In this paper thermo-mechanical behavior of 4D printed Polylactic Acid (PLA) was investigated, focusing on its response to varying strain rates and temperatures below the glass transition temperature. Dynamic mechanical analysis and uniaxial tensile tests confirmed PLA's dependency on strain rate, showcasing its sensitivity to external stimuli. Stress-strain curves exhibited typical thermoplastic behavior, with yield stresses varying with strain rates, underscoring PLA's responsiveness to different deformation speeds. Clear strain rate dependence was observed, particularly at quasi-static rates, with temperature and strain rate fluctuations significantly influencing PLA's mechanical properties, including yield stress and deformation behavior. Isothermal compression tests demonstrated predictable stress-strain curves with distinct yield points, while adiabatic tests reveal additional complexities such as heat accumulation leading to further softening. Thermal imaging revealed temperature increase during deformation, highlighting the material's thermo-sensitive nature. These findings provide the basis for future research with the focus on advanced modeling techniques and mitigation strategies for self-heating effects, aiming to enhance PLA-based product reliability and performance in applications with deformations at higher strain rates, while also developing models to simulate shape recovery in 4D printed PLA structures at both cold and hot programming temperatures.

Modification of electrode surface with a selective layer gives the possibility to detect target ana-lytes of forensic interest. 3-(4-trifluoromethyl)-phenyl)-thiophene (ThPhCF3) was deposited on a graphite (G) electrode by electrochemical oxidation and characterized as a receptor for the recognition of synthetic stimulants (2-aminoindane, buphedrone, naphyrone). First, the structural characterization of the polymeric layer were obtained from Raman spectroscopy. Second, the electrochemical profiles of selected synthetic stimulants and their affinity to ThPhCF3/G-modified electrodes were studied using square wave voltammetry and electrochemical impedance spec-troscopy. The values of the adsorption constant show the importance of – PhCF3 groups in the interaction with synthetic stimulants, namely recognition by the formation of hydrogen bonds (Kads (buphedrone) < Kads (2-AI)) and interaction with aromatic H atoms (Kads (buphedrone) < Kads (naphyrone)). It was demonstrated that the polymeric layer derived from thiophene with – PhCF3 group is capable to increase the intensity of the electrochemical signal.

The reaction between 5-acetylbarbituric acid and 4-dimethylthiosemicarbazide or 4-hexamethyleneiminyl thiosemicarbazide produces 5-acetylbarbituric-4-dimethylthiosemicarbazone (H2AcbDM) and 5-acetylbarbituric-4N-hexamethyleneiminyl thiosemicarbazone (H2Acbhexim). Eight new complexes with different cooper (II) salts have been prepared and characterized using elemental analysis, molar conductance, UV–vis, ESI-HRMS, FT-IR, magnetic moment, EPR and cyclic voltammetry. In addition, three-dimensional molecular structures of [Cu(HAcbDM)(H2O)2](NO3)·H2O (3a), [Cu(HAcbDM)(H2O)2]ClO4 (4), and [Cu(HAcbHexim)Cl] (6) were determined by single crystal X-ray crystallography, and was carried out an analysis of their supramolecular structure. The H-bonded assemblies were further studied energetically using DFT calculations, MEP surface and QTAIM analyses. In these complexes, the thiosemicarbazone coordinates to the metal ion in an ONS-tridentate manner, in the O-enolate/S-thione form. The electrochemical behavior of the thiosemicarbazones and their copper(II) complexes has been investigated at room temperature using the cyclic voltammetry technique in DMFA. The Cu(II)/Cu(I) redox system was found to be consistent with the quasi-reversible diffusion-controlled process.

The Polyurethane (PU) mixture is a high−performance engineering material with different dynamic properties compared to a hot−mixed asphalt mixture (HMA). This paper analyzed whether the Kramers−Kronig (K−K) relation and thermo−rheological simple properties were applicable to the PU mixture. Based on the result discussion, the PU mixture exhibited thermo−rheological simple properties within the test conditions. The time−temperature superposition principle (TTSP) was applicable for the PU mixture to construct the dynamic modulus master curve using the standard logistic Sigmoidal (SLS) model, the generalized logistic sigmoidal (GLS) model, and the Havriliak−Negami (HN) model. The Hilbert integral transformed SLS and GLS models for the phase angle can accurately fit the measured phase angle data with newly fitted shift factors and predict the phase angle within the viscoelastic range. The Core−Core and black space diagrams both displayed single continuous smooth curves, which can be utilized to characterize the viscoelastic property of the PU mixture. The K−K relation is applicable for the PU mixture to obtain the phase angle master curve model, storage modulus, and loss modulus from the complex modulus test results. The phase angle of the PU mixture cannot be derived from the dynamic modulus data and currently needs to be derived from the laboratory measurement.

Abstract Background: Hypochlorous acid (HA) is a potent disinfectant with broad-spectrum antimicrobial activity against bacteria, fungi, and viruses. Aim: This study aimed to investigate the factors that influence the stability of hypochlorous acid (HOCl) and their impact on its disinfectant properties Methods: This study explored the stability of hypochlorous acid, emphasizing factors that affect its disinfectant efficiency, such as pH level, temperature, and the presence of organic materials. Findings: Our investigation revealed that HOCl is the most stable and effective disinfectant under weakly acidic conditions, where the undissociated form of hypochlorous acid is predominant. Although it is stable under various conditions, its efficacy is compromised by the presence of heavy metals, organic matter, and UV radiation. Conclusions: This comprehensive analysis concludes that, while hypochlorous acid is a highly effective disinfectant, understanding and maintaining the optimal conditions for its stability is crucial for maximizing its disinfection potential. Implications: The findings can be used to formulate new guidelines and regulations to guide the proper formulation, storage, and use of stable HOCL as disinfectants.

Retired Electric vehicles (EVs) batteries are reused in second life energy storage applications. However, the overall performance of repurposed energy storage system (ESS) is limited by the unevenness of individual batteries use in it. Therefore, battery grading is required for optimal performance of ESS. Electrochemical impedance spectroscopy (EIS) based evaluation of battery aging is a promising way to grade lithium-ion batteries. However, it is not practical to measure impedance of mass retired batteries due to high complexity and slowness. In this paper, a broadband multi-sine binary signal (MSBS) perturbation integrated with multichannel EIS system is presented to measure impedance spectra for high-speed aging evaluation of lithium-ion batteries or modules. The measurement speed is multi-times higher than conventional EIS with single-channel configuration. The broadband MSBS is validated with reference sinusoidal sweep perturbation and corresponding root-mean-square error (RMSE) analysis is performed. Moreover, the accuracy of the presented multichannel EIS system is validated by impedance spectra measurement of Samsung INR18650-29E batteries and comparing it with those measured with commercial EIS instrument. A chi-squared error under 0.641% is obtained for all 8-channels. Since the non-linearity of battery has significant impact on quality of impedance spectra. Therefore, Kronig-Kramer (KK) transform validation is also performed.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

In this study, a carbon fiber microelectrode (CF) was applied for the investigation of electrochemical behavior and determination of natural antioxidant, apocynin (APO). Given the limited solubility of APO in water, a mixture of anhydrous acetic acid (AcH) with 20%, v/v acetonitrile (AN) and 0.1 mol L-1 sodium acetate (AcNa) was used. The electrochemical properties of APO were examined through linear sweep voltammetry (LSV), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The anodic oxidation of APO, which is the basis of the method used, proved to be diffusion-controlled and proceeded with a two-electron and one proton exchange. Both radicals and radical cations, arising from the first and second step of electrode reactions, respectively, underwent subsequent chemical transformations to yield more stable final products (EqCiEiCi mechanism). Using optimized DPV conditions, the anodic peak current of APO at potential of 0.925 V vs Ag/AgCl showed a good linear response within the concentration range of 2.7×10-6 – 2.6×10-4 mol L-1. The detection and quantification limits were determined as 8.9×10-7 and 2.7×10-6 mol L-1, respectively. The developed DPV method enabled the successful determination of APO in herbal extracts and in dietary supplements. It should be noted that this is the first method of voltammetric determination of APO.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

A heterograft copolymer with an alginate backbone, hetero-grafted by polymer pendant chains displaying different Lower Critical Solution Temperatures (LCSTs), combined with a pH-responsive Poly(2-vinyl pyridine)-b-poly(ethylene oxide) (P2VP-b-PEO) diblock copolymer forming micellar nanoparticles, was investigated in aqueous media at various pH. Due to its thermoresponsive side chains, the copolymer forms hydrogels with thermo–induced sol–gel transition, above a critical temperature, Tgel (thermo–thickening). However, by lowering pH of the medium in acidic regime, a remarkable increase of the elasticity of the formulation was observed. This effect was more pronounced in low temperatures (below Tgel) suggesting secondary physical crosslinking, which induces significant changes in the hydrogel thermoresponsiveness, transforming the sol–gel transition to soft gel–strong gel. Moreover, the onset of thermothickening shifted to lower temperatures followed by broadening of the transition zone, implying intermolecular interactions between the uncharged alginate backbone with the PNIPAM side chains, likely through H–bonding. The shear–thinning behavior of the soft gel in low temperatures provides injectability, which allows 3D–printing potential applications. Furthermore, the heterograft copolymer/nanoparticles composite hydrogel, encapsulating a model hydrophobic drug in the hydrophobic cores of the nanoparticles, was evaluated as pH-responsive drug delivery system. The presented tunable drug delivery system might be useful for biomedical potential applications.

The process of blood coagulation, wherein circulating blood transforms into a clot in response to internal or external injury, is a critical physiological mechanism. Monitoring this coagulation process is vital to ensure that blood clotting occurs neither too rapidly nor too slowly. Anticoagulants, a category of medications designed to prevent and treat blood clots, require meticulous monitoring to optimise dosage, enhance clinical outcomes, and minimise adverse effects. This review article delves into the various stages of blood coagulation, explores commonly used anticoagulants and their targets within the coagulation enzyme system, and emphasises the electrochemical methods employed in anticoagulant testing. Electrochemical sensors for anticoagulant monitoring are categorised into two types. The first type focuses on assays measuring thrombin activity via electrochemical techniques. The second type involves modified electrode surfaces that either directly measure the redox behaviour of anticoagulants or monitor the response of standard redox probes in the presence of these drugs. The review provides a comprehensive list of different electrode compositions and their detection and quantification limits. Additionally, it discusses the potential of employing a universal calibration plot to replace individual drug-specific calibrations. The insights presented are anticipated to significantly contribute to the sensor community's efforts in this field.

Foodborne illnesses can be infectious and dangerous and most of them are caused by bacteria. Some types of common food-related bacteria exist widely in nature and pose a serious threat to both humans and animals, and can cause poisoning, diseases, disabilities and even death. Rapid, reliable and cost-effective methods for bacteria detection are of paramount importance in food-safety and environmental monitoring. Polymerase chain reaction (PCR), lateral flow immunochromatographic assay (LFIA) and electrochemical method have been widely used in food-safety and environmental monitoring. In this paper, the recent developments (2013-2023) covering PCR, LFIA and electrochemical method for various bacteria detection (Salmonella, Listeria, Campylobacter, Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli)) considering different foods types, analytical performances and the reported limit of detection (LOD) are discussed. It is found that the bacteria type and food sample type contribute significantly to the analytical performance and LOD. Detection by LFIA has higher average LOD (24 CFU/ml) than detection by electrochemical method (12 CFU/ml) and PCR (6 CFU/ml). Salmonella and E. coli in the Pseudomonadota domain usually have low LODs. LODs are usually lower for detection in fish and eggs. LFIA with gold and iron nanoparticles are prominent in the majority of articles of 26 CFU/ml and 12 CFU/ml respectively. Electrochemical method reveals that the average LOD is highest for cyclic voltammetry (CV) of 18 CFU/ml), followed by electrochemical impedance spectroscopy (EIS) of 12 CFU/ml and differential pulse voltammetry (DPV) of 8 CFU/ml. LOD usually decreases when replicate number increases until it remain unchanged. Exponential relations with (R²>0.95) between LOD of Listeria in milk by LFIA and electrochemical method with replicate number have been obtained. Finally, the review discusses the challenges and future perspectives (including the role of nanomaterials/advanced materials) to improve the analytical performance for bacterial detection.

Based on three assumptions of our 4G model of final unification, we have developed simple logics for estimating the unified atomic mass unit, atomic electrochemical equivalents, Faraday constant and Avogadro number. We appeal the science community to review the following points. 1) Unified atomic mass or energy unit can be considered as ‘average rest energy of nucleons minus average binding energy per nucleon of all atomic nuclides plus electron rest energy’. 2) Electrochemical equivalent of any atomic ion is nothing but the ratio of its mass to its charge. 3) Faraday charge is nothing but the ratio of elementary charge to unified atomic mass unit. 4) Faraday mass can be considered as the inverse of Faraday charge. 5) Avogadro number is nothing but the inverse of unified atomic mass unit. 6) Number of atoms per kg can be called as Kg-mole and number of atoms per gram can be called as gram-mole. Following our 4G model, starting form A=5 to 340, for isobars, ‘average binding energy per nucleon’ having maximum binding energy can be estimated with a simple relation of the form, BE/A=A^-1[1-(0.5+0.000935A²)-A^1/3]10.1MeV. It needs a review and fine tuning.

Screen-printed carbon electrode (SPCE) is a useful technique that has been widely used in the practical application of biosensors oriented to point-of-care testing (POCT) due to its characteristics of cost-effectiveness, disposability, miniaturization, wide potential window, and easy of electrode design. Compared with gold or platinum electrodes, surface modification is difficult because the carbon surface is chemically or physically stable. Oxygen plasma can easily produce carboxyl groups on the carbon surface, which act as scaffolds for covalent bonds. However, the effect of O2-plasma treatment on electrode performance remains to be investigated from an electrochemical perspective, and sensor performance can be improved by clarifying the surface conditions of plasma treated biosensors. In this research, we compared antibody modification by plasma treated and physical adsorption, using our original immunosensor based on gold nanoparticles (AuNPs). Consequently, the O2-plasma treatment produced carboxyl groups on the electrode surface, which changed the electrochemical properties owing to electrostatic interactions. It was also found that the surface became hydrophilic, inhibiting non-specific antigen adsorption. The sensitivity was 6.5 times higher than the Limit of Detection (LOD) using physical adsorption.

This study is part of an extended investigation into the quantitative detection of therapeutic molecules with antineoplastic properties, specifically focusing on bleomycin. The objective is to minimize adverse effects while maximizing therapeutic effectiveness. We are presenting the results for bleomycin detection, in terms of cyclic voltammetry and electrochemical impedance spectroscopy. We are continuing an approach we have recently started, of an electrochemical biosensor based on graphene, which is evidenced to be a revolutionary nanomaterial. The vertical graphene biosensor exhibited improved sensitivity, faster response, faster occurrence of the chemical reactions, and higher electrode surface conductivity, than the classical gold IDE sensor. The construction of the electrochemical sensor involved growing vertically aligned graphene nanosheets on the conductive surface of interdigitated electrodes. The results for bleomycin detection emphasized that a simpler surface modification method proved to be more efficient.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

The present study evaluates mold fungal resistance of newly developed loose-fill thermal insulation materials from wheat straw, corn stalk and water reed. Three different processing methods of raw materials was performed by mechanical crushing (Raw, ≤ 20 mm), thermal-mechanical pulping (TMP) using 4% NaOH and steam explosion pulping (SEP). An admixture of boric acid (8%) and tetraborate (7%) was applied to all processed substrates due to their anti-fungal properties. Additionally, the fourth sample group was prepared from SEPs of all raw species without boric acid and tetraborate (SEP*) as control. Samples from all treatments were separately inoculated by 5 different fungal species and incubated in darkness for 28 days at 28 ℃ and RH &gt;90%. The highest resistance to the colonization of mold fungi was achieved by TMP and SEP processing coupled with addition of boric acid and tetraborate, where molds infest only around 35% to 40% of the inoculated sample area. The lowest mold fungi resistance was detected for Raw and SEP* samples, each ~75% that was affected by rich amount of accessible nutrients, suggesting that boric acid and tetraborate additives alone did not prevent mold fungal growth as effective as in combination with TMP and SEP treatments. Together, the achieved fungal colonization scores after combined fungicide and pulping treatments are acceptable for the application of various renewable materials in future thermal insulation product development.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

Technical components should be produced sustainably and are subject to growing demands in terms of durability and reliability. To meet these expectations, the development of thermochemical processes is auspicious. Titanium alloys, which have a comparatively high gas solubility, allow temporary hydrogen (H) loading, often called thermo hydrogen treatment (THT). THT causes lattice deformation and reduces the β transformation temperature. These effects enable an adjustment of the microstructure, which improves the mechanical properties as compared to those produced conventionally. Furthermore, the process is applicable to complex geometries that cannot be surface hardened by mechanical surface treatment techniques. The investigation presented intends to realize a local microstructure gradient in additively via laser-powder bed fusion (L-PBF) manufactured cylindrical Ti–6Al–4V specimens by changing the distribution and morphology of strengthening precipitates as well as the β grain size depending on the distance to the surface, which should improve the material fatigue properties. To evaluate the mechanical properties of such THT-induced microstructure gradients, the resulting change in fatigue life in the LCF and HCF range was determined by stress-controlled cyclic deformation tests. Besides, the resulting microstructure was characterized by means of XRD and TEM. In addition to the additively manufactured and thermo hydrogen treated cylindrical specimens, conventionally produced tube-like specimens were thermo hydrogen treated and examined. For the THT-induced microstructure gradients, numerically simulated H concentration profiles as well as experimentally determined hardness profiles were used for the evaluation of the THT process. The study shows that H-loading at 500°C and H-degassing at 750°C, followed by aging at 550°C, allows the establishment of a microstructure gradient that shows an 8% improvement in fatigue properties compared to a reference condition without THT. The reason for this improvement is an increased volume fraction secondary alpha phase in the near-surface area of the specimens. Moreover, the results show that the process is applicable a tube-like specimen with varying wall thicknesses.

A metal-free electrochemical oxidative difluoroethylation of 2-arylbenzimidazoles was accomplished, which provided an efficient strategy for the synthesis of MeCF2-containing benzo[4,5]imidazo[2,1-a]-isoquinolin-6(5H)-ones. In addition, the method also enabled the efficient construction of various difluoroethylated indolo[2,1-a]isoquinolin-6(5H) ones. Notably, this electrochemical synthesis protocol proceeded well under mild conditions without metal catalysts or exogenous additives/oxidants added.

Purpose: this paper evaluates the effect of thermo-formed aligners with complementary biomechanical attachments (CBA) on periodontal ligaments (PDL) during the expansion process of the maxillary arch using simulations based on the finite element method (FEM). Methods: four types of teeth (canine 3, premolar 4, premolar 5 and molar 6) were modeled using 3D CAD. In addition, aligners, CBAs and PDL were also 3D modeled. With this information, a FEM model was generated, and a clinical rehabilitation scenario was simulated. For the validation of the results, a comparison with medical records was performed. Results: for canine 3, the displacement was 0.134 mm with a maximum stress of 4.822 x10-3MPa in the amelocemental junction. For premolar 4, the displacement was 0.132 mm at a maximum stress of 3.273x10-3MPa in the amelocemental junction. Premolar 5 had a displacement of 0.129 mm and a stress of 1.358 x10-3MPa at 1 mm from the amelocemental junction. Molar 6 had a displacement of 0.124 mm and a maximum stress of 2.440 x10-3MPa. Conclusions: The simulations showed that the use of CBA reduces tooth tipping. The model with Vestibular CBA presented the best results in terms of the dental movement of expansion of the maxillary arch with the use of thermoformed aligners. Significance: Considering the difficulty of performing in vivo tests that evaluate the configuration effectiveness of the different CBA alternatives in thermoformed aligners, FEM techniques were used to reduce time and costs, and get accurate results with minimal errors.

Prostate cancer (PC) is the second most diagnosed cancer among men. It was observed that early diagnosis of disease is highly beneficial for survival of cancer patients. Therefore, extension and increasing quality of life of PC patients can be achieved by broadening the Cancer Screening programs that are aimed at the identification of cancer manifestation in patients at earlier stages before they demonstrate well-understood signs of the disease. Therefore, there is an urgent need in standard, sensitive, robust, and commonly available screening and diagnosis tools for identification of early signs of cancer pathologies. In this respect, “Holy Grail” of cancer researchers and bioengineers for decades have been molecular sensing probes that would allow diagnosis, prognosis, and monitoring of cancer diseases by their interaction with cell-secreted and cellassociated PC biomarkers, e.g. PSA and PSMA correspondinly. At present, most PSA tests are performed at centralized laboratories using high throughput Total PSA immune analyzers which are suitable for dedicated laboratories and are not readily available for the broad health screening. Therefore, the current trend in detection of PC is developments of the portable biosensors for mobile laboratories and individual use. Phage display since its conception by George Smith in 1985 has emerged as a premier tool in molecular biology with widespread applications. This review describes how the paradigm of molecular evolution and phage display revolutionized the methods of early diagnosis and monitoring of PC.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

The detection and analysis of small molecules, typically defined as molecules under 1000 Da, is of growing interest ranging from the development of small molecule drugs and inhibitors to the sensing of toxins and biomarkers. However, due to challenges such as their small size and low mass, many biosensing technologies struggle to have the sensitivity and selectivity for the detection of small molecules. Notably, their small size limits the usage of labeled techniques that can change the properties of small molecule analytes. Furthermore, the capability of real-time detection is highly desired for small molecule biosensors’ application in diagnostics or screening. This review highlights recent advances in label-free real-time biosensing technologies utilizing different types of transducers to meet the growing demand for small molecule detection.

Bipyridine and its related compounds are starting materials or precursors for a variety of valuable substances, such as biologically active molecules, ligands for catalysts, photosensitizers, viologens, and supramolecular architectures. Therefore, it is important to classify the synthesis methods and know their characteristics. Representative examples include the methods using homo- and heterocoupling of pyridine derivatives in the presence of catalyst. Because bipyridine compounds have a high ability to coordinate with metal centers, a decrease in catalytic activity and yield is often observed in the reaction system. To address this issue, the review provides insight into recent advances in bipyridine synthesis using metal complexes under both homogeneous and heterogeneous conditions. Moreover, the review also sheds light on strategies for bipyridine synthesis involving sulfur and phosphorous compounds. These alternative pathways offer promising avenues for overcoming challenges associated with traditional-catalyzed methods, providing a more comprehensive understanding of the synthesis landscape.

In this work, a ZIF-67/MWCNTs/Nafion sensor platform was constructed based on the good adsorption capacity of ZIF-67, the electrical conductivity of multiwalled carbon nanotubes (MWCNTs) and the excellent chemical stability of Nafion for the detection of Cu2+ in water. Meanwhile, the modified materials were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), BET specific surface area test, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and Fourier transform infrared spectrometry (FT-IR). Cyclic voltammetry (CV), electrochemical impedance (EIS), and square wave solvation voltammetry (SWSV) electrochemical methods were used to perform applied test studies on ZIF-67/MWCNTs/Nafion/GCE. The results show that ZIF-67/MWCNTs/Nafion/GCE has high sensitivity (57.5 μA/μM) and a low limit of detection (15.0 nM) for the electrochemical detection of Cu2+ ions in an electrochemical sensing system. It has high adsorption selectivity for Cu2+, and the recovery of Cu2+ in real water reached 98.6%-103%. The modified electrode has good repeatability, reproducibility, anti-interference, and stability, which makes this sensing platform can be practically applied to the detection of domestic water.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

The limits for recording weak signals for electrochemical seismic sensors are determined by their self-noise. At the same time, the noise nature is complex and not fully understood. In this work, for the first time, in addition to the frequency dependences of the noise amplitude, the difference in the phases of the noise currents of the cathodes of an electrochemical sensor has been studied. It has been established that at low frequencies the cathode currents change in an-tiphase. As the frequency increases, the phase difference becomes random. At the same time, the frequency at which the phase difference changes depend on the interelectrode distance; the clos-er the electrodes are located to each other, the greater it is. Physically, this effect is explained by the transition from noise caused by the integral flow of the working fluid to noise associated with vortex flows, the size of which depends on frequency. Thus, a new way of studying noise makes it possible to identify its physical nature and develop new methods of reduction.

In order to search possible residual minor phases in Y-Ba-Cu-O family, powdered mixtures of Y₂O₃ + BaCO₃ + CuO and, independently, superconducting compound YBa₂Cu₃O_7-x have been treated in evacuated cells and elevated temperatures.YBa₂Cu₃O_7-x was reduced to YBa₂Cu₃O₅ by use of the special home designed Taconis-Knudsen vacuum device. A subsequent doping by oxygen converts produced insulator YBa₂Cu₃O₅ to semiconductor or metal YBa₂Cu₃O_5+x (0<x<0.3). In addition to YBa₂Cu₃O₅, 0.05 volume percent of the minor delafossite phase Y₂Cu₂O₄ was being spotted in the powder mixture 1/2 Y₂O₃ + 2BaCO₃+6Cu₂O, heated up to 818 °C in an inert gas atmosphere. An attempt to prepare the insulating bulk delafossite samples was successful, and subsequent doping by oxygen produces novel metallic phases.

The silane (3-Aminopropyl)triethoxysilane (APTES), possesses one terminal amine group and three ethoxy groups extending from each silicon atom, serving as a crucial interface adherent between organic and inorganic materials. In corrosion prevention, APTES is frequently employed as a primer, with subsequent topcoat as an extra protective layer. This topcoat is particularly useful in covering sites where APTES may exhibit poor bonding, such as those involving Cu or Cu-rich alloying elements. In our study, we applied a thin layer of APTES to cleaned AA2024-T3 samples using concentrated vapor deposition, followed by spin-coating with a diluted PS/acetone solution. Through combinatorial experimentation, we investigated the impact of APTES on the corrosion resistance of the coating system on AA2024-T3. Our findings indicate that a higher surface energy of the APTES primer contributes to better corrosion resistance in the overall coating system. This improvement can be attributed to enhanced wettability achieved by the PS/acetone solution on the cured APTES primer, leading to a more uniform coverage of the dried PS topcoat. Additionally, our research revealed that, in the early stages of exposure to the corrosion solution, a thinner APTES primer enhances protection against corrosion. This effect is attributed to hydrolytic stability mechanisms, and the interactions between hydrolyzation/condensation in soaked APTES and the dissolution of naturally formed aluminum oxide pre-existing in the bare samples. Finally, we observed that an APTES primer subjected to additional heat treatment before topcoating exhibits superior performance in corrosion resistance.

Development of load-bearing polymer composite constructions in civil engineering, such as industrial chimneys and gas ducts, requires filling some research gaps. These gaps are related to long-term behavior under mechanical and temperature loads, cyclic ones as well. Such conditions mean that viscoelasticity should be considered. First of all, viscoelastic parameters should be calculated, based on the used inner structure model. Then, due to the high working temperatures, thermal aging should be considered as well. This research is devoted to effects of thermal aging on viscoelastic behavior of polymers. Two sets of experiments were conducted: creep tensile tests and cyclic heating in constrained state. The Kelvin-Voigt viscoelasticity model was used to determine the rheological parameters of binder from experimental creep curves. Thermally-aged binder turned out to lose its viscous properties and became elastic. Cyclic heating was used to compare the behavior of normal and thermally-aged binder and to evaluate the possibility of temperature stress accumulation. Similar to creep tests, cyclic heating showed that aged binder lost viscosity and worked almost perfectly elastic. Non-aged binder was prone to stress accumulation much more. As a result, the rheological behavior of aged and non-aged binder was compared and showed a significant difference. In addition, the influence of temperature stress accumulation on stress—strain state was evaluated and turned out to be significant as well. The obtained results can be further used to predict the mechanical behavior of structures made of polymer composites operating for a long time at elevated temperatures, including those exceeding the glass transition temperature.

The chemical reaction of ion-adsorption type rare earth during in-situ leaching process is accompanied by ion migration and charge movement, making the leaching process electrochemical in nature. The chemical reaction rate plays an important role in the leaching rate of rare earth elements. In this work, electrochemical impedance spectroscopy (EIS) was used to reveal characteristics of electrical resistance alteration and leaching rate of rare earth elements during in-situ leaching. The equivalent circuit model of the leaching process was established, and two critical parameters of solution resistance Rs and charge transfer resistance Rt were analyzed to reflect the electrochemical characteristics. According to the characteristics of electrical resistance alteration, the leaching process was divided into four stages: wetting, reaction, equilibrium, and top water stage. The resistance parameters Rs and Rt decreased first and then increased during the leaching process. The maximum value of Rs was 1330Ω∙cm2 at the end of the top water stage, and the minimum value was 135Ω∙cm2 at the beginning of the equilibrium stage. The maximum value of Rt was 8310Ω∙cm2 at the beginning of the leaching stage, and the minimum value was 21Ω∙cm2 at the end of the reaction stage. Rs and Rt were negatively correlated with the pore size and chemical reaction rate during leaching. With increasing of pore size and reaction rate , the resistance parameter decrease. This study provide a new idea for intelligent monitoring of rare earth ore.

Premature failure and degradation of layers are the main problems for transportation infrastruc-ture. Addressing these issues necessitates implementing structural health monitoring (SHM) for transportation layers. This strategic approach is instrumental in mitigating maintenance expenses, prolonging the operational lifespan, and preventing accidents resulting from abrupt layer col-lapse. To this end, this research investigated the stress/strain and damage detection capabilities of a self-sensing cementitious composite developed for potential utilization in the construction of an intelligent subgrade layer. The prepared self-sensing cementitious composite consisted of 10% cement and hybrid conductive fillers, including multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) in sand. Initial findings reveal that the electrical resistivity of the composite is significantly affected by the concentration of MWCNTs/GNPs, with a minimum concentration of more than 0.5% needed to achieve a responsive cementitious composite. More-over, the piezoresistive analysis indicates that an increase in the concentration of MWCNTs/GNPs and stress levels leads to an improvement in the stress/strain sensing perfor-mance. When the self-sensing cementitious composite is subjected to equivalent stress levels, variations in the FCR exhibit an increasing trend with decreasing resilient modulus, stemming from a decrease in stiffness due to the increased concentration of MWCNTs/GNPs. Additionally, the EIS analysis demonstrates a contraction for the Nyquist curves under compressive ramp loading prior to failure, followed by the expansion of these curves postfailure. Scanning electron microscopy (SEM) images visually showcase the bridging effects of MWCNTs and the filling ef-fects of GNPs within the composite structure.

The research focuses on the electrochemical behavior of TiVN trilayers in a liquid that simulates a physiological environment (blood plasma). TiVN films are obtained through Physical Direct Current Vapor (PVD) Deposition on titanium bases, depositing TiN and VN layers as an intermediate layer during the procedure. Impedance measurements are carried out before and during the wear test to determine the impact on the sample. The results show that the TiVN trilayer enhances corrosion resistance according to the time of exposure to the electrolyte. Initially, the load resistance (Rct) was 10.50 Ohms, but after 16 days, the Rct rose markedly to 13.87 Ohms, signaling an advance in corrosion resistance, a valuable property for wide applications.

Among the electrochemical energy storage (EES) technologies, rechargeable batteries (RBs) and supercapacitors (SCs) are the two most desired candidates for powering a range of electrical and electronic devices. The RB operates on Faradaic processes, whereas the underlying mechanisms of the SC vary as non-Faradaic in the electrical double layer capacitors (EDLCs), Faradaic at the surface of the electrodes in the pseudo capacitors (PCs), and a combination of both non-Faradaic and Faradaic in the hybrid capacitors. The EDLCs offer high power density but low energy density. The hybrid capacitors take advantage of the Faradaic process without compromising their capacitive nature. Unlike batteries, supercapacitors provide high power density and numerous charge-discharge cycles; however, their energy density lags that of batteries. Here, we review recently published critically selected articles on supercapatteries, a generic term that refers to EES devices that can combine the merits of EDLCs and RBs. Also discussed are the properties, design strategies, and future perspectives of supercapatteries.

High-performance properties of interpenetration polymer network (IPN) hydrogels, based on physically crosslinked chitosan (CS) and chemically crosslinked poly(N-isopropylacrylamide) (PNiPAM), have been successfully developed. The IPN of CS/PNiPAM is proposed to overcome the limited mechanical properties of the single CS network. In this study, the viscoelastic behaviors of prepared materials in both solution and gel states have been extensively examined, considering the UV exposure time and crosslinker concentration as key factors. The effect of these factors on gel formation, hydrogel structures, thermal stabilities of networks, and HeLa cell adhesion were studied sequentially. The sol-gel transition was effectively demonstrated through the scaling law, which agrees well with Winter and Chambon's theory. By subjecting the CS hydrogel to the process operation in an ethanol solution, its properties can be significantly enhanced with increased crosslinker concentration, including the shear modulus, crosslinking degree, gel strength, and thermal stability in its swollen state. The IPN samples exhibit a smooth and dense surface with irregular pores, allowing for much water absorption. The HeLa cells were adhered to and killed using the CS surface cationic derivative, then released through hydrolysis by utilizing the hydrophilic/hydrophobic switchable property or thermo-reversible gelation of the PNiPAM network. The results demonstrated that IPN is a highly attractive candidate for anti-fouling materials.

Photocatalytic decomposition of ethylene was performed under UV-Led irradiation at the presence of nanocrystalline TiO2 (anatase, 15 nm) supported on the porous nickel foam. Process was carried out in the high temperature chamber with regulated temperature from ambient to 125°C under flow of reacted gas (ethylene in a synthetic air, 50 ppm) with simultaneous FTIR measurements of sample surface. Ethylene was decomposed with higher efficiency in elevated temperatures with maximum of 28% at 100-125°C. The nickel foam used as support for TiO2 allowed to enhance the ethylene decomposition at the temperature of 50°C. However, at 50°C the stability of ethylene decomposition was not retained within the following reaction run, but it was at 100°C. Performed photocatalytic measurements at the presence of some radicals scavengers indicated that higher efficiency of ethylene decomposition was obtained due to the improved separation of charge carriers and increased formation of superoxide anionic radicals, which were formed at the interface of thermally activated nickel foam and TiO2.

Pt modified BaZr_0.76Y_0.2Ni_0.04O₃ (BZYN) is fabricated and characterized as a stable electrolyte for proton-conducting solid oxide fuel cell (H-SOFC). The utilization of X-ray diffraction method (XRD) and transmission electron microscopy (TEM) enables the identification of the presence of platinum (Pt) in both the crystal lattice sites and the grain interface. This occurrence contributes to a reduction in grain boundary resistance. Consequently, this phenomenon improves the conductivity of the electrolyte. The electrochemical performance of the single cell with Pt modified BZY electrolyte is improved by the reduction of ohmic resistance and enhancement of ion migration. This signifies a noteworthy advancement in the creation of more efficient and durable proton-conducting SOFCs.

Organic electrochemical transistors (OECTs) based on conducting polymers have attracted significant attention in the field of biosensors. PEDOT:PSS and polyaniline (PANI) are representative conducting polymers used for OECTs. While there are many studies on PEDOT:PSS, there are not so many reports on PANI-based OECTs, and a detailed study to compare these two polymers has been desired. In this study, we investigated the fabrication conditions to produce the best performance in the OECTs using the above-mentioned two types of conducting polymers. Two main parameters were film thickness and film surface roughness. For PEDOT:PSS, the optimal conditions for fabricating thin films were a spin-coating rate of 3000 rpm and DI water immersion time of 18 hours. For PANI, the optimal conditions were a spin-coating rate of 3000 rpm and DI water immersion time of 5 seconds, and adding dodecylbenzenesulfonic acid (DBSA) was found to provide better OECT performances. The OECT performances based on PEDOT:PSS were superior to those based on PANI in terms of conductivity and transconductance, but PANI showed excellence in terms of film thickness and surface smoothness, leading to the good reproducibility of OECT performances.

Microbial foodborne pathogens can cause major risks to public health and the food industry. Rapid and accurate detection of these pathogens is crucial to prevent outbreaks and ensure food safety. Traditional single-mode biosensing approaches have their limitations in terms of specificity, sensitivity, and speed. Over the years, there has been an increasing research interest in developing multimodal biosensing strategies that integrate multiple sensing techniques to achieve enhanced accuracy, efficacy, and precision in foodborne pathogen detection. This article review paper explores the current state of multimodal biosensing technologies and their promising applications in the food industry. We discuss various integrated biosensing platforms, including optical, electrochemical, and nanomaterial-based systems, among others. The advantages, challenges, and future prospects of multimodal biosensing for foodborne pathogens are thoroughly examined, highlighting the potential impact of these advanced technologies on food safety and public health.

The effects of organic metabolites produced by a sulfate-reducing prokaryote (SRP) in seawater on the anode corrosion process of magnesium alloy were analyzed by open circuit potential, electrochemical impedance spectroscopy, polarization curve, and other electrochemical methods, combined with scanning electron microscopy and X-ray diffraction. It was found that the product film produced by magnesium alloy anode corrosion was not dense, and the surface of the magnesium anode substrate was exposed during the corrosion process. The corrosion of magnesium anode matrix was accelerated by the simulation of different organic metabolites including mannose, glucuronic acid, and glucose. Thus, the synergistic effect of various metabolites produced by SRP in the corrosion process of magnesium alloy may be considered in future studies.

Electrochemical Impedance Spectroscopy techniques were applied in this work to 9 lead-acid battery prototypes fabricated industrially, divided on three type/technology packages. Frequency dependent impedance changes were interpreted during successive charge/discharge cycles on two distinct stages: 1) immediately after fabrication; and 2) after a controlled aging procedure to 50% Depth of Discharge, following industrial standards. By investigating their State of Health behaviour vs electrical response, three methods were employed, namely the (Q-Q0) total charge analysis, the decay values of Constant Phase Element in the equivalent Randles circuits, and the resonance frequency of the circuit. A direct correlation has been found for prediction of the best performant batteries in each package, thus allowing a qualitative analysis capable to provide the decay of the battery State of Health. We emphasized which parameters are directly connected with their lifetime performance in both stages, and by consequence, which type/technology battery prototype emphasize the best performance. Based on this methodology, the industrial producers can further establish the quality of the novel batteries in terms of performance vs lifespan, allowing them to validate the novel technological innovations implemented in the current prototypes.

This study investigates novel ferrocene-based electrochemical sensors for metal cation detection through the design, synthesis and characterisation of ferrocene derivatives. Specifically, the re-search determines the redox potentials of ferrocene versus decamethylferrocene to provide in-sight into the redox potential variations between them. The investigation also examines how electrochemical oxidation of the ferrocene moiety can modulate host affinity for transition metals cations via effects such as electrostatic interactions and changes to coordination chemistry. Metal ion coordination to receptors containing functional groups like imine and quinoline is explored to elucidate selectivity mechanisms. These findings advance the fundamental understanding of ferrocene electrochemistry and host-guest interactions, supporting the development of improved cation sensors with optimised recognition properties, sensitivity, and selectivity. Overall, the work lays the necessary groundwork for applications in analytical chemistry and sensor technologies through customised ferrocene-derived materials.

An effective approach to fabricate large-scale of conducting polyaniline (PANI) by an in situ anodic electrochemical polymerization on the nickel foam, which coated by a novel aryl diazonium salt (ADS)-functionalized graphene (ADS-G). In present work, ADS-G was used as a high surface area support material for electrochemical polymerization of PANI. Electrochemical performances of the ADS-G/PANI composites exhibited better suitability as supercapacitor electrode materials than that of the PANI. The ADS-G/PANI composites achieved the specific capacitance of 528 F g-1, which was higher than that of PANI (266 F g-1) due to the excellent electrode-electrolyte interaction and synergistic effect of electrical conductivity between ADS-G and PANI in the composites. These findings suggested that the ADS-G/PANI composites were a suitable composite for the potential supercapacitor applications.

In this paper, the sol−gel method was used to synthesize powders of LaMnO3 (LMO), La0.85Ca0.15MnO3 (LCM), and La0.85Sr0.15MnO3 (LSM). We investigated the impact of substituting Ca and Sr at the A−site on the perovskite crystal structure and electrochemical capabilities of LMO. LCM retained its orthogonal structure in comparison to the parent LMO components, whereas LSM transitioned to a rhombic structure. At 0.5 A/g, the specific capacitance of LCM and LSM electrodes is 185.5 F/g and 248 F/g, respectively.The specific capacitance of LCM was more three times than that of the LMO electrode. Among the three samples (LMO, 22.25 m2 g−1; LSM, 31.56 m2 g−1), the LCM sample exhibited the highest specific surface area of 38.79 m2 g−1. The charge transfer resistances of the LMO, LCM, and LSM are 0.48 Ω, 0.36 Ω, and 0.38 Ω, correspondingly. The LCM electrode exhibits the greatest capacitance performance due to its more refined morphology, increased concentration of oxygen vacancy, and more complete utilization of the perovskite bulk structure. The above results demonstrate that Ca or Sr substitution of A−site compounds has great potential for supercapacitor applications.

Wetting of the surface area of an electrode materials as complete as possible is desirable to achieve optimum specific capacity of an electrode material. Keeping this surface area utilized even at high current densities and even when inside of pores is required for high capacitance reten¬tion. The addition of surfactants at very small concentration to aqueous supercapacitor electro¬lyte solutions has been suggested as a way to improved performance in terms of capacitance, ca¬pacitance retention at increased current density and higher stability. Effects are pronounced with car¬bon materials used in electro-chemical double layer capacitors, they are also observed with re¬dox materials. Causes of the observed improvements and mode of operation of the added surfac¬tants seem to need further investigations; they are inconclusive beyond the obvious statement of in¬creased wetting. Reported examples and the current state of understanding are reviewed.

Waste heat recovery stands out as a promising technique to tackle both energy shortages and environmental pollution. Currently, this valuable resource, generated from processes like fuel combustion or chemical reactions, is often dissipated into the environment, despite its potential to significantly contribute to the economy. To harness this untapped potential, a travelling-wave thermo-acoustic generator has been designed and subjected to comprehensive experimental analysis. Fifty-two data corresponding to different working conditions of the system were extracted to build ANN, ANFIS and ANN-PSO models. Evaluation of performance metrics reveals that the ANN-PSO model demonstrates the highest predictive accuracy (R^2=0.9959), particularly in relation to output voltage. This research demonstrates the potential of machine learning techniques for the analysis of thermo-acoustic systems. By doing so, it is possible to get an insight into nonlinearities inherent to thermo-acoustic systems. This advancement empowers researchers to forecast the performance characteristics of alternative configurations with a heightened level of precision.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Wirobond C is a commercial dental casting alloy suitable for the fabrication of crowns, bridges as well as metal-ceramic restorations. This work aims with the study of the effect of ready-to-use Listerine® and Meridol® mouthwashes and sodium fluoride on corrosion resistance of the CoCrMo dental alloy to electrochemical corrosion in artificial saliva at 37 °C. SEM, EDS, SKP, and microhardness investigations were carried out to characterize the material under study. In vitro corrosion resistance of the CoCrMo alloy was conducted by the open circuit potential method, electrochemical impedance spectroscopy, and anodic polarization curves. The presence of Co 59.8(8) wt.%, Cr 31.5(4) wt.%, and Mo 8.8(6) wt.% was confirmed. The CoCrMo alloy was characterized by Vickers microhardness of 445(31) µHV0.3. Based on EIS data, the capacitive behavior and high corrosion resistance of CoCrMo alloy was revealed. The kinetics of pitting corrosion in the artificial saliva was lower after the modification with NaF and Listerine and Meridol mouthwashes. The potentiodynamic characteristics revealed the passive behavior of CoCrMo alloy in all solutions. Based on the SKP measurements of the CoCrMo alloy after corrosion tests, the effect of artificial saliva modification on electronic properties of Bego Wirobond C dental alloy was found.

Microbial cell factories offer an eco-friendly alternative for transforming raw materials into commercially valuable products, primarily because of their reduced carbon impact compared to conventional industrial procedures. These systems often depend on lignocellulosic materials, mainly pentose and hexose sugars, richly available carbon reservoirs. Nevertheless, these resources might not always be efficient due to the limited supply, significant cost, and other considerable obstacles. One major hurdle when working with sugars derived from lignocellulosic biomass, especially glucose, is balancing carbon allocation to satisfy energy, cofactor, and other essential component needs for cellular proliferation while maintaining a robust yield. Furthermore, nearly half or more of this carbon is inevitably lost as CO2 during the biosynthesis processes, which serves to generate the energy necessary for maintaining cell growth and other regular metabolic activities. This carbon loss lowers the theoretical production yield and compromises the benefit of reducing greenhouse gas emissions – a fundamental advantage of biomanufacturing. This review paper posits the perspectives of using CO2 from atmosphere, industrial wastes, or the exhausted gases generated in microbial fermentation as a feedstock for biomanufacturing. Both one-step direct CO2 fixation or two-step indirect CO2 fixation and conversion strategies are discussed, which can minimize the carbon loss, significantly increase the carbon yield, and eventually achieve the carbon-neutral or -negative goals. The one-step strategy uses novel metabolic pathway design and engineering approaches to directly fix the CO2 via the pathway toward the synthesis of the desired fermentation products. Due to the limitation of the yield and efficiency in one-step CO2 fixation, the two-step strategy aims to completely avoid carbon loss in biomanufacturing by integrating a first electrochemical fixation of the exhausted CO2 into C1/C2 products such as formate, methanol, acetate, and ethanol and a second fermentation unit to utilize the CO2-derived C1/C2 chemicals or co-utilize both C5/C6 sugars and C1/C2 chemicals for product formation. The great potentials and challenges of using CO2 as a feedstock for further biomanufacturing are also discussed.

The utilization and engineering of thermo-optic effects have found broad applications in integrated photonic devices, facilitating efficient light manipulation to achieve various functionalities. Here, we perform both an experimental characterization and theoretical analysis of these effects in integrated micro-ring resonators in high index doped silica (HIDS), which has had many applications in integrated photonics and nonlinear optics. By fitting the experimental results with theory, we obtain fundamental parameters that characterize their thermo-optic performance, including the thermo-optic coefficient, the efficiency for the optically induced thermo-optic process, and the thermal conductivity. The characteristics of these parameters are compared to those of other materials commonly used for integrated photonic platforms, such as silicon, silicon nitride, and silica. These results offer a comprehensive insight into the thermo-optic properties of HIDS based devices. Understanding these properties is essential for efficiently controlling and engineering them in many practical applications.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

Hydrogen peroxide (H2O2) is an essential analyte for detecting neurodegenerative diseases and in-flammatory processes and plays a crucial role in pharmaceutical, food industry, and environmental monitoring. However, conventional H2O2 detection methods have drawbacks such as lengthy analysis time, high costs, and bulky equipment. Non-enzymatic sensors have emerged as promising alternatives to overcome these limitations. In this study, we introduce a simple, portable, and cost-effective non-enzymatic electrochemical sensor based on carbon black (CB) and silver nano-particle-modified δ-FeOOH (Ag/δ-FeOOH), integrated into a disposable electrochemical cell (DCell). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrochemical impedance spectroscopy (EIS), confirmed successful CB and Ag/δ-FeOOH immo-bilization on the DCell working electrode. Electrochemical investigations revealed that the DCell-CB//Ag/δ-FeOOH sensor exhibited an approximately twofold higher apparent heterogene-ous electron transfer rate constant than the DCell–Ag/δ-FeOOH sensor, capitalizing on CB ad-vantages. Moreover, the sensor displayed excellent electrochemical response for H2O2 reduction, boasting a low detection limit of 22 µM and a high analytical sensitivity of 214 μA mM-1 cm-2. Notably, the DCell-CB//Ag/δ-FeOOH sensor exhibited outstanding selectivity for H2O2 detection, even in potential interferents such as dopamine, uric acid, and ascorbic acid. Furthermore, the sensor demonstrated its suitability for monitoring H2O2 in complex biological samples, as evidenced by H2O2 recoveries ranging from 92% to 103% in 10% fetal bovine serum. These findings underscore the considerable potential of the DCell-CB//Ag/δ-FeOOH sensor for precise and reliable H2O2 monitoring in diverse biomedical and environmental applications.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

In this study, we investigated the effects of three surface treatment techniques on 316L stainless steel, low-temperature immersion corrosion, shot peening followed by immersion corrosion, and electrochemical corrosion. Surface alterations were analyzed using scanning electron microscopy, Raman spectroscopy, and α-step thin-film thickness profiling. Human osteoblast adhesion was evaluated using Liu’s stain and metallographic optical microscopy. The results revealed weak cell adhesion after low-temperature immersion and shot peening followed by immersion corrosion. By contrast, electrochemical corrosion, particularly with a high current density and low corrosive solution concentration, resulted in a uniformly corroded surface, thus promoting dense cell adhesion. All three techniques resulted in porous oxide layers. Overall, our experimental findings highlighted shot peening (1 kg/cm2 for 20 s) and electrochemical corrosion (0.5 M HCl) as effective processes. Electrochemical corrosion produced uniformly dense corrosion pits, whereas shot peening produced semicircular grooves with small corrosion pits, both favorable for cell adhesion. Electrochemical corrosion also yielded excellent cell adhesion, emphasizing its suitability for biomedical activity. We developed a process for creating a porous surface layer and thereby enhancing the cell adhesion to 316L stainless steel for potential biomedical implant applications.

THz radiation has assumed a great importance thanks to the efforts in the development of technological tools used in this versatile band of the electromagnetic spectrum. Here we propose a reflecting bi-mirror axicon-like device with wavelength-independent long focusing performances in the THz band, by exploiting the high thermo-mechanical deformation of the elastomer polydimethylsiloxane (PDMS). This deformation permits to achieve significant optical path modulations in the THz band and effective focusing. The surface of a PDMS layer is covered with a gold thin film, acting as heater thanks to its absorption for wavelengths below ~500 nm . An invariance property of the Fresnel integral has been exploited to verify experimentally the THz performances of the device with an ordinary visible laser source, finding excellent agreement with the theoretical predictions at 1 and 3 THz. The same property allowed also to verify experimentally that the axicon focus has a longitudinal extension much greater than that one exhibited by a benchmark cylindrical mirror with the same optical power. The axicon is thermo-mechanically stable up to a heating power of 270 mW, although it might be potentially exploited at higher powers with a minor degradation of the optical performances.

LiFePO4 (LFP) has undergone extensive research and is a promising cathode material for Li-ion batteries. The high interest is due to its low raw material cost, good electrochemical stability, and high-capacity retention. However, poor electronic conductivity and a low Li+ diffusion rate decrease its electrochemical reactivity, especially at fast charge/discharge rates. In this work, the volumetric energy density of lithium-ion batteries is successfully increased by using different amounts of conductive carbon (Super P) in the active material content. The particle size and morphology of the electrode material samples are studied using field emission scanning electron microscopy and dynamic light scattering. Two-point-probe DC measurements and adhesive force tests are used to determine the conductivity and evaluate adhesion for the positive electrode. Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and charge/discharge tests are used to analyze the electrochemical properties of the battery. The samples containing 88% LFP, 5.5% Super P and 6.5% PVDF perform best, with discharge capacities reaching 169.8 mAhg-1 at 0.1C, and they can also manage charging/discharging of 5C. EIS indicates that this combination produces the lowest charge-transfer impedance (67 Ω) and the highest Li+ ion diffusion coefficient (5.76 x 10-14 cm2s-1).

This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

Curcumin, a nontoxic and cheap natural medicine, has high therapeutic efficacy for many diseases including diabetes and cancers. Unfortunately, its exceedingly low water-solubility and rapid degradation in the body severely limit its bioavailability. In this work, we prepare a series of biocompatible poly(vinyl anisole)@nonlinear poly(ethylene glycol) (PVAS@PEG) core-shell nanogels with different PEG gel shell thickness to provide high water solubility, good stability, and controllable sustained release of curcumin. The PVAS nanogel core is designed to attract and store curcumin molecules for high drug loading capacity and the hydrophilic nonlinear PEG gel shell is designed to offer water dispersibility and thermo-responsive drug release. The obtained nanogels are monodispersed in spherical shape with clear core-shell morphology. The size and shell thickness of the nanogels can be easily controlled by changing the core-shell precursor feeding ratios. The optimized PVAS@PEG nanogels display a high curcumin loading capacity of 38.0 wt%. The nanogels can stabilize the curcumin from degradation at pH =7.4 and release the curcumin in response to heat in the physiologically important temperature range. The nanogels can enter cells effectively and exhibit negligible cytotoxicity to both the B16F10 and HL-7702 cells at a concentration up to 2.3 mg/mL. Such designed PVAS@PEG nanogels have a great potential to be used for delicate drug delivery.

Currently, efficient utilization of low-grade thermal energy is a great challenge. Thermoelectricity is an extremely promising method of generating electrical energy from temperature differences. As a promising energy conversion technology, thermo-electrochemical cells (TECs) have attracted much attention in recent years for their ability to convert thermal energy directly into electricity with high thermal power. Within TECs, anions and cations gain and lose electrons, respectively at the electrodes using the potential difference between the hot and cold terminals of the electrodes by redox couples. Additionally, the anions and cations therein are constantly circulating and mobile via concentration diffusion and thermal diffusion, providing an uninterrupted supply of power to the exterior. This review article focuses mainly on the operation of TECs, recent ad-vances in redox couples, electrolytes, and electrodes. The outlook for optimization strategies re-garding TECs is also presented in this paper.

The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

Millions of people worldwide are affected by diabetes, a chronic disease that continuously grows due to abnormal glucose concentration levels present in the blood. Monitoring blood glucose concentrations is therefore an essential diabetes indicator to aid in the management of the disease. Enzymatic electrochemical glucose sensors presently account for the bulk of glucose sensors in the market. However, their disadvantages are that they are expensive and are dependent on environmental conditions, hence affecting their performance and sensitivity. To meet the increasing demand, non-enzymatic glucose sensors based on chemically modified electrodes for the direct electrocatalytic oxidation of glucose are a good alternative to the costly enzymatic-based sensors currently on the market, and the research thereof continues to grow. Nanotechnology-based biosensors have been explored for their electronic and mechanical properties, resulting in enhanced biological signalling through the direct oxidation of glucose. Copper oxide and copper sulfide exhibit attractive attributes for sensor application, due to their non-toxic nature, abundance, and their unique properties. Thus, in this review, copper oxide and copper sulfide-based materials, are evaluated based on their chemical structure, morphology, and fast electron mobility as suitable electrode materials for non-enzymatic glucose sensors. The review highlights the present challenges of non-enzymatic glucose sensors that have limited their deployment into the market.

Electrochemical biosensors based on immobilized enzymes are among the most popular and commercially successful biosensors. Literature in this field suggests that modification of electrodes with nanomaterials is an excellent method for enzyme immobilization, which can greatly improve the stability and sensitivity of the sensor. However, the poor stability, weak reproducibility, and limited lifetime of the enzyme itself still limit the requirements for the development of enzyme electrochemical biosensors for food production process monitoring. Therefore, constructing sensing technologies based on enzyme electrochemical biosensors remains a great challenge. This article outlines the construction principles of four generations of enzyme electrochemical biosensors and discusses the applications of single-enzyme systems, multi-enzyme systems and nano-enzyme systems developed based on these principles. The article further describes methods to improve enzyme immobilisation by combining different types of nanomaterials such as metals and their oxides, graphene-related materials, metal-organic frameworks, carbon nanotubes and conducting polymers. In addition, the article highlights the challenges and future trends of enzyme electrochemical biosensors, providing theoretical support and future perspectives for further research and development of high-performance enzyme chemical biosensors.

The present study aimed to evaluate the effect of the citric acid on the properties of solid pine wood, which were submitted to thermomechanical treatment. A preliminary test was performed in a previous study to evaluate the influence of different temperatures of pressing and concentrations of citric acid over the physical properties of wood. After choosing the best treatments (170°C and 5% and 10% of citric acid) it was evaluated the effect of these on the chemical properties (SEM, FTIR and pH), on the density profile using an X-ray microtomography, and on the resistance to ageing through abrasion test. The result of the chemical analysis allowed to observe an increase of the presence of ester functional groups, as well as a better coverage and higher acidity of the surface. The density profile technique allowed to observe the formation of peaks of density on the surface where the acid was applied. Lastly, it was also possible to verify an increase in the resistance to abrasion because of the application of the citric acid.

Animal viruses are a significant threat to animal health and are easily spread across the globe with the rise of globalization. The limitations in diagnosing and treating animal virus infections have made the transmission of diseases and animal deaths unpredictable. Therefore, early diagnosis of animal virus infections is crucial to prevent the spread of diseases and reduce economic losses. To address the need for rapid diagnosis, electrochemical sensors have emerged as a promising tool. Electrochemical methods present numerous benefits, including heightened sensitivity and selectivity, affordability, ease of use, portability, and rapid analysis, making them suitable for real-time virus detection. This paper focuses on the construction of electrochemical biosensor, as well as promising biosensor models, and expounds its advantages in virus detection, which is a promising research direction.

The rapid, sensitive, and selective detection of pathogenic bacteria is of utmost importance in ensuring food safety and preventing the spread of infectious diseases. Here, we present a novel, reusable, and cost-effective impedimetric sensor based on a dual bacteria-imprinted polymer (DBIP) for the specific detection of Escherichia coli O157:H7 and Staphylococcus aureus. The DBIP sensor stands out with its remarkably short fabrication time of just 20 minutes, achieved through the efficient electro-polymerization of o-phenylenediamine monomer in the presence of dual bacterial templates, followed by in-situ template removal. The key structural feature of the DBIP sensor lies in the cavity-free imprinting sites, indicative of a thin layer of bacterial surface imprinting. This facilitates rapid rebinding of the target bacteria within a mere 15 minutes, while the sensing interface regenerates in just 10 minutes, enhancing the sensor's overall efficiency. A notable advantage of the DBIP sensor is its exceptional selectivity, capable of distinguishing the target bacteria from closely related bacterial strains, including different serotypes. Moreover, the sensor exhibits high sensitivity, showcasing a low detection limit of approximately 9 CFU mL-1. The sensor's reusability further enhances its cost-effectiveness, reducing the need for frequent sensor replacements. The practicality of the DBIP sensor was demonstrated in the analysis of real apple juice samples, yielding good recoveries. The integration of quick fabrication, high selectivity, rapid response, sensitivity, and reusability makes the DBIP sensor a promising solution for monitoring pathogenic bacteria, playing a crucial role in ensuring food safety and safeguarding public health.

This study examines the behavior of stearic acid (SA) and 12-hydroxystearic acid (12-HSA) aqueous mixtures as a function of temperature and 12-HSA/SA molar ratio (R). Whatever R, the system exhibits a morphological transition at a given threshold temperature, from multilamellar self-assemblies at low temperature towards small micelles at high temperature, as shown by a combination of transmittance measurements, Wide Angle X-ray diffraction (WAXS), small angle neutron scattering (SANS) and differential scanning calorimetry (DSC) experiments. Such transition originates from the melting of the crystallized fatty acids within the lamellar phase. The precise determination of the threshold temperature, which ranges between 20°C and 50°C depending on R, allows for the construction of the whole phase diagram of the system as a function of R. At high temperature the micelles that are formed are oblate for pure SA solutions (R = 0) and prolate for pure 12-HSA solution (R = 1). In the case of mixtures, there is a progressive continuous transition from oblate to prolate shape when increasing R, with micelles that are almost purely spherical for R = 0.33.

Cancer is a common illness with a high mortality. Compared to traditional technologies, biomarkers detection, with low cost and simple operation, has higher sensitivity and faster speed in early screening and prognosis of cancer. Therefore, extensive research has been focused on the development of biosensors and the construction of sensing interfaces. Molybdenum disulfide (MoS2) is a promising two-dimensional (2D) nanomaterial, whose unique adjustable bandgap shows excellent electronic and optical properties in the construction of biosensor interfaces. It not only has the advantages of high catalytic activity and low manufacturing costs, but also can further expand the application of hybrid structures by different functionalization, and is widely used in various biosensors fields. Herein, the application of electrochemical and optical sensing platforms based on MoS2 in the detection of cancer biomarkers was comprehensively reviewed. Firstly, the structure and preparation method of MoS2 were introduced, and its applicable characteristics in the field of biosensors were explored. Secondly, we comprehensively reviewed the recent construction and application of sensing platform based on MoS2 in the field of cancer biomarkers detection in both electrochemical and optical aspects. The prime characteristics and application performances of MoS2 and its composites were emphasized. Additionally, we also involved some other types of biosensors based on MoS2. Finally, we summarized the challenges and development prospects of MoS2 in the application of cancer biomarkers detection, and provided some insights for the application potential of this kind of emerging nano-materials in a broader field.

Antioxidants are very beneficial for health because they protect the body from the effects of free radicals on various degenerative diseases caused by food contamination, air pollution, sunlight, etc. In general, methods for measuring the capacity of antioxidants generally use accurate meth-ods such as spectrophotometry and chromatography. Still, it takes time, sample preparation and must be done in a laboratory with particular expertise. Therefore, a new, more practical method needs to be developed for determining antioxidants, namely the electrochemical method. The electrochemical method is promising to develop because it has several advantages, including high sensitivity and fast response. The electrochemical method discussed in this article reviews sensors, biosensors, and nanosensors. This paper comprehensively analyzes contemporary developments in electrochemical biosensor techniques and antioxidant evaluation methodologies. The discussion centers on utilizing multiple biosensors. Electrochemical biosensors have been determined to be prevalent in analyzing food quality, assessing active factor functionality, and screening practical components. The present study outlines the difficulties linked with electrochemical bio-sensor technology and provides insights into the potential avenues for future research in this domain.

Analytical chemistry applied to medical and diagnostic analysis, recently focused on the development of cost-effective biosensors able to monitor the health status or to assess the level of specific biomarkers that can be indicative for several diseases. The improvement of technologies relating to the possibility of non-invasive sampling of biological fluids, as well as sensors for the detection of analytical signals and the computational capabilities of the systems routinely employed in everyday life (e.g. smartphones, computers, etc.), make the complete integration of self-standing analytical devices more accessible. This review aims to discuss the biosensors that have been proposed in the last 5 years focusing on two principal detecting approaches, optical and electrochemical, which have been employed for quantifying different kind of target analytes reaching detection limits below the clinical sample levels required. These detection principles applied to Point-of-care (POC) devices, have been extensively reported in literature and even the limited examples found on the market are based on these strategies. This work will show the latest innovations considering the integration of optical and electrochemical detection with the most commonly reported analytical platforms for POC applications such as paper-based or wearable and implantable devices.

This paper discusses the mathematical modelling of exothermic explosions in a slab. This model is based on a nonlinear equation containing a nonlinear term related to Arrhenius, bimolecular, and sensitised laws of reaction kinetics. The absolute temperature can be obtained by solving the nonlinear equation using Akbari-Ganji’s method. The influence of the parameters Frank-Kamenetskii, activation energy and numerical exponent on temperature is discussed. The analytical results are compared with previous available analytical and numerical results ( Matlab). A satisfactory agreement is noted.

Biosensors are analytical devices that utilize biological interactions to detect and quantify clinical biomarkers, contaminants, allergens, and microorganisms. They combine different disciplines including analytical chemistry, molecular biology, and electrical engineering. Biosensors operate by coupling a bioreceptor, such as nucleic acid or proteins, with a transducer that converts the biological interaction into an electrical signal. Electrochemical and optical transduction are commonly used approaches due to their high detection capability and compatibility with miniaturization. Biosensors provide both high specificity and sensitivity and can be integrated into low-cost microfluidic platforms for rapid and point-of-care applications. These attributes make these devices valuable tools in analytical chemistry, particularly for early diagnostic applications. However, conventional biosensors face challenges related to the immobilization of biorecognition elements on the transducer surface, leading to issues like lost of sensitivity and selectivity. To address these problems, the introduction of nanomaterials, particularly magnetic nanoparticles (MNPs) and magnetic beads (MBs), has been implemented. MNPs combine their magnetic properties with other interesting characteristics such as small size, high surface-to-volume ratio, and excellent biocompatibility. They can be tailored for specific applications and have been extensively used in various fields, including biosensing and clinical diagnosis. Furthermore, MNPs simplify sample preparation by isolating target analytes through magnetic separation, thus improving sensitivity, and reducing analysis time and interference phenomena. The synthesis and modification of MNPs play a crucial role in adjusting their properties for different applications. This review presents an overview of the synthesis and surface modifications of magnetic nanoparticles, their role in the development of biosensors and bioassays, and their applications across various scientific areas.

The plastic deformation behavior of 3Y-TZP with weak electric current in oxygen-lean atmosphere was investigated. An electrochemical reduction reaction, induced by the electric current, can significantly promote the plastic deformation of 3Y-TZP at furnace temperature of 1200 °C and a strain rate of 6.67 × 10−4 s−1. Especially, a remarkable variation of the electrical property and grain growth were observed in 3Y-TZP during the deformation. The stress exponent ranging within 2~3 indicated that the deformation was dominated by grain boundary sliding. The applied electric current decreased the apparent activation energy Q of the deformation from 465 kJ mol-1 to 315 kJ mol-1, resulting in a transition of the diffusion mechanism from the lattice diffusion to the grain boundary diffusion. These phenomena were mainly attributed to the enhancement of the cation diffusion caused by the electrochemical reduction reaction, which induced by the electric current in oxygen-lean atmosphere.

Cervical cancer is the most common female reproductive tract tumor and is currently the only cancer that can be prevented by vaccination. Early detection and treatment of cervical cancer can be achieved through regular screening for human papillomavirus (HPV). Therefore, in this paper, an electrochemical sensor was designed to detect HPV 16 using a dual signal amplification technique. APTES modified glassy carbon electrode to improve stability. Combining gold nanoparticles and chain amplification reactions for signal amplification purposes. The limit of detection (LOD) was 1.731×10-16 mol/L, and the detection range of this electrochemical sensor was increased in comparison to previous research, with a linear response range from 1.0×10-13 mol/L to 1.0×10-5 mol/L (R2 = 0.99232) for the target detector.In addition, the sensor showed equally good recovery in sophisticated human serum samples. It shows that it has good interference resistance and the designed biosensor can be a powerful and reliable tool for clinical disease diagnosis.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

In this work we successfully prepared a modified cobalt oxide (Co3O4) carbon paste electrode to detect Levofloxacin (LEV). By synthesizing Co3O4 nanoparticles through the chemical coprecipitation method, the electrochemical properties of the electrode and LEV were thoroughly investigated using CV, SWV, EIS, while material properties were scrutinized using ICP-OES, TEM, SEM, and XRD. The results showed that the prepared electrode displayed a better electrocatalytic response than the bare carbon paste electrode. After optimizing SWV, the electrode exhibited a wide linear working range from 1 to 85 μM at pH 5 of BRBS as the supporting electrolyte. The selectivity of the proposed method was satisfactory, with good repeatability and reproducibility, strongly suggesting a potential application for determining LEV in real samples, particularly in pharmaceutical formulations. The practicality of the approach was demonstrated through good recoveries, and the morphology of the materials was found to be closely related to other parameters, indicating that the developed method can provide a cost-effective, rapid, selective, and sensitive means for LEV monitoring. Overall, this project has made significant progress towards developing a reliable method for detecting LEV and has opened up new opportunities for future research in this field.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

In this paper, Akbari-Ganji's and Taylor series methods are applied to find analytical solutions to nonlinear differential equations that arise in an immobilized-cell photobioreactor. Approximate analytical expressions for substrate and product concentrations and both liquid and gas phases for various parameter values are derived using both methods. Efficiency, accuracy, and convergence of the two methods relative to highly accurate numerical methods are investigated to establish reliable profiles of these two methods for solving general nonlinear equations that model various physical phenomena. Numerical simulations are presented to validate the theoretical investigations.

Nowadays, the world's refractory gold ore production accounts for about 30% of the world's total gold, such gold concentrate leaching rate is low, seriously limiting the efficient use of gold resources. The alkaline preoxidation process can improve the leaching rate of this kind of gold deposit, and has a good development and application prospect. So, it is of great significance to study the oxidation and dissolution behavior of pyrite in alka-line environment. In this paper, the oxidation process of gold-bearing pyrite in alkaline electrolyte was studied by electrochemical techniques, and the oxidation products of pyrite electrode in alkaline solution were characterized by XPS，SEM and other analytical methods. The results show that the optimum pH for pyrite electrochemical oxidation dissolution is about 12, and oxidation potential of pyrite should be above 0.8 V. In that proces of alkaline oxidation dissolution of pyrite, part of S element enters the electrolyte in the form of Sx2-, S2O32-, SO32-and SO42-, and a small amount of S element is adsorbed on the surface of the electrode in the form of S0 and becomes a part of the passive layer. Fe element is adsorbed on the surface of electrode in the form of Fe(OH)2, Fe2O3 and Fe2(SO4)3, which becomes the main component of passivation layer. This study provides a theoretical basis and reference data for the chemical preoxidation treatment of sulfide ores.

Metal organic frameworks (MOFs) are used in catalysis due to their high specific surface area and porous structure. The dispersed active sites and limited reaction space render MOFs have the potential for highly selective electrocatalytic CO2 reduction reaction (ECO2RR). Meanwhile, formic acid (HCOOH) is attracting attention as a liquid product with high economic benefits. This review summarizes the MOFs and their derivatives applied for ECO2RR into HCOOH products. The preparation methods of MOFs as electrocatalysts and their unique advantages are discussed. A series of MOFs, and MOFs derivatives obtained by electrochemical reduction or carbonization processes are highlighted, including metal nanomaterials, carbon-based nanocomposites, single-atom catalysts, and bimetallic nanocomposites. Depending on the MOFs building units (metal ions and organic linkers) and the reaction conditions of derivatization, MOFs-based catalysts exhibit rich diversity and controllable modulation of catalytic performance. Finally, the challenges encountered at this stage and the future research directions of MOFs-based catalysts are proposed.

Antibody-mediated targeting is an efficient strategy to enhance the specificity and selectivity of polymer nanomedicines towards the target site, typically a tumor. However, direct covalent coupling of an antibody with a polymer usually results in a partial damage of the antibody binding site accompanied with a compromised biological activity. Here, an original solution based on well-defined non-covalent interactions between tris-nitrilotriacetic acid (trisNTA) and hexahistidine (His-tag) groups, purposefully introduced to the structure of each macromolecule, is described. Specifically, trisNTA groups were attached along the chains of a hydrophilic statistical copolymer based on N-(2-hydroxypropyl)methacrylamide (HPMA), and at the end or along the chains of thermo-responsive di-block copolymers based on N-isopropylmethacrylamide (NIPMAM) and HPMA; His-tag was incorporated to the structure of a recombinant single chain fragment of an anti-GD2 monoclonal antibody (scFv-GD2). Static and dynamic light scattering analyses confirmed that mixing of polymer with scFv-GD2 led to the formation of polymer/scFv-GD2 complexes; those prepared from thermo-responsive polymers formed stable micelles at 37 °C. Flow cytometry and fluorescence microscopy clearly demonstrated antigen-specific binding of the prepared complexes to GD2 positive murine T-cell lymphoma cells EL-4 and human neuroblastoma cells UKF-NB3, while no interaction with GD2 negative murine fibroblast cells NIH-3T3 was observed. These non-covalent polymer protein complexes represent a new generation of highly specific actively targeted polymer therapeutics or diagnostics.

Li-rich manganese-based cathode materials (LRMs) are considered one of the most promising cathode materials for the next generation lithium-ion batteries (LIBs) because of their high energy density. However, there are problems such as capacity decay, poor rate performance, and continuous voltage drop, which seriously limit their large-scale commercial applications. In this work, Li1.2Mn0.54Co0.13Ni0.13O2 coated with Li2MoO4 with unique spinel structure was prepared by wet chemistry method and the subsequent calcination process. The Li2MoO4 coating layer with spinel structure can provide a 3D Li+ transport channel, which is beneficial for improving rate performance, while protecting LRMs from electrolyte corrosion, suppressing interface side reactions, and improving cycling stability. The capacity retention rate of LRMs coated with 3wt% Li2MoO4 increased from 69.25% to 81.85% after 100 cycles at 1C, and the voltage attenuation decreased from 7.06 to 4.98 mV per cycle. The lower Rct also exhibits improved magnification performance. The results indicate that the Li2MoO4 coating effectively improves the cyclic stability and electrochemical performance of LRMs.

Epigenetic modifications are closely related to diseases and physiological health, mainly including DNA methylation, RNA methylation, histone acetylation, and non-coding RNA. Recently, a large amount of research has been conducted on the detection of epigenetic modifications. Electrochemical biosensors, with their low cost, high sensitivity, high compatibility, and simple operation, have been widely used in the detection of epigenetic biomarkers. This review discusses the detection of epigenetic biomarkers using different electrochemical sensing methods. Here we discuss various aspects, including free labels, signal labeling, signal amplification, nano-based electrodes, and the combined use of other methods. By summarizing the existing electrochemical detection methods for epigenetic modifications, this review also proposes the future development trends and challenges for electrochemical biosensors in this field.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

This work aimed to develop an easy-to-use smartphone-based electrochemical biosensor to quickly assess coffee blend's total polyphenol (Phs) content at industrial and individual level. The device is based on a commercial carbon-based screen-printed electrode (SPE) modified with multi-walled carbon nanotubes (CNTs) and gold nanoparticles (GNPs). At the same time, the biotransducer, Laccase from Trametes versicolor, TvLac, was immobilized on the sensor surface by using glutaraldehyde (GA) as cross-linking agent. The platform was electrochemically characterized to ascertain the influence of the SPE surface modification on its performance. The working electrode (WE) surface morphology characterization was obtained by scanning electron microscopy (SEM) and Fourier-transform infrared (FT-IR) imaging. All the measurements were carried out with a micro-potentiostat Sensit Smart by PalmSens connected to a smartphone. The developed biosensor provided a sensitivity of 0.12 μA/μM, a linear response ranging from 5 to 70 μM, and a lower detection limit (LOD) of 2.99 μM. Afterwards, the biosensor was tested for quantifying the total Phs content in coffee blends, evaluating the influence of both the variety and the roasting degree. The smartphone-based electrochemical biosensor performance has been validated though the Folin-Ciocâlteu standard method.

In this study, the preparation of the composite 3% Au/graphite-C3N4 (3% Au/g-C3N4) sensing material was prepared by doping 3% Au onto the surface of graphitic carbonitride (C3N4) for detection pimobendan. By the way of sensing materials characterization, the X-ray diffraction analysis (XRD) and transmission electron Microscope (TEM) were performed. The cyclic voltammetry (CV) was used to measure the concentration and redox properties of pimobendan. It can be seen that when the voltage value is 0.05 V, and a reduction peak was appeared and the pimobendan concentration (0 to 55 μM) has a relationship with the reduction current value. At low concentrations of pimobendan concentration from 0.0 to 0.8 μM, the linearity R2 = 0.9642 with a detection limit of 0.28 μM. A possible pimobendan sensing mechanism on 3% Au/g-C3N4 was proposed.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Aptamers are synthetic single stranded oligonucleotides that exhibit selective binding properties to specific targets, thereby providing as powerful basis for the development of selective and sensitive (bio)chemical assays, such as biosensors. Electrochemical biosensors, utilizing aptamers as biological recognition elements, namely aptasensors, are at the forefront of current research. They exploit the combination of the unique properties of aptamers with the advantages of electrochemical detection with the view to fabricate inexpensive and portable analytical platforms for rapid detection in point-of-care (POC) applications or on-site monitoring. The immobilization of aptamers on suitable substrates is of paramount importance with the aim to retain their functionality and optimize the sensors’ sensitivity. This work describes different immobilization strategies for aptamers on the surface of semiconductor-based working electrodes, including metal oxides, conductive polymers and carbon allotropes. These are presented as platforms with tunable band gaps and different surface morphologies for the preparation of low cost, highly versatile aptasensor devices in analytical chemistry. A survey of the current literature is provided, discussing each analytical method. Future trends envisage for aptamer-based biosensing using semiconductors are also outlined.

Electrochemical Promotion was used to modify the activity and selectivity of a Rh catalyst-electrode in the CO2 hydrogenation reaction. The experiments were carried out in a temperature range of 350-430οC at ambient pressure and at different CO2 to H2 gas feeding ratios (1:2 to 4:1). The only reaction products observed were CO and CH4, both under open and closed-circuit conditions. The CH4 formation rate was found to increase with both positive and negative potential or current application. The CO formation rate followed the opposite trend. The selectivity to CH4 increased under high values of hydrogen partial pressure and decreased at high pressures of CO2. The results demonstrate how Electrochemical Promotion can be used to finely tune activity and selectivity for a reaction of high technical and environmental importance.

We developed a transparent and flexible electrochemical sensor using a platform based on a network of single-walled carbon nanotubes (SWCNTs) for the non-enzymatic detection of hydrogen peroxide (H2O2) released from living cells. We decorated the SWCNT network on a poly(ethylene terephthalate) (PET) substrate with platinum nanoparticles (PtNPs) using a potentiodynamic method. The PtNP/SWCNT/PET sensor synergized the advantages of a flexible PET substrate, a conducting SWCNT network, and a catalytic PtNP, and demonstrated good biocompatibility and flexibility, enabling cell adhesion. The PtNP/SWCNT/PET-based sensor demonstrated enhanced electrocatalytic activity towards H2O2 as well as excellent selectivity, stability, and reproducibility. The sensor exhibited a wide dynamic range of 500 nM to 1 M, with a low detection limit of 228 nM. In addition, Furthermore, the PtNP/SWCNT/PET sensor remained operationally stable even after bending at various angles (15°, 30°, 60°, and 90°) with no noticeable loss of current signal. These outstanding characteristics enabled the PtNP/SWCNT/PET sensor to be practically applied for the direct culture of HeLa cells and the real-time monitoring of H2O2 release by the HeLa cells under drug stimulation.

The growing demands of material longevity in marine environments necessitate the development of highly efficient, low-cost and durable corrosion protective coatings. Although magnesium alloys are widely used in the automotive and aerospace industries, severe corrosion issues still hinder their long-term service in naval architecture. In present work, an epoxy composite coating containing sericite nanosheets is prepared on the AZ31B Mg alloy by one-step electrophoretic deposition method to improve corrosion resistance. Due to the PEI modification, positively-charged sericite nanosheets can be highly orientated in an epoxy coating under the influence of an electric field. The sericite-incorporated epoxy coating prepared in the emulsion with 4 wt.% sericite exhibits the highest corrosion resistance in 3.5 wt.% NaCl solution, as manifested by electrochemical corrosion and long-term immersion tests. The highly-orientated sericite nanosheets in epoxy coating provide excellent barrier effect against corrosive media, thereby significantly improving the long-term anti-corrosion performance of the epoxy coating. This work provides new insight toward the design of lamellar filler/epoxy coatings with superior anticorrosion performance and shows promise in the corrosion protection of magnesium alloys.