In this work a modified version of the well-known Simple Water Balance (SWB) model, comprising here three parameters instead of one, was used. Although simple, the model was tested in large-scale river basins in east-central Greece, upstream two hydrometric stations. The available historic runoff records comprised 19 hydrologic years each, on a monthly basis. Thirteen among them were used for calibrating the model, whereas the six subsequent, for validating it. Two different efficiency criteria were used as a measure of performance of the modified model. Their values, calculated for both calibration and validation stages, were close and relatively high. Thus, keeping in mind both the size and complexity of the river basins studied, one can conclude that the modified model, despite its simplistic concept and lumped form, fits satisfactorily the historic runoff series.

Atmospheric propagational phase variations are the dominant source of error for InSAR timeseries analysis, generally exceeding uncertainties from poor SNR or signal correlation. The spatial properties of these errors have been well studied, but their temporal dependence and correction have received much less attention to date. We present here an evaluation of the magnitude of tropospheric artifacts in derived time series after compensation using an algorithm that requires only the InSAR data themselves. The level of artifact reduction equals or exceeds that from many weather model based methods, while avoiding the need to access fine-scale atmosphere parameters globally at all times. Our method consists of identifying all points in an InSAR stack with consistently high correlation, and computing, then removing, a fit of the phase at each of these points with respect to elevation. Comparison with GPS truth yields a reduction of 3, from an rms misfit of 5-6 cm to ~2 cm over time. This algorithm can be readily incorporated into InSAR processing flows without need for outside information.

Objectives Independent validation of risk scores after hip fracture is uncommon, particularly for evaluation of outcomes other than death. We aimed to assess the Nottingham Hip Fracture Score (NHFS) for prediction of mortality, physical function, length of stay and postoperative complications. Design Analysis of routinely collected prospective data partly collected by follow-up interviews. Setting and Participants Consecutive hip fracture patients were identified from the Northumbria hip fracture database between 2014-2018. Patients were excluded if they were not surgically managed or if scores for predictive variables were missing. Methods C-statistics were calculated to test the discriminant ability of the NHFS, Abbreviated Mental Test Score (AMTS), and ASA grade for in-hospital, 30- and 120-day mortality, functional independence at discharge, 30-days and 120-days, length of stay, and postoperative complications. Results We analysed data from 3208 individuals, mean age 82.6 (SD 8.6). 2192 (70.9%) were female. 194 (6.3%) died during the first 30-days, 1686 (54.5%) were discharged to their own home, 211 (6.8%) had no mobility at 120-days, 141 (4.6%) experienced a postoperative complication. The median length of stay was 18 days (IQR 8-28). For mortality, c-statistics for the NHFS ranged from 0.68-0.69, similar to ASA and AMTS. For postoperative mobility, the c-statistics for the NHFS ranged from 0.74-0.83, similar to AMTS (0.61-0.82) and better than the ASA grade (0.68-0.71). Length of stay was significantly correlated with each score (p<0.001 by Jonckheere-Terpstra test); NHFS and AMTS showed inverted U-shaped relationships with length of stay. For postoperative complications, c-statistics for NHFS (0.54-0.59) were similar to ASA grade (0.53-0.61) and AMTS (0.50-0.58). Conclusions and Implications The NHFS performed consistently well in predicting functional outcomes, moderately in predicting mortality, but less well in predicting length of stay and complications. There remains room for improvement by adding further predictors such as measures of physical performance in future analyses.

As part of the Copernicus programme of the European Union (EU), the European Space Agency (ESA) has developed and is currently operating the Sentinel-2 mission that is acquiring high spatial resolution optical imagery. This paper provides a description of the calibration activities and the current status of the mission products validation activities. Measured performances, from the validation activities, cover both Top-Of-Atmosphere (TOA) and Bottom-Of-Atmosphere (BOA) products. Results presented in this paper show the good quality of the mission products both in terms of radiometry and geometry and provide an overview on next mission steps related to data quality aspects.

This paper provides an overview of modelling and simulation methods for complex systems, including queuing and life support systems. To realize and capture every aspect of a system or situation, a model is used in place of the actual one. Using a model and simulation, we may create scenarios and make decisions. Computer experiments with the model can save costs, time, and effort once its validity has been shown. A model of the thing under study is created by computer simulation, which then runs the model on a digital computer and examines the results. It's interesting to note that a knowledge base of data includes information about predicted behaviour of the model as well as coordinated determination of external variables and parameters. Selecting the precise model creation technique is the first and most difficult task in simulation. A review of techniques used in simulation model execution (serial and parallel discrete-event simulation), simulation model analysis (calibration, validation, verification, goal-seeking), and conceptual, declarative, functional, constraint, and multimodal design are presented in this paper.

In recent years, the concept of Fiducial Reference Measurements (FRM) has been developed to highlight the need for precise and well-characterised measurements tailored explicitly to the post-launch calibration and validation (Cal/Val) of Earth observation satellite missions. The confidence that stems from robust unambiguous uncertainty assessment of space observations is fundamental to assessing the changes in the Earth system and climate model prediction, and delivering the essential evidence-based input for policy makers and society striving to mitigate and adapt to climate change. The underlying concept of an FRM has long been a core element of a Cal/Val program, providing a ‘trustable’ reference against which performance can be anchored or assessed. The ‘FRM’ label was created to embody into such a reference a set of key criteria. These criteria included the establishment of documented evidence of uncertainty with respect to a community-agreed reference (ideally SI-traceable) and specific tailoring to the needs of a satellite mission. It, therefore, facilitates comparison and interoperability between products and missions in a cost-efficient manner. CEOS Working Group Cal/Val (WGCV) is now putting in place a framework to assess the maturity and compliance of a ‘Cal/Val reference measurement’ in terms of a set of community-agreed criteria which define it to be of CEOS-FRM quality. The assessment process is based on a maturity matrix that provides a visual assessment of the state of any FRM against each of a set of given criteria; making visible where it is mature and where evolution and effort needs to be done. This paper provides the overarching definition of what constitutes an FRM and introduces the new CEOS FRM assessment framework.

The surface electromyogram (sEMG)--based gesture recognition to the development of intelligent prostheses has emerged as a promising avenue for upper limb amputees. However, the temporal variations in sEMG have rendered recognition models less efficient than anticipated. Cross-session calibration and training data indicate the capacity to reduce this variation. The impact of varying calibration and training data amounts on gesture recognition performance for amputees is still unknown. To assess these effects, we present four datasets for the evaluation of calibration data and examine the impact of training data volume on benchmark performance. Two amputees who had undergone amputations years prior were recruited and seven sessions of data were collected for analysis from each of them. The experimental results show that the calibration data improved the average accuracy per subject by 3.03% and 6.16%, respectively, compared to the baseline results. Moreover, it was found that to collect training data for modeling, boosting the number of training sessions proves more efficient than increasing the number of trials within a single session. Two potentially effective strategies are proposed in light of this research to enhance the cross-session models further. We consider these findings to be of the utmost importance for the commercialization of intelligent prostheses, as they demonstrate the criticality of gathering calibration and cross-session training data, as well as offer effective strategies for maximizing the utilization of the entire dataset.

In factory automation systems, hybrid wired/wireless networks are often deployed to connect devices of difficult reachability such as those mounted on mobile equipment. A widespread version of these networks makes use of Access Points (APs) to implement wireless extensions of Real--Time Ethernet (RTE) networks via the IEEE 802.11 Wireless LAN (WLAN). Unfortunately, APs may introduce random delays in packet forwarding, mainly related to the their internal behaviors (e.g. code processing times) that negatively impact on the whole performance of the automation systems. Consequently, the knowledge of these delays represent a crucial design information. This paper presents an original and effective method to measure the delays introduced by APs, exploiting a hybrid loop-back link and a simple set-up with moderate instrumentation requirements. The method, which requires an initial calibration by means of a reference AP, has been successfully tested on some commercial APs. As it will be shown, the proposed measurement procedure is general and, as such, can be profitably adopted in even different scenarios.

To assist Java programming learning of novice students, we have developed the web-based Java programming learning assistant system (JPLAS). JPLAS provides several types of exercise problems to cultivate code reading/writing skills at various levels. In JPLAS, the code writing problem (CWP) asks a student to write a source code that will pass the test code given in the assignment where the correctness is verified by running them on JUnit. In this paper, to reduce the teacher load at marking process, we present the answer code validation program that verifies all the source codes from a lot of students for each assignment at a time and reports the number of passing tests for each source code in the CSV file. Besides, to test a source code with various input data, we implement the test data generation algorithm that identifies the data type, generates a new data, and replaces it for each test data in the test code. Furthermore, to verify the correctness of the implemented procedure in the source code, we introduce the intermediate state testing in the test code. For evaluations, we applied the proposal to source codes and test codes in a Java programming course in Okayama university, Japan, and confirmed the validity and effectiveness.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

MultiCal is an affordable, high-precision measuring device designed for the on-site calibration of industrial robots. Its design features a long measuring rod with a spherical tip that is attached to the robot. By restricting the rod’s tip to multiple fixed points under different rod orientations, the relative positions of these points are accurately measured beforehand. A common issue with MultiCal is the gravity deformation of the long measuring rod, which introduces measurement errors into the system. This problem becomes especially serious when calibrating large robots, as the length of the measuring rod needs to be increased to enable the robot to move in a sufficient space. To address this issue, we propose two improvements in this paper. Firstly, we suggest the use of a new design of the measuring rod that is lightweight yet has high rigidity. Secondly, we propose a deformation compensation algorithm. Experimental results have shown that the new measuring rod improves calibration accuracy by 20% to 39%, while by using the deformation compensation algorithm, the accuracy increases by 6% to 16%. In the best configuration, the calibration accuracy is similar to that of a measuring arm with a laser scanner, producing an average positioning error of 0.274 mm and a maximum positioning error of 0.838 mm. The improved design is cost-affordable, robust, and has sufficient accuracy, making MultiCal a more reliable tool for industrial robot calibration.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

The satellite Earth observation (EO) sector is burgeoning with hundreds of commercial satellites being launched each year, delivering a rich source of data that could be exploited for societal benefit. Data streams from the growing constellation of commercial satellites are of variable quality, limiting the potential for their combined use in science applications that need long time-series data from multiple sources. The quality of calibration performed on optical sensors onboard many satellite systems is highly variable due to calibration methods, sensor design, mission objective, budget, or other operational constraints. A small number of currently operating well-characterised satellite systems with onboard calibration, such as Landsat-8/9, Sentinel-2, and planned future missions like the NASA Climate Absolute Radiance and Refractivity Observatory (CLARREO) Pathfinder, the European Space Agency (ESA) Traceable Radiometry Underpinning Terrestrial and Helio Studies (TRUTHS), and LIBRA from China, are considered benchmarks for optical data quality due to their traceability to international measurement standards. This paper describes the concept of a space-based transfer calibration radiometer called the Satellite Cross-Calibration Radiometer (SCR) that would enable the calibration parameters from satellites such as Landsat-8/9, Sentinel-2, or other benchmark systems to be transferred to a range of commercial optical EO satellite systems while in orbit. A description of the key characteristics of the SCR to successfully operate in orbit and transfer calibration from Reference systems to Client systems is presented. A system like the SCR in orbit could complement SI-Traceable satellites (SITSats) to improve data quality and consistency and facilitate the interoperable use of data from multiple optical sensor systems for delivering higher returns on the global investment in EO.

In this paper, we propose two novel methods for robot-world/hand-eye calibration and provide a comparative analysis against six state-of-the-art methods. We examine the calibration problem from two alternative geometrical interpretations, called hand-eye and robot-world-hand-eye, respectively. The study analyses the effects of specifying the objective function as pose error or reprojection error minimization problem. We provide three real and three simulated datasets with rendered images as part of the study. In addition, we propose a robotic arm error modeling approach to be used along with the simulated datasets for generating a realistic response. The tests on simulated data are performed in both ideal cases and with pseudo-realistic robotic arm pose and visual noise. Our methods show significant improvement and robustness on many metrics in various scenarios compared to state-of-the-art methods.

In bioprocess engineering the Qualtiy by Design (QbD) initiative encourages the use of models to define design spaces. However, clear guides on how models for QbD are validated are still missing. In this review we provide a comprehensive overview about validation methods, mathematical approaches and metrics currently applied in bioprocess modeling. The methods cover analytics for data used for modeling, model training and selection, measures for predictiveness and model uncertainties. We point out general issues in model validation and calibration for different types of models and put this into context of existing health authority recommendations. This review provides the start-point for developing a guidance for model validation approaches. There is no one-fits-all approach but this review shall help to identify the best fitting validation method or combination of methods for the specific task and type of bioprocess models that is developed.

(1) Background: This study aims to validate the use of Bloom's revised taxonomy as an instrument for the design of assessment tests; (2) Methods: A validation has been carried out by external judges, as well as by teachers and students, validating the instrument by means of Aiken's V; (3) Results: Judges, teachers and students consider Bloom's revised taxonomy as an effective tool for the design of assessment tests; (4) Conclusions: Using Bloom's revised taxonomy as a model for designing assessment tests promotes learning.

An innovative mobile Lidar device, developed to monitor volcanic plumes during explosive eruptions at Mt. Etna (Italy) and analyze the optical properties of volcanic particles was upgraded in October 2023 with the aim to improve volcanic plume retrievals. The new configuration of the lidar allows to obtain new data of both the optical and the microphysical properties of the atmospheric aerosol. In fact, after its upgrade, the lidar has the possibility to measure 3β, 2α and 2δ in a configuration defined as “state of the art lidar” where properties such as the particle size distribution and refractive index can be derived. During the lidar implementation we were able to to test the system performance through specific calibration measurements. In this work, the first measurement results are shown and compared with results obtained by other instruments aimed at proving the ability of the upgraded system to more precisely characterize the aerosol optical and microphysical properties.

This paper presents the prelaunch radiometric calibration of the Ozone Monitor Suite - Nadir (OMS-N) instrument, a vital payload on the FY-3F satellite. FY-3F achieved a successful launch on August 3, 2023. The radiance calibration of the OMS-N instrument was achieved using an integrating sphere, with known exit radiance ascertained through a transferring radiometer. The calibration model incorporates six energy levels. The Solar Simulator Standard System was employed to validate the calibration results, selecting specific rows to represent varying spatial dimensions. Considering the influence of xenon lamp characteristic peaks and transmission errors during the calibration process, the average deviation remained within 2.3% for the UVIS channel, 3% for the UV1 channel, and 2.2% for the UV2 channel. Furthermore, this study analyzed the uncertainty of the radiometric calibration. The results indicated an absolute uncertainty of 2.32% for both UV1 and UV2 channels, while the VIS channel exhibited an uncertainty of 1.67%. The relative uncertainty was 1.84% for both UV1 and UV2 channels, with the VIS channel exhibiting an uncertainty of 1.45%. The obtained calibration coefficients are accurate and reliable and can be used for the inversion of product parameters, which is of great significance to the quantitative application of satellite data and the advancement of scientific research on quantitative remote sensing.

In recent years, semiconductor survey meters have been developed and are in increasing demand worldwide. This study aimed to investigate whether it is possible to calculate the time constant of the semiconductor survey meter using the X-ray equipment installed in each medical facility and whether it is possible to calibrate the semiconductor survey meter. Attach an additional filter to the medical X-ray system to satisfy the standards of N-60 to N-120, add more copper plates from there, and calculate the first and second half-value layers to compare with N-60 to N-120 values. Next, we will measure the leakage dose using a medical X-ray system and calculate the time constant of the survey meter. The survey meter is then calibrated and compared with the calibration factors in industrial X-ray system. Per experimental results, it is possible to reproduce the N-60 to N-120 radiation quality using a medical X-ray system and to calculate the time constant from the measured results assuming actual leakage dosimetry using that radiation quality. We also found that the calibration factor was equivalent to that of an industrial X-ray device. It was revealed that semiconductor survey meters can be calibrated using a medical X-ray system.

A partial aperture onboard calibration method can solve the onboard calibration problems of some large aperture remote sensors, which is of great significance for the development trend of increasingly large apertures in optical remote sensors. In this paper, the solar diffuser reflectance degradation monitor (SDRDM) in the onboard calibration assembly (CA) of the FengYun-4 (FY-4) advanced geostationary radiance imager (AGRI) is used as the reference radiometer for measuring the partial aperture factor (PAF) for the AGRI onboard calibration. First, the linear response count variation relationship between the two is established under the same radiance source input. Then, according to the known bidirectional reflection distribution function (BRDF) of the solar diffuser (SD) in the CA, the relative reflectance ratio coefficient between the AGRI observation direction and the SDRDM observation direction is calculated. On this basis, the response count value of the AGRI and the SDRDM is used to realize the high-precision measurement of the PAF of the AGRI B1 ~ B3 bands by simulating the AGRI onboard calibration measurement under the illumination of a solar simulator in the laboratory. According to the determination process of the relevant parameters of the PAF, the measurement uncertainty of the PAF is analyzed; this uncertainty is better than 2.04% and provides an important reference for the evaluation of the onboard absolute radiometric calibration uncertainty after launch.

This review paper deals with recently proposed algorithms for distributed blind macro-calibration of sensor networks based on consensus (synchronization), not requiring any fusion center. The basic algorithm, performing the estimation of the local calibration parameters, is derived commencing from appropriate local criteria, and developing the corresponding gradient descent scheme. It is shown that the estimated parameters of the calibration functions asymptotically converge, in the mean-square sense and with probability one (w.p.1), to such values that ensure consensus on calibrated sensor gains and calibrated sensor offsets. For the more realistic case in which additive measurement noise, communication dropouts and additive communication noise are present, two algorithm modifications are introduced: one using a simple compensation term, and a more robust one based on an instrumental variable. By utilizing stochastic approximation arguments it is shown that the modified algorithms also achieve asymptotic agreement for calibrated sensor gains and offsets, in the mean-square sense and w.p.1. Convergence rate is analyzed in terms of an upper bound of the mean-square error. It is also shown that the communications between nodes can be completely asynchronous, which is of substantial importance for real-world applications. Suggestions for design of \textit{a priori} adjustable weights are given. Finally, it is shown that, if there is a subset of (precalibrated) reference sensors with fixed calibration parameters, the calibrated sensor gains and offsets of the rest of the sensors do not achieve consensus - they converge to different points dictated by the reference sensors and the network characteristics. Wide applicability and efficacy of these algorithms are illustrated on several simulation examples.

This study proposes self-calibration of capacitor mismatch errors for high-resolution pipeline analog-to-digital converters (ADCs). The proposed calibration circuit recursively amplifies the capacitor mismatch error by re-utilizing a multiplying digital-to-analog converter in a pipeline stage without increasing the circuit complexity, and the amplified error voltage is converted into digital code by utilizing the remaining pipeline stages. Error correction is performed by subtracting the digital code from the ADC output during normal operation. A prototype of a 12-bit pipeline ADC is fabricated in a 0.18 µm standard CMOS process. The ADC comprises eight 1.5-bit stages, followed by a 4-bit flash ADC as the final stage; the capacitor mismatch errors in the first two pipeline stages are corrected by utilizing the proposed self-calibration technique. At a sampling rate of 30 MS/s, the measured differential and integral nonlinearities improve from +0.82/-0.75 and +1.12/-1.79 to +0.45/-0.41 and +0.47/-0.91 after calibration, respectively. Further, the measured dynamic performances improve significantly with calibration. For an input frequency of 2.09 MHz, the ADC achieves a spurious-free dynamic range (SFDR) and signal-to-noise and distortion ratios (SNDR) of 69.3dB and 63.9dB before calibration, respectively. After calibration, the SFDR and SNDR increase to 84.1dB and 68.9dB, respectively, and the effective number of bits is approximately 11.1bit. The power consumption of the ADC is 35mW under 1.8V supply, and the resulting figure of merit is 514fJ/conversion step.

Data from NASA’s Soil Moisture Active Passive Mission (SMAP) and from the California Cooperative Oceanic Fisheries Investigations (CalCOFI) were used to examine the freshening that occurred during 2015-2016 in the Southern California Current System. Overall the freshening was found to be related to the 2014-2016 Northeast Pacific Warm Anomaly. The primary goal was to determine the feasibility of using SMAP data to observe the surface salinity signal associated with the warming. As a first step direct comparisons were done with salinity from the CalCOFI data at one-meter depth. During 2015 SMAP was saltier than CalCOFI by 0.5 PSU, but biases were reduced to < 0.1 PSU during 2016. South of 33°N, and within 100 km of the coast, SMAP was fresher in 2015 by almost 0.2 PSU. CalCOFI showed freshening of 0.1 PSU. North of 33°N SMAP and CalCOFI saw significant freshening in 2016, SMAP by 0.4 PSU and CalCOFI by 0.2 PSU. Differences between SMAP and CalCOFI are consistent with the increased stratification in 2015 and changes in the mixed layer depth.

The Geostationary Environment Monitoring Spectrometer (GEMS) onboard the Geostationary Korean Multi-Purpose Satellite 2B was successfully launched in February 2020. GEMS is a hyperspectral spectrometer measuring solar irradiance and Earth radiance in the range of 300 to 500 nm. This paper introduces the spectral calibration algorithm for GEMS, which uses a nonlinear least-squares approach. To assess the performance of the algorithm, sensitivity tests for a series of spectral parameters such as shift, spectral range for fitting, signal-to-noise ratio, spectral response function (SRF), and reference spectrum have been conducted. To improve the assessment, a synthetic GEMS spectrum using the prelaunch GEMS SRF is adopted here. The test results show that the required accuracy (0.002 nm) is achievable for the expected uncertainties of the parameters except for the SRF and the choice of high-resolution reference spectrum, which degrade the algorithm performance by an order magnitude. To mitigate the sensitivity to SRF, retrieval of in-orbit SRF using an analytic function is suggested. Finally, a few candidates for the high-resolution solar reference spectrum are prepared for testing by the instrument during in-orbit tests.

InSAR and associated analytic methods can measure surface deformation from low earth orbit with a claimed accuracy of centimeters to millimeters. The realized accuracy depends on the area being measured and on the choice of analytic method, suggesting one choose a method in response to the area being measured. Here we consider a specific fixed analytic method and compare the results it produces to measurements gathered from other means in a variety of settings. In particular we compare Sentinel-1 InSAR with GPS at the Kilauea volcano around the 2018 eruption, with GPS in the city of Arica, Chile, and with public survey data at a decommissioned tailings mine. In addition, we compare two independent Sentinel-1 InSAR analyses for a railway station in Oslo, Norway. Our goal is estimate the accuracy of a fully automated Sentinel-1 InSAR pipeline in various settings. Our conclusions are that centimeter level accuracy is a reasonable claim in many, but not all settings, and that accuracy is typically not lost by using an automated pipeline, instead of hand-selecting and tuning parameters.

Ethics is a research field that is obtaining more and more attention in Computer Science due to the proliferation of artificial intelligence software, machine learning algorithms, robot agents (like chatbot), and so on. Indeed, ethics research has produced till now a set of guidelines, such as ethical codes, to be followed by people involved in Computer Science. However, a little effort has been spent for producing formal requirements to be included in the design process of software able to act ethically with users. In the paper, we investigate those issues that make a software product ethical and propose a set of metrics devoted to quantitatively evaluate if a software product can be considered ethical or not.

YG-13A represents the highest level of Chinese SAR satellites to date. In this paper, we report on experiments conducted to improve and validate ranging accuracy with YG-13A. We analyze the error sources in the YG-13A ranging system, such as atmospheric path delay, and transceiver channel delay. A real-time atmospheric delay correction model is established to calculate the atmospheric path delay, considering the troposphere delay and ionosphere delay. Six corner reflectors (CRs) were set up to ensure the accuracy of validation methods. Pixel location accuracies of up to 0.479-m standard deviation can be achieved after a complete calibration. We further demonstrate that the adjustment of the CRs can cause a marginal loss of ranging precision. After eliminating this error, the ranging accuracy is improved to 0.237 m. For YG-13A, a single frequency GPS receiver is used and the orbital nominal accuracy is 0.3 m, which is the biggest factor restricting its ranging accuracy. Our results show that the ranging accuracy of YG-13A can achieve decimeter-level, which is lower than centimeter-level accuracy with TerraSAR-X loading a dual frequency GPS. YG-13A has great convenience in terms of access to control points and target location that does not depend on ground equipment.

Unmanned aerial vehicles (UAV) thermal imagery offers several advantages in environmental monitoring, as it can provide a low-cost, high-resolution, and flexible solution to measure the temperature of the surface of the land. Limitations related to the maximum load of the drone lead to use of lightweight uncooled thermal cameras whose internal components are not stabilized to a constant temperature. Such cameras suffer from several unwanted effects that contribute to the increase in temperature measurement error from ±0.5 °C in laboratory conditions, to ±5 °C in unstable flight conditions. This article describes a post processing procedure, that reduces the above unwanted effects. It consists of following steps: i) devignetting using single image vignette correction algorithm, ii) georeferencing of images using EXIF data, scale-invariant feature transform (SIFT) stitching, and gradient descent optimisation, and iii) temperature calibration by minimisation of bias between overlapping thermal images using gradient descent optimisation. The solution was tested in several case studies of river areas, where natural water bodies were used as a reference temperature benchmark. In all tests, the precision of the measurements was increased. The root of the mean of the Square of Errors RMSE on average was reduced by 39.0% and Mean of the absolute value of Errors MAE by 40.5%. The proposed algorithm can be called self-calibrating, as in contrast to other known solutions is fully automatic, uses only field data and does not require any calibration equipment or additional operator effort. A Python implementation of the solution is available on GitHub.

Previous camera self-calibration methods have exhibited certain notable shortcomings. On one hand, they either exclusively emphasized scene cues or solely focused on vehicle-related cues, resulting in a lack of adaptability to diverse scenarios and a limited number of effective features. Furthermore, these methods either solely utilized geometric features within traffic scenes or exclusively extracted semantic information, failing to comprehensively consider both aspects. This limited the comprehensive feature extraction from scenes, ultimately leading to a decrease in calibration accuracy. Additionally, conventional vanishing point-based self-calibration methods often required the design of additional edge-background models and manual parameter tuning, thereby increasing operational complexity and the potential for errors. Given these observed limitations, and in order to address these challenges, we propose an innovative roadside camera self-calibration model based on the Transformer architecture. This model possesses a unique capability to simultaneously learn scene features and vehicle features within traffic scenarios while considering both geometric and semantic information. Through this approach, our model can overcome the constraints of prior methods, enhancing calibration accuracy and robustness while reducing operational complexity and the potential for errors. Our method outperforms existing approaches on both real-world dataset scenarios and publicly available datasets, demonstrating the effectiveness of our approach.

The calibration of three-dimensional (3D) coordinates in augmented reality (AR) systems is a complex activity. It involves the recognition of environmental characteristics and technology that models the 3D space of the device, determining its position and orientation. In the industrial environment, it is common for AR applications to cover large spaces, making it difficult to maintain attributes such as precision and accuracy. The set of sensors and mapping algorithms available in HoloLens stimulate the development of virtual reality (VR) applications, in particular localization techniques. This study proposes calibration models of the 3D coordinates of the HoloLens for indoor industrial environments. The performance of tests in a relevant environment provides data necessary to evaluate the performance of the proposed models in terms of precision and accuracy in determining point coordinates in the study environment. The results show improvements in determining the axes that define the 3D space, with a direct influence on the position of the points observed in the experiment

Infrared sensors are applied more and more widely in industrial production applications. Based on the theory of thermal radiation, this paper discusses the system design principle, temperature calibration method and thermal image analysis method in detail. The system has passed the measurement unit certification, showing that the field of view is 180°, the number of scanning points is 2048, the linear velocity is 10-100Hz, the spatial resolution is 2.5mrad, and the precision is ±1℃. On-line monitoring test has been done in the steelmaking plant of Bao Steel. The results show that the system has strong anti-interference ability, stability and reliability, and meets the application requirements of online monitoring.

Flood Management remains a major problem in many urban environments. Commonly, catchment models are used to generate the data needed for estimation of flood risk; event-based and continuous-based models have been used for this purpose. Use of catchment models requires calibration and validation with a calibration metric used to assess the predicted catchment response against the recorded catchment response. In this study, a continuous model based on SWMM using the Powells Creek catchment as a case study is investigated. Calibration of the model was obtained using 25 selected events from the monitored data for the catchment. Assessment of the calibration used a normalised peak flow error. Using alternative sets of parameter values to obtain estimates of the peak flow for each of the selected events and different accuracy criteria, the best datasets for each of the accuracy criteria were identified. These datasets were used with SWMM in a continuous simulation mode to predict flow sequences for extraction of Annual Maxima Series for an At-Site Flood Frequency Analysis. From analysis of these At-Site Flood Frequency Analyses, it was concluded that the normalised peak flow error needed to be less than 10% if reliable design flood quantile estimates were to be obtained.

Proper calibration of eye movement signal registered by an eye tracker seems to be one of the main challenges in popularizing eye trackers as yet another user input device. Classic calibration methods taking time and imposing unnatural behavior of users have to be replaced by intelligent methods that are able to calibrate the signal without conscious cooperation with users. Such an implicit calibration requires some knowledge about the stimulus a person is looking at and takes into account this information to predict probable gaze targets. The paper describes one of the possible methods to perform implicit calibration: it starts with finding probable fixation targets (PFTs), then uses these targets to build a mapping - probable gaze path. Various possible algorithms that may be used for finding PFTs and mapping are presented in the paper and errors are calculated utilizing two datasets registered with two different types of eye trackers. The results show that although for now the implicit calibration provides results worse than the classic one, it may be comparable with it and sufficient for some applications.

An easier method for the calibration of differential drive robots is presented. Most of the calibration is done on-board and it is not necessary to expend too much time taking note of the robot's position. The calibration method does not need a big free space to perform the tests. The bigger space is just in a straight line, which is easy to find. Results with the proposed method are compared with those from UMB as a reference, and they show very little deviation while the proposed calibration is much simpler.

The Individual Work Performance Questionnaire (IWPQ) can be defined as the individual be-haviour capable of generating value and competitive advantage for the organization. It is a mul-ti-dimensional construct, consisting of task performance, contextual performance and counter-productive work behavior. Albeit important, a comprehensive measure of individual job per-formance is still lacking in the Italian context. This paper describes the validation of an Italian adaptation of the IWPQ. A back translation procedure was used. To investigate the psychometric properties of the 18-item Italian IWPQ, 1053 participants (502 men, 47.7%; 551 women, 52.3%) were enrolled; the age of participants ranged between 19 and 69 (Mage=34.6, SD= 11.8), and for the oc-cupation, the sample is classified in blue collar 32.5%, pink collar 33% and white collar 34.5%. Exploratory and confirmatory factor analyses and multigroup confirmatory factor analyses were performed to test the structural factor of the IWPQ. The results supported the goodness of the IWPQ in the Italian context and the scales were found consistent with the original structure. One item was omitted due to a low factor loading, resulting in a final 17-item structure. Multigroup confirmatory factor analysis showed that the factor solution was invariant across both gender and occupational category and found evidence of metric invariance, uniqueness and scalar invariance, and structural invariance. Convergent and discriminant validity were also tested and showed.

Virtual validation of radar sensor models is becoming increasingly important for the safety validation of adf. Therefore, methods for quantitative comparison of radar measurements in the context of model validation need to be developed. This paper presents a novel methodology for accessing and quantifying validation measurements of radar sensor models. This method uses edf and the so-called dvm to effectively quantify deviations between distributions. By applying this metric, the study measures the consistency, reproducibility and repeatability of radar sensor measurements. Different interfaces and different levels of detail are investigated. By comparing the radar signals from real world experiments where different objects are present, valuable insights are gained into the performance of the sensor. In particular, the research extends to assessing the impact of varying rain intensities on the measurement results, providing a comprehensive understanding of the sensor’s behaviour under these conditions. This holistic approach significantly advances the evaluation of radar sensor capabilities and enables the quantification of the maximum required quality of radar simulation models.

Sustainable diet behaviour is crucial in ensuring food security and healthy life with low environmental impacts, for the present and future generations. However, sustainable diet is a new concept both globally as well as in Malaysia. Therefore, this study aimed to adapt and validate a questionnaire on sustainable diet behaviours, as well as to assess the levels and willingness of sustainable diet behaviour and its association with socio-demographic characteristics among university students in a public university in Malaysia. The final questionnaire resulted in three factors (perceived effectiveness, local/ seasonal food and behavioural control). The questionnaire displayed acceptable factor loadings (0.57 - 0.79) with total variance of 50.4% in the Exploratory Factor Analysis and demonstrated relative fitness in the Confirmatory Factor Analysis. These findings showed that the adapted questionnaire was valid and could be used in the assessment of sustainable diet behaviour among young adults. In the survey, the participants showed moderate positive sustainable diet behaviour. Females and Indian participants were more likely to purchase seasonal / local foods and choose sustainable food products (p<0.05). Participants in the preparation and action stage for sustainable diet behaviour had higher scores in all three factors individually or combined. The findings should be used as the basis for future studies among the general population and intervention programs in promoting sustainable diet behaviour in the country.

Background and Objectives: The Temperament Evaluation of Memphis, Pisa, Paris and San Diego Autoquestionnaire (TEMPS-A) is designed to assess affective temperaments. The short version of TEMPS-A (TEMPS-A-SV) was translated into diverse languages for its broad application in research and clinical settings. However, no study was conducted to validate the Korean version of TEMPS-A-SV among patients with mood disorders. The purpose of this study is to examine the reliability and validity of the TEMPS-A-SV in mood disorder patients of the Korean population. Materials and Methods: In this cross-sectional retrospective study, a total of 715 patients (267 patients with major depressive disorder, 94 patients with bipolar disorder I, and 354 patients with bipolar disorder II) completed the Korean TEMPS-A-SV. Cronbach's alpha and McDonald’s omega was used to assess reliability. Exploratory factor analysis (EFA) was also performed. Spearman's correlation coefficient was used to examine associations between five temperaments. The difference in five temperament scores between gender or diagnosis groups were analyzed, and the correlation between five temperament scores and age were tested. Results: The Korean TEMPS-A-SV displayed good internal consistency (α = 0.65–0.88, ω = 0.66–0.9) and significant correlations between the subscales except one (correlation between hyperthymic and anxious). Using EFA, a two-factor structure was produced: Factor I (cyclothymic, depressive, irritable, and anxious) and Factor II (hyperthymic). The cyclothymic temperament score differed by gender and the anxious temperament score was significantly correlated with age. All the temperaments, except for irritable temperament, showed significant differences between diagnosis groups. Conclusions: Overall, our findings indicate that TEMPS-A-SV is a valid and reliable measure of estimating affective temperaments among Koreans. Our results confirm validity of TEMPS-A-SV among Korean patients with mood disorders. However, more study is required on affective temperaments and associated characteristics in people with mood disorders.

The Earth's fresh water resources predominantly is groundwater that is pumped out due to rapid urbanization and aggravated by climate change. Groundwater modeling is a crucial tool for understanding aquifer systems, employing 1D, 2D, and 3D numerical models with distinct applications. One-dimensional models focus on vertical dynamics, examining aquifer properties and simulating vertical contaminant transport. Two-dimensional models extend to regional scales, considering horizontal variations and assessing groundwater-surface water interactions, making them valuable for watershed-scale studies. Three-dimensional models provide a comprehensive representation of hydrogeological systems, capturing intricate flow patterns and aiding site-specific assessments. Comparative analysis reveals model strengths and limitations, emphasizing the importance of calibration for reliable results. Case studies showcase practical applications, such as 1D models in flooding analysis and 2D models for simulating debris flows. Three-dimensional modeling proves essential for understanding complex river-aquifer exchange fluxes. Future directions call for a global groundwater platform to address data variability and technical challenges. Despite substantial investments required, the anticipated returns in scientific advancements, societal benefits, and economic gains are expected to outweigh the initial costs. This review aims in highlighting the significance of advancing all three-dimension groundwater modeling for sustainable water resource management and environmental protection.

The Earth's water resources, totaling 1.386 billion cubic kilometers, predominantly consist of saltwater in oceans. Groundwater, plays a pivotal role, with 99% of usable freshwater supporting 1.5–3 billion people as drinking water source and 60–70% for irrigation. Climate change, with temperature increase and altered precipitation patterns, directly impacts groundwater systems, affecting recharge, discharge, and temperature. Hydrological models are crucial for assessing climate change effects on groundwater, aiding in management decisions. Advanced hydrological models, incorporating data assimilation and improved process representation, contribute to understanding complex systems. Recent studies, employ numerical models to assess climate change impacts on groundwater recharge that could help in management of Groundwater. Groundwater vulnerability assessments vary with the spatial and temporal considerations, as well as assumptions in modelling groundwater susceptibility. The review assesses the vulnerability of groundwater to climate change and stresses the importance of accurate assessments for sustainable water resource management. It highlights challenges in assumptions related to soil and aquifer properties, multiple stressors, adaptive capacity, topography, aquifer properties, and groundwater contamination processes and gradual sea level rise scenarios and realistic representations of the region of study. The advancements in hydrological modelling, including the integration of uncertainty quantification and remote sensing data, artificial intelligence, could assist in the efforts to improve models for assessing the impacts of climate change on hydrological.

In this study, Acısu Basin, which is upper side of one of the most important basins (Gediz) in Türkiye, was modelled using three types of hydrological models and three different calibration algorithms. Lumped (GR4J), semi-distributed (SWAT+), and fully distributed (mHM) hydrological models were built and integrated with Parameter Estimation Tool (PEST) which is a model independent calibration tool including various algorithms. Levenberg Marquardt (L-M), Shuffled Complex Evolution (SCE), and Covariance Matrix Adoption Evolution Strategy (CMA-ES) were selected as calibration algorithms. Calibration period was 1991-2000, and validation results were obtained for 2002-2005. The effect of model structure and calibration algorithm selection on discharge simulation was evaluated via comparison of 9 different model-algorithm combinations. Results have shown that mHM and CMA-ES combination showed the best discharge simulation performance according to NSE values (calibration: 0.67, validation: 0.60). Although statistically the model results were classified as acceptable, the pattern comparison of discharge value shows that all of the models miss the peak values in significant amounts. This problem may be related to the interventions made in 2000-2001 years interval and possible to overcome by changing the calibration and validation periods, increasing the number of iterations or using the naturalized gauge data.

Groundwater models serve as support tools to among others: assess water resources, evaluate management strategies, design remediation systems and optimize monitoring networks. Thus, the assimilation of information from observations into models is crucial to improve forecasts and reduce uncertainty of their results. As more information is collected routinely due to the use of automatic sensors, data loggers and real time transmission systems; groundwater modelers are becoming increasingly aware of the importance of using sophisticated tools to perform model calibration in combination with sensitivity and uncertainty analysis. Despite their usefulness, available approaches to perform this kind of analyses still present some challenges such as non-unique solution for the parameter estimation problem, high computational burden and a need of a deep understanding of the theoretical basis for the correct interpretation and use of their results, in particular the ones related to uncertainty analysis. We present a brief derivation of the main equations that serve as basis for this kind of analysis. We demonstrate how to use them to estimate parameters, assess the sensitivity and quantify the uncertainty of the model results using an example inspired by a real world setting. We analyze some of the main pitfalls that can occur when performing such kind of analyses and comment on practical approaches to overcome them. We also demonstrate that including groundwater flow estimations, although helpful in constraining the solution of the inverse problem as shown previously, may be difficult to apply in practice and, in some cases, may not provide enough information to significantly constrain the set of potential solutions.

We consider the problem of calibrating distance measurement of Light Detection and Ranging (lidar) sensor without using additional hardware, but rather exploiting assumptions on the environment surrounding the sensor during the calibration procedure. More specifically we consider the assumption of calibrating the sensor by placing it in an environment so that its measurements lie in a 2D plane that is parallel to the ground, and so that its measurements come from fixed objects that develop orthogonally w.r.t. the ground, so that they may be considered as fixed points in an inertial reference frame. We moreover consider the intuition that moving the distance sensor within this environment implies that its measurements should be such that the relative distances and angles among the fixed points above remain the same. We thus exploit this intuition to cast the sensor calibration problem as making its measurements comply with this assumption that “fixed features shall have fixed relative distances and angles”. The resulting calibration procedure does thus not need to use additional (typically expensive) equipment, nor deploying special hardware. As for the proposed estimation strategies, from a mathematical perspective we consider models that lead to analytically solvable equations, so to enable deployment in embedded systems. Besides proposing the estimators we moreover analyse their statistical performance both in simulation and with field tests, reporting thus the dependency of the MSE performance of the calibration procedure as a function of the sensor noise levels, and observing that in field tests the approach can lead to a ten-fold improvement in the accuracy of the raw measurements.

Human motion analysis using inertial measurement units (IMUs) has recently been shown to provide accuracy similar to the gold standard, marker-based optical motion capture, but at much lower costs and while being less restrictive and time-consuming. However, IMU-based motion analysis requires precise knowledge of the orientation in which the sensor is attached to the body segments. This knowledge is commonly obtained via an anatomical calibration procedure based on precisely defined poses or motions, which is time-consuming and error-prone. In the present work, we propose a self-calibrating approach for magnetometer-free joint angle tracking that is suitable for joints with two degrees of freedom (DoF), such as the elbow, ankle, and metacarpophalangeal finger joints. The proposed methods exploit kinematic constraints to simultaneously identify the joint axes and the heading offset. The experimental evaluation shows that the proposed methods are able to estimate plausible and consistent joint axes from just ten seconds of arbitrary elbow joint motion. Comparison with optical motion capture shows that the proposed methods yield joint angles with similar accuracy as a conventional IMU-based method while being much less restrictive. Therefore, the proposed methods improve the practical usability of IMU-based motion tracking in many clinical and biomedical applications.

This paper is a response to the EPR paper titled: "Can quantum-mechanical description of physical reality be considered complete?", published in Physical Review in 1935. A quantum-mechanical (QM) measurement function describes a distribution of local results and each empirical measurement process produces one result as exact as allowed by a measuring instrument calibrated to a non-local unit standard. Repeating these empirical measurements produces a bell shaped distribution of measurement results. Each of these distributions can be compared to the other. To precisely compare a QM measurement function describing a distribution of eigenvectors to a distribution of repetitive empirical measurement results, it is necessary to determine, by calibration, the precision of the eigenvectors to the same standard as the empirical results, because each eigenvector evidences uncertainty relative to a standard. When the calibration process is recognized as formal as well as empirical, QM measurement function results and metrology measurement process results are unified.

This study explores the use of satellite-based LULC (Land Use / Land Cover) data while simultaneously correcting potential evapotranspiration (PET) input with Leaf Area Index (LAI) to increase the performance of a physically distributed hydrologic model. The mesoscale hydrologic model (mHM) was selected for this purpose due to its unique features. Since LAI input informs the model about vegetation dynamics, we incorporated the LAI based PET correction option together with multi-year LULC data. The Globcover land cover data was selected for the single land cover cases, and hybrid of CORINE (coordination of information on the environment) and MODIS (Moderate Resolution Imaging Spectroradiometer) land cover datasets were chosen for the cases with multiple land cover datasets. These two datasets complement each other since MODIS has no separate forest class but more frequent (yearly) observations than CORINE. Calibration period spans from 1990 to 2006 and corresponding NSE (Nash-Sutcliffe Efficiency) values varies between 0.23 and 0.42, while the validation period spans from 2007 to 2010 and corresponding NSE values are between 0.13 and 0.39. The results revealed that the best performance is obtained when multiple land cover datasets are provided to the model and LAI data is used to correct PET, instead of default aspect-based PET correction in mHM. This study suggests that to minimize errors due to parameter uncertainties in physically distributed hydrologic models, adequate information can be supplied to the model with care taken to avoid over-parameterizing the model.

Phase synchronization is one of the key issues that must be addressed in the bistatic synthetic aperture radar (BiSAR) system. LuTan-1 is an innovative L-band spaceborne BiSAR mission of China. An advanced synchronization scheme is used in the LuTan-1 system. The synchronization pulses are exchanged immediately after the ending time of the radar echo receiving window and before the starting time of the next pulse repetition interval. Therefore, it can not interrupt the normal SAR data acquisition, further improving synchronization frequency and avoiding the data missing effect. In order to accurately monitor system malfunctions and compensate for the phase synchronization errors introduced by hardware system, an innovative internal calibration strategy is designed and employed in the LuTan-1 mission. The test data acquired from the ground validation system of LuTan-1 are used to demonstrate the feasibility of the proposed scheme. The results validate the effectiveness of the proposed scheme and prove the promise for its future application in LuTan-1.

Gymnophiona, the most poorly known group of extant amphibians, includes elongated limbless tetrapods, with compact ossified skulls and reduced eyes, mainly adapted to fossorial life (only the Typhlonectidae exhibits adaptations for an aquatic or semiaquatic behavior). Caecilians are poorly represented in the fossil record, and despite the low number of fossil specimens described until now (only four taxa, in addition to indeterminate fragmentary material), their fossils play a key role in the knowledge of Lissamphibia origin and evolution, as well as contribute directly to a better understanding of phylogeny, taxonomy and biogeography of extant gymnophionan taxa. These records are scattered throughout geological time (from the Jurassic to the Neogene) and space (they are represented only on North and South America and Africa). Here, we revisit the caecilian fossil record, providing a brief description of all known extinct taxa described so far, along with general remarks about their impact on systematics, time range and geographic distribution of the clade, as well as prospects for future research. Possible calibration constraints based on the caecilian fossil record are provided.

In recent years, using multispectral cameras on UAVs has provided an opportunity to capture separate bands that offer the extraction of spectral features used for early detection of diseased plants. One of the main steps in disease detection is radiometric calibration that converts digital numbers to reflectance values commonly using white reference panels. This paper focused on the necessity of radiometric calibration to distinguish disease trees in orchards based on aerial multi-spectral images. For this purpose, two study sites with various climate conditions and tree species as well as different disease types were selected where multispectral images were taken using a multirotor UAV. The impact of radiometric correction on plant disease detection was assessed in two ways: 1) comparison of separability between the healthy and diseased classes using T-test and entropy distances; 2) radiometric calibration effect on the accuracy of classification. The experimental result showed the insignificant effect of radiometric calibration on separability criteria. Furthermore, based on T-test and entropy distances criteria, NIR and R spectral features made highest distances between healthy and Greening infected citrus trees, respectively, at the first study site while NDRE and BNDVI spectral features made highest distances between healthy and peach leaf curl infected trees, respectively, at the other study site. In the second strategy, the experimental result showed that radiometric calibration had no effect on the accuracy of classification. As a result, the overall accuracy and kappa values for both un-calibrated and calibrated orthomosaic classifications of the citrus orchard were 96.6% and 0.94%, respectively, using five spectral bands as well as DVI, NDRE, NDVI and GNDVI vegetation indices using a random forest classifier. The experimental results were also similar at the other study site. Therefore, the overall accuracy and kappa values for both the un-calibrated and calibrated orthomosaic classifications were 96.1%, 0.92, respectively, using five spectral bands as well as NDRE, BNDVI, GNDVI, DVI, and NDVI vegetation indices.

Inexpensive piezoelectric diaphragms can be used as sensors to facilitate both nozzle height setting and build platform leveling in FFF (Fused Filament Fabrication) 3D printers. Tests simulating nozzle contact are conducted to establish the available output and an output of greater than 8 Volts found at 20 ºC, a value which is readily detectable by simple electronic circuits. Tests are also conducted at a temperature of 80 ºC and, despite a reduction of greater than 80% in output voltage, this is still detectable. The reliability of piezoelectric diaphragms is investigated by mechanically stressing samples over 100,000 cycles at both 20 ºC and 80 ºC and little loss of output over the test duration is found. The development of a nozzle contact sensor using a single piezoelectric diaphragm is described.

Most of the existing calibration methods for binocular stereo vision sensor (BSVS) depend on high-accuracy target with feature points that are difficult to manufacture and costly. In complex light conditions, optical filters are used for BSVS, but they affect imaging quality. Hence, the use of a high-accuracy target with certain-sized feature points for calibration is not feasible under such complex conditions. To solve these problems, a calibration method based on unknown-sized elliptical stripe images is proposed. With known intrinsic parameters, the proposed method adopts the elliptical stripes located on the parallel planes as a medium to calibrate BSVS online. In comparison with the common calibration methods, the proposed method avoids utilizing high-accuracy target with certain-sized feature points. Therefore, the proposed method is not only easy to implement but is a realistic method for the calibration of BSVS with optical filter. Changing the size of elliptical curves projected on the target solves the difficulty of applying the proposed method in different fields of view and distances. Simulative and physical experiments are conducted to validate the efficiency of the proposed method. When the field of view is approximately 400 mm × 300 mm, the proposed method can reach a calibration accuracy of 0.03 mm, which is comparable with that of Zhang’s method.

A new approach to the measurement with elastic lidar of depolarization produced by atmospheric aerosols is presented. The system uses two different telescopes: one for depolarization measurements and another for total-power measurements. The system architecture and principle of operation are described. The first experimental results are also presented, corresponding to a collection of atmospheric conditions over the city of Barcelona.

Biometric fingerprint identification hinges on the reliability of its sensors, however, calibrating and standardizing these sensors poses significant challenges, particularly in regard to repeatability and data diversity. To tackle these issues, we propose methodologies for fabricating synthetic 3D fingerprint targets, or phantoms, that closely emulate real human fingerprints. These phantoms enable the precise evaluation and validation of fingerprint sensors under controlled and repeatable conditions. Our research employs laser engraving, 3D printing, and CNC machining techniques, utilizing different materials. We assess the phantoms' fidelity to synthetic fingerprint patterns, intra-class variability, and interoperability across different manufacturing methods. The findings demonstrate that a combination of laser engraving or CNC machining with silicone casting produces finger-like shaped phantoms with high accuracy and consistency for rolled fingerprint recordings. For slap recordings, direct laser engraving of flat silicone targets excels and in the contactless fingerprint sensor setting, 3D printing and silicone filling provides the most favorable attributes. Our work enables a comprehensive, method-independent comparison of various fabrication methodologies, offering a unique perspective on the strengths and weaknesses of each approach. This facilitates a broader understanding of fingerprint recognition system validation and performance assessment.

In this paper, for the Reynolds-averaged Navier-Stokes equations, a self-closed turbulence model without any adjustable parameter is formulated and a simple model is proposed. The validation rule for self-closed turbulence model is rigorously derived from the Reynolds-averaged Navier-Stokes equation. The rule is not effected by turbulence modelling on the Reynolds stresses. As an application, two dimensional turbulent boundary layers, and plate turbulent boundary layers have been formulated.

In this analysis, we assess the performance of GSMaP-GNRT6 data in capturing precipitation climatology and climate variability across China from 2001 to 2020. The evaluation involves comparing four precipitation indices of accumulated precipitation, the number of rainy days, rainstorm days, and precipitation maximum with the daily precipitation data from 2419 stations in China. The findings reveal that the GSMaP data effectively captures the overall spatial distribution of annual, summer, and monthly precipitation. However, it exhibits minor limitations in accurately depicting the spatial distribution of the number of rainy days from July to September and the precipitation maximum during wintertime in eastern China. While the GSMaP data depicts a coherent annual cycle consistent with the station observations, a general underestimation is observed. Notably, the GSMaP data presents a much smoother annual cycle in precipitation maximum. Regarding accumulated precipitation, the number of rainstorm days, and precipitation maximum, the GSMaP data shows an almost consistent interannual variation and increasing trends, aligning with station observations. However, it is noteworthy that the magnitude of the increasing trend based on the GSMaP data is greater, especially entering the early 21st century. Conversely, a significant discrepancy in the annual variation and an almost opposite changing trend are noticed in the number of rainy days between the GSMaP data and station observations.

Women's empowerment represents a process in which they are recognized as subjects of rights. Despite advances in women's rights, inequalities persist in various areas. This study aims to validate a psychometric scale of 31 items in seven factors: Participatory Empowerment, Temerity, External Influences, Independence, Social Satisfaction and Equality. The objective is to measure the empowerment of women in the university context. The research was carried out in a transversal and non-experimental manner, with the participants' voluntary collaboration, including the participation of 1,478 university students from four Higher Education Institutions in Zone 4 of Ecuador. The data was analyzed through inferential statistics, including exploratory and confirmatory factor analysis. The results indicated that the instrument for measuring empowerment can be made up of 24 items grouped into six factors, and this model showed a good fit.

Resilience has been defined as one's competence to maintain a mental health state and overall well-being when undergoing grave stress or facing significant adversities. Numerous resili-ence-investigating research tools were developed over the years, with the Connor-Davidson Re-silience Scale (CD-RISC), a self-rated tool presenting valuable psychometric properties, remaining one of the most prominent. We aimed to translate and validate the brief CD-RISC-10 in a convenient sample of 584 nurses in Greece's secondary and tertiary health care system. We conducted a con-firmatory factor analysis and known-groups validity and estimated the reliability of the CD-RISC-10. Our confirmatory factor analysis revealed that the scale had a unifactorial structure since all the model fit indices were very good. Moreover, the reliability of the CD-RISC-10 was very good since Cronbach's alpha was 0.924 and McDonald's omega was 0.925. Therefore, the Greek version of the CD-RISC-10 confirmed the factor structure of the original one and had very good validity and reliability.

The viral nervous necrosis virus (VNNV) is the causative agent of an important disease affecting fish species cultured worldwide. Early and accurate diagnosis is at present the most effective control and prevention tool, and the molecular techniques have been strongly introduced and accepted by official organizations. Among those, real time quantitative polymerase chain reaction (rt-qPCR) is nowadays displacing other molecular techniques. However, another PCR-based technology, the droplet digital PCR (ddPCR), is on the increase. It has many advantages over qPCR, such as higher sensitivity and more reliability of the quantification. Therefore, we decided to design and validate a protocol for diagnosis and quantification of SJ and RG type VNNV, using reverse transcription-ddPCR (RT-ddPCR). We obtained an extremely low limit of detection, 10 to 100-folds lower than with RT-qPCR. Quantification by RT-ddPCR, with a dynamic range of 6.8 – 6.8 x 104 (SJ type) or 1.04 x 101 – 1.04 x 105 (RG) cps/rctn, was more reliable than with RT-qPCR. The procedure was tested and validated in field samples, providing the high clinical sensitivity and negative predictive values. In conclusion, we propose this method to substitute RT-qPCR protocols because it exceeds the expectations of qPCR in the diagnosis and quantification of VNNV.

Important current limitations of the implementation of Evidence-Based Practice (EBP) in the rehabilitation field are related to the validation process of new technologies and interventions. Indeed, most of the strict guidelines that have been developed for the validation of new drugs (i.e., double or triple blinded, strict control of the doses and intensity) cannot – or only partially – be applied in rehabilitation. Well powered high quality randomized controlled trials are more difficult to organize in rehabilitation (e.g., longer duration of the intervention in rehabilitation, more difficult to standardize the intervention compared to drugs’ validation studies, limited funding’s since not sponsorized by big pharma companies), which reduces the possibility of conducting systematic reviews and meta-analyses, as currently high level of evidence is sparse. The current limitations of EBP in rehabilitation are presented in this paper and innovative solutions are suggested such as: technology-supported rehabilitation systems, continuous assessment, pragmatic trials, rehabilitation treatment specification systems, and advanced statistical methods, to tackle the limitations to increase the quality of the research in rehabilitation. The development and implementation of new technologies should increase the quality of research and the level of evidence supporting rehabilitation provided some adaptation in our research methodology.

Novel sensing technologies for liquid biopsies offer a promising prospect for the early detection of metabolic conditions through -omics techniques. Indeed, high-field NMR facilities are routinely used for metabolomics investigations on a range of biofluids in order to rapidly recognize unusual metabolic patterns in patients suffering from a range of diseases. However, these techniques are restricted by the prohibitively large size and cost of such facilities, suggesting a possible role for smaller, low-field NMR instruments in biofluid analysis. Herein we describe selected biomolecule validation on a low-field benchtop NMR spectrometer (60 MHz), and present an associated protocol for the analysis of biofluids on compact NMR instruments. We successfully detect common markers of diabetic control at low-to-medium concentrations through optimized experiments, including glucose (≤ 2.6 mmol./L) and acetone (25 μmol./L), and additionally in readily-accessible biofluids. We present a combined protocol for the analysis of these biofluids with low-field NMR spectrometers for metabolomics, and offer a perspective on the future of this technique appealing to point-of-care applications.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Many insights into human disease have been built on experimental results in Drosophila, and research in fruit flies is often justified on the basis of its predictive value for questions related to human health. Additionally, there is now a growing recognition of the value of Drosophila for the study of rare human genetic diseases, either as a means of validating the causative nature of a candidate genetic variant found in patients, or as a means of obtaining functional information about a novel disease-linked gene when there is little known about it. For these reasons, funders in the US, Europe, and Canada have launched targeted programs to link human geneticists working on discovering new rare disease loci with researchers who work on the counterpart genes in Drosophila and other model organisms. Several of these initiatives are described here, as are a number of output publications that validate this new approach.

A very high-resolution DSM covering an area of 400km² over the Athens Metropolitan Area has been produced using Pleiades 1B 0,5m panchromatic tri-stereo images. Applied Remote Sensing and Photogrammetry tools have been used resulted in a 1x1m DSM over the study area. DSM accuracy has been evaluated by comparison with measured elevations with D-GPS and a reference DSM provided by the National Cadaster & Mapping Agency S.A. In addition, different combinations of stereo images have been prepared for further exploitation of the quality of the produced DSM by stereo vs. tri-stereo images. Results show that the produced by the tri-stereo images DSM has an RMSE of 1.17m in elevation (z), which is among the best reported in the relevant literature. Stereo based DSMs from the same sensor have worst performance to this end. Satellite Remote Sensing (SRS) based DSMs over urban areas provide the best cost-effective approach in comparison to airborne-based datasets due to high spatial coverage, lower cost and high temporal coverage. Pleiades-based high-quality DSM products can serve the domains of urban planning/climate, hydrological modelling and natural hazards, as major input for simulation models and morphological analysis at local scale.

The development of reliable Food Frequency Questionnaires (FFQs) requires detailed information about the level and variation of dietary food intake of the target population. However, these data are often limited. To facilitate the development of new high quality FFQs and validation of existing FFQs, we developed a comprehensive National Dietary Assessment Reference Database (NDARD) detailing information about the level and variation in dietary food intake of people 20-70 years old in the general Dutch population. This paper describes the methods and characteristics of the population included in the NDARD database. 1063 men and 985 women agreed to participate in this research. Dietary intake data were collected using different FFQs, web-based and telephone-based 24-hour recalls, as well as blood and urine-based biomarkers. The baseline FFQ was completed by 1647 participants whose mean BMI was 26±4 kg/m2; 1117 participants completed telephone-based recalls and 1781 participants completed web-based recalls. According to the baseline FFQ, the mean energy intake was 2051±605 kcal/day. The percentage of total energy intake from protein was 15±2 En%, from carbohydrates was 43±6 En%, and from fat was 36±5 En%. This database will enable researchers to validate existing FFQs and to develop new high quality dietary assessment methods.

The redshifted 21 cm line signal is a powerful probe of the cosmic dawn and the epoch of reionisation. The global spectrum can potentially be detected with a single antenna and spectrometer. However, this measurement requires an extremely accurate calibration of the instrument to facilitate the separation of the 21 cm signal from the much brighter foregrounds and possible variations in the instrument response. Understanding how the measurement errors propagate in a realistic instrument system and affect system calibration is the focus of this work. We simulate a 21 cm global spectrum observation based on the noise wave calibration scheme. We focus on how measurement errors in reflection coefficients affect the noise temperature, and how typical errors impact on the recovery of the 21 cm signal, especially in the frequency domain. Results show that for our example set up, a typical VNA measurement error in the magnitude of the reflection coefficients of the antenna, receiver, open cable which are 0.001, 0.001, 0.002 (linear) respectively would result in a 200 mK deviation on the detected signal, and a typical measurement error of 0.48∘, 0.78∘, 0.15∘ in the respective phases would cause a 40 mK deviation. The VNA measurement error can greatly affect the result of a 21 cm global spectrum experiment using this calibration technique, and such a feature could be mistaken for or be combined with the 21 cm signal.

Lateral vehicle control is a high importance in automated vehicles as it directly influences the vehicle’s performance and safety during operation. The Linear Quadratic Regulator (LQR) controller stands out due to its high-performance characteristics and is used in the open source for self driving functions. However, a notable limitation of the current approach is the manual calibration of LQR controllers based on the experience and intuition of the designers, leading to empirical uncertainties. To address this issue and enhance the lateral control performance, this paper concentrates on refining the LQR by employing three optimization algorithms: Artificial Bee Colony Optimization (ABC), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO). These algorithms aim to overcome the reliance on empirical methods and enable a data-driven approach to LQR calibration. By comparing the outcomes of these optimization algorithms to the manual LQR controller within an offline multibody simulation as testing platform, the study highlights the superiority of the best-performing optimization approach. Following this, the optimal algorithm is implemented on a real-time system for the full vehicle level, revealing the Model-in-the-Loop and the Hardware-in-the-Loop gap up to 78,89% with lateral velocity when we use Relative Error Criterion (REC) method to validate and 2.35m with lateral displacement when considering by maximum absolute value method.

When wood is thermally modified, several chemical reactions take place that change the chemical and physical properties of the wood. These changes correlate with the degree of modification, which is mostly a function of temperature and duration of modification, and consequently with a mass loss during this process. There is a lack of standardized quality control to verify the degree of heat treatment of wood and thus its quality. One of the possible methods to check the degree of thermal modification of a particular type of wood is thermogravimetry (TG). It is based on the assumption that processes that did not take place during thermal modification continue when the TG experiment is carried out. In this method, calibration curves have to be established based on TG measurements of standard samples that have been thermally modified at different temperatures and whose mass loss during modification is known. The calibration curves show the mass loss during the TG measurement as a function of the mass loss during the previous thermal modification. The course of thermal decomposition during the TG measurements is influenced by many parameters, such as the mass of the sample, the heating rate, the atmosphere in which the measurement takes place, and the shape of the crucible in which the sample is placed. In this paper, the influence of these parameters on the calibration curves was investigated. We have focused on oak wood. The best parameters result in a calibration curve with the largest correlation coefficient R2 and the highest slope of the line k. On this basis, we can determine the mass loss during thermal modification of unknown samples of the same wood species under the same measurement conditions.

During the hand-eye calibration process of the manipulator, the Euclidean distance error of the calibration results cannot be calculated because the true values of the hand-eye conversion matrix cannot be obtained. In this paper, a new method of projection error analysis is presented. Error analysis is carried out by using a priori knowledge that the location of AR markers is fixed in the calibration process. The coordinates of the AR marker center point are reprojected to the pixel coordinate system, and then compared with the true pixel coordinates of the AR marker center point obtained by corner detection or manual labeling in order to obtain the Euclidean distance between the two coordinates as the basis for error analysis. Experimental results show that the proposed optimization method can greatly improve the accuracy of hand-eye calibration results.

The escalating frequency and severity of global wildfires necessitate an in-depth understanding and monitoring of wildfire smoke impacts, specifically its contribution to fine particulate matter (PM2.5). We propose a data-fusion method to study wildfire contribution to PM2.5 using satellite-derived smoke plume indicators and PM2.5 monitoring data. Our study incorporates two types of monitoring data, the high-quality but sparse Air Quality System (AQS) stations and the abundant but less accurate PurpleAir (PA) sensors that are gaining popularity among citizen scientists. We propose a multi-resolution spatiotemporal model specified in the spectral domain to calibrate the PA sensors against accurate AQS measurements, and leverage the two networks to estimate wildfire contribution to PM2.5 in California in 2020 and 2021. A Bayesian approach is taken to incorporate all uncertainties and our prior intuition that the dependence between networks, as well as the accuracy of PA network, vary by frequency. We find that 1% to 3% increase in PM2.5 concentration due to wildfire smoke, and that leveraging PA sensors improves accuracy.

High-precision inertial sensors or accelerometers can provide us references of free-falling motions in gravitational field in space, and serve as the key payloads for gravity recovery missions. In this work, a systematic method of electrostatic inertial sensor calibrations for gravity recovery satellites is introduced, which is applied to and verified with the Taiji-1 mission. Taiji-1 is the first technology demonstration satellite of the ``Taiji Program in Space'', which, in its final extended phase in 2022, could be viewed as a gravity recovery satellite operating in the high-low satellite-to-satellite tracking mode. Based on the calibration principles, swing maneuvers with time span about 200 s and rolling maneuvers for 19 days were conducted by Taiji-1 in 2022. The inertial sensor's operating parameters including the scale factors, the center of mass offset vector and the intrinsic biased acceleration are precisely re-calibrated and are updated to the Taiji-1 science team. Data from one of the sensitive axis is re-processed with the updated operating parameters, and the performance is found to be slightly improved compared with former results. This approach could be of high reference value for the accelerometer or inertial sensor calibrations of the GFO, the Chinese GRACE-type mission, and the planned Next Generation Gravity Missions. This could also shed some light on the in-orbit calibrations of the ultra-precision inertial sensors for future GW space antennas because of the technological inheritance between these two generations of inertial sensors.

The Visible Infrared Imaging Radiometer Suite (VIIRS) on-board the second Joint Polar Satellite System (JPSS) completed its sensor level testing in February 2018. The JPSS-2 (J2) mission is scheduled to launch in 2022, and will be very similar to its two predecessor missions, the Suomi National Polar-orbiting Partnership (SNPP) mission, launched on 28 October 2011, and JPSS-1 (renamed NOAA-20) launched on 18 November 2017. VIIRS instrument has 22 spectral bands covering the spectrum between 0.4 and 12.6 mircron: 14 reflective solar bands (RSB), 7 thermal emissive bands (TEB), and one day-night band (DNB). It is a cross-track scanning radiometer capable of providing global measurements through observations at two spatial resolutions, 375 m and 750 m at nadir for the imaging bands and moderate bands, respectively. This paper will provide an overview of J2 VIIRS characterization methodologies and calibration performance during the pre-launch testing phases performed by the National Aeronautics and Space Administration (NASA) VIIRS Characterization Support Team (VCST) to evaluate the at-launch baseline radiometric performance and generate the parameters needed to populate the sensor data record (SDR) Look-Up-Tables (LUTs). Key sensor performance metrics include the signal to noise ratio (SNR), radiance dynamic range, reflective and emissive bands calibration performance, polarization sensitivity, spectral performance, response versus scan-angle (RVS), and scattered light response. A set of performance metrics generated during the pre-launch testing program will be compared to both the SNPP and JPSS-1 VIIRS sensors.

Nacelle-based Doppler wind lidars have shown promising capabilities to assess power performance, detect yaw misalignment or perform feed-forward control. The power curve application requires uncertainty assessment. Traceable measurements and uncertainties of nacelle-based wind lidars can be obtained through a methodology applicable to any type of existing and upcoming nacelle lidar technology. The generic methodology consists in calibrating all the inputs of the wind field reconstruction algorithms of a lidar. These inputs are the line-of-sight velocity and the beam position, provided by the geometry of the scanning trajectory and the lidar inclination. The line-of-sight velocity is calibrated in atmospheric conditions by comparing it to a reference quantity based on classic instrumentation such as cup anemometers and wind vanes. The generic methodology was tested on two commercially developed lidars, one continuous wave and one pulsed systems, and provides consistent calibration results: linear regressions show a difference of ∼ 0.5 % between the lidar-measured and reference line-of-sight velocities. A comprehensive uncertainty procedure propagates the reference uncertainty to the lidar measurements. At a coverage factor of two, the estimated line-of-sight velocity uncertainty ranges from 3.2 % at 3 m s⁻¹ to 1.9 % at 16 m s⁻¹. Most of the line-of-sight velocity uncertainty originates from the reference: the cup anemometer uncertainty accounts for ∼ 90 % of the total uncertainty. The propagation of uncertainties to lidar-reconstructed wind characteristics can use analytical methods in simple cases, which we demonstrate through the example of a two-beam system. The newly developed calibration methodology allows robust evaluation of a nacelle lidar’s performance and uncertainties to be established in order to further be used for various wind turbines’ applications in confidence.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

Background: Visual acuity (VA) assessments are crucial in ophthalmology but traditionally rely on in-clinic evaluations. The emergence of telemedicine has spurred interest in creating dependable self-administered VA tests for use beyond standard clinical environments. This study evaluates the practicality and validity of a self-administered Near VA card test against traditional Snellen and Rosenbaum Pocket Vision Screener (RPVS) methods for home monitoring and enhancing clinical workflow. Methods: In a cross-sectional study a near VA card (Hadassah Self-Visual Acuity Screener-HSVA) was developed with written and videotaped instructions for self-use. Patients with a minimal best corrected VA (BCVA) of 1.0 LogMAR in at least one eye were recruited from Ophthalmology and Optometry clinics. Outcomes included mean BCVA difference between the self-administered and those obtained by the examiner, and correlations among BCVA values obtained by Snellen, RPVS, HSVA and previous distance BCVA according to the patient electronic medical records. Results: A total of 275 participants (mean age: 42.5±19.4 years, range: 18-89 years, 47% female) were included. Test-retest reliability analysis for the HSVA demonstrated very good correlation and repeatability (n=38 patients.; Rs=1.0, P

Validation of the TROPOspheric Monitoring Instrument (TROPOMI) SIF product is a necessity to evaluate its feasibility in various applications. A few validation works have been conducted through direct comparison with in-situ SIF retrievals or cross-comparison with similar satel-lite-based SIF or vegetation index (VI) products. Nevertheless, the influence of the geolocation mismatch between the validation pixel and reference data on validation results was never con-sidered. This study, for the first time, quantifies the geolocation shift of the TROPOMI validation pixel based on a geometric location matching method and then the uncertainty caused by the ge-olocation mismatch. The results indicate that the geolocation shift of the TROPOMI pixel shows large temporal variations, with a standard deviation of 2.45 km and 1.96 km in the across- and along-track directions. The mean shifts are 0.07 km and 0.25 km in the across- and along-track directions respectively, indicating eastward shifts in the across-track direction and northward shifts in the along-track direction in general. More than half (42/54) of the time periods showed relative uncertainty larger than 5%, with the maximum even reaching 55.7%. Hence, the uncertainty caused by geolocation mismatch should be fully considered in the validation of satellite SIF products, especially over heterogeneous surfaces.

Cyberaggression is an important problem today; it can affect adolescents in different ways. Therefore, reliable and valid measures are necessary to better study the phenomenon. The aim of the present study was to generate validity and reliability evidence for a Spanish-language cyberaggression scale in a population of adolescents from northwestern Mexico. The results of this study contribute to the research and focus on cyberaggression in adolescents in Mexico. The measure in this article differs from other measures by detecting the different roles, including the bystander, contributing to the state of knowledge about cyberaggression, ratifying the presence of this actor that has not been sufficiently explored in the cyber context.

Background: Assessing body image and personalized rehabilitation in lower limb amputation is essential to measure impact on an individual’s quality of life and psychosocial wellbeing. The aim of this study was to develop a Spanish version of the Amputee Body Image Scale (ABIS-E) for Spanish-speaking lower limb amputee. Methods: A cross-sectional study was conducted including amputee patients in local in Madrid, Spain. Clinical outcomes about body image (Amputee Body Image Scale, ABIS), health-related quality of life (EuroQol-5D-5L), depression and anxiety (Hospital Anxiety and Depression Scale, HADS), pain (Brief Pain Inventory-Short Form, BPI-SF) and functional capacity (Prosthesis Evaluation Questionnaire, PEQ) were collected. Results: Seventy-three participants were assessed. Excellent test-retest reliability (ICC=0.847) and good internal consistency (Cronbach's alpha=0.753) were obtained. Three factors were extracted in the factor analyses. Convergent validity with Pearson's and Spearman's correlation coefficients were calculated for the depression and anxiety questionnaires (HADS) (values between .57 and .67), functional capacity (PEQ) (values between -.35 and .71) and quality of life (EQ-5D-5L) (values between -.37 and .61). Conclusions: The ABIS-E is a reliable and valid tool for measuring body image in the Spanish population with a lower limb amputation, potentially useful in primary care to identify psychosocial problems.

Eustachian Tube Dysfunction is considered a common condition among ENT patients and requires careful history, clinical examination and appropriate investigations to obtain a diagnosis. The ETDQ-7 questionnaire is a useful tool to subjectively score severity of symptoms that are related to this pathology (Appendix A). This study aimed to adapt and validate the ETDQ-7 questionnaire in Greece to ensure correct and efficient use in the outpatient setting (Appendix B). The ETDQ-7 was translated into the Greek language following appropriate methodology. Data for the main study were collected from a sample of 75 Greek patients diagnosed with ETD as well as 25 patients that did not have ETD and who served as a control group. The participants completed the adapted ETDQ-7 questionnaire and underwent a clinical examination that was statistically correlated with their ETDQ-7 answers. Face and content validity were confirmed and the questionnaire was found easy to administer and to be completed by our patients. Test-retest reliability revealed similar internal consistency for the questions and good correlation between individual items and total score. Discriminative validity confirmed statistically significant difference between the two patient groups to ensure that the Greek version of ETDQ-7 is useful to confirm the diagnosis. The Greek version of the ETDQ-7 is safe and efficient to use among a variety of investigation methods for the diagnosis of ETD in the Greek speaking population.

While there are several ways to identify customer behaviors, few extract this value from information already in a database, much less extract relevant characteristics. This paper presents the development of a prototype using the recency, frequency, and monetary attributes for customer segmentation of a retail database. For this purpose, the standard K-means, K-medoids, and MiniBatch K-means were evaluated. The standard K-means clustering algorithm was more appropriate for data clustering than other algorithms as it remained stable until solutions with 6 clusters. The evaluation of the clusters’ quality was obtained through the internal validation indexes: Silhouette, Calinski Harabasz, and Davies Bouldin. Once consensus was not obtained, three external validation indexes were applied: global stability, stability per cluster, and segment-level stability across solutions. Six customer segments were obtained, identified by their unique behavior: Lost customers, disinterested customers, recent customers, less recent customers, loyal customers, and best customers. Their behavior was evidenced and analyzed, indicating trends and preferences.

Background: The adoption of self-care behaviors among patients with arterial hypertension (AH) plays an important role in the management of their health condition. However, a lack of scales assessing self-care is observed. We aimed to develop and validate the Hippocratic hypertension self-care scale. Methods: From a pool of questions derived from a literature review, 18 items were included in the scale and reviewed by a committee of experts. Participants indicate the frequency at which they follow the self-behavior prescribed in each statement on a five-point Likert scale. Data were collected between April 2019 and December 2019. Re-sults: 202 consecutive adult patients with AH were enrolled in the study. The internal consistency of the scale was found to be 0.807, using Cronbach’s alpha coefficient. An exploratory factor analysis identified two do-mains that accounted for 92.94% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test- retest of the scale showed a significant strong correlation (r=0.0095, p<0.001). Conclusion: Our data indicate that the scale is a reliable and valid tool for assessing self-behaviors in patients with AH. Health professionals can use it in their clinical practice to improve the management of patients’ health condition.

Dietary fiber has been associated with health benefits, therefore, the availability of validated tools to assess food consumption associated with high-fiber foods would allow the quantification of the intake of this functional nutrient, the identification of risk groups and target populations, and the development of public policies and/or programs aimed at improving the health of the population. In this study, a fiber intake short food frequency questionnaire (FFQ) was translated into Spanish and its content validity was determined by a group of experts, to subsequently conduct a pilot test including 198 subjects aged 36+12.5 years, residing in Chile (46 men and 150 women), with the purpose of quantifying dietary fiber intake. The global assessment of the FFQ revealed a validity coefficient of 0.98+0.02; after the application of the pilot, mean dietary fiber intake in adult Chilean residents was of 13 g per day, with similar results to those found in the National Food Consumption Survey 2010 (12.5 g per day in men, and 11.5 g in women). The FFQ is a quick and valid tool to classify people on the basis of their habitual dietary fiber intake.

The spectrophotometric methods of determination of the active pharmaceutical ingredients meloxicam and nimesulide were reviewed, and a simple UV-spectrophotometric method for the determination of these active pharmaceutical ingredients in industrial equipment cleaning validation samples were proposed. The methods are based on extraction of the residual quantities of meloxicam and numesulide from the manufacturing equipment surface by the concentrated sodium carbonate solution, and the subsequent UV-spectrophotometric determination of the basic forms of the drugs at the wavelength of 362 nm for meloxicam and at 397 nm for nimesulide. The calibration graphs are linear in the range from 5 to 25 mg/L of both nimesulide and meloxicam, the molar attenuation coefficients are 6100 m2/mol for nimesulide and 9100 m2/mol for meloxicam, the limit of detection is 0.8 mg/L for nimesulide and 1.9 mg/L for meloxicam, the limit of quantification is 2.5 mg/L for nimesulide and 5.8 mg/L for meloxicam, the methods are selective with respect to the common excipients, show a good accuracy (the relative uncertainty does not exceed 4%) and precision (the relative standard deviation does not exceed 5%), do not require lengthy sample preparation and sophisticated laboratory equipment and are suitable for the routine analysis of cleaning validation samples.

Global crop yields are estimated to be reduced by 30–40% per year on account of plant pests and pathogens. Agricultural insect pests raise concerns about constraining global food security and climate changes contributing to the rise of infestation. The current management relies on plant breeding, associated or not with transgenes and chemical pesticides. Both approaches face serious technology obsolescence on the field due to resistance breakdown or development of insecticide resistance. The need for new Modes of Action (MoA) approaches in managing crop health grows each year, driven by market demands to reduce economic losses and phytosanitary requirements to meet the consumer perception. Disabling pest genes by sequence-specific expression silencing is considered a promising tool in the development of environment and health respectful biopesticides. The specificity conferred by long dsRNA-base solutions give support to minimizing effects on off-targeted genes in the insect pest genome and the target gene in non-target organisms (NTOs). In this review, we summarize the current status of gene silencing by RNA interference (RNAi) for agricultural control. More specifically, we focus on the engineering, development and application of gene silencing to control Lepidoptera by the employment of non-transforming dsRNA technologies. Despite some delivery and stability drawbacks of topical applications, we reviewed works showing convincing proof-of-concept results that point to imminent innovative solutions. Considerations about the regulamentation of the ongoing research on dsRNA-based pesticides to produce commercialized products for exogenous application are discussed. Academic and industry initiatives reveal a worthy effort to accomplish controlling Lepidoptera pests with this new mode of action to provide more sustainable and reliable technologies to field management. New data on genomics of this taxon encourage the increment of a customized target genes portfolio. As a case of study, we illustrate how dsRNA and associated methodologies could be applied to control an important Lepidopteran coffee pest.

Scientific literature shows increased interest in the aged and the aging phenomenon. The Aging Attitudes Questionnaire - AAQ was validated for the Portuguese population to understand the importance of attitudes towards old age and their impact on the subjective well-being of the elderly. A sample of 400 subjects (from 18 to 93 years) answered a socio-demographic questionnaire, and the AAQ was composed of three subscales (psychosocial losses, physical change, and psychological growth). The CFA confirmed the tri-factorial structure with very good adjustment of the model to the data with the Cronbach alpha of the total scale scoring .84 and ranging from .65 to .77 for each factor. A total of 9 items were omitted both for poor factor loadings (<0.50. Notwithstanding, 3 items below the criteria were maintained, as they conceptually fit into the factor. Of the final 15 AAQp items, 5 belong to the Psychosocial Loss factor, 6 to Physical Change, and 4 to Psychosocial Growth. This tree factor model explained 50.1 % of the total variance. In conclusion, this study supports that AAQ has acceptable validity, confirming the composite reliability and the discriminant validity, but not the convergent validity. Through multi-group analysis, the invariance of the scale was confirmed. This validation is of pivotal importance once it allows measuring the attitudes towards aging, thus facilitating the promotion of wellbeing across the lifespan.

The aim of this study, for determination of verteporfin in real samples (simulated body fluid, and simulated tears, 0.9% isotonic sodium chloride solution, Lactated Ringer IV solution for infusion, 5% dextrose IV solution for infusion, lemon juice and drinking water) was the method validation and to examined by HPLC-DAD-UV. Metod validation parameters such as specificity, linearity, precision, accuracy, robustness, limit of detection (LOD) and limit of quantitation (LOQ) for verteporfin were validated and developed according to the International Conference on Harmonization (ICH) Q2 R1 guidelines. The LOD and LOQ for verteporfin were found 0.06 µg/L and 0.2 µg/L, respectively. The recovery values of the optimization and validation for verteporfin were found in the range of 97.5-100.7%. The relative standard deviations (RSD) for vertepofin were <1%. The developed method was successfully applied to real samples with high accuracy and the recoveries (%) from real samples were 99.9, 100, 98.2, 99.2, 99.4, 98.8 and 99.4, respectively.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Gait analysis has historically been implemented in laboratory settings with expensive instruments; however, recently, wearable sensors have allowed the integration into clinical applications and use in daily activities. Previous studies have shown poor validity of ankle joints using inertial measurement units (IMUs), especially for small movement ranges. The purpose of this study was to validate the ability of commercially available IMUs to accurately measure the ankle joint angles during running. Ten healthy subjects participated in the study. Validation was performed by comparing the ankle joint angles measured using the wearable device with those obtained using the gold standard motion capture system during running. Reliability was evaluated using the intraclass correlation coefficient and standard error of measurement, whereas validity was evaluated using Pearson coefficient correlation method. Day-to-day reliability was excellent in the two planes for ankle joints. Validity was good in both sagittal and frontal planes for ankle joints. The results suggested that the developed device might be used as an alternative tool to the 3D motion capture system.

Background: Telemedicine is both effective and can provide efficient care at lower costs. It also enjoys a high acceptance rate among users. The Technology Acceptance Model proposed is based on the two main concepts of ease of use and perceived usefulness and comprises three dimensions: the individual context, the technological context and the implementation or organizational context. There is not a short and validated questionnaire to check the acceptance of telemedicine services amongst health care professionals using a technology acceptance model. Objective To translate and validate a telemedicine acceptance questionnaire based in the technology acceptance model. Methods The study included the following phases: adaptation and translation of the questionnaire into Catalan and psychometric validation which include construct (exploratory factor analysis), consistency (Cronbach’s alpha) and stability (test-retest). Factor analysis was used to describe variability amongst observed variables. Results After removing incomplete responses 144 responses where considered for analysis. The internal consistency measured with the Cronbach’s alpha coefficient was good with an alpha coefficient of 0.84 (95%, CI: 0.79-0.84). The intraclass correlation coefficient was 0.93 (95% CI: 0.852-0.964). The Kaiser-Meyer-Olkin test of sampling was adequate (KMO = 0.818) and the Bartlett test of sphericity was significant (Chi-square 424.188; gl=28; P < .001), indicating that the items were appropriate for a factor analysis. Conclusions The questionnaire validated with this study has robust statistical features that make it a good predictive model of professional’s satisfaction with telemedicine programs.

In the power plant industry, the turbine inlet temperature (TIT) plays a key role in the efficiency of the gas turbine and, therefore, the overall—in most cases combined—thermal power cycle efficiency. Gas turbine efficiency increases by increasing TIT. However, an increase of TIT would increase the turbine component temperature which can be critical (e.g., hot gas attack). Thermal barrier coatings (TBCs)—porous media coatings—can avoid this case and protect the surface of the turbine blade. This combination of TBC and film cooling produces a better cooling performance than conventional cooling processes. The effective thermal conductivity of this composite is highly important in design and other thermal/structural assessments. In this article, the effective thermal conductivity of a simplified model of TBC is evaluated. This work details a numerical study on the steady-state thermal response of two-phase porous media in two dimensions using personal finite element analysis (FEA) code. Specifically, the system response quantity (SRQ) under investigation is the dimensionless effective thermal conductivity of the domain. A thermally conductive matrix domain is modeled with a thermally conductive circular pore arranged in a uniform packing configuration. Both the pore size and the pore thermal conductivity are varied over a range of values to investigate the relative effects on the SRQ. In this investigation, an emphasis is placed on using code and solution verification techniques to evaluate the obtained results. The method of manufactured solutions (MMS) was used to perform code verification for the study, showing the FEA code to be second-order accurate. Solution verification was performed using the grid convergence index (GCI) approach with the global deviation uncertainty estimator on a series of five systematically refined meshes for each porosity and thermal conductivity model configuration. A comparison of the SRQs across all domain configurations is made, including uncertainty derived through the GCI analysis.

Background: Healthcare attention is sometimes considered purely technical, but communication has proven to be closely related to clinical results and patient satisfaction. Therefore, evaluation of communication in the scope of healthcare is a priority. The purpose of this study was to validate and adapt, if necessary, the Spanish version of the Communication Styles Inventory (CSI) in a sample of nursing professionals. (2) Methods: The sample was made up of 2313 nursing professionals selected at random from various medical centers in Spain, and is therefore a sample actively employed at the time data were acquired. We started out from the Communication Style Inventory, a questionnaire for evaluating the predominance of certain individual communication behaviors on six scales (expressiveness, preciseness, verbal aggressiveness, questioningness, emotionality and impression manipulativeness). (3) Results: Confirmatory Factor Analysis of the model proposed showed god fit indices. The reliability of the model shown by the Cronbach’s alpha of α=.81 was adequate, and so was single-level and aggregate consistency. Finally, in the analysis of variance by type of contract, configural, metric and scalar invariance was acceptable, but not strict invariance. (4) Conclusions: This instrument progresses in measuring non-technical attributes, such as communication styles, in nursing personnel.

Timely processing of observations from hyper-spectral imagers, such as SEVIRI (Spinning Enhanced Visible and Infrared Imager), largely depends on fast radiative transfer calculations. This paper mostly concerns the development and implementation of a new forward model for SEVIRI to be applied to real time processing of infrared radiances for the physical retrieval of surface temperature and emissivity. The new radiative transfer model improves computational time by a factor of ≈ 7 compared to the previous versions and makes it possible to process SEVIRI data at nearly real time. The new forward model has been applied for the simultaneous retrieval of surface temperature and emissivity in three infrared channels (8.7, 10.8, 12 μm). The inverse scheme relies on a Kalman filter approach, which allows us to exploit a sequential processing of SEVIRI observations. Based on the new forward model, the paper also presents a validation retrieval performed with in situ observations acquired during a field experiment carried out in 2017 at Gobabeb (Namib desert) validation station. Furthermore, a comparison with IASI (Infrared Atmospheric Sounder Interferometer) emissivity retrievals has been performed as well. It has been found that the retrieved emissivities are in good agreement with each other and with in situ observations, i.e. average differences are generally well below 0.01.

The creation of computer models is often driven by the need to make predictions in regions where there is no data (i.e. extrapolations). This makes validation challenging as it is difficult to ensure that a model will be suitable when it is applied in a region where there are no observations of the system of interest. The current paper proposes a method that can reveal flaws in a model which may be difficult to identify using traditional approaches for model calibration and validation. The method specifically targets the situation where one is attempting to model a dynamical system that is believed to possess time-invariant calibration parameters. The proposed approach allows these parameters to vary with time, even though it is believed that they are time-invariant. The of such an analysis is to identify key discrepancies - indications that a model has inherent flaws and, as a result, should not be used to influence decisions in regions where there is no data. The proposed method isn't necessarily a predictor of extrapolation performance, rather, it is a stringent test that, the authors believe, should be applied before extrapolation is attempted. The approach could therefore form a useful part of wider validation frameworks in the future.

Optoelectronic devices are gold standard for 3D evaluation in clinics but due to the complexity of such kind of hardware and the lack of access for patients affordable, transportable and easy to use systems must be developed to be largely used in daily clinics. The Kinect^TM sensor presents various advantages compared to optoelectronic devices: price, transportability but also some limitations: (in)accuracy of the skeleton detection and tracking as well as the limited amount of available points that make 3D evaluation impossible. To overcome these limitations a novel method has been developed to perform 3D evaluation of the upper limbs. This system is coupled to rehabilitation exercises allowing functional evaluation while performing physical rehabilitation. To validate this new approach a double step method was used. The first step is a laboratory validation where the results obtained with the Kinect^TM have been compared with results obtained with an optoelectronic device, 40 healthy young adults participated in this first part. The second step was to determine the clinical relevance of such kind of measurement. Results of the healthy subjects were compared with a group of 22 elderly adults and a group of 10 chronic stroke patients to determine if different patterns can be observed. The new methodology and the different steps of the validations are presented in this paper.

A specific HPLC method has been developed and validated for the determination of vanillyl butyl ether in cosmetic products. The extraction procedure with an isopropanol water 1:1 mixture is described. The method uses a RP-C-18 column with isocratic elution and a UV detector. The mobile phase consists of a mixture of acetonitrile and buffer (Na2HPO4 20mM in water) (30:70 v/v) with a variable flow rate. The method was validated with respect to accuracy, precision (repeatability and reproducibility), specificity and linearity. The procedure described here is simple, selective and reliable for routine quality control analysis and stability tests of commercially available cosmetic products.

In view of the expected climate changes, a paradigm shift in soil management, through reduced tillage and/or a different use of crop residues, can be a key point in the mitigation of the climate impacts. The transition from a traditional cropping system (i.e., durum wheat in continuous cropping system under conventional tillage and/or straw removal) to those undergoing the conservative practices require to be evaluated in a medium to long time frame to reach an equilibrium and thus to be properly investigated. In this regard, cropping system simulation models are fundamental tools for the in-silico evaluation of the response of crop growth and soil organic matter dynamics to varying cropping scenarios. This paper reports the evaluations on the parameterization and reliability of the ARMOSA crop simulation model calibrated and validated on experimental datasets collected on durum wheat grown in continuous cropping system under several straw and soil management strategies in a Mediterranean environment.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.

For the first time VIS/NIR-SWIR (visible and near infrared – shortwave infrared) nighttime spectra of a satellite mission are analyzed, using the EnMAP (Environmental Mapping and Analysis Program) high-resolution imaging spectrometer. The focus of this article is set on the spectral characteristics. First, the spectral calibration of EnMAP is checked based on sodium emissions of lighting. Here, applying a realized novel general method, shifts of +0.3nm for VIS/NIR and −0.2nm for SWIR are identified with uncertainties analyzed to be in the range of [−0.4nm,+0.2nm] for VIS/NIR and [−1.2nm,+1.0nm] for SWIR. These results emphasize the high accuracy of the spectral calibration of EnMAP and illustrate the feasibility of methods based on nighttime Earth observations for the spectral calibration of future nighttime satellite missions. Second, applying a realized simple general method, the dominant lighting types of Las Vegas, Nevada, USA, and thermal emissions are identified per pixel and the consistency of the outcomes is considered. These results illustrate the feasibility of the precise identification of lighting types and thermal emissions based on nighttime high-resolution imaging spectroscopy satellite products and support the specification of, in particular, spectral characteristics of future nighttime missions.

This paper is a response to the EPR paper titled: "Can quantum-mechanical description of physical reality be considered complete?", published in Physical Review in 1935. A quantum-mechanical (QM) measurement function describes a distribution of local results, while each empirical measurement process produces one result as exact as allowed by a measuring instrument calibrated to a non-local unit standard. Repeating these empirical measurements produces a Gaussian distribution of measurement results. The QM and empirical measurement result distributions can be compared. To precisely compare a QM measurement function describing a distribution of eigenvectors to a distribution of repetitive empirical measurement results, it is necessary to determine, by calibration, the precision of the eigenvectors to the same standard as the empirical results, because each eigenvector evidences uncertainty relative to a standard. When the calibration process is recognized as formal as well as empirical, QM measurement function results and metrology measurement process results are unified.

The on-state voltage of MOSFETs is a convenient and powerful temperature-sensitive electric parameter (TSEP) to determine the junction temperature, thus enabling device monitoring, protection, diagnostics and prognostics. The main hurdle in the use of the on-state voltage as a TSEP is the per-device characterization procedure, to be carried out in a controlled environment, with high costs. In this paper we compare two novel techniques for MOSFET junction temperature estimation: controlled shoot-through and direct heating by resistive heaters embedded in two Kapton (polyimide) films. Both allow in-place characterization of the TSEP curve with the device mounted in its final circuit and assembly, including the working heat sink. The two methods are also validated against the conventional procedure in a thermal chamber.

Heparins, Unfractionated or Low Molecular Weight, are permanently at the spotlight of both clinical indications and laboratory monitoring. An accurate drug dosage is necessary for an effi-cient and safe therapy. The one-stage anti-FXa kinetics’ assays are the most widely and universally used with full automation for large series, without needing exogenous Antithrombin. WHO in-ternational standards are available for UFH and LMWH, but external quality assessment surveys still report a high inter-assay variability. This heterogeneity results from: assay formulation, designed without or with dextran sulfate to measure all heparin in blood circulation; calibrators for testing UFH or LMWH with the same curve; and automation parameters. The various factors which impact heparin measurements are reviewed, and we share our experience to optimize assays for completely testing plasma heparin. Evidence is provided on the usefulness of low molecular weight dextran sulfate to mobilize all drug present in blood circulation. Other key factors concern adjustment of assay conditions to obtain fully superimposable calibration curves for UFH and LMWH, and automation parameters. The study is illustrated by the performances of the various anti-FXa assays used for testing heparin on UFH or LMWH treated patients’ plasmas and obtained using citrate or CTAD anticoagulants. Comparable results are obtained only when CTAD anti-coagulant is used. Using citrate UFH is underestimated in the absence of dextran sulfate. Heparin calibrators, adjustment of automation parameters and data treatment contribute to other smaller differences.