Carbon dioxide (CO2), a major greenhouse gas, capture and separation has recently become a crucial technological solution to reduce atmospheric emissions from fossil fuel burning. Thereafter, many efforts have been put forwarded to reduce the burden on climate change by capturing and separating them especially from larger power plants by the utilization of different technologies. Those technologies have often suffered from high operating cost and huge energy consumption. On right side, physical process such as adsorption is very cost effective process which have been widely used to adsorb different contaminants including CO2. Henceforth, this review covers the overall efficacies of CO2 capture by the utilization of carbon based materials through adsorption technology. Subsequently, we also address the associated challenges and future opportunities of carbon based materials (CBMs). For CO2 capture, it was found that CBMs followed the order of carbon nanomaterials (i.e., graphene, graphene oxides, carbon nanotubes and their composites) < mesoporous -microporous or hierarchical porous carbons < biochar and activated biochar < activated carbons.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

CASBEE-City tool determines the city’s Built Environment Efficiency (BEE) by calculating the improvement of Quality of Life (Q) over human activities’ Environmental Load (L) within the city’s hypothetical boundary. A total of 58 variables (57 Q indicators and one variable for L) are used in the worldwide version of CASBEE-City which were grounded using ISO 37120:2014 Sustainable Development of Communities and 17 Sustainable Development Goals (SDGs) by the United Nations (UN). This paper examines the application of CASBEE-City for Malaysian cities using the case of Johor Bahru City and identifies assessment indicators which are customised based on the data availability, reliability and suitability through focus group discussions (FGDs) which involved 36 respondents (researchers, urban planners and stakeholders). This paper reveals Johor Bahru with moderate score B+ in 2010 and 2025. Consensus were also achieved from the 36 FGD respondents for the practicability and future potential of CASBEE-City and BEE framework in Johor Bahru.

The remaining capacity can only be measured with offline method. This brings great challenge for the online prediction of Li-ion battery’s RUL. A novel online prediction method for Li-ion battery’s RUL was proposed, which is based on multiple health indicators (HIs) and can be derived from the batteries’ historical operation data. Firstly, four indirect HIs were built according to the battery’s operation current, voltage and temperature data respectively. On that basis, a generalized regression neural network (GRNN) was developed to estimate the battery’s remaining capacity, and the non-linear autoregressive approach (NAR) was utilized to predict the battery’s RUL based on the estimated capacity value. Furthermore, to reduce the interference, twice wavelet denoising were performed with different thresholds. A case study is conducted with a NASA battery dataset to demonstrate the effectiveness of the method. The result shows that the proposed method can obtain Li-ion batteries’ RUL effectively.

The questions on who is entitled to benefit from REDD+ transactions remains one of the most controversially debated issues around cooperative efforts to reduce deforestation in developing countries. REDD+ has been conceived as international framework for voluntary efforts of developing countries to reduce greenhouse gas emissions and enhance carbon removals from forest activities. Designed as international framework under the UNFCCC that calculates emission reductions and removals (ERRs) at the national -and as an interim step on the subnational level – REDD+ is primarily a creature of international law. However, in defining forest-carbon ERRs the international framework competes with national emission trading systems and domestic REDD+ legislation as well as private standards that define units traded on the voluntary carbon market. The definition of various carbon units is closely linked to the question on who is entitled to participate in REDD+ and benefit from the sale of ERRs under results-based payment schemes or carbon market transactions. This paper applies a legal lens to the various claims to participate in REDD+ transactions. It tries to disentangle the various rights to ERRs, various carbon credits, and payments that come with REDD+ and that almost always create confusion and not seldom conflict around REDD+ implementation. The definition of carbon rights and the legal nature of carbon credits depends on local law and differs between countries. However, there are a number of legal considerations that apply and certain underlying concepts are relevant for the understanding of REDD+ transactions and the allocation of benefits and burdens of conservation activities.

The effects of carbon fiber hybridisation on the thermal properties of woven kenaf reinforced epoxy composites kenaf fibre were studied. Woven kenaf hybrid composites at the different weave designs of plain and satin, and fabric count of 5 × 5 and 6 × 6 were manually prepared by vacuum infusion technique. Thermal properties of pure carbon fibre and hybrid composites were conducted by using thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC). It was found that at high kenaf fibre content showed better thermal stability while the highest thermally stable was found in pure carbon fibre composite. The TG and DTG results showed that the amount of residue decreased in plain-designed hybrid composite compared to satin-designed hybrid composite. The DSC data revealed that the presence of woven kenaf increase decomposition temperature.

The paper describes preliminary studies on the influence of humidity on the electrical resistance of a textile sensor made of carbon fibers. The concept of the sensor refers to externally bonded fiber reinforcement commonly used to strengthen building structures. However, the zig-zag arrangement of carbon fiber tow allows measuring strains, as it is done in popular resistive strain gauges. The sensor tests proved its effectiveness in the measurement of strains, but also showed a high sensitivity to changes in the temperature and humidity which unfavorably affects the readings and their interpretation. The influence of these factors must be compensated. Due to the size of the sensor, there is not possible electrical compensation by the combining of several sensors into the half or full Wheatstone bridge circuit. Only mathematical compensation based on known humidity resistance functions is possible. The described research is the first step to develop such relations. The tests were carried out at temperatures of 10 °C, 20 °C and 30 °C, with changing the humidity in the range of 30-90%.

The purpose of this paper was to analyze the development trend of hazardous chemical packaging towards low carbon economy from both qualitative and quantitative perspectives. Four types of relatively small volume packaging with volume/weight less than 450L/400kg, respectively, and three intermediate bulk containers (IBCs), which are widely used for hazardous chemicals were studied to calculate the carbon footprint (CF) from cradle to grave using life cycle assessment (LCA) method and to predict the future carbon emission of hazardous chemical packaging in the next five years (2016-2020), based on the export data of Tianjin Port in China. Grey model (GM) was adopted in the prediction. The results showed that majority of IBCs have lower carbon footprint than other types when the packaging contained same amount of same hazardous chemical. With the development of international trading, the demand of hazardous chemicals will increase as well. As the result, carbon emission generated by hazardous chemical packaging will increase accordingly. However, based on GM simulation result, increasing the amount of IBC use will effectively reduce the relative amount of carbon emission.

A novel type of graphene-like quantum dots, synthesized by oxidation and cage-opening of C60 buckminsterfullerene, has been studied as a fluorescent and absorptive probe for heavy-metal ions. The lattice structure of such unfolded fullerene quantum dots (UFQDs) is distinct from that of graphene since it includes both carbon hexagons and pentagons. The basic optical properties, however, are similar to those of regular graphene oxide quantum dots. On the other hand, UFQDs behave quite differently in the presence of heavy-metal ions, in that multiple sensitivity to Cu2+, Pb2+ and As(III) was observed through comparable quenching of the fluorescent emission and different variations of the transmittance spectrum. By dynamic light scattering measurements we confirmed, for the first time in metal sensing, that this response is due to multiple complexation and subsequent aggregation of UFQDs. Nonetheless, the explanation of the distinct behaviour of transmittance in the presence of As(III) and the formation of precipitate with Pb2+ require further studies. These differences, however, also make it possible to discriminate between the three metal ions in view of the implementation of a selective multiple sensor.

The feasibility of using full ion kinetics, instead of gyrokinetics, in simulating low-frequency Ion-Temperature-Gradient (ITG) instabilities in tokamaks has recently been demonstrated by Sturdevant et al. [Physics of Plasmas 24, 081207 (2017)]. In that work, a variational integrator was developed to integrate the full orbits of ions in toroidal geometry, which proved to be accurate in capturing both the short-time scale cyclotron motion and long time scale drift motion. The present work extends that work in three aspects. First, we implement a relatively simple full orbit integrator, the Boris integrator, and demonstrate that the accuracy of this integrator is also sufficient for simulation of ITG instabilities. Second, the equilibrium magnetic configuration is extended to general toroidal configuration specified numerically, enabling simulation of realistic equilibria reconstructed from tokamak experiments. Third, we extend that work to the nonlinear regime and investigate the nonlinear saturation of ITG instabilities. To verify the new numerical implementation of the orbit integrator and magnetic configuration, the linear electrostatic ITG frequency and growth rate are compared with those given in Sturdevant's work and good agreement is found.

Immobilization enables enzymes to be held in place so that they can be easily separated from the product when needed and can be used again. Conventional methods of immobilization include adsorption, encapsulation, entrapment, cross linking and covalent binding. However, conventional methods have several drawbacks including reduced stability, loss of biomolecules, less enzyme loading or activity and limited diffusion. The aim of this study is the evaluation of importance of nanomaterials for the immobilization of industrially important enzymes. Nano materials are now in trend for the immobilization of different enzymes due to their physiochemical properties. Gold nanoparticles, silver nanoparticles, nano diamonds, graphene, carbon nanotubes and others are used for immobilization. Among covalent and non-covalent immobilization of enzymes involving both single and multiwalled carbon nanotubes, non-covalent immobilization with functionalized carbon nanotubes is superior. Therefore, enzymes immobilized with nanomaterials possess greater stability, retention of catalytic activity and reusability of enzymes

The region of Eastern Europe & Turkey contributed to the SISAL (Speleothem Isotopes Synthesis and AnaLysis) global database with stable carbon- and oxygen isotope time-series from 18 entities from 14 cave systems. The currently available oldest record from this region is the ABA-2 flowstone record (Abaliget Cave; Hungary) reaching back to MIS 6. The temporal distribution of the compiled 18 entities points out a ~20-kyr-long period, centering around 100 ka, lacking speleothem stable isotope record in the region. The regional subset of SISAL_v1 records displays a continuous coverage for the past ~90 kyr for both δ¹⁸O and δ¹³C, with a mean temporal resolution of ~12 yr for the Holocene, and >50 yr for the pre-Holocene period. The highest temporal resolution both for the Holocene and the pre-Holocene was achieved in the So-1 record (Sofular Cave; Turkey). Assessing the data, an important split was found regarding the climatic interpretation of speleothem δ¹⁸O. While the oxygen isotope composition of more continental formations is thought to reflect mainly temperature variations and changes in moisture transport trajectories, it may strongly reflect fluctuations of precipitation amount in the southern part of the region. Variations of δ¹³C primarily interpreted as humidity changes reflecting dry/wet periods across the region. Elevation gradients from three non-overlapping time periods from the region - for the last 5kyr - indicated systematically prevailing elevational gradients around -0.26‰ 100m^-1 in δ¹⁸O. The regional comparison of SISAL_v1 speleothem δ¹⁸O and the temporal distribution of coarsely crystalline cryogenic cave carbonate occurrences back to 45ka does not appear to confirm the finding that occurrence of the latter coincides with the warming from stadial to interstadial conditions.

The sustainable production of food faces formidable challenges. Foremost is the availability of arable soils, which have been ravaged by the overuse of fertilizers and detrimental soil management techniques. As such, maintenance of soil quality, and reclamation of marginal soils, has become an increasingly important endeavor. Recently, there has been emerging interest in the use of biochar, a carbon rich, porous material thought to improve various aspects of soil performance. Biochar (BC) is produced through the thermochemical decomposition of organic matter at high temperature in an oxygen limited environment, in a process known as pyrolysis. Importantly, the source of organic material, or ‘feedstock,’ used in this process and different parameters of pyrolysis, especially temperature, determine the chemical and physical properties of biochar. Incorporation of BC impacts soil-water relations, tilth and nutrient status, pH, soil organic matter (SOM), and microbial activity. Soil amendment with BC has been shown to have an overall positive impact on soil health and crop productivity; however, initial soil properties need to be considered prior to the application of BC. There is an urgent need to understand the effects of long-term field application of BC and how it influences the soil microcosm. This knowledge will facilitate predictable enhancement of crop productivity and meaningful carbon sequestration.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

Ionic liquids (ILs) have gained interest among researchers due to its tunable properties that can be used in wide applications. However, toxicity and bio-degradation studies of ILs proved that most of the aromatic ILs, such as imidazolium is highly toxic and non-biodegradable. Several advance oxidation processes (AOPs) have been investigated by researchers to evaluate the efficiency of the systems for the removal of ILs from wastewater. However, the issue on relative high cost and environmental concern has limited the application of these AOPs in industry. In this research, photocatalytic study using hybrid nano-materials was conducted to evaluate the efficiency of this system as an alternative AOP system for removal of ILs from wastewater. The synergistic effect of adsorption-photodegradation was introduced by depositing Fe-TiO₂ onto the functionalized activated carbon (AC). Nano-TiO₂ was synthesized using micromulsion method before modification with transition metal and deposited onto the oxidized AC. Photodegradation reaction of 1-butyl-3-methylimidazolium chloride [bmim]Cl was investigated under simulated visible light irradiation. It was observed that the overall efficiency of the system was increased with the increasing amount of Fe dopant. Investigation on the extrinsic factors such as solution pH, initial concentration of ILs and photocatalyst dosage showed to significantly affect the overall efficiency of the systems where the optimum condition for the system was observed at pH 10, with initial ILs at 1mM at 1 g/L of photocatalyst. The best performance photocatalyst was 0.2Fe-TiO₂/AC.

Mass timber products, together with careful forestry management, could help decarbonize the construction industry. These products must be long-lasting, to safely store atmospheric carbon for decades or centuries, and multi-functional, to displace materials and equipment that are emissions-intensive. This paper shows how to optimize mass timber panels as heat-exchangers, suggesting how to eliminate insulation while simplifying HVAC systems. Test panels measured the heat-exchange in steady and transient conditions, when the ventilation was driven by a fan or by thermal buoyancy. The total heatexchange was predicted accurately by theory in all cases. Further investigation is needed to understand the possible heat-recovery effects at the exterior surface.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

It is required to manage sustainable Short-Rotation Coppices (SRCs) as an important role on carbon sink and bioenergy output, because most of SRCs were established in reclaimed land in South Korea. However, during the last three years, growth pattern of the SRCs was remarkably changed with soil condition. This study aimed to identify the sustainability of SRCs on carbon storage, biomass and fuel pellet production, monitoring the neighboring vegetation of SRCs by land-use exchange, physiological change of poplar on seasonal trend, and to evaluate whether poplar is suitable for making wood pellets. The calculated biomass yield per area of poplar grown was 103.07 Mg per total area (55.6 ha), and volumes of carbon dioxide absorption was estimated to be 330 Mg CO2. Wood pellet quality based on the criteria scored third grade, indicating that poplar is suitable for manufacturing fuel pellets. Moreover, monitoring of the flora distribution in SRCs revealed changes in species composition. As halophyte was increased during drought, soil organic matter, net growth and total chlorophyll of poplar were significantly decreased. These findings indicated that photosynthesis and growth pattern of SRCs may be negatively affected by microclimate and will provide valuable information for effective management of SRCs.

Ag+ pollution is great of harm to the human body and the biology. Therefore, it is an urgent need to develop inexpensive and accurate detection methods. Herein, lignin-derived structural memory carbon nanodots (CSM-dots) with outstanding fluorescence property were fabricated via a green method, which reserve functional and structural units of the precursor molecules. The CSM-dots could specifically bind Ag+, accompanied with a remarkable fluorescence quenching response. This “turn-off” fluorescence behavior was used for Ag+ determination in a linear range of 5-290 μM with the detection limit as low as 500 nM. Furthermore, the finding showed that this sensing nano-platform was successfully used for Ag+ determination in real samples and intracellular imaging, showing great potential in biological and environmental monitoring applications.

Ecological footprint calculators are digital tools that help individuals calculate their environmental or climate impact, with the aim of stimulating pro-environmental behaviour change. These footprint calculators typically take an information-provision approach, but this strategy assumes that increased levels of knowledge result in increased levels of pro-environmental behaviour (i.e., a reduced footprint). This is not a given – existing literature on the relationship between environmental knowledge and pro-environmental behaviour is inconclusive, and this relationship may be different from that of environmental knowledge and ecological footprint. As such, we investigated the relationship between environmental knowledge and ecological footprint as estimated by a footprint calculator. 448 Dutch participants completed an online survey, including an ecological footprint calculator. We found no evidence for a relationship between environmental knowledge and ecological footprint calculator outcome. Rather, an exploratory analysis of our data showed that environmental values were more important predictors of ecological footprint. The finding that increased levels of knowledge are not related to a reduced ecological footprint suggests that calculators would do well to move beyond information provision, and employ additional behaviour change strategies. Based on our exploratory analysis, we provide several concrete examples of potential strategies.

Magnetic nanoparticles are met across many biological species ranging from magnetosensitive bacteria, fishes, bees, bats, rats, birds, to humans. They can be both of biogenetic origin and due to environmental contamination, being either in paramagnetic or ferromagnetic state. The energy of such naturally occurring single-domain magnetic nanoparticles can reach up to 10-20 room k_BT in the magnetic field of the Earth, which naturally led to supposition that they can serve as sensory elements in various animals. This work explores within a stochastic modeling framework a fascinating hypothesis of magnetosensitive ion channels with magnetic nanoparticles serving as sensory elements, especially, how realistic it is given a highly dissipative viscoelastic interior of living cells and typical sizes of nanoparticles possibly involved.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

The conservation of coastal wetland ecosystems, like mangrove forests and salt marshes, represents a critical strategy for mitigating atmospheric emissions and climate change in the 21st century. Yet the existence of these environments is threatened by human-induced disturbances, namely deforestation and accelerated sea-level rise. Coastal systems maintain surface elevation in response to sea-level rise through a combination of physical and biological processes both above and below the ground surface. The quantification and relative contribution of belowground process controls (e.g., seasonal water content, organic matter decomposition) on surface elevation change is largely unexplored but crucial for informing coastal ecosystem sustainability. To address this knowledge deficit, we integrated measurements of surface elevation change of the live root zone (0.5 to 1 m depth) with geotechnical data from co-located sediment cores in the Sundarbans mangrove forest (SMF) of southwest Bangladesh. Core data reveal that the primary belowground controls on surface elevation change include seasonal fluctuations in pore-water content and the relative abundance of fine-grained sediments capable of volumetric expansion and contraction, supporting an elevation gain of ~2.42 ± 0.26 cm yr⁻¹. In contrast to many mangrove environments, the soils of the SMF contain little organic matter and are dominantly composed (>90%) of inorganic clastic sediments. The mineral-rich soil texture likely leads to less compaction-induced subsidence as compared to organic-rich substrates and facilitates surface equilibrium in response to sea level rise. Despite a relatively high soil bulk density, soil carbon (C) density of the SMF is very low owing to the dearth of preserved organic content. However, rates of C accumulation are balanced out by locally high accretion rates, rendering the SMF a greater sink of terrestrial C than the worldwide mangrove average. The findings of this study demonstrate that C accumulation in the SMF, and possibly other alluvial mangrove forests, is highly dependent on the continued delivery of sediment to the mangrove platform and associated settings.

Tree resin, which in addition to its widespread use in industry is also a macroergic component which has not yet been used for energy purposes. The main goal of this work is to determine the energy content of the resin of spruce, pine and larch and wood components – pulp and turpentine. The combustion heats of resin (MJ/kg) from each timber was determined calorimetrically. The energy values of tree resin (&gt;38.0 MJ.kg-1) were 2.2 and 2.4 times higher than that of bleached and unbleached cellulose, the highest value was recorded for the turpentine (&gt;39.0 MJ.kg-1). The best way of resin tapping is the America method, providing 5 kg resin ha-1 yr-1. The resin quantity tapped was raised at least 3 times applying stimulant, its production cost compared to other feedstocks was the cheapest. The tree resin can be applied as a good means to mitigate global warming and consequently dampen climate change. One tonne of tree resin burned instead of coal spares the atmosphere by 5.0 Mt CO2 since it is environmentally neutral. As resin heating values approach to the lower end of ones of liquid hydrocarbon fuels, greater efforts are needed to examine the most efficient energy use of resin.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

China’s transportation industry has made rapid progress, which has led to a mass of carbon emissions. However, it is still unclear how the carbon emission from transport sector is punctuated by shifts in underlying drivers. This paper aims to examine the process of China’s carbon emissions from transport sector as well as its major driving forces during the period of 2000 to 2015 at the provincial level. We firstly estimate the carbon emissions from transport sector at the provincial level based on the fuel and electricity consumption using a top-down method. We find that the carbon emission per capita is steadily increasing across the nation, especially in the provinces of Chongqing and Inner Mongolia. However, the carbon emission intensity is decreasing in most provinces of China, except in Yunnan, Qinghai, Chongqing, Zhejiang, Heilongjiang, Jilin, Inner Mongolia, Henan and Anhui. We then quantify the effect of socio-economic factors and their regional variations on the carbon emissions using panel data model. The results show that the development of secondary industry is the most significant variable in both the entire nation level and the regional level, while the effects of the other variables vary across regions. Among these factors, population density is the main motivator of the increasing carbon emissions per capita from transport sector for both the whole nation and the western region, whereas the consumption level per capita of residents and the development of tertiary industry are the primary drivers of per capita carbon emissions for the eastern and central region.

Fluorescent carbon dots (C-dots) were synthesized by one pot hydrothermal treatment of garlic juice at 180 °C for 7h. The as-prepared C-dots with an average diameter of 2.13±0.71 nm can be well dispersed, and show absinthe fluorescence with a quantum yield of 8.9% in water. The C-dots were fully characterized by TEM, XPS, XRD, and FTIR, respectively. Additionally, the as-prepared C-dots reveal nearly nontoxic to SW480 cells and can be used for cell imaging. The water solution of C-dots show sensitivity to pH values and metal ions, and also have a high selectivity to the Hg²⁺ ion among other transition metal ions, and achieve a high sensitive detection with the detection limit of 0.45 μM. The fluorescent C-dots are expected to be useful for the evaluation of mercury ions in environmental water system.

As one of the critical state parameters of the battery management system, lithium battery state of charge (SOC) can provide an essential reference for battery safety management, charge/discharge control, and energy management of electric vehicles. To analyze the application of deep learning in electric vehicle power battery SOC estimation, this study reviewed the technical process, common public datasets, and the neural networks used, structural characteristics, advantages and disadvantages of lithium battery SOC estimation in deep learning method. First, the specific technical processes of the deep learning method for SOC estimation were analyzed, including data collection, data preprocessing, feature engineering, model training, and model evaluation. Secondly, the current commonly and publicly used lithium battery dataset was summarized. Then, the input variables, data sets, errors, and advantages and disadvantages of four types of deep learning methods, were concluded using the structure of neural network used for training as the classification criterion. Finally, the challenges and future development directions of lithium battery SOC estimation in deep learning method were explained.

Actuated carbon (AC) is utilized in various conditions of uses after its disclosure as a solid and dependable adsorbent. A review on AC is introduced along with returning to the wellsprings of AC age; strategies used to produce AC including pyrolysis enactment; actual actuation; synthetic initiation and steam pyrolysis. The significant variables influencing the AC creation, the potential uses of AC and their future possibilities are likewise examined. AC is applied in water, wastewater and leachate medicines in numerous nations, particularly to clean the shading, eliminate the smell and some substantial metals. Taking into account this, an exhaustive rundown of research on compound, physical and organic change strategies of initiated carbon relating to prevent of foreign substance expulsion from watery arrangements was aggregated and investigated. Additionally, the examination of the actual blending strategy and the impregnation technique in enactment with antacid metals shows that the actuated carbon got through actual blending had a higher porosity than the initiated carbon created by the impregnation technique. The uses of initiated carbon items were quickly surveyed.

Carbon concrete PAN/lignin-based CF composites are a new promising material class for the building industry. The replacement of the traditional heavy and corroding steel reinforcement by carbon fiber (CF) based reinforcements offers many significant advantages: a higher protection of environmental resources because of lower CO2 consumption during cement production, a longer lifecycle and thus muss less damage in structural components and a higher degree of design freedom because lightweight solutions can be realized. However, due to cost pressure in civil engineering, completely new process chains are required to manufacture CF based reinforcement structures for concrete. The article describes the necessary process steps in order to develop CF reinforcement: (1) the production of cost-effective CF using novel carbon fiber lines, (2) the fabrication of CF rebars with different geometry profiles. It was found that PAN/lignin-based CF is currently the most promising material in order to meet the future market demands. However, significant research needs to be undertaken in order to improve the properties of lignin-based and PAN/lignin-based CF, respectively. The CF can be manufactured to CF-based rebars using different manufacturing technologies which have been developed on prototype level in this study.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Photosynthetic activities of the sago palm (Metroxylon sagu Rottb.) were studied to find out its sensitivity to changes in ambient air temperature. The minimum ambient air temperature designed for the experiment was 25–29⁰C, while the higher end was 29–33⁰C. Several photosynthetic parameters were studied to support our analysis in sago photosynthetic activity, including diurnal leaf gas exchange, assimilation rate vs. CO₂ concentration, leaf greenness, leaf chlorophyll content, and photosynthetic rate vs. irradiance. We found that sago palm photosynthetic activity tends to be more sensitive to minimum than to maximum ambient air temperature. The plants exposed to higher air temperatures had dark green leaf color associated with higher rates of diurnal photosynthesis, chlorophyll content, and rubisco limited photosynthetic activity. They also exhibited higher trend in optimum irradiance absorption level. Consequently, maximum light energy dissipation occurred at higher temperatures.

Greenhouse Gases (GHGs) emission has considerable impact on global warming and climate change. Since energy systems and their features noticeably influence on the amount of GHGs emission, it can be modeled based on the specifications of energy sources utilized by the countries. In addition, economic activity is another factor which should be considered in GHG emission modeling. In this work, Artificial Neural Network (ANN) is used for estimating carbon dioxide emission, as one of the most abundant GHGs, on the basis of shares of various energy sources used as primary energy supply and GDP as an indicator for economic activities. Five countries including Iran, Kuwait, Qatar, Saudi Arabia and United Arab Emirates (UAE) are considered as case studies. Comparing between the estimated data by the achieved model and actual quantities showed acceptable precision of the ANN model for prediction of carbon dioxide emission. The average absolute relative error and the R-squared values of the GMDH model are approximately 2.28% and 0.9998, respectively. The obtained values for the mentioned statistical criteria show the precision of the model in forecasting the emission of Co2.

Cuboid diamonds are particularly common in the placers of the northeastern Siberian platform but their origin remains unclear. These crystals usually range in color from dark yellow to orange and more interestingly, are characterized by unusual low aggregated nitrogen impurities (non-aggregated C-center) suggesting a short residence time and/or low temperatures at which they have been stored in the mantle. In order to track possible isotopic signature that could help deciphering cuboid diamond's crystallization processes, δ¹³C values, δ¹⁵N values and nitrogen contents have been determined in-situ in three samples using secondary ion mass spectrometry (SIMS), whereas nitrogen aggregation state have been determined by FTIR spectroscopy. The samples fall out the δ¹³C vs. δ¹⁵N field of canonical mantle composition. Different scale of carbon and nitrogen fractionation may produce the observed variations. Alternatively, mixing of mantle and crustal material would obscure initial co-variations of δ¹³C values with δ¹⁵N or nitrogen content.

Voltage-gated Ca²⁺ (Ca_v) channels play pivotal roles in regulating gene transcription, neuronal excitability, and neurotransmitter release. In order to meet the spatial and temporal demands of visual signaling, Ca_v channels exhibit unusual properties in the retina compared to their counterparts in other areas of the nervous system. Here, we review current concepts regarding the specific subtypes of Ca_v channels expressed in the retina, their intrinsic properties and forms of modulation, and how their dysregulation could lead to retinal disease.

In this work, we propose an easy and a low cost method for the synthesis of Nitrogen-Doped Graphene NDG and its silver nanowires NW functionalization NWGN. The synthesis was performed using the improved graphene oxide method, chemical reduction of graphene oxide in the presence of caffeine as green nitrogen source and the subsequently the silver nanowires growth in the surface, by the chemical reductions salts in the presence of NG. Achieving a homogeneous growing (coating) of graphene sheets. The samples were analyzed using conventional characterization techniques: SEM-EDX, XRD, FT-IR, RAMAN, TEM, HRTEM, STEM and XPS.

Therapeutic options for the highly pathogenic human Severe Acute Respiratory Syndrome-Coronavirus 2 (SARS-CoV-2) causing the current pandemic Coronavirus disease (COVID-19) are urgently needed. COVID-19 is associated with viral pneumonia and acute respiratory distress syndrome causing significant morbidity and mortality. The proposed treatments for COVID-19, such as hydroxychloroquine, remdesivir and lopinavir/ritonavir, have shown little or no effect in the clinic. Additionally, bacterial and fungal pathogens contribute to the SARS-CoV-2 mediated pneumonia disease complex. The antibiotic resistance in pneumonia treatment is increasing at an alarming rate. Therefore, carbon-based nanomaterials (CBNs), such as fullerene, carbon dots, graphene, and their derivatives constitute a promising alternative due to their wide-spectrum antimicrobial activity, biocompatibility, biodegradability and capacity to induce tissue regeneration. Furthermore, the antimicrobial mode of action is mainly physical (e.g. membrane distortion), which is characterized by a low risk of antimicrobial resistance. In this review, we evaluated the literature on the antiviral activity and broad-spectrum antimicrobial properties of CBNs. CBNs had antiviral activity against 12 enveloped positive-sense single-stranded RNA viruses similar to SARS-CoV-2. CBNs with low or no toxicity to the humans are promising therapeutics against COVID-19 pneumonia complex with other viruses, bacteria and fungi, including those that are multidrug-resistant.

This review discusses a broad range of recent advances (2013-2017) of chemical imaging using electrochemical methods, with a particular focus on techniques that have been applied to study cellular processes, or techniques that show promise for use in this field in the future. Non-scanning techniques such as microelectrode arrays (MEAs) offer high time-resolution (< 10 ms) imaging, however at reduced spatial resolution. In contrast, scanning electrochemical probe microscopies (SEPMs) offer higher spatial resolution (as low as a few nm per pixel) imaging, with images collected typically over many minutes. Recent significant research efforts to improve the spatial resolution of SEPMs using nanoscale probes, and to improve the temporal resolution using fast scanning have resulted in movie (multiple frame) imaging with frame rates as low as a few seconds per image. Many SEPM techniques lack chemical specificity or have poor selectivity (defined by the choice of applied potential for redox-active species). This can be improved using multifunctional probes, ion-selective electrodes and tip-integrated biosensors, although additional effort may be required to preserve sensor performance after miniaturization of these probes. We discuss advances to the field of electrochemical imaging, and technological developments which are anticipated to extend the range of processes that can be studied. This includes imaging cellular processes with increased sensor selectivity and at much improved spatiotemporal resolution than has been previously customary.

The transportation sector significantly contributes to greenhouse gas emissions, thus imposing sig-nificant environmental hazards. In response, many nations have begun promoting Electric Vehicles (EVs) as an ecologically sustainable substitute for traditional combustion vehicles. Lithium-Ion Batteries (LIBs), characterized by their high energy density, extended lifespan, and relatively low self-discharge rate, have become the suitable energy storage system for EVs, advancing the field of sustainable transportation. The decreasing cost of LIB production has primarily driven this progression, realized through a combination of economies of scale, advancements in electrode materials and cell design, and re-finements in manufacturing processes. All these elements collectively contribute to the cost reduc-tion of LIBs. A foreseeable implication of this trend is an expected surge in LIBs that will exhaust their operational lifespan and, consequently, be cast away into the environment. One mitigating strategy for this impending environmental issue involves collecting these spent EV batteries, re-configuring them, and repurposing them for applications with less rigorous weight, performance, and size prerequisites. This approach would not only prolong the utility life of the batteries but also ameliorate their environmental impacts. Nevertheless, second-life batteries are anticipated to exhibit a higher rate of gas evolution, necessitating comprehensive testing and readjustments to ensure safe operation in secondary ap-plications. The regulatory framework encompassing the second-life battery sector still needs to be defined regarding norms, technical standards, and legislation. This paper aims to elucidate the primary regulations and technical standards proposed thus far in the second-life battery marketplace. The results underscore the exigency for neutral evaluative entities, such as universities, research centers, and governmental institutions, to perform an unbi-ased assessment of the second-life battery market. This would pave the way for novel technical standards and legislative measures specifically tailored to this emerging sector.

High-performance poly(1,4-butylene terephthalate (PBT) nanocomposites have been developed via the consideration of phosphorus-containing agents and amino-carbon nanotube (A-CNT). One-pot functionalization method has been adopted to prepare functionalized CNTs via the reaction between A-CNT and different oxidation state phosphorus-containing agents, including chlorodiphenylphosphine (DPP-Cl), diphenylphosphinic chloride (DPP(O)-Cl), and diphenyl phosphoryl chloride (DPP(O3)-Cl). These functionalized CNTs, DPP(Ox)-A-CNTs (x = 0, 1, 3), were respectively mixed with PBT to obtain the CNTs-based polymer nanocomposites through a melt blending method. SEM observations demonstrated that DPP(Ox)-A-CNT nano-additives were homogeneously distributed within PBT matrix compared to A-CNT. The incorporation of DPP(Ox)-A-CNT improved the thermal stability of PBT. Moreover, PBT/DPP(O3)-A-CNT showed the highest crystallization temperature and tensile strength, due to the superior dispersion and interfacial interactions between DPP(O3)-A-CNT and PBT. PBT/DPP(O)-A-CNT exhibited the best flame retardancy resulting from the excellent carbonization effect. The radicals generated from decomposed polymer were effectively trapped by DPP(O)-A-CNT, leading to the reduction of heat release rate, smoke production rate, carbon dioxide and carbon monoxide release during cone calorimeter tests.

Carbon dioxide capture and storage (CCS) is highly expected to be mitigating the discharges of carbon dioxide in a surrounding environment. Solvents are an integral part of CCS. So far, several solvents have been explored the interest of meeting the requirements such as accessibility, non-harmfulness, biocompatibility, recyclability, and inexpensiveness. However, most solvents face failure in fulfilling the requirements due to many factors, so, this review paper gives a brief discussion about another category of solvent, an analogue of ionic liquids (ILs) named deep eutectic solvent (DES). Extensive research has been done on DES in recent years because of their various attractive advantages, i.e., non-poisonousness, biodegradability, cheap cost and easy preparation, that make them as a promising green solvent for many industrial procedure and application, for instance, polymer synthesis, biodiesel treatment, green chemistry, electrochemistry etc. Therefore, this manuscript mainly focusses on CO2 capturing through DES in oil and gas field. In addition, the preparation and chemical structures of this novel solvent (DES) is also discussed. Moreover, a detailed study based on experimental solubility of CO2 in DESs is also reported in this article.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

Earth’s land surface area is raised from conventionally flat 15 to 64 Gha to account for hilly undulation and soil relief detail. Three main aspects are: topography, rugosity/tortuosity and micro-relief/porosity of vegetation-free ground. Recalibration is arrived at from four approaches: first, direct empirical estimates from the few compiled satellite or LiDAR data with means of +2.5–26% progressively overlain by +94% at cm² scale for soil ruggedness then +108% for mm² micro-relief; second, from digital elevation models with 1.6–2.0 times flat areas; third, by ‘reverse engineering’ global soil bulk densities and carbon reserves requiring x 2–6 land. Finally, a Fermi estimation conveniently sets the World’s new surface area – that exposed to Sun, air and rain – at 100 Gha (with 36 Gha flat ocean). Soil organic carbon (SOC) is thence raised to 8,580 Gt mainly in SOM/humus with its biotic complexity plus roots, VAM-fungi and leaf-litter, that itself = 17,800 Gt. Although four to six times IPCC’s or NASA/NOAA’s calculations of just 1,500–2,300 Gt SOC, this is likely an underestimation. Global biomass and biodiversity are at least doubled (x 2–3.5) and net primary productivity (NPP) similarly increased on land to >270 Gt C yr^-1 due to terrain.

Objectives: The promising specific growth regulators are employed tissue culture of the bamboo species. The specific natural hardening mixture supports the acclimatization and adaptation of the protected cultivation. The bamboo species contribute to the carbon sequestration and stabilization of the environment. Findings: The growth regulator 2, 4-D encourages callus induction and growth regulators NAA + TDZ, BAP + Kinetin + Gelrite, BAP + Kinetin + Coconut water + myo-inositol, NAA and TDZ impose plant regeneration in the Bambusa species. The growth regulator of 2,4-D, 2,4-D + Kinetin, 2,4-D + BA, 2,4-D + BAP and 2,4-D + NAA + BAP produces callus induction in the Dendrocalamus species. The growth regulator of TDZ, BA and IBA + Coumarin + Putrescine, BAP + GA3, NAA + Kinetin, BA + IBA, BA + Kinetin + NAA, NAA + Kinetin, Kinetin + IAA has facilitated shoot regeneration in the Dendrocalamus species with the specific period. The growth regulator of BA and TDZ; BAP + TDZ, IBA + Coumarin + Putrescine, BAP + GA3, NAA + Kinetin, BA + IBA, BA + Kinetin + NAA, NAA + Kinetin, Kinetin + IAA develops root regeneration with unambiguous time in the Dendrocalamus species. The growth regulator of BAP and Kinetin + BAP imposes shoot regeneration and IBA and IBA + Coumarin + sucrose conducts root regeneration in the edible bamboo. The natural hardening materials of cocopeat, vermicompost, perlite, cow dung, FYM, compost, soil & garden soil and humus soil, perlite, and FYM recommend in the acclimatization and adaptation of the Bambusa species and Dendrocalamus species respectively. Novelty: The standard growth regulators and hardening mixtures impose tissue culture, acclimatization and adaptation in the bamboo species. The bamboo species involves in managing carbon sequestration, biogeochemical cycle and the environment.

The UK economy is overly reliant on unsustainable production and consumption practices, depleting finite resources at rates that will increase production costs, business risk and economic instability. This over-consumption produces emissions and waste that cause climate change and environmental degradation, impacting on the wellbeing of people in the UK and beyond. The Resource Recovery from Waste programme (RRfW) promotes a transition towards waste and resource management in a circular economy that restores the environment, creates societal benefits and promotes clean growth by engaging relevant actors in the transition process. RRfW collaborates with academia, government, and industry to co-produce a shared vision and approach to realise such a transition. Reflecting insights from RRfW’s government engagement, this article presents a positive outlook for changing the UK economy and society. It envisions a long-term future for waste and resource management that maximises the value of materials by circulating them in the economy for as long as possible. Four themes and an approach are proposed, including recommendations for regulatory instruments and a stable policy framework. It recommends further collaborative research to capitalise on opportunities for economic growth, innovation and resilient infrastructure whilst contributing to quality jobs and welfare in all four UK nations.

Objective: Rett syndrome (RTT) is an X-linked neurodevelopmental disorder caused by mutations in MeCP2, a transcription factor. MeCP2 mutations cause abnormal expression of downstream genes and eventually lead to brain dysfunction. The role of MeCP2 in brain neural development remains unclear. To further elucidate this role, a MeCP2-null rat model was created with the CRISPR/cas9 system. Method: A MeCP2-cas9 vector was constructed and then microinjected into fertilized rat ova in vitro. Two mutations by CRISPR/cas9 were confirmed to cause deletions in exon 2 of MeCP2 via DNA sequencing, and protein expression was measured by Western blotting. Transcriptome data for three brain tissues, the cerebellum, cerebral cortex and hippocampus, were obtained via next-generation sequencing. Results: MeCP2-null rats were successfully obtained, and preliminary analysis showed that the MeCP2-null rats exhibited motor dysfunction and anxious and depressed behaviour. In addition, differentially expressed genes (DEGs) were identified in the three MeCP2-null brain tissues compared to wild-type rat brain tissues. In the rat cerebellum, 388 downregulated DEGs were mainly involved in the calcium ion signalling pathway and the PI3K-Akt signalling pathway. In the cerebral cortex, 386 upregulated DEGs were primarily involved in intracellular signal transduction, protein phosphorylation and the MAPK signalling pathway. In the hippocampus, the DEGs were related to the MAPK signalling pathway. Conclusion: We constructed a MeCP2-null rat model with unique features with CRISPR/cas9 technology to study RTT and analysed DEGs in three rat brain tissues to highlight potential targets for the development of new medicines.

The structural, electronic and magnetochemical properties of the star-shaped polyoxopalladate [Pd₁₅O₁₀(SeO₃)₁₀]¹⁰⁻ (POPd) and its lanthanide functionalized derivatives have been investigated on the basis of density functional theory followed by a ligand field analysis using the Radial Effective Charge (REC) model. Our study predicts that heteroPOPd is a robust cryptand that enforces D_5h symmetry around the encapsulated Ln³⁺ centers. This rigid coordination environment favors interesting potential magnetic behavior in the Er and Ho derivatives, which may be of interest for molecular spintronics and quantum computing applications.

Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

Acute ischemic strokes are the third leading cause of death and the leading cause of neurological disability worldwide. The oxygen and glucose deprivation associated with ischemic strokes not only leads to neuronal cell death, but also increases the inflammatory response and decreases functional output of the brain. The only intervention approved by US Federal Drug and Food Administration for treatment of ischemic strokes is tissue plasminogen activator (tPA), however, such treatment can only be given within 4.5 hours of the onset of stroke-like symptoms. This narrow time-range limits its application, and it also might induce detrimental rather than beneficial effects to stroke patients by treatment of the tPA. In order to reduce the infarct volume of an acute ischemic stroke while increasing the time period for treatment, emerging therapies reveal great potential by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors with monoclonal antibody (MAB). With successfully application in the treatment of cancer patient by MAB, in this review, we will focus on recent advances on stroke therapy by using MAB on the treatment of stroke by targeting inflammation, growth factors, ion channels, and neurotransmitter receptors. Therefore, developing specific MAB targeting the signaling pathway of stroke will contribute to stroke therapy.

We report a new fabrication method for a fully stretchable supercapacitor based on single wall carbon nanotube (SWCNT)-coated electrospun rubber nanofibers as stretchable supercapacitor electrodes. The deposition conditions of SWCNT on hydrophobic rubber nanofibers are experimentally optimized to induce a uniform coating of SWCNT. For surfactant-assisted coating of SWCNT, both water contact angle and sheet resistance were the lowest compared to the cases with other surface treatment methods, indicating the most effective coating approach. The excellent electromechanical properties of this electrode under the stretching condition is demonstrated by the measurement of Young’s modulus and normalized sheet resistance. This superb tolerance of the electrode with respect to stretching results from i) high aspect ratios of both nanofiber templates and the SWCNT conductors, ii) highly elastic nature of rubbery nanofiber, and iii) strong adherence of SWCNT-coated nanofiber on the elastic ecoflex substrate. Electrochemical and electromechanical measurements on the stretchable supercapacitor devices reveal that the volumetric capacitance (15.2 F cm-3 at 0.021 A cm-3) of the unstretched state is maintained for strains of up to 40 %. At this level of strain, the capacitance after 1,000 charge/discharge cycles is not significantly reduced. The high stability of our stretchable device suggests potential future applications in various types of wearable energy storage devices.

The acoustic emission (AE) technique was applied to monitor the pitting corrosion of carbon steel in NaHCO₃ + NaCl solutions. The open circuit potential (OCP) measurement and the corrosion morphology in-situ capturing using optical microscope were conducted during AE monitoring. The corrosion micromorphology was characterized with scanning electron microscope (SEM). The propagation behavior and AE features of natural pitting on carbon steel were investigated. After the performing of signal processing including pre-treatment, shape preserving interpolation and denoising for raw AE waveforms, three types of AE signals can be classified in the correlation diagrams of new waveform parameters. Finally, a 2D pattern recognition method was established to calculate the similarity of different continuous AE graphics, which is quite effective to distinguish the localized corrosion from uniform corrosion.

Herein, we evaluated the electrophoretic deposition of nanohydroxyapatite/superhydrophilic multiwalled carbon nanotube composites (nHAp/MWCNT) onto stainless steel biomedical alloys for applications in bone tissue engineering. First, nHAp/MWCNT composites were dispersed into 0.042 mol L⁻¹ of Ca(NO₃)₂·4H₂O + 0.025 mol L⁻¹ NH₄H₂PO₄ electrolytes (pH = 4.8) at two different concentrations. Next, a voltage of −2 V was applied using 316L stainless steel as a working electrode and (0.27 cm²), a high-purity platinum coil wire as the auxiliary electrode, and an Ag/AgCl(3 M) electrode was used as the reference electrode. The nHAp/MWCNT composites were characterized by transmission electron microscopy. The deposited nHAp and nHAp/MWCNT films were characterized by profilometry, scanning electron microscopy, X-Ray diffractometry and Raman spectroscopy. Human osteoblast cells were cultivated with the different materials, and in vitro cytotoxicity was evaluated using lactate dehydrogenase (LDH) assay. The osteogenesis process was evaluated by mRNA levels of the three genes that are directly related to bone repair: Alkaline Phosphatase, Osteopontin and Osteocalcin. We showed that rough, crystalline apatite thin films containing phases of nHAp were successfully deposited onto 316L stainless steel alloys. Also, we noticed that nHAp/MWCNT thin films deposited onto 316L stainless steel alloys upregulated the expression of important genes related to bone mineralization and maturation. Our results strongly support the possibility of this new alternative to modify the surface of metallic biomedical alloys to promote bone tissue regeneration.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

Alternative fuels available at low cost, friendly to natural environments and meet the energy needs and demands, have witnessed a growing demand and use today. Ethanol is an attractive renewable energy source with a high content of oxygen. Ethanol can be produced through ethanolisis, however for this work direct blending of conventional diesel, waste plastic pyrolysis oil and ethanol with commercial fuel improver CI-0808 purchased from Innospec company was attempted. The primary purpose of adding a cetane improver was to improve the combustion characteristics of the blends by at least 1- 3 ignition quality points. Five mixing ratios were chosen in the following order, 50:25:25, 60: 20:20, 70: 15:15, 80: 10:10 and 90: 5:5 for Waste Plastic Pyrolysis Oil (WPPO), ethanol and conventional diesel (CD) respectively. However, for the fuel additive mixing ratio the total volume percentage was considered and the ratio put at 0.01% of the total quantity of blended fuel. In this work WPPO, diesel blends and fuel additives improvers were used as alternative fuel. This was to evaluate their performance and emission characteristics in a stationary single cylinder water cooled experimental diesel engine. The CI-0808 was added due to its potential power to reduce emissions of CO, UHC, NO_X, PM and improved engine performance. The results obtained were compared carefully to ASTM standards and discussed using graph curves figures and tabulated values. The conclusion was that ethanol and WPPO blends can be used in diesel engines as alternative fuel without modification. Used in combination with cetane improvers the emissions reduce significantly and performance improved equalling that of conventional diesel fuel.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

Due to low working temperature, high energy density and low pollution, proton exchange fuel cells have been investigated under different operating conditions in different applications. Using platinum catalysts in methanol fuel cells leads to increasing the cost of this kind of fuel cell which is considered as a barrier to the commercialism of this technology. For this reason, a lot of efforts have been made to reduce the loading of the catalyst required on different supports. In this study, carbon black (CB) and carbon nanotubes (CNT) have been used as catalyst supports of the fuel cell as well as using the double-metal combination of platinum-ruthenium (PtRu) as anode electrode catalyst and platinum (Pt) as cathode electrode catalyst. The performance of these two types of electro-catalyst in the oxidation reaction of methanol has been compared based on electrochemical tests. Results showed that the carbon nanotubes increase the performance of the micro-fuel cell by 37% at maximum power density, compared to the carbon black. Based on thee-electrode tests of chronoamperometry and voltammetry, it was found that the oxidation onset potential of methanol for CNT has been around 20% less than CB, leading to the kinetic improvement of the oxidation reaction. The current density of methanol oxidation reaction increased up to 62% in CNT sample compared to CB supported one, therefore the active electrochemical surface area of the catalyst has been increased up to 90% by using CNT compared to CB which shows the significant rise of the electrocatalytic activity in CNT supported catalyst. Moreover, the resistance of the CNT supported sample to poisonous intermediate species has been found 3% more than CB supported one. According to the chronoamperometry test results, it was concluded that the performance and sustainability of the CNT electro-catalyst show remarkable improvement compared to CB electro-catalyst in the long term.

We investigate the ammonium removal abilities of natural and synthetic zeolites, which have distinct Si/Al ratios and various surface areas, to study how adsorption and ion-exchange processes in zeolites perform under different ammonium concentrations and different temperatures. Five zeolites including natural mordenite, chabazite, erionite, clinoptilolite and synthetic merlinoite were immersed in 20 mg/kg, 50 mg/kg and 100 mg/kg ammonium solutions. The results demonstrate that zeolites under high ammonium concentrations (100 mg/kg) possess higher physical adsorption capacity (0.398–0.468 meq/g), whereas those under lower ammonium concentrations (20 mg/kg) possess greater ion-exchange property (64–99%). The ion-exchange ability of zeolites are extremely dependent on the cation content of the zeolites, and the cation content is affected by the Si/Al ratio. The surface area of zeolites also has a partial influence on its physical adsorption ability. When the surface area is less than 100 m²/g, the adsorption ability of zeolite increases obviously with surface area; however, adsorption ability is saturated as the surface area becomes larger than this critical value of 100 m²/g. When we carried out the zeolites in 50 mg/kg ammonium concentration at different temperatures (5~50 ℃), we found that zeolites exhibit the highest ammonium removal ability at 30°C and the potassium release was enhanced at 30~40 ℃.

We have proposed a data-driven approach for designing mesoscale porous structures of Li-ion battery electrode with three-dimensional virtual structures and machine learning techniques. Over 2,000 artificial 3D structures assuming positive electrode composed of random packed spheres as active material particles are generated, and charge/discharge resistance has been evaluated using simplified Physico-chemical model. In this model, resistance from Li diffusion in active material particles (diffusion resistance), transfer resistance of Li+ in electrolyte (electrolyte resistance) and reaction resistance on the interface between active material and electrolyte are simulated based on mass balance of Li, Ohm’s law in and linearized Butler-Volmer equation, respectively. Using these simulation results, regression models via Artificial Neural Network (ANN) have been created in order to predict charge/discharge resistance from porous structure features. In this study, porosity, active material particle size and volume fraction, pressure in the compaction process, electrolyte conductivity, and binder volume fraction are adopted as features, associated with controllable process parameters for manufacturing battery electrode. As results, the predicted electrode resistance by ANN regression model is good agreement with the simulated values. Furthermore, sensitivity analysis and optimization of the process parameters have been carried out. The proposed data-driven approach could be a solution as a guiding principle for manufacturing battery electrode.

A new disease causing the tan to light brown blighted stems and pods has occurred in 2.6% pea (Pisum sativum L.) plants with an average disease severity rating of 3.7 in Chapainawabganj district, Bangladesh. A fungus with white appressed mycelia and large sclerotia was consistently isolated from symptomatic tissues. The fungus formed funnel-shaped apothecia with sac-like ascus and endogenously formed ascospores. Healthy pea plants inoculated with the fungus produced typical white mold symptoms. The internal transcribed spacer sequences of the fungus were 100% similar to that recovered from an epitype of Sclerotinia sclerotiorum, considering the fungus to be the causative agent of white mold. Mycelial growth and sclerotial development of S. sclerotiorum were favored at 20°C and pH 5.0. Glucose was the best carbon sources to support hyphal growth and sclerotia formation. Bavistin and Amistar Top inhibited the radial growth of the fungus completely at the lowest concentration. In planta, foliar application of Amistar Top showed the considerable potential to control the disease at 1.0% concentration until 7 days after spraying, while Bavistin prevented infection significantly until 15 days after spraying. A large majority (70.93%) of genotypes including tested released pea cultivars were susceptible, while six genotypes (6.98%) appeared resistant to the disease. These results could be important for management strategies aiming to control the incidence of S. Sclerotinia and eliminate yield loss in pea.

Electric Vehicles (EVs) are increasing the interdependence of transportation policies and the electricity market. EMMEV (Electricity Market Model with Electric Vehicles) is an experimental agent-based model that analyses how carbon reduction policy in transportation may increase number of Electric Vehicles and how does that would influence on the electricity price. Agents are ESCOs (Energy Service Providers) which can distribute fuels and their objective is to maximize their profit. In this paper, EMMEV is used to analyze the impacts of the LCFS (Low Carbon Fuel Standard), a performance-based policy instrument, on electricity prices and EV sales. The agents in EMMEV/regulated parties in LCFS should meet a certain CI (Carbon Intensity) target for their distributed fuel. In case, they cannot meet the target, they should buy credit to compensate for their shortfall and if they exceed, they can sell their excess. The results, considering the assumptions and limitations of the model, show that the banking strategy of the agents contributing in the LCFS might have negative impact on penetration of EVs, unless there is a regular Credit Clearance to trade credits. It is also shown that the electricity price as result of implementing the LCFS and increasing number of EVs has increased between 2–3 percent depending on banking strategy.

Literature is inconsistent as to how coffee affects the features of the metabolic syndrome (MetS), and which bioactive compounds are responsible for its metabolic effects. We aimed to compare the in-vivo effects of unfiltered coffee with a selected mixture of its compounds on diet-induced MetS. 24 male Sprague-Dawley rats were fed a high-fat (35% W/W) food plus 20% W/W fructose in drinking water for 14 weeks, and were randomized into three groups: control, coffee, or nutraceuticals (5-O-caffeoylquinic acid, caffeic acid, and trigonelline). Coffee or nutraceuticals were provided in drinking water in a dosage equal to 4 cups/day in a human. Compared to the controls, only coffee supplementation decreased total food intake, weight gain, and estimated average plasma glucose. Surrogate measures of insulin resistance (fasting insulin, HOMA-IR, and oral glucose tolerance) were improved at endpoint in the coffee group. Circulating triglyceride levels were also reduced by coffee. Histopathological and quantitative measurements indicated lower grades of liver steatosis after long-term coffee consumption. In conclusion, a combination of phenolic acids and trigonelline was not as effective as coffee per se in improving the components of the MetS. This points to the role of other coffee chemicals and a potential synergism between compounds.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

We present a simple strategy to generate a family of carbon dot/iron oxide nanoparticles (C/Fe-NPs) that relies on the thermal decomposition of iron (III) acetylacetonate in the presence of a highly fluorescent carbon-rich precursor, while polyethylene glycol serves as the passivation agent. By varying the molar ratio of the reactants, a series of C/Fe-NPs have been synthesized with tuneable elemental composition in terms of C, H, O, N, Fe. The quantum yield is enhanced from 6% to 9% as the carbon content increases from 27% to 36%, while the room temperature saturation magnetization is improved from 4.1 emu/g to 17.7 emu/g as the iron content is enriched from 17 to 31%. In addition, the C/Fe-NPs show excellent antimicrobial properties, minimal cytotoxicity and demonstrate promising bioimaging capabilities, thus showing great potential for the development of advanced diagnostic tools.

The Philippines is both a biodiversity hotspot and a megadiverse country. The country also has experienced one of the highest rates of deforestation in Southeast Asia and is among the first countries to introduce a massive reforestation program to address the country’s rapid biodiversity and forest loss. Drawing upon an empirical study from the Leyte island and other relevant case studies from the Philippines, in this chapter, we demonstrate that recovering secondary forests following shifting cultivation, locally known as kaingin have the high potentials for biodiversity and carbon co-benefits. Based on our empirical study, we also found that secondary forest regrowing after kaingin use can potentially be used as a cost-effective reforestation measure with multiple benefits to people and the environment in upland areas of the Philippines. We also discuss measures that are essential for such programs to be successful.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

The application of graph theory in chemical and molecular structure research far exceeds people's expectations, and it has recently grown exponentially. In the molecular graph, atoms are represented by vertices and bonded by edges. Closed forms of multiplicative degree-based topological indices which are numerical parameters of the structure and determine physico-chemical properties of the concerned molecular compound. In this article, we compute and analyze many multiplicative degree-based topological indices of silicon-carbon Si₂C₃-I[p,q] and Si₂C₃-II[p,q].

Geopolymers are ecologically-friendly inorganic materials which can be produced at low temperatures from industrial wastes such as fly ash, blast furnace slags or mining residues. Although to date their principal applications have been as alternatives to Portland cement building materials, their properties make them suitable for a number of more advanced applications, including as photocatalytic nanocomposites for removal of hazardous pollutants from waste water or the atmosphere. For this purpose, they can be combined with photocatalytic moieties such as metal oxides with suitable bandgaps to couple with UV or visible radiation, or with carbon nanotubes or graphene. In these composites the geopolymers act as supports for the photoactive components, but geopolymers formed from wastes containing oxides such as Fe2O3 show intrinsic photoactive behaviour. This review discusses the structure and formation chemistry of geopolymers and the principles required for their utilisation as photocatalysts. The literature on existing photocatalytic geopolymers is reviewed, suggesting that these materials have a promising potential as inexpensive, efficient and ecologically-friendly candidates for the remediation of toxic environmental pollutants and would repay further development.

This study aligns with the 2030 United Nations Sustainable Development Goals- 3 which aim to “ensure healthy lives and promote well-being for all at all ages”. It contributes to the nascent literature stream on energy-health dynamics by introducing a holistic theoretical model to empirically examine the mediation effect of carbon emissions on the relationship between nonrenewable energy and infant mortality rates. Using an unbalanced panel data on 42 Asia and the Pacific countries from 2005 to 2015 and deploying the structural equation modeling approach, the empirical results are surmised as follows: (i) in regard to the full sample of countries, nonrenewable energy indirectly increases infant mortality rates through increasing carbon emissions. In other words, carbon emissions play a partial mediation role between nonrenewable energy and infant mortality rates; and (ii) for the different income groups, carbon emissions show varying mediation effects. For example, the mediation effects of carbon emissions in lower-middle and upper-middle income countries are found to be similar to those of the full sample of countries. Therefore, based on these findings, we conclude that nonrenewable energy is an essential determinant of infant mortality rates. Policy recommendations are put forward.

There is great importance and need of improving existing carbon materials fabrication methods. As such, this work proposes to discuss, interrogate, and propose viable hydrothermal, solvothermal, and other advanced carbon materials synthetic methods. The advanced carbon materials to be interrogated will include the synthesis of carbon dots, carbon nanotubes, nitrogen/titania-doped carbons, graphene quantum dots, and their nanocomposites with solid/polymeric/metal oxide supports. This will be done with special mind to microwave-assisted solvothermal and hydrothermal synthesis due to their favourable properties such as rapidity, low cost, and green/environmentally-friendliness. Thus, these methods are important during the current and future synthesis and modification of advanced carbon materials for application in energy, gas separation, sensing, and water treatment. Simultaneously, the work will pay special cognizance to methods reducing the fabrication costs and environmental impact while enhancing the properties as a direct result of the synthesis methods. As a direct result, the expectation is to impart a significant contribution to the scientific body of work regarding the improvement of the said fabrication methods.

A study is reported on the electrochemical alloying-dealloying properties of Mg₂Sn intermetallic compounds. ¹¹⁹Sn Mössbauer spectra of β-Sn powder, thermally alloyed cubic-Mg₂Sn and an intermediate MgSn nominal composition are used as references. The discharge of a Mg/micro-Sn half-cell led to significant changes in spectra line shape that are explained by a multiphase mechanism involving the coexistence of c-Mg₂Sn, distorted Mg_2-δSn and Mg-doped β-Sn. Capacities and capacity retention were improved by using nanoparticulate tin electrodes. This material reduces significantly the diffusion lengths for magnesium and contains surface SnO and SnO₂, which are partially electroactive. The half-cell potentials were suitable to be combined versus MgMn₂O₄ cathodes. Energy density and cycling properties of the resulting full Mg-ion cells are also scrutinized.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

Heavy metal ions (HMIs) have acute toxic effects on the health and are dangerous for human ex-istence and the ecosystem. Therefore, its sensitive and selective detection is of great importance. In recent years various nanocomposite materials have been used by researchers for the detection of HMIs by using various modalities of electrochemical techniques. This review article summarizes the recent advances in developing electrochemical sensors based on numerous nanocomposite mate-rials for detecting heavy metal ions. Nanocomposites materials, such as Metal-Organic Framework (MOF), organic conducting polymers (OCP), carbon nanotubes, graphene/reduced graphene oxide, graphitic carbon nitride, metal oxide, chitosan, mxenes, metal nanoparticle-based nanocomposites, etc. have been explored by various researchers to improve the sensing properties of electrochemical sensors. This review emphasized the synthesis and characterization techniques of nanocomposite materials, modalities for HMI detection by electrochemical technique and the electrochemical sensors. Moreover, this review highlights the development of portable biosensors for detecting HMIs in real-world scenarios, such as environmental monitoring, food safety, and clinical diagnosis. This review also demonstrates the importance of electrochemical sensors-based on nanocomposite ma-terials as a reliable, sensitive, and selective tool for detecting HMIs.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

Phosphorus (P) is an important element in a complete and balanced fertility program that can improve crop P use efficiency and ultimately productivity and profitability. Phosphatic fertilizers use without organic fertilizers leads to gradual decline in soil organic matter, native nutrient status and ultimately reduction in agricultural productivity and economic growth. The objectives of this was to evaluate P efficiencies with incorporation of peach sources, beneficial microbes and P application. From sustainability points of view, alternative use of different sources and forms of organic sources alone or in combination with inorganic P and beneficial microbes possess potential for improving productive capacity of the soil. Separate field experiments (one each on maize and soybean as a test crop) were conducted at Agriculture Research Institute Mingora Swat (ARI) for two consecutive years in summer season of 2016 (year one) and 2017 (year two). For the first time such a study were conducted to utilize peach leftovers and biomass (leaves, twigs, fruits, stones and barks partially decomposed, its compost and biochar) along with three phosphorus (P) levels (50, 75, 100 kg P ha-1) and two beneficial microbes (PSB and Trichoderma) on such a way to enhance soil sustainability and P use efficiency of soybean and maize. The results revealed that organic sources had significant effect on soybean and maize P use efficiency (PUE), P agronomic efficiency (PAE), partial factor productivity (PFPp) and soil P concentration. In experiment 1 among the organic sources, peach residues increased soil P (12.0 mg kg-1) as compared to peach compost and biochar (8.6 & 11.7 mg kg-1). Soil P concentration was maximum (12.1 mg kg-1) with PSB than Trichoderma (9.5 mg kg-1). Application of P at 100 kg ha-1increased soil P contents (16.9 mg kg-1) as compared to 50 and 75 kg P ha 1 (5.9 & 9.6 mg kg-1) respectively. P concentration was increased drastically in year 2 (12.4 mg kg-1) than year one (9.1 mg kg-1). PUE in both crops (soybean and maize) was maximum (25.6 & 28.4%) with peach biochar than compost and residues along with Trichoderma (21.7 & 27.8%). Highest PUE in soybean was recorded with 75 kg P ha-1(22.2%) however in maize maximum PUE was noted with 50 kg P ha-1(33.5%). PAE and PFPp in both crops was maximum with biochar and soil application of Trichoderma than other organic sources and PSB. Among the P levels highest PAE in soybean and maize was recorded with 75 kg ha-1whereas PFPp in soybean was maximum with 75 kg P ha-1 and interestingly in maize it was noted with 50 kg ha-1. Conclusively soybean and maize PAE, PFPp and PUE was higher with biochar, soil incorporation of Trichoderma and P at the rate of 75 kg ha-1 and can improve soybean and maize yield and soil productivity on sustainable basis.

Porous graphite was prepared without the use of template by rapidly heating the carbonization products from mixtures of anthracene, flourene, and pyrene with a CO₂ laser. Rapid CO₂ laser heating at a rate of 1.8 × 10 ⁶ °C/s vaporizes out the fluorene-pyrene derived pitch while annealing the anthracene coke. The resulting structure is that of graphite with 100 nm spherical pores. The graphitizablity of the porous material is the same as pure anthracene coke. Transmission electron microscopy revealed that the interface between graphitic layers and the pore walls are unimpeded. Traditional furnace annealing does not result in the porous structure as the heating rates are too slow to vaporize out the pitch, thereby illustrating the advantage of fast thermal processing. The resultant porous graphite was prelithiated and used as an anode in lithium ion capacitors. The porous graphite when lithiated had a specific capacity of 200 mAh/g at 100 mA/g. The assembled lithium ion capacitor demonstrated an energy density as high as 75 Wh/kg when cycled between 2.2 V to 4.2 V.

A new type of gold nanoparticles was synthesized by using benzoyl pyrazolone as a capping agent. The synthesized AuNPs exhibited a spherical shape and a monodisperse and fluorescence emission characteristic peak at 650 nm. The AuNPs –BMPBP was demonstrated as sensitive and selective fluorescent chemosensor for detection of Al ³⁺ ion. In the presence of Al ³⁺ ion, the fluorescent emission of BMPBP-AuNPs at 650 nm, increased with an increasing concentration of Al ³⁺ ion with a low detection limit (2 µM), the proposed method provided to apply determination of Al ³⁺ ion of tap water with satisfactory results.

In this study, functionalized-MWCNTs with 3-aminopropyltriethoxysilane (APTES) loaded titania nanoparticles (MWCNTs-APTES-TiO₂) were prepared to investigate their physicochemical properties and photocatalytic activity for methyl orange (MO) degradation. The TiO₂ nanoparticles, functionalized-MNCNT and composite powders were characterized by XRD, raman, and TEM. The results obtained proved that titania (TiO₂) nanoparticles was successfully loaded on APTES-MWCNTs. The best photocatalytic degradation of methyl orange solution under UV light irradiation was recorded over MWCNTs-APTES-TiO₂ (1:2), with 87% after 180 min. Kinetic analysis indicated that photocatalytic degradation of MO solution by MWCNTs-APTES-TiO₂ obeyed second-order kinetic model (R² > 0.95), supported by half-life equations and graph. The presence of carbon nanotubes accelerated the degradation of methyl orange due to inhibition of electron-hole recombination, the formation of additional hydroxyl radicals and functional groups of the latter had an inhibitory effect on the degradation of methyl orange. This study shows that the MWCNTs-APTES-TiO₂ nanocomposites exhibit promising photocatalytic degradation against methyl orange.

Activated carbons can be produced from biomass in a thermal process either in a direct carbonization-activation process or by first carbonizing the biomass and later on activating the biochars into activated carbons. The properties of the ACs are dependent on the type of process used for production. In this study, the properties of activated carbons produced in a one-stage and a two-stage process are considered. Activated carbons were produced by physical activation of two types of starting materials, bio chars produced from spruce and birch chips in a commercial carbonization plant and from the corresponding raw chips. The activated carbons produced were characterized regarding specific surfaces, pore volumes and pore size distributions. The un-activated bio chars had some degree of surface area 190 and 140 m²g^-1 for spruce and birch and pore volumes of 0.067 and 0.092 cm³g^-1. According to the results obtained, two slightly different types of activated carbons are produced depending if a one-stage or a two-stage carbonization and activation process is used. The ACs produced in the one-stage process had higher specific surface areas compared to the ones produced in a two-stage process (761-940 m²g^-1 vs. 540-650 m²g^-1) . In addition, total pore volumes were higher in one-stage process but development of micropores is greater compared to two-stage process. There was no significant difference in total carbon content between one-stage and two-stage process.

In Taiwan, farmers often apply excess compost to ensure adequate crop yield in highly frequent tillage, highly weathered, and lower fertility soils. The potential of biochar (BC) for diminishing soil C mineralization, and improving soil nutrient availability in compost over-fertilized soil is promising, but the study is still under-examined. To test the hypothesis, 434 days in vitro C mineralization kinetics of incubation experiment were conducted. Woody BC 0%, 0.5%, 1.0% and 2.0% (w/w) made of lead tree (Leucaena leucocephala (Lam.) de. Wit) were added to an Oxisols, and two Inceptisols of Taiwan. In each treatment, 5% swine manure compost (2 times recommended amount) was added and served as the over-fertilized soil. The results indicated that soil type strongly influenced the impact of BC addition on soil carbon mineralization potential. Respiration per unit of total organic carbon (total mineralization coefficient, TMC) of three studied soils significantly decreased with BC addition increased. Principal component analysis (PCA) suggested that for retaining more plant nutrients in addition to the effects of carbon sequestration, it is recommended that farmer could use locally produced biochars and composts in highly weathered and highly frequent tillage soil. Adding 0.5%-1% woody BC in soil should be reasonable and appropriate.

Site environments and instrumental characteristics of carbon dioxide (CO₂) measurements operated by local governments in the Kanto Plain, the center of which is Tokyo were summarized for this study. The observation sites were classified into environments of three types: urban, suburban, and woodland. Based on a few decades of accumulated hourly data, the diurnal and seasonal variations of CO₂ concentrations were analyzed as a composite of anomalies from annual means recorded for each site. In urban areas, the highest concentrations appear before midnight in winter. The second peak corresponds to the morning rush hour and strengthening of the inversion layer. Suburban areas can be characterized as having the highest concentration before dawn and the lowest concentration during the daytime in summer in association with the activation of respiration and photosynthesis of vegetation. In these areas, concentration peaks also appear during the morning rush hour. Woodland areas show background features, with the highest concentration in early spring: higher than the global background by about 5 ppmv.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

The UK Government is committed to reducing greenhouse gas (GHG) emissions by 80% by 2050. Buildings are responsible for 37% of the total GHG emissions in the UK and the need to reduce their emissions has resulted in more stringent building regulations in the recent past. The regulations, energy rating systems and voluntary guidelines — all are primarily aimed at reducing the need for heating and associated energy use by increasing insulation and air-tightness. However, future climates are projected to be warmer than the present day. Internal gains dominated non-domestic buildings will likely overheat, the adaptation to which will require energy-intensive cooling solutions, thus defeating the purpose of heating-focused regulations. This research investigated the effects of warming climate on overheating, and energy use and resulting emissions in representative urban office spaces in London in the present-day and future climates using hourly dynamic thermal simulations. Findings suggest that more airtight and highly—insulated office buildings designed for heating—dominated temperate UK climate will overheat in the 2050s. Heating demand reduces but electricity consumption increases by 121% when hybrid cooling is adopted to ameliorate overheating. Despite the rise, adopting a mixed-mode ventilation strategy was one of the ways of achieving overall energy efficiency while meeting benchmark overheating and carbon emissions target in present and future climatic contradictions. Current heating-focused legislations need to be urgently re-evaluated to account for the effects of climatic variability and overheating risks.

The adsorption of carbon dioxide on amino silanes-functionalized MCM-41 and SBA-15 materials is reported. The functionalization of mesoporous silicas was made by post-synthesis method, by impregnation of 3-aminopropyltriethoxysilane. The obtained materials were characterized by X-ray diffraction, scanning and transmission electron microscopies, nitrogen adsorption-desorption and X-ray photoelectron spectroscopy measurements. The carbon dioxide adsorption capacities for the samples were carried out under ambient pressures. The obtained results evidenced that amino-silanes with a terminal amine (–NH₂) were functionalized through covalent coupling of this group on the surface of the channels in the ordered mesoporous silica, meaning that the amine is anchored on the surface of the bigger pores of the MCM-41 and SBA-15 support. For functionalized materials, the CO₂ adsorption capacity of the AMCM-41 increased from 0.18 to 1.1 mmol·g⁻¹, whereas for ASBA-15, it was from 0.6 to 1.8 mmol·g⁻¹. The Lagergren kinetic algorithms were applied in order to validate the obtained results, evidencing the enhanced carbon dioxide adsorption capacity and stability of the functionalized ordered mesoporous molecular sieves.

Sulfonated carbon was used as an efficient and reusable heterogeneous solid acid catalyst for the synthesis of biodiesel via esterification of oleic acid with methanol under high voltage conditions. Using an inexpensive and reusable catalyst, environmental benignity, excellent yields in short times, synthesis in atmospheric pressure and low temperature conditions are some of the important features of this protocol. In the final results were confirmed by GC.

Global warming and climate change have led to extreme changes in climatic conditions in recent years. The Taiwan government designates the construction of the Kinmen County as low carbon islands, to promote the operation of 100 electric motorcycles and battery demonstration. This study combined with island tourism, after boarding the island, visitors can rent electric motorcycles from the passenger service center and coordinate with the island tour map to show the location of the battery exchange points, so as to facilitate the search. During the operation, the amount of electric motorcycle lease is 15,551 times, the total mileage of motor vehicle is 284,404 km, the number of battery exchange is 622 times, the lease income is about NT$900,000. To reduce carbon and economic benefits of the assessment, compared to the motorcycles (50 c.c), electric motorcycles (EM 100) can reduce the carbon emissions by 8,726 kg, reducing energy costs of NT$422,594.

To reduce the risk factors for mortality, the paper has focused on the assessment of the socioeconomic, clinical, physical, biophysiological, and biochemical characteristics of Down's syndrome which can be affected by the type of nutrition system, toxicity, and ecological footprint. Patients were males with trisomy 21 diagnosed by karyotype test and assessed by clinical examinations. Samples were collected from different biofluids. The physicochemical analyses of the biomatrix samples were performed and these properties had compared to findings of healthy males and age-matched controls. Duraphat application was proved effective for their oral treatment and saliva was the optimum biomarker for detecting malnutrition. Patients were hypersensitive to Cu while the Mn content in blood and hair was considered an expression to the degree of epileptic condition and chronic seizure development. The ecological footprint was 5.6 gha and carbon footprint was recognised in food poverty habits. These can be reduced by eating more plant-based proteins and fibre-rich foods with low saturated fats and sodium. The findings provide an up-to-date reference for expected developmental outcomes in children with DS in terms of biophysicochemistry. The genetically sensitive intervention is affected by heredity factor and sensitivity to toxics. Down's syndrome is encouraged to live green-hipster life.

The assessment of caprock integrity for underground storage of CO2 and/or enhanced oil recovery (EOR) systems is a multiscale endeavor. Caprock sealing behavior depends on coupled processes that operate over a broad range of length and time scales including nanoscale heterogeneity in capillary and wettability properties to depositional heterogeneity that is basin wide. Larger-scale sedimentary architecture, fractures, and faults can govern properties of potential “seal-bypass” systems that may be difficult to assess. We present a multiscale investigation of geologic sealing integrity of the caprock system that overlies the Morrow B sandstone reservoir, Farnsworth Unit, Texas, USA. The Morrow B sandstone is the target geologic unit for an on-going combined CO2 storage–EOR project by the Southwest Regional Partnership on Carbon Sequestration (SWP). Methods and/or data encompass small-to-large scales, including: petrography using electron and optical microscopy; mercury porosimetry; core examinations of sedimentary architecture and fractures; well logs; a suite of geomechanical testing; and a noble gas profile through sealing lithologies into the reservoir, as preserved from fresh core. The combined data set allows a comprehensive examination of sealing quality by scale, by primary features that control sealing behavior, and an assessment of sealing behavior over geologic time.

In this paper, a new anode environmentally friendly for hydrogen production was developed based on 430 stainless steel with an electrodeposited cobalt layer. The novelty of this work is the cobalt source once the electrodeposition bath was obtained from recycling of spent Li-ion batteries cathode with composition LiCoO₂. The electrodeposited cobalt behaves as supercapacitor in KOH 1M. In the linear voltammetry in KOH 1M, when the overpotential reaches 370 mV, the anodic density current for 430 SS/Co is 19 mA cm⁻². Thus, the anode developed in this paper achieves the double of density current with half of production cost if compared with 316SS. Moreover the anode construction described in this paper is an excellent option for Li- ion battery recycling.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

Today is the era of nanoscience and nanotechnology, which finds applications in the field of medicine, electronics, or environmental cleanup. Even though the nanotechnology is in its emerging phase, but still it provides solutions to numerous challenges. Nanotechnology and nanoparticles are found very effective because of their unique chemical and physical properties, high surface area, but their high cost is one of the major hurdles in its wider application. So, the synthesis of nanomaterials especially 2D nanomaterials from the industrial, agricultural and other biological activities could provide a cost-effective technique. The nanomaterials synthesized from such waste not only minimizes the pollution but also provides an eco-friendly approach towards the utilization of the waste. In the present review work, the emphasis has been given on the types of nanomaterials, different methods for the synthesis of 2D nanomaterials from the waste generated from industries, agriculture and their application in electronics, medicine and catalysis.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

The science on the anthropogenic airborne aerosols impacting upon the World Heritage marble monument, the Taj Mahal, at Agra has been studied in the light of modern physico-chemical approaches. The study is an effort to understand yet unrecognized airborne species which were found on the surface of the Taj Mahal monument. These species have been analyzed in the light of current analytical methods to impart characterization features and their possible impacts on the surface of the marble. Chemical constituents of these substrates which were incorporated over the top surface of the monument have been identified. Interestingly, the carbon particulates which were thought in the micro level, popularly called “particulate matters” has now been identified even in the nano domain entity, which are chemically more reactive, have been found on the surface of the monument. Because of their high chemical activity these nano carbons do play newer chemistry in the presence of air and sunlight generating several reactive oxygen species (ROS).These ROS are capable to respond to complicated chemical reactions on the surface of the marble in association with deposited cyanophyceae and other deposits of plant origin causing rapid degradation. This study provides the nature of onslaught borne out by such monument exposed under the prevalent smoggy environmental scenario.

Mangroves and salt marshes are among the most productive ecosystems in the global coastal ocean. Mangroves store more carbon (739 Mg CORG ha-1) than salt marshes (334 Mg CORG ha-1), but the latter sequester proportionally more (24%) net primary production (NPP) than mangroves (12%). Mangroves exhibit greater rates of gross primary production (GPP), above-ground net primary production (NPP) and plant respiration (RC) with higher PGPP/RC ratios, but salt marshes exhibit greater rates of below-ground NPP. Mangroves have greater rates of subsurface DIC production and, unlike salt marshes, exhibit significant microbial decomposition to a soil depth of 1 m. Salt marshes release more soil CH4 and export more dissolved CH4 , but mangroves release more CO2 from tidal waters and export greater amounts of POC, DOC and DIC to adjacent waters. Both ecosystems contribute only a small proportion of GPP, RE (ecosystem respiration) and NEP (net ecosystem production) to the global coastal ocean due to their small global area, but contribute 72% of air-sea CO2 exchange from the world’s wetlands and estuaries and contribute 34% of DIC export and 17% of DOC + POC export to the world’s coastal ocean. Thus, both wetland ecosystems contribute disproportionately to carbon flow of the global coastal ocean.

The land-surface developments of the European Centre for Medium-range Weather Forecasts (ECMWF) are based on the Carbon-Hydrology Tiled Scheme for Surface Exchanges over Land (CHTESSEL) and form an integral part of the Integrated Forecasting System (IFS), supporting a wide range of global weather, climate and environmental applications. In order to structure, coordinate and focus future developments and benefit from international collaboration in new areas, a flexible system named ECLand which would facilitates modular extensions to support numerical weather prediction (NWP) and society-relevant operational services, e.g. Copernicus, is presented . This paper introduces recent examples of novel ECLand developments on (i) vegetation, (ii) snow, (iii) soil, (iv) open water/lake (v) river/inundation, and (vi) urban areas. The developments are evaluated separately with long-range, atmosphere-forced surface offline simulations, and coupled land-atmosphere-ocean experiments. This illustrates the benchmark criteria for assessing both, process fidelity with regards to land surface fluxes and reservoirs of the water-energy-carbon exchange on the one hand, and on the other hand the requirements of ECMWF’s NWP, climate and atmospheric composition monitoring services using an Earth system assimilation prediction framework.

Hydrogen has been considered a future energy carrier for decades and the demand for hydrogen in refineries is always upward due to the revival of new technologies. The steam methane reforming method is frequently employed because of its high hydrogen generation efficiency at a cheap cost and minimal negative impact on the environment. But depending on the type of feedstock, one unit of hydrogen generate 9-10 units of CO2 that is needed to be treated for environmental sustainability. Therefore, the optimization of hydrogen production and CO2 capture is very important to address. The simulation research was conducted to anticipate and optimize steam reforming using Aspen HYSYS. A conversion-type reactor was used to develop this simulation-based model. The primary goal of this work is to investigate and optimize the production efficiency of hydrogen and the mitigation of CO2 that is generated from the steam reforming process by varying process parameters. CO2 capture efficiency was investigated at the different yields for hydrogen production and was found that a maximum of 98.8% of the CO2 can be absorbed using the proposed carbon capture system. Later, the Aspen Energy Analyzer tool revealed potential improvements for energy and cost optimization.

A sustainable diet which is healthy and environmental friendly is a climate change mitigation option in addition to being a health promoting diet. However, there is a scarcity of information if the Asian diets are sustainable. Therefore, this study aimed to investigate if the diet of the Malaysian population is healthy and sustainable. This is a cross sectional study using dietary data generated from food frequency questionnaires (FFQ). The carbon footprint data were linked with the food items/ food groups in the FFQ. The nutrients of the participants’ diet were computed and the proportions of those who met the recommended nutrients intake were established. Contribution of carbon footprint for different food groups and total carbon footprint for each participant’s diet were computed and expressed as kgCO₂eq. Comparison of carbon footprint from participants’ diets between age, sex and ethnicity were carried out. A total of 4825 participants were included in the analysis. Majority were Malays (66.4 %), females (84.0%), married (80.0%) and in the age groups of 30s to 40s (68.8%). The mean total energy intake was 2485+1000 kcal/day. Only 40 to 60% of all participants achieved the Malaysia Recommended Nutrient Intake (RNI) for calcium and less than half of the female participants who were aged 50 years and below fulfilled the RNI for iron. The most commonly consumed food groups were vegetables (270g/day), wheat, rice, fruits, sugar, seafood, poultry, legumes, snacks, milk and beef (46g/day). Total carbon footprint from the participants’ diets were 2.96 kgCO₂eq/day, with the highest contributions of carbon footprint from rice, vegetables, beef, sugar, other cereals, poultry, seafood, wheat, milk, fruits, legume and snacks. Subgroups such as males, Malays and younger participants were more likely to consume diets with higher carbon footprint, compared to their counterparts. The participants’ diet was low in carbon footprint and environmentally friendly, however the quality of diet may need to be improved. Education measures should be targeted for all population and specifically for the sub-groups that consumed diets with higher carbon footprint.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

In this study, I extend the Fama and French five-factor asset pricing model with a sixth factor, namely, carbon risk, to investigate its impact on equity returns. To measure carbon risk, a new factor ‘pollutant minus green,’ is developed using the difference between the weighted average returns of pollutant and green firms across 51 developed and emerging countries across four categories—North America, Europe, Emerging Markets, and the Asia Pacific. The results reveal that North America, Europe, and Asia Pacific markets have a carbon risk premium that gets eliminated in small-cap firms. The carbon risk factor is further tested in left-hand side (LHS) test asset portfolios and found to be more pronounced with size-effect anomaly; specifically, small stock firms report greater declining average returns because of more exposure than the mega-cap stocks to carbon dioxide emissions. Furthermore, size-effect anomaly prevails with profitability and investment factors across firms. Therefore, high profitability, as well as high investment small firms, show a greater decline than the big stock firms in average returns when their carbon dioxide emissions increase. The asset pricing model evaluation is carried out through the Gibbons, Ross, and Shanken test. The six-factor model directed at capturing carbon risk patterns in average equity returns performs better than the three-factor and five-factor models of Fama and French (1993 and 2015) in the majority of categories under 3x3 sorting and compete with both Fama and French model under 2x4x4 sorted LHS portfolios. The finding of this study offers various useful applications for investors, policymakers, brokers, corporations, governmental pollution abatement institutions, and other stakeholders who wish to obtain carbon risk premium.