As society becomes more reliant on Lithium-ion (Li-ion) batteries, state-of-health (SOH) estimation will need to become more accurate and reliable. Therefore, SOH modelling is in the process of shifting from using simple and continuous charge/discharge profiles, to more dynamic profiles constructed to mimic real operation, when ageing the Li-ion batteries. However, in most cases, when ageing the batteries, the same exact profile is just repeated until the battery reaches its end-of-life. Using data from batteries aged in this fashion to build a model, there is a very real possibility that the model will rely on the built-in repetitiveness of the profile. Therefore, this work will examine the dependence of the performance of a multiple linear regression on the number of charges used to train the model, and their location within the profile used to age the batteries. The investigation shows that it is possible to build models using randomly selected partial charges while still reaching errors as low as 0.5%. Furthermore, it shows that only two randomly sampled partial charges are needed to achieve errors of less than 1%. Lastly, as the number of randomly sampled partial charges used to create the model increases, then the dependence on particular partial charges tends to decrease.

The potential of metallic lithium to become the anode material for next-generation batteries is hampered by significant challenges, chief among which is dendrite growth during battery charging. These dendritic structures not only impair battery performance but also pose safety risks. Among the non-destructive analytical techniques in battery research, Magnetic Resonance Imaging (MRI) stands out as a promising tool. However, the direct imaging of lithium by 7Li MRI is hindered by its low sensitivity and spatial resolution, making its use for of dendritic growth imaging very difficult. Instead, a recently introduced indirect imaging approach based on 1H MRI of the electrolyte was used in this study. This method was used for sequential 3D imaging to monitor the charging process of lithium metal symmetric cells in three different electrical circuits: single cell, four cells in parallel, four cells in series. The measured sequential images allowed measurement of dendrite growth in each cell using volumetric analysis. The growth results confirmed the theoretical expectation that growth across cells is uneven in a parallel circuit and even in a series circuit. The methods presented in this study can be applied also to many other dendrite-related issues in batteries.

World Health Organization recommends adjusting the salt intake as a part of the nine global targets to reduce premature mortality from non-communicable chronic diseases as priority and most cost-effective intervention. In 2006. the main aim of the Croatian Action on Salt and Health was to decrease salt intake for 16% because of its critical intake and consequences on human health. We have organized educative activities for increasing awareness on salt harmfulness, defined food categories of prime interest, collaborate with industries and determine salt intake (24h urine-sodium excretion). It was determined that the proportion of salt in ready-to-eat baked bread should not exceed 1.4%. In the period 2014 –2022, salt in the semi-white bread was reduced 14%, in bakery 22% and in largest meat industry in Croatia 25%. Awareness of the harmfulness of salt on health increased from 65.3% in 2008 to 96.9% in 2023 and salt intake was reduced 15.9%-1.8 grams/day (22.8% men, 11.7% women). In last 18 years a significant decrease in salt intake was achieved in Croatia, awareness of its harmfulness increased, collaboration with food industry established and regulatory documents launched. However, salt intake is still very high underlying the need for continuation of efforts and even stronger activities.

In this study, multilayer composite nanofiber membranes of sodium alginate (SA) /polyethyleneimine (PEI)/polyvinyl alcohol (PVA) was fabricated via electrospinning technique to enhance the adsorption of Cu2+ from wastewater. The preparation and adsorption mechanisms of the SA/PEI/PVA nanofiber membranes were analyzed by utilizing analytical techniques such as SEM, FTIR, EDS, UV-vis, XRD, and TG. The obtained nanofiber membrane characterized by small diameter, high uniformity, and extensive surface area, demonstrate significant potential for heavy metal ion filtration. Optimal spinning parameters were identified, including a voltage of 19.5 KV, a distance of 8 cm, and specific mass ratios (SA: PEI: PVA, 1:2:6) and injection speeds (8 μL/min) and. The resulting nanofibers with an average diameter of 112.5 nm exhibited excellent morphology and high efficiency, retaining over 85% adsorption capacity for Cu2+ in initial tests and maintaining above 80% efficacy through four successive filtration cycles.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

The article studies and analyzes a hybrid power source system, lithium battery, and fuel cell assisted by flexible photovoltaic panels for hybrid electric vehicles (HEVs). The new configuration operates based on optimizing the performance of the dual power source to maximize the available energy and operating time. The operational mode simulates specific driving conditions in urban, peripheral, and intercity routes under variable driving patterns and traffic conditions. The simulation results show that the new configuration increases the hybrid electric vehicle performance, providing higher reliability despite the more complex design. The proposed system reduces the external power supply dependence and avoids unexpected sudden stops due to energy exhaustion. The new configuration also extends the vehicle driving range depending on driving mode and route conditions. The vehicle driving range extension may reach up to 276.3 km. The hybridization of fuel cells with lithium battery and PV panel assistance enhances battery management, reducing battery servicing and increasing lifespan. The proposed topology is cheaper than a single fuel cell power system by 17.2%, reducing the total cost related to the single battery power system if we consider the battery recharge for its entire lifespan. The cost saving is 2.6% for the American market and 14.8% for the European one.

The current state-of-the-art does not provide a universal and rapid method of determining the state of health (SOH) of a battery or a supercapacitor without carefully examining the degradation of hundreds of full charge/discharge cycles. Lithium-ion batteries, sodium-ion batteries and supercapacitors of different cell chemistries were studied by impedance spectroscopy during lifetime tests. Faradaic and capacitive charge storage are distinguished by the relationships between stored electric charge and capacitance. For batteries, impedance spectroscopy is best applicable in the flat region of the voltage-charge curve. An approximately linear correlation between pseudocapacitance and Ah capacity is observed as long as overcharge and deep discharge are avoided. The correct calculation of quantities related to complex impedance and differential capacitance is outlined – which may also be useful as an introductory text and tutorial for newcomers to the field. Novel diagram types are proposed for the purpose of instant performance and failure diagnosis of batteries and supercapacitors.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

Recent experiments devoted to characterizing the behavior of sessile ferroelectric liquid droplets on ferroelectric solid substrates, showed the existence of a droplet electromechanical Rayleigh-like instability. The instability is induced by the bulk polarization of the ferroelectric fluid which couples to the polarization of the underlying substrate through its fringing field and solid-fluid interface coupling. With the aim of characterizing this phenomenon, namely the coupling between the polarizations of a fluid and a solid material, we studied the behavior of ferroelectric liquid droplets confined between two solid substrates, arranged in different configurations realized so to generate fringing fields with different profiles. Results show that the features of the droplets instability are indeed affected by the specific fringing field shape in a way dominated by the minimization of the electrostatic energy associated to the bulk polarization of the ferroelectric fluid.

India has pledged ambitious initiatives to mitigate its growing economies’ impact on the climate, including a goal of net zero emissions by 2070. The transportation sector is one of the key sources of emissions. Therefore, fostering e-mobility within this sector is a key priority for the Indian government. The lifecycle of LiBs raises numerous concerns regarding its sustainability in production, use of rare materials, and most importantly waste management. Furthermore, this paper will highlight the case for EV battery recycling as a growing sector that also has the potential to foster circularity in the EV sector. Through the introductory section, this paper lays out rationale for battery recycling in a circular EV economy. The subsequent sections discuss the current and emerging battery technologies and their link to recycling methods whilst overviewing domestic and foreign battery recycling companies. Finally, the paper concludes with a gap assessment of the battery recycling ecosystem in India and makes recommendations to further integrate this industry into the EV supply chain. As India steers towards a sustainable future, it is imperative that the country integrates battery recycling to enhance circularity in the EV ecosystem, closing the gap between a growing number of EVs and waste management.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

The excessive intake of sodium (Na) and insufficient intake of potassium (K) are major concerns to prevent hypertension. Using low-Na/K seasonings (reducing 25% of the NaCl and adding K salt) may improve the dietary Na/K ratio and help prevent hypertension. To devise an intervention study using low-Na/K seasonings at a company cafeteria, we calculated the Na and K contents of the meals served at the cafeteria and estimated changes in the intakes when suitable low-Na/K seasonings were used. We also considered using milk as a good source of K. We used an ingredient list of a company cafeteria and calculated Na and K contents in each dish. The average amounts of NaCl and K per use were 5.04 g and 718 mg, respectively. Seasonings contributed 70.9% of the NaCl. With the use of low-Na/K seasonings, an estimated reduction in NaCl of 0.8 g/day and an estimated increase in K of 308 mg/day was achieved. An additional serving (200 mL) of milk, NaCl was reduced by 0.57 g/day and K was increased by 610 mg/day, with an overall decrease in the dietary Na/K ratio from 3.20 to 2.40. The use of low-Na/K seasonings and dairy may improve the dietary Na/K ratio among cafeteria users and help prevent hypertension.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

As the global transition towards renewable energy accelerates, the integration of grid-scale energy storage systems has become increasingly critical for stabilizing energy supply and enhancing grid reliability. Among various storage technologies, lithium-ion batteries stand out for their high energy density, scalability, and relatively low environmental impact. This study investigates the performance and longevity of lithium-ion batteries in grid-scale applications, focusing on the impact of operational parameters such as cycling frequency, depth of discharge, temperature fluctuations, and charging/discharging rates. Employing a mixed-methods approach, we combined quantitative analysis of performance metrics (cycle life, capacity fade, efficiency) with qualitative assessments from case studies of existing grid-scale projects. Our findings reveal that while lithium-ion batteries exhibit robust performance in grid-scale storage, their longevity and efficiency are significantly influenced by operational conditions. Specifically, temperature management and optimized cycling strategies were identified as key factors in mitigating degradation and extending battery life. This research provides a comprehensive understanding of lithium-ion battery behavior in grid-scale environments, offering valuable insights for the design, optimization, and management of energy storage systems. By addressing the challenges of battery performance and longevity, our study contributes to the development of more sustainable and reliable grid storage solutions, facilitating the broader adoption of renewable energy sources.

The accurate state of health (SOH) estimation of lithium-ion batteries (LIBs) during operation is crucial to ensure optimal performance, prolonging battery life and preventing unexpected failure or safety hazards. This work presents a storage and performance optimised deep learning approach to predict the capacity based SOH of LIBs using raw sensor data from partial charging curves under constant current condition. The proposed model is based on a combination of a 1-dimensional convolutional and long-short term memory neural network and processes time, voltage and incremental capacity of partial charging curves as time series. The model is cross-validated on different aging scenarios reaching an overall MAE = 0.418% and RMSE = 0.531%, promising an accurate SOH estimation of LIBs under varying usage and environmental conditions in a real world application.

Zirconia-reinforced lithium silicate (ZLS) is utilized as a material for prosthetic tooth crowns, offering enhanced strength compared to other dental glass-ceramics. In this study, we investigate a commercial ZLS material, provided in a fully crystallized form. We examine the effects of an optional post-processing heat treatment on micro-contact damage using controlled indentation tests simulating the primary modes of contact during chewing: axial and sliding. Our findings indicate that the heat treatment does not affect mechanical properties such as the elastic modulus, hardness and indentation fracture toughness. However, it does enhance the resistance to contact damage by fracture and chipping in both axial and sliding modes, as well as the resistance to crack initiation measured from sliding tests. This improvement is attributed to the refinement of the flaw population achieved through the heat treatment. The results are analysed within the framework of contact and fracture mechanics, and the implications for prosthetic dentistry are briefly discussed.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

This study evaluates the efficacy of the salts, sodium metabisulfite (SMB), ammonium bicarbonate, sodium bicarbonate and potassium dihydrogen orthophosphate first in vitro against the main postharvest fruit rot fungi, Alternaria alternata, Botrytis cinerea, Penicillium italicum and Penicillium digitatum. Results showed that 0.2% SMB completely inhibited mycelium growth of the fungal species. Ammonium bicarbonate and sodium bicarbonate were less effective at 0.2% in inhibiting mycelial growth, ranging from 57.6% to 77.6%. The least effective was potassium dihydrogen or-thophosphate. Experiments were also performed in vivo on wounded apples inoculated with the most pathogenic fungus, B. cinerea, and treated with SMB at concentrations of 0.2, 0.5, 1, 2 and 3%, both preventively and curatively. Results based on the decay size showed that SMB, when used as a preventive treatment, had a reduced efficacy, even with the highest concentration. However, this salt proved to be very effective at 0.5% in curative treatment, since the decay was completely blocked. Our results suggest that the appropriate concentration of SMB for post-harvest treatment is 0.5% as a curative treatment. On the other hand, the 1% dose induced the onset of phytotoxicity around the wound. To assess the extent of phytotoxicity reaction, higher concentrations of 1-4% SMB were applied to wounded fruit. Apples and oranges were inoculated or not with B. cinerea and P. digitatum respectively. Doses of 1- 4% induced phytotoxicity in the form of a discoloured ring surrounding the wound on the epidermis of the fruit; this phytotoxicity enlarged as the concentration of SMB increased. The phytotoxic features were similar on apples and oranges. The methodological procedure made it possible to carry out a quantitative assess-ment of SMB phytotoxicity. This method is proposed as an easy-to-use technique for quantitatively estimating the phytotoxicity of antifungal compounds on post-harvest fruit.

Azobenzene photoswitches are fundamental components in contemporary approaches aimed at light-driven control of intelligent materials. Significant endeavors are directed towards enhancing the light-triggered reactivity of azobenzenes for such applications and obtaining water-soluble molecules able to act as crosslinkers in a hydrogel. Here, we report the rational design and the synthesis of azobenzene/alginate photoresponsive hydrogels endowed with fast reversible sol-gel transition. We started with the synthesis of three cationic azobenzenes (AZO A, B, and C) and then incorporated them in sodium alginate (SA) to obtain photoresponsive supramolecular hydrogels (SMHGs). The photoresponsive properties of the azobenzenes were investigated by UV-Vis and ¹H NMR spectroscopy. Upon irradiation with 365 nm UV light, the azobenzenes demonstrated efficient trans-to-cis isomerization, with complete isomerization occurring within seconds. The return to the trans form took several hours, with AZO C exhibiting the fastest return, possibly due to higher trans isomer stability. In the photoresponsive SMHGs, the minimum gelation concentration (MGC) of azobenzenes was determined for different compositions, indicating that small amounts of azobenzenes could induce gel formation, particularly in 5 wt% SA. Upon exposure to 365 nm UV light, the SMHGs exhibited reversible gel-sol transitions, underscoring their photoresponsive nature. This research offers valuable insights into the synthesis and photoresponsive properties of cationic, water-soluble azobenzenes, as well as their potential application in the development of photoresponsive hydrogels.

The beneficial effects of Lanthanide incorporation into 0.94Na0.5Bi0.5TiO3-0.06BaTiO3 (BNT-BT) matrix on its functional properties were investigated. The conventional solid-state method was used for synthesizing samples. The structural refinement revealed that all samples crystallized in R3c rhombohedral symmetry. Raman spectroscopy study was carried out using green laser excitation and revealed that no clear perceptible variation in frequency is observed. Dielectric measurements unveiled that the introduction of rare earth obstructed the depolarization temperature promoted in BNT-BT with decreasing the diffusive phase transition with increasing the lanthanide size. Only Dysprosium addition showed comparable diffusion constant and dielectric behavior as the unmodified composition. Further, the comparison of the obtained ferroelectric hysteresis and strain-electric field loops revealed that only Dy-phase exhibited interesting properties comparing parent composition. In addition, the incorporation of lanthanides Ln3+ into the BNT-BT matrix led to the development of luminescence characteristics in the visible and near infrared regions, depending on the excitation wavelengths. The simultaneous occurrence of photoluminescence and ferroelectric/piezoelectric properties opens up possibilities for BNT-BT-Ln to exhibit multifunctionality in a wide range of applications.Keywords: Sodium Bismuth Titanate; structural refinement; dielectric properties; ferroelectric properties; piezoelectric properties; Photoluminescence.

During the last decade, the demand for lithium has been growing exponentially with its widespread uses in manufacturing, especially with the worldwide deployment of electric vehicles. Thus, lithium is considered integral to the U.S. economy, technological advancement, and the pursuit of sustainable and clean energy solutions. The produced water is known to be rich in several minerals and valuable elements, such as potassium and magnesium, and a trace amount of precious elements including lithium. However, the existence of metals in the produced water is one of the challenges to extract lithium, especially magnesium which is located in diagonal positions within the periodic table that exhibit similarities. The produced water was first purified, resulting in the complete removal of magnesium, and then lithium was precipitated by phosphate. The effects of operating conditions on the Li₃PO₄ precipitation behaviors were evaluated. The effect of different precipitating reagents was evaluated on the percentage of lithium extracted, Na₃PO4 (TSP) was found to be a promising Li precipitating reagent. The highest percentage of lithium extracted was reached when the Li concentration of produced water was enriched and increased up to 350 mg/l, then Li removal was 53% at 7 grams of TSP and 200 rpm for 2 hours. The results indicated that temperature is a more important factor than stirring speed. The novelty of the current work is not only by the results obtained that may create additional financial benefits to oil-producing areas but on that the sustainable disposal of produced water may encourage the recycling and reuse practice, ultimately reducing the use of freshwater for hydraulic fracturing.

This is an exercise to explore the concentration of Lithium, Lithium-7 isotope and the possible presence of black dirty ice in the lunar surface using spectral data obtained from the Clementine mission. The main interest in tracing the lithium and presence of dark ice in the lunar surface are closely related to future human settlement missions in the Moon. We investigate the distribution of Lithium and 7 Li isotope on the Lunar surface, employing spectral data from the Clementine images. We utilized Visible (VIS-NIR) imagery at wavelengths of 450, 750, 900, 950, and 1000 nm, along with Near-Infrared (NIR-SWIR) at 1100, 1250, 1500, 2000, 2600, and 2780 nm, encompassing 11 bands in total. This dataset offers a comprehensive coverage of about 80% of the lunar surface, with resolutions ranging from 100 to 500 meters, spanning latitudes from 80°S to 80°N. In order to extract quantitative abundance of Lithium, ground truth sites were used to calibrate the Clementine images. Samples (12045, 15058, 15475, 15555, 62255, 70035, 74220 and 75075) returned from Apollo missions 12, 15, 16 and 17 have been correlated to the Clementine VIS-NIR bands and five spectral ratios. The 5 spectral ratios calculated synthesize the main spectral features of sample spectra that were grouped by their Lithium and 7 Li content using Principal Component Analysis. The ratios spectrally characterize substrates of anorthosite, silica-rich basalts, olivine-rich basalts and High-T mare basalts and Orange soils. Our findings reveal a strong linear correlation between the spectral parameters and the lithium content in the 8 Apollo samples. With the values of the 11 Clementine bands and the 5 spectral ratios for each of the 8 lunar soils we performed linear regression models to estimate the concentration of Lithium and 7 Li. Also, we calculated Digital Terrain Models (DTMs; Altitude, Slope, Aspect, DirectInsolation and WindExposition) from LOLA-DTM to discover relations between relief and spatial distribution of the extended models of lithium and 7 Li. The analysis was conducted in a mask polygon extracted from Lunar Orbiter Laser Altimeter (LOLA) and located around the Apollo 15 landing site. This analysis seeks to uncover potential 7 Li enrichment through spallation processes, influenced by varying exposure to solar wind. To explore the possibility of find ice mixed with regolithe (black ice) we used a spectral library (350-2500nm) form ices dirty with different concentration of volcanic particles.

Chronic diseases, such as type 2 diabetes (T2D), are difficult to manage because they demand continuous therapeutic review and monitoring. Beyond achieving the target HbA1c, new guidelines for the therapy of T2D have been introduced with the new groups of antidiabetics (GLP-1ra and SGLT2-in). Despite new guidelines, clinical inertia, that can be caused by physicians, patients or healthcare system, results in T2D not being effectively managed. This opinion paper explores the shift in T2D treatment, challenging assumptions and evidence-based recommendations, particularly for family physicians, considering the patient's overall situation in decision-making. We looked for the possible reasons of clinical inertia and poor application of guidelines in the management of T2D. Guidelines for antidiabetic drugs should be more precise, providing case studies and clinical examples to define clinical contexts and contraindications. Knowledge communication can improve confidence and should include clear statements on areas of decision-making not supported by evidence. Precision medicine initiative in diabetes aims to identify subcategories of T2D patients (including frail patients) using clustering techniques from data science applications, focusing on CV and poor treatment outcomes. Clear, unconditional recommendations for personalized T2D management may encourage drug prescription, especially for family physicians dealing with diverse patient contexts and clinical settings.

Hydrogen plays an important role in the implementation of Australia’s Net-Zero Strategy. It competes with lithium-ion rechargeable batteries in the electrification of Australian land transportation sector, and can provide an alternative energy storage medium for the greening of the country’s electrical grid system. This paper reviews the role hydrogen plays in the current government’s Net-Zero strategy, and investigates the potential role of other bioenergy sources. It is found that hydrogen and batteries play essentially complementary roles in reducing transport emissions, and that the former energy source is more suited to the operation of long-distance commercial service vehicles than batteries. It is suggested that bioenergy fuels such as biomethane, second generation biofuels and HVO can provide suitable bridging alternatives in the event that Australia’s EV strategy is unable to meet the 2030 target.

Heart failure (HF) management in type 1 diabetes (T1D) is particularly challenging due to its increased prevalence and the associated risks of hospitalization and mortality, driven by diabetic cardiomyopathy. Sodium-glucose cotransporter-2 inhibitors (SGLT2-i) offer a promising avenue for treating HF, specifically the preserved ejection fraction variant most common in T1D, but their utility is hampered by the risk of euglycemic diabetic ketoacidosis (DKA). This review investigates the potential of SGLT2-i in T1D HF management, alongside the emergent Continuous Ketone Monitoring (CKM) technology as a means to mitigate DKA risk, through a comprehensive analysis of clinical trials, observational studies, and reviews. The evidence suggests SGLT2-i significantly reduce HF hospitalization and enhance cardiovascular outcomes. However, their application in T1D patients remains limited due to DKA concerns. CKM technology emerges as a crucial tool in this context, offering real-time monitoring of ketone levels, which enables the safe incorporation of SGLT2-i into treatment regimes by allowing for early detection and intervention in the development of ketosis. The synergy between SGLT2-i and CKM has the potential to revolutionize HF treatment in T1D, promising improved patient safety, quality of life, and reduced HF-related morbidity and mortality. Future research should aim at clinical trials directly assessing this integrated approach, potentially guiding new management protocols for HF in T1D.

Significant efforts are being made across academia and industry to better characterize lithium-ion battery cells as reliance on the technology for applications ranging from green energy storage to electric mobility increases. The measurement of short-term and long-term volume expansion in lithium-ion battery cells is relevant for several reasons. For instance, it provides information about the quality and homogeneity of battery cells during charge and discharge cycles, as well as aging over it’s lifetime. The expansion measurements are useful for the evaluation of new materials and the improvement of end-of-line quality tests during cell production. These measurements may also indicate the safety of battery cells by aiding in predicting state of charge and state of health over the lifetime of the cell. Expansion measurements can also assess inhomogeneities on the electrodes and defects such as gas accumulation and lithium plating. In this review, we first establish the known mechanisms through which short term and long term volume expansion in lithium-ion battery cells occurs. We then explore the current state-of-the-art for both contact and non-contact measurements of volume expansion. This review compiles existing literature to outline the various options available to researchers aiming to make ex situ volume expansion measurements by doing post mortem analyses on individual components and in operando measurements on entire battery cells. Finally, we discuss the different considerations when selecting an appropriate measurement technique. The selection of the optimal method for measuring battery cell expansion depends on the objective of the characterization, duration, required resolution, and repeatability of results. Costs and required space for the measurement equipment are also considered.

A The aim of this study is to analyze the effect of different endodontic irrigants and adhesive systems on resin bond strength of fiber post cementation. 144 single-rooted, unrestored human teeth were endodontically treated and randomly divided into 12 groups according to 4 endodontic irrigants (distilled water as control; EDTA 17%; NaOCl 5%; clorhexidine 2%) and 3 different adhesive/resin cement systems (etch-and-rinse: ortofosforic acid, Parabond® A+B/Paracore®; self-etch: ParaBond® Non-Rinse Conditioner, Parabond® A+B /Paracore®; Universal: ClearfilTM Universal Bond/ ClearfilTM DC Core Plus). 48 h after post cementation ten teeth from each group were cross sectioned into 3 discs (cervical, middle and apical regions). 30 specimens of each group (n=30) were submitted to push-out test at a crosshead speed of 1 mm/min. The remaining 2 teeth of each group were sectioned in the same manner and the resin-dentin interface was evaluated using scanning electron microscopy (SEM). The results were statistically analyzed with the ANOVA and Tukey’s test (< 0,01). The adhesive protocols and post space region showed no significant effect on bond strength (> 0.01). The combination of NaOCl 5% and ClearfilTM Universal Bond reduced the adhesive strength (< 0.01). The NaOCl 5%, in relation with other irrigants, significantly decreased the push-out bond strength.

In this study, the effect of NaOCl (10–200 ppm of Cl2) on the inactivation of human norovirus (HuNV) GII.4 and hepatitis A virus (HAV) in groundwater was investigated using PMA/RT­qPCR. Initially, 4.00 log copies/μL of HuNV GII.4 or 5.50 log copies/μL of HAV were artificially inoculated in ground water. The titers of HuNV GII.4 and HAV decreased significantly (p < 0.05) with increasing Cl2 concentrations. Ground water was treated with 10, 30, 50, 100, 150, and 200 ppm of Cl2, and the viable HuNV GII.4 was significantly (p < 0.05) reduced to 3.28 (0.21 log reduction), 3.18 (0.31 log reduction), 3.01 (0.48 log reduction), 2.75 (0.74 log reduction), 2.54 (0.95 log reduction), and 2.34 (1.15 log reduction) log copies/μL, respectively. The viable HAV was also significantly (p < 0.05) reduced to 4.99 (0.23 log reduction), 4.76 (0.46 log reduction), 4.55 (0.67 log reduction), 4.21 (1.01 log reduction), 3.89 (1.33 log reduction), and 3.64 (1.58 log reduction) log copies/μL, respectively. The decimal reduction time (D-value) (1-log reduction) of HuNV GII.4 and HAV infectivity in ground water was predicted as 116.7 and 98.9 ppm of Cl2, respectively using the first-order kinetics model (HuNV GII.4 ; y = - 0.0054x + 3.3585, R2= 0.97, HAV ; y = - 0.0091x + 5.0470, R2= 0.97). The result specifically suggests that 150–200 ppm Cl2 can potentially be used for the inactivation of > 1 log copies/μL HuNV GII.4 and HAV in ground water.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

This research aims to deepen the understanding of the relationship between conductivity and morphology in polypyrrole (PPy) via a comparison of the bipolaron to polaron ratios with a focus on the C-H deformation area. PPy samples were synthesized with different surfactants: sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB), and tween 80 (TW). The study revealed that SDS significantly altered the bipolaron and polaron in C-H deformation region and showed higher conductivity than other surfactants. Notably, the morphological shifts to a sheet-like structure when using ammonium sulfate (APS) contrasted with the particle-like form observed with ferric chloride (FeCl3). These results showed that if the oxidant changed, the bi-polaron and polaron ratios in C-H deformation were unrelated to PPy morphology. However, this work showed a consistent relationship between SDS use, the bipolaron and polaron ratios in the C-H deformation, and the conductivity properties. Moreover, the natural positive charge of PPy and negatively charged SDS molecules may lead to an electrostatic interaction between PPy and SDS. This work assumes that this interaction might cause the transformation of polaron to bipolaron in the C-H deformation region, resulting in improved conductivity of PPy. This work offers more support for the future investigation of PPy characteristics.

The high demand for lithium (Li) relates to clean renewable storage devices and the advent of electric vehicles (EVs). The extraction of Li ions from aqueous media calls for efficient adsorbent materials with various characteristics, such as good adsorption capacity, good selectivity, easy isolation of the Li-loaded adsorbent, and good recovery of the adsorbed Li ions. The widespread use of metal-based adsorbent materials for Li ions extraction relates to various factors: (i) the ease of preparation via inexpensive and facile templation techniques, (ii) excellent selectivity for Li ions in a matrix, (iii) high recovery of the adsorbed ions, and (iv) good cycling performance of the adsorbents. However, the use of nano-sized metal-based LISs is limited due to challenges associated with isolating the loaded adsorbent material from the aqueous media. Adsorbent granulation process employing various binding agents (e.g., biopolymers, synthetic polymers, and inorganic materials) affords functional particles with modified morphological and surface properties that support easy isolation from the aqueous phase upon adsorption of Li ions. Biomaterials (e.g., chitosan, cellulose, alginate, and agar) are of particular interest because their structural diversity renders them amenable to coordination interactions with metal-based LISs to form 3D microcapsules. The current review highlights recent progress in the use of biopolymer binding agents for the granulation of metal-based LISs, along with various crosslinking strategies employed to improve the mechanical stability of the granules. The study reviews the effects of granulation and crosslinking on adsorption capacity, selectivity, isolation, recovery, cycling performance and the stability of the LISs. Adsorbent granulation using biopolymer binders has been reported to modify the uptake properties of the bio-adsorbent materials to varying degrees, in accordance with the surface and textural properties of the binding agent. The review further highlights the importance of granulation and crosslinking for improving the extraction process of Li ions from aqueous media. This review contributes to manifold areas related to industrial application of LISs, as follows: 1) to highlight recent progress in the granulation and crosslinking of metal-based adsorbents for Li ions recovery, 2) to highlight the advantages, challenges, and knowledge gaps of using biopolymer-based binders for granulation of LISs, and finally, 3) to catalyze further research interest into the use of biopolymer binders and various crosslinking strategies to engineer functional adsorbent materials for application in Li extraction industry. Properly engineered extractants for Li ions are expected to offer various cost benefits in terms of capital expenditure, percent Li recovery, and reduced environmental footprint.

Tungsten is a high-value resource with a wide range of applications. The end-products of tungsten industry are tungsten metal and alloys that are produced through many steps from high-grade concentrates. Pyrometallurgical extraction of tungsten from complex and low-grade ores has great potential to overcome the problems associated with the hydrometallurgical process. In this study, sodium carbonate and silica were used to extract tungsten from wolframite at high temperatures. Sodium tungstate can be obtained directly from the smelting reaction between 1100 and 1300 oC. The smelting slag is further water-leached to recover sodium tungstate in the solution. The effects of Na2CO3/Ore and SiO2/Ore ratios, temperature and reaction time on the recovery of tungstate and the purity of sodium tungstate were systematically studied, which provides a theoretical basis for the pyrometallurgical smelting process of tungsten extraction.

The ubiquitous deployment of Li-ion batteries (LIBs) in more demanding applications has reinforced the need to understand root-causes of thermal runaway. Herein we perform a forensic simulation of a real-case failure scenario, using localised heating of Li(Ni0.5Mn0.3Co0.2)O2 versus graphite 18650 cylindrical cells. This study determined the localised temperatures that would lead to venting and thermal runaway of these cells, as well as correlating the gases produced as a function of degradation pathway. Catastrophic failure, involving melting (with internal cell temperatures exceeding 1085°C), deformation and ejection of cell componentry, was induced by locally applying 200 °C and 250 °C to a fully charged cell. Conversely, catastrophic failure was not observed when the same temperatures were applied to the cells at lower state of charge (SOC). This work highlights the importance of SOC, chemistry and heat in driving the thermal failure mode of Ni-rich LIB cells, allowing for a better understanding of battery safety and associated design improvements.

The separation of Li+ and [Bmim]+(1-Butyl-3-methylimidazolium) by electrically driven membrane technology was studied. The effects of the types and modification processes of cation exchange membranes, current density, total cation concentration, temperature, and anion types on separation efficiency were investigated. The results indicated that it is feasible to achieve efficient separation of Li+ and [Bmim]+ using the selectivity of cation exchange membranes under electric field. Membrane CMX and the modified membrane A and B which obtained from the CMX showed obvious selective of Li+ from [Bmim]+. When the current density is 5 mA/cm2 and the feed concentrations of Li+ and [Bmim]+ are 0.3 mol/L and 0.2 mol/L, the selective transport coefficient of the modified membrane B can reach 6.2 in the first 120 minutes of the process. Reducing current density and increasing total cation concentration can improve separation efficiency. Lowering the temperature can improve the separation effect, but improvement is not obviously. Changing the anion of the feed from chloride ion to acetate has no effect on the separation.

End-of-life electric vehicle (EV) batteries can be reused to reduce their environmental impact and economic costs. However, the growth of a second-life market is limited by the lack of information on the characteristics and performance of these batteries. As the volume of end-of-life EVs may exceed the amount of batteries needed for stationary applications, investigating the possibility of repurposing them in mobile applications is also necessary. This article presents an experimental test that can be used to collect the data necessary to fill a battery passport. The proposed procedure can facilitate the decision making process regarding the suitability of a battery for reuse at the end of its first life. Once the battery passport has been completed, the performance and characteristics of the battery are compared with the requirements of several mobile applications. Mobile charging stations and forklift trucks were identified as relevant applications for the reuse of high capacity prismatic cells. Finally, a definition of a state of health (SoH) is proposed to track the suitability of the battery during use in the second life application considering not only energy but also power and efficiency of the battery. This SoH shows that even taking into account accelerated ageing data, a repurposed battery can have an extended life of 11 years at 25~°C. It has also been shown that energy fade is the most limiting performance for lifetime and that cell-to-cell variation should be tracked as it has been shown to have a significant impact on battery life.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

With the proliferation of electric vehicles (EVs) and the consequential increase in EV battery circulation, the need for accurate assessment of battery health and remaining useful life (RUL) is paramount, driven by environmentally friendly and sustainability goals. This study addresses this pressing concern by employing data-driven methods, specifically harnessing deep learning techniques to enhance RUL estimation for lithium-ion batteries (LIB). Leveraging the Toyota Research Institute Dataset, consisting of 124 lithium-ion batteries cycled to failure and encompassing key metrics such as capacity, temperature, resistance, and discharge time, our analysis substantially improves RUL prediction accuracy. Notably, the Convolutional-LSTM-Deep Neural Network (CLDNN) model and the Transformer-LSTM (Temporal-Transformer) model have emerged as standout Remaining Useful Life (RUL) predictors. The CLDNN model, in particular, achieved a remarkable Mean Absolute Error (MAE) of 84.012 and a Mean Absolute Percentage Error (MAPE) of 25.676. Similarly, the Temporal-Transformer model exhibited notable performance with an MAE of 85.134 and a MAPE of 28.7932. These impressive results were achieved through the application of Bayesian hyperparameter optimization, further enhancing the accuracy of predictive methods. These models were benchmarked against existing approaches, demonstrating superior results with an improvement in MAPE ranging from 4.01% to 7.12%.

This study is dedicated to enhancing lithium battery performance through the utilization of porous conductive polyaniline-modified graphene composites (PMGC). Given the growing importance of green energy, coupled with the development of lithium-ion battery systems and electric vehicles, achieving high-speed charge and discharge performance has become imperative. Traditional approaches involve incorporating additives like carbon nanotubes and graphene into electrodes to improve conductivity, but they encounter challenges related to cost and aggregation issues. In this study, polyaniline (PANI), a cost-effective, stable, and conductive polymer, was explored. PMGC was formed by employing ammonium persulfate (APS) as an oxidant during PANI polymerization, simultaneously serving as a surface modifier for graphene. The study systematically investigated the impact of varying amounts of PMGC on lithium-ion battery electrodes, assessing reductions in internal resistance, aging effects, different charge and discharge rates, and cycle performance. PMGC exhibited a porous structure formed by nanoscale PANI intertwining on graphene. Various measurements, including FT-IR, TGA, Raman spectroscopy, and battery performance assessments, confirmed the successful synthesis and positive effects of PMGC. Results indicated that a 0.5% addition of PMGC led to reduced internal resistance and enhanced fast charging and discharge capacity. However, excessive PMGC adversely affected aging and self-discharge. The study provides valuable insights into optimizing PMGC content for improved lithium battery performance, presenting potential advancements in energy storage systems and electric vehicles.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Heat dissipation from Li-ion batteries is a potential safety issue for large-scale energy storage applications. Maintaining low and uniform temperature distribution, and low energy consumption of the battery storage is very important. We studied the fluid dynamics and heat transfer phenomena of a single cell, 16-cell modules, battery packs, and cabinet through computer simulations and experimental measurements. The results show that the temperature distribution of single cell is relatively uniform when the cell is facing the air flow. In a module, very high air flow rate and large gap between the cells can reduce the cell temperature. A pack with a good thermally conductive case is very important to ensure good heat dissipation of the battery module. Due to limited space in the cabinet, additional air inlets and outlets can be opened outside of the cabinet to slightly lower the pack temperature. Installing fins outside the cabinet can also slightly reduce the temperature inside the cabinet. Liquid cooling medium, such as water, is much better than the air-cooling medium.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Sanctuaries devoted to Asclepius were established and operated for almost a thousand years in various Greek and Roman cities throughout the Mediterranean region. The Asclepieion sanctuary in Lenta (formerly known as Ancient Lebena) in Crete was famous for receiving water from a sacred spring. In the Ancient Lebena, Levinaion was a famous centre for hydrotherapy, physiotherapy and a psychiatric hospital. In the present paper, we aim to assess the hydrochemical status of this sacred spring that holds a prominent position in archaeological and historical studies. The main objectives of this study are: Initially, to present supervisory evidence (archaeological, geological, hydrochemical) of an area that was a water resource management model for many centuries, carrying out therapeutic work. The second objective is to present and compare hydrochemical data in the last century, i.e. from 1915 to 2021. The third objective is to highlight and warn of an incipient saltwater intrusion in the area along the Lentas coast. The fourth objective is to propose an alternative and sustainable form of water resources management in the region that requires the study and rational utilization of the sporadic small water springs in the region. Our study focuses on a basic hydrochemical analysis of spring and borehole water in the remains of Levinaion in the Lentas region and their comparison with spare historical data of the sacred spring water, aiming to interpret the impact of the changes in the spring water resources that occurred in the last decades due to urban modernization. Our results highlight (i) visible fluctuations in chemical composition of borehole water samples, (ii) a neutral to alkaline pH in borehole waters, and an alkaline pH in spring waters, (iii) un-detectable arsenic of Lentas borehole water, unlike historical data of Lentas spring water, (iv) low values of dissolved radon of Lentas borehole water and spring water of Kefalovrysa, and (v) a timeless constant and hypothermic nature of the water of both sacred spring and borehole of Lenta, but also of Kefalovrysa spring. The recorded historical data, i.e. from 1915 to 1957, due to the absence of substantial anthropogenic activity in the area, can be used as reference values (natural background levels, NBLs) for the Lentas area. Our findings emerge with the need to bring again the flowing spring water of the sacred spring of Lentas in its original form through sustainable management and re-discover its beneficial therapeutical effects.

Passive balancing is a traditional choice for lithium-ion battery packs although it is regarded as highly inefficient. One opportunity to improve traditional balancing in sub-medium size battery packs is to combine two balancing methods: passive and active. Statistical analysis have been performed to rationalize battery pack division in smaller packs and use of higher level selective charging method to decrease losses of passive balancing. An experimental balancing prototype have been designed and tested for efficiency. Results indicate energy performance degradation if cells of the pack are with low capacity variation. Proposed balancing approach could improve performance under high cell mismatch conditions.

The precise determination of the State-of-Health (SOH) of lithium-ion batteries is critical in the domain of battery management systems. The proposed model in this research paper emulates any deep learning or machine learning model by utilizing a Look Up Table (LUT) memory to store all activation inputs and their corresponding outputs. The operation that follows the completion of training is referred to as the LUT memory preparation procedure. The lookup operation performed on this method simply substitutes for the inference process. This is achieved by discretizing the input data and features before binarizing them. The term for the aforementioned operation is the LUT inference method. The procedure was evaluated in this study using two distinct neural network architectures: a bidirectional long short-term memory (LSTM) architecture and a standard fully connected neural network (FCNN). It is anticipated that considerably greater efficiency and velocity will be achieved during the inference procedure when the pre-trained deep neural network architecture is inferred directly. The principal aim of this research is to construct a lookup table that effectively establishes correlations between the SOH of lithium-ion batteries and ensures a degree of imprecision that is tolerable. According to the results obtained from the NASA PCoE lithium-ion battery dataset, the proposed methodology exhibits performance that is largely comparable to that of the initial machine learning models. Utilising the error assessment metrics RMSE, MAE, and (MAPE), the accuracy of SOH prediction has been quantitatively evaluated. The indicators mentioned above demonstrate a significant degree of accuracy when predicting SOH.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

Innovations in drug delivery systems are crucial for enhancing therapeutic efficiency. Our research presents a novel approach based on Electro-fluid dynamic atomization (EFDA) to fabricate core-shell monophasic particles (CSMp) from sodium alginate blends of varying molecular weights. This study explores the morphological characteristics of these particles in relation to material properties and process conditions, highlighting their potential in drug delivery applications. A key aspect of our work is the development of a mathematical model that simulates the release kinetics of small molecules, specifically sodium diclofenac. By assessing the diffusion properties of different molecules and gel formulations through transport and rheological models, we have created a predictive tool for evaluating the efficiency of these particles in drug delivery. Our findings underscore two critical independent parameters for optimizing drug release: the external shell thickness and the diffusivity ratios within the dual layers. This allows for precise control over the timing and intensity of the release profile. The study advances our understanding of EFDA in the fabrication of CSMp and offers promising avenues for enhancing drug delivery systems by tailoring release profiles through particle characteristic manipulation.

The present study focused on the development of gel-based capsules from sodium alginate and different berries fresh juice: chokeberry, sea buckthorn, and blueberry. Obtained through extrusion method, the macrocapsules were added into yoghurt, a well-known and consumed dairy product. In order to establish the changes that can occur into the food product, the samples were tested during 7, respectively 15 days storage in refrigeration conditions. According to the results, the antioxidant activity increased during storage and gels can represent a good option for bioactive substances’ encapsulation. Sensorial analysis performed indicated that consumers are open to consuming yoghurt berries capsules and, according to the results observed into scientific literature, they no longer rejected the product due to bitterness and sourness of sea buckthorn or aronia.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

In this work, a colorimetric indicator based on gold nanoparticles (AuNP) and a biodegradable and eco-friendly polymer (sodium alginate, Alg.), has been developed, for the real-time detection of fish spoilage products. AuNP and colorimetric indicator were characterized by: UV-Vis, FTIR spectroscopies, TGA, DSC, XRD, TEM, and colorimetry. The UV-Vis spectrum and TEM showed the successful synthesis, the spherical shape, and the size of AuNPs. Results indicated color changes of the indicator in packaged fish on day 9 of storage at refrigerated temperature (5ºC). These results showed the successful application of colorimetric indicator in the detection of TVB-N in packaged fish.

In a Water-Cooled Lithium-Lead (WCLL) Breeding Blanket (BB), the heat generated by the plasma thermal radiation and nuclear reactions is removed mainly by two components; namely, the First Wall (FW) and the Breeding Zone (BZ). The FW faces the neutrons and charged particles fluxes generated by the fusion reactions and the thermal radiation coming from the plasma. The present work takes into account the FW cooling system inspired by the WCLL BB 2018 design of DEMO 2017 baseline. Unlike the baseline where a Pressurized-Water Reactor (PWR) setup is used for the coolant, various setup between the Boiling Water Reactor (BWR) and the High-Pressure (HP) BWR are studied in the present work operating in the Two-Phase Flow (TPF) regime. The 3D model of the FW in the WCLL BB 2018 design is simplified into a 1D model and a steady state analysis is carried out to optimize the mass flow rate of the water and the number of parallel channels at the BB cells at different poloidal locations of the reactor, which helps not only in reducing the used coolant but also in improving the Tritium Breeding Ratio (TBR). The present work takes into account forced convection in the liquid only region, the subcooled boiling region, and the saturated boiling region using suitable empirical or semi-empirical models from the literature. The results are validated against the existing results in the literature. In the end, related conclusions are made regarding the pros and cons of the studied operating conditions.

Deficient wound healing is frequently observed in patients diagnosed with diabetes, a clinical complication that compromises mobility and leads to limb amputation, decreasing patient autonomy and family lifestyle. Fibroblasts are crucial for secreting the extracellular matrix to pave the wound site for endothelial and keratinocyte regeneration. The biosynthetic pathways for collagen production are one of the main components of the extracellular matrix, as the crosslinking of extracellular collagen fibers is intimately related to fibroblast redox homeostasis. In this study, human dermic fibroblasts were cultured with 1 mM sodium selenite (inorganic) and 1 mM of two selenium amino acids (organic), Se-cysteine and Se-methionine. This concentration was compatible with long-term exposure necessary for extracellular matrix production and allowed us to examine the impact of these three compounds on the state and response of the thiol-based HyPer biosensor expressed in the cytoplasm. In addition, the abundance of extracellular matrix and ultrastructural properties were evaluated by Picrus Sirius red staining and scanning electronic microscopy, respectively. We also evaluated whether these selenium compounds effectively ameliorated the perturbations induced by culturing fibroblasts at high glucose levels (25 mM) regarding cytoplasmic redox, extracellular matrix, and glycation on collagen fibers. Our results indicate that cytoplasm protein oxidation was sensitive to selenium compound supplementation. Selenium amino acids increased the sensitivity to protein oxidation, and only Se-cysteine increased the disulfide bond reduction in fibroblasts maintained in high glucose. Despite the lack of effect of selenium compounds on the glu-cose-induced increase in matrix fiber thickness, we found that endothelial migration improved in the matrix generated by high glucose-cultured fibroblasts.

The application of chitosan and alginate coatings for Ready-to-Eat (RTE) baked fish product were studied. An experimental design was used to investigate the effect of coating polysaccharide concentration and glycerol addition on the safety (microbial growth), and quality (water loss and lipid oxidation) of RTE seafood product under optimal, and abused storage conditions. The results showed that a chitosan coating with 1% (w/v) chitosan in 1% (v/v) acetic acid, and 15% (w/w chitosan) glycerol, or 1% (w/v) alginate coating with no glycerol, and no crosslinking showed the best performance in controlling the tested safety and quality parameters. Desirability method was used to identify the shelf life of chitosan, alginate and double coated RTE products. Whereby, chitosan coated samples showed the best performance with a third fold shelf life extension compared to uncoated products.

In this study, we investigated the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material by coating it with ZnO and examined the changes in surface composition using X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analysis. Furthermore, we investigated the electrochemical properties, including discharge capacity and initial irreversible capacity, of the modified materials. The results revealed that ZnO predominantly existed on the material surface, exerting influence on both surface composition and electrochemical characteristics. As the ZnO coating amount increased, the nickel and manganese content on the material surface also increased, and heat treatment at 400 °C resulted in the formation of composite oxides of transition metals and zinc on the material surface. The bonding energy of transition metals increased, and ZnO coating at a mass fraction of 2 % effectively suppressed irreversible reactions around 3.6 V at 55 °C, thereby improving initial coulombic efficiency. Battery materials coated with 2% ZnO exhibited optimal discharge capacity and cycle life at 55 °C/0.5 C.

To overcome the difficulty of separating bastnaesite from fluorite through the flota-tion technique, the present study examined the suitability of sodium alginate (SA) as a depressant in the flotation process. The effect of SA on the flotation separation of bastnaesite and fluorite was evaluated using micro-flotation tests, zeta potential meas-urements, adsorption density measurements, Fourier infrared spectroscopy, and X-ray photoelectron spectroscopy. The micro-flotation results showed that SA exerted a strongly detrimental effect on fluorite flotation, while slightly affecting bastnaesite flotation. The surface chemistry results revealed that the -COO- and HO- functional groups in SA coordinated with Ca2+ on the fluorite surface, which induced hydro-philicity and hindered the adsorption in the subsequent collector. However, the inter-action of SA with the bastnaesite surface was marginal and did not affect the anchor-ing of the collector on the surface of bastnaesite. Based on these results, the present study proposes a possible model for the interaction of SA on the surfaces of the two minerals, laying a foundation for the flotation separation of bastnaesite from fluorite with SA as an environmentally benign depressant.

Cathode materials play a key role in the development and application of lithium-ion batteries, but the unfavorable factors such as structural phase transformation and low conductivity in the cycling process restrict the further improvement of battery performance, so the development and modification of high-performance cathode materials is a current research hotspot. LiNixCoyMn1-x-yO2(x≥0.6), a high-nickel cathode material, has the advantages of high platform potential, high energy density and low cost, and is an ideal material to achieve the goal of 300 Wh kg-1 and above for batteries. However, its poor thermal stability, poor interface stability, safety and life cannot meet the requirements of current power batteries. In this paper, the research status of high-nickel cathode materials is introduced, including bulk doping and surface coating, and the modification method of doping and coating integration is also introduced. Finally, we put forward the prospect of the future development trend of high-nickel cathode materials.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

The severe volumetric expansion of silicon nanoparticles (~400 %) limits their practical application as an anode material for next-generation lithium–ion battery (LIB). Here, we describe the fabrication and characterization of conformal polydopamine carbon shell encapsulating rattle-type silica@silicon nanoparticles (PDA−PEI@PVP−SiO2@Si) with tunable void structure prepared following a dual SiO2 template using (3–aminopropyl)triethoxysilane (APTES) as a self-catalytic, structure-directing agent to tetraethyl orthosilicate (TEOS) pretreated with polyvinylpyrrolidone (PVP K30) via modified Stöber process. Polyethylene imine (PEI) crosslinking facilitated the construction of interconnected three-dimensional bubble wrap-like carbon matrix structure through hydrothermal treatment, pyrolysis, and subsequent surface-protected etching. The composite anode material delivered 539 mAh·g−1 capacity after 100 cycles at 0.1 A·g−1, and 453 mAh·g−1 rate performance at 5 A·g−1. The satisfactory electrochemical performance of the PDA−PEI@PVP−SiO2@Si was attributed to the following: the rattle-type structure providing void space for Si volume expansion, PVP K30-pretreated APTES/TEOS SiO2 seeds via catalyst-free, hydrothermal-assisted Stöber protecting Si/C spheres upon etching, carbon coating strategy increasing Si conductivity while stabilizing the solid electrolyte interface (SEI), and PEI carbon crosslinks providing continuous conductive pathways across the electrode structure. The present work realizes a promising strategy to synthesize the tunable yolk–shell C@void@Si composite anode materials for high power/energy-density LIB applications.

This review explores the potential implementation of lithium tetraborate (Li2B4O7) as a scintillator medium for neutron detection applications. Several characteristics required for the neutron detection process suggest that Li2B4O7 could be a suitable material for scintillation-based neutron detection systems. The inherently large neutron capture cross-section due to 10B and 6Li isotopes, and the ease with which Li2B4O7 can be enriched with these isotopes, combined with the facile inclusion of rare-earth dopants are all expected to improve luminescent properties as well as neutron detection efficiency of Li2B4O7. The electronic structure of doped and undoped Li2B4O7 are explored using photoemission and inverse photoemission spectroscopies, optical measurements, and theoretical computational studies such as density functional theory. The scintillation properties are further enhanced because of the wide bandgap, and transparency towards the photons that are emitted following neutron capture.

Various iron oxides have been proven to be promising anode materials for metal-ion batteries due to their natural abundance, high theoretical capacity, ease of preparation, and environmental friendliness. However, the synthesis of iron oxide-based composites requires complex approaches, especially when it comes to composites with intrinsically conductive polymers. In this work we propose a one-step microplasma synthesis of a polyaniline-coated urchin-like FeOOH nanoparticles (FeOOH/PANI) for application as anode in lithium-ion batteries. The material shows excellent electrochemical characteristics, providing initial capacity of ca. 1600 mA∙h∙g−1 at 0.05 A∙g−1 and 900 mA∙g−1 at 1.2 A∙g−1. Further cycling lead to capacity decrease to 150 mA∙h∙g−1 by the 60th cycles, followed by a recovery that maintained the capacity at 767 mA∙h∙g−1 after 2000 cycles at 1.2 A∙g−1 and restored full initial capacity of 1600 mA∙h∙g−1 at low current density of 0.05 A∙g−1. Electrochemical milling of the material caused such interesting behavior of the material, and we confirmed this phenomenon by a combination of physico-chemical and electrochemical techniques. The anodes also exhibit high performance in a full cell with NMC532. NMC532//FeOOH/PANI full cell provided energy density of 224 Wh∙kg−1 which is comparable to the reference cell with graphite anode (264 Wh∙kg−1).

The research aims to resolve water pollution generated by dye wastewater. In this paper, the aminated sodium lignosulfonate (AELS) was prepared through the Mannich reaction, and the synthesis conditions were optimized using orthogonal experiments to determine the best amination conditions. The successful preparation of AELS was demonstrated through the use of FT-IR, XRD, TG, SEM and XPS characterization techniques. Then, the adsorption capacity of Methyl blue (MB) by AELS was compared in a range of different circumstances, like pH, adsorbent dose, initial concentration, time, and temperature. Additionally, the kinetics, isotherms, and thermodynamic properties of the AELS adsorption for MB were studied and discussed. The results indicated that the fitting results were consistent with the pseudo-second-order kinetic model and Langmuir isotherm model, in accordance with the mechanism of single-molecular-layer chemisorption. And the adsorption of MB by AELS was a spontaneous and endothermic process. Upon completion of five adsorption experiments, the adsorption capacity of MB by AELS was determined to be 107.95 mg g-1, which was 5.3% lower than the first experiment. This research promotes the effective use of natural resources and allows for the sustainable use of lignin and the advancement of new applications for it.

Lithium-ion batteries with improved energy densities have made understanding the Solid Electrolyte Interphase (SEI) generation mechanisms that cause mechanical, thermal, and chemical failures more complicated. SEI processes reduce battery capacity and power. Thus, a review of this area's understanding is important. It is essential to know how batteries degrade in EVs to estimate battery lifespan as it goes, predict, and minimize losses, and determine the ideal time for a replacement. Lithium-ion batteries used in EVs mainly suffer two types of degradation: calendar degradation and cycling degradation. Despite the existence of several existing works in the literature, several aspects of battery degradation remain unclear or have not been analyzed in detail. This work presents a systematic review of existing works in the literature. The results of the present investigation provide insight into the complex relationships among various factors affecting battery degradation mechanisms. Specifically, this systematic review examined the effects of time, side reactions, temperature fluctuations, high charge/discharge rates, depth of discharge, mechanical stress, thermal stress, and the voltage relationship on battery performance and longevity. The results revealed that these factors interact in complex ways to influence the degradation mechanisms of batteries. For example, high charge currents and deep discharges were found to accelerate degradation, while low temperatures and moderate discharge depths were shown to be beneficial for battery longevity. Additionally, the results showed that the relationship between cell voltage and State-of-Charge (SOC) plays a critical role in determining the rate of degradation. Overall, these findings have important implications for the design and operation of battery systems, as they highlight the need to carefully manage a range of factors to maximize battery performance and longevity. The result is an analysis of the main articles published in this field in recent years. This work aims to present new knowledge about fault detection, diagnosis, and management of lithium-ion batteries based on battery degradation concepts. The new knowledge is presented and discussed in a structured and comprehensive way.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Bacteriotherapy is emerging as a strategic and effective approach to treat infections by providing putatively harmless bacteria (i.e., probiotics) as antagonists to pathogens. A proper delivery of probiotics or their metabolites (i.e., post-biotics) can avail itself of biomaterial encapsulation by innovative manufacturing technologies. This review paper aims at providing the most recent biomaterial-assisted strategies proposed to treat infections or disbiosis using bacteriotherapy. We revised the encapsulation processes across multiscale biomaterial approaches, which could be ideal to target different tissues and suit diverse therapeutic opportunities. Hydrogels, and in particular polysaccharides, are the focus of this review, as they have been reported to better sustain vitality of the live cells incorporated. Specifically, the approaches for fabricating hydrogel-based devices with increasing dimensionality (D), namely, 0D (i.e., particles), 1D (i.e., fibers), 2D (i.e., fiber meshes), and 3D (i.e., scaffolds) endowed with probiotics, were detailed by describing their advantages and challenges, along with a future overlook in the field. Electrospinning, electrospray and 3D bioprinting were investigated as new biofabrication methods for probiotic encapsulation within multidimensional matrices. Finally, examples of biomaterial-based systems for cell and post-biotic release were reported.

MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

In this paper we present textural and compositional data for columbite group minerals (CGM) and associated Nb-Ta-Sn oxides from lithium-beryllium-tantalum pegmatite deposits of the Kolmozero-Voronja belt, NW Russia, with the aim of deciphering the above mentioned features for minerals from deposits with different mineral signatures and lithium ore grade. Minerals from four deposits, including two of world-class (Kolmozero and Polmostundra), are examined. It is shown that the main controlling factors are the diversity and rate of magmatic fractionation, hydrothermal overprint and mineral paragenesis followed from the specific geochemical signature of the different pegmatite deposits. CGM from Kolmozero include several mineral species (columbite-(Fe), columbite-(Mn), tantalite-(Fe), tantalite-(Mn)) showing large compositional variations, mainly controlled by Nb-Ta fractionation (Ta/(Ta+Nb) = 0.16-0.70; Mn/(Mn + Fe) = 0.45-0.63). Textural patterns are extremely various (oscillatory, homogeneous, patchy, spongy, somewhere with over-growing Ta-rich rims) and indicate the involvement of numerous magmatic and hydrothermal processes. The Polmostundra CGM are represented by columbite-(Fe) with Ta/(Ta+Nb) ranging from 0.05 to 0.39 with homogeneous, mottled, oscillatory, patchy and irregular reverse textures. The Okhmylk CGM are irregular normal, patchy and homogeneous columbite-(Fe) and columbite-(Mn) with Ta/(Ta+Nb) = 0.09-0.24 and Mn/(Mn + Fe) = 0.29-0.92, indicating the suppressed magmatic fractionation and iron drop due to precipitation of Fe minerals. Columbite-(Fe) and columbite-(Mn) from the Be-Ta Shongui deposit are less evolved with Ta/(Ta+Nb) = 0.07-0.23 and Mn/(Mn + Fe) = 0.31-0.55. The minerals are characterized by progressive normal, oscillatory, homogeneous and ir-regular reverse patterns. Associated pyrochlore minerals occur both as early magmatic (Kolmozero) and late hydrothermal (Polmostundra, Okhmylk). Cassiterite is found only in the Okhmylk dykes and is apparently of hydrothermal origin. CGM from Li pegmatites have impurities of Ti (0.01-0.05 apfu) and W (up to 0.02 apfu), whereas CGM from Be pegmatites contains elevated Ti (up to 0.09 apfu). The mineral systems analysis presented here is relevant for exploration.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

The effect of chemical degradation of a sodium alginate solution and the possibility of encapsulation of paprika oleoresin were investigated. To produce sodium alginate oligomers, a depolymerization process was performed using hydrogen peroxide as a decomposition factor. The characteristics of the samples were obtained by measuring the contact angle of the surface, the surface tension of solutions, as well as thermal decomposition in thermo - gravimetric analysis. The obtained solution of alginate oligomers served as the carrier material for immobilization of capsaicin. Capsules were prepared by ionic gelation using a calcium chloride solution as a crosslinking agent. In this way, capsules without and with the core (capsaicin) were prepared and their ability to scavenge free radicals (DPPH) and iron-reducing properties (FRAP) were determined. The stability of the capsules was examined under conditions of the gastric and small intestine. It was found that alginate oligomers can be used in the encapsulation of bioactive compounds and the efficiency is above 80%. Capsule production from alginate oligomers affected their thermal stability. The use of alginate derivatives as a carrier increases the antioxidant properties of the finished product, as well as its ability to reduce iron ions. The use of alginate oligomers as a coating material prevents the active substance from being released too early in the conditions of the small intestine, prolongs the stability of the capsules, and supports their durability in gastric conditions.

Irrigation is crucial in cleaning and disinfection of the root canal system, because endodontic instruments are unable to reach a large part of the root canal system (isthmuses, accessory canals, apical ramifications) and bacteria that can reside. Sodium hypochlorite (NaOCl) is currently used as irrigant in root canal therapies for its non-specific protheolytic and antimicrobial properties, but undesirable effects may be observed especially when used near the terminus of apical foramen. This study aims to evaluate antimicrobial properties of Thyme Essential Oil (TEO) used alone or in combination with NaOCl against different bacterial strains, especially Staphylococcus aureus and Streptococcus mutans. TEO non-cytotoxic concentration (9,28mg/mL) showed antimicrobial properties comparable to NaOCl after 1min of contact, both in presence of organic material (6% sheep blood). Moreover, the combination of TEO and NaOCl did not compromise their individual antimicrobial properties at the same time of contact. These data suggest that TEO could be used as antimicrobial irrigant in root canal therapies in association with NaOCl, to reduce concentration of NaOCl and its undesirable side effects. Due to the absence of cytotoxic effects at tested dilution, TEO could be safely used also near the terminus of apical foramen for its cytocompatibility.

In this work we present a versatile, rapid, and low-cost manufacturing technique to develop bioceramic scaffolds that could enhance bone tissue regeneration via microwave preparation using a commercial microwave oven. The scaffolds were prepared combining hydroxyapatite and water glass (sodium trisilicate solution), foamed by using a microwaves oven and then characterized by means of SEM-EDS, mechanical properties, infrared spectroscopy (ATR-FTIR), density and stability test in water. Furthermore, in vitro tests were performed to verify the affinity of osteoclast cells versus the so prepared scaffold. The morphology of the samples showed interconnected pores suitable for promoting tissue regeneration and vascularization while specific mechanical properties were preserved. The physicochemical characterization and the in vitro tests presented promising results for bone regenerative applications.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

Clear cell renal cell carcinoma (ccRCC) is the most frequent form of kidney cancer. Metastatic stages of ccRCC reduce the five-year survival rate to 15%. In this report we analyze the ccRCC-induced remodeling of the five KEGG-constructed excretory functional pathways in a surgically removed right kidney and its metastasis in the chest wall from the perspective of the Genomic Fabric Paradigm (GFP). GFP characterizes every single gene in each region by the independent variables: average expression level (AVE), relative expression variability (REV) and expression correlation (COR) with each other gene. While traditional approach is limited to only AVE analysis, the novel REV analysis indicates genes whose correct expression level is critical for cell survival and proliferation. COR analysis determines the real gene networks responsible for functional pathways. The analyses covered the pathways: aldosterone-regulated sodium reabsorption, collecting duct acid secretion, endocrine and other factor-regulated sodium reabsorption, proximal tubule bicarbonate reclamation, and vasopressin-regulated water reabsorption. The present study confirms the conclusion of our previously published articles on prostate and kidney cancers that even equally graded cancer nodules from the same tumor have different transcriptomic topologies. Therefore, the personalization of the anti-cancer therapy should go beyond the individual to his/her major cancer nodules.

This article presents a review of resources for batteries with a specific focus on sustainability aspects related to raw materials, electrode and electrolyte chemistries suitable for the automobile industry. We emphasize the importance of prioritizing sustainability in battery technology evolution, which is expected to shift towards earth-abundant materials. One notable advancement in this direction is the utilization of glass solid-state electrolytes, known for their high ionic conductivity, low electronic conductivity, and high dielectric constant. However, our review suggests that further research should explore synthesis methods to modify anisotropic properties, enhancing the performance of solid-state electrolytes, particularly in facilitating the flow of ions.

A full electrification of many local railway lines is often not feasible or sustainable in terms of construction and maintenance costs or alternatively for the presence of additional constraints and limitations deriving from environmental or infrastructural limitations. Battery Operated or other kind of hybrid solutions powertrains are currently proposed as sustainable alternatives to Internal combustion engines for the propulsion of rolling stock on not electrified lines. In this work, authors propose the adoption of a partial electrification of lines to assure higher performances and reliability of battery-operated rolling stock designed to be recharged and feed using standard technologies such as pantographs gathering power from suspended catenaries. This innovative solution is designed for a benchmark test vehicle inspired from an existing one and simulated considering some possible scenario of application corresponding to some existing railway lines in Italy.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

Many studies have been conducted using pectin for modified drug delivery. In this regard, the goal of the work was to obtain interpolyelectrolyte complexes based on citrus or apple pectin and the Eudragit® EPO and study properties from the standpoint of using these carriers for oral drug delivery. Turbidity, gravimetry, viscosity, elementary analysis and FTIR spectroscopy, DSC analysis were used for physicochemical characterization. Diffusion-transport characteristics were studied to assess the swelling ability of the matrices and the release of diclofenac sodium. Mathematical modeling of the release parameters was carried out using the Krosmayer-Peppas equation. During the turbidity study, stoichiometry compositions were selected for the studied IPECs EPO/PeсA and EPO/PeсC at pH values = 4.0, 5.0, 6.0, 7.0. FTIR spectra of the complexes are characterized by an increase in the intensity of the bands at 1610 cm-1 and 1400 cm-1. According to the DSC analysis IPEC has a certain Tg = 57.3°C. The highest release rates are shown by IPEC EPO/PecC_1 and EPO/PecC_4. The mechanism of drug transport from the matrices IPEC EPO/PecC, IPEC EPO/PecA_3 and EPO/PecA_4 can be characterized as Super Case II. Anomalous (non-Fickian release) is typical for IPEC EPO/PecA_1 and EPO/PecA_2. Thus, the resulting systems are suitable for colon-specific drug delivery systems.

An inorganic solid electrolyte is the most favorable candidate for replacing flammable liquid electrolytes in lithium batteries. Lithium Lanthanum Zirconium Oxide (LLZO) is considered as a promising solid electrolyte due to its safe operating potential window (0-5V) combined with its good electrochemical stability. In this work, 250 g batches of pre-sintered Tadoped (Li7La3Zr1.6Ta0.4O12, TaLLZO) were synthesized for bulk production of dense LLZO electrolyte. A simple two-step thermal treatment process was developed. The first thermal step at 950 °C initiates nucleation of LLZO carefully controlling process parameters such as heating atmosphere, temperature and dopant concentration. In the second thermal step at 1150 °C, sintered discs were obtained as solid electrolytes, with relative densities of 96%. X-ray diffraction analysis confirmed the phase purity of the sintered TaLLZO disc, and refined data was used to calculate the lattice parameter (12.944 Å). Furthermore, the presence of the Ta dopant in the disc was confirmed through X-ray photoelectron spectroscopy (XPS) analysis. The ionic and electronic conductivity values of TaLLZO disc were 104 S cm-1 and 10-10 S cm-1, respectively. These values confirm that the prepared (Ta-LLZO) discs exhibit ionic conductivity while being electronically insulating, being suitable for use as solid electrolytes with the requisite electrical properties.

In this study, ignition delay and burning rate are experimentally investigated in relation to the effect of pristine carbon nanotubes (CNTs), sodium dodecylbenzene sulfonate (SDBS), and diesel blends. Single droplet combustion tests were conducted in a combustion system for 21 days using CNTs at concentrations of 50 ppm and 100 ppm, that were dispersed in Colombian commercial diesel and stabilized by SDBS. Additionally, recordings of the combustion were collected, and the Shadowgraph optical method was utilized for monitoring the evolution of droplet size during combustion. The measurements were done over a four-week period. The results demonstrated that the temporal stability has a direct impact on the single droplet combustion tests because a concentration of CNTs of 100 ppm showed higher stability than those achieved by 50 ppm. Consequently, improvements were found with a concentration of 100 ppm, for instance, thermal conductivity increased by about 20%, ignition delay time by 16.2%, and burning rate by 30.5%.

In this study, sodium alginate (SA) was oxidized with potassium periodate to produce an alginate-based tanning agent. Using OSA as a biodegradable tanning agent and a nano-hydroxyapatite (nano-HAp) low concentration suspension to give flame retardancy to leather, eco-design concepts were applied to establish a chrome-, aldehyde-, and phenol-free tanning process. Micro-DSC, 1H NMR, attenuated total reflection mode Fourier transform infrared spectroscopy (FTIR-ATR), and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) were used to investigate the complex matrix collagen-OSA-nano-HAp. Micro-differential scanning calorimetry (micro-DSC) was used to assess OSA's ability to interact with collagen and stabilize the collagen-OSA matrix, while 1H unilateral nuclear magnetic resonance (NMR) was used to investigate the aqueous environment and limitations around collagen molecules caused by their association with OSA and nano-HAp. Industrial standard tests were used to assess mechanical properties and fire resistance of the new leather prototype. The findings reported here indicate that both OSA and nano-HAp are suitable alternatives for cleaner tanning technologies and more sustainable leather.

Permeability has an important effect on drug absorption. In this study, the effect of different concentrations of sodium sulfobutyl ether-β-cyclodextrin (SBE-β-CD) on the absorption of ranitidine was investigated to examine the mechanism of permeability changes. The results of parallel artificial membrane permeability assay (PAMPA) showed that increasing the concentration of sodium sulfobutyl ether-β-cyclodextrin, 0, 0.12% (w/v), 0.36% (w/v) and 3.6% (w/v), respectively, the apparent permeability coefficient of ranitidine decreased to 4.62×10-5 , 4.5×10-5 , 3.61×10-5 and 1.08×10-5 in Caco-2 cells, respectively. The same results were obtained from oral pharmacokinetic study in rats; Further studies indicated that SBE-β-CD significantly increased the zeta potential of ranitidine. SBE-β-CD interacted with ranitidine charges to form a complex that reduced ranitidine permeability, and SBE-β-CD should be chosen with caution for drugs with poor permeability.

The demand for high-energy-density batteries necessitates novel anode materials. Transition metal oxides (TMOs) show promise due to their high capacity, sustainability, and cost-effectiveness. However, TMO-based anodes face challenges related to expansion and conductivity. This study presents a two-step dilution crystallization method to fabricate porous ZnO nanoflowers at a moderate temperature. In-situ integration with carbon nanotube dispersants enhances conductivity and reduces agglomeration. The resulting composite anode exhibits impressive initial discharge capacity (2314.2 mAh g-1) and cycling stability (580.5 mAh g-1 over 50 cycles). This study provides a facile approach for next-generation anode materials.

A two-step, one-pot synthesis of 3-substituted 1H-dibenzo[e,g]indazoles in good to high yields via a LiOtBu-promoted intramolecular cyclization of 2’-alkynyl-biaryl-2-aldehyde N-tosylhydrazones, formed in situ by the reactions of 2’-alkynyl-biaryl-2-aldehydes with p-methylbenzenesulfonohydrazide was developed. Two kinds of hydrogen bonds forming in several products were observed in DMSO-d6 solution in 1H NMR spectroscopic data, which were assigned to the formation of solvated products and dimers of products, supported by the studies of density functional theory (DFT).

Objective: To observe the effect of the combination of fluid-increasing decoction, low molecular heparin sodium and aspirin in the treatment of oligohydramnios in pregnancy. Methods: In this study, 114 pregnant women with oligohydramnios during pregnancy admitted to our hospital between May 2019 and March 2022 were selected as objects, and the pregnant women were equally divided into the observation group and the experimental group by random number table method, with 57 cases in each group. The observation group received conventional fluid infusion, low molecular heparin sodium and aspirin, while the experimental group was treated with fluid-increasing decoction on the basis of the observation group. The treatment effect, S/D level, amniotic fluid index, maximum vertical pocket (MVP), coagulation indexes (plasma prothrombin time (PT), plasma activated partial thromboplastin time (APTT), fibrinogen (FIB)), pregnancy outcome and adverse reactions were compared between the two groups. Results: The total effective rate of treatment was obviously better in the experimental group than that in the observation group (P＜0.05); the S/D level after treatment in the experimental group was remarkably lower than that in the observation group (P＜0.05). The amniotic fluid index and MVP were remarkably higher in the experimental group than in the observation group after treatment (P < 0.05). No significant differences in PT, APTT and FIB were found between the two groups before and after treatment (P > 0.05). The rate of oligohydramnios at delivery, cesarean section rate, neonatal weight status and preterm delivery rate were dramatically better in the experimental group than in the observation group (P < 0.05). Post-partum haemorrhage rate, neonatal asphyxia rate, amniotic fluid contamination rate and incidence of adverse events were not significantly different between the two groups of pregnant women (P > 0.05). Conclusion: The combination of fluid-increasing decoction, low molecular heparin sodium and aspirin is clinically effective and safe in the treatment of pregnant women with oligohydramnios during pregnancy. The combination is effective in reducing the S/D ratio of fetal umbilical blood flow, enhancing the amniotic fluid index and MVP in pregnant women with oligohydramnios during pregnancy, whilst not adversely influencing the coagulation function of the mother, thus contributing to a reduction in the risk of adverse pregnancy outcomes.

Lithium-ion batteries (LIBs) have become indispensable energy storage devices for various applications, ranging from portable electronics to electric vehicles and renewable energy systems. The performance and reliability of LIBs depend on several key components, including the electrodes, separators, and electrolytes. Among these, the choice of binder materials for the electrodes plays a critical role in determining the overall performance and durability of LIBs. This review introduces polymer binders that have been traditionally used in the cathode, anode, and separator materials of LIBs. Furthermore, it explores the problems identified in traditional polymer binders and examines the research trends in next-generation polymer binder materials for lithium-ion battery as alternatives.

This paper investigates the polarization and heat generation characteristics of batteries under different ambient temperatures and discharge rates by means of using a coupled electric-thermal model. The study found that the largest percentage of polarization is ohmic polarization, followed by concentration polarization and electrochemical polarization. The values of the three types of polarization are generally small and stable under normal-temperature environments and low-discharge rates. However, they increase significantly in low-temperature environments and high-discharge rates and continue to rise during the discharge process. Additionally, ohmic heat generation and polarization generation also increase significantly under these conditions. Reversible entropy heat is less sensitive to ambient temperature but increases significantly with the increase of the discharge rate. Ohmic heat generation and polarization heat generation contribute to the total heat generation of the battery at any ambient temperature, while reversible entropy heat only contributes to the total heat generation of the battery at the end of discharge.

Temporal lobe epilepsy is a common, chronic disorder with spontaneous seizures that is often refractory to drug therapy. A potential cause of temporal lobe epilepsy is primary brain injury, making prevention of epileptogenesis after the initial event an optimal method of treatment. Despite this, no preventive therapy for epilepsy is currently available. The purpose of this study was to evaluate the effects of anakinra, lamotrigine, and their combination on epileptogenesis using the rat lithium-pilocarpine model of temporal lobe epilepsy. The study showed that the treated and untreated animals showed no significant difference in the number and duration of seizures. However, the severity of seizures was significantly reduced after treatment. Anakinra and lamotrigine, alone or in combination, significantly reduced neuronal loss in the CA1 hippocampus compared to the control group. However, the drugs administered alone were found to be more effective for CA3 than their combination. The treatment alleviated the impairments in activity level, exploratory behavior and anxiety, but had a relatively weak effect on TLE-induced impairments in social behavior and memory. The efficacy of the combination treatment did not differ from that of anakinra and lamotrigine monotherapy. These findings suggest that anakinra and lamotrigine, alone or in combination, may have clinical utility in preventing epileptogenesis.

The objective of the study was to apply the principles of analytical quality by design (AQbD) to the analytical method for the determination of the radiochemical purity (PQR) of the radiopharmaceutical sodium iodide 131I oral solution, by means of thin layer chromatography (TLC) with a Radio-TLC scanner, the same one that allows to evaluate the quality of the product. For the AQbD, the analytical objective profile (ATP), critical quality attributes (CQA), risk management, the method operable design region (MODR) were defined through the response surface methodology for method optimization using the MINITAB ® software, Control Strategy and the validation of the method where the parameters of selectivity, linearity, precision, robustness, detection limit, quantification limit, range and stability of the sample solution were evaluated. Under the experimental conditions, the conditions of the method were demonstrated by TLC-Scanner and optimization was carried out for an injection volume of 3 µL, radioactive concentration of 10 mCi/mL and carrier volume of 40 µL. It was statistically demonstrated that the method is selective for the 131I iodide band Rf of 0,8 and for the radiochemical impurity IO₃⁻ Rf of 0.6, linearity from 6,0 to 22.0 mCi/mL, intermediate precision with Global RSD of 0,624%, robustness with global RSD 0,101%, detection limit of 0,09 mCi/mL, quantification limit of 0.53 Ci/mL, conforming range, and stability of the sample solution evaluated over time 0, 2 and 20 hours with a global RSD of 0,362%, obtaining consistent results. The development of the method based on AQbD allowed the generation of a design space and an operational space with knowledge of all the characteristics and limitations of the method, likewise in all the operations the conformity of the tests to the acceptance criteria was verified. The validity of our method is concluded under the established conditions, suitable for use in the manufacturing process of sodium iodide 131I and application in nuclear medicine services.

In the recent rechargeable battery industry, lithium sulfur batteries (LSBs) have demonstrated promising candidate battery to serve as the next-generation secondary battery owing to its enhanced theoretical specific energy, economy, and environmental friendliness. Its inferior cyclability, however, which is primarily due to electrode deterioration caused by the lithium polysulfide shuttle effect, is still a major problem for the real industrial usage of LSBs. Optimization of the separator and functional barrier layer is an effective strategy for remedying these issues. In this article, the current progress based on classification and modification on functional separator is summarized. We will also describe their working mechanisms as well as the resulting LSB electrochemical properties. In addition, necessary performance for separators also will be mentioned in order to gain optimized LSB performance.

Feldspar which is one of the main inputs of the ceramic and glass industry has widespread resources in Turkey and holds an outstanding role in exportation. In addition to this, potassium feldspars are one of the suitable resources for the production of potash which is a vital component for agriculture industry. The chlorination technique was used to produce potassium chloride (KCl) from potassium feldspar ore in Kırşehir-Buzlukdağı region. The process of potassium chloride production was carried out with calcination process to decompose potassium feldspar and form potassium chloride while using different kinds of salts such as CaCl2, NaCl, and CaSO4 followed by water leaching process. The recovery from feldspar with 7.21% K2O content was obtained with the 1:1.25:1.5 ratio of Feldspar:CaSO4:NaCl at 1000 °C for 60 minutes followed by leaching. 96.08 % potassium dissolution was achieved.

The necessity to reduce the effect of the greenhouse phenomenon imposed the turn of the food packaging technology to the use of biobased raw materials decreasing the carbon dioxide fingerprint. In this direction alginates derived from brown algae species are of the most promising biobased biopolymers, used for development of edible active coatings, capable to protect food from oxidation/bacterial spoilage. In this study sodium alginate, which was plasticized with glycerol and mixed with a biobased thymol/natural halloysite nanohybrid, was used to develop novel edible active coatings. Active nanocomposite coatings developed by mixing of pure halloysite with sodium alginate/glycerol matrix were produced for comparison purposes. X-Ray and Fourier Transform Infrared Spectroscopy indicated higher compatibility of thymol/halloysite nanohybrid with sodium alginate/glycerol matrix compared to the relevant of pure halloysite. This increased compatibility led to higher tensile properties, water/oxygen barrier properties, and total antioxidant activity. All coating samples were applied as edible active coatings for “tsalafouti” spreadable soft cheese, exhibited a reduction of mesophilic microbial population of more than one log10(cfu/g) unit comparing with uncoated cheese. Moreover, the reduction of mesophilic microbial population was increased by increasing halloysite and thymol content which indicates the sodium alginate/glycerol/thymol/halloysite as promising edible active coatings for “tsalafouti”.

The possibility of deep radiochemical purification of Li2CO3 has been examined in the frame of the purification program of AMoRE collaboration. In this experiment, commercial Li2CO3 was converted into LiNO3. Co-precipitation with inorganic salt-based carriers followed by membrane filtration and sorption using MDM inorganic sorbent methods were tested for the removal of alkaline-earth and transition metals, potassium, magnesium, aluminum, uranium, thorium, and radium. The calcium molybdate-based carrier was the most efficient for removing Th, U, and K. Subsequently, the radium, calcium, and barium contaminations were removed with MDM sorbent. After the impurities’ removal, the final Li2CO3 product was synthesized with NH4HCO3 sludge. The separation factors were derived by means of ICP-MS and HPGe analyses of the initial material, intermediate and final products. The study showed the optimum conditions of co-precipitation and sorption to reach a high yield and radiopurity of lithium carbonate used for low radioactive background experiments.

Arthrospira platensis is a class of microalgae with high economic value. Its high adaptability, high photosynthetic efficiency, and fast growth rate make it one of the few microalgae that can be cultivated on a large scale. Therefore, using the selenium enrichment property of Arthrospira platensis to cultivate selenium-enriched Arthrospira platensis will not only enhance the physiological efficacy of Arthrospira platensis but also increase its economic value significantly. In this study, we investigated the effects of sodium selenite on the growth and photosynthetic performance of Arthrospira platensis selenium by setting different amounts and methods of sodium selenite addition, and we explored the optimal culture conditions. The results showed that the experimental group treated with sodium selenite at 120 mg/L had the fastest growth, and the contents of soluble protein, phycocyanin, and Chlorophyll a increased by approximately 67.9%, 1.44 times, and 38.8%, respectively, compared to the control group. Superoxide dismutase (SOD) and catalase (CAT) activity increased by 1.88-fold and 65%, respectively, and malondialdehyde (MDA) levels were reduced by 62% compared to the control group. The results of the OJIP assay showed that the J and I points were significantly higher at the batch addition and treatment concentration of 120 mg/L, with the rate of QA being reduced and the proportion of the slowly reduced PQ pool being increased. The values of the maximum light energy conversion efficiency (Fv/Fm) per unit of reaction center were higher in both sodium selenite treatment groups than in the control group, indicating that the light energy conversion efficiency of Arthrospira was promoted under all concentration treatment conditions. The batch addition of sodium selenite at concentrations less than 120 mg/L resulted in significantly higher ABS/RC values than the control, and they were far superior to the one-time addition method. The reason for this may have been that the batch addition of sodium selenite at low concentrations increased the light absorption capacity of the unit reaction center of the Arthrospira PSII, resulting in a rise in captured light energy, a rise in the energy captured by the reaction center for electron transfer (ETo/RC), a decrease in the energy dissipated in the absorption of light energy by the reaction center (DIo/RC), and an increase in the photosynthetic performance index (PI abs).

In this study, robust composite solid electrolytes were developed and employed them to enhance the performance of Li-metal batteries significantly. The robust composite solid electrolytes are composed of a soft polymer, poly(ethylene oxide), a Li salt, bis(trifluoromethanesulfonyl)imide (LiTFSI), and super ionic conductive ceramic fillers such as Li1.5Al0.5Ti1.5(PO4)3 (LATP), and Li6.4La3Zr1.4Ta0.6O12 (LLZTO). The main goal of this study is to enhance the electrochemical stability and ionic conductivity. The ionic conductivities of the composite solid electrolytes were found to be 2.08 × 10-4 and 1.64 × 10-4 S cm-1 with the introduction of LATP and LLZTO fillers, respectively. The results prove that the fabricated solid electrolyte was electrochemical stable at voltage exceeding 4.25 V vs. Li/Li+. The internal resistance of the solid electrolyte significantly reduced as compare to gel electrolyte. This reduction can be attributed owing to the alleviation of bulk electrolyte, charge-transfer, and interfacial electrolyte/electrode impedance. When LiFePO4 cathode sheets are coated with a composite solid electrolyte containing LATP powders, the resulting Li-metal battery displays high capacity at 5 C (with a capacity retention of 65.2% compared to the original capacity at 0.2 C) as well as superior cyclic stability and excellent Coulombic efficiency (&gt; 99.5%, over 200 cycles). These results confirm that the composite solid electrolyte acts as a protective layer which have ability to prevent the growth of Li dendrites. Consequently, the fabricated electrolyte configuration can be engineered to enable high energy/power density and electrochemical stable cyclability in Li-metal batteries.

According to WHO, reducing salt intake to less than 5 g/day means less death, disability, and suffering from heart disease and stroke, with around 1.89 million lives saved every year. In this scoping review, we have reviewed the salt consumption pattern of South Asia. For this purpose, we searched online databases and websites and consulted key informants to address relevant unpublished reports. The inclusion criteria are English-language publications between January 2011 and October 2021, as well as research that evaluated salt intake in the South Asian region and reported salt/sodium 24-hr urine or spot urine samples involving at least 100 participants. A total of 2043 studies were screened, out of which 12 studies fulfilled all the criteria. Our review revealed that reported salt intake in the South Asian region ranges from 6.7-13.3 g/day, which was higher than the WHO-recommended maximum level of 5 g/day in all countries. Men consumed more salt than women. This review demonstrates the critical importance of implementing a salt reduction program in South Asian countries.

Burkholderia andropogonis is a severe plant pathogen that can infect more than 50 plant species. Although its genome has been sequenced and annotated, various mechanisms underlying its physiology and pathogenicity remain unknown. Some of these mechanisms can be uncovered through understanding its proteome. In this study, sodium dodecyl polyacrylamide gel electrophoresis (SDS-PAGE) and mass spectrometry analysis were used to profile the proteome of B. andropogonis. Exactly 538 proteins, which belong to 190 protein families performing 88 different functions were identified. The resulting STRING network analysis identified 28 proteins having highly connected interactions with adenosine triphosphate (ATP)-binding-cassette and (ABC) transport system. To the knowledge of the authors, this is the first comprehensive proteomic study on B. andropogonis.