NACA 0015 and NACA 4415 aerofoil are most common four digits and broadly used aerodynamic shape. Both of the shapes are extensively used for various kind of applications including turbine blade, aircraft wing and so on. NACA 0015 is symmetrical and NACA 4415 is unsymmetrical in shape. Consequently, they have big one-of-a-kind in aerodynamic traits at the side of widespread differences of their utility and performance. Both of them undergo the same fluid principle while applied in any fluid medium giving dissimilar outcomes in aerodynamics behavior. On this work, experimental and numerical investigation of each NACA 0015 and NACA 4415 is done to decide their performance. For this purpose, aerofoil section is tested for a prevalence range attack of angle (AOA). The study addresses the performance of NACA 0015 and NACA 4415 and evaluates the dynamics of flow separation, lift, drag, pressure and velocity contour and so on. This additionally enables to layout new optimistic aerofoil, which is critical to enhance the efficiency and performance of an aircraft in terms of lift enhancement and drag reduction.

This paper presents an exact solution to the Timoshenko beam theory (TBT) for first-order analysis, second-order analysis, and stability. The TBT covers cases associated with small deflections based on shear deformation considerations, whereas the Euler–Bernoulli beam theory (EBBT) neglects shear deformations. Thus, the Euler–Bernoulli beam is a special case of the Timoshenko beam. The moment-curvature relationship is one of the governing equations of the EBBT, and closed-form expressions of efforts and deformations are available in the literature. However, neither an equivalent to the moment-curvature relationship of EBBT nor closed-form expressions of efforts and deformations can be found in the TBT. In this paper, a moment-shear force-curvature relationship, the equivalent in TBT of the moment-curvature relationship of EBBT, was presented. Based on this relationship, first-order and second-order analyses were conducted, and closed-form expressions of efforts and deformations were derived for various load cases. Furthermore, beam stability was analyzed and buckling loads were calculated. Finally, first-order and second-order element stiffness matrices were determined.

The importance of vertical jump in sport fields and rehabilitation is widely recognized. Furthermore, Force-Time variables of vertical jump are factors affecting jumping height. Exclusive review of each of this variables, in eccentric and concentric phases, can lead to a specific focus on them during jumping exercises. So, the aims of his study were to a) reviewing the relationship between force-time curve variables of eccentric and concentric phases with jump height and b) description of this variables in Iran national youth volleyball players society. This is an observational study. 12 elite volleyball player (Male, Iran national youth volleyball players, 17±0.7 years) have participated in this study. Correlation between Force-Time variables - included peak force (PF), relative peak force (RPP), peak power (PP), average power (AP), relative peak power (RPP), and Modified Reactive Strength Index (MRSI) - in eccentric and concentric phases and ultimate jump height has been studied. Results showed that the average power (r=0.7) and relative peak force (r=0.75) of concentric phase and MRSI (r=0.83) have significant correlation with ultimate jump height (JH). Relative peak power and average power of concentric phase can massively effect Jump Height in sports like volleyball, which vertical jump is an integral part of them. Focus on both of these factors, which has been studied in this research, in training programs, can improve athlete jump performance significantly.

A new lateral force-resisting wall panel is presented for applications in mid-rise prefabricated lightweight steel construction in seismic prone regions. This panelised system is composed of a hot-rolled frame and cold-formed studs and tracks, which works as a lateral force resisting system in lightweight steel framing. The proposed hybrid panel system exhibits proper ductility and energy dissipation behaviour. The hysteretic responses of full-scale panel experiments demonstrate that the system can safely resist high cyclic loads. The hot-rolled steel part, on the other hand, can significantly improve the initial lateral stiffness of the total system that will control the maximum allowable drift of multi-story buildings. Finally, in a case study, by applying the proposed system to the design of a mid-rise building in a high seismic area, the performance of the hybrid panels, are compared with those of fully hot-rolled systems (moment resisting frames) and fully cold formed systems. The findings indicate that applying hybrid panels will result in lower weights and better performance in seismic prone regions.

To define and evaluate the areas of consideration concerning in identifying the critical factors that top universities in Nueva Ecija, Philippines can be used for triangulating the courses of actions that can be applied to improve the current practices of universities towards its combat to the COVID–19 disease is the primary objective of this study. The researchers used a descriptive design of methodology by using questionnaire–checklist to scientifically describe the situation, problems, phenomenon, or program, or provide information about certain issues related to the virus outbreak. The respondents of the study were faculty and staff of five established universities in Nueva Ecija, Philippines wherein the researchers employed a non–probability sampling technique to be logically assumed as the representative of the entire population. The results of the study shown that the top universities in Nueva Ecija have made efforts to ensure the safety of university workers by complying with the Inter–Agency Task Force (IATF) protocols. It can be inferred, in reality, that there are some areas that must be improved especially when it comes to ensuring the welfare of the personnel who are still reporting to work even in this time of the pandemic. The researchers suggested an enhancement plan that can be adapted by these universities to resolve the concerns of the faculty and staff especially in reducing the spread of the virus without sacrificing the day–to–day transactions of the academic institutions.

Automotive aerodynamics comprises of the study of aerodynamics of road vehicles. Its main goals are reducing drag, minimizing noise emission, improving fuel economy, preventing undesired lift forces and minimizing other causes of aerodynamic instability at high speeds. The Ahmed body has the form of a highly simplified car, consisting of a blunt nose with rounded edges fixed onto a box-like middle section and a rear end that has an upper slanted surface, the angle of which can be varied. It retains vital features of real vehicles in order to study the flow fields around it and the related turbulence models which characterizes the actual flow at elevated Reynolds number. In the present study, the aerodynamic behavior of this body is investigated numerically by the aid of commercial CFD tool: Ansys Fluent. The results of the simulation are validated with available experimental data and results of the simulations from other literatures. The numerical data were obtained for a fixed free stream velocity of 25 m/s at the inlet. The simulations were performed at a fixed slant angle of 25 degree and zero yaw angle. The present study focuses on how local refinement of mesh inside the concerned body and the outside, helps affect the results and for which grid dependency test is the primary objective of this paper. The present study also helps demonstrate how the drag of the body behaves, which is mainly the effect of pressure drag force generated at the rear portion of the body. The study also focuses on important properties like the velocity magnitude at different locations for different meshing cases, and to capture the flow pattern in the front or near the wake region. The study can be further helpful to future researchers in determining resistance, fuel efficiency etc. helping designers to optimize in specialized areas for better efficiency.

A simple, effective and environmental-friendly method was adopted for enhancing the photocatalytic activity of g-C3N4 in the reduction of aqueous Cr(Ⅵ) under visible-light irradiation. The enhancement was achieved via treatment of g-C3N4 in organic solvent with addition of NaOH particles by ultrasonic process for two hours. The results demonstrated that the treated g-C3N4 exhibited much higher photocatalytic activity than pristine g-C3N4 in the reduction of Cr(VI) . Under visible light irradiation for 120 min, the reduced ratios of Cr(VI) with the initial concentration of 50 mg/L in the presence of the treated g-C3N4and pristine g-C3N4 were 100% and 37.1%, respectively. With the addition of fulvic acid, Cr(VI) was efficiently removed at 40 min. Based on the characterization results of the structures and other physiochemical properties of the treated g-C3N4 and pristine g-C3N4 by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and UV Vis diffuse reflectance, the possible reasons responsible for the enhanced photocatalytic activity of the treated g-C3N4 were proposed. The yield and mechanism of different exfoliation methods were compared by semi-quantitative method.

Purpose: National Institute for Health and Care Excellence (NICE) has recently published quality standards for assessment of fall risk and preventing further falls. According to the standards, multifactorial fall risk assessments should include: identification of falls history; analysis of gait, balance, mobility and muscle strength, among other factors. Despite being based on subjective analysis or simple timing and not being multifactorial, physiotherapists and physicians quite often use these tests as reference scales to differentiate between lower and higher risk of falling. Instrumented TUG has been recently reported to provide important additional information to the overall score. Objective: To explore a case-based approach of fall risk assessment to identify the most relevant and informative risk factors that in combination could better define a person risk profile. Materials and Methods: A multifactorial assessment of fall risk through questionnaires, standard functional tests, tests instrumented with inertial sensors, and force platforms has been studied within a group aged 55-80 years old. Different fall risk factors and fall risk assessment methods were analyzed in a case-based descriptive study. Results & Discussion: Subjects at higher risk of falling were identified based on their detailed profiles. A set of features were obtained from the instrumented standard tests differing significantly between subjects presenting higher or lower fall risk. Therefore, instrumenting conventional tests with wearables containing inertial sensors and force platforms gives more detailed and quantitative insights. This information can be used to better define and tailor fall prevention exercises and to improve the follow-up of the evolution of the subject.

The use of haptic devices in rehabilitation of impaired limbs has become rather popular, given the proven effectiveness in promoting recovery. In a standard framework, such devices are used in rehabilitation centers, where patients interact with virtual tasks, presented on a screen. To track their sessions, kinematic/dynamic parameters or performance scores are recorded. However, as Internet access is now available at almost every home, and in order to reduce the hospitalization time of the patient, the idea of doing rehabilitation at home is gaining wide consent. Medical care programs can be synchronized with the home rehabilitation device; patient data can be sent to the central server that could redirect to the therapist laptop (tele-healthcare). The controversial issue is that the recorded data do not actually represent the clinical conditions of the patients according to the medical assessment scales, forcing them to frequently undergo clinical tests at the hospital. To respond to this demand, we propose the use of a bilateral master/slave haptic system that could allow the clinician, who interacts with the master, to assess remotely and in real time the clinical conditions of the patient that uses the home rehabilitation device as the slave. In this paper, we describe a proof of concept to highlight the main issues of such an application, limited to one degree of freedom, and to the measure of the stiffness and range of motion of the hand.

Water and sanitation facilities in sub-Saharan Africa and Africa in general are appalling and for the most part absent. Progress continues with respect to the development of plant materials as potent adsorbents, disinfectants, coagulants, flocculants, wetland species and lots more as substitutes for the dangerous chemical disinfectants. This research presents the potential of phyto-active components of Zanthoxylum zanthoxyloides and Gongronema latifolium as effective biocides against water microbial contaminants. Dry powder of Zanthoxylum zanthoxyloides and Gongronema latifolium were extracted and prepared into different concentrations with ethyl acetate and chloroform, ranging from 25 to 500 mg/ml. These fractions were then examined for antimicrobial activities against inherent bacterial and fungal water contaminants using disc diffusion assay. Fractions were afterwards screened for phytochemical active compounds using standard methods. Crude extracts of the different plant examined selectively comprise saponins, tannins, reducing sugars, anthraquinones, flavonoids, terpenoids, phlobatanins and alkaloids. All plant extracts showed broad spectrum antibiosis against selected gram positive and gram negative bacteria including E. coli, P. aeruginosa, Klebsiella sp, S. pneumoniae and B. cereus, as well as tested fungi, including A. niger, A. flavus, Trichoderma sp and Candida sp. While all extracts exhibited maximum antibiosis at 500 mg/ml, the chloroform extracts compared well than ethyl acetate extracts. The overall results revealed that antimicrobial activities of the plant extracts are dose dependent with comparative activity greater than that of commercial antibiotics at the concentration of extracts tested. E.coli was the most susceptible microbial isolate tested and represents the potential of the extract against a group of coliform which are important indicators of microbial pollution in water. Other microbial isolates also recorded sensitivity to extracts tested at varying degrees. The findings indicate that microbes tested were mostly susceptible to chloroform extract of Z. zanthoxyloides and G. latifolium except for the activity of ethyl acetate extract of Z. zanthoxyloide against E.coli. Results of phytochemical screening of the extract also showed the varied presence of alkaloids, saponins, tannins, flavonoids, terpenoids and anthraquinones The results indicated that plant materials investigated can be developed as effective biocides against water microbial contaminants

The human androgen receptor (AR) is a ligand inducible transcription factor harboring an amino terminal domain (AR-NTD) hosting the ligand independent activation function. AR-NTD is intrinsically disordered and display aggregation properties conferred by the presence of a poly-glutamine (polyQ) sequence of 22 residues. The length of the polyQ sequence, as well as the presence of adjacent sequence motifs modulate this aggregation property. AR-NTD contains also a conserved sequence motif KELCKAVSVSM that displays an intrinsic property to form amyloid fibrils under mild oxidative conditions of its conserved cysteine residue. As peptide sequences with intrinsic ability to oligomerize are reported to have an impact on the aggregation of polyQ tract, we determined the effect of the KELCKAVSVSM on the polyQ stretch in the context of the AR NTD, using Atomic Force Microscopy (AFM). Here, we present evidence for a crosstalk between the amyloidogenic properties of the KELCKAVSVSM motif and the polyQ stretch at the AR NTD.

Nowadays, the Internet of Things (IoT) concept plays a pivotal role in society and brings new capabilities to different industries. The number IoT solutions in areas such as transportation and healthcare is increasing and new services are under development. In the last decade, society has experienced a drastic increase in IoT connections. In fact, IoT connections will increase in the next few years across different areas. Conversely, despite these benefits, several challenges still need to be faced to enable efficient and secure operations (e.g., interoperability, security, standards, and server technologies). Furthermore, although efforts have been made to produce datasets composed of attacks against IoT devices, several possible attacks are not considered. Most existing efforts do not consider an extensive network topology with real IoT devices. The main goal of this research is to propose a novel and extensive IoT attack dataset to foster the development of security analytics applications in real IoT operations. To accomplish this, 33 attacks are executed in an IoT topology composed of 105 devices. These attacks are classified into seven categories, namely DDoS, DoS, Recon, Web-based, Brute Force, Spoofing, and Mirai. Finally, all attacks are executed by malicious IoT devices targeting other IoT devices.

Crosslinking of proteins for their irreversible immobilization on surfaces is a proven and popular method. However, many protocols lead to random orientation and the formation of undefined or even inactive by-products. Most concepts to obtain a more targeted conjugation or immobilization requires the recombinant modification of at least one binding partner, which is often impractical or prohibitively expensive. Here a novel method is presented, which is based on the chemical preactivation of Protein A or G with selected conventional crosslinkers. In a second step, the antibody is added, which is subsequently crosslinked in the Fc part. This leads to an oriented and covalent immobilization of the immunoglobulin with a very high yield. Protocols for Protein A and Protein G with murine and human IgG are presented. This method may be useful for the preparation of columns for affinity chromatography, immunoprecipitation, antibodies conjugated to magnetic particles, permanent and oriented immobilization of antibodies in biosensor systems, microarrays, microtitration plates or any other system, where the loss of antibodies needs to be avoided, and maximum binding capacity is desired. This method is directly applicable even to antibodies in crude cell culture supernatants, raw sera or protein-stabilized antibody preparations without any purification nor enrichment of the IgG. This new method delivered much higher signals as a traditional method and, hence, seems to be preferable in many applications.

A novel fiber optic sensing technology for high frequency dynamics detection is proposed in this paper, specifically tailored for structural health monitoring applications based on strain wave analysis, including both passive impact identification and active Lamb wave monitoring. The sensing solution relies on a fiber optic-based interferometric architecture associated to an innovative coherent detection scheme, which retrieves in a completely passive way the high-frequency phase information of the received optical signal. The optical fiber can be arranged into different configurations in order to meet the requirement of the specific application, the sensor sensitivity being maximized while still ensuring a limited gauge length if a local measure is required. For the active Lamb wave monitoring, this results in a sensing fiber arranged in multiple loops glued on an aluminum thin panel in order to increase the phase signal relative only to the sensing points of interest. Instead, for passive impact identification, the sensitivity is simply increased by exploiting a longer gauge length glued to the structure. The fiber optic coherent (FOC) sensor detects the strain waves emitted by a piezoelectric transducer placed on the aluminum panel or generated by an impulse hammer, respectively. The FOC sensor measurements have been compared with both a numerical model based on Finite Elements and traditional piezoelectric sensors, confirming a very good agreement between experimental and simulated results for both the active and passive impact monitoring scenarios.

The local electrical response in alkaline-doped CuInSe₂ films prepared by single step electrodeposition onto Cu substrates was studied by current sensing atomic force microscopy. The CIS films were prepared from single baths containing the dopant ions (Li, Na, K or Cs) and were studied by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and photocurrent response. Increased crystallinity and surface texturing as the ion size increases was observed as well as enhanced photocurrent response in Cs doped CIS. Li and Na doped films have larger conductivity than the undoped film while the K and Cs doped samples display shorter currents and the current images indicate strong charge accumulation in the K and Cs doped films forming surface capacitors. Corrected CAFM IV curves were adjusted with Shockley equation.

SARS-CoV-2 mRNA vaccination can entail chronic fatigue/dis-autonomy tentatively termed post-acute COVID-19 vaccination syndrome (PACVS). We explored receptor autoantibodies and interleukin-6 (IL-6) as somatic correlates of PACVS. Blood markers determined before and six months after first-time SARS-CoV-2-vaccination of healthy controls (N = 89, 71 females, mean/ median age 39/ 49 years) were compared with corresponding values of PACVS-affected persons (N= 191, 159 females, mean/median age: 40/39 years) exhibiting chronic fatigue/dis-autonomy (≥ three symptoms for ≥ five months after last SARS-CoV-2 mRNA vaccination) not due to SARS-CoV-2 infection and/or confounding diseases/medications. Normal vaccination response encompassed decreases of 11 receptor-antibodies (by 25 - 50 %, p < 0.0001), increases in two receptor-antibodies (by 15 - 25 %, p < 0.0001) and normal IL-6. In PACVS, serological vaccination-response appeared significantly (p < 0.0001) altered, allowing discrimination from normal post-vaccination state (sensitivity = 90%, p &lt; 0.0001) by increased angiotensin II type 1 receptor antibodies (cut-off ≤ 10.7 U/ml, ROC-AUC = 0.824 ± 0.027), decreased alpha-2B adrenergic receptor antibodies (cut-off ≥ 25.2 U/ml, ROC-AUC = 0.828 ± 0.025) and increased IL-6 (cut-off ≤ 2.3 pg/ml, ROC-AUC = 0.850 ± 0.022). PACVS is thus indicated as a somatic syndrome delineated/detectable by diagnostic blood markers

G-quadruplex, a unique secondary structure in nucleic acids found throughout human genome elicited widespread interest in the field of therapeutic research. Being present in key regulatory regions of oncogenes, G-quadruplex structure regulates transcription, translation, splicing, telomere stability etc. Changes in its structure and stability lead to differential expression of oncogenes causing cancer. Thus, targeting G-Quadruplex structures with small molecules/ other biologics has shown elevated research interest. Covering previous reports, in this review we try to enlighten the facts on the structural diversity in G-quadruplex ligands aiming to provide newer insights to design first-in-class drugs for the next generation cancer treatment.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

Mungbean [Vigna radiata (L.) Wilczek] in Australia has been transformed from a niche opportunistic crop into a major summer cropping option for dryland growers in the summer-dominant rainfall regions of Queensland and New South Wales. This transformation followed stepwise genetic improvements in both grain yields and disease resistance. For example, more recent cultivars such as ‘Crystal’, ‘Satin II’ and ‘Jade-AU‘ have provided up to a 20% yield advantage over initial introductions. Improved agronomic management to enable mechanised management and cultivation in narrow (<50 cm) rows has further promised to increase yields. Nevertheless, average yields achieved by growers for their mungbean crops remain less than 1 t/ha, and are much more variable than other broad acre crops. Further increases in yield and crop resilience in mungbean are vital. In this review, opportunities to improve mungbean have been analysed at four key levels including phenology, leaf area development, dry matter accumulation and its partitioning into grain yield. Improving the prediction of phenology in mungbean may provide further scope for genetic improvements that better match crop duration to the characteristics of target environments. There is also scope to improve grain yields by increasing dry matter production through the development of more efficient leaf canopies. This may introduce additional production risks as dry matter production depends on the amount of available water, which varies considerably within and across growing regions in Australia. Improving crop yields by exploiting photo-thermal sensitivities to increase dry matter is likely a less risky strategy for these variable environments. Improved characterisation of growing environments using modelling approaches could also better define and identify the risks of major abiotic constraints. This would assist in optimising breeding and management strategies to increase grain yield and crop resilience in mungbean for the benefit of growers and industry.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densities and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on different set of true values. Some real data sets were employed to show the usefulness and flexibility of the model which serves as generalization to many sub-models in the field of engineering, medical, survival and reliability analysis.

This paper presents a novel 3-degrees-of-freedom (3-DOF) haptic master with rubber bands for self-resetting. The mechanical design avoids coupling between three directions mechanically by using three perpendicular axis intersecting at one point. Bevel gear transmission is adopted to increase the compactness of the overall structure. VR-based interactive system is designed and built by incorporating the proposed haptic master. The proposed haptic device can generate force feedback along 3-degree-of-freedom motion using motors and provide command signals to the avatar in the virtual environment. In order to analyze the performance of the developed device in terms of haptic feedback operation, ergonomics assessments are designed and experimentally implemented. Preliminary studies on the influencing factor including the guidance force, the reset force, the speed of the avatar and the arm the length have been conducted. The results of this paper are of great significance for the design of the haptic master and interactive system.

In this paper we give the improved and new analytical and semi-analytical expression for calcu-lating the magnetic vector potential, magnetic field, magnetic force, mutual inductance, torque, and stiffness between two inclined current-carrying arc segments in air. The expressions are ob-tained either in the analytical form over the incomplete elliptic integrals of the first and the sec-ond time or by the single numerical integration of some elliptical integrals of the first and the second kind. The validity of the presented formulas is proved from the special cases when the inclined circular loops are treated. We mention that all formulas are obtain by the integral ap-proach except the stiffness which is found by the derivative of the magnetic force.

Engineering of drug nanocarriers combining fine-tuned mucoadhesive/mucopenetrating properties is currently being investigated to ensure more efficient mucosal drug delivery. Aiming to improve the transmucosal delivery of hydrophobic drugs, we designed a novel kind nanogel produced by the self-assembly of amphiphilic chitosan graft copolymers ionotropically crosslinked with sodium tripolyphosphate. In this work, we synthesized for the first time chitosan-g-poly(methyl methacrylate) nanoparticles thiolated by the conjugation of N-acetyl cysteine. First, we confirmed that both non-crosslinked and crosslinked nanoparticles in the 0.05-0.1% w/v concentration range display very good cell compatibility in two cell lines that are relevant to oral delivery, Caco2 cells that mimic the intestinal epithelium and HT29-MTX cells that produce mucin. Then, we evaluated the effect of crosslinking, nanoparticle concentration and thiolation on the permeability in vitro utilizing monolayers of (i) Caco2 and (ii) Caco2:HT29-MTX cells (9:1 cell number ratio). Results confirmed that the ability of the nanoparticles to cross Caco2 monolayer was affected by the crosslinking. In addition, thiolated nanoparticles interact more strongly with mucin, resulting in a decrease of the apparent permeability coefficient (Papp) compared to the pristine nanoparticles. Moreover, for all the nanoparticles, higher concentration resulted in lower Papp suggesting indicating that the transport pathways could undergo saturation.

Blood Concentrates (BCs) are autologous non-transfusional therapeutical preparations with biological properties applied in tissue regeneration. These BCs differ in the preparation method, in fibrin network architecture, growth factors release as well as in platelet/cell content. Methodological changes result in distinct matrices that can compromise their clinical effectiveness. The present study evaluated the influence of different g-forces and types of tubes in the release of vascular endothelial growth factor (VEGF) from platelet-rich fibrin (PRF) as a function of time. The PRF-like samples were obtained with three g-forces (200, 400, and 800 x g) for 10 minutes in pure glass tubes or in polystyrene-clot activator tubes. Scanning and Transmission electron microscopy was used to morphometric analyzes of PRF’s specimens and flow cytometry was used to quantify VEGF slow release until 7 days. Our results showed that platelets were intact and adhered to the fibrin network, emitting pseudopods and in degranulation. The fibrin network was rough and twisted with exosomic granulations impregnated on its surface. An increase in the concentration of VEGF in the PRF supernatant was observed until 7 days for all g forces (200, 400 or 800 x g), with the highest concentrations observed with 200 x g, in both tubes, glass or plastic. Morphological analyzes showed a reduction in the diameter of the PRF fibers after 7 days. Our results showed that g-force interferes with the shape of the fibrin network in the PRF, as well as affect the release of VEGF stored into platelets. This finding may be useful in applying PRF to skin lesions, in which the rapid release of growth factors can favor the tissue repair process. Our observations point to a greater clarification on the methodological variations related to obtaining PRF matrices, as they can generate products with different characteristics and degrees of effectiveness in specific applications.

This paper aims to study the surface homogenization and integrity of Ti-6Al-4V alloy by longitudinal-torsional coupled ultrasonic vibration assisted ball-end milling. A method of continuous processing between the flat surface and freeform surface connection is proposed by using ultrasonic vibration assisted ball-end precision milling, during this process, it is not necessary to exchange the cutting tool. The way has been explored for changing the homogenization of surface on Ti-6Al-4V by ultrasonic vibration-assisted milling (UVAM). Cutting experiments employing three parameters, cutting speed, feed rate and depth of cut and two types of machining forms using ball-end milling with UVAM and conventional milling (CM) respectively. The high frequency cutting force, finished surface roughness, topography and residual stresses on the surface and tool wear have been measured by advanced instruments. Particularly, adopting the high frequency cutting force measurement system, it is concluded cutting force in ball-end milling decreased significantly using UVAM as against CM. Moreover, the surface roughness by UVAM with ball-end milling is much better than the CM at a high cutting speed. However, an opposite trend is observed at a low cutting speed. Especially, there is a steep decrease from Ra 0.828 μm average value at 4000 rpm to Ra 0.129 μm average value at 5000 rpm. At the same time, the homogenization of surface roughness and residual stresses decrease significantly in UVAM as compared to which in CM when taking the transversal-longitudinal ratio into consideration. Cutting experiments and measuring results are demonstrated the validity and feasibility of UVAM with ball-end milling, and this method enjoys significant advantages compared to CM process.

The paper aims in assessing risks of mandible fractures consequent to impacts or sport accidents. The role of the structural stiffness of mandible, related to disocclusion state, is evaluated through numerical simulations using the finite element method (FEM). It has been assumed that the quasi-static stress field, due to distributed forces developed during accidents, could explain the common types of mandibular fractures. Geometric model of adolescent mandible was built, upon the basis of medical imaging, in CAD software with distinction between cortical layer and inner spongy bone. The finite element model of disoccluded mandible was next created. Mandibular condyles were supposed jammed in the maxillary fossae. The total force of 700 N, simulating an impact on mandible, has been sequentially applied in three distinct areas: centrally, at canine zone and at the mandibular angle. Clinically most frequent fractures of mandible were recognized through the analysis of maximal principal stress and maximal principal strain fields. Mandibular fracture during accidents can be analyzed at satisfactory level using linear quasi-static FE models for designing protections in sport and transport. The proposed approach can be improved by introducing more realistic interactions between condylar processes and fossae.

In the manufacturing industry, cutting tool failure is a probable fault which causes damage to the cutting tools, workpiece quality and unscheduled downtime. It is very important to develop a reliable and inexpensive intelligent tool wear monitoring system for use in cutting processes. A successful monitoring system can effectively maintain machine tools, cutting tool and workpiece. In the present study, the tool condition monitoring system has been developed for Die steel (H13) milling process. Effective design of experiment and robust data acquisition system ensured the machining forces impact in the milling operation. Also, ANFIS based model has been developed based on cutting force-tool wear relationship in this research which has been implemented in the tool wear monitoring system. Prediction model shows that the developed system is accurate enough to perform an online tool wear monitoring system in the milling process.

A single photon inside a gravitational field defined by the accelerates $g$ is found to have a gravitational mass given by $m_g=(\hbar/2c^3)g$, where $\hbar$ is the reduced Planck's constant, and $c$ is the speed of light in vacuum. This force is equivalent to the curvature force introduced by Einstein's general relativity. These photons behave like the radiation emitted by a black hole. A black hole emitting such a radiation develops an entropy that is found to increase linearly with black hole mass, and inversely with the photon mass. Based on this, the entropy of a solar black hole emitting photons of mass $\sim 10^{-33}eV$ amounts to $\sim 10^{77}\,k_B$. The created photons could be seen as resulting from quantum fluctuation during an uncertainty time given by $\Delta t=c/g$. The gravitational force on the photon is that of an entropic nature, and varies inversely with the square of the entropy. The power of the massive photon radiation is found to be analogous to Larmor power of an accelerating charge.

Automobile proving ground is important for the research of vehicles which is used for the vehicle dynamics, durability testing, braking testing, etc. However, the roads in automobile proving ground will inevitably be damaged with the extension of the service life. In most previous researches, equipment similar to laser cross-section was used to detect pavement quality, the principle of which was to reflect pavement quality by detecting road surface roughness. This method ignores the elastic deformation of the roads itself when the vehicle is traveling on it and hardly compensate for the amendment. Therefore, this article presents a new method based on force sensor to reduce the impact of elastic deformation such as wheel tyre deformation, pavement deformation, and wheel rim deformation. In which, force sensors mounted on the wheels collect the three-dimensional dynamic load of the wheel.The presented method has been tested with two sets of cobblestone road load data, and the results show that The　incentives imposed by the test vehicle on the target road are 88.3%, 91.0%, and 92.05% of the incentives imposed by the test vehicle on the standard road in three dimensions, respectively. It is clear that the proposed method has strong potential effectiveness to be applied for lose detection of the special road application.

The electric field is enormously more powerful than the gravitational field. However, in our normal experience there is no electric field, the electric force is missing. How is it that when you get to larger and larger scales the gravitational field is extremely important whereas the electric field becomes less and less important [1]? This paper proposes a model to explain why gravitation dominates at a larger scale.

In this article/review, the selective interactions of several berberine and palmatine derivatives with various DNA G-quadruplex structures are reported. These derivatives were constructed starting from two natural compounds, berberine and palamatine, through specific synthetic passages following two different schemes for each of them and using several substituents. The details of these synthesis are also described. Indeed, the study of the interactions of these derivative compounds with various G-quadruplex forming sequences was carried out by means of various structural and biochemical techniques. The results show that the presence of suitable side chains are very useful to improve the interaction of the ligands with G-quadruplex structures. Thus, since G-quadruplex formation is promoted by these compounds, which have never been reported before, these may be tested as potential anticancer drugs.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

A proper transmission of the orientation between surface and underground workings, by means of vertical shafts, is an important challenge in the mining industry, especially when the mine exceeds 200 meters deep. In fact, this study is developed in a mine located to 700 meters deep. Likewise, this paper assesses the accuracy of this operation, in a case study, using the two shafts plumbing and gyroscope methods in order to compare and analyse the planimetric displacement of the base line due to different source of errors in each one. Upsides and downsides of both methods are analysed in the paper. Some disadvantages in each method have been reduced thanks to the technological progress, especially in the two shaft plumbing method. The different sources of error that affect the measures are thoroughly analysed in the study with the aim to compensate them and achieve the required precision for an underground infrastructure. Mine ventilation has been found as one of the most important sources of error in the plumbing method due to intake and return airflow. In this direction, the paper unfolds some measures to reduce the ventilation influence and details a compensation method to reduce ventilation errors.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

A critical quality attribute of therapeutic monoclonal antibodies (mAbs) is the terminal sugar molecules of the N-linked glycan attached to the fragment crystalizable (Fc) region. There exists naturally-occurring heterogeneity in the N-linked glycan structure of mAbs, and such heterogeneity has a significant influence on the clinical safety and efficacy of mAb drugs. We previously proposed a constraint-based modeling method called glycosylation flux analysis (GFA) to characterize the rates (fluxes) of intracellular glycosylation reactions and applied the method to examine the N-linked glycosylation of immunoglobulin G (IgG) in fed-batch Chinese hamster ovary (CHO) fed-batch cultivations. In this work, we significantly improved the computational efficiency of the GFA, and employed the method to analyze the glycosylation of IgG in continuous perfusion CHO cultivations. Perfusion cell cultures have several advantages over the traditional (fed-)batch operation, including higher productivity per unit volume of reactor and more consistent product quality. The GFA showed that as in the fed-batch cultivation, the dynamical changes of IgG glycan heterogeneity in the perfusion culture are mainly attributed to alterations in the galactosylation flux activity. Furthermore, a regression analysis of the galactosylation flux activity using random forest regression linked the dynamics of galactosylation activity with the cell-specific productivity of IgG and the extracellular ammonia concentration.

Increasing of the imaging rate of conventional atomic force microscopy (AFM) is almost impossible without impairing of the imaging quality, since the probe tip tends to lose contact with the sample. We propose to apply the additional nonlinear force on the upper surface of a cantilever, which will help to keep the tip and surface in contact. In practice this force can be produced by the precisely regulated airflow. Such an improvement affects the AFM system dynamics, which were evaluated using a mathematical model presented in this paper. The model defines the relationships between the additional nonlinear force, the pressure of the applied air stream and the initial air gap between the upper surface of the cantilever and the end of the air duct. It was found that the nonlinear force created by the stream of compressed air (aerodynamic force) prevents the contact loss caused by the high scanning speed or higher surface roughness, and at the same time has minimal influence on the interaction force, thus maintaining stable contact between the probe and the surface. This improvement allows to effectively increase the scanning speed by at least 10 times using a soft (spring constant of 0.2 N/m) cantilever by applying the air pressure of 40 Pa. If a stiff cantilever (spring constant of 40 N/m) is used, the potential of accuracy improvement reaches 92 times. This method is suitable for use with different types of AFM sensors and can be implemented practically without essential changes in AFM sensor design.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

Developing particles of different geometric anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Here, it is discussed that gold atoms under certain transition state amalgamated at solution surface to develop monolayer assembly around the light glow of electrons and photons, which is known in plasma, generating through flowing argon gas copper capillary, which is known in cathode. The rate of uplifting gold atoms to solution surface is controlled under the fixed optimized entrance of forced energy electron streams and photons of high forcing energy. Uplifting gold atoms dissociated on dissociation of precursor under the dissipating heat energy resulted by propagating photonic current through graphite rod immersed in the solution, which is known in anode. On the other hand, packets of nano shape energy resulted by the controlled tuned pulse protocol developing tiny particles of own shape by binding transition state atoms of compact monolayer assembly. At solution surface, adjusting atoms of monolayer tiny particle into one-dimensional arrays under the disconcerted lateral forces following by their elongation under uniformly exerted opposite poles forces. This results into convert them in a structure of smooth elements where adjacently placed electrons and those in the outer rings of elongated atoms inter-connecting side-to-side by introducing orientational-based stretching of clamped energy knots. Tiny sized particles developed their atoms of one-dimensional arrays in structure of smooth elements exert an immersing force at favorable side tips and where many such tiny particles around the light glow work as one unit for each case resulting into pack by inter-connecting at inside their common point to nucleate the shape of certain particle. Depending on the development zone of such tiny sized particles and their amount of simultaneous packing under naturally maintained orientations develop their different geometric anisotropic shaped particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles of high aspect ratio exhibiting unprecedented features are discussed.

Steroidal anti-inflammatory drugs are widely used for treatment of chronic cutaneous inflammation, such as atopic dermatitis, although it remains unknown how they modulate cutaneous mast cell functions. Murine connective tissue-type mast cells, which were sensitive to mast cell secretagogues, such as compound 48/80 and substance P, were generated by co-culture of bone marrow-derived mast cells with Swiss 3T3 fibroblasts in the presence of stem cell factor. This process was accompanied by up-regulation of a subunit of a trimeric G protein, G_i1, and several Mas-related G protein-coupled receptor (Mrgpr) subtypes. Secretagogue-induced degranulation and up-regulation of these genes were suppressed when they were cultured in the presence of a synthetic glucocorticoid, dexamethasone. The profiles of granule constituents were drastically altered by dexamethasone. Several Mrgpr subtypes were found to be expressed in the cutaneous tissues and their expression levels were decreased in response to topical application of dexamethasone. The numbers of degranulated cutaneous mast cells in response to compound 48/80 were decreased in mice treated with dexamethasone. These results suggest that mast cell-mediated IgE-independent cutaneous inflammation could be suppressed by steroidal anti-inflammatory drugs through down-regulation of G_ai1 and several Mrgpr subtypes in mast cells.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densi- ties and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on dierent set of true values. Some real data sets were employed to show the usefulness and exibility of the model which serves as generalization to many sub-models in the elds of engineering, medical, survival and reliability analysis.

Acyclic olygoheteroaryl-based compounds represent a valuable class of ligands for nucleic acid recognition. In this regard, acyclic pyridyl polyoxazoles and polyoxadiazoles were recently identified as selective G-quadruplex stabilizing compounds with high cytotoxicity and promising anticancer activity. Herein, we describe the synthesis of a new family of polyheteroaryl oxadiazole/pyridine-ligands targeting DNA G-quadruplexes. In order to perform a structure-activity analysis identifying determinants of activity and selectivity, we followed a convergent synthetic pathway to modulate the nature and number of the heterocycles (1,3-oxazole vs 1,2,4-oxadiazole and pyridine vs benzene). Each ligand was evaluated towards secondary nucleic acid structures, which have been chosen as a prototype to mimic cancer-associated G-quadruplex structures (e.g., the human telomeric sequence, c-myc and c-kit promoters). Interesting, heptapyridyl-oxadiazole compounds showed preferential binding towards the telomeric sequence (22AG) in competitive conditions vs duplex DNA. In addition, G4-FID assays suggest a different binding mode from the classical stacking on the external G-quartet. Additionally, CD titrations in the presence of the two most promising compounds for affinity, TOxAzaPy and TOxAzaPhen, display a structural transition of 22AG in K-rich buffer. This investigation suggests that the pyridyl-oxadiazole motif is a promising recognition element for G-quadruplexes, combining seven heteroaryls in a single binding unit.

G-protein-coupled receptors (GPCR) belong to a large family of molecules eliciting different responses to a variety of signaling molecules. These receptors participate in various physiologic pathways such as metabolism, growth, immune responses, inflammation, vision, taste, olfaction, neurotransmission and even and pathologic responses including chronic inflammatory and vascular diseases. Receptors contributing to the biological responses of renin-angiotensin system (RAS) are members of GPCR family. COVID-19-induced inflammatory cascade has been attributed to acute ACE2 downregulation and imbalance of proinflammatory ACE/AngII/AT1R and anti-inflammatory ACE2/angiotensin (1-7)/Mas axes in favor of the former. Some of the receptors contributing to activities of proteins in RAS including AT1R, AT2R and Mas receptors are members of GPCR family. It is notable that these receptors induce their effects both through G protein and β-arrestin pathway; the former exerts temporary and the latter more sustained effects. In addition to the imbalance of GPCR responses contributing to RAS activities, it has been suggested that SARS-CoV2 pathogenesis might be attributed to the activation of GPCRs or modulating G-proteins involved in adenosine-CFTR regulation system and epithelial Na channel function.This article includes a minireview about the physiological functions of GPCRs and their contribution to COVID-19.

The steering performance according to the steering angle control was tested by using the active steering bogie developed to reduce excessive wheels and rail wear and noise generated when the railway vehicle run in a curved section. As a result of the test of increasing the steering angle in accordance with the target steering angle in the 300m radius of curvature, the bogie is gradually aligned in the radial steering position, and when the control is carried out to 100% of the target steering angle, the bogie angles of the front and rear bogies appeared almost the same. As the steering angle increased, wheel lateral force and derailment coefficient also decreased. Therefore, the validity of the radial steering position control method applied in this paper was confirmed experimentally. This test results will be used for future research on active steering bogie commercialization.

The cyclic universe theory is a model of cosmic evolution according to which the universe undergoes endless cycles of expansion and cooling, each beginning with a big bang and ending in a big crunch. In this paper, the researcher finds a unique property of Space-time, this particular and marvelous nature of space shows us that space can shrink, expand, and stretch. This property of space is caused the size of the Universe changing over time: growing or shrinking. The observed accelerated expansion, which relates the stretching of Shrunk space for the new theory, is derived. This model is based on three underlying notions: First, the Big Bang was not the beginning of Space-time, but rather at the very beginning fraction of a second there was an infinite force of infinite Shrunk space in the cosmic singularity, that force gave rise to the big bang and caused the rapidly growing of space-time, and all other forms of energy are transformed into matter and radiation and a new period of expansion and cooling begins. Second, there was a previous phase leading up to it, with multiple cycles of contraction and expansion that repeat indefinitely. Third, the two principal long-range forces are the gravitational force and the repulsive force generated by shrunk space. They are the two most fundamental quantities in the universe that govern cosmic evolution. They may provide the clockwork mechanism that operates our eternal cyclic universe. The space will not continue to expand forever, no need however, for dark energy and dark matter. This model of Space-time and its unique properties enables us to describe a sequence of events from the Big Bang to the Big Crunch.

Background: The fascial system provides an environment that enables all body systems to operate in an integrated manner and is capable of modifying its tensional state in response to the stress applied to it. Recent in vitro, animal and cadaveric studies have shown that “myofascial force transfer” (MFT) has the potential to play a major role in musculoskeletal function and dysfunction.Objective: Human evidence for the existence of invivo MFT is scarce. This scoping review attempts to gather and analyse the available evidence of the in-vivo human MFT studies in order to sustain and facilitate further research and evidence based practice in this field.Methods: A search of most major databases was conducted with relevant keywords that yielded 238 articles as of August 2020. A qualitative analysis of the studies was conducted after rating it with Oxford’s Center for Evidence –based Medicine (CEBM) scale.Result: Nineteen studies ranging from randomized controlled trials to case studies covering 540 patients were included in this review. The analysed studies were highly heterogeneous and of lower methodological quality meddling with the quantitative analysis. Ten studies are confirming a ‘most likely’ existence of MFT, eight studies confirming it as ‘likely’ and one study couldn’t confirm any MFT existence in this review.Conclusion: Findings from in vivo human studies supports the animal and cadaveric studies claiming the existence of MFT which need to be corroborated by the future high quality studies. Forthcoming studies on MFT may give answers and solutions to many of the human musculoskeletal mysteries or dysfunctions.

(1) Background: The aim of the present study was to evaluate the effect of different types of warm-ups on the strength and skin temperature of Paralympic powerlifting athletes; (2) Methods: The participants were 15 male Paralympic powerlifting athletes. It was analyzed the effects of three different types of warm-up (without warm-up (WW), traditional warm-up (TW), or stretching warm-up (SW)) on static and dynamic strength tests as well as in the skin temperature, which was monitored by thermal imaging; (3) Results: show no differences in the dynamic and static indicators of the force in relation to the different types of warm-up. No significant differences were found in relation to the Peak Torque (p = 0.055, F=4.560, η2p= 0.246 medium effect), and 1-Repetition Maximum (p = 0.139, F=3.191, η2p = 0.186, medium effect) between the different types of warm-up. In the thermographic analysis, there was a significant difference only in the Pectoral muscle clavicular portion between the TW (33.04 ± 0.71ºC) and the WW (32.51 ± 0.74ºC) (p = 0.038). The TW method also presented slightly higher values than the SW and WW in the Pectoral Muscles Sternal portion and in the Deltoid anterior portion, but with p-value &gt; 0.05; (4) Conclusions: that the types of warm-up studied do not seem to interfere with the performance of Paralympic Powerlifting athletes. However, the thermal images showed that traditional warm-up best meets the objectives expected for this preparation phase.

Objective: To evaluate the effects of left intraparietal sulcus (IPS) inhibition by repetitive transcranial magnetic stimulation (rTMS) on grip force modulation (GFM) for both hands during a unimanual task. Methods: GFM induced by manual action-verb listening was evaluated for each hand in a unimanual task, and the motor-evoked potentials (MEP) were recorded for both left and right hemispheres prior to and following the left IPS inhibition. Left IPS inhibition was obtained by rTMS (5 min of 1.0 Hz, 60% of maximal stimulator output) of the international 10–20 system P3 point. Seven healthy right-handed subjects were evaluated. Results: One-way repeated measures ANOVA found that MEP amplitude and duration increased following IPS inhibition in the left hemisphere and did not change in the right hemisphere. Language-induced modulation did not change in the left hemisphere, while it was significantly attenuated in the right hemisphere. Since IPS inhibition increased the left primary motor cortex (M1) excitability, the maintenance of language-induced modulation intensity suggests it was also attenuated. Conclusion: Left IPS inhibition increased left M1 excitability without changing right M1 excitability, while attenuating the language-induced GFM for both the left and right hands.

For bounded unit interval, we propose a new Kumaraswamy generalized (G) family of distributions from a new generator which could be an alternate to the Kumaraswamy-G family proposed earlier by Cordeiro and de-Castro in 2011. This new generator can also be used to develop alternate G-classes such as beta-G, McDonald-G, Topp-Leone-G, Marshall-Olkin-G and Transmuted-G for bounded unit interval. Some mathematical properties of this new family are obtained and maximum likelihood method is used for estimating the family parameters. We investigate the properties of one special model called a new Kumaraswamy-Weibull (NKwW) distribution. Parameter estimation is dealt and maximum likelihood estimators are assessed through simulation study. Two real life data sets are analyzed to illustrate the importance and flexibility of this distribution. In fact, this model outperforms some generalized Weibull models such as the Kumaraswamy-Weibull, McDonald-Weibull, beta-Weibull, exponentiated-generalized Weibull, gamma-Weibull, odd log-logistic-Weibull, Marshall-Olkin-Weibull, transmuted-Weibull, exponentiated-Weibull and Weibull distributions when applied to these data sets. The bivariate extension of the family is proposed and the estimation of parameters is given. The usefulness of the bivariate NKwW model is illustrated empirically by means of a real-life data set.

Graphite carbon nitride (g-C3N4) supported PtNi alloy nanoparticles (NPs) were fabricated via a facile and simple impregnation and chemical reduction method and explored their catalytic performance towards hydrogen evolution from ammonia borane (AB). Interestingly, the resultant Pt_0.5Ni₀.5/g-C₃N₄ catalyst affords superior performance, including 100% conversion, 100% H₂ selectivity, yielding the extraordinary initial total turnover frequency (TOF) of 250.8 mol_H2 min^-1 (mol_Pt)^-1 for hydrogen evolution from AB at 10 °C, a relatively low activation energy of 38.09 kJ mol⁻¹, and a remarkable reusability (at least 10 times), which surpass most of the noble metal heterogeneous catalysts. This notably improved activity is attributed to the charge interaction between PtNi NPs and g-C₃N₄ support. Especially, the nitrogen-containing functional groups on g-C₃N₄, serving as the anchoring sites for PtNi NPs, may be beneficial for becoming a uniform distribution and decreasing the particle size for the NPs. Our work not only provides a cost-effective route for constructing high-performance catalysts towards the hydrogen evolution of AB but also prompts the utilization of g-C₃N₄ in energy fields.

A finite-type immersion or smooth map is a nice tool to classify submanifolds of Euclidean space, which comes from eigenvalue problem of immersion. The notion of generalized 1-type is a natural generalization of those of 1-type in the usual sense and pointwise 1-type. We classify ruled surfaces with generalized 1-type Gauss map as part of a plane, a circular cylinder, a cylinder over a base curve of an infinite type, a helicoid, a right cone and a conical surface of $G$-type.

Taste signaling is a complex process that is linked to obesity and its associated metabolic syndromes. The sweet taste is mediated through a heterodimeric G protein coupled receptor (GPRC) in a species-specific manner and at multi-tissue specific levels. The sweet receptor recognizes a large number of ligands with structural and functional diversities to modulate different amplitudes of downstream signaling pathway(s). The human sweet-taste receptor has been extremely difficult to study by biophysical methods due to inadequate methods for producing large homogeneous quantities of the taste-receptor protein and a lack of reliable in vitro assays to precisely measure productive ligand binding modes leading to activity upon their interactions with the receptor protein. We report a multimodal high throughput assays to monitor ligand binding, receptor stability and conformational changes to model the molecular interactions between ligand-receptor. We applied saturation transfer difference nuclear magnetic resonance spectroscopy (STD-NMR) complemented by differential scanning calorimetry (DSC), circular dichroism (CD) spectroscopy, and intrinsic fluorescence spectroscopy (IF) to characterize binding interactions. Our method using complementary NMR and biophysical analysis is advantageous to study the mechanism of ligand binding and signaling processes in other GPCRs.

Pure-compression shells have been the central topic in the form-finding of shells. This paper studies tension-compression mixed type shells by utilizing a NURBS-based isogeometric form-finding approach that analyzes Airy stress functions to expand the possible plan geometry. A complete set of smooth version graphic statics tools is provided to support the analyses. The method is validated using examples with known solutions, and a further example demonstrates the possible forms of shells that the proposed method permits. Additionally, a guideline to configure a proper set of boundary conditions is presented through the lens of asymptotic lines of the stress functions.

The 20–60-μm axon initial segment (AIS) is proximally located at the interface between the axon and cell body. AIS has characteristic molecular and structural properties regulated by the crucial protein, ankyrin-G. The AIS contains a high density of Na+ channels relative to the cell body, which allows low thresholds for initiation of action potential (AP). Molecular and physiological studies have shown that the AIS is also a key domain for the control of neuronal excitability by homeostatic mechanisms. The AIS has high plasticity in normal developmental processes and pathological activities such as injury, neurodegeneration, and neurodevelopmental disorders (NDDs). In the first half of this review, we provide an overview of the molecular, structural, and ion-channel characteristics of AIS, AIS regulation through axo-axonic synapses, and axo-glial interactions. In the second half, to understand the relationship between NDDs and AIS, we discuss the activity-dependent plasticity of AIS, the human mutation of AIS regulatory genes, and the pathophysiological role of the abnormal AIS in the NDD model animals and patients. We propose that AIS may provide a potentially valuable structural biomarker in response to abnormal network activity in vivo as well as a new treatment concept at the neural circuit level.

The present study provides molecular insight into the mechanisms underlying energy dissipation and lubrication of a smooth contact lubricated by an ionic liquid. We have performed normal and lateral force measurements with a surface forces apparatus and by colloidal probe atomic force microscopy on following model systems: 1-ethyl-3-methyl imidazolium bis-(trifluoro-methylsulfonyl)imide, in dry state and in equilibrium with ambient (humid) air; the surface was either bare mica or functionalized with a polymer brush. The velocity-dependence of the friction force reveals two different regimes of lubrication, boundary-film lubrication, with distinct characteristics for each model system, and fluid-film lubrication above a transition velocity V*. The underlying mechanisms of energy dissipation are evaluated with molecular models for stress-activated slip and flow, respectively. The stress-activated slip assumes that two boundary layers (composed of ions/water strongly adsorbed to the surface) slide pass each; the bond dynamics and the strength of the interaction at the slip plane dictate the change in friction -decreasing, increasing or remaining constant- with velocity in the boundary-film lubrication regime. Above a transition velocity V*, friction monotonically increases with velocity in the three model systems. Here, layers of ions slide past each (“flow”) under a shear stress and friction depends on a shear-activation volume that is significantly affected by confinement. The proposed friction model provides a molecular perspective of the lubrication of smooth contacts by ionic liquids and allows identifying the physical parameters that control friction.

Background: In the heart, aldosterone (Aldo) binds the mineralocorticoid receptor (MR) to exert damaging, adverse remodeling-promoting effects. We recently showed that G protein-coupled receptor (GPCR)-kinase (GRK)-5 blocks the cardiac MR by directly phosphorylating it, thereby repressing its transcriptional activity. MR antagonist (MRA) drugs block the cardiac MR reducing morbidity and mortality of advanced human heart failure. Non-steroidal MRAs, such as finerenone, may provide better cardio-protection against Aldo than classic, steroidal MRAs, like spironolactone and eplerenone. Herein, we sought to investigate potential differences between finerenone and eplerenone at engaging GRK5-dependent cardiac MR phosphorylation and subsequent blockade. Methods: We used the cardiomyocyte cell line H9c2 and neonatal rat ventricular myocytes (NRVMs). Results: GRK5 phosphorylates the MR in H9c2 cardiomyocytes in response to finerenone but not to eplerenone. Unlike eplerenone, finerenone alone potently and efficiently suppresses cardiac MR transcriptional activity, thus displaying inverse agonism. GRK5 is necessary for finerenone`s inverse agonism, since GRK5 genetic deletion renders finerenone incapable of blocking cardiac MR transcriptional activity. Eplerenone alone does not fully suppress cardiac MR basal activity regardless of GRK5 expression levels. Finally in NRVMs, GRK5 is necessary for the anti-apoptotic and anti-fibrotic effects of both finerenone and eplerenone against Aldo, as well as for the higher efficacy and potency of finerenone at blocking Aldo-induced apoptosis and fibrosis. Conclusions: Finerenone, but not eplerenone, induces GRK5-dependent cardiac MR inhibition, which underlies, at least in part, its higher potency and efficacy, compared to eplerenone, as an MRA in the heart. GRK5 acts as a co-repressor of the cardiac MR and is essential for efficient MR antagonism in the myocardium.

STRAS (Single access Transluminal Robotic Assistant for Surgeons) is a flexible robotic system based on the Anubis® platform of Karl Storz for application to intra-luminal surgical procedures. It consists of three cable-driven systems, one endoscope serving as guide and two inserted instruments. The flexible and bendable instruments have three degrees of freedom and can be teleoperated by a single user via two specially designed master interfaces. In this research, a pair of specific sensor gloves, which ergonomically fit to the master handles of the system was designed and the forces applied by one expert and one novice user during system-specific task execution in a simulator task (4-step-pick-and-drop) were compared. The results show that user expertise is not only reflected by shorter task execution times but also, more importantly, by specific differences in handgrip force profiles for specific sensor locations on anatomically relevant parts of the fingers and hand controlling the surgical instruments of the robotic master/slave system.

There is a confusion in the original design concept for the tensioning of longitudinally connected reinforcement of CRTSII slab ballastless track. In order to clarify the effect of tension value of longitudinal reinforcement on mechanical characteristics of ballastless track, a three dimensional finite element model considering the nonlinear interaction between the track slab and CA mortar of CRTSII slab ballastless track was established. The mechanical characteristics of the track structure under longitudinal tension load and temperature gradient load of the longitudinal joint were calculated. A method of applying pre-stress to post-pouring concrete was proposed according to the concept of pre-stress loss of pretensioning pre-stressed concrete, reasonable tensile force value was proposed after the crack width and the reinforcement stress of the ballastless track in the operation stage were checked and calculated according to the concrete design principle. When the tension force is greater than 300 kN, it’s harmful to the bonding between the slab and mortar layer, which is prone to interlayer damage. In order to adding pre-stress to concrete of wide joints to ensure the longitudinal stability of ballastless track and the reinforcement stress and crack width to meet the design requirements. It is suggested that the tension force value should be 230 kN, and the temperature difference between reinforcement and concrete should be 30 °C before the initial curdle of wide joint concrete.

Protein is the proteios building block of life. Evolutionarily, its sequence is not as conserved as its structure, making it more reasonable for protein structure, instead of protein sequence, to be the descriptor of protein function. Yet, in the National Center for Biotechnology Information (NCBI) database, the number of experimentally identified protein sequences is in great excess of that of experimentally determined protein structures inside the almost-half-a-century old Protein Data Bank (PDB). For instance, GPR151 is an proton-sensing G-protein coupled receptor (GPCR) originally identified as homologous to galanin receptors. As of March 19, 2020, GPR151’s structure has not been experimentally determined and deposited in PDB yet. Thus, an ab initio modelling approach was employed here to build a three-dimensional structure of GPR151. Overall, the ab initio GPR151 model presented herein constitutes the first structural hypothesis of GPR151 to be experimentally tested in future with previously published, currently ongoing and future GPR151 studies.

Despite a large amount of data on the association of folate metabolism disturbances with different aspects of schizophrenia, the role of the MTHFD1 1958 G>A polymorphism in this disorder is barely studied. The aim of this study was to assess the distribution of alleles and genotypes frequencies of MTHFD1 1958 G>A in patients with schizophrenia and healthy controls and to study the association of allele/genotype carriage of this SNP with biochemical markers of one-carbon metabolism and with the severity of schizophrenia symptoms. Methods: In 57 patients with schizophrenia and 37 healthy volunteers the carriage of alleles/genotypes of the MTHFD1 1958 G>A and biochemical markers of folate metabolism disturbances were evaluated. Clinical symptoms of schizophrenia and the severity of extrapyramidal side effects of therapy were assessed in patients. Results: an association of the wild GG genotype with schizophrenia was shown (GG versus AG / AA: χ2 = 7.31; p = 0.007). The serum folate level in carriers of the wild genotype GG is lower (in all participants p = 0.024, in patients p = 0.10), and the level of cobalamin in this subgroup is higher (in all participants p = 0.047, in patients p = 0.091) than in carriers of other genotypes. Patients carrying the G allele had less severe negative symptoms (p = 0.0041) and extrapyramidal side effects of antipsychotics (p = 0.054), than patients with AA genotype. The age of psychosis manifestation is the later, the more wild alleles G are present in the genotype (p = 0.00195).

Gut microbiota and its metabolites like short chain fatty acids (SCFAs) are linked with pathology of Alzheimer’s disease (AD)- a debilitating public health problem in older adults. However, strategies to beneficially modulate gut microbiota and its sensing signaling pathways remain largely unknown. Here, we screened, validated and established the agonists of free fatty acid receptor 2 (FFAR2) signaling, which senses beneficial signals from SCFAs produced by microbiota in the gut. We demonstrated that inhibition of FFAR2 signaling increases amyloid-beta (Aβ) stimulated neuronal toxicity. Thus, we screened FFAR2 agonists, using in-silico library of more than 144,000 natural compounds, and 15 compounds were selected based on binding with FFAR2 agonist sites. Further, cell culture toxicity and FFAR2 stimulatory experiments demonstrated that Fenchol (a natural compound commonly present in basil) was potent FFAR2 agonist in neuronal cells. Interestingly, we also demonstrated that Fenchol protects Aβ-stimulated neurodegeneration in FFAR2 dependent manner. In addition, Fenchol reduced AD like phenotypes such as Aβ-accumulation and, learning and memory behaviors in Caenorhabditis (C.) elegans. Fenchol increased Aβ-clearance by increasing proteasome/lysosome activity and reduced senescence in neuronal cells. These results demonstrated that the inhibition of FFAR2 signaling promotes Aβ-induced neurodegeneration, while activating it by Fenchol as a natural agonist reverse it by promoting Aβ-clearance and reducing cellular senescence; thus stimulation of FFAR2 signaling can be a therapeutic approach to prevent/ treat AD.

The design of torsional springs for Series Elastic Actuators (SEAs) is challenging, especially when it comes to balancing good stiffness characteristics and efficient torque robustness. This study focuses on the design of a lightweight, low-cost, and compact torsional spring for use in rotary series elastic actuator (ES-RSEA) of lumbar support exoskeleton. The exoskeleton is used as an assistive device to prevent lower back injuries. The torsion spring was designed following design for manufacturability (DFM) principles, focusing on minimal space and weight. The design process consisted of determining the potential topology and optimizing the selected topology parameters through finite element method (FEM) to reduce equivalent stress. The prototype was made using a waterjet cutting process with low-cost material (AISI-4140-alloy) and tested using a custom-made test rig. The results showed that the torsion spring had a linear torque-displacement relationship with 99% linearity, and the deviation between FEM simulation and experimental measurements was less than 2%. The torsion spring has a maximum torque capacity of 45.7 Nm and a stiffness of 440 Nm/rad. The proposed torsion spring is a promising option for lumbar support exoskeletons and similar applications requiring high stiffness, low weight-to-torque ratio, and cost-effectiveness.

Objectives The aim of this study was to measure the magnitude of forces in the joints of the lower limb whilst running barefoot and compare them to the forces generated whilst wearing running shoes with a thick midsole.MethodsTwenty-three volunteers who utilised running as their main sport or a training aid ran as training aid were included in this study. Each volunteer would run down a fourteen-meter-long corridor both barefoot and with running shoes. Forces for joints of the lower limb were collected using a Vicon motion analysis system and force plates. The joint forces for the ankles, knees and hips were taken as the largest joint force experienced during the stance phase and then averaged over five running trials.ResultsThere was significant reduction in the joint forces for the ankles, knees, and hips when barefoot running compared to the shod condition.ConclusionBarefoot running could be utilised to prevent both acute and degenerative injuries of the lower limb.

The Landau damping effect was observed in collisionless plasma, as a microscopic resonant mechanism between electromagnetic radiation and the collective modes. In this paper we demonstrate the occurrence of the Landau damping at macroscopic scale in the interaction between water waves and anharmonic lattice of magnetic buoys. By coupling the Navier-Stokes equations for incompressible fluid with the nonlinear dynamics of an anharmonic magnetic lattice we obtain a resonant transfer of momentum and energy between the two systems. The velocity of the flow is obtained in the Stokes approximation with Basset type of drag force. The dynamics of the buoys is calculated in the surfactant approximation for a specific frequency, then we use Fourier analysis to obtain the general time variable interaction. After involving an integral Dirichlet transform we obtain the time dependent expression of the drag force, the interaction waves-lattice with a new term in the form of a Caputo fractional derivative. We compare the results of the model with experiments performed in a wave tank with free floating magnetic buoys under the action of small amplitude gravitational waves. This configuration can be applied in studies for the attenuation with resonant damping of rogue waves, storms or tsunamis.

The description of protein disordered states is important for understanding protein folding mechanisms and their functions. In this short review, we briefly describe a simulation approach to modeling disordered protein interactions and unfolded states of globular proteins. It is based on the CABS coarse-grained protein model that uses a Monte Carlo (MC) sampling scheme and a knowledge-based statistical force field. We review several case studies showing that description of protein disordered states resulting from CABS simulations is consistent with experimental data. The case studies comprise investigations of protein-peptide binding and protein folding processes. The CABS model has been recently made available as the simulation engine of multiscale modeling tools enabling studies of protein-peptide docking and protein flexibility. Those tools offer customization of the modeling process, driving the conformational search using distance restraints, reconstruction of selected models to all-atom resolution and studies of large protein systems in a reasonable computational time. Therefore, CABS can be combined in integrative modeling pipelines incorporating experimental data and other modeling tools of various resolution.

The mineralocorticoid hormone aldosterone regulates sodium and potassium homeostasis but also adversely modulates the maladaptive process of cardiac adverse remodeling post-myocardial infarction. Through activation of its mineralocorticoid receptor (MR), a classic steroid hormone receptor/transcription factor, aldosterone promotes inflammation and fibrosis of the heart, the vasculature, and the kidneys. This is why MR antagonists reduce morbidity and mortality of heart disease patients and are part of the mainstay pharmacotherapy of advanced human heart failure. A plethora of animal studies using cell type–specific targeting of the MR gene have established the importance of MR signaling and function in cardiac myocytes, vascular endothelial and smooth muscle cells, renal cells, and macrophages. In terms of its signaling properties, the MR is distinct from nuclear receptors in that it has, in reality, two physiological hormonal agonists: not only aldosterone but also cortisol. In fact, in several tissues, including in the myocardium, cortisol is the primary hormone activating the MR. There is a considerable amount of evidence indicating that the effects of the MR in each tissue expressing it depend on tissue- and ligand-specific engagement of molecular co-regulators that either activate or suppress its transcriptional activity. Identification of these co-regulators for every ligand that interacts with the MR in the heart (and in other tissues) is of utmost importance therapeutically, since it can not only help elucidate fully the pathophysiological ramifications of the cardiac MR`s actions but also help design and develop novel better MR antagonist drugs for heart disease therapy. Among the various proteins the MR interacts with are molecules involved in cardiac G protein-coupled receptor (GPCR) signaling. This results in a significant amount of crosstalk between GPCRs and the MR, which can affect the latter`s activity dramatically in the heart and in other cardiovascular tissues. This review summarizes the current experimental evidence for this GPCR-MR crosstalk in the heart and discusses its pathophysiological implications for cardiac adverse remodeling as well as for heart disease therapy. Novel findings revealing non-conventional roles of GPCR signaling molecules, specifically of GPCR-kinase (GRK)-5, in cardiac MR regulation are also highlighted.

Purposely slow velocity resistance exercise (i.e., 10 s concentric and eccentric phases) is a popular training method, but limits the loads that can be lifted (e.g., <50% 1 RM). This study compared the biomechanical properties of purposely slow velocity (SLOW) and traditional resistance exercise (TRAD) that uses maximal lifting velocities. Healthy resistance-trained men (n=5) performed two testing sessions (barbell squat and bench press) in random-order; a SLOW session (1 set x 10 repetitions at 28% 1 RM, 10 s concentric & eccentric), and a TRAD session (3 x 10 at 70% 1 RM, controlled eccentric and maximal concentric). A force plate and linear position transducer were used to collect kinetic and kinematic data for every repetition of both protocols (α = 0.05). For both exercises, both concentric and eccentric mean force (N) and power (W) for each repetition was greater for TRAD. When the entire training session (squat + bench press) was examined, SLOW exhibited greater time under tension, while TRAD produced greater work (J) and impulse (N·s). Contrary to suggestions in both the lay and scientific literature, purposely slow resistance exercise produced less force, power, and work than traditional velocity resistance exercise.

Biosensors and wearable sensor systems with transmitting capabilities are currently developed and used for the monitoring of health data, exercise activities, and other performance data. Unlike conventional approaches, these devices enable convenient, continuous, and unobtrusive monitoring of a user’s behavioral signals in real time. Examples include signals relative to hand an finger movement/pressure control reflected by individual grip force data. As will be shown here, these directly translate into task, skill and hand-specific (dominant versus non-dominant hand) grip force profiles for different measurement loci in the fingers and palm of the hand. On the basis of thousands of sensor data from multiple sensor locations, individual grip force profiles of an task expert, a trained user and a highly proficient user (expert) performing an image-guided and robot-assisted precision task with the dominant or the non-dominant hand are analyzed in several steps following Tukey’s “detective work” approach. Correlation analyses (Person’s Product Moment) reveal skill-specific differences in individual grip force profiles across multiple sources of variation, functionally mapped to the somatosensory brain networks which ensure grip force control and its evolution with control expertise. Implications for the real-time monitoring of individual grip force profiles and their evolution with training in complex task-user systems are brought forward.

This study assesses the impact of globalization on female participation in the labor force (FPLF). The increased globalization in the last several decades has created various economic opportunities for enterprises and individuals worldwide at an unprecedented rate. As a result, it has helped improve the quality of life for many men and women. In this process, the issue of women’s economic participation has been a critical topic for discussion worldwide. In that context, the objective of the paper is to determine if FPLF is influenced by a country’s participation in foreign markets through foreign direct investment (FDI) – a proxy for globalization. The paper uses a panel dataset obtained from the World Bank’s World Development Indicators database for 99 countries from 2001 to 2018. We then use system Generalized Method of Moments (system GMM) to estimate a dynamic panel model with appropriate specification tests. The results show that the positive effects of FDI on FPLF are more robust for low- and middle-income countries than high-income countries. We also find that results may be sensitive to outlier observations. Our results explain the seemingly inconclusive results within existing literatures and suggest that low- and middle-income countries should particularly focus on sectors that generate FDI as they stand to yield the greatest benefits with regards to female economic empowerment.

In this tutorial review, we compare and contrast the chemical mechanisms of electrophile/oxidant sensing, and the molecular mechanisms of signal propagation. We critically analyze biological systems in which these different pathways are believed to be manifest and what the data really mean. Finally, we discuss applications of this knowledge to disease treatment and drug development.

It is desirable to upgrade previous evolutionary theories, which have remained incomplete and controversial for decades. Here we employ the concept of carbon-based entities (CBEs), which include methane, amino acids, proteins, organisms, and other entities containing relatively many carbon atoms. We deduce the driving force, mechanisms, steps, modes, tempos of CBE evolution, through integration of biology, physics, and chemistry using logics for complex issues. We hence establish the Carbon-Based Evolutionary Theory (CBET). The CBET suggests that evolution is the increase in hierarchy, diversity, fitness of CBEs under natural selection and driven by thermodynamics due to the chemical effect of the thermodynamic features of the Earth on CBEs. It provides better explanations for life origin, macroevolution events, natural selection, sympatric speciation, and evolution tempos than previous evolutionary theories. It reveals the evolutionary basis of multiple important social notions, including diversity, collaboration, altruism, obeying rules, and proper increase in freedom. It refutes some wrong notions in thermodynamics, including negative entropy (negentropy) and that biological order is equal to thermodynamic order, which have misled many people. The CBET is supported by its deduction and application. It could be a rare bridge linking laws of thermodynamics, evolution of life, and development of human society, and could have great significance in various sciences.

Coating of suitable materials having thickness of few atoms to several microns on a substrate is of great interest to the scientific community. Hard coatings develop under the significant composition of suitable-natured atoms where their force-energy behaviors when in certain transition state favour binding. In the binding mechanism of suitable atoms, electron belonging to outer ring filled state of gas-atom undertakes another clamp of energy knot belonging to outer ring unfilled state of solid-atom. Set process conditions develop the binding of different-natured atoms when processing their suitable composition in a system. Atoms of different nature develop structure in the form of hard coating by locating their ground points between the original ones. Here, gas-natured atoms increase the potential energy under decreasing levitational force of electrons, whereas, solid-natured atoms decrease the potential energy under decreasing gravitational force of electrons. In TiN coating, Ti–Ti atoms bind under the difference of expansion of their lattices, called nets of energy knots, where one atom just lands on the already landed atom. An adhered N-atom to a Ti-atom forms its position among four Ti-atoms where N-atom occupies the interstitial site of Ti-atoms. Two oppositely working force-energy behavior atoms deposit in the form of coating at substrate surface as per set conditions of the process. The rate of ejecting (or dissociating) solid-natured atoms depend on the nature of their source (target), process parameters and processing technique. In random arc-based vapor deposition system, depositing differently natured atoms at substrate surface depends on the input power. In addition to intrinsic nature of atoms, different properties and characteristics of coatings emerge as per engaged forces under their involved energy. The present study sets new trends in the field of coatings involving the diversified class of materials and their counterparts.

Recently, due to the miniaturization of electronic products, printed circuit boards (PCBs) have also become smaller. This trend has led to the need for high-precision electrical test equipment to check PCBs for disconnections and short circuits. The purpose of this study is to improve the position repeatability of the platform unit up to ±2.5 μm in a linear stage type test equipment. For this purpose, the causes of position errors of the platform unit are analyzed. The platform unit holding the PCB is driven by a single-axis linear ball screw drive system offset from its geometric center due to design constraints. The yaw rotation of the platform is found to have a dominant effect on position repeatability. To address this problem, the methods of adding balancing weights to the platform unit and adjusting the stiffness of LM Guides are proposed. This reduces the yaw rotation by moving the centers of mass and stiffness closer to the linear ball screw actuator. In the verification tests, the position repeatability was decreased to less than ±1.0 μm.

The present paper describes the development of a prosthetic hand based on the human hand anatomy. The hand phalanges are printed by using 3D printed with Polylactic Acid material. One of the main contributions is the investigation on the prosthetic hand joins; the proposed design enables to create personalized joins that allow the prosthetic hand a high level of movement by increasing the degrees of freedom of the fingers. Moreover, the driven wire tendons show a progressive grasping movement, being the friction of the tendons with the phalanges very low. Another important point is the use of force sensitive resistors for simulating the hand touch pressure. These are used for the grasping stop simulating touch pressure of the fingers. Surface Electromyogram (EMG) sensors allow the user to control the prosthetic hand grasping start. Their use may provide the prosthetic hand the possibility of classification of the hand movements. The practical results included in the paper prove the importance of the soft joins for the object manipulation and to get adapted to the object surface. Finally, the force sensitive sensors allow the prosthesis to actuate with more naturalness by adding conditions and classifications to the Electromyogram sensor.

Many studies discuss carbon-based materials because of the versatility of its element. They include different opinions for scientific problems and discuss fairly at convincing and compelling levels within the scope and application. A gas-state carbon atom converts into various states depending on its conditions of processing. The electron transfer mechanism in the gas-state carbon atom is responsible to convert it into various states, namely, graphite, nanotube, fullerene, diamond, lonsdaleite and graphene. The shape of ‘energy trajectory’ enables transferring electrons from the left- and right-sides of an atom is like a parabola. That ‘energy trajectory’ is linked to states (filled state and suitable nearby unfilled state) where force-exertion along the poles of transferring electrons is remained balance. So, the mechanism of originating different states of a gas-state carbon atom is under the involvement of energy first. This is not the case for atoms executing confined inter-state electron-dynamics as the force is involved first. Graphite-, nanotube- and fullerene-state atoms ‘partially evolve partially develop’ (form) their structures. These possess one-dimensional, two-dimensional and four-dimensional ordering of atoms, respectively. Their structural formation also comprises ‘energy curve’ having a shape-like parabola. Transferring suitable filled state electron to suitable nearby unfilled state is under a balance force exerting along the poles. The graphite structure under only attained-dynamics of atoms can also be formed but in two-dimension. Here, binding energy between graphite-state carbon atoms is for a small difference of exerting forces along their opposite poles. Structural formation in diamond, lonsdaleite and graphene atoms involve energy to gain required infinitesimal displacements of electrons through which they maintain orientationally-controlled exerting forces along dedicated poles. In this study, the growth of diamond is found to be south to east-west (ground) where atoms bound ground to south. Thus, diamond atoms merge for a tetra-electron ground to south topological structure. Lonsdaleite atoms merge for a bi-electron ground to just-south topological structure. The growth of graphene is found to be north to ground where atoms bound ground to north. Thus, graphene atoms merge for a tetra-electron ground to north topological structure. Glassy carbon exhibits layered-topological structure where, tri-layers of gas-, graphite- and lonsdaleite-state atoms successively bind in repetitive order. Nanoscale hardness is also sketched based on different force-energy behaviors of different state carbon atoms. Here, structure evolution in each carbon state atom explores its own science.

Mobile robots need an environmental perception ability in order to interact with the surrounding environment. In this paper we present the G-SLAM method, where the map is consisted of a cloud of scattered points in the continuous space and each point is accompanied by an obstacle existence probability. On the other hand the robot's pose (and trajectory) is estimated by an particle filters while the cloud of points is estimated by an adaptive recursive algorithm which is presented. Main feature of the presented method is the adaptive repositioning of the scattered points and their convergence around obstacles. In addition to our previous publications, In this paper a mathematical derivation of the method is presented and real case scenarios are discussed, presented and compared with other methods.

Background and objectives: The language-induced grip force modulation (GFM) can be used to better understand the link between the language and motor functions as an expression of the embodied language. However, the contribution of each brain hemisphere to the language-induced GFM is still unclear. Using six different action verbs as stimuli, this study evaluated the GFM of the left hand in unimanual task to characterize the left- and right-hemisphere contributions. Materials and Methods: The left-hand GFM of 20 healthy consistent right-handers subjects was evaluated using the verbs “to write”, “to hold”, “to pull”(left-lateralized central processing actions), “to draw”, “to tie”, and “to drive” (bi-hemispheric central processing actions) as linguistic stimuli. The time between the word onset and the first interval of statistical significance regarding the baseline (RT) was also measured. Results: The six verbs produced language-induced GFM. The modulation intensity was similar for the six verbs, but the RT was variable. The verbs “to draw”, “to tie”, and “to drive”, whose central processing of the described action is bihemispheric showed a longer Rt compared to the other verbs. Conclusions: The possibility that an action is performed by the left-hand does not interfere with the occurrence of GFM when this action verb is employed as linguistic stimulus. Therefore, the language-induced GFM seems mainly rely on the left hemisphere, and the engagement of the right hemisphere seems to slow down the increase in the GFM intensity.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

At the level of the 50 U.S. states, an interconnected nexus of well-being variables exists. These variables have been shown to strongly correlate with estimates of state IQ in interesting ways. But the state IQ estimates (McDaniel 2006) are now more than 16 years old, and the state well-being estimates (Pesta et al., 2010) are over 12 years old. Updated state IQ and well-being estimates are therefore needed. I thus first created new state IQ estimates by analyzing scores from both the Program for the International Assessment of Adult Competency (for adults), and the National Assessment of Educational Progress (for fourth and eighth grade children) exams. I also created new global well-being scores by analyzing state variables from the following four well-being subdomains: crime, income, health, and education. When validating the nexus, several interesting correlations existed among the variables. For example, state IQ most strongly predicted FICO credit scores, alcohol consumption (directly), income inequality, and state temperature. Interestingly, state IQ derived here also correlated .58 with state IQ estimates from over 100 years ago. Global well-being likewise correlated with many old and new variables in the nexus, including a correlation of .80 with IQ. In sum, at the level of the U.S. state, a nexus of important, strongly correlated variables exists. These variables comprise well-being, and state IQ is a central node in this network.

We consider the quantum thermodynamic origin of the gravitational force of matter by applying the spacetime entanglement entropy and the Unruh effect originating from vacuum quantum fluctuations. By analyzing both the local thermal equilibrium and quasi-static processes of a system, we may get both the magnitude and direction of Newton's gravitational force in our theoretical model. Our work shows the possibility that the elusive Unruh effect has already shown its manifestation through gravitational force.

The notion of the three-phase (line) tension remains one of the most disputable notions in the surface science. A very broad range of its values has been reported. Experts even do not agree on the sign of the line tension. The polymer-chain-like model of the three-phase (triple) line enables the rough estimation of the entropic input into the value of the line tension, estimated as Γ_en≅(k_B T)/d_m ≅〖10〗^(-11) N, where d_m is the diameter of the liquid molecule. The introducing of the polymer-chain-like model of the triple line is justified by the “water string” model of the liquid state, predicting strong orientation effects for liquid molecules located in the vicinity of hydrophobic moieties. The estimated value of the entropic input into the line tension is close to experimental findings, reported by various groups.

By generalizing the notion of pointwise 1-type Gauss map, the generalized 1-type Gauss map has been recently introduced. Without any assumption, we classified all possible ruled surfaces with generalized 1-type Gauss map in a 3-dimensional Minkowski space. In particular, null scrolls do not have the proper generalized 1-type Gauss map. In fact, it is harmonic.

Domain walls were studied for permalloy wires with different depth trenches (500 nm wide, 30 nm thick, 7.5 µm long, the depth of the trench was 0, 4, 5, 8, 10, 12 and 15nm). Permalloy (Ni80Fe20) wires were fabricated by electron beam lithography and Ar ion milling. When the depth of trench is smaller than 12 nm, the switching field (Hs) is increasing with the deeper trench. However, the depth of trench is bigger than half depth of thickness, the Hs is decreasing with the deeper trench. We believed that Hs increased as the trench depth increased was because the magnetic diploes force increased between the magnetic poles on two sides of the trench. The domains of the wires were divided by the trenches and the domain walls were pinned on the trenches these were confirmed by magnetic force microscopy images.

The manual muscle test (MMT) is a flexible diagnostic tool, which is used in many disciplines, applied in several ways. The main problem is the subjectivity of the test. The MMT in the version of a “break test” depends on the tester’s force rise and the patient’s ability to resist the applied force. As a first step, the investigation of the reproducibility of the testers’ force profiles is required for valid application. The study examined the force profiles of n=29 testers (n=9 experiences (Exp), n=8 little experienced (LitExp), n =12 beginners (Beg)). The testers performed 10 MMTs according to the test of hip flexors, but against a fixed leg to exclude the patient’s reaction. A handheld device recorded the temporal course of the applied force. The results show significant differences between Exp and Beg concerning the starting force (padj=0.029), the ratio of starting to maximum force (padj=0.005) and the normalized mean Euclidean distances between the 10 trials (padj=0.015). The slope is significantly higher in Exp vs. LitExp (p=0.006) and Beg (p=0.005). The results also indicate that experienced testers show inter-tester differences and partly even a low intra-tester reproducibility. That highlights the necessity of an objective MMT-assessment. Furthermore, an agreement on a standardized force profile is required – a suggestion is given.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

In this paper, the modification of two synthetic steps to obtain EMICORON, with respect to the usual protocol, is reported. EMICORON is a benzo[ghi]perylen-diimmide which was synthesized the first time in our laboratory in 2012 and showed to have in-vivo antitumor activities interfering with tumor growth and development by a multi-target mechanism of action. The provided modifications regarded the reaction times and the reaction conditions as well as the work-up procedures and allowed to increase the global yield of the process from 28% to about 40%. Thus, this new procedure may be more suitable in order to get larger amounts of EMICORON for further preclinical studies.

Background: Metastatic cancer is associated with an invariably fatal outcome. However, DeltaRex-G, a tumor- targeted retrovector encoding a CCNG1 inhibitor gene, has induced long term (>10 years) survival of patients with chemo-resistant metastatic pancreatic adenocarcinoma, MPNST, osteosarcoma, B-cell lymphoma, and breast carcinoma. Objective: To evaluate the level of CCNG1 expression in tumors as a potential biomarker for CCNG1 inhibitor therapy. Methods: CCNG1 RNA expression levels were measured in tumors (TCGA, N=9161), adjacent “tissues” (TCGA, N=678) and GTEx normal tissues (N=7187) across 22 organ sites. Differential expression of CCNG1 and Ki-67 in primary (N= 9161) vs metastatic (N= 393) tumors were also compared and particularly in primary (N=103) vs. metastatic (N=367) skin cancer (i.e., melanoma). Results: Enhanced CCNG1 RNA and protein expression were noted in tumors compared to normal analogous counterparts, and CCNG1 expression correlated significantly with that of Ki-67. Further, CCNG1 expression tended to be higher than that of Ki-67 in metastatic vs primary tumors, particularly in skin cancer (melanoma). Conclusions: Taken together, these data indicate that (1) CCNG1 expression is frequently enhanced in tumors when compared to their normal analogous counterparts, (2) CCNG1 and Ki-67 expressions are higher in metastatic vs primary tumors, (3) CCNG1 expression is significantly correlated with that of Ki-67, and (4) CCNG1 may be a stronger marker of metastasis than Ki-67. Phase 2 studies are planned to identify patients who are likely to respond favorably to CCNG1 inhibitor therapy by correlating treatment outcome parameters with CCNG1 expression levels in various cancer types.

n our previous paper, we showed that the so-called quantum entanglement also exists in classical mechanics. The inability to measure this classical entanglement was rationalized with the definition of a classical observer which collapses all entanglement into distinguishable states. It was shown that evidence for this primary coherence is Newton’s third law. However, in reformulating a "classical entanglement theory" we assumed the existence of Newton’s second law as an operator form where a force operator was introduced through a Hilbert space of force states. In this paper, we derive all related physical quantities and laws from basic quantum principles. We not only define a force operator but also derive the classical mechanic's laws and prove the necessity of entanglement to obtain Newton’s third law.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

The α(1,2)fucosyltransferase (Se enzyme) encoded by FUT2 is involved in the secretor status of ABH(O) blood group antigens. The sedel2 allele is one of the non-functional FUT2 (se) alleles in which 9.3 kb containing the entire coding region of FUT2 is deleted by Alu-mediated nonhomologous recombination. In addition to this allele, three SNPs of FUT2, c.375A>G, c.385A>T, and c.571C>T, appear to be prevalent in certain Oceanian populations such as Polynesians. Recently, we developed an endpoint genotyping assay to determine the sedel2 zygosity, using a FAM-labeled probe for detection of the sedel2 allele and a VIC-labeled probe for detection of FUT2. In this study, instead of the VIC probe, a HEX-labeled probe covering both c.375A>G and c.385A>T and a Cy5-labeled probe covering c.571C>T were added to the sedel2 allele assay mixture to allow simultaneous detection of these four variations by endpoint genotyping for the sedel2 zygosity and fluorescence melting curve analysis for c.375A>G, c.385A>T, and c.571C>T genotyping. The results obtained from 24 Samoan subjects with this method were identical to those obtained with previous methods. Therefore, it appears that present method can accurately determine these four variations simultaneously.

G protein-coupled receptors (GPCRs) are expressed essentially on all cells, facilitating cellular responses to external stimuli, and are involved in nearly every biological process. Several members of this family play significant roles in the regulation of adipogenesis and adipose me-tabolism. However, the expression and functional significance of a vast number of GPCRs in adipose tissue are unknown. We used a high-throughput RT-PCR panel to determine the expres-sion of the entire repertoire of non-sensory GPCRs in mouse white, and brown adipose tissue and assess changes in their expression during adipogenic differentiation of murine adipocyte cell line, 3T3-L1. In addition, the expression of GPCRs in subcutaneous adipose tissues from lean, obese, and diabetic human subjects was evaluated by re-analyzing RNA-sequencing data. We detected a total of 292 and 271 GPCRs in mouse white and brown adipose tissue, respectively. There is a significant overlap in the expression of GPCRs between the two adipose tissue depots but several GPCRs are specifically expressed in one of the two tissue types. Adipogenic differ-entiation of 3T3-L1 cells had a profound impact on the expression of several GPCRs. RNA se-quencing of subcutaneous adipose from healthy human subjects detected 255 GPCRs and obesity significantly changed the expression of several GPCRs in adipose tissue. Finally, we report sev-eral highly expressed GPCRs with no known role in adipose biology whose expression was sig-nificantly altered during adipogenic differentiation and/or in the diseased human subjects. These GPCRs could play an important role in adipose metabolism and serve as a valuable translational resource for obesity and metabolic research.

Quadruplex-interactive small molecules have a wide potential application, not only as drugs but also as sensors of quadruplexes structures. The purpose of this work is the synthesis of analogues of the bis-methylquinolinium-pyridine-2,6-dicarboxamide G4 ligand 360A, to identify relevant structure-activity relationships to apply to the design of other G4-interactive small molecules bearing bis-quinoline or bis-isoquinoline moieties. Thermal denaturation experiments revealed that non-methylated derivatives with a relative 1,4 position between the amide linker and the nitrogen of the quinoline ring are moderate G4 stabilizers, with a preference for the hybrid h-Telo G4. Insertion of a positive charge upon methylation of quinoline/isoquinoline nitrogen increases compounds capacity to selectively stabilize G4s compared to duplex DNA, with a preference for parallel structures. Among these, compounds having a relative 1,3-position between the charged methylquinolinium/isoquinolinium nitrogen and the amide linker are the best G4 stabilizers. More interestingly, these ligands showed different capacities to selectively block DNA polymer-ization in a PCR-stop assay and to induce G4 conformation switches of hybrid h-Telo G4. Mo-lecular dynamic simulations with the parallel k-RAS G4 structure showed that the relative spatial orientation of the two methylated quinoline/isoquinoline rings determines the ligands mode and strength of binding to G4s.

The mammalian/mechanistic target of rapamycin complex 1 (mTORC1) is activated by the small G-protein, RHEB-GTPase. On lysosome, RHEB activates mTORC1 by binding the domains of N-heat, M-heat, and FAT, which allosterically regulates ATP binding in the active site for further phosphorylation. The crucial role of RHEB in regulating growth and survival through mTORC1, makes it a targetable site for anti-cancer therapeutics. However, the binding kinetics of RHEB to mTORC1 is still unknown at the molecular level. Therefore, we studied the kinetics by in vitro and in-cell protein-protein interaction (PPI) assays. For this, we used the split-luciferase system (NanoBiT®) for in-cell studies, and prepared proteins for the in vitro measurements. Consequently, it was shown that RHEB binds to the whole mTOR both in the presence or absence of GTPɣS, with five-fold weaker affinity in the presence of GTPɣS. Also, RHEB bound to the truncated mTOR fragments of N-heat domain (60-167) and M-heat domain (967-1023) in a GTP independent manner. Furthermore, RHEB bound to the truncated kinase domain (2148-2300) with higher affinity also in GTP independently. In conclusion, RHEB binds two different binding sites of mTOR, which probably regulates the kinase activity of mTOR through multiple different molecular mechanisms.

This study describes all the properties of high T_c cuprates by introducing rotating holes that are created by angular momentum conservations on a 2D CuO₂ surface, and which have a different mass from that of a normal hole because of the magnetic field energy induced by the rotation. This new particle called a macroscopic Boson describes the doping dependences of pseudo-gap temperature and the transition temperature at which an anomaly metal phase appears and describes the origin of the pseudo-gap. Furthermore, this study introduces a new model to handle many-body interactions, which results in a new statistic equation. This statistic equation describing many-body interactions accurately explains why high T_c cuprates have significantly high critical temperatures. Moreover a partition function of macroscopic Bosons describes all the properties of anomaly metal phase, which sufficiently agree with experiments, using the result from our previous study [1] that analytically describes the doping dependence of T_c. By introducing a macroscopic Boson and the new statistical model for many-body interactions, this study uncovered the mystery of high T_c cuprates, which have been a challenge for many researchers. An important point is that, in this study, pure analytical calculations are consistently conducted, which agree with experimental data well (i.e., they do not use numerical calculations or fitting methods but use many actual physical constants).

There is an accelerating requirement for ocean sensing where autonomous vehicles can play an essential role in assisting engineers, researchers, and scientists with environmental monitoring and collecting oceanographic data. This paper is performed to develop a rigid sail for the autonomous sailing drone. Our study aims to numerically analyze the aerodynamic characteristics of curvy twin sail and compare it with wing sail. Because racing regulations limit the sail shape, only the two-dimensional geometry was open for an optimization. Therefore, this study’s first objective was to identify the aerodynamic performance of such curvy twin sails. Simultaneously, a secondary objective was to estimate the effect of the sail’s spacing and shapes. A viscous Navier-Stokes flow solver is used for the numerical aerodynamic analysis. The 2D aerodynamic investigation is a preliminary evaluation. The results have shown that the curvy twin sail designs have improved lift, drag, and driving force coefficient compared to the wing sails. The spacing between the port and starboard sails of curvy twin sail is an important parameter. The spacing is 0.035L, 0.07L, and 0.14L shows the lift coefficient reduction because of dramatically stall effect, while flow separation is improved with spacing is 0.21L, 0.28L, and 0.35L. Significantly, the spacing 0.28L shows the maximum high pressure at the lower area and the small low pressure area at leading edges, so the highest lift is generated.

We suppose that vacuum is filled with a kind of continuously distributed matter which may be called the $\Omega(1)$ substratum, or the electromagnetic aether. Suppose that the time scale of a macroscopic observer is very large compares to the the Maxwelllian relaxation time of the $\Omega(1)$ substratum. Thus, the macroscopic observer concludes that the $\Omega(1)$ substratum behaves like a Newtonian-fluid. Inspired by H. A. Lorentz, we speculate that electric charges may be extremely small hard spherical sources or spherical sinks with finite radii. Based on the spherical source and spherical sink model of electric charges, we derive Coulomb's law of interactions between static electric charges in vacuum. Further, we derive a reduced form of the Lorentz's force law for static electric charges in vacuum.

Apolipoprotein B mRNA-editing enzyme catalytic polypeptide-like (APOBEC) proteins are a diverse and evolutionarily conserved family of cytidine deaminases that provide a variety of functions from tissue-specific gene expression and immunoglobulin diversity to control of viruses and retrotransposons. APOBEC family expansion has been documented among mammalian species, suggesting a powerful selection for their activity. Enzymes with a duplicated zinc-binding domain often have catalytically active and inactive domains, yet both have antiviral function. Although APOBEC antiviral function was discovered through hypermutation of HIV-1 genomes lacking an active Vif protein, much evidence indicates that APOBECs also inhibit virus replication through mechanisms other than mutagenesis. Multiple steps of the viral replication cycle may be affected, although nucleic acid replication is a primary target. Packaging of APOBECs into virions was first noted with HIV-1, yet is not a prerequisite for viral inhibition. APOBEC antagonism may occur in viral producer and recipient cells. Signatures of APOBEC activity include G-to-A and C-to-T mutations in a particular sequence context. The importance of APOBEC activity for viral inhibition is reflected in the identification of numerous viral factors, including Vif, which are dedicated to antagonism of these deaminases. Such viral antagonists often are only partially successful, leading to selection for viral variants.

This paper proposes a Case-Based Reasoning (CBR) system to contribute to reinforce the sustainable performance of an environmental management system. The CBR system aims to support the decision-making process to select environmental management actions aimed at reducing risky trends of the environmental state of a region. The CBR system takes advantage of a set of situation-solution pairs called cases, which are stored in a memory and then retrieved as candidates to solve new problems. Situations in this work are represented by a set of risky trends of the following key environmental variables: CO2 emissions, Air-Quality, Loss of Vegetation Cover, Water Availability, and Solid Waste, whose combination damage the environmental state quality of a region. Meanwhile, solutions are represented by a set of environmental management actions. Similar situations to a given current situation are retrieved from the memory of cases and then their solutions are combined, through an adaptation mechanism, until the solution of the current problem is obtained. We used risky trends derived from real data related to the environmental states of a Mexican region to test the proposed CBR system. The results obtained provided insights into the potential of CBR systems to support the decision-making process to select environmental management actions aimed at reducing risky trends of current environmental states.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.