As a crucial part of head protection equipment, research on the material and structural application of helmet liners has always been a hot topic in the field of helmet manufacturing. This paper aims to introduce the most common helmet liner materials, including traditional polystyrene, polyethylene, polypropylene, and others, as well as emerging materials such as anisotropic materials, and polymer nanocomposites. In addition, the design principles of helmet liner structure are discussed, including the evolution of multi-layer structure, integration of geometric irregular bubbles, etc., to enhance energy absorption capacity. Advanced manufacturing processes such as additive manufacturing technology are introduced to fabricate complex structures. Finally, the application of biomimetic structures in helmet liner design is explored. For example, the structure of biological tissue can be used to design a helmet liner structure with superior energy absorption performance. On this basis, the idea of bionic structures is extended to the combination of plant stalks and animal skeletal structures, and additive manufacturing technology is used to significantly reduce energy loss during elastic yield energy absorption, thus designing a reusable helmet. This provides a promising research direction for future helmet liner materials and structural applications.

This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

The manuscript presents the use of three novel technologies for the implementation of wireless green battery-less sensors that can be used in agriculture. The three technologies, namely additive manufacturing, energy harvesting, and wireless power transfer from airborne transmitters carried from UAVs, are considered for smart agriculture applications. Additive manufacturing is exploited for the implementation of both RFID based sensors and passive sensors based on humidity sensitive materials. A number of energy-harvesting systems at UHF and ISM frequencies are presented which are in position to power platforms of wireless sensors, including humidity and temperature IC sensors used as agriculture sensors. Finally, in order to provide the wireless energy to the soil-based sensors with energy harvesting features, wireless power transfer (WPT) from UAV carried transmitters is utilized. The use of these novel technologies can facilitate the extensive use and exploitation of battery-less wireless sensors which are environmentally friendly and thus “green”. Additionally, it can potentially drive precision agriculture in the next era, through the implementation of a vast network of wireless green sensors which can collect and communicate data, to airborne readers so as to support with data the Artificial Intelligence and Machine Learning based, decision making platforms.

In the past few years, cloud-based additive manufacturing has shown its application and potential in industries. For this reason, when the demand for cloud-based additive products increases, efficient scheduling of related tasks becomes more important to achieve optimized duration. This research proposes a Heuristic Scheduling Algorithm (HSA) for use in Cloud-Based Additive Manufacturing (CBAM) with an approach to Critical Chain Buffer Management (CC/BM). This research aims to schedule and optimize the time in cloud-based additive manufacturing, in addition to the parts production process, it also includes the steps of receiving online orders and informing the manufacturing unit and sending them to the customer. The HSA proposed in this research consists of three phases 1- Buffer sizing, 2- Additive manufacturing and logistics scheduling, and 3- Buffer controlling. To evaluate, the performance of the algorithm is simulated. The finding shows that the proposed HAS can effectively solve the CBAM scheduling problem.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

In the article, the results of research on a NiTi alloy with a high nickel content (51.7 at.%), produced using the additive technology SLM method and subjected to isothermal aging after so-lution annealing, are presented. The study involved the determination of the sequence of phase transformations occurring using differential scanning calorimetry (DSC), and the determination of the temperature range of these transformations. In parallel, the phase composition was determined using the XRD method; hardness and the Young’s modulus were also determined. The analysis of the DSC results obtained indicates the following characteristic features of the NiTi alloy, which change with ageing time: (1) during cooling (from +1500C to -500C), the type of transformation changes from a one-step transformation after solution annealing to a two-step transformation after the ageing process over 1, 20 and 100 hours at 500°C; (2) during heating (from -500C to +1500C) for all the samples, regardless of the ageing time, only a one-step transformation from martensite M(B19’) to austenite A(B2) is observed; (3) the temperature at which the transformation starts increases with the ageing time, (4) the width of the total temperature range of the transformation M(B19’)  A(B2) during heating changes from large (∆T=49,7°C), after solution annealing, to narrow (∆T=19.3°C and ∆T=17.9°C after 20 h and 100 h of ageing) and, most importantly, (5) a comparison with literature data shows that, irrespective of the composition of the NiTi alloy and the manufacturing technology of the alloy samples (regardless of the fact whether this was traditional or additive technology), a sufficiently long ageing process period leads to the occurrence of the martensite  austenite transformation in the same temperature range.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

Additive manufacturing (AM) or 3D printing of metals is gaining popularity due to its flexibility in fabricating parts with highly complex designs, as well as simplifying manufacturing steps and optimizing process times. In this investigation, 17-4 PH stainless steel was additively manufactured using Laser-Powder Bed Fusion (L-PBF), followed by functionalization through a DUPLEX treatment. This treatment involved a plasma-assisted nitriding process, followed by deposition of an arc-PVD c-Al0.7Cr0.3N hard coating. The microstructural modifications resulting from plasma nitriding (such as the formation of Fe2,3N and Fe4N, and the αN or expanded martensite phases), and the surface improvements with the c-Al0.7Cr0.3N coating on the 3D-printed 17-4 PH steel, are evaluated in comparison to conventionally manufactured 17-4 PH steel. These microstructural characteristics are correlated with the mechanical response of the treated surfaces. As a result of the plasma nitriding process, the hardness of the 3D-printed 17-4 PH SS increased by approximately 260%. The wear, measured through dynamic and static scratch-testing, was reduced by approximately 31%. This improvement was attributed to the modification of adhesive failure mechanisms, leading to a reduction in wear volume, improved coating adhesion, and enhanced scratch resistance.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Additive manufacturing (AM) has revolutionized the field of biopolymers by providing a range of opportunities to create complex and intricate structures. Here we provide an overview of developments in biopolymer AM, first in the context of how natural systems have impacted the synthetic processes of AM, and secondly in the context of how synthetically derived structures can be used for biomedical applications. In particular, we explore the range of biopolymers developed for AM, AM techniques for biopolymers, and potential biocompatible medical applications with a focus on four categories of tissue in the human body: skin, bone, heart, and nerve. Despite the current challenges of the technology, exciting results in tissue regeneration, synthetic replacements for natural grafts, and complex dynamic organoids have already come to pass - with many more possible in the future.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Sub-micro dislocation cellular structures formed during rapid solidification break the strength-ductility trade-off in laser powder bed fusion (LPBF)-processed 316L stainless steel through high-density dislocations and segregated elements or precipitates at the cellular boundaries. The high-density dislocation entangled at the cellular boundary accommodates solidification strains among the cellular structures and cooling stresses through elastoplastic deformation. Columnar grains with cellular structures typically form along the direction of thermal flux. However, the ultra-low misorientations between the adjacent cellular structures and their interactions with the cellular boundary formation remain unclear. In this study, we revealed the ultra-low misorientations between the cellular structures in LPBF-processed 316L stainless steel using conventional electron backscatter diffraction (EBSD), transmission Kikuchi diffraction (TKD), and transmission electron microscopy (TEM). The conventional EBSD and TKD analysis results could provide the misorientation angles smaller than 2° while the resolution mainly depends on the specimen quality and scanning step size, and so on. TEM technique with higher spatial resolution provides accurate information between adjacent dislocation cells with misorientation angles smaller than 1°. This study presents that TEM method is the better and more precise analysis method of the misorientation measurement of the cellular structures and provides insights into measuring the small misorientation angles between adjacent dislocation cells and nanograins in nanostructured-metals and alloys with ultrafine-grained microstructures.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

We explore 3D printing modules for self-assembling spacecraft and robots – structure, actuators, electrics. Self-assembly has long been viewed as a highly desirable capability for autonomous construction of large space structures. We review self-assembly in space which focusses on the self-assembly of modules that demonstrate the range of applications. However, self-assembly may be synergised with 3D printing to offer an automated capability from raw material to modules for assembling new spacecraft or habitats. One application of 3D printing is using space debris on-orbit as an in-situ resource - defunct spacecraft may be salvaged as raw material for in-situ construction on demand. The common features of all self-assembling modules are that the modules constitute a structure housing a computer-controlled actuator internally and a reversible latching mechanism externally. We have demonstrated a 3D printed DC electric motor in which the only components that were not 3D printed are the wire coils. We have married our 3D printed motor prototype as an actuated joint between two 3D printed trigon-type panels developed as part of a trigon self-assembling system concept. The trigon concept underlies a modular approach to self-assembling and self-deploying structures. The 3D printed motorised panel system demonstrates that the motor aspect and structural aspects of robotic self-assembling machines are amenable to 3D printing. This has implications for self-assembling systems into modular satellites as a solution to space debris.

To stabilize the Earth’s climate a large-scale transition is needed to non-carbon emitting renewable energy technologies like wind and solar energy. Although these renewable energy sources are now lower-cost than fossil fuels, their inherent intermittency make them unable to supply a constant load without storage. To address these challenges rechargeable electric batteries are currently the most promising option; however, their high capital costs limit current deployment velocities. To both reduce the cost as well as improve performance 3D printing technology has emerged as a promising solution. This literature review provides the state-of-the-art enhancements of battery properties with 3D printing including efficiency, mechanical stability, energy and power density, customizability and sizing, production process efficiency, material conservation and environmental sustainability as well as the progress in solid-state batteries. The principles, advantages, limitations, and recent advancements associated with the most common types of 3D printing are reviewed focusing on their contributions to the battery field. 3D printing batteries offer design flexibility, material flexibility, reduces pack weight, minimizes material waste, increases the range of applications and has the potential to reduce costs. As 3D printing technologies become more accessible, the prospect of cost-effective production for customized batteries is extremely promising.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

17-4PH steel is a widely used grade for precipitation hardening. The growing demand for modern materials with high corrosion and tribological resistance has led to its increased use for the production of medical devices. With additive manufacturing (AM), complex functional shapes can be achieved for medical applications. Direct laser metal sintering (DMLS) technology makes it possible to obtain products with complex architectures, but it also faces various challenges, including imperfections in the surface layer of products due to the use of 3D printing technology itself. This study analyzed the abrasive wear resistance in 0.9% NaCl solution of 17-4PH steel produced by DMLS technology. In order to improve the properties of the surface layer after 3D printing and to improve the tribological wear resistance of the steel, a shot peening (SP) process using CrNi shot and ceramic beads (based on ZrO2) was applied. The chemical and phase composition of the materials obtained, Vickers hardness, surface roughness, and microscopic and SEM imaging were investigated. Tribological tests were carried out using the ball-on-disc method, and the surfaces that showed traces of abrasion to identify wear mechanisms were subjected to SEM analysis. The chemical composition was in accordance with the EOS manufacturer's declarations, and the presence of austenite and martensite was found in the post-production state, while a higher content of martensitic phase was found in the case of peened samples due to phase transformations. The surface hardness of the peened samples increased more than twice, and the post-treatment roughness increased by 12.8% after peening CrNi steels and decreased by 7.8% after peening ZrO2 relative to reference surfaces. Roughness has an identifiable effect on sliding wear resistance. Higher roughness promotes material loss. After the SP process, the coefficient of friction increased by 15.5% and 20.7%, while the wear factor (K) decreased by 25.9% and 32.7% for the samples peened with CrNi steels and ZrO2, respectively. Abrasive and adhesive mechanism were dominant featured with slight fatigue. The investigation showed a positive effect of SP on the tribological properties of DMSL 17-4PH.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

The space shuttle, a revolutionary spacecraft that has played a significant role in human space exploration, was composed of various advanced materials that were carefully selected to meet the extreme demands of spaceflight. This review paper provides a comprehensive examination of the materials historically employed in the construction of space shuttles and explores the latest trends shaping the field. The evolution of space shuttle materials is traced from the inception of the space program to contemporary missions, highlighting key milestones, challenges, and breakthroughs. Emphasis is placed on the critical role that materials play in the overall performance, safety, and sustainability of space shuttles. The paper begins by elucidating the diverse requirements that materials must fulfill in the harsh and complex environment of space, encompassing extreme temperatures, radiation exposure, and mechanical stresses. A detailed analysis of the materials utilized in the fabrication of various shuttle components, such as thermal protection systems, structural elements, and propulsion systems, is presented. Special attention is given to the challenges posed by re-entry and the strategies employed to mitigate heat-related issues. Furthermore, the review explores recent innovations and emerging materials that are reshaping the landscape of space shuttle design. Advancements in nanotechnology, composite materials, and additive manufacturing are discussed in the context of their potential applications for enhancing shuttle performance and reducing mission costs. The paper also addresses the importance of sustainability in space exploration, exploring materials with lower environmental impact and improved recyclability. The review concludes with a forward-looking perspective on the future of materials, considering ongoing research, development, and the potential incorporation of cutting-edge technologies. Insights are provided into how the evolving landscape of materials science may influence the design and manufacturing processes of the next generation of space vehicles. This paper provides an overview of the materials used in the construction of the space shuttle, including their properties, applications, and challenges. The materials used in the space shuttle are critical in ensuring the safety, performance, and longevity of the spacecraft, and understanding their characteristics and performance in space is crucial for the advancement of aerospace engineering.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

The terrain of Changbai Mountain has great influence on the distribution of atmospheric flows and the occurrence and development of precipitation. This study quantitatively analyzes the regional characteristic of topographic perturbations and the relationship between terrain, wind and precipitation in Changbai Mountain region, by using a spectral analysis of the two-dimensional discrete cosine transform. Three domains with relatively heavy summer precipitation are selected as the study region. The results indicate that the overall terrain of Changbai Mountain region exhibits anisotropic characteristics. The terrain spectra of domain B are less than those of domain A and C across the whole wavelength (λ) bands, indicating that the large-scale topographic perturbations of domain B are relatively weak. The largest topographic spectral peak of domain C shows the most pronounced undulation of terrain among the three domains. The dominant wavelengths of terrain height variance for domain A and C, both close to the respective maximum wavelengths, indicate more prominent large-scale topographic perturbations. For domain A, the variation of the precipitation spectra is consistent with that of the wind spectra at the wavelength bands of λ < 390 km, showing a high correlation between wind field and the occurrence of rainfall. The inverse relationship at larger wavelengths indicates that multiple factors contribute to the occurrence of rainfall. For domain B, there is consistency in the fluctuations of terrain spectra, precipitation spectra, and wind spectra at the wavelength bands of λ < 278.3 km, implying that the smaller-scale terrain has an important effect on the occurrence of summer precipitation. For domain C, the variations of terrain spectra, precipitation spectra, and wind spectra are almost consistent across the whole wavelength bands, indicating that the large-scale terrain and minor terrain both play a crucial role in atmospheric uplift and the occurrence and development of summer rainfall.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

Human exposure to foodborne inorganic nanoparticles (NPs) is a growing concern. However, identifying potential hazards linked to NP ingestion often requires long-term exposure in animals. Owing these constraints, intestinal organoids are a promising alternative to in vivo experiments, as such an in vitro approach should enable rapid and reliable assessment of the effects on the gut of ingested chemicals. However, this remains to be validated for inorganic substances. In our study, a transcriptomic analysis and immunofluorescence staining were performed to compare the effects of food-grade TiO2 (fg-TiO2) on enteroid-derived monolayers (EDMs) from murine intestinal organoids to known impacts of TiO2 on intestinal epithelium. After validating their ability to dose-dependently respond to a pro-inflammatory cytokine cocktail, EDMs were exposed to 0.1, 1 or 10 µg fg-TiO2/mL for 24h. In line with known data, a dose-related increase of muc2, vilin 1 and chromogranin A gene markers of cell differentiation was observed. In addition, fg-TiO2 induced apoptosis and dose-dependent genotoxicity, while a decreased expression of genes encoding for antimicrobial peptides, and of genes related to tight junction function was observed. These results validated the use of EDMs as a reliable model for toxicity testing of foodborne NPs likely to affect the intestinal barrier.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Having garnered significant attention in the scientific community over the past decade, Wire Arc Directed Energy Deposition (arc-DED) technology is at the heart of this investigation into additive manufacturing parameters. Singularly focused on invar as the selected material, the primary objective revolves around devising an indirect cord height measurement approach. This innovative methodology involves the seamless integration of internal signals and sensors, enabling the derivation of crucial measurements sans the requirement for direct physical interaction or conventional measurement methodologies. Through the course of this research, meticulous alteration of deposition parameters is undertaken to thoroughly scrutinize their influence on the ultimate cord dimensions. The fusion of cutting-edge manufacturing techniques with advanced sensor technology constitutes the essence of this endeavor, offering substantial potential to augment precision and efficiency in additive manufacturing processes. Remarkably cost-effective, this solution circumvents the need for intricate measurements and significantly contributes to the proper layer-by-layer growth process.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

CubeSats, known for their compact size and cost-effectiveness, have gained significant popularity. However, their limited size imposes restrictions on optical aperture and, consequently, Ground Resolution Distance in Earth Observation missions. To overcome this limitation, the concept of deployable optical payloads with segmented primary mirrors which can unfold like petals has emerged, enabling larger synthetic apertures and enhanced spatial resolution. This study explores the potential benefits of leveraging Additive Manufacturing (AM) and Topology Optimization (TO) in the realm of ultra-precision machining, specifically single point diamond machining. The goal is to reduce fixture weight while improving stiffness to minimize deformations caused by rotational and cutting forces which compromise optical performance. Through Finite Element Analysis, this research compares conventionally machined fixtures with those produced using AM and TO techniques. The results reveal that concept designs created through TO can achieve a remarkable 68% reduction in weight. This reduction makes the assembly, including the machining fixture and 12U deployable segments, manageable by a single operator without the need for specialized lifting equipment. Moreover, these innovative designs lead to substantial reductions of up to 86% and 51% in deformation induced by rotational and cutting forces, respectively.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

Biological control, a well-established plant protection method, has garnered substantial attention in recent decades. Various approaches, including biological control agents (BCA), catch crops, biofumigation, sticky traps, and pheromones, have been extensively explored. While the effectiveness of these methods varies depending on specific circumstances, their collective significance has grown amid mounting pressures to curtail or eliminate conventional synthetic plant protection products. Previous review articles have highlighted the synergistic benefits of using two or more BCAs simultaneously, yet limited information exists regarding the concurrent use of diverse biological control methods. This comprehensive review incorporates a thorough literature search to assess the synergistic potential of concurrently employing two or more of these methods, followed by a discussion on perspectives of holistic management and mimicking of complex natural systems, shedding light on the vast potential and need for further research in this domain.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

Vibration monitoring is a critical aspect of assessing the health and performance of machinery and industrial processes. This study explores the application of machine learning techniques, specifically the Random Forest (RF) classification model, to predict and classify chatter—a detrimental self-excited vibration phenomenon—during machining operations. While sophisticated methods have been employed to address chatter, this research investigates the efficacy of a simplified RF model. The study leverages simulated vibration data, bypassing resource-intensive real-world data collection, to develop a versatile chatter detection model applicable across diverse machining configurations. The feature extraction process combines time-series features and Fast Fourier Transform (FFT) data features, streamlining the model while addressing challenges posed by feature selection. By focusing on the RF model’s simplicity and efficiency, this research advances chatter detection techniques, offering a practical tool with improved generalizability, computational efficiency, and ease of interpretation. The study demonstrates that innovation can reside in simplicity, opening avenues for wider applicability and accelerated progress in the machining industry.

Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

Biocomposite membranes based on polylactic acid (PLA) and cellulose nanocrystals (CNCs) were developed using a scientific approach. Dicumyl peroxide (DCP) was used as a polymerization ini-tiator, while tin octoate (Sn(Oct)2) and triphenylphosphane (P(C6H5)3) were used as catalysts. A torque rheometer was used to mix the components of the biocomposite, and thin films was prepared by solvent casting. Fourier transform infrared (FTIR) spectroscopy confirmed the coupling between the PLA and CNCs. Field emission scanning electron microscopy (FESEM) showed that the CNCs were well-dispersed in the PLA matrix with an unimodal particle size distribution and a maximum particle size of around 200 nm. Thermogravimetric analysis (TGA) and differential scanning calo-rimetry (DSC) analysis demonstrated good thermal stability and improved biodegradability of the biocomposite membrane compared to pure PLA. Mechanical characterization showed a Young's modulus of 1.65 GPa, which is comparable to that of other composite materials, and a maximum tensile strength of 20.31 MPa, which is higher than that of pure PLA. These results suggest that the developed biocomposite membrane has potential applications in water filtration, food packaging, and biomedical devices.

In this study, an optimized multi-material system was designed and developed to print samples in various applications, including biomedical fields (e.g., mandibular bone loss). To improve the mechanical and biological properties of scaffolds utilized for dental bone loss applications, a multi-material setup was devised, which employs digital light processing technology. This setup consists of a linear system comprising two resin vats and one ultrasonic cleaning tank, enabling the integration of diverse materials and structures to optimize the composition of the scaffold. This approach was used to print multi-material PLLA scaffolds containing 20 wt.%. HA on the interior side, and PLLA containing 1 wt.% GO on the exterior surface of the scaffold, which were evaluated mechanically and biologically after printing. The scaffold was designed using a triply periodic minimal surface (TPMS) lattice structure, which is known to possess favorable mechanical and biological properties. Various multi-material samples were successfully printed and evaluated to illustrate the multiple-material setup's potential for ensuring proper function, cleaning, and adequate interface bonding. By numerically evaluating several TMPS structures, a novel Gyroid TPMS scaffold with a nominal porosity of 50% was developed and validated experimentally. The biological properties of the scaffolds were also evaluated, including surface morphology, (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) MTT assay, and cell adhesion. Based on the results, multi-material components with the least contaminations with suitable mechanical and biological properties were successfully printed. By combining PLLA-HA and PLLA-GO, this innovative technique holds tremendous potential for enhancing the effectiveness of regenerative procedures in the field of dentistry.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

The widespread use of epoxy resin (ER) in industry, owing to its excellent properties, aligns with the global shift toward greener resources and energy-efficient solutions, where utilizing metal oxides in 3D printed polymer parts can offer extended functionalities across various industries. ZnO concentrations in polyurethane acrylate composites impacted adhesion and thickness of DLP samples, with 1 wt.% achieving a thickness of 3.99±0.16 mm, closest to the target thickness of 4 mm, while 0.5 wt.% ZnO samples exhibited the lowest deviation in average thickness (±0.03 mm). Tensile strength in digital light processed (DLP) composites with ZnO remained consistent, ranging from 23.29 MPa (1 wt.%) to 25.93 MPa (0.5 wt.%), with an increase in ZnO concentration causing a reduction in tensile strength to 24.04 MPa and a decrease in the elastic modulus to 2001 MPa at 2 wt.% ZnO. The produced DLP samples, with their good corrosion resistance in alkaline environments, are well-suited for applications as protective coatings on tank walls. Customized DLP techniques can enable their effective use as structural or functional elements, such as in Portland cement concrete walls, floors and ceilings for enhanced durability and performance.

Life Cycle Assessment (LCA) is a technique developed to measure possible environmental impacts during the manufacture and use of a given product or service. Additive Manufacturing (AM) has proven to be suitable in several industries, especially wire and arc additive manufacturing (WAAM), offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and equivalent CO₂ emissions (CO₂e). This study aimed to develop a methodology to evaluate environmental indicators during the life cycle assessment, from gate-to-gate, in the production of two low-alloy carbon steel metal parts (flanges) using ER-90 wire and allowed identifying the main stages that most influence environmental indicators. The total energy consumption in the production of flanges 1 and 2 were, respectively, 10,239.0 MJ, 12,754.0 MJ and the total carbon footprint, respectively, 714.1 kgCO₂e kg^-1 and 749.3 kgCO₂e kg^-1.

The study conducts a comparative life cycle assessment (LCA) analysis to assess the environmental impact of two different manufacturing processes used to produce transparent dental aligners. The former method consists of thermoforming a polymeric disc over 3D printed, customized models, while the second, more innovative approach involves the direct printing of aligners using additive manufacturing (AM), specifically applying digital light processing (DLP) technology. The analysis results highlight how adopting direct printing through AM brings significant advantages in terms of environmental sustainability, thanks to the substantial reduction in raw materials and electricity consumption. These drops translate into decreased potential environmental impacts across all impact categories considered within the EF 3.1 method. Furthermore, lowering the amount of raw materials needed in the direct printing process contributes to a notable decrease in the overall volume of waste generated, emphasising the environmental benefits of this innovative technique.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

This article addresses the need to know the thermal conductivity in different filaments that this FDM technology uses. Because there are multiple applications that these additive manufacturing products play in the field of thermal insulation. For the study of thermal conductivity, the DTC-25 commercial conductivity measurement bench is used, where the tests will be carried out on a set of seven different materials with 100% fabrication density. From base materials such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA), materials of high mechanical and thermal resistance, polyether ether ketone (PEEK) and high-performance polyetherimide thermoplastic (ULTEM), to materials with metal inclusions (aluminum 6061) that would later be subjected to thermal aftertreatments. The study shows how the parts manufactured with aluminum inclusion have a higher thermal conductivity, 0.40 ±0.05 W/m·K, compared to another material, such as TPU, of high mechanical and thermal resistance, with a conductivity of 0.26 ±0.05 W/m·K.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

Material Extrusion is a popular additive manufacturing technology due to its low cost, wide market availability, ability to construct complex parts, safety, and cleanliness. However, optimizing the process parameters to obtain the best possible mechanical properties has not been extensively studied. This paper aims to develop ensemble learning-based models to predict the ultimate tensile strength, Young's modulus, and strain at break of PLA and PLA-CF 3D-printed parts, using printing temperature, printing speed, and layer thickness as process parameters. Additionally, the study investigates the impact of process parameters and material selection on the mechanical properties of the printed parts and uses Genetic Algorithms for multi-objective optimization according to user specifications. The results indicate that process parameters and material selection significantly influence the mechanical properties of the printed parts. The Genetic Algorithm successfully identifies optimal parameter values for the desired mechanical properties. Moreover, this work is the first to model Process-Structure-Properties relationships for an additive manufacturing process and to use a multi-objective optimization approach for multiple mechanical properties, utilizing ensemble learning-based algorithms and Genetic Algorithms.

This study presents the manufacturing process driven development of an interlocking metasurface mechanism (ILM) for Fused Filament Fabrication (FFF) with a focus on open-source accessibility. The presented ILM is designed to enable strong contact between to planar surfaces. The mechanism consists of spring elements and locking pins which snap together when forced into contact. The mechanism is designed to optimize mechanical properties, functionality and printability with common FFF printers. The mechanisms is printed from thermoplastic polyurethane (TPU) filament which was selected for its flexibility, crucial for spring element performance and tolerances of the fabrication method. To characterize the designed mechanism a tensile test is carried out to assess the holding force of the ILM. The force-displacement profiles are analyzed and categorized into distinct phases, highlighting the interplay between spring deformation, sliding, and disengagement. The results show variations in holding forces attributed to geometric and material-related factors. The testing results are compared and discussed to a numerical simulation carried out with a frictionless approach with a nonlinear Neo–Hookean material law. The study underscores the importance of meticulous parameter control in 3D printing for consistent and reliable performance of interlocking metasurface mechanisms. The investigation leads to a scalable model of a ILM element pair with a distinct three-phase snapping characteristics ensuring reliable holding capabilities.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

We introduce a new generalized inverse (i.e., generalized EP element) which is a natural generalization of EP and *-DMP elements in a Banach *-algebra. We present polar-like characterizations of generalized EP elements. The necessary and sufficient conditions under which the sum of two generalized EP elements is a generalized EP element are investigated. Finally, the generalized core-EP orders for generalized EP elements are characterized.

The paper delves into an extensive exploration of the integration of the circular economy paradigm within the realm of additive manufacturing (AM). The objective is to comprehensively investigate existing methodologies for structuring the symbiotic relationship between circular economy and additive manufacturing, while meticulously analyzing the current research gap concerning the implementation of circular economy principles in additive manufacturing practices. A thorough review focusing on the sustainability of additive manufacturing within the circular economy framework was conducted. This review aims to recognize and delineate pertinent aspects related to post-use material valuation in AM, recyclability of materials, and the environmental footprint associated with these processes. Emphasis was placed on the significance of examining circular economy facets concerning additive manufacturing processes to establish a holistic understanding. The overarching goal of this review is to augment knowledge regarding the potential advantages and benefits derived from the seamless integration of circular economy principles within AM. By elucidating the activities essential to attain compliance with the Sustainable Development Goals, this study endeavors to illuminate the pathway toward promoting sustainable development through the harmonious marriage of additive manufacturing and the circular economy.

The recent decade has witnessed the evolution of a novel paradigm of alloying which is based on utilising multiple elements to design compositionally complex alloys also known as high entropy alloys (HEAs). Conventional manufacturing of HEAs has a number of drawbacks, especially in terms of mechanical properties and design complexities. This has been addressed by additive manufacturing (AM), which has not only led to the fabrication of complex-shaped HEA components but has also enabled both ex-situ and in-situ tailoring of alloy microstructures. Considering the increasing interest in AM-based fabrication of HEAs in the last ten years, the present chapter is aimed at highlighting the present status and challenges in the avenue of AM of HEAs. This has been followed by a discussion on the recent trends in the avenue of AM-based fabrication of HEAs from the viewpoints of (i) microstructure evolution and mechanical properties, and (ii) alloy fabrication techniques. The chapter ends with a discussion on the future prospects in the aforementioned avenue.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

Additive manufactured interlocking structures often face challenges in achieving suitable joinability due to thermal deformation. This issue becomes particularly interesting when fabricating structures that require high density but not fully connected layers, such as soft-magnetic materials. This study focuses on systematical investigation of the deformation as a function of finger thickness and building direction in model interlocking structure. In the perpendicular direction to the build plate, the distortions of joint part were significantly reduced due to lower thermal stress. In addition, the effect of laser power and scan speed on interlocking structure are systematically discussed. Additionally, through stress and thermal simulations of additive manufacturing process, it was confirmed that the compensated model can enhance the joinability of interlocking structures. These findings contribute to the development of optimal design for additive manufactured parts of soft magnetic materials such as stators in electric motor components, which needs insulations and density.

The solved research problem is oriented to the implementation of advanced methods of component design and their sophisticated use in the ever-advancing additive manufacturing. Based on the stated objectives, the research was divided into several parts. Initially, the methods and principles of design in additive manufacturing were evaluated and investigated, from which the intent was subsequently defined and the DfAM method in the component design and development process was determined. The given design method, namely topology optimization (TO), was applied to multiple development and production cycles of additive manufacturing parts to validate the research conclusions. In this paper, the procedure for a specific part or component assembly is shown. By evaluating the developed design procedure using the TO method included in the design process, the conclusions are positive in terms of both time savings and properties of the designed part such as strength and weight parameters. The given findings need to be further developed by implementing on specific product lines for increasing the efficiency of the developed design methodology.

The changes in consumer lifestyles have raised awareness of the variety of food options and packaging technologies. Active and smart packaging represents an innovative technology that serves to enhance the safety and quality of products. Smart packaging, as a subset of this technology, entails the integration of additives into packaging materials, thereby facilitating the preservation or extension of product quality and shelf life. This technological approach stimulates a heightened demand for safer food products with prolonged shelf life. Active packaging predominantly relies on the utilization of natural active substances. Therefore, the combination of active substances has a significant impact on the characteristics of active packaging particularly on polymeric blend like Polylactic acid (PLA) as a matrix. So, This review will summarize and explains how the addition of natural active agents influenced the properties related to the performance of active packaging through systematic analysis, providing new insights about the relationship between the types of active agents on physical-mechanical properties, bacterial colony reduction, and applications in foods packaging such as meat, fish, fruit, and vegetables. Through their integration, the market for active and smart packaging systems is expected to have a bright future.

Extrusion-based additive manufacturing (AM) technologies (i.e., fused filament fabrication, FFF) mostly produce thermoplastic parts. However, producing metallic or ceramic parts by FFF is also a sintered-based AM process. FFF for metallic parts can be divided into five steps: (1) raw materials selection and feedstock mixture (including palletization), (2) filament production (extrusion), (3) production of AM components using the filament extrusion process, (4) debinding, and (5) sintering. These steps are interrelated, where the parameters interact with the other ones and have a key role in the integrity and quality of the final metallic parts. FFF can produce high-accuracy and complex metallic parts, potentially revolutionizing the manufacturing industry and taking AM components to a new level. In the FFF technology for metallic materials, material compatibility, production quality, and cost-effectiveness are the challenges to overcome to make it more competitive compared to other AM technologies, like the laser processes. This review provides a comprehensive overview of the recent developments in FFF for metallic materials, including the metals and binders used, the challenges faced, potential applications, and the impact of FFF on the manufacturing (prototyping and end parts), design freedom, customization, sustainability, supply chain, among others.

This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

Three-dimensional (3D) and four-dimensional (4D) printing emerged as the next generation of manufacturing techniques, spanning several research areas such as engineering, chemistry, biology, computing, and materials science. Three-dimensional printing allows the manufacture of complex shapes with high precision, by adding layer by layer of different materials. The use of smart materials that change shape or color, produce an electrical current, become bioactive, or perform an intended function in response to an external stimulus. Shape memory materials (SMMs) in 3D printing technology have attracted a lot of attention due to their ability to respond to external stimuli, leading this technology towards an emerging area of research, "4D printing technology." The core part of this review summarizes the effect of the main external stimuli on 4D textile materials followed by the main applications 4D printed textiles can change their shape over time due to external stimuli such as temperature.

Engine oil degradation and tribological properties are strongly interrelated. Hence, understanding the chemical processes resulting in additive depletion and degradation products is necessary. In this study, in-service engine oils from petrol and diesel vehicles were analyzed with conventional and advanced methods (mass spectrometry). Additionally, the effect of the utilization profile (short- vs. long-range) was studied. Petrol engine oils generally showed accelerated antioxidant and antiwear degradation and higher oxidation, especially in case of a short-range utilization profile, which can be attributed to the higher air-to-fuel ratio (more rich combustion) compared to diesel engines. A detailed overview of oxidation and nitration products, as well as degradation products resulting from zinc dialkyl dithiophosphate and boron ester antiwear additives, diphenylamine antioxidants and salicylate detergents is given. A side-reaction between oxidation products (aromatic carboxylic acids) and the boron ester antiwear is highlighted. This reaction was only detected in the petrol engine oils, where the oxidation products were measured in a high abundance. However, no side reaction was found in the samples from the diesel vehicle, since there the aromatic carboxylic acids were largely absent due to lower oxidation.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

Skeletal muscle is a specialized tissue consisting of nondividing and multinucleated muscle fibers. Skeletal muscle-specific myostatin (MSTN) is a secreted protein that acts as a negative regulator of muscle mass by inhibiting proliferation and differentiation of myoblasts. In this study, we established a screening platform to monitor myostatin promoter activity in rat L8 myoblasts. Extract of Glycyrrhiza uralensis (GUE), an oriental herbal medicine, was identified through this screening platform and, the active fractions of GUE were identified by process-scale liquid column chromatography system. For in vivo study, the GUE as a feed additive was investigated in growth-finishing pigs. The results showed that GUE significantly increased body weight, carcass weight and lean content in pigs. Microbiota analysis indicated that GUE did not affect the composition of gut microbiota in pigs. In summary, this established rodent myoblast screening platform was used to identify a myogenesis-related phytogenic, GUE, and further demonstrated that the active fractions inhibited MSTN expression. These finding suggest a novel application for GUE in growth performance enhancement through modulation of MSTN expression. Furthermore, this established screening platform has great potential for identification and evaluation of a wide variety of phytogenics involving in myogenesis.

(1) The study using the quails of the Manchurian golden breed was aimed at the efficacy of the food supplement based on micro-incapsulated phytase of Obessumbacterium proteus in the recombinant yeast producer Yarrowia lipolytica at a dose of 500 FYT/kg of the feed. (2) The effect of the supplement in the poultry diets on the productivity of young and adult quails was assayed; (3) It was found that the keeping the quails on the diets using the microencapsulated phytase O. proteus provided the highest live weight, the highest intensity of egg production, and the slaughter yield of animals, the lowest feed conversion compared to those in control groups and the groups getting a commercial phytase supplement based on Aspergillus ficuum. Taken together the data obtained in our experiments indicate a high degree of assimilation of phytate-containing products by the quails when using the encapsulated phytase compared to both the control and commercial preparation of phytase of the PhyA class. It can be concluded that it is a highly expedient and promising supplement based on the microencapsulated phytase of class D for feeding, which shows the best kinetic features compared to the phytases of PhyA and PhyC classes when working in the chyme of the poultry.

Metal Additive Manufacturing (MAM) has emerged as a promising technology in the aerospace industry, enabling the production of complex components with enhanced design flexibility and reduced lead times. Concurrently, Industry 4.0 has gained significant attention for its potential to revolutionize aerospace manufacturing processes. The paper aims to cluster and review the literature on MAM in the aerospace industry, specifically focusing on its relevance to Industry 4.0 and its applicability throughout the various stages of the product life cycle for the chief purpose of matching supply with demand. Identified gaps and challenges are analyzed, highlighting the need for further research and outlining research agenda aimed at advancing the integration of MAM for Industry 4.0 in the aerospace sector. By addressing these research areas, the aerospace industry can unlock the value of MAM within an Industry 4.0 framework, leading to improved efficiency, productivity, and competitiveness.

Ledge formation presents a significant challenge in endodontic treatment. Yet, there is still a lack of educational tooth models for hands-on practice. This study aimed to create and evaluate a tooth model for ledge management practice. A natural tooth with curved roots was collected for scientific use under ethics committee approval. Following initial root canal preparation, the tooth was scanned using micro-computed tomography (μCT) and 3D reconstructed. A K-file, created via computer-aided design (CAD), was partly inserted into the root canal wall of the 3D-reconstructed tooth. By subtracting the K-file from the tooth, a tooth model with a root canal ledge was produced. The models were then 3D printed for a hands-on workshop. A seven-item Likert scale questionnaire was administered to 20 postgraduate students and 10 endodontists to assess the model's quality and training effectiveness. The feedback from both students and experts was positive, with no statistically significant differences found between the two groups (p &gt; 0.05). This novel tooth model is expected to address the existing gap in endodontic education and provide benefits for dental practitioners in future applications.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

This comprehensive review explores the advancements in Orthognathic and Oral Maxillofacial Surgery, focusing on the integration of 3D Printing and Virtual Surgical Planning (VSP). Traditional surgical methods, while effective, come with inherent risks and complications, and can lead to variability in outcomes due to the reliance on the surgeon's skill and experience. The shift towards patient-centric care necessitates personalized surgical methods, which can be achieved through advanced technology. The amalgamation of 3D printing and VSP revolutionizes surgical planning and implementation by providing tactile 3D models for visualization and planning, and accurately designed surgical guides for execution. This convergence of digital planning and physical modeling facilitates a more predictable, personalized, and precise surgical process. However, the adoption of these technologies presents challenges, including the need for extensive software training and the steep learning curve associated with computer-aided design programs. Despite these challenges, the integration of 3D printing and VSP paves the way for advanced patient care in orthognathic and oral maxillofacial surgery.

Open-source 3-D printing has played a pivotal role in revolutionizing the additive manufacturing (AM) landscape, by making distributed manufacturing economic, democratizing access, and fostering far more rapid innovation than antiquated proprietary systems. Unfortunately, some 3-D printing manufacturing companies began deviating from open-source principles and violating licenses for the detriment of the community. To determine if a pattern has emerged of companies patenting clearly open-source innovations, this study presents three case studies from the three primary regions of open-source 3-D printing development (EU, U.S. and China) as well as three aspects of 3-D printing technology (AM materials, an open-source 3-D printer, and core open-source 3-D printing concepts used in most 3-D printers). The results of this review have shown that non-inventing entities called patent parasites are patenting open-source inventions already well-established in the open source community and in the most egregious cases commercialized by one (or several) firms at the time of the patent filing. Patent parasites are able to patent open-source innovations by using a different language, vague patent titles and broad claims that encompass enormous swaths of widely diffused open-source innovation space. This practice poses a severe threat to innovation and several approaches to irradicate the threat are discussed.

Artificial intelligence (AI) and 3D printing (3DP) play critical roles in what is known as the 4th Industrial Revolution by developing data- and machine-intelligence-based integrated production technologies. This shift has led to increasingly complex design requirements and fabrication methods, posing several challenges for implementing design, fabrication process, and architectural quality standardization. This paper systematically reviews AI techniques applied in diverse stages of 3DP production in architecture. The research goals are to (1) offer a comprehensive critical analysis of the body of literature; (2) identify and categorize approaches to integrating AI in the production of 3D-printed structures; (3) identify and discuss challenges and opportunities of AI integration in architectural production of 3DP structures; and (4) identify gap and provide recommendations for future research. The findings indicate that topics related to AI applications are current and trending, receiving increasing attention from researchers in general and particularly those working in machine and deep learning, artificial neural networks, and pattern recognition. However, the potential of the application of AI in architectural production using additive manufacturing still needs to be explored. Considering this, the paper emphasizes the necessity of redefining traditional field boundaries and opening new opportunities in the sector.

Investment management is a common process and practice used for achieving a desirable investment goal or outcome. Investment assessment should be carried out at various stages of project realization in accordance with capital investment volume. Investment risk management implies the effective control of all procedures and monitoring of risks in all phases of the investment project. Because of the reason that a single indicator in probability calculation of achieving optimal return from the investment does not exist, performing sufficiently reliable estimates of the quality of investments becomes a tedious task. There are many indicators, factors, and criteria required for consideration to reach the effective solution of the investment problem. Unfortunately, the systematic variation of economic situations in the marketplace stipulates the continuous and frequent changes of investment conditions and environment in which the investor should act and operate. Hence, the rules required for providing a reasonable quality of investment projects can be based only on investor’s management strategy and rely on investor’s intuition and practice. The importance of classification in investment management and decision making process is undeniable. The objects to be classified are described using assessments in accordance with various criteria which can be both quantitative and qualitative. With a competent formulation of the investment process, both methods are used in parallel. There exist various decision making approaches for the investment management, and simple additive weighting (SAW) is one of the well-known multi-criteria decision making (MCDM) methods aiming to provide an optimal decision for decision maker when solving various real-life problems, and particularly, investment problem. In this paper, fuzzy simple additive weighting (FSAW) method in group decision making is applied to undertake the capital investment expenditure for purchasing cars with the purpose of renting them to the public. The development of existing FSAW method is accomplished and this process involves the sensibility of outcomes to changes in the rate of fuzziness represented with decisions taken. Eventually, the degree of fuzziness involved in an analysis that directly attempts to model the immanent vagueness and imperfectness in particular precedency judgments made, is determined. A numerical example illustrates the importance and effectiveness of the suggested approach with the aim of ranking alternatives and hence, determining the most preferred alternative in MCDM problem.

In recent years, there has been a wave of research on complex networks. The purpose of this paper is to study the graph theoretic mathematical properties of random cyclooctatetraene chain. We obtain the explicit analytical expressions for the variances of the Gutman index, Schultz index, multiplicative degree-Kirchhoff index and additive degree-Kirchhoff index of a random cyclooctatetraene chain with $n$ octagons, which plays a crucial role in the research and application of topological indices.

This research focused on the perception of visually impaired individuals regarding tactile image creation using 3D printing. We developed and applied an experiment with 28 participants with visual impairments. They performed tasks based on skills whose foundations are needed and used in their daily lives, such as scanning, tactile discrimination, picture and spatial comprehension. The tactile images used in this study were developed by additive manufacturing and printed over 180 g/m² sulphite paper. The best performances were obtained when (1) the tactile image contour line heights were between 0.2 mm and 0.4 mm; and (2) the texture presented densities between 10% and 50%, when alone, or between 10% and 90%, when combined with another texture. The tested line widths (0.8 mm and 1.2 mm) did not present statistically significant differences in the results. Vision status (low vision or blindness) and moment of vision loss (congenital or late blind) did not influence the results. Schooling affected the activities of identifying objects and locating their copies. In the Conclusion section, there is a detailed recommendation list for the production and application of tactile materials, which range from simplifying forms to encouraging the use of both hands during content assimilation.

(1) Background. Cognitive impairment in people with Multiple Sclerosis (MS) has been studied in relation to some clinical variables (e.g., motor disability and disease duration) and lifestyle fac-tors such as Cognitive Reserve (CR). However, only very few studies have considered the interac-tion of clinical variables and cognitive reserve in preserving the integrity of the neuropsychologi-cal profile. In this paper, we hypothesised that a higher level of CR might predict good cognitive efficiency by modulating the clinical outcome of the disease. (2) Methods. A sample of 100 partic-ipants with MS (age range 30-74), was recruited and assessed remotely with a questionnaire to measure CR and a cognitive screening test. Data were analysed through Generalized Additive Models. (3) Results. We found that the model analysing the interaction between CR and disease duration, and between CR and motor disability was able to explain a significant percentage of cognitive performance. In particular, higher levels of CR predicted better cognitive performance despite long disease duration, unless the motor disability was severe. (4) Conclusion. This study highlights the crucial role of CR in modulating cognitive efficiency in people with MS.

In this paper, the characterization of 3D printed materials that are considered in the design of multirotor unmanned aerial vehicles (UAVs) for specialised purposes was carried out. The multirotor UAV system is briefly described, primarily from the aspect of system dynamics, considering that the airframe parts connect the UAV components, including the propulsion configuration, into a functional assembly. Three additive manufacturing (AM) technologies were discussed, and a brief overview was given of selective laser sintering (SLS), fused deposition modeling (FDM), and continuous fiber fabrication (CFF). Using hardware and related software, 12 series of specimens were produced which were experimentally tested utilizing a quasi-static uniaxial tensile test. The results of the experimental tests are given graphically with displacement-force characteristics. In this work, the focus is on CFF technology and the testing of materials that will be used in the production of mechanically loaded airframe parts of multirotor UAVs. Furthermore, an overview was given in such a way that the specimens were grouped, and the mean values of the maximum stress were presented, so that the tested materials could be more easily compared with conventional materials, such as aluminum alloys.

HIV diagnosis and management have often caused disruptions to the everyday life and imagined futures of people living with HIV, both at individual and social levels. This has been conceptualised, in a rather dystopian way, as ‘biographical disruption’. This paper attempts to re-cast data from interviews with 40 men living with HIV (MLHIV) in Yogyakarta and Belu, Indonesia, in a slightly more positive light. Our analysis uses the concepts of additive and subtractive resilience strategies and we show how, rather than having a purely disrupted biography, participants talked about their experiences of ‘biographical reinvention'. Study participants were recruited using the snowball sampling technique, starting from two HIV clinics in the settings. Data were collected using one-on-one in-depth interviews, and a qualitative framework analysis was used to guide step-by-step data analysis. The findings showed that despite the disruptions in their everyday life (i.e., mental health condition, work, activities, social relationships, etc.) following the HIV diagnosis and management, MLHIV in our study managed to utilise their internal assets or traits (i.e., hope, optimism, resilience) and mobilised external resources (i.e., support from families, friends and healthcare professionals) to cope with the disruptions. An interweaving of these internal assets and external resources enabled them to take on new activities and roles (additive resilience strategies) and give up health compromising behaviours (subtractive resilience strategies). These were effective for most MLHIV in our study not only to cope with the HIV repercussions and improve their physical and mental health conditions, but to think or work on a ‘reinvented’ biography which encompassed resilience, hope and optimism for better health, life and future. The findings indicate the need for HIV interventions and healthcare systems that provide appropriate support for the development and maintenance of internal assets of PLHIV to enable them to cope with the repercussions of HIV and work on a ‘reinvented’ biography.

In recent years, in addition to the commonly known wire-based processes of Directed Energy Deposition using lasers, a process variant using the electron beam has also developed to industrial market maturity. The process offers particular potential for processing highly conductive, reflective or oxidation-prone materials. However, for industrial usage there is a lack of comprehensive data on performance, process limits and possible applications. The present study deals with this problem using the example of the high-strength aluminum bronze CuAl8Ni6. Multi-stage test welds are used to determine the physically possible process limits and draw conclusions about the suitability of the parameters for additive manufacturing. For this purpose, optimal ranges for energy input, possible welding speeds and the scalability of the process were investigated. Finally, additive test specimens in the form of cylinders and walls are produced and the hardness profile, microstructure and mechanical properties are investigated. It is found that the material CuAl8Ni6 can be well processed by wire electron beam additive manufacturing. The microstructure is similar to a cast structure, the hardness profile over the height of the specimens is constant and the tensile strength and elongation at fracture values achieved correspond to the specification of the raw material.

In this study, 3D printing of poly-l-lactic acid (PLLA) scaffolds reinforced with graphene oxide (GO) nanoparticles via Digital Light Processing (DLP) was investigated to mimic bone tissue. Stereolithography is one of the most accurate additive manufacturing method, but the dominant available materials used in this method are toxic. In this research, a biocompatible resin (PLLA) was synthetized and functionalized to serve the purpose. Due to the low mechanical properties of the printed product with the neat resin, graphene oxide nanoparticles in three levels (0.5, 1, and 1.5 Wt.%) were added with the aim of enhancing the mechanical properties. At first, the optimum post cure time of the neat resin was investigated. Consequently, all the parts were post-cured for three hours after printing. Due to the temperature-dependent structure of GO, all samples were placed in an oven at 85 ° C for different time periods of 0, 6, 12, and 18 hours to increase mechanical properties. The compression test of heat treated samples reveals that the compressive strength of the printed parts containing 0.5,1, and 1.5 % of GO increased by 151,162 ad 235%, respectively. Scaffolds with the designed pore sizes of 750 microns and a porosity of 40% were printed. Surface hydrophilicity test was performed for all samples showing that the hydrophilicity of the samples increased with increasing GO percentage. The degradation behavior of the samples was evaluated in a PBS environment, and it revealed that by increasing GO, the rate of component degradation increased, but the heat treatment had the opposite effect and decreased the degradation rate. Finally, besides improving biological properties, a significant increase in mechanical properties under compression can introduce the printed scaffolds as a suitable option for bone implants.

Natural rocks are highly heterogeneous due to various geological processes that constantly alter their properties. The accumulation, deposition, and cementation of mineral and organic particles continuously modify the spatial characteristics of rock properties. Property variability or anisotropy is commonly observed in most rock types and influences strength, transport, and thermal conductivity behavior. This unpredictability presents a significant challenge for laboratory testing. Binder-jet additive manufacturing (3D printing) has emerged as a valuable technology for characterizing rock properties in geoscience and engineering. This study proposes a methodology to evaluate the variability and repeatability of mechanical properties of 3D-printed sandstones during binder-jet additive manufacturing. The mechanical properties were analyzed statistically for samples located in various parts of the 3D printer build volume. The results showed that the 3D-printed sandstones exhibited significant variations in their strength and stiffness properties when measured from samples produced within the same build volume during binder-jet additive manufacturing. The Uniaxial Compressive Strength (UCS) varied from 23 to 38 MPa, with an average value of 29 MPa. The Young's modulus, on the other hand, ranged from 1.5 to 4.05 GPa, with an average value of 2.33 GPa. The variability of the mechanical properties, quantified by the standard deviation, decreased when the entire population of 3D-printed sandstones was divided into smaller samples situated at different elevations of the build platform.

Functionally graded materials (FGM) have attracted considerable attention in the field of composite materials and rekindled interest in research on composite materials, due to their unique mechanical response achieved through material design and optimization. Compared to conventional composites, FGMs offer several advantages and exceptional properties, including improved deformation resistance, improved toughness, lightness properties, and excellent recoverability. This study focused on the production of functionally graded (FG) polymer materials by additive manufacturing (AM) method. FG structures were produced by the Fused Deposition Modeling (FDM) method using Acrylonitrile benzidine styrene (ABS) and Polylactic acid (PLA) materials and tensile tests were performed according to ASTM D638. The effects of different layer thicknesses, volume ratios, and total thicknesses on mechanical behavior were investigated. In addition, tensile tests were carried out by producing single-layer samples at certain volume ratios to create a numerical model with the Finite element method to verify the experimental data. As a result of this study, it is presented that the FG structure produced with FDM improves mechanical behavior.

Nitrate and nitrite are the most extensively used food additives in the food industry for their multifunctional properties, and they have been in the spotlight for decades for its controversial back effects. The conversion of nitrate and nitrite to various nitroso compounds, specifically N-nitrosamine raises the question of the integrity of these additives. Nitrosamine is a well-known carcinogen and mutagen. A large number of studies demonstrate the carcinogenic effects of these salts. Are these findings credible? Nonetheless, the regulatory agencies approve its usage; is it biased? Are we feeding on the carcinogens in processed foods? The current work provides an insight into the basic and toxicological findings of the food additives -nitrate and nitrite.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

The popularity and growth of additive manufacturing(AM) in recent years are due to its ability to provide innovative solutions to complex manufacturing challenges and its potential to transform the way products are designed, developed, and produced. In this work, the numerical simulation geometry of the model extruder from nozzle is established along with the material extrusion process. The high gravity material extrusion system (HG-MEX) properties and characteristics during filament fabrication are evaluated. This work investigates the effects of gravity on the material extrusion process from nozzle extrusion. This work is unique in the incorporation of fluid surface characteristics to represent the performance and contact with the material extrusion in additive manufacturing. The use of simulation in high gravity material extrusion in additive manufacturing is a meaningful and valuable approach to improving the quality and efficiency of the process.

The paper presents the conceptualization and realization of a novel platform for additive manu-facturing, an industrial robot arm-based system for additive manufacturing applications. Tradi-tional 3D printers, especially those employing fused deposition modelling (FDM) processes, are restricted to depositing material in a single toolpath plane (e.g. x-y plane). The focus of this study was to explore the feasibility of integrating commercial off the shelf (COTS) additive manufac-turing technologies with a six degree of freedom industrial robot arm to yield a 3D additive manufacturing system with the capability to perform free-form six degree of freedom fused deposition modelling. The present paper presents the development of a platform from stage 0, i.e. materials to its use, and finally a printed product with the developed extruder.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Biogas production from organic waste is a promising renewable energy source, but achieving optimal production and digester stability can be challenging. This study investigated the impact of the Evogen microbial additive on biogas production and digester quality through microbial abundance and physicochemical parameter analysis. Two biogas plants, BG01 and BG02, were examined using 16S rRNA profiling to assess microbial abundance. Simultaneously, physicochemical parameters, including FOS/TAC ratio, total solids, volatile solids, biogas production, and VFA profile, were measured to evaluate digester performance. Results revealed distinct microbial community shifts in Evogen-treated digesters. Increased abundance of methanogenic archaea and hydrolytic bacteria indicated improved anaerobic digestion. Evogen supplementation also positively affected digester performance, with higher FOS/TAC ratios indicating enhanced acidification and methanogenesis. Reductions in total solids and volatile solids demonstrated improved organic matter degradation. Significantly higher biogas production was observed in Evogen-treated digesters, highlighting its potential as a microbial additive. Furthermore, VFA profiling demonstrated improved process stability and reduced substrate inhibition in Evogen-treated digesters. In summary, Evogen microbial additive positively influenced microbial dynamics, improving biogas production and digester quality. These findings contribute to optimizing biogas production systems and understanding the complex microbial interactions within anaerobic digesters.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

A chairside polishing kit is an alternative to a laboratory polishing technique. This study aimed to evaluate the effects of different polishing techniques on the surface roughness of three-dimensional (3D)-printed acrylic denture bases (ADB). One hundred twenty disc-shaped specimens were fabricated from one conventional heat-polymerized (HP) ADB resin and two 3D-printed (Asiga (AS) and NextDent (ND)) ADB resins (n=40 per ADB resin). Each group was furtherly divided based on the polishing protocol (n=10) as follows: convectional polishing protocol (C), Microdont chairside polishing kit (M), Shofu chairside polishing kit (S), and unpolished group (U). The surface roughness (surface roughness average (Ra) and average maximum profile height (Rz)) of the printed specimens were measured using an optical profilometer, and the scanning electron microscope (SEM) was used to capture the surface at ×1000. Two-way ANOVA and post hoc tests were used for data analysis (α = 0.05) at significant levels. In unpolished groups, there was a statically significant difference between HP vs 3D-printed ADBs (p &lt; 0.0001). For Ra values, the lowest values were presented in HP-C, AS-S, and ND-C. While the highest values were shown in all unpolished groups. Within the material, there were statistically significant differences between the three polishing protocols (C, M, and S) vs unpolished (p &lt; 0.0001), while there was no significant between C, M, and S groups (p = 0.05). The Rz values had the same pattern as the Ra values. The two chairside polishing kits were comparable to conventional polishing technique, and it could be recommended for the clinical application.

The performance of a small reconfigurable unmanned aerial vehicle (UAV) is evaluated, 1 combining a multidisciplinary approach in computational analysis of additive manufactured struc- 2 tures, fluid dynamics, and experiments. Reconfigurable UAVs promise cost savings and efficiency 3 without sacrificing performance, while demonstrating versatility to fulfill different military mission 4 profiles. The use of computational fluid dynamics (CFD) in UAV design produces higher accuracy 5 aerodynamic data, which is particularly important for complex aircraft concepts such as blended 6 wing bodies. To address challenges relating to anisotropic materials, the Tsai-Wu failure criterion is 7 applied to structural analysis, using CFD solutions as load inputs. Aerodynamic performance results 8 show the low-speed variant attains an endurance of 1 hour, 48 minutes, whereas for its high-speed 9 counterpart, it is 29 minutes at 66.7% higher cruise speed. Each variant serves different aspects of 10 small UAS deployment in combat, with low-speed envisioned for close surveillance, and high-speed 11 for incursions. Experimental and simulation results suggest room for design iteration, in wing area 12 and geometry adjustments. Structural simulations demonstrated the need for airframe improvements 13 in the low-speed configuration. This paper highlights the potential of reconfigurable UAVs to disrupt 14 the industry, advocating for further research and design improvements.

The osseointegration process in and around additively manufactured (AM) lattice structures of a new titanium alloy, Ti–19Nb–14Zr, was evaluated. Three different implants, including lattices with increasing high sidewalls gradually closing them, were designed, manufactured and implanted in the tibia and metatarsal bone of two sheep for twelve weeks. After removal, they were characterized with X-ray computed tomography (XCT). The 3D XCT images were segmented using machine learning. The bone-interface implant (BII) and bone-implant contact (BIC) were studied. The results show that, since AM naturally leads to high roughness surface finish, the wettability of the implant is increased. The new alloy possesses an increased affinity to the bone enhancing the quality of osseointegration. The lattice provides crevices, in which the biological tissue can jump in and cling. The combination of these factors is pushing ossification beyond its natural limits. Therefore, the quality and speed of the ossification and osseointegration in and around these Ti–19Nb–14Zr AM laterally closed lattice implants open the possibility of bone spline key of prostheses. This enables the stabilization of the implant into the bone while keeping the possibility of punctual hooks allowing the implant to be removed more easily if required.