This manuscript discusses a novel method to map pressure results from one 3D surface shell mesh onto another. This technique is especially important when transferring results from one numerical analysis to another. This method works independent of the actual pressures, and only focuses on ensuring the surface areas consistently match. By utilizing this approach, the cumulative forces consistently match for all input pressures. This method is demonstrated to work for pressure profiles with precipitous changes in pressures, and with small quadrangular source elements being applied to a mix of large quadrangular and triangular target elements, and the forces at all pressure profiles match remarkably.

Traditional high pressure mechanical compressors account for over half of the car station’s cost, have insufficient reliability and are not feasible for a large-scale fuel cell market. An alternative technology, employing a two-stage, hybrid system based on electrochemical and metal hydride compression technologies, represents an excellent alternative to conventional compressors. The high-pressure stage, operating at 100-875 bar, is based on a metal hydride thermal system. A techno-economic analysis of the metal hydride system is presented and discussed. A model of the metal hydride system was developed, integrating a lumped parameter mass and energy balance model with an economic model. A novel metal hydride heat exchanger configuration is also presented, based on mini-channel heat transfer systems, allowing for effective high-pressure compression. Several metal hydrides were analyzed and screened, demonstrating that one selected material, namely (Ti_0.97Zr_0.03)_1.1Cr_1.6Mn_0.4, is likely the best candidate material to be employed for high-pressure compressors under the specific conditions. System efficiency and costs were assessed based on the properties of currently available materials at industrial levels. Results show that the system can reach pressures on the order of 875 bar with thermal power provided at approximately 150 °C. The system cost is comparable with the current mechanical compressors and can be reduced in several ways as discussed in the paper.

Intra-abdominal pressure (IAP) elevation during capnoperitoneum can cause adverse cardiovascular and respiratory effects. This study aimed to determine if a sequentially increased IAP affects cardiovascular and respiratory variables in anesthetized dogs and evaluate the effects of constant rate infusion of dexmedetomidine (Dex) on cardiovascular and respiratory variables with increased IAP. Five dogs were anesthetized, instrumented, and the Veress needle was equipped to adjust the IAP using a carbonic anhydrase insufflator. Stabilization was conducted for 1 h, and physiological variables were measured in IAPs of 0, 5, 10, 15, and 20 mmHg and after desufflation. After the washout period, the dogs underwent similar procedures along with constant rate infusion of dexmedetomidine. Cardiovascular effects of increased IAP up to 20 mmHg were not significant in healthy beagle dogs and those administered with dexmedetomidine. In the control group, the arterial pressure slightly increased, but not statistically significant, at an IAP of 20 mmHg compared with that at baseline (mean arterial blood pressure, p = 0.399; systolic arterial blood pressure, p = 0.293; diastolic arterial blood pressure, p = 0.141). When comparing the control and dexmedetomidine groups, overall significant effects of dexmedetomidine were noted on heart rate, cardiac output, and systemic vascular resistance during the experiment. Respiratory effects were not affected by abdominal insufflation when compared between different IAPs and between the two groups. Overall, an increased IAP of until 20 mmHg did not significantly affect cardiovascular and respiratory variables in both control and dexmedetomidine groups. This study suggests that dexmedetomidine infusion administration is applicable in laparoscopic procedures in healthy dogs.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

Almond is worldwide consumed and renowned as a valuable healthy food. In spite of this, it is also a potent source of allergenic proteins able to trigger several mild to life-threatening immunoreactions. Food processing proved to alter biochemical characteristics of proteins, thus affecting the respective allergenicity. In this paper we investigated the effect of autoclaving, preceded or not by a hydration step, on the biochemical and immunological properties of almond proteins. Any variation in the stability and immunoreactivity of almond proteins extracted from the treated materials, were evaluated by total protein quantification, ELISA assay and protein profiling by electrophoresis-based separation (SDS-PAGE). The autoclaving alone was found to weakly affect almond proteins stability, despite what observed for the combination of hydration and autoclaving, which resulted in a loss of approximately 70% of total protein content compared to untreated sample, and in a final negligible immunoreactivity, as well. The final SDS-PAGE protein pattern recorded for almonds hydrated and autoclaved disclosed significant changes. In addition, the same samples were further submitted to in vitro simulated gastro-duodenal (GI) digestion to evaluate potential changes induced by these processing on allergens digestibility. Digestion products were identified by HPLC-HRMS/MS analysis followed by software-based data mining, and complementary information were provided by analyzing the proteolytic fragments lower that 6 kDa in size. The autoclave based treatment was found not to alter the allergens digestibility, whereas an increased susceptibility to proteolytic action of digestive enzymes was observed in almonds subjected to the combination of prehydration and autoclaving. Finally, the residual immunoreactivity of the GI resistant peptides was investigated in-silico by bioinformatic tools, confirming that by following both approaches, no epitopes survived the almond digestion, thus demonstrating the potential effectiveness of these treatments to reduce almond allergenicity.

Background. Transferrin receptor 1 (TfR1), glucose transporter 1 (GLUT1), and CD98hc are candidates for targeted therapy at the blood-brain barrier (BBB). Our objective was to challenge the expression of TfR1, GLUT1, and CD98hc in brain capillaries by the histone deacetylase inhibitor (HDACi) valproic acid (VPA). Methods. Primary mouse brain capillary endothelial cells (BCECs) and brain capillaries isolated from mice injected intraperitoneally with VPA were examined using RT-qPCR and ELISA. Targeting to the BBB was performed by injecting monoclonal anti-TfR1 (Ri7217)-conjugated gold nanoparticles measured using ICP-MS. Results. In BCECs co-cultured with glial cells, Tfrc mRNA expression was significantly higher after 6 h VPA returning to baseline after 24 h. In vivo Glut1 mRNA expression was significantly higher in males, but not females', receiving VPA, whereas Cd98hc mRNA expression was unaffected by VPA. TfR1 increased significantly in vivo after VPA, whereas GLUT1 and CD98hc were unchanged. Uptake of anti-TfR1-conjugated nanoparticles was unaltered by VPA in spite upregulated TfR expression. Conclusions. VPA upregulates TfR1 in brain endothelium in vivo and in vitro. VPA does not increase GLUT1 and CD98hc proteins. The increase in TfR1 does not result in higher anti-TfR1 antibody targetability, suggesting targeting sufficiently occurs with available transferrin receptors without further contribution from accessory VPA-induced TfR1.

(1) Background: Lifestyle changes, eventually associated with a nutraceutical, are recommended strategies for managing high-normal blood pressure (BP) patients with low-moderate cardiovascu-lar (CV) risk. Nitrates-enriched products (i.e., red beet extracts) may help reduce BP, exerting vas-oactive properties and enhancing adherence to lifestyle advice. Our study aimed to evaluate the effectiveness in clinical practice of generic written lifestyle advice and a beetroot-based nutraceu-tical prescription based on the 2018 ESC/ESH guidelines on 24-hour BP in a population with high-normal BP and low-moderate CV risk.; (2) Methods: A longitudinal observational study was con-ducted in two ESH hypertension excellence centres on 43 consecutive subjects with high-normal BP based on repeated office BP (OBP) measurements and a low-moderate CV risk. Twenty-four-hour ambulatory BP monitoring (ABPM) was carried out at baseline and three months after ge-neric written ESC/ESH advice for lifestyle changes associated with a nutraceutical containing 500 mg of dry beetroot extract; (3) Results: Mean age 50±11 years, 54% males, 58% overweight/obese, mean OBP 135±3/85±3 mmHg. At baseline, 24-hour BP, daytime BP and night-time BP were 127±7/80±6 mmHg, 131±8/83±6 mmHg and 118±8/70±5 mmHg, respectively, BP profiles compat-ible with hypertension status in some subjects. After a median follow-up of 98 (92-121) days, all BPs, except night-time diastolic BP, were significantly decreased: -3±6/-2±4 mmHg for 24-hour BP, -3.9±6.0/-3.0±4.0 mmHg for daytime BP and -3.3±7.4/-1.3±4.7 mmHg for night-time BP, respec-tively. No significant clinical changes in weight were detected. BP decreased independently of baseline BP level, gender, smoking status and BMI, while a more substantial decrease in BP was observed in older patients; (4) Conclusions: Our pilot study shows for the first time that written generic lifestyle advice based on ESC/ESH hypertension guidelines coupled with a beetroot-based nutraceutical may represent a valid initial non-pharmacological approach in subjects with high-normal BP and low-moderate CV risk even without personalized diet interventions.

Introduction: intraocular pressure (IOP) measurement is an essential part glaucoma’s diagnosis and follow-up. Goldmann applanation tonometry (GAT) is the gold standard for IOP measurement but it’s affected by many factors like central corneal thickness (CCT). Racial differences in CCT are reported but the Syrian population was never studied.Research design and methods: 57 subjects with 114 eyes visiting Damascus hospital were examined and 100 eyes were included. IOP was measured using GAT and CCT was measured using OCULUS Pentacam AXL Corneal Topography, demographic data and history of ocular surgery, systemic co-morbidities and history of medications were collected. IOP values were corrected for CCT.Results: 56% were males, the mean age was 48.1. 24% of subjects had hypertension. Males had higher CCT with 557.23± 25.33 compared with 531.34 ± 41.88 for females. There was a moderately positive correlation between CCT and IOP (r=0.232, p-0.02), CCT and IOP values were linearly correlated (ANOVA, p=0.02).Conclusions: This study showed that the correlation between CCT and IOP is present in the Syrian population. Males had a slightly thicker corneas than females and CCT didn’t significantly change with age.

With the development of free trade port in Hainan Island, the construction of tourist roads around the island is also in full swing. Under the weather conditions of strong typhoon and rainstorm in Hainan, the highway cutting slope built on the coastal weak sandy terraces has strong sand loss and is easy to be scour by rainfall. MICP green spray irrigation solidification technology is used to strengthen the sandy cutting, and pore water pressure monitoring is carried out on the slope model during MICP solidification and rainfall scour. Combined with the model pore water pressure and flow slip failure pattern, dynamic analysis was carried out. The results show that MICP sprinkler irrigation technology can solidified the surface of the slope model in a short time, and the cementation depth of the model reaches 4cm after three sets of rotation reinforcement. The surface reinforcement effect is good, and the sand samples are closely connected. Under the erosion effect of simulated rainfall intensity, the sand loss of the slope is weakened, and no sand binding damage occurs, and the integrity is enhanced. Due to the cementation between sand grains, most of the rainfall was converted into runoff, and the slope slid after 150s. When the slope began to slip, the leading edge of the slope model lost sand and unloaded, and the failure mode was graded creep slip failure. Finally, the slope was divided into several blocks due to the continuous expansion of cracks after the slope failure. The erosion stability of the sandy slope under heavy rains is optimized and the sand loss is prevented effectively. In this study, a new method of MICP remediation techniques is proposed, which provides a new test basis for the application of MICP technology in practical engineering.

Precise association of serum leptin with body mass index (BMI) and blood pressure (BP; both systolic blood pressure (SBP) and diastolic blood pressure (DBP) is not well known for understanding their involvement in health and disease. Hence, the present study was planned to be conducted for investigating the association of BP, BMI and serum leptin levels in young normal weight (NW) and overweight (OW) male Saudi students. The NW (n: 198) and OW male subjects (n: 192) in the age range of 18-20 years were consulted. Blood pressure (BP) was measured with a mercury sphygmomanometer. Leptin Human ELISA Kits were employed for the determination of the serum leptin levels. The mean ± SD values of BMI (kg/m2), serum leptin (ng/ml), SBP (mmHg), and DBP (mmHg) all showed significant difference for young OW vs. NW male university students as: 27.52± 1.42 vs. 21.49± 2.03; 10.70± 4.67 vs. 4.68± 1.91; 121.37±2.59 vs.118.51±1.54 and 81.44±1.97 vs. 78.79±1.44 respectively. All associations (among BMI, leptin, SBP and DBP) showed positive linear and significant correlation except nonsignificant correlation of BMI and SBP for NW group. The present study in the young Saudi male students, presents significant variations for BP and serum leptin levels and significant positive linear association among serum leptin, BMI and BP.

Background: Idiopathic normal pressure hydrocephalus is a syndrome with neuroradiological findings and clinical pattern characteristic but not specific for the pathology. Since the prevalence is growing due to the rapidly aging society, standardized and validated protocol for diagnosis is needed, also because this condition may mimic other disorders among elderly such as Parkinson's and Alzheimer's disease. Material and methods: We analysed data from 44 patients with suspect diagnosis of idiopathic normal pressure hydrocephalus with age > 60 years, clinical triad and neuroradiological pattern examined in our ward from November 2018 to November 2022. Neu-ropsychological assessment includes Mini Mental State Examination and Mental Deterioration Battery. Motor scores were collected from gait and balance tests. The evaluation was performed before and after an extended lumbar drainage last 48h. Patients who has scores improvement after the extended lumbar drainage, undergo ventriculoperitoneal shunt with a programmable valve. Results: All patients undergo neuropsychological assessment and motor tests, only 2 patients were unable to perform motor tests because bedridden. 16 patients showed no benefit from the tests, in 2 cases even a worsening of cognitive performance. 28 patients showed an improvement in their performances, but in most cases the improvement involved only the neuropsychological as-sessment. All patients underwent ventriculoperitoneal shunt have had a typical answers pattern in Mental Deterioration Battery test. We performed 9 ventriculoperitoneal shunt and 1 ventricu-lo-atrial shunt. Conclusions: Qualitative neurocognitive tests come out to be more sensitive compared to quantitative neurocognitive tests in identifying patients with suspected idiopathic normal pressure hydrocephalus benefiting from extended lumbar drainage test and then un-derwent surgical treatment. This could be considered a valid screening in elderly patients with suspected idiopathic normal pressure hydrocephalus in order to minimize the number of invasive procedures. More studies are necessary to validate this tool.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

The purpose of the present study was to investigate the effects of psychological pressure on corticospinal excitability, the spinal reflex, lower limb muscular activity, and reaction times during a task involving dominant leg movements. Ten healthy participants performed a simple reaction time task by raising the heel of their dominant foot from a switch. After 20 practice trials, participants performed 20 non-pressure and 20 pressure trials in a counterbalanced order. Stress responses were successfully induced, as indexed by significant increases in state anxiety, mental effort, and heart rates under pressure. Significant increases in motor evoked potential (MEP) amplitude of the tibialis anterior muscle (TA) occurred under pressure. In terms of task-related EMG amplitude, the co-contraction rate between the soleus (SOL) and TA muscles significantly increased along with SOL and TA EMG amplitudes under pressure. Hoffmann reflexes for SOL and reaction times did not change under pressure. These results indicate that corticospinal excitability and leg muscle-related EMG activity increase homogeneously during lower limb movements that are performed under psychological pressure.

Runaway electrons (RAEs) generation in high-pressure gases is an important physical phenomenon that influences significantly discharge shapes and properties of initiated plasma. The diffuse discharges formed due to RAEs in air and other gases at atmospheric pressure find wide application. In the present review, theoretical and experimental results that explain the reason for the RAEs occurrence at high pressures are analyzed and recommendations are given on the implementation of conditions under which the runaway electron beam (RAEB) with the highest current can be obtained at atmospheric pressure. Experimental results were obtained using subnanosecond, nanosecond, and submicrosecond generators, including those specially developed for runaway electron generation. The RAEB were recorded by oscilloscopes and collectors with picosecond time resolution. To describe theoretically the phenomenon of continuous electron acceleration, the method of physical kinetics has been used based on the Boltzmann kinetic equation that takes into account the minimum but sufficient number of elementary processes, including shock gas ionization and elastic electron scattering. Results of modeling allowed the main factors to be established that control the RAE appearance, the most important of which is electron scattering on neutral atoms and/or molecules. Theoretical modeling has allowed the influence of various parameters (including the voltage, pressure, gas type, and geometrical characteristics of the discharge gap) to be taken into account. The results of research presented here allow the RAEs accelerators with desirable parameters to be developed and the possibility of obtaining diffuse discharges to be accessed under various conditions. The review consists of the Introduction, 5 Sections, the Conclusion, and the References.

This research aims to investigate the effects of parental pressure on students' academic achievement at the school level. The research objectives include examining the relationship between parental pressure and academic achievement and identifying potential moderating variables. A sample of middle and high school students will be utilized in this study.

New detailed geological/structural mapping as well as field-based structural analysis were carried out to investigate the deformation pattern of well-preserved high-pressure rocks of the Blueschist Unit exposed on SE Syros (Cyclades, Greece). Our new geological mapping revealed the occurrence of a metasedimentary sequence underlain by a meta-igneous sequence. The contact between these two sequences displays typically interfingering patterns in map-scale due to folding. The earlier ductile deformation phase recognized in the mapped area, is associated with the development of a penetrative foliation, which was formed under eclogite/blueschist facies conditions at peak conditions. The subsequent main deformation phase occurred at blueschist facies conditions synchronous with the early stages of exhumation of the high-pressure rocks. This phase is mainly associated with the formation of map-scale WNW-trending folds and a pervasive axial planar foliation linked with ESE-directed shearing. The main deformation ceased within blueschist facies conditions and exhumation of the rocks to greenschist facies conditions took place under very weak deformation. Greenschist retrogression observed in the southwestern part of the mapped area seems to be controlled by fluids rather than by intense deformation. Our results indicate that the high-pressure rocks of the Blueschist Unit exposed on Syros Island represent a large-scale pod of low deformation under blueschist to greenschist facies conditions, likely occupying the core of an extrusion wedge.

Pipe leakage is an inevitable phenomenon in water distribution networks (WDNs), leading to energy waste and economic damage. Leakage events can be reflected quickly by pressure values, and the deployment of pressure sensors is significant for minimizing the leakage ratio of WDNs. Concerning the restriction of realistic factors, including project budgets, available sensor installation locations, and sensor fault uncertainties, a practical methodology is proposed in this paper to optimize pressure sensor deployment for leak identification in terms of these realistic issues. Two indexes are identified to evaluate the leak identification ability, that is, detection coverage rate (DCR) and total detection sensitivity (TDS), and the principle is to determine priority to ensure an optimal DCR and retain the largest TDS with an identical DCR. Leakage events are generated by a model simulation and the essential sensors for maintaining the DCR are obtained by subtraction. In the event of a surplus budget, and if we suppose the partial sensors have failed, then we can determine the supplementary sensors that can best complement the lost leak identification ability. Moreover, a typical WDN Net3 is employed to show the specific progress, and the result shows that the methodology is largely appropriate for real projects.

In tunnel excavation with boring machines, the tunnel face is supported to avoid collapse and minimise settlement. This article proposes the use of reinforcement learning, specifically the Deep Q-Network algorithm, to predict the face support pressure. The approach is tested both analytically and numerically. By using the soil properties ahead of the tunnel face and the overburden depth as the input, the algorithm is capable of predicting the optimal tunnel face support pressure, adapting to changes in geological and geometrical conditions.

Abstract Background: Alcohol consumption is linked to urinary sodium excretion and both of these traits are linked to hypertension and cardiovascular diseases (CVDs). The interplay between alcohol consumption and sodium on hypertension, and cardiovascular diseases (CVDs) is not well-described. Here, we used genetically predicted alcohol consumption and explored relationships between alcohol consumption, urinary sodium, hypertension, and CVDs. Methods: We performed a comparative analysis among 295,189 participants from the prospective cohort of the UK Biobank (baseline data collected between 2006 and 2010). We created a genetic risk score (GRS) using 105 published genetic variants in Europeans that were associated with alcohol consumption. We explored relationships between GRS, alcohol consumption, urinary sodium, blood pressure traits, and incident CVD. We used linear, logistic regression and Cox proportional hazards (PH) models in our analysis. Results: Our analyses supported an interaction effect between alcohol GRS and urinary sodium on hypertension (P interaction =0.03) and CVD (P interaction =0.03). In presence of high urinary sodium excretion, alcohol GRS increases blood pressure in a more enhanced fashion. Conclusions: Our results show that decrease in urinary sodium excretion offsets the risk posed by genetic risk of alcohol consumption.

The zero velocity update(ZUPT) algorithm is the core of a foot-mounted pedestrian navigation system. The zero velocity detection method is the premise and guarantee of the effective application of the ZUPT algorithm. To make ZUPT work properly, it is necessary to detect zero velocity intervals correctly. The detection accuracy of the existing zero velocity detection methods is easy to be affected by users and environment. A novel zero velocity detection method based on the plantar pressure is proposed in this paper, which has higher detection accuracy and better environmental adaptability. First, the paper analyzes the motion characteristics of foot during walking. Second, the inherent relationship between the plantar pressure and the gait change during walking is studied based on the pressure sensor. Then, the model of the zero velocity detection method using the plantar pressure is established. Finally, the indoor and outdoor multi-scene experiments show that this method not only has a high detection accuracy, but also has good adaptability to users and walking environment.

Purpose: The evaluation of the efficacy of topical hypotensive treatment and/or systemic corticosteroids therapy in patients with elevated intraocular pressure and Graves’ orbitopathy (GO). Methods: 172 eyes in 86 individuals with duration of GO ≥ 3 months, intraocular pressure in either eye ≥ 25.0 mmHg and GO ranked ≥ 3 at least in one eye in modified CAS form, were included. The study subjects were divided into three treatment subgroups: subgroup I was administered latanoprost QD; subgroup II was administered a combined preparation of brimonidine and timolol BID; subgroup III was the control group, not receiving any topical hypotensive treatment. All the study participants received systemic treatment – intravenous corticosteroid therapy at the same dose, according to the EUGOGO guideline Results: On the final visit, the mean IOP value was significantly lower in all treatment subgroups comparing to the initial values. In both subgroups receiving topical treatment the IOP reduction was higher than in the control group receiving systemic corticosteroids only. However, the latanoprost eye drops decreased intraocular pressure more effectively than drops containing brimonidine and timolol. Conclusion: Topical ocular hypotensive treatment is effective in reducing intraocular pressure in GO and decreases intraocular pressure more effectively than systemic corticosteroid therapy alone.

Tree nuts confer many health benefits because of their high content of vitamins and antioxidants and they are increasingly consumed in the last the years. Food processing is an important industrial tool to modify allergenic properties of foods, in addition to ensure safety and to enhance organoleptic characteristics. The effect of high pressure, without and with heating, on SDS-PAGE and immunodetection profile of potential allergenic proteins (anti-11S, anti-2S and anti-LTP) of pistachio, cashew, peanut, hazelnut, almond and chestnut was investigated. Processing based on heat and /or pressure and Ultra high pressure (HHP, 300-600 MPa) without heating was applied. After treating the six tree nuts with pressure combined with heat a progressive diminution of proteins with potential allergenic properties was observed. Moreover, some tree nuts proteins (pistachio, cashew and peanut) seemed to be more resistant to technological processing than others (hazelnut and chestnut). Differences among tree nut varieties were found regarding to protein content, SDS and immunoblotting profile. High pressure combined with heating processing markedly reduce tree nut allergenic potential as the pressure and treatment time increases. HHP do not alter hazelnut and almond immunoreactivity

Pressure fluctuations beneath hydraulic jumps downstream of Ogee spillways potentially damage stilling basin beds. This paper deals with the extreme pressures underneath free hydraulic jumps along a smooth stilling basin. The experiments were conducted in a laboratory flume. From the probability distribution of measured instantaneous pressures, the pressures with different non-exceedance probabilities (P*a%) could be determined. It was verified that the maximum pressure fluctuations, as well as the negative pressures, are located at the positions closest to the spillway toe. The minimum pressure fluctuations are located at the downstream of hydraulic jumps. It was possible to assess the cumulative curves of P*a% related to the characteristic points along the basin, and different Froude numbers. To benchmark, the results, the dimensionless forms of mean pressures, standard deviations, and pressures with different non-exceedance probabilities were assessed. It was found that an existing methodology can be used to interpret the present data, and pressure distribution in similar conditions, by using a new third-order polynomial relationship for the standard deviation (σ*X) with the determination coefficient (R2) equal to 0.717. It was verified that the new optimized adjustment gives more accurate results for the estimation of the maximum extreme pressures than the minimum extreme pressures.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

Background: Current obstructive sleep apnea treatment relies on manual PAP titration, but it has limitations. Complex interactions during titration and variations in SpO2 data accuracy pose challenges. Patients with co-occurring chronic hypercapnia may require precise oxygen titration. To address these issues, we propose a Clinical Decision Support System using Markov Decision Processes. Methods: This study, compliant with data protection laws, focused on adults with OSA-induced hypoxemia utilizing supplemental oxygen and CPAP/BiPAP therapy. PAP titration, conducted over one night, involved vigilant monitoring of vital signs and physiological parameters. Adjustments to CPAP pressure, potential BiLevel transitions, and supplemental oxygen were precisely guided by patient metrics. Markov Decision Processes outlined three distinct phases for sleep disorder management, incorporating expert medical insights. Results: In our study involving 14 OSA patients (average age: 63 years, 27% females, BMI 41 kg m−2), significant improvements were observed in key health parameters. The initial AHI of 61.8 events per hour significantly decreased to an average of 18.0 events per hour after PAP and oxygen titration (p < 0.0001), indicating a substantial reduction in sleep-disordered breathing severity. Concurrently, SpO2 levels increased significantly from an average of 79.7% before titration to 89.1% after titration (p < 0.0003). Pearson correlation coefficients demonstrated aggravation of hypercapnia in 50% of patients (N=5) with initial hypercapnia during the increase of CPAP pressure. However, transitioning to BiPAP exhibited a reduction in pCO2 levels, showcasing its efficacy in addressing hypercapnia. Simultaneously, BiPAP therapy correlated with a substantial increase in SpO2, underscoring its positive impact on oxygenation in OSA patients. Markov dynamic process analysis demonstrated realistic patient behavior during stable night conditions, emphasizing minimal apnea and good toleration to high CPAP pressure. Conclusions: the development of a framework for Markov Decision Processes of PAP and oxygen titration algorithms holds promise for providing algorithms for deviation in pCO2 and SpO2 markers. While challenges remain, including the need for high-quality data, the potential benefits in terms of patient management and care optimization are substantial, and this approach represents an exciting frontier in the realm of telemedicine and respiratory healthcare. Obstructive sleep apnea, PAP titration, hypoxia, hypercapnia, Markov decision processes

Background: In recent years, the assessment and guidance of cardiopulmonary resuscitation (CPR) quality using noninvasive and invasive monitoring techniques have been increasingly recommended. In this study, we introduce a new physiological monitoring system that simultaneously measures arterial pressure (AP), venous pressure (VP), and cerebral tissue oxygen saturation (SctO2) during CPR. Methods: This prospective observational study was conducted at a single center (Kagoshima City Hospital). Adult out-of-hospital patients aged ≥18 years with an intravenous femoral arterial line, venous line, and SctO2 monitor were included. We measured femoral arterial pressure (FAP) and femoral venous pressure (FVP) invasively if catheters were immediately inserted into the femoral artery and vein for potential candidates who require interventions such as extracorporeal cardiopulmonary resuscitation but did not receive such interventions as a result. Results: We observed several representative cases that provided the following insights: We presented several cases, including two patients with significant increases in FVP and low SctO2 values, and in both cases, return of spontaneous circulation (ROSC) was not achieved. In contrast, we also presented two cases in which CPR resulted in higher FAP compared to FVP and an upward trend in SctO2 values was observed, and both instances achieved ROSC. Conclusion: We presented a simultaneous physiological monitoring system that can monitor AP, VP, and SctO2 during CPR. Further case accumulations will be necessary to assess the variations in hemodynamic status during CPR and the association between each hemodynamic status and outcomes after cardiac arrest.

The spiral tube heat exchange is widely used in large-scale liquefaction process. However, the research on the friction pressure drop of the two-phase flow in the spiral tube is limited, especially for the offshore sloshing condition. In this paper, an experimental system is designed and built, and the effects of sloshing form (roll, pitch, heave), sloshing period (5-15s), mass flux (200-800 kg/(m2·s)), vapor quality (0.3-0.9) and operating pressure (2-4 MPa) on friction pressure drop of methane/ethane (C1/C2) mixture in spiral tube are studied. The result shows that the growth rate of time-averaged friction pressure drop during condensation under sloshing condition is less than 0, which indicates that sloshing will lead to drag reduction. And under the three sloshing parameters, the growth rate of time-averaged friction pressure drop of C1/C2 is reduced by-5.99%%, 5.97% and -6.70% respectively.

Silicon-based microchannel technology offers unmatched performances for cooling high energy physics silicon-pixels detectors. Although Si-Si direct bonding, used for the fabrication of cooling plates, meets the stringent requirements of this application, in particular high-pressure resistance (~200 bar), it is reported to be a challenging and expensive process. In this work, we have evaluated two alternative bonding methods towards a more cost-effective fabrication process: Si-Glass-Si anodic bonding (AB) with a thin-film glass and Au-Au thermocompression (TC). The bonding strength of the two methods were evaluated with destructive pressure burst tests (0 - 690 bar) on test structures, each made of a 1×2 cm² silicon die etched with a tank and an inlet channel and sealed with a plain silicon die using AB or TC bonding. The pressure resistance of the structures was measured to be higher for the TC sealed samples (max. 690 bar) than for the AB ones (max. 530 bar) but less reproducible. The failure analysis indicates that the AB structure resistance is limited by the adhesion force of the deposited layers. Nevertheless, both the TC and AB methods provided sufficient bond quality to hold the high pressure required for the high energy physics pixel detectors cooling application.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

In the extra-thick coal seams and multi-layered hard roofs, the longwall hydraulic support yielding, coal face spalling, strong deformations of goaf-side entry, and severe ground pressure dynamic events typically occur at the longwall top coal caving longwall faces. Based on the Key strata theory an overburden caving model is proposed here to predict the multilayered hard strata behaviour. The proposed model together with the measured stress changes in coal seam and underground observations in Tongxin coal mine provides a new idea to analyse stress changes in coal and help to minimise rock bursts in the multi-layered hard rock ground. Using the proposed primary Key and the sub-Key strata units the model predicts the formation and instability of the overlying strata that leads to abrupt dynamic changes to the surrounding rock stress. The data obtained from the vertical stress monitoring in the 38 m wide coal pillar located adjacent to the longwall face indicates that the Key strata layers have a significant influence on ground behaviour. Sudden dynamically driven unloading of strata was caused by the first caving of the sub-Key strata while reloading of the vertical stress occurred when the goaf overhang of the sub-Key strata failed. Based on this findings several measures were recommended to minimise the undesirable dynamic occurrences including pre-split of the hard Key strata by blasting and using the energy consumption yielding reinforcement to support the damage prone gate road areas. Use of the numerical modelling simulations was suggested to improve the key theory accuracy.

Objective To observe the effect of roxadustat on blood pressure and micro-inflammatory response in patients with hemodialysis anemia, and to provide a viable technique for the treatment of hemodialysis anemia patients. Methods A total of 100 hemodialysis anemia patients admitted to the Nephrology Department of our hospital from July 2020 to July 2021 were enrolled and randomly divided into an observation group (roxadustat) and a control group (human recombinant erythropoietin (rhEPO). The clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure were recorded and compared. Results There was no significant difference in baseline data and serum indicators (P>0.05). The study group demonstrated superior performance to the control group in terms of clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure (all P<0.05). Conclusion Compared with rhEPO treatment, roxadustat exhibits a promising outcome in treating anemia and has slight impact on blood pressure of patients.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

In this study, we had investigated the use of high-pressure homogenization (HPH) as a novel pretreatment method for the extraction of sodium alginate (SA) from Laminaria japonica. Our results demonstrated that under optimal condition of 100 MPa HPH pressure, 4 cycles, pH 6.0, and 0.5% ethylene diaminetetra acetic acid tetrasodium salt (EDTA) concentration (w/v) for 3.0 hours, the extraction yield of HPH reached 34%, which was higher than that achieved by previous methods such as complex enzyme hydrolysis (CE), ultrasonic-assisted extraction (UAE), and complex enzyme-ultrasonic combined method (CE-UC). To further characterize the extracted SA, we conducted a comprehensive analysis using SEM, FTIR, MRS, NMR, XRD, TGA, and T-AOC assay. Our findings revealed the following: 1) HPH treatment significantly disrupted the structure of L. japonica cells and reduced their crystallinity to 76.27%, the lowest among all pretreatment samples; 2) the extracted SA had a greater tendency to form elastic gels; and 3) the antioxidant activity of HPH-extracted SA reached 0.02942 mgVceq∙mg-1, which was the highest among all tested methods. Based on these results, we concluded that HPH extraction not only increased the yield of SA but also enhanced its antioxidant activity.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

Background: Due to the importance of brain death (BD) diagnostic do not mistake, reliable confirmatory exams should be performed to enhance its security. This study aims to evaluate the intracranial pressure (ICP) pulse morphology behavior in brain-dead patients through a noninvasive monitoring system. Methods: A pilot case-control study was conducted in adults that met the BD national protocol criteria. Quantitative data from the ICP waveforms were extracted and analyzed comparing BD patients and health subjects. Results: Fifteen patients were included. ICP waveforms presented substantial differences amidst BD patients when compared to the control group. Moreover, pulse amplitude and time to peak variables values in the case group were also statistically significant. Conclusions: In this exploratory study, noninvasive ICP waveforms have shown potential as a screening method in patients with suspected brain death. Future studies should be carried out in a larger population.

From the perspective of manufacturing companies, the political, media and economic discourse on decarbonisation of the recent years manifests itself as an increasing social expectation of action. In Germany in particular, this discourse is also being driven forward by powerful companies, respectively sectors, most notably the automotive industry. Against this background, it was examined how German manufacturing companies react to rising societal pressure and emerging policies. It is examined which measures the companies have taken or plan to take to reduce their footprint, which aspirations are associated with this and by which structural characteristics (company size, energy intensity, sector) these are influenced. A mix methods approach was applied, utilising data gathered from approx. 900 companies in context of the Energy Efficiency Index of German Industry (EEI), along with media research focusing on decarbonisation plans and initiatives announced. We demonstrate that one-size-serves-all approaches are not suitable to decarbonise industry as the situation and ambitions differ considerably depending on size, energy intensity and sector. Even though the level of ambition and urgency is high, particularly micro and energy intensive companies are challenged. The research uncovers a series of questions that call for attention to materialise the ambitions and address the challenges outlined.

We validated a new noninvasive tool (B4C) to assess intracranial pressure waveform (ICPW) morphology in a set of neurocritical patients, correlating the data with ICPW obtained from invasive catheter monitoring. Materials and Methods: Patients undergoing invasive intracranial pressure (ICP) monitoring were consecutively evaluated using the B4C sensor. Ultrasound-guided manual internal jugular vein (IJV) compression was performed to elevate ICP from the baseline. ICP values, amplitudes, and time intervals (P2/P1 ratio and time-to-peak [TTP]) between the ICP and B4C waveform peaks were analyzed. Results: Among 41 patients, the main causes for ICP monitoring included traumatic brain injury, subarachnoid hemorrhage, and stroke. Bland-Altman’s plot indicated agreement between the ICPW parameters obtained using both techniques. The strongest Pearson’s correlation for P2/P1 and TTP was observed among patients with no cranial damage (r = 0.72 and 0.85, respectively) in detriment of those who have undergone craniotomies or craniectomies. P2/P1 values of 1 were equivalent between the two techniques (area under the receiver operator curve [AUROC], 0.9) whereas B4C cut-off 1.2 was predictive of intracranial hypertension (AUROC 0.9, p < 000.1 for ICP > 20 mmHg). Conclusion: B4C provided biometric amplitude ratios correlated with ICPW variation morphology and is useful for noninvasive critical care monitoring.

Obtaining a good socket fit is an iterative process dependent on the skill and experience of the prosthetist creating it, and requiring individualisation based on the size and shape. There is no standard measurement system used to aid prosthetic socket creation, despite the severe impacts on physical health and quality of life if one is ill-fitting. Pressure sensors embedded in a prosthetic socket were used to collect data at the socket-residuum interface. To choose an interpolation method, a 2D grid was used, with previously collected walking test pressure data, to simplify the sensor array with a border for extrapolation. Four multivariable interpolation methods were evaluated to create a colour map of the pressure data. Radial Basis Function interpolation was chosen as it produced a clear image with a graduated interpolation between data points and was used to create a colour map across the surface of a 3D prosthetic socket model. For the model to be accessible to clinical audiences, a desktop application was created using PyQt to view the model. The created application allowed for connection to the sensors via Bluetooth, with the pressure data updating the colour map on the 3D model in real-time. The created application shows the potential for a clinical product, however further development informed by feedback from rehabilitation clinicians and prosthesis users is required

Synthetic chalcomenite-type cupric selenite CuSeO₃∙2H₂O has been studied at room temperature under compression up to pressures of 8 GPa by means of single-crystal X-ray diffraction, Raman spectroscopy, and density-functional theory. According to X-ray diffraction, the orthorhombic phase undergoes an isostructural phase transition at 4.0(5) GPa with the thermodynamic character being first-order. This conclusion is supported by Raman spectroscopy studies which have detected the phase transition at 4.5(2) GPa and by the first-principles computing simulations. The structure solution at different pressures has provided information on the change with pressure of unit-cell parameters as well as on the bond and polyhedral compressibility. A Birch-Murnaghan equation of state has been fitted to the unit-cell volume data. We found that chalcomenite is highly compressible with a bulk modulus of 42 – 49 GPa. The possible mechanism driving changes in the crystal structure is discussed, being the behavior of CuSeO₃∙2H₂O mainly dominated by the large compressibility of the coordination polyhedron of Cu. On top of that, an assignation of Raman modes is proposed based upon density-functional theory and the pressure dependence of Raman modes discussed. Finally, the pressure dependence of phonon frequencies is also reported.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

Oscillometric blood pressure (BP) devices currently estimate a single point but do not identify fluctuations in BP or distinguish them from variations in response to physiological properties. In this paper, to analyze BP normality based on oscillometric measurements, we use statistical approaches including kurtosis, skewness, Kolmogorov-Smirnov, and correlation tests. Then, to mitigate uncertainties, we use a deep neural network (DNN) to determine the confidence limits (CLs) of BP measurements based on their normality. The proposed DNN regression model decreases the standard deviation of error (SDE) of the mean error (ME) and the mean absolute error (MAE) and reduces the uncertainty of the CLs and SDEs of the proposed technique. We validate the normality of the distribution of the BP estimation distribution which fits the Gaussian distribution very well. We use a rank test in the DNN regression model to demonstrate the independence of the artificial SBP and DBP estimations. First, we perform statistical tests to verify the normality of the BP measurements for individual subjects. The proposed methodology provides accurate BP estimations and reduces the uncertainties associated with the CLs and SDEs based on the DNN regression estimator.

The effects of psychological pressure on perceiving the height of a jump bar just before starting a high jump run was investigated. University students (N = 14) training for a high jump event performed 15 trials (3 practice, 6 pressure, and 6 non-pressure) in counterbalanced order in their daily practice environment. The height of the bar was judged as significantly higher on pressure trials compared to non-pressure trials. A regression analysis indicated that participants who reported increased subjective perceived pressure tended to judge the bar to be higher. There was no significant difference between pressure and non-pressure trials for the performance index, defined as the success rate. This study provides the first evidence that environmental perceptions prior to executing a motor task under pressure may make performance of the task appear to be more difficult.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

Due to the periodic movement of the piston in the reciprocating pump, the fluid will cause pressure pulsation, and the vibration of the pipeline will lead to instrument distortion, pipe failure and equipment damage. Therefore, it is necessary to study the vibration phenomena of the reciprocating pump pipeline based on the pressure pulsation theory. This paper starts from the reciprocating pump pipe pressure pulsation caused by fluid, pressure pulsation in the pipeline and the excited force is calculated under the action of the reciprocating pump. Then, the numerical simulation model is established based on the pipe beam model, and the rationality of the numerical simulation method is verified by the indoor experiment. Finally, a case study is taken as an example to analyze the vibration law of the pipeline system, and proposed the stress reduction and vibration reduction measures. The main conclusions are drawn from the analysis: (1) Excited force is produced in the bend or tee joint, and it can also influence the straight pipe in different levels; (2) In this pipeline system, the pump discharge pipe has a larger vibration amplitude and lower natural frequency; (3) The vibration amplitude increases with the pipe thermal stress, and when the oil temperature is higher than 85°C, it had a greater influence on the vertical vibration amplitude of the pipe.

We have investigated the antiferromagnetic phase transition in the frustrated and multiferroic hexagonal manganites $h$-(Y$_{0.98}$ Eu$_{0.02}$)MnO$_3$ (YEMO) and $h$-YMnO$_3$ (YMO). Elastic neutron scattering has been used to study in detail the phase transition in YMO and YEMO in zero pressure and in YMO at a hydrostatic pressure of 1.5~GPa. In zero pressure, we find the critical temperature $T_{\rm N} = 72.11(5)$~K and 71.3(1)~K and the critical exponent $\beta = 0.206(3)$ and 0.22(2), for YEMO and YMO, respectively. This is in agreement with earlier work by Roessli {\em et al.}. In applied hydrostatic pressure of 1.5~GPa, the ordering temperature increases to $T_{\rm N} = 75.2(5)$~K, in agreement with earlier reports, while $\beta$ is unchanged. Inelastic neutron scattering was used to determine the anisotropy spin wave gap at the phase transition, expected from spin wave theory to close with a critical exponent $\beta'$ identical to the one of the order parameter, $\beta' = \beta$. Our results indicate that the gap in YEMO indeed closes at $T_{\rm N}=72.4(3)$~K with $\beta' = 0.24(2)$, while the in-pressure gap in YMO closes at 75.2(5)~K with an exponent of $\beta' =0.19(3)$. In addition, the low-temperature anisotropy gap was found to have a slightly higher absolute value under pressure. The consistent values obtained for $\beta$ in the two systems support the likelihood of a new universality class for triangular, frustrated antiferromagnets.

Incretin effect helps in regulating glucose homeostasis and maintaining glycaemic control within the human body. This effect is achieved by the two naturally occurring incretin hormones: glucose-dependent insulinotropic polypeptide (GIP) and glucagon-like peptide-1 (GLP-1). Such hormones released by specialized entero-endocrine cells of the gastrointestinal tract cause insulin augmentation after food consumption. However, incretin effects are impaired in type 2 diabetic, primarily attributed to the deterioration of GLP-1 function along with decreased GLP-1 receptor expression. Targeting this hormone has, therefore, become an important therapeutic approach to treat this diabetic condition. Native GLP-1’s brief half-life and rapid proteolytic degradation have generated significant enthusiasm in uncovering the long-acting GLP-1 receptor (GLP-1R) agonists to manage type 2 diabetes. These synthetic peptides mimic the natural GLP-1 to activate GLP-1R and effectively exert various physiological benefits in terms of weight management, blood pressure, lipid profile, obesity and major adverse cardiovascular event. This review paper provides insights into the structure, function and expression of GLP-1 and its receptor. It also summarizes existing literature regarding different types of GLP-1 receptor agonists, their effects on blood pressure and how they exert their actions. While animal models have contributed significantly to this area of study, the scarcity of human studies is noted, indicating a need for more investigation in this domain. Expanding research in humans will help in comprehending the impact of GLP-1 receptor agonists on blood pressure regulation and their underlying mechanisms.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

Polymethyl methacrylate (PMMA) polymer is widely used in various fields today. In order to thoroughly reveal the structural impact performance of PMMA materials, this paper is based on the comprehensive Johnson-Cook constitutive model and damage failure model, and accurately confirm the J-C constitutive and damage failure model parameters of PMMA through material test data, The dynamic process of steel bullet impacting PMMA plate structure is analyzed by finite element software ABAQUS. The calculation results show that the numerical simulation results in this paper are in good agreement with the experimental test data. Therefore, the feasibility and accuracy of the impact analysis of PMMA structures based on J-C constitutive and damage failure models in this paper are studied. Finally, based on the J-C constitutive model and damage failure model, the variation of the residual velocity of the bullet with the PMMA plate thickness is analyzed in depth, that is, the results show that the residual velocity of the bullet has a certain linear relationship with the plate thickness.

In this paper, we investigated the capacitive effect and the electromagnetic coupling on the measurement chain induced by the gas gun or the powder gun during impact experiments. Reduced bandwidth and noise have been noticed on experimental signals. Rogowski coil measurements have been added on the cables to characterize the electromagnetic coupling. The perturbation currents on the cables have been quantified depending on the configuration. The gauge, the transmission line and the conditioning system have been modeled. The calculations have reproduced the electrical wave arrival time, the transmission line transfer impedance, the conditioning system transfer impedance and it shows the bandwidth limitation. A capacitive effect with the piezoresistive manganin gauge embedded into the sample has been identified depending on the experimental setup.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

Zinc oxide (ZnO) as a semiconductor in its crystalline or amorphous form is still a promised material, especially under isobaric and isothermal ensembles. In this work, Parallel and Equilibrium Molecular Dynamics and DL_POLY_4 software are employed to predict the relationship between the behavior of ZnO chemical bonds and the phase transition literatures, using correlation function g(r) of Zn-Zn, Zn-O, and O-O pairs. Our system is composed of 5832 atoms of ZnO rocksalt structure (2916 atoms of Zn2+ and 2916 atoms of O2-), under the temperature of 300 (K) and the range of pressure 0-400 (GPa). The lengths of ZnO bonds, the standard error, standard deviation, the maximum of g(r), and the percentage of the variation of the bonds are analyzed. The interatomic interactions are modeled by the potential of Buckingham for short-range and Coulomb for long-range interactions. The calculations were run on the RAVEN Supercomputer of Cardiff University (UK). Our data are mostly in the vicinity of available information of bonds lengths; the rest can be deduced from the pressure of phase transition to use it as a new approach of phase transition confirmation. However, the rest of our results are still a prediction because of no results under extended pressure used in this work.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Pressure Ulcers (PU) are a debilitating and often painful condition. They are localized lesions on the skin and/or underlying tissues and are common in the elderly, immobile people, diabetics and vascular disease or malnutrition, as well as in those requiring intensive or palliative care. Prevention and treatment of PU involve strategies to optimize hydration, circulation and nutrition. Nutrition plays a key role in pressure ulcer care because wounds require macronutrients and micronutrients to heal. Reports relating to the effectiveness of "Complementary Enzyme Therapy" also in the vulnological field led us to this study, the aim of which was to test the activity of a biodynamic nutritional supplement (Citozym®), characterized by a marked antioxidant activity, administered topically and/or systemically, in patients suffering from PU. The treatment showed a marked reduction in bedsores and in many cases their complete healing. Furthermore, it was possible to observe a lower incidence of side effects compared to conventional therapies. The results obtained, confirmed by various tests, and recognized by the scientific community, allow us to conclude that treatment with Citozym® could represent a new and effective strategy for the treatment of PU.

Burn patients still represent an important challenge in critical care medicine today. These patients can develop significant neurological conditions up to intracranial hypertension, but as they find themselves hospitalized outside of neurocritical care and are often subjected to sedation for the complex management, they are sometimes underestimated. The aim of this study is to evaluate the feasibility of non-invasive methods for the early diagnosis of intracranial hypertension in these patients. In this prospective observational study, adult burn patients admitted to intensive care within the first 8 hours of the event were enrolled. These patients were studied through ultrasound measurement of optic nerve sheath diameter and intracranial vessel velocimetry with transcranial Doppler. In the 20 patients studied, no frankly pathological values were identified in the 3 different measurement stages (within 8 hours of the burn, then at 48 and 96 hours) and no correlations were identified between the measured values and the extension of the burn with the related risk of mortality. However, this study, one of a kind, demonstrates that these non-invasive methods are applicable to this specific patient population, and can represent an effective method for reducing the incidence of complications that are dangerous for survival.

The European Fish Index EFI+ is the only fish-based multimetric index for the assessment of the ecological status of running waters validated and thus applicable across the European Union. Metrics of the index rely on several attributes of the species present in the fish assemblage, irrespective of their native/alien status. The abundance of alien fish, together with other anthropogenic impacts, is one of the most important threats to the conservation of native fish and ecosystem health and is also an indicator of degraded stream conditions. Therefore, to improve the performance and utility of the EFI+ in regions with high incidence of alien species, the EFI+ was adapted to include the alien fish pressure by averaging the two original metrics with a new metric that reflects the number of alien species as well as the proportional abundance of alien individuals. The application of the adapted index (A-EFI+) is illustrated with data from several Iberian Mediterranean basins and showed similar or stronger correlations than the original EFI+ with anthropogenic pressure (land-use variables) and with other regional fish indices. EFI+ has been invaluable to intercalibrate fish indices across Europe and A-EFI+ is similar but explicitly includes the alien pressure, thus helping to provide a more comprehensive assessment of ecosystem health and to communicate it to society.

The service life of the reinforced concrete structure in the marine environment can be impaired significantly due to chloride-induced corrosion. However, how the chloride diffusion in pre-cracked concrete structures is affected by the hydrostatic pressure magnitude is poorly understood. This study experimentally examined the effect of hydrostatic pressure on the chloride diffusion in pre-cracked concrete. Cracks with five different widths, i.e., 20 μm, 40 μm, 60 μm, 80 μm, and 100 μm, were manually created using a splitting tensile apparatus respectively. The chloride diffusion in the concrete with a certain crack was then studied under four different hydrostatic pressures of 0 MPa, 0.1 MPa, 0.3 MPa, and 0.5 MPa. Experimental results show that the chloride diffusion in concrete with a crack greatly relies on both the hydrostatic pressure and the crack width. The chloride concentration increases as the hydrostatic pressure grows, particularly for the wider cracks with width ranging from 60 μm to 100 μm. Surprisingly, the hydrostatic pressure has a negligible effect on the chloride distribution in the concrete with a crack width no larger than 40 μm. Both the chloride diffusion coefficient and the surface chloride concentration of concrete increased gradually as the hydrostatic pressure increased. The experimental findings enrich our understanding of the behavior of pre-cracked concrete when exposed to chloride-induced corrosion at different depths of marine environments.

Using numerical software to establish a three-dimensional geological model of shield tunneling through fault fracture zones, considering the synchronous grouting effect at the shield tail, the disturbance of various geotechnical structures in the fault fracture zone under deep burial and high water pressure conditions is studied. According to the comparison between the numerical model analysis results and the on-site inspection results of the entire process of Shiziyang B3 section, synchronous grouting at the shield tail is the main reason for the changes in soil and water pressure in the fault fracture zone area. The soil and water pressure changes strongly during shield tunneling, and the maximum excess pore pressure value occurs when the shield tail passes. When the shield tunneling machine is far away, the soil and water stress shows a downward trend. The impact of synchronous grouting decreases with the increase of tunneling distance. Due to the difference in permeability, the variation law of pore pressure in the fault fracture zone is significantly different from the original rock, leading to a faster increase in pore pressure in the fracture zone area and a wider range of influence.

Hypertension is one of the most common and significant cardiovascular risk factor. With the emergence of COVID-19, concerns have arisen about its potential to exacerbate cardiovascular morbidity and mortality. Several theories have emerged linking hypertension with COVID-19. However, the relationship between SARS-CoV-2 infection and long-term risk of hypertension remains insufficiently explored. Therefore, our study aimed to investigate the impact of COVID-19 infection on blood pressure and long-term risk of hypertension developing. A comprehensive search was conducted in the PubMed and SCOPUS databases up to 10th August 2023 for relevant papers. The analysis included 35 eligible articles. The majority of the latest studies pointed to increase BP after COVID-19 infection. However, several observations contradicted the influence of SARS-CoV-2 on the hypertension development or suggesting a transient effect. The possible role of the loss of angiotensin-converting enzyme 2, cytokine storm, increased sympathetic activity, and endothelial dysfunction were considered. On the other hand, BP changes following COVID-19 could be a consequence of lifestyle changes, which often accompanied COVID-19 infection. Our findings highlight the urgent need for comprehensive research on the COVID-19 and hypertension link. These insights are crucial for implementing effective prevention and management strategies for individuals with the history of COVID-19 infection.

In the struggle for survival, all organisms have evolved adaptations for protection from predation. Angiosperms are among the most abundant producers on the planet, but they are trapped in a precarious symbiosis with animals for pollination and fruit dispersal, while also having to deter herbivory. About 10% of all angiosperms produce the deterrent latex from ubiquitous isoprene precursors. Latex is an aqueous suspension of rubber particles and other compounds which works as an antifeedant by clogging chewing mouthparts and by coagulating into a solid in stomach acid. A survey of stomach pHs from various animals supports the hypothesis that foregut-fermenting ruminants have evolved the capacity to evade latex coagulation due to the presence of anterior digestive chambers with near-neutral to alkaline pH before it enters the acidic abomasum. Hindgut-fermenting animals lack this adaptation and have to eat forage which is low in latex, such as grasses. The latex-adaptive foregut browsers vs. latex-maladapted hindgut grazer hypothesis has implications for both livestock and zoo animals which may be provided with forage that is not optimal for their gut health. Further, ruminants and herbivorous tadpoles are at risk for damage by popular bioinsecticides such as Bt which are activated by alkaline gut pH.

The intracranial pressure (ICP) signal, as monitored on patients in intensive care units, contains pulses of cardiac origin where P1 and P2 subpeaks can often be observed. When calculable, the ratio of their relative amplitudes is an indicator of the patient’s cerebral compliance. This characterization is particularly informative on the overall state of the cerebrospinal system. We developed a recurrent neural network-based framework for P2/P1 ratio computation that only takes a raw ICP signal as an input. Two tasks are performed, namely pulse classification and subpeak designation. Pulse classification was achieved with an area under the curve of 0.90 on a 4,344-pulse testing dataset, while the peak designation algorithm identified pulses with a P2/P1 ratio > 1 with a 97.3% accuracy. Although it still needs to be evaluated on a larger number of labeled recordings, our automated P2/P1 ratio calculation framework appears to be a promising tool for improving bedside monitoring devices.

The purpose of this scoping review was to examine the literature on the use of anti-gravity treadmill and its effects on lower limb motor functions in children and adolescents with locomotor impairments. Four databases (MEDLINE, CINAHL, Embase, Web of Science) were searched for articles from inception to August 2021. Inclusion criteria were: (1) experimental or quasi-experimental studies using the anti-gravity training as the primary intervention; (2) studies conducted in paediatricpediatric participants; (3) articles reporting outcomes related to the lower limb functions; and (4) studies published in French or English. Fifteen articles were included in the review. Studies included children and adolescents aged 4–18 years with locomotor impairments. The intervention duration was ranged from 2 and to 12 weeks, with 2-5 sessions per week. Included studies showed reported that anti-gravity training induces improvements in muscle strength, balance, spatiotemporal gait parameters, and walking endurance in children with locomotor impairments. This review provides relevant information about the modalities, outcomes and limits associated with the anti-gravity training protocol reported in the literature. Overall, the anti-gravity treadmill training could be viewed as a valuable training modality for children with cerebral palsy. However, more precise, and comprehensive description of anti-gravity rehabilitation protocols would be useful.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

We propose the physical proof-of-concept of a new simple miniature pressure sensor based on the whispering gallery modes (WGMs) optically excited in a dielectric microsphere placed near a flexible reflective membrane, which acts as an ambient pressure sensing element. WGMs excitation is carried out by free-space coupling of optical radiation to a microsphere. The distinctive feature of proposed sensor design is double excitation of optical eigenmodes by forward and backward propagating radiation reflected from a membrane that causes WGMs interference in particle volume. The optical intensity of resulting resonant field established in the microsphere carries information about the exact position of the pressure-loaded reflecting membrane. The sensitivity of the proposed sensor strongly depends on the quality factor of the excited resonant mode, as well as geometrical and mechanical parameters of the flexible membrane. We propose to register not the displacement of the position of the WGM resonance, but the change in its amplitude under the influence of the change in the distance between the sphere and the mirror under the influence of pressure. Important advantages of the proposed sensor are miniature design (linear sensor dimensions depends only on the membrane diameter) and the absence of a mechanical contact of pressure-sensitive element with WGM resonator.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

For our research on droplet deformation and breakup in scaled high-pressure homogenizing units we developed a pressure stable inline droplet generator. It consists of an optically accessible flow channel with a combination of stainless steel and glass capillaries and a 3D printed orifice. The droplet size is determined online by live image analysis. The influence of the orifice diameter, the mass flow of the continuous phase and the mass flow of the disperse phase on the droplet diameter was investigated. Furthermore, the droplet detachment mechanisms were identified. Droplet diameters with small diameter fluctuation between 175 µm and 500 µm could be realized, which allows a precise adjustment of the Ca and We Number in the subsequent scaled high pressure homogenizer disruption unit. The determined influence of geometry and process parameters on the resulting droplet size and droplet detachment mechanism agreed well with literature on microfluidics. Furthermore, droplet trajectories in an exemplary scaled high-pressure homogenizer disruption unit are presented which show that the droplets can be reinjected on a trajectory close to the center axis or close to the wall, which should result in different stresses on the droplets.

Pistachio and cashew contain allergenic proteins, which causes them to be removed from the diet of allergic people. Former evidences have demonstrated that food processing (thermal and non-thermal) can produce structural and/or conformational changes in proteins by altering their allergenic capacity. In this study, the influence of Instant Controlled Pressure Drop (DIC) on the pistachio and cashew allergenic capacity has been studied. Western blot was carried out using IgG anti-11S and anti-2S and IgE antibodies from sera of patients sensitized to pistachio and cashew. DIC processing causes changes in the electrophoretic pattern, reducing the number and intensity of protein bands, as the pressure and temperature treatment increment what results in a remarkable decrease of detection of potentially allergenic proteins. The harshest conditions of DIC (7bar, 120s) markedly reduce the immunodetection of allergenic proteins, not only by using IgG (anti 11S and anti 2S) but also when IgE sera from sensitized patients were used for Western blots. Such immunodetection is more affected in pistachio than in cashew nuts, but it not completely removed. Therefore, cashew proteins are possibly more resistant than pistachio proteins. According these findings, Instant Controlled Pressure Drop (DIC) can be considered a suitable technique in order to obtain hypoallergenic tree nuts flour to be used in food industry.

Long-term durability of the vacuum edge-seal plays a significant part in retrofitting triple vacuum glazing (TVG) to existing buildings in achieving towards zero-energy buildings (ZEB) target. Vacuum pressure decrement with respect to time between panes affect the thermal efficiency of TVG. This study reports a 3D finite element model, with validated mathematical methods and comparison, for the assessment of the influence of vacuum pressure diminution on the thermal transmittance (U value) of TVG. The centre-of-pane and total U values of TVG calculated to be 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ at the cavity vacuum pressure of 0.001 Pa. The results suggests that a rise in cavity pressure from 0.001 Pa to 100 kPa increases the centre-of-pane and total U values from 0.28 Wm⁻²K⁻¹ and 0.94 Wm⁻²K⁻¹ to 2.4 Wm⁻²K⁻¹ and 2.58 Wm⁻²K⁻¹, respectively. The temperature descent on the surfaces of TVG between hot and cold sides’ increases by decreasing the cavity vacuum pressure from 50 kPa to 0.001 Pa. To maintain the cavity vacuum pressure of 0.001 Pa for over 20 years of life span in the cavity of 10 mm wide edge sealed triple vacuum glazing, non-evaporable getters will maintain the cavity vacuum pressure that will enable the long-term durability to TVG.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

Purpose: To investigate whether microsurgical excision of trabecular meshwork (TM) in an ex vivo pigmentary glaucoma model can normalize the hypertensive phenotype. Methods: Eight eyes of a porcine pigmentary glaucoma model underwent 90° of microsurgical TM excision with an aspirating dual-blade (Goniotome (G)). 24 hours later, an additional 90° of TM were removed. Anterior segments with sham surgeries served as the control (C). Outflow facility and intraocular pressure (IOP) were analyzed. Histology with hematoxylin and eosin (H&E) was obtained. Results: After the first 90° TM excision, IOP was significantly lower in G (10.23±2.39 mmHg, n=7) than C (20.04±1.97mmHg, n=8, P<0.01). Outflow facility in G (0.38±0.07 µl/min/mmHg) was higher than C (0.16±0.02 µl/min/mmHg, P<0.01). After the second 90° TM excision, IOP in G (6.46±0.81 mmHg, n=7) was significantly lower than C (20.25±1.66 mmHg, n=8, P<0.001), while the outflow facility in G (0.50±0.05 µl/min/mmHg, n=7) was higher than C (0.16±0.01 µl/min/mmHg, n=8, P<0.001). Compared to the first excision, excision of an additional 90° did not change of IOP (P=0.20) or outflow facility (P=0.17) further. Conclusion: Excision of 90° of TM in a pigmentary glaucoma model using an aspirating dual-blade decreased IOP and increased outflow facility. Translational Relevance: Microsurgical TM excision over 90° can effectively restore outflow in pigmentary glaucoma.

Understanding the infiltration and solidification processes of liquid 5083Al alloy into Al2O3 three-dimensional reticulated porous ceramic (Al2O3(3D) RPC) is essential for optimizing the microstructure and properties of Al2O3(3D)/5083Al interpenetrating phase composites (IPCs) prepared by low-pressure infiltration process (LPIP). This study employs ProCAST software to simulate the infiltration and solidification processes of liquid 5083Al with pouring velocities (PV) of 0.4 m/s infiltrating into Al2O3(3D) RPC preforms with varying porosities at different pouring temperatures (PT) to prepare Al2O3(3D)/5083Al IPCs using LPIP. The results demonstrate that pore diameter of Al2O3(3D) RPC preforms and PT of liquid 5083Al significantly influence the of the infiltration. Solidification process analysis reveals that the Al2O3(3D) RPC preform with smaller pore diameters allows the lower pouring velocity of 5083Al to solidify faster compared to the preform with larger pore diameters. Al2O3(3D)/5083Al IPCs were prepared successfully from Al2O3(3D) RPC porosity of 15 PPI with liquid 5083Al at PV 0.4 m/s and PT 800 °C using LPIP, resulting in nearly fully dense composites, where both Al2O3(3D) RPCs and 5083Al interpenetrate throughout the microstructure. The infiltration and solidification defects were reduced under air pressure of 0.3 MPa (corresponding to PV of 0.4 m/s) during LPIP. Finite volume method simulations are in good agreement with experimental data, validating the suitability of the simplified model for Al2O3(3D) RPCs in the infiltration simulation.

Hypertension and arterial stiffness are the main factors contributing to cardiovascular disease. L-citrulline, a nitric oxide precursor, has been proposed as a blood pressure-lowering intervention. This study aimed to investigate the impact of L-citrulline on central and peripheral blood pressure, arterial stiffness, and muscle oxygenation at rest and during an isometric knee extension exercise protocol. Twelve older males received 6 g of L-citrulline or a placebo for six days using a double-blind crossover design. Blood hemodynamics parameters (i.e., arterial and brachial systolic and diastolic blood pressure, mean arterial pressure, pulse pressure, heart rate), arterial stiffness (i.e., augmented pressure, augmentation index, forward, backward wave pressure and carotid-femoral pulse wave velocity) and muscle oxygenation [i.e., oxyhemoglobin (Δ[O2Hb]) and deoxyhemoglobin (Δ[HHb]), total hemoglobin concentration (Δ[tHb]) and tissue saturation index (TSI%)], were measured at baseline, post-supplementation and during isometric exercise. No significant effects of L-citrulline supplementation were observed at rest or during exercise on blood pressure, arterial stiffness, and muscle blood flow. Both central and peripheral blood pressure were increased during the exercise, which is consistent with isometric contractions. The results of the present study question the efficacy of short-term L-citrulline in decreasing blood pressure at rest or attenuating blood pressure increases during isometric exercise.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

This study explores the application of numerical analysis and material models to predict ice impact loads on ships and offshore structures operating in polar regions. An explicit finite element analysis (FEA) approach was employed to simulate an ice and steel plate collision experiment conducted in a cold chamber. The pressure and strain history during the ice collision were calculated and compared with the experimental results. Various material model configurations were applied to the FEA to account for the versatile behavior of ice—whether ductile or brittle—its elastic-plastic yield criteria, and its dynamic strain rate dependency. In addition to the standard linear elastic perfectly plastic and linear elastic-plastic relationships, this study incorporated the crushable foam and Drucker-Prager models, based on the specific ice yield criteria. Considering the ice’s strain rate dependency, collision simulations were conducted for each yield criteria model to compute the strain and reaction force of the plate specimens. By comparing the predicted pressures for each material model combination with the pressures from ice collision experiments, our study proposes material models that consider the yielding, damage, and behavioral characteristics of ice. Lastly, our study proposes a combination of ice material properties that can accurately predict collision force.

Exposure to traffic-related air pollution is linked with acute alterations in blood pressure (BP). We examined the cumulative short-term effect of black carbon (BC) exposure on systolic (SBP) and diastolic (DBP) BP and assessed effect modification by participant characteristics. SBP and DBP were repeatedly measured on 152 traffic enforcers. Using a linear mixed-effects model with random intercepts, quadratic (QCDL) and cubic (CCDL) constrained distributed lag models were fitted to estimate the cumulative effect of BC concentration on SBP and DBP during the 10-hours (daily exposure) and 7-days (weekly exposure) before the BP measurement. Ambient BC was related to increased BP with QCDL models. An interquartile range change in BC cumulative during the 7-days before the BP measurement was associated with increased BP [1.2% change in mean SBP, 95% confidence interval (CI), 0.1 to 2.3; and 0.5% change in mean DBP, 95% CI, –0.8 to 1.7]. Moreover, the association between the 10-hours cumulative BC exposure and SBP was stronger for females (4.0% change, 95% CI: 2.1–5.9) versus males, and for obese (2.9% change, 95% CI: 1.0–4.8) vs. non-obese traffic enforcers. Short-term cumulative exposure to ambient traffic-related BC could bring about cardiovascular diseases through mechanisms involving increased BP.

Polymer-derived ceramic (PDC) based coatings like Si-C-N and their derivatives are gaining importance day by day in N/MEMS and aerospace due to their thermos-mechanical stability and conductivity. The crystallized, amorphous, and near amorphous morphology of SiCN nanocomposite coatings based on deposition conditions requires thorough investigation for appropriate utilization as they lead to differences in mechanical properties (quantified using nanoindentation in this case). A 4-stage model was proposed based on Raman spectroscopy due to the N₂-Ar pressure variations during the deposition process of SiCN coatings by magnetron sputtering. The integral intensity of the G (graphitic), disorder (D), and tetrahedral (T) peaks namely I_G, I_D, and I_T were calculated after the deconvolution of the spectra. The sp² domain size and defect parameters were evaluated and correlated with the hardness and different bond formation involving Si, C, and N. Image analysis revealed the atomic migration involved during the growth process leading to crystallization along with the formation of voids and defects. The observations were supported by FTIR and TEM-SAED analysis. The outcomes provide a foundation causing an urge to develop similar models with further elemental additions and correlate with various physical properties.

This article presents a detailed examination of the methodology and modeling tools utilized to analyze gas flow in pipelines, rooted in the fundamental principles of gas dynamics. The methodology integrates numerical simulations with modern neural network techniques, particularly focusing on the Physics-Informed Neural Network (PINN) method. This innovative approach combines artificial neural networks (ANNs) with physical equations, offering a more efficient and accurate way to model various complex processes and phenomena. The proposed mathematical model, based on the Euler equation, has been meticulously implemented using the Python language. Verification with analytical solutions ensures the accuracy and reliability of the computations. In the research, a comprehensive comparative analysis was conducted between results obtained using the PINN method and those from conventional Computational Fluid Dynamics (CFD) approaches. The analysis highlighted the advantages of the PINN method, which produced smoother pressure and velocity fluctuation profiles while reducing computation time, demonstrating its potential as a transformative modeling tool. The data derived from this study are of paramount importance for ensuring ongoing energy supply reliability and can also be used to create predictive models related to gas behavior in pipelines. The application of modeling techniques for gas flow simulation has the potential to revolutionize the integrity of our energy infrastructure and utilization of gas resources. However, it is crucial to emphasize that the effectiveness of such models relies on continuous monitoring and frequent updates to ensure alignment with real-world conditions. This research not only contributes to a deeper understanding of compressible gas flows but also underscores the crucial role of advanced modeling methodologies in the sustainable management of gas resources for both current and future generations.

The paper is devoted to the study of a high-pressure short-arc xenon discharge, which is widely used as a light source. Cathodes of such lamps are often doped with thorium for better cathode operation. As a result, thorium can evaporate into a discharge. The study is based on a model of a short-arc xenon discharge plasma, which includes presence of thorium atoms in the plasma. The data obtained show that thorium atoms strongly affect the characteristics of the plasma, reducing its temperature, changing the ionic composition near the cathode, energy balance and generation of optical radiation. Especially interesting is the case when the discharge electrodes have a different shape of the working surface: the anode has a convex or concave shape; the cathode has a different cone angle. The obtained data make it possible to propose a new way to increase the luminous efficiency of xenon lamps due to the appropriate choice of the electrodes working surface shape, which turned out to be an unexpectedly strong factor of affecting plasma characteristics. This, in turn, allows us to develop xenon lamps with the desired characteristics providing optical radiation in the required range of the spectrum and better use of energy.

Anesthetics reduce cardiac functions and lower blood pressure (BP), potentially causing excessive BP reduction in dehydrated patients or those with heart conditions, such as coronary artery disease (CAD). Considering the increased prevalence of cardiovascular disease with age, anesthesiologists must be cautious about BP reduction during general anesthesia in older adults. In the present case, an undiagnosed CAD patient in a hypovolemic state experienced a significant systolic blood pressure drop to the 50s during propofol and sevoflurane anesthesia. Despite the use of vasopressors, excessive hypotension persisted, leading to anesthesia suspension. Subsequent cardiac examinations, including computed tomography heart angio and calcium score, and coronary angiogram, revealed a near total occlusion of the left main coronary artery and the formation of collateral circulation. After 5 days of hydration and anticoagulation medications and confirmation of normovolemic state, general anesthesia was attempted again and successfully induced; a normal BP was maintained throughout the surgery. Thus, it is important to conduct a thorough cardiac evaluation and maintain normovolemia for general anesthesia in older adults.

Autonomic dysregulation is associated with cardiovascular consequences in obstructive sleep apnea (OSA). This study aimed to investigate the effect of acute continuous positive airway pressure (CPAP) treatment on autonomic activity and to identify factors contributing to the heart rate variability (HRV) changes in OSA. Frequency domain HRV parameters were calculated and compared between the baseline polysomnography and during the CPAP titration in 402 patients with moderate to severe OSA. There were significant reductions in total power, very low-frequency band power, low-frequency band power, and high-frequency band power during the CPAP titration as compared to the baseline polysomnography. This tendency was more pronounced in men than in women, and in patients with severe OSA than those with moderate OSA. Multivariate analysis found that changes in apnea-hypopnea index and oxygen saturation were significantly associated with changes in sympathetic and parasympathetic activity, respectively. This study demonstrated that HRV parameters significantly changed during the CPAP titration, indicating a beneficial effect of CPAP in restoration of sympathetic and parasympathetic hyperactivity in OSA. Prospective longitudinal studies should determine whether long-term CPAP treatment aids in maintaining the long-lasting improvement of the autonomic functions, thereby contributing to the prevention of cardiovascular and cerebrovascular diseases in patients with OSA.

Building situated in the flow path of wind is subjected to differential velocity and pressure distribution around the building envelope. Wind effects are influenced and vary for each individual shape of the tall building. Tall building structures are considered as cantilever structures with fixed ends at the ground. Wind exponential velocity acting along the height of the building makes velocity and pressure distribution more complex as the height of the building structure increases. This study discussed the effect of wind on an irregular cross-section shape. The study was conducted numerically with a building model placed in a virtual wind tunnel using the ANSYS (CFX) software tool. Wind effects are investigated on building model situated in a terrain category - II defined in IS: 875 (Part 3): 2015 wind scale model of 1:100 and turbulence intensity is 5 % and power law index α is considered as 0.143. Validation and verification of the study were made by comparing pressure coefficients on faces of a rectangular model of similar floor area and height as taken for a C-plan diamond-shaped model under similar boundary conditions, wind environment, and solver setting of numerical setup. The values of surface pressures generated on the recessed faces of the model and wind flow patterns within the recessed cavity were studied at wind incident angles 0°, 300, 60°, 1050, 1350 & 1800. The critical suction on all the recessed faces was observed to be at a 105° angle of wind attack.

A numerical method using combined detached-eddy simulation (DES) and cavitation model considering the rotation effect is used for unsteady cavitation flow field of the centrifugal pump. Closed type pump test system was established to obtain the pump performance and pressure pulsation characteristics under different flow rates and cavitation condition, which provide boundary conditions and verification of calculations. Based on the calculation results of the unsteady flow field of the centrifugal pump cavitation, the entropy generation analysis of the flow field and the pressure fluctuation characteristics were carried out. Then the relationship between cavitation and the deterioration of the centrifugal pump performance and the generation of the unstable operation excitation force was tried to reveal. The internal energy loss is mainly concentrated in the impeller, volute, and pump cavity area, which accounts for more than 85% of the total entropy generation. The characteristic frequency of about 0.333 Strouhal Number appears at the volute tongue due to the cavitation flow spread downstream.

Polymer-based composites reinforced with nanocarbonaceous materials can be tailored for functional applications. Poly(vinylidene fluoride) (PVDF) reinforced with carbon nanotubes (CNT) or graphene with different filler contents have been developed as potential piezoresistive materials. The mechanical properties of the nanocomposites depend of the PVDF matrix, filler type and filler content. PVDF 6010 is a relatively more ductile material, whereas PVDF-HFP shows larger maximum strain near 300% strain for composites with CNT, 10 times higher than the pristine polymer. This behaviour is similar for all composites reinforced with CNT. On the other hand, rGO/PVDF composites decrease the maximum strain compared to neat PVDF. It is shown that the use of different PVDF copolymers does not influence the electrical properties of the composites. On the other hand, CNT as filler leads to composites with percolation threshold around 0.5 wt.%, whereas reduced graphene oxide (rGO) nanocomposites shows percolation threshold at ≈2 wt.%. Both nanocomposites present excellent linearity between applied pressure and resistance variation, with pressure sensibility (PS) decreasing with applied pressure, from PS≈ 1.1 to 0.2 MPa^-1. A proof of concept demonstration is presented, showing the suitability of the materials for industrial pressure sensing applications.

Expressions for the axial pressure profiles in a cylindrical channel and between parallel plates or a rectangular channel with large aspect ratio, with Maxwell slip gas flow are derived from first principles. The resulting expressions, which only involve the inlet and outlet pressures and the channel dimensions, will be useful in modelling or simulations of channel flows at Knudsen numbers in the range 0.001–0.1, such as in MEMS and NEMS. The expression for a cylindrical channel is validated by deriving from it an expression for the channel mass flow, which is shown to agree with a known expression for the mass flow through cylindrical channels with Maxwell slip flow. The expression for flow between parallel plates is found to agree with the zeroth order relation derived by Arkilic et al. using perturbation analysis. The effect of the accommodation coefficient on the pressure profile in a cylindrical channel is shown.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

The financial equilibrium of the enterprise is an important company function ensuring by itself the maintenance of the enterprise of the competitive market. The financial equilibrium is analysed in numerous empirical studies. In this empirical study we highlight for the first time in a research the impact that taxation has on the financial equilibrium of some companies over ten years, period that includes the pre-crisis, the financial crisis and post-crisis periods.

This study investigated clinical nurses’ knowledge and visual differentiation ability of the pressure injury classification system (PICS) and incontinence-associated dermatitis (IAD), additionally analyzing possible influencing factors. A convenience sample of 248 nurses took the PICS and IAD knowledge test (KT) and completed the visual differentiation ability test (VDAT), consisting of 21 photographs with clinical information. The overall mean score for correct answers was 12.65±2.90 points in PICS & IAD KT and 11.43±4.57 points in VDAT. Incorrect responses were most common for statements related to stage Ⅱ, Ⅲ, IAD for PICS & IAD KT, and deep tissue pressure injury (DTPI), unstageable, and stage Ⅲ for VDAT. Significant correlations were found between PICS & IAD KT and VDAT (r=.252, p<.001). Factors affecting scores for VDAT were the scores of PICS & IAD KT, debridement experience in nursing patients with PI, and the management frequency of PI and IAD. Results indicate that nurses have an overall understanding of PICS and IAD, but low visual differentiation ability regarding stage Ⅲ, DTPI, and unstageable PI. Continuing education is needed to further improve knowledge and visual differentiation ability for PICS and IAD.

Background: Sex differences in blood pressure (BP) exist during all reproductive life between women and men whereas a sharper increase in BP occurs after menopause which is associated with increased prevalence of cardiovascular diseases. This study examined cardiovascular and biochemical parameters in perimenopausal women (PW) aiming to investigate the influence of sex on a) office BP and for 24 hours; b) cardiac autonomic modulation; c) redox state by measuring MDA, SOD, and catalase; d) NO_x^- concentration. In addition, aerobic exercise training (AET) was applied for detecting changes in cardiovascular responsiveness during the menopausal transition. Methods: Thirty-one participants were enrolled, healthy PW and age-matched men. Cardiovascular and biochemical biomarkers were evaluated at baseline and after AET (8 weeks of exercise on a treadmill, three sessions/week, duration of 30-40 minutes). Results: At rest, PW presented: a) a lower diastolic BP during daytime; b) a lower absolute and normalized LF component as well as a higher HF normalized component; d) no sex differences for redox biomarkers and NO_x^- concentration. After AET, only PW was responsive in lowering systolic BP that was accompanied by an increase in NO_x^- concentration and SOD activity. Regarding HRV, both groups were responsive to the AET. Conclusions: During the menopausal transition, systolic BP was similar to men whereas cardiac autonomic modulation remained unaltered showing the influence of sex steroids on BP. In Addition, AET was fundamental during the menopause transition by preventing an elevation in BP, minimizing the effects of aging associated with estrogen deficiency on women's cardiovascular health.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

In the field of engineering, tracked vehicles play a significant role in accessing challenging terrains. Maintaining trafficability is of the utmost importance when it comes to tracked vehicles traversing rugged terrains; it provides stability, traction, and adaptability for a wide range of applications, including deep-sea exploration. The terrain characteristics pertain to the interactions that determine the mobility of tracked vehicles. Traditional Terramechanics models are in-adequate in depicting the correlation between tracks and soil. An important issue is the lack of consideration for the moisture content in the soil and the rate at which sinking occurs in these models. Examining sinkage speed helps describe the ability of tracked vehicles to move at high speeds. The focus is on the critical factors influencing the mobility of tracked vehicles, precisely the sinkage speed and its relationship with pressure. Experimental tests in a soil bin, utilizing Bentonite/Diatom sediment soil, aim to measure these terrain factors. The study introduces a rubber-tracked vehicle, pressure, and moisture sensors to monitor pressure sinkage and moisture, evaluating cohesive soils (Bentonite/Diatom) in combination with sand and gravel mixtures. Findings reveal that higher moisture content in Bentonite soil leads to increased track slippage and sinkage compared to Diatom soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics in contrast to bentonite soil. The distinct behaviors of these soils underscore the complexity of terrains, emphasizing the need for a meticulous understanding of soil properties before applying them in natural environments. Furthermore, this study contributes precision in assessing natural terrains, enhancing tracked vehicle design, and advancing terrain mechanics comprehension for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

The results of electron-beam processing of Mn-Zn ferrite samples using pulsed and continuous electron beams in the forevacuum pressure range (10 Pa) are presented. We find that continuous electron-beam processing leads to surface structuring of the ferrite, changes in elemental composition on the surface, and electrical property modification. The degree of ferrite parameter changes exhibits a threshold behavior. For surface processing temperatures below 900 °C, changes are barely noticeable, while for temperatures over 1100 °C the surface resistance decreases by more than an order of magnitude. Electron-beam processing with millisecond pulse duration and pulse energy density exceeding 15 J/cm² results in the formation of low zinc content melt islands, while the remaining surface area (outside the islands) elemental content and ferrite properties remain largely unchanged. The thickness of the modified layer depends on the processing mode and can be controlled over the range 0.1–0.5 mm. Because of its low resistance, the modified layer can be utilized to enhance the RF-absorbing properties of the ferrite.

The influence of cuff inflations on nighttime measurements during 24h ambulatory blood pressure (BP) measurements is unknown. We investigated the potential effect of cuff-inflations on asleep parameters using measurements taken simultaneously with a cuffless device using pulse-transit-time (PTT). On the first day of measurement, standard cuff-based 24h BP and cuf-fless measurements were simultaneously performed on right and left arms (CUFF/PTT-D). 1-2 days after the first measurement, the cuffless device was worn alone (PTT-D). Only data from the cuffless device was analyzed. The following mean asleep parameters were analyzed: systolic and diastolic BP, arousals, sleep efficiency, total arousals, arousal per hour and desaturations. 21 in-dividuals were prospectively enrolled. Mean (SD) age was 47(±15) years and 57% were female. Mean systolic asleep BP for the during CUFF/PTT-D and during PTT-D were 131(±21) and 131(±26) mmHg respectively. Mean diastolic asleep BP values during CUFF/PTT-D and during PTT-D were 80(±14) and 84(±14) mmHg respectively (p=0.860, p=0.100 respectively). Systolic and diastolic asleep mean difference was 0.1 (±18.0) and -3.6 (±9.8) mmHg, respectively. There were significantly more total arousals during PTT-D (p=0.042). There was no significant difference seen in sleep efficiency (p=0.339) or desaturations (p=0.896) between the two measurements. We could not show any significant impact from cuff inflations during asleep PTT-D measurements.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

In New Orleans, Louisiana the population’s poor baseline health led to its establishment as an early epicenter for severe acute COVID-19. Antici-pating future outbreaks of COVID-19 and other respiratory viruses, we need to identify correlates of outcome, from real clinical experience. 89 patients were recruited into the ClinSeqSer acute COVID-19 longitudinal observational study, from the beginning of the outbreak in March to July 2020. Patients admitted for acute COVID-19 were enrolled in person. The cohort is unique as it is 68% Black, 53% female, of average age of early 60s, and prevalence of obesity and hypertension respectively of 55% and 83%. The outcomes are: 53% severe (20% fatal, 33% non-fatal) and 47% non-severe, with severe defined as death or requiring mechanical ventila-tion or high flow oxygen. Obesity and admit systolic blood pressure (SBP) >140mmHg are each associated with severe outcome and, despite respective sensitivity of 71% and 76%, specificity ~66% for both, and ac-curacy of 60% and 70% by ROC analysis, would likely provide useful predictors of outcome in critically stressed health care systems. We discuss pathophysiologic hypotheses to explain why high admit SBP is observed only in half of patients with pre-COVID hypertension and is associated with severe outcome.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Abstract Several studies have been conducted to strengthen weak road layers, regardless of whether they are un-der construction or are undergoing maintenance. Using substrates filled with different materials has proven effective for increasing the strength of these layers. In this study, I evaluated the coefficient of lateral soil pressure under various conditions when using reinforced and unreinforced piles filled with in-expensive material and the extent of their contribution to strengthening road layers. The results con-firmed that there was a difference in the coefficient of lateral soil pressure when the sand-filled piles were reinforced. The sand-filled piles were divided into several parts by arming. The maximum coeffi-cient of lateral soil pressure was 0.38 in the case of sand (1 mm) with reinforcement, whereas it was 0.29 in the same case without reinforcement as shown in Figure 1. The maximum coefficient of lateral soil pressure was 0.27 in the case of granite grain (2 mm) with reinforcement, whereas it was 0.17 in the same case without reinforcement. Moreover, the maximum lateral pressure coefficient was 0.26 in the case of granite grain (3 mm) with reinforcement, and it was 0.30 in the same case without reinforce-ment.

Chilean jack mackerel (Trachurus murphyi) is recognized as one of the most valuable pelagic resources across the southeast Pacific Ocean. Despite its nutritious properties it is an underused resource due to its rapid spoilage. The use of high hydrostatic pressure (HHP) for the processing of aquatic products could be an efficient alternative to cold storage since HHP might inactivate microbial pathogens and slow down spoilage microorganisms, therefore extending the product’s shelf life. The aim of the study was to compare the effect of HHP at 450 and 550 MPa for 3 min on the physicochemical properties of jack mackerel muscle undergoing pre- and post-rigor mortis stage and further storage for 26 days at 4°C. pH, total volatile basic nitrogen, trimethylamine, color, water-holding capacity, and texture were assessed. The proximate composition, pH, total volatile basic nitrogen, trimethylamine, color, water holding capacity, and texture, showed significant changes between untreated and treated samples, while the water holding capacity was virtually unaffected. Overall results showed an acceptable and long-lasting edible quality of Trachurus murphyi stored at 4°C when preserved through HHP. These findings suggest that the HHP might be able to industrially scale the production of highly physicochemical superior and minimally processed fish products.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.