Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

On-chip integration of two-dimensional (2D) materials with unique structures and distinctive properties endow integrated devices with new functionalities and improved performance. With a high flexibility in modifying its properties and a strong compatibility with various integrated platforms, graphene oxide (GO) becomes an attractive 2D material for implementing functional hybrid integrated devices. Here, we demonstrate novel functionalities that go beyond the capabilities of conventional photonic integrated circuits, by harnessing the photo-thermal effects in 2D GO films integrated onto them. These include all-optical control and switching, optical power limiting, and non-reciprocal light transmission. The 2D layered GO films are on-chip integrated with precise control of their thicknesses and sizes. Benefitting from the broadband response of 2D GO films, all the three functionalities feature a very wide operational bandwidth. By fitting the experimental results with theory, we also extract the changes in material properties induced by the photo-thermal effects, which reveal interesting insights about 2D GO films. These results highlight the versatility of 2D GO films in implementing functional integrated photonic devices for a range of applications.

Magnetic ceramic nanoparticles system xTm2O3-(1-x)alpha-Fe2O3 (x=0.1 and 0.5) was synthesized by mechanochemical activation starting from hematite and thulium oxide precursors and characterized by transmission Mӧssbauer spectroscopy. The Mӧssbauer spectra were typically analyzed considering 1-3 sextets, corresponding to hematite (with and without thulium doping) and a doublet, representing thulium iron perovskite (thulium orthoferrite). The magnetic hyperfine fields (BHF) and doublet abundance were studied as function of the ball milling time (BMT) for both molar concentrations employed. The results are consistent with the formation of solid solutions in the investigated system. The mixed-oxide nanoparticle system synthesized may have important applications in displays, sensors and photovoltaics, and is paving the way for emerging utilizations related to mechanically flexible electronics.

Electrowetting – induced detachment of droplets from solid surfaces is important for numerous applications in the fields of heat transfer and fluid mechanics. The forced oscillations of droplets on solid surfaces and their ability to detach are studied. In this study the process is efficiently simulated by implementing a powerful methodology developed by our team. Our results agree with experiments, showing that optimal detachment, in terms of actuation energy, is achieved when the application of voltage is synchronized with the spreading time of the droplet. Under these conditions, the droplet oscillates with a period close to that of a mirrored Rayleigh droplet. The relation between the droplet’s oscillation period and its physical properties is examined. During voltage-droplet synchronization, the droplet’s ability to detach depends mostly on its contact angle, its viscosity, and the applied voltage. An energy analysis is also conducted, revealing how energy is supplied to the droplet by electrowetting-induced detachment.

As the global community shifts away from fossil fuels towards more environmentally friendly energy alternatives, there is an escalating demand for sophisticated energy storage solutions. Solid-State Batteries (SSBs) have emerged as a promising advancement, presenting a superior substitute to conventional lithium-ion batteries. This review provides an in-depth examination of SSBs, emphasizing their enhanced energy density, safety, and longevity. We evaluate conventional cathode materials, including lithium cobalt oxide (LiCoO2), lithium manganese oxide (LiMn2O4), and lithium iron phosphate (LiFePO4). Additionally, we introduce emerging materials such as sulfides, oxides, and air-based cathodes, discussing their benefits, limitations, and their congruence with solid electrolytes. Special attention is devoted to the structural fine-tuning of cathode ma-terials, investigating approaches like nanostructuring, surface coatings, and composite strategies to counteract issues such as restricted conductivity and structural volatility. The review critically analyzes the electrical and thermal properties of these materials, which are essential for battery safety and efficacy. Moreover, we present a comparative assessment of cathode materials based on performance indicators and identify prevailing research voids and hurdles in the commerciali-zation of SSB cathodes. Concluding, we suggest prospective research directions and innovations, underscoring the revolutionary potential of SSB technologies in paving the way for a sustainable energy horizon.

This study focuses on the increased risk of high heat release and asphyxiation (toxic gas poisoning) in the event of a fire of polyurethane (PU) and MDF-based building materials, which are commonly used in building fires. Among them, polyurethane (PU) building materials are essential for buildings except in Europe and some other countries due to their excellent thermal insulation performance, but problems of short-term heat release and spread of toxic gases in the event of a fire continue to occur. To overcome these problems, researchers are actively working on introducing various flame retardants into building materials. Therefore, in this study, we produced a laboratory-sized (500mm*500mm) plate flame retardant board that can be utilized as a building material with a lower heat release rate and a lower toxicity index by mixing expanded graphite and ceramic binder as flame retardants in a main material based on the cellulose of waste paper by replacing the existing building materials with a hot-press method. According to the ISO-5660-1 test on the heat release rate of the plate flame retardant board, the THR value was 2.9 (MJ/m2) for 10 minutes, showing an effect of reducing the THR value by 36.3 (MJ/m2) compared to the THR value of 39.2 (MJ/m2) of the specimen made using only paper. In addition, the toxicity index of the flame retardant board was checked through the NES 713 test. As a result, the test specimen showed a toxicity index of 0.7, which is 2.4 lower than the toxicity index of 3.1 of MDF, which is utilized as a conventional building material. Based on the results of this study, the cellulose fire retardant board showed the effect of reducing the heat release rate and toxicity index of building materials in a building fire, which reduces the risk of rapid heat spread and smoke toxicity. This has the potential to improve the evacuation time (A-SET) of evacuees in fires. It is also important to show that recycling waste paper and utilizing it as the main material for building materials can be an alternative in terms of sustainable development.

In Geo Polymer bricks (GPB), fly ash content which is a waste from power plants is converted into bricks by chemical treatment. GPB can be dried by using appropriate curing methods. Conven-tionally electric oven curing is one of the prominent methods. Using solar dryer instead of elec-trical oven gives added advantage of saving high grade electrical energy. So in this work solar dryer with PCM (Phase Change materials) Paraffin Wax and without PCM is used for curing ap-plication. GPB are gaining added advantage when compared to conventional bricks like cement and sand bricks in terms of strength. GPB has been taken as specimen for comparing the com-pressive, tensile split strength and flexural strength by electrical energy based curing and solar energy based curing. It is experimentally observed that solar energy based curing with PCM and without PCM exhibits higher compressive strength, higher tensile split strength and flexural strength when compared to electrical energy based curing. Solar curing with PCM shows higher compressive strength, higher tensile split strength and flexural strength when compared to Solar curing without PCM. Open solar curing is a traditional technique but nowadays aggressive cli-matic conditions can lead to severe damage of Geo polymers. The novelty of this work is to suggest to study the effect of PCM like paraffin wax in solar drying on curing time, mechanical properties of GPB.

In the seasonally frozen regions, during the grouting of prestressed bridge ducts in low-temperature environments, incompletely cured grout materials undergo volumetric changes due to the freeze-thaw cycling, resulting in structural cracks along the prestressing ducts of the bridge, thereby diminishing the bridge's operational lifespan. To investigate the frost heaving characteristics of grout materials under freeze-thaw cycles and propose potential enhancements, this study was devised to conduct frost heaving stress tests on grout materials. Through this research, we gained insights into how various additives affect the frost heaving stress characteristics of grout materials under freeze-thaw cycles. Incorporating analyses of free water content, setting time, compressive strength, as well as macroscopic examinations such as XRD and SEM, this study delves into the mechanisms for enhancing frost heaving characteristics of grout materials. Furthermore, it proposes a research approach that utilizes multiple admixtures to improve the frost heaving properties of grout materials. Through frost heaving stress tests and other macroscopic experiments, the study investigates the influence of these combined admixtures on frost heaving stress in grout materials and elucidates the underlying improvement mechanisms. The results indicate that reducing the water-cement ratio, incorporating calcium formate, sulfoaluminate cement, air-entraining agents, and carbamide all have a positive impact on mitigating frost heaving stress in grout materials. However, the improvement mechanisms differ, and employing a single measure alone is insufficient to effectively reduce frost heaving stress while meeting performance criteria such as compressive strength, setting time, and flowability. Free water content emerges as a crucial indicator determining the magnitude of frost heaving stress in grout materials, with 11.5% of free water content representing the critical threshold for frost heaving in grout materials. Utilizing composite admixtures can simultaneously decrease free water content, lower the freezing point of free water, and alleviate frost heaving deformation, resulting in more efficient reduction of frost heaving stress. When the admixture content reaches 9.9%, frost heaving stress is eliminated, and the comprehensive performance parameters including compressive strength, setting time, and flowability meet the specified requirements.

Target detection of defense technology is being rapidly upgraded with modern surveillance technologies. The latest techniques of surveillance are already being implemented for defense applications. Self-protection and hiding from opposing forces are the key principle for protection of special team in defense. Camouflage textiles aims to create confusing objects for target detection of military personnel. These textiles are applied for military protection such as clothing, weapon, vehicle and location hiding nets/tents, etc. The urgent need of camouflage textiles have been formulated with a technical solution and implementation of right camouflage materials for concealment of defense target signature against dry leaves, green leaves, tree bark-woodland combat background; water-marine combat background; sand-desertland combat background; stone-stoneland combat background; snow-snowland combat background; sky combat background and ice-iceland combat background, concrete-concreteland combat background (DGTWSICB) in ultraviolet-visible-infrared (UV-Vis-IR) spectrums. This hypothesis of optical & surveillance engineering has been coalesced for advancement of UV-Vis-IR-DGTWSICB camouflage textiles technology. The principle of camouflage engineering has been approached by broader spectrum probe in UV-Vis-IR rather than Vis ranges only. Furthermore, single formulation of camouflage textiles has been proposed for multidimensional CBs-DGTWSICB. Electromagnetic spectrum, reflection, electron energy, photonic signal and imaging mechanism in UV-Vis-IR have been presented for optical engineering of concealment, detection, recognition and identification of target signature against DGTWSICB. Spectrum relationship of camouflage materials and DGTWSICB materials have been illustrated and compared in UV-Vis-IR spectrums. Camouflage material design, method design & spectral design; adaptive camouflage; techniques for camouflage textile assessment for digital camera and hyperspectral camera imaging; image processing techniques and a hierarchical model have been demonstrated for augmentation of camouflage textiles in UV-Vis-IR illumination. Therefore, anticipated design of camouflage textiles may enhance high-performance innovation for modern surveillance of military protection related to digital camera, hyperspectral camera and radar. This hypothesis includes advance guideline for camouflage textiles design for CBs-DGTWSICB.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.

This study aims to comprehensively compare and evaluate the toughening effects of different nanocarbon materials on vinyl ester resin composites. The incorporation of nanocarbon materials has gained significant attention due to their potential to enhance the mechanical properties of polymers. In this research, carbon nanotubes (CNTs), graphene nanoplatelets (GNPs), and carbon nanofibers (CNFs) were chosen as nanocarbon additives. The mechanical properties, including tensile strength, flexural strength, and impact strength, were systematically investigated and compared for each nanocomposite. Additionally, microstructural analysis was conducted using scanning electron microscopy (SEM) to understand the dispersion of nanocarbon materials within the vinyl ester matrix. The results indicated that all three nanocarbon materials contributed to the toughening of the vinyl ester resin, with varying degrees of improvement in mechanical properties. This study provides valuable insights into the selection of nanocarbon additives for enhancing the toughness of vinyl ester resin and offers guidance for designing advanced polymer composites.

Mechanical engineering plays an important role in the design and manufacture of medical devices, implants, prostheses, and other medical equipment, where the machining of bio-compatible materials have a special place. There are a lot of different conventional and non-conventional types of machining of biocompatible materials. One of the most frequently used methods is milling. The first part of this paper considers the optimization of machining parameters for minimizing surface roughness in milling biocompatible alloy Ti-6Al-4V. With four factors (cutting speed, feed rate, depth of cut, and cooling/lubricating method), each having three levels, the full factorial design implies 81 experiments have to be carried out. Using the Taguchi method, the experiment number was reduced from 81 to 27 runs through an orthogonal design. According to the analysis of variance (ANOVA), the most significant parameter for surface roughness is feed rate. In the second part possibilities of different ML techniques to create a predictive model for average surface roughness using previously created small dataset are explored. Several ML technologies and techniques that can deal successfully with small dataset were explored. The best results show commonly used machine learning algorithm Random Forest that is widely used in regression problems.

(1) Background: The compound ytterbium trifluoride is used as a component of several dental materials, and this is reviewed in the current article. (2) Methods: Published articles on this substance were identified from PubMed, and showed that it has been included in a variety of dental restorative materials, including composite resins, glass polyalkenoate cements and calcium trisilicate cements. (3) Results: Ytterbium trifluoride is reported to be insoluble in water. Despite this, its presence is associated with fluoride release from dental materials. There is evidence that it reacts with the components of calcium trisilicate cements to form small amounts of a variety of compounds, including ytterbium oxide, Yb2O3, and calcium-ytterbium fluoride, CaYbF5. In nanoparticulate form, it has been shown to reinforce glass polyalkenoates and it also provides high contrast in X-ray images. (4) Conclusions: Ytterbium trifluoride is a useful component of dental materials, though some of the published findings suggest that there are aspects of its chemistry which are poorly understood.

This article is a scoping review analyzing advances in experimental studies on bacterial self-healing of concrete. From Scopus, ScienceDirect, Web of Science and Google Scholar search engine databases, 54 studies were selected for analysis, and an increasing trend of publications since 2015 was found, with India as the country with the largest research presence. Different ma-terials are used as replacement or admixture in concrete, such as fibers, particles and recycled material from construction waste. It was found that the most commonly used bacteria are Bacillus subtilis and Bacillus sphaericus, which can improve the strength of concrete by generating calcite and sealing cracks. In addition, it was found that the presence of materials such as fibers, ashes and construction recyclates can protect bacteria in an alkaline environment. The designs usually in-clude more than two experimental groups and a control. In summary, this study highlights the importance of bacterial self-healing in concrete and provides information on advances in this field of research.

The redox properties of quinones underlie their unique characteristics as organic battery components that outperform the conventional inorganic ones. Furthermore, the redox properties could be precisely shaped by using different substituent groups. Machine learning and statistics, onthe other hand, have proven to be very powerful approaches for efficient in silico design of novel materials. Herein, we demonstrated the machine learning approach for the prediction of the redox activity of quinones that potentially can serve as organic battery components. For the needs of the present study, a database of small quinone-derived molecules was created. A large number of quantum chemical and chemometrics descriptors was generated for each molecule and subsequently different statistical approaches were applied to select the descriptors that most prominently characterize the relationship between structure and redox-potential. Various machine-learning methods for screening of prospective organic battery electrode materials were deployed to select the most trustworthy strategy for machine learning aided design of organic redox materials. It was found that ridge regression models perform better than regression decision tree and decision tree based ensemble algorithms.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

In the present study, the efficiency of a biomimetic approach by coating demineralized bone matrix (DBM) amorphous calcium phosphate (DBM+CaP), including its combination with serum albumin (DBM+CaP+BSA), was investigated. The intact structure of DBM promotes the transformation of amorphous calcium phosphate (CaP) into DPCD with a characteristic plate shape and particle size of 5–35 µm. The inclusion of BSA in the coating resulted in a better and more uniform distribution of CaP on the surface of DBM trabeculae. MG63 cells showed that both the obtained forms of CaP and its complex with BSA did not exhibit cytotoxicity up to a concentration of 10 mg/ml in vitro. Ectopic (subcutaneous) implantation in rats revealed pronounced biocompatibility, as well as strong osteoconductive, osteoinductive, and osteogenic effects for both DBM+CaP and DBM+CaP+BSA, but more pronounced effects for DBM+CaP+BSA. In addition, for the DBM+CaP+BSA samples, a pronounced full physiological intrafibrillar biomineralization and proangiogenic effect with the formation of bone-morrow-like niches, accompanied by pronounced processes of intramedullary hematopoiesis, indicating a powerful osteogenic effect of this composite have been achieved.

The global construction sector contributes a significant share of total greenhouse gas (GHG) emissions. In Australia, infrastructure activity alone generates 18% of the GHG emissions budget. The use of low-embodied carbon building materials is crucial to achieving sustainability in the construction sector and to fulfill national and international climate goals. Industrial hemp (Cannabis sativa L.) is considered a promising feedstock for sustainable construction materials because of its biogenic carbon content, fast-growing cycles with low agricultural input requirements, and technical functionality which is comparable to traditional materials. This study has applied the life cycle assessment (LCA) guideline of ISO 14040:2006 to estimate the carbon footprint (CF) expressed in carbon dioxide equivalent (CO2eq) emissions of hemp-based building materials in Western Australia. The functional unit is 1 m2 of hemp-based board, and the system boundary includes cradle-to-gate stages, i.e., pre-farm, on-farm, and post-farm activities. The production of 1 m2 of hemp-based board is estimated to be - 2.302 kgCO2eq. Electricity from the public grid for lignin extraction during the post-farm stage is the main contributor to total CO2eq emissions (26%), followed by urea production (14%) during the pre-farm stage. Overall, the use of electricity from the SWIS during the post-farm stage accounts for 45% of total emissions. Sensitivity analysis shows that the CF of hemp-based boards is highly sensitive to the source of energy, i.e., total replacement of the SWIS by solar power decreases the CF from - 2.30 to -6.07 kgCO2eq (164%). The results suggest that hemp-based boards exhibit lower embodied GHG emissions compared to traditional materials, such as gypsum plasterboards.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

Abstract: Theoretical and non-dimensional investigations have been performed to study the vibration control potential of approaches that can be based on viscoelastic but also on endochronic elements. The latter are known from the endochronic theory of plasticity and provide the possibility to establish rate-independent schemes for vibration control. The main question that has to be answered is: Can rate-independent damping be efficiently used to reduce mechanical vibrations? To answer this question non-dimensional models for dynamical systems are derived and analyzed numerically in time-domain as well as in frequency-domain. The results are used to compare the performance of an optimally tuned endochronic absorber to the performance of an optimally tuned dynamic absorber with viscoelastic damping. Based on a novel closed form representation for non-linear systems with endochronic elements, it has been possible to prove that rate-independent control of vibration results in an overall control profit that is close to the control profit obtained by the application of well-established approaches. It has also been found that the new concept is advantageous if anti-resonances have to be considered in broadband vibration control. Based on these novel findings, a practical realization in the context of active vibration control is proposed in which the rate-independent control law is implemented on an appropriate signal processing hardware.

Sustainable biomass production has significant potential for mitigating greenhouse gas emissions and is a promising alternative for the production of eco-friendly biofuels, biochemicals, and carbonaceous materials for biological, energetic, and environmental applications. Biomass from agroforestry and agricultural wastes is the richest natural carbon source and a sustainable option for woody biomass from a circular economic perspective. Portugal has several residues and by-products of agriculture, food processing, and forestry origin, and has a high availability of residual biomass. Portugal intends to reduce its dependence on energy imports and the use of fossil fuels, thereby increasing its economic performance while using biomass waste to produce high-value-added products. In this context, this review aims to explore the potential of agri-food wastes obtained from Portuguese industries via thermochemical conversion technologies as a promising sustainable alternative to woody biomass for the development of eco-friendly biofuels, biochemicals, and high-value carbonaceous materials and their applications. This strategy based on the circular bioeconomy concept can contribute to reducing the dependence on fossil fuels and minimising greenhouse gas emissions while meeting the demands of the growing population and providing a sustainable waste management solution.

This research work was aimed at investigating and determining the depth resolution of a 500Mhz GPR Antenna. The survey was conducted in an open space at the Physics Department, College of science-KNUST. The MALA GPR equipment with 500MHz shielded Antenna in the common offset-mode was used to investigate the depth at which materials were buried. Concrete block, tree roots, plastic bottle with water, glass bottle and Electric wire were each buried in cavities with five different burial depths. The real depth of each material was measured both along and across the cavity and compared to their corresponding GPR measured depth. The comparison of the Real depth and the GPR depth showed almost identical depth measurements with a root mean square deviation of 0.028m. The implication of this is that the 500 Mhz GPR antenna can accurately locate and detect the position of buried materials in the subsurface at a depth within the range (0.20-0.66) m.

Two-dimensional (2D) bismuth oxyhalides (BiOX) have attracted much attention as potential optoelectronic materials. Expecting for their application diversity, we herewith systematically investigate the tunable properties of 2D BiOX by using first principles calculations. Their electronic and optical properties can be modulated by changing the number of monolayers, applying strain, and/or varying the halogen composition. The bandgap shrinks monotonically and approaches the bulk value, the optical absorption coefficient increases, and the absorption spectrum redshifts, as the layer number of 2D BiOX increases. Carrier transport property can be improved by applying tensile strain, and the ability of photocatalytic hydrogen evolution can be obtained by applying compressive strain. General strain engineering will be effective in linearly tune the bandgap of BiOX in a wide strain range. Strain together with halogen composition variation can tune the optical absorption spectrum to be on demand in the range from visible to ultraviolet. It suggests that that 2D BiOX materials have potential serving as tunable novel photodetectors, can be used to improve clean energy techniques, and are prospective in the field of flexible optoelectronics.

Advanced composite materials have drawn significant interest in the last years as an alternative to traditional materials due to their higher performance. However, industry struggle to provide low-cost, higher occupational safety, lower footprint with composites, making them suitable for holistic analyses. Therefore, the material design becomes an essential element that can impact the competitiveness, particularly in terms of productivity, circularity, safety, sustainability, and quality of the value chain. The Material Design-for-eXcellence is a state-of-art methodology for material performance multi-dimensional assessment along its life cycle phases, either useful to support ma-terial selection for new products or also to new material design support optimizing resource effi-ciency. In this methodology, the material behaviour and its multiple characteristics assessment, and the manufacturing processes efficiency are evaluated. The framework considers the analogy of product design holistic approaches, as Lean Design-for-X, to organize and assess the mul-ti-dimensional performance for each “X” Material Property. In this work, it was possible to observe that the bio-based composites solutions could be a good sustainable alternative for several sectors. Every day researchers are creating more new materials, having a diversity of properties at different scales, Material Design-for-eXcellence must also in the near future consider other factors. Hence, additional studies are thus foreseen to explore and develop this new tool.

We studied the magnetostriction coefficients, λs, Curie temperature, Tc, and their dependence on annealing conditions in Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 amorphous glass-coated microwires with rather different character of hysteresis loops. A positive λs≈20x10-6is observed in as-prepared Fe47Ni27Si11B13C2, while low and negative λs ≈-0.3x10-6 is ob-tained for Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 microwire. Annealing affects the magnetostriction coeffi-cients and Curie temperatures, Tc, of both Fe47Ni27Si11B13C2 and Co67Fe3,9Ni1,5B11,5Si14,5Mo1,6 glass-coated microwires in a similar way. Observed dependencies of hysteresis loops, λs and Tc on annealing conditions are discussed in terms of superposition of internal stresses relaxation and structural relaxation of studied microwires. We observed linear λs dependence on applied stress, σ, in both studied microwires. A decrease with applied stress is observed for Co-rich mi-crowires with negative magnetostriction coefficient. In contrast, a linear increase of the magne-tostriction coefficient with applied stress is observed for Fe-Ni- rich microwires with positive magnetostriction coefficient. Observed results are discussed in terms of influence of internal stresses and short range atomic rearrangements induced by annealing on hysteresis loops, magnetostriction coefficients and Curie temperatures of studied microwires.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

A model to rationalize the effects of test temperature and microstructural variables on the creep crack growth (CCG) and creep-fatigue crack growth (CFCG) rates in ferritic steels is described. The model predicts that as the average spacing between grain boundary particles that initiate creep cavities decrease, the CCG and CFCG rates increase. Further, CCG data at several temperatures collapse into a single trend when a temperature compensated CCG rate derived from the model is used. CCG and CFCG behavior measured at different temperatures is used to assess the effects of variables such as differences between basemetal (BM), weldmetal (WM) and the heat-affected zone (HAZ) regions. The model is demonstrated for Grade 22 and Grade 91 steels using data from literature. It is shown that differences between the CCG behavior of Grade 22 steel in new and ex-service conditions are negligible in the BM and WM regions but not in the HAZ region. The CCG behavior of Grade 91 steels can be separated into creep-ductile and creep-brittle regions. The creep-brittle tendency is linked to the presence of excess trace element concentrations in the material chemistry. Significant differences found in the CCG rates between BM and the WM and HAZ regions of Grade 91 steel were explained.

With the development of bioinspired green solutions for sustainable construction over the past two decades, bio-cementation, which exploits the naturally occurring phenomenon of calcium carbonate precipitation in different environments, has drawn a lot of attention in both building construction and soil stabilization. Various types of microorganisms, along with specific enzymes derived from these microorganisms, have been utilized to harness the benefits of bio-cementation. Different application methods for incorporating this mechanism into the production process of the construction material, as well as a variety of experimental techniques for characterizing the outcomes of bio-cementation, have been developed and tested. Despite the success of bio-cementation as a sustainable method to construction has been demonstrated in a significant body of literature at the laboratory scale, the expansion of this strategy to construction sites and field application remains a pending subject. The issue may be attributed to two primary challenges. Firstly, the complexity of the bio-cementation phenomenon is influenced by a variety of factors. Secondly, the extensive body of literature examines various types of microorganisms under different conditions, leading to a wide range of outcomes. Hence, this study aims to examine the recent advancements in utilizing the most commonly employed microorganism, Sporosarcina Pasteurii, to emphasize the significance of influential factors identified in the literature, discuss the findings that have been brought to light, and outline future research directions toward scaling up the process.

This paper reports aligned activities to promote energy and resource-efficient construction practice in Vietnam. First, the governance framework is introduced, including government decrees and technical standards. Then, a laboratory with building physics measurement technology is designed and partly set up at the local partner Vietnam Institute for Building Materials (VIBM), which can be used to determine the essential characteristic values required for the implementation of energy standards. The basis for the prioritization of the characteristic values are the requirements of the National technical regulation on energy efficient buildings of Vietnam – QCVN09:2017/BXD. Furthermore, basic characteristic values from international standards are described, which can also be used for calculations to optimize the energy consumption of buildings. In order to be able to carry out transient hygrothermal computer simulations, special characteristic values were also included. These are particularly useful for the research and development of new building materials and the evaluation of entire buildings in terms of thermal and moisture protection In order to communicate the material properties to the market and enable informed decision making by the stakeholders, a labeling system has been developed. Thereby, the practical means for implementing governance instruments are provided, and the related technical applications are supported.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

Developing low-cost and stable materials for converting solar energy into electricity is vital in meeting the world's energy demand. Metal-organic frameworks (MOFs) have gained attention for solar cells due to their natural porous architectures and tunable chemical structures. This review commences with an exploration of the synthetic methods of MOFs. Moreover, we discuss the various roles of MOFs, including photoanodes and counter electrodes in dye-sensitized solar cells and interfacial layers and charge carriers in perovskite solar cells. Ultimately, burdensome tasks and possible directions for advancing MOFs-based nanomaterials are provided for solar cells.

The effect of organic matter (OM) on soil P-sorption is controversial and needs to be more investigated. The dissolved organic matter (DOM) may be regarded as an influential component on P sorption in natural soils. However, despite the great need for renewable sources of available P and OM in agricultural soils, little is known about interaction between P and DOM in natural soil systems. To uncover if and how soil saturation with DOM derived from different types of abundant agricultural wastes (cattle manure, horse manure, biogas digestate, compost) affects the phosphate sorption, we examined P sorption process in control and DOM-saturated sandy soils. The results indicated that organic matter introduced with agricultural wastes did not always reduce P sorption, but certainly had an effect on impairing P fixation and thus may result in potentially greater P mobility in the soil, including P availability. Up to now, we cannot recommend any of the tested organic amendments to directly overcome the P fixation in arable soils.

In this study, we presented a simple highly sensitive sensor based on commercially available solid core photonic crystal fiber (PCF) and surface plasmon resonance (SPR) for measuring the refractive index (RI) of analytes. The numerical simulation based on the finite element method (FEM) has been examined to compute the optical properties such as confinement loss, power spectrum, and transmission intensity of the sensor. The most sensitive and inert plasmonic materials (gold and silver) have been assumed to be coated inside the fiber with the range of analytes RI from 1.32 to 1.40. The performance of the proposed sensor has been evaluated by tracing the several optical features like wavelength sensitivity, amplitude sensitivity, resolution of the sensor, and figure of merit. As a result, the comparative study between silver and gold elements has been carried out in which the maximum sensitivity received as 1.15 μm/RIU and 1.10 μm/RIU respectively. Whereas, on the base of power spectrum the obtained sensitivity was 513 μm/RIU for the gold layer. Moreover, the effect of other structural parameters (air holes and plasmonic layers thickness) on the sensing performance has been taken into an account. According to the simulation analysis and results, this sensor would have a great potential in various sensing applications of biomedical and liquid refractive index.

Over the past few years, there has been an increasing fascination with electric unmanned aerial vehicles (UAVs) because of their capacity to undertake demanding and perilous missions, while also delivering advantages in terms of flexibility, safety, and expenses. These UAVs are revolutionizing various public services, encompassing real-time surveillance, search and rescue operations, wildlife assessments, delivery services, wireless connectivity, and precise farming. To enhance their efficiency and duration, UAVs typically employ a hybrid power system. This system integrates diverse energy sources, such as fuel cells, batteries, solar cells, and supercapacitors. The selection of an appropriate hybrid power arrangement and the implementation of an effective energy management system are crucial for the successful functioning of advanced UAVs. This article specifically concentrates on UAV platforms powered by batteries, incorporating innovative technologies like in-flight recharging via laser beams and tethering. It provides an all-encompassing and evaluative examination of the current cutting-edge power supply configurations, with the objective of identifying deficiencies, presenting perspectives, and offering recommendations for future consideration in this domain.

Geothermal energy is a weather-independent, permanently available renewable energy source. In addition to producing heat and electricity, geothermal energy can be used to extract critical raw materials dissolved in the heat-carrying fluid. Researchers working on the frontiers of geothermal energy utilisation may be able to transform ultra-deep metallic mineral formations into “orebody-Enhanced Geothermal Systems”. In the planned technology, the metal-containing geological formation would be manipulated in such a way that cogeneration of energy and metals is possible and can be optimised in the future according to market needs. The potential of geothermal energy for sustainable mineral extraction and energy production aligns with Sustainable Development Goal (SDG) 7, which aims to ensure access to affordable, reliable, sustainable, and modern energy for all. This new technology could substantially decrease Europe’s dependency on importing critical metallic minerals (such as lithium and tungsten) and energy; over and above, it has a small environmental footprint, including very low carbon emissions

Interference fits are a very common shaft-hub connection due to their low manufacturing cost and excellent technical properties. Plastic Conditioning of this machine element is a new and not very well known method. By exploiting residual stresses and the associated increase in the yield point, these components can absorb operating loads such as rotating bending moments, torsion, temperature changes and centrifugal forces purely elastically and avoid plastic deformation during operation. Compared to conventionally joined interference fits, the load bearing capacity in the elastic range can be increased by almost 200% and a specifically defined additional safety against plastic deformation in the elastic-plastic range can be ensured. This paper examines the effects of Reverse Yielding on the technology of Plastic Conditioning of Interference Fits in Power Transmission Engineering. Based on the Shear Stress Hypothesis (SH), the Plane Stress State (PSS) and the ideal plastic behavior of materials, the stress-mechanical relationships are explained, the influencing parameters are examined and conclusions are drawn for the plastic conditioning process. Taking into account the theoretical knowledge according to the state of the art, modified material behavior assumptions (isotropic hardening) and the Von Mises Yield Criterion (VMYC) are also considered. In addition, the method of plastic conditioning of interference fits is introduced and its basic principles are briefly explained. Along with computational suggestions to avoid Reverse Yielding, open issues requiring further research are identified.

In the contemporary era, there has been a notable surge in the systematic utilization of therapeutic drugs that exhibit stimulus-responsive drug release patterns in specific target areas. However, challenges such as premature drug release and limited biocompatibility persist. To address these issues, the application of a lipid coating on mesoporous silica nanoparticles (MSNs) has emerged as a promising strategy. This lipid coating not only enhances the stability and biocompatibility of nanocarriers but also facilitates targeted drug delivery to diseased cells while minimizing drug release throughout the body. MSNs, renowned for their unique attributes including high porosity, morphology, and controllable pore size, have been widely recognized as suitable platforms for drug/gene delivery systems. Furthermore, graphene-based nanomaterials such as graphene oxide and reduced graphene oxide have garnered significant interest in the fields of biology and biomedicine. These materials possess exceptional characteristics such as a large surface area, distinct surface properties, high biocompatibility, and pH sensitivity, making them ideal candidates for incorporating drugs, genes, photosensitizers, and other cargo to design innovative drug delivery systems. This study aims to emphasize the ongoing efforts and advancements in enhancing the capacity and versatility of nanocomposites comprising graphene MSN composites for applications in drug delivery.

As a rapidly expanding family of two-dimensional (2D) materials, MXenes have recently gained considerable attention due to their appealing properties. Here, by developing a solution-based coating method that enables transfer-free and layer-by-layer film coating, we investigate the layer-dependent nonlinear optical absorption of Ti₃C₂T_x films ‒ an important member of the MXene family. By using the Z-scan technique, we characterize the nonlinear absorption of the prepared MXene films consisting of different numbers of monolayers. The results show that there is a strong and layer-dependent nonlinear absorption behavior, transitioning from revisable saturable absorption (RSA) to saturable absorption (SA) as the layer number increases from 5 to 30. Notably, the nonlinear absorption coefficient β varies significantly within this range, changing from ~7.13 × 10² cm/GW to ~-2.69 × 10² cm/GW. We also characterize the power-dependent nonlinear absorption of the MXene films at various incident laser intensities, and a decreasing trend in β is observed for increasing laser intensity. These results reveal the intriguing layer-dependent nonlinear optical properties of 2D MXene films, highlighting their versatility and potential for implementing high-performance nonlinear photonic devices.

Authentic learning opportunities that simulate full scale design and construction experiences using real materials offer ideal experiential learning environments for construction and civil engineering students by challenging students to apply building concepts in practical settings. However, the excessive cost of real building materials required for this mode of education limits access to the vast majority of students. As a result, educational researchers have explored potential alternatives to provide cost-effective experiential learning through activities using mock-up materials (e.g., plastic straws, popsicle sticks) and simulation of experiences using immersive technologies (e.g., virtual reality or augmented reality). While some of these alternatives approximate the environment and others provide physical interaction with mock-up materials, the lack of authenticity in the building materials used introduces some apparent differences between the “authentic” learning environments and their cost-effective approximations. Therefore, this research aims to identify the learning processes reported by students and faculty who participated in authentic learning experiences to understand the ways in which this mode of education offers unique value to construction education. Their interview responses illustrated characteristics of authentic learning experiences that were believed to be critical to the learning process, some of which included: working in groups; interdisciplinary participants; and use of real construction materials. Although some of these characteristics are intrinsically linked to the use of real materials, others do not explicitly refer to interaction with real materials. This may indicate to aspects of the authentic learning processes that educational researchers can strategically target through more cost-effective learning environments like virtual and augmented reality. The contribution of this paper is in identifying the characteristics of authentic learning experiences that may guide educational investment and research innovations that aim to replicate some of these learning experiences through more accessible learning environments.

The cutting of difficult-to-machine materials, including their preconditioning, often requires specialised tools and machinery. An alternative processing technology can be cutting materials with a water jet. From the initial stage, the selection of appropriate technological parameters will influence what further finishing treatments will be applied. Vibrations occurring during this process can negatively affect the quality of the cutting edges and surfaces. Therefore, this study analysed vibrations during water-jet cutting with variable technological parameters (speed vfi and pressure pi). To measure the vibrations, a three-axis accelerometer from SEQUOIA was used in water-jet cutting of three materials: aluminum alloy, titanium alloy, and steel. Based on the study, it was found that the maximum value of vibration amplitude reaches the lowest value of vibration acceleration for aluminum alloy (not exceeding 5 m/s2), regardless of the value of pressure during the cutting process. This, taking into account the material properties, indicates that aluminum alloy is the material most susceptible to the cutting process while maintaining a high quality of the cutting surface. Significantly higher values of vibration acceleration amplitude (reaching up to 60 m/s2) during cutting were registered for steel and titanium alloy in all zones and phases of the process (entry zone, cutting zone, and exit zones).

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

In this research, the application of the Physics-Informed Neural Network (PINN) model is explored to solve transport equation-based Partial Differential Equations (PDEs). The primary objective is to analyze the impact of different activation functions incorporated within the PINN model on its predictive performance, specifically assessing the Mean Squared Error (MSE) and Mean Absolute Error (MAE). The dataset used in the study consists of a varied set of input parameters related to strut diameter, unit cell size, and the corresponding yield stress values. Through this investigation, the aim is to understand the effectiveness of the PINN model and the significance of choosing appropriate activation functions for solving complex PDEs in real-world applications. The outcomes suggest that the choice of activation function may have minimal influence on the model's predictive accuracy for this particular problem. The PINN model showcases exceptional generalization capabilities, indicating its capacity to avoid overfitting with the provided dataset. The research underscores the importance of striking a balance between performance and computational efficiency while selecting an activation function for specific real-world applications. These valuable findings contribute to advancing the understanding and potential adoption of PINN as an effective tool for solving challenging PDEs in diverse scientific and engineering domains.

Even though, graphene family materials (GFMs) hold great promise for various applications, there are still significant knowledge gaps in ecotoxicology and environmental risk assessment associated with their potential environmental impacts. Here, we provide a critical perspective on published ecotoxicity studies of GFMs based on a meticulous bibliometric research. Analysis of the available data revealed that to date, ecotoxicity studies with GFMs have been carried out predominantly using freshwater species (82%), while their effects on marine or terrestrial or-ganisms are understudied. Three groups of organisms were found dominating ecotoxicological research: fish (39%), algae (20%) and arthropoda (20%) predominantly applying small, planktonic crustaceans. It was also revealed that despite their widespread detection in different environ-mental compartments the potential impacts of GFMs in complex test systems with hierarchical trophic organisation or in trophic transfer studies are significantly under-represented. One of the main causes was identified as the difficulties in the physicochemical characterisation of GFMs in complex terrestrial test systems or in aquatic micro- and mesocosm studies containing a sediment phase. The lack of tools for adequate characterisation of GFMs in these complex test systems may discourage researchers from conducting experiments under environmentally relevant test condi-tions. However, in the coming years, fundamental research about these complex test systems will con-tinue to better understand the mechanism behind GFMs toxicity affecting organisms in different environmental compartments and to ensure their safe and sustainable use in the future.

Concrete is the most utilized construction material worldwide. In the marine environment, it is subject to chemical degradation through reactions with chloride (the most important ion), sulfate and magnesium ions in seawater and to biodeterioration resulting from biological (initially microbiological) activities, principally acid production. These two types of corrosion are reviewed and the failure of attempts to predict the degree of deterioration resulting from each is noted. Chemical (abiotic) corrosion is greatest in the splash zone of coastal constructions, while phenomenological evidence suggests that biodeterioration is greatest in tidal zones. There have been no comparative experiments to determine the rates and types of microbial biofilm formation in these zones. Both chemical and microbiological concrete deterioration are complex and have not been successfully modeled. The interaction between abiotic corrosion and biofilm formation is considered. EPS can maintain surface hydration, potentially reducing abiotic corrosion. The early marine biofilm contains relatively specific bacterial colonizers, including cyanobacteria and proteobacteria; these change over time, producing a generic concrete biofilm, but adhesion of microorganisms to concrete in the oceans is little investigated. The colonization of artificial reefs is briefly discussed. Concrete appears to be a relatively prescriptive substrate, with modifications necessary to increase colonization for the required goal of increasing biological diversity.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

Information encryption and anti-counterfeiting play an important role in many aspects of daily life, such as in minimizing economic losses, protecting secure communication and public security, and so on. Owing to the high information capacity and ease of operation, luminescent materials for advanced information encryption and anti-counterfeiting are essential to meet the increasing demand on encryption security. Herein, we summarize two emerging luminescent materials for information encryption and anti-counterfeiting, the AIE materials and room-temperature phosphorescent materials. At last, we discuss the opportunities and anticipations of these two information encryption and anti-counterfeiting materials.

Bisphenol A is a remarkable chemical compound for its many applications mainly in the plastics industry, but also for its toxic effects on the environment and human health. BPA (4,4-isopropylidenediphenol) is an anthropogenic compound, moderately soluble in water (120 – 300 mg/l) at room temperature, and highly soluble in alkaline solutions, ethanol and acetone. BPA can bioconcentrate, bioaccumulate and biomagnify through food webs until it reaches humans. To prevent this, effective strategies are sought to allow its removal from the environment, through physico-chemical or enzymatic methods, advanced oxidation, adsorption and biodegradation, ultrasonic degradation. This article shows a comparative study regarding adsorption of BPA on Active carbon and zeolitic tuff, ZTC. In this paper, the characterization of the zeolitic tuff Rupea adsorbent, was carried out from an elemental and mineralogical point of view, pore size and elemental distribution, using SEM, EDAX, and XRD analysis. The pore size varies from 30 nm to 10 µm, atomic ratio Si/Al≥4, and the 80 % of mineralogical composition represent Ca Clinoptilolite zeolites Ca Clinoptilolite zeolite ((Na1.32K1.28Ca1.72Mg0.52)(Al6.77Si29.23O72)(H2O)26.84). Also, a comparative study of the adsorbtion capacity of bisphenol A from synthetic solutions on activated carbon type - Norit GAC 830 W, GAC, as well as on Clinoptilolite-type zeolitic tuff, ZTC, Rupea, was carried out. The experiments were carried out at a temperature of 20 ºC, a pH of 4.11; 6.98 and 8.12, and ionic strength being assured using KCl of 0.01 M, and 0.1 M. The adsorption capacities of GAC and ZTC tend to 115 mg/g and 50 mg/g respectively, at 8.12 pH and ionic strength of 0 M. The Langmuir mathematical model most faithfully describes the adsorption equilibrium of BPA. The maximum adsorption capacity for both adsorbents increases with increasing pH, and decreases with increasing ionic strength.

In response to growing environmental concerns and the need for sustainable resources, researchers worldwide are examining how to develop materials that are environmentally friendly and that can be effectively recycled as they reach the end of their useful life. Particularly interesting are polyurethanes (PUs), a broad class of synthetic polymers utilized in several applications. However, because of the high energy consumption and unwanted chemical side reactions, their chemical recycling is challenging. A possible method for recovering PU is biological recycling, which breaks down complex compounds using microbes and enzymes. The biodegradation susceptibility of novel PUs using tree bark extractives as building blocks is examined in this work. The PUs were synthesized with partial or complete substitution of conventional fossil-based polyol (PEG 400) with hydrophilic extractives from black alder bark. Biodegradation experiments in sewage water and compost-enriched soil were conducted over 60 days. Results indicate increased biodegradation in PUs containing bark-based polyols, showing weight losses of up to 15.7% and 15.6% in sewage water and soil, respectively, compared to 9.6% and 12.4% for fossil-based PU. Analytical pyrolysis and FTIR analysis revealed more significant structural changes in extractives-containing PU materials after biodegradation compared to fossil-based PU, indicating the cleavage of covalent bonds mainly in carbohydrate and aromatic constituents of biopolyol. But the urethane bonds revealed the highest stability towards biodegradation compared to others linkages in both fossil-based and bio-based PU. The study demonstrates the potential of using bark-derived polyols to design PU materials suitable for biological recycling, contributing to more environmentally friendly waste management strategies. Further investigations are needed to optimize the conditions for the biological conversion of PU materials synthesized with bark-based polyols.

Hydrogen is believed to be the principal domain of sustainable energy drive as an alternative to fossil fuels. Unlike the existing standards and knowledge for other fuels, the integrity of sealing and storage materials under the hydrogen environment is not comprehensively studied due to the comparatively new technology and lack of standard laboratory protocols. Typically, storage and polymer materials used as sealing experience degradation and damage in different ways over time in the exposure of hydrogen at different operating conditions, called aging. Improved understanding of the physical and chemical mechanism of degradation due to gaseous hydrogen atmosphere; helps to select and develop the materials best suited to carrier and sealing for respective applications. Damage to materials from aging is inevitable in high-pressure hydrogen gas exposure. This review discusses the mechanism of different categories of aging of storage and sealing materials under the hydrogen environment. Also, the article approaches discussing different laboratory test methods for each type of aging simulation. It covers the limitation of current research on determining material integrity through existing techniques of aging experiments and also explores the latest development. Important improvements are suggested in terms of materials development and testing procedures to meet the existing knowledge in the literature.

One of the most burning topics in cybersecurity in 2023 will undoubtedly be the compliance with the Software Bill of Materials. Since the US president issued the Executive Order 14028 on Improving the Nation’s Cybersecurity, software developers have prepared and bills are transmitted to vendors, customers, and users, but they don’t know what to do with the reports they are getting. In addition, since software developers have identified the values of the Software Bill of Materials, they have been using the reports extensively. This article presents an estimate of 270 million requests per month, just from form one popular tool to one vulnerability index. This number is expected to double every year and a half. This simple estimate explains the urgency for automating the process. We propose solutions based on artificial intelligence and machine learning, and we base our tools on the existing FAIR principles (Findable, Accessible, Interoperable, and Reusable). This methodology is supported with a case study research and Grounded theory, for categorising data into axis, and for verifying the values of the tools with experts in the field. We showcase how to create, and share Vulnerability Exploitability eXchange data, and automate the Software Bill of Materials compliance process with AI models and a unified computational framework combining solutions for the following problems: (1) the data utilisation problem, (2) the automation and scaling problem, (3) the naming problem, (4) the alignment problem, (5) the pedigree, and provenance problem, and many other problems that are on the top of mind for many security engineers at present. The uptake of these findings will depend on collaborations with government and industry, and on the availability and the ease of use of automated tools.

Clinical outcomes of dental restorations depends primarily on the choice of materials used and their fabrication processes. The spectrum of dental CAD-CAM (Computer-Aided Design Computer-Aided Manufacturing) materials presents a wide range of variables on what may be the most suitable material for the clinical case. This narrative review focuses on CAD-CAM dental materials based on their mechanical properties and in relation to their clinical applications. A literature review was performed on PubMed, Scopus, Web of Knowledge, and Cochrane Library. Articles addressing at least one of the following topics regarding dental materials for CAD-CAM systems: manufacturers, mechanical features, materials ’composition optical properties, clinical indications and / or outcomes were included in the review. A flowchart was performed as de-scribed in the PRISMA guidelines. Among the 564 articles found, 63 were analyzed and evaluated. Within the limitation of this narrative review, it can be concluded that all CAD-CAM materials presents a wide range of clinical applications due to their improved mechanical properties. Specifically, in addition to materials that have been in use for a long time (such as feldspathic ceramics), resin block composites can also be used for permanent restorations.

Reconfigurable chiral metasurfaces with dynamic polarization manipulation capability are highly required in optical integrated systems. In this paper, we simultaneously realized giant and large-range switchable asymmetric transmission (AT) and circular conversion dichroism (CCD) in a vanadium dioxide (VO2) based metasurface. The AT and CCD of the insulator VO2 based metasurface reach 0.95 and 0.92, respectively. Utilizing the insulator-to-metallic phase transition of VO2, the AT and CCD could be continuously switched to near zero. Furthermore, the physics mechanism of the giant and switchable AT and CCD are analyzed. The proposed metasurface with large-range switchable AT and CCD is promising in the applications of biochemistry detection, chiral imaging and biosensing.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.

Iron oxide nanoparticles have been investigated due to their suitable characteristics for diverse applications in the fields of biomedicine, electronics, water/wastewater treatment and sensors. Maghemite, magnetite and hematite are the most widely studied iron oxide particles and have ferrimagnetic characteristics. When very small, however, these particles have superparamagnetic properties and are called superparamagnetic iron oxide nanoparticles (SPIONs). Several methods are used for the production of these particles, such as coprecipitation, thermal decomposition and microemulsion. However, the variables of the different types of synthesis must be assessed to achieve greater control over the particles produced. In some studies, it is possible to compare the influence of variations in the factors for production with each of these methods. Thus, researchers use different adaptations of synthesis based on each objective and type of application. With coprecipitation, it is possible to obtain smaller, more uniform particles with adjustments in temperature, pH and the types of reagents used in the process. With thermal decomposition, greater control is needed over time, temperature as well as the proportion of surfactants and organic and aqueous phases in order to produce smaller particles and a narrower size distribution. With the microemulsion process, the control of the confinement of the micelles formed during synthesis through the proportions of surfactant and oil makes the final particles smaller and less dispersed. These nanoparticles can be used as additives for the creation of new materials, such as magnetic bacterial cellulose, which has different innovative applications. Composites that have SPIONs, which are produced with greater rigour with regards to size and distribution, have superparamagnetic properties and can be used in medical applications, whereas materials containing larger particles have ferromagnetic applications. To arrive at a particular particle with specific characteristics, researchers must be attentive to both the mechanism selected and the production variables to ensure greater quality and control of the materials produced.

Total Hip Arthroplasty (THA) is a common surgical procedure used to treat hip osteoar-thritis and other joint conditions that cause pain and functional limitation. Traditionally, THA has been most performed in elderly patients, but in recent years there has been an in-crease in hip arthroplasties in young patients. Femoral prosthesis rupture is a rare but sig-nificant complication that can also occur in young patients undergoing total hip arthro-plasty (THA). Some of the factors that can contribute to femoral prosthesis ruptures include abnormal overload, defects in the design lack of geometric fit, type of materials used in the stem and femoral head connection. The aim of this study is to analyze the criticalities in the contact between the femoral head and the stem neck. In particular, the two types of con-tacts will be taken into consideration: proximal and distal and through the finite element method (FEA) the criticalities will be defined. The results show that in the proximal contact the voltages are higher than 500 Mpa. This is due to the fact that there are higher circum-ferential voltages. In addition, to prevent bacterial infiltration or debris from the outside, the distal connection is the recommended one.

Increasing photon absorption by capturing light is an important way to increase the efficiency of photovoltaic devices. In this regard, the small optical band gap (Eg) and high absorption coefficient of Se-containing thin nanofilms make them ideal for next generation photovoltaic devices based on selenides. This study reports on chemical synthesis processes in a bath for the insertion of amorphous selenium into polyamide-6 (PA 6) matrix and the effect of incorporation of Cd2+ and Ag+ on the structural, morphological and optical properties. The resulting films had a pyramidal structure of single crystals, nanosized particles of nonspecific shape, agglomerated and indistinct grains. ATR-FTIR spectroscopy revealed the interaction between PA 6 and inorganic components, which causes obvious conformational changes in PA 6 chains. The data of X-ray diffraction analysis, depending on the stage of synthesis, showed a mixture of various compounds: Se8, CdSe, Ag2Se and Ag. This may explain the observed optical properties. The optical properties of the composites indicate a shift in the band gap from 4.46 eV for PA 6 to 2.23-1.64 eV upon stepwise insertion of amorphous Se, Cd2+ and Ag+ ions. Eg is conveniently located in the visible region of solar energy, making the obtained nanofilms ideal for solar energy harvesting.

A novel electrophoretic technique to improve the sensing capabilities of charged particles in solution is presented. The proposed technique may improve the ability of metasurfaces to sense charged particles in solution by forcing them to preferentially sediment within metasurface regions of greatest sensitivity. Such a technique may be useful in various sensing applications, such as in biological, polymer, or environmental sciences, where low concentration particles in solution are of interest. The electrophoretic technique was simulated and experimentally tested using latex nanoparticles in solution. The results suggest that, using this technique, one may theoretically increase the particle density within the metasurface regions of greatest sensitivity by nearly 1900% in comparison to random sedimentation due to evaporation. Such an increase in particle density within the regions of greatest sensitivity may facilitate more precise material property measurements and enhance identification and detection capabilities of metasurfaces to low concentration particles in solution. It was experimentally verified that the electrophoretic technique enabled the preferential gathering of latex nanoparticles within the most sensitive metasurface regions, resulting in 900% - 1700% enhancements in metasurface sensing capabilities.

Material selection for product design is a complex task. Thus, one of the objectives of this work is to analyze, understand and promote the importance of selection of materials to conceive quality products with help of designers' that promote green self-identity in the early stage of the conception of new products. A questionnaire was sent to professional designers and engineers. 38 responses were validated, this being the sample of our study. The aspects that influence the complex selection of materials and the final quality of the products through the design and production process is presented. As a result of the answers carried out with product designers who work in the market, with students who are graduating and with some engineers, a new approach for the selection of materials was developed. Based on a collection of main ideas from traditional and non-traditional methods of material selection, seeking to group the maximum requirements of both methods, inspired by the "Canvas" model on the basic modular methodology, a new model for a project of new product is presented. Our study focuses on the selection of materials, since this aspect is one of the most relevant steps in early stage of the prototyping phase of new products, with a view to reducing CO² from the air in the atmosphere that we all breathe. The classification of materials is complex, due to the diversity of available options. The novelty of this model is that all properties of the newly designed product, such as technical, aesthetic, productive, environmental and other properties, are all grouped in a model, which serves as an innovative support. Thus, the designer has at his disposal a tool that can help him in the selection of the best material for the products he designs. This study intends to make a contribution in the field of material selection, quality and design of new products, promoting a green self-identity for designers in the initial phase of product design. Consequently, all consumers in search of a sustainable planet will profit from it.

In this work, a simple and environmentally friendly process combining low pressure (vacuum) and mechanical compression is proposed to convert recycled polypropylene (PP) foams (28 kg/m3) into low density foams (90-131 kg/m3) having negative tensile and compressive Poisson's ratios (NPR). The effect of processing conditions (vacuum time, temperature, and mechanical pressure) was studied. Based on the optimized conditions, the tensile Poisson’s ratio of the resulting auxetic foams reached −1.50, while the minimum compressive Poisson's ratios was −0.32 for the same sample. The foam structure was characterized via morphological analysis (SEM) to determine any changes related to the treatment applied. Finally, tensile and compressive properties (Young's modulus, strain energy, energy dissipation and damping capacity) are also presented and discussed. It was observed that the mechanical properties of the resulting auxetic foams were improved compared to the original PP foam (PP-O) for all tensile properties in terms of modulus (19.9 to 59.8 kPa), strength (0.298 to 1.43 kPa) elongation at break (28 to 77%), energy dissipation (14.4 to 56.3 mJ/cm3) and damping capacity (12 to 19%). Nevertheless, improvements were also observed under compression in terms of energy dissipation (1.6 to 3.6 mJ/cm3) and damping capacity (13 to 19%). These auxetic foams can find applications in sport and military protective equipment, as well as any energy mitigation system.

Acoustic metasurface are artificial structures which could manipulate the wavefront in sub-wavelength dimensions and the previous proposed acoustic metasurface were mostly realized with single materials. An acoustic metasurface with composite structure is proposed for underwater acoustic stealth considering both wavefront manipulation and sound absorption. The unit cells of the metasurface are composed by metallic supporting lattice, interconnecting polymer materials and mass balancing columns. With the gradual modulations of equivalent physical properties along the horizontal direction of metasurface, the incident acoustic wave is reflected to other directions. Meanwhile, the polymer material inside the unit cells would dissipate the acoustic wave energy due to inherent damping properties. With the simultaneous modulations of reflected wave direction and scattering acoustic amplitude, significant improvement of underwater stealth effect is achieved. Compared with single-phase metasurface, the Far-Field Sound Pressure Level (FFSPL) of the multiphase metasurface decreased by 4.82 dB within the frequency range of 3kHz~30kHz. Under a hydrostatic pressure of 5MPa, the linearized mean stress for multiphase metasurface is only 1/3 of that of single-phase metasurface due to much thicker struts and much more uniform stress distribution. The proposed composite structure possesses potential applications due to acceptable thickness (80mm) and low equivalent density (1100 kg/m3).

Rising raw material prices can have a significant impact on the financial performance of the food and beverage (F&B) business. The purpose of this study was to determine the impact of rising prices of staples onfinancial resilience F&B business in Indonesia. This study uses a quantitative approach with bivariate correlation analysis and secondary data from the financial reports of F&B companies listed on the Indonesia Stock Exchange for the 2020-2022 period. The results showed that the increase in the price of basic commodities had a significant positive impact onfinancial resilience F&B company. This can be seen from the decline in the profitability and liquidity of F&B companies as a result of the increase in the price of basic commodities. Therefore, F&B companies must pay attention to and manage the risk of rising prices of basic commodities to maintainfinancial resilience and sustainable business continuity.

Neuromorphic computing, reconfigurable optical metamaterials operational over a wide spectral range, holographic and nonvolatile displays of extremely high resolution, integrated smart photonics and many other applications need phase-change materials (PCMs) of the next generation with better energy efficiency, wider temperature and spectral range for reliable operation compared to current flagship PCMs as Ge2Sb2Te5 or doped Sb2Te. Gallium tellurides are promising candidates to achieve the necessary requirements because of higher melting and crystallization temperatures, combined with a low switching power and fast switching rate. At the same time, Ga2Te3 and non-stoichiometric alloys appear to be atypical PCMs, characterized by regular tetrahedral structure and the absence of metavalent bonding. The sp3 gallium hybridization in cubic and amorphous Ga2Te3 is also different from conventional p-bonding in flagship PCMs, raising a question of the phase-change mechanism. Besides, gallium tellurides exhibit a number of unexpected and highly unusual phenomena as nanotectonic compression or viscosity anomaly just above melting. Using high-energy X-ray diffraction, supported by first-principles simulations, we will unravel the atomic structure of amorphous Ga2Te5 PLD films, compare it with the crystal structure of tetragonal gallium pentatelluride, and investigate electrical, optical and thermal properties of these two materials to estimate their potential for memory applications as well as for other fields.

Highly efficient, broadband and distinctively structured electromagnetic wave (EMW) absorption materials exhibit huge exceptions with multi-functions in both military and civilian fields. Searching the relationship between structural and EMW performance is beneficial to develop outstanding microwave absorption materials, and has become an attractive research topic. In this study, we briefly reviewed the different EMW absorption mechanisms and key influence factors, then, present the latest developments in low-dimensional (LD) EMW absorption materials. We provide a comprehensive discussion of remarkable examples and summarize the main information related to the structure-function relationship of dimensional design and structural engineering in order to facilitate the rapid evolution of this fascinating field.

Polymeric hydrogels are promising polymeric functional materials that have been widely used in the biomedical field as an emerging carrier of various therapeutic agents. Polymeric hydrogels as a carrier of therapeutics can leverage therapeutically beneficial outcomes of drug delivery than systemic chemotherapy and can provide spatial and temporal control over the release of various therapeutic agents. Polymeric hydrogels are cross-linked three-dimensional networks constructed by hydrophilic polymers and they are capable of absorbing and re-taining a large amount of water. Polymeric hydrogels share many physiochemical features with natural tissues due to their water abundance, biomimetic microstructure, and intrinsic flexibility. Polymeric hydrogels have excellent biocompatibility, biodegradability, and lower toxicity. Polymeric hydrogels enhance the convenience and efficiency of drug delivery by assisting in situ gelation and controlling drug release by changing their volume and other properties when it encounters some stimuli (e.g., heat, pH, light, and ultrasound). This review aims to outline the overview of polymeric hydrogels, properties, types, advantage, disadvantages, characteri-zation, and their application with present status and future perspective used for the delivery of therapeutics in pharmaceutical and biomedical sciences.

: Medical gloves, along with masks and gowns, serve as the initial line of defense against poten-tially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized by society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infec-tion-prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most usual gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber gloves manufacturing process and mitigation strate-gies, such as bioremediation and rubber recycling, are addressed. In order to create new smart medical gloves with improved properties, several biopolymers (e.g. poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g. silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these smart materials and describes different innovative prototypes of gloves and coatings designed with them.

Using valid experimental parameters we quantify the magnitude of resonantly phonon-driven precession of exchange magnons in freestanding ferromagnetic nickel thin films on their thickness L. Analytical solutions of acoustically driven equations for magnon oscillators display a nonmonotonous dependence of the peak magnetization precession on the film thickness. It is explained by different L-dependence of multiple prefactors entering in the expression for the total magnetization dynamics. Depending on the ratio of acoustic and magnetic (Gilbert) damping constants, the magnetization precession is shown to be amplified by a Q-factor of either the phonon or the magnon resonance. The increase of the phonon mode amplitude for thinner membranes is also found to be significant. Focusing on the magnetization dynamics excited by the two first acoustic eigenmodes with p=1 and p=2 we predict the optimum thicknesses of nickel membranes to achieve large amplitude magnetization precession at multi 100 GHz frequencies at reasonably low values of an external magnetic field.

There is an international concern for reducing energy consumption and protecting the environment in the construction industry. The energy efficiency of a building depends on the thermal resistance of concrete, and utilizing concrete products with elevated thermal resistance can enhance this aspect. This study analyzes the impact of perlite, as an addition, on the physico-mechanical properties of concrete, with the aim of identifying perlite concrete products that will respond to the improvement of the heat transfer resistance of the building envelope. The study examines the effect of replacing different amounts of concrete aggregates with perlite in percentages of 10%, 20%, 30%, and 100%. The results show that substituting sand with perlite improves the thermal performance of concrete, but its mechanical properties are negatively affected. The research carried out highlighted that perlite can be successfully introduced in the production of concrete blocks used for external non-bearing wall panels, the outstanding feature being the reduction of energy consumption in buildings. Overall, the paper identifies an efficient and environmentally friendly way of using perlite in the construction industry, enhancing the energy efficiency of buildings while minimizing the environmental footprint caused by the construction industry.

Perovskite solar cells are an evolving technology owing to self-assembling and highly tunable bandgap properties of materials. In this context, thin films of perovskites have attracted immense attention and witnessed great advancement because of their low manufacturing cost. The key development in these devices is the conversion efficiency, which rose from 3.8% to 28%. The formulation of innovative materials with the proper replacement of lead in perovskites is imperative to mitigate lead toxicity. Here, we analyzed the challenges like material and structural stability, device stability under high temperature and humidity conditions, lifetime, manufacturing cost, etc. faced in the commercialization of perovskite devices. This review shows that challenges such as device engineering, performance stability against the harsh environment, cost-effectiveness, and environmental concern should be taken into consideration for the widespread acceptance of perovskite-based solar devices. In conclusion, we suggested that an enormous scope exists for exploring high-performance and long-lasting perovskites for energy applications.

The broad acceptance of electromobility depends heavily on the performance and service life of the battery technology used. Lithium-ion battery technology is currently the most promising energy storage technology for mobile applications, but the performance and capacity of the cells is extremely temperature sensitive. Especially in these new complex and powerful applications there is a significant need for thermal management. Depending on the ambient conditions, part of the effective battery energy must therefore be used to temper the system. So far, mainly active components have been used for this task. This not only reduces the overall efficiency, but also increases the weight, volume and maintenance requirements of the system. In the present work, an alternative battery temperature management system (BTMS) was developed. A concept based on latent heat storage materials was created, which uses the advantages of thermal energy storage and the design freedom of additive manufacturing technology, and its suitability for use in battery applications was checked. On the one hand, the use of systems for storing thermal energy was researched and, on the other hand, an innovative cooling concept was created considering new production possibilities.

Several methods of processing wood into strong, durable products for the construction industry provide transformative opportunities to substitute for less sustainable building materials. Carbon storage is a further advantage, with the added possibility of combustion for bioenergy at end of life. Intense research activity in this area is expected to open up new markets for wood fiber during the lifetime of trees now being planted. Here, wood-derived materials are classified according to the particle size, from metres to nanometres, into which the wood is fragmented before reconstitution. Materials made by densifying or chemically modifying solid wood with no fragmentation are already in production for exterior doors, window frames and cladding, with improved uniformity and stability compared with unmodified wood. Pre-commercial developments promise further gains in durability and strength. Emerging developments extend these process technologies to wood that has been chipped or stranded or pulped, retaining the above advantages over raw timber for weather-facing applications and adding processability by moulding or extrusion. Crucially, the raw material does not then need to be sawn timber but can be bioenergy-grade wood biomass. This will facilitate afforestation strategies that combine the aims of carbon sequestration and biodiversity.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

The main purpose of tissue engineering is to fabricate and exploit engineered constructs suitable for the effective replacement of damaged tissues and organs, and able to perfectly integrate with the host’s organism without eliciting any adverse reaction. Ideally, autologous materials represent the best option, but they are often limited due to the low availability of compatible healthy tissues. So far, one therapeutic approach relies on the exploitation of synthetic materials: they exhibit good features in terms of impermeability, deformability and flexibility, but present chronic risks of infections and inflammations. Alternatively, biological materials, including naturally derived ones and acellular tissue matrices of human or animal origin, can be used to induce cells growth and differentiation, which are needed for tissue regeneration: however, this kind of materials lacks satisfactory mechanical resistance and reproducibility, affecting their clinical application. In order to overcome the above-mentioned limitations, hybrid materials, which can be obtained by coupling synthetic polymers and biological materials, have been investigated with the aim to improve biological compatibility and mechanical features. Currently, the interest in these mate-rials is growing, but the ideal ones have not been found yet. The present review aims at exploring some applications of hybrid materials, with particular mention to urological and cardiovascular fields: in the first case, the efforts to find a construct that can guarantee impermeability, mechanical resistance and patency will be herein illustrated; in the second case, the search for impermeability, hemocompatibility and adequate compliance will be been disclosed.

The injectable hydrated calcium phosphate bone-like paste (hCPP) have been developed with suitable nanoscale characteristics and unindered injection through 23G standard needles. In vitro assays showed the cytocompatibility of hCPP with mesenchymal embryonic C3H10T1/2 cell cultures. The hCPPs were identified to be composed of aggregated nano-sized particles with sphere-like shapes with low crystallinity. The ability of serum proteins (FBS) to adsorb on hCPP particles was also studied. The hCPP demonstrated high protein adsorption capacity, thereby indicating its potential in various biomedical applications. The results of the in vivo assay upon subcutaneous injection in Wistar rats indicated the nontoxicity and biocompatibility of experimental hCPP, as well as the gradual resorption of hCPP, comparable to the period of bone regeneration. The data obtained are of great interest for the development of commercial highly effective osteoplastic materials for bone tissue regeneration and augmentation.

The modern material design aims to achieve multifunctionality by integrating structures in a diverse range, resulting in simple materials with embedded functions. Biological materials and organisms are typical examples of this concept, where complex functionalities are achieved through a limited material base. This review highlights the inspiration from multifunctional organisms and materials in nature, emphasizing their structural and functional integration. In particular, we discuss complex hierarchical architectures ranging from the nanoscale to the macroscale, to achieve multifunctional properties such as extreme pressure, impact and wear resistance, shape memory and self-healing, adhesiveness and anti-fouling, sensing-actuating and sensing-camouflage, and extreme environmental survival. These strategies of integrating structure and function are critical for promoting innovations and breakthroughs in the modern engineering materials and applications.

The challenge of achieving ultrafast switching of electric polarization in ferroelectric materials remains unsolved, as there is no experimental evidence of such switching to date. In this study, we have developed an enhanced model that describes switching within a two-dimensional space of generalized coordinates. Our findings indicate that stable switching in barium titanate cannot be achieved through a single linearly polarized pulse. When the intensity of the linearly polarized pulse reaches a certain threshold, the sample experiences depolarization, but not stable switching. Our study also reveals that phonon friction plays a minor role in the switching dynamics and provides an estimate of the optimal parameters of the perturbing pulse with the lowest intensity that results in depolarization of an initially depolarized sample.

The luminescent properties of photocured aliphatic and aromatic network polycarbonate methacrylates containing organic fluorescent dyad have been studied. The dyad molecule includes two photosensitive fragments – tetraarylimidazole with a hydroxy group and azomethinocoumarin, in each of which excited state intramolecular proton transfer occurs, which leads to the appearance of two emissions - blue and green. It was established that the ratio of the intensities of these emissions depends on the excitation wavelength, as well as on the length, flexibility and polarity of the matrix oligomeric bridges.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

The global context of research for new sustainable energy storage technologies makes it a very active sector with significant scientific and economic challenges. Indeed, due to the irregular development of renewable energies and the shutdown of traditional power facilities, it is difficult to maintain a stable balance in terms of supply and demand: energy storage can help in particular for substantial changes in the latter. Metal air batteries have a higher energy density and are safer than other available energy storage devices. Based on the existing and proven lead-acid battery technology, this paper proposed an open cell foam manufactured by the Excess Salt Replication process for use as an anode for lead-air battery cellsies with sulphuric acid as the electrolyte. This will save lead and reduce the battery weight. A 25% antimonial lead alloy was used to produce open cell foams with a cell diameter between 2 mm and 5 mm for the antimonial lead-air battery. Preliminary results of the effective electrical conductivity of self-discharged primary battery cells, measured experimentally, showed that all antimonial lead foam-air battery cellsies performed better than that made from the same dense non porous antimonial lead alloy. This is generally due to their important specific surface area where oxidation-reduction reactions took place. A correlation between the effective electrical conductivity and the cell diameter has been established and the highest conductivity was obtained with a cell diameter of 5mm. The feasibility of such an electrical system has been demonstrated.

We determined the optimal composition of reactive magnetron sputtered TiO2-SnO2 mixed layers for electrochromic purposes. We determined and mapped the composition and optical parameters by Spectroscopic Ellipsometry (SE). The Ti‐ and Sn‐ targets have been placed separately, and the Si-wafers on glass substrate (30 cm× 30 cm) were moved under the two separated targets (Ti and Sn) in Ar‐O2 plasma. Different (Effective Medium Approximation (EMA) and oscillator-type) op-tical models were used to obtain the composition maps and thickness of the sample layer. Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS) has been used to check the SE results. The ’goodness’ of diverse optical models have been compared, according to the conditions of sample preparation. We show that in the case of molecular-level mixed layers 2‐Tauc‐Lorentz oscillator model is better than the Bruggeman Effective Medium Approximation (BEMA). The electrochromic properties of mixed metal oxides that deposited by reactive sputtering have been mapped, too.

We propose a thermodynamic model describing the thermoelastic behavior of composition graded materials. The compatibility of the model with second law of thermodynamics is explored by applying a generalized Coleman-Noll procedure. We calculate the speeds of coupled first- and second-sound pulses, propagating either trough nonequilibrium or trough equilibrium states. We characterize several different types of perturbations, depending on the value of the material coefficients. Under the assumption that the deformation of the body can produce changes in its stoichiometry, altering locally the material composition, the possibility of propagation of pure stoichiometric waves is pointed out. Thermoelastic perturbations generated by the coupling of stoichiometric and thermal effects are analyzed as well.

The aim of this study was to evaluate and compare the fracture resistance of definitive zirconia dioxide restorations obtained using a computer-aided design and manufacturing (CAD/CAM) system. Methods: Two groups of ten samples were analyzed for each material (n: 20), the first group was Zolid Gen X Amann Girrbach (ZGX) and the second group was Cercon HT Dentsply Sirona (CDS). The restorations were designed with identical parameters and milled with a CAD/CAM system. Each specimen was load tested at a speed of 0.5 mm/min with a direction parallel to the major axis of the tooth and with an initial preload of 10N until fracture using a universal testing machine (Universal/Tensile Testing Machine, Autograph AGS-X Series) equipped with a 20 kN load cell. The results obtained were recorded in Newtons (N), using software connected to the testing machine. Results: Statistically significant differences were found, and the fracture toughness of the monolithic zirconia crowns was lower in the CDS group (1744.84 ± 172.8 N), compared to the ZGX group (2387.41 ± 516 N). Conclusions: The monolithic zirconia CAD-CAM zirconia crowns showed sufficient fracture strength to be used in posterior molar and premolar zones with either material as they withstood fracture loads greater than the maximum masticatory force.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

Smart flexible materials with piezoresistive property are increasingly used in sensors field. When embedded in structures, they would allow an in-situ structural health monitoring and damage assessment of impact loading such as crash, bird strikes and ballistic impacts. However, this could not be achieved without a deep characterization of the relation between piezoresistivity and mechanical behavior. The aim of this paper is to study the potential use of the piezoresistivity effect of a conductive foam made of a flexible polyurethane matrix filled with active carbon for integrated Structural Health Monitoring (SHM) and damage assessment applications. To do so, PolyUrethane Foam filled with Active Carbon, namely PUF-AC, are manufactured and tested under quasi-static compression tests and under Dynamic Mechanical Analyser (DMA) with in-situ measurement of its resistivity during tests. A relation is proposed for describing the evolution of the resistivity versus strain and stress. In addition, a demonstrative experiment of a PUF-AC sample subjected to low velocity impact assesses the interest of this type of materials for damage assessments.

Optimum design and accurate control of the internal structure of the laser target materials remain an important goal for various laser physics experiments, especially for generating high flux photon and neutron beams. The low-density material is considered to be one of the most difficult for X-ray study due to its high transparency and imperceptible contrast. To produce clear visualization of foam containing sparse structures we used a high-quality monochromatic X-ray beam of synchrotron radiation source PETRA-III at DESY. The X-ray beam parameters allow tomographic scanning with application of phase contrast retrieval algorithms. A series of 3D images of foam-suspended glass microsphere inside the plastic cylinder were obtained with the quality high enough to observe the internal structure and to visualize uniformity, displacement and surface roughness on both sides of the microsphere. The main object under investigation was a CH-plastic capillary including 10 mg/cc CHO-foam with the centered glass microsphere. The results of this work demonstrate that tomographic visualization based on a high quality X-ray radiation and phase contrast analysis is an effective and useful technique for development of new laser targets containing structured low density materials.

In the last two decades, the continuous ever growing demand for energy has determined a significant development in the production of photovoltaic (PV) modules. Anyway, a critical and very important issue in the module design process is the adoption of suitable encapsulant materials and technologies for cell embedding. Therefore, adopted encapsulants have a significant impact on modules efficiency, stability and reliability, and to ensure the unchanged performance of PV modules in time, the encapsulant materials must be selected properly. The selection of encapsulant materials must maintain a good balance between the encapsulant performance in time and costs, related to materials production and technologies for cells embedding. However, the encapsulants must ensure excellent isolation of active photovoltaic elements by the environment, preserving accurately the PV cells against humidity, oxygen and accidental causes that may compromise the PV modules function. This review provides an overview of different encapsulant materials, their main advantages and disadvantages in adoption for PV production, and also in relation to used encapsulant technologies for cell embedding, additives and the interaction of these materials with other PV components.

Knowledge of the temperature evolution is crucial to understand and control laser beam welding of low-melting materials. Existing temperature determination approaches are restricted to i) one-dimensional temperature information (e.g. ratio-pyrometers), ii) a priori knowledge of the emissivity (e.g. thermography) and iii) high temperature regions (e.g. two-wavelength imaging). In this paper, a ratio-based two-color-thermography approach is developed that allows for two-dimensional temperature determination in low-melting temperature ranges (< 1200 K). For static measurement situations it is demonstrated, that temperature can be determined despite variation in signal intensity and emissivity with high accuracy. The two-color-thermography set-up is further transferred into a commercial laser beam welding machine and experiments are conducted for varying process parameters. The direct application of the developed two-color-thermography system in dynamic process situations is limited as image artifacts presumably caused by internal reflections inside the optical beam path are present.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

Two-dimensional (2D) materials have been a research hot topic in the passed decades due to their unique and fascinating properties. Among them, mechanical properties plays an important role for their application. However, there lacks an effective tool for high-throughput calculating, analysing and visualizing the mechanical properties of 2D materials. In this work, we present, mech2d package, a highly automated toolkit for calculating and analysing second-order elastic constants (SOECs) tensor and relevant properties of 2D materials with considering their symmetry. In the mech2d, the SOECs can be fitted by both strain-energy and stress-strain approach, where the energy or strain can be calculated by first-principles engine, such as VASP. As a key feature, the mech2d package can automatically submit and collect the tasks from local or remote machine with robust fault-tolerant ability, make it suitable for high-throughput calculation. The present code has been validated by several common 2D materials, including graphene, black phosphorene, GeSe2 and so on.

Mobile robots can perform tasks on the move, including exploring terrain, discovering landmark features or moving a load from one place to another. This group of robots is characterized by a certain level of intelligence allowing making decisions and responding to stimuli received from the environment. As part of Industry 5.0, such mobile robots and humans are expected to co-exist and work together in a shared environment to make human work less tiring, quicker, and safer. This can only be realized when clean, dense, and economical energy sources are available. The aim of the study is to analyze the state of the art and to identify the most important directions for future developments in robotic power systems based mainly on batteries. The efficiency and performance of the battery depends on the design using different materials. Work environments and performance requirements are considered in this systematic review to classify solutions that help developers choose the best suited power system for specific application. Indirectly, the aim of the work is to generate discussion within the scientific and engineering community. A narrative review of publications from six major bibliographic databases according to preset inclusion criteria was combined with a critical analysis of current and future technologies. The main findings of the review allow answering question what is the role of modern power source technologies, artificial intelligence and ground-breaking research work in global policies related to energy saving, green policies, and sustainable development. The main opportunities and threats are discussed, and a brief feasibility analysis is carried out. Novelty of the article relates not only to the analysis of technologies, but also to approaches and their use under conditions of limited resource availability, when resource usage must be minimized. The article provides an overview of batteries, their specifications, classifications, and their advantages and disadvantages. In addition, we propose: (1) an algorithm for selecting main energy source for robot application, and (2) an algorithm for selecting electrical system power supply. Current mobile robot batteries are, in most cases, their biggest limitation. Progress in batteries development is too slow to catch up with the demand for robot autonomy and range requirements, limiting the development of mobile robots. Further intensive research and implementation work is needed to avoid years of delay in this area.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.