservoir bodies with relatively high permeability values, and is elongated parallel to the shoreline of the depositional environments. Fluid flow simulation results suggested that the trend in hydrocarbon production from the constructed 3D models depends on permeability anisotropy in each reservoir zone. Thus, recognizing trends in permeability anisotropy, which might be predicted using sequences stratigraphy, could help to identify potential areas for future drilling.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

The goal of newborn screening is to improve health outcomes by identifying and treating affected newborns. This manuscript provides an overview of a data tool to facilitate the longitudinal collection of health information on newborns diagnosed with a condition through NBS. The Newborn Screening Translational Research Network (NBSTRN) developed the Longitudinal Pediatric Data Resource (LPDR) to capture, store, analyze, visualize, and share genomic and phenotypic data over the lifespan of NBS identified newborns to facilitate understanding of genetic disease, and to assess the impact of early identification and treatment. NBSTRN developed a consensus-based process using clinical care experts to create, maintain, and evolve question and answer sets organized into common data elements (CDEs). The LPDR contains 24,172 core and disease-specific CDEs for 118 rare genetic diseases, and the CDEs are being made available through the NIH CDE Repository. The number of CDEs for each condition average of 2,200 with a range from 69 to 7,944. The LPDR is used by state NBS programs, clinical researchers, and community-based organizations. Case level, de-identified data sets are available for secondary research and data mining. The development of the LPDR for longitudinal data gathering, sharing, and analysis supports research and facilitates the translation of new discoveries into clinical practice.

Our investigations show that electrochemical corrosion of copper is faster than electrochemical corrosion of aluminium at temperatures below 100oC. Literature data analysis shows that the Al atoms diffuse faster than the Cu atoms at temperatures higher than 475oC, Al rich intermetallic compounds (IMCs) are formed faster in the Cu-Al system, and the Kirkendall plane shifts toward Al side. Electrochemical corrosion occurs due to electric current and due to diffusion. An electronic devise working time, for example, depends on initial copper cover thickness on aluminium wire, connected to the electronic devise, temperature, and volume and dislocation pipe diffusion coefficients, so copper, iron, and aluminium electrochemical corrosion rates are investigated experimentally at room temperature and at temperature 100oC. Intrinsic diffusivities ratios of copper and aluminium at different temperatures and diffusion activation energies in the Cu-Al system are calculated by proposed here methods using literature experimental data. Dislocation pipe and volume diffusion activation energies of pure iron are calculated separately by earlier proposed method using literature experimental data. Aluminium dissolved into NaCl solution as the Al3+ ions at room temperature and at temperature 100oC, iron dissolved into NaCl solution as the Fe2+ (not Fe3+) ions at room temperature and at temperature 100oC, copper dissolved into NaCl solution as the Cu+ ions at room temperature and as the Cu+ and the Cu2+ ions at temperature 100oC. It is founded experimentally that copper corrosion is higher than aluminium corrosion, and ratio of electrochemical corrosion rates, kCu/kAl>1, decreases with temperature increasing, although iron electrochemical corrosion rate doesn’t depend on temperature below 100oC. It is obvious, because melting point of iron is more higher then melting point of copper or aluminium. It is calculated that copper electrochemical corrosion rate is approximately equal to aluminium electrochemical corrosion at temperature about 300oC, so copper can dissolve into NaCl solution mostly as the Cu2+ ions at temperature about 300oC. Ratio of intrinsic diffusivities, DCu/DAl <1, increases with temperature increasing, and intrinsic diffusivity of aluminium could be approximately equal to intrinsic diffusivity of copper at temperature about 460oC.

Machine learning (ML) based on neural network (NN) facilitates data-driven techniques for handling large amounts of data, either obtained through experiments or simulations at multiple spatio-temporal scales, thereby finding the hidden patterns underlying these data and promoting efficient research methods. The main purpose of this paper is to extend the capabilities of a new solver, called realFluidReactingNNFoam, under development at University of Perugia in OpenFOAM with NN algorithm for replacing complex real-fluid thermophysical property evaluations, using the approach of coupling OpenFOAM and Python-trained NN models. Currently, NN models are trained against data generated using the Peng-Robinson equation of state (PR-EoS) assuming mixture frozen temperature. The OpenFOAM solver, where needed, calls the NN models in each grid-cell with appropriate inputs, and the returned results are used and stored in suitable OpenFOAM data structures. Such inference for the thermophysical properties is achieved via the “Neural Network Inference in C made Easy” (NNICE) library, which proved to be very efficient and robust. The overall model is validated considering a liquid-rocket benchmark comprised of liquid-oxygen (LOX) and gaseous-hydrogen (GH2) streams. The model accounts for real-fluid thermodynamics and transport properties, making use of the PR-EoS and the Chung transport models. First, the development of a real-fluid model (RFM) with artificial neural network is described in detail. Then, the numerical results of the transcritical mixing layer (LOX/GH2) benchmark are presented and analyzed in terms of accuracy and computational ef-ficiency. Results of the overall implementation indicate that the combined OpenFOAM and ML approach provides a speed-up factor higher than seven, while preserving the original solver accuracy.

This paper provides the numerical investigation of two-dimensional stochastic Navier-Stokes equation driven by additive white noises. The vorticity-stream function method is presented to calculate the incompressible fluid flow. In order to solve the formulation of steam function equation, we propose a Crank-Nicolson Fourier pseudo-spectral method. Numerical results obviously show that the presence of stochastic forcing can have an impact upon the shapes of vortex in fluid flow. To a certain extent, the phenomenon of eddy shedding and the formation of some new vortex in a random medium can be observed, which make it possible for us to conduct optimal control experiments in the development of vortex structures.

Innovations in drug delivery systems are crucial for enhancing therapeutic efficiency. Our research presents a novel approach based on Electro-fluid dynamic atomization (EFDA) to fabricate core-shell monophasic particles (CSMp) from sodium alginate blends of varying molecular weights. This study explores the morphological characteristics of these particles in relation to material properties and process conditions, highlighting their potential in drug delivery applications. A key aspect of our work is the development of a mathematical model that simulates the release kinetics of small molecules, specifically sodium diclofenac. By assessing the diffusion properties of different molecules and gel formulations through transport and rheological models, we have created a predictive tool for evaluating the efficiency of these particles in drug delivery. Our findings underscore two critical independent parameters for optimizing drug release: the external shell thickness and the diffusivity ratios within the dual layers. This allows for precise control over the timing and intensity of the release profile. The study advances our understanding of EFDA in the fabrication of CSMp and offers promising avenues for enhancing drug delivery systems by tailoring release profiles through particle characteristic manipulation.

The continuous casting tundish is non-isothermal due to heat losses and temperature variation from the inlet stream generating relevant convection forces. This condition is commonly avoided through qualitative fluid dynamic analysis only. This work searches to establish the conditions for which non-isothermal simulations are mandatory or for which isothermal simulations are enough to accurately describe the fluid dynamics inside the tundish by quantifying the buoyant and inertial forces. The mathematical model, simulated by CFD software, considers the Navier-Stokes equations, the realizable k- model for solving the turbulence, and the Lagrangian discrete face to track the inclusion trajectories. The results show that temperature does not significantly impact the volume fraction percentages or the mean residence time results, nevertheless, bigger velocity magnitudes under non-isothermal conditions than in isothermal conditions and noticeable changes in the fluid dynamics between isothermal and non-isothermal cases in all the zones where buoyancy force dominates over inertial forces were observed. Because of the results, it is concluded that isothermal simulations can accurately describe the flow behavior in tundishes when the flow control devices control the fluid dynamic, but the simulation without control devices or with a weak fluid dynamic dependence on the control devices requires non-isothermal simulations.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

The main object of this work is to establish the existence and uniqueness of a solution to the 3D Navier-Stokes (NS) system for an incompressible fluid with viscosity. The nonlinearity of the NS system, as well as the need to estimate velocity and pressure for every value of the viscosity parameter [1] make them challenging to solve. In this regard, in the present work, we study the Navier-Stokes system, which describe the flow of a viscous incompressible fluid and the solution was obtained for velocity and pressure in an analytical form. In addition, the found pressure distribution law, which is described by a Poisson type equation and plays a fundamental role in the theory of Navier-Stokes systems in constructing analytic smooth (conditionally smooth) solutions.

Optimization of Magnetohydrodynamics parameters on the velocity profile and temperature distribution of incompressible fluid flow on a porous channel was evaluated. The fluid flow was considered to be unsteady, incompressible and flowing in 2-D in porous channel. The effects of magnetic parameter, Darcy’s number and fluid pressure on velocity profiles, and the effect of variable viscosity and Eckert number on temperature distribution in incompressible fluid flow were determined. The flow was considered to be in a channel running along the x-axis on which the magnetic field exist and finally along the y-axis on the porous part of the channel. The resulting model equations were solved by Finite Difference Method (FDM) in MATLAB software. Analysis of results indicated that increasing Darcy’s number and fluid pressure leads to increase in fluid velocity profile, while increasing magnetic parameter decreases fluid velocity profile. Also, it was observed that increase in both Eckert number and fluid viscosity lead to increase in temperature distribution. Optimization in temperature was achieved by increasing the magnetic field while viscosity was optimized by increasing the length of the porous part of the channel. This study will helpful to contribute alternative equations and methodology to engineering and in factories where getting the MHD parameters optimally is the main objective, particularly on temperature, velocity and pressure.

An overview is presented of several diverse branches of work in the area of effectively 2D fluid equilibria which have in common that they are constrained by an infinite number of conservation laws. Broad concepts, and the enormous variety of physical phenomena that can be explored, are highlighted. These span, roughly in order of increasing complexity, Euler flow, nonlinear Rossby waves, 3D axisymmetric flow, shallow water dynamics, and 2D magnetohydrodynamics. The classical field theories describing these systems bear some resemblance to perhaps more familiar fluctuating membrane and continuous spin models, but the fluid physics drives these models into unconventional regimes exhibiting large scale jet and eddy structures. From a dynamical point of view these structures are the end result of various conserved variable forward and inverse cascades. The resulting balance between large scale structure and small scale fluctuations is controlled by the competition between energy and entropy in the system free energy, in turn highly tunable through setting the values of the conserved integrals. Although the statistical mechanical description of such systems is fully self-consistent, with remarkable mathematical structure and diversity of solutions, great care must be taken because the underlying assumptions, especially ergodicity, can be violated or at minimum lead to exceedingly long equilibration times. Generalization of the theory to include weak driving and dissipation (e.g., non-equilibrium statistical mechanics and associated linear response formalism) could provide additional insights, but has yet to be properly explored.

The onset of the thermal instability is investigated in a porous channel with plane parallel boundaries saturated by a non–Newtonian shear–thinning fluid and subject to a horizontal throughflow. The Ellis model is adopted to describe the fluid rheology. Both horizontal boundaries are assumed to be impermeable. A uniform heat flux is supplied through the lower boundary, while the upper boundary is kept at a uniform temperature. Such an asymmetric setup of the thermal boundary conditions is analysed via a numerical solution of the linear stability eigenvalue problem. The linear stability analysis is developed for three–dimensional normal modes of perturbation showing that the transverse modes are the most unstable. The destabilising effect of the non-Newtonian shear–thinning character of the fluid is also demonstrated as compared to the behaviour displayed, for the same flow configuration, by a Newtonian fluid.

This paper proposes a procedure for predicting the actual wind speed for flow over complex terrain with CFD. It converts a time-series of wind speed data acquired from field observations into a time-series of actual scalar wind speed by using non-dimensional wind speed parameters which are determined beforehand with the use of CFD output. The accuracy and reproducibility of the prediction procedure were examined by simulating the flow with CFD with the use of high resolution (5 m) surface elevation data for the Noma Wind Park in Kagoshima Prefecture, Japan. The errors of the predicted average monthly wind speeds relative to the observed values were less than approximately 20%.

KLHL genes and the related KBTBD genes encode components of the Cullin-E3 ubiquitin ligase complex and typically target tissue-specific proteins for degradation, thereby affecting differentiation, homeostasis, metabolism, cell signaling, and the oxidative stress response. Despite their importance in normal cell function and in disease (KLHL40, KLHL41, KBTBD13, KEAP1, and ENC1), previous studies that examined epigenetic factors affecting transcription were predominantly limited to promoter DNA methylation. Using diverse tissue and cell culture whole-genome profiles, we examined 17 KLHL or KBTBD genes preferentially expressed in skeletal muscle or brain to identify tissue-specific enhancer and promoter chromatin, open chromatin (DNaseI hypersensitivity), and DNA hypomethylation. Sixteen of the 17 genes displayed muscle- or brain-specific enhancer chromatin in their gene bodies, and most exhibited specific intergenic enhancer chromatin as well. Seven genes were embedded in a super-enhancer. The enhancer chromatin regions typically displayed foci of DNA hypomethylation at peaks of open chromatin. In addition, we found evidence that gene neighbors (HHATL and FBXO32) of KLHL40 and KLHL38 harbor enhancer chromatin that likely upregulates the adjacent KLHL gene. Many KLHL/KBTBD genes had tissue-specific promoter chromatin at their 5’ ends, but surprisingly, two (KBTBD11 and KLHL31) had constitutively unmethylated promoter chromatin in their 3’ exons that overlaps a retrotransposed KLHL gene. Our findings demonstrate the importance of expanding epigenetic analyses beyond the 5’ ends of genes in studies of normal and abnormal gene regulation.

Background and objectives: Unrestricted kinematic alignment total knee arthroplasty (KA-TKA) with a soft tissue respecting technique (STRT) is a soft tissue-dependent tibial resection entailing restoration of the original soft tissue tension using ligamentotaxis after resurfacing the femur, based on the concept of restoring the native or pre-osteoarthritis alignment in each patient. However, there is no consensus on the indications of unrestricted KA-TKA with STRT. We modified the STRT, followed by investigation of the effects of surgery on the postoperative hip-knee-ankle angle (HKAA). Materials and Methods: We retrospectively analyzed the clinical background data, including the preoperative and postoperative HKAA, of 87 patients who underwent unrestricted KA-TKA with the modified STRT. Univariate and multivariate analyses were performed to determine the factors affecting the postoperative HKAA. A receiver operating characteristic (ROC) curve was plot-ted to investigate the change in the cut-off values of preoperative HKAA with respect to the safe zone of the postoperative HKAA. We generated two regression models, the linear regression model and generalized additive model (GAM) using machine learning, to predict the postopera-tive HKAA. Results: Univariate and multivariate analyses revealed the preoperative HKAA as the factor most relevant to the postoperative HKAA. ROC analysis revealed that the preoperative HKAA exhibited high predictive utility, with a cut-off value of -10°, when the safe range of postoperative HKAA was set at ± 5°. The GAM was the superior machine learning model, indicating a non-linear association between the preoperative and postoperative HKAA. Patients with preoperative HKAAs ranging from -18° to 4° were more likely to fall within the ± 5° safe range of the postoperative HKAA. Conclusions: The preoperative HKAA influences the postoperative HKAA in unrestricted KA-TKA with the modified STRT. Machine learning using the GAM may contribute to the selection of patients eligible for the surgical approach.

One of the important research directions in the field of photovoltaics is integration with construction. The integration of solar cell systems with a building can reduce installation costs and help optimize the used space. One of the interesting types of cells is dye-sensitized solar cells. In addition to their interesting properties, they also have aesthetic value. In the classic arrangement, they are constructed using glass with a transparent conductive layer (TCL). This article describes replacing a classic glass counter electrode with an electrode based on a ceramic tile and nickel foil. This solution makes it possible to expand their construction applications. The advantage of this solution is full integration with construction while simultaneously generating electricity. A dye-sensitized solar cell was built layer-by-layer on ceramic tile and nickel foil. An atomization method was used to deposit fluorine-doped tin oxide, and then a screen printing method was used to deposit a platinum layer. The electrical parameters of the manufactured DSSCs with and without a counter electrode tile were characterized by measuring their current-voltage characteristics under standard AM 1.5 radiation. A dye-sensitized solar cell integrated with ceramic tiles and nickel foil was produced and displayed an efficiency of over 4%.

Abstract: The promise of regenerative medicine and tissue engineering is founded on the ability to regenerate diseased or damaged tissues and organs into functional tissues and organs or the creation of new tissues and organs altogether. In theory, all damaged and diseased tissues and organs can be regenerated or created using different configurations and combinations of extracellular matrix, cells and inductive biomolecules. Currently, regenerative medicine and tissue engineering can allow the improvement of patients’ quality of life through availing novel treatment options. Tissues and organs have a specific ECM, with specific proteins and factors released by cells residing within the local microenvironment. The coupling of regenerative medicine and tissue engineering field with 3D printing is revolutionizing the treatment of patients in a huge way. 3D bioprinting allows the proper placement of cells and ECMs, allowing the recapitulation of native microenvironments of tissues and organs. 3D bioprinting utilizes different bioinks made up of different formulations of ECM/biomaterials, biomolecules and even cells. The choice of the bioink used during 3D bioprinting is very important as properties such as printability, compatibility and physical strength influence the final construct printed. The extracellular matrix (ECM) provides both physical and mechanical microenvironment needed by cells to survive and proliferate. Decellularized ECM bioink contains biochemical cues from the original native ECM and also the right proportions of ECM proteins. Different techniques and characterization methods are used to derive bioinks from several tissues and organs and to evaluate their quality. This review discusses the uses of decellularized ECM bioinks and argues that they represent the most biomimetic bioinks available. In addition, we briefly discuss some polymer-based bioinks utilized in 3D bioprinting.

Acinetobacter baumannii is a nosocomial pathogen capable of causing serious infections associated with high rates of morbidity and mortality. Due to its antimicrobial drug resistance profile, A. baumannii is categorized as an urgent priority pathogen by the Centers for Disease Control and Prevention in the United States and priority group 1 critical microorganism by the World Health Organization. Understanding how A. baumannii adapts to different host environments may provide critical insights into strategically targeting this pathogen with novel antimicrobial and biological therapeutics. Exposure to human fluids was previously shown to alter the gene expression profile of a highly drug susceptible A. baumannii strain A118 leading to persistence and survival of this pathogen. Herein, we explore the impact of human pleural fluid (HPF) and human serum albumin (HSA) on the gene expression profile of a highly multi-drug resistant strain of A. baumannii AB5075. Differential expression was observed for ~30 genes, whose products are involved in quorum sensing, quorum quenching, iron acquisition, fatty acid metabolism, biofilm formation, secretion systems and type IV pilus formation. Phenotypic and further transcriptomic analysis using quantitative RT-PCR confirmed RNA-seq data and pointed out a distinctive role of HSA as the molecule involved in A. baumannii response.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

In recent years, there has been a growing interest in the preoperative modeling of fluid-structure interaction in the treatment of cerebral aneurysms. In this study, we investigate two cases involving laminar incompressible fluid flow interacting with hyperelastic materials (a vertical flap and aneurysm walls) under the effect of fluid flow. We present a finite element method (FEM) for these prototypical two-dimensional ($2D$) configurations, taking into account the complex flows and deformation of the variant's structure models. We use an Arbitrary Lagrangian-Eulerian (ALE) formulation in a continuum, fully monolithic coupled way, and discretize the fluid and solid domains using the quadratic LBB stable $P_2P_1$ finite element pair to approximate the displacement, velocity, and pressure spaces independently. The resulting discretized form of the nonlinear algebraic system is linearized using a variant of Newton's procedure, and the Jacobian matrices are approximated via the divided difference method. The resulting linear systems are solved using a direct solver MUMPS. We evaluate hydrodynamic forces such as drag and lift coefficients for nonlinear elastic material models, including Saint-Venant Kirchoff, Neo-Hookean, and Mooney-Rivlin (2 parameters) separately. To gain more physical insight into the problem, we verify the computed results by comparing the velocity, viscosity, and pressure fields. Our aim is to qualitatively analyze the changes in the mechanics of the wall behavior of the elasticity of the flap vs. the complexity of deformation, interface, details for prototypical flow situations, corresponding displacement, and deformation. We also provide a physical interpretation of blood flow magnitude and basic hemodynamic phenomena of wall shear stresses (WSS) in aneurysma and the range of deformation. Overall, this study presents a comprehensive approach to modeling fluid-structure interaction in cerebral aneurysms, which could help in the development of more effective treatment strategies.

The combination of artificial intelligence algorithms and numerical methods has recently become popular in the prediction of macroscopic and microscopic hydrodynamics parameters of bubble column reactors. The multi inputs and outputs machine learning can cover small phase interactions or large fluid behavior in industrial domains. This numerical combination can develop the smart multiphase bubble column reactor with the ability of low-cost computational time. It can also decrease case studies for the optimization process when big data is appropriately used during learning. There are still many model parameters that need to be optimized for a very accurate artificial algorithm, including data processing and initialization, the combination of inputs and outputs, number of inputs and model tuning parameters. For this study, we aim to train four inputs big data during learning process by an adaptive neuro-fuzzy inference system or adaptive-network-based fuzzy inference system (ANFIS) method, and we consider the superficial gas velocity as one of the input variables, while for the first time, one of the computational fluid dynamics (CFD) outputs named gas velocity is used as an output of the artificial algorithm. The results show that the increasing number of input variables improves the intelligence of the ANFIS method up to , and the number of rules during learning process has a significant effect on the accuracy of this type of modeling. The results also show that propper selection of model parameters results in more accuracy in prediction of the flow characteristics in the column structure.

The present work is focused on the numerical solution of the complete energy equation used in fluid film lubrication. The work was motivated by the fact the complete energy equation has no analytic solution that could be used for validations. Its accuracy and computation time are related to the employed numerical method and to the grid resolution. The natural discretization method (NDM) applied on different grids is systematically compared with the spectral method (the Lobatto Point Colocation Method or LPCM) with different polynomial degrees. A one dimensional inclined slider is used for the numerical tests and the energy equation is artificially decoupled from Reynolds. This approach enables to focus all the attention on the numerical solution of the energy equation. The results show that the LPCM is one or two orders of magnitudes more efficient than the NDM in terms of computation time. The energy equation is then coupled with Reynolds equation in a thermo-hydrodynamic analysis of the same 1D slider; the numerical results confirm again the efficiency of the LPCM. A thermo-hydrodynamic analysis of a two-lobe journal bearing is then presented as a practical application.

We discuss the influence played by different statistical models in the prediction of porosity and litho-fluid facies from logged and post-stack inverted acoustic impedance (Ip) values. We compare the inversion and classification results obtained under three different a-priori statistical assumptions: an analytical Gaussian distribution, an analytical Gaussian-mixture model and a non-parametric mixture distribution. The first model assumes Gaussian distributed porosity and Ip values, thus neglecting their facies-dependent behaviour caused by different lithologic and saturation conditions. Differently, the other two statistical models relate each component of the mixture to a specific litho-fluid facies, so that the facies-dependency of porosity and Ip values is taken into account. Blind well tests are used to validate the final predictions, whereas the analysis of the maximum-a-posteriori (MAP) solutions, the coverage ratio and the contingency analysis tools are used to quantitatively compare the inversion outcomes. This work points out that the correct choice of the statistical petrophysical model could be crucial in reservoir characterization studies. Indeed, for the investigated zone it turns out that the simple Gaussian model constitutes an oversimplified assumption, while the two mixture models provide more accurate results, although the non-parametric one yields slightly superior predictions with respect to the Gaussian-mixture assumption.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

Plants produce specific structures constituting a barrier hindering penetration of pathogens, while they also produce substances inhibiting pathogen growth . These compounds are secondary metabolites, such as phenolics, terpenoids, sesquiterpenoids, resins, tannins and alkaloids. Bioactive compounds are secendary metabolities from trees and shrubs are used in medicine, herbal medicine and cosmetology. To date fruits and flowers of exotic trees and shrubs have been primarily used as sources of bioactive compounds. In turn, search for new sources of bioactive compounds is currently focused on native plant species due to its availability. Application of such raw material needs to be based on knowledge of their chemical composition, particularly health-promoting or therapeutic compounds. Research conducted to date on European trees and shrubs has been scarce. This paper presents results of literature studies conducted to systematise knowledge on bioactive compounds found in trees and shrubs native to central Europe. The aim of this review providing available information on the subject is to indicate gaps in the present knowledge.

Abstract: The aim of this study is to emphasize on the clinical uses of amniotic membrane (AM) in multiple ocular disorders. AM possesses many properties including promotion of epithelialization, anti-fibrotic, anti-apoptotic, anti-angiogenic properties. Epithelial wound healing on the eye surface is promoted due to several epidermal and keratocyte growth factors as well as by its anti-inflammatory and anti-scarring effects due to interleukin-10, interleukin-1 receptor antagonists and inhibition of transforming growth factor- beta (TGF-β) signal transduction by AM in the corneal and conjunctival fibroblasts respectively. It plays a crucial role by functioning as a substitute of basement membrane (BM) and as a temporary graft material. It is not only being used as an eye graft but also its extract can be used as an eye drop for corneal and external eye diseases. So its proper preparation, preservation and clinical application can bring a revolutionary change in the treatment of different ocular disorders.

Failures in hydraulic systems in offshore wind turbines represent an enormous challenge for manufacturers and operators, as the pitch system statistically is one of the subsystems contributing the most to the downtime of the turbines, which is the case for both electrical and hydraulic pitch systems. However, the complex failure mechanisms of the various different hydraulic components mean that, typically, the critical components of hydraulic systems must be tested to better understand the failure mechanisms. Nonetheless, conventional testing procedures are lengthy and costly. Accelerated testing plays a critical role as it can mimic hydraulic system failure mechanisms in a shorter period. However, the lack of standardized test methods and detailed knowledge about the failure-accelerating effects complicates the process. Therefore, this paper offers a comprehensive examination of approaches applicable to conducting accelerated tests on hydraulic systems. It identifies and discusses five primary component types or sub-components related to the acceleration of testing in hydraulic systems being: pumps, cylinders, seals, valves, and hoses. Each section references studies that delve into accelerated testing methodologies for these individual components. Furthermore, within each component, a concise overview of the current techniques is provided, followed by a discussion and summary based on the state of the art.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

This study proposes a customized industrial nozzle for generating impulsive air jets. It is installed on an automatic machine where wine caps are stacked and shot consecutively into a rotating cylinder by an air jet. This process is very noisy; hence, this study aimed to investigate possible geometric variations of the nozzle that can reduce the emitted noise. First, the nozzle was tested in a laboratory to measure the air consumption at different supply pressures. Subsequently, 3D models of the nozzle and its variations were created and used for computational fluid dynamics simulations. Different boundary conditions were set, first to validate the model and compare it with the experimental test results, and then to simulate the real working conditions and determine the geometry that is less noisy while maintaining the velocity peak. Among the various possibilities, shortening the final ducts of the nozzle appears to be the most promising solution. These modified nozzles could be easily added to current machines to provide immediate benefits, and this study represents a promising start for action on other machines where this type of device is present.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

This study presents the numerical investigation of bioconvective nanofluid (NF) flow compris-ing gyrotactic microorganisms through convective boundary conditions (CBC) enclosing heat and mass transmission analysis above an inclined extending cylinder. Via appropriate transfor-mation, the set of Partial Differential Equations is transformed into a scheme of nonlinear ODEs. A new set of variables are presented in the directive to get the first-order convectional equations and, then solved numerically by using bvp4c. The influence of several factors on velocity, ener-gy, concentration, and the density of motile microorganisms (DMM) is investigated and exam-ined. The analysis describes and addresses all physical measures of concentration such as Skin Friction (SF), Sherwood number (SN), DMM, and Nusselt number (NN). The present conse-quences display a validation with published. For confirmation of bvp4c, the ND-solve approach is also applied. Error analysis is also examined for the confirmation of the mathematical model.

Knee Osteoarthritis (KOA), the most common knee degenerative disease, involve a slow destructive process, leading to disability and ultimately total knee replacement. The progression of KOA is related to the loss of rheological properties of the synovial fluid (SF), due to slow immunological, inflammatory and enzymatic processes that cleave the hyaluronic acid (HA) and decrease the concentration of specific proteins. Since no effective treatments have been found to halt the progression of KOA, injection of HA-based viscoelastic gels combined with physiotherapy (PT) is an alternative to symptomatic therapies. In order to evaluate the effect of viscosupplementation and PT on the SF characteristics, the SF aspirated from the KOA was spectrophotometrically and rheological analyzed, comparing the receiving groups of HA Kombihylan® and groups that received Kombihylan® and complex PT. In patients treated with PT, SF extracted 6 weeks after viscosupplementation had a superior elastic moduli (G') and viscous moduli (G") profile behavior, having a homogeneous distribution of proteins and polysaccharides in the SF, stimulating stronger interactions. In the absence of PT the G' and G" profiles are non-uniform, suggesting an unorganized supplemented SF with some clustering phenomena, proteins aggregation and a low level of entanglement between HA and macromolecular components in the SF.

Background: The prevalence of human T-lymphotropic virus type-1 (HTLV-1) infection is higher in women, and sexual intercourse has been described as an important route of male-to-female transmission. The present study aimed to quantify HTLV-1 proviral load (PVL) in vaginal fluid, and to investigate correlations with PVL in peripheral blood mononuclear cells (PBMC). Methods: HTLV-1-infected women were consecutively recruited at a multidisciplinary center for HTLV patients in Salvador-Brazil. All women underwent gynecological examinations to obtain cervicovaginal fluid and venipuncture for blood collection. PVL, as measured by real-time quantitative polymerase chain reaction (RT-qPCR), was expressed as the number of copies of HTLV-1/106 cells in blood and vaginal fluid samples. Light microscopy was used to assess cervicovaginal cytopathology and vaginal microbiota. Results: In the 56 included women (43 asymptomatic carriers and 13 diagnosed with HTLV-associated myelopathy/tropical spastic paraparesis-HAM/TSP), mean age was 35.9 (SD±7.2) years. PVL was higher in PBMCs [median: 23,264 copies/106 cells (IQR: 7,420 - 64,371)] than in vaginal fluid [451.9 copies/106 cells (IQR: 0 - 2,672)] (p<0.0001). PVL in PBMCs was observed to correlate directly with PVL in vaginal fluid (R=0.32, p=0.01). PVL was undetectable in vaginal fluid samples from 20 women (35.7%), most of whom were asymptomatic (19/20). Cytopathologic analyses revealed no differences between women with detectable or undetectable PVL. Conclusion: HTLV-1 proviral load is detectable in vaginal fluid and correlates directly with proviral load in peripheral blood. This finding suggests that sexual transmission of HTLV-1 from female to male may occur and vertical transmission, particularly in the context of vaginal delivery.

Fluid mechanics of flow in hydrophobic, rectangular microchannels with finite aspect ratios is of paramount importance. In such microchannels, not only the effect of the side walls should be taken into account, but also the classical assumption of no-slip boundary condition (BC) is no longer valid at the solid-liquid interface. Accordingly, slip flow can occur in microchannels fabricated from surfaces with low wetting conditions, hydrophobic surfaces. Determining the interactions of liquid molecules adjacent to solid surface is still a challenging issue, and it is especially important in small scale domains. Herein, the fluid mechanics of flow through rectangular hydrophobic microchannels has been reconsidered by taking into account the general Navier-slip BCs at the solid-liquid interface. For fully developed incompressible flow in microchannels at low Reynolds number, partial differential equation (PDE) of the momentum equation simplifies to the classical Poisson equation. Accordingly, by analytically solving the Poisson equations with general Navier-slip BCs, the most general forms of velocity distributions, flow rate, friction factor and Poiseuille number have been obtained.

Three-phase interactions (metal-slag-argon) in ladle stirring operations have strong effects on metal-slag mass transfer processes. Specifically, the thickness of the slag controls the fluid turbulence to an extent that once trespassing a critical thickness, increases of stirring strength have not further effects on the flow. To analyze these conditions, a physical model considering the three phases was built to study liquid turbulence in the proximities of the metal-slag interface. A velocity probe placed close to the interface permitted the continuous monitoring and statistical analyses of turbulence. The slag-eye opening was found to be strongly dependent on the stirring conditions, and the mixing times decreased with thin slag thicknesses. Slag entrainment was enhanced with thick slag layers, and high flow rates of the gas phase. A multiphase model was developed to simulate these results finding a good agreement between experimental and numerical results.

The rising of an oil drop in a non-Newtonian viscous solution is studied experimentally. In this case, the shape of the ascending drop is strongly affected by the non-Newtonian properties of the surrounding liquid. We found that the so-called velocity discontinuity phenomena is observed for drops larger than a certain critical size. Beyond the critical velocity, the formation of a long tail is observed, from which small droplets are continuously emitted. We determined that the fragmentation of the tail results mainly from the effect of capillary effects. We explore the idea of using this configuration as a new encapsulation technique, where the size and frequency of droplets can be well predicted.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Abstract Antibacterial activities can be improved using mixed ligands. Mixed ligands involved in this research are sodium sulfadiazine (Na-sfz) and dithiocarbamate (ai-dtc). One-pot synthesis was used to synthesize ligand of aniline dithiocarbamate (ai-dtc) and the corresponding coordination compounds of [VO(sfz)(ai-dtc)] and [Zn(sfz)(ai-dtc)]. Crystals of ai-dtc, which grew from the solution when refrigerated after five days, were diffracted with technique of single crystal x-ray crystallography to reveal the structure. Other characterization techniques involving physicochemical parameters, FT-IR, UV-Vis and NMR (1H NMR and 13C NMR) were carried out on ligands of ai-dtc, sfz and corresponding coordination compounds. Differences in results of FT-IR, UV-Vis and NMR between ligands and their respective metal ions confirmed the coordination. The in vitro antibacterial studies showed that the ligands (not the metal complexes) had modest activity against Gram negative bacteria: Staphylococcus aureus, whereas, the coordination compounds had modest activities against the Gram negative bacteria: Escherichia coli and Pseudomonas aeruginosa.

Alzheimer’s disease (AD) is an irreversible neurodegenerative disease characterized by progressive cognitive decline. The two cardinal neuropathological hallmarks of AD include buildup of cerebral β amyloid (Aβ) plaques and neurofibrillary tangles of hyperphosphorylated tau. The current disease-modifying treatments are still not effective enough to lower the rate of cognitive decline. The paucity of early detection and disease progression biomarkers also seems to present a major obstacle to AD drug development. The current established readouts based on expression levels of amyloid beta, tau and phospho tau have shown many discrepancies in patient samples when linked to disease progression. There is an urgent need to identify diagnostic and disease progression biomarkers from blood, CSF or other biofluids that can facilitate early detection of the disease and provide pharmacodynamic readouts for new drugs being tested in clinical trials. Advances in proteomic approaches using state-of-the-art mass spectrometry, are now being increasingly applied to study AD disease mechanisms, identify drug targets and novel disease biomarkers. In this report, we describe applications of the quantitative proteomic approaches for understanding AD pathophysiology, summarize the current knowledge gained from proteomic investigations of AD and discuss development and validation of new predictive and diagnostic disease biomarkers.

The behavior of convective boundary conditions is studied to delineate their role in heat and mass relegation in the presence of radiation, chemical reaction, and hydromagnetic forces in three-dimensional Powell-Eyring nanofluids. Implications concerning non-Fourier’s heat flux and non-Fick’s mass flux with respect to temperature nanoparticle concentration were examined to discuss the graphical attributes of the principal parameters. An efficient optimal homotopy analysis method is used to solve the transformed partial differential equations. Tables and graphs are physically interpreted for significant parameters

Repeated single-point measurements of thoracic bioimpedance at single (low)-frequency are strongly related to fluid changes during hemodialysis. Extension to semi-continuous measurements may provide longitudinal details in the time pattern of the bioimpedance signal, and multifrequency measurements may add in-depth information on the distribution between intra- and extracellular fluid. This study aims to investigate the feasibility of semi-continuous multifrequency thoracic bioimpedance measurements by a wearable device in hemodialysis patients. Therefore, thoracic bioimpedance was recorded semi-continuously (i.e. every ten minutes) at nine frequencies (8 – 160 kHz) in 68 patients during two consecutive hemodialysis sessions, complemented by a single-point measurement at home in-between both sessions. On average, the resistance signals increased during both hemodialysis sessions and decreased during the interdialytic interval. The increase during dialysis was larger at 8 kHz (∆ 32.6 Ω during session 1 and ∆ 10 Ω during session 2) compared to 160 kHz (∆ 29.5 Ω during session 1 and ∆ 5.1 Ω during session 2). Whereas the resistance at 8 kHz showed a linear time pattern, the evolution of the resistance at 160 kHz was significantly different [p < 0.0001]. Measuring bioimpedance semi-continuously and with a multifrequency current is a major step forward in the understanding of fluid dynamics in hemodialysis patients. This study paves the road towards remote fluid monitoring.

The two-stage direct thermal contact (2sDTC) process is a rapid dewatering approach for fluid fine tailings (FFT) that is integrated into an oil sands bitumen extraction plant to reduce tailings pond storage and freshwater usage. In the first stage, combustion gas directly contacts atomized FFT, vaporizing water and yielding dry solids and steam-rich hot gas. The second stage involves pond effluent water directly contacting the steam-rich hot gas, recovering heat and condensing moisture. Case studies confirm the technical feasibility of the integration. Benefits include producing a dry discharge, reducing tailings water discharge and conserving an equivalent to 0.2 barrels of freshwater per barrel of oil produced. Most importantly, these benefits incur no additional energy cost to the plant as the integration eliminates the energy penalty and CO2 emissions associated with FFT dewatering. Further capacity enhancement can be achieved by using centrifuge-concentrated FFT. The study reveals that FFT concentrated to ~50 wt% solids could still maintain its pump-ability and be accommodated by the 2sDTC process, leading to an integration which could dewater more FFT annually and conserve more freshwater ( 0.58 barrels per barrel of oil produced), with the sole energy requirement being the power to drive the centrifuge machinery.

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

The Physics-Informed Neural Networks (PINNs) improve the efficiency of data utilization by combining physical principles with neural network algorithms and ensure that the predictions are consistent and stable with the physical laws. PINNs opens up a new approach to address inverse problems in fluid mechanics. Based on the single-relaxation-time lattice Boltzmann method (SRT-LBM) with the Bhatnagar-Gross-Krook (BGK) collision operator, the PINN-SRT-LBM model is proposed in this paper for solving the inverse problem in fluid mechanics. The PINN-SRT-LBM model consists of three components. The first component involves a deep neural network that predicts the equilibrium control equations in different discrete velocity directions within SRT-LBM. The second component employs another deep neural network to predict non-equilibrium control equations, enabling inference of the fluid's non-equilibrium characteristics. The third component, a physics informed function translates the outputs of the first two networks into physical infor-mation. By minimizing the residuals of the physical partial differential equations (PDEs), the physics informed function infers relevant macroscopic quantities of the flow. The model evolves two sub-models applicable to different dimensions, named PINN-SRT-LBM-I and PINN-SRT-LBM-II models according to the construction of the physical informed function. The innovation of this work is the introduction of SRT-LBM and discrete velocity models as physical drivers into the neural network through the interpretation function. Therefore, PINN-SRT-LBM allows the neural network to handle inverse problems of various dimensions and focus on problem-specific solving. Experimental results confirm the accurate prediction of flow infor-mation at different Reynolds numbers within the computational domain. Relying on the PINN-SRT-LBM models, inverse problems in fluid mechanics can be solved efficiently.

The gauge field equation for fluid mechanics established in Part 1 is developed into a first-order scattering theory in the simplified case of a two-dimensional incompressible flow over a flat plate. This is used to present a model for the origin of Tollmien-Schlichting (TS) waves based on scattering between fluid particles. As a result, analytical formulae for the maximum amplification factor and the transition point from laminar to turbulent flow in the boundary layer are obtained. The mathematical transformations from the stationary field equations in Part 1 to a scattering theory with time evolution along the flow axis using Wick rotation are elaborated in detail.

The main objective of this study is to demonstrate proof of principle that computational fluid dynamics (CFD) modeling is a tool for studying the contribution of covert and overt vascular architecture to the risk of cerebrovascular disease in in sickle cell disease (SCD) as well as uncover one or more mechanism of response to therapy such as chronic red blood cell (cRBC) transfusion. We analyzed baseline (screening), pre-randomization and study exit magnetic resonance angiogram (MRA) images from 10 (5 each from the transfusion and observation arms) pediatric sickle SCD participants in the silent cerebral infarct transfusion (SIT) trial, using CFD modeling. We reconstructed the intracranial portion of the internal carotid artery and branches and extracted the geometry using 3D Slicer. We cut specific potions of the large intracranial artery to include segments of the internal carotid, middle, anterior, and posterior cerebral artery such that the vessel segment analyzed extended from the intracranial beginning of the internal carotid artery up to immediately after (~0.25 inches) the middle cerebral artery branching point. Cut models were imported into Ansys 2021R2/2022R1 and laminar and time-dependent flow simulation was performed. Change in time averaged mean velocity, wall shear stress, and vessel tortuosity were compared between the observation and cRBC arm. We did not observe a correlation between time averaged mean velocity (TAMV) and mean transcranial doppler (TCD) velocity at study entry. There was also no difference in change in time average mean velocity, wall shear stress (WSS), and vessel tortuosity between the observation and cRBC transfusion arms. WSS and TAMV were abnormal for 2 (developed TIA) out of the 3 participants (one participant had SCI) that developed neurovascular outcomes. CFD approaches allows for the evaluation of vascular topology and hemodynamics in SCD using MRA images. In this proof of principle study, we show that CFD could be a useful tool and we intend to carry out future studies with a larger sample to enable more robust conclusions.