This paper presents an optimal design for the inner current control loop of the continuous current conduction mode (CCM) power factor correction (PFC) stage, which it can be used as the front stage of the two stages alternating current-direct current (AC-DC) telecom power supply. Conventional single-phase CCM-PFC boost converter usually implemented with using of the proportional-integral (PI) controllers in both of the voltage and current control loops, to regulate the output DC voltage to the specified value, moreover to maintains the input current follows the input voltage which offers converter with high power factor (P.F) and low current total harmonic distortion (THD). However, due to the slow dynamic response of the PI controller at the zero-crossing point of the input supply current, input current can’t fully follow the input voltage which leads to high THD. Digitally controlled PFC converter with an optimal design of the inner current control loop using doubly control loops IP controller to reduce the THD and to offer input current with unity P.F was performed in this paper. Furthermore, for the economic design of the digitally control PFC converter, two isolated AC and DC voltage sensors are proposed and designed for the interfacing with the microcontroller unit (MCU). PSIM software was used to test the converter performance with using the proposed designed current controllers and isolated voltage sensors. High power density digitally controlled telecom PFC stage with P.F of about 99.93%, full load efficiency of about 98.70% and THD less 5.50% is achieved in this work.

FoxP3 is a transcription factor essential for the differentiation and function of T regulatory cells (Tregs). There are two major subsets of Tregs: natural Tregs (nTregs) generated in thymus and inducible Tregs (iTregs) produced in peripheral immune system. It has been documented that iTreg development is dependent on soluble mediators including interleukin 2 (IL2), transforming growth factor β (TGFβ) and all-trans-retinoic acid (ATRA). In our experiments we performed a gene expression array, followed by Real-time PCR experiments, to study the expression of genes regulated by 1,25-dihydroxyvitamin D (1,25D) or ATRA in cells of myeloid origin. Our experiments revealed that ATRA alone, but also a cocktail of mediators consisting of IL2, TGFβ and ATRA, upregulate the expression of FOXP3 gene in lymphoid cells, but also in normal and leukemic myeloid cells. The FoxP3 expression is followed by a phenotypic changes in cells of myeloid origin. Our results indicate that signaling pathways which are used in the late stages of T cell differentiation, are also active in the cells of myeloid lineage

Measurement-Device-Independent Quantum Key Distribution (MDI-QKD) is a two-photon protocol devised to eliminate eavesdropping attacks that interrogate or control the detector in realized quantum key distribution systems. In MDI-QKD, the measurements are carried out by an untrusted third party, and the measurement results are announced openly. Knowledge or control of the measurement results gives the third party no information about the secret key. Error-free implementation of the MDI-QKD protocol requires the crypto-communicating parties, Alice and Bob, to independently prepare and transmit single photons that are physically indistinguishable, with the possible exception of their polarization states. In this paper, we apply the formalism of quantum optics and Monte Carlo simulations to quantify the impact of small errors in wavelength, bandwidth, polarization and timing between Alice's photons and Bob's photons on the MDI-QKD quantum bit error rate (QBER). Using published single-photon source characteristics from two-photon interference experiments as a test case, our simulations predict that the finite tolerances of these sources contribute (4.04+/-20/N_sifted) to the QBER in an MDI-QKD implementation generating an N_sifted-bit sifted key.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

We recently reported that in the spinal cord of PPMS or SPMS patients, large areas of periplaque demyelinating lesions extend distance away from plaque borders. Such lesions are characterized by a progliotic TGF-beta 1 signature accompanied by: i) a low-grade inflammatory reaction, ii) an extensive astrocytosis and iii) a process of incomplete demyelination. It was proposed that, while efficiently dampening inflammation in MS spinal cords, TGF-beta 1 could promote astrocytosis, prevent remyelination and possibly trigger alterations of myelin synthesis. In light of these findings, a re-interpretation of two large neuropathological studies performed on MS brains and spinal cords is provided here. While results from these studies clearly showed that active plaques do not display any region-specific distribution, an important point was apparently overlooked and not discussed by the authors: a significantly higher percentage of inactive plaques was found in MS spinal cords as compared to brains and, conversely, the percentage of slowly-expanding (or smoldering) lesions was significantly lower in the spinal cord as compared to the brain. These data indicate that the spinal cord environment may be more favorable to the resolution of inflammation. Downstream of the autoimmune process leading to plaque formation, region-specific mechanisms may thus drive the outcome of active plaques. While inflammation triggers tissue destruction, inflammation may also be needed for effective tissue repair and an inappropriate dampening of inflammatory events may possibly translate into a poor level of remyelination in MS spinal cords. It is proposed here that TGF-beta 1 is involved in such a brain-spinal cord dissociation of active plaques outcome.

Breast cancer (BC) is the most common malignancy and second only to lung cancer in terms of mortality in women. Despite the incredible progress made in this field, the metastatic breast cancer leaves a poor prognosis. In an era of personalized medicine, there is an urgent need for a better knowledge of the biology leading to the disease, which can lead to the design of always more accurate drugs against patients’ specific molecular aberrations. Among one of the actionable targets is the Fibroblast Growth Factor Receptor (FGFR) pathway, triggered by specific ligands. The FGFRs/FGFs axis offers interesting molecular targets to be pursued in clinical development. This mini-review will focus on the current knowledge of the FGFRs mutations leading to tumour formation and summarizes the state-of-the-art of therapeutic strategies for targeted treatments against the FGFRs/FGFs axis in the context of BC.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

A new series of 1,3,4-oxadiazoles derivatives was synthesized, characterized and evaluated for their in vitro and in vivo anti-thrombotic activity. Compounds (3a-3i) exhibited significant clot lysis with respect to negative control and reference drug streptokinase (30,000 IU) while enhanced clotting time (CT) values were observed (130-342 sec) for these tested compounds than the standard drug heparin (110 sec.). High affinity towards 1NFY with greater docking score was observed for the compounds (3a, 3i, 3e, 3d and 3h) than the control ligand RPR200095. In addition, very good inhibitory potential against factor Xa (F-Xa) was observed with higher docking scores (5612-6270) with ACE values (–189.68 to –352.28 kcal/mol) than the control ligand RPR200095 (Docking score 5192; ACE –197.81 kcal/mol. In vitro, in vivo and in silico results proposed that these newly synthesized compounds can be used as anti-coagulant agents.

Background and objectives: Contrast-induced nephropathy (CIN), is an acute renal damage due to contrast agents. This study is conducted to determine the potential diagnostic value of hypoxia-inducible factor 2-alpha (HIF2-α) and to evaluate the renal protective effects of N-acetyl cysteine (NAC) and sildenafil in a rat CIN model. Material/Methods: This randomized, controlled, interventional animal study was conducted on Wistar rats. Totally, rats (n = 36) were randomly assigned to four groups: control (n = 9), CIN group (n = 9), CIN+NAC group (n = 9), and sildenafil (n = 9). The rat model was used to form iohexol-originated CIN. During the modelling, prophylactic treatment was performed at 24th and 48th hours. After 48 hours of the modelling; blood, urine, tissue samples were obtained for biochemical analyses. HIF-2-α levels were measured in renal tissue, serum and urine samples. Renal sections were performed in order for histopathologic and immunohistochemical evaluations. Results: In the CIN model, HIF-2α levels and other biochemical parameters were significantly increased (p < 0.01). Both sildenafil and NAC, efficiently decreased the renal damage due to contrast agents (p < 0.05). Similarly, after treatment with sildenafil and NAC, HIF-2α levels were significantly decreased (p < 0.05). Conclusions: The current study constructs an experimental base for the use of HIF-2α for clinical prevention and treatment of CIN. Several mechanisms may be postulated for the changes in HIF-2α levels. Besides, the increased HIF-2α levels with CIN and decreased HIF-2α levels after treatment may be used for the treatment and follow-up of patients with CIN.

Mereology stands for the philosophical concept of parthood and is based on a sound set of fundamental axioms and relations. One of these axioms relates to the existence of a universe as a thing having part all other things. The present article formulates this logical expression first as an algebraic inequality and eventually as an algebraic equation reading in words: The universe equals the sum of all things. “All things” here are quantified by a “number of things”. Eventually this algebraic equation is normalized leading to an expression The whole equals the sum of all fractions. This introduces “1” or “100%” as a quantitative – numerical - value describing the “whole”. The resulting “basic equation” can then be subjected to a number of algebraic operations. Especially squaring this equation leads to correlation terms between the things implying that the whole is more than just the sum of its parts. Multiplying the basic equation (or its square) by a scalar allows for the derivation of physics equations like the entropy equation, the ideal gas equation, an equation for the Lorentz-Factor, conservation laws for mass and energy, the energy-mass equivalence, the Boltzmann statistics, and the energy levels in a Hydrogen atom. It further allows deriving a “contrast equation” which may form the basis for the definition of a length and a time scale. Multiplying the basic equation with vectors, pseudovectors, pseudoscalars and eventually hypercomplex numbers opens up the realm of possibilities to generate many further equations.

Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

The cellular stress response corresponds to the molecular changes that cell undergoes in response to various environmental stimuli. It induces drastic changes in the regulation of gene expression, at transcriptional and post-transcriptional levels. Actually, translation is strongly affected with a blockade of the classical cap-dependent mechanism, whereas alternative mechanisms are activated to support translation of specific mRNAs. One of the major mechanisms involved in stress-activated translation is the internal ribosome entry site (IRES)-driven initiation. IRESs, first discovered in viral mRNAs, are present in cellular mRNAs coding for master regulators of cell responses, whose expression must be tightly controlled. IRESs allow translation of these mRNAs in response to different stresses, including DNA damage, amino-acid starvation, hypoxia or endoplasmic reticulum stress, as well as to physiological stimuli such as cell differentiation or synapse network formation. Importantly, cellular mRNA IRESs are regulated by IRES trans-acting factor (ITAFs), exerting their action by at least nine different mechanisms. This review presents an update of the reported ITAFs regulating cellular mRNA translation and of the different mechanisms allowing them to control translation initiation in specific conditions. The impact of ITAFs on coordinated expression of mRNA families and consequences in cell physiology and diseases are also highlighted.

The RAINBOW Phase III study established the efficacy of the combination of paclitaxel and ramucirumab, a monoclonal antibody targeting VEGF receptor-2 (VEGF-R2), as second-line therapy. We retrospectively analyzed the data of patients treated with ramucirumab plus paclitaxel at our Institution to evaluate the impact of clinical heterogeneous figures on the efficacy and safety of this combination paclitaxel/ramucirumab in a real- life cohort of patients. After a median follow-up of 10.74 months, the median progression-free survival (PFS) was 5.8 months (95% CI: 3.04 - 5,63). Disease control rate (DCR) was 61% and the median duration of response (DOR) was 5.8 months. Median overall survival (OS) was 8.3 months. A trend toward better outcome was observed in HER2 positive patients. In multivariate analysis, nutritional status (p = 0.0001) and number of metastatic sites (p = 0.0266) resulted significantly related with longer PFS. Our analysis confirmed the efficacy and safety of the combination of ramucirumab with paclitaxel also in the real-life practice and the median PFS is significantly longer than that reported for Western population in previous studies. Subgroup analysis confirms the key-role of nutritional status as prognostic factor and suggests a possible interaction between EGF and angiogenesis pathways that deserves further investigations.

Approximately 240 million people are chronically infected with hepatitis B virus (HBV), despite four decades of an effective HBV vaccine. During chronic infection, HBV forms two distinct templates responsible for viral gene transcription: (1) episomal covalently closed circular (ccc)DNA and (2) host-genome integrated viral templates. Multiple ubiquitous and liver-specific transcription factors are recruited onto these templates and modulate viral gene transcription. This review details the latest developments in antivirals that inhibit HBV gene transcription, and their impact on the stability of viral transcripts. Notably, nuclear receptor agonists exhibit potent inhibition of viral gene transcription from cccDNA, small molecule inhibitors repress HBV X protein-mediated transcription from cccDNA and small interfering RNAs and single-stranded oligonucleotides result in transcript degradation from both cccDNA and integrant templates. These antivirals mediate their effects by reducing viral transcripts abundance, eventually leading to loss of surface antigen expression, and can potentially be added to the arsenal of drugs with demonstrable anti-HBV activity. Thus, these candidates deserve special attention for future repurposing or further development as anti-HBV therapeutics.

The stability between the limited available energy resources and their consumption is an important concern of the modern world. The study deals with the development of the methods for measuring the energy performance of different renewable and non-renewable resources used for electricity generation with the help of an energy performance indicator called the Primary Energy Factor (PEF). This study takes account of all energy stages from the resources extraction to its transportation, conversion, combustion and then finally to utilization. The study conducted a comparative approach to calculate the PEF values of electricity generated in South Korea from the period of 1980 to 2017. Four different methodologies namely Eurostat methodology, Life cycle methodology, Modified Eurostat methodology, and upper-end methodology have been used. A set of Programs has been written in MATLAB to calculate the i. PEF values of electricity generated. ii. Impact of different renewable and non-renewable energy sources on PEF values. iii. Future trend of PEF values of electricity in South Korea At the national and local level, this study will help the government and other law-making institutions to make policies regarding annual purchase consumptions of energies by different industrial, residential, public and transportation sectors and at the Global level, the implementation of this study will be the catastrophe of maintaining the stability between the available energy resources, and consumptions. This, in turn, will lead to suitable living conditions for future generations

The research sought to investigate the long term characteristics of wind in the Kisii region (elevation 1710m above sea level, 0.68^oS, 34.79^o E). Wind speeds were analyzed and characterized on short term (per month for a year) and then simulated for long term (ten years) measured hourly series data of daily wind speeds at a height of 10m. The analysis included daily wind data which was grouped into discrete data and then calculated to represent; the mean wind speed, diurnal variations, daily variations as well as the monthly variations. The wind speed frequency distribution at the height 10 m was found to be 2.9ms^-1 with a standard deviation of 1.5. Based on the two month’s data that was extracted from the AcuRite 01024 Wireless Weather Stations with 5-in-1 Weather Sensor experiments set at three sites in the region, averages of wind speeds at hub heights of 10m and 13m were calculated and found to be 1.7m/s, 2.0m/s for Ikobe station, 2.4m/s, 2.8m/s for Kisii University stations, and 1.3m/s, 1.6m/s for Nyamecheo station respectively. Then extrapolation was done to determine average wind speeds at heights (20m, 30m, 50m, and 70m) which were found to be 85.55W/m², 181.75W/m², 470.4W/m² and 879.9W/m² respectively. The wind speed data was used statistically to model a Weibull probability density function and used to determine the power density for Kisii region.

The new coronavirus disease 2019 (COVID-19) pandemic is an emerging situation with high rates of morbidity and mortality, in the pathophysiology of which inflammation and thrombosis are implicated. The disease is directly connected to the nutritional status of patients and a well-balanced diet is recommended by official sources. Recently, the role of platelet activating factor (PAF) was suggested in the pathogenesis of COVID-19. In the present review several micronutrients (vitamin A, vitamin C, vitamin E, vitamin D, selenium, omega-3 fatty acids, minerals), phytonutrients and Mediterranean diet compounds (olive oil, fish, honey, plant foods) with potential anti-COVID activity are presented. We further underline that the well-known anti-inflammatory and anti-thrombotic actions of the investigated nutrients and/ or holistic dietary schemes, such as the Mediterranean diet, are also mediated through PAF. In conclusion, although there is no single food to prevent coronavirus, the aim is to follow a healthy diet containing PAF inhibitors in order to target both inflammation and thrombosis and try to avoid or/and reduce the deleterious effects of the COVID-19 epidemic.

The crack in the blade is the most common type of fatigue damage for Francis turbines. However, the crack sometimes is difficult to be detected in time using the current monitoring system even when the crack is very large. To better monitor the crack, it is imperative to research the effect of a crack on the dynamic behavior of a Francis turbine. In this paper, the dynamic behavior of a Francis turbine runner model with a crack was researched numerically. The intact numerical model was first validated by the experimental data available. Then, a crack was created at the intersection line between one blade and the crown. The change in dynamic behavior with increasing crack length was investigated. Crack-induced vibration localization theory was used to explain the dynamic behavior changes due to the crack. Modal analysis showed that the adopted theory could basically explain the modal behavior change due to the crack. The FFT results of the modal shapes and the localization factors (LF) were used to explain the forced response changes due to the crack. Based on the above analysis, the challenge of crack monitoring was analyzed. This research can also provide some references for more advanced monitoring technologies.

Due to the upward trend in the globalization of sustainability issues and the intense competitive environment, it is evident that higher education institutions need new strategic approaches to succeed. To this end, the inquiry for this paper has been made into the debate about student relationship management. Going through the literature indicates that institutions have mainly perceived the concept as a technological initiative for solving the problems in individual domains, accompanied by uncoordinated efforts. Thus, the aims of this study are to theoretically present critical success factors of this strategic approach and to empirically examine the recognized factors. To do so, confirmatory factor analysis that is a quantitative analytic method was performed. The results and analyses revealed that there has been a significant correlation between the four critical success factors including knowledge management, student relationship management technology, student orientation, and employees’ involvement. It was also found that these factors are significantly correlated with the construct of student relationship management success. The findings have consequently highlighted that in addition to the technological tool, the role of knowledge management, employees’ involvement, and student orientation appeared to be particularly important for the implementation of the application.

Following an initial mechanical insult, traumatic spinal cord injury (SCI) induces a secondary wave of injury, resulting in a toxic lesion environment inhibitory to axonal regeneration. This review focuses on the glial cell line-derived neurotrophic factor (GDNF) and its application, also in combination with other factors and cell transplantations, for repairing the injured spinal cord. As recent decades of studies strongly suggest combinational treatment approaches hold the greatest therapeutic potential for the central nervous system (CNS) trauma, future directions of combinational therapies will also be discussed.

In last decades, growing migration flows have modified the obstetric clinical care, requiring specific attention by health care systems. The aim was to describe the phenomenon focusing on miscarriage (pregnancy loss at <20 weeks). Patients admitted for care at miscarriage in a six-year period (2012-17) were revised. Miscarriage rates in all ethnic groups, dichotomized in early (within the first 12 weeks of gestation) and late (at <20 weeks) pregnancy loss. Associations between women's characteristics (age, parity, inter-pregnancy interval (IPI)) were explored to elucidate any differences. A total of 1,940 patients were included, segregated in early (n = 1769, 91.2%) and late (n = 171, 8.8%) pregnancy losses. Caucasian ethnicity was the most common (87.9%), leaving the minority groups to 12.1%. Maternal age was higher among Caucasians women than other subgroups, in contrast to Asiatic patients. Nulliparity was observed in 1045 (53.9%) patient, more widespread among Caucasian and Maghrebins. A positive obstetric history counting at least one miscarriage was frequent, ranging from 22.2% to 75%, in particular among Asiatic women, while the recurrence in Caucasians. In Afro-Carribeans the most relevant rate of late miscarriage was found. By multiple regression modelling, maternal age, nulliparity and Afro-Carribean were identified as determinants. Maternal ethnicity should be considered in the management of pregnancy losses in combination with already well-defined risk factors, including age at miscarriare and nulliparity.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

Severe acute respiratory syndrome coronavirus 2 (SARS-Cov-2), coronavirus disease 2019 (COVID-19)-induced infection is strongly associated with various coagulopathies that may result in either bleeding and thrombocytopenia or hypercoagulation and thrombosis. Thrombotic and bleeding or thrombotic pathologies are significant accompaniments to acute respiratory syndrome and lung complications in COVID-19. Thrombotic events and bleeding, often occurs in subjects with weak multiple risk factors and co-morbidities. Of particular interest are the various circulating inflammatory coagulation biomarkers involved directly in clotting, with specific focus on fibrin(ogen), D-dimer, P-selectin and von Willebrand Factor (vWF). Central to activity of these biomarkers are their receptors and signaling pathways on endothelial cells, platelets and erythrocytes. In this review, we discuss vascular implications of COVID-19, and relate this to circulating biomarker, endothelial, erythrocyte and platelet dysfunction. During the progression of the disease, these markers may either be within healthy levels, upregulated or eventually depleted. Most significant is that patients need to be treated early in the disease progression, when high levels of vWF, P-selectin and fibrinogen are present with still low levels of D-dimer. Progression to vWF and fibrinogen depletion with high D-dimer levels and even higher P-selectin levels, followed by the cytokine storm, will be indicative of a poor prognosis. We conclude by looking at point-of-care devises and methodologies in COVID-19 management and suggest that a personalized medicine approach should be considered in the treatment of patients.

The Rybczynski theorem describes the trade effect within production analyses between factor endowments and outputs. The Stolper-Samuelson theorem focuses on cost analyses between factor reward and commodity price. This paper examines the trade effect of changes of factor endowments on prices, based on general equilibrium. The study shows that changes of factor endowments cause domestic output changes (the Rybczynski effect), which affect output prices and factor prices (the Stolper-Samuelson effect). It is like a chain of effects that the Rybczynski’s trade effect triggers the Stolper-Samuelson’s trade effect. The analysis of this paper shows that a small increase of a factor endowment of any country rewards another factor and the commodity using the latter factor intensively. It displays a tuneful circle. Trade brings a well-balanced development to the world.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

As an emerging building solution, cross-laminated timber (CLT) floors have been increasingly used in mass timber construction. The current vibration design of CLT floors is conservative due to the assumption of simple support conditions in the floor-to-wall connections. It is noted that end fixity occurs as a result of clamping action at the ends, arising from the gravity load applied by the structure above the floor and by the mechanical fasteners. In this paper, the semi-rigid floor-to-wall connections are treated as elastically restrained edges against rotations to account for the effect of partial constraint. A rotational end-fixity factor was first defined to reflect the relative bending stiffness between CLT floors and elastic restraints at the edges. Then, for the design of vibration serviceability of CLT floors as per the Canadian Standard for Engineering Design in Wood (CSA O86), restraint coefficients were defined and their analytical expressions were derived for natural frequencies and the mid-span deflection under a concentrated load, respectively. In particular, a simplified formula of the restraint coefficient for the fundamental frequency was developed to assist engineers in practical design. At last, by comparing with reported experimental data, the proposed design formula showed excellent agreement with test results. In the end, the proposed end fixity factor with their corresponding restraint coefficients is recommended as an effective mechanics-based approach to account for the effect of end support conditions of CLT floors.

Colostrum is a natural product, issued by both mammals and humans in first week of lactation. Among different species, donkey colostrum is considered as having, besides a valuable composition in nutrients and immune factors, an outstanding similitude with human colostrum. In this context, and taking into account the scarcity of available data concerning the interaction between climate factors and colostrum quality, a trial was conducted aiming to identify the possible influence of environmental factors on donkey colostrum nutritional traits. A stock of 16 jennies from 2 farms located in the County of Cluj, during a 7 days postpartum period was analyzed. During experimental period the daily temperature, humidity, and wind velocity data were collected. Strong positive correlations may be reported between fat and lactose, and fat and protein respectively, while moderate to strong correlation is emphasized between lactose and protein content of donkey colostrum. Testing the influence of environmental temperature, relative humidity, and wind velocity influence upon nutritional content of donkey colostrum, results the neglectable influence of the wind velocity, the negative influence of the heat stress upon all studied colostrum components, and complex influence of relative humidity, which has positive influence on fat and lactose increase when it increases, while its increase has negative influence on protein content of donkey colostrum.

Precipitation gauges are critical for measuring precipitation rates at regional and global scales and are often used to calibrate precipitation rates estimated from other instruments such as satellites. However, precipitation measured at the gauges is affected by gauge-undercatch that is often larger for solid precipitation. In the present work, two popular gauge-undercatch correction factors are assessed: one utilizes a dynamic correction model and is used in the Global Precipitation Climatology Centre (GPCC) Monitoring product and the other one employs a fixed climatology and is used in the Global Precipitation Climatology Project (GPCP) product. How much the choice of correction factors can impact the total estimate of precipitation was quantified over land at seasonal, annual, regional, and global scales. The correction factors are also compared as a function of the environmental variables used in their development, among those are near-surface air temperature, relative humidity, wind speed, elevation, and precipitation intensity. Results show that correction factors can increase the annual precipitation rate based on the gauges by ~9.5 % over the global land (excluding Antarctica), although this amount can vary from ~6.3% (in boreal summer) to more than 10% (in boreal winter), depending on the season and the method used for gauge-undercatch correction. Annual variations of correction factors can also be large, so the use of the fixed climatology correction factors requires caution. Given their magnitudes and differences, selection of appropriate correction factors can have important implications in refining the water and energy budget calculations.

Cemented rock fill (CRF) is commonly used in cut-and-fill stoping operation in underground mining. This allows for the maximum recovery of ore. Backfilling can improve stope stability in underground workings, and then improve ground stability of the whole mine site. Backfilling step scenarios vary from site to site. This paper presents the investigation of five different backfilling step scenarios and their impacts on the stability of stopes at four different mining levels. A comprehensive comparison of displacements, major principal stress and stress concentration factor (SCF) was conducted. The results show that different backfilling step scenarios have little influence on the final displacement for displacement in the stopes. Among the five backfilling scenarios, the major principal stress and stress concentration factor (SCF) have almost the same final results. The backfilling scenario SCN-1 is the optimum option among these five backfilling scenarios. It can immediately prevent the increase of the displacement and reduce the sidewall stress concentration, thereby preventing possible failures. Using the same strength of CRF can achieve same effects among the four mining levels. Applying backfilling CRF of the same strength at different mining depths is acceptable and feasible to improve the stability of the stopes.

Phosphorus (P) is an important element in a complete and balanced fertility program that can improve crop P use efficiency and ultimately productivity and profitability. Phosphatic fertilizers use without organic fertilizers leads to gradual decline in soil organic matter, native nutrient status and ultimately reduction in agricultural productivity and economic growth. The objectives of this was to evaluate P efficiencies with incorporation of peach sources, beneficial microbes and P application. From sustainability points of view, alternative use of different sources and forms of organic sources alone or in combination with inorganic P and beneficial microbes possess potential for improving productive capacity of the soil. Separate field experiments (one each on maize and soybean as a test crop) were conducted at Agriculture Research Institute Mingora Swat (ARI) for two consecutive years in summer season of 2016 (year one) and 2017 (year two). For the first time such a study were conducted to utilize peach leftovers and biomass (leaves, twigs, fruits, stones and barks partially decomposed, its compost and biochar) along with three phosphorus (P) levels (50, 75, 100 kg P ha-1) and two beneficial microbes (PSB and Trichoderma) on such a way to enhance soil sustainability and P use efficiency of soybean and maize. The results revealed that organic sources had significant effect on soybean and maize P use efficiency (PUE), P agronomic efficiency (PAE), partial factor productivity (PFPp) and soil P concentration. In experiment 1 among the organic sources, peach residues increased soil P (12.0 mg kg-1) as compared to peach compost and biochar (8.6 & 11.7 mg kg-1). Soil P concentration was maximum (12.1 mg kg-1) with PSB than Trichoderma (9.5 mg kg-1). Application of P at 100 kg ha-1increased soil P contents (16.9 mg kg-1) as compared to 50 and 75 kg P ha 1 (5.9 & 9.6 mg kg-1) respectively. P concentration was increased drastically in year 2 (12.4 mg kg-1) than year one (9.1 mg kg-1). PUE in both crops (soybean and maize) was maximum (25.6 & 28.4%) with peach biochar than compost and residues along with Trichoderma (21.7 & 27.8%). Highest PUE in soybean was recorded with 75 kg P ha-1(22.2%) however in maize maximum PUE was noted with 50 kg P ha-1(33.5%). PAE and PFPp in both crops was maximum with biochar and soil application of Trichoderma than other organic sources and PSB. Among the P levels highest PAE in soybean and maize was recorded with 75 kg ha-1whereas PFPp in soybean was maximum with 75 kg P ha-1 and interestingly in maize it was noted with 50 kg ha-1. Conclusively soybean and maize PAE, PFPp and PUE was higher with biochar, soil incorporation of Trichoderma and P at the rate of 75 kg ha-1 and can improve soybean and maize yield and soil productivity on sustainable basis.

Background: Absolute uterine factor infertility (AUFI) is a kind of infertility that is completely attributable to uterine absence (surgical or congenital for women with Mayer-Rokitansky-Küster-Hauser syndrome: MRKH) or anatomic or functional abnormality that prevents embryo implantation or completion of pregnancy to term. Until recently, the only viable option to parenthood for couples with AUFI were adoption or surrogacy. Since a first attempt of uterus transplant (UTx) in 2000, nine babies were born from women with a transplanted uterus from 2014, eight of which in Sweden, and one in the United States. These promising results are raising immense hopes for the women with AUFI and there is optimism about the possibility for UTx to become part of clinical care even though, besides encouraging results, the procedure has also resulted in increased risks and harms for both the donors and recipients and increased risks of premature birth for the fetus. At present UTx is still considered as experimental and requiring more research and safety assessment before becoming a therapeutic option for AUFI. The transition from experimental procedure to therapeutic care would result in less strict ethical scrutiny for UTx and in the possibility for patients to get reimbursement for the procedure by the relevant healthcare insurance or public healthcare providers. In turn, an increase in the number of UTx performed yearly by specialized surgical teams would result in a general improvement of the “field strength”. However, at present it is difficult to establish the amount of evidence that we need in order to consider UTx as no longer experimental but routine clinical practice. The literature on UTx provides recommendations on the different outcomes that should be monitored in this experimental phase but no study is anticipating the number of subjects that should be followed and for how long. Conclusion: As for other transplants that have become routine practice, like renal transplant and heart transplant, it is likely that the decision on “routine practice readiness” will result from available cumulated evidences, from expert capacity to find a consensus on best practices and on political considerations as well, including pressures form patients and patient groups.

Understanding the biology underlying the mechanisms and pathways regulating pancreatic β-cell development is necessary to understand the pathology of diabetes mellitus (DM), which is characterized by the progressive reduction in insulin producing β-cell mass. Pluripotent stem cells (PSCs) can potentially offer an unlimited supply of functional β-cells for cellular therapy and disease modeling of DM. Homeobox protein NKX6.1 is a transcription factor (TF) that plays a critical role in pancreatic β-cell function and proliferation. In human pancreatic islet, NKX6.1 expression is exclusive toβ-cells and is undetectable in other islet cells. Several reports showed that activation of NKX6.1 in PSC-derived pancreatic progenitors (MPCs), expressing PDX1 (PDX1⁺/NKX6.1⁺), warrants their future commitment to monohormonal β-cells. However, further differentiation of MPCs lacking NKX6.1 expression (PDX1⁺/NKX6.1^-) results in an undesirable generation of non-functional polyhormonal β-cells. The importance of NKX6.1 as a crucial regulator in MPC specification into functional β-cells directs attentions to further investigating its mechanism and enhancing NKX6.1 expression as a mean to increase β-cell function and mass. Here, we shed light on the role of NKX6.1 during pancreatic β-cell development and in directing the MPCs to functional monohormonal lineage. Furthermore, we address the transcriptional mechanisms and targets of NKX6.1 as well as its association with diabetes.

The details of antigen-antibody interactions and the identification of epitopes are critical for the development of monoclonal antibody drugs. Ab42 is a native human-derived anti-CFH monoclonal antibody. In this study, the interaction between antigen pCFH and antibody (Ab42) was theoretically demonstrated by molecular docking and MD simulation, combined with free energy calculation and computational alanine scanning (CAS), and key amino acids and epitopes were identified. Experimental alanine scanning (EAS) was then carried out to verify the results of the calculation, and our results indicated that Ab42 antibody forms hydrogen bonds and interacts hydrophobically with pCFH through the Tyr315, Ser100, Gly33, and Tyr53 residues on its CDR, while the main pCFH epitopes are located at the six sites of Pro441, Ile442, Asp443, Asn444, Ile447, and Thr448. In conclusion, this study has explored the mechanism of antigen-antibody interaction from both theoretical and experimental aspects, and our results have important theoretical significance for the design and development of relevant antibody drugs.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

Genetic switches can be utilized for many purposes in synthetic biology including the assembly of complex genetic circuits to achieve sophisticated cellular systems and the construction of biosensors for real-time monitoring of intracellular metabolite concentrations. Although genetic switches have mainly been developed in prokaryotes to date, eukaryotic genetic switches are increasingly being reported as both rational and irrational engineering technologies mature. In this review, we describe genetic switches in yeast based on synthetic transcription factors and/or synthetic promoters. We also discuss directed evolution technologies for the rapid and robust construction of yeast genetic switches.

Three-phase to single-phase matrix converter (TSMC) is used as the transmitter for transient electromagnetic method (TEM) instrument, instead of an AC-DC converter and an H-bridge inverter. The transmitter produces excitation current for primary field. The output current has a waveform with a bipolar square of half duty cycle, which is required by TEM. The space vector PWM based on input currents is discussed in detail. The control method of input power factor is proposed for TSMC. The simulation model of TSMC is established and the simulations of different conditions are completed. The simulation results show the controllability of the input power factor is illustrated.

Motorcycles can be considered a new form of smart vehicle when taking into account their small and modern structure and due to the fact that nowadays they are used in the new role of ambu-lance to rapidly reach emergency patients in large cities with traffic congestion. However, there is no study regarding the measuring of access time for motorcycle ambulances in large cities of Thailand. Therefore, this study aims to compare access times to patients between motorcycle ambulances and conventional ambulances, including analysis of the use of AED installed on motorcycle ambulances to contribute to the sustainable development of public health policies. In two hundred and seventy-one operations, it was found that the times from dispatch to vehicle (ambulance and motorlance) being en route and times from the 1669 center (center for com-mand-and-control EMS in Thailand) call receipt to arrival on scene (response time) of motorcycle ambulances was shorter than that of a conventional ambulance and the use of AED on a motor-cycle ambulance can increase the chances of survival for patients with cardiac arrest outside the hospital in public places where AEDs are not available and in all cases where access to an AED was less than eight minutes.

The notion of enhancement of the image is to ameliorate the perceptibility of information contained in an image. In the present research, a novel technique for the enhancement of image quality is propounded using fuzzy logic technique with a cuckoo optimization algorithm. Generally, the image is transformed from RGB domain to HSV domain keeping the color information intact within the image. The image has been categorized into three regions: underexposed, overexposed and mixed region on the basis of two threshold values. For the fuzzification of under and overexposed area the degree of membership is defined by the Gaussian membership, while the mixed area is fuzzified by parametric sigmoid function. The key parameters like visual factors and fuzzy contrast provide the quantitative analysis of an image. An objective function is framed which involves entropy and visual factor has been optimized by a new evolutionary cuckoo optimization algorithm. The results procured after simulation by the cuckoo optimization algorithm are compared with Bacterial foraging algorithm and ant colony optimization based image enhancement and this approach is found to be improved.

Neuroinflammatory responses are implicated in the pathogenesis of neurodegenerative diseases. In neurodegenerative diseases, neuroinflammatory reactions to neuronal injury are modulated by microglial cells, which are vital innate immune cells in the central nervous system. Activated microglial cells release proinflammatory cytokines, mediators, and neurotoxic factors that induce fatal neuronal injury. The present study investigated the anti-neuroinflammatory effects of cudratricusxanthone L (1), which was isolated from Cudrania tricuspidata. This compound reduced the levels of lipopolysaccharide-stimulated inflammatory mediators and cytokines, including nitric oxide, prostaglandin E2, interleukin (IL)-1β, tumor necrosis factor-α, IL-6, and IL-12. These effects suggested that cudratricusxanthone L (1) suppressed the nuclear factor-kappa B (NF-κB) signaling pathway. Specifically, cudratricusxanthone L (1) also attenuated the phosphorylation of Jun kinase and inhibited p38 mitogen-activated protein kinase (MAPK) signaling in BV2 and rat primary microglial cells. These results indicated that cudratricusxanthone L (1) effectively repressed neuroinflammatory processes in BV2 and rat primary microglial cells by inhibiting NF-κB and the MAPK signaling pathway.

Manipulation of micro- and nano-sized objects with optical tweezers is a well established, albeit still evolving technique. While many objects can be trapped directly with focused laser beam(s), for some applications indirect manipulation with tweezers-operated tools is preferred. We introduce a simple, versatile micro-tool operated with holographic optical tweezers. The 40 µm long dumbbell-shaped tool, fabricated with two-photon laser 3D photolithography has two beads for efficient optical trapping and a probing spike on one end. We demonstrate fluids viscosity measurements and vibration detection as examples of possible applications.

An innovative wireless sensor network (WSN) based on Ultra-Wide Band (UWB) technology for 3D accurate superficial monitoring of ground deformations, as landslides and subsidence, is proposed. The system has been designed and developed as part of an European Life+ project, called Wi-GIM (Wireless Sensor Network for Ground Instability Monitoring). The details of the architecture, the localization via wireless technology and data processing protocols are described. The flexibility and accuracy achieved by the UWB two-way ranging technique is analysed and compared with the traditional systems, such as robotic total stations (RTSs), Ground-based Interferometric Synthetic Aperture Radar (GB-InSAR), highlighting the pros and cons of the UWB solution to detect the surface movements. An extensive field trial campaign allows the validation of the system and the analysis of its sensitivity to different factors (e.g., sensor nodes inter-visibility, effects of the temperature, etc.). The Wi-GIM system represents a promising solution for landslide monitoring and it can be adopted in conjunction with traditional systems or as an alternative in areas where the available resources are inadequate. The versatility, easy/fast deployment and cost-effectiveness, together with the good accuracy, make the Wi-GIM system a possible solution for municipalities that cannot afford expensive/complex systems to monitor potential landslides in their territory.

Parkinson’s disease (PD) is the most common cause of movement disorder characterized by the progressive loss of dopaminergic neurons in the substantia nigra. It is increasingly recognized as a complex group of disorders presenting widely heterogenous symptoms and pathology. Except for the rare monogenic forms, the majority of the PD cases result from an interaction between multiple genetic and environmental risk factors. The search for these risk factors and the development of preclinical animal models are in progress hand in hand, providing mechanistic insights into the pathogenesis of PD. This review summarizes the studies that capitalize on modeling sporadic (i.e. non-familial) PD using Drosophila melanogaster and discuss their methodology, new findings and future perspective.

The tryptophan (TRP)-kynurenine (KYN) metabolic pathway is a main player of TRP metabolism through which more than 95% of TRP is catabolized. The pathway is activated by acute and chronic immune responses leading to a wide range of illnesses including cancer, immune diseases, neurodegenerative diseases, and psychiatric disorders. The TRP-KYN pathway synthesizes multifarious metabolites including oxidants, antioxidants, neurotoxins, neuroprotectants, and immunomodulators. The immunomodulators are known to facilitate the immune system towards a tolerogenic state, resulting in chronic low-grade inflammation (LGI) that is commonly present in obesity, poor nutrition, exposer to chemicals or allergens, prodromal stage of various illnesses, and chronic diseases. KYN, kynurenic acid, xanthurenic acid, and cinnabarinic acid are aryl hydrocarbon receptor ligands that serve as immunomodulators. Furthermore, TRP-KYN pathway enzymes are known to be activated by the stress hormone cortisol and inflammatory cytokines, and genotypic variants were observed to contribute to inflammation and thus various diseases. The tryptophan 2,3-dioxygenase, the indoleamine 2, 3-oxygenases, and the kynurenine-3-monooxygenase are main enzymes in the pathway. This review article discusses the TRP-KYN pathway with special emphasis on its interaction with the immune system and the tolerogenic shift towards chronic LGI and overviews the major symptoms, pro- and anti-inflammatory cytokines, and toxic and protective KYNs to explore the linkage between chronic LGI, KYNs, and major psychiatric, including depressive disorder, bipolar disorder, substance use disorder, post-traumatic stress disorder, schizophrenia, and autism spectrum disorder.

Hair loss attributed to excessive stress from work and lifestyle changes has become a growing concern, particularly among young individuals. However, currently used drugs such as minoxidil and finasteride impose a plethora of side effects. Therefore, natural substances as alternatives have garnered research interest. A recent study showed the efficacy of Malva verticillata seed extracts in alleviating hair loss via upregulation of the Wnt/β-catenin signaling pathway. In this study, the efficacy of M. verticillata seed extracts on alleviation of hair loss was further investigated. Further fractionation and purification of the seed extracts using silica gel column chromatography and preparative high-performance liquid chromatography helped identify linoleic acid (LA) and oleic acid as the major bioactive components. LA insufficiency is reported to cause hair loss. However, its mechanism of action is not clearly known. Here, we explored the efficacy of LA treatment on preventing hair loss and its underlying mechanism of action. We found that LA treatment activated Wnt/β-catenin signaling and induced dermal papilla cell (DPC) proliferation in cell proliferation assays. Moreover, it increased the expression of cell cycle proteins such as cyclin D1 and cyclin-dependent kinase 2. LA treatment also increased the expression of vascular endothelial growth factor, insulin-like growth factor-1, hepatocyte growth factor, and keratinocyte growth factor in a concentration-dependent manner and significantly inhibited that of DKK-1, induced by dihydrotestosterone. These findings suggest that LA treatment induces hair growth by increasing DPC proliferation and alleviates androgenic alopecia by activating Wnt/β-catenin signaling in DPCs.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

Energy homeostasis is crucial for cell fate since all cellular activities are strongly dependent on the balance between catabolic and anabolic pathways. In particular, metabolic and energetic modulation has been reported in cancer cells long time ago, but have been neglected for a long time. Instead, during the past 20 years a recovery of the study of cancer metabolism has led to better consider metabolic alterations in tumors. Cancer cells must adapt their metabolism to meet the energetic and biosynthetic demands that accompany rapid growth of the primary tumor and colonization of distinct metastatic sites. They are largely dependent on aerobic glycolysis for their energy production and also are associated with increased fatty acid synthesis and increased rates of glutamine utilization. Emerging evidence has shown that therapeutic resistance to cancer treatment may arise due to deregulation in glucose metabolism, fatty acid synthesis, and glutamine utilization. Cancer cells exhibit a series of metabolic alterations induced by mutations leading to gain-of-function of oncogenes and loss-of-function of tumor suppressor genes that include increased glucose consumption, reduced mitochondrial respiration, increased reactive oxygen species generation and cell death resistance, all of which responsible for cancer progression. Cholesterol metabolism is also altered in cancer cells and supports uncontrolled cell growth. In this context, we review the roles of PPARs transcription factors, master regulators of cellular energetic metabolism, in the control and deregulation of energetic homeostasis observed in cancer. We highlight the different contribution of the different PPAR isotypes in different cancers and the differential control of their transcription in the different cancer cells.

Atmospheric correction is a necessary step in image processing data and spectra recorded by spaceborne sensors for pure cloudless atmosphere, primarily in the visible and near-IR spectral range. We have present a fast and sufficiently accurate method of atmospheric correction based on the proposed analytical solutions describing with high accuracy the spectrum of outgoing radiation at the top boundary of the cloudless atmosphere. This technique includes the model of the atmosphere and its optical parameters that are important in terms of radiation transfer. The solution of the inverse problem for finding unknown parameters of the model is carried out by the method of non-linear least squares (Levenberg-Marquardt algorithm) for an individual selected pixel of the image (its spectrum), taking into account the adjacency effects. Using the found parameters of the atmosphere and the average surface albedo, assuming homogeneity of the atmosphere within a certain area of the hyperspectral image (or the whole frame), the spectral albedo at the Earth's surface is calculated for all other pixels. It is essential that the procedure of the numerical simulation with non-linear least squares of the direct transfer problem is based on using analytical solutions, which provides a very short calculation time of the atmospheric parameters (seconds or less) and the ability to perform atmospheric correction "on-fly." Testing methods of atmospheric correction was performed using the synthetic outgoing radiation spectra at the top of the atmosphere (TOA), obtained by numerical simulation in the LibRadTran code, as well as spectra of real space images of the Hyperion hyperspectrometer. A comparison with the results of atmospheric correction in module FLAASH of ENVI package has been performed. Finally, to validate our data obtained by the SHARK method, a comparative analysis with ground-based measurements of Radiometric Calibration Network (RadCalNet) was carried out.

Some of the recent large-scale national projects in South Korea are delayed or suspended due to belated responses to risk occurring on site. Currently, the Far East District (FED) project is being implemented to relocate the US Army bases from Yongsan to Pyeongtaek. Because of lack of experience and understanding about the characteristics of such a project, the deadline of taking over to the US Army Korea has been missed. This study identifies problems of each participant in the Yongsan Relocation Plan (YRP) of the US Army Korea with respect to construction project management and establishes a risk management strategy reflecting characteristics of FED project. To derive significant risk factors influencing YRP, various field data like weekly and monthly reports and other reports on construction condition are analyzed, and experts’ advices are collected and a survey is conducted. Mediators and latent variables are ultimately obtained. Furthermore, a structural equation model is used to both analyze and evaluate complex causal relations among many variables of YRP. The impact of risk factors on the schedule, quality and cost of the project is analyzed. In particular, the case of Site A is examined to see how the project is affected by those risk factors.

The coexistence of human beings and environmental sustainability becomes individually and even globally concerned issue. In addition to environment issues, people also encounter negative issues of infectious diseases, gap between rich and poor, violence in society, uneven resource distribution, people’s health decline, and population structure aging, which would affect the sustainable development of cities. When taking sustainable development from the world to cities, it appears sustainable cities. The goal of a healthy city is to pursue the sustainability of a city. Aiming at residents in Shanghai, total 360 copies of questionnaire are distributed, and 277 valid copies are retrieved, with the retrieval rate 77％. The research results conclude that 1.“safety” is the most emphasized dimension, followed by “convenience & prosperity”, “sustainable ecology”, “vitality & health”, and “culture friendly” and 2.security, Internet city, pollution control, space use, and inheritance education are top five indicators, among 15 evaluation indicators. According to the results, suggestions are proposed to provide the government with correct, objective, and simply understandable healthy city indicators and sustainable development indicators for the appropriate planning and review of the administration objectives to enhance the public awareness of healthy city and the participation. It would stop the worsening of environment and promote residents’ health and the sustainable development of cities to have the city and the public moving towards healthy development.

A COVID-19 disease threatens the population and the economies of the countries significantly. Till now, this pandemic has affected 215 counties or territories. Unavailability of vaccine is the primary concern for the society. To avoid the spread of this disease, social isolation must be preserved and the inter and intra-population movement must be minimized. To reduce the possibility of transmission, the categorization of regions based on susceptibility to COVID-19 infection is a must.Due to the unavailability of a large amount of paper collection for this novel COVID-19 diseases, we used current literature available on a COVID-19 susceptibility of the diabetic patient, human reproductivity, hemodialysis patient’s, pregnant women and meteorological factors and geographical location. Countries in the cold region are more susceptible to the risk of COVID-19 transmission. There was no evidence of the spread of this disease from non-respiratory bodies. Diabetic patients and pregnant women were found to be more susceptible to COVID-19 infection. Anosmia was observed in the majority of the COVID-19 infected cases in European countries. No evidence indicates COVID-19's impact on the human reproductive system explicitly. No cases of vertical transmission of this disease have been observed until now. All the studies available till now is the small scale study. Correlation with something always does not mean causation. There are certain factor like pollution level, temperature Diurnal temperature range, geographical factor, humidity, pollution level, wind speed, population density, medical healthcare facilities social and political factor plays a critical role in transmitting the SARS-COV-2 virus. Besides the adverse effects, it has taught us to shed our selfish goals and to promote the welfare of all.

To evaluate whether autologous mesenchymal cells, adipose derived stem cells and platelet-rich plasma, grafted into the supracoroideal space by surgical treatment according to Limoli retinal restoration technique (LRRT), can produce growth factors in order to exert a beneficial effect in retinitis pigmentosa (RP) patients. Twenty-one eyes underwent surgery and divided based on retinal foveal thickness ≤ 190 or >190 µm into group A and group B, respectively. The specific LRRT triad was grafted in a deep scleral pocket above the choroid of each eye. At 6-month follow-up, group B showed an improvement in residual close-up visus and sensitivity at microperimetry compared to group A. After an in-depth review of molecular biology studies concerning degenerative phenomena underlying the etiopathogenesis of RP, it can be confirmed that further research is needed on tapeto-retinal degenerations both from a clinical and molecular point of view to obtain better functional results. In particular, it is necessary to increase the number of patients, extend observation times, and treat subjects in the presence of still trophic retinal tissue to allow adequate biochemical and functional catering.

The combination of increased pressures for high-volume, high-impact publications in English language with the high rejection rates of submitted manuscripts for publications presents an often unsurpassable obstacle for (early career) researchers. At the same, the register requirements of peer-reviewed journals -that can contribute to whether a paper is accepted for publication- has received little attention. This paper redresses this gap, by investigating the linguistic choices in 60 published manuscripts in four journals, with impact factor (IF) above 2; all 4 journals, publish original research papers in the field of chemical engineering science and specifically focus on wastewater treatment. Our survey shows that chemical engineering research publications tend to comply to a set of unwritten requirements: multidisciplinarity, brevity, co-authorship, focus on the description of practical results (rather than methods), and awareness of non-specialised audiences. It is found that less discipline-specific vocabulary was used in higher IF journals and this is interpreted within the current context of manuscript publication and consumption. Also, a complex relationship between the advertised scope of each journal and the actual published papers exists, indicating that guide for authors and aims and objective published by the journal's editorial office should be critically evaluated.

Landslides are a frequent and recurrent problem in hilly regions of India and predicting them is always a challenging task. In this paper, an attempt was made to deal with this problem using advanced physical and numerical modeling methods. Detailed understanding of the initial slope failures is very interesting, and challenging at the same time, in the design and development of wireless sensor network based on early warning of landslide monitoring. A small scale physical model was developed to assess the instability through a sensor network with variable rain fall intensity. This was achieved by increasing the simulated rain water flow intensity in different time spans (dry condition, at t=0 to t= 30 min, 0.5 mm/min at t=30 to t= 60 min, 0.75 mm/min at t=60 to t=91 min and 1 mm/min at t=91 to t= 120 min). The water level and movement in the slope was recorded by rainfall sensor, vibration sensor, soil moisture sensor and a digital camera. The following changes were observed during the slope failure: a) movement of small particles at top of the slope; b) initial failure of medium size soil particle; c) scouring of soil mass; d) whole slope collapse. The obtained results clearly indicated the superiority and effectiveness of the proposed system in providing a factor of safety for the progressive slope.

We know that the classical Mittag-Leffler function play an important role as solution of fractional order differential and integral equations. We introduce the j-generalized p - k Mittag-Leffler function. We evaluate the second order differential recurrence relation and four different integral representations and introduce a homogeneous linear differential equation whose one of the solution is the j-generalized p-k Mittag-Leffler function. Also we evaluate the certain relations that exist between j-generalized p - k Mittag-Leffler function and Riemann-Liouville fractional integrals and derivatives. We evaluate Mellin-Barnes integral representation of j-generalized p-k Mittag-Le er Function. The relationship of j-generalized p-k Mittag-Leffler Function with Fox H-Function and Wright hypergeometric function is also establish. we obtained its Euler transform, Laplace Transform and Mellin transform. Finally we derive some particular cases.

Growth-regulating factor (GRF) is a plant-specific transcription factor family, which is involved in nearly all of the central developmental processes in plants. However, little is known about GRF family genes in cultivated sunflower. In this study, 17 GRF genes were identified and characterized from sunflower genome. Their gene structures, conserved motifs, chromosomal distributions and phylogenetic relationships were analyzed. The expression patterns of these genes were detected in various tissues of sunflower inbred line SK02R, which revealed that the 10 seed-specific GRF genes may play important roles during seed development in sunflower. Additionally, transcripts changes of the GRFs under two major abiotic stresses and phytohormones showed that most of the detected GRFs were reduced significantly by GA3 treatment, and other treatments(ABA, NaCl and PEG6000) differently regulated various sunflower growth-regulating factors at different time points. MiR396 target analysis indicated that there may exist a complicated homeostasis between miR396 and its targets GRF and WRKY transcription factor genes in cultivated sunflower. The phylogenetic and expression analyses of the GRF gene family in sunflower would be useful for further cloning and function exploration of the HaGRF genes.

In this paper we introduce the New/Generalized two parameter Gamma function and Pochhammer symbol. We named them, as Generalized p - k Gamma Function and Generalized p - k Pochhammer symbol and denoted as $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ respectively. We prove the several identities for $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ those satisfied by the classical Gamma function. Also we provide the integral representation for the $ _{p}^{a}\Gamma_{k}(x) $

Today, buildings are increasingly designed with transparent materials, with glass paneling being especially popular as an installation material for its architectural allure. However, its major drawback is admitting impractical amounts of sunlight to interior spaces. Office buildings with excessive sunlight in indoor areas result in worker inefficiency. This article studied kinetic façades as means to providing suitable sunlight for interior spaces integrated with a triple identity of DNA structure, photosynthetic behavior, and the twist used, which was divided into generation and evaluation. The generating phase first used an evolutionary engine to produce potential strip patterns. The kinetic façade was subsequently evaluated by Climate Studio software to validate daylight admission in an indoor space with Leadership in Energy and Environmental Design (LEED) version 4.1 criteria. To analyze the kinetic façade system, the building envelope was divided into four types: glass panels, static façades, kinetic façade (version 1, rotating movement), and kinetic façades (version 2, twisting movement). In addition, for kinetic façades, degrees of simulation for versions 1 and 2 were 20, 50, 80, and 100 degrees, in order to ascertain potential for both façades to the same degree. Comparing all façades receiving the daylight factor (DF) into the space from more or less sunlight resulted in the decreasing order of potential as follows: entirely glass façade, kinetic façade version 2, kinetic façade version 1, and static façade. By receiving daylight factor (DF), the façade filtered appropriate amounts of daylight into the working space moderately and beneficially. Daylight simulation results indicated that the newly designed kinetic façade (version 2) had more potential than other building envelope types in terms of filtering beneficial daylight in indoor areas. This article also experimented with the kinetic façade prototype in an actual situation to test conditional environmental potential. The kinetic façade (version 2) was explored in the building envelope with varied adaptability in order to provide sunlight and for private-to-public, public-to-private, or semi-public working areas.

Chloracne is the major skin symptom caused by dioxin intoxication. Dioxin activates the aryl hydrocarbon receptor (AHR)–cytochrome p450 1A1 (CYP1A1) system, generates oxidative stress, and induces hyperkeratinization of keratinocytes and sebocytes leading to chloracne. Nuclear factor-erythroid 2-related factor-2 (NRF2) is a master switch inducing expression of various antioxidative enzymes such as heme oxygenase-1. Cinnamaldehyde is an antioxidant phytochemical that inhibits AHR–CYP1A1 signaling and activates the NRF2–antioxidative axis. The cinnamaldehyde-containing Kampo herbal medicine Keishibukuryogan is capable of improving chloracne in Yusho patients who are highly contaminated with dioxin. Agents with dual functions in promoting AHR–CYP1A1 inhibition and NRF2 activation may be useful in managing dioxin-related health hazards.

Environmental assessment is a concept that has been designed to facilitate the present generation to meet their needs without compromising the ability of future generations to meet their own needs as well. Thus, this concept has drawn significant attention from various scholars, researchers and industrial practitioners around the world over the past three decades. Life Cycle Environmental Assessment (LCEA) is a widely metric used to assess the potential ecological impacts, which can be caused by electricity generating supply systems or by other systems than power production plants. However, the current LCEA model is biased and ineffective. Because, its omits factors that are increasingly contributing to the ecological degradation. This study has identified the omitted factors through a critical analysis of a set of previous journal articles conducted in the energy sector. In light of this, this study has developed a novel LCEA framework addressing those blind spots. The framework developed in this study is holistic in nature including all the life cycle stages of a power supply system such as Extraction of the Raw Material (ERM), Transport of Raw Material (TRM), Conversion of Raw into Electricity (CRE), and Transmission and Distribution of Electricity (TDE) to the end users. The novel developed LCEA model has been tested and applied to nine power generation plants such as coal, gas, nuclear, biomass, geothermal, hydro, solar thermal, wind onshore and wind offshore. The results have demonstrated that of conventional technologies including coal, gas, and nuclear, coal energy generating source has got the highest life cycle greenhouse gas Grid Emission Factor (GEF) of 2866 kg CO2e/MWh, followed by gas with 728 kg CO2e/MWh, and nuclear has got the least GEF of 35 kg CO2e/MWh. Whereas of renewable energy sources biomass has got the highest GEF of 1508 kg CO2e/MWh, followed by solar thermal with 46.6 kg CO2e/MWh, hydro 39 kg CO2e/MWh, wind offshore 25.25 kg CO2e/MWh, wind onshore 10.1 kg CO2e/MWh, and geothermal closes the ranking with 6.23 kg CO2e/MWh.

This paper gives a new unified formula for the Newtonian fluids valid for all pipe flow regimes from laminar to the fully rough turbulent. It includes laminar, unstable sharp jump from laminar to turbulent, and all types of the turbulent regimes: smooth turbulent regime, partial non-fully developed turbulent and fully developed rough turbulent regime. The formula follows the inflectional form of curves as suggested in Nikuradse’s experiment rather than monotonic shape proposed by Colebrook and White. The composition of the proposed unified formula consists of switching functions and of the interchangeable formulas for laminar, smooth turbulent and fully rough turbulent flow. The proposed switching functions provide a smooth and a computationally cheap transition among hydraulic regimes. Thus, the here presented formulation represents a coherent hydraulic model suitable for engineering use. The model is compared to existing literature models, and shows smooth and computationally cheap transitions among hydraulic regimes.

This article focuses on the current state-of-the-art in the area of cellular and molecular biotechnology for over-production of clinically relevant therapeutic growth factors and how the technology can be used for the treatment of osteoarthritis (OA). Transfected and irradiated protein packaging cell lines may be used as “cellular factories” for large-scale production of therapeutic proteins and pro-anabolic growth factors, particularly in the context of cartilage matrix regeneration. We discuss the potential for new innovations in regenerative medicine for degenerative diseases of synovial joints using mammalian protein production platforms, specifically protein packaging cell lines, for over-producing growth factors for cartilage tissue regeneration and give recent examples. Mammalian protein production platforms that incorporate protein packaging cell lines are superior to bacterial expression systems and are likely to have a significant impact on the development of new biological therapies for treating focal cartilage defects and more generally for the treatment of degenerative joint diseases such as OA.

The node position information is critical in the wireless sensor network (WSN). However, the existing positioning algorithms commonly have low positioning accuracy because of noise interferences in communication. To solve this problem, this paper presents an iterative positioning model based on distance correction to improve the positioning accuracy of the target node in WSN. First, the log-distance distribution model of received signal strength indication (RSSI) ranging is built and the noise impact factor is derived based on the model. Second, the initial position coordinates of the target node are obtained based on the triangle centroid localization algorithm, thereby calculating the distance deviation coefficient under the influence of noise. Then, the ratio of the distance measured by the log-normal distribution model to the median distance deviation coefficient is taken as the new distance between the anchor node and the target node. Based on the new distance, the triangular centroid positioning algorithm is used again to calculate the target node coordinates. Finally, the iterative positioning model is constructed, and the distance deviation coefficient is updated repeatedly to update the positioning result until the set number of iterations is reached. Experiment results show that the proposed iterative positioning model can improve positioning accuracy effectively.

The main regulatory factors during the adaptation of cancer cells to hypoxic stress are the hypoxia-inducible factors (HIFs), which are being increasingly recognized as an interesting and challenging target for the design of new chemotherapeutic molecules. HIF2A was found to have an large internal hydrophilic cavity within its PAS-B domain, unique to this sub-unit and is suggested to be a possible ligand-binding site. Regulation of HIF2A by cellular molecules is still greatly unknown. In This paper we have employed in-silico techniques, such as molecular docking and dynamic simulation, to design new direct inhibitors against HIF-2A subunit via targeting one of its critical domains and the final top screened molecules have been tested on hypoxic cancer cells for further validation of their inhibitory potential. we targeted the hydrophilic cavity inside the PAS-B domain of the HIF2A to identify novel molecules with a high binding capacity. Virtual Screening methodology was used for molecular docking of NSC library against the target domain inside the HIF2A PAS-B domain with the top 5% compounds with significant MolDock and Re-rank scores were selected for further analysis. The NSC 106416, NSC 217021, NSC 217026, and NSC 215639 compounds were selected based on their docking scores. NSC 215639 had the minimum polar solvation energy and also had a relative strong binding energy. NSC 217026 had the strongest binding energy among other compounds.

In this paper, we present a novel Two-Echelon Ground Vehicle and Its Mounted Unmanned Aerial Vehicle Cooperated Routing Problem (2E-GUCRP). The 2E-GUCRP arises in the field of Unmanned Aerial Vehicle (UAV) Routing Problem such as those encountered in the context of city logistics. In a typical cooperated system, the UAV is launched from the Ground Vehicle (GV) and automatically flies to the designated target. Meanwhile, acting as a mobile base station, the GV can charge or change the UAV’s battery on the designated landing points to enable the UAV to continue its mission. The objective is to design efficient GV and UAV routes to minimize the total mission time while meeting the operational constraints. A Mixed Integer Programming (MIP) model, which could be solved by commercial software, is constructed to describe this problem. In order to quickly solve the medium-scale problems, two existing heuristics to solve 2E-VRP are improved. The computational experiments are set up to compare our model with the 2E-VRP. The results indicate that the 2E-GUCRP obtains a better efficiency. Further discussion of the practical instance points out that the increase in efficiency is related to the speed relationship between the GV and the UAV.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

The Connor–Davidson Resilience Scale (CD-RISC) and the Brief Resilience Scale (BRS) are two widely used scales to measure resilience. Although both scales seek to assess an individual’s ability to recover from and adapt to disruptions or stressful events, they may capture different aspects of resilience. While the CD-RISC focuses on resources that can help individuals recover from and adapt to disruptions or stressful events, the BRS directly measures one’s ability to bounce back or be resilient. The aim of this study is to empirically examine the differences between the CD-RISC and the BRS. Two samples (n = 202, 246) consisting of undergraduate students from Taiwan were used. The results of confirmatory factor analysis show that the CD-RISC and the BRS are highly correlated but still distinct. The results of regression analyses show that the CD-RISC and the BRS have unique predictive effects on depression and life satisfaction. The research findings suggest that the CD-RISC and the BRS capture different aspects of resilience. For future research on resilience, researchers should pay attention to the differences between these scales and choose the one that most closely fits their research purpose.

The evaluation of the piezoelectric properties of ferroelectric ceramics generally has a high level of uncertainty, due to incomplete poling, porosity, domain wall clamping and other effects. In addition, the poling process is often difficult and dangerous, due to the risk of breaking or damaging the sample. A method is described for the evaluation of the potential intrinsic piezoelectric response that a ceramic would have after full poling, without poling it. The method relies on the fact that any material undergoes an elastic softening below the ferroelectric transition temperature, whose magnitude can be expressed in terms of the intrinsic piezoelectric and dielectric coefficients of the material. Such a softening is equivalent to an electromechanical coupling, averaged over all the components due to the unpoled state of the sample, and can be deduced from a single temperature scan of an elastic modulus of a ceramic sample, spanning the ferroelectric and paraelectric states. The strengths, limits and possible applications of the method are discussed.

An important moment in the establishment of forestry seed orchards is the formation of their optimal composition, avoiding inbreeding depression in the outgoing seed material which occurs due to crossbreeding between closely related plus trees, the clones of which comprise the orchards. It is possible to minimize the negative effect of inbreeding by considering the hereditary aspect of the heterogeneous seed orchard material. The purpose of our work is to provide a comparative assessment of the formation and lignification of xylem in annual shoots of the plus trees of Scots pine. We investigated the formation and lignification of xylem in the annual shoots of the plus trees of Scots pine (Pinus sylvestris L.), found in natural forests in the Nizhny Novgorod region of the Russian Federation. Their vegetative progeny were cultivated in the clone archive stationed in the same region. Analyzing the one-type of the 1-year shoots, the time that the shoots were cut from the branches corresponded to the presence of plants in the characteristic phenological phases of seasonal development. A histochemical study of xylem was conducted, using the qualitative reactions of phloroglucinol to lignin. The power of xylem development was estimated by counting, in the radial direction, the cell rows from the core to the cambium in the microscope’s field of view. A significant differentiation of plus trees was revealed in a complex of signs characterizing the level of xylem development and the degree of xylem cell lignification in the tissues of annual shoots. Phenotypic differences in the physiological state of plus trees appeared given a leveled ecological background, indicating their genotypic determinism. This was confirmed by an analysis of variance. The share of the influence of differences between the proper plus trees was between 25.16% ± 8.91% and 53.98% ± 5.48% of the total phenotypic variance of the signs of the seasonal state of xylem. Factor analysis was used to reduce the number of considered indicators of xylem physiological state. The results allowed a cluster analysis to be carried out on the basis of the normalized values of the initial xylem features as well as the principal components derived from them. The association of plus trees was done on the basis of the similarity of the multidimensional estimates of xylem seasonal condition. The objects that were the most remote from the others were identified. This information provides a reasonable approach to the formation of an assortment of Scots pine seed orchards.

Recent studies have indicated that several anti-hypertensive drugs may delay the development and progression of Alzheimer’s disease (AD). However, the relationships among AD, hypertension, and oxidative stress remain to be elucidated. In the present study, we aimed to determine whether treatment with resveratrol reduces reactive oxygen species (ROS) generation in the brain, thereby reducing cognitive impairment in rats with angiotensin II (Ang-II)-induced early AD. Male WKY rats with Ang-II-induced AD were treated with losartan or resveratrol for 2 weeks. Our results revealed that treatment with resveratrol (10 mg/kg/day) decreased blood pressure, increased levels of brain-derived neurotrophic factor (BDNF) in the hippocampus, and decreased ROS production in the nucleus tractus solitarius (NTS) in the Ang-II groups. In addition, inhibition of Tau^T231 phosphorylation in the hippocampus using resveratrol significantly abolished Ang-II-induced expression of Ab precursors, active caspase 3, and glycogen synthase kinase 3b (GSK-3b)^Y216 while increasing Akt^S473 phosphorylation. Notably, resveratrol reversed impairments in hippocampal-dependent contextual memory induced by deleting NADPH oxidase and NOX2. Overall, our results suggest that resveratrol exerts neuroprotective effects against memory impairment and hippocampal damage in a rat model of early stage AD by reducing oxidative stress. These novel findings indicate that resveratrol may represent a pharmacological option for patients with hypertension at a risk of AD during old age.

Palmitic acid metabolism involves delta-9 and delta-6 desaturase enzymes forming palmitoleic acid (9cis-16:1; n-7 series) and sapienic acid (6cis-16:1; n-10 series), respectively. The corresponding biological consequences and lipidomic research on these positional MUFA isomers are under development. Furthermore, sapienic acid can bring to the de novo synthesis of the n-10 polyunsaturated fatty acid (PUFA) sebaleic acid (5cis,8cis-18:2), but such transformations in cancer cells are not known. The model of Caco-2 cell line was used to monitor sapienic acid supplementation (150 and 300 μM) and evidence the formation of n-10 fatty acids as well as their incorporation at levels of membrane phospholipids and triglycerides. Comparison with palmitoleic and palmitic acids evidenced that lipid remodeling was influenced by the type of fatty acid and positional isomer, with increase of 8cis-18:1, n-10 PUFA and decrease of saturated fats in case of sapienic acid. Cholesteryl esters were formed only in case of sapienic acid. EC₅₀ of sapienic acid (232.3 μM at 96 hrs) was the highest found among the tested fatty acids, thus influencing cell viability that was only reduced at 25% at 300 μM, whereas palmitoleic acid induced cell death. Two-photon fluorescent microscopy with Laurdan as a fluorescent dye provided information on membrane fluidity, highlighting that sapienic acid increases the distribution of fluid regions, probably connected with the formation of 8cis-18:1 and the n-10 PUFA in cell lipidome. Our results bring evidence for MUFA positional isomers and de novo PUFA synthesis for developing lipidomic analysis and cancer research.

Cachexia is a syndrome characterized by an ongoing loss of skeletal muscle mass associated with poor patient prognosis in non-small cell lung cancer (NSCLC). However, prognostic cachexia biomarkers in NSCLC are unknown. Here, we analyzed computed tomography (CT) images and tumor transcriptome data to identify potentially secreted cachexia biomarkers (PSCB) in NSCLC patients with low-muscularity. We integrated radiomics features (pectoralis muscle, sternum, and T10 vertebra) from CT of 89 NSCLC patients, which allowed us to identify an index for screening muscularity. Next, a tumor transcriptomic-based secretome analysis from these patients (discovery set) was evaluated to identify potential cachexia biomarkers in patients with low-muscularity. The prognostic value of these biomarkers for predicting recurrence and survival outcome was confirmed using expression data from eight lung cancer datasets (validation set). Finally, C2C12 myoblasts differentiated into myotubes were used to evaluate the ability of the selected biomarker, IL-8, in inducing muscle cell atrophy. We identified 75 over-expressed transcripts in patients with low-muscularity, which included IL6, CSF3, and IL8. Also, we identified NCAM1, CNTN1, SCG2, CADM1, IL8, NPTX1, and APOD as PSCB in the tumor secretome. These PSCB were capable of distinguishing worse and better prognosis (recurrence and survival) in NSCLC patients. IL8 was confirmed as a predictor of worse prognosis in all validation sets. In vitro assays revealed that IL-8 promoted C2C12 myotube atrophy. Tumors from low-muscularity patients presented a set of upregulated genes encoding for secreted proteins, including pro-inflammatory cytokines that predict worse overall survival in NSCLC. Among these up-regulated genes, IL8 expression in NSCLC tissues was associated with worse prognosis and the recombinant IL-8 was capable of triggering atrophy in C2C12 myotubes.

In South Korea, landslides are caused by localized heavy rainfall and typhoons, which often occur in the summer season at natural slopes in mountainous areas and artificial slopes in urban surroundings. Flow-type landslides frequently occur in mountainous areas. To evaluate flow-type landslides, it is essential to identify the physical characteristics of soil, giving focus to the soil on the top layers of various types of slope. This study conducts a survey and an analysis of the characteristics of landslides that occurred in the study area with different geological conditions of granite and gneiss. The characteristics of soil in the area and its surroundings that have or have not undergone landslides for every geological condition is also evaluated. Based on these characteristics and a statistics method, it extracts the triggering factors, permeability coefficients (k), and shearing strength with cohesion (c) and internal friction angel (φ) of soils that are highly related to landslides around weathered soil layers. As a result, the permeability coefficients show significant relevance with void ratio (e), the effective size of grains (D10), and uniformity coefficient (cu), while the shearing strength with the proportion of fine-grained soil (Fines), uniformity coefficient (cu), degree of saturation (S), dry weight density (rd), and void ratio (e). By obtaining this result, the study uses the regression analysis to suggest models to estimate the permeability coefficients and shearing strength. For the gneiss area, the statistics-based estimation model (SEM) is proposed as k_gn = (1.488 × 10^-02 × e) + (1.076 × D₁₀) + (-1.629 × 10^-04 × c_u) - (1.893 × 10^-02) for permeability coefficients; cgn = (-0.712 × Fines) + (-0.131 × c_u) + 15.335 for cohesion; and φgn = (27.01 × r_d) + (-12.594 × e) + 6.018 for internal frictional angle of soils. For the granite area, the statistics-based estimation model (SEM) is proposed as kgr = (8.281 × 10^-03 × e) + (0.639 × D₁₀) + (-2.766 × 10^-05 × c_u) - (9.907 × 10^-03) for permeability coefficients; c_gr = (-0.689 × Fines) + (-0.0744 × S) + 18.59 for cohesion; and φ_gr = (33.640 × r_d) + (-0.875 × e) - 9.685 for internal frictional angle of soils. The use of statistics-based estimation models (SEMs) for landslide-triggering factors that trigger landslides will support the simple calculation of permeability coefficient and shearing strength (cohesion and internal frictional angle), only requiring information about the physical properties of soil at the natural slopes that have different geological features such as gneiss and granite areas.

To solve the problem of the origin of homochirality of living systems and life itself, it is necessary to rethink the conceptual foundations of physics dialectically. The review shows how this can be done within the framework of the paradigm of energoforms, which sets the principles of construction and mathematical formalization of the Heraclitus primary element of matter. The algorithm for modeling energoforms and structures of elementary particles was created based on the laws of dialectics, electromagnetic induction and the rules of quantum physics. The algorithm allowed to calculate the parameters of chiral structures of neutron, proton, electron, neutrino and photon in the ground and excited states, as well as the parameters of more than one hundred nuclei. As an adequate solution to the problems of neutrino physics and the nature of the universal chiral factor, we hypothesized the instability of the low-energy solar neutrino and the biogenicity of its decay products – chiral energoforms. The hypothesis was based on correlations of seasonal and daily variations of solar neutrino flux, optical activity of aqueous solutions of sugars and metabolism of plants and animals. In humans, chiral morphofunctional features that limit homeostasis and the rhythm of energy-informational connections of the brain with the external environment were revealed. It was shown that the mechanism of sensitivity of living matter to the action of chiral factor is based on the ability to self-organization of its cooperative water-containing systems consisting of spin homogeneous chiral elements.

Background: Cyber Security is to protect online data and software from cyber threats. These cyberattacks are typically intended to gain access to, change, or delete sensitive information; extort money from users; or disrupt regular corporate activities. It is difficult to keep up a regular follow up with new technologies so it is necessary to keep the important data safe from cyber threats. There are many types of cyber threats; malware, ransom-ware, social engineering, phishing etc. To prevent cyber-attacks one can use password manager tools like LastPass and others. People also use two factor authentication for double security on their accounts. Methods: Boards such as the National Institute of Standards and Technology (NIST) are developing frameworks to assist firms in understanding their security risks, improving cybersecurity procedures, and preventing cyber assaults. The fight against cybercrimes and attack, rganisations needed a strong base there are 5 types of cyber securities; Critical Infrastructure Security, application security, network security, cloud security and (IoT) Security. In the modern time US is highly based on computers and on different software so it is really important for US to be more conscious about the security as they get many threats almost everyday for hacking their data and accounts.Results and Conclusion: Nowadays, even small businesses rarely recover their loss from the cyber-attacks and many back-off from continuing their businesses after being target of hackers. The first cybercrime attack was recorded on 1988 by a graduate student. Now that large companies and even small businesses are aware of cyber-attacks so they try their best to take every precaution to prevent the hacking with double security and password manager tools.

The continuous development in the field of industrial automation and electric mobility has led to the need for more efficient electrical machines with high power density. The improvement of electrical machines slot filling factors is one of the measures to satisfy these requirements. In recent years, this topic has aroused greater interest in the industrial sector, since the evolution of the winding technological manufacturing processes allows an economically sustainable realization of ordered winding arrangements, rather than random ones. Moreover, the manufacture of electrical machines windings must be preceded by an accurate design phase in which it is possible to evaluate the maximum slot filling factor obtainable for a given wire shape and for its dimensions. For this purpose, this paper presents an algorithmic approach for the evaluation of maximum slot filling factors in electrical machines under ideal geometric premise. In particular, this algorithm has a greater degree of flexibility with respect to the algorithm approaches found in the literature, since the study has been extended to round, rectangular and hexagonal wire sections. Furthermore, the slot filling factor calculation was carried out both for standard and non-standard slots. The algorithmic approach proposed can be considered as an additional useful tool for the fast design of electrical machine windings.

Matrix metalloproteinase 3 (MMP3) plays multiple roles in pro-tumorigenic proteolysis and in intracellular transcription. These include inducing connective tissue growth factor [CTGF, also known as cellular communication network factor 2 (CCN2)] and prompting a new definition of MMP3 as a moonlighting metalloproteinase. Members of the MMP family have been found within tumor-derived extracellular vesicles (EVs) such as oncosomes or exosomes. We here investigated the roles of MMP3-rich oncosomes in tumor progression, molecular transmission, and gene regulation. MMP3 and CCN2/CTGF were significantly co-expressed in tumor samples derived from patients suffering from colorectal adenocarcinoma. We found that oncosomes derived from a rapidly metastatic colon cancer cells (LuM1) were enriched in MMP3 and a C-terminal half fragment of CCN2/CTGF. MMP3-rich oncosomes were highly transmissive into recipient cells and were pro-tumorigenic in an allograft mouse model. Oncosome-derived MMP3 was transmissive into recipient cell nuclei, trans-activated CCN2/CTGF promoter, and induced CCN2/CTGF production at 1 to 6 hours after the addition of oncosomes to culture media. In addition, CRISPR/Cas9-mediated knockout of MMP3 showed significant anti-tumor effects, including inhibition of migration and invasion of LuM1 cells in vitro, inhibition of tumor growth in vivo, and reduction of CCN2/CTGF and its promoter activity in vitro. These data newly demonstrate that the oncosome-derived moonlighting metalloproteinase promotes metastasis and is pro-tumorigenic at distant sites as well as a transmissive trans-activator for the cellular communication network gene.

Interaction of an electromagnetic field with matter in a laser cavity without the assumption of a fixed direction of the transverse electric field, described by the two-level Maxwell-Bloch equations, is studied. By using a perturbative nonlinear analysis, performed near the laser threshold, we report on the derivation of the laser (3+1)D vectorial complex cubic-quintic complex Ginzburg-Landau equation. Furthermore, we study the modulational instability of the plane waves both theoretically using the linear stability analysis, and numerically, using direct simulations via the split-step Fourier method. The linear theory predicts instability for any amplitude of the primary waves. Our numerical simulations confirm the theoretical predictions of the linear theory as well as the threshold of the amplitude of perturbations. The system understudy shows a deep dependence on the laser cavity parameters, for which there appear wave patterns in accordance with the predictions from the gain spectrum.

The feed-forward loop (FFL) is an important and basic network motif to understand specific biological functions. Cyclic-AMP (cAMP) receptor protein (CRP), a transcription factor (TF), mediates catabolite repression and regulates more than 400 genes in response to changes in intracellular concentrations of cAMP in Escherichia coli. CRP participates in some FFLs like araBAD and araFGH operons and adapt to fluctuating environmental nutrients thus enhancing the survivability of E. coli. Although computational simulations have been used to explore the potential functionality of FFLs, a comprehensive study of the functions of all structural types based on in vivo data is lacking. Also, the regulatory role of CRP-mediated feed-forward loops (CRP-FFLs) remain unclear to date. Using EcoCyc and RegulonDB, we identified 393 CRP-FFLs in the E. coli. Dose-response genomic microarray of E. coli revealed dynamic gene expression of each target gene of CRP-FFLs in response to a range of cAMP dosages. All eight types of FFLs were present in CRP regulon with various expression patterns of each CRP-FFL, that were further divided into five functional groups. Microarray and reported regulatory relationships identified 202 CRP-FFLs which were directly regulated by CRP in these eight types of FFLs. Interestingly, 30% (147/482) of genes were directly regulated by CRP and CRP-regulated TFs, indicating that these CRP-regulated genes were also regulated by other CRP-regulated TFs responding to environmental signals through CRP-FFLs. Furthermore, we applied gene ontology annotation to reveal the biological functions of CRP-FFLs.

The mind-body problem is the central issue in both of philosophy and life science for several centuries. To date, there is still no conclusive theory to interpret the relation between the mind and the body, even just the mind alone. Here, we promote a novel model, a derived mathematic equation called the entropic system equation, to describe the innate characters of the mind and the mechanism of the mind-body coupling phenomenon. As the semi-open thermodynamic systems far from equilibrium, the living organisms could be logically considered as an entropic system. In the living organisms or the entropic systems, there also are three essential existing elements including mass, energy and information, in which the mind and the body are hypothetically coupled by free energy and entropic force.

In this work, it is analyzed a Digital Signal Processor, DSP, based One Cycle Control, OCC, strategy for a Power Factor Corrector, PFC, rectifier, which presents Common-mode Voltage, CMV, immunity. The proposed strategy utilizes an emulated-resistance-controller in closed-loop configuration to set up dc-link voltage and achieve unity power factor, UPF. It is shown that if PFC can achieve UPF condition and if phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator, LLC, to average phase current. Another possible condition is also analyzed. The proposal is verified by simulation and experiments.

The climate covers a series of events that deeply affect human life. It is possible to understand these events through spatial and statistical analyzes. Today, climate change, which is one of the most important of these events and the impact factors of consequences of this change, become a current issue. Drought is cited as one of the consequences of climate change and it is important to examine it with various methods as it can give negative results to both the economy and the nature. In this study, the drought status of the regions where these stations are located and the effects of drought on climate change were statistically calculated and evaluated using Standardized Precipitation Index (SPI), Percentage of Normal Index (PNI), Aridity Index (AI) and Standardized Precipitation -Evopotranspiration Index (SPEI). The precipitation data from 1981 to 2010 were obtained from Cihanbeyli, Karapınar, Çumra, Seydişehir, Kulu, Ereğli, Niğde, Karaman, Beyşehir and Aksaray meteorology stations affiliated to Turkish State Meteorological Service. At the same time, factor analysis and validity-reliability analysis were conducted to test the computability of the indices used in the study as a single index and to determine the reliability of the operations. While using exploratory factor analysis, Kaiser-Meyer-Olkin (KMO) test and Barlett test for factor analysis; Cronbach's alpha coefficient was used for reliability analysis. In our study, K-Means Cluster Analysis method was performed to determine the cutoff values of indices. According to the result of cluster analysis for the new (common) index, new clusters were created and ANOVA test was conducted to determine whether there was a difference between clusters.

In this letter, it is proposed that cryogenic quantum bits could operate based on the nonlinearity due to the quantum capacitance of two-dimensional Dirac materials, and in particular graphene. The anharmonicity of a typical superconducting quantum bit is calculated and the sensitivity of quantum bit frequency and anharmonicty with respect to temperature are found. Reasonable estimates reveal that a careful fabrication process could reveal the expected properties, thus putting the context of quantum computing hardware into new perspectives.

Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

In the second decade of the 21st century, social media changed the nature of communication and cooperation between participants of the culture services market. They became, among other things, an important marketing instrument in the area of contact with the customers of the cultural offer. However, despite their growing importance in various areas of activity of organisations in the cultural sector, the issue of building the cultural institution's brand equity by social media users is relatively seldom raised. Research on the impact of online consumer activity on brand equity is at an early stage of development. Therefore, this article is an attempt to fill the research gap in this area. The article presents the results of a survey conducted in 2018 on a group of 1021 consumers of cultural services, who at the same time regularly used social media. The statistical analysis carried out and the research results obtained prove that the 3C sustainable system developed by the authors, concerning the activity of consumers of cultural services in social media, stimulates the consumer-based brand equity (CBBE). Statistically significant relations have been observed in particular for CBBE components related to the awareness of a cultural institution's brand and for the relationship related to the perception of its quality. The study opens a review of literature on social media and consumer-based brand equity (CBBE). Next, based on the COBRA model (consumer's online brand-related activities), a proposal of the 3C sustainable system, concerning the activity of consumers of cultural services in social media, has been presented. The further part of the article presents research hypotheses, a conceptual model, research methodology as well as results and conclusions. The last part of the article discusses the results obtained and indicates the existing management implications.

Understanding cell migration is a key step to unravel many physiological phenomena and predict several pathologies, like cancer metastasis. In particular, mechanical confinement has been proved to be a key factor in the cellular migration strategy choice. As our insight in the field improves, new tools are needed in order to empower biologists’ analysis capabilities. In this framework, microfluidic devices have been used to engineer the mechanical stimuli and to investigate cellular migration response in a more controlled way. In this work, we will review the existing technologies employed in the realization of microfluidic cellular migration assays, namely soft lithography of PDMS and hydrogels and femtosecond laser micromachining. We will give an overview of the state of the art of these devices, focusing on the different geometrical configurations that have been exploited to study specific aspects of cellular migration. Our scope is to highlight the advantages and possibilities given by each approach and to envisage the future developments in in-vitro migration studies under mechanical confinement in microfluidic devices.

Here we investigate how the local properties of particles in a thermal bath may influence the thermodynamics of the bath, and consequently alter the statistical mechanics of subsystems that comprise the bath. We are guided by the theory of small-system thermodynamics, which is based on two primary postulates: that small systems can be treated self-consistently by coupling them to an ensemble of similarly small systems, and that a large ensemble of small systems forms its own thermodynamic bath. We adapt this “nanothermodynamics” to investigate how a large system may subdivide into an ensemble of smaller subsystems, causing internal heterogeneity across multiple size scales. For the semi-classical ideal gas, maximum entropy favors subdividing a large system of “atoms” into an ensemble of “regions” of variable size. The mechanism of region formation could come from quantum exchange symmetry that makes atoms in each region indistinguishable, while decoherence between regions allows atoms in separate regions to be distinguishable by their distinct locations. Combining regions reduces the total entropy, as expected when distinguishable particles become indistinguishable, and as required by a theorem in quantum mechanics for sub-additive entropy. Combining large volumes of small regions gives the usual entropy of mixing for a semi-classical ideal gas, resolving Gibbs paradox without invoking quantum symmetry for atoms that may be meters apart. Other models presented here are based on Ising-like spins, which are solved analytically in one dimension. Focusing on the bonds between the Ising-like spins we find similarity in the equilibrium properties of a two-state model in the nanocanonical ensemble and a three-state model in the canonical ensemble. Thus, emergent phenomena may alter the thermal behavior of microscopic models, and the correct ensemble is necessary for fully-accurate predictions. Another result using Ising-like spins involves simulations that include a nonlinear correction to Boltzmann’s factor, which mimics the statistics of indistinguishable states by imitating the dynamics of spin exchange on intermediate lengths. These simulations exhibit 1/f-like noise at low frequencies (f), and white noise at higher f, similar to equilibrium thermal fluctuations found in many materials.

In this brief communication, we propose the concept that capillary regression may represent a primary pathogenic process underlying COVID-19 infection, particularly in the serious and life-threatening manifestations of the disease. We suggest that the marked elevations of pro-inflammatory mediators that are observed in these seriously ill patients may directly induce capillary regression and endothelial cell (EC) loss. Recent autopsy studies are demonstrating EC loss leading to widespread microthrombi and associated tissue damage. Recent work has indicated that interleukin-1 beta (IL-1β), tumor necrosis factor-alpha (TNFα), and thrombin, individually and in combination, can potently cause capillary tube regression in experimental models in vitro and in vivo. Other pro-inflammatory mediators including interferon gamma (IFNγ), interleukin-4 (IL-4), and interleukin-13 (IL-13) were also shown to be pro-regressive and could be relevant mediators in COVID-19 patients. Interestingly, combinations of pharmacologic agents were identified that reduced capillary regression and protected capillary tube networks against these pro-inflammatory mediators. Such an approach might be an important therapeutic option going forward to treat key disease states where capillary regression plays a major underlying pathogenic role. Finally, if capillary regression is occurring in response to these pro-inflammatory mediators during COVID-19 infection, we suggest that combinations of blocking agents directed to these key pro-regressive mediators might be necessary to appropriately treat patients.

Background: This retrospective study evaluates the survival effects of metronomic maintenance therapy with fluoropyrimidine in patients with stage III colorectal cancer (CRC) according to epidermal growth factor receptor (EGFR) expression. Methods: We enrolled 197 patients with stage III CRC who had undergone radical resection and FOLFOX regimen adjuvant chemotherapy. The clinicopathological features and effects of metronomic maintenance therapy on survival according to treatment group and EGFR expression were analyzed. By conducting an in vitro cell line study and in vivo study through knockdout of EGFR gene, we analyzed the capacities of cell proliferation and migration. Results: Postoperative relapse and mortality were significantly more common in the FOLFOX group. Metronomic maintenance therapy was a significantly independent predictive factor of postoperative relapse and mortality, as well as a prognostic factor of disease-free survival and overall survival. The significant differences of survival between the two groups were only observed in patients with positive EGFR expression. Conclusions: The present study suggested EGFR expression as the prognostic factor in patients with stage III CRC receiving metronomic maintenance therapy. By analyzing EGFR expression, we can identify the potential candidates with optimal survival benefit from metronomic maintenance therapy in patients with stage III CRC.

Background: The treatment plan of prosthetic restorations supported by dental implants require comprehensive scientific knowledge to deliver prostheses with good prognosis, even before the implant insertion. This review aims to analyze the main prosthetic determinants of the prognosis of implant-supported prostheses. Methods: A systematic review of the literature was conducted with a PICO question: "For partially or complete edentulous subjects treated with implant-supported prostheses, which prosthetic factors could affect clinical outcomes?". A literature search was performed electronically in PubMed (MEDLINE), Scopus and Cochrane Library with the following equation [PROGNOS* OR RISK] FACTOR IMPLANT DENTAL, and by hand search in relevant journals and throughout the selected papers. Results: This revision was carried out based on 50 papers focused on several prosthodontics-related risk factors that were grouped as follows: implant-connection, loading protocol, transmucosal abutments, prosthetic fit, provisionalization, type of retention, impression technique, fabrication technique, and occlusion. More than a half of the studies were systematic reviews (30%), meta-analysis (16%) or prospective evaluations of prosthesis with various kinds of events (18%). But also narrative reviews of literature (14%) and in vitro/animal studies (16%) were found. Conclusions: The current literature provides insufficient evidence for most of the investigated topics. However, based on the accumulated data, it seems reasonable to defend that the best treatment approach is the use of morse taper implants with transmucosal abutments, recorded by means of rigidly splinted copings through the pick-up technique, and screwed by milled prosthesis occlusally adjusted to minimize functional overloading.

The determination of the parameters that characterise the air-void system in hardened concrete elements becomes crucial for structures under freezing and thawing cycles. The ASTM C457 standard describes some procedures to accomplish this task, but they are not easy to apply, require specialised equipment such as a stereoscopic microscope and result in highly tedious tasks to be performed. This paper describes an alternative procedure to the modified point-count method described in the Standard that makes use of macro photography. This alternative procedure is successfully applied to a large set of samples and presents some advantages over the traditional method, since the required equipment is less expensive and provides a more comfortable and less tedious procedure for the operator.

Separation and detection of cells and particles in a suspension are essential for various applications, including biomedical investigations and clinical diagnostics. Microfluidics realizes the miniaturization of analytical devices by controlling the motion of a small volume of fluids in microchannels and microchambers. Accordingly, microfluidic devices have been widely used in particle/ cell manipulation processes. Different microfluidic methods for particle separation include dielectrophoretic, magnetic, optical, acoustic, hydrodynamic, and chemical techniques. Dielectrophoresis (DEP) is a method for manipulating polarizable particles’ trajectories in non-uniform electric fields using unique dielectric characteristics. It provides several advantages for dealing with neutral bioparticles owing to its sensitivity, selectivity, and noninvasive nature. This review provides a detailed study on the signal-based DEP methods that use the applied signal parameters, including frequency, amplitude, phase, and shape for cell/particle separation and manipulation. Rather than employing complex channels or time-consuming fabrication procedures, these methods realize sorting and detecting the cells/particles by modifying the signal parameters while using a simple device. In addition, these methods can significantly impact clinical diagnostics by making low-cost and rapid separation possible.

The comparison of group means in latent variable models plays a vital role in empirical research in the social sciences. The present article discusses extensions of invariance alignment and Haberman linking concerning the choice of linking functions for comparisons of many groups. Robust linking functions are proposed for invariance alignment and robust Haberman linking that are particularly suited to item response data under partial invariance. In a simulation study, it is shown that both linking approaches have comparable performance, and in some conditions, the newly proposed robust Haberman linking outperforms invariance alignment.

Manufacturers of photovoltaic modules do not provide all the information necessary to predict their performance under different climatic conditions. This forces the development of mathematical models of behavior and the application of mathematical methods for the calculation of their associated parameters. A toolbox called PVMSim implemented in MATLAB/GUI is proposed in this paper. PVMSIm provides models allowing the simulation of photovoltaic modules. A two-diode model is used to represent the effect of irradiance and temperature on the V-I and V-P characteristic curves. The accuracy of PVMSim has been vaildated by applying the models to two mono-crystalline and multi-crystalline solar modules of different power ratings and manufacturers. The model PVMSim model accuracy was verified against the manufacturer’s datasheet. This paper shows that this tool is useful for designers and professionals who require an intuitive graphical interface for fast and accurate modeling, simulation and sizing of photovoltaic systems.

Dementia patients express a set of problematic and deteriorating symptoms, along self-care dependency. Overtime, the mental health of family caregivers of persons with dementia may suffer, putting them at a high risk for psychopathology, which may be associated with endangered wellbeing of demented people. This cross-sectional study examined the psychometric properties of the Depression Anxiety Stress Scale 8-items (DASS-8), DASS-12, DASS-21 in a convenient sample of 571 caregivers from northern Italy and southern Switzerland (Mean age = 53, SD = 12, range = 24–89 years). A bifactor structure of the three measures had the best fit; some items of the DASS-12/DASS-21 failed to load on their domain-specific factors. The three-factor structure was invariant across various groups (e.g., gender, education, etc.), expressed adequate reliability and convergent validity, and had strong positive correlation with the 3-item UCLA Loneliness Scale (UCLALS3). Dementia type had no effect on distress scores, which were higher among females, adult children caregivers, those caring for dependent patients, and those who received help with care. For 54.9 and 38.8% of the latter, care was provided by relatives and health professionals, respectively. Since the DASS-8 expresses adequate psychometrics comparable with the DASS-21, it may be used as a brief measure of distress in this population.

Vibrational overtones in deeply bound molecules are sensitive probes for variation of the proton-to-electron mass ratio μ. In nonpolar molecules, these overtones may be driven as two-photon transitions. Here, we present procedures for experiments with O₂⁺, including state-preparation through photoionization, a two-photon probe, and detection. We calculate transition dipole moments between all X²П_g vibrational levels and those of the A²П_u excited electronic state. Using these dipole moments, we calculate two-photon transition rates and AC-Stark-shift systematics for the overtones. We estimate other systematic effects and statistical precision. Two-photon vibrational transitions in O₂⁺ provide multiple routes to improved searches for μ variation.

The dynamics of a spherical particle in an asymmetric serpentine is studied by finite element method (FEM) simulations in a physically unconstrained system. The two-way coupled time dependent solutions illustrate the path of the particle along a curve where a secondary flow (Dean flow) has developed. The simulated conditions were adjusted to match those of an experiment for which particles were focused under inertial focusing conditions. The obtained rotational modes allowed to infer the influence of the local flow around the particle. We propose a new approach to find the decoupled secondary flow contribution employing a quasi-Stokes flow.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

One-dimensional shape memory polymer fibers (SMPFs) have obvious advantages in mechanical properties, dispersion properties and weavability. In this work, a method for fabricating semi-crystallization ethylene-vinyl acetate copolymer (EVA) fiber with two-way shape memory effect by melt spinning and ultraviolet (UV) curing was developed. Here, the effect of crosslink density on its performance was systematically analyzed by gel fraction measurement, tensile tests, DSC and TMA analysis. The results showed that the crosslink density and shape memory properties of EVA fiber could be facilely adjusted by controlling UV curing time. The resulting EVA fiber with cylindrical structure had a diameter of 247.13 ± 10.07 μm, and its mechanical strength and elongation at break were 64.46 MPa and 114.33%, respectively. The critical impact of the crosslink density and applied constant stress on the two-way shape memory effect were analyzed. Moreover, the single EVA fiber could lift more than 143 times its own weight and achieve 9% reversible actuation strain. The reversible actuation capability was significantly enhanced by a simple winding design of the single EVA fiber, which provided great potential applications in smart textiles, flexible actuators and artificial muscles.