The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

A study on flywheel geometries is presented here with the use of finite element modelling (FEM) simulations. The study analyses the stress behaviour of flywheel rotors subject to the rotational speed that creates the maximum stress that the flywheel can support, and then calculates the rotational energy mass ratio (energy density) for each geometry. The obtained geometry was Gaussian section for the Flywheel rotor. The used material for the simulations is carbon fibre Hexcel UHM 12000. The best results were a rotational speed of ≈279.000 rpm and rotational energy density of ≈ 440 Wh/kg for a single disk, but this keeps the total energy low. To increase the total energy, Flywheels with 2 and 3 rotors were analysed. Then the stability under rotation of these Flywheels were analysed, some instability was found and a solution was presented.

The research on the distribution of rural buildings is one of the fundamental works of urban-rural development in Vietnam. Adopting Mask R-CNN deep learning framework and collecting sub-meter remote sensing images, this research used a remote sensing interpretation model of rural buildings trained based on East Asian characteristics of rural buildings and successfully recognized about 2.87 million rural buildings in 34 Vietnamese provincial administrative districts with a total area of rural buildings of 2,492 million square meters. The reliability of the identification results was verified by manual detection and quantitative statistics, and a multi-scale database of rural buildings in Vietnam based on individual rural buildings was created. Based on the database, this paper analyzes the distribution characteristics of rural buildings and summarizes characteristics of rural buildings distribution at the country, regional, and provincial scales. The identification results lay the foundation for the next study of urban-rural relations in Southeast Asia and the construction of a basic database on villages.

The main advantage of using the ferroelectric material as a component of complex heterostructure is the ability to tune various properties of the whole system by means of external electric field. In particular, the electric field may change the polarization direction within the ferroelectric material and consequently affect the structural properties, which in turn affects the electronic and magnetic properties of the neighboring material. Besides, the ferroelectrics proceed the electrostriction phenomenon, which is promising to be used to affect the magnetic states of interface state in the heterostructure with a magnetic component. The interfacial phenomena are of a great interest since they provide an extended functionality useful for electronic devices of a new generation. Following an idea of utilizing a ferroelectric in heterostructures component in the present work we consider 2DEG, Rashba effect, the effect of magnetoelectric coupling and magnetostriction in order to emphasize the advantages of such heterostructures as components of devices. For this purpose model systems of LaMnO3/BaTiO3, La2CuO4/BaTiO3, Bi/BaTiO3 and Bi/PbTiO3, Fe/BaTiO3 heterostructures are investigated by density functional theory calculations.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

The present review article concludes with three different types of materials recently used to enhance the efficiency of supercapacitors. The first type involves carbon-based materials for storage and supercapacitor applications. The carbon materials could be obtained naturally and synthesized manually based on the needs. The second type discusses the recent advances in metal oxide materials for high-performance supercapacitors. The metal oxide materials involve in different types of attachment through the bi-tri metallic bonding, which enhances the specific capacitance. The third type involves recently advanced materials for high energy and power density application. The power and energy density of the materials is enhanced by the surface modification of the materials. In recent days, the MXene and Nano-composite materials seems to be an appropriate material to increase the power and energy density of the device.

The false codling moth (FCM), Thaumatotibia leucotreta (Meyrick), is believed to have originated from Ethiopia and sub-Saharan Africa. Currently, this pest has extensively spread and is found in most parts of Africa, with records in approximately 40 countries in over 100 host plant species. Despite Thaumatotibia leucotreta being the leading cause of interceptions of Capsicum and cut flowers exported by Kenya to the European Union, information on abundance and damage levels inflicted on capsicum is limited. The objective of the study was to assess the abundance and damage levels of T. leucotreta on capsicum in the selected counties in Lower Eastern Kenya (Kitui, Machakos, and Makueni counties). Higher T.leucotreta larval density per farm was recorded in Kitui County compared to other counties. In farms with capsicum only (not intercropped with other crops), the mean number of FCM larvae was relatively higher in Kitui. Farming practices such as the use of uncertified seeds and seedlings and the excessive use of pesticides may be the major contributors to high larval incidence in Kitui County.

Phase synchronization of weakly coupled limit cycle oscillators are related to the stability of the zero solution of the reduced-order dynamics of phase differences, represented by a systems of differential equations on a hypertorus. Using Rantzer's density function, a dual form of Lyapunov function, we propose a method to certify almost global stability of an equilibrium on a hypertorus. We show that the proposed method can certify robustness of phase synchronization of all-to-all and weakly coupled limit cycle oscillators with respect to disturbances in phases. The method leverages sum of squares polynomial optimization to construct the certification function.

This study investigated the development of Aedes aegypti density in houses of the urban locality of Poblado Miguel Alemán Valdes, in the Sonora state of Mexico, after application of 1% propoxur paint as full wall coverage (IP) and targeted indoor painting (IP 1m) in comparison to IRS with propoxur 70% WP (full wall coverage). The 1% propoxur paint was applied by the homeowners by brushing and rolling at the recommended dose of 1L/8 m², equivalent to 1.5 g a.i./m², while IRS was conducted by professionals with Propoxur 70% WP at a dose of 1 g a.i./m². Adult mosquito surveys were conducted in a random sample of houses in each block one week before the interventions and at week 1, month 1 to 4, month 6, month 9 and month 12 post-interventions. All three propoxur based treatments provided similar reductions (43.7%, 44.9% and 41.3% for IP, IP 1m and IRS respectively) in the fraction of houses positive in female Aedes aegypti resting indoor and outdoor as one year average of 8 follow up surveys. Indoor resting density of Aedes females during the one-year evaluation was reduced by 77.5% through IP followed by IP 1m with 64.2% reduction and 30% reduction with IRS. Culex mosquitoes’ interior density was affected as well by the insecticide treatments with similar average reductions for IP 1m (50.0%) and IRS (57.8%) in comparison with control. Aedes breeding was impacted by the insecticide paint in similar extent for both interventions, expressed by a substantial reduction of the House Index (20.1% IP, 31.2% IP 1m) and especially the Container Index (51.8% IP, 61.7% IP 1m) during the one-year surveys in comparison to control. In contrast, IRS treated block experienced an increase in both indexes. However, despite IP and IP 1m impacted in Aedes adult and immature indexes with noticeable reductions, the differences in all cases were not significative among the different insecticide treatments. The low sample size and mosquito population levels may have influenced the statistical outcomes. More than 80% of the interviewed residents were satisfied with the effectiveness of the paint and IRS treatments. The determination of the blood cholinesterase activity of tested individuals after the use of the carbamate paint and IRS in this study did not exceed acceptable inhibition limits. This study suggests that the application of propoxur paint by homeowners as full house coverage or as targeted indoor painting can be a safe and accepted intervention method for density reduction of Aedes aegypti populations in urban environments.

Three genera of very large volant birds existed for most of the Pliocene: the Pelagornithidae seabirds; the large North American Teratornithidae and the stork Leptoptilos falconeri in Africa and Asia. All became extinct around 3 Ma. The reasons for their demise are puzzling, as the Pelagornithidae had a world-wide evolutionary history of more than 50 Ma, smaller teratorns were still extant in the Holocene and smaller stork species are still globally extant. Extant large birds have a common critical takeoff airspeed suggesting a biomechanical limit in terms of power, risk and launch speed, and simulations of the flight of these extinct species suggest that at 1 bar they would have exceeded this value. Estimates for the Late Pliocene atmospheric density are derived from marine and terrestrial isotopes as well as resin chemistry, both approaches suggesting a value of about 1.2 bar, which drops to present levels during the period 3.3 to 2.6 Ma, thus a loss in atmospheric density may have caused biomechanical and ecological stress contributing to their extinction and/or development of smaller forms. This hypothesis is examined in terms of a possible mechanism of atmospheric mass loss and how this would be seen in the geological record. At 1.2 bar all the extinct species present takeoff airspeeds similar to large extant volant birds and which match the expected power and kinetic energy levels.

The COVID-19 pandemic of 2020 changed the way we interact and engage in commerce at a fundamental level. Social distancing and stay-at-home orders leave businesses and cities wondering what economic activity will look like in the future. Given a likely reduction in face-to-face interactions, it is important to better understand how social interactivity influences economic outcomes. Here we measure the effect of social interactions in the workforce on patent production and economic efficiency. We decompose U.S. occupations into individual work activities, determine which of those activities are associated with face-to-face interactions, and reaggregate the labor force of each U.S. metropolitan statistical area (MSA) into a metric of social interactiveness. We then calculate each MSA’s density of social work activities and find that this measure is more highly correlated with an MSA’s per capita patent production than simple population density. This suggests that density of face-to-face interactions is the important driver of a city’s rate of invention. We close by exploring analogies between the development of cities and the development of stars, suggesting ways these analogies may help frame future research on cities.

A low calcium intake is associated with an increased fracture risk. We assessed the dietary calcium intake in a cohort of Italian individuals evaluated for low bone mineral density (BMD). A 7-day food-frequency questionnaire was administered to 1793 individuals consecutively referred at a Centre of the Italian Society for Osteoporosis, Mineral Metabolism and Skeletal Diseases for low BMD. In 30.3% (544/1793) and 20.9% (374/1793) of subjects the calcium intake was inadequate ( <700 mg/day) and adequate (>1200 mg/day), respectively. Patients with calcium intake <700 mg/day showed a higher prevalence of diabetes mellitus, idiopathic hypercalciuria and food allergy/intolerance (8.1%, 5.1%, 7.2%, respectively) than patients with calcium intake >700 mg/day (5.3%, 3.0%, 4.1%, respectively, p<0.04 for all comparisons), also after adjusting for age, gender and BMI. In 30.3% of fractured subjects the calcium intake was <700 mg/day. In Italy, a low calcium intake is highly prevalent in individuals at risk for low BMD. Importantly, an inadequate calcium intake is highly prevalent even in patients with history of fragility fractures. Only about a fifth of patients at risk for low BMD reported an adequate calcium intake

Significant progress has made in pattern recognition technology. However, one obstacle that has not yet overcome is the recognition of words in the Brahmi script, specifically the recognition of characters, compound characters, and word because of complex structure. For this kind of complex pattern recognition problem, it is always difficult to decide which feature extraction and classifier would be the best choice. Moreover, it is also true that different feature extraction and classifiers offer complementary information about the patterns to be classified. Therefore, combining feature extraction and classifiers, in an intelligent way, can be beneficial compared to using any single feature extraction. This study proposed the combination of HOG +zonal density with SVM to recognize the Brahmi words. Keeping these facts in mind, in this paper, information provided by structural and statistical based features are combined using SVM classifier for script recognition (word-level) purpose from the Brahmi words images. Brahmi word dataset contains 6,475 and 536 images of Brahmi words of 170 classes for the training and testing, respectively, and the database is made freely available. The word samples from the mentioned database are classified based on the confidence scores provided by support vector machine (SVM) classifier while HOG and zonal density use to extract the features of Brahmi words. Maximum accuracy suggested by system is 95.17% which is better than previously suggested studies.

Understanding the physical properties of ultramafic rocks is important for evaluating awide variety of petrologic models of the oceanic lithosphere, particularly upper mantle and lower crust. Hydration of oceanic peridotites results in increasing serpentine content, which affects lithospheric physical properties and the global bio/geochemical cycles of various elements. In understanding tectonic, magmatic and metamorphic history of the oceanic crust, interpreting seismic velocities, rock composition and elastic moduli are of fundamental importance. In this study we show that as serpentine content increases, density decreases linearly with a slope of 7.85. We also correlate increase in serpentine content with a linear decline in shear, bulk and Young’s moduli with slopes of 0.48, 0.77, 0.45 respectively. Our results show that increase in serpentine content of lower crust and forearc mantle could decrease elasticity of lithospehere and result in break-offs. Therefore tectonic processes at peridotite rich slow spreading ridges may be strongly affected by serpentine content, particularly serpentinization may be responsible for discontinuities in thin crust, and formation of weak fault zones.

To generate a probability density function (PDF) for fitting probability distributions of real data, this study proposes a deep learning method which consists of two stages: (1) a training stage for estimating the cumulative distribution function (CDF) and (2) a performing stage for predicting the corresponding PDF. The CDFs of common probability distributions can be adopted as activation functions in the hidden layers of the proposed deep learning model for learning actual cumulative probabilities, and the differential equation of trained deep learning model can be used to estimate the PDF. To evaluate the proposed method, numerical experiments with single and mixed distributions are performed. The experimental results show that the values of both CDF and PDF can be precisely estimated by the proposed method.

The dislocation density tensors of thin elastic shells have been formulated explicitly in terms of the Riemann curvature tensor. The formulation reveals that the dislocation density of the shells is proportional to KA3=2, where K is the Gauss curvature and A is the determinant of metric tensor of the middle surface.

Water treatment efficiency of several filter media such as perlite, modified (silicated) perlite, zeolite and sand were studied on wastewater. This study contains 2 distinct experiments which the first one emphasize on the modified perlite’s performance in removing turbidity which has been gone through 3 phases including low turbidity model water, mid turbidity and high turbidity model water; the second experiment underlines the differentiation between 3 evolutionary material based on perlite which undergoes the filtration process with certain turbid model water. It was dedicated that modified perlite removed more than 90% of turbidity and it functions better than other materials with high turbidity (more than100 NTU). The experiments have been conducted with sodium silicate perlite, normal perlite and synthetic zeolite perlite in order to determine the optimized material which is able to be substituted with perlite in the filtration process.

Fractal array antennas are multiband arrays having ultra wide band and space filling facility. But Side lobe levels and large number of antenna elements are the major designing challenges of these arrays. In this paper, design and analysis of octagonal fractal array antenna is investigated with Morse-Thue fractal density tapering technique (MTFDT). Due to the proposed technique, a remarkable improvement has observed in Side lobe levels and thinning of the elements can also be attained at the various iterations of octagonal fractal array antenna. These arrays are analyzed and simulated by MATLAB-15 programming.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Background: Protein CCDC186 is involved in the maturation of dense core vesicles in the trans-Golgi network in neurons and endocrine cells. To date, only one patient, within a large sequencing study of 1000 cases, and a single case report with variants in CCDC186 had previously been described. However, no functional studies in any of these two cases had been performed. Methods: Exome sequencing from one affected individual of each family was performed. In addition, Sanger sequencing of the parents and one of the affected siblings was also performed. CCDC186 protein was assessed in cultured fibroblasts or muscle tissue by western blot. Transcriptomic analysis was done by means of RNA sequencing. Results. We identified three patients from two gypsy families, unrelated to each other, with the same homozygous mutations in CCDC186 gene. Clinically, all patients presented with seizures, frontotemporal atrophy, hypomyelination, recurrent infections, and endocrine disturbances such as severe non ketotic hypoglycemia. Low levels of cortisol, insulin or growth hormone could only be verified in one patient. All of them had a neonatal onset and died between 7 months and 4 years of age. WES identified a homozygous variant in CCDC186 gene (c.2215C>T, p.Arg739Ter) in the index patients of both families. Protein expression studies demonstrated that the CCDC186 was practically undetectable in fibroblasts and muscle tissue. These observations correlated perfectly with the transcriptomic analysis performed in fibroblasts in one of the patients, which showed a significant reduction of CCDC186 mRNA levels. Conclusion. Our study provides functional evidence that mutations in this gene have a pathogenic effect on the protein and reinforces CCDC186 as a new disease-associated gene. In addition, mutations in CCDC186 could explain the combined endocrine and neurologic alterations detected in our patients

This paper aims at trying to answer the question of whether a low cost drone equipped with a regular camera can serve as a simple device to estimate the size of objects. Ad-ditionally, it assesses if the accuracy of measurement is good enough for using a drone for measurements, relying solely on GPS position and camera. A review of the literature pertaining to ground object measurements was conducted. The availability of such in-struments was evaluated in terms of purchase and rental costs, the number of instru-ments on the market, and the time to obtain them. The most common measurement methods were considered and their unit costs were reviewed. The cost of professional surveying and measuring equipment was compared to the possibility of using low-cost, non-commercial drones to measure objects and surfaces. The quality of the images ob-tained was compared with high-resolution satellite systems. Is an ordinary drone with a standard camera suitable for length measurement without professional measuring equipment? Should the results be considered only in the category of size estimation?

One of the key issues in sustainable tourism research is the gap between tourists' expressed friendly attitudes towards sustainable behaviors and their actual behaviors. Although many "low-carbon" themed restaurants have emerged during the low-carbon transformation of the Chinese tourism industry, low-carbon food services have not been significantly improved. This study takes food as the entry point to explore tourists' behavior and attitudes towards low-carbon tourism in relation to food. We conducted two interviews. The first interview was a semi-structured contextual interview with 120 tourists who had experiences in food streets, aim-ing to identify the core user group: low-carbon attitude-friendly tourists with high-carbon food behaviors. The second interviews was an in-depth interview based on grounded theory with 29 core users, analyzing the four main reasons for their high-carbon food behaviors and their re-quirements for low-carbon food services in tourism. Based on this, we extracted four design ele-ments for low-carbon tourism food services: low-carbon information show service, low-carbon service product attractiveness improvement, low-carbon food environment atmosphere creation, and service providers' low-carbon behaviors. Through these four service elements, we constructed a low-carbon tourism food service design framework based on the core users' needs, discussed the mechanism of service elements, and provided service design suggestions accordingly. The re-search results serve tourism providers, low-carbon tourism researchers, and designers.

Chronic pain is a serious health concern and potentially debilitating condition, leading to anxiety, depression, reduced productivity and functionality, and poor quality of life. This condition can be even more detrimental and incapacitating in the pediatric patient population. In low and middle income countries (LMICs), pain services are inadequate or unavailable, leaving most of the world's pediatric population with chronic pain untreated. Many of these children in LMICs are suffering without treatment, and often die in pain. Awareness and advocacy for this population must be prioritized. We reviewed the available literature on the chronic pediatric pain burden in LMICs, barriers to treatments, and current efforts to treat these patients.

The textbook analysis of vacuum energy density (VED) in flat spacetime follows from Pauli’s lectures of 1951, in which quantum vacuum is modeled as a reservoir of free harmonic oscillators. In his lectures, Pauli shows that deriving a nearly vanishing VED is contingent upon fulfilling three corollary conditions called polynomial-in-mass-constraints. The goal of this work is to evaluate Pauli’s constraints against the Standard Model parameters and the Higgs mechanism of spontaneous symmetry breaking.

Several Lung diseases can result in lung damage structural changes, with lung transplantation as a only therapeutic option when the disease reaches an advanced progression, unfortunately, the success of lung transplantation is limited. In this context, lung bioengineering is considered a potential therapeutic alternative and the current approach is based on the use of the natural extracellular matrix (ECM) of the decellularized lung. The use of undifferentiated cells to seed an ECM can be a more practical strategy for lung bioengineering but the sterilization of the organ for this recellularization process is still a challenge. In this sense, Low-Level Laser Therapy (LLLT) can emerge as a potential treatment alternative. Therefore, the objective of this study was to verify if LLLT, can optimize lung recelularization with mesenchymal stem cells by cytokine modulation. For this, we decellularized lungs from C57BL/6 mice perfusing SDS 1% via pulmonary artery, sterilized with LLL (660nm, 100mW, 30s). Whole lung scaffolds were recellularized: (1) Recellularized Lung (2) Recellularized Lung + LLLT. Mesenchymal stem cells derived from human tooth pulp (DPSc) were seeded into lungs and incubated for 24 hours at 37ºC, 5% CO₂, in a bioreactor-like conditions, maintaining CPAP at 20cmH2O, 90% O2, and LLL at wavelength of 808nm, 100mW, 30s. Culture medium were analyzed at 24 hours. H&amp;E, immunostaining, SEM and ELISA assay were performed. We produced viable biological scaffolds absent of DNA content, preserving glycosaminoglycans and collagen I, III and IV, fibronectin, laminin and elastin and lung structure (SEM). The levels of IL-6 and IL-8 were stable during the 24 hours of culture. IFN-γ levels showed significant difference in the DPSc and DPSc+LLLT group in the 24-hour evaluation. The levels of IL-10 decreased after LLLT. These findings highlight LLLT's role in cytokine regulation and contamination prevention during lung recellularization with mesenchymal stem cells. Overall, these results demonstrated that LLLT's modulated cytokine levels and could prevent contamination during the lung recellularization process with mesenchymal stem cells, offering promise for enhanced therapeutic strategies in lung bioengineering

To investigate the structural behavior of simply supported concrete beams with steel and polypropylene fiber under low velocity impact loading. In all twenty-four beams (150X200X1800 mm) with simply supported boundary condition were modeled and analyzed using ABAQUS software. Steel and polypropylene fibers of aspect ratio of 60 and 231 respectively are used. The total volumes of fibers are maintained at 1% by volume of specimen. A 100 kg hammer with tip diameter 16 mm (hemispherical contact area = 201 mm2) with four different velocities (3.13 m/s, 4.42 m/s, 5.43 m/s and 6.11 m/s) were used in the analysis. It is observed that with the addition of hybrid fibers the deflection in beams was reduced. The beams with 1% PP and 0% steel fiber shows the maximum deflection values due to low modulus of elasticity. Beams with 0.9% steel and 0.1% polypropylene fibers was less affected in terms of deflection as compared to all other beams, it is due to presence of high tensile strength fibers.

Phenylketonuria is an inherited metabolic disorder that leads to neurobehavioral dysfunction. The main treatment is a low-phenylalanine diet and/or the cofactor tetrahydrobiopterin. Regular outpatient follow-up care and measurement of the phenylalanine level in the blood are required. We aimed to analyze the economic burden of phenylketonuria on families and the state. The pa-tients with phenylketonuria were divided into three groups according to their treatment: a low-phenylalanine diet group (n= 50), a tetrahydrobiopterin group (n= 44) and a group taking tetra-hydrobiopterin together with the diet (n= 25). A comparative cost analysis was carried out. The annual economic burden to the state was calculated to average €18801±15345 and was lowest in the diet group, then in the tetrahydrobiopterin group and highest in the tetrahydrobiopterin+diet group (p < 0.001). Out-of-pocket costs amounted to €1531±1173 per year, and indirect losses aver-aged €2125±1930 per year for all families. The economic loss was significantly lower in the fami-lies taking tetrahydrobiopterin than in the other groups (p=0.001). The combined use of medical nutrition and BH4 treatments has been shown to increase the economic harm to the state. Reim-bursing low-protein products and increasing the rate of patients eligible for financial allowances may reduce the economic harm to families.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

The low-altitude quasi-periodic (LQP) E-region echoes observed with the upgraded HCOPAR located in Hainan Island of China (19.5°N, 109.1°E) are presented. With the interferometry technique, the interferometry equations can be developed to investigate the structures of the irregularities. The results show that the plasma structures of the LQP echoes with negative slope mainly drift southwestward almost horizontally, but they also drifted southeastward in some striations. According to the movement of the plasma structures, we find strong wind shear in the region where the LQP echoes are produced. Meanwhile, The periodicity of the LQP echoes may be related to the strength of the wind shear. It is proposed that the plasma structures are most likely produced by the Kelvin-Helmholtz instability.

Glucose is an important carbon sources for microbial growth, and its content in infertile soils is essential for the growth of the bacterium. Since the mechanism of oligotrophic bacterium adaptation in barren soils is unclear, the research employed RNA Seq technology to examine the impact of glucose concentration on the low nutrient bacteria BS-G1 in soil affected by desertification. RNA-Seq revealed that differentially expressed genes（DEG）histidine metabolism, glutamate synthesis, HIF-1 signalling pathway, sporulation, and TCA cycle pathway of BS-G1 were significantly enriched in 0.015 g/L glucose concentration, compared with 10 g/L glucose concentration. DEG amino acids system, two-component system, Metal Ion Transport, and nitrogen metabolism system of B. subtilis BS-G1 were significantly enriched in 5 g/L glucose concentration, compared with 10 g/L glucose concentration. In addition, The present study identified its regulation pattern and key genes under the low glucose environment (7 mRNAs, 16 sRNAs). This study primarily investigates the variances in the regulatory pathways of oligotrophic bacteria BS-G1, which holds substantial importance in comprehending the mechanism underlying the limited sugar tolerance of oligotrophic bacteria.

Regulatory monitoring networks are often too sparse to support community-scale PM2.5 exposure assessment while emerging low-cost sensors have the potential to fill in the gaps. Recent advances in air quality monitoring have produced portable, easy-to use, low-cost, sensor-based monitors, which has given a new dimension to the air pollutant monitoring and has democratized the air quality monitoring process by making monitors and results directly available at community level. This study used PurpleAir(c) sensors for PM2.5 assessment in California, USA. Evaluation of PM2.5 from sensors included Quality Assurance &amp; Quality Control (QAQC) procedures, assessment with respect to reference monitored PM2.5 concentrations, and formulation of a decision support system integrating these observations using geostatistical techniques. The hourly and daily average observed PM2.5 concentrations from PurpleAir monitors followed the trends of observed PM2.5 at regulatory monitors. PurpleAir monitored PM2.5 also captured the peak PM2.5 concentrations due to incidents like forest fire. In comparison with reference monitored PM2.5 levels, it was found that PurpleAir PM2.5 concentrations were mostly higher. The most important reason for PurpleAir higher PM2.5 concentrations was the inclusion of moisture or water vapor as aerosol in contrast to measurements of PM2.5 excluding water content in FEM/FRM and non-FEM/FRM monitors. On long term assessment (2016-2020), R2 was between 0.54 and 0.86 at selected collocated PurpleAir and regulatory monitors for hourly PM2.5 concentrations. Past research studies have been conducted for mostly shorter time periods (&lt;3-4 months) that resulted in higher R2 values between 0.80 to 0.98. This study aims to provide reasonable estimations of PM2.5 concentrations with high spatiotemporal resolutions based on statistical models using PurpleAir measurements. The methods of Kriging and IDW, geostatistical interpolation techniques, showed similar spatio-temporal patterns. Overall, this study revealed that low-cost, sensor based PurpleAir sensors could be effective and reliable tools for episodic and long-term ambient air quality monitoring.

Most of the fishing currently practiced in Japan is done by small vessels with a small number of fishermen (one or two). One of the most common fishing methods is longline fishing. However, this method requires the vessel to operate at a constant low speed because the depth of the hook must be kept constant while adjusting the speed of the fishing boat to the tidal current. In addition, because the vessel must maneuver and fish at the same time, automation is desired. Thus, we propose a robotic system that can control the depth of the trap at a constant depth even when the speed of the vessel and the current change, and that can successfully fish without the need for skilled fishermen. Fishing can be conducted regardless of the speed of the vessel, whereas currently it is controlled by the speed of the vessel and the tidal current. Therefore, it may contribute to proposing new fishing methods as well as the existing ones. This can contribute to the shortage of successors to the fishing industry and to the revitalization of the fishing industry.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

The paper explores the potential of a low-cost advanced video-based technique for the assessment of structural damage induced to buildings by seismic loading. A low-cost high-speed video camera was utilized for motion magnification (MM) processing of footages of a two-story reinforced concrete frame building subjected to shaking table tests. The damage after seismic loading was estimated by analyzing the dynamic behavior (i.e. in terms of modal parameters) and the structural deformations of the building in the MM videos. The results by MM were compared for method validation to damage assessment obtained by the analyses of conventional accelerometers and high-precision optical markers tracked by a passive 3D motion capture system. Also, 3D laser scanning to obtain an accurate survey of the building geometry before and after the seismic tests was carried out. In particular, accelerometers were also processed and analyzed by using several stationary and non-stationary techniques with the aim to analyze the linear behavior of the undamaged structure and the nonlinear structural behavior during damaging shaking table tests. The proposed MM-based procedure provided accurate estimate of the main modal frequency and the damage location through the analysis of modal shapes, which were confirmed by advanced analyses of accelerometric data.

In this study, we explore the potential of using a straightforward neural network inspired by the retina model to efficiently restore low-light images. The retina model imitates the neurophysiological principles and dynamics of various optical neurons. Our proposed neural network model reduces the computational overhead compared to traditional signal-processing models while achieving results similar to complex deep learning models from a subjective perceptual perspective. By directly simulating retinal neuron functionalities with neural networks, we not only avoid manual parameter optimization but also lay the groundwork for constructing artificial versions of specific neurobiological organizations.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

The goal of classroom English instruction is to educate students on how to use the English language effectively for communication in any scenario. It is identified by presenting various teaching tactics and speaking activities to encourage students to participate more actively in conversations. The study intended to identify the problems in the speaking performance of Grade 8 Jade in Tagum City National High School. The study was conducted using a quantitative non-experimental descriptive survey method. Results revealed that the problems in speaking performance have garnered a mean of 3.20 (moderate) as descriptive equivalent and it was found out that the prevailing speaking problem is anxiety with a mean of 3.84, interpreted as high. Thus, an intervention program is designed to address the problems in the speaking performance of the respondents. This program is divided into two: Overcoming Speaking Anxiety Seminar-Workshop and Speaking Enhancement Activities.

Low back pain is a common problem in the active population, and the second reason for visiting a physician. In patients with lumbar disc protrusion, the nucleus pulposus bulges against the disc and the latter protrudes into the spinal column, but the annulus fibrosus remains intact. The purpose of this study was to prove that starting an early complex rehabilitation treatment results into pain and disability reduction, and increased muscle strength and mobility in patients with lumbar disc protrusions. We performed a prospective cohort study, enrolling 60 patients (25 men and 35 women) aged between 26 to 76 years, diagnosed with lumbar disc protrusion. Patients in the experimental group registered significant improvements in all studied variables (pain, mobility, muscle strength, disability) after 6 months of treatment. The results of our study suggest that, in the lumbar disc disease, a combined rehabilitation program may be more effective in terms of pain and disability reduction, if it starts early after diagnosis. The current study proves the importance of combining electrotherapy with hydrotherapy and physical therapy. Patients who received this treatment combination showed an extremely significant improvement in pain relief, and reduction of functional disability after 6 months of treatment.

Pepper plants experience complex environmental factors including abiotic and biotic stresses in field and the importance of climate changes including low and high temperatures has been emerged. Low temperature stress in the growth and development is one of the most critical issues, which directly impact on the crop yield and productivity of pepper plants. It is essential to select and breed low temperature-(LT) tolerant pepper (Capsicum annuum L.) cultivars. The research was performed to assess the agronomical traits of 39 pepper accessions belonging to chili and bell fruit types which cultivated two different night temperature set-points at 15°C for suboptimal temperature (CT) and at 10°C for low temperature (LT), respectively. Plant heights (PH) of most pepper accessions in LT were significantly decreased compared to those in CT. The stem diameter (SD) and the length of main axis (LMA) were various depending on the genotypes under LT. Moreover, the number of flowers (NFL), the total number of fruits (NFR), fruit yield (FY), fruit fresh weight (FFW), fruit length (FL), fruit diameter (FD), and the number of seeds in a fruit (NSF) were notably declined in LT compared to CT. The evaluated agronomical traits between LT and CT were further applied for the correlation analysis, the principal component analysis (PCA), and the hierarchical cluster analysis. Notably, FY trait was correlated with other reproductive traits including NFR, FFW, FD, and FL on positive directions and LT treated-39 pepper accessions were clustered into seven groups by the clustering analysis. The selected accessions were primarily involved with the positive trends with the reproductive index including NFR, FL, FD, and FW traits and would be used for pepper breeding programs on developing LT-tolerant cultivars.

(1) Background: Although manual therapy for pain relief has been used as an adjunct in treatments for chronic low back pain (CLBP), there is still the belief that a single session of myofascial release would be effective. This study aimed to investigate whether a single session of a specific technique reduces pain and disability. (2) Methods: This was a crossover clinical trial in which 41 participants over 18 years old with CLBP were randomly enrolled into 3 situations - experimental, placebo, control, in a balanced and cross-over manner. The subjects underwent a single session of myofascial release on thoracolumbar fascia and compare it with the control and placebo. Outcome were pain and functionality, evaluated using the numerical pain rating scale (NPRS), pressure pain threshold (PPT) and Oswestry (ODI). (3) Results: There was no effects between-, within-tests, and interaction for all the outcomes, i.e., NPRS (η 2 = 0.32, F = 0.48, p = 0.61), PPT (η2 = 0.73, F = 2.80, p = 0.06), ODI (η 2 = 0.02, F = 0.02, p = 0.97). (4) Conclusion: A single trial of thoracolumbar myofascial release technique was not enough to reduce pain and disability in subjects with CLBP.

Background: To examine the association between income levels and mortality rates in patients with chronic kidney disease. Methods: We analyzed data obtained from 3,172 patients with chronic kidney disease obtained from the Korean National Health Insurance claims database (2003–2009). Each patient was monitored until December 2010 or until death, whichever came first. Individual income was estimated from the national health insurance premium. Information on mortality was obtained from the Korean National Statistical Office. Cox proportional hazard models were used to compare mortality rates between different income groups after adjusting for possible confounding risk factors. Results: A low income was significantly associated with a high mortality rate after adjusting for covariates (adjusted HR 1.298 [1.082–1.556]). In addition, dialysis patients who had low incomes were more likely to have higher mortality rates compared to those in dialysis patients who had high incomes (adjusted HR 1.528 [1.122–2.082]). Conclusion: The findings of this study indicate that chronic kidney disease patients with low incomes have the highest mortality risk. Promotion of targeted policies and priority health services for patients with low incomes may help reduce the mortality rate in this vulnerable group.

To achieve efficient utilization of low-concentration mine gas, reduce resource waste, and alleviate environmental pollution, high-temperature oxidation of low-concentration gas at a concentration range of 1.00% to 1.50% that is directly discharged into the atmosphere during coal mine production was oxidized to recover heat for reuse. The gas oxidation equipment was improved for the heating process, and the safety of low-concentration gas oxidation under high-temperature environment was evaluated. Experimental results showed that the reactor could provide a 1000 ℃ high-temperature oxidation environment for gas oxidation after installing high-temperature resistant ceramics. The pressure variation curves of the reactor with air and different concentrations of gas were similar. Due to the thermal expansion, the air pressure slightly increased and then returned to normal pressure. In contrast, the low-concentration gas exhibited a stable pressure response in the high-temperature environment of 1000 ℃. The outlet pressure was significantly greater than the inlet pressure, and the pressure difference between the inlet and outlet exhibited a trend to increase with the gas concentration. The explosion limit varied with the temperature and the blend with oxidation products. The ratio of measured gas pressure to air pressure after oxidation was below the explosion criterion, indicating that the measured concentration gas is still safe after the shift of explosion limit, which provides a safe concentration range for efficient use of low-concentration gas in the future.

The establishment of low carbon assessment initiatives is a crucial task especially at the city level. The determination of which source of carbon contributed more require robust data set and strategic approach. Hence, by using the campus as a small city approach, the establishment of carbon assessment and its’ reduction initiatives was required to keep track of the hotspot of the carbon source. The substantial amount of carbon source from campus operations such as energy consumption in the building, waste generation, and water consumption were identified. Moreover, as institutions of higher education, the execution of low carbon campus was initiated structurally involves the triangulation of research activities, teaching & learning and as well as campus operations or known as campus living lab approach. The application of low carbon cities framework, LCCF and assessment system enables to strategize the low carbon campus initiatives through the use of carbon footprint concept and the LCCF carbon track.

This paper deals with a non-contact method to identify the aerodynamic propeller parameters of the Parrot AR.Drone quadrotor. The experimental set consists in a camera recording the vehicle flights, the audio signal is extracted and is used a spectrogram analysis to estimates the propeller velocity. First, the aerial vehicle takes off and starts a hovering maneuver. The experiment is repeated with different additional masses attached to its rigid body. If the weight over the UAV increases/decreases, then the propeller must rotates faster/slower to produce a higher/lower thrust, and consequently, the sound frequency increases/decreases. Finally, this proposition is validated experimentally, and the estimated velocity is used to identify the quadrotor thrust parameters.

Introduction: We investigated the potential effect of smoking on pathological staging in clinically low-risk patients. Material-Methods: Data of 59 patients who were diagnosed with a bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated, retrospectively. A total of 33 patients who currently smoke or smoked were classified as ever smokers group and 26 patients who did not ever smoke were classified as never smokers group. Pathological diagnoses of the patients in both groups were compared. Results: A total of 9 patients (27.3%) in ever smokers group and 18 patients (69.2%) in never smokers group had Ta disease (p<0.05). Morover, 19 patients (57.6%) in ever smokers group and 5 patients (19.2%) in never smokers group had T1 disease (p<0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in ever smoking and never smoking groups, respectively (p<0.05). The number of patients with high grade (HG) tumor were 25 (75.8%) and 7 (26.9%) in ever smoking and never smoking groups, respectively (p<0.05). Ta HG was detected in 9 (27.3%) patients in ever smoking group. In contrast, no patients in never smoking group had Ta HG disease (p<0.05). The number of patients with T1 HG was 17 (51.5%) in ever smoking group and 2 (7.69%) in never smoking group (p<0.05). Conclusion:Smoking seems to associate with pathologically worse stage and grade in patients with primary, single, < 3cm bladder cancer.

AbstractWe investigated the effect of cigarette smoking on pathological staging in clinically low-risk patients. Data of 59 patients who were diagnosed with bladder tumor for the first time and had a single lesion radiologically and endoscopically smaller than 3 cm were investigated retrospectively. 33 patients who smoked were classified as Group I, and 26 patients who did not smoke were classified as Group II. Pathological diagnoses of the patients in both groups were compared. The mean age of the patients were 64.8 (20–86) years. In Group II, 5 (19.2%) were female and 21 (80.8%) were male (p < 0.05). Nine patients (27.3%) in Group I and 18 patients (69.2%) in Group II had Ta disease (p < 0.05). Nineteen patients (57.6%) in Group I and 5 patients (19.2%) in Group II had T₁ disease (p < 0.05). The number of patients with low grade (LG) tumor were 8 (24.2%) and 19 (73.1%) in Group I and in Group II, respectively (p < 0.05). The number of patients with high grade(HG) tumor were 25 (75.8%) and 7 (26.9%) in Group I and in Group II, respectively (p < 0.05). TaHG was detected in 9 (27.3%) patients in Group I. In contrast, no patients in Group II had TaHG disease (p < 0.05). The number of patients with T₁HG was 17(51.5%) patients in Group I and 2 (7.69%) patients in Group II (p < 0.05). Smoking is associated with pathologically HG and stage in patients with first time bladder tumor which is single and smaller than 3 cm.

Background: The prevalence of atopic dermatitis in domestic animals is one of the problems of modern veterinary. Treating with standard techniques using chemotherapeutic agents not always leads to a positive result of therapy; moreover, many drugs produce adverse side effects. Methods: Low level laser therapy, in particular, intravenous laser blood illumination (ILBI) has a pronounced and long-lasting impact on the immune system of animals. The combined technique including ILBI-635 (635 nm, 2 mW, 5 min) and LUVBI^® (365 nm, 2 mW, 3 min) every other day provides a positive change in clinical status of cats with allergic dermatitis after the 3rd-4th treatment session. Results: The increased level of erythrocytes and hemoglobin was identified in the course of treatment, and it indirectly indicates increased blood transport activity, which improves trophic provision and microcirculation. A double reduction of leukocytes and a significant decrease of neutrophil cells indicate the immunomodulatory effect of LILI (low-intensity laser illumination). The increase in the percentage of lymphocytes and the decrease of eosinophils and monocytes against the background of basophil concentrations deviations within physiological concentration result in the reduction of inflammatory mediators expression that induce itching. The reduction of total IgE concentration 32 times against control on the 7th day of treatment correlates with the decrease in the quantitative content of peripheral blood eosinophils, indicating the decrease in severity of an allergic process. Conclusion: LLLT is recommended against the background of standard drug therapy to achieve quick clinical outcome together with a long-lasting prolonged effect.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.

This paper concentrates on the general birth-death processes with two different types of catastrophes. The Laplace transform of transition probability function for birth-death processes with two-type catastrophes are is successfully expressed with the Laplace transform of transition probability function of the birth-death processes without catastrophe. The first effective catastrophe occurrence time is considered. The Laplace transform of its probability density function, expectation and variance are obtained.

Two beneficial characteristics of aircraft generators are having armature windings and PM excitation sources placed on the stator side (maintenance and thermal management) and having a clear-cut rotor without permanent magnets or excitation windings (vulnerable at high speeds due to associated centripetal mechanical stresses). Within this framework, a doubly-salient permanent magnet (DSPM) generator was conceived by optimizing the stator size and rotor structure to minimize the torque ripple and maximize the RMS voltage value per turn of each generator phase. A Multi-Objective Design Strategy based on a 2D finite element analysis was used, being set to have characteristics closest to optimal for a Boeing 767 turbine, that is, the necessary electromotive force for a required power of 90 kW at 3000 rpm, feeding a simplified Boeing 767 electrical power distribution system. The results show that the machine could not deliver the required power at 3000 rpm since the 2D finite elements analysis demonstrates that the 2D model gives optimistic results when compared with the 3D FEM model. However, with a 3D finite element analysis of the machine feeding the aircraft load, it was seen that the machine’s efficiency is 92%, suggesting this machine can be a plausible solution.

The possibility of using graphane monolayer crystals as the electrode material is becoming popular. Graphane is stable at room temperature and has large surface area, but its chemical inertness hinders its direct interactions with Li ions. In this study, we performed density functional theory calculations to study the energetic stability, structural and electronic properties of Li on graphane with various CH divacancy configurations (v12, v13 and v14 ). The results show that adsorption of Li atom reduces the formation energy of the CH divacancy configurations. The Li-v12 is most stable with the highest binding energy of 3.25 eV/Li and relaxes to in-plane with other C atoms. Altering the Li charge state to have Li−1-v12 or Li+1 -v12 affects the energetic stability and electronic characters of Li-v12 . The Li−1-v12 (Li +1-v 12 ) enhances (reduces) the binding force between Li and v 12 configuration, and furthermore it improves (deteriorates) the conductivity of the structure. Further investigation of graphane with vacancies is encouraged due to these intriguing observations, as it holds promise for potential utilization as an electrode material.

In the natural environment, sand accumulation and desertification can influence the efficiency of photovoltaic arrays. In this study, PV module output characteristics were examined under different sand particle size, varying sand densities and inclination angles, and at wind speeds of 5m/s, 10m/s, and 15m/s. Both theoretical and experimental results showed that the output power of the module declines with increasing sand density. As the sand particle size increases, the module maximum output power rises and then stabilizes. The two control variables, namely sand density and sand particle size, influence the module temperature and light transmittance distinctly. Contrary to the impact of sand density on the module filling factor curve, the module filling factor exhibits varying trends under different sand particle sizes. Additionally, the pattern of the module filling factor as a function of sand density contrasts with that of the module temperature under analogous conditions. Specifically, when the sand density on the PV module surface increases from 0 to 40g/m², there is a 32.2% reduction in maximum output power. At a wind speed of 15m/s, this reduction was found consistent across all wind speed categories. Furthermore, the trend of the module filling factor rel-ative to sand accumulation density contrasts with the module temperature trend under analogous conditions. Notably, the filling factor reached its apex at a sand accumulation density of 35g/m², which corresponded to the module temperature's nadir during the experiment.

This study examines the wind shear coefficient (WSC) values at three coastal wind sites located in the southern region of Balochistan, Pakistan: Pasni, Ormara, and Jiwani. These WSC values were obtained using 10-minute measured wind speed data at heights of 20, 40, and 60 meters above ground level (AGL). Since wind measurements are typically recorded at lower heights due to cost and resource constraints, extrapolation techniques were employed to estimate wind speeds at higher altitudes. However, using a constant WSC value for extrapolation may lead to significant errors between extrapolated and actual wind speed measurements, impacting the energy output of wind turbines. To evaluate the effect of WSC on energy yield, the study employed power curves and frequency distributions for 2MW and 1.5MW wind turbines. Additionally, wind power density was calculated using air density derived from measured air temperature and surface pressure data, covering two years period from November 2016 to August 2018. The overall mean WSC values were found to be 0.076 at Pasni, 0.094 at Jiwani, and 0.053 at Ormara. The study further investigated the seasonal, monthly, and diurnal variations of WSC. For assessing wind resources at a height of 60m, the study utilized Wind Roses, wind power density, and Weibull parameters. Comparing the actual WSC values presented in this paper with those obtained using the 1/7 power law and measured data at 60m AGL, the energy yield from the wind turbines showed reduced output and capacity factor.

The general-purpose Compact Muon Solenoid (CMS) detector at the Large Hadron Collider (LHC) at CERN includes the hadronic calorimeter to register the energies of the charged and neutral hadrons produced in the proton-proton collisions at the LHC at a center of mass energy 13.6 TeV. The calorimeter is located inside the superconducting solenoid of 6 m in diameter and 12.5 m in length creating the central magnetic flux density of 3.8 T. For operating optimally in the high pileup and high radiation environment of the High Luminosity LHC, the existing CMS endcap calorimeters will be replaced with a new high granularity calorimeter (HGCal) comprising of an electromagnetic and a hadronic section in each of the two endcaps. The hadronic section of the HGCAL will include 44 stainless steel absorber plates with a relative permeability value well below 1.05. The volume occupied by 22 plates in each endcap is about 21 m3. The calculation of the axial electromagnetic forces on the absorber plates is a crucial element in designing the mechanical construction of the device. With a three-dimensional computer model of the CMS magnet, the axial forces on each absorber plate are calculated and the dependence of forces on the central magnetic flux density value is presented. The method of calculation and the obtained results are discussed.

Articular cartilage lacks intrinsic regenerative capabilities, and the current treatments fail to regenerate damaged tissue and lead only to temporary pain relief. These limitations have prompted the development of tissue engineering approaches, including 3D culture systems. Thanks to their regenerative properties and capacity to recapitulate embryonic processes, spheroids obtained from mesenchymal stromal cells are increasingly studied as building blocks to obtain functional tissues. The aim of this study was to investigate the capacity of adipose stromal cells to assemble in spheroids and differentiate toward chondrogenic lineage from the perspective of cartilage repair. Spheroids were generated by two different methods (3D chips vs Ultra-Low Attachment plates), differentiated toward chondrogenic lineage, and their properties were investigated by: molecular biology analyses, biophysical measurement of mass density, weight, and size of spheroids, and confocal imaging. Overall, spheroids showed the ability to differentiate by expressing specific cartilaginous markers that correlate with their mass density, defining a critical point at which they start to mature. Considering the spheroid generation method, this pilot study suggested that spheroids obtained with chips are a promising tool for the generation of cartilage organoids that could be used for preclinical/clinical approaches, including the realization of personalized therapy.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

Nonparametric density estimation for nonnegative data is considered in a situation where a random sample is not directly available but the data are instead observed from the length-biased sampling. Due to the boundary bias problem of the location-scale kernel, the approach in this paper is an application of asymmetric kernel. Two nonparametric density estimators are proposed. The mean integrated squared error, strong consistency, and asymptotic normality of the estimators are investigated. Some simulations illustrate the finite sample performance of the estimators.

Voids in face-centered cubic (fcc) metals are commonly assumed to form by the aggregation of vacancies; however, the mechanisms of vacancy clustering and diffusion are not fully understood. In this study, we use computational modeling to provide a detailed insight into the structures and formation energies of primary vacancy clusters, mechanisms and barriers for their migration in bulk copper, and how these properties are affected at simple grain boundaries. The calculations were carried out using Embedded Atom Method (EAM) potentials and Density Functional Theory (DFT) and employed the Site-Occupation Disorder code (SOD), the Activation Relaxation Technique nouveau (ARTn) and the Knowledge Led Master Code (KLMC). We investigate stable structures and migration paths and barriers for clusters of up to six vacancies. Migration of vacancy clusters occurs via hops of individual constituent vacancies with di-vacancies having a significantly smaller migration barrier than mono-vacancies and other clusters. This barrier is further reduced when di-vacancies interact with grain boundaries. This interaction leads to the formation of self-interstitial atoms and introduces significant changes into the boundary structure. Tetra-, penta-, and hexa-vacancy clusters exhibit increasingly complex migration paths and higher barriers than smaller clusters. Finally, the direct comparison with the DFT results shows that EAM can accurately describe the vacancy-induced relaxation effects in the Cu bulk and in grain boundaries. Significant discrepancies between the two methods were found in structures with a higher number of low-coordinated atoms, such as penta-vacancies and di-vacancy absortion by grain boundary. These results will be useful for modeling the mechanisms of diffusion of complex defect structures and provide further insights into the structural evolution of metal films under thermal and mechanical stress.

The electrochemical CO2 reduction reaction can lead to high value-added molecules production while helping decrease anthropogenic CO2 emissions. Copper can reduce CO2 to more than thirty different hydrocarbons and oxygenates, but it lacks the required selectivity. We present a computational investigation of the role of nano-structuring and alloying in Cu-based catalysts on the activity and selectivity of CO2 reduction to one-carbon products: carbon monoxide, formic acid, formaldehyde, methanol, and methane. The adsorption, activation, and conversion of CO2 were computed on monometallic and bimetallic (decorated and core-shell) 55-atom Cu-based clusters. The dopant metals considered were Ag, Cd, Pd, Pt, and Zn, located at different coordination sites. The relative binding strength of the intermediates at different applied potentials were used to identify the optimal catalyst for the selective CO2 conversion to one carbon products. It was discovered that single atom doping with Cd and Zn is optimal for the CO2 to carbon monoxide conversion. The core-shell models with Ag, Pd, and Pt provided higher selectivity for formic acid and formaldehyde. The Cu-Pt and Cu-Pd showed lowest overpotential for methane formation.

Martensitic steels are used at a wide range of strength levels in environments which expose them to hydrogen or water vapor over a large range of partial pressures and temperatures. Hydrogen can cause catastrophic failures under many seemingly benign conditions. The effect of hydrogen on the dimension stability of high strength martensitic steels under such conditions has been poorly understood, and existing models do not seem to adequately account for it. Experiments were conducted to measure the variation in volume due to the uptake of hydrogen of such steels under near-ambient conditions, and the results were compared to theoretical estimates derived from the density of defects acting as hydrogen traps. Based on these results a new model for hydrogen embrittlement was developed. The hydrogen lattice dilation (HLD) model isolates volume expansion as a primary driver of hydrogen embrittlement. It provides and distinguishes two modes of failure acceleration: the fast, brittle, stress-intensity independent cracking under higher static crack loading, and a slower, highly stress-intensity dependent tearing mode at lower stress intensity. The relationship between the two is explained, as is how hydrogen absorption by defects accounts for the crack threshold and crack velocity of each.

Research have been conducted in many countries around the world to assess air quality during COVID-19 pandemic, especially during lockdown period, some of these studies found an increase or decrease in some pollutants. This paper investigates the impact of COVID-19 on seven air pollutants (i.e., PM_2.5, PM₁₀, NO₂, O₃, SO₂, H₂S, CO) from the period January 2020 to December 2020 in the State of Kuwait. Kuwait is a desert country located in the north-eastern part of the Arabian Peninsula, and the northeast of the Arabian Gulf (Persian as it is sometimes called). Several analytical methods were conducted, such as spatial analysis (spatial interpolation) to study the distribution of the studied variables. The data was also statistically analysed (time series analysis - Kernel density) to study the temporal changes. The analysis also included applying air quality index to the data. We found that concentrations for the pollutants decreased during the pandemic due to the decrease of anthropogenic sources including such as traffic and petroleum activities, but the concentration for PM_2.5 increased, mostly because of the transported dust coming with the northwest winds prevailing in Kuwait from the Arabian deserts and Iraq.

Cesiumtrifluoroacetate (CsTFA) is a key chemical for RNA-based stable isotope analyses to link the structure and function of microbial communities. We report a protocol to easily synthesize CsTFA from Cesiumcarbonate (Cs₂CO₃₎ and Trifluoroacetate (TFA) and show that self-synthesized CsTFA behaves similar to commercial CsTFA in the separation of isotopically labelled and unlabelled E. coli RNA.

Background: This study aims to investigate the effects of visual neurofeedback stimulation on the brain activity in overweight cases. The neuroscience studies indicated the personal decision about eating under the impact of environmental factors such as (visually, smelling, tasting) is related to neural activity of the prefrontal lobe of the brain. Therefore, there were many attempts to modify the food intake behavior in overweight cases through the stimulation of the prefrontal cortex. However, the empirical viewing of EEG-neurofeedback experiments has not explicated the details about the effect of the EEG-NF, the specificity of positive treatment effects remains in a challenging scope.Methods: This study is a cue-exposure EEG-NF experiment to verify the hypothesis of effecting the EEG-NF on the electrical activity of PFC and modifying the general symptoms of food intake behavior in overweight cases. Twenty-four individuals were recruited as participants for this study. These participants were assigned randomly into two groups; the EX-Group (N=12) enrolled in 8 sessions of the EEG-NF experiment, and the C-Group (N=12) was listed in no EEG-NF sessions. The participants provided researchers with a self-report questionnaire relating to their observation of general symptoms of food intake behavior, and EEG signals recordings into the pre and posts stimulation phase. The power spectral density (PSD) method was applied for EEG parameters extraction.Results: The results of a two-way analysis of variance (ANOVA) explained that a significant variation in variables between the two groups after the EEG-NF experiment. The analysis of the quantitative variables indicated that the effect of EEG-NF experiment was a significant decrement in EEG power bands which significantly influenced changing the median of self-report questionnaire responses that is related to general symptoms of food intake behavior.Conclusions: This study provides preliminary support for the therapeutic potential of EEG-NF experiment that targets the prefrontal cortex, to influence neural processes underlying food intake behavior in overweight cases.

Maize (Zea mays L.) production in West and Central Africa is constrained by drought, low soil-N and Striga infestation. Breeders in the region have developed and commercialized extra-early and early-maturing hybrids (E-EH and EH), which combine high yield potentials with tolerance/resistance to the three stresses. Hybrids of both maturity groups are new to the farmers; thus, the urgent need to recommend appropriate agronomic practices for these hybrids. We investigated the responses of four hybrids belonging to extra-early and early-maturity groups to plant density (PD) and nitrogen (N) application in five agroecologies. The EHs consistently out-yielded the E-EHs in all the five agroecologies. The hybrids showed no response to N-fertilizer application above 90 kg ha-1. All interactions involving N had no significant effect on all traits except in few cases. The E-EHs and EHs had similar response to PD; their grain yield decreased as PD increased. Contrarily, flowering was delayed and expression of some other agronomic traits such as plant and ear aspects became poorer with increased PD. Optimal yield was obtained at approximately 90 kg N ha-1 and 66,666 plants ha-1. Most of the measured traits indicated high repeatability estimates (i.e. ≥ 60) across the N levels, PDs and environments. Evidently, the hybrids were intolerant of high PD.

Binder jet printed components typically have low overall density in the green state and high shrinkage and deformation after heat treatment. It has previously been demonstrated that, by including nanoparticles of the same material in the binder, these properties can be improved as the nanoparticles can fill the interstices and pore throats between the bed particles. The beneficial effects from using these additive binder particles can be improved by maximising the binder particle size, enabling the space within the powder bed to be filled with a higher packing efficiency. The selection of maximum particle size for a binder requires detailed knowledge of the pores and pore throats between the powder bed particles. In this paper, a raindrop model is developed to determine the critical radius at which binder particles can pass between pores and penetrate the bed. The model is validated against helium pycnometry measurements and binder particle drop tests. It is found that the critical radius can be predicted, with acceptable accuracy, using a linear function of the mean and standard deviation of the particle radii. Percolation theory concepts have been employed in order to generalise the results for powder beds that have different mean particle sizes and size distributions. The results of this work can be employed to inform the selection of particle sizes required for binder formulations, to optimise density and reduce shrinkage in printed binder jet components.

Nicotine is a pharmacologically active component of tobacco which adversely affects the male reproductive system and fertility and Icariin (ICA) is the main active ingredient of Epimedium herba which has been used to treat several male reproductive problems. This study was aimed at investigating the protective or ameliorative effect of ICA against reproductive toxicity induced by intraperitoneal injection of nicotine in mice. Forty male mice were randomly divided into 4 groups: control, nicotine (0.75 mg/kg intraperitoneally), icariin (ICA, 75 mg/kg), and icariin plus nicotine (ICA + nicotine) group. After 35 days of treatment, the mice were weighed, sacrificed, and their reproductive organs were collected and examined for further studies. In the nicotine-treated group, epididymal sperm density and serum testosterone concentrations significantly decreased relative to the control group. Nicotine also caused oxidative damage as shown by significant reduction in the activities of antioxidant enzymes and an elevation in Malondialdehyde (MDA) levels. Icariin on the other hand, improved the reduction in sperm characteristics, hormone levels, and activities of antioxidant enzymes alterations observed in the nicotine treated mice. These findings indicate that the nicotine-induced reproductive toxicity and oxidative damages on male reproductive tissues can be effectively attenuated by icariin.

The objective of this study was to determine the association of physiological responses and root distribution patterns on yield of the second ratoon cane and the relationships among these traits. Seventeen sugarcane genotypes were planted in a randomized complete block design with four replications. The second ratoon crop was evaluated for germination percentage, cane yield, SPAD chlorophyll meter reading (SCMR), chlorophyll fluorescence, relative water content (RWC), specific leaf area (SLA) and stomatal conductance. Root length density (RLD) was evaluated by auger method. The root samples were divided into upper soil layer and lowers soil layers to study root distribution patterns. Sugarcane genotypes were significantly different for RLD, germination percentage and cane yield. Root distribution patterns were classified into three groups based on the RLD. High RLD between plants in the upper soil layers at 90 DAH was positively correlated with high germination, whereas high RLD between rows in the lower soil layers at 90 and 270 DAH was associated with high cane yield. RWC at 90 DAH and stomatal conductance at 180 DAH were closely related to germination percentage, whereas chlorophyll fluorescence and stomatal conductance at 180 DAH were closely related to cane yield.

The relative dislocation density of aluminum and copper samples is quantitatively measured using linear Resonant Ultrasound Spectroscopy (RUS). For each metallic group, four samples were prepared with different thermomechanical treatments in order to induce changes in their dislocation densities. The RUS results are compared with Nonlinear Resonant Ultrasound Spectroscopy (NRUS) as well as Second Harmonic Generation (SHG) measurements. NRUS has a higher sensitivity by a factor of two to six and SHG by 14% to 62%. The latter technique is, however, faster and simpler. As main a result we obtain a quantitative relation between the changes in the nonlinear parameters and the dislocation density variations, which in a first approximation is a linear relation between these differences. We also present a simple theoretical expression that explains the better sensitivity to dislocation content of the nonlinear parameters with respect to the linear ones. X-Ray diffraction measurements, although intrusive and less accurate, support the acoustics results.

β-dicalcium silicate (β-Ca₂SiO₄, or β-C₂S in cement chemistry notation) is one of the most important minerals in cement. An improvement of its hydration rate would be the key point for developing environmentally friendly cements with lower energy consumption and CO₂ emissions. However, there is a lack of fundamental understanding on the water/β-C₂S surface interactions. In this work we aim to evaluate the water adsorption on three β-C₂S surfaces at the atomic scale using density functional theory (DFT) calculations. Our results indicate that thermodynamically favorable water adsorption takes place in several surface sites, with a broad range of adsorption energies (−0.78 to −1.48 eV), depending on the particular mineral surface and adsorption site. To clarify the key factor governing the adsorption, the electronic properties of water at the surface were analyzed. The partial density of states (DOS), charge analysis, and electron density difference analyses suggest a dual interaction of water with β-C₂S (100) surface: a nucleophilic interaction of the water oxygen lone pair with surface calcium atoms, and an electrophilic interaction (hydrogen bond) of one water hydrogen with surface oxygen atoms. Despite the elucidation of the adsorption mechanism, no correlation was found between the electronic structure and the adsorption energies.

In mega cities such as Seoul in South Korea, it is very important to protect the city from the flooding even for the short time of period due to the enormous amount of economic damage. In impervious area of the city, stormwater pipe network is commonly applied to discharge rainfall to the outside of catchment. Therefore, the stormwater pipe network in urban catchment should be carefully designed to discharge the runoff quickly and efficiently. In this study, different types of structures in stormwater pipe network were evaluated using the relationship between the peaks rainfall and runoff in urban catchments in South Korea. More than 400 historical rainfall events were applied in five urban catchments to estimate peak runoff from different type of network structures. Linear regression analysis was implemented to estimate peak runoffs. The coefficient of determination of the regressions were higher than 0.9 which means the regression model represent very well the relationship between the two peaks. However, the variation of the prediction becomes large as the peak rainfall increases and the variation become even larger when the network structure is branched. Therefore, it depends on the structure of stormwater pipe network. When the water paths in the pipe network is unique (branched network), the increased amount of rainfall is congested around the rainwater inlets and the uncertainty of peak runoff prediction is increased. If there are many possible water paths depending on the amount of discharge (looped network), the increased rainfall is discharged more quickly through the many water paths. This can be a way to represent the reliability of the stormwater pipe network. The structures of stormwater pipe network is evaluated using drainage density which is the length of pipes over the unit catchment area and 95% confidence interval. As a result, the 95% confidence interval is increased as the drainage density is increased because the accuracy of peak runoff prediction is decreased. As mentioned earlier, because the looped networks have many alternative water flowing paths, elimination time of rainfall from the catchments become short, the 95% confidence interval become narrow, and the reliability of peak runoff prediction become high. Therefore, it is beneficial to install looped stormwater pipe network within the affordable budget. It is important factor to determine the amount of complexity in stormwater pipe network to decrease the risk of urban flooding.

Novel high energy density materials N14 (1,6-dihydro-1,2,3,3a,4,5,5a,6,7,8,8a,9,10,10a-tetradecazapyrene) and N18 (1,2,2a,3,4,4a,5,6,6a,7,8,8a,9,10,10a,11,12a-octadecazacoronene) were designed, and their structures, detonation performance and stabilities were calculated employing density functional theory (DFT). Calculations reveals that they have a good balance between high energy and stability. Their energy gaps between LUMO and HOMO are all lower than that of TATB, while their impact sensitivity h_50% is estimated close to that of RDX. Concerning energy, detonation performance of the N14 (P = 43.6 GPa, D = 10040 m/s, Q = 2214 cal/g) and the N18 (P = 37.4 GPa, D = 9400 m/s, Q = 2114 cal/g) are comparable to CL-20.

Deadwood represents a source of nutrients, carbon and water for metabolism within forest ecosystem. Nutrients are mobilized due to the decomposition of wood, which is a long-term process that can be best studied by analysing environmental data on a temporary scale. Our study provides physico-temporal data on the downed logs of three major tree species in European temperate forests: Abies alba Mill., Fagus sylvatica L. and Picea abies (L.) Karst. Time since death was obtained using tree censuses (repeated for 40 years) and dendrochronology for each single downed log, the oldest being 75 years old. Standard laboratory methods were used for the determination of wood density and moisture changes. F. sylvatica was decomposed rapidly in the initial phase – mass loss was 50% during the 5 years after death, while A. alba and P. abies lost 13% and 16%, respectively. Downed logs of F. sylvatica contained 391 kg of water per m³, while these of P. abies 279 kg. A log-transformed linear model was created that shows the dependence of time since death on mass loss. According to the model, F. sylvatica had the shortest total decomposition time (39 years), followed by A. alba (58 years) and P. abies (86 years).

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Hyper-radiosensitivity (HRS) is the increased sensitivity to low doses of ionizing radiation observed in most cell lines. We previously demonstrated that HRS is permanently abolished in cells irradiated at a low dose rate (LDR), in a mechanism dependent on transforming growth factor β3 (TGF-β3). In this study, we aimed to elucidate the activation and receptor binding of TGF-β3 in this mechanism. T-47D cells were pre-treated with inhibitors of potential receptors and activators of TGF-β3, along with addition of small extracellular vesicles (sEVs) from LDR primed cells, before their radiosensitivity was assessed by the clonogenic assay. The protein content of sEVs from LDR primed cells was analyzed with mass spectrometry. Our results show that sEVs contain TGF-β3 regardless of priming status, but only sEVs from LDR primed cells remove HRS in reporter cells. Inhibition of the matrix metalloproteinase (MMP) family prevents removal of HRS, suggesting an MMP-dependent activation of TGF-β3 in the LDR primed cells. We demonstrate a functional interaction between TGF-β3 and activin receptor like kinase 1 (ALK1), by showing that TGF-β3 removes HRS through ALK1 binding, independent of ALK5 and TGF-βRII. These results are an important contribution to a more comprehensive understanding of the mechanism behind TGF-β3 mediated removal of HRS.

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

With the widespread use of new equipment such as distributed photovoltaics, distributed energy storage, electric vehicles, and distributed wind power, the control of low-voltage distribution networks (LVDNs) has become increasingly complex. Acquiring the most recent topological structure is essential for conducting accurate analysis and real-time control of LVDNs. The signal-injection-based topology identification algorithm is favored for its speed and efficiency. This study proposes a new signal-injection-based topology identification algorithm aimed at solving the issues of reduced completeness and correctness of identification caused by missing feature signal records (FSRs). By analyzing the correlations between FSRs of different positions, the algorithm employs vertical and horizontal completion methods to effectively address missing data, combined with inclusion detection algorithms, to identify the topology of LVDNs. Based on the study of actual LVDN data, the results indicate that the algorithm not only significantly improves the completeness and correctness of topology identification for LVDNs but can also increase the number of devices in operation by evaluating the status of topological equipment, further enhancing the topology identification performance.

In the process of climate change mitigation and adaptation, the focus on climate risk driven by transition innovations has received widespread attention from governments, regulators, and investors. Based on the identification of low-carbon patents through the Green and Low-carbon Technology Inventory in China, this study constructs low-carbon innovation measurements of listed firms in China from 2015 to 2021. Then, an empirical model is used to investigate the impact and mechanism of climate transition innovations on the default risk. The baseline regression model shows that low-carbon innovations can mitigate the default risk of listed firms. Moreover, our findings are supported by instrumental variable regressions that use the time costs of innovation. Finally, the mediation effect demonstrates that investor attention, total factor productivity, and technology spillovers are paths through which transition innovations can affect the default risk. This study reveals that low-carbon technological advances have a positive effect on climate transition risks.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Public housing stock, called Social Housing, in Italy developed between the 1950s and the 1980s. As of today, the first residential developments are almost nearing their end-of-life age, in need of urgent and intensive renovation. The European Commission, with the Renovation Wave, has set a goal of doubling the rate of building renovation over the next 10 years, reducing emissions, improving energy performance, and promoting decarburization. Renovation interventions, including structural, functional, energy, plant upgrading, etc., are to be preferred over integral demolition and reconstruction interventions, which have significant repercussions in terms of managerial and social discomfort. The case studies examined concern renovation interventions aimed at energy efficiency, functional adaptation of housing as well as facade restyling. The design variants analyzed were evaluated in terms of CO2e emissions, according to LCI (Life Cycle Inventory) and EPD (Environmental Product Declaration) approaches. This approach has a twofold purpose: to propose design guidelines, with low CO2e emissions, through hypotheses of variants to the case studies, and to propose, to the Economic Operators, economically advantageous bidding scenarios, in the procurement process.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Background. Implementing mammogram screening means that clinicians are seeing many breast cancers that will never develop metastases. The purpose of this study was to identify subgroups of breast cancer patients who did not present events related to long-term breast cancer mortality, taking into account diagnosis at breast screening, absence of palpability and axillary involvement, and genomic analysis with PAM50. Patients and Methods. To identify them, a retrospective observational study was carried out selecting patients without palpable tumour, without axillary involvement, and a genomic analysis was performed with PAM50. Results. The probability of distant metastasis-free interval (DMFI) of 337 patients was 0.92 (95% CI, 0.90-0.93) at 20 years and 0.96 (95% CI, 0.92-1.00) in 95 patients (28%) with available PAM50 tests. In 22 (23.15%) luminal A tumours and in 9 (9.47%) luminal B tumours smaller than 1 cm and in HER2 and basal type tumours there were no metastatic events (20-year DMFI of 1.00). Conclusion. Patients with nonpalpable breast cancer found at screening with negative nodes are at very low risk. It is possible to identify subgroups without metastatic events by determining the intrinsic subtype and tumour size less than 1 cm. De-escalation of treatment should be considered.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

forging a resilient path towards a low carbon future, this research delves deep into the intricate dynamics of the petroleum and petrochemical industries. By uncovering the challenges posed by transitioning to a low carbon economy, this study emphasizes their transformative potential as catalysts for growth. Through an in-depth analysis of the oil and natural gas sector, it not only sheds light on the carbon footprint of Nigeria's petroleum and petrochemical industries but also identifies the opportunities for sustainable transformation within these sectors. Ultimately, this research aims to pave the way for a greener future by unraveling the complexities and intricacies of building a low carbon economy."By incorporating the unique attributes of the petroleum and petrochemical industries and considering the evolving domestic and global context, this research investigates the challenges and prospects associated with the shift towards a low-carbon economy. It delves deep into the complexities of the sector, taking into consideration the distinct characteristics of petroleum and petrochemical production. Through a comprehensive analysis, this study aims to uncover the potential barriers and opportunities that arise from the pursuit of a sustainable and low-carbon future within the petroleum and petrochemical industries. In addition, this research thoroughly examines the current global and local conditions, shedding light on the opportunities for growth and transformation within the petroleum and petrochemical sectors. By presenting insightful perspectives and recommendations, the study aims to provide valuable guidance for fostering the development of a low-carbon economy within these industries. Ultimately, the research seeks to drive positive change by offering actionable insights and strategies to propel the transition towards a sustainable future.

Background. The purpose of the study was to evaluate the intensity and frequency of low back pain (LBP) in people with multiple sclerosis (PwMS) and the patient's knowledge of physiotherapeutic methods of combating. Methods. In this study, patients with confirmed multiple sclerosis were selected. The study was carried out using an original survey questionnaire and a numerical pain intensity scale (Visual Analogue Scale). PwMS were divided into 3 age groups: 18-30 years, 31-50 years, and over 50 years. Results. Ninety PwMS (68 women and 22 men) aged 18 to 60 years were included in the study. The mean duration of the disease was 9.5±4.9 years, and the mean EDSS was 3.5±1.6. Most of the patients had a relapse-remitting form. 68.9% of PwMS felt lower back pain (n = 62). The relationship tested was statistically significant (p=0.0000012), and the strength of the relationship was high (rc=0.695). The average level of low back pain among PwMS was 4.7 out of 10 on the VAS scale. The prevalence of LBP was higher in female patients (p<0.001), with a secondary progressive form (p<0.001) and with a longer duration of the disease (p=0.023). The most widely used methods of LBP therapy were kinesitherapy and manual therapy. Conclusions. LBP is common in multiple sclerosis. A female sex, a secondary progressive form of MS, and a longer duration of the disease increased the risk of LBP. It is important to implement properly planned physiotherapy activities and educate patients on how to combat LBP.

Camera malfunctions or loss of storage elements in imaging devices may lead to loss of important image information or random impulse noise interference. Low rank is one of the important prior information in image optimization processing. This paper uses different low-rank constraint models of the image matrices to recover the impulse interference satellite images. Firstly, an overview of image inpainting models based on nuclear norm, truncated nuclear norm, weighted nuclear norm, and matrix-factorization-based F-norm is presented, and corresponding optimiza-tion iterative algorithms are provided. Then, we conducted experiments under three types of pulse interference and provided visual and numerical results. Finally, it is concluded that the WSVT_ADMM method based on the weighted nuclear norm can obtain the best image inpainting results; The UV_ADMM method based on F norm of matrix factorization has the least computa-tion time and can be used for large-scale low-rank matrix computation; The WSVT_ADMM method based on weighted nuclear norm and the TSVT_ ADMM method based on truncated nuclear norms can significantly improve the repair effect compared to the nuclear norm-based methods such as SVT, SVP, and n_ADMM.

In the context of post-harvest pest management in agricultural products, the adoption of modified atmospheres presents an eco-friendly alternative to conventional pesticides. This study focuses on nitrogen gas as a potential agent for insect control in stored commodities, utilizing computational simulations to investigate its penetration and distribution within two common storage configurations: chamber-contained pallets and silos. By employing the convection-diffusion equation, the simulations reveal insights into nitrogen distribution dynamics and duration required for oxygen reduction. The results highlight the influence of boundary conditions, commodity porosity, and convection effects on nitrogen dispersion. In chamber scenarios, boundary condition type significantly affects oxygen reduction time, while in silos, convection and diffusion interact to establish a consistent diffusion layer thickness. This research enhances the understanding of modified atmosphere techniques and their potential for sustainable pest management. It provides practitioners with valuable quantitative insights, paving the way for optimized modified atmosphere strategies in real-world agricultural contexts.

A Gem-quality rubies and sapphires are often commercially heat treated at about 800°C or higher temperatures to enhance their colour and clarity, and hence quality. For this study, selected corundum samples containing diaspore- and goethite inclusions were heated step-by-step to a maximum of 1000 °C with the aim to monitor the dehydration and phase transformation of these oxyhydroxides to corundum and hematite during heating. Based on our experiments and in agreement with literature, the dehydration of diaspore in corundum occurs between 525 to 550 °C, whereas goethite transforms to hematite already between 300 and 325 °C. As both, diaspore and goethite are common inclusions in rubies, sapphires, and other corundum varieties, these dehydration reactions and phase transformations can be considered important criteria to separate unheated stones from heated ones, specifically in cases in which other methods (e.g. microscopy, FTIR) are unsuccessful.

Torulaspora delbrueckii showed renewed interest in recent years in the fermentation of wine, for its biotechnological potential linked to the ability to enhance flavor and aroma and it probably is the non-Saccharomyces yeast currently widely used in winemaking. On the base of this, sequential fermentations with a selected native strain of T. delbrueckii (DiSVA 130) and low sulfite native strain of Saccharomyces cerevisiae (DiSVA 709) were carried out to establish their contribution in biocontrol and aroma profile. A first set trials, carried out in winery, were set up to establish the effect of the sulfur dioxide addition on pure and T. debrueckii/S. cerevisiae sequential fermentations. A second set of sequential fermentations without SO₂ addition were conducted in the same conditions, to evaluate the biocontrol and aromatic effectiveness of the T. delbrueckii native strain and a commercial one. The effective biocontrol action of native T. delbrueckii inoculated in sequential fermentation was shown, indeed without SO₂ addition the presence of native T. delbrueckii revealed an effective fungistatic action in the first two days of fermentation. Moreover, the native T. delbrueckii strain seems to have fermentative performances comparable to those of T. delbrueckii commercial strain showing a more evident biocontrol action (wild yeasts reduced by c.a. 1 Log at 2^nd day) and its presence did not negatively affect S. cerevisiae fermentation activity. Finally, the combination of both native and commercial T. delbrueckii/S. cerevisiae trials led distinctive aromatic profile of wines with a significant enhancement of isoamyl acetate, phenyl ethyl acetate, supported by positive appreciations, from the tasters, for ripe and tropical fruits, citrus and balance. The whole results indicate that the proposed strain could be a potential biocontrol tool toward wild yeasts in the first phase of fermentation also contributing to improve and differentiate the final aroma wine.

Highly efficient, broadband and distinctively structured electromagnetic wave (EMW) absorption materials exhibit huge exceptions with multi-functions in both military and civilian fields. Searching the relationship between structural and EMW performance is beneficial to develop outstanding microwave absorption materials, and has become an attractive research topic. In this study, we briefly reviewed the different EMW absorption mechanisms and key influence factors, then, present the latest developments in low-dimensional (LD) EMW absorption materials. We provide a comprehensive discussion of remarkable examples and summarize the main information related to the structure-function relationship of dimensional design and structural engineering in order to facilitate the rapid evolution of this fascinating field.

Low back pain (LBP) is a health problem that affects 70-80% of the population in Western countries. Because of the biomechanical relationship between the lumbar region and the hip, it is thought that strengthening the muscles of this joint could improve the symptoms of people with LBP. The objective of the study is to evaluate the current evidence on the efficacy of hip strengthening exercises to reduce pain and disability in people with LBP. Clinical trials were collected from PubMed, PEDro, and Scopus databases published up to September 2022. Based on Preferred Reporting Items for Systematic Review and Meta-Analysis (PRISMA) guidelines and using CASpe and PEDro tools for methodological quality assessment, we selected studies that included hip strengthening exercises as part of LBP treatment and measured pain and/or disability parameters. Among the 966 records identified in the search, a total of 7 studies met the established selection criteria. Overall, participants who performed hip strengthening exercises had significantly improved in pain and disability. The methodological quality of the included studies was assessed as “good”. In conclusion, the addition of hip muscle strengthening exercises iterating LBP effectively improving pain and disability.

Our understanding of the long-term consequences of chronic ionising radiation for living organisms remains scarce. Modern molecular biology techniques are helpful tools for researching pollutant effects on biota. To reveal the molecular phenotype of plants growing under chronic radiation exposure, we sampled Vicia cracca L. plants in the Chernobyl Exclusion Zone and in areas with normal radiation backgrounds. We performed a detailed analysis of soil and gene expression patterns, and made coordinated multi-omics analyses of plant samples, including transcriptomics, proteomics, and metabolomics. Chronic exposure to ionising radiation induced complex and multidirectional changes, including significant alterations in the metabolism and gene expression patterns of irradiated plants. We revealed profound changes in carbon metabolism, nitrogen reallocation, and photosynthesis. These plants were characterised by increased DNA damage, redox imbalance, and stress response reactions. The upregulation of histones, chaperones, peroxidases, and secondary metabolism were noted.

Drowning is a serious public health concern. Low middle income countries are mostly affected, as they carry 90% of the global drowning burden. The purpose of this epidemiological study is to provide a comprehensive overview of fatal drownings in South Africa between 2016 and 2021. The data used for the study was obtained from the South African Police Service. Descriptive statistics were used to summarise data. Statistical analysis included a t-test and chi-square test. The results indicate that the average fatal drownings per annum is 1477 in South Africa, with a drowning rate of 2.54 per 100 000 population from 2016 - 2021. The KwaZulu-Natal province had the highest incidence of drowning. The 0 – 4-year category has a high prevalence of drowning amongst all the age categories. More males drowned in South Africa compared to females. The study highlights key areas of concern these include age, sex, race, province, type of water body and time of day. This information is crucial to inform drowning prevention initiatives in South Africa.

Low-grade glioma (LGG) is a highly aggressive disease in the skull. On the other hand, anoikis, a specific form of cell death induced by the loss of cell contact with the extracellular matrix, plays a key role in cancer metastasis. In this study，anoikis-related genes (ANRGs) were used to identify LGG subtypes and to construct a prognostic model for LGG patients. In addition, we explored the immune microenvironment and enrichment pathways between different subtypes. We constructed an anoikis-related gene signature using the TCGA cohort and investigated the differences in clinical features, mutational landscape, immune cell infiltration, etc. between different risk groups. Kaplan-Meier analysis showed that the characteristics of ANRGs in the high-risk group were associated with poor prognosis in LGG patients. The risk score was identified as an independent prognostic factor. The high-risk group had higher immune cell infiltration, tumor mutation load, immune checkpoint gene expression, and ICB treatment response. Functional analysis showed that these high- and low-risk groups had different immune statuses and drug sensitivity. Risk scores were used together with LGG clinicopathological features to construct a nomogram, and DCA analysis showed that the model could enable patients to benefit from clinical treatment strategies.

Reduced glutathione (GSH) is an antioxidant in plants and is one of the important ways for plants to combat low-temperature stress. In this paper, Eriobotrya japonica Lindl. cv. Zaozhong No. 6 seedlings were used to study the effects of exogenous 5-aminolevulinic acid (ALA) application on glutathione synthesis and cyclic metabolism of loquat seedlings under low-temperature stress and to explore the regulatory mechanism of ALA on loquat cold tolerance. The results showed that ALA treatment could increase the content of GSH and the reduced glutathione/oxidized glutathione (GSH/GSSG) ratio in loquat leaf slices under low-temperature stress; reduce the electrolyte leakage rate and GSSG, H₂O₂ and MDA contents in leaf tissues; and alleviate the peroxidation damage caused by low temperature. ALA treatment increased the activity of γ-glutamine synthetase (γ-ECS) in loquat leaf slices under low-temperature stress and promoted the biosynthesis of reduced glutathione, thereby increasing the GSH content in leaf tissues. On the other hand, ALA treatment could also improve the activities of glutathione reductase (GR), glutathione S-transferase (GST) and glutathione peroxidase (GPX) and promote the cyclic regeneration of GSH, accordingly maintaining a high GSH/GSSG ratio, promoting the removal of reactive oxygen species (ROS), and enhancing the antioxidant capacity of leaves. The regulatory effect of ALA on enhancing the antioxidant capacity of loquat seedlings under low-temperature stress can be inhibited by L-buthionine-sulfoximine (BSO, GSH biosynthesis inhibitor). The results showed that ALA improved the antioxidant capacity of loquat seedlings under low-temperature stress, and GSH was involved in the regulation of the antioxidant effect of ALA on loquat seedlings under low-temperature stress.

Urban floods are typical urban disasters that threaten the economy and development of cities. Sponge cities can improve the flood resistance ability and reduce the floods by setting low-impact development measures (LID). Evaluating the floods reduction benefits is the basic link in the construction of sponge cities. Therefore, it is of great significance to evaluate the benefits of sponge cities from the perspective of different rain patterns. In this study, we investigated the urban runoff of various rainfall patterns in Mianyang city using the Strom Water Management Model (SWMM). We employed 2–100-year return periods and three different temporal rainfall downscaling methods to evaluate rain patterns and simulate urban runoff in Mianyang, with and without the implementation of sponge city measures. After calibration, model performance was validated using multi-source data concerning flood peaks and inter-annual variations in flood magnitude. Notably, the effects of peak rainfall patterns on historical floods were generally greater than the effects of synthetic rainfalls generated by temporal downscaling. Compared to the rainfall patterns of historical flood events, the flood protection capacities of sponge cities tended to be overestimated when using the synthetic rainfall patterns generated by temporal downscaling. Overall, an earlier flood peak was associated with better flood sponge city protection capacity.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

Low-energy Coulomb excitation is capable of providing unique information on static electromagnetic moments of short-lived excited nuclear states, including non-yrast states. The process selectively populates low-lying collective states and is therefore ideally suited to study phenomena such as shape coexistence and development of exotic deformation (triaxial or octupole shapes). Historically, these experiments were restricted to stable isotopes. However, the advent of new facilities providing intense beams of short-lived radioactive species has opened the possibility to apply this powerful technique to a much wider range of nuclei. We discuss the observables that can be measured in a Coulomb-excitation experiment, their relation to nuclear structure parameters with an emphasis on the nuclear shape, and present some recent examples of Coulomb-excitation studies that provided outcomes relevant for the Shell Model.

Pain is an unpleasant emotional and sensory experience. For many years orthodontists have been looking for an effective method of reducing this feeling of discomfort. In recent years, low-level laser therapy (LLLT) has taken hold in the orthodontic field. Among the countless advantages it can modulate the painful feeling. The aim of this research is to identify the use of photobiomodulation in subjects undergoing fixed orthodontic treatment, to reduce the pain and discomfort that it causes. The research was conducted from the Web of Science, Pubmed and Scopus databases. Only 14 of all articles met the inclusion and exclusion criteria and were therefore used to conduct the research. The different studies compared, in most cases, patients whose mouth was divided into a part treated with laser therapy and a placebo part. The results show a statistically significant difference in perceived pain between the irradiated arch and the non-irradiated arch. Three authors didn’t find statistically significant results in favour of low-laser therapy, but it is important to remember that they used different parameters. To obtain generally valid studies, with consistent and reproducible results, it is necessary to standardize the different parameters used that are independent by operator performing the procedure.