The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

In the paper, a coordinated control methodology of single-phase (1-P) end-users switching oper-ations on the phases of an active electric distribution network (AEDN) has been proposed to ob-tain a minimum unbalance degree at the coupling common point (CCP) level with the main dis-tribution system. The phase load balancing (PLB) process considers the smart devices that switch from one phase to another phase the 1-P end-users (consumers and prosumers) to compensate for the phase load unbalance. The proposed methodology has been tested successfully in an AEDN belonging to a Romanian Distribution Network Operator (DNO) containing 114 end-users (104 consumers/10 prosumers) integrated into the Smart Metering System (SMS). The op-timal solution leads to a value of the objective function by 1.00004, represented by the unbalance factor, very close to the ideal target, 1.00. A comparative analysis was conducted considering other possible PLB cases (the consumer-level PLB and prosumer-level PLB), obtaining similar values of the UF (1.027 vs. 1.028), slightly higher than in the hybrid-level PLB. Also, the signifi-cant technical benefits were quantified through an energy-saving of 58.73% and decreasing the phase voltage unbalance rate by 91 % compared to the initial case (without PLB). These results emphasized the positive impact of the proposed coordinated control methodology on the PLB process and evidenced its effectiveness and applicability in the AEDNs.

Interferometry is used in magnetic fusion devices to measure the line-1 averaged electron density. It is based on detecting changes in the refractive index of electromagnetic waves traveling through a plasma. The adequate frequency of these electromagnetic waves depends on several limitations. First the maximum expected peak electronic density must be lower than the cutoff density for that frequency. This means that the waves can still propagate through the plasma when the maximum density is reached. In this sense, IR interferometers operating in the infrared región are themost suitable. With such low wavelengths, mechanical vibrations become an important issue and a complementary interferometer to cancel these vibrations must be used. These arrangements are called two color interferometers. In this paper some measurements that were obtained from the TJ-II double color IR FPGA-based processing system that were never published before are shown and analyzed. The line-averaged electron density is computed in real time (100 μs).

Recently a new class of experiments in the field of surface gravity waves has emerged. These experiments serve as demonstration of an analogy to a broad variety of phenomena in optics and quantum mechanics. In particular, experiments involving Airy water-wave packets were carried out. The Airy wave packets have attracted tremendous attention in optics and quantum mechanics owing to their unique properties, spanning from an ability to propagate along parabolic trajectories without spreading, and to accumulating a phase that scales with the cubic power of time. Non-dispersive Cosine-Gauss wave packets and self-similar Hermite-Gauss wave packets, also well known in the field of optics and quantum mechanics, were recently studied using surface gravity waves as well. These wave packets demonstrated self-healing properties in water wave pulses as well, preserving their width despite being dispersive. Finally, this new approach also allows to observe diffractive focusing from a temporal slit with finite width.

In this paper, a kind of single-walled carbon nanotube nonlinear model is developed, and the strongly nonlinear dynamic characteristics of such carbon nanotubes subjected to random magnetic field are studied. The nonlocal effect of microstructure is considered based on the theory of nonlocal elasticity. The natural frequency of the strongly nonlinear dynamic system is obtained by the energy function method, the drift coefficient and the diffusion coefficient are verified. The stationary probability density function of the system dynamic response is given and the fractal boundary of the safe basin is provided. Theoretical analysis and numerical simulation show that stochastic resonance occurs when varying the random magnetic field intensity. The boundary of safe basin has fractal characteristics and the area of safe basin decreases when the intensity of the magnetic field permeability increases.

In contrast to animals, adult organs in plants are not determined during embryogenesis but gen-erated from meristematic cells as plants advance through development. Plant development in-volves a succession of different phenotypic stages and the transition between these stages is termed phase transition. Phase transitions need to be tightly regulated and coordinated to ensure they occur under optimal seasonal, environmental conditions. Polycarpic perennials transition through vegetative stages and the mature, reproductive stage many times during their lifecycles and, in both perennial and annual species, environmental factors and culturing methods can re-verse the otherwise unidirectional vector of plant development. Epigenetic factors regulating gene expression in response to internal cues and external (environmental) stimuli influencing the plant’s phenotype and development have been shown to control phase transitions. How develop-mental and environmental cues interact to epigenetically alter gene expression and influence these transitions are not well understood and understanding this interaction is important considering the current climate change scenarios, since epigenetic maladaptation could have catastrophic con-sequences for perennial plants in natural and agricultural ecosystems. Here we review studies focussing on the epigenetic regulators of the vegetative phase change and highlight how these mechanisms might act in exogenously induced plant rejuvenation and regrowth following stress.

A high-performance Lead-free Piezoelectric Energy Harvester (LPEH) based on a Ba0.85Ca0.15Ti0.90Zr0.10O3 + CuO 0.3 wt% (BCTZC0.3) composite was fabricated by sintering at 1450℃. The BCTZC0.3 composite, which has an enhanced high-energy-conversion constant (〖d_33×g〗_33), shows improved piezoelectric power-generation performance when compared with conventional piezoelectric energy harvesters. The BCTZC0.3-based LPEH produces instantaneous maximum power of 8.2 mW and an energy density of 107.9 mW/cm3 in a weak magnetic field of 250 μT. This energy harvester can be used to charge a capacitor and operate a wireless sensor network (WSN) system to provide temperature sensing and radio-frequency (RF) transmission in a 250 μT magnetic field. The proposed LPEH is a promising green-energy device for potentially self-powering WSN systems when applied.

We present a numerical study in which large-scale bulk simulations of self-assembled DNA constructs have been carried out with a realistic coarse-grained model. The investigation aims at obtaining a precise, albeit numerically demanding, estimate of the free energy for such systems. We then, in turn, use these accurate results to validate a recently proposed theoretical approach that builds on a liquid-state theory, the Wertheim theory, to compute the phase diagram of all-DNA fluids. This hybrid theoretical/numerical approach, based on the lowest order virial expansion and a nearest-neighbor DNA model, can provide, in an undemanding way, a thermodynamic description of DNA associating fluids that is in semi-quantitative agreement with experiments. We show that the predictions of such scheme are as accurate as the ones obtained with more sophisticated methods. We also demonstrate the flexibility of the approach by incorporating non-trivial additional contributions that go beyond the nearest-neighbor model to compute the DNA hybridization free energy.

Abstract: This study reviewed aspects of the biology of two members of the glucosinolate family, namely sinigrin and glucoraphanin and their anti-tumour and anti-microbial properties. Sinigrin and glucoraphanin are converted by the β-sulphoglucosidase myrosinase or the gut microbiota into their bioactive forms, allyl isothiocyanate (AITC) and sulphoraphanin (SFN) which constitute part of a sophisticated defence system plants developed over several hundred million years of evolution to protect them from parasitic attack from aphids, ticks, bacteria or nematodes. Delivery of these components from consumption of cruciferous vegetables rich in the glucosinolates also delivers many other members of the glucosinolate family so the dietary AITCs and SFN do not act in isolation. In-vitro experiments with purified AITC and SFN have demonstrated their therapeutic utility as antimicrobials against a range of clinically important bacteria and fungi. AITC and SFN are as potent as Vancomycin in the treatment of bacteria listed by the World Health Organisation as antibiotic-resistant "priority pathogens" and also act as anti- cancer agents through the induction of phase II antioxidant enzymes which inactivate potential carcinogens. Glucosinolates may be useful in the treatment of biofilms formed on medical implants and catheters by problematic pathogenic bacteria such as Pseudomonas aeruginosa and Staphylococcus aureus and are potent antimicrobials against a range of clinically important bacteria and fungi. The glucosinolates have also been applied in the prevention of bacterial and fungal spoilage of food products in advanced atmospheric packaging technology which improves the shelf-life of these products.

Luminescence-based sensors for measuring oxygen concentration are widely used both in industry and research due to the practical advantages and sensitivity of this type of sensing. The measuring principle is the luminescence quenching by oxygen molecules, which results in a change of the luminescence decay time and intensity. In the standard approach, this change is related to an oxygen concentration using the Stern–Volmer equation. This equation, which in most of the cases is non-linear, is parametrized through device-specific constants. Therefore, to determine these parameters every sensor needs to be precisely calibrated at one or more known concentrations. This work explores an entirely new artificial intelligence approach and demonstrates the feasibility of oxygen sensing through machine learning. The specifically developed neural network learns very efficiently to relate the input quantities to the oxygen concentration. The results show a mean deviation of the predicted from the measured concentration of 0.5 % air, comparable to many commercial and low-cost sensors. Since the network was trained using synthetically generated data, the accuracy of the model predictions is limited by the ability of the generated data to describe the measured data, opening up future possibilities for significant improvement by using a large number of experimental measurements for training. The approach described in this work demonstrates the applicability of artificial intelligence to sensing technology and paves the road for the next generation of sensors.

This paper is given to the investigation of warm inflation using Modified Chaplygin gas in the background of locally rotationally symmetric Bianchi Identity type I. We find out the field equations and perturbations parameters such as; scalar power spectrum, scalar spectral index, scalar potential and tensor to scalar ratio under slow roll approximation. We find out these parameters in directional of Hubble parameter during the Logamediate inflationary regime in weak and strong case. These comological parameters shows that the anisotropic model is also compatible WMAP$7$ with recent observational data Planck $2018$.

We investigated the structural evolution of the two-phase blends of polycarbonate (PC) and poly(methyl methacrylate) (PMMA) at various blend compositions by simultaneous biaxial stretching using optical microscopy and SEM observation. The spherical PMMA domains and PC matrix in 30/70 PC/PMMA were enlarged uniformly at all in-plane direction, while the anisotropic-shaped co-continuous structure in 50/50 PC/PMMA was deformed to crosshatched one by in-plane bimodal orientation. In 70/30 PC/PMMA, the phase inversion was found to occur by simultaneous biaxial stretching; i.e., the spherical PMMA domains were changed to crosshatched matrix by in-plane bimodal orientation due to coalescence of the PMMA domains during the stretching. Owing to the phase inversion, the surface hardness estimated by pencil hardness test became harder from 2B to 2H with increasing the strain from 1.0 to 2.0.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

proposal for a fundamental theory is described in which classical and quantum physics as a representation of the universe as a gigantic dendrogram are unified. The latter is the explicate order structure corresponding to the purely number-theoretical implicate order structure given by p-adic numbers. This number field was zero-dimensional, totally disconnected, and disordered. Physical systems (such as electrons, photons) are sub-dendrograms of the universal dendrogram. Measurement process is described as interactions among dendrograms; in particular, quantum measurement problems can be resolved using this process. The theory is realistic, but realism is expressed via the the Leibnitz principle of the Identity of Indiscernible. The classical-quantum interplay is based on the degree of indistinguishability between dendrograms (in which the ergodicity assumption is removed). Depending on this degree, some physical quantities behave more or less in a quantum manner (versus classic manner). Ideologically, our theory is very close to Smolin’s dynamics of difference and Rovelli’s relational quantum mechanics. The presence of classical behavior in nature implies a finiteness of the Universe-dendrogram. (Infinite Universe is considered to be purely quantum.) Reconstruction of events in a four-dimensional space type is based on the holographic principle. Our model reproduces Bell-type correlations in the dendrogramic framework. By adjusting dendrogram complexity, violation of the Bell inequality can be made larger or smaller.

It is well established the complex exponential and logarithm are multivalued functions, both failing to maintain most identities originally valid over the positive integers domain. Moreover the general case of complex logarithm, with a complex base, is hardly mentionned in mathematic litterature. We study the exponentiation and logarithm as binary operations where all operands are complex. In a redefined complex number system using an extension of the C field, hereafter named E, we prove both operations always produce single value results and maintain the validity of identities such as log_u (w v) = log_u (w) + log_u (v) where u, v, w in E. There is a cost as some algebraic properties of the addition and subtraction will be diminished, though remaining valid to a certain extent. In order to handle formulas in a C and E dual number system, we introduce the notion of set precision and set truncation. We show complex numbers as defined in C are insufficiently precise to grasp all subtleties of some complex operations, as a result multivaluation, identity failures and, in specific cases, wrong results are obtained when computing exclusively in C. A geometric representation of the new complex number system is proposed, in which the complex plane appears as an orthogonal projection, and where the complex logarithm and exponentiation can be simply represented. Finally we attempt an algebraic formalization of E.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

The study of the brain networks using analysis of electroencephalography (EEG) data based on statistical dependencies (functional connectivity) and mathematical graph theory concepts is common in neuroscience and cognitive sciences for examinations of patient and healthy individuals. The Consciousness Fields according to Taheri theory and applications in the optimization of system under study have been investigated in various studies. In this study, we examine the results of working with Faradarmani Consciousness Field (FCF) in the brain of Faradarmangars. Faradarmangars are one of the necessary components in mind mediation of the function of Faradarmani Consciousness Fields according to Taheri. For this purpose, the functional and effective connectivity and the corresponding brain graphs of EEG from the brain of Faradarmangars is compared with that of non Faradarmangar groups during FCF connection. According to the results of the present study, the brain of the Faradarmangars shows significant decreased activity in delta (BA8), beta2 (BA4/6/8/9/10/11/32/44/47) and beta3 (in 34 of 52 BA) frequency bands mainly in frontal lobe and after that in parietal and temporal lobes in the comparison with the non Faradarmangars. Moreover, the functional and effective connectivity analysis in the frontal network shows dominant multiple decreased connectivity mainly in the case of beta3 frequency band in all parts of the frontal network. On the other hand, the graph theory analysis of the Faradarmangar brain shows an increase in the activity of the O2-T5-F4-F3-FP2-F8 areas and significant decrease in the characteristic path length and increases in global efficiency, clustering coefficient and transitivity. In conclusion, the unique higher graph function efficiency and the reduction in the brain activity and connectivity during the Faradarmani Consciousness Field mind mediation, shown the passive and detector like function of the human brain in this task.

The Inverted F Antenna (IFA) with the parasitic element on a finite conducting plane is proposed in the range frequency of 0.1 to 5.5 GHz and its characteristics are analyzed numerically. In this research, the parasitic element and the main IFA are investigated to obtain the resonance frequency for multiband operation purposes. The parasitic element is placed beneath adjusted to the main IFA to derive more frequency bands. The distance between the parasitic element and main horizontal element extremely affects the performance of the IFA. It is found that when the parasitic element is located closer to the conducting plane, this element is coupled by the current on the conducting plane. Consequently, the return loss bandwidth becomes narrower. Therefore, the gain of the proposed IFA becomes a bit higher. The antenna gain is about 8.21 dB at band #3 (λ_1.747), 7.43 dB at band #5 (λ_2.967) and 8.82 dB at band #6 (λ_4.023). This occurs when the calculation condition is antenna height h1 = 23 mm, h2 = 21 mm, horizontal antenna elements L = 173.2 mm, L1 = 140.9 mm and Lp = 152 mm, shorted element Ls = 30.7 mm, the distance between parasitic element and shorted element pyl = 5 mm. While the size of conducting plane is considered pxp+pxm by pyp+pym as 57.5+57.5 mm by 200+50 mm. In the numerical analysis, the electromagnetic simulator WIPL-D based on Method of Moment is used. The results show that the proposed IFA has UHF and SHF channel receiver which are suitable for advanced wireless service (band #3), mobile phones, Bluetooth, maritime service, radiolocation service (band #5) and radars, mobile phones, commercial wireless LAN (band #6).

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

Framed experiments and games are a useful medium to understand how context affects individual and group decision-making. They are particularly relevant for field research in agriculture, where alternative experimental designs can be costly and unfeasible. After a systematic review of the literature, we found that the volume of published studies employing coordination and cooperation games increased during the 2000-2020 period. In recent years, there has been greater attention given to natural resource management, conservation, and ecology areas, especially in strategic regions for agriculture sustainability. Other games, such as trust and risk games, have come to be regarded as standards of framed field experiments in agriculture. Regardless of sectoral focus, most games' results are subject to internal and external validity criticism. In particular, a significant portion of the games showed potential recruitment biases against women and no opportunities for a continued impact assessment. However, games' validity should be judged on a case-by-case basis. Specific cultural aspects of games might reflect the real context, and generalizing games' conclusions to different settings is often constrained by cost and utility. Overall, games in agriculture could benefit from more significant, frequent, and inclusive experiments and data – all possibilities offered by digital technology. Present-day physical distance restrictions may accelerate this shift. New technologies and engaging ways to approach farmers might represent a turning point for games in agriculture in the 21st century.

The Landauer principle supplies the estimation of the minimal mass of a particle which is capable to record/erase information within a thermal bath at the temperature of T. Particles lighter than ${\tilde{m}}_0=\frac{k_{B}Tln2}{c^2}$will not transform the information to the surrounding bodies and are well expected to be undetectable. The relation of the Landauer principle to the problem of “dark matter” is discussed. The maximal informational content of a particle at rest, estimated as $I_{max}=\frac{m_0{c}^2}{k_{B}Tkn2}$ is introduced. The Landauer principle also allows the estimation of minimal energy of the field which is capable to record/erase 1 bit of information in the surrounding at the temperature of T. The relativistic aspects of the Landauer principle and its relation to the relativistic transformation of temperature are addressed.

An immiscible blend of poly(hydroxy ether of bisphenol-A) (phenoxy) and poly(1,4-butylene terephthalate) (PBT) with phase separation was observed in as-blended samples. However, compatibilization of the phenoxy/PBT blends can be promoted through chemical exchange reactions of phenoxy with PBT upon annealing. In contrast to the as-blended samples, the annealed phenoxy/PBT blends had a homogeneous phase with a single T_g that could be enhanced by annealing at 260°C. Infrared (IR) spectroscopy demonstrated that phase homogenization could be promoted by annealing of the phenoxy/PBT blend, where alcoholytic exchange occurred between the dangling hydroxyl group in phenoxy and the carbonyl group in PBT in the heated blends. The alcoholysis reaction changes the aromatic linkages to aliphatic linkages in carbonyl groups, which initially led to the formation of a graft copolymer of phenoxy and PBT with an aliphatic/aliphatic carbonyl link. The progressive alcoholysis reaction resulted in the transformation of the initial homopolymers into block copolymers and finally into random copolymers, which promoted phase compatibilization in blends of phenoxy with PBT. Due to the fact that the amount of copolymers increased upon annealing, crystallization of PBT was inhibited by alcoholytic exchange in the blends.

Fluxgate magnetometers require calibration methods appropriate to their application levels and particularities; however the development of fully controlled calibration procedures presents a particular challenge regarding the inevitable influence of the local geomagnetic field and other external interferences when a laboratory with magnetically shielded walls is not available. In that context, we discussed the development of an automated calibration method for fluxgate magnetometers, considering those limitations in time and space, and avoiding some of the problems commonly found in other proposed solutions for the same challenge. For this task, we designed and built a new set of high level procedures, electronic systems and software, which perform active testing and automated calibration of fluxgate magnetometers, considering some resource constraints and employing instruments commonly found in electronic calibration laboratories.

In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.

The transmission of light is one of the key optical processes in the terrestrial environment (the atmosphere and underlying surfaces). The dependence of light transmittance on the illumination/observation conditions and optical properties of the atmosphere–underlying system can be studied using the integro-differential radiative transfer equation. However, for numerous applications a set of analytical equations is needed to describe the transmitted light intensity and flux. In this paper, we describe various analytical techniques to study light transmittance through light scattering and absorbing media. A physical significance and improved mathematical accuracy of approximations are provided using the analytical models for the diffusion exponent, average cosine of the light field, spherical and plane albedos. The accuracy of various approximations is studied using exact radiative transfer calculations with various scattering phase functions, single-scattering albedos, observational conditions, and optical depths.

In quantum field theory (QFT), it is well known that when Feynman diagrams containing loops are evaluated to account for self interactions, probability amplitude comes out to be infinite which is physically not admissible. So, to make the QFT convergent, various renormalization methods are conventionally followed in which an additional (infinite) counter term is postulated which neutralizes the original infinity generated by diagram. The resulting finite values of amplitudes have agreed with experiments with surprising accuracy. However, proponents of renormalization methods acknowledged that this ad-hoc procedure of subtraction of infinity from infinity to reach at a finite value is not at all satisfactory and there is no physical basis for bringing in the counter term. So, it is desirable to establish a method in QFT which does not generate any infinite term (thus not requiring renormalization), but which predicts same results as conventional methods do. In this paper, we describe such a technique taking self interaction quantum electrodynamics diagram representing electron or photon self energy. In our method, no problem of infinity arises and hence renormalization is not necessary. Still, the dependence of calculated probability amplitude on physical variables in our technique comes out to be same as conventional methods. Using similar procedure, we hope, the problem of non-renormalizability of quantum gravity may be solved in future.

Selective laser melting is an emerging Additive Manufacturing (AM) technology for metals. Intricate three-dimensional parts can be generated from the powder bed by selectively melting the desired location of the powders. The process is repeated for each layer until the part is built. The necessary heat is provided by a laser. Temperature magnitude and history during SLM directly determine the molten pool dimensions, thermal stress, residual stress, balling effect, and dimensional accuracy. Laser-matter interaction is a crucial physical phenomenon in the SLM process. In this paper, five different heat source models are introduced to predict the three-dimensional temperature field analytically. These models are known as steady state moving point heat source, transient moving point heat source, semi-elliptical moving heat source, double elliptical moving heat source, and uniform moving heat source. The analytical temperature model for all of the heat source models are solved using three-dimensional differential equation of heat conduction with different approaches. The Steady state and transient moving heat source are solved using separation of variables approach. However, the rest of models are solved by employing the Green’s functions. Due to the high magnitude of the temperature in the presence of the laser, the temperature gradient is usually high which has a substantial impact on thermal material properties. Consequently, the temperature field is predicted by considering the temperature sensitivity thermal material properties. Moreover, due to the repeated heating and cooling, the part usually undergoes several melting and solidification cycles, this physical phenomenon is considered by modifying the heat capacity using latent heat of melting. Furthermore, the multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the layers have an impact on heat transfer mechanisms. The proposed temperature field models based on different heat source approaches are validated using experimental measurement of melt pool geometry from independent experimentations. The detailed explanation of the comparison of models is also provided. Moreover, the effect of process parameters on the balling effect is also discussed.

The important sampling parameters of a headspace solid phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS) procedure, extraction temperature, extraction time and sample volume were optimized to quantify 23 important impact odorants in reduced alcohol red and white wines. A three-factor design of Box-Behnken experiments was used to determine optimized sampling conditions for each analyte, and a global optimized condition at every ethanol concentration of interest determined using a desirability function that accounts for a low signal response for compounds. Shiraz and Chardonnay wines were dealcoholized from 13.7 and 12.2% v/v ethanol respectively, to 8 and 5% v/v, using a commercially available membrane-based technology. A sample set of the reduced alcohol wines were also reconstituted to their natural ethanol level to evaluate the effect of ethanol content reduction on volatile composition. The three-factor Box-Behnken experiment ensured an accurate determination of the headspace concentration of each compound at each ethanol concentration, allowing comparisons between wines at varying ethanol levels to be made. Overall, the results showed that the main effect of extraction temperature was considered the most critical factor when studying the equilibrium of reduced alcohol wine impact odorants. The impact of ethanol reduction upon the concentration of volatile compounds clearly resulted in losses of impact odorants from the wines. The concentration of most analytes decreased with dealcoholization compared to that of the natural samples. Significant differences were also found between the reconstituted volatile composition and 5% v/v reduced alcohol wines, revealing that the dealcoholization effect is the result of a combination between the type of dealcoholization treatment and reduction in wine ethanol content.

The growing market penetration of heat pumps indicates the need for a performance test method which better reflects the dynamic behavior of heat pumps. In this contribution, we developed and implemented a dynamic test method for the evaluation of the seasonal performance of heat pumps by means of laboratory testing. Current standards force the heat pump control inactive by fixing the compressor speed. In contrast, during dynamic testing, the compressor runs unfixed while the heat pump is subjected to a temperature profile. The profile consists of the different outdoor temperatures of a typical heating season based on the average European climate and also includes temperature changes to reflect the dynamic behavior of the heat pump. The seasonal performance can be directly obtained from the measured heating energy and electricity consumption making subsequent data interpolation and recalculation with correction factors obsolete. The method delivers results with high precision and high reproducibility and could be an appropriate method for a fair rating of heat pumps.

This paper presents a 612–1152 MHz Injection Locked Frequency Multiplier (ILFM). The proposed ILFM is only used for sending an input signal to the receiver in the I/Q mismatch calibration mode. Using the Phase-Locked Loop (PLL) to calibrate the receiver places a burden on this system due to the extra area required and power consumption. Instead of the PLL, to satisfy high frequency, low jitter, and low area, a Ring Oscillator is proposed. The free-running frequency of the ILFM is automatically digitally calibrated to reflect the frequency of the injected signal from the harmonics of the reference clock. To control the frequency of the ILFM, the load current is digitally tuned with 6-bit digital control signal. The proposed ILFM locks to the target frequency using a digitally controlled Frequency Locked Loop (FLL). This chip is fabricated using 1-poly 6-metal 0.18 µm CMOS and achieve the wide tuning range of 612–1152 MHz. The power consumption is 0.95 mW from a supply voltage of 1.8 V. The measured phase noise of the ILFM is −108 dBc/Hz at a 1 MHz offset.

Non-viral gene carriers because of their limited side effects, biocompatibility, simplicity and taking the advantages of electrostatic interactions have shown noticeable potential in gene delivery. The low transfection rate of non-viral vectors under physiological conditions is a significant issue. Here, the aim of this study was to investigate the efficacy of hydrophilic and hydrophobic groups on gene carriers such as two synthesized amphiphilic polymer of dextran-stearic acid-spermine (DSASP) with verified lipid and amine conjugations that associated with Fe3O4 superparamagnetic nanoparticles to promote the target delivery and decrease the transfection time using static magnetic field. Our findings illustrate that magnetic nanoparticles are spherical with positive surface charges and superparamagnetic behaviors. The DSASP–pDNA/MNPs offered a strong pDNA condensation, protection against DNase degradation, significant cell viability in HEK 293T cells and. Although conjugations of spermine play a critical role in transfection efficiency, amphiphilic polymer with more derivatives of stearic acid showed better transfection yields. Therefore, DSASP amphiphilic magnetic carriers offer new insights for gene delivery due to the amine contents and ameliorate the uptake of complexes via cell membrane based on its hydrophilic surface.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

We present a thermodynamic approach in modeling the evolution of the universe based on a theory that space consists of energy quanta, the spaceons. From wave-particle duality, they can be treated as an ideal gas. The model is similar to the Big Bang but without Inflation. It provides an insight into the nature of dark energy and dark matter, and an explanation for the accelerated expansion of the universe. The universe started from an atomic size volume of spaceons at very high temperature and pressure. Upon expansion and cooling, phase transitions occurred resulting in the formation of fundamental particles, and matter. These nucleate and grow into stars, galaxies, and clusters due to the action of gravity. From the cooling curve of the universe we constructed a thermodynamic phase diagram of cosmic composition, from which we obtained the correlation between dark energy and the energy of space. Using Friedmann’s equations, our model fits well the WMAP data on cosmic composition with an equation of state parameter, w= -0.7. The dominance of dark energy started at 7.25 x 10⁹ years, in good agreement with BOSS measurements. The expansion of space is attributed to a scalar quantum space field. Dark Matter is identified as a plasma form of matter similar to that which existed during the photon epoch, prior to recombination. The thermodynamics of expansion of the universe was adiabatic and decelerating during the first 7 billion years after the Big Bang; it accelerated thereafter. A negative pressure for Dark Energy is required to sustain the latter. This is consistent with the theory of General Relativity and the law of conservation of energy. We propose a mechanism for the acceleration as due to consolidation of matter forming Dark Energy Stars (DES) and other compact objects. The resulting reduction in gravitational potential energy feeds back energy for the expansion. Space will continue to expand and dark energy will undergo phase transition to a Bose-Einstein condensate, a superfluid form of matter. Self-gravitation can cause a bounce and start a new Big Bang. We show how the interplay of gravitational and space forces leads to a cyclic, maybe eternal, universe.

Abstract— Flight Control System is an integrated avionics system equipped with the minimum required components for an autonomous flight. This paper focuses on the Hardware Design of the Flight Control System and presents specific details of the components and its interface. The system architecture is based on Field Programmable Gate Array and Digital Signal Processor. Employing these two processors in the flight control system would improve the Flight Control System performance in terms of fast sequential processing of high-level control algorithms. In addition to Field Programmable Gate Array and Digital Signal Processor, the flight control computer system will also make use of Global Positioning System and Micro Electro Mechanical System sensors. The project will be implemented using Altera’s System On Programmable Chip builder, currently known as Qsys – Platform Designer implemented in Quartus-II. The system employs Nios-II processor which is 32-bit soft-core embedded-processor architecture designed especially for the Altera’s family of Field Programmable Gate Array. From conceptualization to final design, this paper presents the functionality of the different modulus and complex interfaces employed in this Flight Control System.

The application of electrospray ionization mass spectrometry (ESI-MS) as a direct method for detecting reactive intermediates is a technique of developing importance in the routine monitoring of solution-phase reaction pathways. Here, we utilize a novel on-line photolysis ESI-MS approach to detect the photoproducts of riboflavin in aqueous solution under mildly alkaline conditions. Riboflavin is a constituent of many food products, so its breakdown processes are of wide interest. Our on-line photolysis setup allows for solution-phase photolysis to occur within a syringe using UVA LEDs, immediately prior to being introduced into the mass spectrometer via ESI. Gas-phase photofragmentation studies via laser-interfaced mass spectrometry of deprotonated riboflavin, [RFH], the dominant solution-phase species under the conditions of our study, are presented alongside the solution-phase photolysis. The results obtained illustrate the extent to which gas-phase photolysis methods can inform our understanding of the corresponding solution-phase photochemistry. We determine that the solution-phase photofragmentation observed for [RFH] closely mirrors the gas-phase photochemistry, with the m/z 241 ion being the only major condensed-phase photoproduct. Further gas-phase photoproducts are observed at m/z 255, 212, and 145. The value of exploring both the gas- and solution-phase photochemistry to characterize photochemical reactions is discussed.

Recently, Indium Tin Oxide, a highly transparent, well conductive, and CMOS-compatible material, has been paying strong attention to the thermo-optic controlled silicon photonics industry because it allows a miniature of the gap between the core silicon and the heater, thus enabling reducing the electric power consumption and enhancing the switching speed. In this article, we propose an ultralow loss and small-size ITO microheater for the phase shift tuning. The designated microheater is manipulated in realizing a numerical co-design of compact and high bandwidth three-mode converter and three-mode selective router. Simulation results illustrate the 3-dB bandwidth for the three-mode converter and three-mode selective router as much as 100-nm and 40-nm during crosstalk under -25 dB, respectively. Besides, co-designed devices attain relatively large fabrication tolerances corresponding to width and height tolerances of ±50 nm and ±5 nm. In addition, the proposed devices consumed less than 90 mW total power consumption and took a fast switching time below 8 μs. Moreover, both two co-designs can be integrated into an estimated compact footprint of 8 μm2160 μm. Such excellent performances demonstrate the attractive potential of ITO as low-loss thermo-optic phase shifters and open an alternative way for enabling ultrafast and high-speed mode division multiplexing systems and very large-scale photonic integrated circuits.

This paper results from our investigation into novel means of electromagnetic propulsion. It requires the basis of our claims to be put on a sound theoretical footing regarding the purported momentum exchange with the electromagnetic field. One of these concerns is the huge discrepancy between the energy density of the Zeropoint and its purported manifestation as the Cosmological Constant. Here we state that it is manifestly wrong to introduce the zeropoint at zero order into the stress-energy tensor, because it is something which describes zero particle count. As a fluctuation, it belongs in a higher order Taylor expansion in frequency of the stress-energy tensor. Furthermore in the 3^rd order in the Einstein constant our procedure is some 9 orders of magnitude too small. We make up this difference by suggesting that vacuum energy is much higher still and that more degrees of freedom exist in physics beyond the Standard Model or that there is interaction energy between the modes.

Poly(hydroxyalkanoates) (PHAs) are currently considered competent candidates to replace traditional plastics in several market sectors. However, commercial PHA grades exhibit unsatisfactory smell that can negatively affect the quality of the final product. The cause of this typical rancid odour is attributed to oxidized cell membrane glycolipids, coming from Gram negative production strains, which remain frequently attached to PHAs granules after extraction. The aim of this research is the development of customised PHA nano-biocomposites for industrial applications containing organo-modified nanoclays with high adsorption properties able to capture volatile compounds responsible of the displeasing fragrance in PHAs. To this end, a methodology for the detection and identification of the key volatiles released due to oxidative degradation of PHAs has been established using a headspace solid-phase microextraction technique. We report the development of nine nano-biocomposite materials based on three types of commercial PHA matrices loaded with three species of nanoclays which represent a different polar behaviour. It has been demonstrated that although the reached outcome effect depends on the volatile nature, natural sepiolite (T2) might result in the most versatile candidate for all PHA matrices selected.

Despite the successes earned in cataloguing and finding the role of the most of molecular components in living matter, the “biochemical and molecular” perspective, popular in biology, medicine and genetics, is unable to give account for crucial topics as the faculty of living systems to “feel”, to “perceive” what a given stimulus implies (means, indeed) for their survival. Condensed matter physics too, if bounded to a local, short-range, and perturbative approach, fails dramatically. This is also due to the role commonly assigned to water – actually the main constituent of living matter – deemed for long time to be merely chemical (as “solvent” or a reactant/product). Nonetheless, today many evidences show how living matter can be right conceived as a super-structured coherent water-based matrix, suggesting that the characterization of bio(electro)chemical and physical processes undertaken at molecular level in living matter, would let us unable to answer a question like this: what allows an amoeba, moreover without any neurons, to “know” to get closer to a nutrient or escape away from a toxin? I propose that to pursue such a fundamental inquiry it’s necessary an essentially relational approach, that is: to consider the living being at its grounding as the outcome of a physical history of relationships where symmetry-breakings, dissipation and coherence yield the emergence of the living state of matter, conceivable only as a time-dependent open process, and not as a portraited “body”. The effective tools to build up such an approach may be retrieved in far-from-equilibrium thermodynamics (TD), symmetry-breakings and gauge-fields theory, science of complexity, within the framework of a Quantum Field Theory. Indeed, within a field-view of matter, and of water especially, as it has been developed by a Quantum Electrodynamic (QED) description of condensed matter, it’s possible to give account for a physical basis too such an epistemologically elusive, though crucial, feature of living systems (i.e.: perception and meaning). The emerging landscape allows some important meditations about adaptation, evolution, ecodynamics, and about different conceptions of complexity and “information” in living realm. Furthermore, some neuroscientific themes like consciousness, qualia and their links to artificial intelligence could be supplied with due insights.

The hybrid personal cooling system (HPCS) consisted of ventilation fans and phase change materials (PCMs) covered with insulation pads is a promising wearable cooling system to mitigate heat strain and heat-related illnesses of occupational workers with heavy labor in hot environments. Effects of clothing characteristics (e.g., thermal resistance of insulation pads, latent heat and melting temperature of PCMs) on the thermal performance of the HPCS have been investigated in detail in our previous study. Apart from the aforementioned factors, environmental conditions, i.e., environmental temperature and relative humidity, also significantly affect the thermal performance of the HPCS. In this paper, a numerical parametric study was performed to investigate the effects of the environmental temperature and relative humidity (RH) on the thermal management of the HPCS. Five levels of air temperature under environmental RH=50% were chosen (i.e., 32, 34, 36, 38 and 40 ºC) to study the impact of environmental temperature on the HPCS’s cooling performance. In addition, four levels of environmental RH at ambient temperatures of 36 and 40 ºC were selected (i.e., 30, 50, 70 and 90%) to examine the effect of RH on cooling performance of the HPCS. Results show that high environmental temperatures could accelerate the PCM melting process and thereby weaken the cooling performance of HPCS. In the moderately hot environment (36 °C), the HPCS presented good cooling performance with the maximum core temperature at around 37.5 °C during excise when the ambient RH≤70%, whereas good cooling performance could be only seen under RH≤50% in the extremely hot environment (40 °C). Thus, it may be concluded that the maximum environmental RH for the HPCS exhibiting good cooling performance decreases with the increase in the environmental temperature.

Microplastics (MPs) quantification in benthic marine sediments is typically performed by time-consuming and moderately accurate mechanical separation and microscopy detection. In this paper we describe the results of our innovative Polymer Identification and Specific Analysis (PISA) of microplastic total mass, previously tested on either less complex sandy beach sediment or less demanding (because of the high MPs content) wastewater treatment plant sludges, applied to the analysis of benthic sediments from a sublittoral area north-west of Leghorn (Tuscany, Italy). Samples were collected from two shallow sites characterized by coarse debris in a mixed seabed of Posidonia oceanica, and by a very fine silty-organogenic sediment, respectively. After sieving at &lt;2 mm the sediment was sequentially extracted with selective organic solvents and the two polymer classes polystyrene (PS) and polyolefins (PE and PP) were quantified by pyrolysis-GC/MS. A contamination in the 8-65 ppm range by PS could be accurately detected. Acid hydrolysis on the extracted residue to achieve total depolymerization of all natural and synthetic polyamides, tagging of all aminated species in the hydrolyzate with a fluorophore, and reversed-phase HPLC (RP-HPLC) analysis, allowed to quantify within the 137-1523 ppm range the individual mass of contaminating Nylon 6 and Nylon 6,6, based on the detected amounts of the respective monomeric amines 6-aminohexanoic acid (AHA) and hexanediamine (HMDA). Finally, alkaline hydrolysis of the residue from acid hydrolysis followed by RP-HPLC analysis of the purified hydrolysate showed contamination by polyethylene terephthalate (PET) in the 12.1-2.7 ppm range, based on the content of its comonomer, terephthalic acid.

The Chang’e-4 (CE-4) lunar rover, equipped with The Visible and Near-IR Imaging Spectrometer(VNIS) which based on acousto-optic tunable filter spectroscopy, was launched to the far side of the moon on December 8, 2018. The detection band of VNIS ranges from 0.45 to 2.4μm. Because of the weak reflection of infrared radiation from the lunar surface, a static electronic phase-locked acquisition method is adopted in the infrared channel for signal amplification. In this paper, full-link simulations and modeling are conducted of the infrared channel information flow of the instrument. The signal/noise characteristics of VNIS are analyzed in depth, and the signal-to-noise(SNR) ratio prediction and laboratory verification are presented. On January 4, 2019, the VNIS started working successfully and acquired high-resolution spectrum data of the far side of the moon for the first time. Through analysis, the SNR ratio is in line with predictions, and the data obtained by VNIS in orbit are consistent with the information model proposed in this paper.

Climate change is expected to increase the frequency and severity of abiotic stresses that lead to loss of crop yield. We investigated the effect of salinity (S), short episodes of high temperature (HS) and combination of S+HS at the reproductive phase on dead pericarps properties and yield of the crop plant Brassica juncea. Three intervals of HS resulted in massive seed abortion; seeds from salt-treated plants germinated poorly. Pericarp extracts of salt-treated plants reduced seed germination of B. juncea; all pericarp extracts completely inhibited seed germination of tomato and Arabidopsis; removal of pericarp extracts restored seed germination. HS reduced all metabolites accumulated in dead pericarps, except for upregulation of isomaltose and cellobiose. Salt induced alteration in metabolite levels including increase in proline, reduction in TCA intermediates and changes in phytohormone levels. Proteome analysis revealed hundreds of proteins stored in dead pericarps whose levels and composition were altered under salt stress. The integration of metabolic and proteomic data showed that changes in metabolites were highly correlated with changes in proteins involved in their biosynthetic pathways. Thus, besides providing a physical shield for seed/embryo protection dead pericarps store beneficial substances whose levels, composition and biological function are altered under stress, further highlighting the elaborated function of dead organs enclosing embryos in seed biology and ecology. The detrimental effect of HS on crop production might have implications for global food security in the face of climate change.

Space-based Interferometric Synthetic Aperture Radar (InSAR) applications have been widely used to monitor the cryosphere over past decades. Because of temporal decorrelation, interferometric coherence often severely degrades on fast moving glaciers. In addition, higher sensitivity ambiguity occurs in large baseline configurations, which are needed for extracting topographic information over low relief areas such as the surface of a glacier. TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) observations, which overcome the temporal decorrelation because of their simultaneous measurements by two satellite constellations, have used a short baseline sufficient for generation of excellent digital elevation models in most locations around the world. However, it remains difficult to estimate detailed topographic characteristics over low slope glacier surfaces because of the relatively less sensitive height ambiguity from the small baselines. In this study, we used the TanDEM-X pursuit monostatic mode with large baseline formation following a scientific phase timeline to develop highly sensitive topographic elevation models of the Petermann Glacier of Northwest Greenland. As expected, coherent interferometric phases (> 0.8) were well maintained over the glaciers despite their fast movement thanks to the nearly simultaneous TanDEM‐X measurements. The height ambiguity, which defined as the altitude difference correspondent to phase change of flattened interferogram, of the dataset was 10.63 m, which is favorable for extracting topography in a low relief region. We validated the TanDEM‐X derived glacial topography by comparing it to the SAR/Interferometric radar altimeter observations acquired by CryoSat‐2 and the IceBridge Airborne Topographic Mapper laser altimeter measurements. Both observations showed very good correlation within a few meters of the offsets (‐12.5 – ‐3.1 m) with respect to the derived glacial topography. Because of highly sensitive ambiguity, we could successfully extract detailed geomorphological features on the glaciers. Routine TanDEM-X observations will be very useful to better understand the dynamics of glacial movements and topographic change.

A radical, albeit pragmatic protocol for experimental access to putative String/M-theoretic, Einstein Unified Field Mechanical (UFM) additional dimensionality (XD) of the brane-bouquet bulk is presented. If successful, results demonstrate the existence dimensionality beyond the metric of observed physical reality provided by the Standard Model (SM) of particle physics and Cosmology. Quantum Mechanics (QM), as well-known is incomplete and further, should no longer be considered the basement of reality; meaning, Locality and Unitarity – the fundaments of quantum theory are an insufficient basis for extending the representation of reality. A seminal model of Tight Bound States (TBS) below the lowest Bohr orbit in the hydrogen atom, proposed by Vigier, is extended to a Kaluza-Klein-like (KK) cyclical tier of XD hyperspherical cavities defined within a manifold of uncertainty (MOU) of finite radius up to the semi-quantum limit, predicting, within its domain, new spectral lines in Hydrogen. The proposed protocol for this process, with phase modifications, provides efficacy of large-scale additional dimensionality (LSXD) of the brane bulk; XD-LSXD incursion duality accesses nonlocal Einsteinian UFM phenomena, leading to myriad new classes of technological innovation.

We describe the direct formation of mixed-phase (1T and 2H) MoS2 layers on Si as a photocathode via atomic layer deposition (ALD) for application in the photoelectrochemical (PEC) reduction of water to hydrogen. Without typical series-metal interfaces between Si and MoS2, our p-Si/SiOx/MoS2 photocathode showed efficient and stable operation in hydrogen evolution reactions (HERs). The resulting performance could be explained by spatially genuine device architectures in three dimensions (that is, laterally homo and vertically heterojunction structures). The ALD-grown MoS2 overlayer with the mixed-phase 1T and 2H homojunction passivates light absorber and surface states and functions as a monolithic structure for effective charge transport within MoS2. It is also beneficial in the operation of p-i-n heterojunctions with inhomogeneous barrier heights due to the presence of mixed-phase cocatalysts. The effective barrier heights reached up to 0.8 eV with optimized MoS2 thicknesses, leading to a 670 mV photovoltage enhancement without employing buried Si p-n junctions. The fast-transient behaviors via light illumination show that the mixed-phase layered chalcogenides can serve as efficient cocatalysts by depinning the Fermi levels at the interfaces. A long-term operation of ~ 70 h was also demonstrated in a 0.5 M H2SO4 solution.

We study the resonant dipole-dipole interaction energy between two uniformly accelerated identical atoms, one excited and the other in the ground state, prepared in a correlated Bell-type state, and interacting with the scalar field or the electromagnetic field nearby a perfectly reflecting plate. We suppose the two atoms moving with the same uniform acceleration, parallel to the plane boundary, and that their separation is constant during the motion. We separate the contributions of vacuum fluctuations and radiation reaction field to the resonance energy shift of the two-atom system, and show that Unruh thermal fluctuations do not affect the resonance interaction, which is exclusively related to the radiation reaction field. However, nonthermal effects of acceleration in the radiation-reaction contribution, beyond the Unruh acceleration-temperature equivalence, affect the resonance interaction energy. By considering specific geometric configurations of the two-atom system relative to the plate, we show that the presence of the mirror significantly modifies the resonance interaction energy between the two accelerated atoms. In particular, we find that new and different features appear with respect to the case of atoms in the free space, related to the presence of the boundary and to the peculiar structure of the quantum electromagnetic field vacuum in the locally inertial frame. Our results suggest the possibility to exploit the resonance interaction between accelerated atoms, as a probe for detecting the elusive effects of atomic acceleration on radiative processes.

Since its 2013 emergence in the Americas, chikungunya virus (CHIKV) has posed a serious threat to public health. Early and accurate diagnosis of the disease, though currently lacking in clinics, is integral to enable timely care and epidemiological response. We developed a dual detection system: a CHIKV antigen E1/E2-based enzyme-linked immunosorbent assay (ELISA) and a lateral flow test using high-affinity anti-CHIKV antibodies. The ELISA was validated with 100 PCR-tested acute Chikungunya fever samples from Honduras. The assay had an overall sensitivity and specificity of 51% and 96.67%, respectively, with accuracy reaching 95.45% sensitivity and 92.03% specificity at a Ct cutoff of 22. As the Ct value increased from 22, ELISA sensitivity decreased. We then developed and validated two lateral flow tests using independent antibody pairs. The sensitivity and specificity reached 100% for both lateral flow tests using 39 samples from Colombia and Honduras at Ct cutoffs of 20 and 27, respectively. For both lateral flow tests, sensitivity decreased as the Ct increased after 27. Because CHIKV E1/E2 are exposed in the virion surfaces in serum during the acute infection phase, these sensitive and specific assays demonstrate opportunities for early detection of this emerging human pathogen.

In this work, a small-strain phase-field model is presented, which is able to predict crack propagation in systems with anisotropic brittle and ductile constituents. To model the anisotropic brittle crack propagation, an anisotropic critical energy release rate is used. The brittle constituents behave linear-elastically, in a transversely isotropic manner. Ductile crack growth is realised by a special crack degradation function, depending on the accumulated plastic strain, which is calculated by following the J2-plasticity theory. The mechanical jump conditions are applied in solid-solid phase transition regions. The influence of the relevant model parameters on a crack, propagating through a planar brittle-ductile interface, and furthermore a crack developing in a domain with a single anisotropic brittle ellipsoid, embedded in a ductile matrix, is investigated. We demonstrate that important properties, concerning the mechanical behaviour of grey cast iron, such as the favoured growth of cracks along the graphite lamellae and the tension-compression load asymmetry of the stress-strain response, are covered by the model. The behaviour is analysed on basis of a simulation domain consisting of three differently oriented elliptical inclusions, embedded in a ductile matrix, which is subjected to tensile and compressive load. The used material parameters correspond to graphite lamellae and pearlite.

Few switching transitions in high power and medium voltage application of Power converters are desirable. The selective harmonics elimination (SHE) pulse width modulation offers a better quality waveform with lower switching transitions and hence lower switching losses. The SHE is a pre-programmed modulation technique where certain amounts of lower order harmonics are removed and fundamental voltage is controlled. After Fourier analysis of output waveform, a set of nonlinear transcendental equations is obtained which exhibits, multiple, unique or no solution in different range of modulation index (MI). In this paper, an iterative method based on the Jacobian estimate is proposed to solve a highly non-linear set of SHE equations. The proposed technique is easy in implementation and can solve a large number of such equations as computation of the Jacobian matrix in the subsequent iteration is estimated from the previous values. Moreover, the proposed method also removes the singularity problem, especially for large SHE equations. High accuracy in the initial guess is also not essential for this method and can converge to the solution with any random initial guess. The computational and simulation results are given to validate the concept. The hardware result is provided to confirm the computational and simulation results.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

A new formulation for a proposed solution to the 3D Navier-Stokes Equations in cylindrical co-ordinates coupled to the continuity and level set convection equation is presented in terms of an additive solution of the three principle directions in the radial, azimuthal and z directions of flow and a connection between the level set function and composite velocity vector for the additive solution is shown. For the case of a vertical tube configuration with small inclination angle, results are obtained for the level set function defining the interface in both the radial and azimuthal directions. It is found that the curvature dependent part of the problem alone induces sinusoidal azimuthal interfacial waves wheras when the curvature together with the equation for the composite velocity is considered oscillating radial interfacial waves occur. The implications of two extremes indicate the importance of looking at the full equations including curvature.

A phenomenological constitutive model is developed to describe the uniaxial transformation ratcheting behaviors of super–elastic shape memory alloy (SMA) by employing a cosine–type phase transformation equation with the initial martensite evolution coefficient that can capture the feature of the predictive residual martensite accumulation evolution and the nonlinear hysteresis loop on a finite element (FE) analysis framework. The effect of the applied loading level on transformation ratcheting are considered in the proposed model. The evolutions of transformation ratcheting and transformation stresses are constructed as the function of the accumulated residual martensite volume fraction. The FE implementation of the proposed model is carried out for the numerical analysis of transformation ratcheting of the SMA bar element. The integration algorithm and the expression of consistent tangent modulus are deduced in a new form for the forward and reverse transformation. The numerical results are compared with those of existing model and the experimental results to show the validity of the proposed model and its FE implementation in transformation ratcheting. Finally, a FE modeling is established for a repeated preload analysis of SMA bolted joint

We show that quantum mechanics can be constructed as a classical field theory that correctly describes all basic quantum effects, by combining the Maxwell and Dirac equations. It is shown that for a self-consistent union of the Maxwell and Dirac equations into a unified classical field theory, it is necessary to introduce an additional short-range tensor field, which compensates the intrinsic electrostatic field of the electron wave inside the atom. For the combined Maxwell-Dirac field, the stress-energy tensor is constructed. We show that in the nonrelativistic limit this theory naturally transforms into the self-consistent Maxwell-Pauli theory and allows describing all basic quantum effects in the framework of classical field theory without any quantization.

Although good field emission from graphene has been demonstrated from a wide variety of different microfabricated structures, very few of them can be used to improve the design of cold field emitters for electron microscopy applications. Most of them consist of densely packed nano-emitters, which produce a large array of defocused overlapping electron beams, and therefore cannot be subsequently focused down to a single nanometer electron probe. This paper reviews the kind of single-tip cathode structures suitable in cold field emission guns for instruments such as scanning electron microscopy, transmission electron microscope or scanning transmission electron microscopy, and reviews progress in fabricating them from graphene-based materials.

One of the intriguing recent results in the field of high-entropy alloys is the discovery of single-phase equiatomic multi-component Laves intermetallics. However, there is no clear understanding that a combination of chemical elements will form such high-entropy compounds. Here we contribute to understanding this issue by modifying the composition of duodenary TiZrHfNbVCrMoMnFeCoNiAl (12x) alloy in which we recently reported the fabrication of hexagonal C14 Laves phase. We consider three alloys based on 12x: 7x=12x-VCrMoMnFe, 12x+Sc, 12x+Be and observe that all of them crystalize with the formation of C14 Laves phase as a dominant structure. We report that 12x+Be alloy reveals single-phase C14 structure with very high concentration of structural defects and ultra-fine dendritic microstructure with almost homogenous distribution of the constituted elements over the alloy matrix. The 7x and 12x+Sc alloys contain C14 as a main phase and unknown impurity phases. To characterize the materials, we examine their heat capacity, electrical conductivity and magnetic properties. The measurements reveal that the Laves phases are Curie-Weiss paramagnets, which demonstrate metallic conduction; 7x and 12x alloys also reveal a pronounced Kondo-like anomaly. Analysis of experimental data as well as ab initio calculations suggests that chemical complexity and compositional disorder cause strong s-d band scattering and thus the rather high density of d-states in the conduction band. Analysis of the results suggests that the mechanism of Laves phase formation in multicomponent multi-principal element metallic alloys is may be the same as in polydisperse hardspheres mixtures. Another important conclusion is that the configurational entropy is a negligible factor in the stabilization of multi-element Laves phases.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

Large inconsistencies in the outcome of precise measurements of Newtonian gravitational ‘constant’ were identified throughout more than three hundred experiments conducted up to date. This paper illustrates the dependency of the Newtonian gravitational parameter on the curvature of the background and the associated field strength of vacuum energy. Additionally, the derived interaction field equations show that boundary interactions and spin-spin correlations of vacuum and conventional energy densities contribute to the emergence of mass. Experimental conditions are recommended to achieve consistent outcomes of the parameter precision measurements, which can directly falsify or provide confirmations to the presented field equations.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

This research takes Cuiwei Village in Qianshan District of Zhuhai City as an example. Through field research, the village is investigated and analyzed, and the street scale, spatial structure, functional characteristic streets, internal commercial distribution forms, and functions of Cuiwei Historic District are studied. analysis. On this basis, based on the convex space method and the line-of-sight analysis method in the space syntax theory, with the help of Depthmap software, the complex street node, that is, the space of the two nodes A and B, is established through the establishment of a visual field model. It includes the analysis of the integration degree of the horizon, the concentration of the horizon, the connection value of the horizon and the spatial characteristics of the historical area, as well as the traditional buildings that are the most representative of the village, namely the Three Kings Temple and the Webster's Mansion. When R=N and radius R=3, observe the changes in the two parameters of the visual integration and visual depth of the two historical buildings. And with the help of Baidu Time Machine photos in different periods to observe and record the changes in the store and the characteristics of people's behavior, and draw conclusions.

CrHZSM-5 was placed in an electric field with appropriate strength in a quartz packed bed reactor with CO2 as oxidant to analyze its catalytic activity. Olefin yield increases with decrease in band gap since lattice oxygen mobility increases by reducing band gap. Fermi level change at the catalyst surface affects the catalytic activity. One way to change Fermi level is use electric field. In high voltage electric field, energy band was curved, bending of the energy band promoted the activity and Fermi level position is increasing. The CCD experiments were carried out with Design-Expert 7.3 software to determine the interaction between four operating variables, namely: temperature, electrical current, gap distance and metal loading. The levels of the independent variables were: temperature (550-700 °C), electrical current (0-12 mA), gap distance (6-14 mm), metal loading (0.5-7.5 %wt.). The conversion of LPG (Liquefied petroleum gas) was greatly increased by weak and effective application of an electric field to the catalyst bed. The obtained results indicated that the maximum yield value (46.94%) can be achieved under 673.66 °C, input electrical current of 11.01 mA, gap distance of 6.55 mm and metal loading of 3.98 wt.%.

The expansion of concrete subjected to extreme elevated temperature is linked with intricate micro-structural variations, such as the transformation of the constituent phases. This study proposes a model to predict the thermal expansion of cement paste and concrete considering micro-structural changes under elevated temperatures ranging from 20°C to 800°C. The model presented can consider characteristics of various aggregates in the calculation of thermal expansion for concrete. The model is a combination of a multi-scale stoichiometric model and a multi-scale composite model. At the cement paste level, the model satisfactorily predicted a test result. At concrete level, upper bounds from the model were matched relatively well with test results by previous researcher. If the mechanical properties, such as elastic modulus (E), Poisson’s ratio (ν), and thermal deformation, of the aggregates used in concrete are given, it is likely that the model will reasonably predict experimental results.

Due to the increasing global importance of decarbonizing human activities, especially the production of electricity, the optimal deployment of renewable energy technologies will play a crucial role in future energy systems. To accomplish this, particular attention must be accorded to the geospatial and temporal distribution of variable renewable energy sources (VRES) such as wind and solar radiation in order to match electricity supply and demand. This study presents a techno-economical assessment of four energy technologies in the hypothetical context of Mexico in 2050, namely: onshore and offshore wind turbines, and open-field and rooftop photovoltaics. A land eligibility analysis incorporating physical, environmental, and socio-political eligibility constraints and individual turbine and photovoltaic park simulations, drawing on 39 years of climate data, is performed for individual sites across the country in an effort to determine the installable potential and the associated levelized costs of electricity. The results reveal that up to 54 PWh of renewable electricity can be produced as a cost of less than 70 EUR/MWh. Around 91% (49 PWh) of this would originate from 23 TW of open-field photovoltaic parks that could occupy up to 578,000 km2 of eligible land across the country. The remaining 9% (4.8 PWh) could be produced by 1.9 TW of onshore wind installations allocated to approximately 68,500 km2 of eligible land that is almost fully adjacent to three mountainous zones. The combination of rooftop photovoltaic and offshore wind turbines account for a very small share of less than 0.03% of the overall techno-economical potential.

Three-dimensional (3D) printing has allowed for production of geometrically complex 3D objects with extreme flexibility, which is currently undergoing rapid expansions in terms of materials, functionalities, as well as areas of application. When attempting to print 3D microstructures in glass, femtosecond laser induced chemical etching (FLICE) – which is a subtractive 3D printing technique – has proved itself a powerful approach. Here, we demonstrate fabrication of macro-scale 3D glass objects of large heights up to ~3.8 cm with an identical lateral and longitudinal spatial resolution of ~20 μm. The remarkable accomplishment is achieved by revealing an unexplored regime in the interaction of ultrafast laser pulses with fused silica which results in aberration-free focusing of the laser pulses deeply inside fused silica.

The doctoral defense, which is an essential requirement for the doctoral degree, is considered to have three dimensions: the scholarly dimension, the emotional (affective) dimension, and the cultural dimension. In this work, I explore the link between sociodemographic factors and students’ perception of the doctoral defense. In particular, I focus on gender, ethnicity, and age at time of defense, as well as current position, and field of study. To address the influence of these aspects on the affective dimension of the doctoral defense, I first reviewed the literature on these socio-demographic aspects as well as the affective dimension of the defense. I then carried out an international survey on doctoral defenses, defense formats, and students’ perceptions and analyzed the 204 completed surveys for this study using quantitative and qualitative methods. The analysis included cross-correlations between students’ perceptions and the studied sociodemographic aspects. The main results of these analyses are that gender affects various aspects of the students’ perception of the doctoral defense and long-term perception, and that female candidates experience more issues with their committee. Ethnicity is important as well, although the participations of non-white respondents in this survey was limited. The influence of age at the defense is limited, and only for the youngest and oldest age groups I observe some differences in perception. There is no relation between current position and perception of the candidates during the defense. Finally, field of study is correlated for various aspects of student perception, committee issues, and long-term perception. The conclusion of this work is that socio-demographic aspects, and in particular gender, ethnicity, and field of study, influence how doctoral candidates experience their defense.

The variation of the cationic composition in I2-II-IV-VI4 semiconductor compounds is an effective tool for altering their properties in a controlled manner. In particular, a partial substitution of Cu for Ag in kesterite Cu2ZnSnS4 was proposed to suppress Cu-Zn antisite defects and the improve photovoltaic performance. However, the efficiency of this approach may substantially depend on the fabrication route. Here, we report on the synthesis of (Cu,Ag)-Zn-Sn-S (CAZTS) and Ag-Zn-Sn-S (AZTS) nanocrystals (NCs) by means of "green" chemistry in aqueous solution and their detailed characterization by Raman spectroscopy and by several complementary techniques. Through a systematic variation of the nominal composition and quantification of the constituent elements in CAZTS and AZTS NCs by XPS, we identified the vibrational Raman and IR fingerprints of both the main AZTS phase and secondary phases of Ag-Zn-S and Ag-Sn-S compounds (for the first time). The formation of the secondary phases of Ag-S and Ag-Zn-S cannot be avoided entirely for this type of synthesis. The Ag-Zn-S phase, having its bandgap in near infrared range, is the reason of the non-monotonous dependence of the absorption edge of CAZTS NCs on the Ag content, with a trend to redshift even below the bandgaps of bulk AZTS and CZTS.

A preliminary study of a wind turbine design is carried out using a wind tunnel to obtain its aerodynamic characteristics. Utilization of data from the study to develop large-scale wind turbines requires further study. This paper aims to discuss the use of wind turbine data obtained from the wind tunnel measurements to estimate the characteristics of wind turbines that have field size. The torque of two small-scale turbines was measured inside the wind tunnel. The first small-scale turbine has a radius of 0.14 m and the second small turbine has a radius of 0.19 m. Torque measurement results from both turbines were analyzed using Buckingham π theorem to obtain a correlation between torsion and diameter variations. The obtained correlation equation is used to estimate the field measurement of turbine power with a radius of 1.2 m. The resulting correlation equation can be used to estimate the power generated by the turbine by the size of the field well in the operating area of the tip speed ratio of the turbine design.

The spatial formation of coherent random laser modes in strongly scattering disordered random media is a central feature in the understanding of the physics of random lasers. We derive a quantum field theoretical method for random lasing in disordered samples of complex amplifying Mie resonators which is able to provide self-consistently and free of any fit parameter the full set of transport characteristics at and above the laser phase transition. The coherence length and the correlation volume respectively is derived as an experimentally measurable scale of the phase transition at the laser threshold. We find that the process of stimulated emission in extended disordered arrangements of active Mie resonators is ultimately connected to time-reversal symmetric multiple scattering in the sense of photonic transport while the diffusion coefficient is finite. A power law is found for the random laser mode diameters in stationary state with increasing pump intensity.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

Abstract: I present a generalization of quantum electrodynamics which includes Diracmagnetic monop oles and the Salam magnetic photon. This quantum electromagnetodynamics has many attractive features. (1) It explains the quantization of electric charge. (2) It describes symmetrized Maxwell equations. (3) It is manifestly covariant. (4) It describes local four-potentials. (5) It avoids the unphysical Dirac string. (6) It predicts a second kind of electromagnetic radiation which can be veried by a tabletop experiment. An eect of this radiation may have been observed by August Kundt in 1885. Furthermore I discuss a generalization of General Relativity which includes Cartan's torsion. I discuss the mathematical denition, concrete description, and physical meaning of Cartan's torsion. I argue that the electric-magnetic duality of quantum electromagnetodynamics is analogous to the spin-mass duality of Einstein-Cartan theory. A quantum version of this theory requires that the torsion tensor corresponds to a spin-3 boson called tordion which is shown to have a rest mass close to the Planck mass. Moreover I present an empirically satised fundamental equation of unied eld theory which includes the fundamental constants of electromagnetism and gravity. I conclude with the remark that the concepts presented here require neither Grand Unication nor supersymmetry.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

Non steady applied magnetic field impact on a liquid metals has good prospects for industry. For a better understanding of heat and mass transfer processes under these circumstances, numerical simulations are needed. A combination of finite elements and volumes methods was used to calculate the flow and solidification of liquid metal under electromagnetic influence. Validation of numerical results was carried out by means of measuring with ultrasound Doppler velocimetry technique, as well as with neutron radiography snapshots of the position and shape of the solid/liquid interface. As a result of the first part of the work, a numerical model of electromagnetic stirring and solidification was developed and validated. This model could be an effective tool for analyzing the electromagnetic stirring during the solidification process. In the second part, the dependences of the velocity pulsation amplitude and the melt velocity maximum value on the magnetic field pulsation frequency are obtained. It was found numerically the ability of the pulsating force action to develop higher values of the liquid metal velocity at a frequency close to the MHD resonance. Obtained characteristics give a more detailed description of the electrically conductive liquid behaviour under action of pulsating traveling magnetic field.

Aim: The main purpose of this feasibility study was to estimate compliance and acceptability rate of a 9-Steps mobile app preparation program. Subsequently, to assess its impact regarding attitudes towards smoking cessation. Methods: The program was only available on versions above iOS 13.3. The ecological study collected user’s data via the app from 04/07/2021 to 28/07/2021. Results: A total of 2331 ecological users completed onboarding; 1926 users (73.9%) completed the step 0 and only 265 users continued in step 1. On average, participants actively engaged with intra-steps activities (85,1%). Most users were highly satisfied at the end of each step. On average 86% found the content of each step comprehensive and relevant. Mann-Whitney tests demonstrated positive changes in attitudes toward smoking cessation on the less confident users: willing (3 to 5, p <.05); confidence (3 to 5, p <.001) and readiness to quit (3 to 5, p <.001). Conclusions: This ecological study corroborates the expected dropout between first use and regular use of health mobile apps. However, engagement and satisfaction rates support the feasibility and acceptability of a 9-step preparation program. Additional research is needed to better understand determinants of regular use of mobile apps and its impact on the target behavior.

This study presents established methods, along with new algorithmic developments, to automate the point cloud processing within the Field Information Modeling (FIM)™ framework. More specifically, given an n-D designed information model, and the point cloud’s spatial uncertainty, the problem of automatic assignment of the point clouds to their corresponding elements within the designed model is considered. The methods addressed two classes of field conditions, namely, (i) negligible construction errors; and (ii) existence of construction errors. The emphasis was given to describing and defining the assumptions in each method and shed light on some of their potentials and limitations in practical settings. Considering the shortcomings of current point cloud processing frameworks, three new and generic algorithms were developed to help solve the point cloud to model assignment in field conditions with both negligible, and existence (or speculation) of construction errors. The effectiveness of the new methods was demonstrated in real-world point clouds, acquired from construction projects, with promising results.

Recent astronomical observations with respect to measurements in distant supernovas, cosmic microwave background and weak gravitational lensing confirm that the Universe is undergoing a phase of accelerated expansion and it has been proposed that this cosmological behavior is caused by a hypothetical dark energy which has a strong negative pressure that allows explain the expanding universe. Several theoretical ideas and models related dark the energy includes the cosmological constant, quintessence, Chaplygin gas, braneworld and tachyonic scalar fields. In this paper, we have obtained new relativistic stellar configurations considering an anisotropic fluid distribution with a charge distribution which could represents a potential model of a dark energy star. In order to investigate the effect of a quadratic equation of state in this anisotropic model we specify particular forms for the gravitational potential that allow solving the Einstein-Maxwell field equations. For these new solutions we checked that the radial pressure, metric coefficients, energy density, anisotropy factor, charge density , mass function are well defined and are regular in the interior of the star. The solutions found can be used in the development of dark energy stars models satisfying all physical acceptability conditions but the causality condition and strong energy condition are violated. We expect that these models have multiple applications in astrophysics and cosmology.

In the electric distribution systems, the “Smart Grid” concept is implemented to encourage energy savings and integration of the innovative technologies, helping the Distribution Network Operators (DNOs) in choosing the investment plans which to lead the optimal operation of the networks and increasing the energy efficiency. In this context, a new phase load balancing algorithm was proposed to be implemented in the low voltage distribution networks with hybrid structures of the consumption points (switchable and non-switchable consumers). It can work in both operation modes (on-line and off-line), uploading information from different databases of the DNO which contain: the consumers’ characteristics, the real loads of the consumers integrated into the Smart Metering System (SMS), and the typical load profiles for the consumers non-integrated in the SMS. The algorithm was tested in a real network, having a hybrid structure of the consumption points, on a time interval by 24 hours. The obtained results were analyzed and compared with other algorithms from the heuristic (Minimum Count of Loads Adjustment algorithm) and the metaheuristic (Particle Swarm Optimization and Genetic Algorithms) categories. The best performances were provided by the proposed algorithm, such that the unbalance coefficient resulted in the smallest value (1.0017). The phase load balancing led to the following technical effects: decreasing the average current in the neutral conductor with 94% and for the energy losses with 61.75 %, and increasing the minimum value of the phase voltage at the farthest pillar with the 7.14 %, compared to the unbalanced case.

Based on the principle of Pancharatnam-Berry phase, we propose an approach to construct dual-functional dielectric metasurface doublets. This type of doublet, which is composed of a substrate and two metasurface layers, performs two different functionalities at two different operating wavelengths. The simulated results of the examples show that the designed dual-functional doublet works well as expected. The proposed approach can be used to design dielectric meta-structures with more layers of meta-surface and thereby with more functionalities, and would be of interest for miniaturization and integration.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

Three-dimensional nanocomposite networks consisting of percolated Si nanowires in a SiO₂ matrix, Si:SiO₂, were studied. The structures were obtained by reactive ion beam sputter deposition of SiO_x (x ≈ 0.6) thin films at 450 °C and subsequent crystallization using conventional oven as well as millisecond line focus laser annealing. Rutherford backscattering spectrometry, Raman spectroscopy, X-ray diffraction, cross-sectional and energy-filtered transmission electron microscopy were applied for sample characterization. While oven annealing resulted in a mean Si wire diameter of 10 nm and a crystallinity of 72 % within the Si volume, almost single-domain Si structures with 30 nm in diameter and almost free of amorphous Si were obtained by millisecond laser application. The structural differences are attributed to the different crystallization processes: Conventional oven tempering proceeds via solid state, millisecond laser application via liquid phase crystallization of Si. The 5 orders of magnitude larger diffusion constant in the liquid phase is responsible for the three times larger Si nanostructure diameter. In conclusion, laser annealing offers not only significantly shorter process times but moreover a superior structural order of nano-Si compared to conventional heating.

The circuitry of the summarized "floating" differential stages (FDS) based on complementary field-effect transistors with a control p-n junction (CJFET), intended for use in low-noise analog microcircuits, for example, operational amplifiers. The results of modeling the flow characteristics of one of the CJFET FDSs in the LTSpice XVII environment at low temperatures (down to -197 ⁰С) and exposure to a neutron flux in the range of 1e13 ÷ 1e15 n / cm² are presented.

The brain rhythms are essential for information processing in neuronal networks. Oscillations recorded in different brain regions can be synchronized and have a constant phase difference, i.e. be coherent. Coherence between local field potential (LFP) signals from different regions in the brain may be correlated with the performance of cognitive tasks, from which it is concluded that these regions of the brain are involved in the task performance together. In this review, we discuss why coherence occurs and how it is coupled to the information transfer between different regions of the hippocampal formation. Coherence in theta and gamma frequency ranges is described since these rhythms are most pronounced during the hippocampus-dependent attention and memory. We review in vivo studies of interactions between different regions of the hippocampal formation in theta and gamma frequency bands. The kay provisions of the review: 1) coherence emerges from synchronous postsynaptic currents in principal neurons, occurring as a result of synchronization of neuronal spike activity; 2) synchronization of neuronal spike patterns in two regions of the hippocampal formation can be realised through induction or resonance; 3) coherence at a specific time point reflects the transfer of information between regions of the hippocampal formation, in particular, gamma coherence reflects the coupling of active neuronal ensembles. Overall, coherence is not an epiphenomenon, but an important physiological process that has certain generation mechanisms and performs important functions in information processing and transmission across the brain regions.

The X-ray induced spin crossover transition of an Fe(II) molecular thin film in the presence and absence of a magnetic field has been investigated. The thermal activation energy barrier in the soft X-ray activation of the spin crossover transition for [Fe{H2B(pz)2}2(bipy)] molecular thin films is reduced in the presence of an applied magnetic field, as measured through X-ray absorption spectroscopy at various temperatures. The influence of a 1.8 T magnetic field is sufficient to cause deviations from the expected exponential spin state transition behavior that is measured in the field free case. We find that orbital moment diminishes with increasing temperature, relative to the spin moment in the vicinity of room temperature.

Recently, ice with the stacking disorder structure, consisting of random sequences of cubic ice (Ic) and hexagonal ice (Ih) layers, is reported to be more stable than pure Ih/Ic. While, due to a much lower free energy barrier of heterogeneous nucleation, in practice, the freezing process of water is usually controlled by heterogeneous nucleation which is triggered by an external medium. Herein, molecular dynamic simulations were carried out to explore the polymorph dependence of ice on the lattice structure of substrates. It turns out that, during the nucleation stage, the polymorph of ice nuclei can be severely altered by the graphene substrate, on which the Ih was found to occupy an absolute majority in new-formed ice. This can be attributed to the structure similarity between graphene and basal face of Ih. Besides the nucleation stage, our results suggest that the substrate can not affect the polymorph of ice which is far from the graphene surface. The polymorph selectivity of graphene to Ih will diminish with the growth of ice layer.

This paper presents a unified reconfigurable coordinate rotation digital computer (CORDIC) processor for floating-point arithmetic. It can be configured to operate in multi-mode to achieve a variety of operations and replaces multiple single-mode CORDIC processors. A reconfigurable pipeline-parallel mixed architecture is proposed to adapt different operations, which maximizes the sharing of common hardware circuit and achieves the area-delay-efficiency. Compared with previous unified floating-point CORDIC processors, the consumption of hardware resources is greatly reduced. As a proof of concept, we apply it to 1638416384 points target Synthetic Aperture Radar (SAR) imaging system, which is implemented on Xilinx XC7VX690T FPGA platform. The maximum relative error of each phase function between hardware and software computation and the corresponding SAR imaging result can meet the accuracy index requirements.

We study the effect of polymer coating, pressure, temperature and light on the electrical characteristics of monolayer WSe₂ back-gated transistors with quasi-ohmic Ni/Au contacts. We prove that the removal of a layer of poly(methyl methacrylate) or a decrease of the pressure change the device conductivity from p to n-type. We demonstrate a gate-tunable Schottky barrier at the contacts and measure a barrier height of ~70 meV in flat-band condition. We report and discuss a temperature-driven change in the mobility and the subthreshold slope which we use to estimate the trap density at the WSe₂/SiO₂ interface. We study the spectral photoresponse of the device, that can be used as a photodetector with a responsivity of ~0.5 AW^-1 at 700 nm wavelength and 0.37 mW/cm² optical power.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

While Spinal Cord Stimulation (SCS) provides satisfaction to almost 2/3 of Persistent Spinal Pain Syndrome-Type 2 (PSPS-T2) patients implanted for refractory chronic back and/or leg pain when not adequately addressed the back pain component, leaves patients in a therapeutic cul-de-sac. Peripheral Nerve field Stimulation (PNfS) has shown interesting results addressing back pain in the same population. Far from placing these two techniques in opposition, we suggest that these approaches could be combined to better treat PSPS-T2 patients. We designed a RCT (CUMPNS), with a 12-month follow-up, to assess the potential added value of PNfS, as a salvage therapy, in PSPS-T2 patients experiencing a “Failed SCS Syndrome” in the back pain component. Fourteen patients were included in this study and randomized into 2 groups (“SCS + PNfS” group/n=6 vs “SCS only” group/n=8). The primary objective of the study was to compare the percentage of back pain surface decrease after 3 months, using a computerized interface to obtain quantitative pain mappings, combined with multi-dimensional SCS outcomes. Back pain surface decreased significantly greater for the ”SCS+PNfS” group (80.2% ± 21.3%) compared to the “SCS only” group (13.2% ± 94.8%) (p=0.012), highlighting the clinical interest of SCS+PNfS, in cases where SCS fails to address back pain.

Geomagnetic induced current (GIC) is a ground end manifestation associated with the space weather perturbations that should be greatly taken into account by the society. Although the GICs implication to the power system is not regular, it can cause large scale of system failure. In equatorial, the power system is considered safe since the most intense of geomagnetic storm happened in high latitude. However, the internal damage due to GICs which finally led to the South African power system failure has totally changed the normal perception. Therefore, a preliminary investigation on the GICs activity in equatorial region is performed to understand the space weather impact to the power system. Time derivative of the horizontal magnetic field component (dB/dt) is done to indicate the GICs activity value based on Faraday’s law. All the reported power failures are compiled to produce the threshold value of dB/dt, which possibly cause the harmful effect to the system. Then, dB/dt analysis is extended to show the pattern of GICs activity in function of magnetic latitude and local time. The results reveal that power network in equatorial region has possibly suffered by GIC. Plus, high number of intense GIC activity in this region occurred during dayside.

Carbon nanotubes are hybridized with metal crystals to impart multifunctionality into the nanohybrids (NHs). Simple but effective synthesis techniques are desired to form both zero-valent and oxides of different metal species on carbon nanotube surfaces. Sol-gel technique brings in significant advantages and is a viable technique for such synthesis. This study probes the efficacy of sol-gel process and aims to identify underlying mechanisms of crystal formation. Standard electron potential (SEP) is used as a guiding parameter to choose the metal species; i.e., highly negative SEP (e.g., Zn) with oxide crystal tendency, highly positive SEP (e.g., Ag) with zero-valent crystal-tendency, and intermediate range SEP (e.g., Cu) to probe the oxidation tendency in crystal formation are chosen. Transmission electron microscopy and X-ray diffraction are used to evaluate the synthesized NHs. Results indicate that SEP can be a reliable guide for the resulting crystalline phase of a certain metal species, particularly when the magnitude of this parameter is relatively high. However, for intermediate range SEP-metals, mix phase crystals can be expected. For example, Cu will form Cu₂O and zero-valent Cu crystals, unless the synthesis is performed in a reducing environment.

In this paper, we present a high-speed, unified elliptic curve cryptography (ECC) processor for arbitrary Weierstrass curves over GF(p), which to the best of our knowledge, outperforms other similar works in terms of execution time. Our approach employs the combination of the schoolbook long and Karatsuba multiplication algorithm for the elliptic curve point multiplication (ECPM) to achieve better parallelization while retaining low complexity. In the hardware implementation, the substantial gain in speed is also contributed by our n-bit pipelined Montgomery Modular Multiplier (pMMM), which is constructed from our n-bit pipelined multiplier-accumulators that utilizes DSP primitives as digit multipliers. Additionally, we also introduce our unified, pipelined modular adder/subtractor (pMAS) for the underlying field arithmetic, and leverage a more efficient yet compact scheduling of the Montgomery ladder algorithm. The implementation on the 7-series FPGA: Virtex-7, Kintex-7, and XC7Z020, yields 0.139, 0.138, and 0.206 ms of execution time, respectively. Furthermore, since our pMMM module is generic for any curve in Weierstrass form, we support multi-curve parameters, resulting in a unified ECC architecture. Lastly, our method also works in constant time, making it suitable for applications requiring high speed and SCA-resistant characteristics.

The early diagnosis of mastitis represents an essential factor for a prompt detection of the animal for further actions. In fact, if not culled, infected cows must be segregated from the milking herd and milked last, or milked with separate milking units. Besides microbiological analysis, the somatic cell count (SCC) commonly used as predictor of intramammary infection, frequently lead to a misclassification of milk samples. To overcome these limitations, more specific biomarkers are continuously evaluated. Total amino acid content increases significantly in mastitic milk compared to normal one. Bovine mastitis can arise as a result of infection of the mammary gland by Staphylococcus aureus. Multiplication of this bacterium within the mammary gland is required for infection to persist. S. aureus requires branched-chain amino acids (BCAAs: isoleucine, leucine, valine) for protein synthesis, branched-chain fatty acids synthesis and environmental adaptation by responding to their availability via transcriptional regulators. The importance of BCAAs for S. aureus physiology necessitates that it either synthesize them or scavenge them from the environment. Increase of BCAAs in composite milk has been postulated to be linked to mammary infection by S. aureus. In the present work, we demonstrated, by a direct ion-pairing reversed-phase method based on the use of the evaporative light-scattering detector (IP-RP-HPLC-ELSD), applied to 65 composite cow milk samples, a correlation between the concentration of isoleucine and leucine and S. aureus load.

The objective of this study was to identify circulating miRNAs affected by disease duration in newly diagnosed children with type 1 diabetes. Forty children and adolescents from The Danish Remission Phase Cohort were followed with blood samples drawn at 1, 3, 6, 12 and 60 months after diagnosis. Pancreatic autoantibodies were measured at each visit. Cytokines were measured only the first year. miRNA expression profiling was performed by RT-qPCR and quantified for 179 human plasma miRNAs. The effect of disease duration was analyzed by mixed models for repeated measurements, adjusted for sex and age. Eight miRNAs (hsa-miR-10b-5p, hsa-miR-17-5p, hsa-miR-30e-5p, hsa-miR-93-5p, hsa-miR-99a-5p, hsa-miR-125b-5p, hsa-miR-423-3p and hsa-miR-497-5p) were found to significantly change expression (adjusted p-value < 0.05) with disease progression. Three pancreatic autoantibodies ICA, IA-2A, GADA65 and 4 cytokines IL-4, IL-10, IL-21, IL-22 were associated with the miRNAs at different time points. Pathway analysis revealed association with various immune-mediated signaling pathways. Eight miRNAs, involved in immunological pathways changed expression levels during the first five years after diagnosis in children with type 1 diabetes, and were associated with variations in cytokine and pancreatic antibodies, suggesting a possible effect on the immunological processes in the early phase of the disease.

A generalization of $\eta$-Ricci solitons is considered involving an additional metric and functions as soliton coefficients. The soliton potential is torse-forming and orthogonal to the contact distribution of the almost contact B-metric manifold. Then such a manifold can also be considered as an almost Einstein-like manifold, a generalization of an $\eta$-Einstein manifold with respect to both B-metrics and functions as coefficients. Necessary and sufficient conditions are found for a number of properties of the curvature tensor and its Ricci tensor of the studied manifolds. Finally, an explicit example of an arbitrary dimension is given and some of the results are illustrated.

Based on a local causal model of the dynamics of curved discrete spacetime, a causal model of quantum field theory in curved discrete spacetime is described. At the elementary level, space(-time) is assumed to consists of interconnected space points. Each space point is connected to a small discrete set of neighbor space points. Density distribution of the space points and the lengths of the space point connections depend on the distance from the gravitational sources. This leads to curved spacetime in accordance with general relativity. Dynamics of spacetime (i.e., the emergence of space and the propagation of space changes) dynamically assigns "in-connections" and "out-connections" to the affected space points. Emergence and propagation of quantum fields (including particles) are mapped to the emergence and propagation of space changes by utilizing identical paths of in/out-connections. Compatibility with standard quantum field theory (QFT) requests the adjustment of the QFT techniques (e.g., Feynman diagrams, Feynman rules, creation/annihilation operators), which typically apply to three in/out connections, to n > 3 in/out connections. In addition, QFT computation in position space has to be adapted to a curved discrete space-time.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

A universally applicable method for the prediction of the isobaric heat capacities of the liquid and solid phase of molecules at 298.15 K is presented, derived from their “true” volume. The molecules’ “true” volume in A³ is calculated on the basis of their geometry-optimized structure and the Van-der-Waals radii of their constituting atoms by means of a fast numerical algorithm. Good linear correlations of the “true” volume of a large number of compounds encompassing all classes and sizes with their experimental liquid and solid heat capacities over a large range have been found, although noticeably distorted by intermolecular hydrogen-bond effects. To take account of these effects, the total amount of 1303 compounds with known experimental liquid heat capacities has been subdivided into three subsets consisting of 1102 hydroxy-group-free compounds, 164 monoalcohols/monoacids, and 36 polyalcohols/polyacids. The standard deviations for Cp(liq,298) were 20.7 J/mol/K for the OH-free compunds, 22.91 J/mol/K for the monoalcohols/monoacids and 16.03 J/mol/K for the polyols/polyacids. Analogously, 797 compounds with known solid heat capacities have been separated into a subset of 555 OH-free compounds, 123 monoalcohols/monoacids and 119 polyols/polyacids. The standard deviations for Cp(sol,298) were calculated to 23.14 J/mol/K for the first, 21.62 J/mol/K for the second, and 19.75 J/mol/K for the last subset. A discussion of structural and intermolecular effects influencing the heat capacities as well as of some special classes, in particular hydrocarbons, ionic liquids, siloxanes and metallocenes, has been given. In addition, the present method has successfully been extended to enable the prediction of the temperature dependence of the solid and liquid heat capacities in the range between 250 and 350 K.

Hydroiodic acid (HI) treated - reduced graphene oxide (rGO) ink/conductive polymeric composites are considered as promising cold cathodes in terms of high geometrical aspect ratio and low field emission (FE) threshold devices. In this study, four simple, cost-effective, solution-processed approaches for rGO-based field effect emitters were developed, optimized and compared; rGO layers were coated on a) n+ doped Si substrate, b) n⁺-Si/P3HT:rGO, c) n⁺-Si/PCDTBT:rGO and d) n⁺-Si/PCDTBT:PC₇₁BM:rGO composites, respectively. The fabricated emitters were optimized by tailoring the concentration ratios of their preparation and field emission characteristics. In a critical composite ratio, FE performance was remarkably improved compared to the pristine Si, as well as n⁺-Si/rGO field emitter. In this context, the impact of various materials, such as polymers, fullerene derivatives, as well as different solvents on rGO function reinforcement and consequently on FE performance upon rGO-based composites preparation was investigated. The field emitter consisted of n⁺-Si/PCDTBT:PC₇₁BM(80%):rGO(20%)/rGO displayed a field enhancement factor of ∼2850, with remarkable stability over 20h and low turn-on field in 0.6V/μm. High-efficiency graphene-based FE devices realization paves the way towards low-cost, large-scale electron sources development. Finally, the contribution of this hierarchical, composite film morphology was evaluated and discussed.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

A novel polyphenol‑coated CoFe₂O₄ system was synthesized as a magnetic adsorbent by chemical oxidative polymerization process for magnetic solid-phase extraction of lawsone. The synthesized nanoadsorbent showed a spherical morphology with diameters under 50 nm by scanning electron microscopy images. The extraction efficiency of this adsorbent was studied towards the extraction of lawsone from saline aqueous solution in dispersion mode. Major parameters including the type and volume of desorption solvent, amount of sorbent, desorption time, extraction time, extraction temperature, ionic strength and pH were optimized. Under the optimum conditions the relative standard deviation in 0.005 µg mL^-1 (inter-day n = 6; intra-day: n = 6; and adsorbent to adsorbent n = 4) were obtained as 5.2, 8.07 and 11.7%, respectively. A linear calibration curve in the range of 0.003–0.5 µg mL^-1 with R² = 0.993 was obtained. The limit of detection and limit of quantification of the method were 0.001 µg mL^-1 and 0.003 µg mL^-1, respectively. The relative recovery percentages were in range of 90-96.4% for henna leaves, henna shampoo, and henna dermal lotion real samples.

ARBTools is a Python library containing a Lekien-Marsden type tricubic spline method for interpolating three-dimensional scalar or vector fields presented as a set of discrete data points on a regular cuboid grid. ARBTools was developed for simulations of magnetic molecular traps, in which the magnitude, gradient and vector components of a magnetic field are required. Numerical integrators for solving particle trajectories are included, but the core interpolator can be used for any scalar or vector field. The only additional system requirements are NumPy.