Antioxidants reduce arterial stiffness but the effects previously reported are weak. The present study evaluated the effects of 2 weeks of therapy with a combination of antioxidants (l-cysteine, thiamine, pyridoxine and ascorbic acid) compared to placebo on stiffness index (SI) a measure of arterial stiffness that is strongly correlated with central pulse wave velocity (PWV), using a Pulse Trace recorder in a diverse group of 78 volunteers. SI fell by 1.7 m/sec relative to placebo (95% confidence intervals 0.6 to 2.7 m/sec), a reduction of 19% (95% confidence intervals 9% to 31%). The Glass effect size was 1.4, indicating a very strong treatment effect which was substantially greater than found in previous studies of the effects of antioxidant therapy on arterial stiffness. The magnitude of reduction in SI was positively correlated with increasing age (r = 0.362 P = 0.02). The change in RI, a measure of compliance of small to medium size arteries, did not differ between the antioxidant and placebo groups The combination of antioxidants studied reduced PWV to a much greater extent than reported for other antioxidants. This combination may be of value in the treatment of cardiovascular disease.

An analysis of the stiffness theory reveals that coal mass compression bumps occur only when both the failure criterion and the stiffness criterion are simultaneously satisfied. Then a new structural factor called uneven stiffness coal seam structure (USCS) is proposed, which consists of an uneven stiffness coal seam along with continuous roof and floor. The USCS serves the dual functions of pressure concentration and stiffness reduction. The former facilitates stress concentration from the low stiffness zone (LSZ) to the high stiffness zone (HSZ), thus raising the risk (rF) of failure. The latter reduces the stiffness of the surrounding rock of the HSZ, allowing the system to meet the stiffness criterion even with a hard roof, thereby reconciling the contradiction between the stiffness theory and engineering experience and raising the risk (rI) of instability. The HSZ of the USCS, including thinning zones, bifurcating areas, magmatic intrusion areas, and remnant pillar affected areas, is more susceptible to coal bump incidents than a conventional coal seam. Mechanical analysis and simple numerical simulations validate the pressure concentration and stiffness reduction functions of the USCS. The results demonstrate the following: 1) The normal stress of the HSZ positively correlates with ER, HR, KH, and SL, but negatively correlates with KL and SH; The stiffness of surrounding rock of the HSZ negatively correlates with HR, KH, SL, and SH, but positively correlates with ER and KL. 2) Failures within the HSZ of the USCS enables the roof strata to release bending deformation energy without undergoing fracturing. 3) The alignment between the HSZ of an existing USCS and the HSZ of an artificial USCS advancing with the working face intensifies stress concentration and reduces stiffness, thereby significantly increases the risk (rCB) of coal bump. By applying the stiffness theory and relevant USCS findings, new explanations can be provided for engineering phenomena such as the time-delayed coal bumps, the inefficient pressure relief in ultra thick coal seams, and the “microseism deficiency” observed prior to certain coal bumps.

The corrugated board packaging industry is increasingly using advanced numerical tools to design and estimate the load capacity of its products. That is why numerical analyzes are becoming a common standard in this branch of manufacturing. Such trend causes either the use of advanced computational models that take into account the full 3D geometry of the flat and wavy layers of corrugated board, or the use of homogenization techniques to simplify the numerical model. The article presents theoretical considerations that extend the numerical homogenization technique already presented in our previous work. The proposed here homogenization procedure also takes into account the creasing and / or perforation of corrugated board, i.e. processes that undoubtedly weaken the stiffness and strength of the corrugated board locally. However, it is not always easy to estimate how exactly these processes affect the bending or torsional stiffness. What is known for sure is that the degradation of stiffness depends, among other things, on the type of cut, its shape, the depth of creasing, as well as their position or direction in relation to the corrugation direction. The method proposed here can be successfully applied to model smeared degradation in a finite element or to define degraded interface stiffnesses on a crease line or a perforation line.

The stiffness of the myosin cross-bridges is a key factor in analysing possible scenarios to explain myosin head changes during force generation in active muscles. The seminal study of Huxley and Simmons (1971: Nature 233: 533) suggested that most of the observed half-sarcomere instantaneous compliance (=1/stiffness) resides in the myosin heads. They showed with a so-called T₁ plot that, after a very fast release, the half-sarcomere tension reduced to zero after a step size of about 60Å (later with improved experiments reduced to 40Å). However, later X-ray diffraction studies showed that myosin and actin filaments themselves stretch slightly under tension, which means that most (at least two-thirds) of the half sarcomere compliance comes from the filaments and not from cross-bridges. Here we have used a different approach, namely to model the compliances in a virtual half sarcomere structure in silico. We confirm that the T₁ curve comes almost entirely from length changes in the myosin and actin filaments, because the calculated cross-bridge stiffness (probably greater than 0.4 pN/Å) is higher than previous studies have suggested. In the light of this, we present a plausible modified scenario to describe aspects of the myosin cross-bridge cycle in active muscle. In particular, we suggest that, apart from the filament compliances, most of the cross-bridge contribution to the instantaneous T₁ response comes from weakly-bound myosin heads, not myosin heads in strongly attached states. The strongly attached heads would still contribute to the T₁ curve, but only in a very minor way, with a stiffness that we postulate could be around 0.1 pN/Å, a value which would generate a working stroke close to 100 Å from the hydrolysis of one ATP molecule. The new program can serve as a tool to calculate sarcomere elastic properties for any vertebrate striated muscle once various parameters have been determined (e.g. tension, T₁ intercept, temperature, X-ray diffraction spacing results).

Background: This study aimed to contribute to the standardization of elastography by comparing stiffness values obtained from ultrasound elastography (US-E) and magnetic resonance elastography (MR-E) of the testicular parenchyma in healthy subjects. Methods: A total of 22 healthy volunteers (44 testes) were included in this study. Of the 26 cases analyzed, four were excluded from the study due to the exclusion criteria. The testicular parenchyma of the included patients was evaluated using MR-E and Shear-Wave Ultrasound Elastography (SW-E) examinations. Pearson's correlation test was used to calculate the correlation between age and stiffness values, testicular volumes and stiffness values, and stiffness values from both examinations. Results: The mean US-E stiffness of the right testes was 5.560 ± 3.1 kPa and the mean US-E stiffness of the left testes was 5.361 ± 2.9 kPa. The mean MR-E stiffness of the right testes was 6960.11 ± 460 Pa and the mean MR-E stiffness of the left testes was 6560.19 ± 310 Pa. There was no significant correlation between US-E and MR-E stiffness values (p=0.096). There was also no significant statistical correlation between US-E and MR-E stiffness values and testicular volumes (p=0.17 and p=0.093). Conclusions: No statistical correlation was found between the stiffness values obtained by SW-E and those obtained by MR-E in the normal testicular parenchyma. Additionally, no conclusive relationship between stiffness levels, age, or testicular volume was discovered.

The geotechnical characterisation of offshore wind farm sites requires measurement or estimation of the small-strain shear stiffness Gmax of the subsoil. This parameter can be derived from shear wave velocity Vs measurements if the bulk density of the soil is known. Since direct measurements of Vs are generally not available at all foundation locations in a wind farm, CPT-based correlations are often used to determine location-specific stiffness parameters for foundation design. Existing correlations have mostly been calibrated to onshore datasets which may not contain the same soil types and stress conditions found in the North Sea. The distinct geological history of the North Sea necessitates a critical review of these existing CPT-based correlations. They are evaluated against an extensive database of in-situ Vs measurements in the Southern North Sea. The importance of modelling the stress-dependent nature of Vs is highlighted and a novel stress-dependent model for Vs from CPT data is presented. As the small-strain stiffness is used as an input to foundation response calculations, the model uncertainty of the correlation can introduce significant uncertainty in the resulting foundation response. This transformation uncertainty is quantified for each of the correlations evaluated in this study and shows important variations.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

This study presents a comprehensive investigation on an innovative mechanical system inspired by recent advancements in metamaterials, more specifically the work is focused on Origami-type structures for their intriguing mechanical properties. Originating from the specific fields such as aerospace for their lightweight and foldable characteristics, Origami mechanical devices exhibit unique non-linear stiffness, in particular, when suitably designed, they show Quasi-Zero Stiffness (QZS) characteristics within a specific working range. The QZS property, aligned with the High Static Low Dynamic (HSLD) stiffness concept, suggests promising applications such as a low-frequency mechanical passive vibration isolator. The study explores the vibration isolation characteristics of Origami-type suspensions, with a particular emphasis on their potential application as low-frequency passive vibration isolators. The Kresling Origami Module (KOM) has been selected for its compactness and compatibility with 3D printers. A detailed analysis using 3D CAD, Finite Element Analysis, and experimental testing have been carried out. The investigation includes the analysis of the influence of geometric parameters on the non-linear Force-Displacement curve. Multibody simulations validate the low-frequency isolation properties within the QZS region, and disparities in dynamic properties beyond the QZS range. The study underscores the transformative potential of Origami-type metamaterials in enhancing low-frequency vibration isolation technology. It also highlights challenges related to material properties and loading mass variations, providing valuable insights for future developments in this promising field.

The implementation of a progressive rehabilitation training model to promote patients’ motivation efforts can greatly restore the damaged central nervous system function in patients. The patients’ active engagement can be effectively stimulated by assist-as-needed (AAN) robot rehabilitation training. However, its application in robotic therapy has been hindered by a simple determination method of robot assisted torque which focuses on the evaluation only of the affected limb's movement ability. Moreover, the expected effect of assistance depends on the designer, which deviates from the patient's expectations, and its applicability to different patients is deficient. In this study, we propose a control method with personalized treatment features based on the idea of estimating and mapping the stiffness of the patient’s healthy limbs. This control method comprises an interactive control module in the task-oriented space based on the quantitative evaluation of motion needs and an inner loop position control module for the pneumatic swing cylinder in the joint space. An upper limb endpoint stiffness estimation model is constructed and a parameter identification algorithm is designed. The upper limb endpoint stiffness which characterizes the patient's ability to complete training movements is obtained by collecting surface electromyographic (sEMG) signals and human-robot interaction forces during patient movement. Then the motor needs of the affected limb when completing the same movement are quantified based on the performance of the healthy limb. A stiffness mapping algorithm is designed to dynamically adjust the rehabilitation training trajectory and auxiliary force of the robot based on the actual movement ability of the affected limb, achieving AAN control. Experimental studies were conducted on a self-developed pneumatic upper limb rehabilitation robot, and the results showed that the proposed AAN control method can effectively estimate the patient's movement needs and achieve progressive rehabilitation training. The rehabilitation training robot that simulates the movement characteristics of the patient's healthy limbs drives the affected limb, making the intensity of the rehabilitation training task more in line with the patient's pre-morbid limb use habits, and also beneficial for the consistency of bilateral limb movements.

In this paper, we present the design, manufacturing and characterization of a soft textile-based clutch (TBC) that switches between locking and unlocking of its linear displacement by exploiting vacuum stimulation. The applied vacuum locks the relative sliding motion between two elaborated textile webbings covered by an elastic silicone rubber bag. Based on different fabrication techniques, such as silicone casting on textile, melt embossing for direct fabrication of miniature patterns on textile and sewing, we developed three groups of TBC samples based on friction and interlocking principles and we compared their performance in blocking configuration. The clutch with interlocking mechanism presented the highest withstanding force (150 N) respect to the one (54 N) recorded for the friction-based clutch. The simple and compact structure of the proposed clutch, together with the intrinsic adaptability of fabric with other clothing and soft materials, make it a proper solution for applications in soft wearable robotics and generally as locking and variable stiffness solution for soft robotic applications.

The effect of contamination of polypropylene (PP) with selected polymers is studied to simulate the effect of mis-sorting in recycling streams. Polystyrene (PS), polyethylene terephthalate (PET), polycarbonate (PC), acrylonitrile-butadiene-styrene (ABS) and polylactic acid (PLA) were compounded with PP at different concentrations varying between 3 and 10%. Infrared spectroscopy proved the absence of chemical bonds between the constituents. The samples for mechanical testing were injection moulded and further tested for their tensile and impact properties. Critical behaviour was induced by the introduction of a weld line as a result of the application of multiple gating points during injection moulding. Results generally show the applicability of PP mixtures within the investigated range of inclusions, without much sacrifice in mechanical performance. However, in the case of ABS and PLA, more care should be taken when designing complex parts with weld lines, due to reduced toughness.

Considering the age of the dogs, it was expected that elderly animals would have stiffer thyroids than adults. The aim of this study was to evaluate the thyroid glands of healthy dogs using 2D shear wave elastography in order to establish qualitative and quantitative parameters of tissue stiffness in dogs of different age groups. The B-mode ultrasound and elastography findings were correlated with the weight and sex of the patients, allowing a reference range to be established for different groups of dogs. 31 dogs of different breeds, sexes and sizes were evaluated. Animals with clinical signs or ultrasound findings indicative of endocrine disease or thyroid lesions were not included in the study. Using QelaXtoTM 2D software, shear wave velocity data in m/s and color elastograms were evaluated and calculated. A healthy thyroid has a blue color elastogram, indicative of low stiffness, and there was no distinction between adult and elderly dogs, genders or sizes. The reference range for the shear wave velocity of thyroid tissue assessed by 2D shear wave elastography can be between 1.6 and 2.0 m/s with a variation of ±0.889 in adult and elderly dogs.

AFM nanoindentation showed variation in stiffness (Elastic modulus) due to heterogenous nature of the collagen fibres. The S values varied from 5 N/m to 11.11 n/m corresponding to an E change of 2.25 to 1.38 GPa. The variation in effective modulus (Eff) with respect to displacement indicated crossing the parabolic limit. A softening index n was proposed due to the heterogenous behaviour of the biomaterials

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

: Shear-wave elastography (SWE) has become popular in clinical practice for many diseases.However, there are not adequate research for spleen-related diseases.This study aimed to investigate the potential of quantitative values obtained through SWE in evaluating spleen pathologies in the pediatric population and to demonstrate its perfomance to differentiate splenomegaly-related diseases.Research group retrospectively included children with pathological diagnoses related to spleen from November 2016 to April 2021 and they were categorized three groups as portal hypertension (PH), benign lymphoid hyperplasia (BLH), malignant infiltration (MI).Spleen sizes and parenchymal stiffness were also calculated for each group.Subsequently, mean spleen stiffness in each compared with normal values within the same age group.In total 2781 children (1379 children for study group, 1402 children for control group) were enrolled to the study.The highest stiffness were observed in the PH group, which is statistically higher than others (p<0.05). Although the mean spleen stiffness in the group with BLH was higher than the control and MI group, the difference was not statistically significant (p=0.08).The mean stiffness in the group with MI was significantly lower than both the control group (p=0.005) and PH (p=0.01).In conclusion, using SWE in the differential diagnosis of etiologies causing splenomegaly, could make important contribution.

Background: Heart failure with preserved ejection fraction (HFpEF) is a major health concern. There is a growing recognition of the causal interplay between arterial stiffness and HFpEF. We recently reported that phosphate retention is a trigger for arterial stiffness. This study focuses on whether arterial stiffness due to phosphate retention could be a predictor for HFpEF. Methods: The study subjects were 158 patients (68 males and 90 females, mean age 74.8±11.2). HFpEF was defined according to the guidelines of the ESC 2019. Pulse wave velocity (PWV) and central systolic blood pressure (CSBP) were used as markers for arterial stiffness and afterload, respectively. We measured serum levels of fibroblast growth factor 23 (FGF23) as a marker of phosphate retention. Results: The serum levels of FGF23 had significant relationship with PWV. PWV had significant relationships with LV mass index, plasma BNP levels, and relative wall thickness, e’ and E/e’ (p<0.001, respectively). Multivariate logistic regression analysis revealed that PWV higher values and hypertension were significant predictors for the dependent factor (HFpEF). Conclusions: Arterial stiffness amplified LV afterload, leading to LV concentric hypertrophy and LV diastolic dysfunction. This study presents that arterial stiffness due to phosphate retention, and hypertension are important predictors of HFpEF.

Alginate-gelatin (Alg-Gel) hydrogels have been used experimentally but not clinically associated with mesenchymal stromal / stem cells (MSCs) to guide bone tissue formation. One of the main challenges for its clinical application is optimizing Alg-Gel stiffness to guide osteogenesis. In this study, we investigated how Alg-Gel stiffness could modulate the dental pulp stem cell (DPSCs) attachment, morphology, proliferation, and osteogenic differentiation, identifying the optimal condition to uncouple osteogenesis from the other cell behaviors. An array of Alg-Gel hydrogels was prepared by casting different percentages of Alg and Gel being crosslinked with 2 % CaCl2. We selected two hydrogels, one with 11± 1 kPa called “low” stiffness and one with 55 ± 3 kPa called “high” stiffness. Hydrogel analyses showed that the average swelling rates were 20 ± 3% for low and 35 ± 2% for high hydrogels. The degradation percentage was 47 ± 5% and 18 ± 2% for low and high hydrogels, respectively. Both hydrogel types showed homogeneous surface shape and pro-tein (Alg-Gel) interaction with CaCl2 as assessed by FTIR-ATR and XPS. Cell culture showed good adhesion of the DPSCs to the hydrogels and proliferation. Furthermore, better osteogenic activity was obtained with high-stiffness hydrogels. In summary, this study confirms the possibility of characterizing and optimizing the stiffness of alginate-gelatin gel to guide osteogenesis in vitro without altering other cellular properties of DPSCs.

Lower extremity joint kinetic factors are thought to modulate walk–to–run transition (WRT) and run–to–walk transition (RWT). This study aimed to investigate joint stiffness and energetic patterns during the WRT and RWT processes and identify whether gait transitions occurred within a single step or not. Ten healthy subjects participated in treadmill WRT (1.8 m/s – 2.4 m/s) and RWT (2.4 m/s – 1.8 m/s) tests. We investigated two steps before transition (S–2, S–1), two steps after transition (S1, S2) and the transition step (S0). We found significant differences between S2 and S–2 for ankle joint stiffness during WRT and RWT (p &lt; 0.001); and for hip joint stiffness, we found significant differences between S1 and S–1 during WRT and RWT (p ≤ 0.001). Additionally, stance phase mechanical energy generation was observed to transfer from proximal to distal joints at S0 during WRT, and from distal to proximal at S0 during RWT. Transition step ankle kinematic and kinetic patterns were similar to the target locomotion task gait format in both WRT and RWT. Moreover, RWT required longer adaptation time compared with WRT. These findings indicate that WRT and RWT were modulated before and after the actual transitions, not within a single step. Redistribution of joint mechanical work generation was related to gait transition triggers, which modulate the WRT and RWT process.

In order to improve the stiffness of the flexible robot,this paper proposes a variable-stiffness elastic actuator to improve the rigidity of flexible robots. The actuator integrates the working principles of a pneumatic drive, wedge structure, and particle blockage. the tensile stiffness of the actuator is nonlinearly negatively correlated with the air pressure because of the structural and material properties.The compressive stiffness and lateral stiffness increases nonlinearly as air pressure increases, being 3and 121 times greater at 0.17 MPa compared to 0 MPa, respectively. Beyond 0.17 MPa, the two stiffness of the actuator experiences incremental growth due to wedge impedance forces.

In view of the floating rectangular aerostatic guideway problem of low load capacity and stiffness, this paper puts forward a kind of closed rectangular aerostatic guideway and its optimized design. Firstly, the analytic calculation formula of a closed rectangular aerostatic guideway was deduced. The use of MATLAB software for the numerical simulation and the parameter influence analyses was carried out in terms of the gas supply pressure on load capacity and stiffness. A simulation model of the rectangular air bearing was also built using the Fluent software, and the model was used for simulation calculations. Secondly, the static performance of the rectangular air bearing was analyzed by analyzing the distribution position and number of orifices on its load capacity and stiffness. On this basis, the response surface optimization design method is used to analyze the variation law of the load capacity and stiffness of the air bearing under different restrictor structural parameters. Finally, the optimal design parameters for the rectangular air bearing are obtained. The simulation results show that the optimized rectangular air bearing designed in this paper has a good load capacity and stiffness of 644.58N and 63.405N N∙μm^(-1).

The rapid introduction of DAAs has revolutionized the treatment of chronic HCV infection, however some concerns have been arose about their early and long term safety in real life settings. Therefore, these drugs achieve a robust and sustained virological response in a short duration of treatment, being a quick winning option, but, what then? At now an extensive follow-up in real life settings does not exist particularly on HCC occurrence as recently suggested in a Cochrane review . In this regard from February 2015 to December 2017 a group of 5 Hospital and Academic Centers in Southern Italy (Campania Region) managed an observational, prospective, real-life study on efficacy and safety of DAAs treatment schedule enrolling 1022 consecutive HCV patients treated with IFN-free DAAs regimens being followed-up for 24 months. Our preliminary data on the first 360 patients out of 1022 whose completed at least 66 weeks follow-up, based on clinical, laboratory and expert ultrasonography every three months, showed an SVR in 342 out 360 (95%) patients of which 9 had a new diagnosed HCC (2.63%). Specifically HCC developed in mean after 16,2 months after end of treatment as one or more nodules (2-3 cm in mean) with an increase in alpha-fetoprotein 10 x u.n.v (n.v. <15 UI/mL) in patients with F4 fibrosis staging at the time of treatment enrolment. In conclusion, in view of our findings and literature evidences, regular clinical, laboratory and expert ultrasonography follow-up should carefully performed also on these patients and the current Faster, Higher, Stronger approach to the new antivirals development should strongly be revisited in the light of possible late adverse events like HCC occurrence and the relative economic impact on health care system cost.

The purpose of this study was to determine changes in the mechanical properties of the thigh and lower leg musculature during the early follicular and ovulatory phases. Subjects were 15 female university students with normal menstrual cycles. The early follicular and ovulatory phases were estimated by the basal body temperature method, ovulation kits, and salivary estradiol concentration measurement. The MyotonPRO digital palpation device (Myoton AS, Tallinn, Estonia) was used to measure muscle and tendon stiffness in the early follicular and ovulatory phases. Measurement sites were the rectus femoris (RF), vastus medialis (VM), patellar tendon (PT), medial head of gastrocnemius, soleus, and Achilles tendon. No significant differences in stiffness of all muscle tendons were identified between the early follicular and ovulatory phases. In the ovulatory phase, a significant positive correlation was seen between stiffness of RF and PT, and between stiffness of VM and PT. These results suggest that the stiffness of muscles and tendons of anterior sites of the thigh and posterior sites of the lower leg may not change between the early follicular and ovulatory phases. During the ovulatory phase, tendons may also be stiffer in individuals with stiffer anterior thigh muscles.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Background: The myeloid-epithelial-reproductive tyrosine kinase (MERTK) is involved in hepatic steatosis, inflammation and liver fibrosis. Here we evaluated the association between the MERTK rs4374383 single nucleotide polymorphism (SNP) and liver fibrosis progression in hepatitis C virus (HCV)-infected patients. Methods: We performed a retrospective study (repeated measures design) in 208 patients who had liver stiffness measurement (LSM), which was assessed by transient elastography No patient had cirrhosis at baseline (LSM≥12.5 kPa). Results: At baseline, 53.8% were male, the median age was 47.1 years, 13.5% reported a high intake of alcohol, 10.1% were prior injection drug users, 85.3% were infected by HCV genotype 1, and 22.6% had previously failed antiviral therapy (pegylated-interferon-alpha/ribavirin). During a median follow-up of 46.6 months, 26 patients developed cirrhosis. The rs4374383 G carriers had a higher risk of increasing LSM (adjusted arithmetic mean ratio (aAMR)=1.14; p=0.006) and a higher likelihood of having an increase in LSM greater than 5 kPa (ΔLSM≥5 kPa) [adjusted odds ratio (aOR)=2.37; p=0.029], and greater than 7 kPa (ΔLSM≥7 kPa) [aOR=3.24; p=0.032], after controlling for confounding. The SNP’s association with cirrhosis progression was close to statistical significance (aOR=2.18; p=0.070). Conclusions: MERTK rs4374383 A carriers had a lower risk of liver fibrosis progression than G carriers, supporting the hypothesis that this SNP seems to have a critical role in the pathogenesis of liver disease in HCV-infected patients.

To study the coupling mechanism and dynamic response of the end-face movable gear trans-mission system under complex excitation, a specific configuration of end-meshing movable gear reduction mechanism was used to achieve predetermined rigid thrust transmission and mis-matched gear meshing functions, which solved the inherent defects of traditional harmonic gear mechanism thin-wall flexible wheel easy to be damaged by fatigue. Considering the phenomenon of elastic deformation of live teeth accompanied by significant changes in meshing characteristics in the transmission process of end-meshing harmonic reducer, the influence of dynamic meshing parameters, live tooth deformation, time-varying stiffness of tooth meshing, and time-varying backlash on nonlinear dynamic performance was explored, as well as the mechanism of mul-ti-parameter coupling on transmission performance. The nonlinear dynamics model of the end-meshing harmonic reducer is established to solve the chattering prediction problem. Finally, a comprehensive test bed for the transmission system of harmonic reducer with meshing type with adjustable characteristic end was built to verify the correctness of the theoretical model and provide the theoretical and technical basis for exploring the optimal parameter selection of pas-sive vibration suppression problem.

(1) Background: Globally, neck pain is prevalent, affecting around thirty percent of the population annually. To better understand the influence of pain on the myofascial layers, the present study investigated these on the upper trapezius muscle in unilateral, more severe neck pain. (2) Methods: This study was a cross-sectional study. Forty patients (42.2 ± 14.7) with a confirmed diagnosis of unilateral neck pain were examined using durometry and indentometry. The study evaluated stiffness, elasticity, and pressure pain threshold of both sides of the neck (symptomatic side: SS; healthy side: HS). Furthermore, the range of motion of the cervical spine (lateral flexion, rotation) was quantified using a digital goniometer. (3) Results: A significant lateral discrepancy was observed in stiffness between groups (durometry: SS – 33.76 ± 7.78, HS – 29.75 ± 7.45, p&lt;0.001; indentometry: SS – 59.73 ± 33.93, HS – 4.18 ± 12.69, p=0.024). In contrast, no differences were found between the comparison sides of the upper trapezius for the parameter’s elasticity (SS – 0.101 ± 1.09, HS – -0.006 ± 0.29, p=0.416), cervical spine mobility (lateral flexion: SS – 37.08 ± 8.15, HS – 37.73 ± 7.61, p=0.559; rotation: SS – 73.55 ± 12.37, HS – 72.85 ± 11.10, p=0.660) and algometry (SS – 36.41 ± 17.53, HS – 37.22 ± 17.00, p=0.657). (4) Conclusion: Overall, it can be concluded that more severe neck pain unilaterally shows differences in stiffness on the same side. Future research is needed to investigate the links.

Background: Myocardial infarction is increasing at a young age. New tools are needed to evaluate the risk population of young patients. GDF-15 has been implicated in several key mechanisms of atherogenesis and also is associated with increased mortality and cardiovascular events in patients with coronary artery disease. Arterial stiffness parameters, including pulse wave velocity, can also be measured using peripheral arterial tonometry and can indicate the presence or progression of atherosclerotic changes. The aim of this study is to evaluate the GDF-15 level and arterial stiffness parameters in patients with premature myocardial infarction Method: Thirty patients who recovered from a myocardial infarction were consecutively included. Fifteen age-sex-matched subjects were included as controls. The patients’ serum GDF-15 concentration levels were measured using relevant kits. Measurements of arterial stiffness [pulse-wave velocity (PWV) and augmentation index (AIx)] were performed using a Mobil-O-Graph arteriography system. Results: GDF-15 concentration levels were significantly higher in the patients with premature myocardial infarction when compared to controls. PWV and AIx were similar between the groups. GDF-15 level was negatively correlated with high-density cholesterol (HDL) and positively correlated with uric acid levels in all study populations. Conclusions: GDF-15 levels may be a risk factor for patients with premature myocardial infarction. This pilot study may trigger further studies to elucidate the central role of GDF-15 in the pathophysiology of early atherosclerosis in the young population.

The purpose of this study was to investigate the changes in anterior knee laxity (AKL), stiffness, general joint laxity (GJL), and genu recurvatum (GR) during the menstrual cycle in female non-athletes and female athletes with normal and irregular menstrual cycles. Participants were 19 female non-athletes (eumenorrhea, n=11; oligomenorrhea, n=8) and 15 female athletes (eumenorrhea, n=8; oligomenorrhea, n=7). AKL was measured as the amount of anterior tibial displacement at 67 N - 133 N. Stiffness was calculated as change in (Δ)force/Δ anterior displacement. The Beighton method was used to evaluate the GJL. The GR was measured as the maximum angle of passive knee joint extension. AKL, stiffness, GJL, and GR were measured twice in four phases during the menstrual cycle. Stiffness was significantly higher in oligomenorrhea groups than in eumenorrhea groups, although no significant differences between menstrual cycle phases were evident in female non-athletes. GR was significantly higher in the late follicular, ovulation, and luteal phases than in the early follicular phase, although no significant differences between groups were seen in female athletes. Estradiol may affect the stiffness of the periarticular muscles in the knee, suggesting that GR in female athletes may change during the menstrual cycle.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

As a new type of gear, bevoloid gears have the advantages of compensating axial error, smooth transmission, and eliminating turning error, and they are widely used in applications requiring high transmission accuracy and stability. However, research on calculating the time-varying mesh stiffness of bevoloid gears is still limited, and there is an urgent need to propose a method that can calculate the stiffness of bevoloid gears quickly and accurately. This paper first establishes the bevoloid gear tooth profile expressions, then assumes a pair of bevoloid gears meshing with the same rack and derives the contact line equations of parallel axis bevoloid gear pairs, and analyze the contact process of bevoloid gears. We propose an analytical algorithm that uses the slicing method to calculate the stiffness of helical gears, straight bevoloid gears, and helical bevoloid gears, change the parameters of helical bevoloid gears respectively, and analyze the influence of different parameters on stiffness. Finally, the finite element method is used to verify the analytical method, and the correctness of the analytical calculation results is verified, and the errors are analyzed.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS.Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm³. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume.Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

Background: We aimed to determine the splenic stiffness (SS) values in healthy individuals as measured by 3 Tesla magnetic resonance elastography (3T MRE) and to investigate the possible effects of parameters such as age, sex, spleen volume, diameter, and parenchyma thickness on SS. Methods: A total of 54 healthy volunteers were included in this cross-sectional study. Participants' age and sex information were recorded, in addition to spleen craniocaudal and anteroposterior diameter, cortical thickness, spleen volume, and SS, which were measured using 3T magnetic resonance imaging and MRE. Results: Twenty-nine male and 25 female subjects with a mean age of 54.78±15.40 years were included in the study. Mean cradiocaudal diameter was 10.46±1.16 cm, anteroposterior diameter was 9.88±1.29 cm, parenchyma thickness was 4.08±0.67 cm, SS was 3721.94±709.69 Pascal (Pa), and median spleen volume was 292.54 (239.40-311.00) cm3. A significant positive correlation was observed between age and SS (r=0.779, p<0.001). The SS values were not associated with sex, craniocaudal diameter, anteroposterior diameter, parenchymal thickness, or volume Conclusion:Age should be considered when using SS in the diagnosis and staging of relevant diseases such as portal hypertension and esophageal varices. Our results should be confirmed by future studies using 3T MRE in larger populations.

Rhabdomyosarcoma is a rare cancer arising in skeletal muscle that typically impacts children and young adults. It is a worldwide challenge in child health as treatment outcomes for metastatic and recurrent disease still pose a major concern for both basic and clinical scientists. The treatment strategies for rhabdomyosarcoma include multi-agent chemotherapies after surgical resection with or without ionization radiotherapy. In this comprehensive review, we first provide a detailed clinical understanding of rhabdomyosarcoma including its classification and subtypes, diagnosis, and treatment strategies. Later we focus on chemotherapy strategies for this childhood sarcoma and discuss the impact of three mechanisms that are involved in chemotherapy response including apoptosis, macro-autophagy, and the unfolded protein response. Finally, we discuss in vivo mouse and zebrafish models, and in vitro 3-dimensional bioengineering models of Rhabdomyosarcoma to screen future therapeutic approaches and promote muscle regeneration.

Hydrogels can be considered as mimics of extracellular matrix (ECM).Cytoskeleton through integrins is connected with ECM and cytoskeleton tension depends on ECM stiffness.A number of age-related diseases depend on cellular processes related with cytoskeleton function.Some examples of cancer initiation and progression and heart disease in relationship with ECM stiffness has been analysed.Incorporation of rigid particles in ECM can increase ECM stifness and to promote formation of internal residual stresses. Water migration, changes of water binding energy to biomactomolecules, changes of the state of water from tightly bound water to free and loosely bound water changes stiffness of ECM. Risks related with rigid particles incorporation into ECM have been also iscussed.

In recent times, the soft robotics field is gaining numerous research focus owing to its high level of manipulation capabilities unlike traditional rigid robots, which gives room for an increasing use in other areas. However, compared to traditional rigid gripper robots, being capable of controlling/obtaining overall body stiffness when required is yet to be further explored since soft gripper robots have inherently less rigid properties. unlike previous designs with very complex variable stiffness systems, this paper demonstrates a soft gripper design with minimum system complexity while being capable of varying the stiffness of a continuum soft robotic actuator and proves to have potential applications in gripping objects of various shapes, weights &amp; sizes. The soft gripper actuator comprises two separate mechanisms; the pneumatic mechanism for bending control and the mechanical structure for stiffness variation by pulling tendons using stepper motors which compresses the actuator, thereby changing the overall stiffness. The pneumatic mechanism was first fabricated and then embedded into another silicon layer during which it was as well merged with the mechanical structure for stiffness control. By first pneumatically actuating the actuator which causes bending and then pulling the tendons, we found out that the actuator stiffness value can be increased up to 145 % its initial value, and the gripper can grasp &amp; lift a weight of up to 2.075 kg.

Aiming at the problem that soft robots are challenging to take into account both flexibility and bearing capacity, Using the software Pneu-Net driver as the deformation mode, magnetorheological fluid material phase transformation to achieve variable stiffness, A pneumatic modular soft joint structure with dynamically adjustable deformation and stiffness in all directions is proposed. In this paper, mathematical models of deformation and variable stiffness are established. The correspondence between gas pressure and deformation and applied current and joint stiffness is obtained. The finite element analysis method was used to simulate the deformation characteristics and variable stiffness characteristics of modular joints based on the Yeoh model. Finally, the theoretical and simulation results are verified by deformation and variable stiffness tests. It is proved that the modular joint has good rigid-flexible coupling characteristics.

The modeling of tilting-pad journal and thrust bearings presents a level of complexity beyond that of bearings of fixed-arc geometry, particularly with regard to dynamic influences. With tilting-pad bearings, the theory surrounding the fluid film must be complemented with representative modeling of the pad dynamics. What has been recognized in recent decades has been the significance of the pad support, in particular the flexibility of the pivot region of the pad. The typical model for including the stiffness of the pivot has been based on Hertzian contact theory. Some researchers have been noting that the Hertzian theory does not permit sufficient flexibility in the pivot region. It is suggested that the contact mechanics at the pivot would be better represented as a pairing of rough surfaces. The modeling used here is based on a statistical asperity micro-contact theory for rough-surface line contact that has been extended to include contact stiffness. This model has been applied to the determination of the effective dynamic properties of tilting-pad bearings. The results show that pivot stiffness can be as low as one-third the stiffness determined by Hertzian theory. Comparison to published experimental results confirms the significance of the rough-surface modeling, particularly for the line contacts associated with rocker-back tilting pads.

For orthopaedic applications, additive manufactured (AM) porous scaffolds made of absorbable metals like magnesium, zinc or iron are of particular interest. They do not only offer the potential to design and fabricate bio-mimetic or rather bone equivalent mechanical properties, they also do not need to be removed in further surgery. Located in a physiological environment, scaffolds made of absorbable metals show a decreasing Young’s modulus over time, due to product dissolution. For WE43 scaffolds, during the first days an increase of the smeared Young's modulus can be observed, which is mainly attributed to a forming substrate layer of degradation products on the struts surfaces. In this study the influence of degradation products on the stiffness properties of metallic scaffolds is investigated. For this, analytical calculations and finite element simulations are performed to study the influence of the substrate layer thickness and Young's modulus for single struts and for a new scaffold geometry with adapted polar f2cc,z unit cells. The finite element model is further validated by compression tests on AM scaffolds made from Zn1Mg. The results show, that even low thicknesses and Young's moduli of the substrate layer increases significantly the smeared Young's modulus under axial compression.

Mechanical properties of tumor cytoskeleton are extremely vital for any phases of cancer, especially in tumor invasion and metastasis. However, in current category of anticancer drugs, the cytoskeleton-targeting drugs are limited and its role in tumor progression is unclear. Here, we present the mechanical characteristics of tumor stiffness are tightly regulated by cancer cytoskeleton including actin filaments and microtubule during tumor initiation, growth and metastasis, and review the natural drugs that target cancer cytoskeleton. We define cytoskeleton dynamics as target mechanisms for anticancer drug, and summary the plant, microbial and marine sources of natural products. Furthermore, the material approaches to active cancer mechanics are supplied in this review. We aim to promote the development of anticancer drugs that target tumor mechanics by using those material approaches in future and find its pharmacological application.

Angiogenesis, the sprout and growth of new blood vessels from existing vasculature, is an important process of tumor development for the supply of oxygen and nutrition to cancer cells. Endothelial cell is a critical player in angiogenic process by modulating cell proliferation, cell motility, and cell morphology in the response to pro-angiogenic factors and environments provided by tumor and cancer cells. Recent in vivo and in vitro studies have revealed that gap junction of endothelial cells also participates in the promotion of angiogenesis. Pro-angiogenic factors modulate gap junction function and connexins expression in endothelial cells, whereas endothelial connexins involve in angiogenic tube formation and cell migration of endothelial cells via both gap junction channel function dependent or independent mechanisms. In particular, connexin might have the potential to regulate cell mechanics such as cell morphology, cell migration, and cellular stiffness that are dynamically changed during angiogenic processes. Here, we review the implication for endothelial gap junction and cellular mechanics in vascular angiogenesis.

This study analyzes the modeling and dynamics of a novel passive in Multi-Degree-of-Freedom (MDOF) vibration isolation platform which can achieve significant isolation effect. Symmetrical Scissor-Like structures (SLSs) are utilized in the proposed MDOF isolation platform as the supporting and isolation elastic components. Based on the mathematical modeling and theoretical analysis of the MDOF vibration isolation system with SLSs, the effect of structural parameter and joint friction on stiffness and damping properties is investigated. It is shown that due to geometric relations within the SLSs, the natural frequencies can be reduced via adjusting structural parameters of the SLS for different direction vibration isolation. Theoretical and experimental results show that the SLS isolation platform can achieve much better loading capacity and vibration isolation performance simultaneously by only using linear passive components because of the MDOF adjustable stiffness property. Therefore, with low costing and energy consumption, the proposed novel isolation platform can provide the improvement of vibration suppression in various engineering practices.

Cell mechanics is a biophysical indicator of cell state, such as cancer metastasis, leukocyte activation, and cell cycle progression. Atomic force microscopy (AFM) is a widely used technique to measure cell mechanics, where the Young modulus of a cell is usually derived from the Hertz contact model. However, the Hertz model assumes that the cell is an elastic, isotropic, and homogeneous material and that the indentation is small compared to the cell size. These assumptions neglect the effects of the cytoskeleton, cell size and shape, and cell environment on cell deformation. In this study, we investigated the influence of cell size on the estimated Young’s modulus using liposomes as cell models. Liposomes were prepared with different sizes and filled with phosphate buffered saline (PBS) or hyaluronic acid (HA) to mimic the cytoplasm. AFM was used to obtain the force indentation curves and fit them to the Hertz model. We found that the larger the liposome, the lower the estimated Young’s modulus for both PBS-filled and HA-filled liposomes. This suggests that the Young modulus obtained from the Hertz model is not only a property of the cell material, but also depends on the cell dimensions. Therefore, when comparing or interpreting cell mechanics using the Hertz model, it is essential to account for cell size.

In this paper, a modular wire-actuated robotic arm was designed to improve the safety and adaptability of service robots during human-robot interaction. To raise the stiffness adjustment range of the robotic arm, a symmetric variable-stiffness unit was designed based on flexure, which had compact and simple structure, and lowly nonlinear stiffness-force relationship. In this paper, we focused on the research of the symmetric 1-DOF joint module. Based on the kinematics and stiffness analysis, the pose of the joint module could be adjusted by controlling the length of the wires, and the stiffness of the joint module could be adjusted by controlling the tension of the wires. Because of the actuation redundancy, the pose and stiffness of the joint module could be controlled synchronously. Furthermore, a directly method was proposed for the stiffness-oriented wire tension distribution problem of the 1-DOF joint module. A simulation was carried out to verify the proposed method.

Background: Cardiovascular (CV) morbidity and mortality are many times higher in chronic kidney disease (CKD), as well as IgA nephropathy (IgAN), than in the general population. The occurrence of metabolic syndrome (MetS) and metabolic risk factors are independent risk factors for CV disease and renal progression. The study aimed to determine the prognostic role of metabolic profiles in a homogenous group of CKD patients. Methods: One hundred and forty-five IgA nephropathy patients (92 male, 53 female, age 54.7 ± 13 years) with CKD stage 1-4 were investigated and followed for a median of 190 months. The composite (CV and renal) endpoints included all-cause mortality and any CV event such as stroke, myocardial infarction, revascularization (CV), end-stage renal disease, and renal replacement therapy (renal). Results: Patients with MetS had significantly more endpoint events (16/27 patients vs. 15/98 patients, p = 0.001) compared to the nonMetS group. Of the secondary endpoints (CV or renal separately), the rate of the renal and CV endpoints was significantly higher in the MetS group (p = 0.001 and p = 0.029). The primary endpoint independent predictors of survival were dyslipidemia, eGFR, hemoglobin, urine albuminuria, and diabetes mellitus, as determined by Cox regression analysis. Independent predictors of secondary renal endpoint were dyslipidemia, hemoglobin, urine albumin, and eGFR. Predictors of secondary cardiovascular endpoints were gender, BMI, and diabetes. Kaplan-Meier curves showed significant differences in MetS and non-MetS when examined at the combined endpoints (CV and renal) or at each endpoint separately. The primary endpoint rate increased significantly with the increased number of MetS components (MetS comp. 0 vs. MetS comp. 2+, primary endpoints, p = 0.012). Conclusion: Our results showed that the metabolic profile has a prognostic role not only for renal endpoints but also for CV endpoints in IgAN. BMI, hyperuricemia, hypertension, and diabetes have a predictive value for the prognosis of IgA nephropathy.

Chronic hemodialysis (HD) patients have very high cardiovascular risk. Acute vascular changes during dialysis mediated by factors of the endothelium may have a crucial role in this. Aim: To study acute vascular changes during HD. In 29 consecutive chronic HD patients (age: 65.6±10.4 years) pre-, mid-, and post-HD plasma syndecan-1 (SDC-1) and endothelin-1 (ET-1) levels were measured. Applanation tonometry was performed before HD. SDC-1 levels increased during HD (p=0.004). Males had higher ET-1 levels. Patients were divided into 2 groups based on pulse wave velocity (PWV): PWV≥12 m/s and PWV<12 m/s. Pre-HD and mid-HD SDC-1 levels were higher in the group with PWV≥12 m/s (10.174±2.568 vs. 7.928±1.794 ng/ml, p=0.013, and 10.319±3.482 vs. 8.248±1.793 ng/ml, p=0.044, respectively). Post-HD ET-1 levels were higher in the patient group having PWV≥12 m/s (10.88±3.00 vs. 8.05±3.48 pg/l, p=0.027). Patients having PWV≥12 m/s had higher pre-HD peripheral and aortic systolic blood pressure (p<0.05). Total cholesterol correlated with the SDC-1 decrease during HD (r=0.539; p=0.008). Pre-, mid-, and post-HD SDC-1 correlated with the ultrafiltration (r=0.432, p=0.019; r=0.377, p=0.044; and r=0.401, p=0.012, respectively). SDC-1 and ET-1 contribute to vascular changes observed during HD, and they have correlations with some cardiovascular risk factors.

Background The prognostic value of estimated pulse wave velocity (ePWV) has been infrequently explored in high-risk patient groups. Our study aimed to evaluate the prognostic significance of ePWV among patients undergoing percutaneous coronary intervention (PCI) with drug-eluting stent (DES). Methods A total of 4,119 consecutive subjects who underwent PCI with DES (mean age, 67.1 ± 11.6 years and 33.1% were female) were retrospectively analyzed. ePWV was calculated based on the patient’s age and mean blood pressure. Major adverse cardiovascular event (MACE), including cardiac death, non-fatal myocardial infarction, coronary revascularization, and ischemic stroke, were evaluated. Reults During a median follow-up duration of 3.51 years (interquartile range, 1.35 ~ 6.37 years), there were 746 MACE (18.1%). Multivariable analysis showed that higher ePWV was associated with higher MACE incidence (middle tertile vs. the lowest tertile: hazard ratio [HR], 2.49; 95% confidence interval [CI], 1.81-3.42; P < 0.001; the highest tertile vs. the lowest tertile: HR, 6.18; 95% CI, 4.33-8.80; P < 0.001) The inclusion of ePWV data significantly increased the global chi-square values when added to the clinical information (from 96 to 128; P < 0.001). Conclusion ePWV demonstrated a significant association with MACE in patients who underwent DES implantation. Given its relative simplicity to calculate, ePWV could potentially serve as a valuable instrument for stratifying cardiovascular risk within this high-risk patient population.

In this paper, the feasibility of automated and accurate in vivo measurements of vascular parameters continuously and non-invasively using ultrasound sensor is presented. Vascular parameters such as pulse wave velocity (PWV), blood pressure (BP), arterial compliance (AC) and stiffness index (SI) are affluent indicators of cardiovascular disorders and needs to be monitored non-invasively and continuously during surgeries and follow-up procedures. Cuff based or invasive catheter techniques are considered as gold standard to measure BP and are fed manually to compute AC and SI which employ imaging algorithms. In this context, a Continuous and Non-Invasive Vascular Stiffness and Arterial Compliance Screener (CaNVAS) is developed to measure said parameters continuously and non-invasively using ultrasound sensor. Acoustic waves of 5 MHz (2.2 – 10 MHz) are driven through target arterial walls, reflected echoes captured, pre-processed and frequency shift is used to calculate PWV. It is observed that PWV measured using CaNVAS varies exponentially with BP values obtained from sphygmomanometer (BPMR-120) and this relationship is used to compute instantaneous values of BP. The proposed device is validated by performing measurements on 250 subjects in pre and post exercise conditions and found to have 95% accuracy and an average of 12.5% coefficient of variation.

In this paper we give the improved and new analytical and semi-analytical expression for calcu-lating the magnetic vector potential, magnetic field, magnetic force, mutual inductance, torque, and stiffness between two inclined current-carrying arc segments in air. The expressions are ob-tained either in the analytical form over the incomplete elliptic integrals of the first and the sec-ond time or by the single numerical integration of some elliptical integrals of the first and the second kind. The validity of the presented formulas is proved from the special cases when the inclined circular loops are treated. We mention that all formulas are obtain by the integral ap-proach except the stiffness which is found by the derivative of the magnetic force.

In order to alleviate the problems regarding conventional damping modeling techniques in nonlinear structural simulations, using concentrated plasticity formulation including rotational end springs with no damping plus middle elastic parts with modified assigned damping has recently been proposed. However, a proper selection for springs’ stiffness is a source of contention. In this paper, the effect of choosing different ratios for springs’ rotational stiffness to the elastic part of the elements on the seismic performance of RC moment frames was investigated. Incremental Dynamic Analysis (IDA) was performed and the derived responses were used for seismic performance assessment methodology. The results demonstrate that using flexible springs may lead to a greatly conservative estimation of collapse capacity, annual losses, and repair costs compared to a rigid one. Due to lack of experimental data, it is not possible to certainly assert the most appropriate ratio. However, such variation in the seismic performance of a building model with different stiffness modification necessitates more investigation on this modeling strategy.

By combing continuum topology optimization (TO) method and lattice structure technique, a sandwich aircraft spoiler with a high stiffness-to-weight is designed. TO method is served to produce the shell of the aircraft spoiler and the lattice structure, used as cores, is employed to support the shell. TO problem is established as maximizing the stiffness of the structure with limited material volume. Density-based method is utilized to achieve a 0/1 solution. We then empirically replace the core of the aircraft spoiler by using 3D kagome lattice structure. Two different materials, i.e., aluminum alloy and titanium alloy, are synthetically applied to further reduce the weight and simultaneously improve the strength of the aircraft spoiler. Numerical simulations are conducted to show that the designed aircraft spoiler can meet the service environment with a reduction of its weight by approximately 80% when compared with that of the initial design model. Finally, we have fabricated the designed model with photosensitive resin by using 3D printing technique.

The development of straddle-type monorail tour-transit systems (MTTSs) has received keen attention, raising the need for revisions on related design codes. This work presents a comprehensive assessment of the lateral stiffness limit of steel substructures in MTTSs. Firstly, a wind‒vehicle‒bridge coupling model was established, integrating multibody dynamics and finite element methods. This model was then validated against field test results, considering measured track irregularities as the excitation. Afterwards, a trend analysis and a variance-based sensitivity analysis was performed to investigate the effect of various factors on the dynamic response of MTTS. Referring to existing specifications, an evaluation index for the lateral stiffness of pier columns and track beams was proposed. Results indicate that the pier height significantly impacts the lateral displacement of the pier top, accounting for 87% of the first-order sensitivity index and 75% of the total sensitivity index. In comparison, the lateral stiffness of track beams contributes over 70% to the maximum lateral acceleration and displacement at the mid-span. Finally, the lateral limited values for the displacement at the pier top and the deflection–span ratio of the track beam were determined as 8.04 mm and L/4200, respectively. These findings can serve as valuable references for future research and designs in this field.

The mass of a direct-drive generator is often defined by the requirements for structural stiffness to meet the magnetic stiffness between the rotor and stator surfaces. This paper analyses this magnetic stiffness and estimates the structural stiffness of direct-drive generators for different modes of deflection. The magnetic stiffness modelling is based on an analytical model of the airgap closing forces. The final models are verified using Finite Element analysis and carried out for both permanent magnet and wound rotor generators. It shows that wound rotor machines have higher stiffness requirements than permanent magnet machines. The structural stiffness of the generator rotor and stator are evaluated for different modes by applying spatially-varying forces and finding the associated deflections. Structural stiffnesses for the rotor, stator and bearing are then combined. Finally, the magnetic and structural stiffnesses are combined and a stiffness margin can be found. For the airgap not to close, this combined stiffness must be greater than 0. This method is applied to a relatively stiff and a relatively compliant set of generator structures in a case study in order to find the optimum and more sustainable configuration.

The purpose of this study was to determine the effects of aerobic exercise on carotid to femoral pulse wave velocity (cf-PWV), cell adhesion molecules (intracellular adhesion molecules (ICAM-1), vascular cell adhesion molecules (VCAM-1), and endothelial selectin (E-selectin), and oxidized-LDL in elderly women aged 70–85 years, and to identify the effect of and correlation with vascular stiffness. Forty participants were recruited and divided into three groups; vascular stiffness (VSG, n=14), obesity (OG, n=14), and normal (NG, n=12). All groups were given a 16-week intervention of aerobic exercise, and the data collected before and after exercise were analyzed using SPSS Ver. 23.0. Two-way repeated-measures ANOVA was used to evaluate between-group and time-dependent interaction effects. One-way ANOVA was used to evaluate between-group variations. In addition, the significance was tested using a post-hoc test (Scheffe). The within-group variations by time before and after exercise were examined using a paired t-test, and correlation analysis was performed using Pearson correlation coefficients. Simple regression analysis was performed for variables showing significant differences. The results indicated interaction effects for cf-PWV (p<.001), VCAM-1 (p<.01), E-selectin (p<.05) and oxidized LDL (p<.001). The rate of change of cf-PWV was positively correlated with that of VCAM-1 (r=.352, p<.05) and that of oxidized-LDL (r=.325, p<.05) with statistical significance. To determine the effect of the rate of change of cf-PWV on the rate of change of VCAM-1, the variables were tested, and the coefficient of determination in the regression analysis was .124, indicating that 12.4% of the tested variables fit the standard regression line. The variables for the effect of the rate of change of cf-PWV on the rate of change of oxidized LDL were also tested, and the coefficient of determination in the regression analysis was .106, indicating that 10.6% of the tested variables fit the standard regression line. Thus, the 16-week regular and consistent aerobic exercise program had significant effects on the cf-PWV, ICAM-1, VCAM-1, E-selectin, and oxidized-LDL in elderly Korean women with vascular stiffness, suggesting improvements in vascular stiffness, based on which the intervention is predicted to contribute to the prevention of vascular dysfunction by lowering the risk of cardiovascular disease due to atherosclerosis, as well as having a positive effect in the prevention of impairment of vascular endothelial cells.

Shear deflection effects are traditionally neglected in most structural system identification methods. Unfortunately, this assumption might lead to significant errors in some structures, like deep beams. Although some inverse analysis methods based on the stiffness matrix method including shear deformation effects have been presented in the literature, none of these methods is able to deal with actual rotations in their formulations. Recently, the observability techniques, one of the first methods for the inverse analysis of structures included the shear effects into the system of equations. In this approach, the effects of shear rotation are neglected. When actual rotations on site are used to estimate the mechanical properties in the inverse analysis, it can result in serious errors in the observed properties. This characteristic might be especially problematic in structures such as deep beams where only rotations can be measured. To solve this problem and increase the observability techniques' applicability, this paper proposes a new approach to include shear rotations into the inverse analysis by observability techniques. This modification is based on the introduction of a new iterative process. To illustrate the applicability and potential of the proposed method, the inverse analysis of several examples of growing complexity is presented.

In studies of dynamic stability and power quality, it is necessary to know the mechanical parameters that determine the transient response of a wind turbine. The exact value of these parameters is not as decisive as the power curve can be, but an estimate that is far from reality can distort or even invalidate the simulation results. Despite its importance, this information, especially the inertia, but also the stiffness and damping constant of the drive-train, is hardly available for the turbine model under investigation. In this work, the different bibliographical sources that provide values of blade inertia in kg·m2 will be reviewed, and above all, those that provide a distribution of masses along the span of the blade. With this, different reliable relations will be obtained that allow calculating the inertia of the turbine rotor, based on the mass and length of the blade. When the center of gravity is also available, a very correlated expression is provided to obtain the inertia. The even rarer references to the stiffness and damping constant of the drive-train will also be reviewed.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Initially, renal resistive index (RRI) was investigated to improve diagnosis in kidney diseases, but failed to meet this goal. Recently many papers highlighted the prognostic significance of RRI in chronic kidney disease, in the estimation of revascularization success of renal artery stenoses or the evolution of the graft and recipients in renal transplantation. Moreover, RRI gained importance in prediction of acute kidney injury in critically ill patients. Along with RRI study in renal pathology have been revealed correlations of this index with parameters of systemic circulation. The theoretical and experimental premises of this connection were reconsidered, and studies for analyzing the link between RRI and arterial stiffness, central and peripheral pressure or left ventricular flow were conducted with this purpose. A high amount of data is currently indicating that RRI is influenced more by pulse pressure and vascular compliance than by renal vascular resistance – assuming that RRI reflects the complex interplay between systemic circulation and renal microcirculation and should be considered as a marker of systemic cardiovascular risk beyond its prognostic relevance for kidney disease. In this review we will go through clinical research that revealed the implications of RRI in renal and cardiovascular disease.

Desmoglein 3 (Dsg3) plays a crucial role in cell-cell adhesion and tissue integrity. Increasing evidence suggests that Dsg3 acts as a regulator of cellular mechanotransduction, but little is known about its direct role in mechanical force transmission. The present study investigated the impact of cyclic strain and substrate stiffness on Dsg3 expression and its role in mechanotransduction in keratinocytes. A direct comparison was made with E-cadherin, a well-characterized mechanosensor. Exposure of oral and skin keratinocytes to equiaxial cyclic strain promoted changes in expression and localization of junction assembly proteins. Knockdown of Dsg3 by siRNA blocked strain-induced junctional remodeling of E-cadherin and Myosin IIa. Importantly, the study demonstrated that Dsg3 regulates the expression and localization of YAP, a mechanosensor and an effector of the Hippo pathway. Furthermore, we showed that Dsg3 forms a complex with phospho-YAP and sequestered it to the plasma membrane, while Dsg3 depletion had an impact on both YAP and phospho-YAP in their response to mechanical forces, increasing the sensitivity of keratinocytes to strain- or substrate rigidity-induced nuclear relocation of YAP and phospho-YAP. PKP1 seemed to be crucial in recruiting the complex containing Dsg3/phospho-YAP to the cell surface since its silencing affected both Dsg3 junctional assembly with concomitant loss of phospho-YAP at cell periphery. Finally, we demonstrated that this Dsg3/YAP pathway has an influence on the expression of YAP1 target genes and cell proliferation. Together, these findings provide evidence of a novel role for Dsg3 in keratinocyte mechanotransduction.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

Free vibration calculations of Sandwich plates with curvilinear fiber variable stiffness composite face sheets usually require a significant computing effort to obtain a high computational accu-racy. In order to get the natural frequencies of sandwich plates with high computational accuracy and low computational cost, an improved approach integrating the differential quadrature method (DQM) and first-order shear deformation theory (FSDT) is introduced in this work. The skins of sandwich plates are composed of one or several layers of variable stiffness composite laminates (VSCL) with fiber paths assumed to follow a specific linear pattern. The FSDT and von Kármán strain–displacement relationship were used to derive the governing equations of the sandwich plate, and DQM was applied to discretize such governing equations and solve for the fundamental frequency of the sandwich plate. The computational results were verified and compared with other FSDT–based computational results, and there was good agreement with the suggested model. Also, the variation patterns of the natural frequency under different pa-rameters such as fiber orientation angles, boundary conditions, number of layers, and core/skin thickness were investigated. This study entailed the development of an efficient solution to the problem of the fundamental frequency of VSCL sandwich plates, and the outcomes could pro-vide a basis for future dynamics comparative studies.

Corrugated boards are used for packaging because of their high strength-to-weight ratio, recyclability, and biodegradability. They have an orthotropic sandwich structure with unique characteristics for each direction owing to their flute shape. In this study, the bending behavior was qualitatively analyzed for various variables through an FE-based simulation, and the possibility of an alternative test method for the four-point bending test on a corrugated board was examined through a similarity analysis with the experimental results. The cross-machine direction (CD) bending stiffness through finite element analysis (FEA) simulation was closely related to the thickness of the corrugated board. In AB-flute-double-wall (AB/F-DW), the difference in CD bending stiffness based on the bending direction was approximately 17.2% in the FEA simulation and approximately 10.5% in the experiment. However, the differences in the bending behavior (bending force vs. deflection plot) and bending stiffness based on the phase shift between the two flutes constituting BB-flute-double-wall (BB/F-DW) were insignificant. Overall, the CD bending behavior of the corrugated board was simulated relatively well through FEA simulation. However, it was impossible to simulate the machine-direction (MD) bending behavior through FE-based simulation because of a decrease in convergence and a large error caused by the variability of the contact condition of the modeled test specimen with a non-uniform MD cross-section.

Introduction: Systemic lupus erythematosus (SLE) is an autoimmune disease associated with an increased risk of cardiovascular diseases (CVD), leading to elevated mortality rates among patients. We aimed to evaluate the levels of cardio-ankle vascular index (CAVI), global longitudinal strain (GLS), ventricular-arterial coupling (VAC) and high-sensitivity cardiac troponin (hsTn), in SLE patients and to explore their relationship with clinical parameters. Methods: This cross-sectional study enrolled 82 SLE patients without evident cardiac or kidney impairment and 41 age- and sex matched healthy controls. We comparatively evaluated CAVI, GLS, VAC, and hsTn between SLE patients and controls, and we assessed their association among SLE patients with disease activity based on the SELENA-SLEDAI Activity Index. Multivariate regression analysis was performed to identify independent predictors of CAVI and hsTn within the SLE cohort. Results: In comparison to healthy controls, SLE patients presented with significantly higher CAVI, GLS and hsTn levels, while VAC was significantly reduced (p&lt;0.001). Further, SLE patients with active disease (SELENA-SLEDAI≥4) exhibited higher levels of CAVI and troponin than those with inactive disease (p&lt;0.001). SLEDAI was an independent predictor of CAVI, while VAC and SLEDAI were independent determinants of hsTn in SLE cohort. Conclusion: SLE patients displayed abnormal levels of CAVI, VAC, GLS, and troponin compared to healthy individuals. Our findings implicate the potential of those CV novel CVD risk factors to refine screening and therapeutic strategies for this specific population.

The meticulously engineered powertrain mounting system of hybrid-electric vehicles plays a critical role in minimizing vehicle vibrations and noise, thereby enhancing the longevity of vital powertrain components. However, developing and designing such a system demands substantial time and financial investments due to intricate analysis and modeling requirements. To tackle this challenge, this study integrates data-mining technology into the design and optimization processes of the powertrain mount system. The research focuses on the powertrain mounting system of a transverse four-cylinder hybrid-electric vehicle, employing the CRISP-DM (Cross-Industry Standard Process for Data Mining) methodology to establish a data-mining prediction model for mounting stiffness. This model utilizes three data mining algorithms—Multi-SVR, MRTs, and MLPR—assessing their predictive accuracy concerning mounting system stiffness estimation. A comparative analysis reveals that the MRTs algorithm outperforms others as the most effective prediction model. The proposed predictive model elucidates the quantifiable correlation between vibration isolation performance and installation stiffness, overcoming complexities associated with traditional modeling approaches. Applying this model in powertrain mounting system design showcases the efficacy of the CRISP-DM-based approach, significantly enhancing design efficiency without compromising prediction accuracy.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

Background: Brachial-ankle pulse wave velocity (baPWV) is widely used as a marker of arterial stiffness. It has been suggested as a simple method for detecting arterial loads that can trigger left ventricular hypertrophy in the heart. Increased left ventricular hypertrophy in hypertensive patients is a predictor that will have an impact on increasing morbidity and mortality. Objective: This study aimed to evaluate the correlation between the baPWV and the left ventricular mass index (LVMI) in hypertensive patients. Methods: This cross-sectional study was conducted by collecting secondary data from hypertensive patients at the Heart Outpatient Clinic, with inclusion: aged more than 40 years old, suffering hypertension more than one year, and had baPWV and echocardiography data. Correlation between baPWV and LVMI was evaluated using the Pearson correlation test. Results: A total of 40 hypertensive patients were enrolled in this study. 60% were women. The mean age was 52.92 ± 9.50 years. Mean LVMI was 107.20 + 21.01 gram/m2. LVMI showed a significant association with age and systolic blood pressure (p=0.001 and 0.019, respectively). Mean baPWV was 1832.90 + 336.22 cm/sec. A significant association was found between baPWV and age and systolic blood pressure (p=0.000 and 0.049, respectively). There was a significant positive correlation between baPWV and LVMI (r=0.493, p=0.001); and between baPWV and Relative Wall Thickness (RWT) (r=0.404, p=0.01). Conclusion: This study shows that elevated baPWV is an indicator of increased LVMI in hypertensive patients. Examination of baPWV should be carried out routinely to detect earlier arterial stiffness as a morbidity and mortality prevention strategy in hypertensive patients.

The opened beams always confused the designers due to the guidelines missing. In this research, six hybrid reinforced beams reinforced with mixed steel and basalt fiber reinforced polymer (BFRP) bars had constant cross-sections of 150mm x 300mm and a clear span of 1800mm. Generally, five beams have symmetrical rectangular openings with dimensions of 150mm x 250mm located at a distance of 250mm (equivalent to the beam effective depth) from the beam support in addition to a solid beam that is served as a control reference. The studied parameters included the effect of using internal reinforcement (steel or BFRP bars) provided along the opening or by incorporating an external BFRP sheet around the opening corners. Also, the conduction of double enhancement with internal steel reinforcement bars further external strengthening BFRP sheet was investigated. The relevant results showed that the opened beam without enhancement lost almost 74.66% of the maximum load compared with the solid beam. Placing internal steel or BFRP bars around the openings increased the maximum load by 62.07% and 59.68%, respectively in comparison to the non-enhanced opened beams. Using an external BFRP sheet to strengthen the opening corners of the beam enhanced the maximum load by 76.39% compared with the non-enhanced opened beam. Therefore, if the beam double enhancement with an external BFRP sheet and internal steel reinforcement around the openings, the maximum load increased by 137.40% compared with the non-enhanced opened beam. Ultimately to further analyze the experimental results and confirm their findings, the study was extended to include the numerical analysis using three dimensional finite element modeling and the results correlated very well with the experimental ones.

Finite element (FE) modeling is commonly used as a method to investigate the influence of medical devices, such as implants and screws and their effects on the biomechanical behavior of the spine. Another simulation method is a multi-body simulation (MBS), where the model is composed of several non-deformable bodies. MBS solvers generally require a very short computing time for dynamic tasks compared to an FE analysis. Considering this computational advantage, in this study, we examine whether parameters whose values are not known a priory can be determined with sufficient accuracy using MBS model. Therefore, we propose a Many-at-a-time sensitivity analysis method that allows approximating these a priory unknown parameters without requiring long simulation times. This method enables a high degree of MBS model optimization to be achieved in an iterative process. The sensitivity analysis method is applied to a simplified screw-vertebra model, consisting of an anterior anchor implant screw and vertebral body of C4. An experiment described in the literature is used as a basis for developing and assessing the potential of the method for sensitivity analysis and to validate the models action. The optimal model parameters for the MBS model were determined to be c=823224N/m for stiffness and d=488Ns/m for damping. The presented method of parameter identification can be used in studies including more complex MBS spine models or to set initial parameter values that are not available as initial values for FE models.

The extrusion-based additive manufacturing is a popular fabrication method, which has attracted the attention of various industries due to its simplicity, cheapness, ability to produce complex geometric shapes, and high production speed. One of the effective parameters in this process is the feed of filament that is presented in the production G-code. The feed of filament is calculated according to the layer height, the extrusion width and the length of printing path. All the required motion paths and filling patterns created by commercial software are a set of straight lines or circular arcs that are placed next to each other at a fixed distance. In special curved paths, the distance of adjacent ones is not equal at different points, and due to the weakness of common commercial software, it is not possible to create curved paths for proper printing. Therefore, making a special computer code that can be used to create various functions of curved paths is investigated in this research, and also the feed of filament parameter is studied in detail. Next, by introducing a correction technique, the feed of filament is changed during the curved path to distribute the polymer material uniformly. Finally, composite samples (which have variable stiffness) consisting of curved fibers are produced with the proposed method, and the high quality of printed samples confirm the suggested code and technique.

The aims of the study were to analyze the relationship between the Mediterranean diet (MD) and arterial stiffness and metabolic syndrome (MetS) and its components in individuals aged over 65, overall and by sex. Subjects were people over 65 years of age with a full record of all variables analyzed from the EVA, MARK and EVIDENT studies. Data from 1,280 subjects with a mean age of 69.52±3.58 years (57.5% men) were analyzed. MD was recorded with the validated 14-item MEDAS questionnaire used in the PREDIMED study. MetS was defined following the guidelines of the joint scientific statement from the Programa Nacional de Educación sobre el Colesterol III. Arterial stiffness was assessed with the VaSera VS-1500® device by measuring the cardio-ankle vascular index (CAVI) and the brachial-ankle pulse wave velocity (baPWV). Results: The mean MEDAS score was 6.00 ± 1.90, (5.92 ± 1.92 in men, 6.11 ± 1.88 in women; p = 0.036). The mean CAVI value was 9.30 ± 1.11 (9.49 ± 1.05 men, 9.03 ± 1.13 women; p = &lt;0.001). The mean baPWV value was 15.82 ± 2.56 (15.75 ± 2.46 men, 15.92 ± 2.68 women; p = &lt;0.001). MetS was found in 51% (49% men, 54% women; p = 0.036). Subjects with MetS had lower MD adherence and higher arterial stiffness values than subjects without MetS. Overall, we found a negative association of MD score with the number of MetS components (β = -0.168), with glycemia (β = -0.007), triglycerides (β = -0.003), waist circumference (β = -0.018), CAVI (β = -0.196) and baPWV (β = -0.065), and a positive association with HDL cholesterol (β = 0.013). By sex, associations followed the same direction but without reaching statistical significance with blood glucose and triglycerides in women and with HDL cholesterol and waist circumference in men. Conclusion: Results indicate that greater adherence to the Mediterranean diet decreases arterial stiffness and the percentage of subjects with MetS, although results differed in the association with MetS components by sex.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Background: Takayasu Arteritis (TAK) increases vascular stiffness and arterial resistance. Hypertension and atherosclerosis lead to similar changes. We investigated possible differences in cardiovascular remodeling between these diseases and whether the differences are correlated with immune cell expression. Methods: Patients with active TAK arteritis were compared with age- and sex-matched hypertensive and atherosclerotic patients. In a subpopulation of TAK patients, Treg/Th17 cells were measured before (T0) and after 18 months (T18) of infliximab treatment. Echocardiogram, supraaortic Doppler ultrasound, and lymphocytogram were performed in all patients. Histological and immunohistochemical evaluation of the vessel wall was performed to compare the in vivo results. Results: TAK patients have increased aortic valve dysfunction and diastolic dysfunction. These data have been associated with uric acid levels. A significant increase in aortic stiffness was also noted and associated with peripheral T lymphocyte levels. CD3+CD4+ cell infiltrates were detected in the vessel wall samples of these patients. They had a lower mean percentage of Tregs at T0 than controls, but levels increased significantly at T18. Opposite results were found in Th17 cells. Finally, TAK patients were found to have an increased risk of atherosclerotic cardiovascular disease (ASCVD). Conclusion: Our data suggest that different pathogenic mechanisms of vessel damage, including atherosclerosis, underlie TAK patients compared with control subjects. The increased risk of ASCVD in TAK patients correlates directly with the degree of inflammatory cell infiltration in the vessel wall. Infliximab restores the normal frequency of Tregs/Th17 in TAK patients and allows a possible reduction of steroids and immunosuppressants.

Several noninvasive vascular biomarkers have been suggested for improving the risk stratification for atherothrombotic events. To identify biomarkers suitable for detecting intermediate-risk individuals who might benefit from lipid-lowering treatment (L-LT) in primary prevention, the present study tested the association of plasma LDL-cholesterol with coronary artery calcification (CAC) Agatston score, high carotid and femoral intima-media thickness (IMT), low carotid distensibility and high carotid-femoral pulse-wave velocity in 260 asymptomatic individuals at intermediate cardiovascular risk and free of diabetes and L-LT. High or low vascular biomarkers were considered when their value was above the 95th or below the 5th percentile, respectively, of the distribution in the healthy or in the study population. LDL-cholesterol was independently associated with the CAC score =0 (OR 0.67; 95%CI 0.48-0.92, P=0.01), CAC score >100 (1.59; 1.08-2.39, P=0.01) and with high femoral IMT (1.89; 1.19-3.06, P<0.01), but not with other biomarkers. Our data confirm that in the presence of CAC score =0 in individuals at intermediate risk, L-LT can be avoided, while it should be used in those with CAC score >100. Femoral artery IMT could represent a useful biomarker for decision regarding L-LT, however the reference values according to sex and age should be established in a large healthy population

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

Soft pneumatic actuators/robotics have received significant interest in the medical and health fields, due to their intrinsic elasticity and simple control strategies enabling desired interaction. However, current soft hand pneumatic exoskeletons often exhibit uniform deformation, mismatch the profile of the interacted objects, and seldom quantify the assistive effects during activities of daily life (ADL), such as extension angle and joint stiffness predicted. The lack of quantification poses challenges to the effective and sustainable advancement of rehabilitation technology. This paper introduces the design, modeling, and testing of pneumatic bioinspired Segmented Composite Proprioceptive Bending Actuators (SCPBAs) for hand rehabilitation in ADL tasks. The actuator’s soft-joint/rigid-bone segmented structure, inspired by the human finger anatomy, provides a superior fit compared to traditional continuous structures. A quasi-static model is established to predict the bending angles based on geometrical parameters. The SCPBAs also include a quantitative evaluation of joint stiffness and extension angle utilizing proprioceptive bending information. Additionally, a soft under-actuated hand exoskeleton equipped with SCPBAs demonstrates its potential in ADL rehabilitation scenarios.

To clarify the risk factors for aggravation of esophagogastric varices (EGV) after hepatitis C virus (HCV) eradication with direct-acting antiviral (DAA) therapy, we enrolled 167 consecutive patients with HCV-related compensated cirrhosis who achieved a sustained virological response (SVR) after DAA therapy. During a median of 69 months, EGV was aggravated in 42 (25%) patients despite SVR. The cumulative 1, 3, 5, and 10-year aggravated EGV rates were 7%, 23%, 25%, and 27%, respectively. Multivariate analysis identified platelet count <11.0×10⁴/μL, LSM ≥18.0 kPa, total bile acid ≥33.0 μmol/L, and diameter of left gastric vein (LGV) ≥5.0 mm at HCV eradication as independent risk factors for EGV aggravation post-SVR. In groups that meet all of these risks, the cumulative EGV aggravation rates at 1, 3, and 5 years were 27%, 87%, and 91%, respectively. However, none of the patients who had only one or none of the risk factors experienced EGV aggravation. Platelet count, LSM, total bile acid, and diameter of LGV at HCV eradication were associated with aggravated EGV post-SVR. EGV tends to worsen as two or more of these risk factors increase.

The endoplasmic reticulum (ER) is the major site of membrane biogenesis in most eukaryotic cells. As the entry point to the secretory pathway, it handles more than 10.000 different secretory and membrane proteins. The membrane insertion of proteins, their folding, and ER exit are affected by the lipid composition of the ER membrane and its collective membrane stiffness. The ER is also a hotspot of lipid metabolism for membrane lipids including sterols, glycerophospholipids, ceramides and neural storage lipids. The unfolded protein response (UPR) bears an evolutionary conserved, dual sensitivity to both protein folding-imbalances in the ER lumen and aberrant compositions of the ER membrane, referred to as lipid bilayer stress (LBS). Through transcriptional and non-transcriptional mechanisms, the UPR upregulates the protein folding capacity of the ER and balances the production of proteins and lipids to maintain a functional secretory pathway. In this review, we discuss how UPR transducers sense unfolded proteins and LBS with a particular focus on their role as guardians of the secretory pathway.

This study presents a platform for ex-vivo detection of cancer nodules, addressing automation of medical diagnoses in surgery and associated histological analyses. The proposed approach takes advantage of the property of cancer to alter the mechanical and acoustical properties of tissues, because of changes in stiffness and density. A force sensor and an ultrasound probe were combined to detect such alterations during force-regulated indentations. To explore the specimens, regardless of their orientation and shape, a scanned area of the test sample was defined using shape recognition applying optical background subtraction to the images captured by a camera. The motorized platform was validated using seven phantom tissues, simulating the mechanical and acoustical properties of ex-vivo diseased tissues, including stiffer nodules that can be encountered in pathological conditions during histological analyses. Results demonstrated the platform’s ability to automatically explore and identify the inclusions in the phantom. Overall, the system was able to correctly identify up to 90.3% of the inclusions by means of stiffness in combination with ultrasound measurements, paving pathway towards robotic palpation during intraoperative examinations.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Transition zones are in the places on the track, with a change in the basic composition of the railway body. There are many sections with a sudden change in the stiffness of the structures built. When the trains are running, a longitudinal shock wave is created from the wheels, which hits these building objects with a higher stiffness and deforms the surroundings of these zones. The greatest attention should be paid mainly to the transition points from the fixed track to the classic track with a track bed, including objects of the railway substructure such as bridges, portals of tunnels, etc. As part of the research sections on the main corridor lines, a long-term inspection and monitoring was carried out with a continuous measurement system using the KRAB trolley. Height changes in the deflections of rails are evidence of their behavior. The measurements took place on a fixed track and a track with a ballast. Changes in the height jumps between the fixed railway track and the track with a gravel bed are significant and have been recorded since the tracks were put into operation. These certain height deflections allow designers to develop new, more durable construction designs.

The subject of the research is the investigation of the behavior of railway tracks in locations with a significant change in the stiffness of the track. These locations can be designed from various structural elements and their materials, and this mainly results in a height change of the track level during its operation. These transition zones are monitored and expertly examined in order to detect undesirable deformations of the geometrical position of the track caused by the trains running. The transition zones are at the points where the fixed track transitions to the classic track bed, in our case it is their combination with bridge structures, especially at their supports. In Slovakia, under the conditions of the Railways of the Slovak Republic, the issue is topical within the framework of the modernization of trans-European railway corridors. The results of experimental measurements and their analysis will provide relevant data for subsequent research solutions for their new numerical modeling, which will ensure a smooth passage through these points of change without height fluctuations, vibrations, and shocks from the wheels of train sets.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Characterized in biomedical terms, stretching exercises have been defined as movements applied by external and/or internal forces – to increase muscle and joint flexibility, decrease muscle stiffness, to elevate joint range of motion (ROM), to increase the length of the morpho-functional unit “muscle-tendon”, to improve joint, muscle and tendon movements, contraction and relaxa-tion. The present review examines and summarizes the initial and recent literature data related to the biomechanical, physiological and therapeutic effects of static stretching (SS) on flexibility and other physiological characteristics of the main structural and functional unit “joint-ligaments-tendon-muscle”. The healing and therapeutic effects of SS, soon combined with other rehabilitation techniques (massage, foam rolling – with and without vibrations; hot/cold therapy, etc.) are discussed in relationship to creation of individual (patient-specific) or group programs for treatment and prevention of joint injuries as well as for improving performance in sports. From a theoretical point of view, the role of SS as positively affecting the composition of the connective tissue matrix is pointed out: type I-III collagen synthesis, hyaluronic acid and glucosaminoglycans (GAGs) turnover – under influence of the transforming growth factor beta-1 (TGF-β-1). Different variables as collagen type, biochemistry, elongation and elasticity are used as molecular biomarkers. Recent studies evaluated that the static progressive stretching therapy could prevent/reduce the development of arthrogenic contractures, joint capsule fibrosis, muscle stiffness and need new clinical applications. Combined stretch techniques are proposed and ap-plied in medicine and sports, depending on their long- and short-term effects on variables such as ROM, EMG activity, muscle stiffness, etc. The results obtained are of theoretical and practical interest for development of new experimental, mathematical and computational models and creation of efficient therapeutic programs. The healing SS effects on the main structural and functional unit – “joint-ligament-tendon-muscle” need further investigations, which could clarify and evaluate benefits of SS in prophylaxis and treatment of joint injuries - in healthy and ill in-dividuals, in older adults, as compared to young, active and well-trained persons, as well as to professional athletes.

This paper presents an approach to the Timoshenko beam theory (TBT) using the finite difference method (FDM). The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. The FDM is an approximate method for solving problems described with differential equations. It does not involve solving differential equations; equations are formulated with values at selected points of the structure. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. The model developed in this paper consisted of formulating differential equations with finite differences and introducing additional points at the beam’s ends and at positions of discontinuity (concentrated loads or moments, supports, hinges, springs, brutal change of stiffness, spring-mass system, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends. Moreover, grid points with variable spacing were considered, the grid being uniform within beam segments. First-order, second-order, and vibration analyses of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis, vibration analysis). Finally, a direct time integration method (DTIM) was presented; the FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

This paper analyses the viability of different solutions to passively augment the axial stiffness of a horizontal axis radial levitation passive magnetic bearing (PMB) with topology previously studied. The zero-field cooling (ZFC) of high-temperature superconductor (HTS) bulks promotes higher magnetic impulsion and levitation forces and lower electromagnetic losses than with the field-cooling (FC), but on the other hand, the guiding stability is much lower than with FC. Because of stability reasons, FC was adopted in most superconducting maglev systems. The trend of this research group has been to develop an HTS ZFC horizontal axis radial levitation PMB presenting notable levitation forces with reduced electromagnetic losses, defined by a topology that creates guiding stability. Previous work has shown that even optimizing the bearing geometry to maximize magnetic guidance forces, could not be enough to guarantee the axial stiffness required for many applications. First, the extent to which guidance forces are augmented by increasing the number of HTS bulks in the stator is evaluated. Then, the axial stiffness augmentation by passively adding two limiting permanent magnet (PM) rings is evaluated. Results show that the axial stiffness is highly augmented by adding limiting PM rings with no significant additional investment. This change enables using the studied ZFC superconducting PMB in high-precision axial stability applications, such as precision gyroscopes, horizontal axis propellers and turbines.

This paper revisits the analytical theory of fractional vibrations with the highlights in five aspects. First, we address the cases of structures with frequency dependent mass or damping or stiffness in Sections 2-4. Second, we introduce the theory based on the general second-order vibration motion equation with frequency dependent elements (mass, damping, stiffness) in Sections 5-7. Third, we present the analytical theory of seven specific classes of second-order vibration systems with frequency dependent mass or damping or stiffness in Sections 8 and 9. Fourth, we bring forward the analytical theory of seven classes of fractional vibration systems in Sections 10-12. Finally, as an application, we give the closed form expression of the forced response to multi-fractional Euler-Bernoulli beam in Section 13. The explanation of the nonlinearity of fractional vibrations is given in Section 14.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

This study presents an exact solution to the free vibration analysis of a uniform Timoshenko beam, with a harmonic vibration being assumed. The Timoshenko beam theory covers cases associated with small deflections based on shear deformation and rotary inertia considerations. In this paper, a moment-shear force-circular frequency-curvature relationship was presented. The complete study was based on this relationship and closed-form expressions of efforts and deformations were derived. The free vibration response of single-span systems and spring-mass systems was analyzed; closed-form formulations of matrices expressing the boundary conditions were presented and the natural frequencies were determined by solving the eigenvalue problem. Systems with intermediate mass, spring, or spring-mass system were also analyzed. Furthermore, first-order dynamic stiffness matrices in local coordinates were derived. Finally, a second-order analysis of beams resting on an elastic Winkler foundation was conducted. The results obtained in this paper were in good agreement with those of other studies.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.

We aimed to develop a non-linear regression model that could predict the fat fraction of the liver (USFF), similar to magnetic resonance imaging proton density fat fraction (MRI-PDFF), based on quantitative ultrasound (QUS) parameters. We measured and retrospectively collected the ultrasound attenuation coefficient (AC), backscatter-distribution coefficient (BSC-D), and liver stiffness (LS) using shear wave elastography (SWE) in 90 patients with clinically suspected non-alcoholic fatty liver disease (NAFLD) and 51 patients with clinically suspected metabolic-associated fatty liver disease (MAFLD). The MRI-PDFF was also measured in all patients within a month of the ultrasound scan. In the linear regression analysis, only AC and BSC-D showed a significant association with MRI-PDFF. Therefore, we developed prediction models using non-linear least-squares analysis to estimate MRI-PDFF based on the AC and BSC-D parameters. We fitted the models on the NAFLD dataset and evaluated their performance in 3-fold cross-validation repeated five times. We decided to use the model based on both parameters to estimate the ultrasound fat fraction (USFF). The correlation between USFF and MRI-PDFF was strong in NAFLD and very strong in MAFLD. According to a receiver operating characteristics (ROC) analysis, USFF could differentiate between <5% vs. ≥ 5% and < 10% vs. ≥ 10% MRI-PDFF steatosis with excellent, 0.97 and 0.91 area under the curve (AUC) accuracy in the NAFLD and with AUCs of 0.99 and 0.96 in the MAFLD groups. In conclusion, USFF calculated from QUS parameters is an accurate method to quantify liver fat fraction and to diagnose ≥ 5% and ≥ 10% steatosis in both NAFLD and MAFLD. Therefore, USFF can be an ideal non-invasive screening tool for patients with NAFLD and MAFLD risk factors.