The magnetic properties of RCo3B2 compounds, with heavy rare earths, are investigated by using magnetic measurements and electronic structure calculations. The cobalt sublattice magnetizations are very small and antiparallel oriented to rare earths moments. Contributions of cobalt moments to the Curie constants were also shown. The cobalt magnetic behavior has been analyzed in spin fluctuations model. The presence of short-range order above the Curie temperatures in RCo3B2 compounds with R=Tb, Dy, and Ho has been attributed to reminiscent R5d-Co3d interactions.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Chitosan (CS) nanoparticles are under investigation for a wide range of applications in nanomedicine. The structural, molecular and physicochemical properties of chitosan nanoparticles have a direct bearing on their efficacy in drug conjugation and delivery, gene delivery, and tissue engineering. Herein we report on the structural, morphological and molecular properties of chitosan nanoparticles synthesized using the ionic gelation method with the intended purpose of being used for drug delivery. The chitosan nanoparticles (CS-NPs) were prepared in the 0.25 to 1.0% w/v concentration range, whereas separate samples of the 1.0% w/v CS-NPs were also functionalized with polyethylene oxide (PEO) alone and with a diblock copolymer of PEO and polypropylene glycol (PPG). The average size of the CS-NPs was determined from TEM imaging to be in the range of 11.3 to 14.8 nm. The XRD and TEM analyses show that the CS-NPs have semi-crystalline structure with the degree of crystallinity depending upon the nature of synthesis. Our results show that functionalizing the 1.0% w/v CS-NPs with PEO increases the degree of crystallinity whereas functionalizing with the diblock copolymer PEO - PPG results in a significant increase in their degree crystallinity. The CS/TPP concentration (CS:TPP fixed at 1:1 ratio) had no apparent effect on the degree of crystallinity of the CS-NPs. The results from the FTIR analysis confirm incorporation of TPP with CS in the CS-NPs. Additionally, FTIR analysis shows an enhancement of hydrogen bonding that is consistent with the increase in the degree of crystallinity of the CS-NPs.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

The present work reports on the calculated electronic and magnetic structure of the binary Co-Ga system at high Co content. β-CoGa adopts a simple cubic CsCl type structure. Well-ordered CoGa does not exhibit collective magnetism but is a paramagnetic, metallic compound. Neither Co nor Ga deficiency induces magnetic order, however, ferromagnetism is observed for Co-Ga anti-site disorder. The magnetic moment per cell increases up to about 1.2 μB in the completely disordered body centered cubic structure. With increasing Co content, Co1+xGa1−x maintains the CsCl type structure and becomes ferromagnetic. Most important, a discontinuity of the magnetic order with composition is observed at about 10% excess Co, where a change from a low magnetic moment state to a high moment state is observed. This is accompanied by a change in the electronic structure and transport properties. The discontinuity is forced by the increasing exchange splitting related to the localized moment of the additional Co atoms that replace Ga. Subsequently, the magnetic moment increases continuously up to 2.5 μB for x=0.6. For x≳0.6, the structure changes to face centered cubic with random site occupation and the magnetic moment further increases. Above the magnetic discontinuity, the Curie temperature increases linearly with the Co content from the onset of ferromagnetism, until it reaches its maximum in pure Co.

Due to its large hole mobility, Organic Rubrene (C42H28) has attracted research questions on its applications in electronic devices. In this work, extensive first-principles calculations were made to predict some temperature and doping dependent properties of Organic Semi- conductor Rubrene. We use Density Functional Theory (DFT) to investigate the electronic structure, elastic and transport properties of the Orthorhombic phase of the Rubrene compound. The calcu- lated band structure shows the Orthorhombic phase has a direct bandgap of 1.26 eV. From the Vickers hardness (1.080 GPa), our calculations show that Orthorhombic Rubrene is not a super hard material and can find useful application as a flexible semicon- ductor. The calculated transport Inverse Effective Mass and Elec- tronic Fitness Function show that the Orthorhombic Rubrene Crystal Structure is a p-type thermoelectric material at high temperatures.

To harness light-matter interaction at nano-/micro-scale better control tools have to be developed. Here, it is shown that by applying external electric and/or magnetic field, ablation of Si and glass under ultra-short (sub-1~ps) laser pulse irradiation can be controlled via the Lorentz force $\mathbf{F} = e\mathbf{E} + e[\mathbf{v}\times\mathbf{B}]$, where $\mathbf{v}$ is velocity of charge $e$, $\mathbf{E}$ is the applied electrical bias and $\mathbf{B}$ is the magnetic flux density. The external electric E-field was applied during laser ablation using suspended micro-electrodes above glass substrate with an air gap for the incident laser beam. The counter-facing Al-electrodes on Si surface were used to study debris formation patterns on Si. Debris was deposited preferentially towards the negative electrode in the case of glass and Si ablation. Also, an external magnetic field was applied during laser ablation of Si in different geometries and is shown to affect ripple formation. The vectorial nature of the Lorentz force widens application potential of surface modifications and debris formation in external E-/B-fields with potential applications in mass and charge spectroscopes.

The technique of Faraday tomography is a key tool for the study of magnetised plasmas in the new era of broadband radio polarisation observations. In particular, observations at metre-wavelengths provide significantly better Faraday depth accuracies compared to traditional cm-wavelength observations. However, the effect of Faraday depolarisation makes the polarised signal very challenging to detect at metre wavelengths (MHz frequencies). In this work, Faraday tomography is used to characterise the Faraday rotation properties of polarised sources found in data from the LOFAR Two-Metre Sky Survey (LoTSS). Of the 76 extragalactic polarised sources analysed here, we find that all host a radio-loud AGN. The majority of the sources (∼64%) are large FRII radio galaxies with a median projected linear size of 710 kpc and median radio luminosity at 144 MHz of 4 × 10^26 W/Hz. In several cases, both hotspots are detected in polarisation at an angular resolution of ∼20". One such case allowed a study of intergalactic magnetic fields on scales of 3.4 Mpc. Other detected source types include an FRI radio galaxy and at least 8 blazars. Most sources display simple Faraday spectra, however, we highlight one blazar that displays a complex Faraday spectrum, with two close peaks in the Faraday dispersion function.

In this study, we investigate the magnetization behavior of coaxial nanowires fabricated through the sol-gel electrospinning method. Our analysis uncovers a significant reduction in coercivity for CoFe2O4 nanowires when BaTiO3 is used as the shell material, effectively transforming them from hard to soft magnetic. This intriguing behavior is attributed to the magnetization reversal effect at the interface between ferromagnetic and paramagnetic regions, and it is also observed in NiFe2O4 and Fe2O3 nanowires. Surprisingly, introducing a GdBa2Cu3O7 shell induces a similar effect. Additionally, we employ magnetic impedance measurements on the coaxial nanowires, unveiling their potential for magnetic field sensing applications.

The atomic nucleus contains protons and neutrons surrounded by a structured electron cloud. Some combinations of protons and neutrons induce the nucleus to behave like a microscopic magnet, possessing a unique magnitude and orientation known as the nuclear magnetic moment (µ). When the numbers of protons and neutrons are both even then µ=0, but otherwise each nu-clide’s nuclear magnetic moment is unique. A second unique nuclear physical property relates to the nucleon binding energy (BE), which can be thought of as the energy between protons and neu-trons bound within the nucleus. The sequence of stable nuclides increases one nucleon at a time through 36Ar. The binding energy associated with the addition of each successive nucleon (∆BE) through this progression is unique. The hypothesis here is that the unique non-zero magnetic mo-ment and ∆ binding energy of each nuclide derive from its respective microscopic nuclear struc-ture, analogous to the way that the atomic physical properties of an element ultimately derive from its unique electron orbital structure. By extension, the identification of nuclear periodic pat-terns might eventually inform a theory of nuclear structure. The light, stable nuclides through 36Ar were arranged in ascending order according to atomic mass, and their nuclear magnetic mo-ments and binding energies were evaluated for periodic patterns. Fixed-period lengths from 4 through 18 nuclides per period were considered. These fixed periods, each of equal length, were stacked one upon the other and analyzed for vertical trends. The best evidence of periodicity in both µ and ∆BE converges precisely at the fixed 12-nuclide period. Implications for nuclear structure are discussed.

The spin-1/2 quantum transverse Ising model, defined on a ladder structure, with nearest-neighbor and four-spin interaction on a plaquette, is studied by using exact diagonalization and finite-size-scaling procedures. The quantum phase transition between the ferromagnetic and paramagnetic phases has been obtained in the thermodynamic limit. The critical transverse field decreases as the antiferromagnetic four-spin interaction increases, and reaches a multicritical point. However, the exact diagonalization approach was not able to capture the essence of the dimer phase beyond the multicritical transition.

The maturity of tomato fruit is normally characterized by external color and it is often difficult to know when fruit have achieved commercial maturity or become over-mature. The internal structure of tomato fruit change during development and this study investigates the utility of nondestructive measurement of tomato fruit structure as a function of maturity using magnetic resonance imaging (MRI). The objective of this work is to use analysis of internal tomato fruit structural measurements to characterize maturity. Intact cherry tomato fruit were harvested at six different maturity stages. At each stage of maturity, the internal structure of the fruit was measured using a series of 2D magnetic resonance (MR) images. Qualitative and quantitative image analyses were performed to correlate internal fruit structure with maturity. Internal structural changes observed in the pericarp region of the tomato fruit are highly correlated with fruit maturity. MR image information combined with classical analysis techniques provides a more complete understanding of structure and physicochemical changes in tomato fruit during maturation. This study demonstrates that MRI is a useful analytical tool to characterize internal changes in agricultural produce as the produce matures. This technique can be applied to almost any agricultural produce to monitor internal physical changes due to external impact, maturity stage, variation in climate, storage time and condition or other factor impacting quality.

In the Standard Model of elementary particles, the rest mass, magnetic moment and electric charge of the electron are considered to be natural constants. In this article it is proposed that these properties can be calculated in a simple way from the corresponding Planck units using the well-known period doubling phenomenon in nonlinear dynamical systems. Periods corresponding to the values of the electron and positron properties belong to a subset of stable periods. The periodic structures of the rest energy and magnetic moment consist of three internal degrees of freedom, whereas the Coulomb energy of the electric charge consists of four. The number of period doublings for the elementary charge determines the value of the fine structure constant alpha.

TmMgB5O10 spontaneous crystals were synthesized via flux-growth technique from a K2Mo3O10-based solvent. The crystal structure of the compound was solved and refined within the space group P21/n. The first principles calculations of the electronic structure reveal that TmMg-pentaborate is an insulator with an indirect energy band gap of approximately 6.37 eV. Differential scanning calorimetry measurements and powder X-ray diffraction studies of heat-treated solids show that TmMgB5O10 is an incongruent melting compound. A characteristic band of Tm3+ cation corresponding to the 3H6 → 1D2 transition is observed in the photoluminescence excitation spectra of TmMg-borate. The as-obtained crystals exhibit intense blue emission with the emission peaks centered at 455, 479, 667 and 753 nm. The most intensive band corresponds to the 1D2 3F4 transition.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Nereis as a mudflat organism has a variety of uses, in the history of China as a Chinese herbal record, because of its body contains rich amino acids, fatty acids and other nutrients, it can be used for therapeutic treatment and treatment can also be used as health care products. acids, fatty acids and other nutrients, it can be used for therapeutic treatment and treatment can also be used as health care products. In modern times, more and more researchers have studied the protease extract of Nereis as a mudflat organism. In modern times, more and more researchers have studied the protease extracted from the body of nereis and found that there are a variety of functional proteins in nereis, including superoxide dismutase, superoxide dismutase, superoxide dismutase and superoxide dismutase. More and more researchers have studied the proteases extracted from the body of nereis and found that there are a variety of functional proteins in nereis, including superoxide dismutase, adenylate cyclase, glycosidase, and plasminase. In this paper, the functional proteases in the extracts of nereis were summarized, and the functions and characteristics of proteases in nereis were discussed from the perspective of molecular structure.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

Intraband energy transitions of an electron in GaAs/AlGaAs hexagonal quantum well wires in the presence of external electric and magnetic fields are presented. We consider the effects of the revolve of the quantum well wires via a geometric factor that converts the quantum wires straight and symmetric with respect to the z−axis, into a curved wires that no longer has this symmetry. In addition, the influence of having a shallow donor impurity on (off) is calculated. The shape of this quantum string corresponds to the core/shell structure. The energy levels and wave functions of the electron in the heterostructure with a finite potential between the shells are calculated using the effective mass approximation and the finite element method. The calculations of the optical properties are obtained from the compact density matrix and an iterative method. The direction of the applied external fields is parallel (anti-parallel) to the z−direction. The results reveal a significant dependence of the physical properties calculated with the deformation parameter, the dimensions of the quantum well wires and the presence or not of the impurity. The electronic transitions are in a range between 4.90 meV to 41.50 meV under the effect of the electric field, this corresponds to a range of frequencies of optical responses between 1.20 to 10 THz, that is, the mid-infrared. For the magnetic field the range is between 1.24 meV to 14 meV, that is, in frequencies from 0.36 to 3.38 THz, that is, in the far-infrared.

The unfolded band structure and optical properties of Cu-doped KCl crystals were computed by first principles within the framework of density functional theory, implemented in the ABINIT electronic structure package utilizing pseudopotential approximation and a plane-wave basis set. From a theoretical point of view, Cu substitution into pristine KCl crystals requires calculation by the supercell (SC) method. This procedure shrinks the Brillouin zone, resulting in a folded band structure that is difficult to interpret. To solve this problem and gain insight into the effect of copper ions (Cu+) on electronic properties, the band structure of SC KCl:Cu was unfolded to make a direct comparison with the band structure of the primitive cell (PC) of pristine KCl. To understand the effect of Cu substitution on optical absorption, we calculated the imaginary part of the dielectric function of KCl:Cu through a sum-over-states formalism and broke it down into different band contributions by partially making an iterated cumulative sum (ICS) of selected valence and conduction bands. Consequently, we identified those interband transitions that give rise to the absorption peaks due to the Cu+ ion. These transitions involve valence and conduction bands formed by the Cu-3d and Cu-4s electronic states

Prosthetics have come a long way since their inception, and recent advancements in materials science have enabled the development of prosthetic devices with improved functionality and comfort. One promising area of research is the use of auxetic metamaterials in prosthetics. Auxetic materials have a negative Poisson's ratio, which means that they expand laterally when stretched, unlike conventional materials, which contract laterally. This unique property allows for the creation of prosthetic devices that can better conform to the contours of the human body and provide a more natural feel. In this review article, we provide an overview of the current state of the art in the development of prosthetics using auxetic metamaterials. We discuss the mechanical properties of these materials, including their negative Poisson's ratio and other properties that make them suitable for use in prosthetic devices. We also explore the limitations that currently exist in implementing these materials in prosthetic devices, including challenges in manufacturing and cost. Despite these challenges, the future prospects for the development of prosthetic devices using auxetic metamaterials are promising. Continued research and development in this field could lead to the creation of more comfortable, functional, and natural-feeling prosthetic devices. Overall, the use of auxetic metamaterials in prosthetics represents a promising area of research with the potential to improve the lives of millions of people around the world who rely on prosthetic devices.

Waxy rice is one of the most popular traditional crops served as a staple food in China. In this study, the effect of different factors including α-amylase activity, protein, and amylopectin structure on the pasting properties of four waxy rice varieties were investigated. Rice flours treated with AgNO3 solution, DL-dithiothreitol (DTT) or protease, suggested that both α-amylase activity and protein significantly decrease the pasting viscosity of waxy rice flours. Chain length distribution of amylopectin as measured by high performance ion exchange chromatography (HPAEC-PAD) showed that starch with higher ratio of short chain leading to a higher pasting viscosity. X-Ray diffractograms showed that the crystal type of all the four varieties of rice starches were characteristic A-type. Relative crystallinity of each rice starch was further calculated, and a higher crystallization resulted in a higher viscosity. Our study would provide a fundamental knowledge of the relationship between different factors and waxy starch pasting properties, as well as be a reference for controlling the quality of waxy rice starch-based food.

Highly transparent thin films with the chemical formula BaSrMgWO6 were deposited by spin coating using a solution of nitrates of Ba, Sr and Mg and ammonium paratungstate in dimethylformamide with a ratio Ba:Sr:Mg;W=1:1:1:1. XRD, SEM, EDX and XPS investigations evidenced that an annealing at 800 ºC for 1h leaves the structure amorphous with a precipitate on the surface and that a supplementary annealing at 850 ºC for 45 min forms a nanocrystalline structure and dissolves a part of precipitates. It was evidenced a textured double perovskite cubic structure (61.9%) decorated with tetragonal and cubic impurity phases (12.7 %) like BaO2, SrO2 and MgO and an under-stoichiometric phase (24.4%) with the chemical formula Ba2-(x+y) SrxMgyWO5. From transmittance measurements the values of optical band gap were estimated for the amorphous (Eg= 5.15) and nanocrystalline (Eg=4.58 eV) phases. The presence of a lattice disorder was indicated by the high values of Urbach and weak absorption tail energies A decrease in their values was observed and attributed to the crystallization process and cation redistribution.

New analysis regarding the structure of center vortices and their color structure is presented: Using data from gluonic SU(2) lattice simulation with Wilson action a correlation of fluctuations in color space to curvature of vortex fluxes was found. Finite size effects of the S2-homogeneity hint at color homogeneous regions on the vortex surface.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

Optical properties of the cornea are responsible for correct vision, ultrastructure allows optical transparency and biomechanical properties governs the shape, elasticity or stiffness of the cor-nea affecting ocular integrity and intraocular pressure. Therefore, optical aberrations, corneal transparency, structure and biomechanics play a fundamental role in the optical quality of hu-man vision, ocular health and refractive surgery outcomes. However, the convergence of those properties is not yet reported at macroscopic scale within the hierarchical structure of the cornea. This work explores the relationships between biomechanics, structure and optical properties (corneal aberrations and optical density) at macrostructural level of the cornea through dual Placido-Scheimpflug imaging and air-puff tonometry systems in a healthy young adult popula-tion. Results showed convergence between optical transparency, corneal macrostructure and biomechanics.

The review analyzes the studies published mainly in the last 10-15 years, on the synthesis, structure, and sensor properties of semiconductor nanocomposites. Particular attention is paid to the interaction between nanoparticles of the sensitive layer and its effect on the structure, sensitivity, and selectivity of semiconductor sensor systems. Various mechanisms are considered of interaction between nanoparticles in metal oxide composites including incorporation of metal ions of one component into the structure of another, heterocontacts between different nanoparticles, and core-shell systems, as well as their influence on the characteristics of gas sensors. The experimental data and studies on the modeling of charge distribution in semiconductor nanoparticles, which determine the conductivity and sensor effect in one- and two-component systems, are also discussed. It is shown that the model which considers the interactions of nanoparticles best describes the experimental results. Some mechanisms of detection selectivity are considered in the conclusion.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Antimony (Sb) Substitution less than 10 % is examined on a single crystal of a layered superconductor NdO_0.7F_0.3BiS₂. Superconducting transition temperature of the substituted samples decreases with increasing Sb concentration. A lattice constant along the c axis showed a large decrease compared with that along the a axis. Since in-plane chemical pressure monotonically decreases with increasing Sb concentration, the suppression of the superconductivity is well described in terms of the decrease in in-plane chemical pressure.

Unmanned aerial vehicles (UAV) provide an unprecedented capacity to monitor the development and dynamics of tree growth and structure through time. It is generally thought that the pruning of tree crops encourages new growth, has a positive effect on fruiting, makes fruit-picking easier, and may increase yield, as it increases light interception and tree crown surface area. To establish the response of pruning in an orchard of lychee trees, an assessment of changes in tree structure, i.e. tree crown perimeter, width, height, area and Plant Projective Cover (PPC), was undertaken using multi-spectral UAV imagery collected before and after a pruning event. While tree crown perimeter, width and area could be derived directly from the delineated tree crowns, height was estimated from a produced canopy height model and PPC was most accurately predicted based on the NIR band. Pre- and post-pruning results showed significant differences in all measured tree structural parameters, including an average decrease in tree crown perimeter of 1.94 m, tree crown width of 0.57 m, tree crown height of 0.62 m, tree crown area of 3.5 m², and PPC of 14.8%. In order to provide guidance on data collection protocols for orchard management, the impact of flying height variations was also examined, offering some insight into the influence of scale and the scalability of this UAV based approach for larger orchards. The different flying heights (i.e. 30, 50 and 70 m) produced similar measurements of tree crown width and PPC, while tree crown perimeter, area and height measurements decreased with increasing flying height. Overall, these results illustrate that routine collection of multi-spectral UAV imagery can provide a means of assessing pruning effects on changes in tree structure in commercial orchards, and highlight the importance of collecting imagery with consistent flight configurations, as varying flying heights may cause changes to tree structural measurements.

Oligonucleotide conjugates with boron clusters have found applications in different fields of molecular biology, biotechnology, and biomedicine as potential agents for boron neutron capture therapy, siRNA components, and antisense agents. Particularly, closo-dodecaborate anion represents a high-boron containing residue with remarkable chemical stability and low toxicity, suitable for the engineering of different constructs for biomedicine and molecular biology. In the present work, we synthesized novel oligonucleotide conjugates of closo-dodecaborate attached to the 5'-, 3'-, or both terminal positions of DNA, RNA, 2'-O-Me RNA, and 2'-F-Py RNA oligomers. For their synthesis, we employed click reaction with the azido derivative of closo-dodecaborate. The key physicochemical characteristics of the conjugates have been investigated using high-performance liquid chromatography, gel electrophoresis, UV thermal melting, and circular dichroism spectroscopy. Incorporation of closo-dodecaborate residues at the 3'-end of all oligomers stabilized their complementary complexes, while analogous 5'-modification decreased duplex stability. Two boron clusters attached to the opposite ends of the oligomer only slightly influence the stability of complementary complexes of RNA oligonucleotide and its 2'-O-methyl and 2'-fluoro analogs. On the contrary, the same modification of DNA oligonucleotides significantly destabilized DNA/DNA duplex but gave a strong stabilization of the duplex with RNA target. According to CD spectroscopy results, two terminal closo-dodecaborate residues cause a prominent structural rearrangement of complementary complexes with a substantial shift from B-form to the A-form of the double helix. The revealed changes of key characteristics of oligonucleotides caused by incorporation of terminal boron clusters, such as the increase of hydrophobicity, change of duplex stability, and prominent structural changes for DNA conjugates, should be taken into account for the development of antisense oligonucleotides, siRNAs, or aptamers bearing boron clusters. These features may also be used for engineering of developing NA constructs with pre-defined properties.

A full potential all-electron density functional method within generalized gradient approximation is used to investigate the electronic, elastic and transport properties of cubic copper sulphide and copper selenide. The electronic structure suggests metallic behavior with a zero energy band gap for both materials. Elastic property calculations suggest a stiff material with the bulk to shear modulus ratio of 0.35 and 0.44 for Cu2S and Cu2Se respectively. The transport properties were estimated using the Boltzmann transport approach. Seebeck coefficient, electrical conductivity, thermal conductivity, and power factor all suggest a potential p-type conductivity for Cu2S and n-type conductivity for Cu2Se.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

By manipulating the various physico-chemical properties of amino acids, design of peptides with specific self-assembling properties has been emerging since more than a decade. In this context, short peptides possessing detergent properties (so-called “peptergents”) have been developed to self-assemble into well-ordered nanostructures that can stabilize membrane proteins for crystallization. In this study, the peptide with “peptergency” properties, called ADA8 extensively described by Zhang et al., is studied by molecular dynamics for its self-assembling properties in different conditions. In water, it spontaneously forms beta sheets with a β barrel-like structure. We next simulated the interaction of this peptide with a membrane protein, the bacteriorhodopsin, in the presence or absence of a micelle of dodecylphosphocholine. According to the literature, the peptergent ADA8 is thought to generate a belt of β structures around the hydrophobic helical domain that could help stabilize purified membrane proteins. Molecular dynamics is here used to challenge this view and to provide further molecular details for the replacement of detergent molecules around the protein. To our best knowledge, this is the first molecular mechanism proposed for ''peptergency''. In addition, our calculation approach should serve as a predicting tool for the design of beta peptergent with diverse amphipathic properties.

Structural evolution, mechanical and tribological properties of Al-Mg alloy admixed with 5, 10 and 15 vol.% of iron powder using multi-pass friction stir processing (FSP) have been studied. Homogeneous distribution of intermetallic compound (IMC) particles were achieved after 4 FSP passes what resulted in increasing the stir zone hardness and ultimate tensile stress with simultaneous loss in the ductility. The reinforcement of the aluminum alloy matrix with IMCs allowed reducing wear at the same magnitude of friction. Subsurface composite tribological layer was formed on the FSPed samples as a result of rubbing against a steel counterbody.

Electron beam treatment of ZnS:Cu,Br (Cu activator content 0…0.6%wt.) radioluminescent phosphors as well as charge mixture with the electron energy 900 keV and absorbed dose of 600 kGy resulted in a enhancement of brightness up to 80%. The increased brightness is due to increase of content of wurtzite phase relative to sphalerite one with formation of wurtzite/sphalerite nanocomposite structure. Transformation of crystal structure is accompanied with corresponding change in content of active surface centers characteristic for sphalerite and wurtzite phases. A model describing surface centers of ZnS:Cu,Br radioluminescent phosphor is suggested.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

The mechanical properties, structure, and morphology of milled and 3D printed Ti-6Al-4V alloys produced by selective laser melting were investigated in this study. The mechanical properties were investigated by means of nanoindentation, a tensile test, and a three-point bending test. The Atomic Force Microscope (AFM) was used to study the surface topography and roughness of both titanium alloys. The surface structure and phase analysis were studied by a scanning electron microscope (SEM) and through powder X-ray diffraction (XRD). The results from the nanoindentation experiments showed that the 3D-printed sample has higher indentation hardness and modulus than the milled one. The AFM observation of the surface topography of the samples showed that the milled sample has a higher roughness than the 3D-printed one. The tensile test results showed that the 3D printed sample by means of Selective Laser Melting (SLM) technology has about 26% higher tensile strength and smaller elongation than the milled one. The 3-point bending test revealed that the 3D printed Ti-6Al-4V sample has higher flexural strength than the milled one. It was found that the 3D-printed sample has a smaller crystal size than the milled one, which, according to the Hall-Petch relationship, leads to its higher indentation hardness.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Chronic kidney disease patients treated by hemodialysis present a high cardio-vascular morbidity and mortality. There is an imperative need for novel biomarkers in identifying and to offer possible therapeutically intervention in these patients. We performed a prospective observational cohort study on 77 patients in the period October 2021 – October 2023. We measured serum plasma levels of Interleukin 1-Beta, Galectin 3, human suppression of tumorigenicity factor 2, bone morphogenetic protein 2 and fibroblastic growth factor 23 at the inclusion. We evaluated the correlations of these biomarkers with cardiac function and structure evaluated by echocardiography. Mean age was 61.02 (±11.81) years, 45 (56.2%) males and with a dialysis vintage of 4.95 (2.4-7.8) years. Median ejection fraction was 51 (43-54 %) and more than two thirds of the patients presented valvular calcifications. Overall mortality was 22%. Interleukin 1-Beta correlated positively with ejection fraction and global longitudinal strain and negatively with left atrium diameter and left ventricle tele systolic diameter. Galectin 3 values negatively correlated with aortic valve fibrosis and mitral valve calcifications and human suppression tumorigenity factor 2 negatively correlated with mitral valve calcifications. Some of these novel biomarkers could be used to better asses the cardio-vascular disease in patients on maintenance hemodialysis.

To investigate the impact of electrode structure on Electrical Stimulation Therapy (EST) for chronic wound healing, this study designed three variants of flexible microelectrodes (FMs) with Ag-Cu coverings (ACCs), each exhibiting distinct geometrical configurations: hexagonal, cross-shaped, and serpentine. These were integrated with PPY@PDA/PANI (3/6) hydrogel dressings. Comprehensive animal studies, coupled with detailed electrical and mechanical modeling and simulations, were conducted to assess their performance. Results indicated that the serpentine-shaped FM outperformed its counterparts in terms of flexibility and safety, exhibiting minimal thermal effects and a reduced risk of burns. Notably, FMs with metal coverings under 3% demonstrated promising potential for optoelectronic self-powering capabilities. Additionally, simulation data highlighted the significant influence of hydrogel non-uniformity on the distribution of electrical properties across the skin surface, providing critical insights for optimizing EST protocols when employing hydrogel dressings.

Genetic variability in rice breeding program plays the very crucial role. It provides outstanding pool of superior alleles governing better agronomic and quality characters through association mapping. For the understanding of population structure and genetic relationship among the different rice lines is indispensable prior to setting of correlation among dynamic alleles and traits. In the present investigation, genetic diversity and population structure of 116 rice accessions by using 64 polymorphic SSR markers was targeted for the evaluation of the genetic relatedness and diversity. Genotyping assessment based on SSR markers revealed a total of 225 alleles, with an average PIC value of 0.755. The germplasm lines were classified into three distinct subgroups through population structure analysis, utilizing both model and distance-based approaches. AMOVA analysis showed that 11% of the total variation could be attributed to differences between groups, while the remaining 89% of the variation was likely due to differences within groups. The study suggests that the population structure and genetic relatedness should be considered when working with the core collection of 116 rice germplasm lines for association mapping, aiming to establish marker-trait associations.

Prompt removal of misfolded membrane proteins and misassembled membrane protein complexes is essential for membrane homeostasis. However, the elimination of these toxic proteins from the hydrophobic membrane environment has high energetic barriers. Transmembrane FtsH is the only known ATP-dependent protease responsible for this task, unlike other well-studied soluble ATP-dependent proteases. The mechanisms by which FtsH recognizes, unfolds, translocates, and proteolyzes its substrates remain unclear. Here, we report the crystal structures of the Thermotoga maritima FtsH periplasmic domain (PD) in an associative trimeric state at a 1.5-1.95 Å resolution. We also describe the pH-dependent oligomerization states of the isolated PD using dynamic light scattering. These observations help us understand how FtsH recognizes membrane-anchored misfolded proteins.

A new copper(I) complex, [Cu2(L)2dppm](PF6)2 (1) [L = 3-(2-Pyridyl)-5,6-diphenyl-1,2,4-triazine and dppm: Bis(diphenylphosphino)methane] was prepared and characterized by IR, 1H-NMR, 31P-NMR spectroscopy, elemental and thermogravimetric analysis, and single-crystal X-ray diffraction technique. Complex 1 is a dinuclear compound, showing that L and dppm act as tridentate and bidentate chelating ligands, respectively. The two Cu(I) atoms exhibit a distorted tetrahedral coordination sphere embedded in N3P environments. The supramolecular interactions in the solid-state structure are characterized by C−H···N, C−H···F, C-H···π and π···π intermolecular interactions that were analyzed by inspection of the Hirshfeld surface and fingerprint plots. Additionally, the complex was studied experimentally in solution by UV–Vis spectroscopy and cyclic voltammetry; also, theoretical studies with Time-Dependent Density Functional Theory (TD-DFT) were performed. Moreover, the optical and electrochemical properties have been studied, focusing on the band gap. Compound 1 has been used as a co-sensitizer in a dye-sensitized solar cell, showing good activity.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

The way people innovate and create new ideas and bring them to the market is undergoing a fundamental change from closed innovation to open innovation. Why and how do firms perform open innovation? Firms’ open innovation is measured through the levels of firms’ joint patent applications. Next, we analyze network structures and characters of firms’ joint patent applications such as betweenness and degree centrality, structure hole, and closure. From this research, we drew conclusions as follows. First, the structure of collaboration networks has both direct and indirect effects on firms’ innovative performance. Second, in the process of joint patent applications, there is a long tail phenomenon in networks of joint patent applications. Third, the number of patents and International Patent Classification (IPC) subclasses together constitute a meaningful measure of the innovation performance of firms.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

In this review, we summarize recent progress in crystal growth and understanding the influence of crystal structure on the superconductivity in pure and Pb-doped Bi2Sr2CuOy (Bi-2201) materials belonging to the overdoped region of high temperature cuprate superconductors. The crystal growth of Bi-2201 superconductors faces challenges due to intricate materials chemistry and lack of knowledge of corresponding phase diagrams. Historically, a crucible-free floating zone method has emerged as the most promising growth approach for these materials, resulting in high-quality single crystals. This review outlines the described in the literature and the authors' synthesis endeavors, encompassing Pb-doped Bi-2201 crystals, detailed structural characterization of as-grown and post-growth annealed samples, and highlights optimal growth conditions that yield large-size, single-phase, and compositionally homogeneous Bi-2201 single crystals.

Polyurethanes are materials with a strong structure-property relationship. The goal of this research was to study the effect of a polyol blend composition of polyurethanes on its properties using a mixture design and setting mathematic models for each property. Water absorption, hydrolytic degradation, contact angle, tensile stretch, hardness and modulus were studied. Additionally, Thermal stability was studied by thermogravimetric analysis. Area under the curve was used to evaluate the effect of polyol blend composition on thermal stability and kinetics of water absorption and hydrolytic degradation. Least squares were used to calculate the regression coefficients. Models for the properties were significant, and lack of fit was not (P<0.05). Fit statistics suggest both good fitting and prediction. Water absorption, hydrolytic degradation and contact angle were mediated by the hydrophilic nature of the polyols. Tensile strength, modulus and hardness could be regulated by the molecular weight and hydroxyl index of the polyols. Regression of DTG curves from thermal analysis showed improvement of thermal stability with the increase of PCL and PE. An ANOVA test of the model terms demonstrated that three component effects on bulk properties like water absorption, hydrolytic degradation, hardness, tensile strength and modulus, and the PEG*PCL interaction with the contact angle, which is a surface property. Mixture design application allowed for an understanding of the structure-property relationship through mathematic models.

. In this work, two types of nanoporous alumina membranes were prepared using different acids and were tested. Structural features of the samples were investigated by scanning electron spectroscopy and further by different types of fractal dimension estimation methods. Transmission and scattering of accelerated He+ ions were studied in experiments on ion irradiation of dielectric channels based on porous alumina. Ion accelerator was used as a source of the He+ beam with an energy of 1.7 MeV. A scattering of ions was studied by Rutherford backscattering spectrometry. Helium transition through nanoporous alumina at various angles between the normal to the sample and the beam direction were observed. It is shown that the porous structure of anodic aluminum oxide is excellent as a dielectric matrix of nanocapillaries. Owing to the small angle scattering, it allows the transportation of the accelerated charged particles through the dielectric capillaries, and, as a result, localization of high energy ion irradiation effects. Additionally, according to the transmission UV-Vis spectra the energy gaps of samples obtained were calculated.

A series of novel N-n-butyl-1,8-naphthalimide derivatives were synthesized via a three-step reaction involving nucleophilic substitution and acylation. All of the compounds were characterized by IR, ¹H NMR, ¹³C NMR, MS, and elemental analysis, and the crystal structure of N-n-butyl-4-[N’,N’-bis(2`,4`-dichlorobenzoyl)ethylamino]-1,8-naphthalimide was determined. The π-π stacking interactions and hydrogen bonds between the two molecular core planes (naphthalimide ring) and the van der Waals forces between the flexible n-butyl groups resulted in a 3D long-chain structure. The UV-vis and fluorescence properties of the title compounds were investigated. The results indicated that the monosubstituted 1,8-naphthalimide derivatives bearing an electron-donating group on the benzene ring or a structure with a larger conjugative effect exhibited enhanced fluorescence properties.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

This article has been studied the synthesis of a new derivative of the known alkaloid cytisine contained in the seeds of plants of Cytisus laburnum L. and Thermopsis lanceolata R.Br., both of the Lugiminosae family. The new compound has been obtained from two biologically active compounds such as isoxazole and cytisine. It has been demonstrated that the reaction led to the single-stage method under very mild conditions to obtain some 4-[(3,5-dimethyl-1,2-oxazole-4-yl)sulfonyl]amides. This class of compounds is promising to obtain the new biologically active compounds. This article has examined in detail a structure with using the 1H and 13C NMR and two-dimensional NMR spectroscopy of COSY (1H-1H), HMQC (1H-13C) and NMVS (1H-13C). As a result, the homo- and heteronuclear spin-spin couplings should be established. The X-ray diffraction analysis has determined the spatial structure of a new derivative based on cytisine alkaloid. Thus, its hemorheological activity has been studied.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

We review time expansion wave theory and refine our model showing it to accurately match observed cosmological luminosity data. The theory augments general relativity to create a container within which quantum effects can be explained by treating time as an artefact of a fourth spatial dimension that we observe as the expansion of the universe. This leads us to explain mass creation, the speed of light limit, gravity, black holes without singularities and other macroscopic effects. Our model leads to an expansion velocity of 6.87 0.36 × 106 ms-1, which results in a Hubble expansion rate constant of 71.3 3.7 km/s/Mpc. Because of the finite window of time in which we exist, an extra a degree of freedom is available leading to interesting interpretations at the subatomic level. At this size range, then a spin is allowed within the time dimension explaining why wave particle duality occurs and explains the electromagnetic force and other quantum mechanical properties. It provides a solution to the double slit conundrum and can explain how quantum entangled partners can behave in a quantum way and pass seemingly time-defying information. The potential quantitative origin of the fine structure constant which governs the size of the electromagnetic force is also strongly indicated by this theory.

We report the results of the characterization of local Monte Carlo (MC) dynamics of an equilibrium bond fluctuation model polymer matrix (BFM), in time interval typical for MC simulations of non-linear optical phenomena in host-guest systems. The study contributes to the physical picture of the dynamical aspects of quasi-binary mosaic states characterized previously in the static regime. The polymer dynamics was studied at three temperatures (below, above and close to the glass transition), using time-dependent generalization of the static parameters which characterize local free volume and local mobility of the matrix. Those parameters play the central role in the kinetic MC model of host-guest systems. The analysis was done in terms of the probability distributions of instantaneous and time-averaged local parameters. The main result is the characterization of time scales characteristic of various local structural processes. Slowing down effects close to the glass transition are clearly marked. The approach yields an elegant geometric criterion for the glass transition temperature. A simplified quantitative physical picture of the dynamics of guest molecules dispersed in BFM matrix at low temperatures offers a starting point for stochastic modeling of host-guest systems.

: The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating technique was employed. Pre-crystallization was achieved by annealing the films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dissolve the perovskite film. Subsequently, residual solvent was removed through spin coating. The mor-phological analysis of the perovskite film surface after recrystallization at temperatures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was confirmed by the peaks observed in the X-ray diffraction patterns.

Computer simulation of normal and diseased human heart activity requires a 3D anatomical model of the myocardium, including myofibres. For clinical applications, such a model has to be constructed based on routine methods of cardiac visualisation such as sonography. Symmetrical models are shown to be too rigid, so an analytical non-symmetrical model with enough flexibility is necessary. Based on previously made anatomical models of the left ventricle, we propose a new, much more flexible spline-based analytical model. The model is fully described and verified against DT-MRI data. We show a way to construct it on the basis of sonography data. To use this model in further physiological simulations, we propose a numerical method to utilise finite differences in solving the reaction-diffusion problem together with an example of scroll wave dynamics simulation.

We introduce new metric structures on a smooth manifold (called “weak" structures) that generalize the almost contact, Sasakian, cosymplectic, etc. metric structures (φ,ξ,η,g) and allow us to take a fresh look at the classical theory and find new applications. This assertion is illustrated by generalizing several well-known results. It is proved that any Sasakian structure is rigid, i.e., our weak Sasakian structure is homothetically equivalent to a Sasakian structure. It is shown that a weak almost contact structure with parallel tensor φ is a weak cosymplectic structure and an example of such a structure on the product of manifolds is given. Conditions are found under which a vector field is a weak contact vector field.

The review explores the therapeutic potential of mangrove plants as sources of bioactive compounds, particularly focusing on their anti-inflammatory properties. Mangroves, found in tropical and sub-tropical tidal coasts, exhibit unique ecological and biological activities. The review compiles and examines 136 research findings published between 1982 and 2018, with 41 studies specifically addressing the anti-inflammatory properties of mangroves in Indian coastal regions, including the Andaman and Nicobar Islands. It summarizes the chemical structures, molecular weights, formulas, solvents, and biological activities of these mangroves, as reported by various researchers over time. The data underscore the significant potential of tropical Indian mangroves in anti-inflammatory applications. However, a notable research gap exists regarding the extraction of bioactive compounds from mangrove species in the Andaman and Nicobar Islands compared to other regions such as Gujarat, Maharashtra, Goa, Karnataka, Kerala, Tamil Nadu, Andhra Pradesh, Odisha, West Bengal, and Puducherry. Overall, the compilation provides valuable insights into mangrove-based studies for drug discovery research, emphasizing the need for further exploration and exploitation of these natural resources.

The intestinal microbial community of aquatic animals is closely related to the environment and thus affects the health of aquatic animals. Here we investigated annual variation of intestinal bacteria community structures of Ruditapes philippinarum cultured using two different methods, bottom sown and raft hanging. Bacterial diversity of seawater and sediment in different seasons was examined as well. Correlation between R. philippinarum intestinal bacteria community structures and environmental factors was analyzed. The results showed that in the two aquculture areas where R. philippinarum was differentially cultured, bacteria community structure of seawater and sediment both altered with seasons. However, neither seasonal changes nor difference in culture methods could significantly affect the intestinal bacteria community structures of R. philippinarum. Additionally, in terms of the alpha diversity of intestinal bacteria communities, there was no significant difference in R. philippinarum cultured using the two methods. For benthic cultured clams, alpha diversity of the intestinal bacterial communities was often higher than that of the environmental bacterial communities. For raft hanging cultured calms, Alpha diversity of the intestinal bacterial communities was normally comparable with that of the environmental counterparts. Beta diversity analysis showed that the intestinal bacterial community structure of R. philippinarum was mainly determined by both deterministic and stochastic processes. Correlation analysis showed that the intestinal bacterial community structures of R. philippinarum were determined by a variety of environmental factors. For clams collected from the benthic culture area, the intestinal bacterial structure was more correlated with the physicochemical properties of sediment in comparing with those of seawater. For clams collected from the raft-culture area, the intestinal bacterial structure was mainly determined by the phsicochemical characteristics of seawater. This study helps us to better understand the bacterial community structure in complex aquaculture ecosystems, providing a reference for healthy shellfish aquaculture and ecosystem protection in aquaculture area.

The study of rare diseases is important not only for the individuals affected but also for the advancement of medical knowledge and a deeper understanding of human biology and genetics. The wide repertoire of structural information now available from reliable and accurate prediction methods provides the opportunity to investigate the molecular origins of most of the rare diseases reviewed in the Orpha.net database. Thus, it has been possible to analyze the topology of the missense mutations found in the 2,535 proteins involved in Mendelian rare diseases (MRD), which form the database for our structural bioinformatics study. The amino acid substitutions responsible for MRD show different mutation site distributions at different three-dimensional protein depths. We then predicted the depth-dependent effects of mutations for the 20,248 pathogenic variants that are present in our database. The results of this structural bioinformatics investigation are relevant, as they provide additional clues to mitigate the damage caused by MRD.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

Crystal structures of simple metals and binary alloy phases based on the face-centered cubic (fcc) structure are analyzed within the model of Fermi sphere – Brillouin zone interactions to understand the stability of original cubic structure and derivative structures with distortions, superlattices and vacancies. Examination of the Brillouin-Jones configuration in relation to the nearly-free electron Fermi sphere for several representative phases reveals significance of the electron energy contribution to the phase stability. Representation of complex structures in the reciprocal space clarifies their relationship to the basic cubic cell.

In this study composite with alternate layers of 5056 and 1580 alloys was manufactured by wire arc additive manufacturing technology. It is shown that increased strength characteristics of composite material can be obtained due to deformation treatment by high-pressure torsion (HPT) technique. The microstructure and mechanical properties of the HPT-processed material in different structural states were investigated. The HPT-processed material exhibits high value of ultimate tensile strength (~ 770 MPa) but low ductility. Short-term annealing at 250 oС and additional deformation by HPT to 0.25 of revolution at room temperature resulted in a slight decrease in material’s strength to ~ 700 MPa but provided ductility ∼ 9%. Physical mechanisms to improve plasticity in correlation with microstructure evolution is discussed.

The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

Many studies discuss carbon-based materials because of the versatility of its element. They include different opinions for scientific problems and discuss fairly at convincing and compelling levels within the scope and application. A gas-state carbon atom converts into various states depending on its conditions of processing. The electron transfer mechanism in the gas-state carbon atom is responsible to convert it into various states, namely, graphite, nanotube, fullerene, diamond, lonsdaleite and graphene. The shape of ‘energy trajectory’ enables transferring electrons from the left- and right-sides of an atom is like a parabola. That ‘energy trajectory’ is linked to states (filled state and suitable nearby unfilled state) where force-exertion along the poles of transferring electrons is remained balance. So, the mechanism of originating different states of a gas-state carbon atom is under the involvement of energy first. This is not the case for atoms executing confined inter-state electron-dynamics as the force is involved first. Graphite-, nanotube- and fullerene-state atoms ‘partially evolve partially develop’ (form) their structures. These possess one-dimensional, two-dimensional and four-dimensional ordering of atoms, respectively. Their structural formation also comprises ‘energy curve’ having a shape-like parabola. Transferring suitable filled state electron to suitable nearby unfilled state is under a balance force exerting along the poles. The graphite structure under only attained-dynamics of atoms can also be formed but in two-dimension. Here, binding energy between graphite-state carbon atoms is for a small difference of exerting forces along their opposite poles. Structural formation in diamond, lonsdaleite and graphene atoms involve energy to gain required infinitesimal displacements of electrons through which they maintain orientationally-controlled exerting forces along dedicated poles. In this study, the growth of diamond is found to be south to east-west (ground) where atoms bound ground to south. Thus, diamond atoms merge for a tetra-electron ground to south topological structure. Lonsdaleite atoms merge for a bi-electron ground to just-south topological structure. The growth of graphene is found to be north to ground where atoms bound ground to north. Thus, graphene atoms merge for a tetra-electron ground to north topological structure. Glassy carbon exhibits layered-topological structure where, tri-layers of gas-, graphite- and lonsdaleite-state atoms successively bind in repetitive order. Nanoscale hardness is also sketched based on different force-energy behaviors of different state carbon atoms. Here, structure evolution in each carbon state atom explores its own science.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

Intrinsically disordered proteins mediate crucial biological functions through their interactions with other proteins. Mutual synergistic folding (MSF) occurs when all interacting proteins are disordered, folding into a stable structure in the course of the complex formation. In these cases, the folding and binding processes occur in parallel, lending the resulting structures uniquely heterogeneous features. Currently there are no dedicated classification approaches that would take into account the particular biological and biophysical properties of MSF complexes. Here we present a scalable clustering-based classification scheme, built on redundancy-filtered features that describe the sequence and structure properties of the complexes, and the role of the interaction, which is directly responsible for structure formation. Using this approach, we define six major types of MSF complexes, corresponding to biologically meaningful groups. Hence, the presented method also shows that differences in binding strength, subcellular localization, and regulation are encoded in the sequence and structural properties of proteins. While current structure classification methods can also handle complex structures, we show that the developed scheme is fundamentally different, and since it takes into account defining features of MSF complexes, it serves as a better representation of structures arising through this specific interaction mode.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

In crystal structure prediction, Newton's second law can always be applied to particles (atoms or ions) in a cell to determine their positions. However the values of the period vectors (crystal cell edge vectors) should be determined as well. Here we applied the dynamical equations of period vectors derived recently based on Newton's laws (doi:/10.1139/cjp-2014-0518) for that purpose, where the period vectors are driven by the imbalance between the internal and external pressures/stresses. For equilibrium states, they became equations of state, which essentially turn out the equilibrium conditions of crystals from mechanical point of view. For external pressure, by ignoring some effects, they reduced to the Mie-Gruneisen equation. Since the internal stress has both a full kinetic energy term and a full interaction term, the influences of both external temperature and stress/pressure on crystal structures can be calculated, then thermodynamical properties and processes were presented. Contrary to usual ideas, the equations show that pure harmonic vibrating phonons can result in thermal expansion in crystals when the external temperature is changed. Finally, crystal system collapse due to temperature and/or stress/pressure change was discussed.

This research program investigated the effects of layer thickness (50 and 100 microns) on the microstructure and mechanical properties of electron beam powder bed fusion (EBPBF) additive manufacturing of Inconel 625 alloy. The as-built 50 and 100 micron layer thickness components were also heat treated at temperatures above 1100 oC, which produced a recrystallized grain structure containing annealing twins in the 50 micron layer thickness components, and a duplex grain structure consisting of islands of very small equiaxed grains dispersed in a recrystallized, large-grain structure containing annealing twins. The heat treated component microstructures and mechanical properties were compared with the as-built components in both the build direction (vertical) and perpendicular (horizontal) to the build direction. Vickers microindentation hardness (HV) values for the vertical and horizontal geometries averaged 227 and 220 for the as-built 50 and 100 micron layer components, and 185 and 282 for the corresponding heat treated components. The yield stress values were 387 MPa and 365 MPa for the as-built layer horizontal and vertical 50 micron layer geometries, and 330 MPa and 340 MPa for the as-built 100 micron layer components. For the heat treated 50 micron components, the yield stress values were 340 and 321 MPa for the horizontal and vertical geometries, and 581 and 489 MPa for the 100 micron layer components, respectively. The elongation for the 100 micron layer as-built horizontal components was 28% in contrast to 65% for the corresponding 100 micron heat treated layer components, an increase of 132% for the duplex grain structure. However, the coarse grains containing annealing twins and the equiaxed small grain islands in the duplex structure for the heat treated components contained continuous carbides in the grain boundaries, and this may indicate sensitization and a reduction in corrosion resistance. These findings point to the potential mechanical property advantage for heat treatment of Inconel 625 alloy 100 micron layer thickness components fabricated by EBPBF.

The increasing demand for transporting people and goods, rail system is needed for enhancement. An architectural design of train station can significantly impact investment from any government. However, a proper guideline for designing the train station in tropical climate is not publicized. This review examine railway station design through an analysis of student design theses in Thailand, from 1983 to 2022. Furthermore, the building analyses on architectural design theory were done in terms of service area, form, entrance structure, roof structure, style, and design development. The analysis reveals curved and gable roofs are most frequent, followed by 3D curved roofs. HSR stations' main entrances are designed to represent local culture and save walking distance. Curved and gabled porticos provide the most extravagant main entryway, a feeling of grandeur and beauty. A public building's overlapping portico or curving gabled portico lends majesty and refinement to its façade. Architects and designers strive to make buildings more attractive and practical. Besides, university-designed stations prioritize conceptual design and functional space over cost. Finally, railway station design should prioritize transparency, connectivity, movement, and cost- and time-efficiency. Research gaps are identified, such as designing user-friendly for thermal comfort and design-for-all the railway station in tropical climate, are critical for future evaluation.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

Piezoelectric properties are of significant importance to medical ultrasound, actuators, sensor, and countless other device applications. The mechanism of piezoelectric properties can be deeply understood from structure evolutions. In this paper, we report a diagram of structure evolutions of the Pb(Zn1/3Nb2/3)0.91Ti0.09O3 (PZN-9PT) single crystal with excellent piezoelectric properties among the orthorhombic, tetragonal, and cubic phases with temperature increasing from room temperature to 220 C. Through fitting the temperature dependence XRD curves with Gauss and Lorenz functions, we obtained the evolutions of the content ratio of three kinds of phases (orthorhombic, tetragonal and cubic) and the lattice parameters of the PZN-9PT system with the changes of temperature. The XRD fitting results together with Raman and dielectric spectrums show that the phase transitions of PZN-9PT are a typical continuous evolution process, very similar to the phase transition of paraffin from solid to liquid. Additionally, resonance and anti-resonance spectrum show excellent piezoelectric properties of the crystals, which probably originate from the nano twin domains, as demonstrated by the TEM images. Of particular attention is that the thickness electromechanical coupling factor kt is up to 72%.

Abstract: : 2,3-dihydro-5,6,7,8-tetranitro-1,4-benzodioxine (TNBD), molecular formula =C8H4N4O10 is a completely nitrated in aromatic ring 1,4-benzodioxane derivative. The con-venient method of TNBD synthesis was developed (yield=81 %). The detailed structure of this compound has been investigated by X-ray crystallography. The results of differential thermal analysis (DTA) obtained with twice re-crystallized material showed onset at 247 and isoterm at 288 0C, with further total degradation at 300 0C. The experimental density 1,85 g/cm3 of TNBD was determined by X-ray crystallography. The spectral properties of TNBD (NMR, FT-IR, Ra-man) were explored. The detonation properties of TNBD calculated by EXPLO 5 code was slightly superior in comparison to standard high energy material - tetryl (detonation velocity of TNBD - 7727 m/s; detonation pressure - 278 kbar; tetryl – 7570 m/s and 226.4 kbar at 1.614 g/cm3, or 260 kbar at higher density - 1.71 g/cm3. The obtained preliminary results might suggest TNBD can be a potential thermostable high energy and density material (HEDM).

Population is the main driver of land systems and environmental change. However, the population is usually treated as a variable that only considers the population number, and the multidimensional population structure is largely ignored. There has been a systematic transition of population structure in the past several decades, such as the changing household structure, the increasing aging population and divorce rate, and human migration. All these have direct or indirect impacts on land use and environmental issues. Here, we will take China as an example to examine the relationship between household dynamics and land use change in China by exam-ining changes in household structure and land use change in China between 1980 and 2020. The results show:1) the number of households increased by 130.95% from 1980 to 2020, while the population only increased by 42.83%. The size of households decreased from 4.41 to 2.92 in China from 1982 to 2020. The household dynamics vary from province to province, which is affected by urbanization rate and economic development. 2) Birth rates, divorce rates, population aging, and migration all affect household structure, which directly or indirectly affects changes in land use systems. 3) The changes in China's land use are interlinked and interact with changes in household structure, evident in the increase in residential land use and the abandonment of arable land. The rising household number increased the area of urban and rural settlement, leading to the fragmentation of cultivated land and the reduction of ecological land. To regulate land use change for sustainable development, future land use planning should take into effect of household dynamics, and reduce the negative effects of household dynamics on land systems and environmental change.

A monocular vision pose estimation and identification algorithm used on a small spacecraft for future orbital servicing is studied in this paper. A tracker spacecraft equipped with a short-range vision system is proposed to recover the 3D structural model of a space target in orbit and automatically identify its solar panels and main body using only visual information from an onboard camera. The proposed reconstruction and identification framework is tested using structure-from-motion and point cloud identification methods. The Efficient Perspective-n-Points (EPnP) descriptor is used for pose estimation. Triangulated points are used for component segmentation by means of orientation histogram descriptors. Experimental results based on laboratory images of a spacecraft model show the effectiveness and robustness of our approach.

To estimate the progressive collapse resistance capacity of a multi-column frame tube structure with the assembled truss beam composite floor (ATBCF), the pushdown analysis, and the nonlinear dynamic analysis as well, are conducted for such a structure by using the alternate load path (ALP) method. The bearing capacities of the remaining structures at three different work conditions, which are the side middle column failure, the edge middle column failure, and the corner column failure, are individually studied, and the collapse mechanism for the remaining structures is analyzed from the aspects of the internal force redistribution and the failure mode of the second defense line. Simultaneously, the influence of the column failure time on the dynamic response of the remaining structure and the dynamic amplification coefficient are discussed. The results show that the residual bearing capacity of the remaining structure with the bottom corner column failure is higher than that of the one with the side or edge middle column failure, while the latter has a stronger plastic deformation capacity. When the ALP method is adopted to operate the progressive collapse analysis, it is reasonable to take the column failure time as 0.1 times of the first-order vertical vibration period of the remaining structure, and it is suitable to set the dynamic amplification coefficient as of 2.0, which is the ratio of the maximum dynamic displacement to the static displacement of the remaining structure under the transient loading condition.

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

DNA Topoisomerase IIa (Top2A) is a nuclear enzyme that is a cancer drug target, and there is interest in identifying novel sites on the enzyme to inhibit cancer cells more selectively and to reduce off-target toxicity. The C-terminal domain (CTD) is one potential target, but it is an intrinsically disordered domain, which prevents structural analysis. Therefore, we set out to analyze the sequence of Top2A from 105 species using bioinformatic analysis including the PSICalc algorithm, entropy analysis, and other approaches. Our results demonstrate that large (10th-order) interdependent clusters are found including non-proximal positions across the major domains of Top2A. Further, CTD-specific clusters of 3rd, 4th, and 5th-order were identified that included positions that had been previously analyzed via mutation and biochemical assays. Some of these clusters coincided with positions that when mutated either increased or decreased relaxation activity. Finally, sites of low entropy (i.e., high information content) were identified and mapped as key positions in the CTD. Included in the low entropy sites are phosphorylation sites and charged positions. Together, these results help to build a clearer picture of the critical positions in the CTD and provide potential sites/regions for further analysis.

This study explores the capital structure determinants of Korean firms over an extensive period (1995-2021), encompassing both stable and crisis conditions. Employing a dynamic panel data model and the Generalized Method of Moments (GMM) estimation, we address the endogeneity issue introduced by the inclusion of lagged dependent variables. Our research integrates firm-specific internal factors with macroeconomic external variables to provide a comprehensive understanding of the influence of varying economic environments on capital structure. Our study suggests that in times of economic stability, the capital structure decisions of a firm are more influenced by internal factors such as profitability. However, in periods of economic downturns, it's the external macroeconomic market conditions that tend to have a greater impact on these decisions. It's also noteworthy that both book leverage (BL) and market leverage (ML) exhibit quicker adjustments during stable periods as opposed to periods of crisis. This indicates a higher agility of firms in adapting their capital structures in stable normal conditions. Our findings contribute to existing literature by offering a holistic view of capital structure determinants in Korean firms. They underscore the necessity of adaptable financial strategies that account for both internal dynamics and external economic conditions. This study fills a gap in current research, presenting new insights into the dynamics of capital structure in Korean firms and suggesting a multifaceted approach to understanding capital structure in diverse economic contexts.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

CoO-ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the CBD method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, low and high-resolution of scanning electron microscopy, and transmission electron microscopy. The as-synthesized hierarchical nanocorn skeleton-like structure of CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance of 1136 F/g at a current density of 3 A/g with outstanding cycling stability, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO (CO), ZnO (ZO), CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274, 383, 240 and 537 F/g, respectively). This superior capacitance was attributed to the ideal surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Research on titanium oxo complexes (TOCs) are usually focused on their structure and photocatalytic properties. Findings from these investigations spurred our interest in exploring also their potential biological activities. In this study, we focused on the synthesis and structure of a compound with the general formula [Ti8O2(OiPr)20(man)4] (1), which was isolated from the reaction mixture of titanium(IV) isopropoxide with mandelic acid (Hman) in a molar ratio of 4:1. The structure (1) was determined using single-crystal X-ray diffraction, while spectroscopic studies provided insights into its physicochemical properties. To assess the potential practical applications of (1), its microcrystals were incorporated into a polymethyl methacrylate (PMMA) matrix, yielding composite materials of the type PMMA + (1) (2 wt.%, 5 wt.%, 10 wt.%, and 20 wt.%). The next stage of our research involved the antimicrobial activity evaluation of the obtained materials. Investigations carried out demonstrated antimicrobial activity of pure (1) and its composites (PMMA + (1)) against both Gram-positive and Gram-negative strains. Furthermore, MTT tests conducted on the L929 murine fibroblast cell line confirmed the lack of cytotoxicity of these composites. Our study identified (1) as a promising antimicrobial agent, also for producing composite coatings.

In recent decades, perovskite-type compounds (ABB′O3) have been exhaustively studied due to their unique ferroelectric properties. In this work, a systematic study aiming to prepare fine particles in the binary system SrZrO₃–SrTiO₃ was conducted under hydrothermal conditions in a KOH (5 M) solution at 200 °C for 4 h under a constant stirring speed of 130 rpm. The precursors employed were SrSO₄ powder (&lt; 38 μm size) and coprecipitated hydrous gels of Zr(OH)₄•9.64 H₂O (Zr-gel) and Ti(OH)₄•4.5H₂O (Ti-gel), which were mixed according to the stoichiometry of the SrZr_1-xTixO₃ in the compositional range of 0.0&gt;x&gt;100.0 mol% Ti⁴⁺. The XRD results revealed the formation of two crystalline phases rich in Zr⁴⁺, an orthorhombic structured SrZr0.93Ti0.07O3 and a cubic structured SrZr0.75Ti0.25O3 within the compositional range of 0.1–0.5 mol of Ti4+. A cubic perovskite-structured solid solution, SrTi1-xZrxO3, was preferentially formed within the compositional range of 0.5&gt;x&gt;0.1 mol% Ti⁴⁺. The SrZrO₃ and SrZr_0.93Ti_0.07O₃-rich phases had particle sizes averaging 3 m with a cubic morphology. However, a remarkable reduction in the particle size occurred on solid solutions prepared with hydrous Ti-gel over contents of 15 mol% Ti⁴⁺ in the reaction media, resulting in the formation of nanosized particles agglomerates with cuboidal shape self-assembled via a 3D hierarchical architecture, the sizes of these particles varied in the range between 141.0–175.5 nm. The limited coarsening of the particles is discussed based on the Zr-gel and Ti-gel dehydration capability differences that occurred under hydrothermal processing.