The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

Gadolinium-based contrast agents (GBCA) are complexes, highly stable in vivo, used in Magnetic Resonance Imaging (MRI), administered in patients and then eliminated via renal, passing through wastewater treatment plants (WWTP) before being discarded in the receiving medium, without apparent removal. In this study, it was studied if different exposure periods to several environmental parameters (solar radiation, different salinities, temperatures and pH) will influence the stability of these complexes, namely, the Gd-DOTA. Gd-DOTA solutions were processed in a seaFAST-pico saline matrix pre-concentration and elimination system and Gd concentrations were determined by ICP-MS. Results showed that the complex remained stable in fresh, brackish and saline water environments, even when exposed to extreme temperatures (40ºC) or slightly acidic to basic conditions (6-10), for an exposure period of 96h. A small increase in the free Gd concentration was observed after 18 days when exposed to pH<4, in all tested salinities (0, 18 and 36 PSU), with a degradation increase of up to 29%, after 5 weeks of exposure in freshwater. When exposed to direct solar radiation a low Gd-DOTA degradation (4%) was observed after 24h at salinity 18 PSU and remained constant until the end of the exposure period (96h), while the remaining salinities showed negligible values.

Laportea bulbifera (Sieb. et Zucc.) Wedd. (L. bulbifera) is a significant plant belonging to the Laportea genus. It has been traditionally used in ethnomedicine to treat various conditions such as rheumatic arthralgia, fractures, falling injuries, nephritis dropsy, limb numbness, pruritus, fatigue-induced internal imbalances, and irregular menstruation. Modern pharmacological studies have confirmed its therapeutic potential, as it exhibits anti-inflammatory, immunosuppressive, analgesic, and anti-rheumatoid arthritis properties. In order to gather in-depth information on L. bulbifera, a comprehensive literature search was conducted using databases such as Web of Science, PubMed, ProQuest, and CNKI. This review aims to provide a comprehensive understanding of L. bulbifera by covering various aspects, including ethnomedicinal uses, geographical distribution, botanical description, phytochemistry, pharmacology, and quality control. By doing so, this review intends to lay a strong foundation and propose new research avenues for the exploration and development of potential applications of L. bulbifera. Thus far, a total of 189 compounds have been isolated and identified from L. bulbifera. These compounds include flavonoids, phenolics, nitrogen compounds, steroids, terpenoids, coumarins, phenylpropanoids, fatty acids and their derivatives, and other compounds. Notably, flavonoids and fatty acids in L. bulbifera have demonstrated remarkable antioxidant and anti-inflammatory properties. Furthermore, these compounds show promising potential in activities such as analgesia, hypoglycemia, and hypolipidemia, as well as toxicity. Despite the extensive fundamental studies conducted on L. bulbifera, further research is still needed to enhance our understanding of its credible mechanism of action and improve its quality control. This necessitates more comprehensive investigations to explore the specific material basis, uncover new mechanisms of action, and refine the quality control methods related to L. bulbifera. By doing so, we could contribute to the further development and utilization of this plant.

The leaf essential oils from five Eucalyptus spp.: E. astringens, E. camaldulensis, E. lehmanii, E. leucoxylon and E. sideroxylon growing in the same plantation area and conditions (plants with the same age and subjected to the same agronomic practices) were analyzed and evaluated for their antimicrobial activity. The essential oil yields ranged from 0.14 to 0.96% (w/w), and their chromatographic profiles were resolved into 48 compounds; among them, 11 were common to all essential oils. Terpenoids (oxygenated mono, and sesquiterpenes) dominated (55.66-76.67%) the oil profiles. Although 1,8-cineole (21.97-50.93%) was found as the main oxygenated monoterpene in all examined essential oils, principal component analysis observed and confirmed an interspecific chemical variability. Additionally, a set of distinctive chemical markers that could serve as a reliable tool for discrimination of Eucalyptus species and for authentication and quality control purposes (for commercial samples) has been defined for each essential oil. The antimicrobial disc-diffusion assay results revealed that all essential oils were endowed with a strong antimicrobial activity, with those derived from E. camaldulensis, E. lehmanii and E. leucoxylon being the most active.

A tunable near-infrared surface plasmon resonance (SPR) biosensor based on gate-controlled graphene plasmons is investigated theoretically. The novel characteristics of chemical potential sensing make the proposed sensor promising in the application of ultra-sensitive and highly specific biosensing technology. The sensitivity of chemical potential sensing in wavelength interrogation mode can be calculated to be 1.5, 1.89, 2.29, 3.21, 3.73 and 4.68 nm/meV respectively at the central wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. The much smaller full width half maximum (FWHMs) comparing with that of 2D nanomaterial-enhanced metal SPR sensors indicates higher figure of merit. The sensitivity of chemical potential sensing in gate voltage interrogation mode also can be calculated to be 156.9822, 143.6147, 131.0779, 111.0351, 101.3415 and 90.6038 mV/meV respectively at the incident wavelength of 1100, 1200, 1310, 1550, 1700 and 1900 nm. It can be estimated theoretically that the limit of detection (LOD) in DNA sensing of the proposed sensor can reach femtomolar level and even attomolar level, comparable to and even lower than that of 2D nanomaterial-enhanced metal SPR sensors with AuNPs as a sensitivity enhancement strategy. The feasibility of preparation and operation of this new concept SPR biosensor is also analyzed and discussed.

We successfully fabricated Ag@Cu2O core-shell decorated on reduced graphene oxide (rGO) nanocomposites (ACRN) by a simple and convenient in situ substitution method. The properties of these ACRN with heterostructure layers were characterized by scanning and transmission electron microscopies and absorption spectroscopy. We used p-nitrophenol (4-NP) as a probe molecule to determine the chemical catalytic activity of the ACRN. Upon introduction of rGO, a high electron transfer efficiency was achieved; thus, the catalytic activity was improved significantly. Therefore, the ACRN exhibited significantly improved catalytic activity for the reduction of 4-NP and showed the high application value in the removal of toxic and harmful substances from water. In addition, the fabricated ACRN was used for the reduction of organic dyes and explosive pollutants to generate nontoxic products. Furthermore, the high charge redistribution and transfer among Ag, Cu2O and rGO in the ACRN induced the high catalytic reduction of organic pollutants, indicating the excellent potential of these materials for applications in water pollution treatment.

Background: Poisoning is a growing public problem that has shown increased prevalence in many countries worldwide, contributing to increased costs and mortalities. A lack of or insufficient information regarding the circumstances, chemicals, drugs and people at risk due to imperfect reporting system is regarded as a barrier to successful poisoning prevention and intervention efforts. In Saudi Arabia, poisoning cases are monitored at the central level in the Ministry of Health, with meticulous follow-up of cases across country areas through public health departments. The current study's objective was to describe the poisoning notification and reporting system in Makkah.Subjects and methods: All reports of chemical and drug overdose poisoning delivered to the environmental health and occupational safety department in Makkah Almukarramah over two years (2018-2019) were reviewed, together with verification of all systems, rules and guidelines organizing the performance of the department.Results: The total number of cases reported in 2018 was 209 cases, while it reached 42 cases in 2019. The overwhelming majority of the cases were Saudi (91.6%), with a slight predominance of males (57.4%) over females (42.6%). Generally, almost two-thirds of the cases occurred in children below 13 years (61.4%), most of the poisoning cases resulted from drug overdose (63.3%), while 34.7% were chemical poisoning. The most common drug poisoning was attributed to analgesics followed by antiepileptics, antihypertensive drugs, antipsychotics and antimicrobials, while cleaning and detergent agents were the most commonly poisoned chemicals. The majority of these agents were taken by the oral route. Children's chemical poisoning was significantly higher than that in older age groups (p<0.05). All intentional poisoning occurred in adults; the great majority of them (88.9%) used drug overdosing rather than chemical substances.Conclusion and recommendations: The current study results are consistent with most of the previous studies carried out in different regions in Saudi Arabia. Reviewing the performance and adherence of the “Environmental Health and Occupational Safety Department” to the guidelines and instruction regulating monitoring, notification and reporting of poison cases are satisfactory and the poisoning surveillance system is effective. Further in-depth studies are needed to elaborate other socioeconomic and demographic factors associated with chemical and drug overdose poisoning. Public health plans, policies and legislations should be implemented to reduce these factors, including prohibition over-the-counter pharmaceutical sales, selling the possibly harmful substances in kid-proof bottles and additional stringent rules governing chemical sale and storage. Intensive supervision of children is needed. Suicidal poisoning patients should seek psychiatric help to limit the possibility of attempting suicide again in the future. Furthermore, efforts are needed to plan and implement health education programs and campaigns about the factors proven in the current study to be significantly related to chemical and drug overdose poisoning to raise public knowledge about exposure to chemicals and its consequences. Popular communication media, commercial malls, road ads, learning institutions and workplaces can be used to deliver health education campaigns and programs. Advice on how to store chemicals safely and how to keep kids safe should be focused on during such programs.

China Xihu Longjing tea famous for its good flavor and quality. However, the related metabolites information except flavonoids is largely deficient. Different processing methods of China Xihu Longjing tea fixing both by machine at first and second step(A1), first step by machine and second step by hand(A2), first step by hand and second step by machine(A3), both by hand at first and second step (A4) were compared using a UHPLC-QE-MS-based metabolomics approach. Liquid chromatography-mass spectrometry was used to analyze the metabolic profiles of the processed samples. A total of 490 metabolites (3 alkaloids, 3 anthracenes, 15 benzene and substituted derivatives, 2 benzopyrans, 13 coumarins and derivatives, 128 flavonoids, 4 furanoid lignans, 16 glycosides and derivatives, 5 indoles and derivatives, 18 isocoumarins and derivatives, 4 chalcones and dihydrochalcones, 4 naphthopyrans, 3 nucleosides, 78 organic acids and derivatives, 55 organooxygen compounds, 5 phenols, 109 prenol lipids, 3 saccharolipids, 3 steroids and steroid derivatives, 17 tannins) were identified. The different metabolism profiles were distinguished using PCA and OPLS-DA. There were differences in the types and contents of metabolites, especially flavonoids, furanoid lignans, glycosides and derivatives, organic acids and derivatives and organooxygen compounds. There was a positive correlation between flavonoid metabolism and amino acid metabolism. However, there was a negative correlation between flavonoid metabolism and amino acid metabolism, which had the same trend as prenol lipids metabolism, tannin.This study provides new valuable information for regarding differences in the metabolite profile of China Xihu Longjing tea processed based on machine fixing and manual fixing methods.

Background: Poisoning is a challenging medical condition facing health care providers, as it usually results in serious outcomes in terms of morbidities or mortalities. Poisoning is a challenging medical condition facing health care providers, as it usually results in serious outcomes in terms of morbidities or mortalities. The lack of or inadequate information about the circumstances, substances and populations at risk are considered barriers to the actual prevention of poisoning and effective intervention strategies in Saudi Arabia. The aim of the current study was to describe the pattern and determinants of chemical and drug overdose poisoning in Makkah.Subjects and methods: All reports of chemical and drug overdose poisoning delivered to the Environmental Health and Occupational Safety Department in Makkah over two years (2018-2019) were reviewed.Results: The total number of cases reported in 2018 was 209 cases, while it reached 42 cases in 2019. The overwhelming majority of the cases were Saudi (91.6%), with a slight predominance of males (57.4%) over females (42.6%). Generally, almost two-thirds of the cases occurred in children below 13 years (61.4%), most of the poisoning cases resulted from drug overdose (63.3%), while 34.7% were chemical poisoning. The most common drug poisoning was attributed to analgesics followed by antiepileptics, antihypertensive drugs, antipsychotics and antimicrobials, while cleaning and detergent agents were the most commonly poisoned chemicals. The majority of these agents were taken by the oral route. Children's chemical poisoning was significantly higher than that in older age groups (p<0.05). All intentional poisoning occurred in adults; the great majority of them (88.9%) used drug overdosing rather than chemical substances.Conclusion and recommendations: The current study results are consistent with most of the previous studies carried out in different regions of Saudi Arabia. Further in-depth studies are needed to elaborate other social and demographic factors associated with chemical and drug overdose poisoning. Public health plans, policies and legislations should be implemented to reduce these factors. Intensive supervision of children is needed. Suicidal poisoning patients should seek psychiatric help to limit the possibility of attempting suicide again in the future. Furthermore, efforts are needed to plan and implement health education programs about the factors proven in the current study to be significantly related to chemical and drug overdose poisoning.

Speciation analysis is a relevant topic since the (eco)toxicity, bioavailability, bio (geo)chemical cycles, and mobility of a given element depend on its chemical forms (oxidation state, organic ligands, etc.). Reliability of analytical results for chemical species of elements depends mostly on the maintaining of their stability during sample pretreatment step and on the selectivity of further separation step. Solid phase extraction (SPE) is a matter of choice as most suitable and widely used procedure for both enrichment of chemical species of elements and their separation. Features of sorbent material are of great importance to ensure extraction efficiency from one side and selectivity from other side of SPE procedure. This review presents an update on the application of polymeric materials in solid-phase extraction used in non-chromatographic methods for speciation analysis.

The basis of modern teeth whitening systems is the use of a whitening gel, usually containing hydrogen peroxide or carbamide peroxide. The purpose of our study was to evaluate the effect of chemical and modified office teeth whitening systems on the mineral metabolism of oral fluid and to determine a safer method. The study covered 81 patients aged 22 to 35 years of both sexes with teeth color A2 and darker on the Vita Classic scale. Determination of the concentration of calcium and phosphates in the oral fluid was carried out on a spectrophotometer using ready-made Human kits. Chemical tooth whitening was performed using a gel based on 40% hydrogen peroxide. After the procedure, remineralization therapy with enamel-sealing liquid was performed for 14 days. The obtained results indicate that the most pronounced changes in the content of calcium (+74.4%, p &lt;0.001) and рhosphates (phosphorus) (-23.07%, p &lt;0.001) were observed when using a chemical bleaching system. After the teeth whitening procedure using a modified technique, less pronounced changes in the concentrations of calcium (+29.07, p &lt;0.001) and phosphorus (-14%, p &lt;0.001) were observed. The use of remineralizing agents led to a faster recovery of the initial levels of calcium and phosphates in the oral fluid. Both bleaching systems caused similar changes in the chemical composition of the oral fluid.

Given its exceptional attributes, aerogel is viewed as a material with immense potential. Being a natural polymer, cellulose offers the advantage of being both replenishable and capable of breaking down naturally. Cellulose-derived aerogels encompass the replenish ability, biocompatible nature, and ability to degrade naturally inherent in cellulose, along with additional benefits like minimal weight, extensive porousness, and expansive specific surface area. Even with increasing appreciation and acceptance, the undiscovered possibilities of aerogels within the textile sphere continue to be predominantly uninvestigated. In this context, we outline the latest advancements in the study of cellulose aerogel formulation and their diverse impacts on textile formations. Drawing from the latest studies, we reviewed the materials used for the creation of various kinds of cellulose-focused aerogels and their properties, analytical techniques, and multiple functionalities in relation to textiles. This comprehensive analysis extensively covers the diverse strategies employed to enhance the multi-functionality of cellulose-based aerogels in the textile industry. Additionally, we focused on the global market size of bio-derivative aerogels, companies in the industry producing goods, and prospects moving forward.

Cocoa beans of the CCN-51 clone harvested in the Tumaco region (Nariño, Colombia) were fermented following four different treatments: (1) spontaneously (at room temperature for 120 h) in traditional conditions (Control); (2) traditional processing with a pre-drying (sun-dried for 24 h) treatment (PD); (3) with fermentation (for 120 h) after inoculation of a yeast starter culture (YS); and (4) including both treatments, pre-drying and yeast inoculation (PD+YS). Chemical composition, fatty acids, total polyphenol, methylxanthines (theobromine and caffeine) and lactic acid content of cocoa beans were determined. Chemical and fatty acid composition and theobromine content were not affected by the different fermentation treatment applied. When analysing total polyphenol content, YS and PD+YS treatments significantly increased the content of these compounds at the end of the fermentation process, while PD treatment decreased the caffeine content of cocoa beans. Finally, lactic acid content decreased as a consequence of both inoculation of yeast starter and mainly the pre-drying treatment. In conclusion, solar pre-drying in the open air and the inoculation of a yeast starter treatments could improve the final quality of coca beans.

Effective therapeutics for Alzheimer's disease (AD) are in great demand worldwide. In our previous work, we responded to this need by synthesizing novel drug candidates consisting of 4-amino-2,3-polymethylenequinolines conjugated with butylated hydroxytoluene via fixed-length alkylimine or alkylamine linkers (spacers) and studying their bioactivities pertaining to AD treatment. Here, we report significant extensions of these studies, including the use of variable-length spacers and more detailed biological characterizations. Conjugates were potent inhibitors of acetylcholinesterase (AChE, minimum IC50 15.1±0.2 nM) and butyrylcholinesterase (BChE, minimum IC50 5.96±0.58 nM), with weak inhibition of off-target carboxylesterase. Conjugates with alkylamine spacers were more effective cholinesterase inhibitors than alkylimine analogs. Optimal inhibition for AChE was exhibited by cyclohexaquinoline and for BChE by cycloheptaquinoline. Increasing spacer length elevated potency against both cholinesterases. Structure-activity relationships agreed with docking results. Mixed-type reversible AChE inhibition, dual docking to catalytic and peripheral anionic sites, and propidium iodide displacement suggested the potential of hybrids to block AChE-induced β-amyloid (Aβ) aggregation. Hybrids also exhibited inhibition of Aβ self-aggregation in the thioflavin test; those with a hexaquinoline ring and C8 spacer were the most active. Conjugates demonstrated high antioxidant activity in ABTS and FRAP assays as well as inhibition of luminol chemiluminescence and lipid peroxidation in mouse brain homogenates. Quantum-chemical calculations explained antioxidant results. Computed ADMET profiles indicated favorable blood-brain barrier permeability suggesting CNS activity potential. Thus, the conjugates could be considered promising multifunctional agents for potential treatment of AD.

Reactions of picolinamides with 1,3-propanesultone in methanol followed by the treatment with ketones led to a series of previously unknown chemical transformations, yielding first pyridinium salts (2a-f) with a protonated endocyclic nitrogen atom and then heterocyclic salts (3a-j) containing a 4-imidazoline ring. The structures of intermediate and final products were determined by IR and 1H, 13C NMR spectroscopy and X-ray study. The effects of the ketone and alcohol structures on the product yield were studied by quantum-chemical calculations. The stability of salts 3a-j towards hydrolysis and alcoholysis makes them excellent candidates for the search of new types of biologically active compounds.

Abstract: Agriculture uses plastic products for containers, packaging, tunnels, drip irrigation tub-ing, mulches. Large amounts of plastics are used as mulches on the soil surface for vegetable pro-duction (tomato, cucumber, watermelon, strawberry, vine) to reduce the weed competition, in-crease water and fertilizer use efficiency and enhance crop yield. Portugal uses around 4,500 t/year of polyethylene plastic to cover approximately 23,000 ha of agricultural land and only a small amount is recovered for recycling or secondary uses because of dirt with soil, vegetation, pesticide and fertilizers. Cleaning and decontaminating polyethylene mulch are costly and commercial technology is often not accessible nor economically viable in the current economic Portuguese situation. Most plastic mulch is composed of polyethylene that degrades slowly and produces a large quantity of residues in soil with negative impact in the environment. In the present study, the effects of long-term cultivation of blueberry using green 100% high density polyethylene mulch, in the south Portugal were evaluated for soil chemical and biological changes. High density green plastic mulch did not contaminate the topsoil with di(2-ethylhexyl) phthalate and heavy metals, buttotal nitrogen and organic carbon concentrations, electric conductivity and microbial activity were reduced in the planting row compared with bare soil, without mulching. Further-more, the presence of plastic mulch did not affect negatively the presence of nematodes, and the Rhabditida (bacterial feeders) increased in the planting and covered row.

The aim of the study was to verify whether a 20 and 40% reduction of nitrogen (N) fertilization rate will be sufficient to maintain soil basic chemical features, fertility, and yielding in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (PL) system. In addition, it was examined which tillage system (PL, NT) allows reduction of fertilization while maintaining good yields of the tested soils. Two fields (10 ha each) were established for PL and NT maize cultivation and soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical and biological parameters (i.e. pH, forms of nitrogen, phosphorus and carbon, content of selected macronutrients and humic substances, respiration activity) were monitored during the experiment. It was evidenced that the 20% reduction in N fertilization does not have an adverse effect on the chemical and biological characteristics of soils. In turn, the maize yield was mainly the result of both the tillage system and the N rate, i.e. it was significantly higher in the PL system.

Thymus is an herbaceous perennials or subshrubs of the Lamiaceae family and is widely distributed worldwide. Essential oils extracted from thymus have attracted much attention owing to their potential biological functions. Here, we evaluated the chemical compositions of eight thyme essential oils (TEOs) using gas chromatography-mass spectrometry and assessed their antioxidant activity and in potential role in antibacterial and tumor therapy. The results showed that (1) the main components in eight TEOs were monoterpene hydrocarbons and oxygenated monoterpenes, and the chemical compositions of TEOs were affected by the specie factor; (2) eight TEOs could be divided into 3 groups (thymol-, geraniol-and nerol acetate-type), and thymol was main type; (3) eight TEOs had some common compounds, such as thymol and p-cymene, which were the main components in seven TEOs; (4) eight TEOs had antioxidant activit, and thymol-type EOs had strong antioxidant activity, while geraniol-type EOs had relatively weak antioxidant activity. In addition, it was found thymol had strong antibacterial activity against the growth of Escherichia coli and Staphylococcus aureus, and antimigratory activity of A549 cell. Overall, our results can provide theoretical basis for further exploring the function of natural products from thyme essential oils.

Studying the distribution and transport dynamics of cations in plants is crucial for understanding their response mechanisms to saline-alkali stress conditions. However, our current understanding of how restoration measures affect cation distribution and transport in plants is surprisingly limited. To address this gap, we conducted a split-plot experiment using Medicago sativa L. cv. “Zhongmu No. 1” to investigate the combined effects of biological and chemical restoration measures—with bio-fertilizer as the primary zone and flue gas desulfurization (FGD) gypsum with humic acid as the secondary zone—on soil properties, plant growth, and the content, distribution, and transport of cations in plants. The results revealed that different restoration strategies decreased soil alkalinity and enhanced plant growth. Significantly, bio-fertilizer exhibited positive effects on plant growth and yield. On the contrary, FGD gypsum with humic acid reduced the soil's pH level, exchangeable sodium percentage, and sodium adsorption ratio, while increasing the contents of K+, Ca2+, and Mg2+ in the soil. The triple combination of FGD gypsum and humic acid with bio-fertilizer reduced Na+ transport in M. sativa by enhancing the selective absorption of beneficial ions, such as K+, Ca2+, and Mg2+ in leaves, and by facilitating the transport of Ca2+ and Mg2+ from roots and stems to the leaves. Therefore, the application of FGD gypsum and humic acid combined with bio-fertilizer has the potential to decrease soil alkalinity and the proportions of water-soluble ions in the soil, ultimately enhancing the translocation of key ionic components to leaves. This, in turn, increases the salt tolerance of plants and promotes their growth. Our results offer new insights into the interactions among measures, soil, and plants in saline-alkali land restoration, providing practical solutions for the restoration of saline-alkali soil.

In response to global climate challenges and the increasing demand for energy, exploring renewable energy alternatives has become crucial. Bio-oils, derived from biomass pyrolysis, are emerging as potential replacements for fossil fuel-based liquid fuels. This paper shares findings from the Institute of Energy and Fuel Processing Technology on the quality of crude biomass pyrolysis bio-oil samples. These findings highlight their potential as motor liquid fuels. The article details the results of tests on the physicochemical properties of four distinct bio-oil samples. Additionally, it presents preliminary test results on the hydrodeoxygenation of bio-oils in a batch reactor. The production of homogeneous, stable mixtures using other fuel additives, such as diesel oil, rapeseed methyl ester (RME), and butanol, is also discussed.

Due to the low content, few studies are focused on the volatile compounds of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (PR, syn. Lamiophlomis rotata (Benth.) Kudô). However, such volatile compounds may have important pharmacological activities such as antioxidant, anticancer. In order to identify the chemical markers (CMs) in the essential oils (Es) and explore the potential bioactivities, we first conduct a thoroughly investigation on the volatile compounds and evaluate their anti-oxidant activities (AOAs), to the best of our knowledge. Light yellow Es with a fresh and elegant smell are obtained by hydro-distillation with an average yield of 0.11% (mL/g). After separation through cryoprecipitation, the crystals (Cs) and EOs removed crystals (RCs) were gotten, respectively. A total of 81 components are qualified and quantified in the Es, Cs and RCs, in which 44 ones are first reported from PR. As for content, the main compounds are long-chain fatty acids (LCFAs) and their esters. Among them, palmitic acid (PA), myristic acid (MA), linoleic acid (LA), oleic acid (OA) and methyl palmitate are highlighted, Besides, hexahydrofarnesyl acetone and phytol are also prominent Four kinds of C13-norisoprenoids are first reported from PR, in which, trans-β-damascenone is potent in flavour. In sum, these eight representative compounds can be chosen as the CMs. The AOAs of Es, Cs, RCs and four CMs such as PA, MA, LA and OA are evaluated by in vitro assays. In general, PA and MA present pro-oxidant activities (POAs) or weak AOAs. LA and OA show POAs or weak AOAs in lower concentration group, whereas demonstrate medium or strong AOAs in higher concentration group. Usually, the RCs demonstrate stronger AOAs and the Cs present weaker AOAs compared with those of the corresponding Es, which should be related to their different content of PA. This study can give some hints on the utilization of such Es which are abundant in LCFAs.

Chitin/chitosan and collagen are two of the most important bioactive compounds with applications in the pharmaceutical, veterinary, nutraceutical, cosmetic, biomaterials, and other industries. When extracted from fish and shellfish non-edible parts, by-catches, and invasive species, their use contributes to a more sustainable and circular economy. The present article reviews the scientific knowledge and publication trends along the marine chitin/chitosan and collagen value-chains and assesses how researchers, industry players, and end-users can bridge the gap between scientific understanding and industrial applications. Overall, research on chitin/chitosan remains focused on the compound itself rather than its market applications. Still, chitin/chitosan use is expected to increase in food and biomedical applications, while that of collagen is expected to increase in biomedical, cosmetic, pharmaceutical, and nutritional applications. Sustainable practices, such as the reuse of waste materials, contribute to strengthen both value-chains; the identified weaknesses include the lack of studies considering market trends, social sustainability, and profitability, as well as insufficient examination of intellectual property rights. Government regulations, market demand, consumer preferences, technological advancements, environmental challenges, and legal frameworks play significant roles in shaping both value-chains. Addressing these factors is crucial for seizing opportunities, fostering sustainability, complying with regulations, and maintaining competitiveness in these constantly evolving value-chains.

Quinoa, known as the "golden grain" for its high nutritional value, is a significant source of essential nutrients, including proteins, minerals, vitamins, polyphenols, phytosterols, and flavonoids. However, the biological functions of quinoa polysaccharides remain understudied. In this research, two crude quinoa polysaccharides extracts (Q-40 and Q-60) were obtained extracting by 40% and 60% alcohol. The purity of Q-40 and Q-60 was 58.29% and 62.15%, with protein contents of 8.27% and 9.60%, respectively. Monosaccharide analysis revealed that Q-40 contained glucose (Glc), galacturonic acid (GalA), and arabinose (Ara) in a molar ratio of 0.967:0.027:0.006. Q-60 was composed of xylose (xyl), arabinose (Ara), galactose, and galacturonic acid (GalA) with a molar ratio of 0.889:0.036:0.034:0.020. The average molecular weight of Q-40 ranged from 47484 to 626488 Da, while Q-60 showed a range of 10025 to 47990 Da. Rheological experiments showed that Q-40 exhibited higher viscosity, while Q-60 demonstrated more elastic properties. Remarkably, Q-60 showed potent antioxidant abilities, with scavenging rates of 98.49% for DPPH and 57.5% for ABTS. Antibacterial experiments using the microdilution method revealed that Q-40 inhibited the growth of Methicillin-resistant Staphylococcus aureus (MRSA) and E. coli, while Q-60 specifically inhibited MRSA. At lower concentrations, both polysaccharides inhibited MDA cell proliferation, but at higher concentrations, they promoted proliferation. Similar proliferation-promoting effects were observed in HepG2 cells. The research provides important information in application of quinoa in food and functional food industries.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

The Mahuagou gold deposit is among the most important gold deposits in the core of Huangling Anticline. However, the geochemical exploration on the surface of the mining area presents challenges due to the thin overburde.This paper focuses on the overburden soil of Fengxiangshugou (FXS) – Mahuanggou (MHG) section as the research object, utilizes chemical form analysis of gold, soil halogen survey, and heat-released mercury survey to determine the key deep-penetrating geochemical methods for mining area. The results indicated that Si and Al components of samples exhibit minimal variation, suggesting that drift loads did not influence the overburden soil. Based on the systematic clustering, As, Sb, Mo, Bi, W and Hg emerge as ore-body or ore-belt front elements of hydrothermal gold deposits. In the study area, the predominant chemical form of gold in soil is the strong organic bond. Compared to the total amount, strong organic bound gold and heat-released mercury show higher anomaly contrasts, making them crucial indicators of faults, intrusions and hidden ore bodies. Consequently, chemical form analysis of gold and heat-released mercury surveys can enhance the anomaly contrast, proving beneficial for geochemical prospecting for weak anomalies in this area.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

We presents results obtained from the numerical simulation of the gas-phase chemical kinetics in atmospheric pressure air non-equilibrium plasmas. In particular we have addressed the effect of pulsed operation mode of a planar dielectric barrier discharge. As it was conjectured, the large difference in the time scales involved in the fast dissociation of molecules in plasmas and their subsequent reactions to produce stable chemical species, makes the presence of a continuously repeated plasma production stage unnecessary and a waste of electrical power and efficiency. Results on NOx remediation, ozone production, water vapor and ammonia dissociation are discussed. A few comparisons with experimental findings in a dielectric barrier discharge reactor already used for applications is briefly addressed too. Our results clearly indicate a pattern for the optimization of the discharge using a carefully designed repetition rate and duty-cycle.

Four decades have elapsed since the first quasiperiodic crystal was discovered in the Al-Mn alloy system, and many progresses have been made during this time interval in the science of quasicrystals (QCs). Notwithstanding this, a significant number of open questions still remain regarding both fundamental and technological aspects. For instance: What are QCs good for? How can we improve the current provisional QC definition? What is the role of the underlying quasiperiodic order and the characteristic inflation symmetry of these compounds in the emergence of their unusual physicochemical properties? or, What is the nature of chemical bonding in QCs formed in such different sorts of materials as alloys, oxides, or organic polymers? In this essay I will discuss these, and other closely related, issues from an interdisciplinary perspective and will comment on appealing prospectives in the field for the years to come.

Tomato quality is intricately regulated by a combination of factors, including the presence of bioactive compounds referred to as secondary metabolites and various organoleptic characteristics. These attributes are notably influenced and harmonized by the specific growing conditions, with a particular emphasis on the type of fertilization employed. Traditionally, chemical fertilizers have been favoured in crop cultivation due to their cost-effectiveness and ability to accelerate crop growth. However, in pursuit of sustainable and intelligent agricultural practices, there is a growing need for alternative fertilizers. In this context, the present study aimed to assess the impact of fertilizers derived from waste materials, specifically sulphur bentonite and orange residue (referred to as SB), on tomato quality. This assessment extended to examining qualitative and quantitative alterations in aroma-related volatile compounds and the antioxidant systems of tomatoes, in comparison to the conventional use of fertilizers such as horse manure and NPK (nitrogen, phosphorus, and potassium). The results obtained revealed distinct effects of different fertilizers on tomato quality. Notably, parameters such as TPRO (total protein), TCARB (total carbohydrate), LIC (lycopene content), TCAR (total carotenoid content), total phenols, total flavonoids, and aroma profiling exhibited significantly superior values in the group treated with SB fertilizer. These findings strongly suggest that the novel fertilizer functioned as a bio-stimulant, enhancing the nutraceutical and sensory attributes of tomatoes, with a pronounced impact on the synthesis of secondary metabolites and the aroma profile of the fruits.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

Ranging from traditional food packaging, clothing, and furniture to the current small and large electronic devices and automobiles, plastics serve to fulfill diverse demands in our daily lives. However, the global plastic waste generation is dramatically escalating, currently standing at approximately 150 million metric tonnes annually. While some of regenerated plastics recycled by mechanical methods can be used as their parent plastics, cost and energy savings are limited by multiple preliminary processes such as plastic sorting, shredding, washing, and drying. Moreover, the continuous mechanical recycling process degrades the physical properties of the materials. In this context, chemical recycling is emerging as a promising alternative method due to its high efficiency, simple preliminary steps, reducing reliance on fossil resources, and conversion of plastic waste into value-added chemicals. This review provides a state-of-the-art overview of contemporary chemical recycling of polymeric materials via i) depolymerization: “polymers to small valuable molecules” and ii) closed-loop cycles: “polymers to monomers, and/or to polymers”, by encompassing both traditional/advanced depolymerization chemistries and the remaining challenges. These recycling approaches are contextualized within the present industrial technologies, key design principles, and specific recycling case studies related to distinct polymeric materials.

One of the key pathogenetic links of type 2 diabetes mellitus (T2DM) is the formation of insulin resistance (IR). Besides a wide selection of synthetic antidiabetic drugs, various plant-origin extracts are also available to support the treatment of T2DM. This study aimed to investigate and gain knowledge of the chemical composition and potential IR correction effect of American cranberry (Vaccinium macrocarpon Aiton) leaf extracts and formulate novel 3D-printed oral dosage forms for such extracts. The bioactivity and IR of L-arginine-loaded cranberry leaf extracts were studied in vivo in rats. The cranberry leaf extracts consisted of quinic, 3-caffeoylquinic (chlorogenic), p-coumaroylquinic acids, quercetin 3-O-galactoside, quercetin-3-O-glucoside, quercetin-3-xyloside, quercetin-3-O-arabino-pyranoside, quercetin-3-O-arabinofuranoside, quercetin 3-O-rhamnoside and quercetin-O-p-coumaroyl-hexoside-2 identified by HPLC. In-vivo studies with rats showed that the oral administration of the cranberry leaf extracts had a positive effect on insulin sensitivity coefficients under ITT test, and affected HOMA-IR levels and liver lipid content with experimental IR. A novel 3D-printed immediate-release dosage form was developed for the oral administration of cranberry leaf extracts using polyethylene oxide (PEO) as a carrier gel in a semi-solid extrusion (SSE) 3D printing. In conclusion, American cranberry leaf extracts loaded with L-arginine could find uses in preventing health issues associated with IR.

Hydrogels are water-absorbing polymers that can hydrate forage plants in the soil. The objec-tive was to evaluate the replacement of synthetic hydrogels derived from petroleum by biode-gradable hydrogels in Mombaça grass pastures (Megathyrsus maximum). The experimental treat-ments consisted of: No hydrogel (NH); Synthetic commercial hydrogel (CH), made from a syn-thetic polyacrylamide product; and Biodegradable test hydrogel (TH), obtained from cashew gum (Anacardium occidentale). The experimental design was randomized blocks with five replica-tions and three treatments. Morphogenesis, production, chemical and mineral composition of the Mombaça grass pasture were assessed. The data was subjected to analysis of variance and mean comparison by the Snott-Knott test at 5% probability. Leaf elongation rate was 42.3 mm day-1 in the TH treatment, which was higher (P<0.05) than NH (35.0 mm day-1). Green leaf mass yield was higher in TH in comparison to NH and CH. On the other hand, there was no effect of hydration on chemical composition. The mineral composition of Mombaça grass showed more Zn when TH was used. It can be concluded that biodegradable hydrogels can replace synthetic commercial hydrogels in pastures.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

This paper initiates the study of the mathematical aspects of the ad-hoc Lanzhou index. If G is a graph with the vertex set {x1,⋯,xn}, then the ad-hoc Lanzhou index of G is defined by Lz¯(G)=∑i=1ndi(n−1−di)2, where di represents the degree of the vertex xi. Several identities for the ad-hoc Lanzhou index, involving some existing topological indices are established. The problems of finding graphs with the extremum values of the ad-hoc Lanzhou index from the following sets of graphs are also attacked: (i) set of all connected ξ-cyclic graphs of a fixed order, (ii) set of all connected molecular ξ-cyclic graphs of a fixed order, (iii) set of all graphs of a fixed order, (iv) set of all connected molecular graphs of a fixed order.

This study evaluated the exogenous application of PGRs substitute chemical fertilization without compromising the growth and yield of tomato in fluctuated day-night temperature and humidity stressed late winter. Two-factor experiment comprising chemical fertilizers at 100, 110, 90 and 80 % of recommended doses besides control and PGRs of GA3; NAA, 4-CPA and SA @ 50 ppm including control was conducted where treatments were assigned in triplicates. Results revealed no significant variation among the fertilizer doses (80% to 110% of recommendation) regarding growth and yield contributing traits while among the PGRs, GA3 @ 50 ppm produced maximum number of flower clusters plant-1 (16.85), flowers (8.80) and fruits (5.79) cluster-1, single fruit weight (67.83 g) and fruit yield (6.61 kg plant-1) of tomato that was statistically identical with the findings of SA. But significant reduction in yield was noted in NAA and 4-CPA (1.20 kg and 1.21 kg plant-1, respectively). Interestingly, GA3 and SA in combination with any doses of the studied fertilizers maximize the tomato morphological and reproductive traits while fertilizer plus NAA and 4-CPA interaction gave the inferior results. Further, correlation matrix and PCA findings revealed that five fertilizer doses have no distinctiveness whereas GA3 and SA has distinct position than other PGRs with the maximum dependent variables those were contributed positively in the total variations. The study findings suggested that 20% fertilizer requirement could be reduced with the substitution of GA3 and SA @ 50 ppm for successful cultivation of tomato in late winter having the extreme environmental issues.

In this study, a field experiment was conducted to evaluate the growth and yield responses of Sri Lankan lowland rice (Oryza sativa L.) with the application of beneficial Arbuscular mycorrhizal fungi (AMF) inoculum, and inter-cropping with highly mycorrhizal dependent vetiver grass (Chrysopogon zizanioides L.) under two different soil nutrient management systems (NMSs): conventional/chemical (CNMS) and organic (ONMS). The experiment was designed as a split plot with three blocks. Each CNMS and ONMS experiment included untreated control (T0), and three treatments—AMF inoculation (T1), vetiver intercropping (T2), and the combination of AMF and vetiver (T3). According to the results, colonization of rice roots with AMF was not affected significantly by the treatments and ranged from 0‒15.8%. The effect was very low or absent in the early stage and then higher in the later stages of the rice plant. Furthermore, plant growth was not significantly different between the two NMSs, although grain yield was significantly higher (P &lt; 0.05), with the order T1 (0.45 kg/m2) &gt;T2 (0.42 kg/m2) &gt;T3 (0.41 kg/m2) in CNMS and T2 (0.44 kg/m2) &gt;T1 (0.41 kg/m2) &gt;T3 (0.40 kg/m2), in ONMS than for the respective controls (T0), thus suggesting beneficial utilization of AMF and vetiver in the lowland rice farming system.

Although the effect of thermal modification (TM) on teak wood color is well documented, a few studies were carried out in closed system processes, as well as it remains unclear the effect of different processes on the same material. This work aimed to verify the effect of closed and open system processes of TM on the color of fast-growing teak wood. Thermally modified wood was evaluated in a closed system at 160 °C (CS160) and in an open system at 185 °C and 210 °C (OS185 and OS210). We measured the moisture content (initial and final) of wood, and the corrected mass loss (CML). The chemical analyses encompassed the contents of alpha-cellulose, hemicelluloses, lignin, and extractives (total, in acetone and dichloromethane). Wood color was measured before and after TM according to the CIEL*a*b* color space. It was possible to achieve the same color using different processes of thermal modification (CS160 and OS210). TM reduced wood lightness (L*), red-green chromaticity coordinate (a*), and yellow-blue chromaticity coordinate (b*). L* and a* had the bigger and lower variations, respectively. The color of thermally modified wood was significantly changed, even at the mildest condition tested (OS185, 0.33% CML).

Antimicrobial peptides (AMPs) have emerged as a promising class of bioactive molecules with the potential to combat infections associated with medical implants and biomaterials. This review article aims to provide a comprehensive analysis of the role of antimicrobial peptides in medical implants and biomaterials, along with their diverse clinical applications. The incorporation of AMPs into various medical implants and biomaterials has shown immense potential in mitigating biofilm formation and preventing implant-related infections. We review the latest advancements in biomedical sciences and discuss the AMPs that were immobilized successfully to enhance their efficacy and stability within the implant environment. We also highlight successful examples of AMP coatings for the treatment of surgical site infections (SSIs), Contact lenses, Dental Applications, AMP-Incorporated Bone Grafts, Urinary tract infections (UTIs), Medical Implants, etc. Additionally, we discuss the potential challenges and prospects of AMPs in medical implants, such as effectiveness, instability and implant-related complications. We also discuss strategies that can be employed to overcome the limitations of AMP-coated biomaterials for prolonged longevity in clinical settings.

Coronary artery disease is the most prevalent cardiovascular disease, claiming millions of lives annually around the world. The current treatment includes surgically inserting a tubular construct called as a stent inside arteries to restore blood flow. However, due to lack of patient-specific design, the commercial products cannot be used with different vessel anatomies. In this review, we have summarized the drawbacks in existing commercial metal stents which face problems of restenosis and inflammatory responses, owing to the development of neointimal hyperplasia. Further, we have highlighted the fabrication of stents using biodegradable polymers, which can circumvent most of the existing limitations. In this regard, we elaborated on utilization of new fabrication methodologies based on additive manufacturing such as three-dimensional printing to design patient-specific stents. Finally, we have discussed on the functionalization of these stent surfaces with suitable bioactive molecules which can prove to enhance their properties in preventing thrombosis and better healing of injured blood vessel lining.

The traditional processing of Dendrobium officinale (DO) is manufactured through five necessary processing steps: fresh strips, drying at 85 °C, curling, molding, and drying at 35 °C (Fengdou), and the antioxidant activity of DO were increased after processing into Fengdou. To comprehensively analyses the changing functional components, a plant-wide target metabolomics were employed. In total, 739 differential ingredients were identified in five processing treatments, mainly highlighting differences in variation with phenolic acids, flavonoids, lipids, and amino acids and their derivatives, and glycosylation of aglycone result in the up-regulation in flavonoid glycosides levels. Temperature is a key step in DO processing production. In addition, the main enrichment of specific differential ingredients was found in five different metabolic pathways, including glucosinolate biosynthesis, linoleic acid metabolism, flavonoid biosynthesis, phenylpropanoid biosynthesis, ubiquinone and other terpene quinone biosynthesis. Correlation analysis clarified that total phenols and flavonoids showed a significant positive correlation with antioxidant capacity. This study provides new insights into the influence of processing processes on DO quality, which may lead to guidance for the high-quality production of DO.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

The study within the current research is focused on theoretical assessment of sustainable aviation fuels (SAF) obtained by blending traditional jet fuels Jet A and different liquids (biodiesel and alcohols) from analytical point of view. Within this paper in-depth analysis ofthe physical-chemical properties of Jet A fuel blended with different biodiesels and alcohols has been performed. Also within the blends Aeroshell 500 oil has been added (5% vol.) for ensuring the lubrication of the turbo engine. The blends consists of: Jet Aaviation fuel + biodieselfrom: palm oil, pork fat, sunflower oil and alcohols: methanol, ethanol and butanol. All the 6 liquids have been blended with Jet A in the following percentages: 10, 20 and 30%. Flash point, kinematic viscosity, density, freezing point, elemental analysis and FTIR analysis have been performed for all the liquids: Aeroshell 500, jet A, jet A + 10, 20, 30% biodiesel from waste palm oil, pork fat and waste sunflower oil, jet A + 10, 20, 30% methanol, ethanol and butanol, biodiesels and alcohols. The obtained results shows the influence of each of the blend’s components on the physical-chemical properties of the blends. Based on the physical-chemical analysis of the blends, conclusions on the behavior of the blends during burning and the gaseous pollutants resulting from the burning process can be drawn.

Recently, polyetheretherketone (PEEK) has shown promising dental applications; although surface treatment is essential for dental applications owing to its poor surface energy and wettability, no consensus on an effective treatment method has been achieved. In this study, we attempt to carboxylate PEEK sample surfaces via Friedel–Crafts acylation using succinic anhydride and AlBr3. The possibility of further chemical modifications using carboxyl groups is examined. The samples are subjected to dehydration–condensation reactions with 1H,1H-pentadecafluorooctylamine and N,N'-dicyclohexylcarbodiimide. The sample surface properties at each reaction stage are evaluated. An absorption band in the 3300–3500 cm-1 wavenumber region is observed. Additionally, peak suggestive of COOH is observed in the sample spectra. Secondary modification diminished the absorption band in 3300–3500 cm-1 and a clear F1s signal is observed. Thus, Friedel–Crafts acylation with succinic anhydride produces carboxyl groups on the PEEK sample surfaces. Further chemical modification of the carboxyl groups by dehydration-condensation reactions is also possible. Thus, a series of reactions can be employed to impart desired chemical structures to PEEK surfaces.

This paper presents the concept of a novel adaptable sensing solution currently being developed under the EU Commission founded PHOTONGATE project. This concept will allow to quantify multiple analytes of the same or different nature (chemicals, metals, bacteria, etc.) in a single test with levels of sensitivity and selectivity at/or over those offered by current solutions. PHOTONGATE relies on two core technologies: a bio-chemical technology (molecular gates) which will confer the specificity and, therefore, the capability to be adaptable to the analyte of interest, and which combined with porous substrates will increase the sensitivity, and a photonic technology based on Local Surface Plasmonic Resonance (LSPR) structures serves as transducer for light interaction. Both technologies are in the micron range, facilitating the integration of multiple sensors within a small area (mm²). The concept will be developed for its application in health diagnosis and food safety sectors. It is thought as an easy-to-use modular concept, which will consist of the sensing module, mainly of a microfluidics cartridge that will house the photonic sensor, and a platform for fluidic handling, optical interrogation, and signal processing. The platform will include a new optical concept, fully Europe Union Made, avoiding optical fibers and expensive optical components.

Textile industry is one of the major industries responsible for environmental pollution globally. This is mainly due to the use of synthetic dyes, toxic ingredients and solvents for dy-ing/treatments/protocols of textiles. Replacement of those non ecofriendly ingredients would be a very challenging target to develop novel sustainable textile dying strategies. Using biobased and bioactive pigments, antibacterial ingredients and especially natural solvents are recently pointed out as substances to included in the related formulations. In this study the dyeing ability of the crude gel prodigiosin produced by non-pathogenic bacteria Serratia plymuthica as a natural pigment was investigated on various multifiber fabrics at different condition (temperature and pH) and by using salts (NaOH and Na2S2O4) and alternative mordants (a conventional: FeSO4 and a new bio-mordant: L-Cysteine (L-Cys)) in the recipes with different compositions and especially replacing of organic solvent with a new type of gel-based Choline chloride (ChCl) : Lactic acid (LA) (1 : 2) deep eutectic solvents (DES) as a dyeing medium. For determination of the dying process performances, the color strength (K/S value) of dyed fabric and the dyeing equalization (dE) parameters were evaluated. The fastness properties of the dyed fabrics which displayed as a higher K/S value and good dE were evaluated. The nylon fabrics dyed with 3.0% owf L-Cys at pH = 8.3 improved the color fastness to washing, while the gel-based ChCl : LA (1 : 2) DES dyebath provided a better color fastness to light. Moreover, the nylon fabrics under these conditions exhibited remarkable anti-microbial activity against Staphylococcus aureus (S. aureus) and Pseudomonas aeruginosa (P. aeruginosa). As conclusion, the use of the crude gel prodigiosin pigment revealed an advantageous ability to dye the textile materials, responding to consumers' demand for more ecological and sustainable products. Furthermore, the natural reducing agent L-Cys, never tested before as a bio-mordant, and the use of gel-based DES as a dyeing medium demonstrated enhanced colorimetric and antibacterial properties on dyed nylon with crude gel prodigiosin pigment.

Using a wide range of organic substrates in the methane fermentation process enables efficient biogas production. Nonetheless, in many cases, the efficiency of electricity generation in biogas plant cogeneration systems is much lower than expected, close to the calorific value of the applied feedstock. This paper analyses energy conversion efficiency in a 1 MWel agricultural biogas plant fed with corn silage or vegetable waste and pig slurry as a feedstock dilution agent, depending on the season and availability. Biomass conversion studies were carried out for 12 months, during which substrate samples were taken once a month. The total primary energy in substrates was estimated in laboratory conditions by measuring the heat of combustion in a ballistic bomb calorimeter (17,760 MWh·year-1), and in the case of pig slurry, biochemical methane potential (BMP, (201.88±3.21 m3·Mg VS-1). Further, the substrates were analysed in terms of their chemical composition — from protein, sugar and fat content to mineral matter determination, among other things. The results obtained during the study were averaged. Based on such things as the amount of biogas produced at the plant, the amount of chemical (secondary) energy contained in methane as a product of biomass conversion (10,633 MWh·year-1) was calculated. Considering the results obtained from the analyses, as well as the calculated values of the relevant parameters, biomass conversion efficiency was determined as a ratio of chemical energy in methane to (primary) energy in substrates, which was 59.87%, as well as electricity production efficiency, as a ratio of electricity produced (4,913 MWh·year-1) to primary energy, with a 35% cogeneration system efficiency. Full energy conversion efficiency, related to electricity production, reached a low value of 27.66%. This article provides an insightful, unique analysis of energy conversion in an active biogas plant as an open thermodynamic system.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

The optical complexity of coastal waters is mostly caused by the water discharged from land carrying optical components (such as dissolved and particulate matter) into coastal bays and estuaries, and increasing the attenuation of light. This paper aims to investigate the links between in-water optical properties in four Swedish bays (from the northern Baltic proper up to the Bothnian bay) and the land use and land cover (LULC) and the hydrology in the respective catchment of each bay. The optical properties were measured in situ over the last two decades by various research and monitoring groups while the LULC in each bay was classified using the Copernicus Land Monitoring Service based on Landsat 8 and Sentinel-3 data. The absorption coefficient of coloured dissolve organic matter at 440 nm, aCDOM (440), and its spectral slope factor, SCDOM, were mostly correlated to natural land cover classes (Wetland, Meadow) acting as sources of CDOM, while Agricultural and Urban classes seem to act as sinks. The Agricultural class was also found to be a sink for suspended particulate organic matter (SPOM) whilst Coniferous and Mixed Forests as well as Meadows acted as a sources. SPOM seems to mostly originate from Natural classes, possibly due to the release of pollen and other organic matter. Overall, the methods applied here allow for a better understanding of effects of land used and land cover on the bio-optical properties, and thus coastal water quality, on a macroscopic scale.

Strawberries (garden strawberries) belong to the most valuable berry crops and are an excellent dietary low-calorie product. This favorite berry is grown everywhere in Azerbaijan. The main objective of this study was a comparative study of 4 imported English strawberry cultivars Cupid, Fenella, Christine and Flamenco by productivity and its components, and on this basis, the selection of the most productive and adaptive. The study was conducted in a pilot production area (0.62 ha) of the Research Institute of Fruit and Tea Growing of the Ministry of Agriculture of the Azerbaijan Republic, which is located in the lowland part of the Guba district at an altitude of 400 m above sea level. Strawberry seedlings were planted on this site in the fall of 2020. The site was divided into paired rows repeated every 80 cm, and in each such pair the distance between the rows was 30 cm. The distance between the plants in each row was 15 cm. Mulching and drip irrigation were used as the main elements of the technology. When evaluating varieties by productivity in June 2022, when it reached its maximum level, the Fenella cultivar stood out. The productivity of this cultivar was 0.81 kg per bush or 40.2 tons per hectare. The same cultivar was distinguished by its large fruit (length 4.07 ± 0.42 cm, width 3.61 ± 0.55 cm, weight 20.96 ± 6.21 g), which indicates the prospect of its cultivation in the region.

Series of bifunctional catalysts, MoS2/Al2O3(70 wt.%)-zeolite (30 wt.%) (zeolite – ZSM-5, ZSM-12, ZSM-22 and silica aluminophosphate SAPO-11), were synthesized for hydroconversion of methyl palmitate (10 wt.% in dodecane) in a trickle-bed reactor. Mo loading was about 7 wt.%. Catalyst and supports were characterized by different physical-chemical methods (HRTEM-EDX, SEM-EDX, XRD, N2 physisorption, FTIR spectroscopy). Hydroprocessing was performed at temperature of 250-350°C, hydrogen pressure 3.0-5.0 MPa, liquid hourly space velocity (LHSV) 36 h-1, H2/feed ratio – 600 Nm3/m3. Complete conversion of oxygen-containing compounds was achieved at temperature 310°C in the presence of MoS2/Al2O3-zeolite catalysts, the selectivity for the conversion of methyl palmitate via the ‘direct’ hydrodeoxygenation (HDO) route was over 85%. The yield of iso-alkanes gradually increases in order: MoS2/Al2O3 &lt; MoS2/Al2O3-ZSM-12 &lt; MoS2/Al2O3-ZSM-5 &lt; MoS2/Al2O3-SAPO-11 &lt; MoS2/Al2O3-ZSM-22. The sample MoS2/Al2O3-ZSM-22 demonstrated the highest yield of iso-alkanes (40%). Hydroisomerization activity of the catalysts was in a good correlation with concentration of Brønsted acid sites of synthesized supports.

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

This study aims to evaluate the effect of different drying methodologies (room, microwave, convective, oven and freeze-drying) on the chemical composition, the microbiological quality of extracts and the biological activities namely clotting milk and antioxidant activities for both spontaneous and cultivated Onopordum nervosum ssp. platylepis. The results showed that the drying methodology has significantly affected the phenolic composition. Freeze dried flowers showed the best amounts of total phenols, flavonoids and condensed tannins followed by the microwave dried flowers. However, the latest presented the lowest protein content. Finally, the biological activities were significantly dependent on the used drying process. The effective concentration EC50 values let to classify the samples according to their decreasing power to inhibit DPPH free radicals: dryer<oven<room <microwave<freeze-drying. The drying process significantly affected the clotting milk activity, freeze dried flowers showed the highest activity. All the obtained results do not reveal a significant difference between cultivated and spontaneous plants.

The water quality index (WQI) and irrigational index for groundwater were studied in the northeastern section of the Manipur Valley in northeast India. Water samples were collected in 2022 during the pre-monsoon season. To compute the water quality index for drinking water, the basic chemical parameters of total hardness, pH, electrical conductivity, total dissolved solids, Ca2+, Na+, Fe, Mg2+, Mn, Cl-, and HCO3, were used. The assessment of bacteriological quality is also done, which is crucial for overall water quality evaluation, alongside physical and chemical analyze. For determining irrigation suitability, irrigational indices such as sodium absorption ratio, sodium percentage, and magnesium hazard were calculated. WQI, %Na+, SAR, magnesium hazard, permeability Index and total hardness indicate that most water samples are harmless for irrigation and drinking purpose. They have affirmative relationships indicating that these characteristics are interdependent. Approximately 25% of the Piedmont zone groundwater is found to be unfit for agricultural and drinking usage. The encrustation of gypsum, halite, and evaporation into the Disang shares accelerate the dissolution of ions in Piedmont water, resulting in quality degradation. According to Gibbs plots, Durov Scatter Plot, and Hill Piper Trilinear Diagram of water dominated the rock-weathering process, while hydro chemical facies progressed from the beginning to the intermediate stage of Chadha's graphical representation illustrates the progression of hydro chemical processes in surface water. Therefore, proper integrated water resource management and development are required for effective water resource utilization, particularly around the Piedmont zone. To prevent a water crisis, groundwater resources must be managed sustainably. The current study also concentrated on a bibliometric examination of groundwater management and access to gauge the state of the field.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources

With the development of bioinspired green solutions for sustainable construction over the past two decades, bio-cementation, which exploits the naturally occurring phenomenon of calcium carbonate precipitation in different environments, has drawn a lot of attention in both building construction and soil stabilization. Various types of microorganisms, along with specific enzymes derived from these microorganisms, have been utilized to harness the benefits of bio-cementation. Different application methods for incorporating this mechanism into the production process of the construction material, as well as a variety of experimental techniques for characterizing the outcomes of bio-cementation, have been developed and tested. Despite the success of bio-cementation as a sustainable method to construction has been demonstrated in a significant body of literature at the laboratory scale, the expansion of this strategy to construction sites and field application remains a pending subject. The issue may be attributed to two primary challenges. Firstly, the complexity of the bio-cementation phenomenon is influenced by a variety of factors. Secondly, the extensive body of literature examines various types of microorganisms under different conditions, leading to a wide range of outcomes. Hence, this study aims to examine the recent advancements in utilizing the most commonly employed microorganism, Sporosarcina Pasteurii, to emphasize the significance of influential factors identified in the literature, discuss the findings that have been brought to light, and outline future research directions toward scaling up the process.

This study examines the impact of weeds on sweet corn, where weeds compete with the main agricultural crops for essential elements such as nutrients, water, sunlight, and space for growth. In general. the use of herbicides is meant to suppress weed growth. Organic matter is important for plant growth and affects herbicide persistence. The study was aimed to explore the interdependence between ametryn herbicide and organic matter content and its impacts on weed growth, herbicide persistence, and sweet corn yield. The experiment was initiated in 2022 at the Experimental Station of the Faculty of Agriculture, Padjadjaran University, Indonesia, using a Split Plot Design in a Randomized Complete Block Design (RCBD) with three replicates. The experiments consisted of three levels of organic matter, i.e. low, medium, and high and 6 levels of ametryn herbicide at 0.0 (control), 0.5, 1.0, 1.5, 2.0, 2.5 kg a.i./ha. The results indicated that the apparent interdependence between ametryn herbicide doses of 1.5, 2.0 and 2.5 kg a.i./ha and the three levels of the organic matter content totally suppressed the weed growth. However, the effects of interdependence between ametryn herbicide and organic matter content on the herbicide persistence and on the sweet corn yield were not obvious. The ametryn herbicide gave excellent effects on sweet corn yield. Bioassay analysis showed that the lowest persistence of ametryn herbicide was in line with the highest content of the organic matter.

The production of oxygenated bio-additives for traditional fuels represents a key challenge due to the depletion of fossil fuels in the next future and their contribution to environmental pollu-tion. In this context, the present study considers the synthesis of different mixtures of 1-hexanol/hexyl hexanoate produced through the catalytic hydrogenation of hexanoic acid, a car-boxylic acid obtainable from the fermentation of a wide variety of waste biomasses. In particu-lar, crude hexanoic acid deriving from the fermentation of grape pomace, an abundant Italian agrifood waste, has been taken into consideration. The reaction was carried out with the com-mercial 5 wt% Re/γ-Al2O3 catalyst, whose acidity allowed the tuning of the reaction selectivity towards the preferential formation of hexyl hexanoate instead of 1-hexanol. As consequence, the tunable composition of the obtained 1-hexanol/hexyl hexanoate mixtures was leveraged for en-gine applications, thus allowing studying each component influence on the Diesel engine per-formances and verifying their synergistic effects. The engine experimental activity highlighted that both 1-hexanol and hexyl hexanoate, as well as their mixtures, can be used in Diesel engine with a commercial Diesel fuel up to high loadings (20 vol%) without altering engine perfor-mances and significantly lowering soot and CO emissions by more than 40%.

Alveolar bone atrophy after tooth extraction presents significant difficulties when planning delayed-immediate implant treatment to replace a lost tooth. Socket augmentation is an effective therapy that limits the post extraction volumetric changes and facilitates implant placement whilst reducing the need for staged grafting. However, socket augmentation and osteoconductive graft conversion is a slow process that could take 4-6 months. PRF and its variants have significant bio-enhancement effect on wound healing and regeneration through release of platelet drived growth factors, bioactive substances, cytokines. Leukocytes in PRF also play a significant role in enhancing tissue regeneration as part of osteo-immune response. Use of PRF during socket augmentation is highly effective in enhancing extraction site healing and graft integration by angiogenesis, cell proliferation, recruitment, and differentiation through release of growth factors and bioactive substances mediated by platelets and leukocytes. PRF with SA is recommended as an adjunct to SA as a sole biomaterial or in combination with xenograft or allograft bone substitutes to enhance tissue regeneration and to reduce risk of infection, osteitis and postoperative pain in extraction sockets

In this work, we report on the first attempt using size-controlled ZnO nanoparticles (NPs) to analyze role of thioacetamide (TAA) in forming ZnS nanostructures from ZnO. The size-controlled B(blue)_, G(green)_, Y(yellow)_ZnO QDs, and NC (nanocrystalline)_ZnO NPs were synthesized by sol-gel process as well as hydrothermal method, respectively and then reacted with an ethanolic TAA solution as sulfur source. After reacting with TAA, the formation of ZnS QDs was observed over time. The chemical reactions were identified using X-ray diffraction (XRD), Transmission Electron Microscope (TEM), UV-vis spectroscopy, and Photoluminescence (PL). All results indicate that ZnS formation is due to direct crystal growth and/or chemical conversion of ZnO to ZnS. Our results enable a broader understanding of the synthetic mechanisms involved in the use of TAA as a sulfur source in forming ZnS nanostructures from ZnO.

SiOx films, frequently derived from amino silane precursors, have found several applications with high added value. Although frequently used, the deposition of coatings from Tris(dimethyl amino)silane (TDMAS) has been reported to demand considerable amounts of energy, mainly due to the difficulty of oxidizing such compound. As it is well known, Plasma-enhanced atomic layer deposition (PEALD) is able to improve the oxidation efficiency even under low process temperatures. Owing to that, PEALD can be considered as a very promising technique for the deposition of SiOx coatings. In this work, it has been investigated the deposition of silicon oxide films using TDMAS at 150°C. It has been evaluated the effect of the plasma oxidation time (6 to 18 s) and of the atmosphere composition (pure O2 or O2+Ar) on the chemical structure, elemental composition and chemical bonding state of the films. Increasing the plasma oxidation time in pure O2 resulted in larger proportion of retained C (Si-CH3) whereas N was preserved in the structure (Si-N). on the other hand, the formation of SiOx films from TDMAS is favored in shorter oxidation times in O2 + Ar plasmas.

Ants have a very sophisticated olfactory system; their communication is based on the interpretation of chemical trails known as semiochemicals. The escamolera ant (Liometopum apiculatum), has behaviors and physiological responses is induced by semiochemicals, without however, these have not been studied. Using an electronic nose analysis (e-nose) and chromatographic techniques, semiochemicals of L. apiculatum in nests, foraging trails and dissected the gasters were evaluated. Data were analyzed with multivariate statistics and a logistic regression model based on predictors (ant counts) and the semiochemicals identified in pre-season (PRE), season (TEM) and post-season (POS) of larval collecting. From the general pattern of volatiles with a natural separation in POS and a partial distribution between PRE and TEM 32 semiochemicals were identified inside the nests, those who can induce the behavioral responses of trail-following, alarm, aggression, and nestmate recognition. Trail counts indicated that ant traffic was higher in POS and that the presence of certain semiochemicals (response variable) have good fit in the model regression. These findings are intended to provide useful information and support decision-making for the conservation and sustainable use of L. apiculatum in central Mexico.

The study investigated the chemical and functional characterization of propolis collected in southern Italy, in particular in Basilicata, a region rich in ecological and vegetative biodiversity. Sixteen samples of propolis, collected within a radius of 40 km from each other in the Basilicata region, showed significant differences between the chemical and functional parameters investigated: color index (L*, a*, b*; P<0.05), variation in chemical composition and antioxidant activities, by ABTS and FRAP assays. In general, Lucanian propolis had a low content of waxes (P<0.05) and a high content of resin (P<0.05) and balsams (P<0.05). The content of total phenolic compounds and flavonoids were highly variable, as was the biological capacity. In conclusion, Lucanian propolis showed a remarkable variability, highlighting a significant diversification according to the geographical position and the diversity of the flora surrounding the apiary of which the bees use as a source of resin. This study therefore contributes to the enhancement of the quality of propolis, laying the foundations for the production and marketing of propolis not only in the food industry, but also in the pharmaceutical and cosmetic industries.

The windowpane oyster Placuna placenta, lives in brackish coastal waters and has long been economically important to the Philippines because of its durable and translucent shell, which is used as a glass substitute and material for making windowpanes and handicrafts. There has been considerable degradation of the windowpane oyster fishery in past decades. Moreover, there are waste and under-exploited by-products such as the meat, which though nutritious and edible, currently has a very low value; its use being confined to dishes consumed by families in the fishing community. Historically there are instances of excellent practice in terms of regulating the windowpane oyster fishery, while in recent times there have been local initiatives to restore this and to develop high value food products from the meat. These initiatives have, however, never been followed through at a provincial or national level. Research on other molluscs and marine organisms highlights that these also contain high value pharmaceutical products. This review compiles evidence to establish the groundwork for an essential and comprehensive multidisciplinary research program centred around the windowpane oyster, which would ensure a high value for all parts of the oyster, including those currently discarded. By fostering a sustainable and circular economy within this fishery sector and its associated industry, its economic value would be amplified. This is particularly important for oyster harvesters in the Philippines, who often find themselves at the economic ladder's lower rungs. By integrating the principles of a circular economy, this initiative would not only aim to uplift the economic prospects of these harvesters but in doing so would drive the restoration of the windowpane oyster to its former range.

During the last forty years, the use of strontium isotopes in archaeology and biogeochemical research has spread widely. These isotopes, alone or in combination with others, can contribute to trace past and present environmental conditions. However, the interpretation of the isotopic values of strontium is not always simple and requires good knowledge of geochemistry and geology. This short paper on the use of strontium isotopes is aimed at those who use this tool (archaeologists, but not only) but who do not have a thorough knowledge of mineralogy, geology, and geochemistry necessary for a good understanding of natural processes involving these isotopes. We report basic knowledge and suggestions for a correct use of these isotopes. The isotopic characteristics of bio-assimilable strontium depend not so much on the isotopic characteristics of the bulk rock as, rather, on that of its more soluble minerals. Before studying human, animal and plant remains, the state of conservation and any conditions of isotopic pollution should be carefully checked. Samples should be collected according to random sampling rules. The data should be treated by a statistical approach. To make comparisons between different areas, it should be borne in mind that the study of current soils can be misleading since the mineralogical modification of the soil over time can be very rapid.

While biologic originators’ patents are expiring, biosimilars are emerging to take their place, offering significant cost savings to healthcare systems. Many challenges still need to be addressed in the clinical practice of inflammatory bowel disease (IBD). A global survey was organized to highlight physicians’ current knowledge and beliefs and to gain insight about their practical management and remaining concerns and obstacles associated with starting a biosimilar, switching from an originator to a biosimilar, or switching from one biosimilar to another (multiple switches and reverse switching). Fifteen physicians with expertise in the field of IBD from 13 countries attended a virtual international consensus meeting to develop practical guidance regarding biosimilar adoption worldwide, considering the survey results. Consensus was reached on 10 statements regarding biosimilar effectiveness, safety, indications and rationale, multiple switches, therapeutic drug monitoring of biosimilars, non-medical switching and future perspectives.

Monoterpenes as natural products are the subject of increased attention in the search for new pharmacological agents because of their numerous biological activities including antifungal, antibacterial, antioxidant, anticancer, antispasmodic, hypotensive, vasodilating effects, etc. In vitro and in vivo studies reveal their antidepressant, anxiolytic, and memory-enhancing in experimental dementia and Parkinson’s disease effects. Chemical modification of natural substances by conjugation with various synthetic components is a modern method of obtaining new biologically active compounds. The discovery of new potential drugs among monoterpene derivatives is a progressive direction in experimental pharmacology and a promising approach to the therapy of various pathologies. Biologically active substances such as monoterpenes borneol, camphor, geraniol, pinene, and thymol, were used to synthesize compounds with different properties, including analgesic, anti-inflammatory, anticonvulsant, anti-depressant, anti-Alzheimer’s, anti-parkinsonian, antiviral and antibacterial (anti-tuberculosis). Myrtenal is a perspective monoterpenoid with therapeutic potential in various fields of medicine. Its chemical modifications often lead to new or more pronounced biological effects. As an example, conjugation of myrtenal with the known pharmacophore adamantane allows one to enhance some of its key properties. Myrtenal-adamantane derivatives exhibited a variety of beneficial properties – antimicrobial, antifungal, antiviral, anticancer, anxiolytic, and neuroprotective, which are worth examining in more detail and at length.

Steady-state one-dimensional flows of five-component air behind a normal shock wave are considered with one-temperature model. A mathematical model is formulated to describe the relaxation of a five-component air mixture with a one-temperature non-equilibrium approximation. A numerical study of non-equilibrium flows of a reacting five-component air mixture behind shock waves at different heights and velocities of free flow is performed. The contribution of different types of reactions to the overall relaxation of the mixture is discussed, and the distributions of macro-parameters of the flow behind the shock wave front are calculated. The lengths of the relaxation zones behind the shock wave front are compared at different initial conditions.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

This review delves into the significance of chemical communication in mammals, with an emphasis on the role of the vomeronasal system in sensing pheromone-mediated interactions. The vomeronasal system shapes a variety of social and sexual behaviors, including reproduction, hierarchy formation, maternal bonding, and species recognition. Intriguingly, this system presents a vast degree of evolutionary variability, more so than variations observed in the olfactory system. This adaptive diversity underscores the challenges in studying the vomeronasal system, emphasizing the need for detailed research into its neuroanatomy and functional morphology. This review traverses an array of topics central to our understanding of chemical communication in mammals. We begin with the foundational role and basic concepts of chemocommunication. This is followed by an in-depth exploration of the olfactory systems. Subsequently, the neuroanatomical underpinnings of the vomeronasal system are juxtaposed against those of the olfactory system. Our focus then shifts to an exhaustive study of the sensory element of the vomeronasal system, the vomeronasal organ, and the integrating center of this information, the accessory olfactory bulb. The discussion extends to secondary projections of both the olfactory and vomeronasal systems in the light of the dual olfactory hypothesis. The review culminates with a detailed look at four specific models of vomeronasal system organization belonging to four evolutionarily distinct mammalian families: rodents, marsupials, herpestids, and bovids. These have been meticulously analyzed by the authors, aiming to spotlight the significant morphofunctional differences stemming from the adaptive changes imprinted on the system.

Stellatolides are natural compounds that have shown promising biological activities, including antitumor, antimicrobial, and anti-inflammatory properties, making them potential candidates for drug development. Chemical Reactivity Theory (CRT) is a branch of chemistry that explains and predicts the behavior of chemical reactions based on the electronic structure of molecules. Conceptual Density Functional Theory (CDFT) and Computational Peptidology (CP) are computational approaches used to study the behavior of atoms, molecules, and peptides. In this study, we present the results of our investigation of the chemical reactivity and ADMET properties of Stellatolides A-H using a novel computational approach called Conceptual DFT-based Computational Peptidology (CDFT-CP). Our study uses CDFT and CP to predict the reactivity and stability of molecules and to understand the behavior of peptides at the molecular level. We also predict the ADMET properties of the Stellatolides A-H to provide insight into their effectiveness, potential side effects, and optimal dosage and route of administration. This study sheds light on the potential of Stellatolides A-H as promising candidates for drug development and highlights the potential of CDFT-CP for the study of other natural compounds and peptides.

Mercury toxicity significantly threatens aquatic ecosystems, particularly impacting fish populations and human well-being. This article exposes the effects of mercury contamination on aquatic life and their habitats. Mercury primarily originates from natural degassing and anthropogenic activities and accumulates in aquatic organisms, most notably in predatory fish, through bio-accumulation and bio-magnification. This bio-accumulation, driven by microbial transformation to methyl-mercury, leads to elevated concentrations in top-level predators. The consequences of mercury exposure on fish physiology are stunted growth, reproductive impairments, and compromised immunity, with potential ramifications for population dynamics and ecosystem resilience. This study delves into specific impacts of mercury on fish, ranging from bone deformities to liver damage, developmental anomalies, neurotoxic effects, and disruptions in reproductive systems. The interplay between ecological, physiological, and human health effects underscores the need for a comprehensive understanding of mercury's underlying mechanisms. Monitoring mercury levels in aquatic systems emerges as a crucial strategy for ensuring fish populations' health and ecosystems' sustainability. Urgent collaborative efforts are imperative to address this global concern, promote harmonious coexistence between human activities and aquatic environments, and secure the availability of safe and nutritious fish for future generations. In conclusion, this article highlights the urgent necessity for targeted interventions and informed decision-making to mitigate the influence of mercury contamination on aquatic ecosystems.

Due to the low content, few studies are focused on the essential oils (EOs) of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (syn. Lamiophlomis rotata (Benth.) Kudô. This plant has been used to treat rheumatic arthritis and grasserie in China. However, such EOs may have important pharmacological activities such as anti-cancer. To identify the chemical markers (CM) in the EOs and evaluate their antioxidant activities (AAs), we firstly conduct a thoroughly investigation on their chemicals and AAs, to the best of our knowledge. Light yellow EOs with fresh and elegant smell are obtained by hydro-distillation with average yield 0.11% (volume mL/weight g). The crystals are separated from the EOs through cryoprecipitation, respectively. A total of 81 components are qualified and quantified in the EOs, crystals and EOs removed crystals, in which 44 ones are first reported. As for content, the main compounds are long-chain fatty acids (FAs) and their esters. The most abundant one n-hexadecanoic acid (palmitic acid, PA) accounting for 43.15-54.8%, 58.49-64.57% and 15.9-41.1%, in the EOs, crystals and EOs removed crystals, respectively. Seven compounds including PA, tetradecanoic acid, linoleic acid, oleic acid, methyl hexadecanoate, hexahydrofarnesyl acetone and phytol can be chosen a the CMs in these EOs. The AAs are evaluated through in vitro assays. PA presents pro-oxidant activities in a concentration dependence manner. Usually, the EOs removed crystals demonstrate stronger AAs, and the crystals demonstrate weaker AAs compared with that of the corresponding EOs, which is related to the different content of PA in these samples. This study can give some hints for the utilization of such EOs which are abundant in FAs such as PA.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, an-tioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 atmosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The an-tioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) charac-terized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in biochar, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydro-carbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil increase exponentially with molarity, while those of oxygenates de-crease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and decreases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

Diabetes mellitus is a widespread chronic metabolic disorder demanding regular blood glucose level surveillance (BGLs). Current invasive techniques, such as finger-prick tests, often result in discomfort for patients, leading to infrequent monitoring and potential health complications. The primary objective of this study was to design a novel, portable, non-invasive system for diabetes detection using breath samples, named as DiabeticSense, an affordable digital health device for early detection, encouraging immediate intervention. The device employed MOSFET-based electrochemical sensors to assess volatile organic compounds in breath samples, whose concentrations differ between diabetic and non-diabetic individuals. The system merged body vital signs with sensor voltages obtained by processing breath sample data to predict diabetic conditions. Our research used readings from 100 patients at a nationally recognised hospital to form the dataset. Data was then processed 10 using a Gradient Boosting Classifier model, and performance was cross-validated. The proposed system attained a promising accuracy of 86.6%, marking an improvement of 20.72% over an existing regression technique. The developed device introduces a non-invasive, cost-effective, and user-friendly solution for preliminary diabetes detection. It has the potential to increase patient adherence to regular monitoring.

Objective: This study aimed to validate the use of liquid phenol-based chemical peeling therapy for cervico-vaginal intraepithelial neoplasia (CIN and VaIN), with the goal of circumventing obstetric complications associated with surgical treatment. Methods: A total of 483 eligible women diagnosed with CIN and/or VaIN participated in this study. Participants underwent phenol-based chemical peeling therapy every 4 weeks until disease clearance. Disease clearance was determined by negative Pap tests for four consecutive weeks. HPV genotyping was conducted at the onset of the study and after disease clearance in select cases. Results: Among the 476 participants (excluding those with cancer), the number of treatment sessions until CIN/VaIN clearance ranged from 2 to 49 (median = 7 sessions). Forty-five participants (9.4%) underwent surgical treatments. Seven participants (1.5%) experienced recurrence, presenting with CIN2/VaIN2 or worse lesions; of these, three underwent LEEP, while four repeated the chemical peeling therapy. No obstetrical complications were noted among the 98 pregnancies following this therapy. The findings suggest that phenol-based therapy is safe and effective for CIN, although it requires numerous and lengthy treatments. Factors associated with resistance to this therapy include immune suppression, high-grade lesions, multiple HPV type infection, and direct or passive smoking.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

Coffee processing generates a huge amount of waste which contains many natural products. Here, we report the discovery of a panel novel cell-penetrating and metal-ion binding microproteins designated coffeetide cC1a-c and cL1-6 from the husk of two popular coffee plants, Coffea canephora and Coffea liberica, respectively. Combining sequence determination and database search, we showed that the prototypic coffeetide cC1a is a 37-residue, eight-cysteine microprotein with a hevein-like cysteine motif but without a chitin-binding domain. NMR determination of cC1a revealed a compact structure that confers it resistance to heat and proteolytic degradation. Disulfide mapping together with chemical synthesis revealed that cC1a has a ginsentide-like, and not a hevein-like, disulfide connectivity. In addition, transcriptomic analysis showed that the 98-residue micrcoproten-like coffeetide precursor contains a three-domain arrangement like ginsentide precursors. Molecular modeling together with experimental validation revealed a Mg2+ and Fe3+ binding pocket at the N-terminus formed by three glutamic acids. Importantly, cC1a is amphipathic with a continuous stretch of 19 apolar amino acids, and which enables its cell penetration to target intracellular proteins, despite being highly negatively charged. Our findings suggest that coffee by-products could provide a source of ginsentide-like bioactive peptides that have potential to target intracellular proteins.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

The aerospace industry demands high-performance materials that can withstand extreme conditions and maintain efficiency in a variety of applications. Bio-inspired polymer coatings have emerged as a promising approach to meet these demands, by drawing inspiration from natural systems to develop new coatings that exhibit enhanced properties, such as self-cleaning, anti-icing, thermal management, and corrosion resistance. In this review, recent developments in the field of bio-inspired polymer coatings for aerospace applications are presented, covering a range of coatings and their respective properties. We discuss the recent developments and applications of bio-inspired coatings, with a focus on their advantages and challenges in aerospace applications. We also highlight the potential for future research and development in this field, including the integration of advanced technologies such as nanotechnology and additive manufacturing. The review aims to provide insights into the current state-of-the-art of bio-inspired polymer coatings for aerospace applications and to inspire further research in this rapidly growing field.

As the human-body controls depend on the brain neuro current, here assay is related to thinking nerve detection. For this purpose, the brain current was analyzed by electrochemical three-electrode systems using 0.1-mm micro wire in vivo probe, which probe was made by using carbon nanotube paste coated needle type. Here working electrode was inserted in the rat brain’s muscle core with a 0.3-mm-diameter needle type Ag/AgCl Cl-coated Ag wire reference, and counter electrode of 0.1-mm-diameter Pt micro needle was inserted 5 mm deep into the in vivo muscle skin, under anesthesia with 2.0 ~ -2.0 V potential windows, 50 mv/s cyclic scan and 1.0x10-5A chrono amperometric sensitivity on the body systems. Under the optimum conditions, diagnostic application was performed to such as smell signal, muscular strength, five sense assay and thinking neuro current.

Due to the high impact of the building sector on the environment, a growing interest focuses on insulating materials able to ensure good thermo-acoustic performance for the building envelope, in a sustainable and circular economy perspective. In this context, Moroccan natural gypsum was mixed with natural waste local materials. Thermal and acoustic properties of the samples were measured; they were compared to those of synthetic- and mineral-based gypsum plasters, manufactured with the same technique. A Small Hot Box apparatus was used for thermal characterization, whereas acoustic performance was investigated by means of a Kundt’s Tube. Natural and synthetic additives involved a reduction in density and an improvement in thermal performance. Conductivity values in the 0.181 – 0.238 W/mK range were obtained, depending on the type of natural additive, with respect to 0.275 – 0.323 W/mK of mineral-based gypsum plasters. The acoustic measurements showed that all the composites have similar performance in terms of acoustic absorption, whereas high Transmission Loss values were obtained for the natural additives (TL = 35 – 59 dB). Petiol of Palm and Stipa Tenacissima were found as the materials able to improve both thermal and acoustic properties.

Abstract: The chemical mechanical polishing (CMP) has been widely used for surface modification of critical materials and components and provided global planarization of topography with a low post-planarization slope high quality and efficiency. The colloidal silica slurries play an important role in the finishing processes of optical components. Monodisperse mesoporous silica nanospheres were synthesized with different surfactant by Stöber method. Their architectural features and texture parameters were characterized by XRD, FTIR, N2 adsorption–desorption isotherms, SEM, XPS, and TGA techniques. The spherical SiO2 products presented with the controllable 50-150 nm particle size and distribution. The AFM micrographs reveal that flat and smooth surfaces without distinct scratches residual particles are achieved by using the as-obtained composite particles as abrasives[The particle size of SiO2 slurry plays a critical role in the chemical-mechanical polishing process.

An increase in Spodoptera species was reported in Bt soybean fields expressing Cry1Ac insecticidal proteins in Brazil, requiring additional management with chemical insecticides. Here, we evaluated the dose effects of flubendiamide and thiodicarb on Spodoptera cosmioides (Walker, 1858), Spodoptera eridania (Stoll, 1782), Spodoptera albula (Walker, 1857) and Spodoptera frugiperda (J. E. Smith, 1797) (Lepidoptera: Noctuidae) that survived on MON 87751 × MON 87708 × MON 87701 × MON 89788, expressing Cry1A.105, Cry2Ab2 and Cry1Ac; MON 87701 × MON 89788 soybean, expressing Cry1Ac; and non-Bt soybean. On unsprayed Cry1A.105/Cry2Ab2/Cry1Ac soybean, only S. frugiperda showed ~60% mortality after 10 d, whereas S. cosmioides, S. eridania and S. albula showed >81% mortality. Surviving larvae of all species on this Bt soybean showed &gt;80% mortality when exposed to the field label dose of flubendiamide (70 mL/ha) or thiodicarb (400 g/ha) or at 50% of these doses. In contrast, all four species had <25% and <19% mortality on Cry1Ac and non-Bt soybean, respectively. Surviving S. cosmioides, S. eridania and S. albula on these soybean types presented >83% mortality post-exposure to both dose levels of flubendiamide and thiodicarb. Some S. frugiperda larvae surviving on Cry1Ac and non-Bt soybean sprayed with a 50% dose of either insecticide developed into adults. However, L1 larvae developing on Cry1Ac soybean leaves sprayed with flubendiamide and L2 larvae on this soybean sprayed with thiodicarb had a prolonged immature stage, and females lower fecundity, which are likely to impact its population growth on soybean.

Inflammatory diseases are common pathological processes caused by various acute and chronic factors and some of them are autoimmune diseases. Exosomes are fundamental extracellular vesicles secreted by almost all cells, which contain a series of constituents, i.e. cytoskeletal and cytosolic proteins (actin, tubulin, histones), nucleic acids (mRNA, miRNA, DNA), lipids (diacylglycerophosphates, cholesterol, sphingomyelin, ceramide), and other bioactive components (cytokines, signal transduction proteins, enzymes, antigen presentation and membrane transport/fusion molecules, adhesion molecules). This review would be a synopsis of the actual knowledge on the contribution of exosomes from different cell sources as possible therapeutic agents against inflammation, focusing on several inflammatory diseases, neurological diseases, rheumatoid arthritis and osteoarthritis, intestinal bowel disease, asthma, liver and kidney injuries. Current knowledge indicates that the role of exosomes in therapy of inflammation and in inflammatory diseases could be distinctive. Main limitations to their clinical translation are still production, isolation, and storage. Additionally, there is an urgent need to personalize the treatments in terms of selection of exosomes, their dosages and routes of administration, and a deeper knowledge about their biodistribution, type and incidence of adverse events and long-term effects of exosomes. In conclusion, exosomes can very promising next generation therapeutic option, superior to synthetic nanocarriers and cell therapy, and can represent a new strategy of effective, safe, versatile and selective delivery systems in the future.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

Herein we report the expansion of the chemical space available from the chitin, accessible via the biogenic N-platforms 3A5AF, M4A2C and di-HAF. The biologically active heteroaromatics furo[3,2-d]pyrimidin-4-one and furo[3,2-d]pyrimidin-4-amine can be selectively accessed from 3A5AF and M4A2C, respectively. The chiral pool synthon di-HAF is a viable substrate for the Achmatowicz rearrangement, providing streamlined access to 2-aminosugars possessing a versatile hydroxymethyl group at C5.

Cheese whey, a significant byproduct of the dairy industry, poses a substantial environmental challenge due to its organic pollutant load and large size demands for effective and affordable valorization methods. The abundance of lactose and other organic compounds in whey contributes to its elevated Biological Oxygen Demand (BOD) and Chemical Oxygen Demand (COD), further straining natural ecosystems. This study aimed to investigate the nutritional potential of whey and its conversion into value-added products: bioethanol and probiotic drinks. To achieve this, Bacillus megaterium and Bacillus subtilis strains, isolated from soil samples in Nepal, were co-cultured with Lactobacillus and Saccharomyces cerevisiae in the whey broth for fermentation. Ethanol distillation was carried out using a Rota-evaporator to maintain the viability of the fermenting organisms within the broth. Moreover, the probiotic criteria of the fermenting strains were extensively examined. Experimental observations revealed a remarkable concentration of 9.2 g/L of ethanol, resulting in an ethanol yield of 0.23 g/L. Extrapolating this rate, it is theoretically possible to produce an annual global bioethanol output of 5 million tons using whey as a sustainable and abundant resource. Furthermore, the study explores novel advancements in the distillation process, demonstrating the successful extraction of ethanol at room temperature. Additionally, the fermentation organisms employed in this research exhibit robust viability, surviving various in-vitro stress-tolerant tests, including exposure to bile salt, pH fluctuations, and gastric juice. These resilient strains also demonstrated long-term stability in fermented whey broth, making them promising candidates for the development of probiotic beverages. This dual approach not only enables the sustainable management of organic waste but also presents an opportunity to create value-added products with positive implications for both the environment and human health.

The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry and high performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than that of the original biomass (higher heating value of Eucalyptus sawdust bio-oil 29 MJ/kg versus 19.5 MJ/kg of the original Eucalyptus sawdust). The analyses of the bio-oils allowed to identify the presence of high added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of the liquefied biomass showed that the biofuel density increases with the storage time due to the occurrence of repolymerization reactions.

Strontium (Sr) is a trace element in human body that able to promote bone formation and inhibit bone absorption. The conversion coating of strontium phosphate (Sr-P) on the surface of titanium (Ti) can improve its biological properties, and has a wide application prospect in the fields of dentistry and orthopedics. In this present study, Sr-P coatings with SrHPO4 and Sr3(PO4)2 crystals on Ti are prepared by phosphate chemical conversion (PCC) treatment. And the effect of pH on the properties of Sr-P coatings is researched. The results prove that phase composition, morphology and corrosion resistance of coated Ti are different with the pH values in PCC solution. The morphologies of conversion deposition on Ti change from plat-like to cluster-like, and then homogeneous microcrystals, as pH value changed from 2.50 to 3.25. Only discrete SrHPO4 crystals are generating on substrate at lower pH value, while relative stable Sr3(PO4)2 and SrHPO4 crystals are growing and subsequently forming an integrated coating on Ti as pH is higher than 2.50. The corrosion resistance of coated Ti improves comparing with that of bare Ti because of forming Sr-P coatings with Sr3(PO4)2 phase. In addition, it is indicated that the Sr-P coatings can improve the adhesion and differentiation of BMSCs.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Development and implementation of safe natural alternatives to synthetic pesticides are urgent needs that will provide ecological solutions for control of plant diseases, bacteria, viruses, nematodes, pests, and weeds, to ensure economic stability of the farmers and food security as well as protection of the environment and human health. Unambiguously, production of botanical pesticides will allow sustainable and efficient use of natural resources and finally decrease the use of chemical inputs and burden. This is underlined by the strict regulations on pesticide residues in agricultural products and harmonized with the Farm to Fork strategy aimed to reduce pesticide use by 55%, by 2030. Recognizing the urgent need for natural pesticides development, this work is an overview of the current research on the valorization of Mediterranean plants as potential source of biopesticides. More specifically, the extraction methods, the chemical composition, the biopesticidal activity, the commonly used assays for evaluating the antimicrobial, the pesticidal, the repellant and the herbicidal activity of plant extracts as well as toxicological and safety aspects of biopesticides formulation are discussed in detail. Finally, the aspects that have not yet been investigated or are under- investigated and future perspectives are highlighted.

Amidst the strong demand for wood-based products, and the clamor of environmental consciousness, more functional and green solutions arise to meet both of these goals. Pursuant to this, the study looked into the potential of a bio-waste taken from Cocos nucifera tree known as phellem—the tree’s outermost skin made of dead tissues, to be a main component of a new construction material. This study builds on existing research showing phellem is impermeable, buoyant, elastic, has a slow burn rate, and repels water during precipitation, which supports the hypothesis that phellem may be a potential substitute material for dry wall boards. To test this, three (3) formulations were developed as experimental setups to test the physico-mechanical properties of coconut palm phellem (COPAP): Formulation A (40% COPAP and 60% cement); Formulation B ( 25% COPAP and 75% cement); and lastly, Formulation C that was (10% COPAP and 90% cement). The study tested (1) which among these formulations exhibited the best physico-mechanical properties, then it (2) compared the formulations with common dry wall products available in the market, and subsequently, (3) identified the possible architectural applications of COPAP board as a new building material. Of the three setups, Formulation C exhibited the best physico-mechanical properties in terms of compressive and flexural strength, fire resistivity, and water absorption. It fared better than the particle board in terms of compressive strength, better than wafer and particle board in fire resistivity, performed best in the water absorption test, and was almost equivalent in flexural strength to fiber cement board. With these findings, the study concluded that COPAP board can be used for projects that entail a high number of interior partitions, such as offices, BPO firms and commercial stalls in shopping malls, etc. The findings were conclusive only for interior applications, as the results clearly suggest that the COPAP boards are not load-bearing. Future investigations may explore and assess other properties of COPAP boards like thermal and sound insulation, resistance to rot and other properties that may prove its competitive advantage as a construction material.

Bisphenol A (BPA) has been identified as one of endocrine disrupting chemicals (EDCs). Due to its massive production (over 700,000 tons per year) and the extensive use of BPA-based plastics (i.e., polycarbonate and epoxy resin) in Taiwan, it was thus included into a toxic substance by the Ministry of Environment. This work surveyed the updated information about the production of BPA and its environmental distributions in Taiwan over the past decade. Furthermore, the regulatory strategies and countermeasures for managing the environmental risks of BPA by the Taiwan government were summarized to show the cross-ministerial efforts under the relevant acts, including the Toxic and Concerned Chemical Substances Control Act (TCCSCA), the Food Sanitation Management Act (FSMA) and the Commodity Inspection Act (CIA). The findings showed that most of the monitoring data showed far below the acceptable risks. However, the people may pose an adverse threat to the aquatic environment and human health via ecological and food chains. In addition, some countermeasures were further recommended to echo the international actions on environmental endocrine disruptors in recent years.

This research presents a novel approach for estimating soil organic carbon (SOC) content in agricultural soils using a photocatalytic Chemical Oxygen Demand (PeCOD) analyzer integrated with Geographic Information System (GIS) technology for spatial analysis. The PeCOD method, which relies on photochemical oxidation of organic carbon, demonstrated an uncanny correlation between its values and SOC content, making it a quick and accurate way to estimate SOC levels. Finer materials, such as clayey soils, demonstrated higher SOC content compared to coarser ones and decreased with increasing soil depth. GIS georeferencing enabled precise mapping of SOC distribution and identification of hotspot areas with high SOC content. This study highlights the significance of soil texture and depth on SOC distribution and emphasizes its significance within geological context when studying soil properties. Research results have practical ramifications for sustainable agriculture, climate change mitigation and soil health management - providing farmers and land managers with strategies that increase carbon sequestration while simultaneously improving soil health. Integrating PeCOD analyzer technology with GIS technology offers promising avenues for advanced soil carbon monitoring practices that promote climate-smart agricultural practices.

The aim of the study was to verify whether a reduced nitrogen (N) fertilization rate according to the EU recommendation (“From field to table” directive) may guarantee good yields and will be sufficient to maintain soil fertility in monoculture maize cultivation in the no-tillage (NT) system versus the traditional plowing (P) system. Two fields (10 ha each) were established for P and NT maize cultivation where the following N doses were applied: 0.0; 69.0, 92.0, and 115.0 kg ha-1. Soils (0-20 cm) were sampled two times per year - in spring (before maize sowing) and in autumn (after maize harvesting). A broad range of chemical (reaction, water holding capacity, total and easily degradable carbon, ammonium, nitrates, magnesium, calcium, potassium, sulfur) and biological (respiration, humic acids) parameters were monitored during the experiment. The vast majority of these factors had higher values in autumn than in spring. Although the role of reduced fertilization was not shown to be significant, the correlation analysis revealed some relationships between yield and nutrient availability. The 20% reduction in N fertilization does not have an adverse effect on the chemistry and biological characteristics of soils and does not worsen their chemical and biological quality.

In the production of grafted vines, losses are caused by fungal pathogens during callus forming or after planting in the soil. To control or reduce natural fungal infections in nurseries, certain applications were conducted in sapling cultivation stage to analyse the efficacy of cyprodinil + fludioxonil, floupyram + tebuconazole active substances and Trichoderma harzianum biological preparation. 1103 Paulsen rootstock and Vitis viniferea L. Sultana cultivars were stored in fungicide suspensions for 60 minutes before and after grafting in the study. After grafting, the seedlings were divided into i) cutting + sawdust ii) cutting + sawdust + soil application groups and transferred to the callus room. Fungicides were applied 1 to 7 days after the callus development to wet the seedling roots 1 to 7 days after they were planted. After nine months in the nursery, the plants were uprooted, classified as diseased or healthy, and analysed for morphological and molecular diagnosis of fungal species, isolation incidence, and seedling quality and yield. After callus development, Fusarium solani was most frequently isolated pathogen in the roots (21.5%), cyprodinil + fludioxonil reduced the Ilyonectria sp. isolation rate in both shoots and roots. Botryosphaeria obtusa and I. liriodendri pathogens were not detected in sick and healthy cyprodinil + fludioxonil-treated saplings. The highest seedling yield was observed with fludioxonil + cyprodinil, cutting + sawdust + soil (78.75%) and cutting + sawdust (70.68%) applications. According to the results of this study, it was found that fungicide applications before and after grafting prevented soil-borne pathogen infections and improved sapling quality.

This study explores the impact of temperature and molarity on the pyrolysis of Açaí seeds (Euterpe Oleraceae, Mart.) activated with KOH on the yield of bio-oil, hydrocarbon content of bio-oil, antioxidant activity of bio-oil and chemical composition of aqueous phase. The experiments were carried out at 350, 400, and 450 °C and 1.0 atmosphere, with 2.0 M KOH, and at 450 °C and 1.0 at-mosphere, with 0.5 M, 1.0 M and 2.0 M KOH, in laboratory scale. The composition of bio-oils and aqueous phase determined by GC-MS, while the acid value, a physical-chemical property of fundamental importance in biofuels, of bio-oils and aqueous phases by AOCS methods. The antioxidant activity of bio-oils determined by the TEAC method. The solid phase (biochar) characterized by X-ray diffraction (XRD). The diffractograms identified the presence of Kalicinite (KHCO3) in bio-char, and those higher temperatures favor the formation peaks of Kalicinite (KHCO3). The pyrolysis of Açaí seeds activated with KOH show bio-oil yields from 3.19 to 6.79 (wt.%), aqueous phase yields between 20.34 and 25.57 (wt.%), solid phase yields (coke) between 33.40 and 43.37 (wt.%), and gas yields from 31.85 to 34.45 (wt.%). The yield of bio-oil shows a smooth exponential increase with temperature. The acidity of bio-oil varied between 12.3 and 257.6 mgKOH/g, decreasing exponentially with temperature, while that of aqueous phase between 17.9 and 118.9 mgKOH/g, showing and exponential decay behavior with temperature, demonstrating that higher temperatures favor not only the yield of bio-oil but also bio-oils with lower acidity. For the experiments with KOH activation, the GC-MS of bio-oil identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, cycloalkenes, and aromatics) and oxygenates (carboxylic acids, phenols, ketones, and esters). The concentration of hydrocarbons varied between 10.19 to 25.71 (area.%), increasing with temperature, while that of oxygenates from 52.69 to 72.15 (area.%), decreasing with temperature. For the experiments with constant temperature, the concentrations of hydrocarbons in bio-oil in-crease exponentially with molarity, while those of oxygenates decrease exponentially, showing that higher molarities favor the formation of hydrocarbons in bio-oil. The antioxidant activity of bio-oils decreases with increasing temperature, as the content of phenolic compounds decreases, and de-creases with increasing KOH molarity, as higher molarities favors the formation of hydrocarbons. Finally, it can be concluded that chemical activation of Açaí seeds with KOH favors the not only the yield of bio-oil but also the content of hydrocarbons. The study of process variables is of utmost importance in order to clearly assess reaction mechanisms, economic viability and design goals that could be derived from chemically activated biomass pyrolysis processes.

This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.