Keywords: friction stir processing; additive manufacturing; wire; titanium alloy; material transfer; microstructure; microhardness

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

Ransomware attacks have rapidly proliferated, inflicting severe financial damages on businesses and individuals. Machine learning approaches to automate ransomware detection have shown promise but grapple with challenges like limited training data. This study introduces a novel deep learning model for few-shot ransomware classification. The model employs entropy features derived directly from malware binaries coupled with a twin neural network architecture utilizing transfer learning. Tests on over 1000 samples across 11 families demonstrate a weighted F1-score of 85.8\%, surpassing existing methods. The approach mitigates biases in limited training data and preserves intricacies lost in image-based features. It exhibits precise classification capabilities even with sparse samples of new ransomware variants. The research highlights the potential of entropy-driven deep learning to equip defenses against emerging zero-day ransomware strains.

This article presents a proposed system that enables energy transfer from the dc grid to a single-phase onboard grid, operating at an hi frequency. In addition to the energy transfer function, it additionally enables compensation of reactive power in the ac grid when the converter operates at less than rated power. To operate in compensator mode, it is necessary to decouple the current from the grid into active and reactive components and control them independently. To achieve good dynamics, synchronizers that operate in the dq system are used. In the case of a single-phase grid, it requires such a synchronizer to generate virtual quadrature signals. The used systems based on second-order generalized integrator are good, but to improve dynamics in the work a quadrature generator based on trigonometric calculations was proposed. The developed system was implemented in a proportional resonant current control system. Tests performed in steady state and in dynamic states related to typical grid disturbances showed better dynamic properties than the standard integrator-based system.Keywords: power transfer; compensator; P+R controller

We report a detailed investigation of vibrational modes, structure, and dynamics of glutathione (GSH) solutions using ultrasonic relaxation spectroscopy, FT-IR vibrational spectroscopy and electronic absorption measurements. The experimental data were analyzed in view of density functional theory (DFT) and molecular docking calculations. Three distinct Debye-type relaxation processes are resolved in the acoustic spectra, which are assigned to conformational changes between GSH conformers, self-association of GSH, and protonation processes. The standard volume changes for each process were estimated both experimentally and theoretically revealing a close resemblance among them. The higher the effect of the relaxation process in the structure, the greater the induced volume changes. From the temperature dependence of specific acoustic parameters, the thermodynamic characteristics of each process were determined. The experimental FT-IR spectra were compared with the corresponding theoretically predicted vibrational spectra revealing that the GSH dimers and extended conformers dominate the structure of GSH solutions in the high concentration region. The absorption spectra in the ultraviolet region confirmed the gradual aggregation mechanism that takes place in the aqueous GSH solutions. The results of the present study were discussed and analyzed in the framework of the current phenomenological status of the field.

The synthesis and characterization of the multicomponent crystals formed by 2,2’-thiodiacetic acid (H2tda) and 2,6-diaminopurine (Hdap) or N9-(2-hydroxyethyl)adenine (9heade) are reported. The crystals are in the salt rather than cocrystal form, as witnessed by single crystal X-ray diffractometry where a structural analysis revealed their ionic nature, confirming the proton transfer from the 2,2’-thiodiacetic acid to the basic groups of the coformers. The new multicomponent crystals have molecular formulas [(H9heade+)(Htda)] (1) and [(H2dap+)2(tda2)]·2H2O (2), and were also characterized by FTIR, elemental analysis as well as thermogravimetric/differential scanning calorimetry (TG/DSC) analyses. In the crystal packing the ions interact with each other via O–H···N, O–H···O. N–H···O and N–H···N hydrogen bonds generating cyclic hydrogen bonded motifs with graph-set notation of R22(16), R22(10), R32(10), R33(10), R22(9), R32(8) and R42(8), to form different supramolecular homo- and hetero-synthons. In addition, in the crystal packing of 2, pairs of diaminopurinium ions display an strong anti-parallel ,-stacking interaction, with short inter-centroids and interplanar distances (3.39 and 3.24 Å respectively) and fairly tight angle (17.5°). These assemblies have been further analyzed energetically by using DFT calculations, MEP surface analysis and QTAIM characterization.

We offered the circuit of a discrete analog filter (DAF) low frequencies of second-order on switchable capacitors, which differs from the known ones in that three capacitors with one terminal are connected to a common bus, and the frequency of the DAF pole depends not only on the ratio of the capacitances of the frequency-setting capacitors, but also on the ratio of resistances two additional resistors in the feedback. This allows at constant values ​​of the capacitances and a fixed switching frequency of electronic switches, control the pole frequency by changing the resistance ratio of additional resistors. Computer simulation of the developed circuit was performed in the Micro-Cap environment. It has been established that the DAF has a transmission coefficient close to minus one at very low frequencies and a transmission coefficient close to zero at higher frequencies.

In this paper, we redefine the boundaries of blood cell classification, expanding from 5 to 11 distinct blood cell types using the challenging 11-class PBC dataset. This shift enables a deeper understanding of blood cell diversity, overcoming previous limitations in medical image analysis. Our approach combines state-of-the-art deep learning techniques, including pre-trained ConvNets, ViTb16 models, and custom CNN architectures. We employ transfer learning, fine-tuning, and ensemble strategies, such as CBAM and Averaging ensembles, to achieve unprecedented accuracy and interpretability. Our fully fine-tuned EfficientNetV2 B0 model sets a new standard, with a macro-average precision, recall, and F1-score of 91%, 90%, and 90%, respectively, and an average accuracy of 93%. This breakthrough underscores the transformative potential of 11-class blood cell classification for more precise medical diagnoses. Moreover, our groundbreaking "Naturalize" augmentation technique produces remarkable results. The 2K-PBC dataset generated with "Naturalize" boasts a macro-average precision, recall, and F1-score of 97%, along with an average accuracy of 96% when leveraging the fully fine-tuned EfficientNetV2 B0 model. This innovation not only elevates classification performance but also addresses data scarcity and bias in medical deep learning. Our research marks a paradigm shift in blood cell classification, enabling more nuanced and insightful medical analyses. The "Naturalize" technique’s impact extends beyond blood cell classification, emphasizing the vital role of diverse and comprehensive datasets in advancing healthcare applications through deep learning.

In the realm of the five-category classification endeavor, there has been limited exploration into applied techniques for classifying Arabic text. These methods have primarily leaned on singletask learning, incorporating manually crafted features that lack robust sentence representations. Recently, the Transformer paradigm has emerged as a highly promising alternative. However, when these models are trained using single-task learning, they often face challenges in achieving outstanding performance and generating robust latent feature representations, especially when dealing with small datasets. This issue is particularly pronounced in the context of the Arabic dialect, which has a scarcity of available resources. Given these constraints, this study introduces an innovative approach to dissecting sentiment in Arabic text. This approach combines Inductive Transfer (INT) with the Transformer paradigm to augment the adaptability of the model and refine the representation of sentences. By employing self-attention SE-A and feed-forward sub-layers as a shared Transformer encoder for both the five-category and three-category Arabic text classification tasks, this proposed model adeptly discerns sentiment in Arabic dialect sentences. The empirical findings underscore the commendable performance of the proposed model, as demonstrated in assessments of the Hotel Arabic-Reviews Dataset, the Book Reviews Arabic Dataset, and the LARB dataset.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

Repeated exposure to pathogens leads to evolutionary selection of adaptive traits. Many species transfer immunological memory to their offspring to counteract future immune challenges. Transfer factor such as that found in colostrum is among the many mechanisms where transfer of immunologic memory from one generation to the next can be achieved for enhanced immune response. Here, a library of 100 plants with high protein contents were screened to find plant-based proteins that behave like a transfer factor moiety to boost human immunity. Aqueous extracts from candidate plants were tested on a human peripheral blood mononuclear cell (PBMC) cytotoxicity assay using human cancerous lymphoblast cells - K562 cells as a target and Natural Killer cells as an effector. Plant extracts that caused PBMCs to exhibit enhanced killing beyond the capability of the colostrum-based transfer factor were considered hits. Primary screening yielded an 11% hit rate. Protein content of these hits were tested by Bradford Assay and Coomassie stained-SDS-PAGE, where three extracts were confirmed to have high protein contents. Plants with high protein contents underwent C18 column fractionation using methanol gradients followed by membrane ultrafiltration to isolate proteins with molecular weight <3 kDa, 3-30 kDa, and >30 kDa fractions. It was found that the 3-30 kDa and >30 kDa fractions had high activity in the PBMC cytotoxicity assay. The 3-30 kDa ultrafiltrates from the top two hits, seeds from Raphanus sativus and Brassica juncea, were then selected for protein identification by mass spectrometry. The majority of the proteins in the fractions were found to be seed storage proteins, with low abundance of proteins involved in plant defense and stress response. These findings suggest that Raphanus sativus or Brassica juncea extracts could be considered for further characterization and immune functional exploration with a possibility of supplemental use to bolster recipients’ immune response.

Age-related myelination decrease is considered one of the likely mechanisms of cognitive decline. The present study is based on the longitudinal assessment of global and regional myelination of the normal adult human brain using the fast macromolecular fraction (MPF) mapping. Additional markers were age-related changes in white matter (WM) hyperintensities on FLAIR-MRI and the levels of anti-myelin autoantibodies in serum. Eleven healthy subjects (33–60 years in the first study) were scanned twice, 7 years apart. An age-related decrease in MPF was found in global WM, GM, and mixed WM-GM, as well as in 48 out of 82 examined WM and GM regions. The greatest decrease in MPF was observed for the frontal WM (2-5%), genu of the corpus callosum (CC) (4.0%) and caudate nucleus (5.9%). The age-related decrease in MPF significantly correlated with an increase in the level of antibodies against myelin basic protein (MBP) in serum (r = 0.69 and r = 0.63 for global WM and mixed WM-GM, correspondingly). The volume of FLAIR hyperintensities increased with age but did not correlate with MPF changes and the levels of anti-myelin antibodies. MPF mapping showed high sensitivity to age-related changes in brain myelination, providing the feasibility of this method in clinics.

This paper studies a multihop amplify-and-forward (AF) simultaneous wireless information and power transfer (SWIPT) relaying system. Each relaying node harvests energy using power splitting (PS) scheme from a part of its received signal to amplify and forward the rest the received signal to the next relay. Based on this system model and signal flow, we derived and solved the convex energy minimization problem with optimal PS ratio. The influence of processing cost was then investigated for the AF-SWIPT system with the decode-and-forward SWIPT as benchmark, where AF-SWIPT was found to be superior.

The decline in assisted reproductive technology (ART) success among older women, attributed to decreased oocyte quantity and quality, poses a significant challenge. Currently, no consensus ex-ists on the optimal ovarian stimulation protocol for older women undergoing IVF. This retrospec-tive registered cohort study aimed to compare cumulative live birth rates (CLBR), time to live birth (TTLB), and cost-effectiveness in women over 35 years using gonadotropin-releasing hor-mone agonist (GnRHa) or clomiphene-primed ovarian stimulation (CPOS). We performed pro-pensity score matching (PSM) on 2,871 IVF cycles in women over 35 who received either GnRHa or CPOS protocols, resulting in 375 cycles in each group to compare treatment outcomes. Addition-ally, a decision tree model was utilized to assess the cost-effectiveness of the two protocols. Fol-lowing PSM, both groups showed similar baseline characteristics. The CPOS protocol exhibited a higher cycle cancellation rate (13.07% vs 8.00%, p=0.032), yet maintained comparable fertilization and embryo quality. While CLBRs per initial cycle (41.07% vs. 45.33%, p=0.269) and delivery out-comes were similar between the groups after a 24-month follow-up, TTLB was longer in the CPOS group. Notably, the average cost per live birth in the CPOS group was 21.27% less than that in the GnRHa group (￥32,301.42 vs ￥39,174.22). In conclusion, for women over 35 undergoing IVF, the CPOS protocol demonstrated similar CLBR to GnRHa but with lower costs, suggesting its potential as a viable and cost-efficient ovarian stimulation option.

The present review critically examines the advancements in the past 5 years concerning the re-search on the bioavailability of the nanoplastics (NPLs) to freshwater plankton. With a specific emphasis on two bioavailability components: uptake availability and toxico-availability, we dis-cuss the recent progress in the understanding of the adsorption, absorption, trophic transfer and biological effects in phyto- and zooplankton induced by NPLs exposure. The influence of the plankton on the NPLs bioavailability via excretion of the biomolecules and formation of eco-corona is also examined. In spite of the important research developments, there are still con-siderable knowledge gaps with respect to NPLs biouptake and trophic transfer by plankton, as well as a potential adverse effect in natural aquatic systems. As plankton play a critical role in primary production, nutrient cycling and food web structure, understanding the interaction be-tween NPLs and plankton is essential in assessing the potential implications of the nanoplastics pollution for aquatic ecosystem biodiversity and services.

Fine-tuning is an important technique in transfer learning that has achieved significant success in tasks that lack training data. However, as it is difficult to extract effective features for single-source domain fine-tuning when the data distribution difference between the source and the target domain is large, we propose a transfer learning framework based on multi-source domain called adaptive multi-source domain collaborative fine-tuning to address this issue. This approach utilizes multiple source domain models for collaborative fine-tuning, thereby improving the model's feature extraction capability in the target task. Specifically, this approach employs an adaptive multi-source domain layer selection strategy to customize appropriate layer fine-tuning schemes for the target task among multiple source domain models. The objective is to extract more efficient features. Furthermore, a novel multi-source domain collaborative loss function is designed to facilitate the precise extraction of target data features by each source domain model. Simultaneously, it works towards minimizing the output difference among various source domain models, thereby enhancing the adaptability of the source domain model to the target data. In order to validate the effectiveness of the proposed the adaptive multi-source domain collaborative fine-tuning framework, it is analyzed and compared with the most widely used fine-tuning methods by applying them to seven publicly available visual categorization datasets commonly employed in transfer learning. Experimental results demonstrate that, in comparison with the existing fine-tuning approaches, our method not only enhances the accuracy of feature extraction in the model but also provides precise layer fine-tuning schemes for the target task, resulting in state-of-the-art performance.

Zn_0.9Mg_0.1O nanoparticle (NP) were employed as electron transport layers (ETLs) with varying thicknesses to investigate their influence on the efficiency of the top-emission quantum dot light-emitting diodes (TE-QLEDs) fabricated inside the bank. An increase in the thickness of the Zn_0.9Mg_0.1O NP ETL led to a decrease in the concentration of oxygen vacancies, reducing the conductivity of the Zn_0.9Mg_0.1O and resulting in lower current density in the TE-QLEDs. The decrease in conductivity of Zn_0.9Mg_0.1O NP ETL was confirmed through electron-only device (EOD) characterization. Furthermore, it was noted that when the thickness of Zn_0.9Mg_0.1O NP ETL was 30 nm, the concentration of hydroxyl species reached its minimum. By minimizing the presence of hydroxyl species, exciton quenching at the quantum dot (QD) and Zn_0.9Mg_0.1O NP ETL interface was minimized, enhancing charge balance within the QD, significantly improving the efficiency of QLED. We successfully demonstrated that TE-QLED with a 30 nm-thick Zn_0.9Mg_0.1O NP ETL exhibits outstanding performance, achieving a maximum current efficiency of 91.92 cd/A and a maximum external quantum efficiency of 21.66%. These results suggest that Zn_0.9Mg_0.1O NP ETL, when tailored to an appropriate thickness, can serve as an ETL for TE-QLEDs, effectively suppressing exciton quenching and enhancing the charge balance in the TE-QLEDs.

In our previous published papers, considering 3 large atomic gravitational constants assumed to be associated with weak, strong and electromagnetic interactions, we have proposed the existence of a nuclear charge of magnitude, e_n=2.95e and developed a nuclear mass formula associated with strong and weak interactions having 4 simple terms and only one energy coefficient. Two important assumptions are, there exists a weak fermion of rest energy 585 GeV and strong coupling constant is the squared ratio of electromagnetic charge and nuclear charge. The aim of this paper is associated with understanding the mystery of quantum of magnetic flux, Planck’s quantum radiation constant and Reduced Planck’s constant. Proceeding further, quark charges, strong coupling constant, nuclear stability, nuclear binding energy, medium and heavy atomic X-ray levels and celestial magnetic moments can be understood in a unified approach. It may also be noted that, by considering integral nature of elementary particle masses, it seems possible to understand the discreteness of angular momentum. Considering our proposed e_n=2.95e=3e as a characteristic nuclear charge, it seems possible to understand the integral nature of quarks electromagnetic charge. With this idea, neutron, proton and pions decay can be understood very easily. In all the cases, up quark of charge (±2e) seems to play a crucial role with the internal transformation of down quark of charge (±e) and external observable elementary basic elementary particles. It needs further study at fundamental level.

Computer vision is a powerful technology that has enabled solutions in various fields by analyzing visual attributes in images. One field that has taken advantage of computer vision is agricultural automation, which promotes high-quality crop production. The nutritional status of a crop is a crucial factor in determining its productivity. This status is mediated by approximately 14 chemical elements acquired by the plant, and their determination plays a pivotal role in farm management. To address the timely identification of nutritional disorders, this study focuses on the classification of three levels of phosphorus deficiencies through individual leaf analysis. The methodological steps include: (1) generating a database with laboratory-grown maize plants that were induced to total phosphorus deficiency, medium deficiency, and total nutrition, using different capture devices; (2) processing the images with state-of-the-art transfer learning architectures (i.e. VGG16, ResNet50, GoogLeNet, DenseNet201, and MobileNetV2); and (3) evaluating the classification performance of the models using the created database. The results show that the VGG16 model achieves superior performance, with 98% classification accuracy. However, the other studied architectures also demonstrate competitive performance and are considered state-of-the-art automatic leaf deficiency detection tools. The proposed method can be a starting point to fine-tune machine vision-based solutions tailored for real-time monitoring of crop nutritional status.

Road-embedded inductive power transfer (IPT) systems have the potential to accelerate the electrification of the transportation sector. For these systems to be economically viable however, they need to have a similar durability and lifespan compared to that of asphalt roads. One area that has lacked investigation is thermally induced stresses in a primary IPT pad, which is caused by the increase in temperature of the pad when it is energized and the differing thermal expansion of the materials within. This paper presents an experimental and a finite-element based methodology for investigating the thermal-mechanical behaviour of a ¼-scale double-D pad, which was energized while suspended in air, as well as energized when embedded in pavement. A focus was placed on the measurement and prediction of strains in the magnetic ferrite cores because of their brittleness. Ferrite strains were measured using a combination of resistive strain gauges and non-metallic Fibre Bragg Grating (FBG) sensors. Coupled electromagnetic-thermal-structural simulations were conducted to predict temperature and strains in the system, with temperature-dependent properties obtained through physical testing. At an ambient temperature of 50°C, the temperature in the middle of the copper litz wire coil was predicted to be 100°C in both the suspended and embedded case. There was excellent correlation to experimental results, with a difference of less than 10% for most temperature measurements. When energized, the pad was predicted to experience an upward bow due to its temperature rise, resulting bending strains in the ferrite cores. At an ambient temperature of 50°C, maximum tensile strain in the ferrites of the embedded pad was measured to be 62 microstrain (με), with a root-mean square error that was 18 με across three sensors. The experimental and validated numerical methodology can be applied to full-scale operational IPT pads to analyse and improve their thermal-mechanical performance.

Mass transfer and phase transition have important effect on the velocity of bubble migration in deepwater wellbore, and accurate prediction of bubble migration velocity is crucial for calculating the safe shut-in period of deepwater oil and gas well. Therefore, the effect of bubble dissolution mass transfer and hydrate phase transition on bubble migration behavior in deepwater environment have attracted extensive attention from researchers in the fields of energy, marine chemistry, and marine engineering safety. In this work, a new model of bubble migration velocity in deepwater is developed, which considers the effect of hydrate phase transition and gas-water bidirectional cross-shell mass transfer during bubble migration. Based on the observation data of bubble migration in deepwater, the reliability of the model in predicting bubble migration velocity is verified. Then, the model is used to calculate and analyze the bubble migration velocity and bubble migration cycle under different initial bubble size, different annular fluid viscosity and density. The results show that the initial size of bubble and the viscosity of annulus fluid are the main factors affecting the migration velocity of bubble, but the density of annulus fluid has little effect on the migration velocity of hydrated bubble and clean bubble. In addition, the migration velocity of clean bubble gradually increases during the migration process from the bottom to the wellhead, while the migration velocity of hydrated bubble is divided into gradually decreasing stage and slowly increasing stage. The gas consumption and the thickening of hydrate shell in the gradually decreasing stage play a dominant role, and the increase of bubble volume caused by the decrease of pressure in the slowly increasing stage is the most important factor. The formation of hydrated bubble can significantly reduce the migration velocity of bubble and effectively prolong the safe shut-in period. This study provides a reference for quantitative description and characterization of complex bubble migration behavior with phase change and mass transfer in deepwater environment.

Widely used estimates of food-insecure populations are likely to be biased upwards, lacking adjustment for global increases in sedentary behavior in recent decades. We first construct a household model to account for sedentary choices during leisure and work time decisions. The model rationalizes increasing sedentary behavior from the household by accounting for increasing returns to cognitive human capital vs physical capital, alongside increased productivity of more sedentary activities both at work and at home. The household model then informs an empirical model that makes use of our unique international pseudo-panel data on sitting time, which serves as a proxy for sedentarism. We econometrically estimate a transfer function linking sedentarism to widely available covariates, which then are used to make out-of-sample predictions and can be applied to a large set of countries. The estimated sedentary time can be used to adjust the physical activity level reflected in the minimum dietary energy requirement used to determine a cutoff for food insecurity.

Deep Learning (DL) has made significant advances in computer vision with the advent of Vision Transformers (ViT). Unlike Convolutional Neural Networks (CNNs), ViTs use self-attention to extract both local and global features from image data, and then use residual connections to feed these features directly into a fully networked multilayer perceptron head. In hospitals, hematologists prepare peripheral blood smears (PBSs) and read them under a medical microscope to detect abnormalities in blood counts such as leukemia. However, this task is time-consuming and prone to human error. This study investigates the transfer learning process of Google ViT and ImageNet CNNs to automate the reading of PBSs. The study used two online PBS datasets, PBC and BCCD, and transferred them into balanced datasets to investigate the influence of data amount and noise immunity on both neural networks. The PBC results show that Google ViT is an excellent DL neural solution for data scarcity. The BCCD results show that Google ViT is superior to ImageNet CNNs in dealing with unclean, noisy image data because it is able to extract both global and local features and use residual connections, despite the additional time and computational overhead.

Measuring magnetic fields in the inner corona, the interface between the solar chromosphere and outer corona, is of paramount importance if we aim at understanding the energetic transformations taking place there and which is at the origin of processes that lead to coronal heating, solar wind acceleration, and of most of the phenomena relevant to space weather. However, these measurements are more difficult than mere imaging because polarimetry requires differential photometry. The Coronal Magnetograph mission (CMAG) has been designed to map the vector magnetic field, line-of-sight velocities, and plane-of-the-sky velocities of the inner corona with unprecedented spatial and temporal resolutions from space. This will be achieved through full vector spectropolarimetric observations using a coronal magnetograph as the sole instrument on board a spacecraft, combined with an external occulter installed on another spacecraft. The two spacecraft will maintain a formation flight distance of 430 meters for coronagraphic observations, which requires a 2 m occulter disk radius. The mission will be preferentially located at the Lagrangian L5 point, offering a significant advantage for solar physics and space weather research. Existing ground-based instruments face limitations such as atmospheric turbulence, solar scattered light, and long integration times when performing coronal magnetic field measurements. CMAG overcomes these limitations by performing spectropolarimetric measurements from space with an external occulter and high-image stability maintained over time. It achieves the necessary sensitivity and offers a spatial resolution of 2.5 arcseconds and a temporal resolution of approximately one minute, in its nominal mode, covering the range from 1.02 solar radii to 2.5 radii. CMAG relies on proven European technologies and can be adapted to enhance any other solar mission, offering potential significant advancements in coronal physics and space weather modeling and monitoring.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

The measures related to climate change and international technology transfer have been closely intervened as most international environmental instruments, including the United Nations Framework Convention on Climate Change and Kyoto Protocol as well as Paris Agreement which contain the provisions concerning environmentally friendly technology transfer. However, technologies have not been transferred adequately owing to the flaws in the relevant provisions and due to the fact that most technologies are possessed by transnational corporations and other private sectors. In order to undertake the commitment by the governments of developed countries and at the same time, to conform the commercial activities of their respective private sectors to the level of promised international obligation, an uniform international technology transfer agreement needs to be established separately, particularly under the World Trade Organization regime in Post Pairs-Agreement era. This paper first explores the defects and challenges found in provisions related to technology transfer in existing environmental agreements, and examines the possibilities of concluding an international technology transfer agreement both from theoretical and practical perspectives. climate change;environmentally sound technology;international technology transfer;Post Paris-Agreement Era

Pool boiling is extensively utilized in various fields, such as electronics cooling, battery cooling, nuclear power plants, and chemical processing. In the process of temperature control through boiling, the generation and transportation of bubbles play a crucial role in calculating the heat transfer capacity of the system. Therefore, it holds immense significance to gain a profound understanding of the mechanisms underlying bubble formation, growth, and detachment. Currently, numerous mechanistic explanations and empirical correlations have been proposed to elucidate various parameters of bubbles during the boiling process. These findings were considered valuable references in selecting appropriate boiling media and designing efficient heating surfaces. To comprehensively present the progress of bubble formation and heat transfer during the boiling process, the forces exerted on the bubbles was highlighted in this article. And a meticulous review on bubble force analysis and correlation formulas pertaining to various relevant parameters (e.g. nucleation sites density, bubble growth rate, detachment diameter, detachment frequency) were conducted. This review article also were expected to provide a novel foundation for further exploration of enhanced boiling heat transfer.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

This study investigates the electrical characteristics observed in n- channel and p-channel ferroelectric field effect transistor (FeFET) devices fabricated through a similar process flow with 10 nm of ferroelectric hafnium zirconium oxide (HZO) as the gate dielectric. The n-FeFETs demonstrate a faster complete polarization switching compared to the p-channel counterparts. Detailed and systematic investigations using TCAD simulations reveal the role of fixed charges and interface traps at the HZO-interfacial layer (HZO/IL) interface in modulating the subthreshold characteristics of the devices. A characteristic crossover point observed in the transfer characteristics of n-channel devices is attributed with the temporary switching between ferroelectric-based operation to charge-based operation, caused by the pinning effect due to the presence of different traps. This experimental study helps understand the role of charge trapping effects in switching characteristics of n- and p-channel ferroelectric FETs.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

We suggest a new solution to the strong CP problem. The solution is based on the proper use of the boundary conditions for the QCD generating functional integral. It obeys the principle of renormalizability of Quantum Field Theory and does not involve new particles like axions.

Conical emission is a typical nonlinear phenomenon that occurs when the femtosecond laser pulses interact with transparent media. In this work, the conical emission induced by two kinds of typical vortex beams (i.e., Laguerre-Gaussian (LG) and Bessel-Gaussian (BG) beams) in water is experimentally studied. By recording the light spots of different wavelengths on the screen, the characteristics of the conical emission induced by femtosecond vortex beams are studied. It is found that the spots of the supercontinuum induced by the two kinds of vortex beams differ greatly from each other: The spots of the supercontinuum induced by the BG beam are a set of concentric rings like a rainbow with a white center, while the whit light spot in the case of the LG beam are a circular white disk, which is different from the commonly observed white light spots. By measuring the maximum divergence angle, it is observed that the divergence angle increases with the decrease of the wavelength, while the TC merely affects the divergence angle, which is explained from the formation mechanism of conical emission in terms of self-phase modulation. We hope this work can be helpful to the understanding of interaction between the intense laser pulses and matters.

The effects of the solvent used for the active layer materials of an OLED based on TADF emitters plays a fundamental role in solution-deposited devices. This work focuses the effects on the performance of different solvents employed to fabricate a very simple two organic layer OLED based on a green TADF emitter, under the concept of host:guest matrix. From the different results of the main figures of merit, it was possible to conclude that the OLED that used toluene as solvent for the active layer reached a maximum EQE of 14%, almost the maximum already obtained for this emitter in more complex device structures. With the analysis of the charge transport processes, it was possible to establish an explanatory model for the obtained results. Through impedance spectroscopy, additional characterization about the nature of charge transport processes was carried out. With these results, it was possible to corelate the relaxation times, with the electrical properties of the active layer, and infer about the interaction between the electrical charges and the defect levels opening new possibilities to further development in the printed OLEDs.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

Machinery degradation assessment can offer meaningful prognosis and health management in-formation. Although numerous machine prediction models based on artificial intelligence have emerged in recent years, they still face a series of challenges: (1) Many models continue to rely on manual feature extraction. (2) Deep learning models still struggle with long sequence prediction tasks. (3) Health indicators are inefficient for remaining useful life (RUL) prediction with cross-operational environments when dealing with high-dimensional datasets as inputs. This research proposes a health indicator construction methodology based on a transformer self-attention transfer network (TSTN). This methodology can directly deal with the high-dimensional raw dataset and keep all the information without missing when the signals are taken as the input of the diagnosis and prognosis model. First, we design an encoder with a long-term and short-term self-attention mechanism to capture crucial time-varying information from a high-dimensional dataset. Second, we propose an estimator that can map the embedding from the encoder output to the estimated degradation trends. Then, we present a domain dis-criminator to extract invariant features from different machine operating conditions. The case studies with the FEMTO-ST bearing dataset and the Monte Carlo method for RUL prediction during the degradation process are conducted. The experiment results fully exhibited the signif-icant advantages of the proposed method compared to other state-of-the-art techniques.

Breast cancer is a common malignant tumour and studies have shown that early and accurate detection is crucial for patients. With the maturity of medical imaging and deep learning development, significant progress has been made in breast cancer classification, which greatly improves the accuracy and efficiency of classification. This review focuses on deep learning, migration learning, GAN, and lifelong learning to elaborate and summarise the important roles arising from breast cancer detection. This review also examines the dataset and labeling issues required for breast cancer classification. In conclusion, at the end of the article, we look at future directions for breast cancer classification research, including cross-migration learning, multimodal data fusion, model interpretability, and lifelong learning, and also explore how to provide personalized treatment plans for patients.

Triangles are an ever present feature in nature, which the building construction industry duly echoes. However, an exact expression intended to offer the radiant field due to any triangle in an upright or inclined position had not been identified by previous research. In this case, the author has been able to solve by direct integration, the canonical expression of radiative transfer. This result alone confers a myriad of possibilities that had been inconceivable before, for studying in detail the three-dimensional heat transfer behavior of volumes and figures in which triangles do manifest, such as fins, windows, roof-gables and louvers of various kinds. Typically, shading devices, when tilted, give rise in their extremes to rhomboidal shapes which were difficult to take into account or had to be subject to discretization and subsequent Monte Carlo methods in order to perform an approximate calculation of their emission. This implied a lengthy and inexact procedure that induced many errors and consumed computing time. We can now avoid all the former downsides due to the advances hereby presented. As the novel expression can be converted into an algorithm it will be advantageously employed for simulation. This significant finding dovetails in the intricate puzzle of radiated heat and we believe that their consequences will greatly affect the conception and design of HVAC devices, aircraft manufacturing and specifically building or lighting industries among others.

During the 1950s, the Gros Michel species of bananas were nearly wiped out by the incurable Fusarium Wilt, also known as Panama Disease. Originating in Southeast Asia, Fusarium Wilt is a banana pandemic that has been threatening the multi-billion-dollar banana industry worldwide. The disease is caused by a fungus that spreads rapidly throughout the soil and into the roots of banana plants. Currently, the only way to stop the spread of this disease is for farmers to manually inspect and remove infected plants as quickly as possible, whereas it is a time-consuming process. The main purpose of this study is to build a deep Convolutional Neural Network (CNN) using a transfer learning approach to rapidly identify fusarium wilt infections on banana crop leaves. We chose to use the ResNet50 architecture as the base CNN model for our transfer learning approach owing to its remarkable performance in image classification, which was demonstrated through its victory in the ImageNet competition. After its initial training and fine-tuning on a data set consisting of 300 healthy and diseased images, the CNN model achieved near-perfect accuracy of 0.99 and was fine-tuned to adapt the ResNet base model. ResNet50’s distinctive residual block structure could be the reason behind these results. To evaluate this CNN model, 500 test images, consisting of 250 diseased and healthy banana leaf images, were classified by the model. The deep CNN model was able to achieve an accuracy of 0.98 and an F-1 score of 0.98 by correctly identifying the class of 492 of the 500 images. These results show that this DCNN model outperforms existing models such as Sangeetha et al., 2023’s deep CNN model by at least 0.07 in accuracy and is a viable option for identifying Fusarium Wilt in banana crops.

The interactions of metal ions with fulvic acids resulted in changes in the particle size and charge. Particle size distribution was trimodal for fulvic acids, bimodal for fulvic complexes with calcium and magnesium, and copper-fulvic complexes had only one size fraction. The compensation of negative charge of carboxylic and phenolic functional groups by positive charged metal ions resulted in the increase in zeta potential which was getting closer to zero in the case of copper-fulvic complexes. However, all metal humic complexes behaved as colloidally unstable which resulted in visually observable sedimentation. Calorimetric measurements provided positive values of changes in enthalpy which indicated endothermic processes. In contrast quantum chemical calculations as well as experiments with model compounds provided negative values indicated exothermic processes. Changes in Gibbs energy were determined as negative and changes in entropy as positive which meant spontaneous processes.

Accurate and efficient medicinal plant image classification is of utmost importance as these plants produce a wide variety of bioactive compounds that offer therapeutic benefits. With a long history of medicinal plant usage, different parts of plants, such as flowers, leaves, and roots, have been recognized for their medicinal properties and are used for plant identification. However, leaf images are extensively used due to their convenient accessibility and are a major source of information. In recent years, transfer learning and fine-tuning, which use pre-trained deep convolutional networks to extract pertinent features, has emerged as an extremely effective approach for image identification problems. This study is leveraging the power of three component deep convolutional neural networks, namely VGG16, VGG19 and DenseNet201, to derive features from the input images of the medicinal plant dataset, containing leaf images of 30 classes. The models were compared and ensembled to make four hybrid models to enhance the predictive performance by utilizing the averaging and weighted averaging strategies. Quantitative experiments were carried out to evaluate the models on the Mendeley medicinal leaf dataset. The resultant ensemble of VGG19+DensNet201 with fine-tuning showcases enhanced capability in identifying medicinal plant images with an improvement of 7.43% and 5.8% compared with VGG19 and VGG16. Furthermore, VGG19+DensNet201 can outperform its standalone counterparts by achieving an accuracy of 99.12% on the test set. A thorough assessment with metrics such as accuracy, recall, precision, and f1-score firmly establishes the effectiveness of the ensemble strategy.

Subway construction is often in a complex natural and human-machine operating environment, and that complicated setting leads to subway construction more prone to safety accidents, which can cause substantial casualties and monetary losses. Thus, it is necessary to investigate the safety risks of subway construction. The existing literature on the identification and assessment of subway construction safety risks(SCSR) is susceptible to the influence of subjective factors. Moreover, although existing studies have explored the interrelationships between different risks, these studies usually analyze the interrelationships of single risks, lack the study of risk chain transfer relationships, and fail to find out the key path of risk transfer. Therefore, this paper innovatively combines text mining, association rules and complex networks to deep mine subway construction safety incident reports and explore risk transfer process. Firstly, it uses text mining technology to identify subway construction safety risk; Then, association rules are introduced to explore the causal relationships among safety risk; Finally, the key safety risk and important transfer paths of subway construction safety accidents (SCSA) are obtained based on the complex network model. Research results show that (a) improper safety management, unimplemented safety subject responsibilities, violation of operation rules, non-perfect safety responsibilities system and insufficient safety education and training are the key safety risk in SCSA; (b) two shorter key risk transfer paths in the subway construction safety network can be obtained: insufficient safety education and training→lower safety awareness→violation of operation rules→safety accidents; insufficient safety checks or hidden trouble investigations→violation of operation rules→safety accidents; (c) in the process of risk transfer, the risk can be controlled by controlling the key nodes or cutting off the transfer path. The results of the study provide new ideas and methods for SCSR identification and influence element mining, which help safety managers propose accurate subway construction safety risk control measures.

This paper proposes a position recognition method for the receiver coil by the secondary coil current. Based on the practical value of the current of the receiver coil, the position recognition of the receiver coil in the WPT system is realized. This paper proposes a 3×3 array multi-transmitter coil grouping and control logic. The mathematical model of mutual inductance between the receiver and transmitter coil at different positions on the X-Y plane is established. A method for identifying the position of the receiver coil according to the current of the receiver coil is proposed. Compared with the traditional position recognition method of the receiver coil, this method does not need to add a detection coil and position sensor and can realize the position recognition of the receiver coil on the 2D plane.

Phylogenomics has enriched our understanding of the Tree of Life. Non-vertical modes of evolution—such as hybridization/introgression and horizontal gene transfer—deviate from a strictly bifurcating tree model, mirroring a network-like or reticulate structure. Here, we present an overview of a phylogenomic workflow for inferring organismal histories, calibrating those histories to evolutionary time, and detecting reticulate evolution. Mitigating analytical sources of error facilitates accurate reconstructions of evolutionary history and, in turn, characterization of non-vertical modes of evolution. Workflows and methods discussed herein may aid in the rigorous inference of organismal histories in geologic time and reticulation, providing a clearer understanding of the evolutionary process.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

The unsupervised domain-adaptive vehicle reidentification approach aims to transfer knowledge from a labeled source domain to an unlabeled target domain, however there are knowledge differences between the target domain and the source domain. To reduce domain differences, existing unsupervised domain-adaptive rerecognition methods generally require access to the source domain data to assist in re-training the target domain model. But for security reasons, in many cases, data between different domains cannot communicate. To this end, this paper proposes an unsupervised domain-adaptive vehicle re-identification method based on source-free knowledge transfer. First, by constructing a passive domain knowledge migration module, the target domain is consistent with the source domain model output to train a generator to generate the "source-like samples". Then, it can effectively reduce the model knowledge difference and improve the model generalization performance. According to the experiment and testing of VeRi776 and VehicleID, two mainstream public data sets in this field, the rank-k and mAP indexes obtained are both improved, and are suitable for object re-recognition tasks without source data.

Agriculture is one of the indispensable fields for the survival of mankind. Potatoes also have a significant role in the field of agriculture. The quality and quantity of potatoes are significantly impacted by several diseases, such as early blight and late blight, and manual interpretation of these leaf diseases is time-consuming and inconvenient. Fortunately, leaf appearance is used to detect diseases in potato plants. Productivity will considerably rise if the infections are detected early. Different types of image processing methods and machine learning methods are used for early recognition of those diseases from leaf images so that the product losses are decreased significantly. For the incredible and marvelous performance of CNN, it is the most popular deep learning method that is used immensely for the recognition of leaf diseases from images. Several pretrained deep learning models, such as VGG16, ResNet50, InceptionV3, MobileNetV2, Xception, and a deep learning model developed using CNN, are employed for potato leaf disease classification and recognition on the same dataset. The transfer learning technique is applied to the pretrained model and the data augmentation technique is applied to the Proposed CNN model for potato disease classification from leaf samples. Compared to pretrained models, the proposed CNN model offers the lowest loss and highest accuracy for potato leaf disease detection while using fewer parameters and layers. It achieves the best performance with a test accuracy of 99.33% compared to other Pretrained models used in the diagnosis of potato leaf disease.

"Finding fresh water in the ocean of data." is a challenge that all deep learning domains struggle with, especially in the area of hyperspectral image analysis. As hyperspectral remote sensing technology advances by leaps and bounds, there are increasing amounts of hyperspectral images(HSIs) can be available. Whereas in fact, these unlabeled HSIs are powerless to be used as material to driven a supervised learning task due to the extremely expensive labeling costs and some unknown regions. Although learning-based methods have achieved remarkable performance due to their superior ability to represent features, at the cost, these methods are complex, inflexible and tough to carry out transfer learning. In this paper, we propose the "Instructional Mask AutoEncoder"(IMAE), which is a simple and powerful self-supervised learner for HSI classification that uses a transformer-based mask autoencoder to extract the general features of HSIs through a self-reconstructing agent task. Moreover, we utilize the metric learning to perform an instructor which can direct the model focus on the human interested region of the input so that we can alleviate the defects of transformer-based model such as local attention distraction, lack of inductive bias and tremendous training data requirement. In downstream forward propagation, instead of global average pooling, we employ a learnable aggregation to put the tokens into fullplay. The obtained results illustrate that our method effectively accelerates the convergence rate and promotes the performance in downstream task.

In this study, deep neural network (DNN) and transfer learning (TL) techniques were employed to predict the viscous resistance and wake distribution based on the positions of flow control fins (FCFs) applied to containerships of various sizes. Both methods utilized data collected through Computational Fluid Dynamics (CFD) analysis. The position of the flow control fin (FCF) and hull-form information were utilized as input data, and the output data included viscous resistance coefficients and components of propeller axial velocity. The base DNN model was trained and validated using a source dataset from a 1000 TEU containership. Grid search cross-validation technique was employed to optimize the hyperparameters of the base DNN model. Then, transfer learning was applied to predict the viscous resistance and wake distribution for containerships of varying sizes. To enhance the accuracy of feature prediction with a limited amount of dataset, learning rate optimization was conducted. Transfer learning involves retraining and reconfiguring the base DNN model, and the accuracy was verified based on the fine-tuning method of the learning model. The results of this study can provide hull designers for containerships with performance evaluation information by predicting wake distribution, without relying on CFD analysis.

In the broad context of vulnerability detection, deep learning has achieved considerable progress but faces generalization challenges in multilingual environments . We introduce a novel approach named AST-FMVD, which leverages transfer learning and abstract syntax trees. By employing semantic similarity clustering and context-aware technology, the method constructs node mapping relationships between different languages, enabling zero-shot learning in vulnerability detection. The method was validated by applying Java's vulnerability detection model in the Python domain, successfully demonstrating that AST-FMVD retains the original model's detection capabilities in the target domain. In conclusion, the proposed method offers a promising solution to the inherent problems in multi-language vulnerability detection, signifying a potential leap in the application of deep learning, transfer learning, and abstract syntax trees for improved cross-domain performance.

Fertilized zygotes normally display 2 pronuclei (PN) but abnormal fertilization patterns (0, 1 or >2 PN) are daily observed in IVF labs. Multiple PN zygotes (>2) are generally discarded due to an increased risk of aneuploidy. However, the decision to transfer or not 1PN-derived embryos remains controversial. The aims of our study were to analyze the neonatal outcomes of fresh or frozen-thawed embryos derived from 1PN zygotes, and to evaluate the influence of the fertilization method. Data were retrospectively collected from cycles performed between January 2018 and December 2022. Fresh cycles were analyzed for the comparative fate of 1PN zygotes (n=1234) following conventional in vitro fertilization (cIVF; n=648) or intracytoplasmic sperm injection (ICSI; n=586), as well as the results of the 64 transfers of 1PN derived embryos (pregnancy rate (PR) and neonatal outcomes). This pregnancy follow-up was also applied to 167 transfers of frozen-thawed 1PN derived embryos. In fresh cycles, 46% of the 1PN zygotes in cIVF group gave rise to embryos of sufficient quality to be transferred or frozen (day 3 or 5/6). This rate decreased to 33% in the fresh ICSI cycles. Blastulation rate was also significantly higher in cIVF group (44%) in comparison to ICSI group (20%). The fresh embryo transfers (32 per group) allowed 7 pregnancies in the cIVF group (PR=21.9%) as compared to 4 pregnancies in the ICSI group (PR=12.5%). In the cIVF group, 4 deliveries of healthy newborns were achieved and only one in the ICSI group. In frozen/thawed cycles, 36 pregnancies were obtained out of the 167 transfers. A non-significative difference was observed between embryos derived from cIVF cycles (PR=26%) and ICSI cycles (PR=16%) with respectively 18 and 8 healthy babies born. In conclusion, we observed better outcomes for 1PN zygotes in cIVF cycles in comparison to ICSI cycles. Our center policy to transfer good quality 1PN-derived embryos allowed the birth of 31 healthy babies.

Abstract: In this study, a computational fluid dynamics (CFD) simulation was conducted to validate the CFD model with experimental data from Zimparov et.al (2012), which investigates the heat transfer performance in a spirally corrugated tube that has a twisted tape inserted. The heat transfer was then compared to a simple corrugated tube without the twisted tape and to a smooth tube with no corrugations and no twisted tape. This simulation is compared with a previous experimental study conducted by (Zimparov et al. 2012), which focuses on tubes with a height-to-diameter ratio e/Di > 0.04 and small relative pitches of the twisted tape, H/Di. The largest improvement was noticed in the tube with e/Di= 0.057 and ridge pitch-to-height ratio p/e=6.77 with a twisted tape of H/Di= 4.7. This tube is labeled 5035. Tube 5035 was found to have the most significant enhancement, hence the focus of the CFD simulation will be on this tube, and the simulation will range for Reynolds numbers, 3.5 x 103 < Re < 5.0 x 104. The focus of this simulation is the evaluation of heat transfer and friction factors; a metric was used to obtain an empirical representation of the tube’s performance. Keywords: Spirally corrugated tube; Twisted tape; Heat transfer enhancement; Friction factor; Nusselt number; Computational fluid dynamics (CFD); Star CCM+

This study compared the relative effect of two trace mineral supplementation strategies recom-mended in France for newborn beef calves. 600 calves were supplemented with 20 mg oral sele-nium (OTM group) at birth (D0) or by injection (ITM group) of a multi-mineral solution (60 mg of Zn, 10 mg of Mn, 15 mg of Cu, 5 mg of Se) on D0, D30 and D60. Mortality and the incidence rate of diseases, including diarrhea, omphalitis, pneumonia, as well as medicinal treatments, were recorded from D0 to D210. The incidence rate of omphalitis was significantly lower in the ITM group than in the OTM group (respectively 11% vs. 17%, P = 0.036). The cumulative inci-dence rate of all health troubles was lower in the ITM group than in the OTM group (P=0.007). Except for pneumonia, incidence of diarrhea (24% vs. 22%), use of oral (7% vs. 6%) or IV rehydra-tion therapy (4% vs. 2%) or use of antibiotics (43.3% vs. 38.0%) and mortality (3% vs 2%) were numerically higher in OTM group than in ITM group (n.s.). In this study, ITM supplementation is as efficient as oral supplementation regarding calves' health status. It reduces the risk of ompha-litis at the calf level effectively.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

Melanoma is widely recognized as one of the most lethal forms of skin cancer, with its incidence showing an upward trend in recent years. Nonetheless, the timely detection of this malignancy substantially enhances the likelihood of patients’ long-term survival. Several computer-based methods have recently been proposed in the pursuit of diagnosing skin lesions at their early stages. Despite achieving some level of success, there still remains a margin of error that the machine learning community considers to be an unresolved research challenge. This study presents a novel framework for the classification of skin lesions. The framework incorporates deep features to generate a highly discriminant feature vector, while also maintaining the integrity of the original feature space. Recent deep models including Darknet53, DenseNet201, InceptionV3, and InceptionResNetV2 are employed in our study for the purpose of feature extraction. Additionally, transfer learning is leveraged to enhance the performance of our approach. In the subsequent phase, the extracted feature information from the chosen pre-existing models is combined, with the aim of preserving maximum information, prior to undergoing the process of feature selection using a novel entropy-controlled grey wolf optimization (ECGWO) algorithm. The integration of fusion and selection techniques is employed to initially incorporate the feature vector with a high level of information and subsequently eliminate redundant and irrelevant feature information. The efficacy of our design is substantiated through the evaluation on three benchmark dermoscopic datasets, namely PH2, ISIC-MSK, and ISIC-UDA. In order to validate the proposed methodology, a comprehensive evaluation is conducted, including a rigorous comparison with established techniques in the field.

This article presents a comprehensive study on enhancing grid resilience through advanced forecasting and optimization techniques in the context of power outages. Power outages pose significant challenges to modern societies, affecting various sectors such as industries, households, and critical infrastructures. The research combines statistical analysis, machine learning algorithms, and optimization methods to address this issue to develop a holistic approach for predicting and mitigating power outage events. The proposed methodology involves the use of Monte Carlo simulations in MATLAB for future outage prediction, Long Short-Term Memory (LSTM) networks for forecasting solar irradiance and load profiles, and a hybrid LSTM-Particle Swarm Optimization (PSO) model to improve accuracy. Furthermore, the role of Battery State of Charge (SoC) in enhancing system resilience is explored. The study also assesses the techno-economic advantages of a grid-tied microgrid integrated with solar panels and batteries over conventional grid systems. The results highlight the potential of the proposed approach in strengthening grid resilience, reducing downtime, and fostering sustainable energy utilization.

Recent advancements in the study of the protein complex photosystem II have clarified the sequence of events leading to the formation of oxygen during the S3->S4->S0 tran-sition, wherein the inorganic Mn4Ca(µ-O)6(OHx)4 cluster finishes photo-catalyzing the water splitting reaction (Greife et al, Nature 2023, 617, 623-628; Bhowmick et al, Nature 2023, 617, 629-636) . During this final step a tyrosine radical (TyrZ), stable for a couple of milliseconds, oxidizes a cluster bound oxygen while the hydrogen bonding patterns of nearby waters shift a proton away. A treatment of this redox reaction within the context of accepted transition state theories predicts rate constants that are significantly higher than experimentally recovered values (10^12s^-1 versus 10^3s^-1). In an effort to understand this disparity, temperature dependent experiments have revealed large entropic con-tributions to the rates with only a moderate energy of activation. We suggest that the entropic source may be related to the observed proton rearrangements, and further possible near isoenergetic variations in the nearby extended h-bonding network de-laying the realization of an ‘ideal’ transition state. In the following we explore this re-lation in the context of Eyring’s transition state theory and Marcus’ electron transfer theory, and evaluate their compatibility with the experimental evidence.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

A human brain can communicate with another one’s brain using quantum entanglement. Similar particles can entangle without interaction. Sensory communication between two individuals from far distances is still not known. Former studies primarily have been performed regarding brain neurons' quantum behavior. The test was performed on two individuals far from each other. These individuals were put under the same music on the basis of brain neuroplasticity property. By activating the brain reward system, aligned thinking was time scheduled in these individuals’ brains. On the basis of entanglement, compressed information was sent and received between these two individuals.

In this study, we investigate the structural changes, electronic properties, and charge redistribution within azo-bithiophene (Azo-BT) chemisorbed monolayers under different light stimuli using density functional theory and molecular dynamics simulations. We consider two types of switches, Azo-BT and BT-Azo, with different arrangements of the Azo and BT blocks counting from the anchor thiol group. The chemisorbed monolayers of pure cis- and trans-isomers with a surface concentration of approximately 2.7 molecules per nm2 are modeled on a gold surface using classical all-atom molecular dynamics. Our results reveal significant shrinkage of the BT-Azo layer under UV illumination, whereas the thicknesses of the Azo-BT layer remain comparable for both isomers. This difference in behavior is attributed to the ordering of the trans-molecules in the layers, which is more pronounced for Azo-BT, leading to a narrow distribution of the inclination angle to the gold surface. Conversely, both layers consisting of cis-switches exhibit disorder, resulting in similar brush heights. To study charge transfer within the immobilized layers, we analyze each snapshot of the layer and calculate mean charge transfer integrals using Nelsen’s algorithm for a number of interacting neighboring molecules. Combining these integrals with reorganization energies defined for the isolated molecules, we evaluate the charge transfer rates and mobilities for electron and hole hopping within the layers at room temperature based on Marcus’ theory. This research offers new perspectives for the innovative design of electrode surface modifications and provides insights into controlling charge transfer within immobilized layers using light triggers. Additionally, we identify molecular properties that are enhanced through specific molecular design, which contributes to the development of more efficient molecular switches for various electronic applications.

A significant replacement for numerous fossil fuels is solar energy as the main type of renewable energy resource. However, solar cells need battery energy storage units to handle the intermittent and uncontrollable nature of solar energy. In this light, there is a significant market for small, portable battery charge controllers that automate battery charging. However, the issue of slow charging and premature battery life loss plagues current industry-standard or innovative battery technology. This study proposes a quick pulse charging technique that stops battery deterioration and minimizes the overall charging period. The primary goal of this study is to develop, construct, and execution of a practical, versatile, and compact photovoltaic charge controller at cut rates. The suggested charge controller can disconnect and reconnect the battery during battery overcharging and deep discharging conditions using sensors with relays. The laboratory model is tested using a less expensive PV panel, battery, and DSP controller. The charging behavior of the solar-powered PWM charge controller is studied compared to that of the Constant Voltage - Constant Current (CV-CC) method. The proposed method is pertinent for minimizing energy issues in impoverished placesat a reasonable price.

Recently, the number of vehicles on the road, especially in urban centers, has increased dramatically due to the increasing trend of individuals towards urbanization. As a result, manual detection and recognition of vehicles (i.e., license plates and vehicle manufacturer) become an arduous task and beyond human capabilities. In this paper, we have developed a system using transfer learning-based DL techniques for automatic identification of Jordanian vehicles. The YOLOv3 (You Only Look Once) model was re-trained using transfer learning to accomplish the license plate detection, character recognition, and vehicle logo detection. While VGG16 (Visual Geometry Group) model was retrained to accomplish the vehicle logo recognition. To train and test these models, four datasets have been collected. The first dataset consists of 7,035 Jordanian vehicle images, the second dataset consist of 7,176 Jordanian license plates, and the third dataset consists of 8,271 Jordanian vehicle images. These datasets have been used to train and test the YOLOv3 model for Jordanian license plate detection, character recognition, and vehicle logo detection, respectively. While the fourth dataset consists of 158,230 vehicle logo images used to train and test the VGG16 model for the vehicle logo recognition. Text measures were used to evaluate the performance of our developed system. Moreover, mean average precision (mAP) measure was used to evaluate the YOLOv3 model of the detection tasks (i.e., license plate detection and vehicle logo detection). For license plate detection, the precision, recall, F-measure, and mAP were 99.6%, 100%, 99.8%, and 99.9%, respectively. While for character recognition, the precision, recall, and F-measure were 100%, 99.9%, and 99.95%, respectively. The performance of license plate recognition stage was evaluated by evaluating these two sub-stages as a sequence, where the precision, recall, and F-measure were 99.8%, 99.8%, and 99.8%, respectively. Furthermore, for vehicle logo detection, the precision, recall, F-measure, and mAP were 99%, 99.6%, 99.3%, and 99.1%, respectively, while for vehicle logo recognition, the precision, recall, F-measure were 98%, 98%, and 98%, respectively. The performance of vehicle logo recognition stage was evaluated by evaluating these two sub-stages as a sequence, where the precision, recall, and F-measure were 95.3%, 99.5%, and 97.4%, respectively.

The variation of mutual inductance and load parameters will affect the transmission power and efficiency of the inductive power transfer (IPT) system. The identification of mutual inductance and load parameters is an essential part of establishing a stable and reliable IPT system. This paper presents a joint identification method of load and mutual inductance for LCC-S IPT system, which does not require the establishment of primary and secondary communication and related control. Firstly, the resistance-inductance characteristics of the equivalent load of the rectifier are analyzed by simulation, and then the rectifier and system load are equivalent to the circuit model of resistance and inductance in series. Secondly, the characteristics of the reflected impedance are analyzed, and the functional relationship between the transmitter impedance and the rectifier impedance is established by using the ratio of the real part to the imaginary part of the reflected impedance, which realizes the decoupling of the load and the mutual inductance. Thirdly, the functional relationship between the equivalent impedance of the rectifier and the load resistance of the system is obtained by data fitting. Then, the equations of the above two functional relationships are combined. By measuring the voltage of the parallel compensation capacitor at the transmitting side, the current of the transmitting coil and the phase difference between the two, the battery load can be solved first, and then the mutual inductance can be calculated, so that the high-precision identification of the load and mutual inductance can be realized. Finally, an experimental platform of LCC-S IPT system is built for experimental verification. The experimental results show that the maximum identification errors of mutual inductance and load are 5.20 % and 5.53 %, respectively, which proves that the proposed identification method can achieve high precision identification.

The relaxation processes induced by an exposure of the Ar matrices doped with CH4 (0.1 – 10%) to an electron beam were studied with a focus on the dynamics of radiolysis products – H atoms, H2 molecules, CH radicals, and energy transfer processes. Three channels of energy transfer to dopant and radiolysis products were discussed: by free charge carriers, free excitons and photons from the “intrinsic source” provided by emission of the self-trapped excitons. Radiolysis products along with the total yield of desorbing particles were monitored in a correlated manner. Analysis of methane transformation reactions induced by free excitons showed that the CH radical can be considered as a marker of the CH3 species. The competition between exciton self-trapping and energy transfer to the dopant and radiolysis products has been demonstrated. A nonlinear concentration behavior of the H atoms in doped Ar matrices has been established. Real-time correlated monitoring of optical emissions (H atom and CH3 radicals), particle ejection, and temperature revealed a nonmonotonic behavior of optical yields with a strong luminescence flash after almost an hour of exposure, which correlated with explosive pulse of particle ejection and temperature. The connection of this phenomenon with the processes of energy transfer and radical-radical recombination is discussed.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

Variations in threshold voltage (VTH) and charge distributions in noncircular cells of three-dimensional (3D) NAND flash memory are investigated. The electric field difference in the circular and spike regions causes nonuniform trapped electron density in the charge trap layer (CTL) and influences the VTH variation. Such less-trapped electron (LT) regions in CTL between the circular and spike regions exhibit a lower electric field during the program, resulting in a higher current flow through that region. For the two-spike cells, the charge distribution and VTH variation are analyzed at different heights (HSpike) and angles between spikes. These irregular cells decrease VTH as the HSpike increases.

One-Dimensional Solar Cell Capacitance Simulator (1D-SCAPS) and n-i-p planar configuration have been employed for the simulation of the caesium tin iodide (CsSnI₃)-based perovskite solar cell (PSC) with titanium (IV) oxide (TiO₂) and copper thiocyanate (CuSCN) as the electron and hole transport materials respectively. The results obtained for the initially modeled PSC compared well with similar devices in the literature but marred with high recombination rate. As such, the defect density in the CsSnI₃ absorber was varied from 10¹³ cm^-3 to 10¹⁷ cm^-3 and enriched with SnCl₂ (additive) and Br⁻(dopant) respectively. This strategy ensured a reduced concentration of Sn⁴⁺ vacancy (V_Sn) in the CsSnI₃ absorber with improved carrier lifetime and diffusion length beyond 0.05 ns and 1.1µm by a magnitude of the order of 10³ and 10² respectively for the enriched CsSnI₃ –based PSC. For the optimized PSC, we recorded V_OC=1.289 V, J_SC=32.60 mA.cm^-2, FF=83.56% and PCE=35.12%.

Stemming from the object overlap and undertraining from the few samples, the road dense object detection is confronted with the poor object identification performance and the inability to recognize edge objects. Based on this, one transfer learning-based YOLOv3 approach for identifying dense objects in the road has been proposed. Firstly, Darknet-53 network structure is adopted to obtain pre-trained YOLOv3 model, then the transfer training is introduced as the output layer for the special dataset of 2000 images containing vehicles; in the proposed model, one random function is adapted to intialize and optimize the weights of the transfer training model, which is seperately designed from the pre-trained YOLOv3; and the object detection classifier replaces the fully connected layer, which further improves the detection effect, the reduced size of the network model can further reduce the training and detection time, and can be better applied to actual scenarios. The experimental results demonstrate that the object detection accuracy of the presented approach is 87.75% for the Pascal VOC 2007 dataset, which is superior to the traditional YOLOv3 and the traditional YOLOv2 by 3.05% and 11.15%, respectively. Besides, the test was carried out using UA-DETRAC, a public road vehicle detection dataset, the object detection accuracy of the presented approach reaches 79.23% in detecting images, which is 4.13% better than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the detection accuracy is 1.36% better. Moreover, the detection speed of the proposed YOLOv3 method reaches 31.2 Fps/s in detecting images, which is 7.6 Fps/s faster than the traditional YOLOv3, and compared with the existing relatively new object detection algorithm YOLOv5, the speed is 4.3 Fps/s faster; the proposed YOLOv3 performs 79.38Bn of floating point operations per second in detecting video, which obviously surpasses the traditional YOLOv3 and the newer object detection algorithm YOLOv5.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

This study presents a comprehensive investigation of entropy generation during natural convection in a porous medium with Casson fluid. The governing equations, including the momentum, energy, and entropy balance equations, are solved numerically using finite element method. Through the analysis, various parameters affecting entropy generation are investigated, such as the Casson fluid parameter, Radiation, Prandtl number, and Rayleigh number. The results indicate that the Casson fluid parameter significantly influences the flow and heat transfer characteristics, while the Darcy number and Rayleigh number control the intensity of natural convection. Moreover, the Prandtl number determines the relative significance of heat transfer compared to viscous effects.

Electrophysiological mapping (EM) using acute electrode probes is a common procedure performed during functional neurosurgery. Due to their constructive specificities, the EM probes are lagging in innovative enhancements. This work addressed complementing a clinically employed EM probe with carbonic and circumferentially segmented macrocontacts that are operable both for neurophysiological sensing ("recording") of local field potentials (LFP), and for test stimulation. The paper illustrates in-depth the development, that is based on direct writing of functional materials. The unconventional fabrication processes were optimized on planar geometry and then transferred to the cylindrically thin probe body. We report and discuss on the constructive concept and architecture of the probe, characteristics of the electrochemical interface deduced from voltammetry and chronopotentiometry, and the results of in vitro and in vivo recording and pulse stimulation tests. Two and three directional macrocontacts were added on probes having shanks of 550 and 770 m diameters and 10-23 cm lengths. The graphitic material presents a ~2.7 V-wide, almost symmetric water electrolysis window, and an ultra-capacitive charge transfer. When tested with 150 s biphasic current pulses, the interfacial polarization stayed safely away from the water window for pulse amplitudes up to 9 mA (135 C/cm2). The in vivo experiments on adult rat models confirmed the high-quality sensing of LFPs. Additionally, the in vivo-prevailing increase of the electrode impedance and overpotential are discussed and modeled by an ionic mobility-reducing spongiform structure; this restricted diffusion model gives new applicative insight into the in vivo-uprisen stimulation overpotential.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

The inherent dependency of deep learning models to labeled data is a well-known problem and one of the barriers that slows down the integration of such methods into different fields of applied sciences and engineering, in which experimental and numerical methods can easily generate a colossal amount of unlabeled data. This paper proposes an unsupervised domain adaptation methodology that mimics the peer review process to label new observations in a different domain from the training set. The approach evaluates the validity of a hypothesis using domain knowledge acquired from the training set through a similarity analysis, exploring the projected feature space to examine the class centroid shifts. The methodology is tested on a binary classification problem, where synthetic images of cubes and cylinders in different orientations are generated. The methodology improves the accuracy of the object classifier from 60% to around 90% in the case of a domain shift in physical feature space without human labeling.

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

The gut microbiota's part in colon cancer has become an exciting and hopeful area of study because it shows complex links that affect how cancer starts, spreads, and responds to treatments. Dysbiosis, which is an imbalance in the community of germs in the gut, has been linked to a higher risk of colon cancer by causing inflammation and making a place where tumours can grow. Researchers have found that some kinds of bugs can either help colon cancer grow or stop it from doing so. This shows how important it is to maintain a healthy gut bacteria. In both preclinical and clinical research, therapeutic treatments that target the microbiome in the gut have shown promise. Probiotics and prebiotics can change the environment around a tumour, change the balance of microorganisms in the gut, and boost immune responses that fight the cancer. Faecal microbiota transfer (FMT) is being looked at as a new way to change the bacteria in the guts of people with colon cancer. By adding microbiota-targeted drugs to standard cancer treatments, it may be possible to make the treatment more effective and lessen side effects. Microbiota-focused treatments for colon cancer are still in their early stages, but they show promise. More research needs to be done to find out how they work and show that they work in the clinic. The link between the bacteria in the gut and colon cancer opens up new ways to help patients and give them better results. This might make a difference in how colon cancer is handled in the future.

The unique characteristics of frescoes on overseas Chinese buildings can attest to the integration and historical background of Chinese and Western cultures. Reasonable analysis and preservation of overseas Chinese frescoes can provide sustainable development for culture and history. This research adopts the image analysis technology based on artificial intelligence, and proposes a ResNet-34 model and method integrating transfer learning. This deep learning model can identify and classify the source of the frescoes of the emigrants, and can effectively deal with the problems such as the small number of fresco images on the emigrants' buildings, poor quality, difficulty in feature extraction, and similar pattern text and style. The experimental results show that the training process of the model proposed in this article is stable. On the constructed Jiangmen and Haikou fresco JHD datasets, the final accuracy is 98.41%, and the recall rate is 98.53%. The above evaluation indicators are superior to classic models such as AlexNet, GoogLeNet, and VGGNet. It can be seen that the model in this article has strong generalization ability and is not prone to overfitting. It can effectively identify and classify the cultural connotations and regions of frescoes.

The entropy and charge distributions have been calculated for a simple model of polyelectrolytes attached to the surface of DNA using a field-theoretic method that includes fluctuations to the lowest one-loop order beyond mean-field theory. Experiments have revealed correlation-driven behavior of DNA in charged solutions, including charge inversion and condensation. In our model, the condensed polyelectrolytes are taken to be doubly charged dimers of length comparable to the distance between sites along the phosphate chains. Within this lattice-gas model, each adsorption site is assumed to have either a vacancy or a positively-charged dimer attached with the dimer oriented either parallel or perpendicular to the double helix DNA chain. We find that the inclusion of the fluctuation terms decreases the entropy by ∼50% in the weak binding regime. There, the bound dimer concentration is low because the dimers are repelled from the DNA molecule, which competes with the chemical potential driving them from the solution to the DNA surface. Surprisingly, this decrease in entropy due to correlations is so significant that it overcompensates for the entropy increase at the mean field level, so that the total entropy is even lower than in the absence of interactions between lattice sites. As a bonus, we present a transparent exposition of the methods used that could be useful to students and others wishing to use this formulation to extend this calculation to more realistic models.

The petroleum industry produces thousands of barrels of oilfield waters from the initial stage driven by primary production mechanisms to the tertiary stage. These produced waters contain measurable amounts of oil in water emulsions, the exact amounts being determined by the chemistry of the crude oil. To meet strict environmental regulations governing the disposal of such produced waters, demulsification to regulatory permissible levels is required. Within the electric double layer theory, coupled with the analytical solutions to the Poisson Boltzmann Equation, continuum electrostatics approaches can be used to describe the static and electrokinetic properties of such emulsion systems. Therefore, theoretical understanding of the stability of oil in water emulsions within such fundamental concepts provides reliable approaches to demulsification. In this paper, we have used theoretical approaches, based on zeta potential and surface charge density models to determine the stability of oil in water emulsions for different crude oil samples. Accordingly, we have used literature based data on the chemistry of the crude oils, and have ranked the order of emulsion stability based on criterial established by zeta potential plots for the oil. Our theoretical calculations show that where the isoelectric points of crude oil samples are closer to each other, the degree of ionization plots versus pH indicate close tends for salinities at varying pH of oilfield waters. Based on the chemistry of crude oil samples, the most efficient and cost-effective means of demulsification is by reducing produced water pH to values closer to the average point of zero charge pH values

In order to improve the charge collection efficiency, we simulated and experimentally tested the doping structure of the electron multiplication layer in EBCMOS. In this paper, we simulate the charge collection efficiency of EBCMOS under different doping methods by modeling the collisional scattering of electrons with solid atoms in semiconductor materials and combining the transport trajectories of electrons in the electron multiplication layer, the simulation results indicate that using a layered doping structure to reduce the thickness of the index heavily doped layer can effectively optimize the electric field distribution in the electron multiplier layer and reduce the recombination rate of electrons. The optimized doping structure has a significant effect on improving charge collection efficiency. Based on the simulation results, doped samples were prepared and tested. The test results showed that the charge collection efficiency obtained under the condition of a P-type silicon substrate thickness of 7μm and an index heavily doped layer thickness of 1μm was 72.65%, reducing the thickness of the index heavily doped layer to 0.1μm, the charge collection efficiency obtained can reach 86.27%, which proves that reducing the thickness of the index heavily doped layer can effectively improve the charge collection efficiency of EBCMOS devices.

Bone metastasis detection and quantification on bone scintigraphy is challenging and clinical important for treatment and patient’s life quality. To develop a CNN based diagnostic system for automated segmentation on bone metastasis regions is non-trivial, especially for a small dataset. A dataset in house comprising 100 breast cancer patients and 100 prostate cancer patients is utilized for this research. The Double U-Net model is adapted through the integration of background removal, adding negative samples, and transfer learning methods for bone metastasis detection. The performance is investigated via 10-fold cross-validation and computed in pixel-wise scale. The best model we achieved has precision of 63.08%, sensitivity of 70.82%, and F1-score of 66.72%. The developed system has the potential to provide pre-diagnostic reports for physicians in final decisions and the calculation of the bone scan index (BSI) with the combination with bone skeleton segmentation.

Chatbots are computer programs that use artificial intelligence to imitate human conversations. Recent advancements in deep learning have shown interest in utilizing language transformers, which do not rely on predefined rules and responses like traditional chatbots. This study provides a comprehensive review of previous research on chatbots that employ deep learning and transfer learning models. Specifically, it examines the current trends in using language transformers with transfer learning techniques to evaluate the ability of Arabic chatbots to understand conversation context and demonstrate natural behavior. The proposed methods explore the use of AraBERT, CAMeLBERT, AraElectra-SQuAD, and AraElectra (Generator/Discriminator) transformers, with different variants of these transformers and semantic embedding models. Two datasets were used for evaluation: one with 398 questions and corresponding documents, and another with 1395 questions and 365,568 documents sourced from Arabic Wikipedia. Extensive experimental works were conducted, evaluating both manually crafted questions and the entire set of questions, using confidence and similarity metrics. The experimental results showed that the AraElectra-SQuAD model achieved an average confidence score of 0.6422 and an average similarity score of 0.9773 on the first dataset, and an average confidence score of 0.6658 and similarity score of 0.9660 on the second dataset. The study concludes that the AraElectra-SQuAD model consistently outperformed other models, displaying remarkable performance, high confidence, and similarity scores, as well as robustness, highlighting its potential for practical applications in natural language processing tasks for Arabic chatbots. The study suggests that the AraElectra-SQuAD model can be further enhanced and applied in various tasks such as chatbots, virtual assistants, and information retrieval systems for Arabic-speaking users. By combining the power of transformer architecture with fine-tuning on SQuAD-like large data, this trend demonstrates its ability to provide accurate and contextually relevant answers to questions in Arabic.

The G-NUMEN array is the future gamma spectrometer of the NUMEN experiment (Nuclear Matrix Element for the Neutrinoless double beta decay), to be installed around the object point of the MAGNEX magnetic spectrometer at the INFN-LNS laboratory.. This project aims at exploring Double Charge Exchange (DCE) reactions in order to obtain crucial information about the neutrinoless double beta decay (0νββ). The primary objective of the G-NUMEN array is to detect the gamma rays emitted from the de-excitation of the excited states populated via DCE reactions with good energy resolution and detection efficiency, amidst a background composed of transitions from competingreaction channels with far higher cross-sections. To achieve this, the G-NUMEN signalswill be processed in coincidence with those generated by the detection of the reaction ejectiles in the MAGNEX Focal Plane Detector(FPD). Under the expected experimental conditions, G-NUMEN detectors will operate at high counting rates, of the order of hundreds of kHz per detector, while maintaining excellent energy and timing resolutions. The complete array will consist of over 100 LaBr3(Ce) scintillators. Initial tests have been conducted on the first detectors of the array, allowing for the determination of their performance at high rates.

A series of derivatives, involving two dithienylethene (DTE), groups, connected by several molecular linkers (bis(ethylene-1,2-dithiolato)Ni- (NiBDT), naphthalene, quasilinear oligothiophene chains) are investigated with the aid of computational quantum chemistry methods. This involves the computation of the second- and third-order nonlinear optical properties, i.e. molecular hyperpolarizabilities of the designed/selected derivatives. These properties can be efficiently controlled by DTE switches, in connection with light of appropriate frequency. We found that NiBDT, as a linker, is associated with a greater contrast, in comparison to naphthalene, between the first and second hyperpolarizabilities of the “open-open” and the “closed-closed” isomers. This is explained by invoking the low lying excited states of NiBDT. It has been found that the second hyperpolarizability can be used as an index, which follows the structural changes induced by photochromism. The two-photon absorption, which is related to the imaginary part of second hyperpolarizability, has also been investigated for the S0S1 transition. Furthermore, the intramolecular excited-state energy transfer (EET) is studied as well as the overlap between the absorption and emission spectra of the donor and acceptor groups of the molecules. The electronic coupling, VDA, between the donor and acceptor fragments, as well as the emission spectrum of the donor and the absorption spectrum of the acceptor have been computed, assuming a Förster type transfer mechanism. EET is a critical factor governing the photochromism. Two methods were used to compute VDA, one based on linear response and one based on the distributed multipole analysis (DMA); both techniques give very similar results for the dominating Coulomb contribution. For NiBDT as the linker a low VDA value has been computed. We found that VDA is affected by the molecular geometry. Our results clearly show that the linker strongly influences the communication between the open-closed DTE groups and thus, photochromism. The present computations show that full photochromism is attained in derivatives where two DTE groups are linked by a tetrathiophene chain, in agreement with experiment. The sensitivity of molecular linear and nonlinear optical properties upon photochromism can assist with the identification of the molecular isomers.

Understanding how industrial agglomeration affects agricultural green production efficiency is essential for green agricultural development. This study uses the super-efficient EBM-GML to measure and analyze the spatial and temporal evolution characteristics and core sources of dynamics of agricultural green production efficiency in China by using panel data from 30 Chinese provinces from 2006 to 2020. It also empirically investigates the relationships between industrial agglomeration, land transfer, and agricultural production efficiency. By using fixed, intermediary, and threshold effects models, the internal links between the industrial agglomeration, land transfer, and agricultural green production efficiency are examined. The findings indicate that the green production efficiency of Chinese agriculture exhibits the regional characteristics of being “high in the west and low in the east, high in the south and low in the north” in terms of space; in terms of time series, the overall trend is that of growing, with an average annual growth rate of 11.45%, and the growth primarily depends on the “single-track drive” of green technological progress. By promoting land transfer, industrial agglomeration can increase the agricultural green production efficiency and decomposition index. Land transfer has a double-threshold effect on the influence of industrial agglomeration on agricultural green production efficiency. As a result, this study suggests adhering to the idea of synergistic development, promoting agricultural green development, strengthening the development of industrial agglomerations, promoting the quality and efficiency of industry, improving land-transfer mechanisms, and placing a focus on resource efficiency improvements, as well as other policy recommendations.

This research is a preliminary phase of a general effort to develop a generic-data transferring capability via human haptic thermal sensation (generic-data refers to a coded language like Morse or Braille). For the capability to be effective, it must include a large variety of short recognizable cues. Hence, we propose the concept of cues based on sequences of thermal pulses, i.e., combinations of warm and cool pulses with several levels of intensity. The objective of this study was to determine the feasibility of basing a generic-data-transfer capability on thermal cues composed of sequences of short pulses. The research included defining the basic characteristics of the stimuli parameters and developing practical methods for generating and measuring them. Several sequences were designed in light of the relevant data known to date, and tests were conducted. The thermal cues presented to the participants were sensed and recognized by touch. The results indicate high feasibility for a capability that is applicable in various scenarios. In addition, the low impact on human skin temperature due to short stimuli duration represents an inherent advantage for later implementation. This report presents promising findings and offers insights for further investigation.

Nowadays, with the development of laser weapons, the primary power supply of laser weapons puts forward more and more high demand for its performance. The pulsed power supply based on conventional homopolar inductor alternator (HIA) cannot meet the requirements any more. In order to improve the power density and efficiency, this paper proposes applying the high-temperature superconducting (HTS) HIA with slotless stator core to this power supply. In this paper, the design considerations of it are presented, and the comparisons between the two power supplies are discussed. The calculation results show that the power supply based on HTS machine has much larger power density than the conventional HIA, and the efficiency is also larger than the conventional HIA. This can improve the performance of laser weapons dramatically.

This publication describes the influence of residue monomers in synthesized pressure-sensitive adhesives based on acrylics on main performance such as tack, peel adhesion, shear strength and shrinkage in form of transfer tapes used for joining wooden elements in furniture industry. The discussed carrier-free adhesive tapes are synthesized by photo-crosslinking and photopolymerization with UV radiation of photoreactive prepolymers sandwiched between two adhesive siliconized polyester films. The simultaneous crosslinking and polymerization process under UV lamps carried out under UV lamps placed simultaneously above and below the crosslinked photoreactive polymer layer leads to the production of a carrier-free adhesive film. In this test series it were investigated to what how the intensity of UV radiation and the time of its exposure affect the viscosity of photoreactive compositions, and then the content of unreacted monomers in them and, subsequently, the method of their crosslinking and polymerization, and the concentration of the photoreactive crosslinking compound leading to the obtaining of transfer adhesive tapes, and thus on their tray, peel adhesion, shear strength and shrinkage on the surface of the wood.

There is only a very short reaction time for people to find the best way out of a building in a fire outbreak. Software applications can be used to assist the rapid evacuation of victims; however, this is an arduous task, which requires an understanding of advanced technologies. Since well-known pathway algorithms (such as, Dijkstra, Bellman-Ford and A*) can lead to serious problems over performance, we decided to make use of deep reinforcement learning techniques. A wide range of strategies including a random initialization of replay buffer and transfer learning were assessed in three projects involving schools of different sizes. The results showed the proposal was viable and that in most cases the performance of transfer learning was superior. In addition, the study raised challenges that had to be faced in the future.

Deep learning is improving by leaps and bounds in remote sensing images (RSIs) analysis, pre-trained convolutional neural networks (CNNs) have shown remarkable performance in remote sensing image scene classification (RSISC). Nonetheless, pre-trained CNNs require massive annotated data as samples for data training. When labeled samples are not sufficient, the most common solution is to the pre-trained CNNs using a great deal of natural image dataset (e.g. ImageNet). However, these pre-trained CNNs require a large quantity of labelled data for training, which is often not feasible in RSISC, especially when the target RSIs have different imaging mechanisms from RGB natural images. In this paper, we proposed an improved hybrid classical-quantum transfer learning CNNs composed of classical and quantum elements to classify open-source RSI dataset. The classical part of the model is made up of a ResNet network which extracts useful features from RSI datasets. To further refine the network performance, a tensor quantum circuit is subsequently employed by tuning parameters on near-term quantum processors. We tested our models on open-source RSI dataset. In our comparative study, we have concluded that the hybrid classical-quantum transferring CNN has achieved better performance than other pre-trained CNNs based RSISC methods with small training samples. Moreover, it has been proved that the proposed algorithm improves the classification accuracy while greatly decreasing sum of model parameters and sum of training data.

Background: Primary lymphedema is a chronic condition caused by a developmental abnormality of the lymphatic system and its malfunction. Different surgical options such as physiologic and excisional procedures have been proposed. The aim of this study was to present a complete algorithm for the treatment of primary lower extremity lymphedema: Primary LYmphedema Multidisciplinary Approach (P-LYMA). Methods: Nineteen patients were treated according to the P-LYMA. Patients underwent pre- and post-operative complex decongestive therapy (CDT). Different physiologic and excisional procedures were performed independently or in combination. The primary outcome was the circumferential reduction rate (CRR). The Lymphedema Quality of Life Score (LeQOLiS), reduction in the number of episodes of cellulitis, length of stay, and complications were recorded. Results: The mean CRR calculated was 72.8±19.6% after twelve months. The episodes of cellulitis per year decreased from a mean of 1.9±0.8 preoperative to 0.4± 0.6 throughtout follow-up. Two patients experienced minor complications. Mean hospitalization time was 5 days. Patients’ quality of life (LeQOLi score) drastically improved from 70.4±11.6 to 24.2 ±13.9 at twelve months post-op. Conclusion: The P-LYMA algorithm allows to maximize surgical results and improve the quality-of life in patients who suffer from primary lymphedema. CDT is mandatory to optimize results.

Gastrodia pubilabiata is a nonphotosynthetic and mycoheterotrophic orchid belonging to subfamily Epidendroideae. Compared to other typical angiosperm species, the plastome of G. pubilabiata is dramatically reduced in size to be only 30,698 base pairs (bp). This reduction has led to the loss of most photosynthesis-related genes and some housekeeping genes in the plastome, which now only contains 19 protein coding genes, three tRNAs, and three rRNAs. This study decoded the entire mitogenome of G. pubilabiata, which consisted of 44 contigs with a total length of 867,349 bp. Its mitogenome contained 38 protein coding genes, nine tRNAs, and three rRNAs. To determine possible gene transfer events between the plastome and the mitogenome, individual BLASTN searches were conducted, using all available orchid plastome sequences and flowering plant mitogenome sequences. Plastid rRNA fragments were found at a high frequency in the mitogenome. Seven plastid protein coding gene frangments (ndhC, ndhJ, ndhK, psaA, psbF, rpoB, and rps4) were also identified in the mitogenome of G. pubilabiata. Phylogenetic trees using these seven plastid protein coding gene fragments suggested that horizontal gene transfer (HGT) from plastome to mitogenome occurred before losses of photosynthesis related genes, leading to the lineage of G. pubilabiata. Compared to species phylogeny of the lineage of orchid, it was estimated that HGT might have occurred approximately 30 million years ago.

Indoor localization (IL) is a significant topic of study with several practical applications. The area of IL has evolved greatly in recent years due to the introduction of numerous technologies such as WiFi, Bluetooth, cameras, and other sensors. Despite the growing interest in this field, there are numerous challenges and drawbacks that must be addressed to develop more accurate and sustainable systems for IL and its real-life applications. This review study gives an in-depth look into IL, covering the most promising artificial intelligence-based and hybrid strategies that have shown excellent potential in overcoming some of the limitations of classic methods. In addition, the paper investigates the significance of high-quality datasets and evaluation metrics in the design and assessment of IL algorithms. Furthermore, this overview study emphasizes the crucial role that machine learning techniques, such as deep learning and transfer learning, play in the advancement of IL. A focus on the importance of IL and the various technologies, methods, and techniques that are being used to improve it. Finally, The survey highlights the need for continued research and development to create more accurate and scalable techniques that can be applied across a range of industries, such as evacuation-egress routes, hazard-crime detection, smart occupancy-driven energy reduction and asset tracking and management.

This brief communication intends to develop critical thinking on the development at different levels that could be evaluated in the well-being of humans from the local development towards a global scale or planetary point of view. Therefore it was presented and discussed how Artificial Intelligence tools could provide important contributions and influence in the design of critical thinking to develop ideas and insights within Research as well as funding for technology transfer. In this context it should be highlighted that the generation of funding and economy for sustainability that it should be based on critical thinking and analysis of what is need it from the close surrounding towards longer distances as well as in the inversed direction. In this regard, the main axes that support it are based on the importance of entailment of individuals in their close surrounding as well as to longer physical distances and cultural differences. An in this context it should be highlighted the existence of large diversity and varied Multicultural differences. These factors could affect the developments of technology, education; level, and quality of life. Thus the Economical and development indexes could be largely varied and different between them. For this reason it should highlighted the local development within shortened times by interacting to receive or provide materials with aggregated value or non-tangible values. Therefore, it could be accelerated the process of improvement in a targeted field looking for average homogeneous development everywhere. And there, it is where the link-up and transfer strategies of technology and education by creation of varied strategies in communication media. As for example the communication plays an important role to transfer knowledge within the different social status and imagining the development of thinking that later it will be the basis for the next generation of technology. By this manner, it could be coupled different levels of educations degrees by a factor in common related with curiosity and open minds to learn, work, and live together in the context of developments of new smart manners of living where economy and new encrypted currency are involucred and provide by different manners sustainability. In these perspectives the development and education at the University and higher degrees taking into account the transmission of important factors such as; i) entailment , ii) development of knowledge, and iii) transference, is fundamental. Finally, it should be highlighted the particular need of good human relationships, emotional intelligence, and diplomacy to afford from the simplest challenges to the higher ones.

This study investigates the influence of expectations and trust on farmers' decisions regarding contractual choices in land transfer. The dataset used for analysis consists of 1101 households in Guizhou Province. The research focuses on two aspects: the selection between written and oral contracts, and the decision to continue the contractual relationship. The findings reveal that farmers' choices are significantly affected by their expectations and levels of trust.Specifically, when farmers' expectations regarding the land transfer process are not met, they tend to prefer written contracts over oral ones. This preference can be attributed to the greater clarity and risk reduction offered by written contracts. On the other hand, higher levels of trust increase the likelihood of farmers continuing the land transfer contract, as trust fosters a sense of confidence and security in the ongoing relationship.Interestingly, trust also plays a moderating role. Farmers who have aligned expectations and high levels of trust are more inclined to opt for oral contracts. This preference for oral contracts can be attributed to their flexibility and emphasis on interpersonal relationships, allowing for better adaptation to the changing dynamics of land transfer.These findings contribute to a deeper understanding of the factors influencing farmers' decision-making processes regarding contractual choices in land transfer. They provide valuable insights for policymakers involved in land transfer, enabling them to optimize policies and facilitate farmers' decision-making processes.

Compliant amplifying mechanisms are used widely in high-precision instruments driven by piezoelectric actuators, and the dynamic and static characteristics of these mechanisms are closely related to instrument performance. Although the majority of existing research has focused on analysis of their static characteristics, the dynamic characteristics of the mechanisms affect their response speeds directly. Therefore, this paper proposes a comprehensive theoretical model of compliant amplifying mechanisms based on the multi-body system transfer matrix method to analyze the dynamic and static characteristics of these mechanisms. The effects of the main amplifying mechanism parameters on the displacement amplification ratio and the resonance frequency are analyzed comprehensively using the control variable method. An iterative optimization algorithm is also used to obtain specific parameters that meet the design requirements. Finally, simulation analyses and experimental verification tests are performed. The results indicate the feasibility of using the proposed theoretical compliant amplifying mechanism model to describe the mechanism’s dynamic and static characteristics, which represents a significant contribution to the design and optimization of compliant amplifying mechanisms.

The phenomenon of seat occupancy in university libraries is a prevalent issue. However, existing solutions, such as software-based seat reservations and sensors-based occupancy detection, have proven to be inadequate in effectively addressing this problem. In this study, we propose a novel approach: a serial dual-channel object detection model based on Faster RCNN. Furthermore, we develop a user-friendly web interface and mobile APP to create a computer vision-based platform for library seat occupancy detection. To construct our dataset, we combine real-world data collection with UE5 virtual reality. The results of our tests also demonstrate that the utilization of personalized virtual dataset significantly enhances the performance of the convolutional neural network (CNN) in dedicated scenarios. The serial dual-channel detection model comprises three essential steps. Firstly, we employ Faster RCNN algorithm to determine whether a seat is occupied by an individual. Subsequently, we utilize an object classification algorithm based on transfer learning, to classify and identify images of unoccupied seats. This eliminates the need for manual judgment regarding whether a person is suspected of occupying a seat. Lastly, the web interface and APP provide seat information to librarians and students respectively, enabling comprehensive services. By leveraging deep learning methodologies, this research effectively addresses the issue of seat occupancy in library systems. It significantly enhances the accuracy of seat occupancy recognition, reduces the computational resources required for training CNNs, and greatly improves the efficiency of library seat management.

Microbial fuel cells (MFCs) offer sustainable solutions for various biotechnological applications and are a crucial area of research in biotechnology. MFCs can effectively treat wastewater and biodiesel waste by decomposing organic matter and generating electricity. Certain Pseudomonas species possess extracellular electron transfer (EET) pathways, enabling them to transfer electrons from organic compounds to the MFC's anode. Moreover, Pseudomonas species can grow under low oxygen conditions, which is advantageous considering that the electron transfer process in an MFC typically leads to reduced oxygen levels at the anode. This study focuses on evaluating MFCs inoculated with a new Pseudomonas species, grown with 1 g.L-1 glycerol, a common byproduct of biodiesel production. Pseudomonas sp. BJa5 exhibited a maximum power density of 39 mW.m-2. Also, the observed voltammograms and genome analysis indicate the potential production of novel redox mediators by BJa5. Additionally, we investigated the bacterium's potential as a synthetic biology non model chassis. Through testing various genetic parts, including constitutive promoters, replication origins, and cargos using pSEVA vectors as a scaffold, we assessed the bacterium's suitability. Overall, our findings offer valuable insights into utilizing Pseudomonas spp. BJa5 as a novel chassis for MFCs. Synthetic biology approaches can further enhance the performance of this bacterium in MFCs, providing avenues for improvement.

Antibiotic resistance has emerged as one of the major concerns to public human health due to issues in treatment and control of major infectious diseases. From discovery of penicillin in 1940, the antibiotic resistance originated and now developed the microorganisms as resistive strains to the major available antibiotics. Furthermore, studies on this captivating activity of the microbes provide insight into the complexities of microbial physiology and may offer some guidance in preventing the onset and consequent development of antibiotic resistance. Despite of initiatives taken in last few decades to overcome the issues, the trends of antibiotic resistance gained much peak. Antibiotic resistance appears to have emerged as a result of various factors including antibiotics being misused and overused in both the medical field and the agricultural sector. Important factors in the development of antibiotic resistance also include bacterial mutation, unplanned evolution, and horizontal gene transfers. In addition, antibiotics resistance imposed the financial consequences to public health and drug development research. Future advancements related to innovative antibiotics and molecular drug designing become challenge for researchers due to intensive multiple antibiotics resistance among human population. Many researches have been conducted on origin, evolutionary aspect of antibiotic resistance and mechanisms of antibiotics resistance, but its effect on future drug development is little understood. Therefore, the recent review will highlight the role of antibiotic resistance in drug designing and impacts of antibiotic resistance on drug development in future.

Mechanochemical technology is developing rapidly, judging by the scientific information in both basic and applied studies. However, many issues and points of view remain to be discussed. This review presents some new key issues for the optimization of mechanochemical processes in theoretical and practical aspects. Emphasis is placed on powder technology aspects, which are not always discussed compared to functional or microscopic viewpoints. The transfer of chemical species across the interparticle interface between organic and inorganic species during the mechanosynthesis of nanocomposite oxides offers many new possibilities, which are discussed here in detail. Since all material transport is preceded by charge transfer, its driving force has been searched for using terminology beyond the well-established electrochemical ones. The role of organic compounds during the whole process is emphasized, regardless of their survival in the final product. The similarity with the pharmaceutical phenomena is pointed out, although its mentality is very different from that of the synthesis of nanocomposites. Not only for the rational amorphization of the active pharmaceutical ingredient, but also for the stabilization of molecular dispersion states with the participation of excipients are discussed. The effects of liquids, either added or formed by mechanochemical auto-liquefaction, are presented with reference to the comparison between wet and dry grinding. Finally, mechanisms of apparent stabilization of mechanically activated states of products are elucidated to investigate the practical applicability of mechanochemically synthesized products