The study of mechanical properties of rock mass can be effectively carried out through rock-like material model test. The similarity of mechanical properties between rock-like material and protolith is dependent on the appropriate selection of composition and content of rock-like materials. In this research, X-Ray diffraction test was conducted to analyze the composition of deep rock, which confirmed silica, quartz, and dolomite as the primary components of deep sandstone. An orthogonal design test was used to execute the ratio test of rock-like material. River sand was used as an aggregate, cement as a binder, gypsum powder as a regulator, and polystyrene foam (EPS) as rock damage simulation material. The influencing factors considered in the orthogonal mechanical tests were the proportion of aggregate and binder, ratio of binder and regulator, quantity of damage simulation material, and size of damage simulation material. Three levels were set for each factor, and mechanical parameters such as compressive strength, tensile strength, elastic modulus, axial strain, and Poisson's ratio were tested for each group of samples. The changes of those parameters with the levels of the above four factors were studied. The study revealed that adjusting the size of polystyrene foam (EPS) can adjust the values of elastic modulus, tensile strength, and Poisson's ratio of rock-like material. Similarly, changing the ratio of binder and regulator can adjust the values of axial strain and compressive strength of rock-like material. The rock-like material developed in the study can simulate the mechanical properties of different rock masses such as granite, sandstone, shale, and limestone.

Manual measurement of rock discontinuities is time-consuming and subjective according to the experience of the surveyor. This work proposes a three-dimensional laser scanning-based method for the semi-automatic identification of rock discontinuities. Multisite cloud scanning is performed with real-time kinematic (RTK)-assisted orientation to estimate the rock fracturing degree; then, discontinuity orientations are extracted with the man–machine interactive method or automatic method. The proposed method was applied to actual examples to illustrate its accuracy at identifying rock discontinuities. The sensitivity of the identification accuracy to different parameters was investigated.

Over the years, various models have been developed in the stages of the mining process that have allowed predicting and enhancing results, but it is the breakage the variable that connects all the activities of the mining process from the point of view of costs (drilling, blasting, loading, hauling, crushing and grinding). To improve this process, we come up with an idea to develop a breakage prediction model; on the basis of the main variables involved in the drilling and blasting process. For this purpose, we design a computer model based on an Artificial Neuronal Networks (ANN), built by using the most representative variables that come into play with drilling and blasting, such as: the properties of the explosives, the geomechanical parameters of the rock mass, and the design parameters of drilling-blasting. For its experimentation and validation, we have taken the data from a copper mine as reference located in the north of Chile, because of we have the dataset of that ore deposit, which is valid and reliable to evaluate prediction problems based on ANN applied to copper mines. The ANN architecture was of the supervised type, feedforward, with 3 layers and 13 neurons in the only hidden layer, trained with the input data using a dataset with the previously mentioned variables, which then were compared with the breakage results. The model was feed backed in its learning process until it becomes perfected, and is a prediction option that can be used in future blasting of ore deposits with similar characteristics using the same representative variables. Therefore, this is a valid alternative for predicting rock breakage, given that it has been experimentally validated, and has achieved moderately reliable results, providing higher correlation coefficients than traditional models, and with the additional advantage that an ANN model provides, due to its ability to learn and recognize compiled dataset patterns. In this way, using this computer model we can obtain satisfactory results that allow us to predict breakage, providing an alternative for evaluating the costs that this entails.

Ultrasonic measurements are used in civil engineering for structural health monitoring of concrete infrastructures. The late portion of the ultrasonic wavefield, the coda, is sensitive to small changes in the elastic moduli of the material. Coda Wave Interferometry (CWI) correlates these small changes in the coda with the wavefield recorded in intact, or unperturbed, concrete specimen to reveal the amount of velocity change that occurred. CWI has the potential to detect localised damages and global velocity reductions alike. In this study, the sensitivity of CWI to different types of concrete mesostructures and their damage levels is investigated numerically. Realistic numerical concrete models of concrete specimen are generated and damage evolution is simulated using the discrete element method. In the virtual concrete lab, the simulated ultrasonic wavefield is propagated from one transducer using a realistic source signal and recorded at a second transducer. Different damage scenarios reveal a different slope in the decorrelation of waveforms with the observed reduction in velocities in the material. Finally, the impact and possible generalizations of the findings are discussed and recommendations are given for a potential application of CWI in concrete at structural scale.

CoO-ZnO-based composites have attracted considerable attention for the development of energy storage devices because of their multifunctional characterization and ease of integration with existing components. This paper reports the synthesis of CoO@ZnO (CZ) nanostructures on Ni foam by the CBD method for facile and eco-friendly supercapacitor applications. The formation of a CoO@ZnO electrode functioned with cobalt, zinc, nickel and oxygen groups was confirmed by X-ray diffraction, X-ray photoelectron spectroscopy, low and high-resolution of scanning electron microscopy, and transmission electron microscopy. The as-synthesized hierarchical nanocorn skeleton-like structure of CoO@ZnO-3h (CZ3h) electrode delivered a higher specific capacitance of 1136 F/g at a current density of 3 A/g with outstanding cycling stability, showing 98.3% capacitance retention over 3000 cycles in an aqueous 2 M KOH electrolyte solution. This retention was significantly better than that of other prepared electrodes, such as CoO (CO), ZnO (ZO), CoO@ZnO-1h (CZ1h), and CoO@ZnO-7h (CZ7h) (274, 383, 240 and 537 F/g, respectively). This superior capacitance was attributed to the ideal surface morphology of CZ3h, which is responsible for the rapid electron/ion transfer between the electrolyte and electrode surface area. The enhanced features of the CZ3h electrode highlight potential applications in high performance supercapacitors, solar cells, photocatalysis, and electrocatalysis.

Karakoram highway (K.K.H.) the only road link between two countries China and Pakistan. This road network is essential for two countries due to its strategic location and socioeconomic. The highway is more vulnerable due to landslide disasters, especially in rain and snow melting seasons, and different kinds of mass movement activities have occurred along K.K.H., such as rockfall, debris flow, and snow avalanche. The slope stability problems are widespread along with Karakorum (K.K.H.) between Besham city and the Dasu area because of the high seismic zone, rainfall, snow melting, and complex geology slope geometry, week, and adverse discontinuities sets. The detailed fieldwork was done along the Karakorum highway to minimize the risk of slope stability and for planning purposes in Besham to Dasu area and selected nine road-cut slopes. However, in these nine selected roadcut slopes, three slopes were already failed, four slopes are partially stable, and two slopes were stable. Both kinematic and empirical approaches are applied on all these nine road cut slopes and their discontinuities. The kinematic result has shown that all kinds of mode failure such as Toppling, Planar, and Wedge failure mode occurred in these slopes. The RMRb result has shown that all discounters lie in between fair to good rock. Both discrete and continuous (S.M.R.) results show that all discontinuity sets lie between the unstable, partially stable, and stable conditions.

We evaluated the transcriptional response of interferon (IFN)-related genes in rock bream iridovirus (RBIV)-infected rock bream under high-, low-, or no-mortality conditions induced by different stocking water temperatures. Under the high susceptibility condition (group A, water temperature 26 °C, 100% mortality), only the Mx gene was expressed early, with prolonged expression, and with heavy viral loads of approximately 106–107 major capsid protein gene copies/μL from 4 to 10 days post infection (dpi). However, IRF1, IRF3, IRF8, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56 were activated at later time points (8 dpi) and then quickly decreased (10 dpi). For the low susceptibility condition, the water temperature was set at 23 °C for 7 days (group B) and then reduced to 17 °C. Group B exhibited a 28% mortality rate, in which persistent and effective antiviral responses were observed for long periods of time. In particular, at 20 and 22 dpi, when virus replication was peaked at approximately 107/μL, the expressions of most of the IFN-related genes (IRF1, IRF3, IRF8, Mx, STAT1, ISG15, PKR, Viperin, GVIN1, IFI44, and ISG56) were significantly higher in group B than in the control group. Moreover, prolonged and higher levels of IRF3 (at least 30 dpi), IRF8 (at least 30 dpi), ISG15 (at least 30 dpi), PKR (at least 28 dpi), Viperin (at least 30 dpi), and IFI44 (at least 30 dpi) were also observed in the recovery stage of infection. Under the no-susceptibility condition at 17 °C (0% mortality), significantly elevated levels of IRF3, Mx, ISG15, and PKR were observed mostly until 20 dpi. The findings indicate that RBIV infection can induce an efficient IFN-mediated antiviral immune response in low- and no-susceptibility conditions. The findings could be valuable for effective control of viral pathogens in fish.

In rock blasting for mining production, stress waves play a major role in rock fracturing along with explosion gases. Better energy distribution improves fragmentation and safety, lowers production costs, increases productivity, and controls ore losses and dilution. Blast outcomes vary significantly with the choice of the explosive and the properties of the rock mass encountered. This study analyzes the effects of rock mass and explosives properties on the blast outcomes through numerical simulation using data from the case study and later validates the simulation results from the field blast fragmentation. The outcomes suggest that, for a given set of rock properties, the choice of explosive has a major influence on the resulting fragmentation. Strong explosives favor large fracture extents in hard rocks, while less strong explosives offer a better distribution of explosive energy and fractures. The presence of rock structures such as rock con-tacts and joints influences the propagation of stress waves and fractures depending on the structures' material properties, intensity and orientations, and the direction and strength of the stress wave. To achieve effective fragmentation, the blast design should mitigate the effect of variability in the rock mass by ensuring adequate energy distribution within the limits of geo-metrical design.

This paper aims to investigate the coal thickness change area of the combined rock strata energy accumulation law. The method of connecting a uniaxial compression experiment with a theoret-ical analysis is used in this work. We employ a combination of coal and rock to carry out our studies. We investigate how different lithologies and ratios of coal-rock height affect the me-chanical properties of the mixture and the law governing energy accumulation. We have deter-mined the following facts: (1) The combination's peak strength and elastic modulus exceed that of coal and are inferior to that of rock but are nearer to that of coal. (2) When the coal-rock height ratios are dissimilar, the peak strength and modulus of elasticity of the combination show a negative correlation with the coal-thickness share, and the pre-peak energy accumulation and impact energy index of the combination shows a positive correlation with the coal-thickness share. (3) For the combination with the same coal-rock height ratio, the peak strength, elastic modulus, pre-peak energy accumulation, and impact energy index all increase with greater rock strength and elastic modulus. The presence of a hard rock layer affects the accumulation of pre-peak energy. ( 4 ) The stress in the surrounding rock gradually decreases as the coal thick-ness increases. In the area where coal thickness declines, the stress in surrounding rock is higher than that in the region where it thickens. The energy stored in the surrounding rock is directly proportional to the coal in the zone. Conversely, areas with thinner coal deposits exhibit a lower energy storage capacity in the surrounding rock than those with thicker coal deposits. The stress distribution of surrounding rock in coal thickness change is abnormal; substantial energy accu-mulation can swiftly initiate dynamic disasters, such as rock bursts. This study has important reference significance for preventing and controlling rock burst in coal thickness change areas.

The surrounding rock during the coal mine excavation is prone to significant engineering disasters such as considerable deformation and rockbursts. Pressure release can improve the stress field of a deep rock mass and prevent the occurrence of dangers such as roadway collapse and coal and gas outbursts. This paper uses the ANSYS/LS-DYNA finite element software to simulate the crush area and fracture zone of a detonation charge with different diameters under in-situ stress. The stability of the surrounding rock was analyzed based on the impact stress and velocity, and was verified by field tests. The research results show that the blasting load primarily affects the damaged area near the borehole, while the in-situ stress affects the far-field crack propagation. The crack propagates in the direction of high surrounding rock pressure. When the uncoupling index is 1.5, the impact pressure of the 60 mm diameter cartridge is 8 times that of the 20 mm diameter cartridge. The impact speed can reach 2 times that of the 20 mm diameter cartridge. The high-energy event of the roof is transferred to the front of the working face, the distribution is no longer concentrated, and a better blasting pressure relief effect is achieved. The research results can help guide the prevention and control measures of rock bursts and other mining disasters.

Fractures are present in hydrocarbon reservoirs of different porosity ranges. Seismic anisotropy has been widely used in fracture characterization and shown to be sensitive to background matrix porosities in theoretical studies. An understanding of the effects of background porosity on seismic anisotropy could improve seismic characterization in different fractured reservoirs. Based on synthetic rocks with controlled fractures, we conducted laboratory experiments to investigate the influence background porosity has on P wave anisotropy and shear wave splitting. A set of rocks containing the same fracture density (0.06) with varying porosities of 15.3%, 22.1%, and 30.8% were constructed. P and S wave velocities were measured at 0.5 MHz as rocks were water saturated. Results show that when porosity increased from 15.3% to 22.1%, P wave anisotropy and shear wave splitting exhibit slight fluctuations. However, when porosity continued to increase to 30.8%, P wave anisotropy declined sharply while shear wave splitting stayed nearly constant. The measured results were compared with predictions from equivalent medium theories. Qualitative agreements were found between theoretical predictions and measured results. In Eshelby-Cheng model, the increase of porosity reduces the fracture-induced perturbation in the fracture normal direction, resulting in a lower P wave anisotropy. In Gurevich(2003) model, the increase of porosity can reduce the compressional stiffness in parallel direction to a larger extent than that in perpendicular direction, thus leading to lower P wave anisotropy.

Rock salt is characterized by specific geomechanical and rheological properties. Layers of rock salt on depth over 900 m cause problems with shaft lining deformation. Methods of shaft lining protection used so far (e.g. in Sieroszowice mine) have not been effective enough. The research presents a patented and copyright protected concept of a shaft lining construction that can be used in rock masses with strong rheological properties and susceptible to leaching. In the case of salt layers, especially at significant depths the relative convergence of the heading contour may be about 40 ‰/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, is not sufficient to ensure the stability of the shaft guidance geometry. In the new shaft lining concept, the excessive rock creep into the outbreak inside the shaft diameter is removed by local and controlled leaching of the shaft cheeks by means of fresh water through a porous medium at the contact layer behind the watertight tubing lining. The article presents the methodology of performing tests on a special device and the test results.

A single paragraph Arbuscular mycorrhizal fungi (AMF) establish symbiotic relationships with many crops. These soil microbiotas improve the soil fertility through the soil physical, chemical and biological properties. extending the root absorbing area. In return, the symbiont receives plant carbohydrates for the completion of its life cycle. AMF also helps plants to cope with biotic and abiotic stresses such as extreme temperature, heavy metal, diseases, and pathogens. For soil physical properties, the mechanisms used by AMF are the production of a glycoprotein, glomalin, which creates a high quality of soil macro-aggregations. These macro-aggregations control soil erosion, nutrients and organic matter losses. For soil chemical properties, AMF produce acids and an enzyme called phosphatase. This enzyme hydrolyzes the inorganic phosphorus and the rock phosphate (RP) hence making P available in the soil for plant uptake. AMF also are involved in soil nitrogen, carbon and trace element cycling. Regarding the biological component of the soil, AMF influence the composition, diversity and activity of microbial communities in the hydrosphere. They also work in synergy with others soil microorganisms to improve soil fertility, plant growth and resistance against some diseases. In this review, we present the contribution of AMF on soil fertility and importance in polluted soils.

Uranium isotopes actively investigated as mechanistic or time scale tracers of natural processes. This paper describes the occurrence and redistribution of U in the Vendian aquifer of the paleo valley at NW Russia. Forty-four rock samples were collected from boreholes, and twenty-five groundwater samples. The U, Fe concentration, and 234U/238U activity ratio were determined in the samples. We estimated the 14C and 234U-238U residence time of groundwater in an aquifer. It has been established that the processes of chemical weathering of Vendian deposits led to the formation of a strong oxidation zone, developed above -250 m.a.s.l. The inverse correlation between the concentrations of uranium and iron is a result of removal of U from paleo valley slopes in oxidizing conditions and accumulation of U at the bottom of the paleo valley in reducing conditions, and accumulation of Fe on the slopes and removal from bottom. Almost all U on the slopes replaced by a newly formed hydrogenic U with a higher 234U/238U activity ratio. After that dissolution and desorption of hydrogenic U was occurred from the slopes during periods without any glaciations and marine transgressions. Elevated concentrations of U preserved in not oxidized lenses at the paleo valley bottom.

High-efficiency rock breaking by hydraulic jetting is the key to radial horizontal drilling technology. In order to improve the drilling efficiency of hydraulic jet rock breaking in radial horizontal wells, based on LS-Dyna display dynamics, a numerical simulation model of single nozzle jet rock breaking is established to analyze the influence of different nozzle parameters on rock breaking effect. Then, the numerical simulation model of the spin multi-nozzle jet bit is established, and the influence of different rotation speeds on the rock breaking effect of the jet bit is analyzed. Finally, the rock breaking drilling characteristics of the spin multi-nozzle jet bit and the conventional multi-nozzle jet bit are compared and analyzed. The results show that when the jet impacts the rock surface, the larger the inclination angle is, the larger the rock breaking width formed by the jet is. The smaller the dip angle, the greater the rock breaking depth. When the inclination angle is greater than 60 °, it is difficult to meet the needs of reaming. The width and depth of the nozzle gradually increase with the increase of the diameter. When the nozzle diameter is greater than 1.3mm, the growth rate of rock breaking depth begins to decrease. The optimum nozzle diameter is 1.3 mm. When v = 50m / s, the damage caused by the jet to the rock surface is very small, because the condition of rock fracture is not reached at this time. This shows that there is a critical value of the water jet impact velocity, and only when the velocity is reached, the rock will break. When the velocity is v = 150m / s, v = 200m / s, v = 250m / s, v = 300m / s, the rock breaks. At the same time, the higher the speed, the higher the degree of rock fracture, the greater the fracture depth, the greater the fracture area, the better the fracture effect. The tangential and radial velocity of the jet increases the shear and tensile failure rate of the sample, and improves the rock breaking efficiency of the jet, which has certain guiding significance for improving the rock breaking drilling efficiency of radial horizontal well drilling.

Abstract The expression patterns of microRNAs (small non-coding RNAs) are altered in many biological processes such as myogenesis. In this study, we aimed to investigate the impact of predicted miR-202, its target genes Akt2 and Rock-1 as a potential regulator of myoblast in the myocyte differentiation process using the C2C12 cell line. After confirmation of the differentiation process induced by 3% horse serum, the expression level of miRNA and its targets were evaluated. In the following, a luciferase assay was conducted to approve the effect of miRNA on its target. Our results indicated that miR-202 and Akt2 were significantly up-regulated during differentiation, while Rock-1 was downregulated. Co-transfection of miRNA with psiCHECK2-Rock-1 significantly presented that Rock-1 was directly targeted by miR-202. On the contrary, miR-202 has failed to enforce its inhibitory effect on Akt2 expression. In particular, miR-202 seems to be a regulator of muscle differentiation pathway thought targeting Rock-1.

The formation of rock fractures in nature has a certain relationship with water seepage. In order to analyze the shape of rock fracture, we propose a rock deformation theoretical model in three-dimensional space considering with the condition of seepage water pressure, and establish the mass conservation equation, seepage equation, surrounding rock displacement equation, so as to deduce the rock deformation control equation under seepage pressure action. The numerical analysis of the nonlinear quadratic partial differential equation obtains the fracture deformation distribution in the example, and verifies with the calculated fracture morphology. And we further use this principle to analyze the fracture morphology in nature and prove the rationality of the theory.

This paper concerns the effect of proppant embedment related with hydraulic fracturing treatment. This phenomenon occurs if the strength of the reservoir rock is lower than proppant grains. The aim of the research is laboratory determining the loss of width of the proppant pack built of light ceramic grains. The laboratory simulation of the embedment phenomenon was carried out for a shale rock on a hydraulic press, in a specially prepared for this purpose a heated embedment chamber. Tests were conducted at high temperature and axial compressive stress conditions. The surfaces of the cylindrical core plugs (fracture faces) were imaged under an optical microscope equipped with 3D software. The fracture faces were examined and compared before and after the embedment phenomenon. The analysis of the obtained images of the fracture face were made based on the research method of the embedment phenomenon developed at Oil and Gas Institute-NRI. On the basis of laboratory tests, the parameters characterizing the embedment phenomenon were collected and discussed. In addition, the percentage reduction in the width of the proppant pack was determined.

Cemented rock fill (CRF) is commonly used in cut-and-fill stoping operation in underground mining. This allows for the maximum recovery of ore. Backfilling can improve stope stability in underground workings, and then improve ground stability of the whole mine site. Backfilling step scenarios vary from site to site. This paper presents the investigation of five different backfilling step scenarios and their impacts on the stability of stopes at four different mining levels. A comprehensive comparison of displacements, major principal stress and stress concentration factor (SCF) was conducted. The results show that different backfilling step scenarios have little influence on the final displacement for displacement in the stopes. Among the five backfilling scenarios, the major principal stress and stress concentration factor (SCF) have almost the same final results. The backfilling scenario SCN-1 is the optimum option among these five backfilling scenarios. It can immediately prevent the increase of the displacement and reduce the sidewall stress concentration, thereby preventing possible failures. Using the same strength of CRF can achieve same effects among the four mining levels. Applying backfilling CRF of the same strength at different mining depths is acceptable and feasible to improve the stability of the stopes.

The issue of monitoring and early warning of rock instability has received increasing critical attention in the study of rock engineering. To investigate the damage evolution process of granite under triaxial compression tests, acoustic emission (AE) tests were performed simultaneously. This study firstly introduced two novel parameters, i.e., the coefficient of variation (CoV) of the information entropy and correlation dimension of the amplitude data from the AE tests, to identify the precursor of the failure of granite. Then the relationship between the changes in these parameters and the stress-time curve was compared and analyzed. The results of this study show that: (1) There is a strong correlation between the CoV of the information entropy and the failure process of granite. The granite failed when the CoV curve raised to a plateau. (2) The fluctuation of the correlation dimension indicates the different stages of the loading process, i.e., the initial compaction stage, the linear elastic stage, the yield stage, and the failure stage. Each stage contains a descending and a rising process in the correlation dimension curve, which indicates that this parameter could be used to identify the precursor of the failure as well. (3) The combined analysis of the two can improve the accuracy of rock instability prediction. This study provides new insights into the prediction of rock instability, which has theoretical implications for the stability of subsurface engineering rock masses.

Poor survival of human pluripotent stem cells (hPSCs) following freezing, thawing, or passaging hinders maintenance and differentiation in stem cell research. Rho-associated kinases (ROCKs) play a crucial role in hPSC survival. To date, a typical ROCK inhibitor, Y-27632, has been the primary agent used in hPSC research. Here, we report that another ROCK inhibitor, fasudil, can be used as an alternative. Fasudil increased hPSC growth due to survival rather than proliferation following thawing and passaging, similar to Y-27632. It did not affect pluripotency and genetic integrity including mitochondrial genome (mtDNA). Notably, the genes related to metabolism, mTORC1, and TP53 have mainly displayed a faster recovery pattern with ROCK inhibitors than control. Furthermore, fasudil was confirmed as useful for the single dissociation of hPSCs and for aggregation. It also increased retinal pigment epithelium (RPE) differentiation and the survival of neural crest cells during differentiation. These findings suggest that fasudil can replace Y-27632 for use in stem cell research.

The use of salt rock for underground radioactive waste disposal facilities requires a comprehensive analysis of creep-damage process in salt rock. A computer-controlled creep setup is employed to carry out a creep test of salt rock lasted as long as 359 days under a constant uniaxial stress. The AE space-time evolution and energy releasing characteristics during creep test are studied in the meantime. A new creep-damage model is proposed on the basis of fractional derivative by combining the AE statistical regularity. It indicates that the AE data in non-decay creep process of salt rock can be divided into three stages. Furthermore, the parameters of new creep-damage model are determined by Quasi-Newton method. The fitting analysis suggests that the creep-damage model based on fractional derivative in this paper provides a precise description of full creep regions in salt rock.

The Cancer Genome Atlas (TCGA) has classified papillary thyroid carcinoma (PTC) into indolent RAS-like and aggressive BRAF-like based on its distinct driver gene mutations. This study aimed to assess clinicopathology and pERK1/2 expression variations between BRAF-like and RAS-like PTCs and establish predictive models for BRAFV600E and RAS-mutated PTCs. A total of 222 PTCs underwent immunohistochemistry staining to assess pERK1/2 expression and Sanger sequencing to analyze the BRAF and RAS genes. Multivariate logistic regression was employed to develop prediction model. Independent predictors for the BRAFV600E mutation include a nuclear score of 3, the absence of capsules, an aggressive histology variant, and pERK1/2 levels exceeding 10% (X2=0.128, P>0.05, AUC=0.734, P<0.001). RAS mutation predictive model includes follicular histology variant and pERK1/2 expression >10% (X2=0.174, P>0.05, AUC=0.8, P<0.001). We proposed using the prediction model concurrently with four potential combination group outcomes. PTC cases included in combination of low BRAFV600E-scoring group and high RAS-scoring group are categorized as RAS-like (adjOR=4.857, P=0.01, 95% CI=1.470-16.049). PTCs included in combination of high BRAFV600E-scoring group and low RAS-scoring group are categorized as BRAF-like PTCs (adjOR=3.091, P=0.001, 95% CI=1.594-5.995). The different prediction models indicate variations in biological behaviour between BRAF-like and RAS-like PTCs, necessitating adjustments in treatment approaches.

Toll-like receptors (TLRs) play a key role in the innate immune response to numerous pathogens, including Acanthamoeba sp. The aim of this study was to determine the expression of TLR2 and TLR4 in the eyes of mice following intranasal infection with Acanthamoeba sp. Amoebae used in this study were isolated from the bronchial aspirate of a patient with acute myeloid leukemia (AML) and atypical symptoms of pneumonia. We found statistically significant differences in the expression of TLR2 and TLR4 in the eyes of immunocompetent mice at 8, 16, and 24 days post Acanthamoeba sp. infection (dpi) compared to control. Immunosuppressed mice showed significant differences in the expression of TLR2 at 16 and 24 dpi compared to uninfected animals. Our results indicate that TLR2 and TLR4 are upregulated in the eyes of mice in response to Acanthamoeba sp. We suggest that it is possible for trophozoites to migrate through the optic nerve from the brain to the eyes.

In recent years, the term quantum-like has been increasingly used in different disciplines, including neurosciences, psychological and socio-economical disciplines, claiming that some investigated phenomena show “something” in common with quantum processes and, therefore, they can be modeled using a sort of quantum formalism. Therefore, the increasing use of the term quantum-like calls for defining and sharing its meaning in order to properly adopt it and avoid possible misuse. In our opinion, the concept of quantum-like may be successfully applied to macroscopic phenomena and empirical sciences other than physics when at least two conditions are satisfied: a) the behavior of the investigated phenomena show logical analogies with quantum ones; b) it is possible to find a criterion of truth based on an experiential/scientific approach applied to a probabilistic model of description of the phenomena. This is only a first, small step in the approach to the concept of quantum-like, hopefully helpful to promote further discussion and achieve a better definition.

Identification and segmentation of rock particles is very important in geology, mining, engineering construction, and environmental monitoring. Traditional methods for recognizing the rock particle characteristics are time-consuming, labor-intensive, and limited by the geographical scope of the sampling sites, which makes it more difficult to represent the spatial distribution of the rock particles accurately. Recent advancements in deep learning techniques offer promising solutions to automate this process. This study aims at utilizing state-of-the-art (SOTA) Mask R-CNN deep learning algorithm from the Detectron2 framework, to capture global features of rocks that will enable the recognition of rock particles more efficiently, just from having the rock images. These images are subject to image processing techniques such as a Gaussian filter, to denoise and smoothen the image, and an Illumination Adaptive Transformer (IAT) framework, to adjust the lighting exposure; all of which add to improve the quality of the image dataset. Afterward, the Mask R-CNN and Detectron2 models are utilized in training the images using transfer learning. Experimental results from evaluating the performance of the proposed algorithms showcase the effectiveness of the approach, thereby highlighting its potential to revolutionize rock particle segmentation across various domains.

Based on the analysis of hydrochemical data of 18 samples of shallow groundwater around Hancheng mining area in Guanzhong Basin, Gibbs semi-logarithmic diagram and Piper diagram were used to study the hydrogeochemical behavior of shallow groundwater around Hangcheng mining area in Guanzhong Basin. Chemical composition analysis showed that most of the groundwater was SO₄ · Cl-Ca · Mg type, accounting for 61.1 %. Hydrogen and oxygen isotope data show that groundwater in the study area is recharged by modern precipitation. The main chemical components of most groundwater are Ca²⁺, Mg²⁺, HCO₃^-, Cl^-and SO₄^2-. Ca²⁺, Mg²⁺, and HCO₃^- are mainly dolomite, calcite, and gypsum dissolution precipitation results. Na⁺ and Cl^- originate from the dissolution of halite. The main ion chemistry of shallow groundwater in this area is controlled by rock weathering, and pyrite oxidation is an important factor affecting SO₄^2-concentration. The research results will help analyze the formation mechanism of chemical components and provide some basic data for the evolution of mine water in this area in the future.

In order to study the influence of falling rock shape on its rolling characteristics and realize the optimization of falling rock protection design, the following research was carried out. Design model experiments to explore the rolling characteristics of different shapes of rockfalls. Based on the experimental results, it was found that the slenderness ratio, center of gravity, and rotational inertia of the rockfalls can affect their rolling characteristics, leading to swaying and changing the rolling axis during the rolling process, thereby affecting their rolling speed. On this basis, the formation mechanism of rolling resistance is analyzed, and the main cause of energy loss is the rolling resistance arm formed with the rolling surface during rockfall rolling, and a shape parameter to quantify the rolling resistance is proposed. The parameters are substituted into the kinematic formula, in which the influence of the rockfall shape, slope and slope roughness on the rolling speed is considered. Combined with the offset and initial position of the rockfall, the formula can be used to calculate the rolling speed and impact energy in the rolling region and any position in the region. The calculation formula was validated using model experimental data, and the results showed that the error between the experimental and calculated values was small. The error was corrected based on the experimental data. After on-site testing and verification, it can provide reference for the management of rockfall disasters.

The study seeks to unravel the intricate operational sequence involved in preparing prehistoric pigments for rock art within the Puerto Roque rock art shelter. Sixteen pigment samples, identified as Lab Code Puerto_1 to Puerto_16, were meticulously collected from specific figurative representations. Additionally, three ochre samples (Puerto_17, Puerto_18, and Puerto_19) were sourced from the shelter's soil. Employing a comprehensive multi-analytical approach, including Raman microspectroscopy, X-ray microfluorescence (EDxrf), Fourier-transform Infrared spectroscopy (ATR-FTIR), and Scanning Electron Microscopy (SEM), all nineteen samples underwent thorough analysis. The research unveiled a spectrum of distinct red pigments within the rock art depictions. The sampling strategy for the 16 panels in the Puerto region was meticulously designed to capture the diverse array of rock art manifestations, each presenting unique characteristics that warranted detailed scientific investigation. The selection of these panels was guided by the recognition of various artistic techniques employed in the creation of the paintings, the nuanced hues exhibited, prevalent erosion issues, potential effects of sunlight exposure, and the intriguing hypothesis of distinct chronological periods due to several superimpositions detected. Notably, darker pigments in samples Puerto_02, Puerto_10, and Puerto_19 revealed a composition of hematite with the added presence of carbon. Meanwhile, Puerto_08 exhibited an orange hue primarily composed of goethite. Bright red pigments in samples Puerto_01, Puerto_03, Puerto_05, Puerto_07, Puerto_09, and Puerto_11 were predominantly characterised by hematite, as confirmed by Raman analysis. EDxrf analysis demonstrated an elemental composition akin to the three ochre pieces examined. Furthermore, ATR-FTIR spectroscopy suggested the potential influence of a heating process in enhancing red coloration, corroborated by spectral results from specific samples. This finding aligns with prior research, underscoring the technological sophistication embedded in early artistic endeavours. The detailed understanding of pigment types and their preparation methods provides insights into the artistic choices and technological adeptness of prehistoric communities. Beyond the archaeological implications, these findings contribute significantly to the ongoing conservation efforts of rock art sites. The amalgamation of diverse analytical techniques showcased their efficacy in elucidating the intricate world of pigment preparation. Recognizing the unique microclimates at each rock art site that influence pigment preservation, this localised approach aids informed decisions in safeguarding these invaluable cultural resources. In essence, this study not only unravels the artistic past but also advocates for the sustainable conservation of our shared cultural heritage.

The recognition of coal-rock interface is very crucial for the research in the intelligent production of coal mine. This study investigates the application of terahertz time-domain spectroscopy in the recognition of coal-rock interface, including the identification of coal-rock and coal-rock mixtures, as well as the accurate characterization of coal seam thickness. Terahertz detection was used to obtain the optical parameter information of the pressed pellets prepared by mixing two different kinds of coal and two kinds of rock. Based on the experiment results, the database was established for the identification of coal-rock interfaces in coal mining machines. The terahertz detection was performed on 10 different kinds of sheet anthracite with different thickness, and the terahertz spectra of coal seams with different thickness were simulated and calculated by using simulation software, which can accurately obtain the thickness of coal seams and provide effective mining thickness parameters for coal seam mining. Through the experiment and simulation, the terahertz time-domain spectroscopy technology has a promising application prospect in the identification of coal-rock interface.

A single geological carbon dioxide (CO2) storage within salinity aquifer as a paramount stratagem in the context of forthcoming CO2 sequestration initiatives. Within the expansive tapestry of terrestrial salinity aquifers in China, replete with nuances in mineral composition and structural diversity, a paradigm distinct from the marine sedimentary basins of North America, a labyrinthine stratigraphic environment of elevated complexity unfolds. Consequently, conspicuous lacunae and insufficiencies manifest within the existing knowledge reservoir pertaining to CO2-water-rock (mineral) reaction mechanisms. Notably, a conspicuous dearth of insights prevails concerning the dissolution kinetics inherent to individual minerals embroiled in these reactions. The present investigation undertakes a scrupulous exploration into the dissolution and erosive processes manifest within four emblematic terrestrial minerals in conjunction with CO2. Furthermore, the study meticulously scrutinizes the evolution of ionic composition and pH within the formation water throughout the trajectory of the geochemical reactions. To accomplish this, a simulation apparatus is configured to emulate conditions germane to temperature, pressure, and mineralization characteristics characteristic of a prototypical salinity aquifer reminiscent of the Daqing oilfield in China. The findings that emerge from this scrutiny reveal that the erosive action of CO2 fluid begets varying degrees of dissolution within the four minerals under investigation. Moreover, our meticulous inquiry lays bare that, in the terminal phases of the reaction process, feldspar precipitates secondary minerals, characterized primarily by dawsonite, in response to the aquatic milieu typifying the profound salinity stratum of terrestrial sedimentation. This milieu is notably enriched with Na+ ions and NaHCO3. This phenomenon suggests that feldspar, under these specific conditions, assumes the mantle of a mineral amenable to carbon sequestration, thus enriching the reservoir for CO2 mineralization within the salinity stratum of terrestrial sedimentation.

Enhanced oil recovery (EOR) refers to the various techniques used to increase the amount of crude oil that can be extracted from an oil field. These techniques are used after the primary and secondary recovery methods have been depleted. There are three main types of EOR: thermal, gas injection, and chemical. EOR techniques can be expensive and complex, but they can help to recover additional oil that would otherwise be left in the reservoir. EOR can also extend the life of an oil field and increase the overall production from a given field. The parameters affecting oil recovery are a major concern in EOR systems, and these parameters need more consideration with the factors affecting them. In this study, the influence of permeability variations on fluid flow in a sandstone reservoir was explored, as well as an up-to-date description of three states of EOR with thorough explanations of the methods utilized and the mechanisms driving their oil recovery application. The difficulties encountered in the use of the different standard EOR Mechanisms were noted, and solutions to these difficulties were proposed. Furthermore, the contemporary trend of adding nanotechnology and its synergistic effects on the stability and efficiency of traditional chemicals for EOR were examined and analysed. Finally, laboratory findings and field initiatives were discussed. The review went into detail about the transport of nanoparticles across reservoirs, as well as the evaluation of EOR, mobility ratio, and fluid displacement efficiency. This review provides thorough information on the uses of improved oil recovery mechanisms for sustainable energy production.

The rock strata movement deformation generated by the mining process of the mine will inevitably lead to surface subsidence and a series of environmental hazards, so it is particularly important to monitor the rock strata movement deformation and surface subsidence in the goaf area. With the development of surface subsidence monitoring technology, InSAR technology has been widely used in the research of surface subsidence in mining areas with the advantages of high precision and wide monitoring. In this paper, by obtaining the image data of 59 Sentinel-1A scenes in the mining area, the obtained PS points were analyzed and processed by ArcGIS difference analysis by PS-InSAR technology, and the surface deformation cloud map and settlement curve of the mining area in various periods were obtained, and the rock strata movement deformation and surface subsidence law of the goaf before treatment and after different treatment methods were studied by influencing factors such as stope layout and mining depth. The results show that the rock strata movement deformation and surface subsidence degree of the goaf under different treatment methods are different due to different influencing factors, and their positions also change dynamically with time. Applying InSAR technology to study rock strata movement deformation and surface subsidence can provide an important basis for mine safety mining, goaf treatment, rock strata movement deformation and surface subsidence monitoring.

For the Altai mountainous region, especially the arid south-eastern part, the history of glacier fluctuations in Pleistocene and Holocene is still poorly known. The key plots were located in the Kargy valley (2288-2387 m a. s. l.) that is not currently affected by glaciations. The relative dating method was applied to define Pleistocene moraine chronology and configuration in the Kargy valley. Taking into account that relative dating methods are primarily based on weathering pat-terns, the mineralogy, porosity, and specificity of biological colonization as an agent of weath-ering were obtained for the moraine samples. Three moraine groups of different age (presumably MIS 6, MIS 4, and MIS 2) were identifies based on detailed investigation of morphological features. The moraine age was indirectly confirmed by the mesostructure of the moraine samples repre-sented by fine-grained shale: the older sample is characterized by a more developed fractal sur-face than the younger one. The growth of biota (crustose lichen and micromycetes) leads to initial biomass accumulation and subsequent rock disintegration. The accumulation of autochthonous fine earth on the rock surface was considered the initial stage of fine earth formation affected by biota.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

The degree of ore rock fragmentation of mine blasting is an important index for evaluating the effect of engineering blasting. In order to study the effect of millisecond delayed blasting on the internal fragmentation of the ore rock, LS-DYNA numerical simulation software was used to obtain the damage characteristics of the ore rock in the blasting area using the RHT model. The Mohr-Coulomb strength damage criterion was applied to analyze the internal stress state of the ore rock, and the effects of 25ms, 50ms and 75ms delay time conditions on ore rock fragmentation were studied. The results show that, within a certain range of delay time, the degree of rock fragmentation increases with the increase of delay time. The stress state in the ore rock due to blasting is strengthened with the increase of delay time in the direction of the blast hole, which shows that the stress concentration is strengthened from the excavation face to the interior of the ore rock. The damage and the degree of fragmentation show a characteristic relationship of 25ms＜50ms＜75ms, which is verified by carrying out blasting experiments on site.

The rapid retreat of coastal cliffs poses a profound risk to property, transport infrastructure and public safety both in Ireland and globally. This study combines historical data (maps and orthophotos, 1842 to 2000) with contemporary UAV surveys (2019 to 2023) to quantify cliff top and cliff face retreat along a 250 m wide coastal drumlin at Silverstrand in Galway Bay, Ireland. Retreat rates for the cliff top and cliff face were calculated using 2D mapping and 3D modelling, respectively. Critically, the choice of method appears to have a major impact on apparent rates of cliff top retreat, with output from the 2D mapping approach (0.14 +/- 0.02 m yr-1) being double that of the 3D modelling approach (0.08 +/- 0.02 m year-1). The aperiodic development of a talus cone, which offers temporary protection to the cliff from storm waves, also influences the estimation of cliff retreat. The repeat cycles of talus slope formation and removal in this high wave energy climate suggest that the drumlin transitions between a periodically transport-limited system and supply limited system over short- and long-time periods, respectively, on the continuum of cliff types. These results warrant further research to identify and quantify the rates, patterns, drivers (marine and subaerial processes), and timing of cliff retreat rates in response to climate change.

The wettability of the oil-brine-rock systems is very challenging mainly for the carbonate reservoirs and it plays a significant role to enhance the oil recovery (EOR). Carbonate rocks are mad-up of complex lithology, hence these requires careful treatments in controlling their wetting behavior for enhanced oil recovery. Therefore, it is extremely important to modify their wettability from an oil-wet rock behavior to a water-wet so that the residual oil can be produced efficiently. Thus, the present study has examined the effectiveness of alumina nanofluid as well as a new chemical methyl blue to alter the wettability. The methyl blue is released on massive scale from various industries i.e. pharma, textile and food industry which is a key environmental concern which contaminates the water table. Hence the study, explores the effects of MB and alumina nanofluid on the wettability. The effect of nanofluids formulated via dispersing the alumina nanoparticles in aqueous solutions at various concentration (0. 0.05, 0.3, 0.50, 0.75 and 1.0 wt. %) were tested for wettability modification under different physio-thermal conditions. Subsequently, the wettability change was examined for the samples treated with different concentrations of MB (10, 15, 30, 50 and 100 mg/L) for 7-days at two different temperatures of (25 and 50 0C). The results showed that hydrophobicity of the SML carbonate rock has significantly reversed while treating with alumina nanofluids and MB. Thus, the wettability modification/reversal via treatment of MB and alumina nanofluid can be an effective mechanism to hydrogen injection and for EOR processes.

In this work, some micro-samples belonging to the open-air rock art site of Cueva de la Vieja (Alpera, Albacete, Spain) were analysed. These samples were collected after and before a desalination treatment carried out with the aim of removing a whitish layer of concretion that affected the painted panel. The diagnostic study was performed to study the conservation state of the panel and then to confirm the effectiveness of treatment. Micro energy dispersive X-ray fluorescence spectrometry, Raman spectroscopy and X-ray diffraction were employed for the characterization of the degradation product as well as that of mineral substrate and pigments. The micro-samples analysis demonstrated that the painted layer was settled on a dolomitic limestone with silicon aggregates and aluminosilicates as well as iron oxides. The whitish crust was composed by sulfate compounds like gypsum (CaSO4·2H2O) with minor amount of epsomite (MgSO4.7H2O). An extensive phenomenon of biological activity was demonstrated since, in almost all the samples analysed, the presence of calcium oxalates monohydrate (CaC2O4H2O) and dehydrate (CaC2O42H2O) were found. Probably the presence of both calcium oxalates had favoured the conservation of pictographs. In addition, some carotenoids pigments, scytonemin (C36H20N2O4) and astaxanthin (C40H52O4) were characterized both by Raman spectroscopy and by X-ray diffraction. Hematite was found as a pigment voluntarily used for the painting of the panels used in mix with hydroxyapatite and amorphous carbon. The results of the analyses of the samples taken after the cleaning treatment confirmed a substantial decrease in sulphate patina on the panel surface.

With the rapid development of urbanization, the chemical evolution of groundwater is significantly affected by human activities. However, the driving mechanisms of groundwater chemical evolution at different stages of urbanization remain unclear, severely impacting the implementation of groundwater protection. This study investigated the driving mechanisms of groundwater chemical evolution based on the long-term series (from 1985 to 2015) of hydrochemical data from 19 groundwater monitoring sites in rapidly urbanizing areas (Shijiazhuang, Hebei Province, China). The results show that the concentrations of various chemical components in groundwater gradually increase with the acceleration of urbanization process, especially NO3-, which has increased from 13.7 mg/L in the primary stage of urbanization (PSU) to 65.1mg/L in the advanced stage of urbanization (ASU), exceeding the WHO drinking water standard (50mg/L), indicating that the groundwater chemistry has been significantly affected by human activities. It is interesting to find that the main hydrochemical types have changed from HCO3•SO4-Ca•Mg type water in the PSU to SO4•HCO3-Ca•Mg type water in the ASU. It is worth noting that there were obvious differences in driving factors of groundwater chemical evolution at different urbanization stages. In the PSU, the driving factors of groundwater chemical evolution were carbonate and rock salt dissolution, cation exchange, and industrial activities. However, in the intermediate stage and advanced stage, the driving factors of groundwater chemical evolution were changed to carbonate and gypsum dissolution, groundwater over-exploitation, agricultural fertilization, and domestic sewage. Based on the above conclusions, it is suggested that future groundwater management should control the amount of agricultural fertilizers, apply scientific fertilization, and prohibit the discharge of various types of non-compliant sewage, while strengthening the supervision of groundwater extraction to reduce the impact of urbanization development on the groundwater chemical evolution process.

During the last few years, several approaches have been proposed to improve early warning systems for reducing rock-fall risk. In this regard, this paper introduces a Deep learning-and (IoT) based Framework for Rock-fall Early Warning, devoted to reducing the rock-fall risk with high accuracy. In this framework, the prediction accuracy was augmented by eliminating the uncertainties and confusion plaguing the prediction model. In order to achieve augmented prediction accuracy, this framework fused the prediction model-based deep learning with a detection model-based Internet of Things. In order to determine the framework’s performance, this study adopted parameters, namely overall prediction performance measures, based on a confusion matrix and the ability to reduce the risk. The result indicates an increase in prediction model accuracy from 86% to 98.8%. In addition, a framework reduced the risk probability from (1.51 ×10-3) to (8.57 ×10-9). Our results indicate the framework’s high prediction accuracy; it also provides a robust decision-making process for delivering early warning and lowering the rock-fall risk probability.

Rocks are materials with a wide variety of structures and properties. These can be unprocessed conglomerates of conglomerated minerals as well as crystallized outcrop or metamorphic rocks. Their processing, especially shaping, poses many technological difficulties. Therefore, it is very important to answer the question of how these natural materials yield to high-pressure water jet and abrasive water. It is equally important to determine the effect of key process parameters such as pressure, water nozzle diameter and feed rate on cutting efficiency. The first two parameters determine the water output and power of the jet, while the third determines the jet erosion time per unit volume of material. Their interdependence, using appropriate evaluation indicators, allows to determine the energy intensity of processing and directions for its minimization.

In order to understand the impact of lithologic heterogeneity of continental mixed fine-grained sedimentary rocks on reservoir brittleness in western Qaidam basin, the mechanical properties of the rocks and their correlation with mineral composition and petrographic characteristics were studied by measns of mineralogy, petrography and triaxial stress test. The results show that the reservoir rocks can be divided into 5 different types according to the mechanical properties of the reservoir (characteristics of stress-strain curves), among them Type I and III belong to similar elastoplastic failure model, type II shows a special pulse failure mode for plastic material, type IV shows a failure mode of mixed characteristics, and type V exhibits a typical plastic failure model. The correlation between minerals and mechanical properties indicates that quartz and feldspar, which are often considered brittle minerals, do not contribute much to the brittleness of continental fine-grained sedimentary rocks. The main minerals affecting reservoir brittleness are dolomite and clay minerals, and their contributions to reservoir brittleness are positive and negative, respectively. The petrographic analysis results prove that the abnormal correlation between rock mechanical properties and quartz and feldspar is caused by the different rock fabrics. When dolomite forms a rock skeleton, it typically exhibits greater strength, brittleness and physical properties than other minerals. Based on the results, a brittleness evaluation standard for continental fine-grained sedimentary rock reservoir is proposed, and the validity of the standard is verified by the spatial correlation between the lithology probability model and the micro-seismic monitoring data, indicating that the spatial heterogeneity of dolomite-rich rock is the main controlling factor for the development of ‘sweet spot’ in the Cenozoic continental fine-grained sedimentary rock reservoir in the Western Qaidam Basin.

The efficacy of predicting geochemical parameters with a 2-chain workflow using spectral data as the initial input is evaluated. Spectral measurements spanning the approximate 400-25000nm spectral range are used to train a workflow consisting of a non-negative matrix function (NMF) step, for data reduction, and a random forest regression (RFR) to predict 8 geochemical parameters. Approximately 175000 spectra with their corresponding chemical analysis were available for training, testing and validation purposes. The samples and their spectral and chemical parameters represent 9399 drillcore. Of those, approximately 20000 spectra and their accompanying analysis were used for training and 5000 for model validation. The remaining pairwise data (150000 samples) were used for testing of the method. The data are distributed over 2 large spatial extents (980 km2 and 3025 km2 respectively) and allowed the proposed method to be tested against samples that are spatially distant from the initial training points. Global R2 scores and wt.% RMSE on the 150000 validation samples are Fe(0.95/3.01), SiO2(0.96/3.77), Al2O3(0.92/1.27), TiO(0.68/0.13), CaO(0.89/0.41), MgO(0.87/0.35), K2O(0.65/0.21) and LOI(0.90/1.14), given as Parameter(R2/RMSE), and demonstrate that the proposed method is capable of predicting the 8 parameters and is stable enough, in the environment tested, to extend beyond the training sets initial spatial location.

Purpose: This study investigated the hypotensive effect of RKI-1447, a Rho kinase inhibitor, in a porcine ex vivo pigmentary glaucoma model. Methods: Twenty-eight porcine anterior chambers were perfused with medium supplemented with 1.67 × 10⁷ pigment particles/mL for 48 hours before treatment with RKI-1447 (n = 16) or vehicle control (n = 12). Intraocular pressure (IOP) was recorded and outflow facility was calculated. Primary trabecular meshwork cells were exposed to RKI-1447 or vehicle control; effects on the cytoskeleton, motility, and phagocytosis were evaluated. Result: Compared to baseline, the perfusion of pigment caused a significant increase in IOP in the RKI-1447 group (P = 0.003) at 48 hours. Subsequent treatment with RKI-1447 significantly reduced IOP from 20.14 ± 2.59 mmHg to 13.38 ± 0.91 mmHg (P = 0.02). Pigment perfusion reduced the outflow facility from 0.27 ± 0.03 at baseline to 0.18 ± 0.02 at 48 hours (P < 0.001). This was partially reversed with RKI-1447. RKI-1447 caused no apparent histological changes in the micro- or macroscopic TM appearance. RKI-1447-treated primary TM cells showed significant disruption of the actin cytoskeleton both in the presence and absence of pigment (P < 0.001) but no effect on TM migration was observed. Pigment-treated TM cells exhibited a reduction in TM phagocytosis, which RKI-1447 reversed. Conclusion: RKI-1447 significantly reduces IOP by disrupting TM stress fibers and increasing TM phagocytosis. These features may make it useful for the treatment of secondary glaucomas with an increased phagocytic load.

After screening nearly 1000 synthetic peptides, a synthetic peptide termed JAL-AK22 (KYEGHWYPEKPYKGSGFRCIHI) derived from the BoxA domain in Tob1 protein was found to activate both unfolded and folded proMMP-7. In addition, JAL-AK22 showed auto-proteolytic activity. Interestingly, the smaller derivative of JAL-AK22 termed JAL-TA9 (YKGSGFRMI) also possessed auto-proteolytic activity and cleaved 2 fragment peptides (MMP18-33 and MMP18-40) derived from the prodomain of proMMP-7 under physiological conditions. These proteolytic activities were inhibited by AEBSF, a serine protease inhibitor. Our results demonstrate that a small synthetic peptide consisting of only 9 amino acids has serine protease-like activity and activates proMMP-7 by cleaving the prodomain region. We thus propose calling small peptides possessing with protease-like activity Catalytides (catalytic peptides). We expect that our findings will stimulate the development of novel Catalytides and related applications.

Tidal notches, long regarded as reliable indicators of mean sea level, have been extensively studied along carbonate coasts in the central Mediterranean Sea. Previous studies revealed a correlation between the genesis of tidal notches and tidal range, lithology, cliff foot depth and wave energy. In the 2020 Geoswim campaign at Lampedusa, the southernmost island of the Pelagie archipelago (Italy), 'anomalous' tidal notches were identified. Unlike normal notches observed elsewhere, those in Lampedusa's southern bays exhibited a particular behavior —constantly deepening in the inner part of the bays, reaching a maximum depth of approximately 30 cm below sea level and narrowing inwards. Similar phenomena were previously observed by [1] near Marseille (France) and in Gozo Island (Malta). Time-lapse images, alongside measurements of morphometric param-eters, were collected during the survey. Despite the rapid morphological changes of the notches within the bay, the tectonic stability of the studied areas was confirmed by literature and data. Our hypothesis indicates that a combination of marine factors, influenced by local meteomarine conditions driven by the local morphology of the small bays exposed to southern quadrants con-tribute to the formation of these unique landforms. The latter manifest higher lowering erosion rates slightly below mean sea level in sheltered areas, challenging conventional notions about tidal notch formation.

Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

Blasting pattern optimization is an attempt to optimize blast design parameters aiming to achieve optimum fragmentation, reduce mining operating costs as well as environmental side consequences. The present study aims to propose a multi-objective optimization model, employing artificial intelligence and metaheuristics, to simultaneously minimize the mine-to-crusher operating costs and the impact of blasting consequences including fly-rock and back-break. To achieve the purpose of the study, a multi-variable regression model was developed to model total costs from drilling to crushing. In addition to the costs, multilayer perception neural networks were implemented to predict the blast-induced back-break and fly-rock as a function of collected variables such as number of holes, hole length, burden, spacing, hole slope, stemming, blasted rock per hole, powder factor, and charge per delay. High-precise estimations for both back-break and fly-rock were achieved with the average of 99% coefficient of determination for train, test and validation data sets. Then, the developed regression model and the neural networks were used in an optimization framework, employing Grasshopper algorithm, to find the optimum blast design satisfying practical constraints. The proposed model was tested on a lead-zinc open-pit mine, where 1032 blasting patterns were recorded and analyzed. The results of the optimization model provide a Pareto set of solutions, such that any of these solutions can be implemented according to the strategy of the mining operation management team. The blast pattern with the lowest cost, result in a relatively high fly-rock and back-break, while the pattern with low fly-rock and back-break raises the cost by 20.13 % compared the minimum cost blast design.

The study of fractures in the subsurface is very important in unconventional reservoirs since they are the main conduits for hydrocarbon flow. For this reason, a variety of equivalent medium theories have been proposed for the estimation of fracture and fluid properties within reservoir rocks. We experimentally investigated the feasibility of applying the Galvin model in fractured tight stones. For this proposal, three artificial fractured tight sandstone samples with the same background porosity (11.7% ± 1.2%) but different fracture densities of 0.00, 0.0312, and 0.0624 were manufactured. The fracture thickness was 0.06 mm and the fracture diameter was 3 mm in all the fractured samples. Ultrasonic P- and S-wave velocities were measured at 0.5 MHz in a laboratory setting in dry and water-saturated conditions in directions at 0°, 45°, and 90° to the fracture normal. The results were compared with theoretical predictions of the Galvin model. The comparison showed that model predictions significantly underestimated P- and S- wave velocities as well as P-wave anisotropy in water-saturated conditions, but overestimated P-wave anisotropy in dry conditions. By analyzing the differences between the measured results and theoretical predictions, we modified the Galvin model by adding the squirt flow mechanism to it and used the Thomsen model to obtain the elastic moduli in high- and low-frequency limits. The modified model predictions showed good fits with the measured results.

Maize (Zea mays) is one of the most important staple food and primary source of livestock feed in the world. As the consumption of maize grown on the selenium-enriched soils of Naore Valley is one of the apparent causes of selenosis in the area, this work collected and analyzed total Se, Se fractions, and Se species distributions in maize plant samples, including grains, leaves, stalks, roots, rhizosphere soils, and the most representative parent rock materials from Naore Valley, Ziyang County, China. The Se distribution in soils markedly correlated with the weathered Se-enriched bedrocks, but most of the Se in the analyzed soils is enclosed as recalcitrant residual Se and organic-sulfide bound Se. In contrast, Se in rocks had a comparatively higher bioavailability and is bounded mainly to organic matter and sulfides minerals, with very few of the Se enclosed in the residual fraction. Maize plants might take a large amount of Se from the organic-sulfide bound Se fraction in the Se-rich soils, the weathered products from bedrocks or plant litters. Total Se concentrations in the collected samples were observed in descending order soil>leaf>root>grain>stalk. The predominant Se species detected in maize plants was SeMet. Se inorganic forms, mainly Se(VI), decreased from root to grain and were possibly assimilated into organic forms. Se (IV) was barely present. The natural increases in Se concentration affected mainly leaf and root dry-weight biomass as they are the organs that coped with the highest Se accumulation. This paper offers an insight into the uptake, accumulation, and distribution of Se forms in natural Se-rich maize crops and an opportunity for shifting Se-rich soils from menaces to valuable resources for growing Se-rich agricultural products.

Most of the pore-scale imaging and simulations of non-Newtonian fluid are based on the simplifying geometry of network modeling and overlook the fluid rheology and heat transfer. In the present paper, we developed a non-isothermal and non-Newtonian numerical model of the flow properties at pore-scale by direct simulation of the 3D micro-CT images using a Finite Volume Method (FVM). The numerical model is based on the resolution of the momentum and energy conservation equations. Owing to an adaptive meshing technique and appropriate boundary conditions, rock permeability and mobility are accurately computed. A temperature and concentration-dependent power-law viscosity model in line with the experimental measurement of the fluid rheology is adopted. The model is first applied at isothermal condition to 2 benchmark samples, namely Fontainebleau sandstone and Grosmont carbonate, and is found to be in good agreement with the Lattice Boltzmann method (LBM). Finally, at non-isothermal conditions, an effective mobility is introduced that enables to perform a numerical sensitivity study to fluid rheology, heat transfer, and operating conditions. While the mobility seems to evolve linearly with polymer concentration, the effect of the temperature seems negligible by comparison. However, a sharp contrast is found between carbonate and sandstone under the effect of a constant temperature gradient. Besides concerning the flow index and consistency factor, a good master curve is derived when normalizing the mobility for both the carbonate and the sandstone.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The present study aimed to develop a feeding strategy for pregnant sows which involved the prenatal administration of a mixture of pancreatic-like fungal enzymes, such as lipase, amylase, and protease, at (1) 1–115 days of gestation (group D1) and (2) 80–115 days of gestation (group D2) and to carry out a comparison with groups of sows that were not receiving such supplementation (negative control [NC] and positive control [PC]). It was found that the administration of the enzyme supplement resulted in a significant shortening of gestation (P ≤ 0.01). The pancreatic enzymes administered to sows had a significant effect on the number of liveborn piglets and weaned piglets, which was higher compared to the control groups that did not receive supplementation respectively: D1-12.1±1.1 and 11.12±1.1; D2- 12.8±1.3 and 11.75±0.07 vs. control groups KN-10.7±1.0 and 9.62±0,95 and KP 10.9±1.2 and 10.15±1.0 (P<0.006). Significant changes in piglet growth were observed after weaning up to 70 days of age. During this period, the most favorable growth parameters were found in groups D2 (420±91g) and PC (407±103g), in which piglets were given a mixture of pancreatic enzymes (lipase, amylase, and protease) at 3 weeks of age, and significantly higher weight gain and feed intake were observed compared to groups NC (378±114g) and D1 (381±96g) (P ≤ 0.007). In contrast, insulin levels were significantly lower in groups D1 and D2, respectively 6,8 IU/ml and 6,7 IU/ml compared to groups NC (14,6 IU/ml) and PC (16,6 IU/ml) ( (P ≤ 0.01). Piglets in group D2 had a significantly better feed conversion ratio (FCR) 1.604±0.10 compared to the other dietary groups: KN– 1.986±0.14; KP– 1.704±0.11; D1 – 1.932±0.15 (P ≤ 0.03). Histological imaging confirmed significantly thicker intestinal epithelium and intestinal mesenteron in animals from groups D2 and PC (P ≤ 0.03). Animals from the groups KP, D1 and D2 receiving enzymes showed a highly significant increase in the surface area of pancreatic follicles and pancreatic surface area compared to the group without KN supplementation (P<0.01). Furthermore, significantly higher activity of the brush border enzyme lactase was observed in groups D1; D2 and PC compared, respectively 32.90±3.99; 30.00±6.83 and 29.60±29.60 to group NC – 21.80± 3.27 (P ≤ 0.01).

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

Globally, rotavirus group A (RVA) remains a major cause of severe childhood diarrhea, despite the use of vaccines in &gt; 100 countries. RVA sequencing for local outbreaks facilitates investigation into strain composition, origins, spread, and vaccine failure. In 2018, we collected 248 stool samples from children aged &lt;13 years admitted with diarrheal illness to Kilifi County Hospital, coastal Kenya. Antigen screening detected RVA in 55 samples (22.2%). Of these, VP7 (G) and VP4 (P) segments were successfully sequenced in 48 (87.3%) and phylogenetic analysis based on the VP7 sequences identified seven genetic clusters with six different GP combinations; G3P[8], G1P[8], G2P[4], G2P[8], G9P[8] and G12P[8]. The G3P[8] strains predominated the season (n=37, 67.2%) and comprised three G3 genetic clusters that fell within Lineage I and IX (the latter also known as equine-like G3 lineage). Both two G3 lineages have been recently detected in several countries. Our study is the first to document African children infection with G3 lineage IX. These data highlight the global nature of RVA transmission and the importance of increasing global rotavirus vaccine coverage.

Globin-like superfamily constitutes a superfamily of both extracellular and intracellular proteins that are found in 3 kingdoms of life. Globins are respiratory proteins that usually bind an oxygen molecule .Earlier, phylogenetic study of globin like superfamily was based on morphological character, however, molecular basis of their functional diversity is not completely understood. The present study focuses on the phylogenetic analysis of globin at molecular level. Firstly, proteins of SCOP families of globin like superfamily were retrieved from NCBI and then similar proteins are retrieved from PSI BLAST results and then pfam was used to predict the domains and two domains: Globin and Phycobilisome were analysed. Other analysis predicted the localization in cytoplasm of most of the proteins. The nucleotide sequences of same species for protein analysis were retrieved from NCBI, and phylogenetic analysis of aligned fasta files of proteins and nucleotides by using MEGA at molecular level was performed and analysis shows the difference on taxonomic tree and phylogenetic tree.

This study aimed to overcome the difficulty of conducting the horizontal-well cavity leaching test in the field and to investigate the long-term stability of the horizontal-well salt-cavity natural gas storage. The simulation test design is combined with the similarity theory to study the cavity expansion characteristics and the influence law of cavity leaching parameters. Through the design of a rubber hose connection, an integrated closed test system for multi-stage horizontal-well cavity leaching and brine drainage was built. The test system also realises the repeatable backward movement of the injection well during the test. A similarity simulation of the test design was carried out, and the test platform was constructed to carry out multi-stage horizontal-well leaching tests with a nitrogen cushion. In the horizontal-well leaching tests with a nitrogen cushion, the influence laws of the well spacing, flow rate and liquid level position on cavity expansion were investigated. Based on the morphological characteristics of the horizontal-well cavity, a numerical model of the horizontal-well salt cavity was developed, which reflects the real cavity morphology leached in the test. The long-term stability of the horizontal-well salt-cavity natural gas storage under different internal pressures was investigated through numerical simulation.

The use of mixed-state ionic beams in collision dynamics investigations is examined. Using high resolution Auger projectile spectroscopy involving He-like ($1s^2\thinspace^1\!S, 1s2s\thinspace^{3,1}\!S$) mixed-state beams, the spectrum contributions of the $1s2s\thinspace^3\!S$ metastable beam component is effectively separated and clearly identified. This is performed with a technique that exploits two independent spectrum measurements under the same collision conditions, but with ions having quite different metastable fractions, judiciously selected by varying the ion beam charge-stripping conditions. Details of the technique are presented together with characteristic examples. In collisions of 4 MeV B$^{3+}$ with H$_2$ targets, the Auger electron spectrum of the separated $1s2s\thinspace^{3}S$ boron beam component allows for a detailed analysis of the formation of the $1s2s(^3\!S)nl \thinspace^2\!L$ states by direct $nl$ transfer. In addition, the production of hollow $2s2p\thinspace^{1,3}\!P$ doubly- and $2s2p^2\thinspace^2\!D$ triply-excited states, by direct excitation and transfer-excitation processes, respectively, can also be independently studied. In similar mixed-state beam collisions of 15 MeV C$^{4+}$ with H$_2$, He, Ne and Ar targets, the contributions of the $1s^2$, $1s2s\thinspace^{3,1}S$ beam components to the formation of the $2s2p\thinspace^{3,1}\!P$ states by double-excitation, $1s\rightarrow2p$ excitation and transfer-loss processes can be clearly identified, facilitating comparisons with theoretical calculations.

Despite the recognized potential of nanoparticles, only a few formulations have progressed to clinical trials, and an even smaller number have been approved by the regulatory authorities and marketed. Virus-like particles (VLPs) have emerged as promising alternatives to most explored nanoparticles because of the absence of viral genetic material, their incapacity to replicate, mimicry of viral structure, and tropism conservation. Furthermore, VLPs can be surface functionalized with small molecules to improve circulation half-life and target specificity. Through the functionalization and coating of VLPs, it is possible to optimize the response properties to a given stimulus, such as heat, pH, an alternating magnetic field, or even enzymes. Surface functionalization can also modulate other properties, such as biocompatibility, stability, and specificity, deeming VLPs as potential vaccine candidates or delivery systems. In this review, we address the different types of functionalization of VLPs, their importance, and their consequent biomedical applications.

Glypicans are a family of heparan sulfate proteoglycans that are attached to the outer plasma membrane leaflet of the producing cell by a glycosylphosphatidylinositol anchor. Glypicans are involved in the regulation of many signalling pathways, including those that regulate the activities of Wnts, Hedgehog (Hh), Fibroblast Growth Factors (FGFs) and Bone Morphogenetic Proteins (BMPs), among others. In the Hh signalling pathway, glypicans have been shown to be essential for ligand transport and the formation of Hh gradients over long distances, for the maintenance of Hh levels in the extracellular matrix and for its unimpaired reception in distant recipient cells. Recently, two mechanistic models have been proposed to explain how Hh can form the signalling gradient and how glypicans may contribute to it. In this review, we describe the structure, biochemistry and metabolism of glypicans and their interactions with different components of the Hh signalling pathway that are important for the release, transport and reception of Hh.

Cardiac hypertrophy typically follows myocardial damage, a process known to involve members of the Krüppel-Like Factors (KLFs) which have pro-hypertrophic and anti-hypertrophic roles. Our study delved into the molecular mechanisms underlying KLFs-cardiac hypertrophy interplay post myocardial infraction. We induced myocardial dam-age in rats using isoproterenol. Total RNA was extracted from the left ventricle and Quantitative Real Time RT-PCR was conducted to assess the expression of KLFs, cardiac commitment genes, inflammatory markers, and certain conduction-related genes. We devel-oped a computational approach to construct a proteomic network centered on KLFs. Initial results revealed early expression (2-3 days post-induction) of KLF3, KLF4 and KLF6, followed by the subsequent expression of KLF11 and KLF15 (5-8 days after induction). In the maturation stage, KLF12 and KLF13 regulators were found upregulated. IL-6 was gradually found to be upregulated through. Interaction analysis revealed KLF3, KLF8 and KLF12 interacted with cardiac electrical functions. RT-PCR confirmed up-regulation in cardiac genes linked to electrical function and scar maturation. Our findings underscore the central role of KLFs during the modulation of the cardiac hypertrophic response. Dysregulation of KLF expression resulted in damaged myocardium, participating in the progression of abnormal hypertrophy, highlighting their potential as therapeutic targets for heart diseases.

Background: The number of people with type 2 diabetes is increasing daily, and therefore effective therapy is needed to successfully regulate glycemia and reduce the risk of associated complications. Recently, an oral formulation of the glucagon-like peptide-1 receptor agonist (GLP-1 RA) semaglutide has become available. Therefore, the aim of our study was to compare the effectiveness of the new oral formulation and the existing injectable formulation of semaglutide in terms of glycemic and body weight control in a real-world setting. Patients and methods: This was a single-center retrospective observational study conducted at the Rijeka Clinical Hospital Centre. A total of 106 patients with inadequately controlled type 2 diabetes (HbA1 ≥ 7%) on different oral or basal insulin supported oral therapy were recruited from the diabetes outpatient clinic, and data from electronic medical records were retrospectively collected and analyzed from May 2021 to November 2022. All subjects were GLP-1 RA naive and consequently prescribed 0.5 or 1.0 mg once weekly injectable semaglutide (IS) or 7 mg or 14 mg once daily oral semaglutide (OS) for at least 6 months. Glycated hemoglo-bin (HbA1c), body weight, and body mass index (BMI) were assessed prior to semaglutide administration and after a 6-month follow-up period. The primary endpoint was the change from baseline in HbA1c, and sec-ondary endpoints were the change in body weight and the proportion of participants with a reduction in body weight of ≥ 5% and ≥ 10%, respectively, 6 months after the initiation of semaglutide treatment. Results: At 6-month follow-up, no significant difference was observed between the two formulations in terms of HbA1c reduction (IS -1.1% vs OS -1.4%, p=0.126) and weight loss (IS -6.50 kg vs OS -5.90 kg, p=0.714). Exactly the same proportion of participants in both groups achieved a weight loss of ≥ 5% (56.7%, n=30). A weight loss ≥ 10% was observed in 20.7% (n=11) of participants administered IS and 15.1% (n=8) of participants adminis-tered OS, respectively (p=0.454). Conclusion: In a real-world setting, oral semaglutide as add-on therapy to ongoing antihyperglycemic treatment in patients with inadequately controlled type 2 diabetes who had not previously received GLP-1 RA demonstrated the same effectiveness as injectable semaglutide in terms of gly-cemic control and weight loss after 6 months of treatment.

Emerging evidence indicates that intracellular calcium (Ca2+) levels and their regulatory proteins play essential roles in normal stem cell proliferation and differentiation. Cancer stem-like cells (CSCs) are subpopulations of cancer cells that retain characteristics similar to stem cells and play an essential role in cancer progression. Recent studies have reported that the Orai3 calcium channel plays an oncogenic role in human cancer. However, its role in CSC remains underexplored. In this study, we explored the effects of Orai3 in the progression and stemness of oral/oropharyngeal squamous cell carcinoma (OSCC). Orai3 expression was increased in a stepwise manner during the progression of OSCC. In addition, Orai3 was highly enriched in CSC populations of OSCC. Ectopic Orai3 expression in non-tumorigenic immortalized oral epithelial cells increased intracellular Ca2+ levels, acquiring malignant growth and CSC properties. Conversely, silencing of endogenous Orai3 in OSCC cells suppressed CSC phenotype, indicating a pivotal role of Orai3 in CSC regulation. Moreover, Orai3 markedly increased the expression of inhibitor of DNA binding 1 (ID1), a stemness transcription factor. Orai3 and ID1 were highly expressed in CSCs compared to non-CSCs, implying the functional importance of the Orai3/ID1 axis in CSC regulation. Furthermore, suppression of ID1 abrogated CSC phenotype in the cell with ectopic Orai3 overexpression and OSCC. Our study reveals that Orai3 is a novel functional CSC regulator in OSCC and further suggests that Orai3 plays an oncogenic role in OSCC by promoting cancer stemness via ID1 upregulation.

Venoms are a rich source of bioactive compounds, and among them is leberagin-C (Leb-C), a disintegrin-like protein derived from the venom Macrovipera lebetina transmediterrannea snakes. Leb-C has shown promising inhibitory effects on platelet aggregation. Previous studies have demonstrated that this SECD protein specifically targets α5β1, αvβ3 and αvβ6 integrins through a mimic mechanism of RGD disintegrins. In our current study, we focused on exploring the potential effects of Leb-C on metastatic breast cancer. Our findings revealed that Leb-C disrupted the adhesion, migration, and invasion capabilities of MDA-MB-231 breast cancer cells and its highly metastatic D3H2LN sub-population. Additionally, we observed significant suppression of adhesion, migration, and invasion of Human Umbilical Vein Endothelial Cells (HUVECs). Furthermore, Leb-C demonstrated a strong inhibitory effect on fibroblast growth factor 2-induced proliferation of HUVEC. We conducted in vivo experiments using nude mice and found that treatment with 2 µM of Leb-C resulted in a remarkable 73% reduction in D3H2LN xenograft tumor size. Additionally, quantification of intratumor microvessels revealed a 50 % reduction in tumor angiogenesis in xenograft after 21 days of twice-weekly treatment with 2 µM of Leb-C. Collectively, these findings suggest the potential utility of this dinsintegrin-like protein for inhibiting aggressive and resistant metastatic breast cancer.

KLFs seem to associate with congenital heart disease-linked syndromes, malformations because of autosomal diseases, mutations that relate to protein instability, and/or loss functions such as atheroprotective activities. Ischemic damage also relates to KLF dysregulation because of differentiation of cardiac myofibroblasts or a modified fatty acid oxidation, related to the formation of a dilated cardiomyopathy; myocardial infarctions, left ventricular hypertrophy and diabetic cardiomyopathies. MicroRNA have been involved in certain regulatory loops of KLFs as they may function as critical modulators of vascular smooth muscle cells in atherosclerosis, in heart failure and as markers of endothelial damage in acute myocardial infarction.

Glioblastoma (GBM) still presents as one of the most aggressive tumors in the brain, which despite enormous research efforts remains incurable until today. As many theories evolve around the persistent recurrence of this malignancy the assumption of a small population of cells with a stem-like phenotype remains as a key driver of its infiltrative nature. In this article we research Chordin-like 1 (CHRDL1), a secreted protein, as a potential key regulator of the glioma stem-like cell (GSC) phenotype. It has been shown that CHRDL1 antagonizes the function of Bone Morphogenic Protein 4 (BMP4), which induces GSC differentiation and hence reduces tumorigenicity. We therefore employed two previously described GSCs spheroid cultures and depleted them of CHRDL1 using stable transduction of a CHRDL1-targeting shRNA. We show with in vitro cell based assays (MTT, limiting dilution and sphere formation assays), western blots, irradiation procedures and quantitative real-time PCR that depletion of the secreted BMP4 antagonist CHRDL1 prominently decreases functional and molecular stemness traits resulting in enhanced radiation sensitivity. As a result, we postulate CHRDL1 as an enforcer of stemness in GSCs and find additional evidence that high CHRDL1-expression might also serve as a marker protein to determine BMP4-susceptibility.

Purpose: The study aimed to investigate if there were any links between liver function biomarkers and immunoglobulins levels in serum, and Toll-like receptors (TLRs) and neuropilin-1 (NRP1) in COVID-19 patients. The study also aimed to assess the accuracy—sensitivity, specificity, and area under the curve (AUC) by the receiver operator curve (ROC) analysis for immunoglobulins levels and TLRs expressions. Patients and Methods: This study included 150 patients (100 patients with confirmed COVID-19 and 50 healthy volunteers as a control group). Patients with COVID-19 were subdivided into two groups according to the severity of symptoms (moderate and severe, with 50 patients each). Serum C-reactive protein (CRP), alanine aminotransaminase (ALT), aspartate aminotransaminase (AST), albumin, lactate dehydrogenase (LDH), immunoglobulin (Ig) G, and IgM levels were estimated. TLRs (TLR2 and TLR4) and NRP1 gene expression in blood samples were investigated using quantitative real-time polymerase chain reaction (qRT-PCR). ROC analysis was also applied to determine the accuracy of various detected parameters in predicting the possibility of COVID-19 infection. Results: In COVID-19 patients, serum parameters related to liver function, except serum albumin, CRP, IgG, IgM, and TLR2, TLR4, and NRP1 mRNA expression levels, significantly elevated compared to controls. Severe COVID-19 patients exhibited significantly higher liver enzymes (ALT, AST and LDH), CRP, and TLR2 mRNA expression levels and lower albumin levels than the moderate group. In the moderate and severe groups, ALT, CRP, TLR2, and TLR4 had a significant positive correlation with IgM levels. ALT, AST, LDH, CRP, TLR2, and TLR4 showed a significant positive correlation with IgG levels in both groups. In both the moderate and severe groups, NRP1 expression was found to be significantly correlated with CRP, IgG, IgM, TLR2, and TLR4. In contrast, serum albumin levels exhibited a significant negative correlation with IgG and IgM levels only in the severe group, but they showed a significant negative correlation with TLR2, TLR4, and NRP1 expression in both moderate and severe groups. Serum ALT and AST activities were positively correlated with NRP1 expression in the moderate group but not in the severe group and as well as TLR2 and TLR4 expression in both the moderate and severe groups. ROC analysis indicated that AUC was higher than 0.800 for serum IgM level and TLR4 gene expression in moderate COVID-19 group. Conclusions: The increased liver function biomarkers in serum and NRP1 expression are closely correlated with sustained activations in humoral and innate immune responses during COVID-19 infection. As a result, TLR2, TLR4, and NRP1 could be targets for limiting COVID-19 infection and impairment effects on liver function. Moreover, detection of IgM level in serum and TLR4 expression in blood have a good accuracy in predicting the possibility of infection with COVID-19 in moderate cases.

Background/Aim: Uterine leiomyoma, also known as fibroids, is the most common benign neoplasm of the female genital tract. Leiomyoma, including its subtypes, is the most common uterine tumor. The subtypes account for approximately 10% of leiomyomas. Intravenous leiomyomatosis, a uterine leiomyoma subtype, is an intravascular growth of benign smooth muscle cells, occasionally with pelvic or extrapelvic extension. Uterine leiomyosarcoma, a malignant tumor, tends to metastasize hematogenously, and distant metastasis to the lungs and liver is common. Therefore, this intravenous leiomyomatosis’ oncological features resemble those of the malignant tumor uterine leiomyosarcoma. Cancer stem cells migrate to distant organs via intravascular infiltration, leading to micrometastases. Materials and Methods: We examined the oncological properties of intravenous leiomyomatosis using molecular pathological techniques on tissue excised from patients with uterine leiomyoma. Result: CD44-positive mesenchymal tumor stem-like cells were detected in both intravenous leiomyomatosis and uterine leiomyosarcoma. The oncological nature of intravenous leiomyomatosis was found to be similar to the oncological properties of uterine leiomyosarcoma. However, in intravenous leiomyomatosis, Cyclin E and Ki-67-positive cells were rare, and no pathological findings suspected to be malignant were observed. Conclusion: It is expected that establishing a treatment method targeting cancer stem cells will lead to the treatment of malignant tumors with a low risk of recurrence and metastasis.

: Glioblastoma (GBM) is the most common and most aggressive primary brain tumor with a very high rate of recurrence and a median survival of 15 months after diagnosis. Abundant evi-dence suggests that a certain sub-population of cancer cells harbors a stem-like phenotype and is likely responsible for disease recurrence, treatment resistance and potentially even for the infil-trative growth of GBM. GBM incidence has been negatively correlated with the serum levels of 25-hydroxy-vitamin D3, while the low pH within tumors has been shown to promote the ex-pression of the vitamin D3-degrading enzyme 24-hydroxylase, encoded by the CYP24A1 gene. Therefore, we hypothesized that calcitriol can specifically target stem-like glioblastoma cells and induce their differentiation. Here, we show using in vitro limiting dilution assays, quantita-tive real-time PCR and ex vivo adult organotypic brain slice transplantation cultures that thera-peutic doses of calcitriol, the hormonally active form of vitamin D3, reduces stemness to varying extent in a panel of investigated GSC lines and effectively hinders tumor growth of responding GSCs ex vivo. We further show that calcitriol synergizes with Temozolomide ex vivo to com-pletely eliminate some GSC tumors. These findings indicate that calcitriol carries potential as an adjuvant therapy for a subgroup of GBM patients and should be analyzed in more detail in fol-low-up studies.

Toll-like receptors (TLRs) are a class of pattern recognition receptors (PRRs) family that identify pathogen-associated molecular patterns derived from microbes and activate immune cell response. Following TLRs ligation, different adaptor and transcription molecules such as myeloid differentiation primary response gene 88 (MyD88) and nuclear factor kappa B (NF-kB) are recruited that initiate inflammatory signaling pathways. The human Toll-like receptor 10 (hTLR10) is a novel member of the PRRs family with a regulatory function of immune responses because of unique cytoplasmic domains which lead to induction of both inflammatory and anti-inflammatory properties. Recent studies have reported the association of TLR10 polymorphisms with many inflammatory diseases and human cancer. Engagement of TLR10 on the surface of the epithelium and macrophages leads to the production of proinflammatory cytokines and chemokines, while other studies have proven an anti-inflammatory role of TLR10. Accordingly, TLR10 suppresses proinflammatory cytokine production via negative regulation of MyD88 and the Akt (protein kinase B) and MAPK (mitogen-activated protein kinase) signaling pathways. This review aimed to provide answers for these conflicting findings (Inflammatory and anti-inflammatory properties of TLR10) to further identify distinct biological functions of TLR10.

Bufadienolides-like chemicals, which mostly composed the active ingredient of Chansu, had been widely discovered to possess anti-inflammatory, tumor-suppressing and antipain activity, but the mechanisms of action were not clearly illuminated. In this research, in order to explore the potential mechanism of bufadienolides-like chemicals on breast cancer, a serious of bioinformatics analysis, included (1) differentially expressed genes identification combined with gene set variation analysis, (2) tissue specific co-expression network construction, (3) differentially regulated sub-networks detection with disease phenome, (4) hub gene selection and it’s relation to survival probability, and (5) similar small molecule detection were performed with gene expression profiles of bufadienolides-like chemicals. Results indicated bufadienolides-like chemicals had the most same target with valproic, estradiol and etc, could disturbed the pathways in RNA splicing, apoptotic process, cell migration, extracellular matrix organization, adherens junction organization, synaptic transmission, Wnt signaling, AK-STAT signaling, BMP signaling pathway and unfolded protein response, and had the potential ability to be used as anticancer, hormones and vasoprotectives agents.

Toll-like receptor 4 (TLR4) is a member of the TLR family. Members of the TLR family play an important role in innate immune responses and are induced by recognition of pathogen-associated molecular patterns. They are also involved in cell proliferation and apoptosis in cancer. We investigated the role of TLR4 in apoptotic cell death in gynecological cancer cells; gynecological cancer is associated with infertility and spontaneous abortion. To examine the effect of TLR4 activation on apoptotic signaling in cancer cells, cultured primary cancer cells were treated with the TLR4 agonist lipopolysaccharide (LPS). The morphology of cancer cells was compared with normal myometrial cells. Enhanced growth rate and loss of contact inhibition with cellular overlap was observed in the cancer cells. The molecular mechanism analysis revealed differential expression of tumor suppressor genes in LPS-treated cancer cells. The expression of apoptosis-related caspase-3 was increased significantly in cancer cells with TLR4 activation after exposure to LPS. Taken together, these results suggest the pro-apoptotic activity of TLR4 as a potential therapeutic target for the treatment of gynecological cancers.

Astronauts at are risk of losing 1.0 – 1.5% of their bone mass for every month they spend in space despite their adherence to high impact exercise training programs designed to preserve the musculoskeletal system. This article reviews the basics of bone formation and resorption and details how exposure to microgravity or simulated microgravity affects the structure and function of osteoblasts, osteocytes, osteoclasts, and their mesenchymal and hematologic stem cell precursors. It details the critical roles that insulin-like growth facor-1 and its receptor IGFR1 play in maintaining bone homeostasis and how exposure of bone cells to microgravity affects the function of these growth factors. Lastly, it discusses the potential of tumor necrosis factor-related apoptosis-inducing ligand, syncytin-A, and sclerostin inhibitors and recombinant IGF-1 as a bone-saving treatment for astronauts in space and during their colonization of the Moon.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

The paper proposes a rock classification method using the vibration signal of the rotary drilling process. This proposed method classifies four rocks with a reliability of 100 %, from the vibration signal record of a lasting 1/4 second. For the design of a suitable classification method, several attributes of the vibration signal were calculated for two different signal recording lengths. Cluster dendrogram, ANOVA test, and boxplot were used to determine useful attributes and proper signal length. The classification rule was found using a decision tree, machine learning tool. The publication gradually describes the process of creating the classification method and the results of the reliability verification of the proposed classification method. Rock disintegration by rotary drilling was carried out under standardized experimental conditions. The disintegration rocks were andesite, granite, limestone, and concrete.

Mine waste rock and drainage pose lasting environmental, social, and economic threats to the mining industry, regulatory agencies, and society as a whole. Mine drainage can be alkaline, neutral, moderately or extremely acidic and contains significant levels of sulfate, dissolved iron, and frequently a variety of heavy metals and metalloids, such as cadmium, lead, arsenic, and selenium. In acid neutralization by carbonate and silicate minerals, a range of secondary minerals can form and possibly scavenge these potentially harmful elements. Apart from the extensively-studied microbial-facilitated sulfide oxidation, the diverse microbial communities present in mine rock and drainage may also participate in the formation, dissolution, and transformation of secondary minerals influencing the mobilization of these metals and metalloids. This article reviews major microbial-mediated geochemical processes occurring in mine rock piles that affect drainage chemistry, with a focus on the role of microorganisms in the formation, dissolution and transformation of secondary minerals. Understanding this is crucial for developing biologically-based measures to deal with contaminant release at the source, i.e., source control.

The construction of random fillings from the excavation of medium hardness rocks, with high particle sizes, presents limitations in compaction control. This research applies new control techniques with revised test procedures in the construction of the random fillings core, which constitutes the main part of the embankment, with the bigger volume and provides the geotechnical stability to the infrastructure. The maximum layer thickness researched was 800mm. As there are many types of rocks, this research is applied to metamorphic slates. Quality control has been carried out by applying new research associated with the revision of wheel impression test, topographic settlements and plate bearing test (PBT). A statistical analysis of the core of 16 slate random fillings has been carried out, with a total of 2250 in situ determination of density and moisture content, 75 wheel impression tests, 75 topographic settlement control and 75 PBT. The strong associations found between different tests have allowed to simplify the quality control.

With global warming and accelerated degradation of permafrost, the engineering problems caused by the formation of weak zones between the shallow and permafrost layers of soil–rock mixture (S-RM) slopes in permafrost regions have become increasingly prominent. To explore the influence of rock content on the shear strength of the S-RM freezing–thawing interface, the variation in the shear strength for different rock content is studied herein using direct shear tests. In addition, a 3D laser scanner is used for obtaining the topography of the shear failure surface. Combined with the analysis results of the shear band-particle calculation model, the influence of the rock content on the shear strength of the interface is explored. It was found that the impact threshold of the rock content on the interface strength and failure mode is approximately 30%, when the rock content (R) is &gt; 30% and that the shear strength increases rapidly with increasing rock content. When R ≤ 30%, the actual shear plane is similar to waves; when R &gt; 30%, the shear plane appears as gnawing failure. The shear strength of S-RM freezing–thawing interface mainly comes from the bite force and friction between particles. The main reason for the increase in shear strength with increasing rock content is the increase in bite force between particles, which makes the ratio of bite force to friction force approximately 1:1.

The use of natural stone has a historical and environmental value that makes it strategically valuable for landscape conservation in Europe. Marble, among others, is widely spread on Earth, and it offers high-performance features in architectural applications. However, the complexity of these formations and the rock variability in different ore bodies require detailed studies of the natural and induced stress state, the fracturing degree, and the influence of external factor (such as temperature and/or chemical agents) on the mechanical properties in order to optimize the exploitation processes by reducing extractive waste. This article shows a series of studies conducted by the authors over the last 20 years aimed at making the exploitation of marble blocks in the Carrara basin safer, more efficient, and, therefore, more sustainable. In particular, studies for increasing the knowledge on the natural and the induced stress state through on-site measurements and numerical modeling, studies to improve the quality of the exploited material through improvements of cutting technologies, studies to improve the knowledge of the mechanical behavior of the material under varying loads and temperature conditions and studies to improve the reuse of water materials and their reduction are reported.

Strata and surface movement induced by mining under open-pit final slope is a huge threat to mine safety. Physical model test is an important method to study mining-induced strata and surface movement laws. Because of rock joints predominantly control rock mass deformation and failure, thus physical model test leaving out of consideration of rock joints is difficult to reflect the influence of rock joints on rock mass deformation. Therefore, this paper presents a three-dimensional physical model test considering simplified dominant rock joints. This test process includes the design of testing equipment, the construction of physical model with dominant rock joint sets, conduction of mining and deformation monitoring. And mining under eastern final slope of Yanqianshan iron mine was selected as a case to study the behavior of mining-induced strata and surface movement.

Jingmen viruses are newly described segmented flavi-like viruses that have a worldwide distribution in ticks and have been associated with febrile illnesses in humans. Computational analyses were used to predict that Jingmen flavi-like virus glycoproteins have structural features of class II viral fusion proteins, including an ectodomain consisting of beta-sheets and short alpha-helices, a fusion peptide with interfacial hydrophobicity and a three domain architecture. Jingmen flavi-like virus glycoproteins have a sequence enriched in serine, threonine and proline at the amino terminus, which is a feature of mucin-like domains. Several of the serines and threonines are predicted be modified by the addition of O-linked glycans. Some of the glycoproteins are predicted to have an additional mucin-like domain located prior to the transmembrane anchor, whereas others are predicted to have a stem consisting of two alpha-helices. The flavivirus envelope protein and Jingmen flavi-virus glycoproteins may have diverged from a common class II precursor glycoprotein with a mucin-like domain or domains acquired after divergence.

Glucagon-like peptide-1 (GLP-1) is an incretin hormone that acts on the pancreas to increase insulin and decrease glucagon secretion. Albuminuria is the pivotal marker for diabetic nephropathy, which is the leading microvascular complication of diabetes mellitus. Most of the previous studies mainly focused on the clinical trials of the therapeutic renal protective effect after administration of GLP-1 receptor agonists (GLP-1 RAs), not prior to administration. Therefore, this study aimed to investigate the association between fasting plasma GLP-1 levels and albuminuria before GLP-1 RA administration. A cross-sectional study was designed to evaluate the association between fasting plasma GLP-1 levels and albuminuria in patients with type 2 diabetes mellitus (T2DM). A total of 68 T2DM participants were analyzed from the data at Wonkwang University Hospital in Iksan, Korea. Logistic regression analysis was performed to evaluate the odds ratio (OR) and 95% confidence interval (CI) of the incidence of albuminuria between the GLP-1 low group (Group L) and the high group (Group H). The OR (95% CI) for the incidence of albuminuria comparing the Group L with the Group H of fasting plasma GLP-1 levels was 3.410 (1.160-10.023), p = 0.026 after adjustment for age, gender, fasting plasma glucose, HbA1c, C-peptide, the use of ACE inhibitors or ARBs, SGLT-2 inhibitors, and DPP-4 inhibitors. As a continuous variable, the OR (95% CI) for the incidence of albuminuria associated with the reduction of each 1 pmol/L in fasting plasma GLP-1 levels was 1.673 (1.173-1.870), p = 0.018, after full adjustment. This study showed the negative association between fasting plasma GLP-1 levels and the incidence of albuminuria in Korean patients with T2DM, before GLP-1 RA administration. This result suggests that endogenous GLP-1 may play a role in attenuating albuminuria.

The red fox, found on all continents except Antarctica, occupies diverse habitats. In Croatia it is an indigenous wild species with a population density of 0.7 animals per square kilometer. While tumors in wild animals from the Canidae family are scarce, the true prevalence and diversity of tumors are likely underestimated due to limited research. So far, a limited number of tumors were observed among the red fox population, either in their natural habitat or in captivity. As part of the National rabies control program, we examined 1,890 red fox carcasses over a four-year period. Our focus was on identifying abnormalities on the skin and internal organs that suggest potential neoplastic proliferation. Five red foxes, three males and two females, were found to have growths resembling potential tumors. Their age distribution spanned from 2 to 7 years. Microscopic investigation revealed two collagenous hamartomas, two Meibomian gland adenomas and one intra-abdominal teratoma within a cryptorchid testis. This retrospective study aims to provide a comprehensive description of tumor and tumor-like lesions observed in free-range red foxes from Croatia, marking the first research of its kind in Croatia.

The effect of ferromagnetic CaMnO3 (CMO) addition on structural, magnetic, dielectric, and ferroelec-tric properties of BiFeO3 are presented. X ray diffraction and Raman investigation allowed the identifi-cation of single pseudo cubic perovskite structure. The magnetic measurement showed that the pre-pared films exhibit a ferromagnetic behavior at low temperature with both coercive field and remnant magnetization increased with increasing CMO content. However, a deterioration of magnetization was observed at room temperature. Ferroelectric study revealed an antiferroelectric like behavior with a pinched P-E hysteresis loop for 5%CMO doping BFO resulting in low remnant polarization and double hysteresis loops. Whereas, high remnant polarization and coercive field with a likely square hysteresis loop are obtained for 10 % CMO addition. Furthermore, a bipolar resistive switching behavior with a threshold voltage of about 1.8V is observed for high doped film that can be linked to the ferroelectric polarization switching.

The Burkholderia cepacia complex (Bcc) are a group of increasingly multi-drug resistant opportunistic bacteria that can cause severe pulmonary infections. This resistance is driven through a combination of intrinsic factors and the carriage of a broad range of conjugative plasmids harbouring virulence determinants. Therefore, novel treatments are required to not only treat Bcc infection but also to prevent further spread of these virulence determinants. In the search for phages infective for two clinical Bcc isolates, CSP1 phage, a PRD1-like phage was isolated. CSP1 phage was found to require pilus machinery commonly encoded on conjugative plasmids to facilitate infection of multiple Gram-negative bacteria genera including Escherichia and Pseudomonas. Whole genome sequencing and characterisation of one of the clinical Burkholderia isolates revealed it to be Burkholderia contaminans. B. contaminans 5080 was found to contain a genome of over 8 Mbp encoding multiple intrinsic resistance factors, such as efflux pump systems, but more interestingly, carried three novel plasmids encoding multiple putative virulence factors for increased host fitness, including antimicrobial resistance. Even though PRD1-like phages are broad host range, their use in novel antimicrobial treatments shouldn’t be dismissed, as the dissemination potential of conjugative plasmids is extensive. Continued survey of clinical bacterial strains is

In the chronic phase of chikungunya virus (CHIKV) infection, excessive inflammation manifests as incapacitating joint pain and prolonged arthritis. Arthritis resulted from a large influx of infiltrating immune cells driven by pro-inflammatory cytokines and chemokines originating from the toll-like receptor (TLR)-mediated innate antiviral response. This study investigated fisetin's ability to modulate TLR-mediated antiviral responses against CHIKV in Huh7 cells. The CHIKV inhibitory potential of fisetin was assessed by plaque-forming unit assay, virus yield reduction assay, and bright-field microscopy (cytopathic effect, immunofluorescence). Fisetin’s modulatory potential on TLR-mediated antiviral response was evaluated by immunofluorescence assay (expression of TLR proteins), qRT-PCR (mRNA level of antiviral genes), human cytokine array, and immunoblotting of key transcription factors. The present study showed fisetin induced the expression of the antiviral genes at an early time-point by promoting the phosphorylation of IRF3 and IRF7. Fisetin reduced excessive inflammatory cytokine responses in CHIKV-infected Huh7 cells by impeding the over-phosphorylation of NF-κB. Fisetin also reduced CHIKV-induced cytopathic effects in CHIKV-infected Huh7 cells. Altogether, our study suggests that fisetin modulates TLR-mediated antiviral responses by affecting the CHIKV-induced inflammatory responses.

A half-harmonic oscillator, which gets its name because the coordinate is strictly positive, has been quantized and determined that it was a physically correct quantization. This positive result was found using affine quantization (AQ). The main purpose of this paper is to compare results of this new quantization procedure with those of canonical quantization (CQ). Using Ashtekar-like classical variables and CQ, we quantize the same toy model. While these two quantizations lead to different results, they both would reduce to the same classical Hamiltonian if $\hbar\rightarrow0$. Since these two quantizations have differing results, only one of the quantizations can be physically correct. Two brief sections illustrate how AQ can correctly help quantum gravity and the quantization of most field theory problems.

The measurements of the proton electromagnetic form factors in the time-like region using the initial state radiation technique are reviewed. Recent experimental studies have shown that initial state radiation processes at high luminosity electron-positron colliders can be effectively used to probe the electromagnetic structure of hadrons. The BABAR experiment at the B-factory PEP-II in Stanford and the BESIII experiment at the $\tau$-charm factory BEPC-II in Beijing have measured the time-like form factors of the proton using the initial state radiation process $e^{+}e^{-}\to pbar{p}\gamma$. The two kinematical regions where the photon is emitted from the initial state at small and large polar angles have been investigated. In the first case the photon is in the region not covered by the detector acceptance and is not detected. The Born cross section and the proton effective form factor have been measured over a wide and continuous range of the the momentum transfer squared $q^2$ from threshold up to ~42 (GeV/c)$^2$. The ratio of electric and magnetic form factors of the proton has been also determined. In this report, the theoretical aspect and the experimental studies of the initial state radiation process $e^{+}e^{-}\to p\bar{p}\gamma$ are described. The measurements of the Born cross section and the proton form factors obtained in these analyses near the threshold region and in the relatively large $q^2$ region are examined. The experimental results are compared to the predictions from theory and models. Their impact on our understanding of the nucleon structure is discussed.

There is a relationship between systemic sarcoidosis (SS) and malignancy. Sarcoidosis results from an exaggerated immune response in genetically susceptible individuals. In oncologic pa-tients with sarcoidosis, tumoral antigens and antineoplastic treatment are considered potential triggering factors. The observation of a patient with granulomas in a parotid carcinoma that later developed SS led us to review previous tumors of patients with SS. The aim of the study is to see if granulomas were already present in the tumors that preceded sarcoidosis. We identified 196 sarcoidosis patients, 47 of which had a previous tumor. We were able to review 29 cases 12 of which showed tumor associated granulomas (TAGs)(41.4%). This ratio is much higher than that of the normal population. We analyzed five control patients without sarcoidosis for each tumor. In conclusion, we have observed TAGs in patients who later develop SS. In our series, the ratio of TAGs in patients with SS was significantly greater than in the normal population. To prove our findings, we suggest reviewing the history of patients with SS in search of previous tumors. The histology of such tumors should be reviewed in an attempt to identify granulomas.

Currently, the world is struggling with the coronavirus disease 2019 (COVID-19) pandemic, caused by the severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Prion-like domains are critical for virulence and the development of therapeutic targets; however, the prion-like domains in the SARS-CoV-2 proteome have not been analyzed. In this in silico study, using the PLAAC algorithm, we identified the presence of prion-like domains in the SARS-CoV-2 spike protein. Compared with other viruses, a striking difference was observed in the distribution of prion-like domains in the spike protein, since SARS-CoV-2 was the only coronavirus with a prion-like domain found in the receptor-binding domain of the S1 region of the spike protein. The presence and unique distribution of prion-like domains in the SARS-CoV-2 receptor-binding domains of the spike protein is particularly interesting, since although the SARS-CoV-2 and SARS-CoV S proteins share the same host cell receptor, angiotensin-converting enzyme 2 (ACE2), SARS-CoV-2 demonstrates a 10- to 20-fold higher affinity for ACE2. Finally, we identified prion-like domains in the α1 helix of the ACE2 receptor that interact with the viral receptor-binding domain of SARS-CoV-2. Taken together, the present findings indicate that the identified PrDs in the SARS-CoV-2 receptor-binding domain (RBD) and ACE2 region that interact with RBD have important functional roles in viral adhesion and entry.

The ongoing pandemic of the 2019 novel coronavirus disease (COVID-19) raises a global health crisis, which has resulted in 75,778 confirmed cases with 2130 deaths in China and beyond. Atypical symptom renders it challenging to earlier recognize the 2019-nCoV carrier with the potential ability of equivalent transmission. Therefore, it is needed to gain full spectrum of COVID-19. Here we report clustered COVID-19 cases of person-to-person transmission. The symptoms of typical pneumonia are shared by the two familial members, namely son (Patient 1) and father (Patient 2). Unexpectedly, an influenza-like illness (ILI) is also caused in Patient 3 having close contact with Patient 1 at personal dinner party. Combined with clinical and epidemiological study, chest computed tomography (CT) and molecular diagnosis demonstrate that all the three cases tested positive for COVID-19 with distinct symptoms by human-to-human transmission. To the best of knowledge, it closes in part (if not all), a missing gap of clinical repertoires of COVID-19 outbreaks and underlines the possibility that neglection of cryptic/asymptomatic/mild cold-like syndromes gives biased screen in the earlier stage of COVID-19 cases.

Viruses are the most abundant biological entities in aquatic ecosystems and harbor an enormous genetic diversity. While their great influence on the marine ecosystems is widely acknowledged, current information about their diversity remains scarce. A viral metagenomic analysis of three water samples was conducted from sites on the South Scotia Ridge (SSR) near the Antarctic Peninsula, during the austral summer 2016. The taxonomic composition and diversity of the viral communities were investigated and a functional assessment of the sequences was determined. Phylotypic analysis showed that most viruses belonging to the order Caudovirales, especially the family Podoviridae (41.92-48.7%), similar to the viromes from the Pacific Ocean. Functional analysis revealed a relatively high frequency of phage-associated and metabolism genes. Phylogenetic analyses of phage TerL and Capsid_NCLDV (nucleocytoplasmic large DNA viruses) marker genes indicated that many sequences associated with Caudovirales and NCLDV were novel and distinct from known phage genomes. High Phaeocystis globosa virus virophage (Pgvv) signatures were found in SSR area and complete and partial Pgvv-like were obtained which may have an influence on host-virus interactions. Our study expands the existing knowledge of viral communities and their diversities from the Antarctic region and provides basic data for further exploring polar microbiomes.

Semiconductor materials have been shown to have better photocatalytic behavior and can be utilized for the photodegradation of organic pollutants. In this work, three-dimensional flower-like SnS₂ were synthesized by a facile hydrothermal method. Core-shell structured SiO₂@α-Fe₂O₃ nanocomposites were then deposited on the top of the SnS₂ flowers. The as-synthesized nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM), Brunauer-Emmett-Teller (BET) and photoluminescence spectroscopy (PL). The photocatalytic behavior of the SnS₂-SiO₂@α-Fe₂O₃ nanocomposites was observed by observing the degradation of methylene blue (MB). The results show an effective enhancement of photocatalytic activity for the degradation of MB especially for the 15 wt. % SiO₂@α-Fe₂O₃ nanocomposites on SnS₂ flowers.

Background: Benveniste’s biology experiments suggested the existence of molecular-like effects without molecules (“memory of water”). In this article, it is proposed that these disputed experiments could have been the consequence of a previously unnoticed and non-conventional experimenter effect. Methods: A probabilistic modelling is built in order to describe an elementary laboratory experiment. A biological system is modelled with two possible states (“resting” and “activated”) and exposed to two experimental conditions labelled “control” and “test”, but both biologically inactive. The modelling takes into account not only the biological system, but also the experimenters. In addition, an outsider standpoint is adopted to describe the experimental situation. Results: A classical approach suggests that, after experiment completion, the “control” and “test” labels of biologically-inactive conditions should be both associated with “resting” state (i.e. no significant relationship between labels and system states). However, if the fluctuations of the biological system are also considered, a quantum-like relationship emerges and connects labels and system states (analogous to a biological “effect” without molecules). Conclusions: No hypotheses about water properties or other exotic explanations are needed to describe Benveniste’s experiments, including their unusual features. This modelling could be extended to other experimental situations in biology, medicine and psychology.

The involvement of the prefrontal cortical dopaminergic system in psychopathology of epilepsies and comorbid conditions such as autism spectrum disorder (ASD) still needs to be explored. We used autoradiography to study the D1-like (D1DR) and D2-like (D2DR) receptor binding density in the prefrontal cortex of normal Wistar rats and Wistar-derived strains with generalized convulsive and/or nonconvulsive epilepsies. WAG/Rij rats served as a model for non-convulsive absence epilepsy, WAG/Rij-AGS as a model of mixed convulsive/non-convulsive forms, and KM strain was a model for convulsive epilepsy comorbiding with ASD-like behavioral phenotype. Prefrontal cortex of rats with any of epileptic pathology studied, demonstrated profound decreases in binding densities to both D1DR, D2DR; the effects were localized in the primary and secondary anterior cingulate cortexi, and adjacent regions. The local decreased D1DR and D2DR binding densities were independent (not correlated) from each other. The particular group of epileptic rats with ASD-like phenotype (KM strain), displayed changes in the lateral prefrontal cortex and adjacent regions: D1DR were lowered, but those to D2DR elevated, in anterior dysgranular insular cortex and adjacent regions. Thus, epilepsy-related changes in the dopaminergic system of rat archeocortex were localized in the medial regions, whereas ASD-related candidates were seen in the lateral aspects. The findings point to putative local dopaminergic dysfunctions, associated with generalized epilepsies and/or ASD.

The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

The coastline in the Ca Mau and the Kien Giang provinces of the Vietnamese Mekong Delta has been severely eroded in recent decades. Pile-Rock Breakwaters (PRBW) are one of the most widely adopted structures for controlling shoreline erosion in this region. These structures are effective for wave energy dissipation, stimulating sediment accumulation, and facilitating the restoration of mangrove forests. These breakwaters are generally considered to be best-engineering practice however there is currently insufficient scientific evidence with regard to specific structural design aspects. This can lead to PRBW structures being compromised when deployed in the field. This study uses a physical model of a PRBW in a laboratory to investigate several design parameters, including crest width and working states (i.e. submerged, transition, and emerged), and investigates their relationship with the wave transmission coefficient, wave reflection coefficient, and wave energy dissipation. To investigate these relationships further, empirical formulas were derived for PRBWs under different sea states and crest widths to aid the design process. The results showed that PRBW width had a significant influence on the wave energy coefficients. The findings revealed that the crest width of the breakwater is inversely proportional to the wave transmission coefficient (K_t) under the emerged state. The crest width is also proportional to the wave reduction efficiency and wave energy dissipation in both working states (i.e., submerged and emerged states). The front wave disturbance coefficient (K_f) was found to be proportional to the wave reflection coefficient, and the wave height in front of the structure was found to increase by up to 1.4 times in the emerged state. The wave reflection coefficient requires special consideration to reduce the toe erosion in the structure. Lastly, empirical equations including linear and non-linear formulas were compared with previous studies for different classes of breakwaters. These empirical equations will be useful for understanding the wave transmission efficiency of PRBWs. The findings of this study provide important guidance for PRBW design in the coastal area of the Mekong Delta.

Laboratory experiments were performed to measure the supercritical CO2 (scCO2) storage ratio (%) of the conglomerate and sandstone in Janggi Basin, which are classified as rock in Korea available for CO2 storage. The scCO2 storage capacity was evaluated by direct measurement of the scCO2 amount replacing pore water in a reservoir rock core. The scCO2 sealing capacity of the cap rock (i.e., tuff and mudstone), was also compared by measuring the initial scCO2 seepage pressure (Δp) into the rock core. The measured average scCO2 storage ratio of the conglomerate and the sandstone in Janggi Basin was 30.7 % and 13.1 %, respectively, suggesting that the scCO2 storage capacity is greater than 360,000 metric tons in the Janggi Basin. The initial scCO2 seepage pressure of the tuff in the Janggi Basin was 15 bar and continuous scCO2 injection into the tuff core occurred at Δp higher than 20 bar. For the mudstone, the initial scCO2 seepage pressure was higher than 150 bar (10 times higher than that of the tuff), demonstrating that the mudstone is more suitable than the tuff to shield scCO2 leakage from the reservoir rock in the Janggi Basin.