In this work, a ferrocene-containing gallic acid derivative modified carbon nanotubes paste electrode (Gal-Fc-CNT) obtained by simple mechanical mixing was studied for fast simultaneous voltammetric detection of doxorubicin (DOX), capecitabine (CPB) and cyclophosphamide (CPP) as cytostatic index by cumulative signal and selective detection of DOX. The electrochemical behaviors of individual and simultaneous DOX, CPB and CPP studied by cyclic voltammetry (CV) on Gal-Fc-CNT electrode at various pHs and potential ranges allowed the development of simple simultaneous detection method as cytostatic index at pH of 12 using square-wave voltammetry technique operated at modulation amplitude of 100 mV, step potential of 4 mV, frequency of 25 Hz and 100 mV·s−1 potential scan rate that allowed better performance than reported electrodes. Faster and selective detection of DOX with the lowest limit of detection of 75 ng⸱L-1 was achieved using square-wave voltammetry technique operated at modulation amplitude of 100 mV, step potential of 4 mV, frequency of 50 Hz and 200 mV·s−1 potential scan rate. The good results obtained for real tap water assessment indicated the utility of Gal-Fc-CNT paste electrode for practical applications (water samples, pharmaceutical formulations).

The dopamine and uric acid are primary products of purine metabolism and they coexist in serum and the extracellular fluid of the central nervous system. Some diseases of the human body are due to abnormal levels of uric acid and dopamine. Thus, the clinical diagnosis of some diseases needs a sensitive and simultaneous analysis of uric acid and dopamine. In this study, a novel conductive composite film containing multi-walled carbon nanotubes (MWTs) with cooper phthalocyanine attached to acrylate polymer (MWCNTs-CuMAPC-PnBA) was fabricated and dropped on a glassy carbon electrode and used for the simultaneous determination of Uric Acid (UA) and dopamine (DA). The modified glassy carbon electrode showed satisfactory electrocatalytic activity toward dopamine and uric acid. Low detection limits were achieved at 0.174 µM of DA and 6.87 µM of UA and the linear detection ranges of DA and UA are 5-200 µM and 20-250 µM respectively. The proposed sensing system based on the modified GCE offers promising results for rapid, cost-effective and selective simultaneous detection of uric acid and dopamine. Also, the complex modified electrode showed satisfactory results to detecting simultaneously UA and DA in real human samples (human Urine) via the standard addition method.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Since Hydrogen Sulfide (H2S) was recognized as a gas transmitter, its detection and quantifica-tion have become a hot research topic among chemists and biologists. In this area. fluorescent probes have shown great advantages: fast and strong responds, low detection limit and easy ma-nipulation. Here we developed a new fluorescent probe that detected H2S selectively among various bioactive and inorganic salts. This probe was based on the core structure of fluorescein and reacted with H2S through azide-reduction. Great linearity was achieved correlating fluores-cence intensity and H2S concentrations in solution. The detection of H2S in cancer cells was also achieved.

Fluorescent carbon dots (C-dots) were synthesized by one pot hydrothermal treatment of garlic juice at 180 °C for 7h. The as-prepared C-dots with an average diameter of 2.13±0.71 nm can be well dispersed, and show absinthe fluorescence with a quantum yield of 8.9% in water. The C-dots were fully characterized by TEM, XPS, XRD, and FTIR, respectively. Additionally, the as-prepared C-dots reveal nearly nontoxic to SW480 cells and can be used for cell imaging. The water solution of C-dots show sensitivity to pH values and metal ions, and also have a high selectivity to the Hg²⁺ ion among other transition metal ions, and achieve a high sensitive detection with the detection limit of 0.45 μM. The fluorescent C-dots are expected to be useful for the evaluation of mercury ions in environmental water system.

The selectivity in the simultaneous detection of ascorbic acid (AA), dopamine (DA), and uric acid (UA) has been an open problem in the biosensing field. Many surface modification methods were carried out for glassy carbon electrodes (GCE), including the use of graphene oxide and amino acids as a selective layer. In this work, molecular dynamics (MD) simulations were performed to investigate the role of serine oligomers on the selectivity of the AA, DA, UA analytes. Our models consisted of a graphene oxide (GO) sheet under a solvent environment. Serine tetramers were added into the simulation box and were adsorbed on the GO surface. Then, the adsorption of each analyte on the mixed surface was monitored from MD trajectories. It was found that the adsorption of AA was preferred by serine oligomers due to the largest number of hydrogen-bond forming functional groups of AA, while UA was the least preferred due to its highest aromaticity. Finally, the role of hydrogen bonds on the electron transfer selectivity of biosensors was discussed with some previous studies.

This paper examines the indirect effect of democracy on economic growth using a dataset of 17 MENA countries from 1990 to 2015. Democracy is assumed to affect growth through a series of channels: education, health, physical capital accumulation per labor, government consumption, and trade openness. A system of six simultaneous equations, 3SLS, is used to estimate the effect of democracy on growth through these channels. For further analysis, the countries are classified into groups according to the democratic status on the one side, and the level of income on the other. The results indicate that democracy enhances growth through its positive effect on health in all classifications of countries within the MENA region. However, the effect of democracy on growth through education and physical capital/labor is non-monotonic. Democracy always hinders growth through government size and trade openness. Once all of these indirect effects are accounted for, the overall effect of democracy on growth is negative in less democratic countries and poor countries, but positive in more democratic countries and rich countries.

Introduction: Increasing cannabis legalization raises concerns that tobacco use, frequently used with cannabis, will also increase. This study investigated the association between legal status of cannabis in place of residence and prevalence of cannabis and tobacco co-use, simultaneous use, and mixing by comparing the prevalence among adults in Canada (prior to cannabis legalization) vs. adults in US states that had legalized recreational cannabis vs. US states that had not as of September 2018. Methods: Data were drawn from the 2018 International Cannabis Policy Study, conducted with respondents aged 16-65 in Canada and the US recruited from non-probability consumer panels. Differences in the prevalence of co-use, simultaneous use, and mixing between tobacco and different cannabis products were examined using logistic regression models by legal status of place of residence among past 12-month cannabis consumers (N=6744). Results: Co-use and simultaneous use in the past 12 months were most common among respondents in US legal states. Among cannabis consumers, co-use and simultaneous use were less common in US legal states, while mixing was less frequent in US states with both legal and illegal cannabis compared to Canada. Use of edibles was associated with lower odds of all three outcomes, while smoking dried herb or hash was associated with higher odds. Conclusions: The proportion of cannabis consumers who used tobacco was lower in legal jurisdictions despite higher prevalence of cannabis use. Edible use was inversely associated with co-use suggesting that edible use does not appear to be associated with increased tobacco use.

In this article, an iterative method of two step is proposed for finding all roots simultaneously of polynomial equations. The order of convergence of the proposed algorithm is 2m, by using any iterative scheme of order m. Numerical tests are performed to confirm the theoretical results and to compare the proposed scheme with existing methods for finding all roots simultaneously.

The scalar meson f0(980) has been a long-standing puzzle in light hadron physics. The mass and width of the f0(980) in normal decay processes are estimated to be M=990±20 MeV/c2 and Γ=40−100 MeV, respectively. Theoretically, the internal structure of the f0(980) is proposed to be a conventional quark-antiquark meson, tetraquarks state, KK¯ molecule, or quark-antiquark gluon hybrid. So far, explanations about the nature of f0(980) have been controversial for a long time. Recently, anomalously narrow width f0(980) were observed by the BESIII experiment in five independent isospin-violating decay channels. Based on the experimental data, we performed a simultaneous fit to ππ invariant mass distributions, and the mass and width in isospin-violating decays are determined to be M=990.0±0.4 MeV/c2 and Γ=11.4±1.1 MeV, respectively. In addition, we use the parameterized Flatté formula to simultaneously fit the same ππ invariant mass distributions, the two coupling constants of gfππ and gfKK¯ are measured to be gfππ=0.46±0.03 and gfKK¯=1.24±0.32, respectively. According to the joint confidence regions of gfππ and gfKK¯, we conclude that the experimental data tend to support the KK¯ molecule model and the quark-antiquark (qq¯) model, but tend not to support the tetraquarks (q2q¯2) model and the quark-antiquark gluon (qq¯g) hybrid model.

This article summarizes studies using the AIQS-DB method to analyze various types of samples for different purposes. This is a method developed to simultaneously analyze nearly 1500 compounds and is widely used worldwide. The method is highly effective for environmental samples such as water, soil, sediment, and air. Recognizing its potential, this article aims to promote the further application and development of AIQS-DB in research related to food analysis and source tracing. Furthermore, if a suitable dataset can be constructed, it could help research quickly and cost-effectively discover the new bioactive compounds from plant medicine.

In this paper, the classical least square (CLS) method with molecular absorption spectrophotometric measurement was used to determine simultaneously of paracetamol (PAR), ibuprofen (IBU), and caffeine (CAF) in tablets. The absorbance spectra of the standard solutions and samples were measured over a wavelength from 220 to 300 nm with a 0.5 nm step. The concentration of PAR, IBU and CAF in the sample solutions were calculated by using a program called CLS-Excel written in Microsoft Excel 2016 and Visual Basic for Applications (VBA). The method and CLS-Excel program were tested on mixed standard laboratory samples with different PAR, IBU, and CAF concentration ratios, and they showed small errors and satisfying repeatability. An analytical procedure for tablets containing PAR, IBU, and CAF was developed. The reliability of the procedure was proved via the recovery and repeatability of the analysis results with an actual tablet sample and comparing the mean contents of active substances in the tablets obtained from the analytical procedure with the from the HPLC method. The procedure is simple with a reduced cost compared with the HPLC standard method.

Purpose: In recent years, there has been an increasing interest in simultaneous hip and knee arthroplasty compared to staged procedures. The aim of this study was to clarify some controversies and show the safety for the patients by comparing the transfusion rate, postoperative hemoglobin drop, length of stay (LOS), in-hospital complications, 30-day readmissions, and early functional outcome after simultaneous and staged hip and knee arthroplasty. Methods: We conducted a retrospective trial that included all patients who were undergoing primary TKA, THA, and UKA by one single surgeon in a high-volume arthroplasty center between 2017 and 2020 as a simultaneous or staged procedure. Staged bilateral arthroplasties were performed within 12 months and were stratified by the time between procedures. Data was acquired through the electronic files at the OCM. For functional outcome, we compared the ability of the patients to walk independently on the ward and the ability to walk a set of stairs alone which was daily recorded by the attending physiotherapist. Results: In total 305 patients were assessed for eligibility and included in this clinical trial. 145 patients were allocated to the staged arthroplasty group. That group was subdivided in a hip and a knee group, whereas the knee group was split in TKA and unicompartmental knee arthroplasty (UKA). The second staged procedure was performed within 12 months of the first procedure.160 patients were allocated to the simultaneous arthroplasty group. This group was also subdivided into a hip and knee group, whereas the knee group was split again into a TKA and UKA group. No statistical difference was found between the two groups regarding demographic data. Primary outcome measurements: There is no significant difference in transfusion rate or complication rate. Secondarily: No correlation was found between the Hb-drop and the functional outcome as well as the length of stay (LOS). Walking the stairs showed a significant difference in the knee group. Conclusion: We observed no significant differences in transfusion rate, in-hospital complications, as well as readmission rate. The early functional outcome showed no significant difference in mobility for all groups. Simultaneous arthroplasty for knee or hip is as safe as a staged procedure, with no higher risk for the patient and his outcome, in a high-volume center.

Achieving effective control over microbial contamination necessitates the precise and concurrent identification of numerous pathogens. In this research, we have devised a remarkably sensitive duplex droplet digital PCR (dddPCR) reaction system to simultaneously detect Pseudomonas aeruginosa (P. aeruginosa) and Pseudomonas fragi (P. fragi). Employing comparative genomics, we identified four genes of P. fragi. By specific analysis, RS22680 gene was selected as the detection target of P. fragi and LasR gene was chosed as P. aeruginosa, which were applied to construct a dddPCR reaction. In terms of specificity, sensitivity and anti-interference ability, the constructed dddPCR detection system was verified and analyzed. The assay showed excellent sensitivity and applicability, as evidenced by a limit of detection of 100 CFU/mL. When the concentration of natural background bacteria in milk or fresh meat was 100 times that of the target detection bacteria, the method was still capable of completing the absolute quantification. In the simulation of actual sample contamination, P. aeruginosa could be detected after 3 h of enrichment culture, and P. fragi could be detected after 6 h. The established ddPCR detection system exhibits exceptional performance, serving as a foundation for the simultaneous detection of various pathogenic bacteria in food products.

The outbreak of coronavirus 2 (SARS-CoV-2) has already taken on pandemic proportions and has affected more than 100 countries in recent weeks. It is imperative that global healthcare systems are prepared. Containment initiatives in Jordan, on the other hand, have decreased new cases by over 63%. The Jordanian national health system has been very pleased with its ability to adequately meet the needs of the patients diagnosed with SARS-CoV-2 pneumonia, and includes intensive care. From 2 March to 14 April 2020, between 4% and 8% of active infected patients in Jordan registered daily in intensive care. The percentage is very low.

The photocatalytic biohydrogen generation using ZnO with the aid of simultaneous deposition of copper from an aqueous biomass-derivative glycerol solution was investigated. The effects of concentration of glycerol solution, Cu ion concentration and reaction temperature on biohydrogen generation were investigated. The photocatalytic biohydrogen production rate increased with increasing the concentration of aqueous glycerol solution, and the observed data could be fitted to the Langmuire-Hinshelwood kinetic models. The photocatalytic H2 production efficiency with ZnO could be significantly improved by simultaneous Cu deposition. The photocatalytic biohydrogen production rate was dependent on temperature, and increased with the increasing temperature. The possible mechanisms for oxidation of glycerol solution and photocatalytic hydrogen generation were proposed.

Untargeted and targeted approaches are the traditional metabolomics workflows acquired for a wider understanding of the metabolome under focus. Both approaches have their strengths and weaknesses. The untargeted, for example, is maximizing the detection and accurate identification of thousands of metabolites, while the targeted is maximizing the linear dynamic range and quantification sensitivity. These workflows, however, are acquired separately, so researchers compromise either a low-accuracy overview of total molecular changes (i.e., untargeted analysis) or a detailed yet blinkered snapshot of a selected group of metabolites (i.e., targeted analysis) by selecting one of the workflows over the other. In this review, we present a novel single injection simultaneous quantitation and discovery (SQUAD) metabolomics that combines targeted and untargeted workflows. It is used to identify and accurately quantify a targeted set of metabolites. It also allows data retro-mining to look for global metabolic changes that were not part of the original focus. This offers a way to strike the balance between targeted and untargeted approaches in one single experiment and address the two’s limitations. This simultaneous acquisition of hypothesis-led and discovery-led datasets allows scientists to gain more knowledge about biological systems in a single experiment.

Management of synchronous colorectal cancer with liver metastases (SCLM) is still on debate, regarding timing, indications and complications of the 3 strategies: classic approach (first tumor resection), simultaneous resection and reverse approach (liver first). A retrospective single-centre evaluation of synchronous approach was accomplished, focusing on surgical technique, indications and perioperative complications. Between 2017 and 2020, 31 SCLM patients benefited from synchronously colorectal and hepatic approach: segmental colectomies/rectal resections, simultaneously with liver metastasectomies (associated with radiofrequency ablation). Post-therapeutic imaging monitoring was performed from every 3 to 6 months. There were no perioperative complications related to the combination of the two procedures, low morbidity and zero postoperative mortality. The follow-up period was from 10 to 40 months: 13 patients had no evidence of recurrence, 10 patients had hepatic metastases in regression, 4 of them had signs of peritoneal carcinomatosis and 4 patients showed progression of liver disease; all patients were on chemotherapy. During follow-up 4 patients died. Experience shows that the simultaneous approach of recto-colic and hepatic resections in colo-rectal cancers is a safe procedure, with low morbidity, the limits being dictated by the size of the liver metastases. The results at long-distance must be drawn by further consistent trials.

Synthetic cannabinoids are a series of synthetic substances that mimic the effects of natural cannabinoids and produce a much stronger toxicity than natural cannabinoids, which have become the most abused family of new psychoactive substances. A solid-phase extractive-liquid chromatography-triple quadrupole/linear ion trap mass spectrometry method was developed to determine 11 synthetic cannabinoids in rat urine. The factors affecting recovery were optimized, and Oasis HLB was selected to extract synthetic cannabinoids simultaneously. The results showed that the linear correlation coefficients of the synthetic cannabinoids ranged from 0.993 to 0.999, and the limit of quantitation ranged from 0.01 to 0.1 ng/mL, and the spiked recoveries ranged from 69.90% to 118.39%. This method has the advantages of good purification ability, simple operation, and good reproducibility, and can be used for the high sensitivity analysis of various synthetic cannabinoids in urine.

In this paper, the lamellar structural evolution and microvoids variations of β-iPP during the processing of two different stretching methods, sequential biaxial stretching and simultaneous biaxial stretching, were investigated in detail. It was found that different stretching methods led to significantly different lamellae deformation modes, and the microporous membranes obtained from the simultaneous biaxial stretching exhibited better mechanical properties. For the sequential biaxial stretching, abundant coarse fibers originated from the tight accumulation of the lamellae parallel to the longitudinal stretching direction, whereas the lamellae perpendicular to the stretching direction were easily deformed and separated. Those coarse fibers were difficult to be separated to form micropores during the subsequent transverse stretching process, resulting in a poor micropores distribution. However, for the simultaneous biaxial stretching, the β crystal had the same deformation mode, that is, the lamellae distributed in different directions were all destroyed, forming abundant microvoids and little coarse fibers formation.

This research investigates Haifa ports emissions’ contribution to the existing daily emission inventory level in the area. This research based on developed full bottom-up model framework that looks at the single vessel daily voyage through its port call stages. The main data sources for vessels movements used in this research are the Israel Navy`s movements log and Israel Administration of Shipping and Ports’ (ASP) operational vessel movements and cargo log. The Fuel Consumption (FC) data and Sulfur Content (SC) levels are based on an official Israel ASP survey data. Observation years in this research are 2010 - 2018 with focus on the Ocean-Going Vessels (OGV) type only. The results show that the vessel fleet calling at Israel ports is mainly vessels that have a lower engine Tier grade (i.e., Tier 0 and 1) which is considered a heavy contributor to Nitrogen Oxides (NOx) pollutant. The study recommends on an additional cost charged (selective tariff) to reflect the external social cost linked to the single vessel air pollution combined with supportive technological infrastructure and economic incentive tools (e.g. electric subsidy) to attract or influence vessel owners to assign vessels equipped with new engine Tier grades for calls at Israeli ports.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

Conservation agriculture and conservation tillage have drawn the attention not only of scientists but of politicians and societies worldwide. This paper aims to present a method for selecting re-search studies on conservation agriculture, conservation tillage, and the role of straw residues on soil health and soil stability against climatic hazards. VOSviewer version 1.6.18 free software tool was used in this study to achieve the bibliometric and mapping approach for studies on the effects of climate change in terms of conservation, tillage, soil health, and straw and microbe or straw and climate interaction or other paradigms. Scopus database (accessed July 7, 2023) indexed a total of 752.2018 bibliographic items classified into 15 paradigms e.g., Carbon (AND Straw) or Microbes (AND Straw). From the examination of the selected papers, it was concluded that straw residue has an impact on soil's physical, chemical, and biological properties and the environment in general.

Autophagy was initially recognized as a bulk degradation process that randomly sequesters and degrades cytoplasmic material in lysosomes (vacuoles in yeast). In recent years, various selective autophagy pathways have been discovered. Glycophagy, the selective autophagy of glycogen granules, is one of them. It is an important contributor to Pompe disease, a type of lysosomal storage disorder with lysosomal accumulation of glycogen. Here, we developed the Komagataella phaffii yeast as a simple model of glycogen autophagy under nitrogen starvation conditions. For this, we turned the self-glucosylating initiator of glycogen synthesis, Glg1, which is covalently bound to glycogen, into the Glg1-GFP autophagic reporter. Our results revealed that vacuolar delivery of Glg1-GFP and its processing to free GFP were strictly dependent on autophagic machinery and vacuolar proteolysis. Notably, this process was independent of Atg11, the scaffold protein common for many selective autophagy pathways. Importantly, the non-mutated Glg1-GFP (which synthesizes and marks glycogen) and mutated Glg1Y212F-GFP (which does not synthesize glycogen and is degraded by non-selective autophagy as cytosolic Pgk1-GFP) were equally well delivered to the vacuole and had similar levels of released GFP. Therefore, we concluded that glycogen autophagy is a non-selective process in K. phaffii yeast under nitrogen starvation conditions.

As one of toxic Volatile Organic Pollutant (TVOCs), formaldehyde has a toxic effect on microorganisms, and then inhibits the biochemical process of formaldehyde wastewater treatment. Therefore, the selective degradation of formaldehyde is of great significance to achieve formaldehyde wastewater high-efficiency and low-cost treatment. This study constructed a heterogeneous Fe-ZSM-5/H2O2 Fenton system for selective degradation to target compounds. By bonding Fe3+ onto the surface of ZSM-5 molecular sieve, Fe-ZSM-5 was prepared successfully. XRD, BET and FT-IR spectral studies shown the prepared Fe-ZSM-5 was mainly composed of micropores. The influences of different variables on formaldehyde selective heterogeneous Fenton degradation performance were studied. The 93.72% formaldehyde degradation and the 98.15% selectivity of formaldehyde compared with glucose had demonstrated in the optimized Fenton system after 360 min. Notably, the resultant selective Fenton oxidation system had a wide range of pH suitability from 3.0 to 10.0. Also, the Fe-ZSM-5 was used in 5 consecutive cycles, while the degradation efficiency of formaldehyde did not drop dramatically. Using reactive oxygen species scavengers, hydroxyl radical was the main active substance to degrade formaldehyde. Furthermore, the great degradation performance of this system to high concentration of formaldehyde was acquired, and the degrading efficiency was more than 95%.

Lipid nanoparticles (LNPs) are promising carriers for constructing drug delivery systems (DDSs) in disease treatments. Previous studies have suggested that lipid composition and biophysical properties of LNPs can significantly impact their interaction with cells and tissues, allowing for the development of suitable LNPs for precise drug delivery. Our previous study proposed the concept and facile preparation of reconstituted lipid nanoparticles (rLNPs), which not only have the advantages of traditional LNPs but also contain the lipids of mother cell/tissue. In this study, we have found that brain-derived rLNPs (B-rLNPs) can have much better accumulation to the ischemic area of the ischemic stroke (IS) model than liver-derived rLNPs (L-rLNPs). This homing effect hopefully makes rLNPs a useful tool for developing highly accessible devices with homologous targeting ability for precise drug delivery.

4-(thiazol-2-yldiazenyl)phenol (L₁) and 2-((4-hydroxyphenyl) diazenyl)-5-nitrophenol (L₂) based on azo phenol were synthesised and used as selective colorimetric sensor for CN^- and AcO⁻ ion in DMSO/H₂O-HEPES (v/v; 1:1, pH–7.3 ± 0.2) and showed good sensitivity with large red shifts and nanomolar detection limit for CN^- and AcO^- ion. The stoichiometry of L₁ with CN⁻/AcO⁻ ion was found to be 1:1 and L₂ with CN⁻/AcO⁻ ion was found to be 1:2. Binding constant for L₁+ CN⁻, L₁ + AcO⁻, L₂ + CN⁻ and L₂ + AcO⁻ were calculated by B-H plot as 1.6 × 10³, 8.0 × 10², 8.4 × 10³ and 1.7 × 10² respectively. L₂ showed high selectivity towards CN⁻ ion with low detection limit of 81 nM and large binding constant. In addition, ¹H NMR titration and DFT studies also supported the deprotonation mechanism of receptors in the presence of selective anions.

In this paper, a model of the hub covering the location-routing problem with simultaneous delivery and pickup should be designed in order to minimize the total costs, minimize the maximum vehicles travel time and minimize the amount of CO_2 gas emissions. Two-stage stochastic programming is used in this paper to control the uncertainty parameters of the problem. The mathematical model aims to decide the appropriate location of hubs and vehicle routing for simultaneous delivery and pickup of products. In this regard, the results obtained from the LP-Metric method show that there is a conflict between the objective functions, and with the reduction of the amount of CO_2 gas emissions and the reduction of the maximum vehicles travel time, the total costs have increased. On the other hand, by examining the economical factor, it was observed that by reducing this factor, the robustness factors are changed and the total costs of the network are reduced. MOIWO and MOALO were used to solve the problem in large scale, the result of which was the existence of a significant difference between the calculation time averages. Also, the efficiency of these methods was very high compared to the LP-Metric method and the maximum relative difference was less than 2.83%. The results of numerical examples show a higher efficiency of the MOALO than the MOIWO.

Purpose: Localization and mapping with LiDAR data is a fundamental building block for autonomous vehicles. Though LiDAR point clouds can often encode the scene depth more accurate and steadier compared with visual information, laser-based Simultaneous Localization And Mapping (SLAM) remains challengeable as the data is usually sparse, density variable and less discriminative. The purpose of this paper is to propose an accurate and reliable laser-based SLAM solution. Design/methodology/approach: The method starts with constructing voxel grids based on the 3D input point cloud. These voxels are then classified into three types to indicate different physical objects according to the spatial distribution of the points contained in each voxel. A global environment model with Partition of Unity (POU) implicit surface is maintained along the process and located voxels are merged into it from stage to stage, through scan-to-model matching implemented by Levenberg-Marquardt method. Findings: We find a laser-based SLAM method. The method uses POU implicit surface representation to build the model and is evaluated on the KITTI odometry benchmark without loop closure. Experimental results indicate that the method achieves accuracy comparable to the state-of-the-art methods. Originality/value: We propose a novel, low-drift SLAM method, which falls into a scan-to-model matching paradigm, operates on point clouds obtained from Velodyne HDL64. The method is of value to researchers developing SLAM systems for autonomous vehicles.

GDF5 gene is involved in the development of skeletal elements, synovial joint formation, tendons, ligaments, and cartilage. Several polymorphisms are present within the gene and two of them, rs143384 and 143383, have been reported as correlated with osteoarticular disease or muscle flexibility. The aim of this research is to verify if the worldwide distribution among human populations of rs143384 polymorphism has been shaped by selective pressure, or if it’s the result of random genetic drift events. Ninety-four individuals of both sexes, 18-28 years old, from Sardinia were analyzed. We observed the following genotype frequencies: 28.72% of homozygotes AA, 13.83% of homozygotes GG, and 57.45% of heterozygotes AG. Allele frequencies were 0.574 for allele A and 0.426 for alle G. Relationships between populations were verified by Multidimensional Scaling (MDS). Our data show: i) a clear heterogeneity within the African populations; ii) a strong differentiation between Africans and the other populations: iii) the Sardinian population is placed withing the European cluster. To reveal possible traces of selective pressure, Population Branch Statistic (PBS) was calculated; both SNPs rs143384 and 143383 have low PBS values, suggesting that there are no signals of selective pressure in those areas of the gene.

Chronic wasting disease is a fatal transmissible spongiform encephalopathy (TSE) of cervids caused by a misfolded variant of the normal cellular prion protein, and is closely related to sheep scrapie. Variations in a host’s prion gene, PRNP, and its primary protein structure, dramatically affect susceptibility to specific prion disorders, and breeding for PRNP variants that prevent scrapie infection has led to steep declines in the disease in North American and European sheep. While resistant alleles have been identified in cervids, a PRNP variant that completely prevents CWD has not yet been identified. Thus, control of the disease in farmed herds traditionally relies on quarantine and depopulation. In CWD-endemic areas, depopulation of private herds becomes challenging to justify, leading to opportunities to manage the disease in situ. In the present study, we developed a selective breeding program for farmed white-tailed deer in a CWD-endemic area, focused on reducing frequencies of highly susceptible PRNP variants and introducing animals with less-susceptible variants into historically high prevalence areas. We found that breeding followed predictable Mendelian inheritance, and early data support our project’s utility in reducing CWD prevalence. This project represents a novel approach to CWD management, with future efforts building on these findings.

Malassezia species are fastidious and slow-growing yeasts whose isolation from polymicrobial samples is hampered by fast-growing microorganisms. Malassezia selective culture media are needed because Malassezia are resistant to cycloheximide, but some fungi, including the chief human commensal Candida albicans resist to this compound. This study aimed to test whether the macrolide rapamycin could be used in combination with cycloheximide to develop a Malassezia-selective culture medium. Rapamycin susceptibility testing was performed via microdilution assays in modified Dixon against M. furfur and five Candida spp. The MIC was the lowest concentration producing 90% growth inhibition. Rapamycin medium ± cycloheximide 500 mg/L was also added to FastFung solid and yeast suspensions were inoculated and incubated for 72h. Rapamycin MICs against Candida spp. ranged from 0.5 to 2 mg/L, except for C. krusei whose MIC was >32 mg/L. M. furfur stains were rapamycin resistant. Rapamycin and cycloheximide supplementation of the FastFung medium effectively inhibited the growth of non-Malassezia yeast, including the cycloheximide-resistant C. albicans and C. tropicalis. Based on our findings, we recommend using this “MalaSelect” medium for Malassezia isolation and culture from polymicrobial samples.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

In standard construction of hyperrational numbers using ultra-power we assume that the ultralter is selective. It makes possible toassign real value to any nite hyperrational number. So, we can consider hyperrational numbers with selective ultralter as extension of traditional real numbers. Also proved the existence of strictly monotonic or stationary representing sequence for any hyperrational number.

Ecological and environmental damage caused by oil spillage has attracted great attention. Used cigarette filter (CF) has also caused negative environmental consequences. Converting CF to economical materials is a feasible way to address these problems. In this study, we demonstrate a simple method for production of a highly hydrophobic absorbent from CF. CF was modified by using different volume ratios of octadecyltrichlorosilane and methyltrimethoxysilane. When the volume ratio was 3:2, the modified CF had the high water contact angle of 155°. It could selectively and completely absorb silicone oil from an oil-water mixture and showed a good absorption capacity of 38.3 g/g. The absorbed oil was readily and rapidly recovered by simple mechanical squeezing, and it could be reused immediately without any additional treatments. The as-obtained superhydrophobic modified CF retained an absorption capacity of 80% for pump oil and 82% for silicone oil after 10 cycles. The modified CF showed good elasticity in the test of repeated use. The present study provides novel design of a functional material for development of hydrophobic absorbents from used CF via a facile method toward oil spillage cleanup as well as a new recycling method of CF to alleviate the environmental impact.

A study has been carried out on Ta and Nb recovery by liquid-liquid extraction process using 4-methylacetophenone (4-MAcPh) as organic phase. The 4-MAcPh was compared to methylisobutylketone (MIBK) with respect to extraction efficiencies (kD values) at different concentrations of H2SO4 in the aqueous phase. The results showed a similar extraction of Nb for both solvents. However, for Ta extraction efficiency is increased by a factor of 1.3 for 4-MAcPh. In addition, the MIBK solubilized completely after 6 mol L-1 of H2SO4 against only a loss of 0.14 to 4% for 4-MAcPh between 6 and 9 mol L-1 of H2SO4. The potential of 4-MAcPh has also been studied to selectively recover Ta from a model capacitor waste solution. The results showed a selectivity for Ta in the presence of impurities such as Fe, Ni, Mn. The 4-MAcPh also presents the advantage of having physicochemical properties adapted to its use in liquid-liquid extraction technologies such as mixer-settlers.

The important characteristic that could assist in autonomous navigation is the ability of a mobile robot to concurrently construct a map for an unknown environment and localize itself within the same environment. This computational problem is known as Simultaneous Localization and Mapping (SLAM). In literature, researchers have studied this approach extensively and have proposed a lot of improvement towards it. More so, we are experiencing a steady transition of this technology to industries. However, there are still setbacks limiting the full acceptance of this technology even though the research had been conducted over the last 30 years. Thus, to determine the problems facing SLAM, this paper conducted a review on various foundation and recent SLAM algorithms. Challenges and open issues alongside the research direction for this area were discussed. However, towards addressing the problem discussed, a novel SLAM technique will be proposed.

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and mitigate it for the affected citizenry. We propose enabling solutions to environmental odor issues by utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. We showed that the downwind odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we aim at summarizing three natural models of the rolling unmasking effect (RUE) and discuss them more systematically in the context of the proposed downwind environmental odor prioritization approach. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with downwind dilution. The extreme odor simplification-upon-dilution was demonstrated for two plant varieties, prairie verbena and Virginia pepperweed. Their downwind odor frontal boundaries were dominated by single, character-defining odorants; p-cresol-dominated ‘barnyard’ odor, and benzyl mercaptan-dominated ‘burnt match’ odor, respectively. The P.T. porcupine downwind odor frontal boundary was dominated by two potent, character-defining odorants: (1) ‘onion’/‘body odor’ odorant #1 and (2) ‘onion’/‘grilled’ odorant #2. In contrast with their downwind boundary simplicities, each odor source presented considerable compositional complexity and composite character difference near the source. The proposed RUE approach’s ultimate significance is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using the analytical only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of compounds being emitted by the source.

The selectivity in selective autophagy pathways is achieved via the selective autophagy receptors (SARs) – proteins that bind a ligand on the substrate to be degraded and the Atg8-family protein on the growing autophagic membrane, phagophore, effectively bridging them. In mammals, the most common ligand of SARs is ubiquitin, a small protein modifier that tags substrates for their preferential degradation by autophagy. Consequently, the most common SARs are the ubiquitin-binding SARs, such as SQSTM1/p62 (sequestosome 1). Surprisingly, there is only one SAR of this type in yeast – Cue5, which acts as a receptor for aggrephagy and proteaphagy – pathways that remove the ubiquitinated protein aggregates and proteasomes, respectively. However, recent studies described the ubiquitin-dependent autophagic pathways that do not require Cue5, e.g. stationary phase lipophagy for intracellular lipid droplets and nitrogen starvation-induced mitophagy for mitochondria. What is the role of ubiquitin in these pathways? Here, we propose that the ubiquitinated lipid droplets and mitochondria are recognized by the alternative ubiquitin-binding SARs. Our analysis identifies the proteins that could potentially fulfill this role in yeast. We think that matching of the ubiquitin-dependent (but Cue5-independent) autophagic pathways with the ubiquitin-and-Atg8-binding proteins enlisted here might uncover the novel ubiquitin-binding SARs in yeast.

Film cooling technology is of great significance to enhance the performance of aero-engines and extend service life. With the increasing requirements for film cooling efficiency, researchers and engineers have carried out a lot of work on the precision and digital measurement of cooling holes. Based on the above, this paper outlines the importance and principles of film cooling technology, reviews the evolution of cooling holes. Also, this paper details the traditional measurement methods of the cooling hole used in current engineering scenarios with their limitations and categorizes digital measurement methods into five main types, including probing measurement technology, optical measurement technology, infrared imaging technology, computer tomography(CT) scanning technology, and composite measurement technology. The five types of methods and integrated automated measurement platforms are also analyzed. Finally, through a generalize and analysis of cooling hole measurement methods, this paper points out technical challenges and future trends, providing a reference and guidance for forward researches.

Porcine sapovirus (PoSaV) is a significant pathogen causing diarrhea with high morbidity and mortality rates. Given its zoonotic characteristics, this study conducts a comprehensive genetic evolutionary analysis of PoSaV. Results confirmed PoSaV as the primary RNA virus in piglet feces (27.54%). Phylogenetic analysis identifies the prevalent PoSaV strain SHCM/Mega2023 in the GIII genogroup, involving a recombinant event with MK962338 and KT922089. The time tree revealed that the GIII genogroup exhibits the widest divergence time span, indicating a high likelihood of viral recombination. Further selective pressure calculations demonstrate that PoSaV was under purifying selection (dN/dS < 1), with seven positively selected sites in VP1 protein which might be related to the antigencity. In conclusion, this study presents a novel genomic evolution of PoSaV, offering valuable insights into antigenicity and vaccine research.

Selective laser sintering (SLS) has drawn attention for the fabrication of three-dimensional oral dosage forms due to the plurality of drug formulations that can be processed. The aim of this work was to employ SLS with a CO2 laser for the manufacturing of carvedilol personalised dos-age forms of various strengths. Carvedilol (CVD) and vinylpyrrolidone-vinyl acetate copolymer (Kollidon VA64) blends of various ratios were sintered to produce CVD tablets of 3.125, 6.25 and 12.5 mg. The tuning of the SLS processing parameter laser intensity, improved printability and impacted the tablet hardness, friability, CVD dissolution rate, and the total amount of drug re-leased. Physicochemical characterization showed the presence of CVD in the amorphous state. X-ray micro-CT analysis demonstrated that the applied CO2 intensity affected the total tablet po-rosity, which was reduced with increased laser intensity. The study demonstrated that SLS is a suitable technology for the development of personalised medicines that meet the required specifications and patient needs.

Delayed atomic layer deposition (ALD) of ZnO, i.e., area selective (AS)-ALD, was successfully achieved on silicon wafers (Si/SiO2) terminated with tris(dimethylamino)methylsilane (TDMAMS). This resist molecule was deposited in a home-built, near atmospheric pressure, flow-through , gas-phase reactor. TDMAMS has been shown to react with Si/SiO2 in a single cycle/reaction and to drastically reduce the number of silanols that remain at the surface. ZnO was deposited in a commercial ALD system using dimethylzinc (DMZ) as the zinc precursor and H2O as the coreactant. Deposition of TDMAMS was confirmed by spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), and wetting. ALD of ZnO, including its selectivity on TDMAMS – terminated Si/SiO2 (Si/SiO2/TDMAMS), was confirmed by in situ ellipsometry, ex situ SE, XPS, and/or high sensitivity – low energy ion scattering (HS-LEIS). The thermal stability of the TDMAMS resist layer, which is an important parameter for AS-ALD, was investigated by heating Si/SiO2/TDMAMS in air and nitrogen at 330 ºC. ALD of ZnO takes place more readily on Si/SiO2/TDMAMS heated in the air than in N2, suggesting greater damage to the surface heated in the air. To better understand the in situ ALD of ZnO, the data were also plotted as the normalized growth per cycle and to show the selectivity. Even one, short pulse of TDMAMS effectively passivates Si/SiO2. TDMAMS can be an effective small molecule inhibitor of ALD of ZnO on Si/SiO2 surfaces.

The effects of build orientation and heat treatment on the crack growth behavior of 316L stainless steel (SS) fabricated via a selective laser melting (SLM) additive manufacturing process were investigated. Significant growth of available research results of additively manufactured metallic parts still needs to be improved. The most important issue connected with properties after additive manufacturing is properties high anisotropy, especially from the fatigue point of view. The research included crack growth behavior of additively manufactured 316L in comparison to conventionally made reference material. Both groups of samples were obtained using precipitation heat treatment. Different build orientation in additively manufactured samples and rolling direction in reference samples were taken into account as well. Precipitation heat treatment of additively manufactured parts allowed to reach similar microstructure and tensile properties to elements conventionally made. The heat treatment positively affected fatigue properties. Additionally, precipitation heat treatment of additively manufactured elements significantly affected the reduction of fatigue cracking velocity and changed the fatigue cracking mechanism.

Applied electrostatic engineering can be used to construct greenhouses that prevent entry of insect pests. Two types of electric field screen were used to exclude pests from the greenhouse: single- and double-charged dipolar electric field screens (S- and D-screen, respectively). The S-screen consisted of iron insulated conductor wires (ICWs) arrayed in parallel (ICW-layer), a grounded metal net on either side of the ICW-layer, and a direct current voltage generator. S-screens were attached to the side windows of the greenhouse to repel whiteflies (Bemisia tabaci) that approached the nets. The D-screen was installed in a small anteroom at the greenhouse entrance to capture whiteflies entering through it. The ICW-layers of the D-screen were oppositely charged with equal voltages and arrayed alternately, and an insulator board or grounded metal net was placed on one side of the ICW-layer. The ICW-layers captured whiteflies entering the electric field of the double-charged dipolar electric field. Three screens equipped with yellow or gray boards or a grounded metal net were installed in the anteroom based on the airflow inside the room, as most whiteflies were brought in by air when the door was opened. Two D-screens with boards were useful for directing the airflow toward the wall with the netted D-screen. This screen eliminated the insects and the pest-free air was circulated inside the greenhouse. The D-screen with the yellow board attracted the whiteflies and was effective for trapping them when there was no wind. Our method kept the greenhouse pest-free throughout the entire period of tomato (Solanum lycopersicum) cultivation.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

Unmanned Underwater Vehicles (UUVs) are pivotal in ocean exploration, research, and various industrial activities such as marine mining and offshore engineering. However, traditional methods of navigating these vehicles face significant challenges, mainly due to the inefficacy of electromagnetic waves in water, leading to signal loss. To address these limitations, researchers are increasingly turned learning, an artificial intelligence technique capable of learning from data-enhancing underwater navigation, mainly through visual Simultaneous Localization and Mapping (SLAM). This paper explores integrating deep learning methodologies and sensor technologies to revolutionize underwater navigation for UUVs. Proprioceptive sensors, along with exteroceptive sensors, are crucial in accurately measuring and comprehending the underwater environment. Additionally, the paper provides detailed insights into the processes of underwater SLAM, camera-based underwater positioning systems, sonar systems for underwater navigation, and the utilization of Lidar in underwater navigation. Furthermore, it delves into applying deep learning techniques in underwater SLAM, offering a comprehensive understanding of the innovative processes driving advancements in underwater vehicle navigation. By leveraging these advancements, this research aims to improve underwater navigation systems' precision, reliability, and adaptability, thereby unlocking new frontiers in ocean exploration and industrial applications for UUVs.

Sequential properties can violate Bell-type inequalities without direct influence on each other, but only if detected in pairs. This is demonstrated below with theoretical arguments, and with a straightforward toy model. Rotating arrows can have transient qualities that produce maximal Bell violations with predetermined values. Any non-signaling phenomenon (classical, or non-classical) can also be interpreted as local.

By the end of 2023, biowaste must be completely separated or recycled at source based on the EU legislation. Separate biowaste collection and valorisation towards biofuels could play an essential role in the biobased circular economy. In this context, the principal goal of this paper was to demonstrate in pilot scale the technological solution of bioethanol production via the utilisation of urban source-separated biowaste within the city context of Athens, Greece. More specifically, the main aim was the demonstration of a pilot system in continuous operation (over 10 operating cycles) with real feedstock – wet separately collected biowaste. From the 11 pilot trials performed with wet feedstock, the mean starch and cellulose degradation of the pilot trials amounted up to 80.69±16.27% and 79.41±10.37% respectively, while the bioethanol yield was 74.05±6.82%. The latter was comparable to that of more intensive pretreatment methods. Homogenization and shredding that was applied in this study, stand as promising and cost-effective pretreatment methods for bioethanol production from wet feedstock. Further research is needed to optimize conditions and evaluate scalability. Nevertheless, pilot scale testing is a crucial step in the development and deployment of this technology since it serves as a bridge between laboratory research and full-scale implementation, offering a practical and controlled environment to validate and optimize the technology while minimizing risks and uncertainties.

Analytics have become increasingly popular among sports in recent years, providing valuable information regarding physical and mental health. Many athletes have found that analytics during training can help to improve their performance, reduce the risk of injury, and enhance their overall well-being. This paper aims to improve the results of handball players by applying a method for measuring the influence of different trials on aggregate performance calculated per each athlete in order to qualify for the Olympic Games. By separating the isolated action of each trial, the result is an additional influence caused by the interaction of factors or the simultaneous action. That might explain why the neuromuscular feedback loop is utterly necessary to perform handball motor actions. Further on, the ML analysis can help identify areas for improvement, optimize training programs, and enhance overall team performance.

The identification of cancer predisposition syndromes (CPSs) plays a crucial role in understanding the etiology of pediatric cancers. CPSs are genetic mutations that increase the risk of developing cancer at an earlier age compared to the risk for the general population. This article aims to provide a comprehensive analysis of three unique cases involving pediatric patients with CPS who were diagnosed with multiple simultaneous or metachronous cancers. The first case involves a child with embryonal rhabdomyosarcoma, nephroblastoma, glioma, and subsequent medulloblastoma. Genetic analysis identified two pathogenic variants in the BRCA2 gene. The second case involves a child with alveolar rhabdomyosarcoma, Xanthogranuloma Juvenile, gliomas, and subsequent JMML/MDS/MPS. A pathogenic variant in the NF1 gene was identified. The third case involves a child with pleuropulmonary blastoma and pediatric cystic nephroma/nefroblastoma in whom a pathogenic variant in the DICER1 gene was identified. Multiple simultaneous and metachronous cancers in pediatric patients with CPSs are a rare but significant phenomenon. Comprehensive analysis and genetic testing play crucial roles in understanding the underlying mechanisms and guiding treatment strategies for these unique cases. Early detection and targeted interventions are crucial for improving outcomes in these individuals.

Hydrodechlorination reaction of 3-(benzo-1,3-dioxol-5-yl)-3-chloro-2-methylacrylaldehyde in the presence of different low metal content heterogeneous mono- or bi-metallic catalysts was tested for the synthesis of the fragrance Helional® (3-[3,4-methylendioxyphenyl]-2-methyl-propionaldehyde). In particular, mono Pd/Al2O3, Rh/Al2O3 or bi-metallic Pd-Cu/Al2O3, Rh-Cu/Al2O3 catalysts were tested in different reaction conditions from which it emerged that mono-Rh/Al2O3 was the best performing catalyst allowing to achieve 100% substrate conversion and 99% selectivity towards Helional® in 24h at 80°C, p(H2) 1.0 MPa in the presence of a base. To establish correlations between atomic structure and catalytic activity, catalysts were characterized by Cu, Rh and Pd K-edge XANES, EXAFS analysis. These characterizations allowed to verify that the formation of Pd-Cu alloys and the presence of Cu oxide/hydroxide species on the surface of the Al2O3 support, are responsible for the very low catalytic efficiency of bimetallic species tested.

Advanced paternal age increases the risk of transmitting de novo germline mutations, particularly missense mutations activating the receptor tyrosine kinase (RTK) signaling pathway, exemplified by the FGFR3 mutation linked to achondroplasia (ACH). This risk is attributed to the expansion of spermatogonial stem cells carrying the mutation, forming sub-clonal clusters in the ageing testis, thereby increasing the frequency of mutant sperm and the number of affected offspring from older fathers. While prior studies proposed a correlation between sub-clonal cluster expansion in the testis and elevated mutant sperm production in older donors, limited data exist on the universality of this phenomenon. Our study addresses this gap by examining the testis expansion patterns, as well as increases of mutations in sperm for two FGFR3 variants: c.1138G>A (p.G380R) and c.1948A>G (p.K650E)- associated with ACH or thanatophoric dysplasia (TDII), respectively. Unlike the ACH mutation, which showed sub-clonal expansion events in an aged testis and a significant increase of mutant sperm with the donor’s age, the TDII mutation formed sub-clonal clusters, but exhibited reduced transmission into sperm and no significant age-related increase. The mechanism behind this divergence remains unclear, suggesting potential pleiotropic effects of aberrant RTK signaling in the male germline, possibly hindering differentiation requiring meiosis. This study provides further insights into transmission risks of micro-mosaics associated with advanced paternal age in the male germline.

Biodiesel is one of the most popular biofuels as it is a promising substitute of the conventional diesel fuel, but for now it cannot be used as a stand-alone fuel due to its low oxidative stability. For this reason, the last years there have been efforts for its upgrading through the partial hydrogenation of the fatty acid methyl esters (FAMEs) that biodiesel consists of. This procedure succeeds in resolving the problem of low oxidative stability, but in some cases a new problem arises as the non-selective hydrogenation is deteriorating the fuel’s cold flow properties, which are crucial for its operation without damaging the vehicle’s engine. More specifically, the problem of deteriorated cold flow properties is caused by the formation of trans-monounsaturated FAMEs and fully saturated FAMEs while the hydrogenation reaction is taking place. The hydrogenated biodiesels are preferred to contain more cis-monounsaturated FAMEs, because these are considered to have the best combination between high oxidative stability and good cold flow properties. As a result, various systems and methods have been tested in order to achieve a selective partial hydrogenation of biodiesel’s FAMEs. In this review article, the catalytic systems and methods that stood out in various researches are presented and the factors that lead to the best possible outcome are investigated and discussed.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

In this research, a novel collector cetyl trimethyl ammonium chloride (CTAC) was used to separate hematite from quartz via reverse flotation for the first time. Micro-flotation tests showed that CTAC had a strong ability to selectively collect quartz and a separation of hematite from quartz could be accomplished with a concentration of 0.00263 mmol/L CTAC. Zeta-potential measurements indicated that the positive CTAC+ species could selectively increase the surface potential of quartz, but it had rather a weak effect on the hematite surface. X-ray photoelectron spectroscopy (XPS) detection indicated that CTAC had a stronger binding affinity to oxygen sites on the surface of quartz than that of hematite, resulting in a large amount of CTAC predominantly adsorbed on quartz rather than hematite.

The concept of targeted drug delivery can be described in terms of the drug’s ability to mimic the other biological objects’ property to localize to target cells or tissues. For example, drug delivery systems based on red blood cells or mimicking some of their useful features, such as long circulation in stealth mode, have been known for decades. On the contrary, therapeutic strategies based on macrophages have gained very limited attention until recently. Here we review two biomimetic strategies associated with macrophages, that can be used to develop new therapeutic modalities: First, the mimicry of certain types of macrophages (i.e., the use of macrophages, including tumor-associated, or macrophage-like particles as a carrier for targeted delivery of therapeutic agents); and Second, the mimicry of ligands, naturally absorbed by macrophages (i.e., the use of therapeutic agents specifically targeted at macrophages). We discuss potential applications of biomimetic systems involving macrophages for the new advancements in treatment of infections, inflammatory diseases, and cancer.

Firocoxib is a non-steroidal anti-inflammatory drug specifically formulated for veterinary medicine and selectively acts on inhibiting the cyclooxygenase 2 enzyme(COX-2). This study aimed to evaluate the possible adverse effects of administering oral therapeutic firocoxib on gastric mucosa, hematological parameters, coagulation cascade, and hepatic and renal biochemistry in healthy horses. Nine clinically healthy Arabian horses, approximately nine years old, received 0.1mg/kg of oral firocoxib for 14 days. Before beginning treatment, a gastroscopic examination was conducted, and venous blood samples were obtained for laboratory tests on D0. Follow-up blood samples and gastroscopic examinations were taken on D7 and D14 after starting treatment and one week after completing treatment on D21. No changes were found in the gastroscopic and hematological tests. Additionally, coagulation and serum biochemistry levels remain between normal values for this particular species. However, the increased activated partial thromboplastin time (aPTT) and prothrombin time (PT) indicate reduced blood coagulation capacity, which contradicts the expected effect of treatment with selective COX-2 inhibitors, as these drugs theoretically promote coagulation. Administering Firocoxib to horses is safe as it does not cause any significant adverse reactions. Therefore, it is a suitable option for managing inflammatory conditions in these animals.

Small molecule modulators of neurotensin receptor 1 (NTSR1), a class A G protein-coupled receptor (GPCR), has been emerging as promising therapeutics for psychiatric disorders and cancer. Interestingly, a chemical group substitution of NTSR1 modulators can launch different downstream regulation, highlighting the significance of deciphering the internal fine-tuning mechanism. Here, we conducted synergistic application of Gaussian accelerated molecular dynamics simulation, conventional molecular dynamics simulation, and Markov state models (MSM) to investigate the underpinning mechanism of ‘driver chemical groups’ of modulators triggering inverse signaling. The result indicated that the flexibility of leucine moiety in NTSR1 agonists contributes to the inward displacement of TM7 through a loosely coupled allosteric pathway, while the rigidity of adamantane moiety in NTSR1 antagonists leads to unfavorable downward transduction of agonistic signaling. Furthermore, we found that R3226.54, Y3196.51, F3537.42, R1483.32, S3567.45 and S3577.46 may play a key role in inducing the activation of NTSR1. Together, our findings not only highlight the ingenious signal transduction within class A GPCRs, but also lay a foundation for the development of targeted drugs harboring different regulatory function of NTSR1.

The study presents the synthesis and characterization of dual-layer sulfonated polyphenylenesulfone (SPPSu) nanocomposite hollow fiber nanofiltration membranes incorporating titanium dioxide (TiO2) nanoparticles using the phase inversion technique. The newly developed membranes were systematically characterized using advanced tools and methods to evaluate their properties and performance. The study focused on investigating the effects of TiO2 addition in the SPPSu inner layer on pure water permeability, and salt rejection. The nanocomposite hollow fiber nanofiltration membranes exhibited a significant enhancement in pure water permeability, with a three-fold increase compared to the pristine membranes, achieving a flux of 5.4 L/m2h.bar. The addition of TiO2 also led to an improvement in the mechanical properties of the membranes, as evidenced by the increase in the expected tensile strength from 2.4 to 3.9 MPa. To evaluate the salt rejection performance, rejection tests were conducted using a laboratory-scale filtration setup in recycle mode. Aqueous solutions containing different divalent ions, specifically magnesium sulfate (Mg2SO4) and sodium sulfate (Na2SO4) at a concentration of 500 ppm, were used as the feed solution. The modified dual-layer hollow fiber nanocomposite membranes exhibited a maximal rejection of 95% for Mg2SO4, demonstrating their effective separation capabilities for divalent ions. The findings of this study highlight the successful synthesis and characterization of dual-layer SPPSu nanocomposite hollow fiber nanofiltration membranes incorporating TiO2 nanoparticles. The incorporation of TiO2 resulted in improved pure water flux, mechanical strength, and salt rejection performance. These enhanced properties make the developed nanocomposite membranes promising candidates for applications in nanofiltration processes, particularly for the selective separation of divalent ions from aqueous solutions.

Molluscan aquaculture is a major contributor to global seafood production, but is hampered by infectious disease outbreaks which can cause serious economic losses. Selective breeding has been widely used to improve disease resistance in major agricultural and aquaculture species, and has clear potential in molluscs, albeit its commercial application remains at a formative stage. Advances in genomic technologies, especially development of cost-efficient genomic selection, have potential to accelerate genetic improvement. However, tailored approaches are required due to the distinctive reproductive and lifecycle characteristics of molluscan species. Transgenesis and genome editing, in particular CRISPR/Cas systems, have been successfully trialled in molluscs, and may further understanding and improvement of genetic resistance to disease through targeted changes to the host genome. Whole organism genome editing is achievable on a much greater scale compared to other farmed species, making genome-wide CRISPR screening approaches plausible. This review discusses the current state and future potential of selective breeding, genomic tools, and genome editing approaches to understand and improve host resistance to infectious disease in molluscs.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

We have studied on the stress measurement by making use of salivary nitrate, which can be a candidate of stress markers, with ion-selective field-effect transistors (ISFETs). ISFETs are suitable for on-site single-drop analysis of salivary nitrate within 10 seconds. However, when ISFETs are used for salivary nitrate, ISFETs have a problem which is called the initial drift. The initial drift makes it difficult for determination of an accurate nitrate monitoring. Thus, the purpose of this study is to suppress an initial drift and to search for new easy polymer to possess more performance of sensor responses than conventional matrix membrane such as PVC. In this research, we investigated ISFETs using specific matrix membrane for example, KP-13, Pellethane^® and P7281-PU. The initial drift was evaluated from the fluctuation of the response values generated by ISFETs which are immersed in saliva or aqueous solution. As a result, P7281-PU showed its suppression effect for the initial drift in the whole saliva and various solutions. Furthermore, the cause of drift may be H⁺ diffusion, and drift suppression effect of P7281-PU may be affected by urethane bond capturing H⁺ in ion-selective membrane. This result suggests a continuous nitrate monitoring and development of wearable sensors.

Using nanoindentation under various strain rates, the mechanical properties of a selective laser melted (SLM) SKD61 at the 800 mm/s scan speed was investigated and compared to SLM H13. No obvious pile-up due to the ratio of the residual depth (h_f) and the maximum depth (h_max) being lower than 0.7 and no cracking were observed on any of the indenter surfaces. The nanoindentation strain-rate sensitivity (m) of SLM SKD61 was found to be 0.034, with hardness increasing from 8.65 GPa to 9.93 GPa as the strain rate increased between 0.002 s⁻¹ and 0.1 s⁻¹. At the same scan speed, the m value of SLM H13 (m = 0.028) was lower than that of SLM SKD61, indicating that the mechanical behavior of SLM SKD61 was more critically affected by the strain rate compared to SLM H13. SLM processing for SKD61therefore shows higher potential for advanced tool design than for H13.

Research Highlights: The study determined that selective thinning causes different responses, the initial size of the tree released is an influential factor in the growth of species. The temporality of climate and physiological conditions of each species are influential in the growth. It is evident that the defoliation of certain species is an important factor that limits the growth of the species causing thinning to have a negative response. Background and Objectives: The objective is to analyze the behavior of nine timber species, respective to diametric growth after their liberation. This research aims to answer the following questions: (i) How do the selected tree species react to the liberation? (ii) Can the productivity of the trees (diametric growth) be enhanced by liberation? (iii) Are there other factors that influence the diametric growth of the released trees? Materials and Methods: The study was executed in the “Reserva Biológica San Francisco” were 488 trees were monitored, including nine timber species. Therefore, 197 trees were released (removal of competitors) and 251 trees served as reference. To check whether the initial DBH or other factors, like the selective thinning or climate conditions, determine the diameter growth a linear mixed model GLMM was applied. To adjust the linear mixed model a one-way Anova test was executed. Results: Timber species responded differently to the thinning in comparing to reference trees. Therefore, the species analyzed were separated into three groups (positive, negative, and no response to liberation). Conclusions: Liberation potentiates the growth of certain timber species that do not defoliate and considered semi-tolerant to shade. Precipitation and temperature affect all species, but in the defoliate species, it would not be convenient to release them or at least the evidence of these first three years does not show clear differences with control trees. Increase in trees released are higher in trees of the first two diametric classes in all species, this means that larger trees (i.e., older) release does not affect them in a positive way so release should occur in the youngest trees.

A study of photovoltaic solar window technologies is reported, focusing on their structural features, functional materials, system development, and suitability for use in practical field applications, e.g. public infrastructures and agricultural installations. Energy generation performance characteristics are summarized and compared to theory-limit predictions. Working examples of pilot-trial solar window-based installations are described. We also report on achieving electric power outputs of about 25 W_p/m² from clear and transparent large-area glass-based solar windows.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Statistical analysis of mechanical properties of thin-walled samples (~500 microns) obtained by selective laser melting from AlSi10Mg material and subjected to heat treatment for 1 hour at temperatures from 260 °C to 440 °C (step of aging temperature change 30 °C) has shown that the maximum strain hardening in the stretching diagram section from yield strength to tensile strength is achieved at the heat treatment temperature equal to 290 °C. At carrying out of correlation analysis statistically significant positive correlation between deformation corresponding to yield strength and the sum of heights of the largest protrusions and depths of the largest depressions of the surface roughness profile within the basic length of the sample (Rz) and the full height of the surface roughness profile (Rmax) was established. It was found that the reason for the correlation is the presence of cohesive states between the extreme values of the surface roughness profile that persist along the entire length of the specimen.

RNA interference (RNAi) using small interfering RNAs (siRNAs) is a powerful tool to target any protein of interest and is becoming more implementable for in vivo applications due to recent developments in RNA delivery systems. To exploit RNAi for cancer treatment, it is expedient to increase its selectivity by e.g. a prodrug approach to activate the siRNAs upon external triggering, e.g. by using light. Red light is especially well suitable for in vivo applications due to its low toxicity and higher tissue penetration. Known molecular (not nanoparticle based) red light activatable siRNA prodrugs rely on singlet oxygen (1O2) mediated chemistry. 1O2 is highly cytotoxic. Additionally one of the side products in the activation of the known siRNA prodrugs is anthraquinone, which is also toxic. We here report on an improved red light activatable siRNA prodrug, which do not require 1O2 for their activation. The 5’ terminus of its antisense strand is protected with an electron-rich azobenzene promoiety. It gets reduced and cleaved upon red light exposure in the presence of Sn(IV)(pyropheophorbide a)dichloride acting as a catalyst and ascorbate required as a bulk reducing agent producing active siRNAs.

The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC crystal structure was additively manufactured with a selective laser melting (SLM) process starting from mechanically alloyed powders. The as produced alloy shows finenitride and  phase pre-cipitates, which are Cr-rich and stable up to about 900 K. The precipitates increase in number and dimensions after long-period annealing at 900-1300 K, with a change in the HEA mechanical properties. Higher aging temperatures in furnace, above 1300 K, turn the alloy in a single FCC structure, with disappearance of the nitrate and  phase precipitates inside the grains and at the grain boundaries, but with still a presence of a finer Cr-rich nitride precipitation phase. These re-sults suggest that the as-produced HEA is a supersatured solid solution at low and intermediate temperature with nitrides and  nanostructures.

The mechanical properties and stability of hydrophobic surface structures prepared by traditional methods are still the main technical bottlenecks restricting the broad application of hydrophobic systems on workpiece surfaces. In this contribution, we propose a technique called selective laser shock peening (SLSP) to enable large-scale high efficient, low-cost manufacturing of hydrophobic metal surfaces with enhanced mechanical properties for durable applications. Using the method of experimental investigation combined with numerical calculation, the hydrophobic properties, mechanical properties, and tribological properties of the samples prepared under SLSP, all-laser shock peening (ALSP), and non-laser shock peening (NLSP) are studied. The SLSP process could prepare a 3D gradient structure material with surface structures, a two-phase (strong phase, soft phase) distribution on the surface, and a multi-level gradient distribution in the thickness direction. Compared with the 2D gradient structure prepared by the traditional process, 3D gradient structures by SLSP have more significant advantages in improving the wetting behavior and the mechanical properties of the material, which proves SLSP to be a novel method to fabricate functional metal surface structures, with highly high engineering application value.

The current study evaluates the selection signals in the evolution of mitochondrial DNA of voles, subfamily Arvicolinae, during the colonization of subterranean environments. The comparative sequence analysis of mitochondrial protein-coding genes of eight subterranean vole species (Prometheomys schaposchnikowi, three species of the genus Ellobius: E. talpinus, E. fuscocapillus and E. lutescens, two species of the genus Terricola: T. subterraneus and T. daghestanicus, Lasiopodomys mandarinus and Hyperacrius fertilis) and their closest aboveground relatives using codon-substitution models was applied. The highest number of selection signatures was detected in genes ATP8 and CYTB. The relaxation of selection was observed in most mtDNA protein-coding genes. In mole voles (genus Ellobius) the signatures of adaptive evolution of mitochondrial genes related to subterranean niche were most pronounced. The number of selection signatures was found to be independent of the evolutionary age of the lineage but fits the degree of specialization to the subterranean niche. The common trends of selective pressures were observed among the evolutionary ancient and highly specialized subterranean rodent families and phylogenetically young lineages of voles. It suggests that the signatures of adaptations in individual mitochondrial protein-coding genes associated with the colonization of the subterranean niche may appear within a rather short evolutionary timespan.

The corrosion morphology in grade 2205 duplex stainless steel wire has been studied to understand the nature of pitting and the causes of the ferrite phase's selective corrosion in acidic NaCl solution. It is shown that the corrosion mechanism is always pitting, which either manifests lacy cover perforation or densely-arrayed selective cavities developing on the ferrite phase. Pits with a lacy metal cover form in concentrated chloride solutions, whereas the ferrite phase's selective corrosion develops in diluted electrolytes, showing dependency on the chloride-ion concentration. The pit perforation is probabilistic and occurs on both austenite and ferrite grains. The lacy metal covers collapse in concentrated solutions but remain intact in diluted electrolytes. The collapse of the lacy metal cover happens due to hydrogen embrittlement. Pit evolution is deterministic and occurs selectively in the ferrite phase in light chloride solutions.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Gender differences have been documented in the prevalence of psychological symptoms. Tic disorders and ASD are more common in male clinical samples, while selective mutism and trichotillomania are more common in female clinical samples. In a review of 84 published case studies of Japanese children, this study explores gender differences in the prevalence of four categories of symptoms and expressions made in therapy for tics, selective mutism, trichotillomania, and autism spectrum disorder (ASD). Case studies were evaluated using both qualitative coding and statistical analysis. The findings were mostly consistent with epidemiological surveys and empirical research on adults. The gender differences in symptom prevalence and their expression can be summarized as differences in more direct aggression for boys versus indirect aggression for girls. The objective and progress in the therapy are to control impulsive energy for boys and to express energy for girls.

Abstract: The quantitative analysis of the chromatographic behavior of basic compounds was performed in silico. The liquid chromatography (LC) data measured with pentyl-, hexenyl-, and octyl-bonded silica gels were analyzed in silico employing model phases. The main retention force was the van der Waals (VW) interaction, and the main desorption force was an electrostatic (ES) interaction. The contribution of hydrogen bonding (HB) was weak compared to that for acidic compounds. The quantitative explanation was achieved utilizing the calculated VW, HB, and ES energy values obtained from a molecular mechanics program. The electron localization was observed at the molecular interaction-site calculated MOPAC program. This fundamental approach was like that of explaining chemical reactions. The difference was electron localization in chromatography or electron transfer in a chemical reaction.

This paper studies a multihop amplify-and-forward (AF) simultaneous wireless information and power transfer (SWIPT) relaying system. Each relaying node harvests energy using power splitting (PS) scheme from a part of its received signal to amplify and forward the rest the received signal to the next relay. Based on this system model and signal flow, we derived and solved the convex energy minimization problem with optimal PS ratio. The influence of processing cost was then investigated for the AF-SWIPT system with the decode-and-forward SWIPT as benchmark, where AF-SWIPT was found to be superior.

Single particle analysis with cryogenic electron microscopy (cryo-EM) can determine high resolution structures of macromolecular assemblies. To reconstruct final three-dimension(3D) density map, a reliable initial model is essential and ab-initio reconstruction usually can avoid model bias. The grand challenge for ab-initio reconstruction is to alignment two-dimension(2D) low signal-to-noise ratio(SNR) of particle images with random and unknown parameters. Here we formulate a fast ab initio reconstruction method(named AlignFM) based on Fourier Mellin transform and particle-swarm intelligence optimization(PSO) algorithm. It enables simultaneous 2D alignment and 3D refinement, which can fast generate a reliable 3D map. After experiments on several real datasets. AlignFM shows high performance on fast ab initio reconstruction with a small amount of data.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

We introduce a novel method for fabricating perovskite solar modules using selective spin-coating on various Au/ITO patterned substrates. These patterns were engineered for twofold purposes: (1) to enhance selectivity of monolayers primarily self-assembling on the Au electrode, and (2) to enable seamless interconnection between cells through direct contact of the top electrode and the hydrophobic Au connection electrode. Utilizing SAMs-treated Au/ITO, we achieved sequential selective deposition of the electron transport layer (ETL) and the perovskite layer on the hydrophilic amino-terminated ITO, while the hole transport layer (HTL) was deposited on the hydrophobic CH3-terminated Au connection electrodes. Importantly, our approach had negligible impact on the series resistance of the solar cells, as evidenced by the measured specific contact resistivity of the multilayers. A significant outcome was the production of a 6-cell series-connected solar module with a notable average PCE of 8.32%, providing a viable alternative to the conventional laser scribing technique.

Breast cancer is the most common cancer among women worldwide, and estrogen receptor-positive (ER+) breast cancer accounts for a significant proportion of cases. While various treatments are available, endocrine therapies are often the first-line treatment for this type of breast cancer. However, the development of drug resistance poses a significant challenge in managing this disease. ESR1 mutations have been identified as a common mechanism of endocrine therapy resistance in ER+ breast cancer. The first-generation selective estrogen receptor degrader (SERD) fulvestrant has shown some activity against ESR1 mutant tumors. However, due to its poor bioavailability and need for intramuscular injection, it may not be the optimal therapy for patients. Second-generation SERDs have been developed to overcome these limitations. These newer drugs have improved oral bioavailability and pharmacokinetics, making them more convenient and effective for patients. Several oral SERDs are now in phase III trials for early and advanced ER+ breast cancer. This review summarizes the background of oral SERD development, the current status, and future perspectives.

In this study, the effect of increasing exposure time on microstructures, defectiveness, mechanical properties and corrosion behavior of selective laser melted sample Al-Si10-Mg powder have been investigated. The sample were processed at the same power (375 W) and scan speed (2000 mm/s) but with increasing exposure time. Exposure time equal to 40, 50 and 60 µs was applied. The features of the analyzed samples show that with increasing exposure time a better efficiency of the heat input has been obtained with larger size of melting pool and Si particles and lower defectiveness. Moreover, being the coarser microstructure associated a to lower level of voids, the average hardness is similar for the analyzed samples. The potentiodynamic curves of the samples show that the voids occurrence is more significant with respect to the scale of micro-structure on corrosion behavior being the sample processed at the highest exposure time the more resistant to corrosion. The experimental techniques used in the present study were Optical microscope, Sem microscope, Hardness and X-Ray Computed Tomography.

Enterocins are bacteriocins synthesized by Enterococcus strains that show an interesting antimi-crobial effectiveness against foodborne pathogens such as Listeria monocytogenes. The objectives of this study were identify and analyze the expression of enterocin genes of Enterococcus isolated from breast-fed infants and evaluate the ability to inhibit three human isolates of virulent Lis-teria monocytogenes, as well as some probiotic bacteria. The susceptibility of the strains of L. mon-ocytogenes to fifteen antibiotics was tested, detecting resistance to cefoxitin (constitutive-ly resistant), oxacillin and clindamycin. Production of enterocins A, B and P were observed in Enterococcus faecium isolates, and enterocin AS-48 in an Enterococcus faecalis isolate. AS-48 showed antilisterial activity by itself, while the joint action of enterocins A and B, or B and P was neces-sary for inhibiting L. monocytogenes, demonstrating a synergistic effect of those combinations. The presence of multiple enterocin genes does not assured the inhibition of L. monocytogenes strains. However, the expression of multiple enterocin genes showed a good correlation with the inhibition capacity of these strains. Furthermore the potential beneficial strains of lactobacil-li and bifidobacteria examined were not inhibited by any of the enterocins produced individu-ally or in combination, with the exception of Bifidobacterium longum BB536, which was inhibited by enterocin AS-48 and the joint production of enterocins A and B or B and P. The enterocins studied here could be candidates for developing alternative treatments against antibi-otic-resistant bacterial infections. Moreover, these selected enterocin-producing E. faecium strains isolated from breast-fed infants could be used as probiotic strains due to their antilisterial effect as well as the absence of virulence factors.

The development of the additive manufacturing (AM) technology proffers challenging requirements for forming accuracy and efficiency. In this paper, a hybrid additive manufacturing technology combining fusion-based selective laser melting (SLM) and solid-state cold spraying (CS) was proposed in order to enable the fast production of near-net-shape metal parts. The idea is to fabricate a bulk deposit with a rough contour first via “fast” CS process and then add fine structures and complex features through “slow” SLM. The experimental results show that it is feasible to deposit SLM part onto CS part with good interfacial bonding. However, the CS parts must be subject to heat treatment to improve their cohesion strength before being sending for SLM processing. Otherwise, the high tensile residual stress generated during SLM process will cause fracture and cracks in the CS part. After heat treatment, pure copper deposited by CS undergoes grain growth and recrystallization, resulting in improved cohesive strength and release of the residual stress in the CS parts is released. The tensile test on the SLM/CS interfacial region indicates that the bonding strength increased by 38% from 45±7 MPa to 62±1 MPa after the CS part is subject to heat treatment, and the SLM/CS interfacial bonding strength is higher than the CS parts. This study demonstrates that the proposed hybrid AM process is feasible and promising for manufacturing free-standing SLM-CS components.

The substrate N1, N3, N5 -tris(2-hydroxyphenyl)benzene-1,3,5-tricarboxamide (Sensor A) was prepared in the reaction of 1,3,5-benzenetricarboxylic acid (trimesic acid) and o-aminophenol in ethanol. The prepared organic sensor fulfills the chemiluminescent requirements including luminophore, spacer, and suitable binding receptor that distress the probe's luminescent features, providing selective and sensitive detection of mercury and iron ions in aqueous solutions. The sensor selectively detects mercury and iron ions in a water matrix containing various metal ions including sodium, calcium, magnesium, zinc, and nickel. Strong and immediate binding was observed between mercury ions and the substrate at pH 7.0 with a binding affinity toward Hg (II) enhanced by nine folds higher than that observed for iron sensor binding affinity, which makes the substrate a distinctive luminescence sensor for mercury detection at ambient conditions. The sensor shows a linear response toward Hg (II) in the concentration range from 4.2 x 10-5 to 2.0 x 10-8 M with a limit of detection of 1.0 x 10-8 M. Further, Sensor A provides linear detection for iron ions in the range from 1.5 x 10-3 to 1.5 x 10-8 M. The measured adsorption capacity of Sensor A toward mercury ions ranged from 1.25 to 1.97 mg/g and the removal efficiency from water samples reached 98.8% at pH 7.0. The data demonstrate that Sensor A is an excellent probe for detecting and removing mercury ions from water bodies.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

In order to understand the evolution of multicellularity, we must understand how and why selection favors the first steps in this process: the evolution of simple multicellular groups. Multicellularity has evolved many times in independent lineages with fundamentally different ecologies, yet no work has yet systematically examined these diverse selective drivers. Here we review recent developments in systematics, comparative biology, paleontology, synthetic biology, theory, and experimental evolution, highlighting ten selective drivers of simple multicellularity. Our survey highlights the many ecological opportunities available for simple multicellularity, and stresses the need for additional work examining how these first steps impact the subsequent evolution of complex multicellularity.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

Despite the implementation of control strategies, the invasive parasitic mite Varroa destructor remains one of the principal causes of honey bee (Apis mellifera) colony losses in numerous countries. For this reason, the parasite represents a serious threat to beekeeping and to agro-ecosystems that benefit from the pollination services provided by honey bees. Numerous selection programmes have been initiated over the last three decades with the aim of promoting the establishment of balance in the host–parasite relationship and, thus, helping European honey bees to survive in the presence of the parasite without the need for acaricide treatments. Such programmes have focused on either selective breeding for putative resistance traits or natural selection. To date, no clear overview of these attempts has been available, which has prevented building on past successes or failures and, therefore, hindered the development of a sustainable strategy for solving the V. destructor problem. In the present study, we review past and current selection strategies, report on their outcomes and discuss their limitations. Based on this state-of-the-art knowledge, we propose a strategy for increasing response to selection and colony survival against V. destructor infestations. Developing in-depth knowledge regarding the selected traits, optimising selection programmes and communicating their outcomes are all crucial to our efforts to establish a balanced relationship between the invasive parasite and its new host.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

The dopamine D3 receptor is an important CNS target for the treatment of a variety of neurological diseases. Selective dopamine D3 receptor antagonists modulate the improvement of psychostimulant addiction and relapse. In this study, five and six featured pharmacophore models of D3R antagonists were generated and evaluated with the post-hoc score combining two survival scores of active and inactive. Among Top 10 models, APRRR215 and AHPRRR104 were chosen based on the coefficient of determination (APRRR215: R2training = 0.80; AHPRRR104: R2training = 0.82) and predictability (APRRR215: Q2test = 0.73, R2predictive = 0.82; AHPRRR104: Q2test = 0.86, R2predictive = 0.74) of their 3D-quantitative structure–activity relationship models. Pharmacophore-based virtual screening of a large compound library from eMolecules (> 3 million compounds) using two optimal models expedited the search process 100-fold speed increase compared to the docking-based screening (HTVS scoring function in Glide) and identified a series of hit compounds having promising novel scaffolds. After the screening, docking scores, as an adjuvant predictor, were added to two fitness scores (from the pharmacophore models) and predicted Ki (from PLSs of the QSAR models) to improve accuracy. Final selection of the most promising hit compounds were also evaluated for CNS-like properties as well as expected D3R antagonism.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

An original approach has been proposed for designing a nanofibrous (NFs) layer using UV-cured polyvinylpyrrolidone (PVP) as a matrix, incorporating mesoporous graphene carbon (MGC) nanopowder both inside and outside the fibres, creating a sandwich-like structure. This architecture is intended to selectively adsorb and detect acetic acid vapours, which are known to cause health issues in exposed workers. The nanocomposite MGC-PVP-NFs layer was fabricated through electrospinning deposition onto interdigitated microelectrodes (IDEs) and stabilised under UV-light irradiation. To enhance the adhesion of MGC onto the surface of the nanocomposite polymeric fibres, the layer was dipped in a suspension of polyethylenimine (PEI) and MGC. The resulting structure demonstrated promising electrical and sensing properties, including rapid responses, high sensitivity, good linearity, reversibility, repeatability, and selectivity towards acetic acid vapours. Initial testing was conducted in a laboratory using a bench electrometer, followed by validation in a portable sensing device based on consumer electronic components (by ARDUINO®). This portable system was designed to provide a compact, cost-effective solution with high sensing capabilities. Under room temperature and ambient air conditions, both laboratory and portable tests exhibited favourable linear responses, with detection limits of 0.16 and 1 ppm, respectively.

A review on planar printed structures that are based on Matryoshka-like geometries is presented. These structures use the well-known principle of Matryoshka dolls that are successively nested inside each other. The well-known advantages of the planar printed technology and of the meandered nested Matryoshka geometries are combined to generate miniaturized, multi-resonance and/or wideband configurations. Both metal and complementary slot structures are considered. Closed and open configurations are analyzed. The working principles are explored do get physical insight of their behavior. Low cost and single layer applications as frequency selective surfaces, filters, antennas, and sensors, in the microwave frequency region, are reviewed. Potential future research perspectives and new applications are discussed.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

The objective of the present report is the dissemination of information acquired during the application of ISO 6579-1:2017 for the isolation of Salmonella spp. from swine samples. ISO 6579-1:2017 is the officially recommended by the EU protocol for the isolation of Salmonella spp., aiming in the harmonization of effective successful control of Salmonella infection in food producing animals. Successful control of animal salmonellosis is highly dependent on the sensitivity of the biochemical methods reliably detecting the presence of the pathogen in various stages of food production. Application of ISO 6579-1:2017 resulted in the isolation of twelve Salmonella spp. and eighteen other members of the family of Enterobacteriaceae biochemically and antigenically resembling salmonellae. The findings necessitated in the depth evaluation of the culture media xylose-lysine-desoxycholate agar (XLD), Salmonella-Shigella Agar (SS), Brilliant Green Agar (BGA), Salmonella Chromogenic Agar (SCA), Triple Sugar Iron (TSI) and modified semi-solid Rappaport–Vassiliadis (MSRV) agar. The evaluation showed that these culture selective media differed significantly in their performance regarding the isolation of Salmonella from swine samples. It was concluded that the presence of atypical Salmonella strains negatively affects the prevalence of Salmonella, thus the identification of carrier pigs, eventually affecting the efficiency of control programs. Thus, doubtful results require additional biochemical testing for confirming the accuracy of such universally recommended isolation methods.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.