This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in the last section we present a concerning numerical example and the respective software.

This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.

This research paper presents our investigation of the evolving trends in the field of Learning Sciences (LS) from 2005 to 2021. LS is a multidisciplinary field that integrates various scientific disciplines to study and support learning in real-world contexts (Hoadley, 2018). Our paper aims to understand how LS practices, methods, and disciplines of interest have changed over time, considering factors like the COVID-19 pandemic and the call for more equity-based research. We collected data from the International Society of Learning Sciences (ISLS) repository, which serves as one major platform that showcases LS research. We analysed the proceedings of the ISLS annual meetings and conferences, focusing on variables such as title, abstract, issue date, publisher, and collection using web scraping tools and the RStudio software for data collection and analysis. Our findings indicate several trends in LS research. In terms of methods and practices, design-based research (DBR) and participatory methods were commonly used in LS studies. However, there was a decline in the adoption of DBR in 2021, possibly due to the limitations imposed by the COVID-19 pandemic. Project-based learning, embodied interaction, and game-based learning were the most frequently used techniques among LS researchers. When examining the population of interest and domain focus in LS research. Learners were the primary focus, with a significant increase in the number of studies focusing on students over the years. However, there was also a noticeable increase in studies focusing on teachers in more recent years. In terms of subject disciplines, science and mathematics were the primary areas of focus, but there has been increasing attention to the arts and technology in recent years. Concerning equity-based research in LS, the finding revealed a significant increase in this area from 2005 to 2021, with ICLS studies tending to focus more on equity compared to CSCL studies. These findings contribute to understanding the current status and future development of the learning sciences.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

Sentence stimuli pervade psycholinguistics research. Yet limited attention has been paid to the automatic construction of sentence stimuli. Given their linguistic capabilities, this study investigated the efficacy of ChatGPT/AI tools in generating sentence stimuli. In three psycholinguistic experiments, this study examined the acceptability and validity of AI-formulated auditory sentences and written sentences in two languages: English and Arabic. Participants gave English AI-generated stimuli similar to or higher acceptability ratings than human-composed stimuli, but the opposite was observed for Arabic AI-generated stimuli. The validity of AI-developed stimuli relied on the study design, with only Experiment 2 demonstrating the target psycholinguistic effect (L1/L2 morphosyntactic prediction). These results highlight the promising role of AI as a stimuli developer which could facilitate psycholinguistic research and increase its diversity. Implications for psycholinguistic research were discussed.

An innovative superconducting mechanism was developed based on a patented discovery of room temperature superconductivity in several thorium (Th) salts or compounds. The rationale behind this discovery is through the experimental results about the unique electrical and magnetic properties of these Th salts. Accordingly, this new superconducting mechanism for these Th salts was obtained through the analyses of the compounds’ molecular configurations and the packings of their relevant crystal structures. Owing to the distinctive properties of the Th compounds in this discovery, we further established a different electron pairing scheme as opposed to the pairing of the Cooper pairs. Compared to the long distance electron pairing of the Cooper pairs, the new electron pairing in our mechanism is constructed by two closely correlated electrons that reside on the same atomic orbital of the Th cation as an electron lone pair. In this new superconducting mechanism, the Th cation is sitting on a relevant crystallographic lattice arrangement or a network of the relevant Th compounds. This network is constructed by many Th cations along certain crystallographic lattice arrangement where each Th cation contains one electron lone pair. This network allows the electron lone pairs on the Th cations to be delocalized over the network, “in pair”, and thus, reveals the electron lone pair in presence in a long distance fashion. The closely correlated electron lone pairs hop on this network and thus, construct the supercurrent over the network. This explanation about the superconductivity laid the basis for our superconducting mechanism. All these conclusions came from the previous studies about these compounds that illustrated their unusual features of a coexistence of high electrical conductivity and diamagnetism. These electrical and magnetic properties fall in line with that of superconductors but, surprisingly, these Th compounds have such properties at the ambient condition, meaning under room temperature and atmosphere pressure. We expect that this mechanism may be appropriate to be utilized to other superconducting cases and therefore, can be adapted to describe the superconducting phenomenon for other superconductors.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.

The Maastricht VI/Florence consensus recommends, as one of the measures to enhance the efficacy of Helicobacter pylori (H. pylori) infection eradication, a personalized treatment approach involving the selection of an antimicrobial agent based on the pre-determined resistance of H. pylori. To meet the need to develop test systems for personalized drug selection, we conducted a study of H. pylori molecular resistance in Moscow using a self-developed Sanger sequencing test platform. We validated our test system on 25 pure culture samples of H. pylori with known resistance. Sensitivity and specificity for detecting resistance to clarithromycin was 100%, and to levofloxacin - 93% and 92%, respectively. Then we tested our platform on 112 H. pylori -positive patients who had not previously received proton pump inhibitors (PPI) or antibacterial drugs. Mutations indicating resistance to clarithromycin were found in 27 (24%) samples, and to levofloxacin in 26 (23%) samples. Double resistance was observed in 16 (14%) samples. The most common mutations leading to clarithromycin resistance were 2143G and 2142G, to levofloxacin resistance – 261A and 271A in the gyrA gene, which account for 69% of all identified genetic determinants in levofloxacin-resistant bacteria. Thus, a personalized approach to the selection of H. pylori eradication therapy based on the detection of bacterial resistance before prescribing first-line therapy could help avoid the prescription of ineffective H. pylori eradication therapies and, overall, contribute to the control of antibiotic resistance of H. pylori.

This paper addresses the conceptual exploration of various issues that form an integral part of the ethical dimensions surrounding the use of artificial intelligence (AI) in the field of marketing. We critically review some of the main ethical challenges AI poses to humanity: privacy, data security, bias, transparency, and accountability. Therefore, we will discuss the delicate balance between exploiting the transformation potential of AI for personally designed marketing strategies and ethical imperatives to safeguard the rights of consumers to retain trust. Then, the present regulatory landscape responding to these ethical challenges will be assessed by building on effective regulation, like the GDPR, existing proposed legislative frameworks, and industry guidelines. To underscore the role of an ongoing dialogue between marketers, technologists, ethicists, and regulators for developing a responsible AI ecosystem in marketing. Further, strategic recommendations for implementing company-based ethical AI marketing practices. The further strong guidelines provide enhancement transparency to consumers and investment in research to remove biases from algorithms. It also underscores principal scopes of further research and development, focusing on the need for new-age solutions to guide the ethical quagmires that AI-led marketing throws up. We suggest that integration should be done proactively and collaboratively. Thus, if attention is paid more to ethics and multidisciplinary dialogue, only such hyperbolic promises can be realized by AI-driven marketing. There are such promises through which AI-driven marketing will meet business goals and be huge at societies' values.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

The delivery of therapeutical molecules through the skin, particularly to its deeper layers is impaired due to the stratum corneum layer, which acts as barrier to foreign substances. Thus, for the past years, scientists have focused on the development of more efficient methods to deliver molecules to skin distinct layers. Microneedles, as a new class of biomedical devices, consists on an array of microscale needles. This particular biomedical device had been drawing attention due to their ability to breach the stratum corneum, forming micro-conduits to facilitate the passage of therapeutical molecules. The microneedle device has several advantages over conventional methods, such as better medication adherence, easiness and painless self-administration. Moreover, it is possible to deliver the molecules swiftly or over time. Microneedles can vary in shape, size and composition. The design process of a microneedle device must take in account several factors, like the location delivery, the material and manufacturing process. Microneedles have been used in a large number of fields from drug and vaccine application, cosmetics, therapy, diagnosis, tissue engineering, sample extraction, cancer research, wound healing, among others.

The paradigm shift has revealed a need among industrial designers to have entrepreneurial capabilities. Being the most effective modality to exercise discipline today. The implementation of this approach requires reviewing the discursive scaffolding that the design has been using to set immovable high standards of complexity and quality, reducing the field of professional action and limiting the intervention alternatives. This article considers the dynamics and trends in people's lifestyles, explores possible strategies and specific content for the entrepreneurial training required by design.

Algorithms, indispensable to understand Artificial Intelligence (AI), are omnipresent in social media but users’ understanding of these computational processes and the way they impact their consumption of information is often limited. There is a need for Media and Information Literacy (MIL) research investigating a) how MIL can support Algorithm Literacy (AL) as a subset of competences, and with what working definition, b) what competences users need in order to evaluate algorithms critically and interact with them effectively, and c) how to design learner-centred interventions that foster increased user understanding of algorithms and better response to disinformation spread by such processes. Based on Crossover project research, this paper looks at four scenarios of use by journalists, developers and MIL experts that mirror users’ daily interactions with social media. The results suggest several steps towards integrating AL within MIL goals, while providing a concrete definition of Algorithm-literacy that is experience-based. The competences and design considerations are organised in a conceptual framework thematically derived from the experimentation. This contribution can support AI developers and MIL educators in their co-design of algorithm-literacy interventions and guide future research on AL as part of a set of nested AI literacies within MIL.

Dysregulation of the Cyclin-dependent kinase 8 (CDK8) activity has been associated to many diseases including the colorectal and breast cancer. As usual in the CDK family, the activity of CDK8 is controlled by a regulatory protein called cyclin C (CycC). But while human CDK family members are generally activated in two steps that is, the binding of the cyclin to CDK and the phosphorylation of a residue in the CDK activation loop, CDK8 does not require the phosphorylation step to be active. Another peculiarity of CDK8 is its ability to be associated to CycC while adopted an inactive form. These specificities raise the question of the role of CycC in the complex CDK8-CycC, which appears to be more complex than for the other members of CDK family. Through MD simulations and binding free energy calculations, we investigated the effect of CycC on the structure and dynamics of CDK8 on the one hand, and the structural molecular basis of the protein-protein interaction between the two partners on the other hand. We found that CycC has a stabilizing effect on CDK8 and identified specific interaction hotspots within its interaction surface compared to other human CDK/Cyc pairs. Targeting these specific interaction hotspots could be a promising approach in terms of specificity, to effectively disrupt the interaction between CDK8. The simulation of the conformational transition from the inactive to the active form of CDK8 suggests that the residue Glu99 of the CycC may assume the role of the missing phosphorylation step in the activation mechanism of CDK8. In a more general view, these results point the importance of keeping the CycC in computational studies when studying the human CDK8 protein in both the active and the inactive form.

Verifying the accuracy of a 3D-printed object involves using an image processing system. This system compares images of the CAD model of the object to be printed with its 3D-printed counterparts to identify any discrepancies. It is important to note that the integrity of the accuracy measurement is heavily dependent on the image processing settings chosen. This study focuses on this issue by developing a customized image processing system. The system generates binary images of a given CAD model and its 3D-printed counterparts and then compares them pixel-by-pixel to determine the accuracy. Users can experiment with various image processing settings, such as grayscale to binary image conversion threshold, noise reduction parameters, masking parameters, and pixel-fineness adjustment parameters, to see how they affect accuracy. The study concludes that the grayscale to binary image conversion threshold has the most significant impact on accuracy and that the optimal threshold varies depending on the color of the 3D-printed object. The system can also effectively eliminate noise (filament marks) during image processing, ensuring accurate measurements. Additionally, the system can measure the accuracy of highly complex porous structures where the pores size, depth, and distribution are random. The insights gained from this study can be used to develop intelligent systems for the metrology of additive manufacturing.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

The PAX8/PPARγ rearrangement, producing the PAX8–PPARγ fusion protein (PPFP), is thought to play an essential role in the oncogenesis of thyroid follicular tumors. To identify PPFP-targeted drug candidates and establish an early standard of care for thyroid tumors, we performed ensemble docking-based compound screening. Specifically, we investigated which pocket structure should be adopted to search for a promising ligand compound for the PPFP; the position of the ligand binding pocket on the PPARγ side of the PPFP is common to that of PPARγ; however, the shape is slightly different between them due to environmental factors. We developed a method for selecting a PPFP structure with a relevant pocket and high prediction accuracy for ligand binding. This method was validated using PPARγ, whose structure and activity values are known for many compounds. Then, we performed docking calculations to PPFP for 97 drug or drug-like compounds with a thiazolidine backbone, which is one of the characteristics of ligands that bind well to PPARγ, registered in the DrugBank database. Furthermore, the binding affinities of promising ligand candidates were estimated more reliably using the molecular mechanics-Poisson–Boltzmann surface area method. Thus, we propose promising drug candidates for the PPFP with a thiazolidine backbone.

Recent advancements in artificial intelligence (AI) and deep learning have revolutionized the field of protein engineering, particularly in the area of de novo protein design. This review article explores the impact of AI-driven approaches on protein design, with a specific focus on the role of structure prediction neural networks, such as AlphaFold and RoseTTAFold. The article discusses the paradigm shift brought about by these networks, which have enabled the design of proteins with unique structures and functions that are not found in nature. The review covers various aspects of AI-driven protein design, including the use of protein language models to harness evolutionary information, the development of de novo protein design workflows utilizing deep learning, and the application of generative models like RFdiffusion and RoseTTAFold All-Atom. The article also highlights the successes and applications of AI-driven protein design across diverse domains, such as enzyme engineering, antibody design, and vaccine development. Additionally, the review identifies current challenges and future directions in the field, emphasizing the need to address limitations in modeling conformational dynamics and designing proteins for in vivo functionality. The article concludes by underscoring the potential of AI-driven protein design to transform various aspects of science and technology, while also acknowledging the importance of interdisciplinary collaboration and the development of robust pipelines for the validation and optimization of designed proteins. Overall, this comprehensive review serves as a valuable resource for researchers and practitioners interested in understanding the current state and future prospects of AI-driven protein design.

The optimal structural design is imperative to minimize material consumption and reduce the environmental impact of construction. Given the complexity in the formulation of structural design problems, the process of optimization is commonly performed using artificial intelligence (AI) global optimization, such as Genetic Algorithm (GA). However, the integration of AI-based optimization together with visual programming (VP) in building information modeling (BIM) projects warrants further investigation. This study proposes a workflow by combining structure analysis, VP, BIM, and GA to optimize trusses. The methodology encompasses several steps including: (i) generation of parametric trusses in Dynamo VP; (ii) performing the finite element modeling (FEM) using Robot Structural Analysis (RSA); (iii) retrieving and evaluating the FEM results interchangeably between Dynamo and RSA; (iv) finding the best solution using GA; and (v) importing the optimized model into Revit, enabling the user to perform simulations and engineering analysis, such as life cycle assessment (LCA) and quantity surveying. The feasibility of the proposed workflow was tested on benchmark problems and compared with open literature. The outcomes of this study offer insight into the opportunities and limitations of combining VP, GA, FEA, and BIM for structural optimization applications, particularly to enhance structural efficiency and sustainability in construction.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (<5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

Buildings consume 30% of the total energy consumption around the globe and 29% of the energy consumption in Egypt which in 2022 had a total population of 102 million, out of which 43 % live in urban areas . The operation of buildings contributes to around 30% of global CO2 emissions due to their high energy consumption (IEA, 2022a). Among the efforts made towards improving the energy efficiency of buildings are Advanced Energy Design Guides (AEDGs), building rating systems, codes, and standards. Furthermore, numerous research studies that are either literature review studies, experimental studies, or computational studies addressed the topic of energy efficiency in buildings. These are all examined in this literature review with the purpose of identifying the research gap in available research with a focus on Egypt. The identified gap is the development of a prescriptive path for the GPRS energy efficiency category based on whole building energy simulations.

One of the measures required by the European Green Deal to decarbonise the freight transport sector is the promotion of inland waterway transport (IWT), in particular intermodal transport in Europe. To facilitate intermodal transport on the Danube, we developed six new barge designs for the transport of 45' pallet-wide high-cube containers using a four-step approach. Our approach consisted of detailed desk research, followed by design and further analysis of the identified barge types, taking into account, for example, sight lines or stability. The container carrying capacity reaches up to 90 containers in three layers, which is double the capacity of existing standard barges on the Danube. Nevertheless, three-layer transport is hardly feasible in several cases, due to restrictions regarding sight lines and stability. We conclude that each loading condition must be evaluated separately to determine the best barge design option for each case. The study is limited by its geographical scope and the type of container used to develop the new barge designs. This could be a possible direction for further research on this topic: using other container types and/or extending the geographical scope.

Public housing stock, called Social Housing, in Italy developed between the 1950s and the 1980s. As of today, the first residential developments are almost nearing their end-of-life age, in need of urgent and intensive renovation. The European Commission, with the Renovation Wave, has set a goal of doubling the rate of building renovation over the next 10 years, reducing emissions, improving energy performance, and promoting decarburization. Renovation interventions, including structural, functional, energy, plant upgrading, etc., are to be preferred over integral demolition and reconstruction interventions, which have significant repercussions in terms of managerial and social discomfort. The case studies examined concern renovation interventions aimed at energy efficiency, functional adaptation of housing as well as facade restyling. The design variants analyzed were evaluated in terms of CO2e emissions, according to LCI (Life Cycle Inventory) and EPD (Environmental Product Declaration) approaches. This approach has a twofold purpose: to propose design guidelines, with low CO2e emissions, through hypotheses of variants to the case studies, and to propose, to the Economic Operators, economically advantageous bidding scenarios, in the procurement process.

Patients with a psychotic disorder frequently report oral health problems, while mental health nurses (MHNs) seem not to be fully aware of these problems and the risk factors. Therefore, this study aims to develop supportive tools for MHNs regarding oral health to increase sensitization among MHNs and to provide MHNs with knowledge to recognize (potential) oral health problems in patients with a psychotic disorder. We used a human-centered design in which the user, MHNs as well as experts by experience, were placed in the centre of the research process. Problems and needs in MHNs working with patients with a psychotic disorder were addressed. To identify key issues of problem as well as the needs in terms of resources, we started with focus groups (n = 9). We analysed the data thematically based on context of patients and MHNs in practice regarding oral health, preferred oral health tools focused on MHN, and intended outcomes of tools. A Multi Criteria Decision Matrix was developed and analysed (n = 9) to identify the most optimal and viable solution based on established criteria and issues that are prevalent in the work of MHNs. Most promising result was the development of a brochure with an awareness screener. The brochure with awareness screener was developed as a low-fidelity prototype for MHNs regarding oral health in patients with a psychotic disorder, based on the latest scientific evidence. After testing it, the feasibility was tested through semi-structured interviews (n=19). MHNs and experts by experience were satisfied with the tool and provided recommendations for adjustments to the content. Significant augmentations to the brochure include a clinical lesson and a toothbrush with toothpaste for patients. We can conclude that a brochure with an awareness screener is feasible for MHNs. Future steps aiming to further refine and optimize care processes for oral health tools in MHNs, should take refining eligibility criteria for psychiatric populations and the language level of the target group of a tool into account.

The fine chemical and pharmaceutical sectors are starting to advocate the use of flow chemistry due to reasons such as EHS, environmental, efficiency, cost saving and regulatory compliance. The use of trickle bed or fixed bed system could replace a batch autoclave typically used for hydrogenation reactions. However, there are few studies which detail the process from laboratory proof of concept through design to commercial realization. This study, using the production of 1,3-cyclohexanedione from catalytic hydrogenation of resorcinol as a case study demonstrates how the laboratory-scale recycle trickle bed can be used for catalyst screening and selection. Further, design data are generated by operation over a range of design superficial velocities and operating pressure that are used to derive a design correlation that is then used to specify a single stream plant at a level of definition consistent with a Preliminary Design for capital cost estimation. Finally, the further actions required in terms of data generation to increase the level of definition and confidence to a Sanction Grade or Final Design are discussed.

Conclusions: Our findings suggest that the NMS-E represents a valuable preoperative diagnostic tool for endometriosis, effectively correlating with the disease's severity and surgical outcomes. Incorporating the NMS-E into clinical practice could significantly enhance the management of endometriosis by addressing current diagnostic limitations and guiding surgical planning.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

Health comprises physical, mental and social dimensions whose interactions influence users’ experiences. Health experiences are within the context of environments. These contexts are definitive contributors to experiences – primarily because of the link to social dimensions as human beings - psychological and economic. Therefore, the study aims to investigate health resort users’ psycho-social and socio-economic characteristics to improve their access to quality healthcare. The objectives are identifying the socio-economic characteristics of an inclusive health resort, analysing the psycho-social characteristics of the inclusive health resort user, and analysing the effects of users’ psycho-social and socio-economic characteristics on their access to healthcare. The study employs the mixed research method (qualitative and quantitative). The researchers engaged in a pragmatic research philosophy that underscores positivist and interpretivist paradigms. The data collection instruments include survey questionnaires, an interview guide with a digital recorder, a direct participant observation schedule, field notes and photographs. The data analysis process involves the clustering and categorisation of data and examining concepts and themes. The research findings show a correlation between the users’ socio-economic status and access to quality healthcare in an inclusive health resort. The result further reveals that psycho-social and socio-economic characteristics of health resort users are quality healthcare access predictors. Therefore, the users’ social, psychological, and economic status should play a vital role in the design of an inclusive health resort by all stakeholders.

This paper concentrates on computing the efficiency of heliostat field systems. By conducting a comprehensive analysis of the mathematical model for optical efficiency, we have effectively simplified the complex three-dimensional illumination problem of heliostat fields into a two-dimensional issue. Our work primarily investigates the calculation methods for the average optical efficiency and output power of heliostat. Traditionally, calculating shadow and blocking efficiency, key factors affecting the optical performance of mirror fields, has posed a significant technical challenge. Through innovative improvements to the Monte Carlo simulation technique, this study has successfully reduced the spatial dimensionality of the problem. We employed a series of novel coordinate transformations to simulate light tracing on a two-dimensional plane, thereby efficiently calculating the efficiency of shadows and obstructions. Not only have we solved the computational challenges of shadow and obstruction efficiency, but our unique algorithm design also allows us to precisely obtain the overall average optical efficiency of the heliostat field while enhancing computational efficiency.

In this study, a simple machine learning-based quantitative structure-activity relationship (QSAR) model was developed to predict the inhibitory potency (pIC50 values) of FLT3 tyrosine kinase inhibitors, pivotal in treating Acute Myeloid Leukemia (AML). Distinctively, our model leverages an extensive and diverse dataset, 14 times larger than those employed in prior studies within this field, enabling an unparalleled scope of compound analysis. This vast dataset, combined with further exploration of molecular descriptors, enabled predictions of extraordinary precision, covering a broader spectrum of FLT3 inhibitors than was previously possible. The Random Forest Regressor (RFR) algorithm, selected for its superior predictive performance, was trained with 1080 inputs and validated through comprehensive external and internal methods. It achieved an remarkable coefficient of determination (R^2) of 0.941 and a standard deviation of 0.235 on a test set of 270 compounds, highlighting the efficacy of model in predicting FLT3 inhibitory activity. Key molecular descriptors were identified, enhancing our understanding of structural requirements for inhibitor potency. Additionally, we developed a user-friendly computational tool that enables the rapid prediction of pIC50 values. Utilizing this tool, potential FLT3 inhibitors were identified through ligand-based virtual screening. This study represents a major advancement in FLT3 inhibitor discovery by utilizing a simple QSAR-machine learning model. It enables more efficient and precise identification of potential drug candidates at an early stage, promising a faster development of targeted therapies and streamlining the ligand-based drug design process.

In this paper we introduce an ODE system to model the interaction between nature resources and human exploitation in a rich consumeristic society. In this model the rate of change of population depends on wealth per capita, and the rate of consumption has a quadratic growth with respect to population and wealth. As in our previous work \cite{BaCra_1}, we distinguish between renewable and non renewable resources, and we introduce a replenishment term for non renewable resources. We first get some information on the asymptotic behaviour of wealth and population, then we compute all the equilibria of the system and we study their stability when the parameter of exploitation of resources is small. Some numerical simulations confirm the theoretical results, and give suggestions for future research.

This study employs Geographic Information System (GIS) techniques to evaluate the walkability of Onaizah City, which serves as a representative model for a Saudi city situated in the Qassim region, north of the capital city, Riyadh. The goal is to evaluate how easily pedestrians can navigate the street network and identify areas that excel or need improvement in terms of walkability. The results offer insights for planning and development supporting sustainable initiatives. Approach; The study involves integrating GIS data, such as street layouts, land use patterns, and demographic information. By analyzing factors like integration values and choice values within the street network the study gauges’ walkability aspects. Furthermore, correlation analysis explores how spatial arrangements, influence walkability. By studying the case of a medium-sized Saudi city, which can then be applied to several Saudi cities. Cost distance analysis and cost-back correlation calculations are employed to determine pedestrian routes. Findings and Discussion; Through GIS techniques the study effectively assesses the walkability of Onaizah City by identifying three walking paths with lengths of (1401m, 1283m, and 1507m). The study reveals pedestrians' actual city distance. Weighted criteria assign 40% to heritage sites, 30% to green spaces, and 15% each to mosques/commercial sites. Preserving access to heritage sites and incorporating areas enhance walkability. Conclusion: Study enhances walkability understanding, offering data-driven planning suggestions. Urban planners prioritize pedestrian connectivity, considering GIS effectiveness and physical environment importance. Findings support walkability research and sustainable urban development.

Abstract Introduction: Poor structural quality of health facilities for tuberculosis (TB) diagnosis and treatment contributes to unfavorable health outcomes among TB patients. Improving the quality of healthcare services helps to avert TB-related morbidity. Despite these facts, the level of structural quality of health facilitieSs to deliver TB services is not in line with what the national TB and leprosy program (NTLP) recommends. Hence, the present study was conducted to assess the structural quality of health facilities to deliver quality TB services to TB patients among public health facilities in the Sidama region.Objectives: To determine the quality of the structural domain of TB services at public health facilities in the Sidama region of southern Ethiopia.Methods: An institution-based cross-sectional study was conducted from June to July 2023 among randomly selected public health facilities in the Sidama region. We included 40 randomly selected public health facilities that delivered TB services in the study area. Data was collected by experienced data collectors using facility audits, clinical observation checklists, structured questionnaires, and in-depth interviews. An Open Kit Mobile (ODK) application was used to collect data and exported to SPSS version 26. All statistical analysis was done using SPSS version 26.Results: The overall mean quality score for the structural dimension was 50.25 among the 40 health facilities audited in the study area.Conclusion: The quality of TB services regarding structural dimensions was poor in the study area. Therefore, any strategies must give careful attention to increasing the comprehensive structural dimension of quality TB services.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

End-to-end learned image compression codecs have notably emerged in recent years. These codecs have demonstrated superiority over conventional methods, showcasing remarkable flexibility and adaptability across diverse data domains while supporting new distortion losses. Despite challenges such as computational complexity, learned image compression methods inherently align with learning-based data processing and analytic pipelines due to their well-suited internal representations. The concept of Video Coding for Machines has garnered significant attention from both academic researchers and industry practitioners. This concept reflects the growing need to integrate data compression with computer vision applications. In light of these developments, we present a comprehensive survey and review of lossy image compression methods. Additionally, we provide a concise overview of two prominent international standards, MPEG Video Coding for Machines and JPEG AI. These standards are designed to bridge the gap between data compression and computer vision, catering to practical industry use cases.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

The multi-objective optimization design of hydraulic climbing mechanism (the core mechanism of gantry crane) was realized by using the method of combining central composite design (CCD), Kriging and multi-objective genetic algorithm (MOGA). Firstly, the hydraulic climbing mechanism model was established and the appropriate design variables were selected. The mass, maximum deformation and maximum equivalent stress of the hydraulic climbing mechanism was taken as the optimization objectives. Through the comparative analysis of the parameters of wedge block, anchor block, anchor plate、baffle, the parameters that have the greatest impact on the optimization objectives are selected as geometric constraints. Then, according to the results of experimental design, Kriging model was used to establish the response surface optimization model of objective function. Finally, the optimal results were obtained by using MOGA method. The experimental results show that the optimization strategy is reliable, and the mass of the optimized model is reduced by 10.28%. While meeting the actual production requirements, the lightweight design of the hydraulic climbing mechanism is realized, which saves the design cost and improves the material utilization rate.

(1) In an era where sustainable behavior is increasingly crucial, understanding the discrepancy between individuals' sustainability-oriented values and their actual behaviors, known as the inner-outer gap, is vital. This study explores the potential of the Tripartite Structure of Sustainability (TSS) framework to address this gap within the context of sustainable education. By reviewing literature from the databases APA, ERIC, and Web of Science, we systematically examined factors influencing sustainable actions. (2) Employing a qualitative content analysis approach, we analyzed 56 articles over a 15-year period, identifying 83 factors that either bridge or reinforce the inner-outer gap. These factors were categorized within the TSS framework, which segments sustainability-oriented actions into individual, social, and self-transcendent domains, alongside their activation points: stable, situational, or automated. (3) Our analysis revealed that self-focused factors often reinforce the gap, suggesting a hindrance to sustainable behavior. Conversely, self-transcendent factors consistently bridged the gap, promoting sustainability. Social factors showed variable impacts based on the ethical and sustainable context they were placed in, suggesting that the social environment's orientation significantly influences sustainable behavior. (4) The study concludes that the TSS framework offers a promising approach to advancing sustainability in education by facilitating a paradigm shift towards holistic and interconnected perspectives. This shift is critical for fostering sustainable behaviors, thereby contributing to the field of educational psychology and offering practical implications for educators aiming to nurture a sustainable future.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

Transformation formula under the action of a general linear fractional transformation for generalized Dedekind eta-function has been a subject of intensive study, Rademacher, Dieter, Meyer et al. However, the (Hecke) modular relation structure has not been recognized until the work of Goldstein-de la Torre, and streamlining the classical proofs in the modular relation will reveal the meaning hidden in those works. Our main aim is to elucidate the works of these researchers in the context of modular relations.

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

This paper explores the concept of feminist architecture and its potential to challenge gender norms and stereotypes in urban design. Women face specific challenges in urban spaces, including safety concerns, lack of accessibility, and discrimination. Feminist architecture offers a potential solution to these challenges by providing a framework that prioritizes the needs and experiences of marginalized groups, including women. The study employs a mixed-methods approach to conduct a review of relevant literature, case studies, and examples of feminist architecture from around the world to address research questions related to barriers and benefits of implementing feminist architecture in mainstream design practices. After identifying obstacles, this paper offers concrete strategies to overcome these barriers and the findings suggest that by prioritizing inclusivity, accessibility, sustainability, and democracy, feminist architecture principles offer a framework for designing urban environments that are just, equitable, and empowering for all individuals. However, despite the potential gains of incorporating feminist architecture into the design process, there are several barriers and limitations that designers may face. Therefore, to overcome these barriers and limitations, implementing feminist architecture principles require a commitment to understanding how gender operates in society, financial support, policy advocacy, and collaborative approaches among designers. By creating inclusive, gender-neutral, and supportive spaces and promoting diversity and inclusion within learning and practice, feminist architecture has the capacity to transform the built environment and make it more inclusive, equitable, and just for everyone.

A new type of artificial block is proposed by modifying the traditional block. Based on the physical model experiment, the wave reflection and run-up characteristics of the new ecological blocks under regular waves were examined, and the influence of the height of the "planting trough" border on the hydrodynamic properties was analyzed. The results indicate that the wave reflection and run-up would decrease with a decrease in the breakwater slope. As wave height increases, wave run-up increases, and the reflection coefficient falls. Wave reflection and run-up increase with an increasing wave period. The relative depth of the water has a smaller impact on the wave reflection than the wave run-up. The reflection coefficient of the new ecological blocks is consistently lower than that of the conventional and continues to decrease as the border of the "planting trough" is raised. The raised borders prevent water loss in the trough, resulting in no significant improvement in the wave run-up performance of the new blocks. The reflection coefficient and the relative run-up R/H gradually increase with the average wave breaking parameter ξ increase. The crude permeability coefficients for the new blocks, New Heights 1 and New Heights 2, are 0.53, 0.53, and 0.54, respectively.

Synanthropic flora (weeds, spontaneously developed plants) are plants that accompany humans, appearing as a result of anthropopressure as well as after its cessation. The potential of synanthropic flora in shaping green areas usually brings many measurable benefits that depend on land management in cities. The study aimed to determine the preferences and attitudes of adults towards synanthropic flora in settlement units. The article presents survey results from 447 city residents. The obtained results were statistically analyzed using the k-means clustering method to identify segments of respondents with similar attitudes and preferences toward synanthropic flora. Mann-Whitney U tests were employed to determine statistical differences in the demographic variables among the analyzed clusters of respondents. Additionally, multiple regression analysis was performed to identify the opinions and attitudes towards synanthropic flora, that may influence their greater acceptance in the vicinity of residential areas. The results obtained in multiple regression allow for the statement that the respondent’s evaluation of the level of support for the introduction of more synanthropic vegetation into urban greenery (Yw) grows with the increase of acceptance of synanthropic plants occurrence in surroundings. Respondents’ opinions on the subject of the presence of synanthropic plants were studied using such variables concerning: synanthropic vegetation found in turfgrasses has a positive impact on the visual attractiveness of a site (X1), synanthropic plant communities present themselves better than others (X2), presence of synanthropic vegetation in an estate improves the quality of life in that location (X3), introduction of synanthropic flora into estate arrangements is a positive (X4), support for the use of synanthropic flora for educational purposes - as elements of playgrounds or in the form of environmental workshops (X5). Residents’ acceptance of synanthropic flora in green areas is at a relatively high level.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Software stands as one of the most rapidly evolving technologies in the present era, characterized by its swift expansion in both scale and complexity which leads to challenges in quality assurance. Software Defect Prediction (SDP) emerges as a methodology crafted to anticipate undiscovered defects, leveraging known defect data from existing codes. This methodology serves to facilitate software quality management, thereby ensuring overall product quality. Machine Learning (ML) and Deep Learning (DL) methodologies exhibit superior accuracy and adaptability compared to traditional statistical approaches catalyzing active researches in this domain. However, it makes us hard to generalize not only because of the disparity between open-source project and commercial project but also the difference on each industrial sectors. Consequently, further research utilizing datasets sourced from diverse real-world sectors becomes imperative to bolster the applicability of these findings. In this study, we utilized embedded software for telecommunication systems of SAMSUNG ELECTRONICS, supplemented by the introduction of nine novel features to train the model, and subsequent analysis of results ensued. Experimental outcomes revealed that the F-measurement metric has been enhanced from 0.58 to 0.63 upon integration of the new features, thereby signifying a performance augmentation of 8.62%. This case study is anticipated to contribute to bolster the application of SDP methodologies within analogous industrial sectors.

Virtual Reality (VR) can be useful in efforts that aim to improve wellbeing of older members of the society. Within this context, the work presented in this paper aims to provide to elderly a user-friendly and enjoyable Virtual Reality (VR) application incorporating memory recalling and storytelling activities that can promote mental awareness, so that negative side effects related to brain inactivity are prevented. An important aspect of the proposed VR application is the presence of a virtual audience that listens to the stories presented by elderly users, and interacts with the user. In an effort to maximize the impact of the VR application, research was conducted to study whether the elderly are willing to use the VR application and whether they believe it can help to improve well-being and reduce the effects of loneliness and social isolation. The results show that elderly users are positive towards the use of such an application in everyday life, as a means of improving their overall well-being.

The positional cloning of single nucleotide polymorphisms (SNPs) of the neutrophil cytosolic factor 1 (Ncf1) gene, advocating that a low oxidative burst drives autoimmune disease, demands an understanding of the underlying molecular causes. A cellular target could be T cells, which have been shown to be regulated by reactive oxygen species (ROS). However, the pathways by which ROS mediate T cell signaling remain unclear. The adaptor molecule linker for activation of T cells (LAT) is essential for coupling T cell receptor-mediated antigen recognition to downstream responses, and it contains several cysteine residues that have previously been suggested to be involved in redox regulation. To address the possibility that ROS regulate T cell-dependent inflammation through LAT, we established a mouse strain with cysteine-to-serine mutations at positions 120 and 172 (LATSS). We found that redox regulation of LAT through C120 and C172 mediate its localization and phosphorylation. LATSS mice had reduced numbers of double-positive thymocytes and naïve peripheral T cells. Importantly, redox insensitivity of LAT enhanced T cell-dependent autoimmune inflammation in collagen-induced arthritis (CIA), a mouse model of rheumatoid arthritis (RA). This effect was reversed on an NCF1-mutated (NCF1m1j), ROS-deficient, background. Overall, our data shows that LAT is redox-regulated, acts to repress T cell activation, and is targeted by ROS induced by NCF1 in antigen-presenting cells (APCs).

IMPORTANCE: On December 10, 2021, the FDA published a Determination Letter, along with a Statistical Review and Evaluation Report, and concluded that under the non-informative prior, the local Bayesian optimal interval design (BOIN) design, in its revised form, can be designated fit-for-purpose for identifying the maximum tolerated dose of a new drug, assuming that dose-toxicity relationship is monotonically increasing. Although setting the BOIN design parameter p.tox = 1.4 * target.DLT.rate is recommended in almost all BOIN methodology articles and is the default value in the R package BOIN, it's unclear if the choice of p.tox should only depend on the target DLT rate and if certain range of p.tox could produce the same BOIN boundary table. DESIGN: In this simulation study, following parameters were varied one at a time, using R package BOIN, to explore their effects on the equivalence intervals of p.saf and p.tox: 1) target DLT rate, 2) n.earlystop, 3) cutoff.eli, 4) cohortsize, and 5) ncohort. And a simple 3+3 design was used as an example to explore equivalent sets of BOIN design parameters that can generate the same boundary table. RESULTS: When the early stopping parameter n.earlystop is relatively small or the cohortsize value is not optimized via simulation, it might be better to use p.tox < 1.4 * target.DLT.rate, or try out different cohort sizes, or increase n.earlystop, whichever is both feasible and provides better operating characteristics. This is because if the cohortsize was not optimized via simulation, even when n.earlystop = 12 and cohortsize > 3, the BOIN escalation/de-escalation rules generated using p.tox = 1.4 * target.DLT.rate could be exactly the same as those calculated using p.tox > 3 * target.DLT.rate, which might not be acceptable for some pediatric trials targeting 10% DLT rate. The traditional 3+3 design stops the dose finding process when 3 patients have been treated at the current dose level, 0 DLT has been observed, and the next higher dose has already been eliminated. If additional 3 patients were required to be treated at the current dose in the situation described above, the decision rules of this commonly used 3+3 design could be generated using BOIN design with target DLT rates ranging from 18% to 29%, p.saf ranging from 8% to 26%, and different p.tox values ranging from 39% to 99%. These BOIN parameters also need to satisfy a set of conditions. Meaning: This study demonstrates the importance of interpreting BOIN design parameter p.tox as an interval of toxicity rates that are considered too toxic, rather than one prespecified value that corresponds to the lowest toxicity probability that is deemed overly toxic. When designing a dose-finding trial using BOIN, it is important to perform simulation studies to identify equivalent sets of BOIN design parameters that can generate the same boundary table so that we can better compare the safety properties of different boundary tables.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

Developing sustainability competences is an important endeavor for education, as competence development can be complex and requires appropriate approaches. In the case of preparing future educators, this becomes even more important, because of their multiplier role. The current study presents how a project, based on living-lab methodology, helped preservice preschool teachers, attending a course on sustainability issues, develop sustainability-specific professional action competence. Students collaborated with an organization and a school and were trained to deliver to 6-year-old pupils, activities concerning the protection of sea turtles. The process included reflection, based on a given template. After the intervention, the preservice preschool teachers reflected upon their role and professional performance and discussed how they, benefited from this project. They further analyzed through a group interview, how the Living Lab methodology raised their professional confidence and self-efficacy, and helped them develop content knowledge, pedagogical content knowledge, and a sense of purpose and motivation for teaching about sustainability. Outcomes indicate that participants felt confident and efficacious to teach about sustainability, and developed their content knowledge, pedagogy content knowledge, motivation, and volition due to a strong sense of purpose and responsibility. The overall process facilitated the development of critical thinking, systemic thinking, reflection, and collaboration..

The only cases where exact distributions of estimates are known is for samples from exponential families, and then only for special functions of the parameters. So statistical inference was traditionally based on the asymptotic normality of estimates. To improve on this we need the {\it Edgeworth expansion} for the distribution of the standardized estimate. This is an expansion in $n^{-1/2}$ about the normal distribution, where $n$ is typically the sample size. The 1st few terms of this expansion were originally given for the special case of a sample mean. In earlier work we derived it for {\it any } standard estimate, hugely expanding its application. We call an estimate $\hat{w}$ of an unknown vector $w\in R^p$, a {\it standard estimate}, if $E\ \hat{w}\rightarrow w$ as $n\rightarrow \infty$, and for $r\geq 1$ the $r$th order cumulants of $\hat{w}$ have magnitude $n^{1-r}$ and can be expanded in $n^{-1}.$ Here we give another huge extension. We give the expansion of the distribution of {\it any smooth function} of $\hat{w}$, say $t(\hat{w})\in R^q,$ giving its distribution to $n^{-5/2}$. We do this by showing that $t(\hat{w})$, is a standard estimate of $t(w)$. This provides far more accurate approximations for the distribution of $t(\hat{w})$ than its asymptotic normality. %NOT USED: The building blocks of the Edgeworth expansions are the {\it cumulant coefficients } of the estimate. These cumulant coefficients are also needed for bias reduction, Bayes estimates and confidence regions. We give {\it chain rules} for the cumulant coefficients of $t(\hat{w})$ in terms of those of $\hat{w}$ and the derivatives of $t(w)$, up to those needed for 5th order Edgeworth expansions for $t(\hat{w})$ and its {\it tilted expansion}, useful for the tail of the distribution.

Abstract: More than 40 hypotheses predict associations between features of nest architecture and at least one measure of reproductive success. However, quantitative studies of reproductive consequences of nest characteristics remain scarce. In addition, most studies were conducted on model species of which nests can be easily monitored with artificial nest-boxes. Here we review the replicability of research protocols and findings in model species with many repeat studies focusing mainly on nest-size components, animal-derived nest material, or fresh greenery in blue tits (Cyanistes caeruleus), great tits (Parus major), tree swallows (Tachycineta bicolor), and starlings (Sturnus spp.). The studies looked for correlations between nest traits and aspects of breeding performance that can be easily quantified in the field, such clutch size, brood size at hatching or fledging, the % of eggs that hatch or fledge, or nestling characteristics assumed to reflect qualities associated with survival probabilities (e.g., morphometry, body condition, blood profiles). We discuss the consequences of poor replicability of research methodologies and provide explanations for why many of these studies reported poor associations between nest design and breeding success at different spatiotemporal scales. We also make suggestions for future research. Keywords: Nest design, Breeding success, Nest-box, Cavity-nesting birds, Replicability

We are currently facing a potential ‘polycrisis’, a critical inflection point that requires a whole-of-society response aimed at building collective foresight and preparedness for short-, medium-, and long-term risks. The role of higher education institutions and social stakeholders is decisive to make an impact. This paper depicts the alignment of academia, governance, and industry with the aim to challenge, inspire, and encourage universities to go beyond commodified courses and mere employability, enhance student growth and bind macro-scale measures that lead to a sustainable future. A modest teaching innovation project has served as a transforming lever, with the private sector joining in, to create a platform that reaches more than 50 000 undergraduate students and teaching staff. The resulting structure, rooted in the University’s strategic plan, has served to channel local and regional initiatives, establish effective partnerships with broad social members, raise awareness and promote actions to advance in the pursuit of Sustainable Development Goals. Chronology, materials and methodology, together with a description of the different courses, programmes and actions are provided. The paper concludes with some recommendations for future research, policy and cooperation among stakeholders. Research methodology posted on clinicaltrials.gov under ID NCT04392869, NCT05598944, and NCT05775978.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p&lt;0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p&lt;0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

Wind turbines are a solution for sustainable energy, significantly reducing carbon emissions and fostering a circular economy for more cost-effective and cleaner power generation, in line with worldwide environmental aspirations. In this context, this research aims to explore a novel Two-Stage Twisted Blade micro-Vertical Axis Wind Turbine ($\mu$-VAWT) alternative inspired by the Savonius Rotor (SR). This investigation utilizes the $\kappa-\omega$ SST turbulence model to explore the power coefficient ($C_P$) and torque coefficient ($C_T$), finding $C_P$ values ranging from 0.02 to 0.04 across the turbine by altering the free stream velocity ($V$). $C_T$ analysis further delves into four specific sections, highlighting areas of particular interest. These results are validated by examining velocity contours, pressure contours, and streamlines in four horizontal sections, demonstrating that the proposed turbine model exhibits minimal torque fluctuation. Moreover, the analysis of vertical wind streamlines illustrates very low interference with various wind turbine proposals, underscoring the turbine's efficiency and potential for integration into diverse wind energy projects.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

International students were – and continue to be – particularly vulnerable to the negative consequences of the COVID-19 pandemic. 625 international students in Israel completed an online survey assessing risk and protective factors (socio-demographics, health status, COVID-19 related experiences/concerns, financial difficulties, academic challenges/experiences, social support, and coping) for student’s depression, perceived need for help, and seeking help from the university. Approximately 15% of participants had moderately-severe or severe depression. Over half needed at least a little help, but only 19.7% had asked for help. Depression symptoms were related coping (β=-.34) and health (β=.12). Need for help was related to being a postdoc (β=-0.26) and experiencing food insecurity (β=0.20). Universities need to develop services which address international students’ unique needs during global crises.

The increasing demand for transporting people and goods, rail system is needed for enhancement. An architectural design of train station can significantly impact investment from any government. However, a proper guideline for designing the train station in tropical climate is not publicized. This review examine railway station design through an analysis of student design theses in Thailand, from 1983 to 2022. Furthermore, the building analyses on architectural design theory were done in terms of service area, form, entrance structure, roof structure, style, and design development. The analysis reveals curved and gable roofs are most frequent, followed by 3D curved roofs. HSR stations' main entrances are designed to represent local culture and save walking distance. Curved and gabled porticos provide the most extravagant main entryway, a feeling of grandeur and beauty. A public building's overlapping portico or curving gabled portico lends majesty and refinement to its façade. Architects and designers strive to make buildings more attractive and practical. Besides, university-designed stations prioritize conceptual design and functional space over cost. Finally, railway station design should prioritize transparency, connectivity, movement, and cost- and time-efficiency. Research gaps are identified, such as designing user-friendly for thermal comfort and design-for-all the railway station in tropical climate, are critical for future evaluation.

The use of new assistive technologies in general, and Socially Assistive Robots (SAR) in particular is becoming increasingly common for supporting people’s health and well-being. However, it still faces many issues regarding long-term adherence, acceptability and utility. Most of these issues are due to design processes that insufficiently take into account the needs, preferences and values of intended users. Other issues are related to the currently very limited amount of long-term evaluations, performed in real world settings, for SAR. This study presents the results of two regional projects that consider as a starting hypothesis that the assessment in controlled environments and/or with short exposures may not be enough in the design of a SAR deployed in a retirement home and the necessity of designing for and with users. Thus, the proposed methodology has focused in use cases definitions that follow a human-centred and participatory design approach. The main goals have been facilitating system acceptance and attachment by involving stakeholders in the robots design and evaluation, overcoming usage barriers and considering user’s needs integration. The implementation of the first use case deployed and the two-phase pilot test performed in the retirement home are presented. In particular, a detailed description of the interface re-design process based on improving a basic prototype with users’ feedback and recommendations is presented together with main results of a formal evaluation that has highlighted the impact of changes and improvements addressed in the first redesign loop of the system.

Endoscopy has made a significant and noteworthy contribution to the field of medical science and technology. Nevertheless, its potential remains constrained due to the limited availability of rigid or flexible endoscopes. This paper introduces a novel hydraulic actuator based on electrorheological fluid (ERF) as a pivotal advancement in bridging the existing gap within the realm of endoscopy. Following a comprehensive introduction that briefly outlines the electrorheological effect, the subsequent section is dedicated to the elucidation of the actuator’s development process. Challenges arise, particularly in terms of miniaturization and the realization of a hydraulically sealed system with integrated valve electrodes. An internal electrorheological valve system consisting of four valves that are controlled using a pulse-width modulated high voltage was suitable for position control of the antagonistic hydraulic actuators. High-precision stereolithography (SLA) printing has proven practical for manufacturing the actuator components. For functional testing, a test bench was set up in which the actuator follows a setpoint through a PI control loop. The control deviation ranged from 0.6 to 1 degree, with a response time between 6 and 8 seconds. The experiments have demonstrated that, through the use of ERF and integrated valve electrodes, a miniaturized functional actuator can be constructed.

This longitudinal study examined the development of executive function and calibration accuracy in pre-adolescents. Two hundred sixty two students(127 females) from grades 4 (n = 91), 5 (n = 89) and 6 (n = 82) took measures of executive function and performance calibration in a sport task, three times within a period of 20 months. A latent growth curve modeling analysis showed a significant relation between the rates of change of executive function and calibration. Further, the results showed a dynamic interplay in the development of executive function and calibration. There were significant inter-individual differences in the estimated population means both in executive function and calibration and in the rate of change of executive function, but not in the rate of change for calibration. The age of the participants had a positive effect only on the estimated population mean of executive function.

First, an introductory essay is carried out to build a historical, economic-productive and legal theoretical framework of the origin and formation of Secondary Technical Schools in Europe, North America and the Argentine Republic. Then a normative introduction to Technical Education is carried out at the Technical School No. 2 “Independencia” of Concordia, Entre Ríos, Argentine Republic. Its regulations and Laws that govern technical education. We continue analyzing the development of five (5) case studies generated in the E.E.T. No. 2 “Independence” of the city of Concordia, Province of Entre Ríos, Argentine Republic. Case study No. 1: Face masks for Covid-19, designed with CAD-STL software and printed in polylactic acid (PLA) with 3D printers, for protection from SARS-CoV-2 (Coronavirus) or Covid-19. Case study No. 2: TURBO: air extractor/blower for environments contaminated by COVID-19. Case study No. 3: ROBOT-T2: Educational Robot Made by Students and Teachers of the Technical School No. 2 (E.E.T. No. 2) “Independencia”, Concordia, Entre Ríos, Argentine Republic. Case study No. 4: Self-construction EcoBlock, for social housing. Case study No. 5: Relationships of all sciences with abductive thinking, creativity, design, art and the main relationships between Social Sciences (philosophy, logic, hermeneutic research methodology, etc.) with Exact and Natural Sciences (mathematics, physics, chemistry, biology, genetics), other sciences and disciplines such as engineering, medicine, etc. We obtain the conclusions of the development. Bibliography.

Aquaculture is rapidly becoming one of the pivotal sectors in the farm economy, driven by the increasing demand for high-quality animal protein at an affordable cost, especially with the escalating human population. However, the expansion of high-density fish populations also brings forth a challenge – the rapid transmission and spread of infectious disease agents among them. To combat this, vaccination is emerging as a reliable and standardized method for providing immunity against viral and bacterial outbreaks. The ideal vaccine is expected to be safe, effective, economical, and easily administered. The fish vaccination industry continually publishes new information on fish immunology and vaccinology, contributing to the improvement of vaccine formulation and efficacy. This review aims to offer insights into the current status of bacterial, viral, and parasitic diseases, discuss existing vaccinations, and address potential industry-threatening diseases like infectious edwardsiellosis, motile aeromonas septicemia, TiLV, salmon anemia, vibriosis, and white spot disease. Technological advancements have played a crucial role in enhancing our understanding of fish immunological mechanisms, leading to improved vaccine administration and the development of recombinant live attenuated, subunit, DNA, and RNA vaccines. However, challenges such as oral tolerance, vaccine degradation, and stressful environments persist, impacting vaccine efficacy. Addressing these challenges and gaining a deeper understanding of the fish immune system and host-pathogen interactions will be pivotal for future improvements, contributing to the sustainability of aquaculture and enhancing global food security.

Mental healthcare conditions in India are severely deficient, particularly concerning the living conditions of patients. Post-treatment, numerous individuals with mental illness are abandoned by their families, who may lack the willingness or financial means to care for them. These recovered patients often experience setbacks due to the absence of facilities aimed at developing the skills necessary for reintegrating into society. The lack of separate accommodations for recovered individuals forces them to reside with other patients, worsening their condition. The government is struggling to accommodate and finance the care of recovered patients, affecting those in need of treatment as hospital bed space becomes overwhelmed by the increasing number of cured individuals. Therefore, there is an urgent need for halfway homes. These facilities offer a range of services, including social, medical, psychological, and educational support, alongside housing. The term "halfway houses" reflects their position between fully independent living and highly regulated in-patient or correctional facilities. Following treatment, many patients experience abandonment by their families or encounter difficulties returning home due to memory loss. Recovered patients often live in confined spaces, lacking essential social skills. Therefore, establishing a workspace focused on teaching social and other necessary skills before reintegrating them into society would be a beneficial approach. This would provide a structured environment for individuals who have spent significant time in seclusion, assisting them in developing the skills needed to navigate societal challenges effectively. Recent reports indicate that over 2,000 cured patients are still housed in mental hospitals across the country, according to the NHRC. The NHRC has raised concerns about the situation, noting that all 46 Government Mental Healthcare Institutions in India display very poor and inhumane treatment of patients, leading to the issuance of notices. NHRC visits have revealed deplorable conditions in all 46 mental institutes across the country.

(1) Background: This paper details the development process of two assistive technology products (ATs) implemented in the PAID project, aiming to promote the social, educational, and labor inclusion of people with disabilities across 10 municipalities of Antioquia, Colombia. (2) Methods: Applying Design Thinking (DT) methodology, including stages of empathizing, defining, ideating, prototyping, and testing, alongside a demographic study where specific needs of people with disabilities (PwDs) were identified. (3) Results: As a result, the construction process of two specific cases of assistive technology products (ATs) is detailed, including finite element simulation, mechanical testing, and delivery to end-users. Additionally, workshops for assistive product fabrication conducted in select municipalities of the project are highlighted. (4) Conclusions: the information gathered guided the development of the ATs, focusing on their features on accessibility and ease of replication. The primary objective is to facilitate the participation of PwDs in educational environments, thus promoting inclusion and accessibility. This article describes the results of two of these ATs; however, it is worth noting that this process was performed for 112 ATs delivered through the duration of the project.

Distribution System Operators (DSOs) are adapting to changing energy demands and the shift toward renewable and decentralized energy. Circularity is increasingly relevant for DSOs as their distribution systems age and need replacing. Taking circular action, however, is generally regarded as challenging as the current circular economy (CE) landscape is highly fragmented and rarely touches the implementation level. A longitudinal case study at Dutch DSO Liander on the circu-larity of distribution transformers was used to understand empirical success factors for taking circular action and to generate prescriptive knowledge on the operationalization of circularity. Six design propositions for circular action were formulated that suggest to 1) initiate small-scale cir-cularity experiments, 2) involve technical and strategic experts, 3) synergize circularity with more urgent, primary goals 4) translate circular initiatives bottom-up and top-down, 5) collaborate with other DSOs, and 6) create multidisciplinary teams. At DSO Liander, selecting the right interventions depending on the changing context contributed to operationalizing circularity for distribution transformers and achieving circularity targets. The generalizable design propositions could assist other DSOs in optimizing their strategy toward circular action.

The production of biomass fly ash has been increasing every year in Europe, reaching 5.5 million tons in 2020. Biomass fly ash is not yet accepted in the standards as a substitute material for cement in mortar and concrete. In a first approach, the substitution limit of biomass fly ash is determined by comparing the mechanical strengths, fresh state properties and hardened properties of mortars produced with biomass fly ash to those of mortars produced with classical coal fly ash. Then, masonry and rendering mortars have been designed with different substitution rates of biomass fly ashes from wood combustion in thermal power plant. Although there is an overall decrease in performance, mortars made with biomass ash retain properties that make them suitable for use in masonry or rendering.

The central nervous system (CNS) is the final frontier in drug delivery because of the blood-brain barrier (BBB), which poses significant barriers to the access of most drugs to their targets. Kynurenic acid (KYNA), a tryptophan (Trp) metabolite, plays an important role in behavioral functions and abnormal KYNA levels have been observed in neuropsychiatric conditions. The current challenge lies in delivering KYNA to the CNS owing to its polar side chain. Recently, C-3 side chain modified KYNA analogs have been shown to cross the BBB; however, it is unclear whether they retain the biological functions of the parent molecule. This study examined the impact of KYNA analogs, specifically SZR-72, SZR-104, and the newly developed SZRG-21, on behavior. The analogs were administered intracerebroventricularly (i.c.v.), and their effects on the motor domain were compared with those of KYNA. Specifically, open field (OF) and rotarod (RR) tests were employed to assess motor activity and skills. SZR-104 increased horizontal exploratory activity in the OF test at a dose of 0.04 μmol/4 μL, while SZR-72 decreased vertical activity at doses of 0.04 and 0.1 μmol/4 μL. In the RR test, however, neither KYNA nor its analogs showed any significant differences in motor skills at either dose. Side chain modification affects affective motor performance and exploratory behavior, as the results show for the first time. In this study, we showed that KYNA analogs alter emotional components such as motor-associated curiosity and emotions. Consequently, drug design necessitates the development of precise strategies to traverse the BBB while paying close attention to modifications in their effects on behavior.

We propose a theoretical method for the deterministic shaping of quantum light via photon number state selective interactions. Nonclassical states of light are an essential resource for high precision optical techniques that rely on photon correlations and noise reshaping. Notable techniques include quantum enhanced interferometry, ghost imaging, and generating fault tolerant codes for continuous variable optical quantum computing. We show that a class of nonlinear-optical resonators can transform many-photon wavefunctions to produce structured states of light with nonclassical noise statistics. The devices, based on parametric down conversion, utilize the Kerr effect to tune photon number dependent frequency matching, inducing photon number selective interactions. With a high amplitude coherent pump, the number selective interaction shapes the noise of a two-mode squeezed cavity state with minimal dephasing, illustrated with simulations. We specify the requisite material properties to build the device and highlight the remaining material degrees of freedom which offer flexible material design.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

Abstract: A. baumannii exhibits resilience in harsh environments and progressively develops resistance to diverse antibacterial agents over time. This adaptability poses a significant challenge in treating an infection caused by this bacterium within healthcare settings. The presence of peptidoglycan, a crucial precursor for cell wall synthesis, contributes to this challenge. Peptidoglycan serves not only as a structural support in bacterial cells but also provides protection against adverse environmental conditions. The synthesis of the peptidoglycan layer involves a group of substrates such as N-acetylglucosamine (GlcNAc) and N-acetylmuramic acid (MurNAc), within a three-partitioned process occurring in the membrane, periplasmic space, and cytoplasm of each bacterium. Initiated in the cytoplasm and extending to the inner cell membrane, this synthesis starts with the production of nucleotide precursors. The first step involves the synthesis of UDP-GlcNAc, orchestrated by Glm (GlmS, GlmM, and GlmU) enzymes using fructose-6-phosphate. Subsequently, enzymes from the Mur family, namely MurB, MurA, MurD, MurC, MurI, MurF, and MurE, synthesize UDP-N-acetylmuramyl-pentapeptide (UDP-Mpp) from UDP-GlcNAc. Concurrently, on the cytosolic side, the production of membrane-surrounded undecaprenyl phosphate occurs, involving membrane-side proteins MraY and MurG in the biosynthesis of peptidoglycan. This review emphasizes updated information on Mur family proteins, encompassing physicochemical properties, nature of binding site, number and type of binding site residues, functional domain details, three-dimensional structural aspects, and their functions within bacterial cells. Special attention is directed towards their enzymatic role in peptidoglycan biosynthesis due to the limited availability of precursors in the market. Additionally, the review provides a comprehensive summary of existing inhibitors and ongoing efforts in identifying new targeted inhibitors, recognizing these enzymes as potential candidates for antibacterial drug design and discovery.

The spread of high-performance personal computers, frequently equipped with powerful Graphic Processing Units (GPU), raised the interest on a set of techniques able to extract models of electromagnetic phenomena (and devices) directly from available examples of the desired behavior. Such approaches are collectively referred to as Machine Learning (ML). A typical representative ML approach is the so called “Neural Network” (NN). Using such data-driven models allows evaluating the output in a much shorter time when a theoretical model is available, or allows predicting the behavior of the systems and devices when no theoretical model is available. With reference to a simple yet representative benchmark electromagnetic problem, some of the possibilities and the pitfalls of the use of NN for the interpretation of measurements (inverse problem) or to obtain the required measurements (optimal design problem) are discussed. The investigated aspects include the choice of the NN model; the generation of the dataset(s); the selection of hyperparameters (hidden layers, training paradigm). Finally, the capabilities in the handling of ill-posed problems are critically revised.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

Multi-rotor drones, a kind of unmanned equipment which is widely used in military, commercial consumption and other fields, has been developed very rapidly in recent years. However, their short flight time has hindered the expansion of their application range. This can be addressed by utilizing hydrogen fuel cells, which exhibit high energy density, strong adaptability to ambient temperature, and no pollution emissions, as the power source. Accordingly, the application of hydrogen fuel cells as the power source in multi-rotor drones is a promising technology that has attracted significant research attention. This paper summarizes the development process of hydrogen fuel cell mul-ti-rotor drones and analyzes the key obstacles that need to be addressed for the further development of hydrogen fuel cell multi-rotor drones, including structural lightweight, hydrogen storage methods, energy management strategies. Additionally, prospects for the future development of hydrogen fuel cell multi-rotor drones are presented.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

The last decade has witnessed rapid development of immersive virtual reality (IVR) and its application in various contexts. However, its application in supporting real-time virtual collaboration has been quite rare due to technical barriers and the lack of validated design principles. To address this research gap, this study designed and developed an IVR space to enable multi-user synchronous co-located collaboration. An evaluation study (N = 95) was conducted to explore its useful design considerations and the influencing factors for collaboration experience. The IVR space was enabled by the simultaneous localization and mapping (SLAM)-based inside-out tracking technique and was informed by four essential design considerations for promoting effective collaboration in IVR, namely, the role script, learning task, collaboration mechanism, and communication design. The study results revealed that students in general were satisfied with their collaboration experience in IVR, with social presence and collaboration competency as significant predictors of collective efficacy and social experience. Based on both quantitative and qualitative results, this study proposes four validated principles for designing effective IVR spaces to support synchronous co-located collaboration.

The regional recycling of plant waste from municipal green space maintenance, private households and private gardens is traditionally carried out in partially open composting plants. In addition to climate-relevant gases, dust, germs and odours are emitted. Compared to aerobic rotting the pyrolysis at higher temperatures and/or reforming offers industrial utilisation of plant based biowaste, with additional availability of energetic by-products. A high-quality plant charcoal derived from a pilot plant is used in a one-year field trial to establish a theoretical comparability with substrates from composting. The advantages and disadvantages of composting and high-quality pyrolysis is shown for comparison, to foster further investigation in advanced technologies for production of plant charcoal aiming the sequester of biogenic Carbondioxide.

The feeling of beauty is one of the positive human feelings. In architecture and design, it is associated with forms appropriate to their purpose. The usefulness of products to meet needs is also important. They are well received by users. The task of designers is to achieve perfection in their work. The rational design and use of artificial living environments are expressions of concern for natural resources (sustainable environment). These issues are addressed, i.e., by an interdisciplinary initiative of the New European Bauhaus. The aim of the paper is to expand knowledge about beauty and utility. They are important when choosing mass-produced goods. The article uses research methods: interpretive research, analyses, comparisons, logical argumentation, etc. Experimental qualitative research using a checklist was used. The results expand the knowledge on the selected topic and research scope of the research of the paper. The survey can be used to rationally evaluate architecture, interiors, and design facilities. It can be helpful for various aesthetic and functional strategies dedicated to different users. The paper demonstrates the role of beauty and functionality in the built environment. They are analyzed in the context of social and technical conditions, as well as contemporary sustainable design

With the increase of mining range from shallow coal seam outcrops to deep With the increase of mining range from shallow coal seam outcrops to deep mining and the improvement of mining intensity in the mining area, there has been a phenomenon of no water inrush in shallow coal mines and abnormal water inrush in deep coal mines in karst landform areas of Guizhou.The project conducted a study on the water source of water inrush in the Xinhua mining area of Jinsha County, Guizhou Province. The research results indicate that the overlying Changxing Formation limestone of the Longtan Formation is a weak (conductive) aquifer, and there is no possibility of water inrush in normal stratigraphic blocks. The spatiotemporal distribution characteristics of the water inrush working face have verified that the Changxing Formation limestone in the shallow mined area has been damaged by mining activities, resulting in a large number of cracks in the rock mass and the formation of a large-scale water accumulation area, becoming a water source for the water inrush in the working face below and a fast supply channel for atmospheric precipitation. The analysis of surface water and mine water quality data shows that the water quality types of mine water and surface water are basically the same, and they are HCO3•SO4-Na type water. The correlation curve between mine water inflow and atmospheric precipitation verifies that the cycle of atmospheric precipitation supplying the mine in Jinyuan Coal Mine is about 10 months before pit closure, and 1 month after pit closure; The Changxing Formation limestone serves as a water-conducting channel, and atmospheric precipitation serves as a source of replenishment for mine water. The research results provide scientific basis for the treatment of atmospheric precipitation water damage in sudden water inrush mines (areas) under similar hydrogeological conditions.

This paper proposes a product design model for internalising users’ positive experiences through attachment. First, the research commences with a literature review to define the concepts and research status of positive experience design (PED) and product attachment. Subsequently, the design model is constructed, accompanied by relevant formulas for concept generation. Finally, the model’s validity is verified through a workshop, and its effectiveness is evaluated and discussed using the USE questionnaire. This study incorporates the seven factors of product attachment to activate positive states within the user–product relationship and facilitate the cultivation of positive thinking. Grounded in theories of PED and embracing a product attachment perspective, the attachment-driven PED model offers a systematic approach for generating design concepts that are relevant to user experience.

In the domain of financial trading, where accuracy and swift response to data discrep- ancies are paramount for maintaining clienttrust, our research paper delves into the development of a real-time alert system utilizing SpringBoot, a framework renowned for its robustness and adaptability in enterprise applications. We embark on a comprehensive journey, beginning with addressing thefoundational challenges inherent in monitoring trade inquiries - the necessity for real-time processing, unwavering data accuracy,and ensuring unwavering system reliability. The study then methodically transitions to the architectural design, where we explore howSpringBoot’s capabilities are optimally utilized to meet these challenges. Following this, we delve into the im- -plementationphase, detailing the strategic selection of compatible technologies and methods for effective data management and discrepancydetection. The paper culminates in a thorough evalu- ation of the system, where we assess performance across various operationalscenarios, scrutinize the accuracy of the discrepancy detection mechanisms, and integrate real-world feedback from users in thetrading sector. This holistic approach not only highlights the versatility and efficiency of SpringBoot in creating reliable alert systems in the high-stakes world of financial trading but also serves as a detailed guide for similar endeavors in this field

The ubiquitous deployment of Li-ion batteries (LIBs) in more demanding applications has reinforced the need to understand root-causes of thermal runaway. Herein we perform a forensic simulation of a real-case failure scenario, using localised heating of Li(Ni0.5Mn0.3Co0.2)O2 versus graphite 18650 cylindrical cells. This study determined the localised temperatures that would lead to venting and thermal runaway of these cells, as well as correlating the gases produced as a function of degradation pathway. Catastrophic failure, involving melting (with internal cell temperatures exceeding 1085°C), deformation and ejection of cell componentry, was induced by locally applying 200 °C and 250 °C to a fully charged cell. Conversely, catastrophic failure was not observed when the same temperatures were applied to the cells at lower state of charge (SOC). This work highlights the importance of SOC, chemistry and heat in driving the thermal failure mode of Ni-rich LIB cells, allowing for a better understanding of battery safety and associated design improvements.

The resolution of façade construction is not considered in the design process, as it can be expressed by complex technological innovations that emphasize the beauty of buildings. Nevertheless, resorting to this type of technology solution may not always be necessary. This study demonstrates this hypothesis through the investigation of five iconic case studies emphasizing the construction system analysis and the revelation of the brainwave idea. The brainwave idea defines the construction innovation that enables the detail by simplification rather than sophistication. Notable, unlike complex technological innovation, standard systems or elements applied strategically are considered little innovations to facilitate the resolutions of the façade complexity. Many of these innovations occur during the visual and constructive prototype progress required to validate the proposed solution and its performance. Therefore, real-scale prototype development that operates as a real-scale laboratory is necessary to correct and validate successive solutions.

Background: This research examines how market knowledge and artificial intelligence (AI) interact in different market designs such as business-to-business (B2B) settings while taking emerging technologies and the changing digitalization landscape into account. Objective: The main goal is to understand how AI affects market knowledge in different market designs such as business-to-business (B2B) contexts, taking into account language barriers, practical difficulties, and the revolutionary effects on decision-making and customer interactions. Result: They underscore the transformative potential of artificial intelligence (AI) by highlighting how it shapes market knowledge, encourages customized approaches, and improves marketing efficacy in the business-to-business (B2B) space. Conclusion: In order to create a path for responsible AI integration in B2B marketing, the study concludes with recommendations for standardized terminology related to AI, practical insights into implementation challenges, and ethical issues.

This paper is an extended version of a previously reported conference paper regarding low power design for NAND Flash. As the number of bits per NAND Flash die increases with cost scaling, IO datapath speed increases to minimize the page access time with scaled CMOS in IOs. The power supply for IO buffers, namely VDDQ, has decreased from 3V to 1.2V, accordingly. In this paper, how a reduction in VDDQ can contribute to power reduction in BL path is discussed and validated. Conventionally, BL voltage of about 0.5V has been supplied from a supply voltage source (VDD) of 3V. BL path power can be reduced by a factor of VDDQ to VDD when BL voltage is supplied from VDDQ. To maintain a sense margin at sense amplifiers, the supply source for BLs is switched from VDDQ to VDD before sensing. As a result, power reduction and equivalent sense margin can be realized at the same time. The overhead of implementing this operation is an increase in BL access time of about 2% for switching the power supply from VDDQ to VDD and an increase in die size of about 0.01% for adding the switching circuit, both of which are not significant in comparison with a significant power reduction in BL path power of NAND die of about 60%. The BL path was designed in 180nm CMOS to validate the design. When the cost for powering SSD becomes quite significant especially for data center, an additional lower voltage supply such as 0.8V dedicated to BL charging for read and program verify operations may be the best option for the future.

Background: The research is conducted against the backdrop of the rising incidence of diabetes and the demand for novel approaches to improve patient outcomes. With the goal of revolutionizing conventional methods and addressing the changing healthcare landscape, the study concentrated on the application of AI technology in diabetes treatment. Objective: Examining the various ways AI can be used in diabetes care and assessing how it can enhance automated screenings, tailored treatment recommendations, predictive modeling, and patient self-management were the main goals of the study. Result: The findings demonstrated how well AI works to anticipate a patient's unique reaction to a therapy, assist medical personnel in making decisions, and give patients more control over their own care. Artificial intelligence (AI)-powered solutions showed promise in improving real-time monitoring and encouraging patient adherence, supporting a comprehensive strategy for managing diabetes. Conclusion: The research indicates that artificial intelligence (AI) has great potential to change the way diabetes is treated. However, it also highlights the need for more research, ethical issues, and validation of AI. The results advocate for joint efforts to ensure responsible and patient-centered technology innovation in diabetes care and encourage the integration of AI with new technologies.

Safety limits application has always been a traditional approach to ensure the safe operation of electro-mechanical systems within many industries including automated vehicles, robotics, aerospace, traditional automotive, railways, manufacturing, etc. In all of these applications, control and safety limits are usually hard-coded into the production firmware and are fixed throughout the entire product life cycle. Currently, due to the evolving needs of automated systems like automated vehicles and robots, this traditional approach does not address all the use cases and scenarios to ensure safe operation. Especially for data-driven machine learning applications that constantly evolve and learn over time, it is important to be able to adjust the safety limits application strategy to be more flexible and adaptable based on different Operational Design Domains (ODDs) and scenarios. Our ITSC conference paper ~\cite{4} introduced the concept of a new safety limits application strategy called the Dynamic Control Limits Application (DCLA) strategy that supports the flexible application of diverse limits profiles based on the parameters involved within the dynamic scenario at different layers of the Autonomy software stack.This paper extends the DCLA strategy to derive the complete methodology for safety limits application based on ODD elements, scenario identification and scenario classification using Decision Making Engines. It leverages the layered architecture introduced in the ITSC conference paper to implement the Decision Making (DM) algorithms. Another important extension is the use of cloud infrastructure that is based on the Vehicle-to-Infrastructure (V2I) technology to store the scenarios and the limits mapping to serve as a ground truth and/or a backup mechanism in case of errors or failures associated with the main Decision Making (DM) Engine. There is also a focus on providing a more comprehensive list of scenarios and a custom built experimental dataset to cover the maximum ODD elements, and multiple tables of safety limits to be chosen from, which eventually helps in creating different safety limits application profiles. These distinct safety limits application profiles are based on the scenario parameters that are perceived by the system upon which the Decision Making algorithms are applied or trained. This systematic approach can be used within the industry for any of the future automated vehicles and systems until Level 5 Autonomy.

This paper introduces an innovative nanotechnology-based approach that provides a pathway to enhance the energy release efficiency of nanoenergetic materials (nEMs) by harnessing self-synchronized collective atomic vibrations and phonon wave resonance within the transition domains between nanocomponents, without altering the material composition. The key innovation involves incorporating finely-tuned 2D-ordered linear-chain carbon-based multilayer nano-enhanced interfaces as programmable nanodevices into the transition domains using advanced multistage processing and assembly techniques. These programmable nanodevices enable precise control over self-synchronized collective atomic vibrations and phonon wave propagation, leading to synergistic effects. To activate and optimize these effects, a combination of various methods is employed, including energy-driven initiation of allotropic phase transformations, surface acoustic wave-assisted micro/nano-manipulation, heteroatom doping, directed self-assembly using high-frequency electromagnetic fields, and data-driven inverse design approaches. By leveraging a data-driven inverse design strategy and uncovering hidden structure-property relationships, we maximize energy release efficiency using the carbon nano-materials genome approach derived from multifactorial neural network-based predictive models. This approach not only unlocks new functionalities in nEMs but also improves environmental performance and safety levels. By pioneering transformative pathways for nEMs through harnessing phonon wave resonance in low-dimensional nanocarbon transition interfaces, this research brings significant advancements in the field.

This study sought to improve the nutritional, functional and biochemical properties of pearl millet through malting and fermentation. Moringa oleifera leaf powder (MLP) was used as a fortificant. Mixture design was used to find optimal proportions for each of the components that yield a high protein and or low saturated fat content. Twelve mixtures with varying ratios of fermented, and malted pearl millet flour ranging between 30–65%, and MLP between 5–15% were generated through I-Optimal mixture design. The mixtures were wet-cooked, freeze-dried and analyzed for protein and fat content. The data obtained were fitted to a linear mixture model and the search for the optimum was done using Numerical Optimization for maximising protein and minimising saturated fat. The linear model was suitable for explaining variation for total protein and saturated fat with r2 of 0.50 and 0.51, respectively. Increasing MLP increased protein content. Two final formulations were generated through the optimization process. Pearl millet’s protein content increased by up to 22% while saturated fat decreased by up to 13%. Ash content increased by 75%. Polyphenol content and oxygen radical absorbance capacity increased by 80% and 25%, respectively. Final and peak viscosity were reduced by 90% and 95%, respectively.

AbstractCurrently, public health researchers are investigating several complex and multi-faced health problems that require mixed-method approaches (MMA) to clearly understand problems and design proper intervention approaches and policy formulation. Besides, a comprehensive comprehension of the complex operation of society is vital. The MMA helps in having a broader understanding of the functioning and structure of the community at large. MMA deliberately integrates qualitative and quantitative approaches carefully to build on the merits of each other and confirm that the findings of research are closer to the truth. Therefore, public health scholars must have an excellent comprehension of the MMA and its philosophical foundations for discovering the complex conditions that challenge public health nowadays. However, public health researchers do not clearly understand the theoretical underpinnings and practical application of MMA, despite its popularity in developing countries. Therefore, this article aimed to provide comprehensive evidence on the theoretical underpinnings and practical application of MMA.

This research raises questions about the possibilities and options of using BIM methodology for wood design and construction associated with software for structure modeling along the asset's cycle life. Likewise, several academic and research initiatives are reviewed. In this sense, this paper aims to establish an appropriate link between two agendas that the architecture, engineering, and construction (AEC) industry, academia, and governments normally handle separately. By conducting several literature reviews (book, journals, and congresses) and extensive software tests (BIM software: Revit, Archicad, Tekla, and Wood plug-ins: AGACAD, Archiframe, Timber Framing 2015, WoodStud Frame, etc.), the state-of-the-art was assessed in both fields, several cases linking BIM and wood are shown in detail and discussed, various theoretical samples are modelled and shown, and the advantages and disadvantages of each technique and stage are explained. On the other hand, although wood construction has been the most common for hundreds of years, this is not the case of BIM Modeling software developments associated with this materiality. Furthermore, since the appearance of materials such as steel and reinforced concrete, all software developments have focused on these materials, leaving aside the possibility of developing applications for use in wood projects. According to previously discussed, it can be concluded that BIM for Wood has been used more frequently in academia and that both fields have several common processes and, in many cases, only a few BIM-wood tools have been used. Thus, disregarding the high potential and high level of benefits that results with the application of these methodologies for the complete building life cycle (design, construction, and operation).

Human language and social cognition are two key disciplines that have traditionally been studied as separate domains. However, emerging research from detailed studies of comparative animal behavior, human social behavior, language acquisition in children, social cognitive neuroscience, and the cognitive neuroscience of language suggest that language and social cognition are two deeply interrelated capacities of the human species. For instance, recent developmental studies on the acquisition of language in infants and young children, draw attention to the important crucial benefits associated with several different aspects of social stimulation for youngsters, including the quantity and quality of linguistic input, dyadic infant/child-to-parent verbal and non-verbal social interactions, and other important social cues integral for facilitating language learning and social bonding. Studies of the adult human brain further suggest a high degree of specialization for sociolinguistic information processing, memory retrieval, and comprehension, suggesting the function of these regions may link language with social cognition and social bonding. In effect, the social brain and social complexity hypotheses may jointly help to explain how neurotypical children and adults learn language, why autistic adults and children exhibit simultaneous deficits in language and social cognition, and why nonhuman primates and other animals with significant computational abilities do not acquire the capacity for language. But perhaps most critically, the following article argues that this and related research will allow scientists to generate a holistic profile and deeper understanding of the healthy adult social brain, while developing more innovative and effective diagnoses, prognoses, and treatments for maladies and deficits also associated with the social brain.

Langya Henipavirus (LayV) is a new zoonotic Henipavirus reported in 2022. Patients infected by LayV show common cold symptoms, such as fever, fatigue, and cough. Non-fatal cases associated with this virus have been reported in Henan and Shandong provinces in China. Should human-to-human transmission occur, it has the potential to be a pandemic like SARS-CoV-2. LayV is an enveloped negative-sense RNA virus. Its polymerase (encoded by the L gene) is considered a conserved target shared within Henipavirus viruses, allowing for qPCR detection, in which primers play a pivotal role. For the development of a diagnostic kit, we designed three primer sets targeting the L gene and evaluated their detection of plasmids carrying part of the L gene. Primer sets 1 and 2 were found to be suitable for further sensitivity, specificity, and efficiency testing. Both primer sets were able to amplify PCR products in the presence of human saliva, and both the melt curve analysis and gel electrophoresis showed distinct peaks and bands, supporting the specificity of the qPCR primers. Based on standard curve analysis, both primers detected as low as approximately 1000 copies of the L gene. Given the specificity and robustness to work in the presence of saliva, the primers can be used for pandemic-preparedness in LayV detection.

In northern Canada where permafrost is prevalent, a shortage of accessible, affordable, and high-quality housing has been ongoing for decades. Design of foundations in permafrost presents unique engineering challenges due to permafrost soil mechanics and climate change. There is no specific design code for pile or shallow foundations in northern Canada. Consequently, the design process heavily relies on the expertise and experience of Arctic geotechnical engineers who have specialized knowledge in this field. Therefore, a comprehensive review of the practice or literature in foundation design in the Arctic would be necessary. The main objective of this review paper is to provide an overview of the common foundations in permafrost and the techniques adopted to counteract the effects of frozen soils. This study conducted a literature review of state-of-the-art practices on deep and shallow foundations used in northern Canada, including common steel pipe piles and thermosyphons. The review summarized the current principles, including adfreeze strength, creep settlement, and frost heave, used in the foundation design in permafrost. Then this paper summarized the findings from interviewing several engineers or professionals who have experiences in the design of foundations in permafrost. The interviews revealed the technical and non-technical aspects of foundation design practice in northern Canada. Lastly, in order to demonstrate the design methods, the paper presented two examples where screw piles and steel pipe piles were designed to support a residential building in northern Canada, according to the state-of-practice criteria for adfreeze strength, long term settlement and frost heave.