Copper(I) sulfide (Cu2S) is a low-cost, earth-abundant, and non-toxic thermoelectric material for applications in the middle-high temperature range (>650 K). Although 3D printing these materials can simplify their manufacturing, elevated temperatures observed during sintering impair their crystal structure and energy conversion efficiency. In this study, we demonstrated a novel post-processing methodology to revert the thermoelectric properties of the 3D printed Cu2-xS materials back to the unimpaired state via sulfur infusion. After printing and sintering, sulfur was infused into the specimens under vacuum to optimize their crystal structure and achieve high thermoelectric efficiency. Chemical analysis and X-ray Diffraction (XRD) tests showed that after the sulfur infusion process, the Cu/S ratio was reverted close to the stoichiometric level. 3D printed Cu2-xS showed p-type thermoelectric behavior with electrical conductivity peaking at 143 S-cm-1 at 750 K and Seebeck coefficient of 175 µV-K-1 at 627 K. Figure of merit (ZT) value of 1.0 at 780 K was achieved which is the highest value ever reported for a 3D printed Cu2-xS thermoelectrics at this temperature. Fabrication of environmentally friendly thermoelectric materials with extended dimensional freedom and conversion efficiency has the potential to impact the thermoelectric industry with new energy conversion applications and lowered manufacturing costs.

The spike protein (S) of SARS-CoV-2 has been shown to bind to the human angiotensin-converting enzyme 2 (ACE2) receptor with much higher affinity compared to other coronaviruses. The binding interface between the ACE2 receptor plays a critical role in the entry mechanism of SARS-CoV-2 virus. There are specific amino acids involved in the interaction between S protein and ACE2 receptor. This specificity is critical for the virus to establish a systemic infection and cause COVID-19 disease. In the ACE2 receptor, the largest number of amino acids that play a crucial role in the mechanism of interaction and recognition with the S protein are located in the C-terminal part which represents the main binding region between ACE2 and S. This fragment is abundant in coordination residues such as aspartates, glutamates and histidine that could be targeted by metal ions. Zn²⁺ ion binds to the ACE2 receptor in its catalytic site and modulates its activity, but it could also contribute to the structural stability of the entire protein. The ability of the human ACE2 receptor to coordinate metal ions, such Zn²⁺, in the same region where it binds to the S protein could have a crucial impact in the mechanism of recognition and interaction of ACE2-S with consequences on their binding affinity that deserve to be investigated. To test this possibility, this study aims to characterize the coordination ability of Zn²⁺, and also Cu²⁺ for comparison, with selected peptide models of the ACE2 binding interface using spectroscopic and potentiometric techniques.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

This article presents, for the first time, the kinetics and the general conversion features of a 3-initiator system (A/B/N), based on proposed mechanism of Mokbel et al, for both free radical polymerization (FRP) of acrylates and the free radical promoted cationic polymerization (CP) of epoxides using copper complex as the initiator. Higher FRP and CP conversion can be achieved by co-initiators concentration [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals S' and S. The FRP and CP conversion is proportional to, respectively, the nonlinear and linear power of bI[A][B], where b and I are the absorption coefficient and the light intensity, respectively. System in air has lower conversion than in laminate due to the oxygen inhibition effects. For thick samples (with thickness z), there is an optimal concentration [A*] which is inverse proportional (bzI), in contrast with very thin sample, in which the conversion is an increasing function of [A] and [B]. The unique feature of dark polymerization in CP conversion enables the polymerization to continue in living mode, in contrasts with that of the radical-mediated pathway in most conventional FRP. The measured results of Mokbel et al are well analyzed and matching the predicted features of our modeling.

The aim of the research was a comprehensive evaluation of concrete using the EIPI method. In the evaluation the compressive strength of concrete and its durability properties represented by sorptivity and air permeability were taken into account. Since copper slag waste with increased natural radioactivity was used in the assessed concrete, additional evaluation was carried out taking into account the influence of natural radioactivity within the performance index. Also the reference concrete, which was made without the use of copper slag waste, was evaluated for comparative purposes. In order to make the evaluation as comprehensive as possible, the concrete made with the use of three types of cement was subjected to the assessment: CEM I, CEM II and CEM III. The results show that in both approaches the best result was achieved by concrete with CEM III cement. If natural radioactivity is not taken into account in the evaluation, the best result is obtained by concrete made with copper slag waste, and if radioactivity is considered, the best result is obtained with concrete without addition of the waste. It follows from the above that although natural radioactivity has a significant impact on the EIPI evaluation result, the decisive factor is still the type of cement.

Angiogenin (ANG), an endogenous protein that plays a key role in cell growth and survival, has been scrutinised here as promising nanomedicine tool for the modulation of pro-/ anti-angiogenic processes in brain cancer therapy. Specifically, peptide fragments from the putative cell membrane binding domain (residues 60-68) of the protein were used in this study to obtain peptide-functionalised spherical gold nanoparticles (AuNPs) of about 10 nm and 30 nm in optical and hydrodynamic size, respectively. Different hybrid biointerfaces were fabricated by peptide physical adsorption (Ang60-68) or chemisorption (the cysteine analogous Ang60-68Cys) at the metal nanoparticle surface, and the cellular assays were performed in the comparison with ANG-functionalised AuNPs. Cellular treatments were performed both in basal and in copper-supplemented cell culture medium, to scrutinise the synergic effect of the metal, which is another known angiogenic factor. Two brain cell lines were investigated in parallel, namely tumour glioblastoma (A172) and neuron-like differentiated neuroblastoma (d-SH-SY5Y). Results on cell viability/proliferation, cytoskeleton actin, angiogenin translocation and VEGF release pointed to the promising potentialities of the developed systems as anti-angiogenic tunable nanoplaftforms in cancer cells treatment.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Cadmium (Cd) is an environmental toxicant of worldwide public health significance. Diet is the main non-workplace Cd exposure source other than smoking. The intestinal absorption of Cd involves the transporters for iron, zinc, copper, and calcium. These metal transporters essentially determine the body burden of Cd because only 0.001-0.005% of Cd accumulated in the body can be excreted in urine each day. The International Agency for Research on Cancer listed Cd as a human lung carcinogen. Current evidence, however, suggests that environmental Cd may increase the prevalence of many types of cancer, notably lung, liver, breast, pancreas, and kidney. A two-year bioassay that mimics a lifelong exposure demonstrates Cd caused neoplasms in multiple tissues of mice. Also, several non-tumorigenic human cell lines underwent malignant cell transformation, when they were exposed to a sublethal dose of Cd for a prolonged time. Cd does not directly damage DNA, but it can profoundly affect gene expression through its interactions with various proteins, and Cd can thus be viewed as a transcription modulator. The present review highlights epidemiological studies that connected an enhanced risk of various neoplastic diseases to chronic exposure to environmental Cd. Special emphasis is on the impact of body iron stores on the absorption rate of Cd, and its implications for breast cancer prevention in highly susceptible subpopulation groups of women. Resistance to cell death and other cancer phenotypes acquired during Cd-induced cancer-cell transformation, under in vitro conditions, are briefly discussed. The potential role for ZnT1 efflux transporter in cellular acquisition of tolerance to Cd cytotoxicity are highlighted.

With the growing demand for personal protective equipment (PPE) in the face of the pandemic events caused by SARS-COV-2, the opportunity arises for the development of materials with characteristics such as antimicrobial, antiviral, antifungal activity, etc. The use of polymeric nanocomposites based on polyester/copper offers an alternative of great interest due to the versatility of the raw material and the high efficiency of copper as an antimicrobial additive. In this study, textile fibers prototypes with different Cu nanoparticles (CuNP) content were produced using melt-spinning to obtain bi-component multifilament fibers, and melt-blowing to obtain non-woven fabrics. The prototypes were tested against different pathogenic microorganisms such as S. aureus, E. coli, and C. albicans. It was shown that bi-component fibers offer more excellent protection against pathogens, while non-woven fabric only shows activity against E. coli. It was possible to identify that the CuNP were confined exclusively in the outer cover of the bi-component fibers, using different analytical techniques, which may be associated with the increase in antimicrobial activity, compared to the fibers present in the non-woven fabric, even when they present the same CuNP content.

Various methods including electrochemical purification, chemical precipitation, solvent extraction, and ion-exchange resins, have maturely been used for removal of copper from nickel anolyte. Interestingly, these approaches of copper removal from nickel anolyte by precipitation are well used as the primary industrial method in nickel production again. However, these methods suffer from several severe drawbacks in industrial practices. One is that a small amount of nickel precipitates with copper in slags，resulting in slag treatment difficulties. Second, this process requires an extremely high activity of the sulfide-based copper removal agents which results in high production costs; the short storage period of the copper removal agent is another drawback of this method. These have been the key challenges in the smelting process of nickel. Herein, we present a comprehensive review of the nickel removal methods used for nickel anolyte purification, electrochemical purification, chemical precipitation, solvent extraction, and ionexchange resins. The advantages and feasibilities of each technique in industrial applications are also explored and analyzed. Finally, we demonstrate that ion-exchange resin-based extraction method can pave a new path for metallurgical research on nickel.

In response to long-lasting high levels of Metallic Trace Elements (MTEs) in urban soils, we expect soil invertebrates inhabiting urban environments to have evolved detection and avoidance and/or tolerance mechanisms to MTE pollution. In this study, I used artificial soils with concentrations of lead, zinc, copper, chromium and nickel that reflect pollution levels in soils of Parisian parks. Using choice experiments, I compared habitat preference (i.e. the occurrence of individuals in the polluted vs. unpolluted soil) and health status (i.e. body mass maintenance, mobility, mortality) between three species of endogeic earthworms – Apporectodea caliginosa, Apporectodea icterica and Allolobophora chlorotica – originating either from urban or rural grasslands. This study highlights a clear avoidance of MTE polluted soils in all three species, as well as MTE-induced health impairments, especially in A. chlorotica. Interestingly, earthworm response to MTE exposure only slightly differed between earthworms from urban and rural origin, suggesting the absence of widespread acclimatization or adaptation mechanisms to MTE pollution in cities. As a consequence, MTE pollution is expected to significantly shape earthworm spatial distribution in both urban and rural environments and, as a consequence, affect ecosystem functioning.

Aquatic animals have unique physiological mechanisms to absorb and retain minerals from their diets and water. Research and development in the area of mineral nutrition of farmed fish and crustaceans have been relatively slow and major gaps exist in the knowledge of trace element requirements, physiological functions and bioavailability from feed ingredients. Quantitative dietary requirements have been reported for three macroelements (calcium, phosphorus and magnesium) and six trace minerals (zinc, iron, copper, manganese, iodine and selenium) for selected fish species. Mineral deficiency signs in fish include reduced bone mineralization, anorexia, lens cataracts (zinc), skeletal deformities (phosphorus, magnesium, zinc), fin erosion (copper, zinc), nephrocalcinosis (magnesium deficiency, selenium toxicity), thyroid hyperplasia (iodine), muscular dystrophy (selenium) and hypochromic microcytic anaemia (iron). An excessive intake of minerals from either diet or gill uptake causes toxicity and therefore a fine balance between mineral deficiency and toxicity is vital for aquatic organisms to maintain their homeostasis either through increased absorption or excretion. Release of minerals from uneaten or undigested feed and from urinary excretion can cause eutrophication of natural waters, which requires additional consideration in feed formulation. The current knowledge in mineral nutrition of fish is briefly reviewed.

. This article presents, for the first time, the kinetics and the general features of a photopolymerization system (under visible light) G1/ Iodonium/ TEA/gold chloride (or A/B/N/G), having initial concentrations of A0, B0, N0 and G0, based on the proposed mechanism of Tar et al. Analytic formulas are developed to explore the new features including: (i) both FRP efficacy and the production of nanogold (NG) are proportional to the relative concentration ratios of (A0+B0+N0)/G0, which may be optimized for maximum efficacy; (ii) the two competing procedure of NG production and efficacy of free radical photopolymerization (FRP) can be tailored for optimal system with nanogold in the polymer matrix;(ii) the FRP efficacy is contributed by 3 components: the coupling of the excited state of copper complex (T) with the radicals (R and S) produced by the iodonium and the amine; (iii) the production of NG is contributed by 2 components: the coupling of T and radical (S) with gold ion; (iv) NG production has a transient state value which is an increasing function of light intensity and the combined concentration ratio [(A0/G0)+(N0/(K'M0). whereas it has a steady-state independent to the light intensity.

Here we report the effect of substrate, sonication process, and post-annealing on the structural, morphological, and optical properties of ZnO thin films grown in the presence of isopropyl alcohol (IPA) at temperature 30 – 65 ℃ by successive ionic layer adsorption and reaction (SILAR) method on both soda lime glass (SLG) and Cu foil. The X-ray diffraction (XRD) patterns confirmed the preferential growth thin films along (002) and (101) plane of wurtzite ZnO structure while grown on SLG and Cu foil substrate respectively. Both XRD and Raman spectra confirmed the ZnO and Cu-oxide phases of the deposited films. Scanning electron microscope (SEM) image of the deposited films shows compact and uniformly distributed grains for samples grown without sonication while using IPA at temperature 50 and 65 ℃. The post-annealing treatment improves the crystallinity of the films, further evident by XRD and transmission and reflection results. The estimated optical bandgaps are in the range of 3.37-3.48 eV for as-grown samples. Results revealed that high-quality ZnO thin films could be grown without sonication using IPA dispersant at 50 ℃, which is much lower than the reported results using the SILAR method. This study suggests that in the presence of IPA, the SLG substrate results in better c-axis oriented ZnO thin films than that of DI water, ethylene glycol, propylene glycol at the optimum temperature of 50 ℃. Air-annealing of the samples grown on Cu foils induced the formation of Cu_xO/ZnO junctions which is evident from the characteristic I-V curve including the structural and optical data.

The impact of metals bioaccumulation on marine organisms is under investigation. This study was designed to determine the association of oxidative stress in mussels Mytilus galloprovincialis induced by seawater enriched with trace metals with protein synthesis. Mussels were exposed to 40 μg/L Cu, 30 μg/L Hg, or 100 μg/L Cd for 5 and 15 days, and the pollution effect was evaluated by measuring established oxidative biomarkers. The results showed damage on the protein synthesis machine integrity and specifically, on translation factors and ribosomal proteins expression and modifications. Exposure of mussels to all metals caused oxidative damage that was milder in the cases of Cu and Hg, and more pronounced for Cd. However, after prolonged exposure of mussels to Cd (15 days), the effects receded. These changes that perturb protein biosynthesis can serve as a great tool for elucidating the mechanisms of toxicity and could be integrated in biomonitoring programs.

The aim of this work is to assess the influence of Friction Stir Welding (FSW), process parameters, optimized tool traveling speed, and corrosion resistance of the 0.95 Mg-Al-alloy and pure copper weldment. Samples of aluminum-copper with and without deformation were characterized to investigate the metallurgical effects created during the welding deformation process. Effect of process parameters on microstructure and corrosion rate have been investigated for all the samples. All the electrochemical and polarization tests were done in 3.5 wt.% NaCl solution. Scanning Kelvin Probe (SKP) was done to detect the localized corrosion on the surface. Optical micrography observation indicated that the primary α-Al phase, which was formed during solidification can effectively limit the growth of Cu₉Al₄ phase. Finer acicular α-Al precipitates were observed in CuAl matrix during joining process that tends to coarser with the increase in tools travel speed. The electrochemical and polarization results showed that among all the tool travelling speed the specimen joined at tool travelling speed of 40 mm/min shows the best non-corrosive property.

Many theoretical models of iron-based superconductors have been proposed but Tc calculations based on the models are usually missing. We have chosen two models of iron-based superconductors in the literature and then compute the Tc values accordingly: Recently two models have been announced which suggest that superconducting electron concentration involved in the pairing mechanism of iron-based superconductors may have been underestimated, and that the antiferromagnetism and the induced xy potential may even have a dramatic amplification effect on electron-phonon coupling. We use bulk FeSe, LiFeAs and NaFeAs data to calculate the Tc based on these models and test if the combined model can predict the superconducting transition temperature (Tc) of the nanostructured FeSe monolayer well. To substantiate the recently announced xy potential in the literature, we create a two-channel model to separately superimpose the dynamics of the electron in the upper and lower tetrahedral plane. The results of our two-channel model support the literature data. While scientists are still searching for a universal DFT functional that can describe the pairing mechanism of all iron-based superconductors, we base on the ARPES data to propose an empirical combination of DFT functional for revising the electron-phonon scattering matrix in the superconducting state, which ensures that all electrons involved in iron-based superconductivity are included in the computation. Our computational model takes into account this amplifying effect of antiferromagnetism and the correction of the electron-phonon scattering matrix together with the abnormal soft out-of-plane lattice vibration of the layered structure, which allows us to calculate theoretical Tc values of LiFeAs, NaFeAs and FeSe as a function of pressure that correspond reasonably well to the experimental values. More importantly, by taking into account the interfacial effect between an FeSe monolayer and its SrTiO3 substrate as an additional gain factor, our calculated Tc value is up to 91 K high, and provides evidence that the strong Tc enhancement recently observed in such monolayers with Tc reaching 100 K may be contributed from the electrons within the ARPES range.

Mycobacterium tuberculosis (Mtb) is the etiological agent of tuberculosis (TB), a disease that alt-hough preventable and curable, remains a global epidemic due to the emergence of resistance and a latent form responsible for a long period of treatment. Drug discovery in TB is a challenging task due to the heterogeneity of the disease, the emergence of resistance and an uncomplete knowledge of the pathophysiology of the disease. The limited permeability of the cell wall and the presence of multiple efflux pumps remain a major barrier to achieve effective intracellular drug accumulation. While the complete genome sequence of Mtb has been determined and several potential protein targets have been validated, the lack of adequate models for in vitro and in vivo studies is a limit-ing factor in TB drug discovery programs. In current therapeutic regimens, less than 0.5% of bac-terial proteins are targeted being the biosynthesis of the cell wall and the energetic metabolism two of the most important processes exploited for TB chemotherapeutics. This review provides an overview on the current challenges in TB drug discovery and emerging Mtb druggable proteins, and how chemical probes for protein profiling enabled the identification of new targets and bi-omarkers, paving the way to disruptive therapeutic regimens and diagnostic tools.

Lake Rawapening, Semarang Regency, Indonesia, has incorporated a holistic plan in its management practices. However, despite successful target achievements, some limitations remain that a review of its management plan is needed. This paper identifies and analyzes existing lake management strategies as a standard specifically in Lake Rawapening by exploring various literature, both legal frameworks and scholarly articles indexed in Google Scholar and published in Water by MDPI about lake management in many countries. There are two major types of lake management, namely pillar-based and object-based. While the former is the foundation of a conceptual paradigm that does not comprehensively consider the roles of finance and technology in the lake management, the latter indicates the objects to manage so as to create standards or benchmarks for the implementation of various programs. Overall, Lake Rawapening management should include more programs on erosion-sedimentation control and monitoring of operational performance using information systems.

Nature-based solutions (NbS) are increasingly recognised for their potential to address both the climate and biodiversity crises. These outcomes are interdependent, and both rely on the capacity of NbS to support and enhance the health of an ecosystem: its biodiversity, the condition of its abiotic and biotic elements, and its capacity to function normally despite environmental change. However, while understanding of ecosystem health outcomes of nature-based interventions for climate change mitigation is growing, the outcomes of those implemented for adaptation remain poorly understood with evidence scattered across multiple disciplines. To address this, we conducted a systematic review of the outcomes of 109 nature-based interventions for climate change adaptation using 33 indicators of ecosystem health across eight broad categories (e.g. diversity, biomass, ecosystem functioning and population dynamics). We showed that 88% of interventions with positive outcomes for climate change adaptation also reported measurable benefits for ecosystem health. We also showed that interventions were associated with a 67% average increase in local species richness. All eight studies that reported benefits in terms of both climate change mitigation and adaptation also supported ecosystem health, leading to a triple win. However, there were also trade-offs, mainly for forest management and creation of novel ecosystems such as monoculture plantations of non-native species. Our review highlights two major limitations of research to date. First, only a limited selection of metrics are used to assess ecosystem health and these rarely include key aspects such as functional diversity and habitat connectivity. Second, taxonomic coverage is poor: 67% of outcomes assessed only plants and 57% did not distinguish between native and non-native species. Future research addressing these issues will allow the design and adaptive management of NbS to support healthy and resilient ecosystems, and thereby enhance their effectiveness for meeting both climate and biodiversity targets.

This study explores the stability of electrodeposited copper catalysts utilized in electrochemical CO2 reduction (ECR) across various amine media. The focus is on understanding the influence of different amine types, corrosion ramifications, and the efficacy of pulse ECR methodologies. Employing a suite of electrochemical techniques including potentiodynamic polarization, linear resistance polarization, cyclic voltammetry, and chronopotentiometry, the investigation reveals useful insights. The findings show that among the tested amines, CO2-rich monoethanolamine (MEA) exhibits the highest corrosion rate. However, in most cases the rates remain within tolerable limits for ECR operations. Primary amines, notably monoethanolamine (MEA), show enhanced compatibility with ECR processes, attributable to their resistance against carbonate salt precipitation and sustained stability in potential over extended durations. Conversely, tertiary amines such as methyldiethanolamine (MDEA) present challenges due to the formation of carbonate salts during ECR, impeding their effective utilization. The study highlights the effectiveness of pulse ECR strategies in stabilizing ECR. A noticeable shift in cathodic potential and reduced deposit formation on the catalyst surface through periodic oxidation underscores the efficacy of such strategies. These findings offer insights for optimizing ECR in amine media, thereby providing promising pathways for advancements in CO2 emission reduction technologies.

Polyimide (PI) films are widely used in electronic devices owing to their excellent mechanical and electrical properties and high thermal and chemical stabilities. In particular, PI films play an important role in flexible printed circuit boards (FPCBs). However, one challenge currently faced with their use is that the adhesives used in FPCBs cause a high dielectric loss in high-frequency applications. Therefore, it is envisioned that PI films with a low dielectric loss and Cu films can be used to prepare two-layer flexible copper clad laminates (FCCLs) without any adhesive. However, the preparation of ultra-thin FCCLs with no adhesives is difficult owing to the low peel strength between the PI films and Cu films. To address this technical challenge, an FCCL with no adhesive was prepared by high-power helicon wave plasma (HWP) treatment. The surface roughness of the PI film and the peel strength between the PI film and Cu film were measured. The experimental results showed that the surface roughness of the PI film increased by 40-65% and the PI film demonstrated improved adhesion (the peel strength was >8.0 N/cm) with the Cu film following plasma treatment and Cu plating.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

Macroautophagy/autophagy plays an important role in cellular copper clearance. The means by which the copper metabolism and autophagy pathways interact mechanistically is vastly unexplored. Dysfunctional ATP7B, a copper-transporting ATPase, is involved in the development of monogenic Wilson disease, a disorder characterized by disturbed copper transport. Using in silico prediction, we found that ATP7B contains a number of potential binding sites for LC3, a central protein in autophagy pathway, so-called LC3 interaction regions (LIRs). The conserved LIR3, located at the C-terminal end of ATP7B, was found to directly interact with LC3B in vitro. Replacing the two conserved hydrophobic residues W1452 and L1455 of LIR3 significantly reduced interaction. Furthermore, autophagy was induced in normal human hepatocellular carcinoma cells (HepG2) leading to enhanced colocalization of ATP7B and LC3B on the autophagosome membranes. By contrast, HepG2 cells deficient of ATP7B (HepG2 ATP7B-/-) showed autophagy deficiency at elevated copper condition. This phenotype was complemented by heterologous ATP7B expression. These findings suggest a cooperative role of ATP7B and LC3B in autophagy-mediated copper clearance.

Mechanical robustness, biocompatibility, and antibacterial performances are key features for materials suitable to be used in tissue engineering applications. In this work, we investigated the link existing between structural and functional properties of TiCu(Ag) thin films deposited by physical vapor deposition magnetron sputtering on Si substrates. The thin films were characterized by X-ray diffraction (XRD), nanoindentation, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The TiCu(Ag) thin films showed complete amorphous structure and improved mechanical properties in comparison with pure Ti films. However, for contents in excess of 20% Ag, we observed the appearance of nanometric Ag crystallite. The TiCu(Ag) thin films displayed excellent biocompatibility properties, allowing adhesion and proliferation of the human fibroblasts MRC-5 cell line. Moreover, all the investigated TiCu(Ag) alloy display bactericidal properties, preventing the growth of both Pseudomonas aeruginosa and Staphylococcus aureus. Results obtained from biological tests have been correlated to the surface structure and microstructure of films. The excellent biocompatibility and bactericidal properties of these multifunctional thin films opens to their use in tissue engineering applications.

Efficient oxygen evolution reaction (OER) electrocatalysts are highly desired in the field of water electrolysis and rechargeable metal-air batteries. In this study, a chelate polymer, composed of copper (II) and dithiooxamide, was used to derive an efficient catalytic system for OER. Upon potential sweep in 1M KOH, copper (II) centers of the chelate polymer were transformed to CuO and Cu(OH)2. The carbon-dispersed CuO nanostructures formed a nanocomposite which exhibits an enhanced catalytic activity for OER in alkaline media. The nanocomposite catalyst has overpotential of 280 mV (at 1 mA/cm2) and a Tafel slope of 81 mV/dec in 1M KOH solution. It has a seven-fold higher current than IrO2/C electrode, per metal loading. A catalytic cycle is proposed, in which, CuO undergoes electrooxidation to Cu2O3 that further decomposes to CuO with releasing oxygen. This work reveals a new method to produce an active nanocomposite catalyst for OER in alkaline media using a non-noble metal chelate polymer and a porous carbon. This method can be applied to the synthesis of transition metal oxide nanoparticles used in the preparation of composite electrodes for water electrolyzers and can be used to derive cathode materials for aqueous-type metal-air batteries.

Real-time evolution of the electron densities under excitations in La₂CuO₄ was calculated by the time-dependent density functional theory (TDDFT). The author found, for the first time, under excitations, the electron cloud of Cu²⁺ changes obviously and the characteristic frequencies are 83 meV and 36 meV, respectively, for two different modes. The results are unexpected and close to that of lattice vibrations. The results show that the electron cloud of Cu²⁺ (just like the lattice) can be the electron-pairing medium in high temperature copper oxide superconductors.

Chitosan decorated copper nanoparticles (CS/CuNPs) catalysts were synthesized via reduction methods utilizing green protocol. The CS/CuNPs hybrid catalysts were tested for the synthesis of quinoline derivatives utilizing one-pot multicomponent reaction (MCR) under ultrasonic irradiation. The best catalyst (CS/CuNPs) that provided good conversion reaction yield and high turnover frequency (TOF) was characterized using Fourier transform infrared (FTIR), Thermogravimetric analyses (TGA), X-ray diffraction (XRD), , scanning electron microscopy (SEM), transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) techniques. Generalization of the scope of the proposed catalytic process was studied using different aldehydes. Excellent products yield and high TOF in even shorter reaction time (~5 min) was attained. Recyclability performance of the catalyst over five times re-use without detectable loss in product yield was recorded. The current method is green process utilizing environmentally benign catalyst and considered to be promising sustainable protocol for the synthesis of fine chemicals.

There is an urgent demand worldwide for the development of highly selective adsorbents and sensors of heavy metal ions and other organic pollutants. Within these environmental and public health frameworks, we are combining the salient features of clays and chelatant polymers to design selective metal ion adsorbents. Towards this end, the ion imprinting approach has been used to develop a novel nanohybrid material for the selective separation of Cu2+ ions in aqueous solution. The Cu2+-imprinted polymer/ montmorillonite nanocomposite (IIP/Mt) and non-imprinted polymer/montmorillonite nanocomposite (NIP/Mt) were prepared by radical photopolymerization process in the visible light. Ion imprinting was indeed important as the recognition of copper ions by IIP/Mt was significantly superior to that of NIP/Mt that is the nanocomposite synthesized in the same way but in the absence of Cu2+ ions. The adsorption process as batch study was investigated under the experimental condition affecting same parameters such as contact time, concentration of ions metals and pH. The adsorption capacity of Cu2+ ions is maximized at pH 5. Removal of Cu2+ ion achieved equilibrium within 15 minutes; the results obtained were found to be fitted by the pseudo-second order kinetics model. The equilibrium process was well described by the Langmuir isothermal model and the maximum adsorption capacity was found to be 23.6 mg/g.

The new mineral species oyonite, ideally Ag3Mn2Pb4Sb7As4S24, has been discovered in the Uchucchacua polymetallic deposit, Oyon district, Catajambo, Lima Department, Peru, as very rare black metallic subhedral to anhedral crystals, up to 100 μm in length, associated with orpiment, tennantite/tetrahedrite, menchettiite, and other unnamed minerals of the system Pb-Ag-Sb-Mn-As-S, in calcite matrix. Its Vickers hardness (VHN100) is 137 kg/mm2 (range 132–147). In reflected light, oyonite is weakly to moderately bireflectant and weakly pleochroic from dark grey to a dark green. Internal reflections are absent. Reflectance values for the four COM wavelengths (Rmin, Rmax (%) (λ in nm)) are: 33.9, 40.2 (471.1); 32.5, 38.9 (548.3), 31.6, 38.0 (586.6); and 29.8, 36.5 (652.3). Electron microprobe analysis gave (in wt %, average of 5 spot analyses): Cu 0.76 (2), Ag 8.39 (10), Mn 3.02 (7), Pb 24.70 (25), As 9.54 (12), Sb 28.87 (21), S 24.30 (18), total 99.58 (23). On the basis of 20 cations per formula unit, the chemical formula of oyonite is Cu0.38Ag2.48Mn1.75Pb3.79Sb7.55As4.05S24.12. The main diffraction lines are (d in Å, hkl and relative intensity): 3.34 (-312; 40), 3.29 (-520; 100), 2.920 (-132; 40), 2.821 (-232; 70), 2.045 (004; 50). The crystal structure study revealed oyonite to be monoclinic, space group P21/n, with unit-cell parameters a = 19.1806 (18), b = 12.7755 (14), c = 8.1789 (10) Å, β = 90.471 (11)°, V = 2004.1 (4) Å3, Z = 2. The crystal structure was refined to a final R1 = 0.032 for 6272 independent reflections. Oyonite belongs to the Sb-rich members of the andorite homeotypic sub-series within the lillianite homologous series. The name oyonite is after the Oyon district, Lima Department, Peru, the district where the type locality (Uchucchacua mine) is located.

Due to their increased surface area, extent of swelling and active substance loading capacity and flexibility, nanogels made from natural and synthetic polymers have gained significant interest in the scientific and industrial areas. Especially, customized design and implementation of non-toxic, biocompatible, and biodegradable micro/nano carriers makes their usage very feasible for a range of biomedical applications, including drug delivery, tissue engineering, and bioimaging. The design and application methodologies of nanogels have been outlined in this review. Additionally, the most recent advancements in nanogel biomedical applications have been discussed, with a particular emphasis on applications for the delivery of drugs and biomolecules.

Vision-based tactile sensors (VBTS) have become the de facto method of giving robots the ability to obtain tactile feedback from their environment. Unlike other solutions to tactile sensing, VBTS offers high spatial resolution feedback without compromising on instrumentation costs or incurring additional maintenance expenses. However, conventional cameras used in VBTS have a fixed update rate and output redundant data, leading to computational overhead downstream. In this work, we present a neuromorphic vision-based tactile sensor (N-VBTS) that employs observations from an event-based camera for contact angle prediction. Particularly, we design and develop a novel graph neural network, dubbed TactiGraph, that asynchronously operates on graphs constructed from raw N-VBTS streams exploiting their spatiotemporal correlations to perform predictions. Although conventional VBTS uses an internal illumination source, TactiGraph is reported to perform efficiently in both scenarios, with and without an internal illumination source. Rigorous experimental results revealed that TactiGraph achieved a mean absolute error of 0.62∘ in predicting the contact angle and was faster and more efficient than both conventional VBTS and other N-VBTS, with lower instrumentation costs. Specifically, N-VBTS requires only 5.5% of the compute-time needed by VBTS when both are tested on the same scenario.

For disciplines like biological science, security, and the medical field, link prediction is a popular research area. To demonstrate the link prediction many methods have been proposed. Some of them that have been demonstrated through this review paper are TransE, Complex, DistMult, and DensE models. Each model defines link prediction with different perceptions. We argue that the practical performance potential of these methods, having similar parameter values, using the fine-tuning technique to evaluate their reliability and reproducibility of results. We describe those methods and experiments; provide theoretical proofs and experimental examples, demonstrating how current link prediction methods work in such settings. We use the standard evaluation metrics for testing the model's ability.

Zoos are increasingly putting in place formalized animal welfare assessment programs to allow monitoring of welfare over time, as well as to aid in resource prioritization. These programs tend to rely on assessment tools that incorporate resource-based and observational animal- focused measures since it is rarely feasible to obtain measures of physiology in zoo-housed animals. A range of assessment tools are available which commonly have a basis in the Five Domains framework. A comprehensive review of the literature was conducted to bring together recent studies examining welfare assessment methods in zoo animals. A summary of these methods is provided with advantages and limitations of the approach es presented. We then highlight practical considerations with respect to implementation of these tools into practice, for example scoring schemes, weighting of criteria, and innate animal factors for consideration. It is concluded that would be value in standardizing guidelines for development of welfare assessment tools since zoo accreditation bodies rarely prescribe these. There is also a need to develop taxon or species- specific assessment tools to inform welfare management.

Herein we report the expansion of the chemical space available from the chitin, accessible via the biogenic N-platforms 3A5AF, M4A2C and di-HAF. The biologically active heteroaromatics furo[3,2-d]pyrimidin-4-one and furo[3,2-d]pyrimidin-4-amine can be selectively accessed from 3A5AF and M4A2C, respectively. The chiral pool synthon di-HAF is a viable substrate for the Achmatowicz rearrangement, providing streamlined access to 2-aminosugars possessing a versatile hydroxymethyl group at C5.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

Using straightforward and cost-effective methods, persimmon leaves were converted into a high-quality powder. This powder was applied as an adsorbent for the removal of Cu(II) and Cd(II) from aqueous solutions. Scanning electron microscopy (SEM) indicated the presence of particles with non-homogeneous sizes and rough texture. Elemental analysis and the EDX technique confirmed the presence of elements such as sulfur, phosphorus, nitrogen, and oxygen. The results of ¹³C nuclear magnetic resonance (¹³C-NMR), obtained through the cross-polarization technique, suggest the presence of groups containing sulfur and oxygen. Infrared spectroscopy (FTIR) indicated the existence of amine and hydroxyl groups. The material was used in solid-phase extraction of Cu(II) and Cd(II) in batch experiments, and its adsorption capacity was evaluated as a function of time, pH, and analyte concentration. Kinetic equilibrium was reached within 5 minutes, and the experimental data were fitted to the pseudo-second-order kinetic model. The optimum pH for adsorption of both metal species was observed to be around 5.0. The adsorption isotherms were adjusted using the modified Langmuir equation, and the maximum amount of metal species extracted from the solution was determined to be 0.213 mmol g^-1 for Cu(II) and 0.215 mmol g^-1 for Cd(II), with high linear correlation coefficients for both metals. The persimmon leaves are typically abundant during the growing season, and since they are seasonal, the Diospyros kaki L.f. tree undergoes the natural process of leaf abscission, ensuring the availability of leaves for application.

Work in the copper mining industry is often associated with exposure to respirable dust and respirable crystalline silica. This exposure has the potential to cause silicosis, a non-curable occupational respiratory lung disease. This study aimed at establishing the relationship between knowledge, attitudes, work behaviour and practice, compliance with safety standards and exposure to respirable dust. A cross-sectional descriptive survey was conducted on 528 mine workers. Statistical package for social sciences (SPSS) was used for descriptives. Structural Equation Modelling (SEM) with latent variables and partial least-squares (LVPLS) analysis was employed to determine the relationship among these variables. The results indicated that of the four (4) hypotheses, two (2) were supported and two (2) were rejected showing that there is a significant relationship between exposure to respirable dust and work behaviour and practice, as well as compliance with safety standards. Knowledge and attitudes towards respirable dust exposure did not significantly influence exposure. According to the results from the survey, positive work behaviour and practice as well as compliance with safety standards was significantly associated with exposure to respirable dust. It is recommended that the mine should focus on the miners’ work behaviour and practice and compliance with safety standards.

The key objective of the experiment was to show the environmental based of copper nanoparticles which counters the growth of bacterial pathogens such as Pseudomonas aeruginosa, and Staphylococcus aureus. To begin with the experiments, root extract of Asparagus racemosus was used to synthesise Copper nanoparticles. To confirm the formation of Cu-NPs, it was subjected to characterization such as Ultra Violet analysis, X-ray Diffraction method, Fourier Transform Infrared Spectroscopy and Scanning electron microscope images. Later the antibacterial activity of Cu-NPs was studied by incorporating it into two bacterial pathogens (Pseudomonas aeruginosa and Staphylococcus aureus). The outcome displayed a satisfactory antibacterial activity against the bacterial pathogens by the biosynthesized copper nanoparticles. To boost up the enzyme inhibition property of the Cu NPs, Antioxidant and Antidiabetic assay were also performed. The biosynthesised Cu NPs displayed a satisfied result in Antifouling function. The result was used assessed with green algae bloom water.

Carrageenan (car-), used in the pharmaceutical as well as food industry, is marine sulfated polysaccharides. The carrageenan blends (CB) of kappa (κ-), iota (ι-), and lambda (λ-) of 50/50 weight by weight are multipurpose and biocompatible hydrophilic polymers. They were subjected to adsorption of copper (Cu2+) ions. The aim of the study was to conduct extensive rheological and mechanical studies rendering them suitable for biological purposes. The rheology was conducted at various temperatures using a frequency curve, frequency sweep, loss modulus, and storage modulus analysis. Models of rheology like Ostwald, Bingham, and Modified Bingham models were utilized. The rheological results demonstrated non-Newtonian/pseudo-plastic behavior at various temperatures. The models of rheology demonstrated good flow properties and rheological performance of these materials. These materials could be exploited for their application in pharmaceuticals, food, and cosmetics. Thus, our study reflects that these CB can be safely exploited in the healthcare, pharmaceutical, and food industry. However, further studies should be conducted to evaluate their effectiveness in clinical studies.

In the paper, the results of an investigation into trace elements found in slag sulphides from 14 archaeological Bronze Age settlements of the Cis-Urals, Trans-Urals and North and Central Kazakhstan are presented. The study used Cu-(Fe)-sulphides as indicator minerals. Cu-(Fe)-S minerals in slags are primarily represented by covellite and chalcocite, as well as by rarer bornite and single chalcopyrite grains. Slag sulphides formed relic clasts and neogenic droplets of different shapes and sizes. Supergenic ores in the Bronze Age in Urals and Kazakhstan played a significant role in the mineralogical raw material base. In sulphides, the main indicator elements Fe, Co, Ni, As, Se, Te, Sb, Ag, Pb, and Bi are important markers of copper deposit types. Sulphides from olivine Cr-rich spinel containing slags of Ustye, Turganik, and Kuzminkovskoe 2 are characterised by As-Co-Ni assemblages and confined to copper deposits in ultramafic rocks. Olivine sulphide-containing slags from Kamenny Ambar, Konoplyanka and Sarlybay 3 are characterised by Co-Se-Te assemblage and confined to mafic rocks. Glassy sulphide-containing slags from Katzbakh 6, Turganik, Ordynsky Ovrag, Ivanovskoe, Tokskoe, Bulanovskoe 2, Pokrovskoe, Rodnikovoe, and Taldysay are characterised by Ag-Pb-(Ba)-(Bi) assemblage and confined to cupriferous sandstone deposits. High As, Sb, Sn and Ba contents found in slags can be seen as indicators of alloying or flux components in primary copper smelting. These include samples from Ustye, Katzbakh 6, Rodnikovoe, and Taldysay sites, where high Ba and As slag contents are identified. The compilation of a database with a broad sample of sulphide compositions from Bronze Age slags and mines in the Urals and Kazakhstan will permit the further identification of ore types and raw materials associated with a particular deposit.

The neurodegenerative diseases (Alzheimers, Parkinsons, amyotrophic lateral sclerosis, Huntingdons) and the prion disorders, have in common a dysregulation of metalloprotein chemistry involving redox metals (Cu,Fe,Mn). The consequent oxidative stress gives rise to protein plaques and neuronal cell death. An equilibrium exists between the functional requirement of the brain for Cu and Fe and their destructive potential with the production of reactive oxygen species. The importance of the brain barrier is highlighted in regulating the import of these metals. Upregulation of key transporters occurs in foetal and neonatal life when brain metal requirement is high and is down-regulated in adult life when need is minimal. By contrast a neonatal mode of CTR1 upregulation persists in feral N.Ronaldsay sheep. This has led to the premise that metal regulation may return to the default setting in ageing with implications for neurodegenerative disease.

Gymnema sylvestre is a pharmacological plant which has a rich source of bioactive compounds specifically gymnemic acid (GA) and phenolic compounds (PC) that used for pharmaceutical industries. Sources for naturally occurring bioactive compounds are limited, due to geographical and seasonal variations; on the other hand, it is commercially in demand. Biosynthesis of G. sylvestre phytochemicals through in vitro culture often enhanced by elicitation. The use of cell suspension cultures (CSC) has interested serious attention on the production of essential phytochemicals. The current study is aimed at improving the contents of GA and PC in G. sylvestre CSC using the copper oxide nanoparticles (CuO NPs). Callus was obtained on MS medium with 2.0 mg/L 2,4-dichlorophenoxyacetic acid (2,4-D), 0.1 mg/L kinetin (KIN), phytoagar (8.0 g/L), and sucrose (30 g/L). The above medium devoid of agar was used for the initiation of CSC. The CSC was treated with three levels of CuO NPs (1, 3 or 5 mg/L) to enhance the production of GA and PC. The greatest amount of GA (89.25 mg/g dry cell mass, DCM), total phenolic (245.10 mg/g), and flavonoid (4.57 mg/g) in CSC were achieved when G. sylvestre cells were treated for 48 h with 3 mg/L CuO NPs. Also, the biomedical potential (antioxidant, antidiabetic, anti-inflammatory, antibacterial, antifungal and anticancer activities) were also high in the CuO NPs (3 mg/L) treated CSC extracts of G. sylvestre. CuO NPs elicitation of CSC significantly increased production of GA (9-fold), and PC than non-elicited CSC in G. sylvestre.

Micronutrient deficiencies are a major public health problem. Beans are an important plant-based source of iron, zinc and copper, but their absorption is reduced in the presence of anti-nutrients such as phytates, polyphenols and tannins. Soaking and discarding the soaking water before cooking is unanimously recommended, but this can result in mineral loss. Data on the consequences for mineral bioaccessibility is still limited. This study aimed to evaluate iron, zinc and copper bioaccessibility in black beans cooked (regular pan, pressure cooker) with and without the soaking water. Minerals were quantified by ICP-MS, myo-inositol phosphates (InsP₅, InsP₆) by HPLC ion-pair chromatography, total polyphenols using Folin-Denis reagent and condensed tannins using Vanillin assay. Mineral bioaccessibility was determined by in vitro digestion and dialysis. All treatments resulted in a statistically significant reduction of total polyphenols (30%) and condensed tannins (20%). Only when discarding the soaking water a loss of iron (6%) and copper (30%) was observed, and InsP₆ was slightly decreased (7%) in one treatment. Bioaccessibility of iron and zinc were low (about 0.2% iron and 35% zinc), but copper presented high bioaccessibility (about 70%). Cooking beans under pressure without discarding the soaking water resulted in the highest bioaccessibility levels among all household procedures. Discarding the soaking water before cooking did not improve the nutritional quality of the beans.

With the increasing of copper consumption, the in-use stock of copper tends to increase. This paper used the “average use life method” to quantify the amount of copper in-use stock, and calculated the average age of in-use stock. It was indicated that the total in-use stock had an overall smooth trends, and reached its peak in 2007 was about 68.9 Mt (million tons), in addition, in-use stock per capita reached its peak ,234 kg/capita in 2001. The results demonstrated that during the period 1992-2002, the average age of copper in-use stock was continually decreased, but gradually increased since the year 2003. The fixed assets depreciation method used in this paper is applied to analyze depreciated copper in-use stock, and to analyze the relationship with economic indicator (GDP). It is demonstrated that it was inconsistent with the theory of Environmental Kuznets Curve (EKC) before 2000, this might be the demand for copper in the service sector is greater than the reduced strength of alternatives. Finally, scenario analysis of future copper in-use stock and depreciated copper in-use stock per capita in the U.S. were presented. The corresponding average age of the in-use stock will have a slight rise in the next decade.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

The aim of this study was to investigate the impact of Process Oriented Guided Inquiry Learning (POGIL)-based instruction versus lecture-based instruction on Grade 12 students’ performance in circular motion unit. A quasi-experimental, pretest-posttest design, the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes: Knowing, Applying and Reasoning (KAR). The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys) and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a unit of circular motion in physics using POGIL-based instruction while the control group was taught the unit using lecture-based instruction. The findings of the study showed statistically significant differences between students of the control group and the treatment group in favor of the later regarding their circular motion performance, suggesting the superiority of the POGIL in enhancing student understanding of the circular motion.

This article investigates the prospect of implementing multidisciplinary and multicultural student teamwork (MMT) involving Case-based Learning (CBL) and Problem-based Learning (PBL) as a sustainable teaching practice. Based on a mixed methods approach, which includes direct observation (both physical and virtual), questionnaire distribution and focus-group interviews the study reveals that MMT through CBL and PBL can both facilitate and hinder sustainable learning. Our findings show that while MMT enhances knowledge sharing, it also poses a wide range of challenges, raising questions about its social significance as a sustainable teaching practice. The study suggests the implementation of certain mechanisms, such as ‘Teamwork Training’ and ‘Pedagogical Mentors’, aiming to strengthen the sustainable orientation of MMT through CBL and PBL.

In MBSE there is yet no converged terminology. The term ’system model’ is used in different contexts in literature. In this study we elaborated the definitions and usages of the term ’system model’, to find a common definition. 104 publications have been analyzed in depth for their usage and definition as well as their meta-data e.g., the publication year and publication background to find some common patterns. While the term is gaining more interest in recent years it is used in a broad range of contexts for both analytical and synthetic use cases. Based on this three categories of system models have been defined and integrated into a more precise definition.

This article discusses the use of game design as a method for interdisciplinary project-based teaching in secondary school education to convey informatics and society topics. There is a lot of knowledge about learning games but little background on project-based teaching using game design as a method. We present the results of an analysis of student-created games and an evaluation of a student-authored database on learning contents found in commercial off-the-shelf games. We further contextualise these findings using a group discussion with teachers. Results underline the effectiveness of project-based teaching to raise awareness for informatics and society topics. We further outline informatics and society topics that are particularly interesting to students, genre preferences and potentially engaging game mechanics stemming from our analyses.

The ubiquity of mobile sensors (such as GPS, accelerometer and gyroscope) together with increasing computational power have enabled an easier access to contextual information, which proved its value in next generation of the recommender applications. The importance of contextual information has been recognized by researchers in many disciplines, such as ubiquitous and mobile computing, to filter the query results and provide recommendations based on different user status. A context-aware recommendation system (CoARS) provides a personalized service to each individual user, driven by his or her particular needs and interests at any location and anytime. Therefore, a contextual recommendation system changes in real time as a user’s circumstances changes. CoARS is one of the major applications that has been refined over the years due to the evolving geospatial techniques and big data management practices. In this paper, a CoARS is designed and implemented to combine the context information from smartphones’ sensors and user preferences to improve efficiency and usability of the recommendation. The proposed approach combines user’s context information (such as location, time, and transportation mode), personalized preferences (using individuals past behavior), and item-based recommendations (such as item’s ranking and type) to personally filter the item list. The context-aware methodology is based on preprocessing and filtering of raw data, context extraction and context reasoning. This study examined the application of such a system in recommending a suitable restaurant using both web-based and android platforms. The implemented system uses CoARS techniques to provide beneficial and accurate recommendations to the users. The capabilities of the system is evaluated successfully with recommendation experiment and usability test.

Hospital-based programs democratize mRNA therapeutics by facilitating the processes to translate a novel RNA idea from the bench to the clinic. Because mRNA is essentially biological software, therapeutic RNA constructs can be rapidly developed. The generation of small batches of clinical grade mRNA to support IND applications and first-in-man clinical trials, as well as personalized mRNA therapeutics delivered at the point-of-care, is feasible at a modest scale of cGMP manufacturing. Advances in mRNA manufacturing science and innovations in mRNA biology, are increasing the scope of mRNA clinical applications.

Drug discovery utilizes high-throughput screening (HTS) methods applying target and cell-based assays. This review discusses the challenges and benefits associated with these assays in HTS. Discussed the strategies that can be applied for the development of screening assays through primary and secondary screens for target identification. Further discussion on identify-ing the most efficacious drugs following these approaches in cancer. Even though various drugs have been identified to treat cancer, there is high demand of more relevant phenotypic assays to produce desired diseased phenotype to only highlighting the specific targets instead of off-targets. Hopefully, the new developing strategies could provide innovative drugs to treat cancer patients to reduce mortality rate.

The correlations of seismic noise, recorded during 1997-2022 at 229 stations around the world are investigated. The property of waveforms, known as the Donoho-Johnston threshold, is analyzed, which separates the absolute values of the orthogonal wavelet coefficients into "small" and "large". Network of 50 reference points is considered. For each reference point, a time series with a time step of 1 day is calculated as the median of the values of the DJ index from the 5 nearest stations. For each reference point, the correlations between the values of the DJ index at other reference points are calculated in a sliding time window of 365 days. Average values of the DJ index decrease, which is interpreted as indicators of global seismic hazard increasing. The maximum distances between reference points with strong correlations show an explosive increase after 2011. Bursts in the mean coherences between the length of day (LOD) and the values of the DJ index at the reference points precede the release of seismic energy with a delay of about 530 days. High amplitude of the DJ index response to LOD for the times 2020-2022 was identified, which may forecast a strong earthquake in the second half of 2023.

Noise in requirements has been known to be a defect in software requirements specifications (SRS). Detecting defects at an early stage is crucial in the process of software development. Noise can be in the form of irrelevant requirements that are included within a SRS. A previous study had attempted to detect noise in SRS, in which noise was considered as an outlier. However, the resulting method only demonstrated a moderate reliability due to the overshadowing of unique actor words by unique action words in the topic-word distribution. In this study, we propose a framework to identify irrelevant requirements based on the MultiPhiLDA method. The proposed framework distinguishes the topic-word distribution of actor words and action words as two separate topic-word distributions with two multinomial probability functions. Weights are used to maintain a proportional contribution of actor and action words. We also explore the use of two outlier detection methods, namely Percentile-based Outlier Detection (PBOD) and Angle-based Outlier Detection (ABOD), to distinguish irrelevant requirements from relevant requirements. The experimental results show that the proposed framework was able to exhibit better performance than previous methods. Furthermore, the use of the combination of ABOD as the outlier detection method and topic coherence as the estimation approach to determine the optimal number of topics and iterations in the proposed framework outperformed the other combinations and obtained sensitivity, specificity, F1-score, and G-mean values of 0.59, 0.65, 0.62, and 0.62, respectively.

Animal-based measures are the measure of choice in animal welfare assessment protocols as they can often be applied completely independently to the housing or production system employed. Although there has been a small body of work on potential animal-based measures for farmed crocodilians [1-3], they have not been studied in the context of an animal welfare assessment protocol. Potential animal-based measures, that could be used to reflect the welfare state of farmed crocodilians, were identified and aligned with the Welfare Quality® principles of good housing, good health, good feeding and appropriate behaviour. A consultation process with a panel of experts was used to evaluate and score the potential measures in terms of validity and feasibility. This resulted in a toolbox of measures being identified for further development and integration into animal welfare assessment on the farm. Animal-based measures related to ‘good feeding’ and ‘good health’ received the highest scores for validity and feasibility by the experts. There was less agreement on the animal-based measures that could be used to reflect ‘appropriate behaviour’. Where no animal-based measures were deemed to reliably reflect a welfare criterion nor be useful as a measure on the farm, additional measures of resources or management were suggested as alternatives. Future work in this area should focus on the reliability of the proposed measures and involve further evaluation of their validity and feasibility as they relate to different species of crocodilian and farming system.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

The exploitation of lipid membranes in biosensors has provided the ability to reconstitute a considerable part of their functionality to detect trace of food toxicants and environmental pollutants. Nanotechnology enabled sensor miniaturization and extended the range of biological moieties that could be immobilized within a lipid bilayer device. This chapter reviews recent progress in biosensor technologies based on lipid membranes suitable for environmental applications and food quality monitoring. Numerous biosensing applications are presented, putting emphasis on novel systems, new sensing techniques and nanotechnology-based transduction schemes. The range of analytes that can be currently detected include, insecticides, pesticides, herbicides, metals, toxins, antibiotics, microorganisms, hormones, dioxins, etc. Technology limitations and future prospects are discussed, focused on the evaluation/ validation and eventually commercialization of the proposed sensors.

Given the increase in consumers’ preferences for coffee, it is becoming important to understand their decision-making processes in the coffee chain context. To deepen the understanding of sustainable outcomes in this context, this study investigates the role of dedication- and constraint-based mechanisms in forming consumers’ repurchase and positive word-of-mouth (WOM) intentions, two critical sustainable outcomes. We examined the effects of coffee quality, the quality of the physical environment, and service quality in accelerating the formation of dedication-based factors. Moreover, this study offers an in-depth understanding of the enablers of perceived switching costs. Data collected from 238 university students that frequently visit coffee chains are empirically tested against the proposed theoretical framework by using structural equation modeling. The results confirm that both dedication- and constraint-based factors substantially predict consumers’ sustainable outcomes in the coffee chain context. Brand image and perceived switching costs play an important role in enhancing consumers’ repurchase and positive WOM intentions compared with customer satisfaction. Coffee quality is significantly associated with both customer satisfaction and brand image, whereas the quality of the physical environment and service quality are only significantly associated with brand image. Habit is found to be the key enabler of perceived switching costs, while loyalty programs have no significant impact on perceived switching costs.

Effectively mapping and monitoring rubber plantation is still changing. Previous studies have explored the potential of phenology features for rubber plantation mapping through a pixel-based approach (pixel-based phenology approach). However, in fragmented mountainous Xishuangbanna, it could lead to noises and low accuracy of resultant maps. In this study, we investigated the capability of an integrated approach by combining phenology information with an object-based approach (object-based phenology approach) to map rubber plantations in Xishuangbanna. Moderate Resolution Imaging Spectroradiometer (MODIS) data were firstly used to acquire the temporal profile and phenological features of rubber plantations and natural forests, which delineates the time windows of defoliation and foliation phases. Landsat images were then used to extract a phenology algorithm comparing three different approaches: pixel-based phenology, object-based phenology, and extended object-based phenology to separate rubber plantations and natural forests. The results showed that the two object-based approaches achieved higher accuracy than the pixel-based approach, having overall accuracies of 96.4%, 97.4%, and 95.5%, respectively. This study proved the reliability of a phenology-based rubber mapping in fragmented landscapes with a distinct dry/cool season using Landsat images. This study indicated that the object-based phenology approaches can effectively improve the accuracy of the resultant maps in fragmented landscapes.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Traditional Filuferru is an ancient spirit from Sardinia, Italy, usually obtained from the distillation of wine or grape marc. In this contribution, the results of the first chemical characterization of a wide number of craft Filuferru samples has been accomplished in terms of evaluation of the alcoholic strength, qualitative and quantitative GC-MS analysis of the volatile composition of the distillate, and its trace element composition by means a ICP-MS method. Both instrumental methods have been validated and applied on 21 craft samples of Filuferru, whereas one sample of commercial distillate has been analyzed for comparison purposes. Alcoholic strength ranged between 41.0 and 62.4% (v/v). Sixty volatile compounds were identified and ten of them have been quantified. Analogies and differences with Grappa (i.e. the Italian distilled spirit most close to Filuferru) have been highlighted in the qualitative and quantitative profile of this matrix. Often meaningful amounts of acetaldehyde, ethyl acetate, dietyl acetal and acetic acid were measured. Elemental analysis, performed on toxic, non-toxic elements and oligoelements, 18 in total, revealed a wide variability of concentrations in both analytes and samples. High concentrations of Cu are sometimes evidenced, likely caused by losses from the distillation apparatus. The principal components analysis (PCA) allowed the differentiation of the ten volatile compounds quantified in two groups: the former, described mainly by PC1, constituted by acetic acid, ethyl acetate, dietyl acetal and acetaldehyde, and the second, described by PC2, constituted by 1-propanol, 2-methyl-1-propanol, the two coeluiting isomers 2-methyl-1-butanol and 3-methyl-1-butanol,1-hexanol, 2-phenylethanol and 2,3-butanediol. Data obtained may be useful in order to establish a regulation for the production of high-quality traditional Filuferru from Sardinia.

Saudi Arabia is an oil-reliant nation as a large percentage of its GDP comes from oil resources. Oil dependency leaves a county at the mercy of the international crude market, and a decrease in the price of crude can seriously destabilize the economy of such nations. An example is the case of Venezuela whose dependence on oil caused a national disaster (McCarthy, 2017). As such, the nation’s exports, GDP, and government revenue are primarily dependent on oil revenue, and the recent decrease in the oil prices has decreased Venezuela’s national revenue resulting in economic collapse as well as inflation. A shift from a resource based economy to a knowledge based economy will help Saudi Arabia become less reliant on its oil revenues for its economic stability and growth (Nurunnabi, 2017).

This study focuses on enhancing controllable fibrin-based hydrogels for tissue engineering, addressing existing weaknesses. By integrating a novel copolymer, we improve the foundation for cell-based angiogenesis with adaptable structural features. Tissue engineering often faces challenges like waste disposal and nutrient supply beyond the 200 µm diffusion limit. Angiogenesis breaks through this limitation, allowing the construction of larger constructs. Our innovative scaffold combination significantly boosts angiogenesis, resulting in longer branches and more capillary network junctions. The copolymer attached to fibrin fibers enables precise adjustment of hydrogel mechanical-dynamic properties for specific applications. Our material proves effective for angiogenesis, even under suppression factors like suramin. In our study, we prepared fibrin-based hydrogels with and without the copolymer PVP12400-co-GMA10mol%. Using a co-culture system of human umbilical vein endothelial cells (HUVEC) and mesenchymal stem cells (MSC), we analyzed angiogenetic behavior on and within the modified hydrogels. Capillary-like structures were reproducibly formed on different surfaces, demonstrating the general feasibility of three-dimensional endothelial cell networks in fibrin-based hydrogels. This highlights the biomaterial's suitability for in vitro pre-vascularization of biohybrid implants.

In this study, graphite, the most stable form of carbon, was examined for its hexagonal crystalline structure with specific dimensions (ao=2.46 Ǻ; co=6.70 Ǻ). Its framework comprises parallel carbon atom planes forming regular hexagons (side length 1.415 Ǻ) and 120° angles between adjacent atoms. Two structural variations exist: hexagonal symmetry (1-2-1-2-1-2 planes) and rhomboidal symmetry (1-2-3-1-2-3 planes). The research aimed to produce high-density graphite utilizing carbonaceous raw materials. Graphite-based materials often exhibit high porosity, necessitating additional treatments. The study successfully obtained mesophase tar pitch (yield: 45%), a pivotal raw material, and high-density graphite. The resulting graphite underwent characterization for physical properties (apparent and real density, porosity and compression strength), demonstrating conformity with existing literature data.

After the great success of Mobile wallet, the Internet of Things (IoT) leaves the door wide open for consumers to use their connected devices to access their bank accounts and perform routine banking activities from anywhere, anytime and with any device. However, consumers need to feel safe when interacting with IoT-based payment systems, and their personal information should be protected as much as possible. Unlike as usually done in the literature, in this paper, we introduce two lightweight and secure IoT-based payment protocols based on an identity-based signature scheme. We adopt a server-aided verification technique to construct the first scheme. This technique allows to outsource the heavy computation overhead on the sensor node to a cloud server while maintaining the user's privacy. The second scheme is built upon a pairing-free ECC-based security protocol to avoid the heavy computational complexity of bilinear pairing operations. The security reduction results of both schemes are held in the Random Oracle Model (ROM) under the discrete logarithm and computational Diffie-Hellman assumptions. Finally, we experimentally compare the proposed schemes against each other and against the original scheme on the most commonly used IoT devices: a smartphone, a smartwatch and the embedded device Raspberry Pi. Compared with existing schemes, our proposed schemes achieve significant efficiency in the term of communication and computational overheads

The complexity of modern power grids, exacerbated by integrating diverse energy sources, espe-cially inverter-based resources (IBRs), presents a significant challenge to grid operation and plan-ning since linear models fail to capture the intricate IBR dynamics. This study employs the Sparse Identification of Nonlinear Dynamics (SINDy) method to bridge the gap between theoretical un-derstanding and practical implementation in power system analysis. It introduces the novel Volterra-based Nonlinearity Index (VNI) to examine system-level nonlinearity comprehensively. The distinction of dynamics into first-order linearizable terms, second-order nonlinear dynamics, and third-order noise elucidates the intricacy of power systems. The findings demonstrate a fundamental shift in system dynamics as power sources transit to IBRs, revealing system-level nonlinearity compared to module-level nonlinearity in conventional syn-chronous generators. The VNI quantifies nonlinear-to-linear relationships, enriching our comprehension of power system behavior and offering a versatile tool for distinguishing between different nonlinearities and visualizing their distinct patterns through the proposed VIN profile.

This study explores cutting-edge and sustainable green methodologies and technologies for the synthesis of functional nanomaterials, with a specific focus on the removal of water contami-nants and the application of kinetic adsorption models. Our research adopts a conscientious ap-proach to environmental stewardship by synergistically employing eco-friendly silver nanopar-ticles, synthesized using Justicia Spicigera extract as a biogenic reducing agent, in conjunction with Mexican zeolite to enhance contaminant remediation, particularly targeting Cu²⁺ ions. Structural analysis, utilizing X-ray diffraction (XRD) and high-resolution scanning and transmis-sion electron microscopy (TEM and SEM), yields crucial insights into nanocomposite structure and morphology. Rigorous linear and non-linear kinetic models, encompassing pseudo-first order, pseudo-second order, Freundlich, and Langmuir, are employed to elucidate the kinetics and equilibrium behaviors of adsorption. Results underscore the remarkable efficiency of the Zeolite-Ag composite in Cu²⁺ ion removal, surpassing traditional materials, achieving an im-pressive adsorption rate of 98% for Cu. Furthermore, the Zeolite-Ag composite exhibits maxi-mum adsorption times of 480 minutes. In the computational analysis, an initial mechanism for Cu²⁺ adsorption on zeolites is identified. The process involves rapid adsorption onto the surface of the Zeolite-Ag NP composite, followed by a gradual diffusion of ions into the cavities within the zeolite structure. Upon reaching equilibrium, a substantial reduction in copper ion concen-tration in the solution signifies successful removal. This research represents a noteworthy stride in sustainable contaminant removal, aligning with eco-friendly practices and supporting the potential integration of this technology into environmental applications. Consequently, it pre-sents a promising solution for eco-conscious contaminant remediation, emphasizing the utiliza-tion of green methodologies and sustainable technologies in the development of functional na-nomaterials

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

Compelling epidemiologic data support the critical role of dietary fructose in the epidemic of obesity, metabolic syndrome and nonalcoholic fatty liver disease (NAFLD). The metabolic effects of fructose on the development of metabolic syndrome and NAFLD are not completely understood. High fructose intake impairs copper status, and copper-fructose interactions have been well documented in rats. Altered copper-fructose metabolism leads to exacerbated experimental metabolic syndrome and NAFLD. A growing body of evidence has demonstrated that copper levels are low in NAFLD patients. Moreover, hepatic and serum copper levels are inversely correlated with the severity of NAFLD. Thus, high fructose consumption and low copper availability are considered two important risk factors in NAFLD. However, the causal effect of copper-fructose interactions as well as the effects of fructose intake on copper status remain to be evaluated in humans. The aim of this review is to summarize the role of copper-fructose interactions in the pathogenesis of the metabolic syndrome and discuss the potential underlying mechanisms. This review will shed light on the role of copper homeostasis and high fructose intake and point to copper-fructose interactions as novel mechanisms in the fructose induced NAFLD.

This work aims to explore the impact of side loads, drill-pipe tool-joint (DP-TJ) speed (RPM), and mud type on the austenitic stainless steel SM2535-110 casing wear characteristics. Actual field drill pipe tool joints, casings, and drilling muds are used in this study. The results of the study show that under both types of lubrication, the wear volume increased with radial load and DP-TJ speed. SM2535-110 casing specimens tested under oil-based mud (OBM) lubrication had higher casing wear volumes than those obtained under water-based mud (WBM) lubrication. This unexpected behavior is mainly due to the increase in the surface hardness of the casing specimens tested under WBM. The results also show that the specific wear factor (K) values of specimens tested under WBM are in general 2 to 4 times higher than those obtained under OBM. While K values under WBM increase with both the side load and RPM, those under OBM show a sharp decrease with RPM. This behavior under OBM is due to this lubricant’s higher viscosity and the change of lubrication regime from thin film to thick film lubrication at higher RPM. Scanning electron microscopy (SEM) and the digital microscopic imaging (DMI) of SM235-110 casing specimens show that an aggressive combination of adhesive, abrasive, and plastic deformation was observed under WBM, while the dominant wear mechanism under OBM is abrasive wear.

Financial markets require a great deal of decision making from the investors and market makers. One metric that can help ease the process of decision making is investment risk which can be measured in two parts; systematic risk and idiosyncratic risk. Clear understanding of the volatilities in each risk component can be a powerful signal in recognizing the right assets to maximize the investment returns. In this paper, we focus on the idiosyncratic volatility values and pre-calculate the idiosyncratic volatility values for 31,198 members of NYSE, Amex and Nasdaq markets for the trades occurring between January 1963 and December 2019. Utilizing a subset of dataset, limited to Nasdaq100 index, we consider the application of machine learning techniques in predicting the idiosyncratic volatility values using the raw trade data to explore a data extension option for the future market trade records that have not yet occurred. We offer a deep learning based regression model and compare it with traditional tree-based methods on a small subset of our per-calculated idiosyncratic volatility dataset. Our analytical results show that the performance of the deep learning techniques is much more robust in comparison to that of the traditional tree-based baselines.

This study compares the effects of lecture-based instruction and process-oriented guided inquiry learning (POGIL)-based instruction on the self-efficacy performance of Grade 12 students. A quasi-experimental, pretest-posttest design was adopted to investigate and assess the impact of POGIL-based instruction versus lecture-based instruction on students’ performance as measured by three types of cognitive outcomes; Knowing, Applying and Reasoning (KAR). Two government high schools in Alain were selected as research sites, one for the boys and one for the girls. The total number of participants was approximately 110 students (N=110); 54 were assigned to treatment groups (25 girls and 29 boys), and 56 were assigned to control groups (27 girls and 29 boys). The treatment group was taught a circular motion unit in physics using POGIL-based instruction, while the control group was taught the unit using lecture-based instruction. The study's findings showed statistically significant differences between students of the control group and the treatment group in favour of the latter regarding their science performance, self-efficacy and science-related attitudes. Moreover, positive correlations were found between participants’ performance at the KAR test, self-efficacy and scientific attitudes towards scientific inquiry after the intervention. In conclusion, it is recommended to shift teaching towards POGIL-based instruction due to its positive impact on students’ performance and self-efficacy. It is also suggested to replicate the study to include government and private schools, elementary and high schools, teachers and advisors.

Background: Endometriosis is a female chronic inflammatory disease in which endometrial tissue develops outside the uterine cavity. It is a complex pathology, that significantly contributes to morbidity in premenopausal women, leading to chronic pain, infertility, and subfertility negatively impacting the physical, and emotional well-being and overall quality of life. The public health burden of endometriosis remains elusive and challenging to determine, and this uncertainty can lead to inadequate healthcare services and treatments. Objective: To estimate the incidence and prevalence of endometriosis in Italy using the hospital discharge records database. Population-based retrospective study. Nationwide between 2011 and 2020. Methods: From the National Hospital Discharge Database were selected all admissions with a diagnosis of endometriosis (ICD-9-CM, codes 617.x), supported by the presence of a procedure code of laparoscopy or any other surgical procedure allowing direct visualisation of the lesions. Main outcomes measures Incidence and prevalence of endometriosis were estimated for the entire 2010-2020 period and by individual year, analysing the time trend and variability in different geographical areas of Italy. Results: A total of 134,667,646 women aged 15–50 years with one or more hospitalisations for endometriosis in all Italian hospitals. The incidence of endometriosis in Italy during this period was 0.839 per 1000 women (CI95% 0.834-0.844), exhibiting a statistically significant decreasing trend over the years. A discernible north-south gradient was observed, with higher rates documented in the northern regions. The prevalence rate stood at 14.0 per 1000 during the same period, and a similar north-south geographical gradient was identifiable in the prevalence rates as well. Conclusions: The utilization of national-level hospital data enables the generation of incidence and prevalence data for endometriosis without variations in methods and definitions, facilitating the evaluation of temporal trends and regional comparisons. Understanding and quantifying this phenomenon is essential for appropriate healthcare planning in various Italian regions.

The potential advantages of plant-based interventions in decreasing the incidence and lessening the morbidity and mortality of COVID-19 are yet to be widely acknowledged. Nevertheless, recent publications propose that these interventions could be effective. Our cardiology center conducted an interventional study in which we incorporated plant-based foods and provided supplementation to 3470 elderly COVID-19 patients with multiple comorbidities. We pay close attention to the precise selection of food items, the application of appropriate processing methods, and the provision of nourishing meals to our patients. Our outcome was highly successful as we achieved a zero mortality rate, and none of our patients experienced worsening conditions or required hospitalization. In this review article we present the mechanisms how plant-based and supplement interventions can mitigate COVID-19 disease severity and mortality. And experts have validated our hypotheses very recently. The measures and methods used to address the ongoing SARS-CoV-2 pandemic through plant-based interventions and supplements are effective and may help prevent or manage future pandemics.

Abstract: This study aims to evaluate the effectiveness of plant-based diets and supplement interventions in mitigating the severity and mortality of COVID-19 patients. Observational research suggests that a diet high in plant-based foods may decrease the likelihood and severity of SARS-CoV-2 infection. However, several studies have faced criticism regarding the accuracy of obtaining dietary questionnaires and the insufficient intake of essential vitamins and minerals in such diets. To address these issues, this study employed a prospective interventional design that strictly controlled the quality, quantity, and processing of plant-based foods provided. Furthermore, the study incorporated supplementation, which enhanced the anti-viral, anti-inflammatory, antioxidant, antithrombotic, and immunomodulatory properties of a plant-based diet against the SARS-CoV-2 virus. Of the 3,470 COVID-19 elderly patients, half already followed a plant-based diet, and the other half new patients, both with various comorbidities, were intervened with a plant-based diet and supplementation. The results showed that the participants in the non-plant-based diet group were twice as likely to have experienced moderate disease (with 95% confidence limit: 1.42-3.12) and 2.4 times more likely to have experienced severe disease (with 95% confidence limit: 1.2-5.0) with a significant p-value of less than 0.0005 and 0.016 respectively, compared to those in the PBD group. During the interventions, none of the participants experienced disease progression or hospitalization, and there were no reported deaths by the end of the study. The outcome was highly favorable and aligned with the researchers' expectations, as COVID-19 morbidity and mortality rates in Indonesia were among the highest in Asia. This research may provide significant insights into the prevention and management of COVID-19 and aid in better preparation for future pandemics.

Chitosan is a copolymer of β-glucosamine and N-acetylglucosamine. Recent experiments showed that the degree and pattern of acetylation along the chitosan chain modulate the biological and physicochemical properties; however, the molecular mechanism is unknown. Here we apply the de novo all-atom molecular dynamics (MD) simulations to study chitosan’s self-assembly process at different degrees of acetylation and two different acetylation patterns. The simulations revealed that the 10-mer chitosan chains with 50% acetylation in either block or alternating patterns associate to form ordered nanofibrils comprised of mainly antiparallel chains in agreement with the fiber diffraction data of deacetylated chitosan. Surprisingly, regardless of the acetylation pattern, the same intermolecular hydrogen bonds mediate the fibril sheet formation while water-mediated interactions stabilize the sheet-sheet stacking. Moreover, the acetylated units are involved in forming the strong intermolecular hydrogen bonds (NH–O6 and O6H–O7), which offers an explanation for the experimental observation that increased acetylation lowers chitosan’s solubility. Taken together, the present study provides the atomic-level understanding the role of acetylation plays in modulating chitosan’s physiochemical properties, contributing to the rational design of chitosan-based materials with the ability to tune by its degree and pattern of acetylation. Additionally, we disseminate the improved molecular mechanics parameters that can be applied in MD studies to further understand chitosan-based materials.

The process of Targeted Opinion Word Extraction (TOWE), a critical component of aspect-based sentiment analysis (ABSA), revolves around identifying opinionated words linked to specific aspect-terms within sentences. Existing deep learning approaches, while effective, often overlook the syntactic structure of sentences, a factor that previous studies have identified as beneficial for TOWE. In this study, we introduce the Syntactic-Enhanced Deep Learning Model (SEDLM) that integrates syntactic structures into deep learning frameworks for TOWE. Our approach leverages syntax-driven opinion potential scores and syntactic inter-word connections, enhancing model performance. Additionally, we introduce an innovative regularization strategy aimed at distinguishing word representations in TOWE tasks. Our comprehensive analysis reveals that SEDLM sets new benchmarks in performance across multiple standard datasets.

The implementation of Boolean functions using Nano crossbar- based switching lattices has been suggested as a substitute for conventional CMOS-based approaches in digital circuits . This alternative may satisfy the needs of future electronic designs, con- sidering the expected end of Moore’s law. This study introduces CVM, a Crossbar-based circuit Verification through Modeling tech- nique

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

As formally is known, nanozymes are the nanomaterials or nanoscale materials which reveal enzyme-like properties. These nanomaterilas can be utilzied instead of the natural enzymes for simulation of enzymatic reactions in harsh environmental conditions. Among different nanoscale enzyme-like materials, the majority of them reveal peroxidase-like activity, due to the high catalytic efficiency and stability of peroxidase-like nanozymes, they had been widely utilized for sensing and detection via constructing the colorimetric and fluorescence-based analytical and bioanalytical sensors. There are several high impact nanozymatic sensors which reported in the literature. Although the review articles published in this field, however, the current reviews focus on the introducing nanozyme field not description on the best articles published in this filed. Hence, this article aimed to present a brief introduction on the nanozyme-based chemistry with emphasizing on the historical overview of recent nanozymatic sensors. In this regard the best nanozymatic sensors which published over 2016-2023 were briefly described and overviewed.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

In this work, the inhibition properties of new bio-based lignine ILs on the corrosion of mild steel in an aqueous solution of 0.01 M NaCl were investigated by Potentiostatic Electrochemical Impedance Spectroscopy (PEIS), Cyclic Potentiodynamic Polarization (CPP). Moreover, the surface was characterized using SEM, EDS, and optical profilometry. The influence of cation and anion on the inhibitor properties and a possible synergistic effect were investigated. The IL choline syringate showed a promising performance, reducing the corrosion current after 24-hour immersion in 0.01 M sodium chloride, from 1.66 µA/cm2 for the control to 0.066 µA/cm2 with 10 mM of the IL present. In addition to the performance as a corrosion inhibitor, both components of this IL also meet or exceed current additional desired properties of such compounds, being readily available, economically efficient, and well tolerated in organisms and the environment.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

Abstract: Calcium-based catalysts are of a high interest for glycerol polymerization due to their high catalytic activity and large availability. However, their poor stability under reaction conditions is an issue. In the present study, we investigated the stability and catalytic activity of Ca-hydroxyapatites (HAps) as one of the most abundant Ca-source in nature. A stochiometric, a Ca-deficient and a Ca-rich HAps have been synthetized and tested as catalysts in the glycerol polymerization reaction. Deficient and stochiometric HAps exhibited a remarkable 100% selectivity to triglycerol at 15 % of glycerol conversion at 245 °C after 8 h of reaction in the presence 0.5 mol.% of catalyst. Moreover, under the same reaction conditions, Ca-rich HAp showed a high selectivity (88 %) to di- and triglycerol at a glycerol conversion of 27 %. Most importantly, these catalysts were unexpectedly stable towards leaching under the reaction conditions based on the ICP-OES results. However, based on the catalytic tests and characterization analysis performed by XRD, XPS, IR, TGA-DSC and ICP-OES, we found that HAps can be deactivated by the presence of the reaction products themselves, i.e., water and polymers.

A project-based module on Sustainable Development Goal number 5, Gender Equality, was im-plemented on 5 different groups of Business English students consisting of a total number of 62 students in higher education. The main purpose of this project was to raise awareness of this goal by means of a flipped method in which students were required to carry out some research on specific areas of the aforementioned goal and work in teams to elaborate oral presentations. Once their findings were shared in class, students were expected to answer a written questionnaire of open-ended questions which were part of a qualitative analysis. Results of this survey showed that not only 90% of the students gained in depth knowledge of this goal, but also 85% had built a positive attitude to take initiative and 80% were optimistic about future gender equality. Finally, 70% of students suggested further social action to curb the problem of gender discrimination. On the whole, the flipped classroom method of learning combined with project-based group work have proven to be an effective way to raise awareness of this goal, create a more positive attitude, in-crease their willingness to take action as well as widening their English lexical resources.

Object-Based Image Analysis (OBIA) has been successfully used to map slums. In general, the occurrence of uncertainties in producing geographic data is inevitable. However, most studies concentrated solely on assessing the classification accuracy and neglecting the inherent uncertainties. Our research analyses the impact of uncertainties in measuring the accuracy of OBIA-based slum detection. We selected Jakarta as our case study area, because of a national policy of slum eradication, which is causing rapid changes in slum areas. Our research comprises of four parts: slum conceptualization, ruleset development, implementation, and accuracy and uncertainty measurements. Existential and extensional uncertainty arise when producing reference data. The comparison of a manual expert delineations of slums with OBIA slum classification results into four combinations: True Positive, False Positive, True Negative and False Negative. However, the higher the True Positive (which lead to a better accuracy), the lower the certainty of the results. This demonstrates the impact of extensional uncertainties. Our study also demonstrates the role of non-observable indicators (i.e., land tenure), to assist slum detection, particularly in areas where uncertainties exist. In conclusion, uncertainties are increasing when aiming to achieve a higher classification accuracy by matching manual delineation and OBIA classification.

Web-Based GIS is a platform that deals with the representation, management and storage of locational information for real-time online retrieval, viewing and manipulations. Web-based GIS incorporate all the functions of information systems: gathering, storing, retrieving, visualizing and dissemination of spatial information on the Internet. In modern-day GIS serve as vital means to not only geo-referenced locational information that are been retrieved but also the development in web-based technologies as well as there involvements in decision making processes. In recent time the increased used of GIS on the Internet have totally transformed and made three distinct changes across our GIS environment. These are: (i) how are GIS data being accessed (ii) what are modes of its transmission and (iii) what available GIS functionalities are within the environment for analysis. This paper examines the applications and technologies associated with web-based GIS architectures with an emphasis on the internet GIS based structure and case studies of GIS Web-based applications in MapInfo, Microsoft Silverlight Technology and the ArcGIS Server using ArcGIS JavaScript API.

A significant number and range of challenges besetting sustainability can be traced to the actions and interactions of multiple autonomous agents (people mostly) and the entities they create (e.g., institutions, policies, social network) in the corresponding social-environmental systems (SES). To address these challenges, we need to understand decisions made and actions taken by agents, the outcomes of their actions, including the feedbacks on the corresponding agents and environment. The science of Agent-based Complex Systems—ACS science—has a significant potential to handle such challenges. The advantages of ACS science for sustainability are addressed by way of identifying the key elements and challenges in sustainability science, the generic features of ACS, and the key advances and challenges in modeling ACS. Artificial intelligence and data science promise to improve understanding of agents’ behaviors, detect SES structures, and formulate SES mechanisms.

Wearable assistant devices play an important role in daily life for people with disabilities. Those who are hearing impaired may face dangers while walking or driving on the road. The major danger is their inability to hear warning sounds from cars or ambulances. Thus, the goal of this study is to develop a wearable assistant device for the hearing impaired to recognize emergency vehicle sirens on the road using edge computing. An EfficientNet-based fuzzy rank-based ensemble model was proposed to classify seven audio sounds, including human vocalizations and emergency vehicle sirens. This model was embedded in an Arduino Nano 33 BLE Sense development board. The audio files were respectively obtained from the CREMA-D dataset and Large Scale Audio dataset of emergency vehicle sirens on the road, with a total number of 8756 files. The seven audio sounds included neutral vocalization, anger vocalization, fear vocalization, happy vocalization, car horn sound, siren sound, and ambulance siren sound. The audio signal was converted into a spectrogram by the short-time Fourier transform as the feature. When one of the car horns, sirens, or ambulance sirens was detected, the wearable assistant device presented alarms through vibration and messages on the OLED panel. The performances of the EfficientNet-based fuzzy rank-based ensemble model in offline computing achieved an accuracy of 97.1%, precision of 97.79%, sensitivity of 96.8%, and specificity of 97.04%. In edge computing, the results were an accuracy of 95.2%, precision of 93.2%, sensitivity of 95.3%, and specificity of 95.1%. Thus, the proposed wearable assistant device has the potential benefit of helping the hearing impaired avoid traffic accidents.

Graphene-based nanomaterials (GNMs), including graphene, graphene oxide, reduced graphene oxide, and graphene quantum dots, may have direct anticancer activity or be used as nanocarri-ers for antitumor drugs. GNMs usually enter tumor cells by endocytosis and can accumulate in lysosomes. This accumulation prevents drugs bound to GNMs from reaching their targets, sup-pressing their anticancer effects. A number of chemical modifications are made to GNMs to facili-tate the separation of anticancer drugs from GNMs at low lysosomal pH and to enable lysosomal escape of drugs. Lysosomal escape may be associated with oxidative stress, permeabilization of the unstable membrane of cancer cell lysosomes, release of lysosomal enzymes into the cytoplasm, and cell death. GNMs can prevent or stimulate tumor cell death by inducing protective autopha-gy or suppressing autolysosomal degradation, respectively. Furthermore, because GNMs prevent bound fluorescent agents from emitting light, their separation in lysosomes may enable tumor cell identification and therapy monitoring. In this review, we explain how the characteristics of the lysosomal microenvironment and the unique features of tumor cell lysosomes can be exploited for GNM-based cancer therapy.

This study was designed to extend the literature on multicomponent interventions for the children of deaf adults (CODA) population. This study used two evidence-based behavior intervention strategies: pre-session pairing (PSP) and independent group contingency (GC). These strategies have been successfully used to decrease off-task behavior in elementary school children with various abilities and diverse backgrounds. However, the research on multicomponent interventions has yet to examine their effects on the CODA population in inclusive classrooms. This study used a concurrent multiple baseline design across participants with an ABC sequence to examine teacher-implemented PSP with independent GC in reducing the off-task behavior of three CODAs in an inclusive classroom at a public elementary school. The results show that the intervention successfully decreased off-task behavior for all participating CODAs. The results suggest that CODAs can adapt to classroom rules and expectations when PSP and independent GC are systematically applied to them in classrooms.

Event-based vision is an emerging field of computer vision that offers unique properties such as asynchronous visual output, high temporal resolutions, and dependence on brightness changes to generate data. These properties can enable robust high-temporal-resolution object detection and tracking when combined with frame-based vision. In this paper, we present a hybrid, high-temporal-resolution, object detection and tracking approach, that combines learned and classical methods using synchronized images and event data. Off-the-shelf frame-based object detectors are used for initial object detection and classification. Then, event masks, generated per each detection, are used to enable inter-frame tracking at varying temporal resolutions using the event data. Detections are associated across time using a simple low-cost association metric. Moreover, we collect and label a traffic dataset using the hybrid sensor DAVIS 240c. This dataset is utilized for quantitative evaluation using state-of-the-art detection and tracking metrics. We provide ground truth bounding boxes and object IDs for each vehicle annotation. Further, we generate high-temporal-resolution ground truth data to analyze the tracking performance at different temporal rates. Our approach shows promising results with minimal performance deterioration at higher temporal resolutions (48 – 384 Hz) when compared with the baseline frame-based performance at 24 Hz.

The recent covid crisis has proven important lessons for academia and industry regarding digital reorganization. Among fascinating lessons from these times is the huge potential of data analytics and artificial intelligence. The crisis exponentially accelerated the adoption of analytics and artificial intelligence, and this momentum is predicted to continue into the 2020s and over. Moreover, drug development is a costly and time-consuming business, and only a minority of approved drugs return the revenue that exceeds the research and development costs. As a result, there is a huge drive to make drug discovery cheaper and faster. With modern algorithms and hardware, it is not too surprising that the new technologies of artificial intelligence and other computational simulation tools can help drug developers. In only two years of covid research, many novel molecules have been designed/identified using artificial intelligence methods with astonishing results in terms of time and effectiveness. This paper will review the most significant research on artificial intelligence in the de novo drug design for COVID-19 pharmaceutical research.

Maternal-child care is one of the foundations of primary health care. Nurses’ competency skills they have been taught. Community awareness is an important part of preventive healthcare, and nurses must be aware of the factors that impact the health of the community. This study examines the effectiveness of lecture-based instructions in maternal and child care and its implications to students' social competency skills and community awareness in Nursing Colleges in Nueva Ecija, Philippines. The researcher uses survey questionnaire and employed the descriptive design where fifteen (15) nursing students and five (5) teachers were purposively selected. The findings revealed that the weighted mean for the effectiveness of lecture based instruction in maternal and child care is 3.91 with verbal description of “Effective”, the effects of lecture based instruction in maternal and childcare to students’ social competency skills and community awareness got the weighted mean of 3.87 and interpreted as “very satisfactory” and the effectiveness of actual community-based instruction is very effective with weighted mean of 4.25 and is higher compare to lecture based instruction. The results also revealed that students and teachers were challenged in lecture-based instruction in maternal and chi8ldcare during distance learning. Recommendations for the enhancement of lecture-based instruction in maternal and childcare in social competency skills and community awareness were also made.

Over the last decade, a significant literature has emerged that advocates the potential of different Additive manufacturing (AM) technologies and printable polymeric materials. Nevertheless, large scale printing and complex geometric shapes, with curvatures and non-planar layer deposition, are a challenging process for the traditional gantry-based machine. The 3 degrees of freedom cartesian configuration restricted their capability to planar layered printing and restricted part dimensions. To date, many researchers have used industrial robots to overcomes this limitation. This review gives the reader a good overview of the FDM technique due to its scalability, cost efficiency and a wide range of material printability. A strong emphasis is laid on the PLA and PLA-based composites as promising materials for the FDM process applications. The second part of this paper links the successful use of these materials in the traditional printing process to large scale printing using the robot-based FDM process. This survey presents representative setups for robot-based AM and works that have been used these setups for non-planar material deposition. Finally, we conclude this paper by identifying opportunities for realizing new functional capabilities by exploiting robot-based AM, and we also present the future trends in this area.

For centuries, crop plants have represented the basis of the daily human diet. Among them, cereals and legumes, accumulating oils, proteins and carbohydrates in their seeds, distinctly dominate modern agronomic practice. Indeed, these plants play an essential role in the food industry and fuel production. Therefore, the seeds of crop plants are intensively studied by food chemists, biologists, biochemists, and nutritional physiologists. Accordingly, not only seed development and germination, but also age- and stress-related alterations in seed vigor, longevity, nutritional value and safety can be addressed by a broad panel of analytical, biochemical and physiological methods. Currently, functional genomics is one of the most powerful tools, giving direct access to characteristic metabolic changes, accompanying plant development, senescence and response to biotic or environmental stress. Among individual methodological platforms, proteomics represents one of the most effective ones, giving access to cellular metabolism at the level of proteins. Here we discuss the main methodological approaches employed by seed proteomics in the context of physiological changes related to seed development, ageing and response to environmental stress.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Copper (Cu) is an essential micronutrient for the correct development of eukaryotic organisms. This metal plays a key role in many cellular and physiological activities, including enzymatic activity, oxygen transport, and cell signaling. Although the redox activity of Cu is crucial for enzymatic reactions, this property also makes it potentially toxic when found at high levels. Due to this dual action of Cu, highly regulated mechanisms are necessary to prevent both the deficiency and the accumulation of this metal since its dyshomeostasis may favor the development of multiple diseases, such as Menkes’ and Wilson’s diseases, neurodegenerative diseases, diabetes mellitus, and cancer. As the relationship between Cu and cancer has been the most studied, we analyze how this metal can affect three fundamental processes for tumor progression: cell proliferation, angiogenesis, and metastasis. Gynecological diseases are characterized by high prevalence, morbidity, and mortality, depending on the case, and mainly include benign and malignant tumors. The cellular processes that promote their progression are affected by Cu, and the mechanisms that occur may be similar. We analyze the crosstalk between Cu deregulation and gynecological diseases, focusing on therapeutic strategies derived from this metal.

The primary objective of this study is to synthesize, elucidate the structural properties, and ex-plore the biological activity of novel metal complexes derived from 6-methyl-2-thiouracil and 6-propyl-2-thiouracil. The paper outlines a synthesis method and assesses the antimicrobial activ-ity of newly formed Cu(II) and Pd(II) complexes with two substituted 2-thiouracil ligands. The structural attributes of these newly developed compounds are thoroughly discussed based on data derived from melting point analysis, MP-AES for Cu and Pd, UV-Vis, IR, ATR, 1H NMR, 13C NMR and Raman spectroscopy. The interpretation of the complex spectra is assisted by the data for 6-methyl-2-thiouracil and 6-propyl-2-thiouracil obtained from 1H-1H COSY, DEPT-135, HMBC and HMQC spectra. In addition, the antimicrobial activity of these complexes and the free ligands are assessed against both Gram-positive and Gram-negative bacteria, as well as yeasts.