Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

Abstract: A biomaterial is proposed for closing extensive bone defects in the maxillofacial region. The composition of the biomaterial includes high-molecular chitosan, chondroitin sulfate, hyaluronate, heparin, alginate and inorganic nanostructured hydroxyapatite. The purpose of the study is to demonstrate morphological and histological early signs of reconstruction of a bone cavity of critical size. The studies were carried out on 84 white female rats weighing 200-250 g. The study group consisted of 84 subjects in total, 40 in the experimental group and 44 in the control group. In all animals, three-walled bone defects measuring 0.5 x 04 x 05 cm were applied subperiosteally in the region of the angle of the lower jaw and filled in experimental group using lyophilized gel mass of chitosan-alginate-hydroxyapatite (CH-SA-HA). In control animals, the bone cavities were filled with an auto-blood clot after bone trepanation and bleeding. The observation periods are 3.5.7 days, 2.3.4.6.8 and 10 weeks. The control of bone regeneration was carried out using multiple morphological and histological analyses. Results showed that following implantation the chitosan construct actively replaced early-stage defects with the formation of a full-fledged new bone tissue as compared to the control group. Already, by the 7th day morphological analysis showed that formation of spongy bone tissue could be seen. After 2 weeks there was a pronounced increase in bone volume (P<0.01), and at 6 weeks after surgical intervention the closure of the defect was 70-80%, after 8 weeks - 100% without violation of bone morphology with a high degree of mineralization. Thus, the use of modified chitosan after filling eliminates bone defects of a critical size in the maxillofacial region, reveals early signs of bone regeneration, and serves as a promising material in reconstructive dentistry.

The study was performed to get the first insight of distribution of the low field volume magnetic susceptibility (MS) throughout the Zagreb city area, based on in-situ field measurements. Most interesting locations were selected for soil sampling and geochemical content was determined using ICP-OES. A geostatistical approach was applied on MS and geochemical results. Median value of 0.245 x 10-3 SI units is proposed to be used as relevant average MS value in Zagreb area. Mean concentrations of heavy metals in Zagreb soils (in µg/g) are: Pb (36.82), Zn (87.77), Cu (30.84), Cd (0.66), Cr (29.04), Co (11.89) and Ni (28.40), being relatively low in comparison with Croatian legislation and with European and world average. Boxplot analyses showed that 45% of studied elements do not show any anomaly, while the rest of elements mostly show only one weak anomaly and they are located at the same sites as MS anomalies. Statistical analysis found significant correlations between MS and following elements: Cd, Co, Fe, Mn, Na, Pb, Sb and Zn. In-situ MS measurements proved to be an efficient tool for initial screening of large areas in terms of elevated heavy elements concentrations, enabling cheap and fast assessment of state of environment.

The current regeneration mode of public space in the old city of Guangzhou is ineffective, thus necessitating supplementation with a more systematic methodology. The “plug-in design” targets sustainable regeneration while preserving the overall urban texture and context, i.e., has little impact on the spatial qualities of the old city. The ultimate goal is to activate the public space of the old city of Guangzhou point-to-area through the insertion of various plug-ins. In this study, the methodology is applied to Xudi Gaodi Street, the core area of the old city of Guangzhou, to explore its effects on sustainability. The internal public space is isolated and supplied with rigid and flexible plug-ins from multiple dimensions, which not only improves the spatial environment but also injects new urban formats. This work provides a specific solution for regeneration in Guangzhou’s old city while enhancing empirical knowledge of the plug-in design to support urban regeneration theory and further practical development.

Remote sensing (RS) technology has significantly contributed to geological exploration and mineral resource assessment. However, its effective application in vegetated areas encounters various challenges. This paper aims to provide a comprehensive overview of the challenges and opportunities associated with RS-based lithological identification in vegetated regions. The article begins by introducing the sources and processing methods of RS data, which serve as the foundation for subsequent analysis. Moreover, it highlights the techniques and methodologies employed for lithological classification in vegetated areas. Notably, hyperspectral RS and Synthetic Aperture Radar (SAR) have emerged as prominent tools in lithological identification. In addition, this paper addresses the limitations inherent in RS technology, including issues related to vegetation cover and terrain effects, which significantly impact accurate lithological mapping. To propel further advancements in the field, the paper proposes promising avenues for future research and development. These include the integration of multi-source data to enhance classification accuracy and the exploration of novel RS technologies and algorithms. In summary, this paper presents valuable insights and recommendations for advancing the study of RS-based lithological identification in vegetated areas.

The merge areas of freeway work zones include relatively significant safety hazards that have continuously led to urgent safety issues to be solved by the management departments. In order to make up for the cumbersome process of independent identification of rear-end collision and lane change collision on complex road sections, an appropriate identification method of traffic conflicts in the merge area of freeway work zone was explored, this study collected vehicle running tracking data from the merge areas of multiple work zones, using an unmanned aerial vehicle video technique. Based on an inter-frame difference method and the principle of a spatio-temporal context visual tracking algorithm, the vehicles were detected and tracked, and the coordinate data of the vehicles in continuous motion were parsed using MATLAB extension tools. Based on the behavior characteristics of vehicle conflict avoidance, a new identification method for evading severe traffic conflicts is proposed according to the initial velocity, acceleration and accident rate of section traffic. Then, a statistical analysis was performed on the spatial distribution characteristics of the traffic conflicts in typical merge areas. The impacts of the road conditions in work zones, vehicle factors, and traffic flow factors on the traffic conflicts were analyzed. A binomial logistic model was established to identify the main influencing factors. The results show that in the merge area of the freeway work zone, there are serious traffic conflicts between vehicles in the following two situations: (Ⅰ) v∈[7,13.5] m/s and a∈[-3.96,-0.65]m/s2; and (Ⅱ) v∈[13.5,24.3] m/s, and a∈[-3.96,-1.57] m/s2. The probabilities of serious traffic conflicts in the first and last 25 m of the merge area are greater than those in the other sections. The smaller the space between the upstream work zone and the merge area, the greater the probability of serious traffic conflicts between vehicles. When the average vehicle speed is relatively high, the probability of serious conflicts is the highest, i.e., by a multiple of 5.95 from the baseline. Moreover, the probability of serious conflicts between vehicles is higher for larger vehicles, i.e., 4.765 times that for small vehicles. The research results can serve as a reference for freeway management departments to improve the safety levels of merge areas during road work. For example, the probability of serious conflicts can be effectively reduced by setting up reasonable speed limit signs in the work zone, increasing the spacing between work zone and merge area, and appropriately diverting large vehicles.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

From the standpoint of Neoliberal Institutionalism, this study explores Malaysia's participation in activities that make energy the topic and/or object of foreign policies, whether through bilateral or multilateral engagements. This research, which aims to evaluate the relevance of energy in Malaysia's economy and diplomacy and to explain Malaysia's reason for its involvement in these cooperations, is necessary because of Malaysia's growing involvement in the global energy market. Information for this study was gathered from a variety of government sources, interviews, published statistical data, and previous studies. The study demonstrates how vital energy is to Malaysia's economy. The Lao PDR-Thailand-Malaysia-Singapore Power Integration Project (LTMS-PIP) initiative, in which Malaysia is participating, is evidence of the viability of multilateral power commerce in the area. The Peninsula Gas Utilisation (PGU) pipeline in Peninsular Malaysia and the Four-Fuel Diversification Policy 1981 (4FDP 1981), which increases natural gas utilisation, are related to Malaysia's participation in the Malaysia-Thailand Joint Development Area (MT-JDA). Malaysia would want to think about streamlining its energy administration.

In past years, lithium-ion batteries (LIBs) can be found in every aspect of life, and batteries, as energy storage systems (ESSs), need to offer electric vehicles (EVs) more competition to be accepted in markets for automobiles. Thick electrode design could reduce the use of non-active materials in batteries that its energy density would be improved and its cost would be cut. However, thick electrodes are limited by their weak mechanical stability and poor electrochemical performance, these limitations could be classified as the critical cracking thickness (CCT) and the limited penetration depth (LPD). The understanding of the CCT and the LPD have been proposed and the recent works on breaking the CCT and improving the LPD are listed in this article. By comprising these attempts, some thick electrodes could not offer higher mass loading or higher accessible areal capacity that would defeat the purpose.

Impervious surface area (ISA) is a crucial indicator for quantitative urban studies. It is also important for land use land cover classification, groundwater recharge, sustainable development, urban heat island effects, and more. Spectral ISA mapping suffers from mixed pixel problems, especially with bare soil. This study aims to develop an ISA index for spatiotemporal urban mapping from common multispectral bands by reducing soil signature better than in previous studies. This study proposed a global impervious surface area index (GISAI) enhancing ISA mapping accuracy using a temporal parameter of the remote sensing (RS) dataset. Bare soil spectral reflectance shows more fluctuation than urban ISA. Therefore, the study uses minimum composites of earlier urban indices to compile minimum soil signature. It is later improved by removing water, increasing the contrast between bare soil and urban ISA and reducing bright bare soil area. This study maps the ISA of all 12 megacities using the annual RS image collection from 2021. GISAI reduced the bare soil signature and achieved an overall accuracy of 87.29%, F1-score of 0.84, and Kappa coefficient of 0.75. However, it has some limitations with grey bare soil and barren hilly areas. By limiting bare soil signature, GISAI broadens the scope of inter-urban studies globally and lengthens potential urban time-series analysis using common multispectral bands.

Conventional methods of crop mapping need ground truth information to train the classifier. Thanks to the frequent acquisition allowed by recent satellite missions (Sentinel 2), we can identify temporal patterns that depend on both phenology and crop management. Some of these patterns are specific to a given crop and thus can be used to map it. Thus, we can substitute ground truth information used in conventional methods with agronomic knowledge. This approach was applied to identify irrigated permanent grasslands (IPG) in the Crau area (Southern France) which play a crucial role in groundwater recharge. The grassland is managed by making three mows during the May-October period which leads to a specific temporal pattern of leaf area index (LAI). The mowing detection algorithm was designed using the temporal LAI signal derived from Sentinel 2 observations. The algorithm includes some filtering to remove noise in the signal that might lead to false mowing detection. A pixel is considered a grassland if the number of detected mows is greater than 1. A data set covering five years (2016-2020) was used. The detection mowing number was done at the pixel level and then results are aggregated at the plot level. A validation data set including 780 plots was used to assess the performances of the classification. We obtained a Kappa index ranging between 0.94-0.99 according to the year. These results were better than other supervised classification methods that include training data sets. The analysis of land-use changes shows that misclassified plots concern grasslands managed less intensively with strong intra-parcel heterogeneity due to irrigation defects or year-round grazing. Time series analysis, therefore, allows us to understand different management practices. Real land-use change in use can be observed, but long time series are needed to confirm the change and remove ambiguities with heterogeneous grasslands.

A healthy park-people relation depends essentially on the fair and sustainable maintenance of rural livelihood. When protected area is designated, rural people may face restrictions of access to land and resource use for multiple ecosystem services. In Wuyishan of China, we analysed the role of traditional tea cultivation during consistent protected area management to find ways to maintain stability of this social-ecological system in the new national park era. We used an intensive social survey to investigate tea’s role, perception of ecosystem services and impacts on tea cultivation from consistent conservation policies. Results showed that tea cultivation brought major household income and associated with multiple culture services. Protected area management affected land use and conservation outcomes were more obvious to farmers than economic and social ones. From the perspective of a social-ecological system, tea cultivation in national should be conservation-compatible activities from which the potentially lost economic value is remedied by ecological and cultural valorisation. To sustain the resilience of the social-ecological system, we proposed a three-scale management framework to regulate biophysical elements at land plot scale, to link production and market at the mountain level, and to secure tenure and encourage community participation at the landscape level.

Smart Internet of Vehicles (IoVs) combined with Artificial Intelligence (AI) will contribute to vehicle decision-making in the Intelligent Transportation System (ITS). Multi-Vehicle Pursuit games (MVP), a multi-vehicle cooperative ability to capture mobile targets, is becoming a hot research topic gradually. Although there are some achievements in the field of MVP in the open space environment, the urban area brings complicated road structures and restricted moving spaces as challenges to the resolution of MVP games. We define an Observation-constrained MVP (OMVP) problem in this paper and propose a Transformer-based Time and Team Reinforcement Learning scheme (T3OMVP) to address the problem. First, a new multi-vehicle pursuit model is constructed based on decentralized partially observed Markov decision processes (Dec-POMDP) to instantiate this problem. Second, by introducing and modifying the transformer-based observation sequence, QMIX is redefined to adapt to the complicated road structure, restricted moving spaces and constrained observations, so as to control vehicles to pursue the target combining the vehicle’s observations. Third, a multi-intersection urban environment is built to verify the proposed scheme. Extensive experimental results demonstrate that the proposed T3OMVP scheme achieves significant improvements relative to state-of-the-art QMIX approaches by 9.66%~106.25%. Code is available at https://github.com/pipihaiziguai/T3OMVP.

Mahanadi is one of the major inter-state east flowing perennial rivers in peninsular India. Hamp watershed of Seonath Sub-basin of upper Mahanadi basin was considered for the study to estimate the sediment yield and nutrient loss-based identification of critical agricultural sub-watershed and its critical Hydrological Response Unit (HRU) using Soil and Water Assessment Tool (SWAT) in-terfaced with GIS i.e., ArcSWAT. The study area was divided into 14 sub-watersheds considering topographical parameters derived from DEM and drainage network. The land cover, soil layers, and DEM were used to generate 207 HRUs for analysis of annual runoff, sediment yield and nu-trient loss for 2004-2008 (calibration period) and 2010-2013 (validation period). The sediment yield, runoff estimation and nutrient loss matched consistently well with the monthly and seasonal measured values. On the basis of average annual sediment yield (18.18 t/ha), runoff (245.97 mm) and nutrient loss NO3-N (1.62 kg/ha), respectively, sub-watershed WS4 was categorized under high priority for critical are identification. The sub watershed WS4 comprises of 15 HRUs (No. 36 - 50) with four kharif crops viz rice, soybean, maize and sugarcane. Results showed that the crops soy-bean, maize and sugarcane reduced the average annual runoff by 18.1, 31.4 and 18.0 per cent, respectively whereas the sediment yield was increased drastically by 104.5, 37.5 and 5.7 per cent, respectively as compared to rice. Soybean and maize crops HRU generate significant amount of soil and nutrient loss and were found to be as the critical HRUs for the upper Mahanadi River basin

With the development of the city, a large number of water networks in the built-up areas of Bangkok have been filled and hardened, resulting in poor urban flooding and aggravating flooding, causing loss of life and property of citizens. In this paper, on the basis of combing the current water networks and open space potential flood storage points in the built-up areas of Bangkok, the complex network diagram of the water system in the built-up areas of Bangkok is constructed by combining the theory of complex networks and analyzing the attribute parameters of the network and the characteristic parameters of the open space storage nodes and water system paths, and finding that the water system network in the built-up area of Bangkok has complex network characteristics such as robustness, clustering and hierarchy. By exploring the key storage points and water system connection paths, the researchers initially constructed a flood safety pattern in the built-up area of Bangkok with 145 key nodes and 127 river paths as the backbone, and conceptualized the development study of the flood safety pattern in both horizontal and vertical directions. The urban flood safety pattern based on complex network theory proposed in this paper provides a case reference and methodological ideas to scientifically solve the game conflict between the demand for construction land for urban development and the construction area of urban open space storage points and water storage network under the increasingly severe flooding situation.

Public green and open spaces fulfil various social, ecological, economic, and aesthetic roles, which complement each another, but can also compete with one another. COVID-19 pandemic catalysed multiple societal changes, including citizens’ perception, needs and expectations posed towards urban green spaces. This article discusses the extent to which the temporally and geographically changed patterns of experiencing these natural spaces also influenced users’ perception and behaviour as well as their appreciation of the conservation areas. The study is based upon two surveys carried out in the greater metropolitan region of Vienna, the capital city of Austria. A quantitative survey (representative online panel) among Viennese population (n=1012), as well as qualitive interviews with experts responsible for conservation areas, administrators of federal parks, along with NGOs representatives were carried out in spring and summer 2021. Our study shows the changed use of urban and suburban large green spaces and conservation areas: first, from the perspective of those responsible for the areas as well as the visitors. Both perspectives supplement one another. They highlight also changed perception of urban citizens towards green spaces during COVID-19 pandemic. An increased importance of time spent in nature (68%) and possibility to visit large green areas (67%) was reported by Viennese citizens. Also, higher recognition of green spaces located close to home was observed among 69% of the respondents. Thus, the presented study contributes to the ongoing international discussion on the transition of societal needs and its effects on urban green spaces induced by the pandemic. Presented results deliver solid arguments highlighting the need of urgent transformation towards a more sustainable, resilient and healthy urban space.

The relative operating characteristic (ROC) curve is a popular diagnostic tool in forecast verification, with the area under the ROC curve (AUC) used as a verification metric measuring the discrimination ability of a forecast. Along with calibration, discrimination is deemed as a fundamental probabilistic forecast attribute. In particular, in ensemble forecast verification, AUC provides a basis for the comparison of potential predictive skill of competing forecasts. While this approach is straightforward when dealing with forecasts of common events (e.g. probability of precipitation), the AUC interpretation can turn out to be oversimplistic or misleading when focusing on rare events (e.g. precipitation exceeding some warning criterion). How should we interpret AUC of ensemble forecasts when focusing on rare events? How can changes in the way probability forecasts are derived from the ensemble forecast affect AUC results? How can we detect a genuine improvement in terms of predictive skill? Based on verification experiments, a critical eye is cast on the AUC interpretation to answer these questions. As well as the traditional trapezoidal approximation and the well-known bi-normal fitting model, we discuss a new approach which embraces the concept of imprecise probabilities and relies on the subdivision of the lowest ensemble probability category.

Disease-related data and information collected by physicians, patients, and researchers seem insignificant at first glance. Still, the same unorganized data contain valuable information that is often hidden. The task of data mining techniques is to extract patterns to classify the data accurately. One of the various Data mining and its methods have been used often to diagnose various diseases. In this study, a machine learning (ML) technique based on distributed computing in the Apache Spark computing space is used to diagnose diabetics or hidden pattern of the illness to detect the disease using a large dataset in real-time. Implementation results of three ML techniques of Decision Tree (DT) technique or Random Forest (RF) or Support Vector Machine (SVM) in the Apache Spark computing environment using the Scala programming language and WEKA show that RF is more efficient and faster to diagnose diabetes in big data.

For public safety and physical security, currently more than a billion closed-circuit television (CCTV) cameras are deployed around the world. Proliferation of artificial intelligence (AI) and machine learning (ML) technologies has gained significant applications including crowd surveillance. The state-of-the-art distance and area estimation algorithms either need multiple cameras or a reference scale as a ground truth. It is an open question to obtain an estimation using a single camera without a scale reference. In this paper, we propose a novel solution called E-SEC, which estimates interpersonal distance between a pair of dynamic human objects, area occupied by a dynamic crowd, and density using a single edge camera. The E-SEC framework comprises edge CCTV cameras responsible for capture a crowd on video frames leveraging a customized YOLOv3 model for human detection. E-SEC contributes an interpersonal distance estimation algorithm vital for monitoring the social distancing of a crowd, and an area estimation algorithm for dynamically determining an area occupied by a crowd with changing size and position. A unified output module generates the crowd size, interpersonal distances, social distancing violations, area, and density per every frame. Experimental results validate the accuracy and efficiency of E-SEC with a range of different video datasets.

The study of the area model of Pinus tabulaeformis forest provides an important reference for improving the management of Pinus tabulaeformis and revealing the growth law of Pinus tabulaeformis. According to the classification method proposed by Munro, stand growth and harvest prediction models are divided into three categories: full stand model, single wood model and diameter distribution model. Based on the fixed sample data of Shangluo Pinus tabulaeformis, the spatial instead of time method is used to process the data, and the weight coefficient of each model in the combined prediction model is calculated by using the optimal weighting method. The single wood model, the whole forest model and the diameter distribution model are combined by the combined prediction method to integrate the fault area prediction of Pinus tabulaeformis forest. The results show that the combined prediction method is more accurate than the single model (single wood model, whole forest model and diameter distribution model). At the same time, the method can improve the compatibility of the forest break area prediction model, ensure the consistency of the forest break area prediction, and provide a new direction for the research of forest resource monitoring and investigation.

Research shows that stress, a common problem in dense cities, can be relieved in the natural environment. As great significance has been attached to the urban environment and public health in the society, this paper aims to study the relation and interaction between the perceived sensory dimension of urban park green space, attention restoration and state empathy. Therefore, we conducted an on-site questionnaire survey in four typical parks in Chengdu in terms of age, sex, daily stress, frequency of access in parks and other basic information of the respondents. The main part consists of perceived dimension, state empathy and attention restoration. The software SPSS24.0 is applied to the test of the validity and reliability of the PSD Scale, and then the important correlation between the perceived sensory dimensions in the parks and visitors' attention restoration is analyzed through multiple linear regression. Finally, the moderation effect of state empathy is tested by PROCESS. The findings show that (1) only seven dimensions in the PSD Scale are effective; (2) Serene and Refuge in the perceived sensory dimensions have significant effect on the restorative components of attention. (3) Except the dimensions of Rich in Species and Refuge, empathy enhanced the moderation effect in the interaction between the other five dimensions the Perceived Restorative Scale(PRS), especially in the interaction between the dimension Social and PRS. However, this study needs to be further explored to provide scientific basis and design strategy guidance for the research on the restoration potential of urban park green space in high-density urban areas.

The coronavirus disease (COVID-19) pandemic is rapidly spreading across the world. In Democratic Republic of Congo (DRC), 11 out of 26 provinces have been affected on 19 June 2020. The purpose of this study was to assess the public views, attitudes and beliefs related to the COVID-19 pandemic among the population of an unaffected city.Methods: This is a descriptive observational study conducted in an unaffected city using a questionnaire. Findings: A total of 769 people participated. The average age was 36 ±14 years. The sex ratio (male: female) was 1.6. The majority of respondents (97%) is aware of the existence of the COVID-19 pandemic, it is well informed about the signs of the disease, its severity and barrier measures, however few of them have adopted the change in habit and behavior in respect of the barrier measures. Lack of water for handwashing is the most common difficulty in complying with barrier measures (71%). The COVID-19 is considered as an artificial virus designed to reduce the world population by 26%, God’s punishment (22%). Only 36% of the participants are in favor of vaccination against COVID-19. Vaccine is, a western conspiracy to spread COVID-19 in Africa (38%), testing it on Africans (35%), sterilize Africans’ people (12%).Conclusions: Cities not yet affected by COVID-19 in DRC are aware of the existence of the disease, but insufficiently prepared to deal with it. It is important to increase awareness on barrier measures, combating false information, and improving regular water supply for regular handwashing.

Introduction: Oral health knowledge, beliefs and attitudes of parents have a direct influence on their child’s oral health maintenance, dietary habits and encourage healthy behaviors. The aim of this study was to assess the knowledge, and attitude of parents with regards to the oral health practice of their children and its associated factors. Methods: A self -administered structured questionnaire was administered to parents or guardians of learners aged 5 to 12 years at a low socio-economic rural primary school in the uGu district, KwaZulu Natal, South Africa to collect demographic variables, knowledge of dental health, use of toothbrush, use of toothpaste, dietary practices and dental visits; practice with respect to dental care and attitudes towards oral health. The questionnaire was translated from English to IsiZulu was used. Bivariate and multivariate logistic regressions were used to assess the association between parent’s sociodemographic factors with their oral health knowledge and practice scores. Results: One hundred and forty four completed survey instruments were received with an eighty percent (118) representation of mothers. Ninety five percent of the parents (136) had a positive attitude towards oral health with 86% (124) of the children brushed their tongue and 89% (128) of the children brushed their teeth happily. The mean knowledge score was 70% with a median of 72%. Children were significantly more likely to brush their tongues (AOR: 3.20 95% CI: 1.06-9.66) and were more likely to be happier when brushing their teeth (AOR: 4.65 95% CI: 1.41-15.38) when the caregivers were their mothers, and when parents had an above average knowledge score (AOR: 1.86 95% CI: 0.72-4.85) and had positive attitudes (AOR: 3.20 95%CI: 0.46-22.00). Conclusion: To reduce the gaps in knowledge, oral health promotion should be integrated into all point of care contact with parents at health facilities, increased community awareness and advertising campaigns as well as a more focused school health oral program that addresses primary prevention, screening and appropriate referrals to health facilities

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

Cocoa is an important commodity crop not only to produce one of the most complex products such as chocolate from the sensory perspective, but one that commonly grows in developing countries close to the tropics. This paper presents novel techniques applied using cover photography and a novel computer application (VitiCanopy) to assess the canopy architecture of cocoa trees in a commercial plantation in Queensland, Australia. From the cocoa trees monitored, pod samples were collected, fermented, dried and grinded to obtain the aroma profile per tree using gas chromatography. The canopy architecture data were used as inputs in an artificial neural network (ANN) algorithm and the aroma profile considering six main aromas as targets. The ANN model rendered high accuracy (R = 0.82; MSE = 0.09) with no overfitting. The model was then applied to a satellite image from the whole cocoa field studied to produce canopy vigor and aroma profile maps up to the tree-by-tree scale. The tool developed could aid significantly the canopy management practices in cocoa trees that have a direct effect on cocoa quality.

A risk of ischemic stroke increases exponentially after menopause. Even a mild-ischemic stroke can result in increased frailty. Frailty is a state of increased vulnerability to adverse outcomes, which subsequently increases risk of cerebrovascular events and severe cognitive decline, particularly after menopause. Several interventions to reduce frailty and subsequent risk of stroke and cognitive decline have been proposed in laboratory animals and patients. One of them is whole body vibration (WBV). WBV recuperates cerebral function and cognitive ability that deteriorates with increased frailty. The goal of the current study is to test the efficacy of WBV in reducing post-ischemic stroke frailty and brain damage in reproductively senescent female rats. Reproductively senescent Sprague–Dawley female rats were exposed to transient middle cerebral artery occlusion (tMCAO) and randomly assigned to either WBV or control groups. Animals placed in the WBV group underwent 30 days of WBV (40 Hz) treatment performed twice daily for 15 min each session, 5 days each week. The motor functions of animals belonging to both groups were tested intermittently and at the end of treatment period. Brains were then harvested for inflammatory markers and histopathological analysis. The results demonstrate a significant reduction in inflammatory markers and infarct volume with significant increases in brain-derived neurotrophic factor and improvement in functional activity after tMCAO in middle-aged female rats that were treated with WBV as compared to the control group. Our results may facilitate a faster translation of the WBV intervention for improved outcome after stroke, particularly among frail women.

This paper considers the problem of quantifying the quality of a model selection problem for a graphical model. The model selection problem often uses a distance measure such as the Kulback-Leibler (KL) distance to quantify the quality of the approximation between the original distribution and the model distribution. We extend this work by formulating the problem as a detection problem between the original distribution and the model distribution. In particular, we focus on the covariance selection problem by Dempster, [1], and consider the cases where the distributions are Gaussian distributions. Previous work showed that if the approximation model is a tree, that the optimal tree that minimizes the KL divergence can be found by using the Chow-Liu algorithm [2]. While the algorithm minimizes the KL divergence it does not minimize other measures such as other divergences and the area under the curve (AUC). These measures all depend on the eigenvalues of the correlation approximation measure (CAM). We find expressions for KL divergence, log-likelihood ratio, and AUC as a function of the CAM. Easily computable upper and lower bounds are also found for the AUC. The paper concludes by computing these measures for real and synthetic simulation data.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

Tandem mass spectrometry (MS/MS) for diagnosing inborn errors of metabolism (IEM) is recognized as an ethical, safe, simple, and reliable screening test. Presented bibliometric analysis aims to describe the network structure of the scientific community in the study area at the level of countries, institutions, authors, papers, keywords, and sources; scientific productivity, directions, and collaboration efforts in a considered period (1991–2023.) Using the PRISMA method, we conducted a systematic search for articles reporting using MS/MS to screen for inherited metabolic disorders and inborn errors of metabolism collected from the Web of Science Core Collection (WOSCC.) A total of 451 articles out of 546, by 2,682 authors, published in 190 journals, with 15,440 citations in 8,181 citing articles, with an average citation of 34.24 per article, and an H-index of 64 were retrieved from the WOSCC. The research status of MS/MS in IEM screening was identified. The most relevant current research directions and future areas of interest were revealed: "selective screening for IEM," "new treatments for IEM," "new disorders considered for MS/MS testing," "ethical issues associated with newborn screening," "new technologies that may be used for newborn screening," "use of a combination of MS/MS and gene sequencing," etc.

The recovery of precious metals is a project with both economic and environmental significance. In this paper, it presents how to use bacterial mineralization to selectively recover gold from multi-ionic aqueous systems. The Bacillus licheniformis FZUL-63, separated from a landscape lake in FuZhou University, was shown to selectively mineralize and precipitate gold from coexisting ions in aqueous solution. The removal of Au(III) was almost happened in first hour, and FTIR data show that the amino, carboxyl and phosphate groups on the surface of the bacteria are related to the adsorption of gold ions. XPS results implied that Au(III) ions are reduced to monovalent, and then the Au(I) was adsorbed on the bacterial surface at the beginning stage(first hour). XRD results showed the gold biomineralization began about 10 hours after the interaction between Au(III) ions and bacteria. The Au(III) mineralization has been rarely influenced by other co-existing metal ions. TEM analysis shows the gold nanoparticles are polyhedral structure with a particle size of ~20 nm. The Bacillus licheniformis FZUL-63 could selectively mineralize and recover 478 mg/g(dry biomass) gold from aqua regia-based metal wastewater through four cycles. It could be of great potential in the practical application.

Within an Internet of Multimedia Things, the risk of disclosing streamed video content, such as arising from video surveillance, is of heightened concern. This leads to the encryption of that content. To reduce the overhead and lack of flexibility arising from full encryption of the content, a good number of selective-encryption algorithms have been proposed in the last decade. Some of them have limitations, in terms of significant delay due to computational cost, or excess memory utilization, or, despite being energy efficient, do not provide a satisfactory level of confidentiality, due to their simplicity. To address such issues, this paper presents a lightweight selective encryption scheme, in which encoder syntax elements are encrypted with the innovative EXPer (EXtended Permutation with exclusive OR). The selected syntax elements are taken from the final stage of video encoding that is during entropy coding. As a diagnostic tool, the Encryption Space Ratio measures encoding complexity of the video relative to the level of encryption so as to judge the success of the encryption process, according to entropy coder. A detailed comparative analysis of EXPer with state-of-the-art algorithms confirms that the EXPer provides significant confidentiality with a small computational cost and negligible encryption bitrate overhead. Thus, the results demonstrate that the proposed security scheme is a suitable choice for constrained devices in an Internet of Multimedia Things environment.

Additive manufacturing (AM) offers customization of microstructure and mechanical properties of fabricated components according to the material selected, and process parameters applied. Selective laser melting (SLM) is the commonly used technique for processing high strength aluminum alloys. Selection of SLM process parameters could control the microstructure of parts and their mechanical properties. However, the process parameters limit and defects obtained inside the as-built parts present obstacles to customized part production. This study investigates the influence of SLM process parameters on the quality of as-built Al6061 and AlSi10Mg parts according to the mutual connection between the microstructure characteristics and mechanical properties. The microstructure of both materials was characterized for different parts processed over a wide range of SLM process parameters. The optimized SLM parameters were investigated to eliminate the internal microstructure defects. The behaviour of mechanical properties of parts was presented through regression models generated from the design of experiment (DOE) analysis for the results of hardness, ultimate tensile strength, and yield strength. A comparison between the results obtained and that reported in the literature is presented to illustrate the influence of process parameters, build environment, and powder characteristics on the quality of parts produced. The results obtained from this study could help to customize the part’s quality by satisfying their design requirements in addition to reducing the as-built defects which in turn reduce the amount of the post-processing needed.

Soil water content (SWC) and soil organic carbon (SOC) are two important factors to consider when revegetation in degraded land of arid and semiarid areas. Knowing the response of SWC and SOC to vegetation restoration as well as their coupling interaction is important for sustainability of vegetation restoration. In this study, three common plantations of the same recovery years were selected on China’s Loess Plateau, which included Pinus sylvestris, Pinus tabuliformis and Populus simonii, to evaluate the response of SWC and SOC to vegetation restoration as well as their interactions, and then revealed the influencing factors of SWC and SOC variations. Results showed that compared to the grassland, three plantations all exacerbated the deficit of deep soil water, but Populus simonii increased the SOC, while the rest all decreased the SOC. And tradeoff of Populus simonii had the lowest root mean squared error (RMSD). Therefore, Populus simonii was identified as representing a suitable revegetation technique for this region. There was strong interaction between SWC and SOC for shallow soil layers. Land use type (LUT) has an important effect on deep SOC variations, while SOC and soil texture for deep SWC variations. The results were helpful to the sustainable development of artificial forests in this region as well as other similar arid and semiarid areas.

The integration of nature-based solutions into land use optimization has emerged as a focal point of current research, primarily due to its efficacy in mitigating flooding impacts and fostering sus-tainable development in both urban and rural areas. Utilizing Shanghai Pujiang Country Park as a case study, this paper conducts a simulation analysis to assess the flood mitigation effectiveness of three distinct land use patterns (Natural scenario, Scenario N; Complete urbanization scenario, Scenario U; Country Park Planning scenario, Scenario P) under five stormwater scenarios with re-turn periods of 2, 5, 10, 20, and 50 years. The findings reveal that Scenario P exhibits superior flood mitigation performance, particularly under stormwater scenarios with a return period of less than 50 years. Building upon these results, the paper proposes recommendations for optimizing land use with a focus on mitigating the impact of flooding. This study is crucial for comprehending the mechanisms involved in urban stormwater logging mitigation through land use methods and holds significance for decision-making in land use and planning at the micro level.

Water area segmentation in remote sensing is of great importance for flood monitoring. To overcome some challenges in this task, we construct the Water Index and Polarization Information (WIPI) multi-modality dataset and propose a multi-Modality Fusion and Gated multi-Filter U-Net (MFGF-UNet) convolutional neural network. The WIPI dataset enhances the water information and reduces the data dimension. In particular, the Cloud-Free label provided in the database effectively mitigates the issue of scarcity of labeled samples Since a single form or uniform kernel size cannot handle the variety in size and shape of water bodies, we proposed the gated multi-filter inception (GMF-Inception) module in our MFGF-UNet. Moreover, we utilize the attention mechanism by introducing the Gated Channel Transform (GCT) skip connection and integrating GCT into GMF- Inception to further improve model performance. Extensive experiments on three benchmarks, including WIPI, Chengdu and GF2020 datasets demonstrate that our method achieves favorable performance with lower complexity and better robustness against six competing approaches. For example, on WIPI, Chengdu and GF2020 datasets, the proposed MFGF-UNet model achieves F1 of 0.9191, 0.7410, and 0.8421, respectively, which average F1 on three datasets is 0.0045 higher than the U-Net model and reduces 62% average GFLOPs. New WIPI dataset, code and trained models have been released on GitHub

Understanding the evolving hydrological characteristics of landslide-induced barrier lakes is crucial for flood control, forecasting, early warning, and safety measures in the reservoir area. This study examines the changes in hydrological characteristics of the Attabad landslide-dammed lake over the past decade after the occurrence of the landslide, focusing on lake area dynamics and sediment concentration. High-resolution satellite images from QuickBird, Pleiades, and WorldView2 over seven periods were analyzed. The findings indicate that the lake area has gradually decreased, with the center of mass shifting towards the lake dam, indicating a trend towards stability. The suspended sediment in the barrier lake is distributed in a strip running from north to south, then northeast to southwest, with sediment concentration decreasing from the lake entrance to the dam and from the lake bank to the center. Over time, the average sediment concentration has decreased from 2010 to 2020, with higher concentrations in summer than in winter. Notably, during the 2017-2020 period, the lower-middle parts of the lake experienced higher sediment concentration, while the dam area witnessed lower concentrations, thereby reducing the sediment impact on the dam.

Based on the analysis of the spatial distribution of uranium grade in 348 boreholes of a uranium deposit in Xinjiang, the enrichment and spatial variation of uranium ore in two stopes of the deposit are discussed by using multifractal theory. The distribution characteristics of uranium ore of the two stopes are studied by multifractal parameters: the scaling exponent of mass , the scaling exponent of each sub-set and its corresponding fractal dimension , the fractal dimension D0 and information dimension D1. The differences of uranium distribution in two stopes can be well quantified by multifractal spectrum and multifractal parameters( , , ).10m×10m is defined as a fence unit, and the window sizes are respectively set, the singularity exponent of the two stopes are calculated by this element concentration-area(C-A) method. The results show that the multifractal theory and model can organically combine spatial structure information, scale change information and anisotropy information to obtain low-grade and weak mineral resources information, and can effectively distinguish complex and superimposed anomalies. This will provide a basis for local concentration and spatial variation rules of uranium distribution and the design of the parameters of leaching uranium mining well site.

This paper reports modelling outcomes for improvements to building energy performance in Indonesia. Long-term climate effects due to building energy demands including carbon emissions are also considered. The global change assessment model (GCAM) was used to generate the related end-user building energy data, including socioeconomics for urban areas of Indonesia. As a comprehensive study, the total life cycle of carbon in the building sector and the concept of zero-carbon buildings, including energy efficiency, zero-emissions electricity and fuel switching options were considered. Building shell conductance (u-value) of building envelope, floor area ratio (FAR), air conditioner (AC) efficiency, electrical appliances (APLs) efficiency, rooftop photovoltaic (PV) performance and ground source heat pump (GSHP) systems were considered as parameters to mitigate carbon emissions under the operational energy category in GCAM. Carbon mitigation associated with the cement production process was considered in the raw material category. Urban population and labour productivity in Indonesia were used as base inputs with projected growth rates to 2050 determined from available literature. Low growth rate ‘LowRate’ and high growth rate ‘HighRate’ were considered as variable inputs for u-value, FAR, AC efficiency, APLs efficiency, and PV capacity factor to model emissions mitigation. The energy consumption of the GSHP was compared to the conventional reverse cycle ACs to identify the potential of the GSHP as a fuel-switching option. Only base input data were used for cement production process parameters without applying any variable inputs. GCAM base scenarios based on input data only (without modifying variable data) for the residential building sector in Indonesia were considered the benchmark for this study. Total potential carbon emissions mitigation was found to be 432 Mt CO2-e for the residential building sector in Indonesia over 2020-2050. It was found that an average of 24% carbon emissions mitigation could be achieved by 2020-30 and 76% in 2031-2050.

In recent years, the emergence of spatiotemporal big data has made the transition of functional identification from the physical dimension to socioeconomic or human activities becoming more common. In the identification of urban functional areas, most studies considered only a single data source and a single division scale, the research results have problems such as low update frequency or incomplete information in a single data set, and overfitting or underfitting in a single spatial resolution. Using taxi trajectory data and point of interest (POI) data as the main data source, this study proposes a multi-scale recursive identification method for urban functional areas based on cross-validation. First, used the dynamic time warping (DTW) algorithm generates a time series similarity matrix, the CA-RFM model combines the clustering algorithm and random forest model is constructed, the model uses a clustering algorithm (K-MEDOIDS) to extract sig-nificant feature regions as input, which are imported into the random forest model for UFZ identification. Then, to overcome the shortcomings of single scale in expressing urban structural characteristics, a recursive model of different levels of urban road networks is established to classify multi-scale functional areas. Finally, cross-validation using the CA-RFM model and POI quantitative identification method, obtains the final identification results of urban functional areas. This paper selects Shenzhen as the study area for the case study, the results show that the com-bination of clustering algorithm and random forest model greatly reduces the error of manual selection of training samples. In addition, the research shows the superiority of the multi-scale recursive identification method that fuses multi-source data and performs cross-validation from two aspects, that is, the division speed of urban functional area identification results is accelerated and the accuracy is improved.

This study aims to determine the present and future scopes of the digital economy in Bangladesh to build a developed and prosperous country by 2041. Simultaneously, it analyses the components of the Digital Economy from numerous perspectives from contributing to Bangladeshi economy with an adaptation of the 4th Industrial Revolution and emerging technologies. In the methodology section, qualitative approach is conducted to determine the research objectives where secondary data is used. Around 100 papers are collected and 51 articles are used for conducting this study. The findings of the study are to present the current state of the digital economy which is developing trends that contribute to national GDP for the adaptation of the 4IR for the transformation of smart Bangladesh. From the conceptual implication, companies and individuals are aware of the digital economy, which would lessen digital divide and create a strong link between technology and the economy. Furthermore, establishing customer confidence and trust would be a big issue for Bangladesh's digital platform economy in the future days. From a practical standpoint, IT industries and commercial organizations would have to deal with emerging 4IR and its technologies. The job market would also be expanded in a variety of areas, which would ultimately benefit the national economy. According to the study's conclusions, the digital economy is predicted to expand its commercial and corporate opportunities. Future research might be extended based on qualitative approach towards a digital Bangladesh and create a better developing economy.

Different toll collection types of vehicles and different distribution of tollbooths lead to the toll plaza diverging area becoming a typical vehicle weaving area with frequent crossing behaviors and conflicts on highways. This study aims to identify contributing factors to conflict risks of four vehicle-following patterns in a toll plaza diverging area by developing random parameters ordered logit models with heterogeneity in means and variances. The model can flexibly capture the unobserved heterogeneity of the contributing factors in different vehicle-following patterns. Real-world vehicle trajectory data obtained from the toll plaza diverging area in Nanjing, China, are used for model estimation. The results show that vehicle-following patterns with the same toll collection types have higher percentage of severe conflict risks. The average acceleration of the following vehicles, lane marking indicator, the initial lanes and lane-changes of vehicles are significantly associated with the collision risk levels. The standard deviation of surrogate safety measures of all vehicles in sub-segments are found differ significantly between vehicle-following patterns. Furthermore, a series of likelihood ratio tests are adopted to test the spatial dependence in sub-segments of the diverging area. The findings of this study could provide valuable information for safety improvement in toll plazas.

Drought stress is a major production constraint in crops globally. Crop wild relatives are important source of resistance and tolerance for both biotic and abiotic stresses, respectively. A breeding program was initiated to introgress drought tolerance in sunflower through hybridization between the wild species Helianthus argophyllus and the cultigen pool of H. annuus. Selection was carried out in the F2 to F5 segregating populations for high cuticular waxes, smaller leaf area, single heading and high oil content. The selected F5 breeding lines were compared with non-adapted elite sunflower germplasm in a replicated randomized complete block research project using different water treatments comparing fully irrigated (T0), with 75 (T1), 50 (T2) and 25% (T3) irrigation treatments. The comparison between the two types of germplasm showed that drought tolerant breeding lines had comparatively lesser decreases in leaf area, shoot weight and root shoot ratio 10 under the various drought treatments. Leaf area of the drought selected F5 lines were smaller than that of the elite germplasm under controlled irrigated treatments, but they maintained their leaf area under the drought treatments. Several drought resistant promising lines D-2, D-5, and D-27 were identified and showed high leaf area, great root length and increase root to shoot ratio under the highest stressed treatments (T3). Some of the lines could be directly used for the development of drought tolerant hybrids. Combining ability test indicated D-27 (F7) as good general combiner for seed yield plant−1 and oil contents when mated with male line RSIN.82. These hybrids could help to minimize seed yield losses due to water stress and to achieve profitable cultivation of sunflower in 18 arid regions of Pakistan.

Payments for Ecosystem Services are a voluntary market-based instrument to remunerate provider(s) of ecosystem services by those who benefit from them. Our research aimed to create an ex-post evaluation framework to identify bottlenecks and elements hindering the success of a solution-driven PES scheme. The framework was applied to a case study to test its feasibility and concerns the provision of health and recreational services in the Medvednica Nature Park (Zagreb, Croatia). The framework was set up through three main sources: the study of PES implementation project documentation, semi-structured interviews with visitors and key stakeholders and web-scraping of TripAdvisor reviews of the park. The main findings confirmed society's interest in the park, but the lack of mapping, quantification, economic valuation and accounting of the services analysed, society's little or no demand to pay for their provision and confused knowledge of the property rights of some ecosystem service providers in the area limit the success of the PES scheme. The framework was useful to describe the chosen PES scheme and to identify bottlenecks and fragilities of the system in place, allowing to correct its application flaws and, on the other hand, to demonstrate its replicability in other contexts.

Predominantly rural areas make up half of Europe and account for about 20 per cent of the population. Yet most of them are among the least privileged regions in the European Union, with a GDP per capita significantly below the European average and with an average population age higher than in urban areas, although this gap will only slowly begin to narrow in the next decade. Together with a lack of connectivity, inadequate infrastructure, lack of diversified job opportunities and limited access to services, this makes rural areas a less attractive place to live and work. At the same time, however, rural areas actively participate in the EU's green and digital transition. Achieving the EU's digital goals for 2030 can offer more opportunities for the sustainable development of rural areas in areas other than agriculture, livestock and forestry, opening up new perspectives for the growth of manufacturing and, even more, service industries, and contributing to a better geographical distribution of services and industries. In this context, the objective of this work is the construction of a synthetic index of the welfare of European nations, through the Wroclaw taxonomic method and through the use of logit models, for the identification of best practices of local realities and the interpretation in a more im-mediated way of the fair and sustainable welfare of each European nation at a rural level

Background: Sickle cell disease (SCD) is a public health problem in the Democratic Republic of Congo. While reference sickle cell centers have been implemented in capital cities of African countries and have proven to be beneficial for SCD patients, they have never been set up in rural areas for families with very low sources of income. Method: A cohort of 143 children with SCD aged 10 years old (IQR (interquartile range): 6–15 years) (sex ratio male/female = 1.3) were clinically followed for 12 months without any specific intervention aside from the management of acute events, and then for 12 months with a monthly medical visit, biological follow-up, and regular prophylaxis. Results: The median age of patients at the diagnosis of SCD was 2 years (IQR: 1–5). The implementation of standardized and regular follow-ups in a new sickle cell referral center in a remote city showed an increase in the annual mean hemoglobin level from 50 to 70 g/L (p = 0.001), and a decrease in the lymphocyte count and spleen size (p < 0.001). A significant decrease (p < 0.001) in the average annual number of hospitalizations and episodes of vaso-occlusive crises, blood transfusions, infections, and acute chest syndromes were also observed. Conclusions: Creation of a sickle cell referral center and the regular follow-up of children with SCD are possible and applicable in the context of a remote city of an African country and represent simple and accessible measures that can reduce the morbimortality of children with sickle cell disease.

Objective: The objective of this study is to determine the epidemic dynamics and clinical features of COVID-19 in southern Hainan Island, China, and provide experience for other tropical areas of the world. Methods: This retrospective study included confirmed cases of COVID-19 in southern Hainan. All enrolled patients were treated in Sanya, and data on epidemiological and clinical features of the disease and infection prevention and control measures adopted by the local government during the epidemic were collected. Results: Of the 74 cases, 71 (95.95%) were imported from Wuhan, Hubei Province (47, 63.51%), other cities in Hubei Province (11, 14.86%), or provinces other than Hubei and Hainan (13, 17.57%). Three (4.06%) patients were infected in southern Hainan, including one autochthonous case in Sanya. Fifty-four cases (72.97%) were detected in Sanya, and 27 cases (27.03%) were diagnosed in other cities. The rate of severe or critical cases was 28.38% (21/74), and mortality was 2.7% (2/74). The serum lactate levels and base excess of severe-critical patients were higher than those of patients with mild-moderate disease. Multivariate logistic regression analysis showed that chronic conditions were risk factors for severe and critical COVID-19. Seventy-four patients were diagnosed with COVID-19 over a 22-day period in Sanya, and the epidemic period in the city was 48 days. The outbreak was controlled rapidly because the local government adopted strict infection prevention and control measures. Conclusions: The clinical characteristics of COVID-19 in Hainan Island were similar to those reported in other regions. In Sanya, the rate of severe and very severe cases was higher than in other regions; however, most cases were imported, and there was only one autochthonous case. The rapid control of the outbreak in Sanya may be related to the tropical climate, adoption of strict infection prevention and control measures, daily reporting of new cases, increased public awareness about the epidemic, and other emergency actions implemented by the local government.

COVID-19 is causing major turmoil around the globe, and the clinical trial industry is likely to face unprecedented challenges to health and business sectors. In an effort to find a suitable treatment and prevention options for COVID-19, several COVID-19 clinical trials are being planned and initiated, while a large number of clinical trials for non- COVID-19 indications are suffering delays. With over more than 1000 trials being disrupted and more trials being added to this category daily, there is a direct impact on trial site activation and patient enrolment. This analysis deals with the specific impacts of the COVID-19 pandemic on the clinical trial and pharmaceutical industry. The objective of this study is to provide an updated information of the disrupted clinical trials and its impact on various therapeutic areas and different drugs. Among the severely affected clinical trials, oncology and CNS trials are the hardest hit therapy areas.This article will certainly emphasize the need for advanced and innovative approaches to maintain the health of the clinical trial ecosystem by continuing the existing trials and the start of the new studies. We have to take and follow necessary actions to guarantee that the initiatives will not be locked during the COVID-19 pandemic, both for the treatment of patients and for the researchers to conduct decision-relevant clinical trials.

This study aims to assess the potential of the LDAS-Monde a land data assimilation system developed by Météo-France to monitor the impact of the 2018 summer heatwave over western Europe vegetation state. The LDAS-Monde is forced by the ECMWF’s (i) ERA5 reanalysis, and (ii) the Integrated Forecasting System High Resolution operational analysis (IFS-HRES), used in conjunction with the assimilation of Copernicus Global Land Service (CGLS) satellite derived products, namely the Surface Soil Moisture (SSM) and the Leaf Area Index (LAI). Analysis of long time series of satellite derived CGLS LAI (2000-2018) and SSM (2008-2018) highlights marked negative anomalies for July 2018 affecting large areas of North Western Europe and reflects the impact of the heatwave. Such large anomalies spreading over a large part of the considered domain have never been observed in the LAI product over this 18-yr period. The LDAS-Monde land surface reanalyses were produced at spatial resolutions of 0.25°x0.25° (January 2008 to October 2018) and 0.10°x0.10° (April 2016 to December 2018). Both configuration of the LDAS-Monde forced by either ERA5 or HRES capture well the vegetation state in general and for this specific event, with HRES configuration exhibiting better monitoring skills than ERA5 configuration. The consistency of ERA5 and IFS HRES driven simulations over the common period (April 2016 to October 2018) allowed to disentangle and appreciate the origin of improvements observed between the ERA5 and HRES. Another experiment, down-scaling ERA5 to HRES spatial resolutions, was performed. Results suggest that land surface spatial resolution is key (e.g. associated to a better representation of the land cover, topography) and using HRES forcing still enhance the skill. While there are advantages in using HRES, there is added value in down-scaling ERA5, which can provide consistent, long term, high resolution land reanalysis. If the improvement from LDAS-Monde analysis on control variables (soil moisture from layers 2 to 8 of the model representing the first meter of soil and LAI) from the assimilation of SSM and LAI was expected, other model variables benefit from the assimilation through biophysical processes and feedbacks in the model. Finally, we also found added value of initializing 8-day land surface HRES driven forecasts from LDAS-Monde analysis when compared with model only initial conditions.

Technology advancements are evident in the healthcare field; numerous new opportunities and applications have emerged during the last years based on embedded intelligence and related to real-time diagnosis of medical issues, tele-care and telemedicine, remote monitoring of patients, computer-assisted “smart” transportation in case of emergencies, as well as new types of remotely controlled surgical operations. This paper aims to provide an overview of the application of embedded intelligence in the field of healthcare; it gathers the main critical requirements, related technologies and research advancements up to date, and it presents the most important challenges that are yet to be faced. The main focus is given in the development and optimization of Body Area Networks (BANs) based on advanced embedded sensing devices, the optimization of smart gateways in such networks, and the provision of holistic scalable and secure solutions in the healthcare domain. In addition, the paper presents two principal use cases that stem from the combination of novel information and communication technologies with classic healthcare practices, explaining the functional and non-functional requirements, as well as the mixed criticality characteristics of the associated systems.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

Supply chain management requires regular updates of the location of assets, which can be enabled by low power wide area networks, such as Sigfox. While it is useful to localize a device simply by its communication signals, this is very difficult to do with Sigfox because of wide area and ultra narrowband nature. On the other hand, installing a satellite localization element on the device greatly increases its power consumption. We investigated using information about nearby Wi-Fi access points as a way to localize the asset over the Sigfox network, so without connecting to those Wi-Fi networks. This paper reports the location error that can be achieved by this type of outdoor localization. By using a combination of two databases, we could localize the device on all 36 test locations with a median location error of 39 m. This shows that the localization accuracy of this method is promising enough to warrant further study, most specifically the minimal power consumption.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

The aim of this randomized controlled clinical trial was to compare the 2-year clinical performance of resin composite restorations placed at non-caries cervical lesions (NCCL) with one-step self-etch, total-etch, and selective enamel etch & self-etch adhesive techniques. Thirty-two patients received three resin composite restorations each at NCCLs (Tetric EvoCeram/Ivoclar/Vivadent), bonded with a total-etch adhesive agent (ExciTE F/Ivoclar/Vivadent) and a self-etch (AdheSE One F/Ivoclar/Vivadent) without and with selective enamel etching. All restorations were evaluated by two examiners at baseline, 6-, 12-, 18- and 24-months post-operation regarding retention, caries occurrence, marginal adaptation, and marginal staining. A logistic regression analysis with generalized estimating equations was used. After 2 years, the retention rate was 86,8% for total-etch, 92.26% for self-etch, and 93.63% for selective enamel etching & self-etch. No caries were detected during all the restorations. Concerning marginal adaptation, the clinically perfect restorations were 26.9% for the total-etch technique, 16% for self-etch, and 25,9% for selective enamel etch & self-etch. All three adhesive strategies provided restorations with no significant differences in the retention rate and the marginal adaptation, whereas the total etch yielded better performance for marginal staining. All the restorations were assessed as clinically acceptable after 2 years.

This review is focused on synephrine, the principal phytochemical found in bitter orange and other medicinal plants, and widely used as a dietary supplement for weight loss/body fat reduction. We examine different aspects of synephrine biology, delving into its established and potential molecular targets, as well as its mechanisms of action. We present an overview of the origin, chemical composition, receptors, and pharmacological properties of synephrine, including its anti-inflammatory and anti-cancer activity in various in vitro and animal models. Additionally, we conduct a comparative analysis of the molecular targets and effects of synephrine with those of its metabolite, selective glucocorticoid receptor agonist (SEGRA) Compound A (CpdA), which shares a similar chemical structure with synephrine. SEGRA, including CpdA, have been extensively studied as glucocorticoid receptor activators that have a better benefit/risk profile than glucocorticoids due to the reduced adverse effects. We discuss the potential of synephrine usage as a template for the synthesis of new generation of non-steroidal SEGRA. The review also provides insights into the safe pharmacological profile of synephrine.

The Selective Paste Intrusion (SPI) method is a layer-by-layer additive manufacturing technique that allows for the production of complex geometries in concrete elements by selectively bonding aggregates with cement paste in a particle bed. To create reinforced concrete, the Wire and Arc Additive Manufacturing (WAAM) process shall be integrated into SPI. This technique allows the production of almost free-formed reinforcement and thus complements the advantage of SPI to produce free-formed structures of almost any geometry. However, integration of WAAM into SPI poses a considerable challenge, as high temperatures are generated during the welding process. These temperatures can negatively affect the rheological properties of the cement paste, in turn the penetration behavior of the paste in the particle bed and, subsequently, the mechanical properties of the hardened concrete. A possible passive cooling strategy is to increase the protruding length of the reinforcement bars out of the particle-bed. This requires that the distance of the print nozzle to the particle bed is as well increased, since it must be possible to move it across the reinforcement. The objective was thus to investigate the effect of that distance on print quality and to quantify a maximum allowable distance for an adequate print quality (for the printer setting used) in terms of shape accuracy and concrete strength. Compressive and flexural strength tests as well as geometrical measurements using a 3D scanning method were performed on specimen, printed with varying print nozzle to particle bed distances. It can be stated that for the used SPI print-heads, nozzle-types and parameter settings, the distance between the nozzle and the particle bed should not exceed 50 mm to ensure sufficient print quality in both shape accuracy and mechanical strength.

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

In individuals with spinal cord injury (SCI), rapid skeletal muscle atrophy and metabolic dysfunction pose profound rehabilitation challenges, often resulting in substantial loss of muscle mass and function. This study evaluates the effect of combined neuromuscular electrical stimulation (Comb-NMES) on skeletal muscle cross-sectional area (CSA) and inflammatory signaling within the acute phase of SCI. We applied a novel Comb-NMES regimen, integrating both high-frequency resistance and low-frequency aerobic protocols on the vastus lateralis muscle, to participants early post-SCI. Muscle biopsies were analyzed for CSA and inflammatory markers pre-and post-intervention. The results revealed a preservation of muscle CSA in the Comb-NMES group compared to a control group receiving transcutaneous electrical nerve stimulation and passive movements. Inflammatory signaling proteins such as TLR4 and Atrogin-1 were downregulated, whereas markers associated with muscle repair and growth were modulated beneficially in the Comb-NMES group. The study's findings suggest that early application of Comb-NMES post-SCI can attenuate inflammatory pathways linked to muscle atrophy and potentially promote muscle repair, advocating for its inclusion in early rehabilitation efforts. However, the small sample size and variability in injury characteristics emphasize the need for further research to corroborate these results across a more diverse and extensive SCI population.

Myanmar is located in the Indo-Burma biodiversity hotspot, but lacks understanding of the bio-diversity hotspots and protected areas within its borders. Climate change affects the effective-ness of protected areas and the potential distribution range of species. Based on Myanmar's re-gional characteristics, endangered status, and representativeness, this paper selects species and identifies biodiversity hotspots using the MaxEnt model. We studied the biodiversity within the terrestrial protected area network in Myanmar, as well as the potential for cross-boundary range shifts among protected areas under different climate scenarios. Species populations outside My-anmar's protected area network may not be able to find suitable habitats in the future, further exacerbating climate-related extinction risks. Additionally, some protected areas in Myanmar may not be fully utilizing their biodiversity representation potential, and with scientific spatial planning, Myanmar's protected areas could support a large number of species. In the context of continued warming, identifying new protected areas that encompass the future and current climatic niches of protected areas can increase the capacity for sustained biodiversity conservation. We hope that this study provides insights for increasing the effectiveness of Myanmar's protect-ed area network and emphasizes the urgency of coordinated protection of protected areas and biodiversity hotspots.

Cardiac resynchronization therapy (CRT) via biventricular pacing (BiVP-CRT) is considered a mainstay treatment for symptomatic heart failure patients with reduced ejection fraction and wide QRS. However, up to one third of patients receiving BiVP-CRT are considered non-responders to the therapy. Multiples strategies have been proposed to maximize the percentage of CRT responders including two new physiological pacing modalities that have emerged during the lasts years: His bundle pacing (HBP) and left bundle branch area pacing (LBBAP). Both pacing techniques aim at restoring the normal electrical activation of the ventricles through the native conduction system in opposition to the cell-to-cell activation of conventional right ventricular myocardial pacing. Conduction system pacing (CSP), including both HBP and LBBAP appears to be a promising pacing modality for delivering CRT and has proven to be safe and feasible in this particular setting. This article will review the current state of the art of CSP-based CRT, its limitations and future directions.

A comparative study of the physicochemical properties of natural bentonite clays of Pogodayevо (Republic of Kazakhstan, mod.1) and Dash-Salakhli (Republic of Azerbaijan, mod.2) deposits and modification of the bentonite clay with polyhydroxocations of iron (III) and aluminium (III). It-wasestablished that the modification of natural bentonitesusing polyhydroxocations of iron (III) and aluminium(III) by the method of "co-precipitation" leads to a change in their chemical composition, structural and sorption properties. The results showed that hydroxy-aluminum cations ([Al3O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe were intercalated into clay layers, which led to an increase in the values of d001 and specific surface areas compared to those of the original bentonite, from 37 to 120 for the Pogodaevo bentonite and from 51 to 172 respectively for bentonite from the Dash-Salakhli deposit. It is shown that modified sorbents based on natural bentonite are finely porous objects with a predominance of pores of 1.5−6.0 nm in size. As a result, there is a significant increase in the specific surface area of sorbents. Modification of bentonite with polyhydroxocations of iron (III) and aluminium (III) by the "co-precipitation" method also leads to an increase in the sorption capacity of the sorbents obtained with respect to nickel (II) cations. Modified bentonites were used for the adsorption of Ni (II) ions from the model solution. Ni (II) was absorbed in a neutral pH solution. The study of equilibrium adsorption showed that the data are in good agreement with the Langmuir isotherm model. The maximum adsorption capacity of the Ni (II) monolayer obtained from the Langmuir equation was 25.0 mg/g (mod. 1_Al_5-c), 18.2 mg/g (mod. 2_Al_5-c) for Al-bentonite and 16.7 mg/g (mod. 1_Fe_5-c), 10.1 (mod. 2_Fe_5-c) for Fe-bentonite. The kinetics of adsorption is considered. The high content of Al-OH anion exchange centresin them determines the higher sorption activity of Al-modified bentonites.

ORB (Oriented FAST and Rotated Brief) features are the most commonly used features in visual SLAM and visual odometry that have high computational speed, and rotation scale invariance. However, due to the homogenization of ORB features, the corner properties of specific features are poor in some artificial environments, and it can lead to poor matching performance when the environmental texture is not rich. The underlying reason is that the pixel grayscale changes in the less-richly textured regions on the image are not obvious, leading to a certain degree of mis-matching in the matching process. At the same time, when the camera motion speed is low, there is much overlap between adjacent frames. This results in minimal or almost no changes in the projection of feature points, and the system is highly sensitive to errors, In this case, even small errors can cause significant fluctuations in the calculation results. In response to the above issues, an improved feature point method for stereo vision mileage calculation is proposed to solve the problem of system stability deterioration when cameras move at low speeds in artificial envi-ronments. Firstly, weight calculation based on different texture regions is used to solve the problem of low corner properties of feature points caused by environmental texture differences. Then, keyframes are used for motion model estimation to improve the system's stability under low-speed motion. The experimental results of the dataset showed that the key frame rate was optimal between 10% and 12%, and the positioning accuracy was higher than these open-source systems compared with three common open-source VO systems.

Cropland area is closely related to food production. More previous focuses were paid on impacts of extreme events on food production, but less on cropland dynamics. This study took the Farming-Pastoral Ecotone of Northern China (FPEN) as a case area, to investigate its cropland area dynamics and driving factors in view of perspectives of extreme events, environmental conditions, socioeconomic development, urban expansion, and ecological construction. We used ridge regression approach to quantify contributions of these drivers to cropland area dynamics. Results showed that cropland area increased significantly at a rate of 333.5km2/a during 1992−2020 and were spatially clustered in east of the FPEN. Impact extent and size each driving factor on cropland trend presented large spatiotemporal differences, but ecological construction (EC) had overall the greatest impact on cropland area changes, followed by urban expansion (UE). In comparison, TL10p has the smallest. UE-dominated areas increased 41.9% since 2010s, but still less than EC. Furthermore, we found that extreme events effects on cropland area trend evidently increased. Particularly, TH90p displayed the most increase (~99.4%). Cropland area changes dominated by extreme temperature events in 2010−2020 increased nearly six times than that in 1992−2010. These findings suggest that increasing impacts of extreme weather events on cropland area changes should be cautioned.

For the traditional indoor visible light communication heterogeneous network switching algorithm is only concerned with the research of vertical switching algorithm, however, the research of horizontal vertical collaborative switching combined with multi-carrier modulation technology is seldom mentioned, based on the above, this paper proposes a horizontal-vertical collaborative switching strategy based on the residency time of the communication blind area. Firstly, we use asymmetrically clipped optical OFDM (ACO-OFDM) for signal processing to reduce the bit error rate (BER) of the system by reducing the multipath interference generated during signal transmission.Secondly, the BER is used to determine the communication blind area and to calculate its dwell time. Finally, the threshold time is set as the channel interruption time in the communication blind zone, and the horizontal-vertical cooperative switching is performed by comparing with the dwell time. The simulation results show that the average network throughput is 195.28Mbps, and the average number of handovers is 1.35. Compared with instant vertical handover (IVHO) scheme and dwell vertical handover (DVHO) scheme, the average network throughput is improved by 37.21% and 28.45%, respectively, and the average switching times are reduced by 28.05% and 5.27%, respectively.

Conservation of tropical endemic amphibians largely suffers from Wallacean shortfall, a gap to which predictive species distribution models have contributed significantly to bridge by delineating probable distribution and the underlying suitable habitat within their distributional range. However, rarely is a prediction model ground-truthed to evaluate their predictive performance. Here we present a species distribution modeling approach using maximum entropy algorithm corrected for smaller sample size, in guiding explorative surveys aimed at optimizing survey effort and discovering unrecorded populations of Zhangixalus suffry, a rhacophorid tree-frog endemic to the northeastern part of the Indian subcontinent along with the factors limiting their distribution. With only 16 established historical locality data to model for (after spatial thinning to reduce autocorrelation) and a set of environmental predictors (climatic, topographic, and landscape composition), our model prediction enabled the successful discovery of seven new population records from unreported landscapes, extending its southernmost distributional limit over a considerable distance. The final composite distribution model combining all the locality records (n=23) predicted similar core areas of suitable habitat consistent with the known geographic distribution of the species but showed poor representation under existing coverage of Protected Area (PA) network in the Region with only 7% representation of suitable habitat under protection. Habitat suitability of a site was significantly governed by factors related to precipitation (precipitation seasonality and precipitation of the warmest quarter) and topographic factors that can influence it (elevation and aspect). This corroborates with the known ecology of Rhacophorid frogs, especially concerning their seasonal explosive reproductive strategy and foam nest-building behavior.Through this study, we propose explorative surveys guided by species distribution models to expedite unknown population discovery of rare, tropical endemic amphibians and using such taxa as surrogates in identifying conservation priority zones that can be directly applied to reserve design and conservation and management planning.

The purpose of this study was to clarify the attachment types of the tibialis anterior tendon (TAT) in Japanese fixed cadavers and to determine the attachment site area in three dimensions. We examined 100 feet from 50 Japanese cadavers. The TAT was classified according to differences in the number of fiber bundles as: Type I, with one fiber bundle; Type II, with two fiber bundles; and Type III, with three fiber bundles. The attachment site area of the TAT was measured using a three-dimensional scanner. Cases were Type II in 95% and Type III in 5%, with no cases of Type I identified. In Type II, mean attachment site areas were 85.2 ± 18.2 mm2 for the medial cuneiform bone (MCB) and 72.4 ± 19.0 mm2 for the first metatarsal bone (1MB), showing a significantly larger area for MCB than for 1MB. These findings suggest the possibility of ethnic differences in TAT attachment types and suggest that TAT attachments in Japanese individuals are highly likely to be Type II, with rare cases of Type III. Accurate measurement of attachment site areas is possible with appropriate three-dimensional measurements.

A road network represents road objects in a given geographic area and their interconnections, and is an essential component of intelligent transportation systems (ITS) enabling emerging new applications such as dynamic route guidance, driving assistance systems, and autonomous driving. As the digitization of geospatial information becomes prevalent, a number of road networks with a wide variety of characteristics coexist. In this paper, we present an area partitioning approach to the conflation of two road networks with a large difference in level of details. Our approach first partitions the geographic area by the Network Voronoi Area Diagram (NVAD) of low-detailed road network. Next, a subgraph of high-detailed road network corresponding to a complex intersection is extracted and then aggregated into a supernode so that a high matching precision can be achieved via 1:1 node matching. To improve the matching recall, we also present a few schemes that address the problem of missing corresponding object and representation dissimilarity between these road networks. Numerical results at Yeouido, Korea's autonomous vehicle testing site, show that our area partitioning approach can significantly improve the performance of road network matching.

Amongst the advantages of using Worldwide Interoperability Microwave Access (WiMAX) technology at the last-mile level as access technology include an extensive range of 50 km Line of Sight (LOS), 5 to 15 km Non-Line of Sight and few infrastructure installations compared to other wireless broadband access technologies. Despite positive investments in ICT fibre infrastructure by developing countries, including Botswana, servicing end-users is subjected to high prices and service disparities. The alternative, the Wi-Fi hotspot initiative by the Botswana government, falls short as a solution for last-mile connectivity and access. This study used OPNET simulation Modeller 14,5 to investigate whether Botswana’s national broadband project could adopt WiMAX IEEE 802.16e as an access technology. Therefore, using the simulation method, this paper evaluates the WiMAX IEEE 802.16e/m over three subscriber locations in Botswana. The results obtained indicate that the deployment of the WiMAX IEEE 802.16e standard can solve most of the deployment issues and access at the last-mile level. Although the findings suggest that WiMAX IEEE 802.16e is more suitable for high-density areas, it could also solve rural areas’ infrastructure development challenges and provide the required high-speed connectivity access. However, unlike the Wi-Fi initiative, which requires more infrastructure deployment and less on institutional and regulatory frameworks, the deployment of WiMAX IEEE802.16e requires institutional and regulatory standards.

The log interpretation and evaluation of Chang 8 tight sandstone reservoir in Longdong West area, Ordos Basin, is facing great challenges due to the existence of low resistivity contrast oil pays. To better guide the exploration of oil resources in this area, the characteristics and control mechanism of low resistivity contrast oil pays were studied in this research. Firstly, according to the relative value of apparent resistivity increase rate of the target formation, the reservoir was divided into two types: low resistivity contrast oil pay (LRCP) and high resistivity oil pay (HRP). Then, the reservoir characteristics were studied by comparing and analyzing the experimental data, formation water data and logging data collected from the two reservoir types. On this basis, the control mechanism of LRCP was studied and summarized into reservoir micro factors and regional macro factors, respectively. It is found that the reservoir rock composition between LRCP and HRP is basically the same. Compared with HRP reservoir, the average porosity and permeability of LRCP reservoir are relatively better, but the pore structure is relatively poorer because of the high content of micro pores. When the filling pressure of crude oil is sufficient enough, the high oil saturation can be formed in LRCP reservoir. The high irreducible water saturation and high formation water salinity are the main micro factors reduced the reservoir resistivity. Besides, the difference of hydrocarbon expulsion capacity of source rock and the regional difference of formation water salinity are the macro factors influenced the distribution of LRCP and HRP from vertical and horizontal of the region. The formation of LRCP is controlled by the comprehensive influence of reservoir micro factors and regional macro factors. And the comprehensive consideration of the influence of micro factors and macro factors on LRCP is suggested during the log interpretation and evaluation.

The Maximum Entropy Theory of Ecology, or METE, is a theoretical framework of macroecology that makes a variety of realistic ecological predictions about how species richness, abundance of species, metabolic rate distributions, and spatial aggregation of species interrelate in a given region. In the METE framework, "ecological state variables" (representing total area, total species richness, total abundance, and total metabolic energy) describe macroecological properties of an ecosystem. METE incorporates these state variables into constraints on underlying probability distributions. The method of Lagrange multipliers and maximization of information entropy (MaxEnt) lead to predicted functional forms of distributions of interest. We demonstrate how information entropy is maximized for the general case of a distribution, which has empirical information that provides constraints on the overall predictions. We then show how METE’s two core functions are derived. These functions, called the "Spatial Structure Function" and the "Ecosystem Structure Function" are the core pieces of the theory, from which all the predictions of METE follow (including the Species Area Distribution, the Species Abundance Distribution, and various metabolic distributions). Primarily, we consider the discrete distributions predicted by METE.We also explore the parameter space defined by the METE’s state variables and Lagrange multipliers. We aim to provide a comprehensive resource for ecologists who want to understand the derivations and assumptions of basic mathematical structure of METE.

Detailed built-up area information is valuable for mapping complex urban environments. Although a large number of classification algorithms about built-up areas have been developed, they are rarely tested from the perspective of feature engineering and feature learning. Therefore we launched a unique investigation to provide a full test of the OLI imagery for 15-m resolution built-up area classification in 2015, in Beijing, China. Training a classifier requires many sample points, and we propose a method based on the ESA's 38-meter global built-up area data of 2014, Open Street Map and MOD13Q1-NDVI to achieve rapid and automatic generation of a large number of sample points. Our aim is to examine the influence of a single pixel and image patch under traditional feature engineering and modern feature learning strategies. In feature engineering, we consider spectra, shape and texture as the input features, and SVM, random forest (RF) and AdaBoost as the classification algorithms. In feature learning, the convolution neural network (CNN) is used as the classification algorithm. In total, 26 built-up land cover maps were produced. Experimental results show that: (1) the approaches based on feature learning are generally better than those based on feature engineering in terms of classification accuracy, and the performance of ensemble classifiers e.g., RF, is comparable to that of CNN. Two dimensional CNN and the 7 neighborhood RF have the highest classification accuracy of nearly 91%. (2) Overall, the classification effect and accuracy based on image patches are better than those based on single pixels. The features that can highlight the information of the target category (for example, PanTex and EMBI) can help improve classification accuracy.

In order to alter and adjust the shape of the membrane, cells harness various mechanisms of curvature generation. Many of these curvature generation mechanisms rely on the interactions between peripheral membrane proteins, integral membrane proteins, and lipids in the bilayer membrane. One of the challenges in modeling these processes is identifying the suitable constitutive relationships that describe the membrane free energy that includes protein distribution and curvature generation capability. Here, we review some of the commonly used continuum elastic membrane models that have been developed for this purpose and discuss their applications. Finally, we address some fundamental challenges that future theoretical methods need to overcome in order to push the boundaries of current model applications.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Alpha-fetoprotein (AFP) is a major embryo- and tumor-associated protein capable of binding and transporting variety of hydrophobic ligands including estrogens. AFP has been shown to inhibit estrogen receptor (ER)-positive tumor growth and this can be attributed to its estrogen-binding ability. Despite AFP has long been investigated, its three-dimensional (3D) structure has not been experimentally resolved and molecular mechanisms underlying AFP-ligand interaction remain obscure. In our study we constructed homology-based 3D model of human AFP (HAFP) with the purpose to perform docking of ERα ligands, three agonists (17β-estradiol, estrone and diethylstilbestrol) and three antagonists (tamoxifen, afimoxifene and endoxifen) into the obtained structure. Based on ligand docked scoring function, we identified three putative estrogen- and antiestrogen-binding sites with different ligand binding affinities. Two high-affinity sites were located in (i) a tunnel formed within HAFP subdomains IB and IIA and (ii) opposite side of the molecule in a groove originating from cavity formed between domains I and III, while (iii) the third low-affinity site was found at the bottom of the cavity. 100 ns MD simulation allowed studying their geometries and showed that HAFP-estrogen interactions occur due to van der Waals forces, while both hydrophobic and electrostatic interactions were almost equally involved in HAFP-antiestrogen binding. MM/GBSA rescoring method estimated binding free energies (ΔG_bind) and showed that antiestrogens have higher affinities to HAFP as compared to estrogens. We performed in silico point substitutions of amino acid residues to confirm their roles in HAFP-ligand interactions and showed that Thr132, Leu138, His170, Phe172, Ser217, Gln221, His266, His316, Lys453, and Asp478 residues along two disulfide bonds, Cys224-Cys270 and Cys269-Cys277 have key roles in both HAFP-estrogen and HAFP-antiestrogen binding. Data obtained in our study contribute to understanding mechanisms underlying protein-ligand interactions and anti-cancer therapy strategies based on ER-binding ligands.

The rapid development of electric vehicles, unmanned aerial vehicles, and wearable electronic devices has led to a high interest in research related to the synthesis of graphene with a high specific surface area for energy applications. However, the problem of graphene synthesis scalability, as well as the lengthy duration and high energy intensity of the activation processes of carbon materials, are significant disadvantages. In this study, a reactor was developed for the green, simple, and scalable electrochemical synthesis of graphene oxide with a low oxygen content of 14.1 %. The resulting material was activated using a fast joule heating method. The processing of mildly oxidized graphene with a high–energy short electrical pulse (32 ms) made it possible to obtain a graphene–based porous carbon material with a specific surface area of up to 1984.5 m2/g. The low energy intensity, simplicity, and use of environmentally friendly chemicals render the proposed method scalable.

This paper maps the causes of the demographic, economic and social decline of a selected border micro-region during the last century. The decline occurred due to the location being remote, lacking natural resources and having an unsuitable industrial structure. Historical events associated with the post-war deportation of the German population and efforts to create a classless society also played a role in the decline. The results are an 87% population decrease, the demise of most companies, a very low level of human capital and unemployment reaching up to 5%. In order to comprehend the current state of the border micro-region and predict future development, it is necessary to understand the development that has occurred since approximately the middle of the nineteenth century. The European countryside is certainly not homogeneous, and different regions have shown unique mixes of positional, natural, economic and political factors. Some hope has been raised in relation to the transition to a post-productive economy, a transition that turns the remoteness of the region into an advantage. This is confirmed by the positive migration balances of the smallest municipalities in the last decade.

Geospatial knowledge in massive academic papers can provide knowledge services such as location-based research hotspot analysis, spatio-temporal data aggregation, research results recommendation, etc. However, geospatial knowledge often exists implicitly in literature resources in unstructured form, which is difficult to be directly accessed and mined and utilized for rapid production of massive thematic maps. In this paper, we take the geospatial knowledge of the area studied as an example and introduce its extraction method in detail. An integrated feature template matching and random forest classification algorithm is proposed for accurately identifying research areas from the abstract texts of academic papers and producing thematic maps. Firstly, the precise recognition of geographical names is achieved step by step based on BiLSTM-CRF algorithm and improved heuristic disambiguation method; then, the area studied is extracted by the designed integrated feature recognition template of area studied using random forest classification algorithm, and a fast thematic map is designed for the knowledge of area studied, topic and literature. The experimental results show that the area studied recognition accuracy can reach 97%, the F-value is 96%, and the recall rate reaches 96%, achieving high accuracy and high efficiency of area studied extraction in text. Based on the geospatial knowledge, the thematic map can achieve the effect of fast map formation and accurate expression.

Micro-nanoparticles' characteristics in geothermal fluids can be applied to detect of deep hidden geothermal resources. Observations using a nanoparticle tracking analyzer (NTA) indicated that the karst geothermal water collected in the central area of Shandong Province (Jinan and Zibo) contains many natural micro-nanoparticles with sizes primarily ranging between 100 nm and 5 μm. The micro-nanoparticles’ type, shape, crystal form, and chemical composition in the samples were analyzed using transmission electron microscopy (TEM). TEM images and energy dispersive spectroscopy showed that the micro-nanoparticles in geothermal water samples were mostly amorphous, irregular, or nearly spherical, with rough edges. The micro-nanoparticles were mainly carbonates, sulfates, and chlorine-containing Fe, Ca, Na, and Mg. The characteristics of the particles can reveal the properties of the deep, hot reservoirs and aquifers from where they originate. Therefore, we believe that natural micro-nanoparticles can be essential to detecting and studying deep, hidden geothermal resources, which is a novel approach to exploring deep, hidden geothermal resources.

The Savu Sea holds significant importance as a conservation area in Indonesia, providing sustenance and livelihoods for local communities. It is situated within the Coral Triangle, a critical hotspot for marine biodiversity worldwide. However, the Savu Sea is currently facing various threats, including overfishing, pollution, and the impacts of climate change. Effective management of this conservation area relies heavily on the active participation of local communities. Therefore, this study aims to address this issue by analyzing how factors within these communities, such as the socio-economic condition of coastal households, environmental awareness, the existence of community-based conservation areas, attitudes towards activities within the conservation area, and participation in multistakeholder institutions, contribute to a positive perception of the benefits provided by the Savu conservation area. To determine the complex causal conditions that influence the outcome of perception, the study employs the Qualitative Comparative Analysis (QCA) method, specifically using crisp set QCA (csQCA). A survey was conducted among 22 coastal villages surrounding the Savu Sea, resulting in the identification of 14 different combinations of pathways that contribute to varying levels of perception regarding conservation. Valuable lessons can be drawn from this study to enhance the design of policies aimed at effectively managing the Savu conservation area.

The CAN protocol is widely adopted for in-vehicle networks due to its cost efficiency and reliable transmission. However, despite its popularity, the protocol lacks built-in security mechanisms, making it vulnerable to various attacks such as flooding, fuzzing, and DoS. These attacks can exploit vulnerabilities and disrupt the normal behavior of the in-vehicle network. One of the main reasons for these security concerns is that the protocol relies on broadcast frames for communication between ECUs within the network. To tackle this issue, this paper presents an intrusion detection system that leverages multiple LSTM-Autoencoders. The proposed system utilizes diverse features, including transmission interval and payload value changes, to capture various characteristics of normal network behavior. By analyzing different types of features separately using the LSTM-Autoencoder model, the system effectively detects anomalies. In our evaluation, we conducted experiments using real vehicle network traffic, and the results demonstrated the system's high precision with a 99% detection rate in identifying anomalies.

With the vast amount of goods being shipped around the world, there is a need to track and manage various types of assets, particularly shipping containers. Logistics industries dealing with small facilities, shipments, equipment, and vehicles must be tracked. There are many applied asset tracking systems such as Radio-Frequency Identification (RFID), Bluetooth Low Energy (BLE) Beacon, and Long-Range Radio (LoRa). This paper presents these systems and focuses on locating assets using LoRaWAN technology, which has a positive impact on the responsive and sustainable cities in Egypt. IoT-based Long Range (LoRa) is a low-power, wide-area communication technology that uses radio frequencies to transmit data over long distances. The extended range, low power consumption, low maintenance, and the ability to store location data when the end node that needs to connect to the asset is out of the gateway's coverage make LoRa a good choice for developing asset-tracking applications. This paper introduces a real-time tracking experiment as a result of a project implementation, whose goals are aligned with industry, innovation, and infrastructure and Sustainable Cities and Communities, the Sustainable Development Goals (SDGs) No. 9 and 11.

The metro station ridership features are associated significantly with the built environment factors of the pedestrian catchment area surrounding metro stations. The existing studies have focused on the impact on total ridership at metro stations, ignoring the impact on varying patterns of metro station ridership. Therefore, the reasonable identification of metro station categories and built environment factors affecting the varying patterns of ridership in different categories of stations is very important for metro construction. In this study, we developed a data-driven framework to examine the relationship between varying patterns of metro station ridership and built environment factors in these areas. By leveraging smart card data, we extracted the dynamic characteristics of ridership and utilized hierarchical clustering and K-means clustering to identify diverse patterns of metro station ridership, and finally identified six main ridership patterns. We then developed a new built environment measurement framework and adopted multinomial logistic regression analysis to explore the association between ridership patterns and built environment factors. (1) The clustering analysis result revealed that six station types were classified based on varying patterns of passenger flow, representing distinct functional characteristics. (2) The regression analysis indicated that diversity, density, and location factors were significantly associated with most station function types, while destination accessibility was only positively associated with employment-oriented type station, and centrality was only associated with employment-oriented hybrid type station. These results could inform the coordinated development of rail transit and land use, and the renewal and enhancement of the built environment in the pedestrian catchment area surrounding metro stations.

We found an important fact that the beam footprint line of Ping will intersect with the real water depth when the initial incidence angle is about 45°, and sound velocity error hardly has an effect on it. This is contrary to our previous experience that the soundings of the central beam of multi-beam bathymetric system (MBS) is the most accurate. Firstly, the influence of sound velocity errors on central beam and seafloor topography distortion was analyzed. Secondly, the process of proving this fact was given, and the topography correction method was proposed by compensating the sound velocity profile area (SVP area). Finally, we showed in the first simulation of four type errors in SVPs that this fact is verified. The topography correction method used in the second simulation to correct the topography distortion of the first simulation is also verified.

As early as February 2020, many countries have started imposing measures to curb the spread of Covid-19. Despite the right intention, it is a challenging moment for the people, especially the rural population living in the coastal areas. The document presents the preliminary findings on the impacts of Covid-19 on the small scale fisheries in Tun Mustapha Park, Sabah, Malaysia.

For traffic management under sudden disaster in high-density areas, the first and foremost step is to prevent traffic congestion in the disaster-affected area by traffic flow control, as to provide enough and flexible traffic capacity for emergency evacuation and emergency rescue. Catastrophe border identification is the foundation and the key to traffic congestion prediction under sudden disaster. This paper uses a mathematical model to study the regional traffic flow in the high-density area under sudden fire disaster based on the Cusp Catastrophe Theory (CCT). The catastrophe border is identified by fitting the CCT-based regional traffic flow model to explore the stable traffic flow changing to the instable state, as to provide a theoretical basis for traffic flow manage and control in disaster-affected areas, and to prevent the traffic flow being caught into disorder and congestion. Based on VISSIM simulator data by building simulation scenarios with and without sudden fire disaster in a Sudoku traffic network, the catastrophe border is identified as 439pcu/lane/h, 529pcu/lane/h, 377pcu/lane/h at 5s, 10s, 15s data collection interval respectively. The corresponding relative precision, which compares to the method of Capacity Assessment Approach (CAA), is 89.1%, 92.7% and 76.5% respectively. It means that 10s data collection interval would be the suitable data collection interval in catastrophe border identification and regional traffic flow control in high-density area under sudden fire disaster.

The Sentinel Application Platform (SNAP) architecture facilitates Earth Observation data processing (http://step.esa.int/main/toolboxes/snap/). In this work we present results from a new Snow Processor for SNAP. We also describe physical principles behind the developed snow property retrieval technique based on the analysis of Ocean and Land Colour Instrument (OLCI) onboard Sentinel-3A/B measurements over clean and polluted snow fields. Using OLCI spectral reflectance measurements in the range 400-1020nm, we derive important snow properties such as spectral and broadband albedo, snow specific surface area, snow extent and grain size on the spatial grid of 300m. The algorithm also incorporates cloud screening and atmospheric correction procedures over snow surfaces. We present validation results using ground measurements from Antarctica, the Greenland ice sheet and the French Alps. We find the spectral albedo retrieved with accuracy of better than 3% on average, making our retrievals sufficient for a variety of applications. Broadband albedo is retrieved with the average accuracy of about 5% over snow. Therefore, the uncertainties of satellite retrievals are close to experimental errors of ground measurements. The retrieved surface grain size shows good agreement with ground observations. Snow specific surface area observations are also consistent with our OLCI retrievals. We present snow albedo and grain size mapping over the inland ice sheet of Greenland for areas including dry snow, melted/melting snow and impurity rich bare ice. The algorithm can be applied to OLCI Sentinel-3 measurements providing an opportunity for creation of long – term snow property records essential for climate monitoring and data assimilation studies - especially in the Arctic region, where we face rapid environmental changes including reduction of snow/ice extent and, therefore, planetary albedo.

Based on the topology of wide area protection system (WAPS), after studying the reliability of hardware system and information flow in the WAPS and establishing the reliability assessment model, the multi-service reliability analysis method with multi monitoring and protection tasks in WAPS was proposed. In the model, the impact of network quality of service (QoS) such as information flow loss and delay, is studied. On the base of the model, the multi-service reliability evaluation method is employed to analyze the reliability of a WAPS of IEEE14 node power system, and the key nodes of the WAPS is given, which provides a basis for improving the reliability of the WAPS.

1) Objective: to evaluate the effects of excitatory transcranial magnetic stimulation of the anterior intraparietal area in chronic patients with a frontal lesion and parietal sparing due to stroke on the impaired upper (UL) and lower limb (LL) as measured by Fugl-Meyer Assessment (FMA). 2) Methods: three patients (P1: 49.83/2.75, P2: 53.17/3.83, P3:63.33/3.08 years-old at stroke/years post-stroke, respectively) received two weeks (five days/ week) of rTMS at 10 Hz of the left anterior intraparietal area (AIP). A patient was treated in similar conditions with a sham coil (56.58/4.33) No complimentary therapy was delivered during the study. Patients were evaluated before, after- and two-months post-treatment (A1, A2 and A3, respectively). 3) Results: We found increased scores for lower limb in motor function subsection for P1 and P3 and in sensory function for P2 by A2 that remained at A3. We also found an increased score for upper limb motor function for P2 and P3, but the score decreased by A3 for P2. P3 score for upper limb ROM increased by A3 compared to A1 and A2. 4) Conclusion: AIP excitatory rTMS increased the FMA scores for lower and upper limb function, showing a broader effect when compared to M1 stimulation.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

The new diprotic ligand 3,5-di-tert-butylsalicylaldehyde 4-ethyl-3-thiosemicarbazone, abbreviated H2(3,5-t-Bu2)-sal4eT, exists as the thio-keto tautomer and adopts the E-configuration with respect to the imine double bond as evidenced by single-crystal X-ray analysis and corroborated by spectroscopic characterisation. Upon treatment with Cu(OAc)2·H2O in the presence of either 2,9-dimethyl-1,10-phenanthroline (2,9-Me2-phen) or 1,10-phenanthroline (phen) as a co-ligand in MeOH, this thiosemicarbazone undergoes conformational transformation (relative donor-atom orientations: syn,anti → syn,syn) concomitantly with tautomerization and double deprotonation to afford the ternary copper(II) complexes [Cu{(3,5-t-Bu2)-sal4eT}(2,9-Me2-phen)] (1) and [Cu2{3,5-t-Bu2)-sal4eT}2(phen)] (2). Crystallographic elucidation has revealed that complex 1 is a centrosymmetric dimer of mononuclear copper(II) complex molecules brought about by intermolecular H-bonding. The coordination geometry at the copper(II) centre is best described as distorted square pyramidal in accord with the trigonality index (τ = 0.14). The co-ligand adopts an axial-equatorial coordination mode; hence there is a disparity between its two Cu–N coordinate bonds arising from weakening of the apical one as a consequence of the tetragonal distortion. The axial X-band ESR spectrum of complex 1 is consistent with retention of this structure in solution. Complex 2 is a centrosymmetric dimer of dinuclear copper(II) complex molecules exhibiting intermolecular H-bonding and π-π-stacking interactions. The two copper(II) centres, which are 4.8067(18) Å apart and bridged by the thio-enolate nitrogen of the quadridentate thiosemicarbazonate ligand, display two different coordination geometries, one distorted square planar (τ4 = 0.082) and the other distorted square pyramidal (τ5 = 0.33). Such dinuclear copper(II) thiosemicarbazone complexes, which are crystallographically characterised, are extremely rare. In vitro, complexes 1 and 2 outperform cisplatin as antiproliferative agents in terms of potency and selectivity towards HeLa and MCF-7 cancer cell lines.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Targeted therapies with antiangiogenic drugs (e.g., sunitinib) and immune checkpoint inhibitors (e.g., anti-PD-1 antibodies) are the standard of care for patients with metastatic renal cell carcinoma. Although these treatments improve patient survival, they are rarely curative. We previously hypothesized that advanced cancers might be treated without drugs by using artificial diets in which the levels of specific amino acids (AAs) are manipulated. In this work, after showing that AA manipulation induces selective anticancer activity in renal cell carcinoma cells in vitro, we evaluated the anticancer activity of 17 artificial diets in a challenging animal model of renal cell carcinoma. The model was stablished by injecting murine renal cell carcinoma (Renca) cells into the peritoneum of immunocompetent BALB/cAnNRj mice. Mice survival was markedly improved when their normal diet was replaced with our artificial diets. Mice fed a diet lacking six AAs (diet T2) lived longer than mice treated with sunitinib or anti-PD-1 immunotherapy; several animals lived very long or were cured. Controlling the levels of several AAs (e.g., cysteine, methionine and leucine) and lipids was important for the anticancer activity of the diets. Additional studies are needed to further evaluate the therapeutic potential of this simple and inexpensive anticancer strategy.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

The amorphous Fe77Cu1Si13B9 ribbons were treated with pulsed laser interference heating (PLIH). It was confirmed here that the use of the laser heating process allowed for obtaining two-dimensional crystallised micro-areas, periodically distributed (at a distance of 17µm) on the surface of the amorphous ribbons. The correlation between structural changes (SEM, TEM, HRTEM) and the distribution of magnetic field lines of heated amorphous Fe77Cu1Si13B9 (FeCuSiB) ribbons is presented. Particular attention is paid to structure changes in micro-areas where, by controlling the laser interference heating process, partial crystallisation of amorphous alloys and the formation of clusters or single nanocrystallites (α-Fe(Si)) embedded in an amorphous matrix are given. The addition of copper to the FeSiB alloy promoted inhibition of grain growth. Electron holography of micro-areas confirmed shifts of the magnetic field lines in the areas of nanocrystallites, the presence of which in the structure caused magnetisation of the surrounding amorphous matrix.

Leaf mass per area (LMA) is a key structural parameter that reflects the functional traits of leaves and plays a vital role in simulating the material and energy cycle of plant ecosystems. In this study, vertical whorl-by-whorl sampling of LMA was conducted in a young Larix principis-rupprechtii plantation during the growing season at the Saihanba Forest Farm. The vertical and seasonal variations in LMA were analysed. Subsequently, a predictive model of LMA was constructed. The results revealed that the LMA varied significantly between different crown whorls and growing periods. In the vertical direction of the crown, the LMA decreased with increasing crown depth, but the range of LMA values from the tree top to the bottom was, on average, 30.4 g/m2, which was approximately 2.5 times greater in the fully expanded phase than in the early leaf-expanding phase. The LMA exhibited an allometric growth trend that increased during the leaf-expanding phase and then tended to stabilize. However, the range of LMA values throughout the growing period was, on average, 40.4 g/m2. Among the univariate models, the leaf dry matter content (LDMC) performed well (Ra2=0.45, RMSE=13.48 g/m2) in estimating the LMA. The correlation between LMA and LDMC significantly differed at different growth stages and at different vertical crown whorls. The dynamic predictive model of LMA constructed with the RDINC and DOY as independent variables was reliable in both the assessments (Ra2=0.68, RMSE=10.25 g/m2) and the validation (MAE=8.05 g/m2, FI=0.682). Dynamic simulations of crown LMA provide a basis for elucidating the mechanism of crown development and laying the foundation for the construction of an ecological process model..

In Taiwan, mountainous areas account for approximately two-thirds of the total area. The steep terrain and concentrated rainfall during typhoons cause landslides, which pose a considerable threat to mountain settlements. Therefore, models for analyzing rainfall-induced landslide hazards are urgently required to ensure adequate land use in mountainous areas. In this study, focusing on Pingtung County in southern Taiwan, we developed a landslide hazard index (IRL) to land use. Using FORMOSA-2 and SPOT-5 satellite images, data were collected before and after four typhoons (one in 2009 and three in 2013). The ArcGIS random tree classifier was used for interpreting satellite images to explore surface changes and disasters, which were used to analyze slope disturbances. The product of the maximum 3-h rolling rainfall intensity and effective accumulated rainfall was used as a rainfall trigger index (IRT). Considering environmental and slope disturbance factors, an index of slope environmental strength potential (ISESP) was developed through logistic regression (LR). Landslide hazard to land use was estimated using IRT and ISESP. The average coefficient of agreement (Kappa) was approximately 0.71 (medium to high accuracy); the overall accuracy of slope environmental strength potential analysis was approximately 80.4%. At a constant ISESP, IRT increased with the increasing hazard potential of rainfall-induced landslides. Furthermore, IRT and ISESP were positively correlated with landslide occurrence. When large ISESP values occur (e.g., fragile environment and high land development intensity), small IRT values may induce landslides.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.