Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

In this paper, a multibody calculation methodology has been applied to the vibration analysis of a 4-cylinder, 4-stroke, turbocharged diesel engine, with a simulation driven study of the angular speed variation of a crankshaft under consideration of different modeling assumptions. Moreover, time dependent simulation results, evaluated at the engine supports, are condensed to a vibration index and compared with experimental results, obtaining satisfactory outcomes. The modal analysis also considers the damping aspects and has been conducted using a multibody model created with the software AVL/EXCITE. The influence of crankshaft torsional frequencies on the rotational speed behavior has been evaluated in order to reduce the vibration phenomena.

Variational mode decomposition (VMD) is a recently introduced adaptive signal decomposition algorithm with a solid theoretical foundation and good noise robustness compared with empirical mode decomposition (EMD). There is a lot of background noise in the vibration signal of diesel engine. To solve the problem, a denoising algorithm based on VMD and Euclidean Distance is proposed. Firstly, a multi-component, non-Gauss, and noisy simulation signal is established, and decomposed into a given number K of band-limited intrinsic mode functions by VMD. Then the Euclidean distance between the probability density function of each mode and that of the simulation signal are calculated. The signal is reconstructed using the relevant modes, which are selected on the basis of noticeable similarities between the probability density function of the simulation signal and that of each mode. Finally, the vibration signals of diesel engine connecting rod bearing faults are analyzed by the proposed method. The results show that compared with other denoising algorithms, the proposed method has better denoising effect, and the fault characteristics of vibration signals of diesel engine connecting rod bearings can be effectively enhanced.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

The railway industry focus in the past years was to research, find and develop methods to mitigate noise and vibration resulted from wheel/rail contact along track infrastructure. This resulted in a wide range of abatement measures that are available for the professionals of the industry today. However, although there are many options in the market, their practical implementations depend upon general constraints that affect most technological application in the engineering world. The progression of these technologies have facilitated the selection of more adequate methods for each best case scenario, but further studies are ought to be made to proper assess if each one is fit for their purpose. Every method implementation must be analyzed through budget and timeframe limitations, which includes building, maintenance and inspection costs and time allocation, while also aiming to meet different benefits, such as environmental impact control and wear of the whole infrastructure. There are several situations and facilities in a railway project design that need noise and vibration mitigation methods and each design allocates different priorities for each one of them. Traditionally the disturbance caused by railways to the community are generated by wheel/rail contact sound radiation that expresses in different ways, depending on the movement of the rolling stock and track alignment, such as rolling noise, impact noise and curve noise. More specifically, in special trackworks such as turnouts, the main area of this study, there are two noises types that must be evaluated: impact noise and screeching noise. With respect to the second, it is similar to curve squeals and, being such, its mitigation methods are to be assigned as if it was to abate curve squeal in turnouts and crossings. The impact noise on the other hand, emerges from the sound made by the rolling stock moving through joints and discontinuities (i.e. gaps) that composes these special components of a railway track. A life cycle analysis is therefore substantial for this reality and in this case will be applied to Squeal and Impact Noise on Special Trackwork. The evaluation is based on a valid literature review and the total costs were assumed by industry reports to maintain coherency. The period for a life cycle analysis is usually of 50 years, hence it was the value assumed. As for the general parameters, an area with high density of people was considered to estimate the values for a community with very strict limits for noise and vibration.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

Not a lot is known about either death or the dying process. Politicians and many in the medical profession in the UK tend to shy away from interfering with it by not allowing euthanasia as an end of life option for the patient. This is the first paper in a series of two, comparing the situation in human medicine and veterinary medicine, in which euthanasia is well practiced for relieving suffering at the end of an animal’s life. This first part takes the form of a literature review including best practice around end of life care, its deficiencies and the need for assisted dying. Veterinary surgeons are well trained in the ethics of euthanasia and put it to good use in the best interest of their animal patients. In countries which have legalized physician assisted suicide for the terminally ill reporting indicates that it works well, without increases in involuntary euthanasia and most importantly without intimidation of the vulnerable. However, there is still an ever increasing tendency to overuse sedation and opioids at the end of life, which merits further investigation. With advances in medical science able to significantly prolong the dying process, patient autonomy demands a review of the law in the UK.

Based on the demographic shift and the related challenges resulting from the growing number of elderly and persons with chronic diseases, the idea of smart home that supports its inhabitants in the daily life, gains importance. The purpose of this paper was to examine in a prototypic Ambient Assisted Living environment if users after interaction with different health-supporting applications intend to use such in the future. Two experimental studies exemplary show possible applications of home-integrated technology that can support, assist and accompany the target group in different contexts, and examine to what extent participants are willing to future use such sophisticated technology at home. The results show that people in general, but especially the old and chronically ill ones are quite fascinated of health-supporting ambient technology and the majority intends to use such ambient assistance in the future (study I). Moreover, serious games for healthcare are shown as a hedonic use of technology in smart homes that have a great potential to retain or improve the physical health, mobility and the overall well-being of the inhabitants (study II). The article provides two examples of ambient technology to leverage the demographic change and presents important user factors for facilitating high user acceptance.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

This study presents an exact solution to the free vibration analysis of a uniform Timoshenko beam, with a harmonic vibration being assumed. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. In this paper, a moment-shear force-circular frequency-curvature relationship was presented. The complete study was based on this relationship and closed-form expressions of efforts and deformations were derived. The free vibration response of single-span systems and spring-mass systems was analyzed; closed-form formulations of matrices expressing the boundary conditions were presented and the natural frequencies were determined by solving the eigenvalue problem. Systems with intermediate mass, spring, or spring-mass system were also analyzed. Furthermore, first-order dynamic stiffness matrices in local coordinates were derived. Finally, a second-order analysis of beams resting on an elastic Winkler foundation was conducted. The results obtained in this paper were in good agreement with those of other studies.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

This is the second of a series of two papers comparing the end of life issues in human and veterinary medicine. We outline the main differences between human and animal patients such as patient communication, finance and ‘conflicts of interest’ between animal, owner and veterinarian. We discuss striking similarities between human and veterinary issues such as assessing quality of life and the primary role of the attending veterinarian or doctor being the welfare and care of the patient. This paper takes the form of an ethical argument in favour of allowing euthanasia in human medicine, by providing insights into end of life issues for humans from an independent veterinary perspective. Veterinary surgeons are well trained in the ethics of euthanasia and put it to good use in the best interest of their animal patients. Doctors in the UK are limited and unwilling to put forward a case for the option of euthanasia for those patients who face a slow and agonizing death. With advances in medical science being able to significantly prolong the dying process, autonomy for the patient demands a review of the law regarding patient choice in the UK.

Infertility affects approximately 15% of couples worldwide, an estimated 30% of which is related to male factor infertility. Application of low level laser therapy (LLLT) to improve fertility status is a rapidly growing discipline in medicine. Laser therapy triggers a variety of biological processes through interaction with primary cellular photoacceptors. The present review aims at evaluating the literature available in the MEDLINE/ PubMed on cellular and molecular mechanisms of photobiomodulation in the domains of reproductive and veterinary medicine. We primarily focused on the clinical application of laser treatment on seminal quality, in particular its role in promoting spermatozoa motility, as well as the role of phototherapy in modulating assisted reproduction (ART). Additionally, we investigated the strength of evidence in support of the positive impact of photobiomodulation on facilitating ART.

This study presents a vibration control using actively tunable vibration absorbers (ATVA) to suppress vibration of a thin plate. The ATVA’s is made of a sandwich hollow structure embedded with the electrorheological fluid (ERF). ERF is considered to be one of the most important smart fluids and it is suitable to be embedded in a smart structure due to its controllable viscosity property. ERF’s apparent viscosity can be controlled in response to the electric field and the change is reversible in 10 microseconds. Therefore, the physical properties of the ERF-embedded smart structure, such as the stiffness and damping coefficients, can be changed in response to the applied electric field. A mathematical model is difficult to be obtained to describe the exact characteristics of the ERF embedded ATVA because of the nonlinearity of ERF’s viscosity. Therefore, a fuzzy modeling and experimental validations of ERF-based ATVA from stationary random vibrations of thin plates are presented in this study. Because Type-2 fuzzy sets generalize Type-1 fuzzy sets so that more modelling uncertainties can be handled, a semi-active vibration controller is proposed based on Type-2 fuzzy sets. To investigate the different performances by using different types of fuzzy controllers, the experimental measurements employing type-1 fuzzy and interval type-2 fuzzy controllers are implemented by the Compact RIO embedded system. The fuzzy modeling framework and solution methods presented in this work can be used for design, performance analysis, and optimization of ATVA from stationary random vibration of thin plates.

There are currently around 78 Nuclear Power Plants (NPP) in the world based on Boiling Water Reactors (BWR). The current parameter to assess BWR instability issues is the linear Decay Ratio (DR). However, it is well known that BWRs are complex non-linear dynamical systems that may even exhibit chaotic dynamics that normally preclude the use of the DR when the BWR is working at a specific operating point during instability. In this work a novel methodology based on an adaptive Shannon Entropy estimator and on Noise Assisted Empirical Mode Decomposition variants is presented. This methodology was developed for real-time implementation of a stability monitor. This methodology was applied to a set of signals stemming from several NPPs reactors (Ringhals-Sweden, Forsmark-Sweden and Laguna Verde-Mexico) under commercial operating conditions, that experienced instabilities events, each one of a different nature

Cannabis is a flowering plant that has long been used for medicinal, therapeutic, and recreational purposes. Cannabis contains more than 500 different compounds, including a unique class of terpeno-phenolic compounds known as cannabinoids; Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD) are the most prevalent cannabinoids and have been associated with the therapeutic and medicinal properties of the cannabis plant. In this paper, continuous flow microwave assisted extraction (MAE) is presented and compared with other methods for commercial cannabis extraction. The practical issues of each extraction method are discussed. The main advantages of MAE are: continuous-flow method which allows for higher volumes of biomass to be processed in less time than existing extraction methods, improved extraction efficiency leading to increased final product yields, improved extract consistency and quality because the process does not require stopping and restarting material flows, and ease of scale-up to industrial scale without the use of pressurised batch vessels. Moreover, due to the flexibility of changing the operation conditions, MAE eliminates additional steps required in most extraction methods, such as biomass decarboxylation, winterisation, which typically adds at least a half day to the extraction process. Another factor that sets MAE apart is the ability to achieve high extraction efficiency even at the industrial scale. Whereas the typical recovery of active compounds using supercritical CO¬2 remains around 70-80%, via MAE up to 95% of the active compounds from cannabis biomass can be recovered at the industrial scale.

This study analyzes the modeling and dynamics of a novel passive in Multi-Degree-of-Freedom (MDOF) vibration isolation platform which can achieve significant isolation effect. Symmetrical Scissor-Like structures (SLSs) are utilized in the proposed MDOF isolation platform as the supporting and isolation elastic components. Based on the mathematical modeling and theoretical analysis of the MDOF vibration isolation system with SLSs, the effect of structural parameter and joint friction on stiffness and damping properties is investigated. It is shown that due to geometric relations within the SLSs, the natural frequencies can be reduced via adjusting structural parameters of the SLS for different direction vibration isolation. Theoretical and experimental results show that the SLS isolation platform can achieve much better loading capacity and vibration isolation performance simultaneously by only using linear passive components because of the MDOF adjustable stiffness property. Therefore, with low costing and energy consumption, the proposed novel isolation platform can provide the improvement of vibration suppression in various engineering practices.

This paper addresses the analysis for the nonlinear vibration response of a rectangular tube with a flexible end and non-rigid acoustic boundaries. This is a further work of the linear structural acoustic problem in a well-known acoustic book. In fact, the acoustic boundaries of an enclosed space sometimes are non-rigid and the structural vibration responses are nonlinear. These two points are the focuses of this paper. The multi-level residue harmonic balance method is applied to this nonlinear structural acoustic problem. The results obtained from the multi-level residue harmonic balance method and numerical method are generally in good agreement. The effects of excitation magnitude, tube length, and phase shift parameter etc. are examined.

This paper presents an approach to the Kirchhoff-Love plate theory (KLPT) using the finite difference method (FDM). The KLPT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally in the case of KLPT, the finite difference approximations are derived based on the fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection surface. The FOPH is made for the fourth and third derivative of the deflection surface while the SOPH is made for its second and first derivative; this leads to a 13-point stencil for the governing equation. In addition, the boundary conditions and not the governing equations are applied at the plate edges. In this paper, the FOPH was made for all of the derivatives of the deflection surface; this led to a 25-point stencil for the governing equation. Furthermore, additional nodes were introduced at plate edges and at positions of discontinuity (continuous supports/hinges, incorporated beams, stiffeners, brutal change of stiffness, etc.), the number of additional nodes corresponding to the number of boundary conditions at the node of interest. The introduction of additional nodes allowed us to apply the governing equations at the plate edges and to satisfy the boundary and continuity conditions. First-order analysis, second-order analysis, buckling analysis, and vibration analysis of plates were conducted with this model. Moreover, plates of varying thickness and plates with stiffeners were analyzed. Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. In first-order, second-order, buckling, and vibration analyses of rectangular plates, the results obtained in this paper were in good agreement with those of well-established methods, and the accuracy was increased through a grid refinement.

Electric field assisted combustion is an important means to improve fuel combustion efficiency. This paper conducts extensive research on flame characteristics under different forms and different application methods of electric fields, emission of soot particles and simulation status. Different flame parameter measurement methods will lead to different degrees of error, and perfect numerical simulation can make simple predictions on experimental data. Most of the current numerical simulations are in two dimensions, and it is necessary to develop a complete and accurate three-dimensional model to simulate and predict the characteristics of the flame under an electric field. The emission of soot particles is also affected by the electric field, and reasonable electric field parameters can greatly reduce the emission of soot particles. It is recommended to conduct centralized measurement of different fuels under the electric field under high pressure and temperature conditions, so as to be able to develop a wider and more accurate flame dynamics and chemical model under the electric field.

Due to the increasing importance of mangroves in climate change mitigation projects, more accurate and cost-effective aboveground biomass (AGB) monitoring methods are required. However, field measurement of AGB may be a challenge because of its remote location and the difficulty to walk in these areas. This study is based on the Livelihoods Fund’ Oceanium project of 10,000 hectare mangrove plantations monitoring. In a first step, the possibility of replacing traditional field measurements of sample plots in a young mangrove plantation by a semiautomatic processing of UAV-based photogrammetric point clouds was assessed. In a second step, Sentinel-1 radar and Sentinel-2 optical imagery were used as auxiliary information to estimate AGB and its variance for the entire study area under a model-assisted framework. AGB was measured using UAV imagery in a total of 95 sample plots. UAV plot data was used in combination with non-parametric Support Vector Regression (SVR) models for the estimation of the study area AGB using model-assisted estimators. Purely UAV-based AGB estimates and their associated standard error (SE) were compared with model-assisted estimates using (1) Sentinel-1, (2) Sentinel-2 and (3) a combination of Sentinel-1 and Sentinel-2 data as auxiliary information. The validation of the UAV-based individual tree height and crown diameter measurements showed a root mean square error (RMSE) of 0.21 m and 0.32 m respectively. Relative efficiency of the three model-assisted scenarios ranged between 1.61 and 2.15. Although all SVR models improved the efficiency of the monitoring over UAV-based estimates, the best results were achieved when a combination of Sentinel-1 and Sentinel-2 data was used. Results indicated that the methodology used in this research can provide accurate and cost-effective estimates of AGB in mangrove young plantations.

The ectoparasitic mite Varroa destructor is the most significant pathological threat to the western honey bee, Apis mellifera, leading to the death of most colonies if left untreated. An alternative approach to chemical treatments is to selectively enhance heritable honey bee traits of resistance or tolerance to the mite through breeding programs, or select for naturally surviving untreated colonies. We conducted a literature review of all studies documenting traits of A. mellifera populations either selectively bred or naturally selected for resistance and tolerance to mite parasitism. This allowed us to conduct an analysis of the diversity, distribution and importance of the traits in different honey bee populations that can survive V. destructor throughout the globe. In a second analysis, we investigated the genetic bases of these different phenotypes by comparing ’omics studies (genomics, transcriptomics, and proteomics) of A. mellifera resistance and tolerance to the parasite. Altogether, this review provides a detailed overview of the current state of the research projects and breeding efforts against the most devastating parasite of A. mellifera. By highlighting the most promising traits of varroa-surviving bees and our current knowledge on their genetic bases, this work will help direct future research efforts and selection programs to control this pest. Additionally, by comparing the diverse populations of honey bees that exhibit the traits, this review highlights the consequences of anthropogenic and natural selection on the interactions between hosts and parasites.

The excessive vibration caused by crowds walking across footbridges has attracted great public concerns in the past few decades. This paper presents, from considering the dynamic characteristics of the bipedal crowd model, a new stability limit criterion based on the bipedal excitation model. The stability limit can be used to estimate the upper boundary of crowd size. In addition, the dynamic stable performances of a structure, under a certain walking crowd size, can be predicted by the stability criterion. This proposed mechanism provides an alternative comprehension how crowd excite the excessive sway motion with a large-span structure.

The research paper presents a new approach towards constructing motion equations for structures with attached MTMDs (multiple tuned mass dampers). A primary system, with MDOF (multiple dynamic degrees of freedom) was reduced to an equivalent system with a SDOF (single degree of freedom) through the modal approach, and equations from additional MTMDs were added to a thus-created system. Optimization based on H2 and H∞ for the transfer function associated with the generalized displacement of an SDOF system. The research work utilized GA (genetic algorithms) and SA (simulated annealing method) optimization algorithms to determine the stiffness and damping parameters for individual TMDs. The effect of damping and stiffness (MTMD tuning) distribution depending on the number of TMDs was also analyzed. The paper also reviews the impact of primary system mass change on the efficiency of optimized MTMDs, as well as confirms the results of other authors involving greater MTMD effectiveness relative to a single TMD.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

Complex blade responses such as a rotating stall or simultaneous resonances are common in modern engines and their observation can be a challenge even for state-of-the-art tip-timing systems and trained operators. This paper analyses forced vibrations of axial compressor blades, measured during the bench tests of the SO-3 turbojet. In relation to earlier studies conducted in ITWL with a small number of sensors, a multichannel tip-timing system let us observe simultaneous responses or higher-order modes. To find possible symptoms of a failure, blade responses in a healthy and unhealthy engine configuration with an inlet blocker were studied. The used analysis methods covered all-blade spectrum and the circumferential fitting of blade deflections to the harmonic oscillator model. The proposed modal solver can track the vibration frequency and adjust the engine order on the fly. That way, synchronous and asynchronous vibrations are observed and analysed together with an extended variant of least squares. The proposed approach helps to avoid common mistakes and saves a lot of work related to configuring the conventional solver.

Sustainable agricultural production is endangered by several ecological factors such as drought, extreme temperatures, excessive salts, parasitic ailments, and insect pest infestation. These challenging environmental factors may have adverse effects on future agriculture production in many countries. In modern agriculture, conventional crop breeding techniques alone are inadequate for achieving the increasing population’s food demand on a sustainable basis. The advancement of molecular genetics and related technologies are promising tools for the selection of new crop species. Gene pyramiding through marker assisted selection (MAS) and other techniques have accelerated the development of durable resistant/tolerant lines with high accuracy in the shortest possible period of time for agricultural sustainability. Gene stacking has not been fully utilized for biotic stress resistance development and quality improvement in most of the major cultivated crops. This review emphasizes on gene pyramiding techniques that are being successfully deployed in modern agriculture for improving crop tolerance to abiotic and biotic stresses for sustainable crop improvement.

Optical and mechanical properties of multilayer coatings depend on the selected layer materials and the deposition technology; therefore, knowledge of the performances of thin films is essential. In the present work, titanium dioxide (TiO2) and silicon dioxide (SiO2) thin films have been prepared by plasma ion-assisted deposition (PIAD). The optical, structural, and mechanical properties of thin films have been investigated using spectrometer/ellipsometer, X-ray diffraction (XRD), atomic force microscopy (AFM), and laser interferometer. The results show that TiO2 film fabricated by PIAD induces a high refractive index, wide optical band gap, amorphous structure, smooth surface, and tensile stress. In the case of SiO2 film, high bias voltage leads to dense structure and compressive stress. As an application, a three-wavelength high reflectance at 632.8, 808, and 1550nm is optimized and deposited. The dependence of total stress in the multilayer on the substrate temperature is studied as well. In conclusion, it is demonstrated that PIAD is an effective method for the preparation of ultralow stress TiO2/SiO2 multilayer films. The achieved stress is as low as 1.4Mpa. The result could provide guidance to the stress optimization of most optical components without prefiguring, backside coating, and post-deposition treatments.

This paper first discusses a fractional-order Liu system of order as low as 2.7 and shows its chaotic characteristics by carrying out numerical simulations such as Lyapunov exponents, bifurcation diagrams and phase portraits. Then, by using the topological horseshoe theory and computer-assisted proof, the existence of chaos in the system is verified theoretically. Finally, the fractional-order system is implemented on a Field Programmable Gate Array (FPGA) and the results obtained show that the fractional-order Liu system is indeed chaotic.

The chemical graph theory is a subfield of mathematical chemistry which applies classic graph theory to chemical entities and phenomena. Chemical graphs are main data structures to represent chemical structures in cheminformatics. Computable properties of graphs lay the foundation for (quantitative) structure activity and structure property predictions - a core discipline of cheminformatics. It has a historic relevance for natural sciences, such as chemistry, biochemistry and biology, and is in the heart of modern disciplines, such as cheminformatics and bioinformatics. This review first covers the history of chemical graph theory, then provides an overview of its various techniques and applications for CASE, and finally summarises modern tools using chemical graph theory for CASE.

Vibration measurement serves as the basis for various engineering practices such as natural frequency or resonant frequency estimation. As image acquisition devices become cheaper and faster, vibration measurement and frequency estimation through image sequence analysis continue to receive increasing attention. In the conventional photogrammetry and optical methods of frequency measurement, vibration signals are first extracted before implementing the vibration frequency analysis algorithm. In this work, we demonstrated that frequency prediction can be achieved using a single feed-forward convolutional neural network. The proposed method is verified using a vibration signal generator and excitation system, and the result obtained was compared with that of an industrial contact vibrometer in a real application. Our experimental results demonstrate that the proposed method can achieve acceptable prediction accuracy even in unfavorable field conditions.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

This paper presents a system developed for the assistance with a collaborative robot in hand-assisted laparoscopic surgery (HALS). The system includes a sensing glove with piezoresistive sensors which capture continuously the flexion degree of the surgeon's fingers. These data are analyzed using an algorithm that detects and recognize the selected movements. This information is sent as commands to the collaborative robot throughout the surgical operation. The bending patterns, speed and execution times of the movements are modelled in a pre-phase in which it will extract all the necessary information for later detection during the motion execution. The results obtained with 10 different volunteers show a high degree of accuracy and a low false discovery rate.

This paper studied the nonlinear vibrations of top tensioned cantilevered pipes conveying pressurized steady two-phase flow under thermal loading. The coupled axial and transverse governing partial differential equations of motion of the system were derived based on Hamilton’s mechanics with the centreline assumed to be extensible. Multiple scale perturbation method was used to resolve the governing equations, which resulted to an analytical approach for assessing the natural frequency, mode shape and the nonlinear coupled axial and transverse steady state response of the pipe. The analytical assessment reveals that at some frequencies the system is uncoupled, while at some frequencies a 1:2 coupling exists between the axial and the transverse frequencies of the pipe. Nonlinear frequencies versus the amplitude displacement of the cantilever pipe conveying two-phase flow at super critical mixture velocity for the uncoupled scenario exhibit a nonlinear hardening behaviour, an increment in the void fractions of the two-phase flow resulted to a reduction in the pipe’s transverse vibration frequencies and the coupled amplitude of the system. However, increasing the temperature difference, pressure and the presence of top tension were observed to increase the pipe’s transverse vibration frequencies without a significant change in the coupled amplitude of the system.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

The persistent issue of bacterial and fungal colonization of artificial implantable materials and decreasing efficacy of conventional systemic antibiotics used to treat implant-associated infections has led to the development of a wide range of antifouling and antibacterial strategies. This article reviews one such strategy where inherently biologically active renewable resources, i.e. secondary plant metabolites (SPMs) and their naturally occurring combinations (i.e. essential oils) are used for surface functionalization and synthesis of polymer thin films. With a distinct mode of antibacterial activity, broad spectrum of action and diversity of available chemistries, secondary plant metabolites present an attractive alternative to conventional antibiotics. However, their conversion from liquid to solid phase without significant loss of activity is not trivial. Using select examples, this article shows how plasma techniques provide a sufficiently flexible and chemically reactive environment to enable the synthesis of biologically-active polymer-coatings from volatile renewable resources.

Alfalfa (Medicago sativa L.) is a perennial, outcrossing legume crop predominantly grown for hay, silage, or pasture. Intensive selection has resulted in dramatic improvement in fitness traits, including winter survival and disease resistance. However, there has been minimal improvement in other economically important traits, such as hay yield, which is still comparable to 30 years ago. Intensive phenotyping costs on this type of trait hinder high selection pressure to identify superior outcross individuals. Severe inbreeding depression inhibits the development of inbred lines with accumulated favorable alleles that exhibit heterosis. This review highlights the outcomes of inbreeding depression as well as the causes, including unmasking deleterious alleles and triggering self-incompatibility. We tracked the research efforts that unveil the genetic bases underlying deleterious alleles and self-incompatibility. The magnitudes of inbreeding depression were compared with the rate of heterozygous halved time in diploid and tetraploid organisms. To fill in the gaps between the controversy and existing hypotheses, we theorized a dosage dominant model of inheritance. The dosage dominant model is similar to the Mendelian dominance model, in which a genotype exhibits a dominant phenotype if there is a dominant allele (alphabet dominant). The difference is that in the dosage dominant model, a genotype will result in a dominant phenotype if the number of dominant alleles is equal to or greater than the number of recessive alleles. This review also includes a discussion on the development of pseudo inbreds and a hypothesis to identify deleterious alleles using bulked segregant analysis and consequently to purge deleterious alleles using marker-assisted selection, to progress toward the successful development of pure inbred lines in alfalfa.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

MAPLE (matrix assisted pulsed laser evaporation) depositions of Candida Rugosa lipase were carried out from ice matrices whose composition is optimized in order to minimize conformational damage of the protein, which strongly influences its catalytic activity. To induce lid opening and to protect lipase during the MAPLE process, pentane and m-DOPA amino acid were added to the liquid matrix giving a target formed by a frozen water-lipase-pentane microemulsion. FTIR and AFM were used to investigate the structure of MAPLE deposited lipase films. The ability of MAPLE films to promote transesterification was determined by thin layer chromatography. It was shown that m-DOPA has influence on the aggregation but not on the unfolding of lipase induced by MAPLE, while the microemulsion formed by the addition of pentane to the target composition is effective in protecting lipase during the MAPLE process. MAPLE deposited lipases showed a modified specificity.

The phonon modes in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems have been systematically studied by Raman spectroscopy. The new phonon modes of 104 cm^-1, 94 cm^-1, and 89 cm^-1 were found in all these samples. A crude estimate about the wavenumber of the collective vibration of the stable CuO2 plane was given in this paper. The standard deviations of the new phonons in YBa₂Cu₃O_7-δ and YBa_2-xLa_xCu₃O_7-δ systems were discussed. The results of the calculation indicated that the 104 cm^-1 mode probably stands the c-direction collective vibration of the stable CuO2 plane, the 94 cm^-1 mode stands the a-direction vibration, and the 89 cm^-1 mode stands b-direction vibration. The relevance between these phonons and the superconductivity was discussed. It is found that, as the T_c decreased, the 104 cm^-1 mode and the 94 cm^-1 mode softened, and the 89 cm^-1 mode hardened slightly.

Satellites are subject to various severe vibration during different phases of flight. The concept of satellite smart adapter is proposed in this study to achieve active vibration control of launch vehicle on satellite. The satellite smart adapter has 18 active struts in which the middle section of each strut is made of piezoelectric stack actuator. Comprehensive conceptual design of the satellite smart adapter is presented to indicate the design parameters, requirements and philosophy applied which are based on the reliability and durability criterions to ensure successful functionality of the proposed system. The coupled electromechanical virtual work equation for the piezoelectric stack actuator in each active strut is drived by applying D'Alembert's principle. Modal analysis is performed to characterize the inherent properties of the smart adapter and extraction of a mathematical model of the system. Active vibration control analysis was conducted using fuzzy logic control with triangular membership functions and acceleration feedback. The control results conclude that the proposed satellite smart adapter configuration which benefits from piezoelectric stack actuator as elements of its 18 active struts has high strength and shows excellent robustness and effectiveness in vibration suppression of launch vehicle on satellite.

Recent digital transformations have significantly impacted the current society, economy, and culture. This includes adoption of rapidly emerging technologies, such as artificial intelligence (AI), immersive technology (e.g., virtual, augmented, mixed and extended reality (VR/AR/MR/XR)), cloud services, and internet of things, in our day-to-day life. `Metaverse’ has emerged as a technology that incorporates many of these transforming technologies to deliver personalised immersive experience related to specific application areas. A potential major beneficiary of Metaverse is the educational ecosystem, where highly immersive learning experiences can be delivered to students, catering to their personal learning needs and train them on life skills such as empathy, ethical qualities, and communication skills. The present-day Metaverse allows physical engagement, enabling users to utilise limb movements to interact with the presented materials. However, ethical concerns and technical limitations impede the widespread implementation of the Metaverse in the real-world. This paper provides a comprehensive survey of the existing literature covering the architecture, type and components of Metaverse, followed by practical aspects of metaverse implementation. The paper is concluded by discussing on the open challenges and issues along with their mitigation strategies and future research directions after the detailed usecase of Metaverse in Education.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Free vibration analysis of the porous functionally graded circular plates has been presented on the basis of classical plate theory. The three defined coupled equations of motion of the porous functionally graded circular/annular plate were decoupled to one differential equation of free transverse vibrations of plate. The one universal general solution was obtained as linear combination of the multiparametric special functions for the functionally graded circular and annular plates with even and uneven porosity distributions. The multiparametric frequency equations of functionally graded porous circular plate with diverse boundary conditions were obtained in the exact closed-form. The influences of the even and uneven distributions of porosity, power-law index, diverse boundary conditions and the negligibled effect of the coupling in-plane and transverse displacements on the dimensionless frequencies of the circular plate were comprehensively studied for the first time. The formulated boundary value problem, the exact method of solution and the numerical results for the perfect and imperfect functionally graded circular plates have not yet been reported.

Excessive vibration of temporary grandstand owing to crowd has lateral rhythmic motions can cause human in panic, which attracted increasing attention in recent years. This paper focuses on experiments that a temporary grandstand occupied 20 participants is oscillated by a shaking table with a series of random waves and induced by crowd with rhythmic swaying motions at lateral direction, respectively. And then a series of vibration perception questionnaires about crowd reaction are obtained. Evaluation of annoying level derives in concept of degree of membership and annoying rate method is proposed, then the human health risk of vibration serviceability of temporary grandstand is assessed with acceleration vibration dose value(VDV). From these results it is clear that standing crowd is more tolerant to vibration than seated crowd. The measured vibrations generated by crowd activities on temporary grandstand can cause panic in crowd. New relationship between the annoyance rate and structural acceleration VDV at logarithmic coordinate is proposed. The findings of this study can be utilized to manage the vibration of temporary grandstand and assess the human health risk.

Background and Objectives: Acute compartment syndrome (ACS) is an emergency condition of the lower limb in which prophylactic fasciotomy is required to prevent complications. A negative pressure wound therapy (NPWT) used to the treatment of fasciotomy wounds provide beneficial clinical results. This study aimed to exchange the authors’ experience of using the NPWT installation system on the lower limb wounds after fasciotomy in ACS. Materials and Methods: This is a retrospective study enrolled consecutive patients with ACS, who underwent fasciotomy and was treated with the NPWT installation system at Department of Vascular Surgery, Provincial Hospital in Kielce from April 2016 to July 2017. Results: The study enrolled 15 patients with a diagnosis of ACS (87% men, mean age 65 years old). An open four-compartment fasciotomy (87%) or two-compartment fasciotomy (13%) was performed. The NPWT was applied on the first day after fasciotomy in 87% of patients. Therapy was initiated by the negative pressure of 125 mm Hg, which maintained at this level until the therapy was finalized. In 80% of patients, the vacuum-assisted wound closure (VAC) dressing changes were performed every 3 days. The first approximation of fasciotomy wounds margins occurred on the 4th day after surgery among 67% of individuals. The average time of using VAC on fasciotomy wounds was 9 days. The average time to definitive closure edges of fasciotomy wounds was 12 days. The average time of hospital stay was 17 days. Conclusions: Our experience indicates the legitimacy of using NPWT in wound treatment after fasciotomy in ACS. The NPWT enables faster primary closure of wounds, reduces edema, as well as decreases hospitalization time.

The crack in the blade is the most common type of fatigue damage for Francis turbines. However, the crack sometimes is difficult to be detected in time using the current monitoring system even when the crack is very large. To better monitor the crack, it is imperative to research the effect of a crack on the dynamic behavior of a Francis turbine. In this paper, the dynamic behavior of a Francis turbine runner model with a crack was researched numerically. The intact numerical model was first validated by the experimental data available. Then, a crack was created at the intersection line between one blade and the crown. The change in dynamic behavior with increasing crack length was investigated. Crack-induced vibration localization theory was used to explain the dynamic behavior changes due to the crack. Modal analysis showed that the adopted theory could basically explain the modal behavior change due to the crack. The FFT results of the modal shapes and the localization factors (LF) were used to explain the forced response changes due to the crack. Based on the above analysis, the challenge of crack monitoring was analyzed. This research can also provide some references for more advanced monitoring technologies.

Due to limitation of natural sand from rivers and seas, artificial sand production from large stones or rocks is being increased. However, this sand manufacturing process is dangerous and causes several social problems such as high level of unwanted vibrations or noises. This study investigates vibration characteristics of sand and screen units in artificial sand production plant whose actuating operation is multiple with several different exciting frequencies. As a first step, vibration levels are measured at the sand and screen unit positions using accelerometers in time and frequency domains. The measurement is carried out at two different conditions: activating sand unit only and operating entire facilities such as stone crusher. Vibration signals acquired from several locations of the sand and screen units of the plant are collected and analyzed from waveforms and spectrums of the signals. It is identified that the vibration acceleration level of the screen unit is higher than that of the sand unit. In addition, it is found from the acceleration signals measured at plant office and shipping control center those places are far away from the plant location that the beating phenomenon is occurred by close driving frequencies for several sand units. In this work, the vibration caused from the beating is significantly reduced by adjusting the driving frequencies for the sand units so that they are sufficiently scattered to avoid the beating.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

Estimating the remaining useful life (RUL) of components is a crucial task to enhance the reliability, safety, productivity, and to reduce maintenance cost. In general, predicting the RUL of a component includes constructing a health indicator ( ) to infer the current condition of the component, and modelling the degradation process, to estimate the future behavior. Although many signal processing and data-driven based methods were proposed to construct the , most of the existing methods are based on manual feature extraction techniques, and need the prior knowledge of experts, or rely on a large amount of failure data. Therefore, in this study, a new data-driven method based on the convolutional autoencoder (CAE) is presented to construct the . For this purpose, the continuous wavelet transform (CWT) technique is used to convert the raw acquired vibrational signals into a two-dimensional image; then, the CAE model is trained by the healthy operation dataset. Finally, the Mahalanobis Distance (MD) between the healthy and failure stages is measured as the . The proposed method is tested on a benchmark bearing dataset and compared with several other traditional construction models. Experimental results indicate that the constructed exhibits a monotonically increasing degradation trend and has a good performance to detect incipient faults.

Aim: To develop an index for quantitative assessment of the upper limb motor function in children with cerebral palsy before and after robot-assisted therapy. Method: An upper limb motor function index was developed using kinematic, surface electromyography and three-axis inertial measurements unit data collected from 15 children with cerebral palsy (CP) and 15 typically developed children. Children with CP underwent 18 robot-assisted therapy sessions with the REAplan device. All children were evaluated, using kinematic data from the REAplan, electromyography and three-axis inertial measurements unit readings from its accelerometer. A principal component analysis was conducted to produce an evaluation index, which is able to detect the deviation from the upper limb motor function of typically developing children group. Children with CP were evaluated twice before and after the intervention with Box and Blocks test and Finger-To-Nose test. The discriminative and concurrent validity of the upper limb motor function index were investigated. Results: The upper limb motor function index was higher in children with CP post therapy (p<0.001). Finger-To-Nose test values improved after robot-assisted therapy (p<0.03). A weak but positive correlation was observed between upper limb motor function index and clinical tests (r=0.012, p=0.95 and r=0.13, p= 0.54 for Box and Blocks test and Finger-To-Nose test respectively). Interpretation: The upper limb motor function index successfully differentiated between the typically developing children and children with CP and was effective in assessing the improvement of the upper limb motor function after robot-assisted therapy. The upper limb motor function index could be extended to assess and monitor rehabilitation therapies of other populations, such as those with stroke and Parkinson’s disease.

Rice (Oryza sativa L.) supplies nourishment to about half of the population of the world's inhabitants. Of them, more than 2 billion people suffer from "hidden hunger" in which they are unable to meet the recommended nutrients or micronutrients from their daily dietary intake. Bio-fortification refers to developing micronutrient-rich diet foods using traditional breeding methods and modern biotechnology, a promising approach to nutrition enrichment as part of an integrated strategy for food systems. To improve the profile of rice grain for the biofortification related traits, understanding the genetics of important biofortification traits is required. Moreover, these attributes are quantitative in nature and are influenced by several genes and environmental variables. In the course of past decades, several endeavours such, as finding the important quantitative trait loci (QTLs) for improving the nutrient profile of rice seeds were successfully undertaken. In this review, we have presented the information regarding the QTLs identified for the biofortification traits in the rice.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

As an emerging building solution, cross-laminated timber (CLT) floors have been increasingly used in mass timber construction. The current vibration design of CLT floors is conservative due to the assumption of simple support conditions in the floor-to-wall connections. It is noted that end fixity occurs as a result of clamping action at the ends, arising from the gravity load applied by the structure above the floor and by the mechanical fasteners. In this paper, the semi-rigid floor-to-wall connections are treated as elastically restrained edges against rotations to account for the effect of partial constraint. A rotational end-fixity factor was first defined to reflect the relative bending stiffness between CLT floors and elastic restraints at the edges. Then, for the design of vibration serviceability of CLT floors as per the Canadian Standard for Engineering Design in Wood (CSA O86), restraint coefficients were defined and their analytical expressions were derived for natural frequencies and the mid-span deflection under a concentrated load, respectively. In particular, a simplified formula of the restraint coefficient for the fundamental frequency was developed to assist engineers in practical design. At last, by comparing with reported experimental data, the proposed design formula showed excellent agreement with test results. In the end, the proposed end fixity factor with their corresponding restraint coefficients is recommended as an effective mechanics-based approach to account for the effect of end support conditions of CLT floors.

The preparation of new materials based on starch for the development of biodegradable packaging is increasing, however, the poor properties of this biopolymer for this application causes an area of opportunities for the improvement of water vapour permeability (WVP), mechanical properties, thermal properties, hydrophilicity, water absorption, among others. Hence, starch has been combined with other polymers such as polyvinyl alcohol, which has shown an improvement in the mechanical properties of starch, also, the use of clays suggests that the properties of response to water can be improved. Therefore, in this work, the preparation and characterization of starch-PVA-nanoclay films prepared by solvent casting is reported. The results obtained suggest that the sonication of nanoclay is necessary to reach a good dispersion, which promotes a strong interaction among starch-PVA-nanoclay. In addition, the properties of WVP and mechanical properties of films improved with incorporation of nanoclay, the concentration of 0.5% w/v of nanoclay showed to be the best concentration due to concentrations of 1.0 and 1.5% w/v were poorer than 0.5% w/v. Accordingly, the successful incorporation of nanoclays into the matrix starch-PVA suggests that this material is a good candidate for use as packaging.

UAV cooperative control has been an important issue in UAV-assisted sensor network, thanks to the considerable benefit obtained from cooperative mechanism of UAVs being applied as a flying base station. In coverage scenario, the tradeoff between coverage performance and transmission performance often makes deployment of UAVs fall into a dilemma, since both indexes are related to the distance between UAVs. To address this issue, UAV coverage and data transmission mechanism is analyzed in this paper, then an efficient multi-UAV cooperative deployment model is proposed. The problem is also modeled as a coalition formation game (CFG). The CFG with Pareto order is proved to have a stable partition. Then, an effective approach consisting of coverage deployment and coalition selection is designed, wherein UAVs can decide strategies cooperatively to achieve better coverage performance. Combining analysis of game approach, a coalition selection and position deployment algorithm based on Pareto order (CSPDA-PO) is designed to execute coverage deployment and coalition selection. Finally, simulation results are shown to validate the proposed approach based on efficient multi-UAV cooperative deployment model.

Conventional phenotyping breeding approaches for vegetable crops like Solanaceae, Bulb, Root crops, have made a significant contribution by developing many varieties. Despite this, conventional phenotyping approaches are not sufficient due to the longer time taken to develop a variety, low genetic gain, environmental factors and some other externalities that affect the phenotype-based selection. To address the challenges of conventional phenotype, a new recent method of high throughput phenotyping (HTP) is considered a promising tool. The development of high-throughput phenotyping technology began in the preceding decade as advancements in sensor, computer vision, automation, and advanced machine learning technologies. HTP platforms are being utilized to undertake non-destructive assessments of the complete plant system in a range of crops. HTP provides the precise measurements and suggests the collection of high-quality and accurate data which is necessary for standardizing phenotyping for the collection of genetic dissection and genomic assisted breeding such as genome-wide association studies (GWAS), linkage mapping, marker-assisted selection (MAS), genomic selection (GS). The remainder of this chapter discusses how high-throughput phenotyping technologies can be used in genomic-assisted breeding for vegetable crops

We demonstrate hybrid integration of a lithium niobate microring resonator with a silicon nitride waveguide in the vertical configuration to achieve efficient light coupling. The microring resonator is fabricated on a lithium niobate on insulator (LNOI) substrate using photolithography assisted chemo-mechanical etching (PLACE). A fused silica cladding layer is deposited on the LNOI ring resonator. The silicon nitride waveguide is further produced on the fused silica cladding layer by first fabricating a trench in the fused silica using focused ion beam (FIB) etching for facilitating the evanescent coupling, followed by formation of the silicon nitride waveguide on the bottom of the trench. The FIB etching ensures the required high positioning accuracy between the waveguide and the ring resonator. We achieve Q-factors as high as 1.4*10^7 with the vertically integrated device.

The prevalence of obesity or metabolic syndrome is increasing worldwide (“Globally metabodemic”). Approximately 25% of adult general population is suffering from nonalcoholic fatty liver disease (NAFLD) which has become serious health problem. Hepatic fibrosis is the most significant determinant of all cause and liver -related mortality in NAFLD. Noninvasive test (NIT) should be urgently required to evaluate hepatic fibrosis in NAFLD. Fibrosis-4 (FIB-4) index is the 1st triaging tool for excluding advanced fibrosis because of its accuracy, simplicity, and cheapness especially for general physicians or endocrinologists, although FIB-4 index has several drawbacks. Accumulating evidence has suggested that vibration controlled transient elastography (VCTE) and the enhanced liver fibrosis (ELF) test may become useful as the 2nd step after triaging by FIB-4 index. The leading cause of mortality in NAFLD is cardiovascular disease (CVD), extrahepatic malignancy, and liver-related diseases. NAFLD often complicates chronic kidney disease (CKD), resulting in increased simultaneous liver kidney transplantation (SLKT). FIB-4 index could be a predictor of not only liver-related mortality and incident hepatocullar carcinoma (HCC) but also prevalent and incident CKD, CVD, and extrahepatic malignancy. Although NITs as milestones for evaluating treatment efficacy have never been established, FIB- 4 index is expected to reflect histological hepatic fibrosis after treatment in several longitudinal studies. We here review the role of FIB-4 index as 1st step NIT in management of NAFLD.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

: The effect that the microstructure exerts on the TRIP phenomenon and on the mechanical properties in a multiphase steel was studied. Samples of an initially cold-rolled ferrite-pearlite steel underwent different intercritical annealing treatments at 750 °C until an equal fractions of austenite/ferrite was reached; the intercritical treatment was followed by isothermal bainitic treatments before cooling the samples to room temperature. Samples in the first treatment were heated directly to the intercritical temperature, whereas other samples were heated to either 900 or 1100 °C to obtain a fully homogenized, single phase austenitic microstructure prior to the conducting the intercritical treatment. The high temperature homogenization of austenite resulted in the decrease in its stability, so a considerable austenite fraction transformed into martensite by cooling to room temperature after the bainitic heat treatment. Most of the retained austenite transformed during the tensile tests, and as a consequence, the previously homogenized steels showed the highest UTS. In turn, the steel with a ferritic-pearlitic initial microstructure, exhibited higher ductility than the other steels and texture components that favor forming processes.

This paper questions the potential shift of reproduction towards assisted reproductive technologies due to benefits provided by genetic manipulation of embryos. In order to examine the viability of such a shift and its implications from a regulatory perspective, we relied on two panels of experts from Israel and Spain, using the Delphi method and a series of in-depth interviews. We anticipate, at a first stage, a continuous-steady growth in the use of IVF, supplemented by preimplantation genetic diagnosis and the introduction of CRISPR/Cas. At a second stage, attracting a growing share of fertile people would require developments in genomics. While it is unclear whether these developments will fully materialize, they could be replaced by technoscientific imaginaries generating perceived benefits. We conclude that the regulation of reproductive genetics is becoming more critical and complex. The aim should be to ensure good practices and equity, while providing more information to the public. A broad and inclusive societal debate may overcome the difficulty of drawing a clear line between medical uses and non-medical uses of genetic selection and engineering and may contribute to finding the right balance between allowing autonomous decisions of patients and protecting the public interest.

In this paper, a novel pendulum-type accelerometer based on hetero-core fiber optics has been proposed for structural health monitoring targeting large-scale civil infrastructures. Vibration measurement is a non-destructive method for diagnosing the failure of structures by assessing natural frequencies and other vibration patterns. The hetero-core fiber optic sensor utilized in the proposed accelerometer can serve as a displacement sensor with robustness to temperature changes in addition to immunity to electromagnetic interference and chemical corrosions. Thus the hetero-core sensor inside the accelerometer measures applied acceleration by detecting the rotation of an internal pendulum. A series of experiments showed that the hetero-core fiber sensor linearly responded to the rotation angle of the pendulum ranging within ±5°, and furthermore the proposed accelerometer could reproduce the waveform of input vibration in a frequency band of several Hz order.

myfood24 is a comprehensive self-completed online 24-hour dietary recall tool currently used for nutritional assessments in epidemiological research. However, its clinical application has been unexplored. This mixed methods prospective observational study explores the acceptability and usability of myfood24 in a clinical population, women with gestational diabetes (GDM). Women were recruited at their first diabetes antenatal clinic appointment. To assess acceptability and usability, they were asked to complete five 24-hour dietary recalls using myfood24 over two weeks and a user experience questionnaire; with a subset invited to participate in a one-to-one semi-structured interview. Of the 199 participants, mean maternal age was 33 years, mean booking BMI 29.7kg/m2, 36% primiparous, 57% White, 33% Asian. Of these 121 (61%) completed myfood24 at least once and 73 (37%) completed the user questionnaire; 15 were interviewed. Usability of myfood24 was measured using the System Usability Scale (SUS) and found to be good (mean 70.9, 95%CI 67.1, 74.6). Interviews identified several areas for improvement, including optimising its use for mobile devices. myfood24 appears to be acceptable and have potential to support self-management and behaviour change for women with GDM but requires adaptation to record blood glucose results alongside real-time tracking of diet.

We attempted to establish an objective method to accurately evaluate the motility of bull sperm and examined the effects of media for sperm suspensions and frame rates on data of computer-assisted sperm motility analysis (CASA). Sperm incubated in Brackett and Oliphant medium (BO) more clearly showed hyperactivation-like motility than those in synthetic oviductal fluid. Sperm images captured at 150 frames per second (fps) showed a trajectory that was closer to the real pathway than those at other frame rates (30, 50, and 75 fps). We then examined the characteristics of sex-sorted and non-sorted semen using a cluster analysis followed by a discriminant analysis of sperm motility in BO at 150 fps. The results indicated that sex-sorted semen contained sperm with hyperactivation-like motility as the main subpopulation immediately after thawing and this subpopulation decreased after 2-h incubation. The main subpopulation in non-sorted semen had progressive motility that was maintained during incubation. In conclusion, usage of BO for sperm suspensions and capturing sperm motility at 150 fps by CASA were appropriate for evaluating bovine sperm motility. A discriminant analysis using data from a cluster analysis of motile sperm has the ability to accurately describe differences in the structures of sperm motility subpopulations.

A novel characterization method for discrete saw filters vibrational sensitivity is presented. The proposed approach allows the characterization of filters under vibrations and the extraction of a behavioural model. Filters are assumed to be transducers so that external induced vibrational energy is partially transformed in a undesired simultaneous amplitude and phase modulation of the input RF signal. When the filter is mechanically excited with vibrations, it introduces spurious amplitude and phase modulation to the input signal that can potentially affect the link quality.

Eating disorders (EDs) are serious, life-threatening psychiatric conditions associated with physical and psychosocial impairments, as well as high morbidity and mortality. Given the chronic refractory nature of EDs and the paucity of evidence-based treatments, there is a pressing need to identify novel approaches for this population. The noncompetitive N-methyl-D-aspartate receptor (NMDAr) antagonist, ketamine, has recently been approved for treatment-resistant depression, exerting rapid and robust antidepressant effects. It is now being investigated for several new indications, including obsessive-compulsive, post-traumatic, and substance use disorder; and shows transdiagnostic potential for EDs, particularly among clinical non-responders. As such, the aim of this review is to examine contemporary findings on the treatment of EDs with ketamine, whether used as a primary, adjunctive, or combination psychopharmacotherapy. Avenues for future research are also discussed. Overall, results are encouraging and point to therapeutic value, yet are limited to case series and reports on anorexia nervosa. Further empirical work is thus needed to explore ketamine efficacy across ED subgroups; establish safety profiles and optimize dosing; and develop theory-driven, targeted treatment strategies at the individual patient level.

Animal-assisted interventions (AAI) use human-animal interactions to positive effect in various contexts including cancer care. This systematic literature review is the first part of a two-part paper series focusing on the research methods and quantitative results of AAI studies in oncology. We find methodological consistency in the use of canines as therapy animals, in the types of high-risk patients excluded from studies, and in the infection precautions taken with therapy animals throughout cancer wards. The investigated patient endpoints are not significantly affected by AAI, with the exceptions of improvements in oxygen consumption, quality of life, depression, mood, and satisfaction with therapy. The AAI field in oncology has progressed significantly since its inception and has great potential to positively impact future patient outcomes. To advance the field, AAI research in oncology should consistently improve the methodological design of studies, report data more completely, and focus on the therapy animal’s well-being.

General–purpose automatic speech recognition (ASR) systems have improved their quality and are being used for pronunciation assessment. However, the assessment of isolated short utterances, as words in minimal pairs for segmental approaches, remains an important challenge, even more for non-native speakers. In this work, we compare the performance of our own tailored ASR system (kASR) with the one of Google ASR (gASR) for the assessment of Spanish minimal pair words produced by 33 native Japanese speakers in a computer-assisted pronunciation training (CAPT) scenario. Participants of a pre/post-test training experiment spanning four weeks were split into three groups: experimental, in-classroom, and placebo. Experimental group used the CAPT tool described in the paper, which we specially designed for autonomous pronunciation training. Statistically significant improvement for experimental and in-classroom groups is revealed, and moderate correlation values between gASR and kASR results were obtained, beside strong correlations between the post-test scores of both ASR systems with the CAPT application scores found at the final stages of application use. These results suggest that both ASR alternatives are valid for assessing minimal pairs in CAPT tools, in the current configuration. Discussion on possible ways to improve our system and possibilities for future research are included.

High Brassicaceae consumption reduces the risk of developing several cancer types, probably due to their glucosinolate amount. Extracts from Sinapis nigra L. and Sinapis alba L. have been obtained from leaves and seeds under different conditions using ethanol/water mixtures because well accepted by food industry. The EtOH/H2O 8:2 mixture gives better yields in glucosinolate amounts from grinded seeds, mainly sinalbin in S. alba and sinigrin in S. nigra. The highest antiproliferative activity in both non-tumour and tumour cell lines was induced by S. alba seeds extract. To evaluate whether Sinapis spp effect was only due to glucosinolate content or it was influenced by the extracts’ complexity, cells were treated with extracts or glucosinolates, in the presence of myrosinase. Pure sinigrin did not modify cell proliferation, while pure sinalbin was less effective than the extract. The addition of myrosinase increased the antiproliferative effects of the S. nigra extract and sinigrin. Antiproliferative activity was correlated to MAPKs modulation, which was cell and extract-dependent. Cell-cycle analysis evidenced a proapoptotic effect of S. alba on both tumour cell lines and of S. nigra only on HCT 116. Both extracts showed good antimicrobial activity in disc diffusion tests and on ready-to-eat fresh salad. These results underline the potential effects of Sinapis spp in chemoprevention and food preservation.

In this research, low-fat dried Chinese sausage was formulated with mango peel pectin (MPP) extracted by microwave assisted extraction (MAE) (0%, 5%, 10% and 15% (w/w). The extractable yield of pectin attained from peel of Nam Dok Mai variety was achieved at 13.85% using 700-watt power. The extracted MPP were of high equivalent weight (1,485.78 mg/mol), degree esterification (77.19%) and methoxyl content (19.33%) with the structure of more porosity as compared to that of the conventional method. Spectrum scans by Fourier transform infrared spectrophotometer (FT-IR) advised that the extracted MPP gave the similar wave number profiles as the commercial pectin. Quality attributes of the Chinese sausages were accessed and compared with the control formula (CTRL). At higher concentrations of MPP, the product had positively increased colour intensity. The texture profile of the sausage illustrated that only the hardness value was comparable with the CTRL, while springiness, cohesiveness, gumminess and chewiness were statistically lower (p < 0.05). Furthermore, the sensory evaluation by experienced panellists (n=12) indicated that 5% MPP similarly represented overall acceptability with the CTRL. Consequently, MPP can be effectively applied at low level as fat replacement in Chinese sausage allowing colour improvement and product of healthier option.

In order to integrate genomics in breeding and development of drought tolerant groundnut genotypes, identification of genomic regions/genetic markers for drought surrogate traits is essential. We used SNP markers for a genetic analysis of the ICRISAT groundnut minicore collection for genome wide marker-trait association for some physiological traits and to determine the magnitude of linkage disequilibrium (LD) present in the genetic resources. The LD analysis showed that about 36% of loci pairs were in significant LD (P < 0.05 and r2 > 0.2) and 3.14% of the pairs were in complete LD. There was rapid decline in LD with distance and the LD was <0.2 at a distance of 41635 bp. The marker trait association (MTAs) studies revealed 20 significant MTAs (p <0.001) with 11 markers for leaf area index (4), canopy temperature (13), chlorophyll content (1) and NDVI (2). The markers explained 2 to 21% of the phenotypic variation observed. Most of the MTAs identified on the A subgenome were also identified on the respective homeologous chromosome on the B subgenome. The duplications of effect observed could be due to common ancestor of the A and B genome which explains the linkage detected between markers lying on different chromosomes seen in the current study. The present study identified a total of 20 highly significant marker trait associations with 11 markers for four physiological traits of importance in groundnut; LAI, CT, SCMR and NDVI. The markers identified in this study can serve as useful genomic resources to initiate marker-assisted selection and trait introgression of groundnut for drought tolerance. The identified markers in this study may be useful for marker assisted selection after further validation.

To gain insight into riser motions and associated fatigue damage due to vortex-induced vibration (VIV), data loggers such as strain sensors and/or accelerometers are sometimes deployed on risers to monitor their motion in different current velocity conditions. Accurate reconstruction of the riser response and empirical estimation of fatigue damage rates over the entire riser length using measurements from a limited number of sensors can help in efficient utilization of the costly measurements recorded. Several different empirical procedures are described here for analysis of the VIV response of a long flexible cylinder subjected to uniform and sheared current profiles. The methods include weighted waveform analysis (WWA), proper orthogonal decomposition (POD), modal phase reconstruction (MPR), a modified WWA procedure, and a hybrid method which combines MPR and the modified WWA method. Fatigue damage rates estimated using these different empirical methods are compared and cross-validated against measurements. Detailed formulations for each method are presented and discussed with examples. Results suggest that all the empirical methods, despite different underlying assumptions in each of them, can be employed to estimate fatigue damage rates quite well from limited strain measurements.

Objectives: Studies evaluating machine learning (ML) algorithms on cross-lingual RadLex® mappings for developing context-sensitive radiological reporting tools are lacking. Therefore, we investigated whether ML-based approaches can be utilized to assist radiologists in providing key imaging biomarkers – such as The Alberta stroke programme early CT score (APECTS). Material and Methods: A stratified random sample (age, gender, year) of CT reports (n=206) with suspected ischemic stroke was generated out of 3997 reports signed off between 2015-2019. Three independent, blinded readers assessed these reports and manually annotated clinico-radiologically relevant key features. The primary outcome was whether ASPECTS should have been provided (yes/no: 154/52). For all reports, both the findings and impressions underwent cross-lingual (German to English) RadLex®-mappings using natural language processing. Well-established ML-algorithms including classification trees, random forests, elastic net, support vector machines (SVMs) and boosted trees were evaluated in a 5 x 5-fold nested cross-validation framework. Further, a linear classifier (fastText) was directly fitted on the German reports. Ensemble learning was used to provide robust importance rankings of these ML-algorithms. Performance was evaluated using derivates of the confusion matrix and metrics of calibration including AUC, brier score and log loss as well as visually by calibration plots. Results: On this imbalanced classification task SVMs showed the highest accuracies both on human-extracted- (87%) and fully automated RadLex® features (findings: 82.5%; impressions: 85.4%). FastText without pre-trained language model showed the highest accuracy (89.3%) and AUC (92%) on the impressions. Ensemble learner revealed that boosted trees, fastText and SVMs are the most important ML-classifiers. Boosted trees fitted on the findings showed the best overall calibration curve. Conclusions: Contextual ML-based assistance suggesting ASPECTS while reporting neuroradiological emergencies is feasible, even if ML-models are restricted to be developed on limited and highly imbalanced data sets.

Regarding number of vehicles, forest roads are characterized by low traffic intensity, but on the other hand great values of ground pressure between wheels of timber truck units and forest road surface occur, often with pressures values above 80 kN which additionally causes damage of the upper and lower forest road layer. There are currently several methods for assessing condition of a forest road surface which are mainly used for assessing state of public roads, but can be used in forestry as well. Assessing condition of forest road surface was done by measuring vibrations with a specially developed software for Android OS installed on a Huawei MediaPad 7 Lite. Software measured vibrations in all three axes, coordinates of device, speed of the vehicle and time. Aim of this research was to determine accuracy of collected data so that this method can be used for scientific and practical purposes. Research was carried out on the segment of a forest road during driving a vehicle equipped with a measuring device. Tests were performed in both driving direction of the forest road segment with different measuring frequencies, tyre inflation pressures and driving speeds. Values of vibrations were classified and translated on a map of forest road together with devices’ measured coordinates. Vibration values were compared with places of recorded forest road surface damages. Research results show no significant difference in vibration values between 1 Hz and 10 Hz of measurement frequencies. Based on the analysis of collected data and obtained results, it is clear that it is possible to assess the condition of a forest road surface by measuring vibrations. The greatest values of vibrations were recorded on the most damaged parts of the forest road. Vibrations do not depend on tyre inflation pressure, but ranges of vibrations are decreasing with decreasing driving speed. Accuracy of collected data depends on GPS signal quality, so it is recommended that each segment of forest road is recorded twice so that location of damages on forest road can be confirmed with certainty.

This research was presented the special designed microfluidic device generated for sperm separation based on assumption of different surface electrical charged of sperms X and Y. However, to avoid ethical problem, the microfluidic chip has been tested with the mimic electrical charged particles, TiO₂-coated Polystyrene beads, (TiO₂-coated Ps-beads), instead of spermatozoa. The work has been separated into three main parts. Firstly, the simply but efficient fabrication of negatively charged TiO₂-coated Ps-beads has been presented. In addition, various characterization techniques such as X-ray diffraction (XRD), Tungsten Scanning Electron Microscopy (W-SEM) with energy-dispersive X-ray spectroscopy (EDS) mode, and X-ray Absorption Spectroscopy (XAS), have been reported in this work to elucidate the reasons behind the persistence of negatively charged on the surface of TiO₂-coated Ps-beads. Results show that the fabricated TiO₂-coated Ps-beads was partly coated in the mixed forms of amorphous Ti⁴⁺ and had caused a negatively charge to appear on the surface after fabrication and had sustained its electrical charged for long. Secondly, process of simulation and fabrication of microfluidic device was presented. Finally the negatively charged TiO₂-coated Ps-beads were tested in this microfluidic devices. For design of microfluidic devices integrated with a couple of microelectrodes, the simulated structures were fabricated by photolithographic technique and tested with the Ps-beads. Percentage of validation for Ps-beads separation indicated that the 100 mm-distance-between-electrodes microfluidic device exhibits to be the highest performance prototype at 86.96%. For further confirmation, another model so called the single path prototype has been established. It is confirmed by 92.59% of validation for the utilization of the device. The successfully designed microfluidic devices can be examined with actual spermatozoa later. Furthermore, process to fabricate the negatively charged TiO₂-coated Ps-beads can be established as testified samples for development of other microfluidic devices.

Study question: What are the current trends of research in Human Assisted Reproduction around the world? Summary answer: USA is the leading country, followed by the UK, China, France and Italy. The largest research area is “laboratory techniques”, although other areas such as “public health”, “quality, ethics and law” and “female factor” are gaining ground worldwide. What is known already: Scientific research, especially in health and medical sciences, aims at addressing specific needs that society (and, especially, patients) perceives as pressing. One of the main challenges for policymakers and research funders alike is therefore to align research priorities to societal needs. We can thus think of research agendas in terms of a demand side (societal needs) and a supply side (research outputs). Research output in Human Assisted Reproduction has expanded in the past years, as indicated by the increasing number of scientific publications in indexed journals in this area. Nevertheless, no map of research related to assisted reproduction has been produced so far, hindering the identification of potential areas of improvement and need. Study design, size, duration: 26,000+ scientific publications (articles, letters, and reviews) on Human Assisted Reproduction produced worldwide between 2005 and 2016 were analyzed. These publications were indexed in PubMed or obtained from reference list of indexed publications included in the analysis.Participants/materials, setting, methods: The corpus of publications was obtained by combining the MeSH terms: “Reproductive techniques”, “Reproductive medicine”, “Reproductive health”, “Fertility”, “Infertility”, and “Germ cells”. Then it was analyzed by means of text mining algorithms (Topic Modeling (TM) based on Latent Dirichlet Allocation (LDA)), in order to obtain the main topics of interest. Finally, these categories were analyzed across world regions and time. Main results and the role of chance: We identified 44 main topics, which were further grouped in 11 macro categories, form larger to smaller: “laboratory techniques”, “male factor”, “quality, ethics and law”, “female factor”, “public health and infectious diseases”, “basic research and genetics”, “pregnancy complications and risks”, “general infertility and ART”, “psychosocial aspects”, “cancer”, and “research methodology”. The USA was the leading country in number of publications, followed by the UK, China, France and Italy. Interestingly, research contents in high income countries is fairly homogeneous across macro-categories, and it is dominated by “laboratory techniques” in Western and Southern Europe, and by “quality, ethics and law” in North America, Australia and New Zealand. In middle income countries we observe that research is mainly performed on “male factor”, and noticeably less on “female factor”. Finally, research on “public health and infectious diseases” predominates in low-income countries. Regarding temporal evolution of research, “laboratory techniques” is the most abundant topic on a yearly basis, and relatively constant over time. However, since production in most of the other categories is increasing, the relative contribution of this research category is actually decreasing. Publication is especially increasing in “public health and infectious diseases” (in all world regions, but especially in low income countries), “quality, ethics and law” (high income countries), and “female factor” (middle income countries). Limitations, reasons for caution: Three main factors might limit the robustness of our work: the textual corpus analyzed is based on abstract and titles, the reproducibility of the stochastic algorithms applied, which may produce slightly differing results at each run, and the interpretation of the topics obtained. Wider implications of the findings: This study should prove beneficial in the design of research strategies and policies that foster the alignment between supply (assisted reproduction research) and demand (society). Study funding/competing interest(s): PTQ-14-06718 of the Spanish MINECO Torres Quevedo programme (FAM).

In this study, a tuned mass damper is proposed as a seismic acceleration mitigating technique of an electrical cabinet inside the nuclear power plant. In order to know the mitigation performance, the electrical cabinet and the tuned mass damper were modeled using SAP2000. The sine sweep wave was used to confirm the vibration characteristics of the cabinet over a wide frequency range, and the several various earthquakes were applied to the cabinet to verify the control performance of the tuned mass damper. After analyzing the numerical results, it is summarized that the application of the proposed technique can reduce the acceleration response of the cabinet.

Fatty acids (FAs) represent an important class of metabolites, impacting on membrane building blocks and cellular regulatory networks. In nature, prokaryotes are characterized with the most impressing FA structural diversity and the highest relative contents of free fatty acids (FFAs). Thereby, nitrogen-fixing bacteria (order Rhizobiales), often found in symbiosis with legumes, attract a special interest. Indeed, FAs impact on the structure of rhizobial nodulation factors, required for successful infection of plant root. Although the FA patterns can be addressed by GC- and LC-MS, these methods are time-consuming and suffer from compromised sensitivity, low stability of derivatives and artifacts. In contrast, MALDI-TOF-MS represents an excellent platform for high-efficient metabolite fingerprinting, also applicable to FFAs. Therefore, here we propose a simple and straightforward protocol for high-throughput relative quantification of FFAs in rhizobia by the combination of Langmuir technology and MALDI-TOF-MS, which is featured with high sensitivity, accuracy and precision of quantification. Here we propose a step by step procedure comprising rhizobia culturing, pre-cleaning, extraction, sample preparation, mass spectrometric analysis, data processing and post-processing. To demonstrate the analytical potential of the protocol we illustrate it by a case study – comparison the FFA metabolomes of two rhizobia species - Rhizobium leguminosarum and Sinorhizobium meliloti.

STRAS (Single access Transluminal Robotic Assistant for Surgeons) is a flexible robotic system based on the Anubis® platform of Karl Storz for application to intra-luminal surgical procedures. It consists of three cable-driven systems, one endoscope serving as guide and two inserted instruments. The flexible and bendable instruments have three degrees of freedom and can be teleoperated by a single user via two specially designed master interfaces. In this research, a pair of specific sensor gloves, which ergonomically fit to the master handles of the system was designed and the forces applied by one expert and one novice user during system-specific task execution in a simulator task (4-step-pick-and-drop) were compared. The results show that user expertise is not only reflected by shorter task execution times but also, more importantly, by specific differences in handgrip force profiles for specific sensor locations on anatomically relevant parts of the fingers and hand controlling the surgical instruments of the robotic master/slave system.

With the development of Internet technology, teachers are constantly seeking innovative teaching methods to match the potential of enhanced technology. Although many studies have been performed before , they aren’t enough in this field. The purpose of this paper is to explore innovative teaching designs and examine the impact of Internet-assisted English teaching of reading based on constructivism. The case is carried out in NO.9 middle school of Bengbu, a underdeveloped area of China, most of students aren’t interested in learning English .We compared Internet-assisted with traditional textbook literature methods to improve the reading proficiency of students, using a questionnaire survey,pre-test and post-tests comparisons. The result showed Internet-assisted English reading teaching is better than textbook. It can arouse students' interest and motivation,reading proficiency and exam result of students have been improved significantly, created a positive learning situation.

The performance of the absolute atom gravimeters used on moving platforms, such as vehicles, ships and aircrafts, is strongly affected by the vibration noise. To suppress its influence, we summarize a vibration compensation method utilizing data measured by a classical accelerometer. The measurements with the accelerometer show that the vibration noise in the vehicle can be 2 order of magnitude greater than that in the lab during daytime, and can induce an interferometric phase fluctuation with a standard deviation of 16.70π. With the compensation method, our vehicle-mounted atom gravimeter can work normally in these harsh conditions. Comparing the Allan standard deviations before and after the vibration noise correction, we find a suppression factor of 22.74 can be achieved in static condition with an interrogation time of T = 20 ms, resulting a sensitivity of 1.35 mGal/Hz1/2, and a standard deviation of 0.5 mGal with an average time of 10 s. We also demonstrate the first test of an atom gravimeter in a moving vehicle, in which a suppression factor of 50.85 and a sensitivity of 60.88 mGal/Hz1/2 were realized with T = 5 ms.

Nymphaea lotus L. is the medicinal plant that has long been used as food, cosmetic and traditional medicines in Africa and Asia since the ancient time. Its flavonoids and other interesting phytochemical compounds from rhizome, leaf, and the whole flowers have been reported in the previous published researches. However, stamens, which are essential for reproductive functions, may also represent new alternative sources of potential antioxidant flavonoids as investigated in this study. The innovative green chemistry method i.e. ultrasound-assisted extraction (USAE) as well as macroporous resin (MPR) purification procedure were employed in this current research. The optimal ultrasound-assisted extraction condition is 90 % (v/v) aqEtOH with 34.65 khz ultrasonic frequency and 46 minutes of extraction time. Comparing with heat reflux extraction (HRE) conventional method, the significant gain of 1.35 total flavonoids content was obtained using optimized USAE conditions, jumping to 2.80 when this USAE associated with MPR purification. Not only in vitro cell free antioxidant activity of N. lotus stamen extracts, but also in cellulo antioxidant investigation using yeast model showed the same trend to indicate that the best antioxidant flavonoid can be found in USAE coupled with MPR purification. Moreover, the key antioxidant genes expression in yeast model such as SIR2 and SOD2 were also expressed at the highest level in yeast cell treated with the extract from USAE together with MPR purification. Consequently, it can be seen that the USAE combined with MPR purification can help to enhance the flavonoids antioxidant potential of the stamens extract from this medicinal species.

Background: We assess locoregional drug targeting effectiveness of intraoperative (IO) cryoprobe-assisted injection of blue dye (BD) and cytotoxic-tracer mixture (TTM), in VX2 tumor model, and its translational value to cryo-assisted breast tumor surgery with BD alone. Methods: Under computed tomography (CT) guidance, we injected two ml TTM in five aliquots in the margin of 16 frozen or normothermic VX2 tumors. We evaluated the IO and post-operative drug targeting and therapeutic efficacy in tumor-host interface (T-HI) by CT, gross examination, and histopathology. In twenty-six T1 to T4 primary breast cancer (BRCA) we performed ultrasound-guided (US) cryoprobe-assisted tumor freezing, BD guided lymphatic mapping, and surgery. We evaluated, IO and in freshly resected specimen, BD distribution pattern in T-HI, lymph node(s), breast parenchyma, and resection cavity. Results: Fluids-impervious frozen VX2 or breast tumor transported drug(s) an arc-like pattern at T-HI regardless of freeze dose, number of freeze-thaw cycles, drug dose fractionation, tumor characteristics or dimensions. During melting, TTM spread within fifty percent VX2 tumor mirrored that of T-HI; it was massive in normothermia. In VX2 twenty percent focal margin necrosis at pathology coincided with CT gap; in both studies, BD dose-staining spread in T-HI and tumor was linear. Eighty-four patients had one to twelve stained axillary lymph nodes; sixty-nine percent and all respectively, had another quadrant and resection cavity stained. Conclusion: Intraoperative freezing-assisted drug delivery and targeting techniques during cryoablation of VX2 tumor translate successfully to locoregional BD targeting, lymphatic mapping during cryo-assisted surgery of breast cancer.

This paper investigates the problem of the optimal arrangement for both UAVs’ caching contents and service locations in UAV-assisted networks based on the context awareness, which considers the influence between users and environment. In the existing work, users within the coverage of UAVs are considered to be served perfectly, which ignores the communication probability caused by line-of-sight (LOS) and non- line-of-sight (NLOS) links. However, the links are related to UAV deployment. Moreover, the transmission overhead should be taken into account. To balance the tradeoff between these two factors, we design the ratio of users’ probability and transmission overhead as the performance measure mechanism to evaluate the performance of UAV-assisted networks. Then, we formulate the objective for maximizing the performance of UAV-assisted networks as a UAV-assisted caching game. It is proved that the game is an exact potential game with the performance of UAV-assisted networks serving as the potential function. Next, we propose the log-linear caching algorithm (LCA) to achieve the Nash equilibrium (NE). Finally, related simulation results reflect the great performance of the proposed algorithm.

Background: Elucidation of epigenetic mechanisms correlating with neuropathic pain in humans is crucial for the prevention and treatment of this treatment-resistant pain state. In the present study, associations between neuropathic pain characteristics and DNA methylation of the transient receptor potential ankyrin 1(TRPA1) gene were evaluated in chronic pain patients and preoperative patients. Methods: Pain and psychological states were prospectively assessed in patients who suffered chronic pain or were scheduled for thoracic surgery. Neuropathic characteristics were assessed using the Douleur Neuropathique 4 (DN4) questionnaire. DNA methylation levels of the CpG island in the TRPA1 gene were examined using whole blood. Results: Forty-eight adult patients were enrolled in this study. Increases in DNA methylation rates at CpG -51 showed positive correlations with increases in the DN4 score both in preoperative and chronic pain patients. Combined methylation rates at CpG -51 also significantly increased together with increase in DN4 scores. Conclusions: Neuropathic pain characteristics are likely associated with methylation rates at the promoter region of the TRPA1 gene in human peripheral blood.

For a given material, different shapes correspond to different rigidities. In this paper, the radii of the oblique elliptic torus are formulated, a nonlinear displacement formulation is presented and numerical simulations are carried out for circular, normal elliptic, and oblique tori, respectively. Our investigation shows that both the deformation and the stress response of an elastic torus are sensitive to the radius ratio, and indicate that the analysis of a torus should be done by using the bending theory of shells rather than membrance theory. A numerical study demonstrates that the inner region of the torus is stiffer than the outer region due to the Gauss curvature. The study also shows that an elastic torus deforms in a very specific manner, as the strain and stress concentration in two very narrow regions around the top and bottom crowns. The desired rigidity can be achieved by adjusting the ratio of minor and major radii and the oblique angle.

This study presents a novel technique utilizing high frequency vibration to shorten treatment time and preserve alveolar bone in challenging orthodontic cases treated with Invisalign® clear aligners. Four non-growing orthodontic patients (age range 14-47 years old) with Class II skeletal patterns (convex profiles with retrognathic mandibles) who sought correction of their crowded teeth and non-surgical correction of their convex profiles were included in this study. These patients were treated using Invisalign clear aligners together with high frequency vibration (HFV) devices (120 Hz) (VPro5™) that were used by all patients for five minutes per day during active orthodontic treatment. Vertical control and forward rotation of the mandible for each patient was achieved through pre-programming the Invisalign to produce posterior teeth intrusion. Successful forward rotation of the mandibles achieved in all patients led to improvement of their facial convex profiles (ANB improved 2.1 + 0.5 degrees; FMA improved 1.2 +1.1 degrees). Dental decompensation was achieved by lingual tipping of the lower incisors and palatal root torque of upper incisors. The use of HFV together with Invisalign facilitated achieving these results within a 12+6 month period. In addition, more bone labial to the lower incisors after their lingual movement was noted. In conclusion, the use of HFV concurrent with SmartTrack Invisalign aligners allowed complex tooth movement and forward projection without surgery in non-growing patients with skeletal Class II relationships. The clinical impact and implications of this case series is that the use of HFV facilitates complex orthodontic tooth movement including posterior teeth intrusion and incisor decompensation in addition to increased bone formation labial to lower incisors that may minimize future gum recession due to their labial inclination.

Silybum marianum (L.) Gaertn. (aka milk thistle) constitute the almost exclusive source of silymarin, a mixture of different flavonolignans, and is thus considered as a unique model for their extraction. The present research deals with ultrasound-assisted extraction (UAE) of S. marianum flavonolignans and their quantification using LC system. The optimal conditions for UAE were: aqueous EtOH 54.5% (v/v) as solvent, applying an ultrasound frequency of 36.6 kHz during an extraction time of 60 min at 45°C with a liquid to solid ratio of 25:1 ml/g DW. Following optimization, the extraction method was validated according to international standards of the association of analytical communities (AOAC) in order to ensure its precision and accuracy for the quantitation of the individual silymarin components. The efficiency of UAE was compared with maceration protocol of the same duration. The optimized and validated conditions allowed highest extraction yields of flavonolignans in comparison to maceration. The antioxidant capacity of the extracts was confirmed by the CUPRAC assays and inhibition of advanced glycation end products. The skin anti-aging action was also confirmed toward the strong in vitro inhibition capacity of the obtained extract against collagenase and elastase enzymes. The procedure presented here allows a green efficient extraction and quantification of the main flavonolignans from the fruits of S. marianum with attractive antioxidant and anti-aging activities for future cosmetic applications.

Our wellbeing is greatly influenced by our childhood and adolescence, and the relationships that we form during those phases of our development. The human-dog bond started thousands of years ago. The higher prevalence of dog ownership around the world, especially in households including children along with the growing number of people studying dogs most likely explain the growing literature focusing on child-dog interactions. We review the potential effects of child-dog interactions on the physical, mental, and social wellbeing of both species. A scoping search of the SCOPUS database found several hundred documents meeting selection criteria. It allowed us to define the numerous ways in which children and dogs can interact, be it neutral (e.g., sharing a common area), positive (e.g., petting), or negative (e.g., biting). Then, we found evidence for an association between interacting with dogs during childhood and an array of health and mental benefits like stress relief and the development of empathy. Walking a dog and playing with one are perfect physical activity opportunities. Additionally, interacting with a dog can help lower stress and may have a role in the development of empathy. Nonetheless, a number of detrimental outcomes have also been identified in both humans and dogs. Children are the most at-risk population regarding dog bites and dog-borne zoonoses, which may lead to a subsequent fear of dogs or even death. Moreover, pet bereavement is generally inevitable when living with a canine companion and should not be trivialized. In terms of dogs, children sometimes take part in caretaking behaviors toward them which include going on walks. They are opportunities for dogs to relieve themselves outside, but also to exercise and socialize. In contrast, a lack of physical activity can lead to the onset of obesity. Dogs may present greater levels of stress when in the presence of children. Finally, the welfare of assistance, therapy, and free-roaming dogs remains underexplored. Overall, the study of the effects, positive as well as negative, on both species still requires further development. We call for more longitudinal studies and hope for cross-cultural research in the future in order to better understand the impact child-dog interactions might have.

Focal vibration therapy can provide neurophysiological benefits. Unfortunately, standardized protocols are non-existent. Previous research presents a wide range of protocols with a wide range of effectiveness. This paper is part of a broader effort to identify effective, standardized protocols for focal vibration therapy. The vibration characteristics of four commercially available focal vibration devices that have been used for research and clinically were measured. An accelerometer was used for the measurements. Frequency and peak-to-peak amplitude were measured. Measurements were made when the devices were free and then again when they were strapped to the human body. Vibration frequency ranged from 120 to 225 Hz. Free vibration amplitude ranged from 2.0 to 7.9 g’s (peak-to-peak). When the devices were strapped to the body (constrained), vibration amplitude decreased by up to 65.7%. These results identify effective ranges of focal vibration frequency and amplitude. They illustrate the importance of identifying vibration environment, free or constrained, when quoting vibration characteristics. Finally, the inconsistency of multi-actuator devices is discussed. These results will guide protocol development for focal vibration and potentially better focal vibration devices.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

Age-in-place can reduce the progress of dementia syndrome and improve the quality of life of the sufferers and their families. This work proposes an innovative information home support system to be established at the houses of people suffering from dementia. The main innovation of the system are its transparent character that overcomes the need for training of the sufferer, as well as the exploitation of a well-known technique for dementia, namely music therapy. It addresses the need of people suffering from dementia as well as their familiars to be recognized by them and have better interaction and collaboration. The system offers a ubiquitous recognition system, just by using smart devices like smart-phones or smart-wristbands. When a familiar person is detected in the house, then a sound file is reproduced on smart speakers placed in the house, in order to trigger the memory, based on the principles of music therapy. The system reproduced the appropriate time at 100% of the cases and the benefits of music therapy are evident daily. To the best of the authors' knowledge, this is the first system of its kind ever reported in the literature.

Smart living, a concept that has gained increasing attention in recent years, revolves around integrating advanced technologies in homes and cities to enhance the quality of life for citizens. Sensing and human action recognition are crucial aspects of this concept. Smart living applications span various domains, such as energy consumption, healthcare, transportation, and education, which greatly benefit from effective human action recognition. This field, originating from computer vision, seeks to recognize human actions and activities using not only visual data but also many other sensor modalities. This paper comprehensively reviews the literature on human action recognition in smart living environments, synthesizing the main contributions, challenges, and future research directions. This review selects five key domains: Sensing Technology, Multimodality, Real-time Processing, Interoperability, and Resource-Constrained Processing, as they encompass the critical aspects required for successfully deploying human action recognition in smart living. These domains highlight the essential role that sensing and human action recognition play in successfully developing and implementing smart living solutions. This paper serves as a valuable resource for researchers and practitioners seeking to explore further and advance the field of human action recognition in smart living.