This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

Aeromagnetic compensation plays a vital role in geomagnetic navigation and has received considerable attention throughout last few decades. Classical aeromagnetic compensation methods based on the Tolles–Lawson (T-L) model are mainly aimed at permanent, induced, and eddy-current magnetic interferences of aircraft platform, which ignores other stray magnetic field interference on the platform including the interferences caused by on-board electronic (OBE) systems. In order to cooperate with TL model, magnetometers are usually required to be installed on the extension rod outside the cabin, which is widely applied to geophysical magnetic survey. In order to ensure safety and reduce the cost of platform modification in geomagnetic navigation, it’s necessary to place magnetometers inside the cabin. It also further exacerbates the magnetic interferences and improves the difficulty of magnetic compensation. In this paper, a modified aeromagnetic compensation method is proposed, and the in-cabin OBE interferences are respectively modelled to be proportional to the currents and their temporal variations of different electronic devices. To ensure that modified model adapts to strong OBE interference in the cabin, a cut-off frequency determination method based on curvature calculation and a feature selection method based on correlation calculation are proposed. The cut-off frequency determination method helps to select passband filter which suitable for in-cabin OBE interference. The feature selection method can help to effectively select current and voltage inputs for modified model. In addition, principal component analysis (PCA) is adopted to reduce multicollinearity which is intensified by the extension of OBE interferences in coefficient-estimating. Experiments on public dataset are conducted to illustrate the effectiveness of the proposed method, and the best compensation result achieved 1.71nT of root mean square error (RMSE).

Corporate governance is developing rapidly in many countries across the world. In this article, the existing state of corporate governance in Jordan is examined. Jordan does not have a corporate governance code per se. The article reveals that overall Jordan has in place some of the features of corporate governance best practice, but that there remains further progress to be made in areas such as independence of directors, compensation, and correlation between shareholding and entitlement to seats on the board. The article recommends legal reforms in order to enhance corporate governance in Jordan.

In 2013, the CMA at the İstanbul Stock Exchange increased the weight assigned to the Board of Directors component of its Corporate Governance Index to 35% from the previous 25%. Interpreting this as a recognition of the increasing vital role of the board, this study seeks to enhance the work of Abdıoğlu and Kılıç (2015) by putting more focus on the role of women in the boards and the effect of the busy chairman as well as the presence of outside directors on the effectivity of the Board. (The general business structure is associated with family owned groups and holdings which results into a network of intertwined board membership and cases of multiple directorship where, one board chairman can hold the same position or any directorship in as many as ten firmshence the busy chairman). I employ a different method of evaluating performance (EVA) together with the accounting measures of ROE and ROA (as opposed to the overused Tobin’s Q), which I regress against the Board Index to be created. The focus is on firms on the BIST 100 index (excluding financial) between 2009 and 2013. The results reveal that the BINDEX has a significant and positive relationship with firm performance as measured by EVA. A second model reveals no relationship between the BINDEX and firm ROA, similar to the results of Kiliç and Abdioğlu (2015). ROA however has a positive relationship with the proportion of female directors in the board, as earlier reported by LückerathRovers (2013). Another model using ROE as the proxy for performance registers a significant negative relationship with the index. The contradiction obtained in the results from these three models underscore the importance choosing the right methods when estimating the performance of a firm.

Considering the actual world economical trends, one of the most important questions is now and in the future: how to reduce power consumption of electronic systems. Since the invention of computers, the electrical energy consumption step by step increased. Now when not only computers, but electric vehicles, robots, automation, and unmanned aerial vehicles play a very important role of our life, the main problem of system designers is how to reduce energy consumption in these systems. But also the existing already working systems must be revised in order to decrease their electric power consumption. The importance of this subject (energy control) shows that a huge number of research publications and survey papers deal with it. Just focusing on the last one or two years (2021 and 2022) the search hit 221000 titles (103000 hits only in 2022). Analyzing all the research areas is almost impossible, but focusing on some important research subjects, where one of the main topic is “energy saving methods” can give an overview about the subject. The paper focuses on the area of industrial robotic systems, electric vehicles, and embedded systems.

Sailing sports are experiencing a period of radical innovations. Traditional displacing monohulls have always been the reference for yachting in the past, but the continuous quest for performances has generated many variations and many convergences with surprising results. On the aerodynamic side conventional soft sails have been sometime replaced by rigid wings, but the biggest innovation has been the use of traction kites as a propulsion device. On the hydrodynamic side we have seen the rapid growth of hydrofoils, an old concept that is having a rebirth. Probably the most remarkable expression of innovation and integration between concepts having different roots is the hydrofoil kite-board, point of encounter of the traditional wave surfing, the traction kite innovation and the hydrofoil technology. Hydrofoil kite-board can reach speeds up to 3 times the wind speed, are at least one order of magnitude cheaper than any boat with comparable performances, easy to manage and races are spectacular. Hydrofoil are object of investigation trying to further improve performances as well as to increase the stability and the “sailability". In the following we will present a concept that extends the range of efficiency of the foil through a completely passive morphing of the wing.

Corporate governance is widely suggested by economists and regulators as a solution to reduce agency problems and improve firm performance. However previous studies have failed to generate consistent results. Using a dynamic panel system GMM estimator to alleviate endogeneity concerns we determine the effect of corporate board structure on the performance of a panel of 1265 Chinese firms listed on the Shanghai and Shenzhen stock exchanges from 2010 to 2016. We compare the dynamic system GMM estimator to some commonly used estimators; ordinary least squares (OLS), fixed effects (FE) and the dynamic OLS, and show that these estimates are biased due to endogeneity. The dynamic system GMM estimator incorporates the dynamic nature of internal governance choices to provide valid and powerful instruments that address unobserved heterogeneity and simultaneity. Our results show support for the board model corporate governance mechanism. We find that board size is positive and significantly related to both return on assets and total net profit margin. In addition board independence is positive and significantly related to return on assets but insignificantly related to total net profit margin. Duality was found to have a negative but statistically insignificant relation with firm performance.

The article presents a methodology for modeling the impact of factors of both on-farm activity and environmental factors on the resulting indicators of an international company. The dataset includes the company's profit, revenue, valuation, share price, and market share from 2012 through 2022. This empirical period is optimal for such a type of modeling. Modeling the impact of carbon emissions factors on the resulting indicators is considered based on complex systems theory. Endogenous model variables include indicators of the development of the international company. Predefined model variables reflect the influence of both the external environment and internal factors on the development indicators of an international company. An approach of picture fuzzy rough sets based on time series of endogenous and exogenous variables can provide an opportunity to analyze and consider the consequences of feedback changes in the systems of which they are a part. Based on the results of the analysis of the model construction, it is concluded that picture fuzzy rough sets can be an excellent way to model interdependent social processes.

Non-genuine medical products, including diagnostic devices, have become a lucrative business for fraudsters, causing significant damage to revenues and reputation of companies, as well as posing a significant risk to the health of people and societies. Along a “digital twin” representing centrifugal microfluidic flow control on exemplary “Lab-on-a-Disc” (LoaD) systems, a novel, two-pronged strategy to safeguard miniaturized point-of-care devices by means of secret features and manufacturing challenges is outlined; such “hardware encryption” is flexibly programmed for each chip during production, and deciphered from a secure, local or online database at the time of use. This way, unlicensed copying may be efficiently deterred by an unfavourable economy-of-scale, even in absence of legal prosecution.

The aim of this study is to provide a detailed strategy for Safe-by-Design (SbD) 3D printed lab-on-a-chip (LOC) device manufacturing, using Fused Filament Fabrication (FFF) technology. At first, the applicability of FFF in lab-on-a-chip device development is briefly discussed. Subsequently, a methodology to categorize, identify and implement SbD measures for FFF is suggested. Furthermore, the most crucial health risks involved in FFF processes are examined, placing the focus on the examination of ultrafine particle (UFP) and Volatile Organic Compound (VOC) emission hazards. Thus, a SbD scheme for lab-on-a-chip manufacturing is provided, while also taking into account process optimization for obtaining satisfactory printed LOC quality. This work can serve as a guideline for the effective application of FFF technology for lab-on-a-chip manufacturing through the safest applicable way, towards a continuous effort to support sustainable development of lab-on-a-chip devices through cost-effective means.

This paper examines the relationship between the ratio of independent board member to the financial performance of the company under the mediation of the three pillars of environment, society, and governance (ESG) in Taiwan. The study addresses a research gap between independent directors and corporate financial performance, an issue that is rarely discussed today. The author develops the hypotheses and tests them by applying panel data regression to the data tables taken from the Thomson Reuters Eikon database to analyze data on 173 Taiwanese companies that reported ESG from 2009 to 2021. The results show that the relationship between the ratio of independent directors and financial performance has a positive relationship. At the same time, the 3 pillars of ESG also clearly show the intermediary role in this relationship. Finally, this study provides additional insights into the relationship between the ratio of independent directors and financial performance in the Taiwan context.

Stand Up Paddleboard (SUP) surfing entails riding breaking waves and maneuvering the board on the wave face in a similar manner to traditional surfing. Despite some scientific investigations on SUP, little is known about SUP surfing. The aim of this study was to investigate the physiological response during SUP surfing sessions and to determine how various environmental conditions can influence this response. Heart rate (HR) of an experienced male SUP surfer aged 43 was recorded for 14.9 hours during ten surfing session and synced with on board video footage to enable the examination of the effect of different surfing modes and weather conditions on exercise intensity. Results indicated the SUP surfer's HR was above 70% of HR_max during 85% of each session, with the greatest heart rates were found during falls off the board (~85%HR_max) and while paddling back to the peak (~83%HR_max). Total time surfing a wave was less than 5% with the majority of time spend paddling back into position. Wind speed positively correlated with HR (r² = 0.062, p = 0.012) and wave height negatively correlated wave caching frequency (r² = 0.54, p = 0.025). The results highlight the aerobic fitness for SUP surfing, that wave riding, paddling back to the peak and falls appear to be associated with the greatest cardiovascular demand and that environmental conditions can have an effect of physiological response during SUP surfing sessions.

Cutaneous wound healing is a complex multi-stage process involving direct and indirect cell communication events with the aim of efficiently restoring the barrier function of the skin. One key aspect in cutaneous wound healing is associated with cell movement and migration into the physically, chemically and biologically injured area resulting in wound closure. Understanding the conditions under which cell migration is impaired and elucidating the cellular and molecular mechanisms that improve healing dynamics is therefore crucial in devising novel therapeutic strategies to elevate patient suffering, reduce scaring and eliminate chronic wounds. Following the global trend towards automation, miniaturization and integration of cell-based assays into microphysiological systems, conventional wound healing assays such as the scratch assay or cell exclusion assay have recently been translated and improved using microfluidics and lab-on-a-chip technologies. These miniaturized cell analysis systems allow precise spatial and temporal control over a range of dynamic microenvironmental factors including shear stress, biochemical and oxygen gradients to create more reliable in vitro models that resemble the in vivo microenvironment of a wound more closely on a molecular, cellular, and tissue level. The current review provides (a) an overview on the main molecular and cellular processes that take place during wound healing, (b) a brief introduction into conventional in vitro wound healing assays, and (c) a perspective on future cutaneous and vascular wound healing research using microfluidic technology.

The oil and gas industry faces increasing pressure to remove people from dangerous offshore environments. Robots present a cost-effective and safe method for inspection, repair and maintenance of topside and marine offshore infrastructure. In this work, we introduce a new immobile multi-sensing robot, the Limpet, which is designed to be low-cost and highly manufacturable, and thus can be deployed in huge collectives for monitoring offshore platforms. The Limpet can be considered an instrument, where in abstract terms, an instrument is a device that transforms a physical variable of interest (measurand) into a form that is suitable for recording (measurement). The Limpet is designed to be part of the ORCA (Offshore Robotics for Certification of Assets) Hub System, which consists of the offshore assets and all the robots (UAVs, drones, mobile legged robots etc.) interacting with them. The Limpet comprises the sensing aspect of the ORCA Hub System. We integrated the Limpet with Robot Operating System (ROS), which allows it to interact with other robots in the ORCA Hub System. In this work, we demonstrate how the Limpet can be used to achieve real-time condition monitoring for offshore structures, by combining remote sensing with signal processing techniques. We show an example of this approach for monitoring offshore wind turbines. We demonstrate the use of four different communication systems (WiFi, serial, LoRa and optical communication) for the condition monitoring process. By processing the sensor data on-board, we reduce the information density of our transmissions, which allows us to substitute short-range high-bandwidth communication systems with low-bandwidth long-range communication systems. We train our classifier offline and transfer its parameters to the Limpet for online classification, where it makes an autonomous decision based on the condition of the monitored structure.

Current, application-driven trends towards larger-scale integration (LSI) of microfluidic systems for comprehensive assay automation and multiplexing pose significant technological and economical challenges to developers. By virtue of their intrinsic capability for powerful sample preparation, centrifugal systems have attracted significant interest in academia and business since the early 1990s. This review models common, rotationally controlled valving schemes at the heart of such “Lab-on-a-Disc” (LoaD) platforms to predict critical spin rates and reliability of flow control mainly based on geometries, location and liquid volumes to be processed, and their experimental tolerances. In absence of larger-scale manufacturing facilities during product development, the method presented here facilitates the provision of efficient simulation tools for virtual prototyping and characterization to greatly expedite design optimization according to key performance metrics. This virtual in silico approach thus significantly accelerates, de-risks and lowers costs along the critical advancement from idea, fluidic testing, bioanalytical validation and scale-up to commercial mass manufacture.

The present study finds the association of board characteristics (such as gender diversity, independence, female chairperson or/and female CEO, and board size) and the quality of Corporate Social Responsibility (CSR) disclosure of the top 100 Pakistan Stock Exchange (PSX) listed companies. Unlike most earlier studies in similar contexts, we have focused on CSR disclosure ‘quality’ and not ‘quantity’. We conducted the content analysis of secondary Corporate Governance (CG) and CSR data extracted from the annual reports of PSX-listed companies across ten industrial sectors from period of 2017 and 2018. Our empirical investigation through univariate and multiple regression analysis with Ordinary least squares (OLS) techniques revealed that all the board characteristics potentially have a significant association in lessening CSR disclosure quality. We acknowledge several research limitations, including the study time period and selected board characteristics. While our study has provided some understanding of the association of board characteristics with CSR disclosure quality of PSX-listed companies, several research gaps still need to be addressed. Future investigators should examine this association through the pre-COVID-19 and post-COVID-19 connections and the inclusion of a systems theory perspective.

Enhancing the degree of functional multiplexing while assuring operational reliability and manufacturability at competitive costs are crucial ingredients for enabling comprehensive sample-to-answer automation, e.g., for use in common, decentralized “Point-of-Care” or “Point-of-Use” scenarios. This paper demonstrates a model-based ‘digital twin’ approach which efficiently supports the algorithmic design optimization of exemplary centrifugo-pneumatic (CP) dissolvable-film (DF) siphon valves towards larger-scale integration (LSI) of well-established “Lab-on-a-Disc” (LoaD) systems. Obviously, the spatial footprint of the valves and their upstream laboratory unit operations (LUOs) have to fit, at a given radial position prescribed by its occurrence in the assay protocol, into the locally accessible disc space. At the same time, the retention rate of a rotationally actuated CP-DF siphon valve and, most challenging, its band width related to unavoidable tolerances of experimental input parameters, need to slot into a defined interval of the practically allowed frequency envelope. To accomplish particular design goals, a set of parametrized metrics is defined, which are to be met within their practical boundaries while (numerically) minimizing the band width in the frequency domain. While each LSI scenario needs to be addressed individually on the basis of the digital twin, a suite of qualitative design rules and instructive showcases structures are presented.

We report a small footprint cost-effective isothermal rapid DNA amplification system, with integrated microfluidics for automated sample analysis and detection of SARS-CoV-2 in human and environmental samples. Our system measures low-level fluorescent signal in real-time during amplification, while maintaining the desired assay temperature, on a low power, portable system footprint. A unique soft microfluidic chip design was implemented to mitigate thermocapillary effects and facilitate optical alignment for automated image capture and signal analysis. The system-on-board prototype coupled with the LAMP primers designed by BioCoS, is sensitive enough to detect viral loads of SARS-CoV-2 in a broad concentration range corresponding to a threshold cycle range of 16 to 39. Clinical specimens were tested at Kingston Health Sciences using a clinically validated PCR assay and variants were determined using whole genome sequencing.

Context: Endobronchial tumors are relatively rare. Pathological types are varied, both benign and malignant. Establishing the diagnosis and sleeve resection criteria for such tumors remains a challenge for pulmonologists, bronchoscopists, radiologists, thoracic surgeons, and pathologists. The management of the preoperative assessment of these patients and the establishment of the indication for sleeve resection, represent a big problem. Lung parenchymal sparing surgery remains a challenge, especially in neoplastic patients. Material and methods: We carried out a monocentric retrospective study, during the period 2009-2017, on a number of 57 patients. In our center they benefited from clinical examination, radiography, tomography, respiratory function evaluations, autofluorescence bronchoscopy, cardiological evaluation and detection of blood tumor markers. All the patients benefited from the analysis of the tumorboard of our institute and the establishment of the surgical indication for scleev resection. Results: Sparing of the lung parenchyma was achieved in case of the 57 patients included in the study. The complex evaluations of laboratory parameters, functional tests, CT examination, bronchoscopy, cardiology, were analyzed by the tumor board, so that the indication for surgical intervention was sleeve resection with preservation of the lung parenchyma. Conclusions: We selected patients for sleeve resection, those who presented endobronchial tumors of 2 cm in diameter, with cartilages and bronchial mucosa intact at least 1 cm or 2 cartilages from the formation, on CT and bronchoscopic examination. Cardiological examination and functional tests showed values that do not contradict surgical intervention.

Using lightweight fire-rated board (LFRB) presents cost-effective opportunities for various passive fire protection measures. The aim of the project is to develop a LFRB with enhanced fire resistance, acoustic properties, and mechanical properties. These properties were determined using the Bunsen burner, furnace, energy dispersive X-Ray, impedance tube instrument, and Instron universal testing machine. To fabricate the LFRBs, vermiculite and perlite were blended with flame-retardant bind-ers, and four types of LFRBs were produced. A fire test was conducted to compare the fire-resistance performance of the LFRBs with a commercially available flame retardant board. The B2 prototype showed exceptional fire-resistant properties, with a temperature reduction of up to 73.0 °C as compared to the commercially available fire-rated magnesium board. Incorporating nano chicken eggshell into the specially formulated flame-retardant binder preserved the LFRBs’ structural integrity, enabling them to withstand fire for up to 120 minutes with an equilibrium temperature of 92.6 °C. This approach also provided an absorption coefficient of α = 2.0, a high flexural strength of 3.54 MPa, and effective flame retardancy properties with a low oxygen/carbon ratio of 2.60. These results make the LFRBs valuable for passive fire protection applications in the construction and building materials industry.

Existing research lacks studies that explore the impact of government fiscal support on the high-quality development of regional economy and society from the perspective of livelihood-based infrastructure construction. The investigation in this paper explores the economic and social effects of government fiscal support behavior from the perspective of livelihood infrastructure construction. On the basis of the TOPSIS-Entropy Method, this paper constructs an evaluation indicator that closely conforms to the denotation and requirements of high-quality development and then carries out empirical regressions in combination with government expenditure on people's livelihood to verify the theoretical hypothesis, whose transmission mechanism and moderating effect are further empirically tested. The results reveal that increasing government expenditure on people's livelihoods can effectively improve regional high-quality development, but the marginal improvement degree varies with different periods and locations. The mechanism test proves that the regional consumption level plays a significant part in the mediating effect, accounting for 24.27% of the total effect. Urbanization is also the critical impetus for regional high-quality development and positively moderates the promotion effect of people's livelihood fiscal expenditure. Our study presents a theoretical basis and policy inspiration for improving residents' quality of life and welfare level and improving people's livelihood in the midst of high-quality economic development.

In the dynamic landscape of sustainable computing, use of edge devices is paramount for reducing the need for large-scale centralized data centers. By processing data locally, edge devices minimize the energy-intensive computing in data centers, improving the overall performance, cost-effectiveness whereas reducing the environmental impact. Edge devices may constitute edge clusters composed of resource frugal Single Board Computers (SBC) such as Raspberry Pi etc. The small form-factor and energy efficiency of these computers makes them ideal for processing large data on the edge. Despite their potential, traditional Hadoop configurations struggle to optimize performance in heterogeneous SBC clusters due to disparities in computing resources. Consequently, we propose modifications to the Yet Another Resource Negotiator (YARN) scheduling mechanism to address these challenges. Our proposed changes include the introduction of a Frugality Index and an adaptiveConfig policy. The Frugality Index categorizes SBC nodes based on their capabilities, enabling intelligent resource allocation. The adaptiveConfig policy dynamically adjusts resource allocation in response to workload and cluster conditions, enhancing system efficiency. Additionally, we introduce a fetch_threshold for reduce tasks to improve task prioritization based on locality and data processing efficiency. We evaluate our approach using a 13-node SBC cluster and conduct experiments with CPU-intensive and IO-intensive Hadoop benchmarks. The results demonstrate significant performance improvements compared to native YARN settings, with execution times 4.7 times faster than the worst_native and 1.9 times faster than the best_native scenarios. Furthermore, the proposed adaptiveConfig policy implementing the frugality index and a fetch_threshold outperforms the native YARN by 5.86 times and 1.79 times in Terasort and wordcount executions respectively. Our findings underscore the effectiveness of our approach in managing the heterogeneous nature of SBC clusters and optimizing performance across various hardware configurations. The adaptive policies prove well-suited to the frugal SBC-cluster context, yielding enhanced outcomes and paving the way for sustainable big data processing initiatives.

The increase in the number of firms manipulating financial reports has misled shareholders' investment decisions and resulted in an indelible blot on foreign investors’ trust. Due to earnings management (EM) practice, managers' inefficiency, and lack of transparency in Iraq companies. This study tested the influence of the corporate governance mechanisms (CG), (board independence, audit committee, meeting frequency) on EM based on agency theory, as well, to link between EM and firm's performance (FP) in Iraqi listed companies and the impact of moderating role of corporate social responsibility (CSR) based on the Stakeholder Theory. The study's sample consists of 65 companies for the 2013-2018 financial years. Data were collected mainly from the annual reports (secondary data) of the Iraqi listed firms. This study uses the M-score model to detect EM practices as practical techniques in detecting earnings manipulation practices. The panel static model estimators. Hence, this paper adds to the CG literature from the perspective of stakeholder theory using Iraq's unique industrial environment. Based on the research results, policy-makers might use the study‘s findings to recognize the essential roles of several CG mechanisms in alleviating the opportunistic practices in Iraq. Further, companies should also be encouraged to enhance the CSR disclosure quality.

Hip replacement has significantly improved the quality of life of patients with symptomatic hip osteoarthritis. Metal-on-metal (MoM) bearings have been used with conventional total hip re-placement (THR) for several decades with promising results from early applications. Wear and corrosion of these implants may lead to a release of metal products into surrounding tissue and body fluids. From the 1980s onwards, the search for increasingly better coupling materials with low levels of wear led to the rise of hard-on-hard couplings such as ceramic-on-ceramic (CoC). The latter is currently the coupling with the longest known duration and with a wear rate close to zero. MoM coupling has been for a long time the most significative alternative, but systemic and local complications linked to the release of chromium and cobalt ions, determine the withdrawn from the market. One other alternative proposed over the time has been Ceramic-on-Metal (CoM) bearing. Preliminary results have been described as favourable, but due to the failures of metal on metal it has been withdrawn from the market, without causing significant clinical complications. In this narrative review, we analysed risks and benefits associated with the implantation of hybrid hard-on-hard bearings, such as CoM.

As smoke toxicity is unregulated outside of the mass transport industry, there is no set methodology for assessing smoke toxicity of construction products, like OSB, on a large-scale. This research aims to assess the novel design of a modified ISO 9705 room corner test designed for smoke toxicity quantification. Three tests conditions will be assessed to determine if restriction of ventilation is enough to force a fire to transition to under-ventilated flaming, or if the fuel loading is much more important in affecting the fire severity and fire condition. The research found that fuel loading and test geometry has more significant impact on the fire condition than restricting the ventilation. While imposing restrictions on the test rooms ventilation did increase the equivalence ratio, it was not sufficient enough to force the transition into under-ventilated flaming. The addition of a door to the test room did not force the fire to transition to under-ventilated flaming. When doubling the fuel loading, there was sufficient fuel for the fire to transition to under-ventilated flaming. This research has provided the experimental methodologies to assess smoke toxicity at a range of ventilation conditions on a large-scale.

Artificial intelligence is increasingly used in various branches of engineering. In this article, artificial neural networks are used to predict the crush resistance of corrugated packaging. Among the analysed packages were boxes with ventilation openings, packages with perforations, and typical flap boxes, which makes the proposed estimation method very universal. Typical shallow feedforward networks were used, which are perfect for regression problems, mainly when the set of input and output parameters is small, so no complicated architecture or advanced learning techniques are required. The input parameters of the neural networks are selected so as to take into account not only the material used for the production of the packaging, but also the dimensions of the box and the impact of ventilation holes and perforations on the load capacity of individual walls of the packaging. In order to maximize the effectiveness of neural network training process, the group of input parameters was changed so as to eliminate those to which the sensitivity of the model was the lowest. This allowed the selection of the optimal configuration of training pairs for which the estimation error was on the acceptable level. Finally, models of neural networks were selected, for which the training and testing error did not exceed 10%. The demonstrated effectiveness allows to conclude that the proposed set of universal input parameters is suitable for efficient training of a single neural network model capable of predicting the compressive strength of various types of corrugated packaging.

Paper is a material whose mechanical properties are highly dependent on humidity and temperature. Which naturally also builds the relationship between the stiffness and strength of corrugated board and changing weather conditions. In this paper, attention is focused on the dependence of the physical properties of the cardboard on changes in humidity and temperature, which undergo dynamic fluctuations both during the production of corrugated board and during its storage. Two techniques were used to test this effect, namely numerical homogenization and global sensitivity analysis. Both methods were implemented to determine the theoretical relationships between the change in humidity and/or temperature in each layer of corrugated board and its global bending, compression and shear stiffness. The procedure was used to analyze different types of 5-ply and 3-ply cardboard. The obtained results allowed to build a complete map of the relationship between the change in humidity of selected layers and the strength characteristics of the full assembly.

The corrugated board is a versatile and durable material that is widely used in the packaging industry. Its unique structure provides strength and cushioning, while its recyclability and bio-degradability make it an environmentally friendly option. The strength of corrugated board depends on many factors, including the type of individual papers on flat and corrugated layers, the geometry of the flute, temperature, humidity, etc. This paper presents a new approach to analysis geometric features of corrugated boards based on the images. It allows for precise determination of the geometry of the corrugated layer, as well as the thickness of individual papers in all cardboard layers. The experimental set used in the work and the created software are characterized by high reliability and precision of measurement thanks to the use of an identification procedure based on image analysis and evolutionary algorithms. This allows to quickly find the main geometric characteristics of the corrugated board, which in turn leads to the possibility of performing numerical analyzes taking into account the real model of the corrugated board. Calculations made on a real (correctly mapped geometrically) model allow, for example, a more reliable analysis of the composition of the cardboard, and thus also to obtain greater savings in the optimization process.

The objectives of the research are to investigate the characteristics of the board of directors on the financial performance of the enterprise. Using a sample data from 52 construction and real estate enterprises listed on Vietnam stock exchange in the period 2006-2020. Using typical regression methods such as pooled OLS, FEM, REM and assessing the defects of the research model, the FGLS method is selected. At the same time, due to the existence of endogenous phenomena and the nature of interdependence among enterprises in Vietnam, research using the instrumental variables two-step generalized method of moments (IV-GMM) in order to correct for cross-sectional dependence, autocorrelation, endogeneity, and heteroskedasticity in the analysis. Research results suggest that board size, female board members, meeting frequency, and board members' education have a positive influence on financial performance. Moreover, the independence of the Board of Directors increases, the business efficiency decreases. The research also found a positive relationship of tangible fixed assets, and a negative relationship between capital structure choice, firm size and corporate financial performance.

In the modern world, all manufacturers strive for the optimal design of their products. This general trend is recently also observed in the corrugated board packaging industry. Colorful prints on displays, perforations in shelf-ready-packaging and various types of ventilation holes in trays, although extremely important for ergonomic or functional reasons, weaken the strength of the box. To meet the requirements of customers and recipients, packaging manufacturers outdo each other in new ideas for the construction of their products. Often the aesthetic qualities of the product become more important than the attention to maintaining the standards of the load capacity of the packaging (which, apart from their attention-grabbing functions, are also intended to protect transported products). The particular flaps design (both top and bottom) and their influence on the strength of the box is investigated in this study. The updated analytical-numerical approach is used here to predict the strength of the packaging with various flap’s offsets. Experimental results indicated a significant decrease in the static load-bearing capacity of packaging in the case of shifted flap creases. The simulation model proposed in our previous work has been modified and updated to take into account also this effect. The results obtained by the model presented in the paper are in satisfactory agreement with the experimental data.

Alzheimer’s disease (AD) is a significant health concern worldwide with enormous social and economic impact globally. The gradual deterioration of cognitive functions and irreversible neuronal losses are primary features of the disease. Even after decades of research, most therapeutic options are merely symptomatic, and drugs in clinical practice present numerous side effects. Lack of effective diagnostic techniques prevents the early prognosis of disease, resulting in a gradual deterioration in the quality of life. Furthermore, the mechanism of cognitive impairment and AD pathophysiology is poorly understood. Microfluidics exploits different microscale properties of fluids to mimic environments on microfluidic chip-like devices. These miniature multichambered devices can be used to grow cells and 3D tissues in vitro, analyze cell-to-cell communication, decipher the roles of neural cells like microglia, and gain insights into AD pathophysiology. This review focuses on the applications and impact of microfluidics on AD research. We discuss the technical challenges and possible solutions provided by this new cutting-edge technique to understand disease-associated pathways and mechanisms.

Corrugated board, widely used in the packing industry, is a recyclable and durable material. Its strength and cushioning, influenced by geometry, environmental conditions like humidity and temperature, and paper quality, make it versatile. Double-walled (or five-ply) corrugated board, comprising two flutes and three liners, enhances these properties. This study introduces a novel approach to analyze 5-layered corrugated board, extending a previously published algorithm for single-walled boards. Our method focuses on measuring layer and overall board thickness, flute height, and center lines of each layer. Integrating image processing and genetic algorithms, the research successfully developed an algorithm for precise geometric feature identification of double-walled boards. Images were recorded using a special device with a sophisticated camera and image sensor for detailed corrugated board cross-sections. Demonstrating high accuracy, the method faced limitations only with very deformed or damaged samples. This research contributes significantly to quality control in the packaging industry and paves the way for further automated material analysis using advanced machine learning and image sensors. It emphasizes the importance of sample quality and suggests areas for algorithm refinement to enhance robustness and accuracy.

Abstract: For the problem of small target of printed circuit board surface defects and low detection accuracy, the printed circuit board surface defect detection network DCR-YOLO is designed to meet the premise of real-time detection speed and effectively improve the detection accuracy. Firstly, the backbone feature extraction network DCR-backbone, consisting of two CR residual blocks and one common residual block, is used for small target defect extraction on printed circuit boards. Secondly, the SDDT-FPN feature fusion module is responsible for the fusion of high level features to low level features, while enhancing feature fusion for the feature fusion layer where the small target prediction head YOLO Head-P3 is located to further enhance the low level feature representation. the PCR module enhances the feature fusion mechanism between the backbone feature extraction network and the SDDT-FPN feature fusion module at different scales of feature layers. the C5ECA module is responsible for adaptive adjustment of feature weights and adaptive attention to the requirements of small target defect information, further enhancing the adaptive feature extraction capability of the feature fusion module. Finally, three YOLO-Heads are responsible for predicting small target defects for different scales. Experiments show that the DCR-YOLO network model detection Map reaches 98.58%, the model size is 7.73MB, which meets the lightweight requirement, and the detection speed reaches 103.15fps, which meets the application requirements for real-time detection of small target defects.

The COVID-19 pandemic had a wide-ranging impact, resulting in a global recession due to weakened purchasing power. This circumstance necessitates business organizations adapting to developments and being more conscious of the risk of financial statement fraud. The intention of this research is to investigate the way corporate governance affected financial statement fraud during the COVID-19 pandemic. To acquire empirical data for examining corporate governance variables on financial statement fraud, the research was examined using quantitative methods. The study takes advantage of secondary data acquired from annual reports of companies under special monitoring listed on the Indonesia Stock Exchange of 2020-2021. The logistic regression method was used to evaluate 134 data sets, and financial statement fraud was measured using the Z-Score and F-Score models. The results indicate that using the Z-score, only the board size has a negative effect on financial statement fraud during the COVID- 19 pandemic. Meanwhile, using the F-Score, the corporate governance variables studied are not proven to have an influence on financial statement fraud during the COVID 19 pandemic.

A lightweight image encryption algorithm based on chaos induction via a 5-dimensional hyperjerk oscillator (5DHO) is presented. First, the dynamics of our 5DHO network is investigated and shown to exhibit up to five coexisting hidden attractors in the state space that depend exclusively on the system’s initial values. Further, a simple implementation of the circuit was used to validate its ability to exhibit chaotic dynamical properties. Second, an Arduino UNO platform is used to confirm the usability of our oscillator in digital implementation of the system. Finally, an efficient image encryption application is executed using the proposed chaotic networks based on the use of permutation-substitution sequences. The superior qualities of the proposed strategy are traced to the dynamic set of keys used in the substitution process which heralds the generation of the final ciphered image. Based on the results obtained from the entropy analysis (7.9976), NPCR values (99.62), UACI tests (33.69) and encryption execution time for 512x512 images (0.1179 sec), the proposed algorithm is adjudged to be fast and robust to differential and statistical attacks relative to similar approaches.

Background: Exclusively breastfeeding your newborn while in the hospital is imperative for suc-cessful breastfeeding at home. This study will investigate if having a nurse on-site during rooming-in can enhance the proportion of exclusive breastfeeding. Methods: We carried out a prospective cohort study to assess exclusive breastfeeding in the first three months of life among two Neona-tology Units in Southern Italy with different hospital settings. The Ente Ecclesiastico Miulli of Ac-quaviva delle Fonti had on-site nurses available 24/7 (on-site group), while the Policlinico of Bari had nurses available on call 24/7 from the Neonatology Unit (on-call group). Results: Between January 3rd and March 31st, 2018, a total of 564 sets of mothers and babies were admitted - 299 on-site and 265 on-call. The exclusive breastfeeding rate for the entire group was 76.4% at 90 days, demonstrating the positive impact of rooming-in and nursing, regardless of the setting. Infants delivered via ce-sarean section in the on-site group demonstrated higher rates of exclusive breastfeeding at both 30 and 90 days of life. Conclusions: Our research indicates that having a nurse available at all times is crucial for promptly identifying any problems with breastfeeding. We highly suggest having an on-site nurse present during rooming-in for mothers who have had a caesarean delivery. This nurse should continuously promote exclusive breastfeeding until the baby is three months old.

Microfluidic lab-on-chip devices are widely being developed for chemical and biological studies. One of the most commonly used types of these chips is perfusion microwells for culturing multicellular spheroids. The main challenge in such systems is the formation of substantial necrotic and hypoxic zones within the cultured spheroids. Herein, we propose a novel acoustofluidic integrated platform to tackle this bottleneck problem. We show that such an approach enhances cell viability and shrinks necrotic and hypoxic zones in these spheroid-on-a-chip platforms without the need to increase the flow rate, leading to a significant reduction in costly reagents' consumption. Proof-of-concept, designing procedures, and finite element numerical simulation are discussed in details. Also, the effects of acoustic and hydrodynamic parameters on the cultured cells are investigated. The results show that by increasing acoustic boundary displacement amplitude (d0), the spheroid’s proliferating zone enlarges greatly. Moreover, it is shown that by implementing d0=0.5 nm, the required flow rate to maintain the necrotic zone below 13% will be decreased 12 times compared to non-acoustic chips.

Pin-on-plate and pin-on-disk wear tests are typically used for assessing the wear behavior of a given material coupling. Such a behavior is frequently described by a wear coefficient k, which is estimated, according to the Archard’s law, as the ratio between the measured wear volume V and the product of the applied normal force F and the sliding distance s, i.e. k=V/(F s). This study demonstrates that such a relationship is correct for pin-on-plate but not for pin-on-disk, particularly for flat-ended pins. Both analytical and finite element models of the two tests were developed, considering three different distances pin-disk axis. As results, wear volumes, pressure and wear depth maps were examined and compared for the same sliding distance. Though this study is focused only on the initial transient part of the wear tests, some interesting aspects arose: i) rotational effect in pin-on-disk tests affects k estimation, especially when the pin is near to the disk axis; ii) a simple analytical function is defined to correct the wear volume estimation for pin-on-disk tests; iii) due to the different sliding distances of contact points in pin-on-disk tests, pressure redistribution occurs with higher values on the inner side (closer to disk axis); the opposite trend is observed in wear depth maps. From a computational point of view, the pin-on-disk problem, only apparently simple, required very small time increments to correctly describe the circular trajectories of points, with high computational costs. Numerical strategies are currently under investigation to extend the study to the steady state phase of both tests.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Abstract: The aim of this study was to compare the influence of corporate board characteristics on the extent of environmental disclosure quantity of listed firms in two leading emerging economies in Africa, South Africa (integrated reporting framework) and Nigeria (traditional reporting framework). Methods: The sample was comprised of 303 firms including environmentally sensitive companies purposively selected for content analysis study in South Africa (213) and Nigeria (90). We used both descriptive, multivariate and regression models to comparatively analyze the differences about corporate board characteristics as determinants of the extent of their environmental disclosure quantity. Results: The results reveal a more significant positive association between board characteristics and environmental disclosure in South Africa and less relevant association in Nigeria. Also, the results support that board independence arrangement may serve as bonding mechanisms in weak reporting environments, suggesting a substitutive relationship between board independence and the regulatory framework. Quiet revealing a board with environmental committee show a higher tendency to be ecologic transparent in both countries. However, in a traditional reporting framework, the environmental committee is not enough; its effect was insignificant and highly significant in the integrated reporting framework. Further revealed is the significant positive effect of industry membership influence on environmental disclosure. In all estimated models of South Africa sample show that 45% of environmentally sensitive industries significantly influence environmental disclosure, while 51% is environmentally polluting industries in Nigeria show less concern on environmental disclosure. Interestingly, Audit firm size (Big4) positively and statistically significantly associated with overall environmental reporting in both countries. The results are consistent with stakeholder theory, agency theory, institutional and legitimacy theory suggesting that a strong board size, independent members of the board with auditing experience, the active environmental committee in conjunction with solid audit reputation may reduce information asymmetry. Our findings will be helpful for policymakers and other regulators who are interested in environmental impact reporting.

Digital microfluidics (DMF) holds great potential for the alleviation of laboratory procedures in assisted reproductive technologies (ARTs). Electrowetting on dielectric (EWOD) provides dynamic culture conditions in vitro that may better mimic the natural embryo microenvironment. Thus far, EWOD microdevices have been proposed for in vitro gamete and embryo handling in mice and for analyzing the human embryo secretome. This article presents the development of the first microfluidic chip utilizing EWOD technology designed for the manipulation of bovine embryos in vitro. The prototype sustains the cell cycles of embryos manipulated individually on the chips during in vitro culture (IVC). Challenges related to the chip fabrication as well as to its application during bovine embryo IVC in accordance with the adapted on-chip protocol are thoroughly discussed, and future directions for DMF in ARTs are indicated.

Efficient use of the operating room (OR) is crucial for any hospital. One of the major inefficiencies in the OR is surgical cases not starting or finishing on time as scheduled. When a case is delayed, it affects all subsequent cases in that OR. This study uses discrete choice analysis to determine the significant factors, including team familiarity, that influence OR case on-time start and finish. A case is considered on-time if the documented procedure start and finish times are no more than 10 minutes after the scheduled start and finish times. The analysis uses surgical case data from a large tertiary referral hospital and academic center in Greenville, South Carolina. The case data includes all surgical cases (15,091) performed during regular workdays in 2013. Two binary logit models are developed: one for case on-time start and one for case on-time finish. Results indicate that higher team familiarity between surgeon and anesthesiologist, surgeon and circulating nurse, surgeon and scrub nurse, and surgeon and CRNA improve the likelihood of an OR case on-time start and on-time finish. This finding indicates that the OR scheduling staff in the study hospital make a concerted effort to schedule the surgical teams with members who have worked well together in the past.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

The article presents a simplified method for determining the strength of a corrugated board packaging subjected to dynamic transport loads. The proposed algorithm consists of several calculation steps: (1) a static analysis of the compressive strength of the package, (2) an analysis of random vibrations in the frequency domain, used to determine the resonance frequencies, and (3) a dynamic analysis of the package loaded with computed resonant frequencies. For this purpose, numerical models of the static compression test of the packaging before and after the dynamic analysis of the package subjected to general transport loads were developed. In order to validate the model, the laboratory packaging compression tests were also performed for samples of boxes with 3-layer cardboard. Thanks to this, it was possible to verify the results of numerical simulations of compression tests for several box geometries. Which, in turn, allowed for the development of a method based on dynamic and post-dynamic (static) numerical analysis, allowing to determine with high accuracy the resistance of selected packaging to vibrations and dynamic loads. The results of the (validated experimentally) numerical analysis prove the usefulness of the simplified method presented here for precise estimation of the load capacity of various packages dynamically loaded during transport.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

In this paper we investigate analytic automorphisms of complex topological vector spaces and their applications to linear and nonlinear transitive operators. We constructed some examples of polynomial automorphisms which show that a natural analogue of the Jacobian Conjecture for infinite dimensional spaces is not true. Also, we prove that any separable Fréchet space supports a transitive analytic operator which is not a polynomial. We found some connections of analytic automorphisms and algebraic bases of symmetric polynomials and applications to hypercyclisity of composition operators.

In this paper, a prototype of an automatic lab on PCB for agarose preparation and electrophoresis is developed. The dimensions of the device are 38×34 mm2 and includes a conductivity sensor for detecting the TAE buffer (Tris-Acetate-EDTA buffer), a microheater for mixing, a NTC thermistor for controlling the temperature, a LDR sensor for measuring the transparency of the mixture, and two electrodes for performing the electrophoresis. The agarose preparation functions are governed by a microcontroller. The device requires a PMMA structure to define the wells of the agarose gel, and to release the electrodes from the agarose. The maximum voltage and current that the system requires are 40 V to perform the electrophoresis, and 1 A for activating the microheater. The chosen temperature for mixing is 80ºC, with a mixing time of 10 min. In addition, the curing time is about 30 min. This device is intended to be integrated as a part of a larger lab on PCB system for DNA amplification and detection. However, it can be used to migrate DNA amplified in conventional thermocyclers. Moreover, the device can be modified for preparing larger agarose gels and performing electrophoresis in an automatic manner.

Organ-on-Chip is a game-changing technology born from the convergence of tissue engineering and microfluidic technology. Organ-on-Chip devices (OoCs) are expected to offer effective solutions to persisting problems in drug development and personalized disease treatments. This opinion paper surveys the current landscape in research, development, application and market opportunities for OoCs to help establishing a global and multi-stakeholder OoC ecosystem. Based on a bibliometric study, a market analysis, expert interviews, and panel discussions held at the ORCHID Vision Workshop (Stuttgart, 23 May 2018), we outline presently unmet needs, key challenges, barriers and perspectives of the field, and finally propose recommendations towards the definition of a comprehensive roadmap that could render OoCs realistic models of human (patho)physiology in the near future.

This research paper contributes to the literature of deterrence theory in general, and in particular with respect to white-collar crime, offering valuable inside by using a unique data set of fraud and violation of trust incidents for Paraguay. Descriptive evidence show a clear and continuous misallocation of funds and human capital, and therefore providing less efficient services for the public. Regression analysis suggests that clearance rate exerts a highly significant effect in deterring fraud but results are not clear for violation of trust incidents. Despite the limitations of available data, results confirm deterrence theory in Paraguay. However, to more than two-thirds of victims, not even the attempt was made to seek justice. As a side-result, it seems that a soft on crime strategy, induced from the former German penal code, has led to an increasing share of pre-trial diversion and therefore enhancing white-collar crimes like fraud and violation of trust due to impunity.

Biometric based access control system acts as a weapon against the challenges for reliable authentication mechanism. Although there are many advantages of biometric system, still it is vulnerable to attacks, which decline its security. This leads to propose a new approach to address these open issues and challenges for biometric data security. Smart card have been already used in past with various degree of success to store biometric credentials. Match-on-card biometric framework locks the biometric data inside the microcontroller of the smart card, which leads to minimal risks if card is lost or stolen. It is fast and accurate, balancing security and convenience by never exchanging user data outside the system of smart card and performs fingerprint enrollment as well as matching within a tamperproof environment of smart card.

Corrugated board is a composite material characterized by strong orthotropy in both the elastic and plastic phases. Additionally, due to its layered structure, which consists of alternately arranged flat and wavy layers of paper, its mechanics becomes complicated. Therefore, a precisely selected set of laboratory tests is needed to correctly identify all the necessary material parameters of cardboard. The work attempts to define a full set of laboratory tests in order to determine material parameters describing the linear-elastic, orthotropic behavior of cardboard and the basic parameters defining popular plasticity criteria, such as the asymmetric orthotropic Hoffman criterion. For this purpose, sensitivity analysis and numerical models of several selected basic laboratory tests were used. Since the aim of the work is to choose appropriate laboratory tests necessary to correctly determine the material parameters of corrugated board (not its individual layers), the numerical models do not contain detailed cardboard geometry, but only its homogenized representation in the form of the flat shell models. All numerical models are based on the nonlinear finite element method and constitutive modelling in the form of UMAT subroutines implemented in the ABAQUS software. Based on the analyses, appropriate measurements and laboratory tests were indicated that are most sensitive to the material parameters sought.

In this work, three different types of sandwich structures were manufactured using Formica sheet (a paper-based sheet) as skin and perlite/sodium silicate foam as core with/without the paper honeycomb. The sandwich structures were fabricated by attaching Formica sheets on both sides of the honeycomb, perlite/sodium silicate foam, and perlite/sodium silicate foam-filled honeycomb core panels. The flexural characteristics were studied by a three-point bending test and the thermal conductivity was measured using Lee’s thermal conductivity apparatus. The results demonstrated a significant improvement in flexural properties, including core shear stress, facing stress, bending stress, and energy absorption, when incorporating the paper honeycomb reinforcement. The thermal conductivity and flexural properties were found to be well-compatible with the existing building materials for similar applications in the literature. The failure investigation revealed that the sandwiches with paper honeycomb only prematurely failed due to core buckling, whereas the foam-filled honeycomb core-based sandwiches were able to sustain higher loads, exhibiting material failures such as core shear failure, skin rapture, and delamination. It is found that the foam-filled paper honeycomb sandwich structures can withstand higher bending loads compared to foam core-based and paper honeycomb-based sandwich structures. These developed sandwiches offer potential as green materials due to the characteristics of their constituent materials and can find valuable applications in the building thermal insulation.

Currently Single Board Computers (SBCs) are sufficiently powerful to run Real-Time Operating Systems (RTOSs) and applications with real-time attributes and requirements. SBCs serve as a foundation in Industrial Internet of Things (IIoT). The NXP Semiconductors produces a series of SBCs based on ARM-processors for a variety of industrial applications. The continuous increase in real-time data generated by IoT devices adds further research issues about the efficiency of such systems and applications. The purpose of this research was to investigate the timing performance of an NXP TWR-K70F120M device with μClinux OS on running concurrently tasks with real-time features and constraints. A custom-built multithreaded application with specific compute-intensive sorting and matrix operations was developed and applied to obtain measurements in specific timing metrics, including task’s execution time, threads waiting time, and response time, under different threads variations. The performance of this device was additionally benchmarked and validated against favorite platforms, a Raspberry Pi4 and BeagleBone AI SBCs. The experimental results showed that this device stands well both in terms of timing and efficiency metrics. Execution times were quite lower than the others, by approximately 56% in the case of two threads, and by 29% in the case of thirty-two threads configurations.

Worldwide, among older adults, infection is the leading mortality cause; chronic nutritional deficits confer significant mortality risk and increase healthcare costs. The association of the Global Leadership Initiative on Malnutrition (GLIM)-defined malnutrition with infection-related mortality, especially with renal dysfunction in older patients, remains unevaluated. In older patients hospitalized with infection, stratified by renal function, we investigated the association of malnutrition severity with mortality. This single-center, retrospective cohort study of 1220 participants (age ≥65 years) admitted to Aichi Medical University from 2019 to 2020 used a multivariate Cox proportional hazards model to determine the association of GLIM-defined nutritional status (no, moderate, or severe malnutrition) with all-cause mortality. Compared to no malnutrition, moderate and severe malnutrition conferred significantly higher mortality (adjusted hazard ratio [confidence interval ]: 1.00 [reference], 1.76 [1.28-2.42], and 2.44 [1.78-3.33], respectively), with the highest all-cause mortality in malnutrition with a low estimated glomerular filtration rate (eGFR <30 mL/min/1.73m2; 7.35 [4.57-11.8]) compared to no malnutrition and normal eGFR (≥60 mL/min/1.73m2). GLIM-defined malnutrition confers higher all-cause mortality risk in older adults with infection, especially those with renal dysfunction. This information enables the identification of high-risk older patients with infection and targeted clinical management of those with malnutrition, renal dysfunction, and infection.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

The one pot hydrogenolysis/hydrogenation reaction of maltose to 2 moles of sorbitol has been carried out over different supported Cu catalysts in water at 180°C and 40 bar of H2. Only the catalysts supported on silicas were found to be effective in this reaction giving up to 86% yield in the desired product while the bare supports and the catalysts supported on alumina or silica alumina gave messy reactions. The peculiar activity of the two Cu/Silica systems tested was ascribed to high metal dispersion and suitable polarity of the catalyst surface. The reduced catalyst, exposing metallic Cu particles on the surface, showed unusual stability in the presence of water as a solvent and could be reused several times without any treatment.

Fluorescence-linked immunosorbent assay (FLISA) is a commonly used, quantitative technique for detecting biochemical based on antigen–antibody binding reactions using a well-plate platform. With the developments in the manufacturing technology of microfluidic systems, FLISA can be implemented onto microfluidic disk platforms, which allows the detection of trace biochemical with high resolutions. Apart from requiring a lower proportion of reagent (1/10), this method also reduces the time required for the entire process to less than an hour. The incubation process involves antigen–antibody binding reactions as well as the binding of fluorogenic substrates to target proteins. The protocol for FLISA on a microfluidic platform necessitates the appropriate execution of liquid reagent movements during each step in order to ensure sufficient binding reactions. Herein, we propose a novel microfluidic disk comprising a 3D incubation chamber. Vascular endothelial growth factor as concentration with ng mL-1 is detected sequentially using a benchtop process employing this 3D microfluidic disk. The 3D microfluidic disk is implemented without requiring manual intervention or additional procedures for liquid control. During the incubation process, microbead movement is controlled through centrifugal force, generated due to disk rotation, and gravitational force via bead sedimentation on the sloped floor of the chamber.

This paper aims to describe the geometrical structure and explicit expressions of family of finitely parametrized probability densities over smooth manifold $M$. The geometry of family of probability densities on $M$ are inherited from probability densities on Euclidean spaces $\left\{U_\alpha \right\}$ via bundle morphisms, induced by an orientation-preserving diffeomorphisms $\rho_\alpha:U_\alpha \rightarrow M$. Current literature inherits densities on $M$ from tangent spaces via Riemannian exponential map $\exp: T_x M \rightarrow M$; densities on $M$ are defined locally on region where the exponential map is a diffeomorphism. We generalize this approach with an arbitrary orientation-preserving bundle morphism; we show that the dualistic geometry of family of densities on $U_\alpha$ can be inherited to family of densities on $M$. Furthermore, we provide explicit expressions for parametrized probability densities on $\rho_\alpha(U_\alpha) \subset M$. Finally, using the component densities on $\rho_\alpha(U_\alpha)$, we construct parametrized mixture densities on totally bounded subsets of $M$. We provide a description of inherited mixture product dualistic geometry of the family of mixture densities.

In this work, an evanescent Bragg grating sensor inscribed in a few-mode planar polymer waveguide was integrated in microchannel structures and characterized with various chemical applications. The planar waveguide and the microchannels consisted of epoxide-based polymers. The Bragg grating structure was post-processed using point-by-point direct inscription technology. By monitoring the central wavelength shift of the reflected Bragg signal, the sensor showed a temperature sensitivity of -47.75 pm/K. Moreover, the functionality of the evanescent field-based measurements is demonstrated with two application examples: refractive index sensing of different aqueous solutions and gas-phase hydrogen concentration detection. For the latter application, the sensor was additionally coated with a functional layer based on palladium nanoparticles. During the refractive index sensing measurement, the sensor achieved a sensitivity of 6.5 nm/RIU from air to 99.9% pure isopropyl alcohol. For the gas-phase hydrogen detection, the coated sensor achieved a reproducible concentration detection up to 4 vol% hydrogen. According to the reported experimental results, the integrated Bragg grating-based waveguide sensor demonstrates high potential for applications based on lab-on-a-chip concept.

The gut plays a key role in drug absorption and metabolism of orally ingested drugs. Additionally, characterization of intestinal disease processes are increasingly gaining more attention as gut health is an important contributor to our overall health. The most recent innovation to study intestinal processes in vitro is the development of gut-on-a-chip (GOC) systems. Compared to conventional in vitro models they offer more translational value, and many different GOC models have been presented over the past years. Here, we reflect on the almost unlimited choices in designing and selecting a GOC for preclinical drug (or food) development research. Four components that largely influence the GOC design are highlighted, namely 1) the biological research questions, 2) chip fabrication and materials, 3) tissue engineering, and 4) the environmental and biochemical cues to add or measure in the GOC. Examples are presented of GOC studies in the two major areas of preclinical intestinal research: 1) intestinal absorption and metabolism to study the oral bioavailability of compounds, and 2) treatment-orientated research for intestinal diseases. The last section of this review presents an outlook on the limitations to overcome in order to accelerate preclinical GOC research.

Despite the use of commercial forest carbon protocols (CFCPs) for more than two decades, claiming ~566 MMtCO₂e and a market value of ~USD $15.7 billion, comparative analysis of CFCP methodology and offset results is limited. In this study, five widely used biometric-based CFCPs are characterized, and common characteristics and differences are identified. CFCP claims of net forest carbon sequestration are compared with results of directly measured CO₂ by eddy covariance, a meteorological method integrating gross vertical fluxes of forest and soil carbon, and the only alternative non-biometric source of net forest carbon sequestration data available. We show here that CFCPs share a structural feature delimiting forest carbon values by zero-threshold carbon accounting (gC m^-2 ≤ 0), a pattern opposite to natural emissions of forest CO₂ exchange based on direct measurement and a fundamental biological constraint on net forest carbon storage (i.e., soil efflux, ecosystem respiration). Exclusion of forest CO₂ sources to the atmosphere precludes net carbon accounting, resulting in unavoidable over-crediting of CFCP project offsets. CFCP carbon results are significantly different from global forest CO₂ net ecosystem exchange population results (FluxNet2015 gC m^-2) at the 95% to 99.99% confidence levels, inferring an annual median error of ~247% (gC m^-2), consistent with over-crediting. Direct CO₂ measurement provides an urgently needed alternative method for commercial forest carbon products that has the potential to harmonize global markets and catalyze the role of forests in managing climate change through nature-based solutions.

Separation and interpretation of rebellious Circulating Tumor Cells (CTCs) originating from the primary tumor or cancer tissue plays a significant role in diagnostics, cancer progression analyses, suitable medicine exploration, and treatment proficiency examination. Cancer metastasis occurs when CTCs spread throughout the body and invade healthy tissues, leading to new tumors in that area. Although a dramatic rate of deaths begins from spreading CTCs around the body, valuable measures have been made to control their development. However, the first step is separating these harmful cells from the bloodstream and investigating their features. Having examined the characteristics of CTCs as cancer’s main strength, researchers can introduce complementary treatments that can affect cancerous cells without damaging the healthy cells. Therefore, according to their unique characteristics, numerous techniques have been established for continuous and fast separation and sorting of CTCs. Nevertheless, few separators enjoy the efficient performance and appropriate accuracy and can be produced in mass numbers due to the available fabrication equipment. Microfabrication advancements enable separators to combine the advantages of active and passive methods in a small-scale platform for probing individual cells and separation purposes. Reduction in reagents, sample volume, analysis time, and less harmfulness to patients are some of the motivations that encourage researchers to employ microfluidic instruments for CTCs separation from other blood cells over the last two decades. However, microfabrication limitations mean effective separators, and the diagnostic option they provide, are not readily available. Addressing these limitations requires optimizing the design and fabrication of separators such that they are reduced in their size and fabrication cost, while also maintaining high-throughput separating capability. The emergence of the Lab-On-a-Chip (LOC) and then Lab-On-a-CD (LOCD) technologies, having more inherent benefits than conventional microfluidic devices, has created new opportunities and become increasingly widespread in recent years. Evidence suggests that employing single methodologies or integrating approaches without sufficient understanding of potential outcomes is unlikely to result in successful diagnostic results. This paper contributes an extensive review of several separation systems, including fundamental theories and experimental details, and describes detailed operating principles and device performance.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

This paper sheds light on how crisis management affects post-disaster re-covery. Based on the study of the management of a major environmental disaster, hurricane IRMA, we consider how post-disaster recovery is impacted by crisis management strategies. The perspectives of local stakeholders from the islands of St Martin and St Barthélémy will be shared. We analyze how territories exposed to the same natural phenomena have different outcomes and consider some of the possible reasons. This study reveals underlying risk drivers, to address governance reorganization with a view to better managing socio-economic recovery.

This article presents a wide-band antenna designed for the Cube Satellite (CubeSat). Based on a quadrifilar structure, the antenna provides circular polarization radiation, which is suitable for satellite communication. Moreover, the antenna is designed and fabricated using two 1.6 mm thickness FR4-Epoxy boards that connect together by the metal pins. In order to improve the robustness, a ceramic spacer is placed in the centerboard, and four screws at the corners are added to fix the antenna with the CubeSat structure. These additional parts reduce antenna damage caused by vibrations in the launch vehicle lift-off stage. The proposal has a dimension of 77mm x 77mm x 10mm and covers the LoRa frequency bands of 868 MHz, 915 MHz, and 923 MHz. According to the measurements in an anechoic chamber, antenna gains are obtained with the values of 2.3 dBiC and 1.1 dBiC for the 870 MHz and 920 MHz, respectively. Finally, the antenna is integrated into a 3U CubeSat that was launched by a Soyuz launch vehicle. The terrestrial-to-space communication link was measured, and the antenna performance was confirmed in the real-life scenario.

This paper introduces a novel 3D NoC router that combines buffered and bufferless routing with approximate priority comparison when deflecting flits. Our proposal is a modification of an asymmetrical router that is buffered in the z dimension ports and bufferless in the x and y dimension ports. Flits that request output ports in the x and y dimensions are granted or deflected based on approximate, instead of accurate, priority comparison. Experimental results show that the proposed router, besides effectively combining the advantages of both buffered and bufferless routers, it achieves additional performance and area gains due to the reduced logic required for approximate priority comparison in flit deflections. Experimental results using synthetic and realistic traffic show that the proposed router begins to saturate at a sifnificantly higher injection rate than a bufferless router, but at a slightly lower injection rate than when using accurate priority comparison. Furthermore, the proposed router achieves higher clock frequencies and reduced area compared to the simpler permutation network.

The purpose of this work is to define optimal growth conditions for batch culture of the cyanobacterium Arthrospira maxima and the microalgae Chlorella vulgaris, Isochrysis galbana and Nannochloropsis gaditana. Thus, we study the effect of three variables on algae growth: i.e., inoculum:culture medium ratio, light:darkness photoperiod and type of culture medium, including both synthetic media and wastewaters. The results showed that the initial inoculum volume did not affect the amount of biomass at the end of the growth (14 days), whereas an excess (18 h) or defect (6 h) in the number of hours of light is determinant for its development. The contribution of nutrients from different culture media modified the growth of the different species. A. maxima was favoured in seawater enriched with Guillard's F/2 as well as C. vulgaris and N. gaditana but in fresh water medium. I. galbana had the greatest growth in the marine environment enriched with Walne’s media. Nitrate was the limiting growth reagent at the end of the exponential phase of growth for C. vulgaris and N. gaditana, while iron was for A. maxima and I. galbana. All species demonstrated their capability to grow in effluents from a wastewater treatment plant and they efficiently consume nitrogen, especially the three microalgae species.

Drug resistance has become an extremely serious problem worldwide. Antibiotic resistance genes (ARGs) entering the environment with wastewaters promote replenishment of the resistome of natural microbioms. Distribution of several clinically significant ARGs in wastewaters of Rostov-on-Don (Southern Russia), lower reaches of the Don River and natural waters of the neighboring region was investigated. Metagenomic DNA samples isolated from 250 ml of wastewaters or natural waters and 200 mg of surface sediments were used for the study. Identification of the ARGs was carried out with end-point detection PCR. Presence of NDM, OXA-48, CTX-M, VanA, VanB, ErmB, and TetM/TetO genes was detected in urban wastewaters. Samples of wastewater treatment plant (WWTP) sewage were enriched with ARGs in contrast to non-treated wastewaters from the sewage collector. NDM, VanA, ErmB, TetM/TetO genes were found only in wastewaters and were absent in samples of natural waters and surface sediments. Only OXA-48, VanB and CTXM genes were found in natural waters and surface sediments. The described ARGs are quite typical for urban and hospital wastewaters. The target ARGs were detected in the samples connected to the anthropogenous sources of pollution such as Rostov municipal WWTP or livestock enterprise effluents.

We report magnetic silver nanoshells (M AgNSs) that have both magnetic and SERS properties for SERS-based detection. The M AgNSs are composed of hundreds of Fe3O4 nanoparticles for rapid accumulation and bumpy silver shell for sensitive SERS detection by near-infrared laser excitation. The intensity of the SERS signal from the M AgNSs was strong enough to provide single particle-level detection. We obtained much stronger SERS signal intensity from the aggregated M AgNSs than from the non-aggregated AgNSs. 4-Fluorothiophenol was detected at concentrations as low as 1 nM, which corresponds to 0.16 ppb. The limit of detection for tetramethylthiuram disulfide was 10 μM, which corresponds to 3 ppm. The M AgNSs can be used to detect trace amounts of organic molecules using a portable Raman system.

Background: Artificial intelligence can help improve the quality of healthcare by analyzing vast amounts of data and providing more effective and personalized treatment plans. Researchers are working on developing AI-powered solutions that can help improve the outcomes of patients. Objective: To explore the potential of AI in improving healthcare outcomes and patient experience. Results: The study suggests that AI can improve healthcare efficiency and patient outcomes but cannot fully replace human healthcare professionals. AI can assist healthcare professionals in their work, leading to better resource utilization and improved patient care. However, there is still a need for human healthcare professionals to oversee AI systems and provide empathy and personalized care to patients. Conclusion: While there is immense potential for AI in healthcare, it is not yet feasible to replace human healthcare workers. Instead, it should be viewed as a tool that can help improve the efficiency and effectiveness of human healthcare.

Time-series analysis is a widely used technique across various fields and industries, as it helps in understanding, predicting, and forecasting the behavior of data points over time. These fields include but are not limited to finance, economics, healthcare, transportation, etc. In the case of this paper, we have focused on finance. Predicting future values of financial time series offers several benefits. Accurate forecasts can help investors make better decisions about their investments. To predict future values, deep learning algorithms are commonly used since it is an effective method with complex data. In this study, we conduct a study that investigates the use of different data pre-processing techniques on deep learning algorithms in predicting the time series values. To conduct this experimental study, we utilize an open source software, which using long short-term memory technique as the representative deep learning technique, published in github software code repository platform. With this study, we investigate the effects of autoencoder and discrete wavelet transform data pre-processing techniques in time-series prediction. We discuss the details of the experimental study and report our results. The results show that time series prediction (using backtesting methodology) without any data pre-processing leads to 12.6% for mean absolute percentage error. The results also show that, time series prediction with the data preprocessing techniques (Wavelet Transform and Stacked Autoencoder) lead to 3.4%

Isothermal Nucleic Acid Amplification based-Lateral Flow Testing (INAA-LFT) has emerged as a robust technique for on-site pathogen detection, providing a visible indication of pathogen nucleic acid amplification that rivals or even surpasses the sensitivity of real-time quantitative PCR. The isothermal nature of INAA-LFT ensures consistent conditions for nucleic acid amplification, establishing it as a crucial technology for rapid on-site pathogen detection. However, despite its considerable promise, the widespread application of isothermal INAA amplification-based lateral flow testing faces several challenges. This review provides an overview of the INAA-LFT procedure, highlighting its advancements in detecting plant viruses. Moreover, the review underscores the imperative to address existing limitations and emphasizes ongoing research efforts dedicated to enhancing the applicability and performance of this technology in the realm of rapid on-site testing.

Recent literature has seen a rapid expansion in the reference to front-end forensics as an indication of the untapped value of forensic science. While some of these contributions have centered on development of forensic intelligence from a single area of investigation, others call for a more fundamental change in the relationship between crime laboratories and policing, particularly relating early laboratory analysis with big datasets to provide leads to investigators. We highlight several recently implemented tactical strategies of crime laboratories that contribute to the body of forensic intelligence. Beyond the scientific gains from these tactical applications, the corresponding details on associated efficiencies, costs, time savings, and quality improvements offer insights towards patterns of success for the community of crime laboratories. Further details expand an interpretation of what constitutes success with an eye on the contributions of the crime laboratory towards public health, safety, and protection of the innocent in addition to societal gains from conviction of the guilty. The economic interpretation of the value provided by the forensic laboratory assists in the cost-benefit review of strategic and tactical decisions and supports the justification for laboratory public funding with measures of the return on investment from public support of the forensic laboratory

The short-lived positron-emitter carbon-11 (t1/2 = 20.4 min; b+, 99.8%) is prominent for labeling tracers for use in biomedical research with positron emission tomography (PET). Carbon-11 is produced for this purpose with a cyclotron, nowadays almost exclusively by the 14N(p,a)11C nuclear reaction, either on nitrogen containing a low concentration of oxygen (0.1–0.5%) or hydrogen (~ 5%) to produce [11C]carbon dioxide or [11C]methane, respectively. These primary radioactive products can be produced in high yields and with high molar activities. However, only [11C]carbon dioxide has some utility for directly labeling PET tracers. Primary products are required to be converted rapidly and efficiently into secondary labeling synthons to provide versatile radiochemistry for labeling diverse tracer chemotypes at molecular positions of choice. This review surveys known gas phase transformations of carbon-11 and summarizes the important roles that many of these transformations now play for producing a broad range of labeling synthons in carbon-11 chemistry.

The mechanical effects of membrane compositional inhomogeneities are analyzed in a process analogous of neck formation in cellular membranes. We cast on the Canham-Helfrich model of fluid membranes with both the spontaneous curvature and the surface tension being non-homogeneous functions along the cell membrane. The inhomogeneous distribution is determined by the equilibrium mechanical equations and the boundary conditions as considered in the axisymmetric setting compatible with the necking process. To establish the role played by mechanical inhomogeneity, we focus on the catenoid, a surface of zero mean curvature. Analytic solutions are shown to exist for the spontaneous curvature and the constrictive forces in terms of the border-radii. Our theoretical analysis shows that the inhomogeneous distribution of spontaneous curvature in a mosaic-like neck constrictional forces potentially contributing to the membrane scission under minimized work in living cells.

The way Norway is spearheading electrification in the transport sector is of global interest, and details of its policies and emission impacts represent a reference. We used the NERVE model, a bottom-up high-resolution traffic emission model, to calculate all exhaust emissions in Norway (2009-2020). This allows us to evaluate the co-benefit of policies to target climate change mitigation and air quality. We have analyzed local municipal data with regards to traffic growth, road network influences, vehicle composition, emissions and energy consumption. Light vehicle CO2 emissions per kilometre have been reduced by 22% since 2009, mainly driven by an increaseing bio-fuel mixing and BEV share. BEVs are mostly located in and around the main cities, areas with young vehicle fleets, and strong local incentives. Beneficiaries of all BEVs incentives have been a subset of the population with strong economic indicators. The incentivized growth in the share of diesel-fuelled passenger vehicle has been turned, and together with Euro6 emission standards, light vehicle NOx emissions have been halved since peaking in 2014. BEV represent an investment in emission reductions in years to come and current sales set up for an accelerated decline in emissions despite growth in traffic.

The on-state voltage of MOSFETs is a convenient and powerful temperature-sensitive electric parameter (TSEP) to determine the junction temperature, thus enabling device monitoring, protection, diagnostics and prognostics. The main hurdle in the use of the on-state voltage as a TSEP is the per-device characterization procedure, to be carried out in a controlled environment, with high costs. In this paper we compare two novel techniques for MOSFET junction temperature estimation: controlled shoot-through and direct heating by resistive heaters embedded in two Kapton (polyimide) films. Both allow in-place characterization of the TSEP curve with the device mounted in its final circuit and assembly, including the working heat sink. The two methods are also validated against the conventional procedure in a thermal chamber.

Introduction: In general, everyone believes that the smallest preterm infants should achieve normal intrauterine growth rates, but many thinks that this is not possible with current nutrition guidelines. There is resistance to giving enough nutrition for fear of "toxicity". The difference in weight Z-score between birth and a corrected gestational age (CGA) at discharge is assess in postnatal growth in our unit. Material and methods: An observational study was done between January 2018 and December 2020 where all cases that had ≤ 29 weeks of GA at birth and survived to 36 weeks corrected GA or that were discharged home. An aggressive nutrition protocol including parenteral as well as enteral nutrition was followed. Patients and their weight trajectory was plotted on the Fenton 2013 growth curve. The patients who had had a smaller WZP difference were also plotted. Results: A total of 32 cases were found. The median change in Z-score between birth and discharge of the whole group was -0.52 (IQR 0.53). Six of 32 (19%) had a more than one WZP, all of whom had severe pathologies. The median decline in Z score for this group with poor growth was 1.24 (IQR 0.22). There were 26 cases with a < 1 WZP (81%) and a median Z score fall of 0.39 (IQR 0.55). No important complications secondary to the ingested volumes or parenteral nutrition were reported. Conclusion: The group of cases with a > 1 WZP drop had severe pathologies. All the other cases had adequate growth parallel to normal weight growth charts and a few cases had some catch-up growth. The study showed that it is possible for many preterm infants to achieve normal intrauterine growth rates if they are given enough nutrition, but bigger multicenter studies are needed to confirm these findings.

Saiga (Saiga tatarica) was extirpated in China. Since Mid-1980s, attempts have been made for revival the species in the country, however, only a breeding herd of Saiga was successfully established at Wuwei, Gansu, China. The reintroduced Saiga population experienced a bumpy growth. Then, the population collapsed following the catastrophe die-off in the Saiga ranging countries in Central Asia, then population started to rebound when 6 new lams were born in 2019. After reviewing the population trend and conservation breeding of Saiga in China, we concluded that to establish a migratory species that needs vast range size like Saiga on central Asia steppe, an international collaboration is needed for introducing new genes. We recommend China to ratify the CMS in order to facilitate international conservation efforts to restoring the species in its former range.

Microsystems are key enabling technologies, with applications found in almost every industrial field, including in-vitro diagnostic, energy harvesting, automotive, telecommunication, drug screening, etc. Microsystems, such as microsensors and actuators, are typically made up of components below 1000 microns in size that can be manufactured at low-unit cost through mass-production. Yet, the development of microsystems for commercial or educational purposes, has typically been limited to upper income countries due to the initial investment costs associated with the microfabrication equipment and processes. However, recent technological advances have enabled the development of low-cost microfabrication tools. In this paper, we describe a range of low-cost approaches and equipment (below £1000), developed or adapted and implemented in our laboratories. We describe processes including photolithography, micromilling, 3D printing, xurography and screen-printing used for the microfabrication of structural and functional materials. The processes that can be used to shape a range of materials with sub-millimetre feature sizes are demonstrated here in the context of Lab-on-Chips, but they can be adapted for other applications. We anticipate that this paper, which will enable researchers to build a low-cost microfabrication toolbox in a wide range of settings, will spark a new interest in microsystems.

Manufacturing of grinding wheels is continuously adapting to new industrial requirements. New abrasives and new wheel configurations, together with wheel wear control allow for grinding process optimization. However, the wear behavior of the new abrasive materials is not usually studied from a scientific point of view due to the difficulty to control and monitor all the variables affecting the tribochemical wear mechanisms. In this work an original design of pin on disk tribometer is developed in a CNC grinding machine. An Alumina grinding wheel with special characteristics is employed and two types of abrasive are compared: White Fused Alumina (WFA) and Sol-Gel Alumina (SG). The implemented tribometer reaches sliding speeds of between 20 and 30 m/s and real contact pressures up to 190 MPa. The results show that the wear behavior of the abrasive grains is strongly influenced by their crystallographic structure and the tribometer appears to be a very good tool for characterizing the wear mechanisms of grinding wheels, depending on the abrasive grains.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

Since the systematic evolution of ligands by exponential enrichment (SELEX) method was developed, aptamers have made significant contributions as bio-recognition sensors. Microdevice systems allow for low reagent consumption, high-throughput of samples, and disposability. Due to these advantages, there has been an increasing demand to develop microfluidic-based aptasensors for analytical technique applications. This review introduces the principal concepts of aptasensors and then presents some advanced applications of microdevice-based aptasensors on several platforms. Highly sensitive detection techniques such as electrochemical and optical detection have been integrated into lab-on-a-chip devices and researchers have moved towards the goal of establishing point-of-care diagnoses for target analyses.

This article presents and discusses analytical data on the scientific publication record from 1910 to 2020 on two topics: "climate" and "climate change/global warming/climate emergency". The goal is to visualize how the publication record on these two topics has evolved over time, from different classification perspectives (year, country, source and organization). Three hypotheses are tested using data collected from Web of Science and various graphical representations of the data. It is found that research output related to the Earth’s contemporary changing climate overtook that of general climate research in 2011, and the publication ratio has been expanding in the last decade. There are significant differences in the publication countries and sources between the two topics, and conversely less significant differences in terms of organizations publishing these works. Differentiation factors that affect the level of research output and engagement on the climate challenge include: island versus landlocked nations, specialized versus general scientific journals, academic versus institutional organizations. The future of the publication records is discussed, such as the emergence of new terms to refer to the climate challenge, such as “climate emergency”.

(1) Background: Since the pandemic, adolescent girls have increasingly faced mental health challenges. We examined prevalence trends and associated risk factors for depression among adolescent girls. 2) Methods: Data for girls aged 12 to 17 years (N=4346) from the 2021 cross-sectional National Survey on Drug Use and Health were analyzed. Factors associated with depression were examined using multiple regression analysis. (3) Results: Rates of severe depression were significantly higher (p&lt;.001) in older girls (adjusted odds ratio [AOR]: 1.63, 1.61, those who did not have authoritative parents (AOR: 3.40), and those with negative school experiences (AOR: 4.03). Black and Asian/Native Hawaiian or other Pacific Islanders were less likely to report severe depression than white girls. As previously reported, non-White girls were significantly less likely to receive treatment for depression (p&lt;.05). Parents’ characteristics and school experiences had no effect on the likelihood of receiving mental health treatment. (4) Conclusion: Depression has become increasingly common among American adolescent girls, who are now three times as likely as adolescent boys to have had recent experiences with depression. Our results show that family structure, parenting style, and negative school experiences significantly contribute to the rate of depression and that treatment disparities exist with regard to race and ethnicity.

This proposed research explores a novel approach to image classification by deploying a complex-valued neural network (CVNN) on a field-programmable gate array (FPGA), specifically for classifying 2D images transformed into polar form. The aim of this research is to address the limitations of existing neural network models in terms of energy and resource efficiency, by exploring the potential of FPGA-based hardware acceleration in conjunction with advanced neural network architectures like CVNNs. The methodological innovation of this research lies in the Cartesian to polar transformation of 2D images, effectively reducing the input data volume required for neural network processing. Subsequent efforts focused on constructing a CVNN model optimized for FPGA implementation, emphasizing the enhancement of computational efficiency and overall performance. The experimental findings provide empirical evidence supporting the efficacy of the image classification system developed in this study. One of the developed models, CVNN_128, achieves an accuracy of 88.3% with an inference time of just 1.6ms and a power consumption of 4.66mW for the classification of the MNIST test dataset consists of 10,000 frames. While there is a slight concession in accuracy compared to recent FPGA implementations that achieve 94.43%, our model significantly excels in classification speed and power efficiency—surpassing existing models by more than a factor of 100. In conclusion, the paper demonstrates the substantial advantages of FPGA-implementation of CVNNs for image classification tasks, particularly in scenarios where speed, resource, and power consumption are critical. The study’s reproducible results and corresponding code are available on GitHub at the following link: https://github.com/mahmad2005/CVNNonFPGA

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

Influence of reaction time on silver nanoparticles-catalyzed oxidation of 3,3’,5,5’-tetramethylbenzidine (TMB) was evaluated via probing the oxidation process by recording the UV-Visible absorbance of the resulting colored products of TMB oxidation by hydrogen peroxide in the presence of silver nanoparticles as peroxides mimics. The time curve of the oxidation process was constructed, revealed that the concentration of the oxidation product was increased by increasing the reaction time and then levled off because the nanozyme active nodes were saturated after a certain reaction time and consequently the steady-state condition can be observed. The maximal activity of the silver nanozymes was achieved after a very short reaction time as short as 3.0 min and after this time, the color intensity of the oxidation products remained constant, revealing saturation of active nodes of nanoparticles with nanozyme-substrate.

Keywords: Kenaf; liquid cultivation; solid cultivation; in vitro propagation, life on land

The idea of an extension of life for CubeSats is proposed to reduce space debris in a low-earth orbit. In this work, a gripper is designed for geometry-based grasping in berthing tasks. The grasping operation is outlined for square- and rectangle-profiled CubeSats. Equilibrium conditions are used to choose fingertips shape and parameters for grasping the CubeSat body. A design scheme is proposed to provide the required accuracy. A design concept is developed into a lab prototype by using low-cost 3D printing technique, and a mock-up grasping task that is representative of the berthing operation is evaluated with the lab prototype. Center-mass hanging setup for the prototype and grasped body is used to evaluate the impact of grasping, partially replicating the conditions in space by reducing the effect of gravity on the system.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

This article aims to reflect upon the relevance of Decolonization methodologies with the Theses on Feuerbach. Somehow, all the Indigenous scholars started from new Marxist like Paulo Freire, Frantz Fanon, but not from classic Marx. To us, the German Ideology of young Marx only resembles the pioneering sources of Indigenous methodology. This discussion is thus a reflection of our studies and a philosophic endeavor to talk about the marginal people of the world, and the scholars who engaged in and with the oppressed. However, we are not prepared to turn our attention away from all the vastness of Marx to a collection of potentially equally relevant to Indigenous methodology. This article concludes that the Theses on Feuerbach is the core of Marxist archaeology of knowledge or philosophy as a whole and has been wading in the Indigenous paradigm.

The contactless coalescence of a droplet is of paramount importance for physical and industrial applications. This paper describes a coalescence method in mid-air via acoustic levitation using an ultrasonic phased array system. Acoustic levitation using ultrasonic phased arrays provides promising lab-on-a-drop applications, such as transportation, coalescence, mixing, separation, evaporation, and extraction in a continuous operation. The mechanism of droplet coalescence in mid-air may be better understood by experimentally and numerically exploring the droplet dynamics immediately before the coalescence. In this study, water droplets were experimentally levitated, transported, and coalesced by controlling acoustic fields. We observed that the edge of droplets deformed and attracted each other immediately before the coalescence. Through image processing, the radii of curvature of the droplets were quantified and the pressure difference between the inside and outside the droplet was simulated to obtain the pressure and velocity information on the droplet surface. The results revealed that the sound pressure acting on the droplet clearly decreased before the impact of the droplets. This pressure on the droplets was quantitatively analyzed from the experimental data. Our experimental and numerical results provide deeper physical insights into contactless droplet manipulation for futuristic lab-on-a-drop applications.

Marine mortar was the goal material and its multi-scale physical-chemical-mechanical characteristics were the principal interest in this study. The on-line multi-scale damage detection experiments art was designed to quantify the characteristics mathematically and graphically. The normal cylinder specimen with 70-day age was produced and investigated by dynamically global MSHCT scan and local detection of EDS, SEM and XRD. The experiments results indicated that the marine mortar offered the appreciable strength at the early age at least, although some saline minerals were generated during the preparation. The micro-interfacial behavior and the parental foci controlled the damage development of the marine mortar the performance of which was still the adjustable one by the composition optimization.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

This study was aimed to investigate the effect of capital structure on firms’ profitability with special emphasis on Ethiopian Large Private Manufacturing Firms using panel data of five consecutive years (2006/07-2010/11G.C). The secondary data sources (audited financial statements) have been collected from the randomly selected thirty three large private manufacturing firms in Ethiopia. Linear regression model has been employed to analyze the relationship between firms’ profitability and capital structure. Specifically, Random-effect Generalized Least Square of panel data regression model has been selected to empirically test the literature driven hypotheses. Finally, the findings of this study revealed that a significant positive relationship between firms’ profitability and total debt ratio which indicate firm’s capital structure.

Biomaterials play an important role in the development of advancing three dimensional (3D) in vitro skin models, providing valuable insights for drug testing and tissue-specific modeling. Commercial materials, such as collagen, fibrin or alginate, have been widely used in skin modelling. However, they do not adequately represent the molecular complexity of skin components. On this regard, the development of novel biomaterials that represent the complexity of tissues are becoming more important in the design of advanced models. In this study, we have obtained aged human decellularized dermal extracellular matrix (dECM) hydrogels extracted from cadaveric human skin and demonstrated their potential as scaffold for advanced skin models. These dECM hydrogels effectively reproduce the complex fibrillar structure of other common scaffolds, exhibiting similar mechanical properties, while preserving the molecular composition of the native dermis. It is worth noting that fibroblasts embedded within human dECM hydrogels exhibit behavior more representative of natural skin compared to commercial collagen hydrogels, where uncontrolled cell proliferation leads to material shrinkage. The described human dECM hydrogel is able to be used as scaffold for dermal fibroblasts in a skin aging on chip model. These results demonstrate that dECM hydrogels preserve essential components of the native human dermis making them a suitable option for the development of 3D skin aging models that accurately represent the cellular microenvironment, improving existing in vitro skin models and allowing for more reliable results in dermatopathological studies.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

This study presents the design and implementation of a PLC microprocessor adhering to the IEC-61131-3 standard, executed on a Cyclone-V FPGA using a DE10-NANO development board. Our microprocessor optimizes the central processing unit by streamlining the data path, achieving a remarkable simulated response time of approximately 60 ns, equivalent to three clock cycles at a 50MHz frequency for Boolean operations. To substantiate our approach, we conducted practical experiments utilizing a FESTO conveyor station, employing relays as actuators, and incorporating optical and inductive sensors. The results underscore the feasibility of our proposed approach and serve as practical validation of its efficacy. This work introduces a promising avenue for the development of cost-effective PLCs employing SoC FPGA variants. Additionally, a thorough comparison of execution times with other early reported architectures. Our microprocessor outperforms even well-established PLCs like the S7-312, with substantial reductions in execution times of 94.54% for floating-point operations, 71.42% to 93.33% for word operations, and up to 78.57% for bit operations.