Differences in the physical and chemical properties of reclaimed water (RW) and natural surface water (SW) lead to the differences in terms of nitrogen and phosphorus release when pipeline sediments enter these water bodies. The nitrogen and phosphorus release kinetics from pipe sediments with different particle sizes have been investigated. The results demonstrated that both SW and RW had a pH buffering effect after sediment addition, and the final pH (approximately 8.1) of RW was lower. The release of total phosphorus (TP) and ammonia nitrogen ( NH₄⁺-N) fitted the first-order kinetic model where the release of TP reached equilibrium; TP release was inhibited in both SW and RW, where RW exhibited the lowest (by a factor of 1.23~2.44) release (0.002 mg/g). The release of NH4+-N was promoted in both SW and RW; the maximum release in RW was 0.0188 mg/g. The amounts of NH₄⁺-N released in SW and RW were 1.02-1.40 and 1.30-1.80 times that of the control group (CG), respectively. The percentage of TP and NH₄⁺-N release in the three groups was highest in 75-154 μm pipe sediment, reaching 34.53% and 43.51% in SW and RW, respectively. These results can assist in the development of water quality evolution models for specific urban scenarios, and provide important guidance for the precise regulation of recharge water quality during and after rainfall.

To provide carbon steel a long corrosion protection effect in NaCl solution with various pH, a pH-controlled intelligent inhibitor based on poly-acrylamide (PAM) and oleate imidazoline (OIM) was synthesized. SEM, FT-IR and TGA results indicating the OIM inhibitor was successfully loaded into PAM hydrogel with a very high content (39.64 wt%). The OIM release behavior from hydrogel structure have two stages, quickly release and sustained release. The pH of solution could affect the initial release kinetics of OIM inhibitor and the diffusion path in hydrogel structure. Weight loss measurement of L80 steel in different pH solution with OIM@PAM proved the inhibitor responsive release mechanism and an-ti-corrosion performance. The inhibition efficiency of OIM@PAM can maintain over 80% after long term immersion in harsh corrosive environment (pH 3), which is much higher than the inhibition efficiency of inhibitor in moderate corrosive solution.

Lipid mesophases are being intensively studied as potential candidates for drug-delivery purposes. Extensive experimental characterization has unveiled a wide palette of release features depending on the nature of the host lipids and of the guest molecule, as well as on the environmental conditions. However, only few simulation works have addressed the matter, which hampers a solid rationalization of the richness of outcomes observed in experiments. Particularly, to date there are no theoretical works addressing the impact of hydropathy on the transport of a molecule within lipid mesophases, despite the significant fraction of hydrophobic molecules among currently-available drugs. Similarly, the high heterogeneity of water mobility in the nanoscopic channels within lipid mesophases has also been neglected. To fill this gap, we introduce here a minimal model to account for these features in a lamellar geometry, and systematically study the role played by hydropathy and water-mobility heterogeneity by Brownian-dynamics simulations. We unveil a fine interplay between the presence of free-energy barriers, the affinity of the drug for the lipids, and the reduced mobility of water in determining the net molecular transport. More in general, our work is an instance of how multiscale simulations can be fruitfully employed to assist experiments in release systems based on lipid mesophases.

Surface modification of polypropylene (PP) films is achieved using gamma-irradiation-induced grafting to proffer with antimicrobial activity. The copolymer was obtained through a versatile two-step route; pristine PP is exposed to gamma rays and grafted using methyl methacrylate (MMA), then N-vinylimidazole (NVI) is grafted onto the copolymer PP-g-MMA by simultaneous irradiation. The characterization included Fourier-Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscope (SEM), Thermogravimetric Analysis (TGA), X-ray Photoelectron Spectroscopy (XPS), and physicochemical analysis of swelling and contact angle. The copolymer (PP-g-MMA)-g-NVI was loaded with vancomycin, and the drug released was quantified by UV-vis spectrophotometry at different pH. The surface of (PP-g-MMA)-g-NVI exhibited pH-responsiveness and moderate hydrophilicity, suitable properties for controlled drug release.

In this study, a slow-release urea fertilizer hydrogel was synthesized from hydroxyl propyl methyl cellulose, polyvinyl alcohol and glycerol blends with paper (blended paper) as second layer. The fertilizer hydrogel was characterized by SEM, XRD and FTIR. Its retention in sandy soil, swelling behavior in distilled and tap water as well as slow-release behavior to urea were investigated. The results indicated that the fertilizer had good slow-release properties and ability to retain water in soil. However, the addition of blended paper as a second layer matrix was found to help improve the release properties of the fertilizer. The swelling kinetic of the hydrogel followed the Schott’s Second order model. The release kinetics of urea in water was best described by the Zero order model signifying that the release behavior was independent of fertilizer concentration

Background: Spine shape parameters, such as leg length, kyphotic or lordotic angle, are influenced by low back pain. There is also evidence that the thoracolumbar fascia plays a role in such pa-thologies. This study examined the immediate effects of a myofascial release technique (MFR) on the thoracolumbar fascia and of an osteopathic treatment (OMT) on postural parameters in pa-tients with acute low back pain (aLBP). Methods: This study was a single-blind randomized pla-cebo-controlled trial. Seventy-one subjects (43.8 ± 10.5 years) suffering from aLBP were randomly and blinded assigned to three groups to be treated with MFR, OMT or a placebo intervention. Spinal shape parameters (functional leg length discrepancy (fLLD), kyphotic angle, lordotic an-gle) were measured before and after the intervention using video raster stereography. Results: Within the MFR group, fLLD reduced by 5.2 mm, p < 0.001 and kyphotic angle by 8.2 degrees, p < 0.001. Within the OMT group, fLLD reduced by 4.5 mm, p < 0.001 and kyphotic angle by 8.4 °, p = 0.007. Conclusion: MFR and OMT have an influence on fLLD and the kyphotic angle in aLBP patients. The interventions could have a regulating effect on the impaired neuromotor control of the lumbar muscles.

The activity of prioritizing software requirements should be done as efficiently as possible. Selecting the most stable requirements for the most important customers for the development company can be a positive factor when we consider that the available resource does not always encompass the implementation of all requirements. Quantitative methods for reaching software prioritization in releases are many in the field of Search-Based Software Engineering (SBSE). However, we show that it is possible to use qualitative Verbal Decision Analysis (VDA) methods to solve this same type of problem. Moreover, we will use the ZAPROS III-i methods to prioritize requirements considering the opinion of the decision-maker, who will participate in this process. Finally, the results obtained in the VDA structured methods were quite satisfactory when compared to the methods using SBSE. A comparison of results between quantitative and qualitative methods will be made and discussed later.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Polyhydroxyalkanotes (PHA) are bio-based microbial biopolyesters with stiffness, elasticity, crystallinity and degradability tunable by the monomeric composition, bio-production strategy and post-synthetic processing; they display biological alternatives for diverse technomers of petrochemical origin. This, together with the fact that their monomeric and oligomeric in vivo degradation products do not exert any toxic or elsewhere negative effect to living cells or tissue of humans or animals, makes them highly stimulating for various applications in the medical field. The article provides an overview of PHA application in the therapeutic, surgical and tissue engineering area, and reviews strategies to produce PHA at purity levels high enough to be used in vivo. Tested applications of differently composed PHA and advanced follow-up products as carrier materials for controlled in vivo release of anti-cancer drugs or antibiotics, as scaffolds for tissue engineering, as guidance conduits for nerve repair or as enhanced sutures, implants or meshes are discussed from both a biotechnological and a material-scientific perspective. Particular attention is devoted to the adaptation of traditional polymer processing techniques for production of medicine-related devices based on PHA, such as melt-spinning, melt extrusion, or solvent evaporation, and to emerging processing techniques like 3D-printing, computer-aided wet-spinning, laser perforation, or electrospinning.

This study was aimed to assess visual performance and overall satisfaction of extended depth of focus (EDOF) contact lenses (CLs) in a presbyopic population. We prospectively investigated visual acuity at all distances (0.3, 0.4, 0.5, 0.7, 1, and 5 m), higher-order aberrations (HOAs), contrast sensitivity function, and, overall satisfaction score, before and during EDOF CL wear. Binocular visual acuity at 0.3, 0.5, 0.7, 1, 2, 3, and 5 m when wearing EDOF CLs was 0.01 ± 0.14, -0.08 ± 0.02, -0.08 ± 0.02, -0.08 ± 0.00, -0.08 ± 0.00, -0.08 ± 0.02, and -0.07 ± 0.02, respectively. We found a significant improvement at near to intermediate distances (0.3, and 0.5 m), but no significant change at intermediate to far distances (0.7, 1, 2, 3, and 5 m) between before and during CL wear. The area under the log contrast sensitivity function was not significantly changed neither under photopic nor mesopic conditions (p=0.099, and p=0.689). Ocular third-order aberrations, fourth-order aberrations or total HOAs for a 4-mm pupil significantly increased. The overall satisfaction score significantly improved by wearing EDOF CLs. EDOF CLs significantly improved visual acuity at near to intermediate dis-tances, while maintaining far vision, and the effect of contrast sensitivity was minimal, suggesting its viability of presbyopic correction in such candidates.

(1) Background: Ulcerative colitis (UC) is characterized by immune system dysregulation with frequent extraintestinal manifestations, including airways involvement. Reduction in CO diffusing capacity and functional alterations in small airways have been described. The extended analysis of Fractional Exhaled Nitric Oxide (FeNO), may distinguish the sites of production and the presence of small airways inflammation being a useful, non-invasive marker for these patient’s follow up. The aim of our study was to compare PFTs, FeNO and CANO values of UC patients with different clinical disease activity and healthy subjects to reveal lung function abnormalities and the presence of subclinical airway inflammation. (2) Methods: We enrolled 42 adult outpatients with different clinical activity stages of UC (mean age 39±13 years) and a healthy control group of 41 subjects (mean age 29±3 years). C-reactive protein (CRP) and FeNO values at different flows (50,100 and 200 ml/sec) were collected. All patients performed pulmonary function tests (PFT’s) with static volumes and diffusing capacity (DLCO). (3) Results: FENO, CANO and CRP values were significantly increased in UC patients when compared with controls (p=0.02 and p&lt;0.0001, respectively) and proportionally to the disease activity (FeNO class 3: 27.1 ppb vs class 1-2: 6.2 ppb; CANO values class 3: 8.1 ppb vs class 1-2: 2.0 ppb (p &lt; 0.0001). TLC and DLCO were significantly reduced in UC patients compared to controls (p=0.011 and p&lt;0.0001, respectively). (4) The results of this study show significant lung functional abnormalities in UC patients and suggest the presence of airway inflammation directly correlated with the disease activity suggesting an integrated approach in routine assessment.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

This review aimed at defining and classifying extended spectrum β-lactamases, ESBLs and carbapenemases, summarizing the different phenotypic methods used to detect production of these enzymes in clinically significant gram negative bacteria and also describing the methods that discourse challenges mostly encountered during detection of these enzymes in microbiology laboratories with the purpose of formulating recommendations on best practice to screen for these enzymes. We conclude that the modified double disk synergy, MDDS is not only suitable for the confirmation of ESBL production after screening isolates with the cephalosporin/clavulanate combination disc diffusion or broth micro-dilution methods but also distinguishes ESBL production and over-expression of AmpC-derepressed mutants and as well serves as an indicator for AmpC screening. Furthermore, we suggest cefotaxime, ceftazidime and cefpodoxime (for testing using a single drug) as indicator antibiotics of choice for ESBL detection. The MDDS and cefoxitin/AmpC inhibitor combination disc method, using cloxacillin and phenylboronic acid can be used as screening tests for AmpC production and either the AmpC disc test, the disc approximation test or the modified three dimensional extract test as confirmatory tests for AmpC production. We also suggest that confirmation of carbapenemase production be done with the modified hodge test, using Klebsiella pneumoniae ATCC 700603 as the indicator organism or the modified carbapenem inactivation method. However, to differentiate between the different classes of carbapenemases, boronic acid and EDTA based methods (double-disk synergy tests and combined-disk tests) using imipenem, meropenem and ertapenem, in combination with 3-aminophenylboronic acid and ethylene diamine tetra acetic acid be used.

β3-Adrenoceptors mediate several functions in rodents that could be beneficial for the treatment of obesity and type 2 diabetes. This includes promotion of insulin release from the pancreas, of cellular glucose uptake, of lipolysis, and of thermogenesis in brown adipose tissue. In combination, they lead to a reduction of body weight in several rodent models including ob/ob mice and Zucker diabetic fatty rats. These findings stimulated drug development programs in various pharmaceutical companies, and at least nine β3-adrenoceptor agonists have been tested in clinical trials. However, all of these projects were discontinued due to lack of clinically relevant changes of body weight. Following a concise historical account of discoveries leading to such drug development programs we discuss species differences that explain why β3-adrenoceptors are not a meaningful drug target for the treatment of obesity and type 2 diabetes in humans.

Pathophysiology of depression is related with reduced volume of the hippocampus and amygdala and hypertrophy of the nucleus accumbens. The mechanism of these changes is not well under-stood, but clinical studies have shown that administration of the fast-acting antidepressant keta-mine reversed the decrease in hippocampus and amygdala volume in depressed patients, and the magnitude of this effect correlated with the reduction of depressive symptoms. In the present study, we attempted to find out whether the psychedelic substance psilocybin affects neurotransmission in the limbic system in comparison to ketamine. Psilocybin and ketamine increased the release of dopamine (DA) and serotonin (5-HT) in the nucleus accumbens of naive rats as demonstrated using microdialysis. Both drugs influenced glutamate and GABA release in the nucleus accumbens, hippocampus and amygdala and increased ACh levels in the hippocampus. The changes in D2, 5-HT1A and 5-HT2A receptor density in the nucleus accumbens and hippocampus was observed as a long-lasting effect. A marked anxiolytic effect of psilocybin in acute phase and 24 h post-treatment was shown in the open field test. These data provide the neurobiological background for psilocybin effect on stress, anxiety and structural changes in the limbic system and translate into antidepres-sant effect of psilocybin in depressed patients.

In the land use planning framework in the neighbourhood of industrial facilities, the current approach to predicting the consequences of massive toxic gas releases is generally based on Gaussian or integral models. For many years, CFD models have been more and more used in this context, in accordance with the development of High-Performance Computing (HPC). The present paper focuses on harmonizing input data for Atmospheric Transport and Dispersion (AT&amp;D) modelling between the widely used approaches. First, a synthesis of the practice’s harmonization for atmospheric dispersion modelling within the framework of risk assessment is presented. Then, these practices are applied to a large-scale INERIS ammonia experimental release. For illustration purposes, the impact of the proposed harmonization will be evaluated using different approaches: the SLAB model, the FDS model and the Code_Saturne model. The two main focuses of this paper are the adaptation of the source term dealing with a massive release and the wind flow modelling performance using an experimental signal for CFD models inflow. Finally, comparisons between the modelling and experimental results enable checking the consistency of these approaches and reinforce the importance of the input data harmonization for each AT&amp;D modelling approach.

Our knowledge of biology and mast cell (MC) function, as well as disorders associated with the pathologic activation of MCs has been evolving over the last few decades. Anaphylaxis, mast cell activation syndrome (MCAS) and mastocytosis are interrelated yet distinct conditions within the spectrum of mast cell activation disorders. Nevertheless, all three conditions can co-exist in one and same patient, as pathologic MC activation is the key finding in all three. When mediator release is excessive and involves multiple systems, anaphylaxis and MCAS may occur. Furthermore, mastocytosis is a clonal disorder of MCs and often presents with anaphylaxis and MCAS. Nevertheless, in some cases even proliferative and accumulative features of MCs in mastocytosis can account for symptoms and disease progression. In each case, diagnosis can be only made when diagnostic consensus criteria are fulfilled. The current article aims to provide a concise clinical update and pinpoint main difficulties in diagnosing these puzzling disorders of MCs in medical practice.

Heat requirements play an important role in plant flowering, and control the flowering period of woody ornamental plants to a certain extent. In this study, the perennial potted seedlings of four typical Prunus mume cultivars 'Xiaolve', 'Baixuzhusha', 'Fenghou' and 'Danfenghou' were used as materials. The way of regulating the cultivation temperature is adopted to achieve the purpose of relieving the natural dormancy and forcing the blooming of P. mume. Its content includes the research on the heat requirements of P. mume cultivars widely planted in Beijing, and the analysis of the influence of different facility cultivation temperatures on the flowering characteristics of P. mume, providing a theoretical basis for further exploring the cultivation techniques of P. mume bonsai flowering regulation. The results showed that, according to the Growing degree-hour model, the HR of 'Xiaolve', 'Baixuzhusha', 'Fenghou' and 'Danfenghou' flower buds were 3583.70 GDH℃, 3217.30 GDH ℃, 3996.50 GDH ℃, 4732.20 GDH ℃, respectively. According to the effective accumulated temperature model, the HRs of above cultivars were 350.65 ℃, 319.30 ℃, 510.30 ℃, 558.50 ℃, respectively. In addition, the temperature of different cultivation facilities did not significantly change the flowering quality such as flower diameter and fragrance. Temperature also affects the growth and development speed, affecting the flowering time. Under the facility environment with higher temperatures, the flowering process is faster and the flowering period is shorter.

Zero-rate output (ZRO) drift induces deteriorated micro-electromechanical system (MEMS) gy-roscope performances, severely limiting its practical applications. Hence, it is vital to explore an effective method toward ZRO drift reduction. In this work, we conduct an elaborate investigation on the impacts of the internal and packaging stresses on the ZRO drift at the thermal start-up stage, and propose a temperature-induced stress release method to reduce the duration and magnitude of ZRO drift. Self-developed high-Q dual mass tuning fork gyroscopes (TFGs) are adopted to study the correlations between temperature, frequency and ZRO drift. Furthermore, a rigorous finite element simulation model is built based on the actual device and packaging structure, revealing the temperature and stresses distribution inside TFGs. Meanwhile, the relationship between temperature and stresses are deeply explored. Moreover, we introduce a temperature-induced stress release process to generate thermal stresses and reduce the temperature-related device sensitivity. By this way, the ZRO drift duration is drastically reduced from ~2000 s to ~890 s, and the drift magnitude decreases from ~0.4 °/s to ~0.23 °/s. This stress release method achieves a small bias instability (BI) of 7.903 °/h and a low angle random walk (ARW) of 0.792 °/√h, and the long-term bias performance is significantly improved.

Breast cancer is the most widespread malignancy in women from corner to corner of the world. Nanostructured lipid carrier (NLC) proved its efficacy in the treatment of cancer. NLC loaded with Imatinib (IMA) (NANIMA) was prepared and evaluated for in vitro efficacy in MCF-7 breast cancer cells. Hot homogenization method was used for the preparation of NANIMAs. Aqueous solution of surfactants (hot) was mixed with molten mixture of stearic acid and sesame oil (hot) under homogenization. The prepared NANIMAs were characterized and evaluated for size, polydispersity index, zeta potential, encapsulation efficiency, release studies, stability studies and MTT assay (cytotoxicity studies). The optimized NANIMA revealed particle size of 104.63 ± 9.55 d.nm, PdI of 0.227 ± 0.06 and EE of 99.79 ± 0.03. All NANIMAs revealed slow and sustained release behaviour. The surfactants used in the preparation of NANIMAs exhibited their effects on particle size, zeta potential, encapsulation efficiency, stability studies and release studies. The cytotoxicity studies unveiled 8.75 times increase in cytotoxicity for optimized NANIMA (IC50 = 6 µM) when compared with IMA alone (IC50 = 52.5 µM) on MCF-7 breast cancer cells. After this, NLC containing IMA possibly will be employed for the cure of breast cancer. A lesser amount of IMA loaded NLC will be sufficient than IMA alone for the treatment of breast cancer. Moreover, the patient will exhibit not as much of adverse effects as in case of IMA alone. Consequently, NANIMA could prove to be useful for effective therapeutic outcome in breast cancer treatment.

The motivation of this work is to investigate experimentally the influence of non-thermal plasma (NTP) application on the reaction kinetics of atmospheric pressure steam gasification of charcoal using a thermostatically controlled drop tube reactor. A gliding-arc generator provides about 1 kW electrical power NTP. For comparison thermal gasification is investigated under comparable flow and specific energy input conditions providing additional heat to the steam. Optical temperature measurement 20 cm flow down of the NTP zone is utilized to characterize the specific enthalpy of the reactive flow. The composition of produced syngas is measured by a gas analyzer and used for the calculation of gas flow rates. The results show a NTP-enhancement on the production of individual syngas components (H2, CO, CH4), especially on hydrogen production by around 39%. The syngas-based carbon conversion and hydrogen release are calculated from the carbon and hydrogen balance between the correspondent content in syngas and in the feedstock. The NTP promoted the carbon conversion and hydrogen release by 25% and 31%, respectively. The first-order reaction kinetics are determined by data-fitting in an Arrhenius diagram. The plasma enhanced the reaction rate coefficients by 27%. Based on experimental results and other literature, possible plasma-induced reactions are proposed.

Mere similar grades of same excipients manufactured by two different manufacturers often differ significantly that they even have an impact on the variations in final product or dosage form. Solid lipids are one of the most available options as matrix former in sustained drug delivery. Due to their chemical and physical complexity, lipids may exhibit a complex behaviour (i.e. melting crystallization and polymorphism). The aim of this study was to evaluate the physical and chemical properties of two Glyceryl Monostearate (GMS) lipids (Geleol from Gattefosse and Capmul GMS 50K from Abitec Corp. USA) and how these properties may affect during melt granulation process for sustained release applications. Thermal processing was applied on GMS samples to understand the polymorphic nature and suitability as meltable binders. Niacin was used as model drug. A thorough evaluation of GMS samples and sustained release tablets was undertaken using analytical techniques such as differential scanning calorimetry (DSC), X-ray diffraction (XRD). Moreover, melt viscosity study assisted to apprehend the behaviour of GMS samples in hot melt extrusion processing. Surface morphology of the drug and extruded granules examined via SEM and AFM revealed high level of surface interaction and dense structure of drug inside lipid matrix. The DSC and XRD study confirmed that Geleol could not withstand the heat treatment applied during thecontinuous melt granulation processing. The shifting of stable β form to an unstable α form in Geleol was detected. In the contrary case, Capmul GMS 50K was able to withstand the heat treatment supported by the applied analytical techniques. Nonetheless,both GMS samples perform differently in final dosage form. This change in stable β form to an unstable α form affected dissolution profiles at 3 months storage in accelerated condition. This study helped to interpret the complex solid-state behaviour of solid lipid extrudates with different compositions, in order to the simply and outline a suitable formulation strategy for the development of lipid-based oral dosage forms.

This study leverages the relationships between the Great Plains low-level jet (GP-LLJ) and the circumglobal teleconnection (CGT) to enhance the 30-day rainfall forecast skill in the Northern Great Plains (NGP). The assessment of 30-day simulated precipitation using the Climate Forecast System (CFS) is contrasted with the North American Regional Reanalysis, searching for sources of precipitation predictability associated with extended wet and drought events. We analyze the 30-day sources of precipitation predictability using (1) the characterization of dominant statistical modes of variability of 900-mb winds associated with the GP-LLJ, (2) the large-scale atmospheric patterns based on 200-mb geopotential height (HGT), and (3) the use of GP-LLJ and CGT conditional probability distributions using a continuous correlation threshold approach to identify when and where the forecast of NGP precipitation occurs. Two factors contributing to the predictability of precipitation in the NGP are documented. We found that multi-scale geospatial interactions occur at the daily and sub-seasonal time windows. The CFS reforecast suggests that the ability to forecast sub-seasonal precipitation increases in response to the enhanced simulation of the GP-LLJ and CGT. Finally, the multi-dimensional analysis of covariance reveals that high-precipitation forecasting skill is associated with a better prognostic of GP-LLJ and CGT.

Taiwan is highly susceptible to global warming, experiencing a 1.4°C increase in air temperatures from 1911-2005, which is twice the average for the Northern Hemisphere. This has led to higher rates of respiratory and cardiovascular mortality. Accurately predicting maximum temperatures during the summer season is crucial, but numerical weather models become less accurate and more uncertain beyond five days. To improve forecast reliability, statistical post-processing is needed to address systematic errors. In September 2020, NOAA NCEP implemented the Global Ensemble Forecast System version 12 (GEFSv12) to help manage climate risks. This study developed a Hybrid statistical post-processing method that combines Artificial Neural Networks (ANN) and Quantile mapping (QQ) approaches to predict daily maximum temperatures and extremes in Taiwan during the summer season. The Hybrid technique, utilizing deep learning techniques, was applied to the GEFSv12 reforecast data and evaluated against ERA5 reanalysis. The Hybrid technique was the most effective among the three techniques tested. It had the lowest bias, RMSE, and highest correlation coefficient. It successfully reduced the warm bias and overestimation of Tmax extreme days. This led to improved prediction skills for all forecast lead times. Compared to ANN and QQ, the Hybrid method was more effective in predicting summer daily Tmax and its extremes on an extended-range time scale deterministic and ensemble probabilistic forecasts over Taiwan.

The selectin of a demand forecasting method is critical for companies aiming to avoid manufacturing overproduction or shortages in pursuit of sustainable development. Various qualitative and quantitative criteria with different weights must be considered during the evaluation of a forecasting method. The qualitative criteria and criteria weights are usually assessed in linguistic terms. Aggregating these various criteria and linguistic weights for evaluating and selecting demand forecasting methods in sustainable manufacturing is a major challenge. This paper proposes an extension of fuzzy Elimination and Choice Translating Reality (ELECTRE) I to resolve this problem. In the proposed method, fuzzy weighted ratings are defuzzified with the signed distance to develop a crisp ELECTRE I model. Moreover, an extension to ELECTRE I is developed by suggesting an extended modified discordance matrix and a closeness coefficient for ranking alternatives. The proposed extension can overcome the problem of information loss which can lead to incorrect ranking result when using the Hadamard product to combine concordance and modified discordance matrices. A comparison is conducted to show the advantage of the proposed extension. Finally, a numerical example is used to demonstrate the feasibility of the proposed method; furthermore, a numerical comparison is made to display the advantage of the proposed method.

Background: The cavernous sinus (CS) is a highly vulnerable anatomical space, mainly for the neurovascular structures which it contains, therefore a detailed knowledge of its anatomy is mandatory for the surgical unlocking. To compare the anatomy of this region from different endoscopic and microsurgical operative corridors, also focusing on the corresponding anatomic landmarks met along these routes. Furthermore, we tried to define the safe entry zones to this venous space from these three different operative corridors and provide indications regarding the optimal approach according to the lesion location. Methods: Five embalmed and injected adult cadaveric specimens (10 sides) separately underwent dissection and exposure of the CS via superior eyelid endoscopic transorbital (SETOA), extended endoscopic endonasal transsphenoidal-transethmoidal (EEEA) and microsurgical transcranial fronto-temporo-orbito-zygomatic (FTOZ) approaches. The anatomical landmarks and the content of this venous space have been described and compared from these surgical perspectives. Results: The SETOA allowed the exposure of the entire lateral wall of the CS without entering its neurovascular structures and part of the posterior wall; furthermore, thanks to its anteroposterior trajectory, it allowed to disclose in a minimally invasive fashion, also the posterior ascending segment of the cavernous ICA with the related sympathetic plexus through the Mullan’s triangle. Through the anterolateral triangle, the transorbital corridor allowed to expose the lateral 180 degrees of vidian nerve and artery in the homonymous canal, the anterolateral aspect of the lacerum segment of the ICA, at its the transition zone from the petrous horizontal to the ascending posterior cavernous segment, surrounded by the carotid sympathetic plexus, and the medial Meckel’s cave. Conclusion: Different regions of the cavernous sinus are better exposed by different surgical corridors. The relationship of tumor and cranial nerves in the lateral wall guides the selection of the approach to cavernous sinus lesions. The transorbital endoscopic approach can be considered a safe and minimally invasive complementary surgical corridor to the well-established transcranial and endoscopic endonasal routes in the exposure of the cavernous sinus. Nevertheless, peer knowledge of the anatomy and a surgical learning curve are required.

Background and objective: Acinetobacter baumannii (A. baumannii) is an important nosocomial pathogen that possesses not only intrinsic resistance to many classes of antibiotics, but also is capable to rapidly develop antimicrobial resistance during treatment. The aim of our study was to determine the production of different types of β-lactamases (AmpC, ESBL, KPC) in A. baumannii strains, to evaluate its association with antimicrobial resistance, and to identify the changes in these characteristics after 5 years. Materials and methods: A total of 233 A. baumannii strains were isolated from different clinical specimens of patients treated at the Hospital of Lithuanian University of Health Sciences in 2016–2017 and 2021–2022. All clinical cultures positive for A. baumannii were analyzed. The type of β-lactamase was detected by phenotypic methods using ESBL plus AmpC screen disk tests and the combination meropenem disk test. Results: In 2016–2017 and 2021–2022, all A. baumannii strains were resistant to ciprofloxacin; more than 80% were resistant to carbapenems, piperacillin/tazobactam, gentamicin, and tobramycin. Comparison of two different period showed that the production of two different types of β-lactamases increased more than 5-fold (from 17.7% to 94.2%, p < 0.001), and the production of all three types of β-lactamases, more than 4-fold (from 1.3% to 5.8%, p < 0.001). A. baumannii strains producing two or three types of β-lactamases were more often resistant to tigecycline, tetracycline, and doxycycline than strains producing one type of β-lactamases (p < 0.001). Conclusions: The frequency of isolation of A. baumannii strains producing two or three β-lactamases types and the resistance rates to ampicillin/sulbactam, tigecycline, tetracycline, and doxycycline increased in 2020–2021 as compared with 2016–2017. The production of two or three types of β-lactamases by A. baumannii strains was associated with higher resistance rates to tetracyclines.

This research work presents the nonlinear control framework to estimate and reject the mismatched lumped disturbances acting on the nonlinear uncertain system. It is an unfortunate fact that the conventional Extended State Observer (ESO) is not capable to estimate the mismatched lumped disturbance and its derivative simultaneously for the systems. Also, the basic ESO is only suitable for systems with Integral Chain Form (ICF) structure. Similarly, the conventional Feedback Linearizing Control (FLC) approach is not robust for stabilizing the systems in the presence of disturbances and uncertainties. Hence, the nonlinear control framework is proposed to overcome the above issues which are composed of, (a) Dual Extended State Observer (DESO), and (b) DESO based FLC. The DESO provides information on the unmeasured state, mismatched disturbance, and its derivative. While the DESO-FLC utilizes the information from DESO to counter the effect of such disturbances and to stabilize the nonlinear systems around the reference point. The detailed closed-loop analysis is presented for the proposed control framework in the presence of lumped disturbances. The performance robustness of the presented design has been validated for the third order, nonlinear, unstable, and disturbed Magnetic Levitation System (MLS). The results of the DESO-FLC approach are compared with the most popular Linear Quadratic Regulator (LQR) and nonlinear FLC approaches based on the integral error criterion and the average electrical energy consumption.

Purpose: To evaluate clinical outcomes after bilateral mix-and-match cataract surgery using extended depth of focus (EDOF) and diffractive multifocal (DMF) intraocular lenses (IOLs). Methods: Thirty-seven patients received Tecnis Symfony EDOF IOL (ZXR00) implantation in the dominant eye, and Tecnis +3.25 DMF IOL (ZLB00) in the non-dominant eye. Patients were followed for 3 months, and uncorrected and corrected distance visual acuity (UDVA, CDVA) , uncorrected intermediate and near visual acuity (UIVA, UNVA), contrast sensitivity, defocus curves, stereopsis, and patient satisfaction were assessed. Results: At 3 months, mean logMAR UDVA was 0.07 ± 0.09 in EDOF IOL eyes, 0.12 ± 0.11 in DMF IOL eyes, and 0.02 ± 0.05 in both eyes. UIVA was 0.11 ± 0.11 in EDOF IOL eyes, 0.16 ± 0.12 in DMF IOL eyes, and 0.04 ± 0.07 in both eyes. UNVA was 0.25 ± 0.15 in EDOF IOL eyes, 0.22 ± 0.16 in DMF IOL eyes, and 0.13 ± 0.13 in both eyes. Thirty patients(81.1%) were more than satisfied with near vision, and 8 patients(21.6%) complained of severe glare and halo. Spectacle independence for near vision was achieved in 34 patients(91.9%), and 31 patients(83.8%) had better than a 50 second arc of stereopsis. Conclusion: Mix-and-match cataract surgery with EDOF and DMF IOL implantation provided good visual outcomes through all distances. Also excellent patient satisfaction was achieved with high level of spectacle independence and minimal photic phenomena.

We apply utilized the extended form of the auxiliary equation method to obtain extensively reliable exact travelling wave solutions of perturbed Gerdjikov–Ivanov equation (GIE) that is widely used as a model in the field theory of quanta and non-linear optics. The method is based on a simple first order second degree ODE. The new form of the approach gives more solutions to the governing equation efficiently.

This paper focuses on the integrated guidance and autopilot design with control input saturation in the end-game phase of hypersonic flight. Firstly, uncertain nonlinear integrated guidance and autopilot model is developed with third actuator dynamics, where the control surface deflection has magnitude constraint. Secondly, neural network is implemented in extended state observer (ESO) design, which is used to estimate the complex model uncertainty, nonlinearity and state coupling. Thirdly, a command filtered back-stepping controller is designed with hybrid sliding surfaces to improve the terminal performance. In the process, different command filters are implemented to avoid the influences of disturbances and repetitive derivation, meanwhile solve the problem of unknown control direction caused by saturation. The stability of closed-loop system is proved by Lyapunov theory, and the principles abided by the controller parameters are concluded through the proof. Finally, series of 6-DOF numerical simulations are presented to show the feasibility and validity of the proposed controller.

In South Western Indian ocean (IO), Extended-Spectrum β-Lactamase producing Enterobacteriaceae (ESBL) are a main public health issue. In livestock, ESBL burden was unknown. The aim of this study was estimating the prevalence of ESBL on commercial farms in Reunion, Mayotte and Madagascar and genes involved. Secondly, risk factors of ESBL occurrence in broiler, beef cattle and pig farms were explored. In 2016-2017, commercial farms were sampled using boot swabs and samples stored at 4°C before microbiological analysis for phenotypical ESBL and gene characterization. A semi-directive questionnaire was performed. Prevalences observed in all production types and territories were elevated, except for beef cattle in Reunion which differed significantly. The most common ESBL gene was the CTX-M-1 subtype. Generalized linear models explaining ESBL occurrence varied between livestock production sectors and allowed identifying main protective (e.g., water quality control and detergent use for cleaning) and risk factors (e.g., recent antibiotic use, other farmers visiting the exploitation, pet presence). This study is the first to explore tools for antibiotic resistance management in IO farms. It provides interesting hypothesis to explore about antibiotic use in IO and ESBL transmission between pig, beef cattle and humans in Madagascar.

The use of natural raw substances for food preservation could provide a great contribution to food waste reducing, circular economy enhancing, and green processes application widening. Recent studies indicated that natural preservatives release kinetics significantly influenced the food preservation process. The use of porous materials as absorber for natural essential oils provided nanohybrids with excellent antioxidant and antimicrobial properties. In this study the well-known SBA-15 porous material was used to control the release of the natural preservative thyme oil on food surface and to extend the food shelf-life. Results indicated that the thyme oil loading was higher than other porous materials reported recently and the addition of SBA-15 to the LDPE increases the water/oxygen barrier. The film with the higher thyme-oil@SBA-15 nanohybrid content exhibited the slower release kinetic. The antioxidant activity of the final films ignited after 48 hours, was in the range of 60-70%, and was almost constant for 7 days. Finally, all tests indicated a sufficient improvement by the addition of thyme-oil@SBA-15 nanohybrids in the pure LDPE matrix and the concentration of wt. 10% of such nanocarriers provided the optimum final LDPE/10TEO@SBE-15 active packaging film. This material could be a potential future product for active packaging applications.

Objective The aim of this study was to examine the impact of a modern lifestyle on college female students' health, specifically focusing on their hip and knee joint mobility. The objective of this study was to assess the influence of hydraulic resistance training with the self-myofascial release technique on improving joint mobility in female college students. The training also aimed to compare the effectiveness of hydraulic resistance exercise with and without the self-myofascial release technique on hip and knee joint mobility.Methods The study used a randomized controlled trial design to recruit 30 female college students aged 18-25 through campus advertisements and announcements. Medical conditions or injuries that might have affected participation was screened. Participants were indiscriminately allocated to Group A (Hydraulic Resistance Training with Self-Myofascial Technique) or Group B (Hydraulic Resistance Training without Self-Myofascial Technique). The baseline assessments included joint range of motion (ROM) measurements using a goniometer. Certified trainers supervised the training sessions, and the data were analyzed using SD and mean using SPSS. ResultsThis study aimed to evaluate the impact of hydraulic resistance training with self-myofascial release on hip and knee joint mobility in female college students. The results showed that both groups showed improved hip and knee flexion with and without the self-myofascial release technique. However, the Group A using the self-myofascial release technique (Group A) showed a more significant enhancement, as indicated by the smaller p value compared to Group B. It has been suggested that the self-myofascial release technique may improve hip and knee joint mobility. ConclusionThis study concluded that Hydraulic Resistance Training with Self-Myofascial Release (HSMR) could improve hip and knee joint mobility among female college students. These findings suggest that integrating the self-myofascial release technique into training regimens can improve joint mobility. However, further research with larger sample sizes and extended intervention periods was needed to understand the long-term effects and sustainability of these improvements.

In this paper, corticosteroid–β-cyclodextrin (β-CD) inclusion complexes have been prepared by Supercritical AntiSolvent (SAS) precipitation to enhance the dissolution rate of dexamethasone (DEX) and prednisolone (PRED), which are poorly water-soluble drugs. The processing of the active principles in the absence of a carrier led to the almost complete extraction of the active principle (the small amount of obtained material precipitates in the form of crystals). The coprecipitation of the ingredients in the presence of β-CD was investigated at different concentrations, pressures, and molar ratios. For both the corticosteroids, the optimized operating conditions were 40 °C, 120 bar, an equimolar ratio, and a concentration in DMSO of 20 mg/mL; these conditions led to the attainment of microparticles with a mean diameter equal to 0.197±0.180 μm and 0.131±0.070 μm in the case of DEX and PRED, respectively. The Job’s method confirmed the formation of inclusion complexes in correspondence with the 1/1 mol/mol ratio. Compared to the pure ingredients, the obtained powders have an improved release rate, which is about 3 times faster in both cases.

CO2 is widely used in the prevention and control of coal spontaneous combustion. In this manuscript, three low-rank coals with different metamorphic degrees were selected as the research objects. The temperature-programmed experiments, in-situ infrared cooling experiments, simulation of competitive adsorption of CO2 and O2 in coal pores, and simulation study of CO2 inhibition of coal oxygen composite reaction were used to obtain the role and effect of CO2 in preventing oxygen adsorption in coal at low-temperature oxidation stage. It is concluded that CO2 can displace the O2 near the pore wall to physically prevent the adsorption of O2. Through the change law of heating rate and kinetic analysis, it is found that CO2 can increase its activation energy by 5.3%-108.3% during the slow heating stage of coal, and reduce its heating rate. At around 120°C, coal loses the protective effect of CO2. From the changes of functional groups, it can be seen that when coal is cooled in CO2 atmosphere, mainly pyrolysis and condensation reactions occur due to the lack of O2. In addition, CO2 can also inhibit the chain reaction of coal's chemical adsorption of oxygen. This work provides a theoretical basis for CO2 prevention and control of coal spontaneous combustion.

With the current increase in the demand from animal and agricultural products, management of agrowaste has become critical to avoid greenhouse gas emissions. The present article investigates the applicability of ammonium bicarbonate synthesis via flash distillation to valorize and stabilize several types of anaerobic digestate produced from individual fermentations of amino acids. Prior to the development of the model in Aspen Plus v12, the description of the system aqua-ammonia-carbon dioxide provided by the electrolyte non-random two-liquid property method was validated with empirical data available in the literature. The content of CO₂ in the digestate was found to be responsible of the OH alkalinity (0.4 equivalents of acid/kg digestate), while the partial and total alkalinities (0.8 eq/kg digestate) were essentially derived from the content of NH₃. The most suitable conditions for the flash distillation were 95 ⁰C and 1 bar with the condensation occurring at 25 ⁰C. However, in order to attain the precipitation of NH₄HCO₃ in the distillate, it was necessary to consider digestates with a moisture content of 50 wt.%, since the minimum levels of inorganic nitrogen and inorganic carbon were not attained otherwise. Even under these conditions, few amino acids (i.e. arginine, glycine, and histidine) were able to provide an anaerobic digestate, upon fermentation, that would be suitable for NH₄HCO₃ stabilization. Despite alanine digestate and glutamine digestate presented sufficient concentrations of inorganic nitrogen and inorganic carbon, the NH₄HCO₃-stabilization was not feasible due to the limited volatilization of NH₃. The process of stabilization with a capacity of a tonne of digestate per hour was improved by adding hydrochloric acid or sodium hydroxide at rates 44 kg/h, leading to production of 34 kg NH₄HCO₃/h. The economic viability of this process needs to be investigated considering not only the market value of the isolated inorganic fertilizer but the carbon credits saved, resulting from handling a more stabilized organic manure. Furthermore, given the role of the volatile elements of the biogas as endogenous stripping agents, it is recommended to use a fresh and saturated digestate as feed for the flash distillation.

Dispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by chemical vapor deposition method (CVD) using novel precursor of the formula [Ag₅(O₂CC₂F₅)₅(H₂O)₃]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry (VT IR), and electron inducted mass spectrometry (EI MS). The morphology and the structure of the produced Ti6Al4V/AgNPs, and Ti6Al4V/TNT/AgNPs composites were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, measurements of hardness, Young’s modulus, adhesion, and surface free energy have been carried out. The ability to release silver ions from the surface of produced nanocomposite materials immersed in PBS solution has been estimated using inductively coupled plasma mass spectrometry (ICP MS). The wettability and the surface free energy of samples were estimated on the base of contact angle studies with the use of water and diiodomethane. Among the studied surface-modified titanium alloy implants, the best nano-mechanical properties were noticed for the Ti6Al4V/TNT15/AgNPs composite. The location of silver nanoparticles inside of titania nanotubes caused their lowest release rate, which may indicate on suitable properties above mentioned type of the composite for the construction of implants with a long term of antimicrobial activity.

Immunology and microbiology research in the West Indies has witnessed remarkable growth and innovation, playing a pivotal role in advancing our understanding of immune mechanisms, disease pathogenesis, and therapeutic interventions. This manuscript presents a comprehensive exploration of key areas in West Indian immunology research, spanning from the utilization of bacterial proteins as antibody reagents to the intricate realms of clinical immunology and disease management. The utilization of bacterial immunoglobulin-binding proteins (IBPs), including protein A (SpA), protein G (SpG), and protein L (SpL), has revolutionised serological diagnostics in the region. promise in early disease detection and precision medicine. Microbiological studies in the Caribbean region have shed light on antimicrobial resistance patterns, particularly the emergence of extended-spectrum beta-lactamases (ESBLs), guiding antimicrobial stewardship programs and informing therapeutic strategies. Clinical immunology research has elucidated the molecular pathways underlying immune-mediated disorders, leading to tailored management strategies for conditions such as severe combined immunodeficiency (SCID), neuropsychiatric lupus erythematosus (NPLE), and others. In summary, West Indian immunology and microbiology research has made significant contributions to global healthcare, fostering collaboration, innovation, and improved patient outcomes.

Several efforts have been made to estimate the prevalence of different types of antibiotic resistance in different regions of Nigeria. The study investigated the prevalence of Klebsiella pneumoniae encoding genes for CTX-M, TEM, and SHV-1 extended-spectrum beta-lactamases (ESBL) enzymes isolated from urine samples of non-hospitalized patients with suspected UTI in Lagos State, Nigeria. A 4-month retrospective study, spanning from May 2023 to August 2023, was conducted. K. pneumoniae was isolated from urine samples using standard microbiological methods. The modified Kirby-Bauer disc diffusion method was used to test for antibiotic susceptibility, and Clinical and Laboratory Standard Institute (CLSI) guidelines were followed for interpretation. The double-disk synergy method was used to confirm the phenotypic identity of ESBL producers, and the results were interpreted in accordance with CLSI guidelines. The phenotypic method was utilized for ESBL screening, employing the standard disk diffusion method. The CTX-M ESBL gene, TEM gene, and SHV gene were found using multiplex PCR. Results revealed that 41 K. pneumoniae isolates were resistant to third-generation Cephalosporins; the isolates showed resistance to ceftazidime in 100% of cases and ceftriaxone in 80.49% of cases respectively. It was determined that 8 (19.51%) of the isolates produced ESBL. Among Klebsiella isolates, the frequencies of the SHV, TEM, and CTX-M genes were 31 (75.61%), 4 (9.76%), and 10 (24.39%), in that order. Four isolates (9.67%) had the SHV, TEM, and CTX-M genes, while eight (19.51%) of the isolates possessed both the SHV and CTX-M genes. This investigation demonstrates high frequency, wide range of patterns and coexistence of ESBL genes in K. pneumoniae isolates from outpatient UTI patients. Although several phenotypic tests have been used for ESBL detection, testing directly for the presence of ESBL genes is always more accurate. The majority of the isolates of Klebsiella pneumoniae ESBL producers had the SHV gene identified.

Assuming a Winterberg model for space where the vacuum consists of a very stiff two component superfluid made up of positive and negative mass planckions, theory is the hypothesis, that Planck charge, , was created at the same time as Planck mass. Moreover, the repulsive force that like-mass planckions experience is, in reality, due to the electrostatic force of repulsion between like charges. These forces also give rise to what appears to be a gravitational force of attraction between two like planckions, but this is an illusion. In reality, gravity is electrostatic in origin if our model is correct. We determine the spring constant associated with planckion masses, and find that, , where equals Apery's constant, , and, , is the relaxed, i.e., , number density of the positive and negative mass planckions. In the present epoch, we estimate that, equals, , and the relaxed distance of separation between nearest neighbor positive, or negative, planckion pairs is, These values were determined using box quantization for the positive and negative mass planckions, and considering transitions between energy states, much like as in the hydrogen atom. For the cosmos as a whole, given a net smeared macroscopic gravitational field of, , due to all the ordinary, and bound, matter contained within the observable universe, an average displacement from equilibrium for the planckion masses is a mere , within the vacuum made up of these particles. On the surface of the earth, where, , the displacement amounts to, . All of these displacements are due to increased gravitational pressure within the vacuum, which in turn are caused by applied gravitational fields. The gravitational potential is also derived and directly related to gravitational pressure.

This paper presents an extended Kalman filter derivation for loosely coupled GPS (Global Positioning System)/INS (Inertial Navigation System) integration based on quaternion attitude representation using the Earth-Centered Earth (ECEF) Frame. In this loosely coupling integration, both the position and velocity estimates from GPS receiver are used as the measurements to extended Kalman filter, and then they are integrated with inertial measurements from inertial measurement units (IMU) to estimate the attitude, position and velocity of an air vehicle. The velocity estimates which have centimeter level estimation error from the GPS receiver are used to improve the filter performance. For attitude estimation, the global attitude parameterization is given by a quaternion and a multiplicative quaternion-error approach is used to guarantee a normalization constraint of quaternion in the filter. Simulation results are shown to obtain the estimation of the attitude, position, velocity, biases and scale factors and to evaluate the performance of the EKF with the measurement combination composed of the two different t

Prolonged high-intensity grinding can modify the crystal structure of solid substances and/or induce chemical reaction, which is referred to as mechanochemical reaction. Such reactions can exert positive influences on hydrometallurgical processes, therefore, many researchers have applied mechanochemical reactions for metals dissolution from minerals. The mechanism of mechanochemical reaction has been investigated using solid analyses and simulations. Structural changes caused by mechanochemical reaction are not yet sufficiently clarified because the ground samples are amorphous. The objective of this study was to analyze structural changes of cerianite in weathered residual rare earth ore by mechanochemical reduction. Structural change was analyzed by x-ray absorption near-edge structure and extended x-ray absorption fine structure analysis at the cerium L_III- and K-edges. These analyses revealed that the structural change of cerianite in this ore induced by mechanochemical reduction involved oxygen vacancy production. The process of the oxygen vacancy formation was closely coupled with the quantum effect of localization–delocalization of the 4f electron of cerium.

The voice contains elementary social communication cues, conveying speech, as well as paralinguistic information pertaining to the emotional state and the identity of the speaker. In contrast to vocal-speech and vocal-emotion processing, voice-identity processing has been less explored. This seems surprising, given the day-to-day significance of person recognition by voice. A valuable approach to unravel how voice-identity processing is accomplished is to investigate people who have a selective deficit in recognising voices. Such a deficit has been termed phonagnosia. In the present chapter, we provide a systematic overview of studies on phonagnosia and how they relate to current neurocognitive models of person recognition. We review studies that have characterised people who suffer from phonagnosia following brain damage (i.e. acquired phonagnosia) and also studies, which have examined phonagnosia cases without apparent brain lesion (i.e. developmental phonagnosia). Based on the reviewed literature, we emphasise the need for a careful behavioural characterisation of phonagnosia cases by taking into consideration the multistage nature of voice-identity processing and the resulting behavioural phonagnosia subtypes.

By using the new recently proposed extended rational methods, we set some solitary and multi wave solutions of the coupled Higgs system in the present study. Some new families of hyperbolic and trigonometric solutions of the coupled Higgs equations are successfully obtained. Some solutions are real as some are complex valued functions. Particular forms of some solutions derived by choice of some parameters are demonstrated in three dimensional spaces. The complex valued solutions are also depicted by plotting both real and complex component.

The properties of the charged dark matters are discussed in terms of the new three-dimensional quantized space model. Because of the graviton evaporations, the very small Coulomb’s constant (k(dd)) of 10 ⁻⁴⁸ k and large gravitation constant (G_N(dd)) of 10⁶ G_N for the charged dark matters at the present time are expected. The tentative values of G and k are used for the explanation purpose. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle. Also, the gravitation constant has been changed with increasing of the time because of the graviton evaporation. In the present work, the B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = 0 are explained as the good candidates of the dark matters. Also, the particle creation, dark matters and dark energy could be deeply associated with the changing gravitation constants (G). It is expected that the changing process of the gravitation constant between the matters from G_N(mm) ≈ 10³⁶ G_N to G_N(mm) = G_N happened mostly near the inflation period. Therefore, during most of the universe evolution the gravitation constant could be taken as G_N(mm) = G_N. And the effective charges and effective rest masses of the particles are defined in terms of the fixed Coulomb’s constant (k) and fixed gravitation constant (G_N). Then, the effective charge of the B1 dark matter with EC = −2/3 e is (EC)_eff = −2/3·10⁻²⁴ e. It is concluded that the photons, gravitons and dark matters are the first particles created since the big bang. The particles can be created from the decay of the matter universe and the pair production of the particle and anti-particle with decreasing of the gravitation constant (G_N(mm)). Also, the weak force, strong force and dark matter force bosons are created from the interactions of the elementary particles with the T fluctuations of the vacuum energy.

First, a recently developed eigenfunction expansion technique, based in part on separation of the thickness-variable and partly utilizing a modified Frobenius type series expansion technique in conjunction with the Eshelby-Stroh formalism, is employed to derive three-dimensional singular stress fields in the vicinity of the front of an interfacial crack weakening an infinite bicrystalline superlattice plate, made of orthorhombic (cubic, hexagonal and tetragonal serving as special cases) phases, of finite thickness and subjected to the far-field extension/bending, in-plane shear/twisting and anti-plane shear loadings, distributed through the thickness. Crack-face boundary and interface contact conditions as well as those that are prescribed on the top and bottom surfaces of the bicrystalline superlattice plate are exactly satisfied. It also extends a recently developed concept of lattice crack deflection (LCD) barrier to a superlattice, christened superlattice crack deflection (SCD) energy barrier for studying interfacial crack path instability, which can explain crack deflection from a difficult interface to an easier neighboring cleavage system. Additionally, the relationships of the nature (easy/easy, easy/difficult or difficult/difficult) interfacial cleavage systems based on the present solutions with the structural chemistry aspects of the component phases (such as orthorhombic, tetragonal, hexagonal as well as FCC (face centered cubic) transition metals and perovskites) of the superlattice are also investigated. Finally, results pertaining to the through-thickness variations of mode I/II/III stress intensity factors and energy release rates for symmetric hyperbolic sine distributed load and their skew-symmetric counterparts that also satisfy the boundary conditions on the top and bottom surfaces of the bicrystalline superlattice plate under investigation, also form an important part of the present investigation.

Background: Antibiotic-containing carrier systems are one option that offers the advantage of releasing active ingredients over a longer period of time. In vitro sustained drug release from a carrier system consisting of microporous β-TCP ceramic and alginate has been reported in previous works. Alginate dialdehyde (ADA) gelatin gel showed both better mechanical properties when loaded into a β-TCP ceramic and higher biodegradability than pure alginate. Methods: Dual release of daptomycin and BMP-2 was measured on days 1, 2, 3, 6, 9, 14, 21, and 28 by HPLC and ELISA. After release, the microbial efficacy of the daptomycin was verified and the biocompatibility of the composite was tested in cell culture. Results: Daptomycin and the model compound FITC protein A (n=30) were released from the composite over 28 days. A Daptomycin release above the minimum inhibitory concentration (MIC) by day 9 and a burst release of 71.7 ± 5.9 % were observed in the loaded ceramics. Low concentrations of BMP-2 were released from the loaded ceramics over 28 days.

: This article reports on polymer (PLLA, poly(L-lactic acid)) nanosheets incorporated with Fe-ion nanoparticles, aiming at using the latter nanoparticles as source to release Fe ions to facilitate burn wound healing when such nanosheets are applied on skin as biomedical tissue. Laser ablation in liquid phase was used to produce Fe-containing nanoparticles that after incorporation into PLLA nanosheets would release Fe ions when in immersed in water. Such nanoparticles prepared in chloroform are shown by XPS to be based on iron chloride and oxide phases. After incorporation into PLLA nanosheets, the ion –release test demonstrated that Fe ions could be released successfully into water at pH 7.4, which implies that such polymer nanosheets show promise for biomedical applications as potential patches for healing burn wounds. Incorporation with two different metal ions (Fe and Zn) is shown to be efficient and both types of ions were demonstrated to be released simultaneously and with comparable release rates.

Agriculture technical development exclusively relies on the effective delivery of agrochemicals and water to the plants and reduce the harmful effects of the agrochemicals on the useful organisms in the soil. Wherefore, super absorbent hydrogels were prepared by copolymerization of gum Arabic (GA) with chitosan (CS) or poly(vinyl alcohol) (PVA), and cross-linked by N,’N-methylenebisacrylamide (MBA) chemically (CH) or using sodium hexametaphosphate (SHMP) as physical (PH) cross-linker. The prepared hydrogels include PVA/GA-CH, PVA/GA-PH, CS/GA-CH and CS/GA-PH showed different degree of swelling (DS) in the following swelling medium, deionized water (DW), river water(RW) and buffer solution pH9. PVA/GA-CH and CS/GA-CH hydrogels have showed 84g/g and 63g/g maximum DS in RW respectively, while PVA/GA-PH and CS/GA-PH hydrogels have showed 81g/g and 69g/g maximum DS in pH9 respectively. The water- retention capability of some hydrogels were studied using a mixture of 0.5%(w/w) hydrogel in agricultural soil and the composite showed about 20 days extra retain of water with a control sample of soil alone. The hydrogels were loaded using urea the important fertilizer in agriculture field. The hydrogels of higher DS were only loaded, where PVA/GA-CH hydrogel has shown 89%(w/w) maximum loading percentage (Lmax%), and CS/GA-PH hydrogel reached 79.75%(w/w) of urea. The release behavior in different medium and degree of temperatures of loaded hydrogels were studied. Generally, PVA/GA-CH hydrogel have shown better release profile in RW medium at 10oC, while CS/GA-PH hydrogel showed more controlled release in pH9 medium at 30oC. Different analytical methods of SEM, FTIR of loaded hydrogel and after their release were achieved, whereas XRD,1H NMR and (TGA, DSC) of prepared hydrogels have been characterized.

Nutrient release from marine sediments in Osaka Bay has a significant impact on nutrient concentrations in seawater. A tsunami induced by the Nankai Trough earthquake may disturb marine sediments in the inner part of Osaka Bay. An incubation experiment to estimate the release rates of NH4-N and PO4-P was conducted to understand the present conditions and to quantify the changes caused by tsunamis. Two types of cores were created: a "control core" representing the current sediment, and a "redeposition core" representing the redeposition after the tsunami. The release rates have been decreasing since the year 2000 and have remained low. The experimental results suggest that the release rate after exposure to an aerobic environment by a tsunami may decrease to approximately 70% for NH4-N and 60% for PO4-P of the current level. In the past, the release rates were values experienced in the inner part of Osaka Bay. However, the reduction in the release rate by tsunamis may be more limiting for primary production under the current situation where the contribution of release for nutrients in seawater is significant.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for 6 d at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after 6 d of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after 6 d were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.

1. Darwin’s naturalization hypothesis predicts that alien species closely related to native species are less likely to naturalize because of strong competition due to niche overlap. Closely related species are likely to attract similar herbivores and to release similar plant volatiles following herbivore attack, thus could attract the same predators. However, the importance of phylogenetic relatedness on the interaction between alien and native plants has never been tested in a multitrophic context. 2. In a mesocosm experiment we grew six alien target plant species alone and in competition with nine native plant species of varying phylogenetic relatedness. To test the effects of multitrophic interactions on the performance of alien target species, we used enclosure cages to expose plants to the presence and absence of herbivorous arthropods, predatory arthropods and nematodes. 3. Surprisingly, biomass and number of flowering structures increased with presence of competitors for some of the alien species, but overall there was no consistent competition effect. Similarly, we found that none of the multitrophic-interaction treatments affected survival, biomass or number of flowering structures of the alien species. 4. We conclude there was no significant relationship between performance measures of the alien species and their phylogenetic relatedness to the native competitors.

The mathematical structure underlying a sentence is made of two independent processing units in series. The conditional probability density function of sentence length (measured in words) recordable in the extended short–term memory (E–STM) buffer made of CF cells is Gaussian. The number of sentences that authors of Italian and English Literatures have written is compared to that theoretically available to them. The multiplicity factor α describes this comparison. α&gt;1 is more likely than α&lt;1 and often α≫1, therefore the same sentence pattern is reused many times. These texts are easier to read. Very few novels show α&lt;1. In these cases, there are enough diverse sentence patters to convey meaning, but most of them are not used. Texts are more difficult to read, as measured by a universal readability index GU. A mismatch index IM synthetically describes the process. α, GU. and IM increase with year of publication. Future work will concern other literatures – including ancient ones as Greek and Latin – to confirm what, in our opinion, is general feature of human mind.

Background: Idiopathic normal pressure hydrocephalus is a syndrome with neuroradiological findings and clinical pattern characteristic but not specific for the pathology. Since the prevalence is growing due to the rapidly aging society, standardized and validated protocol for diagnosis is needed, also because this condition may mimic other disorders among elderly such as Parkinson's and Alzheimer's disease. Material and methods: We analysed data from 44 patients with suspect diagnosis of idiopathic normal pressure hydrocephalus with age > 60 years, clinical triad and neuroradiological pattern examined in our ward from November 2018 to November 2022. Neu-ropsychological assessment includes Mini Mental State Examination and Mental Deterioration Battery. Motor scores were collected from gait and balance tests. The evaluation was performed before and after an extended lumbar drainage last 48h. Patients who has scores improvement after the extended lumbar drainage, undergo ventriculoperitoneal shunt with a programmable valve. Results: All patients undergo neuropsychological assessment and motor tests, only 2 patients were unable to perform motor tests because bedridden. 16 patients showed no benefit from the tests, in 2 cases even a worsening of cognitive performance. 28 patients showed an improvement in their performances, but in most cases the improvement involved only the neuropsychological as-sessment. All patients underwent ventriculoperitoneal shunt have had a typical answers pattern in Mental Deterioration Battery test. We performed 9 ventriculoperitoneal shunt and 1 ventricu-lo-atrial shunt. Conclusions: Qualitative neurocognitive tests come out to be more sensitive compared to quantitative neurocognitive tests in identifying patients with suspected idiopathic normal pressure hydrocephalus benefiting from extended lumbar drainage test and then un-derwent surgical treatment. This could be considered a valid screening in elderly patients with suspected idiopathic normal pressure hydrocephalus in order to minimize the number of invasive procedures. More studies are necessary to validate this tool.

Firstly, a new set of Quasi-Cubic Trigonometric Bernstein basis with two tension shape parameters is constructed, and we prove that it is an optimal normalized totally basis in the framework of Quasi Extended Chebyshev space. And the Quasi-Cubic Trigonometric Bézier curve is generated by the basis function and the cutting algorithm of the curve are given, the shape features (cusp, inflection point, loop and convexity) of the Quasi-Cubic Trigonometric Bézier curve are analyzed by using envelope theory and topological mapping; Next we construct the non-uniform Quasi-Cubic Trigonometric B-spline basis by assuming the linear combination of the optimal normalized totally positive basis have partition of unity and continuity, and its expression is obtained. And the non-uniform B-spline basis is proved to have totally positive and high-order continuity. Finally, the non-uniform Quasi Cubic Trigonometric B-spline curve and surface are defined, the shape features of the non-uniform Quasi-Cubic Trigonometric B-spline curve are discussed, and the curve and surface are proved to be continuous.

Here, I introduce a concept called autonomous selection to refer to a source of selection that is part of the individuals upon which it acts. The concept is motivated by a set of phenomena with the following characteristics: Natural selection shaped a variant (e.g., gene, epigenetic mark, or combination thereof) to act in a manner that reduces the frequency of one or more heritable traits of the individual in which it is located if those traits are detrimental to individual or group fitness. Phenomena with these characteristics are peculiar to traditional evolutionary theory but have been identified rather frequently in recent decades. They are also relevant to adaptive evolution: By reducing the frequency of a trait detrimental to fitness, the variant accelerates the evolution of adaptations, which allows its holders to adapt better to constantly changing environments. The variant is shaped by (natural) selection, but also does (autonomous) selection. Several phenomena with these characteristics have been invoked by proponents of the extended evolutionary synthesis (EES). The concept of autonomous selection helps resolve some of the controversy surrounding the EES: EES proponents call attention to the incompleteness of contemporary theory, emphasizing individuals’ processes that influence which adaptations those individuals evolve. I argue for the special importance of individuals’ processes that do not just influence those individuals’ adaptations, but also accelerate the adaptive evolution of those individuals. All known phenomena that fit this description are examples of autonomous selection. Other phenomena raised by EES proponents do not meet this threshold.

After developed the formulation of a "general relativity" in C⁴ [2], we proceed with the formulation of a Hamilton-Jacobi equation in C⁴. We argue that in this consideration, the usual problems of the ADM formalism, do not exist, due to the complex time as it exists in our consideration. Specically, we can derive a suitable dispersion relation in order to work with and nd a generalised super Hamiltonian

In this paper, we define a (p,v)-extension of Hurwitz-Lerch Zeta function by considering an extension of beta function defined by Parmar et al. [J. Classical Anal. 11 (2017) 81–106]. We obtain its basic properties which include integral representations, Mellin transformation, derivative formulas and certain generating relations. Also, we establish the special cases of the main results.

Introduction: Tuberculosis (TB) is one of the most prevalent respiratory diseases in the world. In 2020 there were at least 9.9 million new infections, with 1.5 million deaths. Approximately 10% of people infected with Mycobacterium tuberculosis (LTBI) develop the disease during the first 2 to 5 years after infection. Currently in South America, the diagnosis of LTBI continues to be per-formed through the Mantoux tuberculin skin test (TST). Objective: The objective of our study was to compare the sensitivity of a new immunofluorescence IGRA test against a widely available IGRA kit on the market. Material and method: Close contact to infectious patients with TB, or HIV patients or immunocompromised for another cause were recruited. Two interferon gamma release assay (IGRA) diagnostic kits were used and compared with TST. Results: 76 patients were recruited. 93.42% were Chilean nationality, 98.68% of the patients did not have immunosuppres-sion. The sensitivity of the new technique was 88.89% and specificity 92.50% in the study popula-tion compared to the IGRA previously used. In the subgroup older than 36 years, the sensitivity was 95.65% and the specificity 89.47%. Conclusion: IGRA techniques are a new resource in clini-cal laboratories to be able to make an accurate diagnosis in LTBI in the region of the Americas. In our population, the greatest benefit of this new IGRA would be observed in people over 36 years of age, where the sensitivity of the technique was like that of the currently available test.

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

Diabetes mellitus (DM) is one of the principal manifestations of metabolic syndrome and its prevalence with modern lifestyle is increasing incessantly. Chronic hyperglycemia can induce several vascular complications that were referred to be the major cause of morbidity and mortality in DM. Although several therapeutic targets have been identified and accessed clinically, the imminent risk of DM and its prevalence are still ascending. Substantial pieces of evidence revealed that histone deacetylase (HDAC) isoforms can regulate various molecular activities in DM via epigenetic and post-translational regulation of several transcription factors. To date, 18 HDAC isoforms have been identified in mammals that were categorized into 4 different classes. Classes I, II, and IV are regarded as classical HDACs, which operate through a Zn-based mechanism. In contrast, class III HDACs or Sirtuins depend on nicotinamide adenine dinucleotide (NAD+) for their molecular activity. Functionally, most of the HDAC isoforms can regulate β cell fate, insulin release, insulin expression and signaling, and glucose metabolism. Moreover, the roles of HDAC members have been implicated in the regulation of oxidative stress, inflammation, apoptosis, fibrosis, and other pathological events, which substantially contribute to diabetes-related vascular dysfunctions. Therefore, HDACs could serve as the potential therapeutic target in DM towards developing novel intervention strategies. This review sheds light on the emerging role of HDACs/isoforms in diabetic pathophysiology and emphasized the scope of their targeting in DM for constituting the novel interventional strategies for metabolic disorders/complications.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

Renewable resources gain increasing interest as source for environmentally benign biomaterials, such as drug encapsulation/release compounds, and scaffolds for tissue engineering in regenerative medicine. Being the second largest naturally abundant polymer, the interest in lignin valorization for biomedical utilization is rapidly growing. Depending on resource and isolation procedure, lignin shows specific antioxidant and antimicrobial activity. Today, efforts in research and industry are directed toward lignin utilization as renewable macromolecular building block for the preparation of polymeric drug encapsulation and scaffold materials. Within the last five years, remarkable progress has been made in isolation, functionalization and modification of lignin and lignin-derived compounds. However, literature so far mainly focuses lignin-derived fuels, lubricants and resins. The purpose of this review is to summarize the current state of the art and to highlight the most important results in the field of lignin-based materials for potential use in biomedicine (reported in 2014–2018). Special focus is drawn on lignin-derived nanomaterials for drug encapsulation and release as well as lignin hybrid materials used as scaffolds for guided bone regeneration in stem cell-based therapies.

A transform approach based on a variable initial time (VIT) formulation is developed for discrete-time signals and linear time-varying discrete-time systems or digital filters. The VIT transform is a formal power series in z^(-1) which converts functions given by linear time-varying difference equations into left polynomial fractions with variable coefficients, and with initial conditions incorporated into the framework. It is shown that the transform satisfies a number of properties that are analogous to those of the ordinary z-transform, and that it is possible to do scaling of z^(- i) by time functions which results in left-fraction forms for the transform of a large class of functions including sinusoids with general time-varying amplitudes and frequencies. Using the extended right Euclidean algorithm in a skew polynomial ring with time-varying coefficients, it is shown that a sum of left polynomial fractions can be written as a single fraction, which results in linear time-varying recursions for the inverse transform of the combined fraction. The extraction of a first-order term from a given polynomial fraction is carried out in terms of the evaluation of z^(i) at time functions. In the application to linear time-varying systems, it is proved that the VIT transform of the system output is equal to the product of the VIT transform of the input and the VIT transform of the unit-pulse response function. For systems given by a time-varying moving average or an autoregressive model, the transform framework is used to determine the steady-state output response resulting from various signal inputs such as the step and cosine functions.

Tracking the kinematics of human movement usually requires the use of equipment that constrains the user within a room (e.g., optical motion capture systems), or requires the use of a conspicuous body-worn measurement system (e.g., inertial measurement units (IMUs) attached to each body segment). This paper presents a novel Lie group constrained extended Kalman filter to estimate lower limb kinematics using IMU and inter-IMU distance measurements in a reduced sensor count configuration. The algorithm iterates through the prediction (kinematic equations), measurement (pelvis height assumption/inter-IMU distance measurements, zero velocity update for feet/ankles, flat-floor assumption for feet/ankles, and covariance limiter), and constraint update (formulation of hinged knee joints and ball-and-socket hip joints). The knee and hip joint angle root-mean-square errors in the sagittal plane for straight walking were 7.6±2.6∘ and 6.6±2.7∘, respectively, while the correlation coefficients were 0.95±0.03 and 0.87±0.16, respectively. Furthermore, experiments using simulated inter-IMU distance measurements show that performance improved substantially for dynamic movements, even at large noise levels (σ=0.2 m). However, further validation is recommended with actual distance measurement sensors, such as ultra-wideband ranging sensors.

Wound infection is a common complication of chronic wounds. It can impair healing, which may not occur without external help. Antimicrobial dressings (AMDs) are a type of external help to infected chronic wounds. In this study, highly porous membranes made of only chitosan and containing the antiseptic polyhexanide (poly(hexamethylene biguanide); PHMB) were prepared by cryogelation, aiming to be used in AMDs. These membranes exhibited high water swelling capacity, fast water absorption and high water vapor transmission. The best drug loading method involved simultaneous loading by soaking in a PHMB solution and sterilization by autoclaving, resulting in sterilized, drug-loaded membranes. The drug release kinetics was comparable to that of a commercial PHMB-releasing AMD assayed under the same conditions. These membranes exhibited high antibacterial activity against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa, which are bacterial species commonly found in infected wounds, and blood clotting activity. The obtained results suggest that these membranes may be suitable for use in the development of AMDs.

Perception of flavor is a dynamic process during which the concentration of aroma molecules at the olfactory epithelium varies with time as they are released progressively from the food in the mouth during consumption. The release kinetics depends on the food matrix itself, but also on food oral processing, such as mastication behavior and food bolus formation with saliva, for which huge inter-individual variations exist due to physiological differences. Sensory methods, such as time-intensity (TI), or the more recent methods temporal dominance of sensations (TDS) and temporal check-all-that-apply (TCATA), are used to account for the dynamic and time-related aspects of flavor perception. Direct injection mass spectrometry (DIMS) techniques that measure in real-time aroma compounds directly in the nose (nosespace), aimed at obtaining data that reflect the pattern of aroma release in real-time during food consumption, supposed to be representative of perception, have been developed since 25 years. Examples obtained with MS operated in chemical ionization mode at atmospheric or sub-atmospheric pressure (atmospheric pressure chemical ionization APCI or proton transfer reaction PTR) will be given, with emphases on studies conducted with simultaneous dynamic sensory evaluation. Inter-individual variations in terms of aroma release and their relevance for understanding flavor perception will be discussed, as well as evidenced cross-modal interactions.

Nowadays, bioeconomy and nanotechnology trends push food packaging sector in the re-placement of food additives by biobased antioxidant/antibacterial compounds and their inclusion in nanocarriers to control their release. Herein by following this trend, a rich in thymol-(TO) activated carbon (AC) nanostructure (TO@AC) was prepared and physiochemically characterized with various technics. This TO@AC nanostructure as well as pure AC were extruded with low density polyethylene (LDPE) to develop novel active packaging LDPE/TO@AC and LDPE/AC films. X-ray diffractometry, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy measuraments shown high dispersity and capability of both AC and TO@AC in LDPE matrix which was resulted in enhanced tensile and water/oxygen barrier properties of obtained LDPE/AC and LDPE/TO@AC films. LDPE/TO@AC films shown higher elongation at break values and water/oxygen barrier than LDPE/AC films and significant antioxidant activity. TO release kinetics studies shown that by increasing TO@AC content the total TO amount released increased and the constant release rate decreased. Pork fillets wrapped with the optimum active film containing 15 wt.% TO@AC and succeed to prevent lipid oxidation and heme iron loss during storage. Estimation of microbial population of pork fillets shown that this active film could ex-tend the microbiological shelf-life of pork fillets by 2 days

Promoting the use of solar energy resources has always faced the challenges of instability and supply-demand mismatch. The key to solving these issues is to efficiently store and utilize solar energy resources using high-performance heat storage devices. This study designed a high-performance shell-and-tube phase change thermal storage device and established a numerical model using ANSYS software to summarize the device's dynamic melting law. To verify the accuracy of the numerical simulation, a performance testing platform for the phase change thermal storage device was built to investigate the impact of factors such as inlet water temperature, inlet water flow rate, type of heat storage, and initial temperature of the device, and to reveal the change law of the device's performance. The results show that the inlet water temperature has the most significant impact on the device's heat storage and release performance. When the device's heat storage or release is used for heating, changing the inlet water flow rate has a weak and limited effect on the device's performance. However, when the device's heat release is used to provide domestic hot water, increasing the makeup water temperature and reducing the inlet water flow rate can significantly improve the device's effective heat release. Furthermore, based on the experimental validation of the model's correctness, this study further simulated and studied the impact of different factors on the device's heat storage process to optimize its structural design and provide technical references for the device's actual operation and installation. The results show that the placement of fins has a negligible effect on the performance of the heat storage device while reducing the fin spacing and increasing the fin thickness can significantly improve the melting efficiency of the phase change material (PCM). Additionally, the heat storage characteristics of the device are significantly better in the vertical installation mode than in the horizontal installation mode. This study provides theoretical guidance and technical references for the design and use of phase change thermal storage devices.

The prevalence for chronic, non-healing skin wounds in the general population, most notably diabetic foot ulcers, venous leg ulcers and pressure ulcers, is approximately 2% and is expected to increase, driven mostly by an aging population and the steady rise in obesity and diabetes. Non-healing wounds often become infected, increasing the risk of life-threatening complications, which poses a significant socioeconomic burden. Aiming at an improved management of infected wounds, a variety of wound dressings incorporating antimicrobials (AMDs), namely polyhexanide (poly(hexamethylene biguanide); PHMB), have been introduced in the wound care market. However, many wound care professionals agree that none shows comprehensive and optimal antimicrobial activity. This manuscript summarizes and discusses studies on novel PHMB-releasing membranes (PRMs) for wound dressings, detailing their preparation, physical properties relevant in the context of AMDs, drug loading and release, antibacterial activity, biocompatibility, wound healing capacity, and clinical trials conducted. Some of these PRMs were able to improve wound healing in in vivo models, with no associated cytotoxicity, but significant differences in study design make it difficult to compare overall effi-cacies. It is hoped that this review, which includes, whenever available, international standards for testing AMDs, will provide a framework for future studies.their preparation, physical properties relevant in the context of AMDs, drug loading and release, antibacterial activity, biocompatibility, wound healing capacity, and clinical trials conducted. Some of these PRMs were able to improve wound healing in in vivo models, with no associated cytotoxicity, but significant differences in study design make it difficult to compare overall efficacies. It is hoped that this review, which includes, whenever available, international standards for testing AMDs, will provide a framework for future studies.

Films prepared from poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers produced by Aneurinibacillus sp. H1 using an automatic film applicator were homogeneous and had a defined thickness, which allowed a detailed study of physicochemical properties. Their properties were compared with a poly (3-hydroxybutyrate) homopolymer film prepared by the same procedure, which proved to be significantly more crystalline by DSC and XRD. Structural differences between samples had a major impact on their properties. With increasing 4-hydroxybutyrate content, the ductility and release rate of the model hydrophilic active ingredient increased significantly. Other observed properties, such as the release of the hydrophobic active substance, the contact angle with water and ethylene glycol, or the surface morphology and roughness, were also affected by the composition. The identified properties predetermine these copolymers for wide use in areas such as biomedicine or smart biodegradable packaging for food or cosmetics. The big advantage is the possibility of fine-tuning properties simply by changing the fermentation conditions.

Nanotechnology has enabled the development of novel therapeutic strategies such as targeted nanodrug delivery systems, control and stimulus-responsive release mechanisms, and the production of theranostic agents. As a prerequisite for the use of nanoparticles as drug delivery systems, the amount of loaded drug must be precisely quantified, a task for which two approaches are currently used. However, both approaches suffer from the inefficiencies of drug extraction and of the solid-liquid separation process, as well as from dilution errors. This work describes a new, reliable, and simple method for direct drug quantification in polymeric nanoparticles using attenuated total reflection Fourier transform infrared spectroscopy, which can be adapted for a wide variety of drug delivery systems. Silk fibroin nanoparticles and naringenin were used as model polymeric nanoparticle carrier and drug, respectively. The specificity, linearity, detection limit, precision and accuracy of the spectroscopic approach were determined in order to validate the method. A good linear relation was observed within 0.00 to 7.89 % of naringenin relative mass with an R2 of 0.973. The accuracy was determined by the spike and recovery method. Results showed an average 104% recovery. The limit of detection and limit of quantification of the drug loading content were determined to be 0.3 and 1.0 %, respectively. The method's robustness is demonstrated by the notable similarities between the calibrations carried out in two different equipment and institutions.

High rates of phosphorus (P) currently being applied to soils for the production of vegetables in the Mekong Delta, Vietnam has led to the concern of its negative effect on the economics and the environment. This research presents a comprehensive study on the determination of P supplying capacity in this region of Vietnam to examine the possibility of reducing P fertilizer input. One hundred twenty (120) soil samples were collected to evaluate total P and Bray 1 available P in the soils. Phosphorus maximum sorption, degree of P saturation, P release, and the effect of P fertilizer on corn (Zea mays L.) yield in greenhouse and fields were also determined. Total P concentrations of 56.7% soil samples evaluated yielded high P concentrations (>560 mg P/kg), while 74.2% of the samples had high Bray 1 available P concentrations (>20 mg P/kg soil). Maximum P sorption ranged from 149 to 555 mg P/kg soil, respectively and has negative correlation to available P (r = - 0.63*), degrees of P saturation ranged from 0.63 to 5.46% correlated to available P (r = 0.98**) and maximum P release ranged from 1.2 to 61.9 mg P/kg soil, respectively correlated to available P (r = 0.96**). Corn grown in soils with available P concentrations >15 mg P/kg did not respond to P fertilizer in greenhouse or field experiments. We conclude that many farmers in this region can reduce P fertilizer input, thus increasing their profits and reducing negative environmental impacts associated with excess soil P for sustainable agriculture.

The flux growth of InVO4 bulk single crystals has been explored for the first time. The reported eutectic composition at a ratio of V2O5:InVO4 = 1:1 could not be used as a self-flux, since no sign of melting was observed up to 1100 °C. Crystals of InVO4 of typical size 0.5×1×7 mm3 were obtained using copper pyrovanadate (Cu2V2O7) as a flux, using Pt crucibles. XRD confirmed the orthorhombic Cmcm structure. Rests of flux material were observed on the sample surface, with occasional traces of Pt indicating some level of reaction with the crucible. X-ray absorption spectroscopy showed that oxidation states of indium and vanadium ions are +3 and +5, respectively. The size and high quality of the obtained InVO4 crystals makes them excellent candidates for the further study of their physical properties.

In the upper charged layers of the atmosphere, the plasma is very rarefied. The collisions between its molecules are almost non-existent, and the driving forces behind them are the Lorentz forces resulting from the electric and magnetic fields. For this reason, we are interested in studying the behavior of non-collision plasmas because of its essential applications, such as the movement of satellites in the charged atmosphere. In this paper, the flow problem of collisionless gaseous plasma is examined. For that propose, we solve the unsteady Vlasov-Maxwell system of non-linear partial differential equations analytically. Methods of moments and traveling wave parameters are used to acquire an exact solution. Specific macroscopic properties of collisionless gaseous plasma are calculated along with electrical and magnetic fields. Further, thermodynamic estimation, such as entropy and entropy production, is presented. Those calculations allow us to measure the consistency with the laws of non-equilibrium thermodynamics. Relations between internal energy modification participations are predicted using Gibbs' equation for collisionless plasma. The modification effect of internal energies due to electro-magnetic fields is found to be small compared with the internal energy change due to the effect of entropy. That is because these fields are self-induced by plasma particles due to the sudden movement of the rigid plane plate. The results are accomplished according to the typical argon gaseous plasma model. Three-dimensional diagrams showing the measured variables are drawn to investigate and discuss their behavior. The problem has many commercial applications for the movement of objects in the charged atmosphere.

In the present work, the charged B1, B2 and B3 bastons with the condition of k(mm) = k >> k(dd) > k(dm) = k(lq) = 0 are explained as the good candidates of the dark matters. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. The missing neutrinos are newly explained by using the dark matters and lepton charge force. The neutrino excess anomaly of the MinibooNE data is explained by the B1 dark matter scattering within the Cherenkov detectors. And the rest masses of 1.4 TeV/c² and 42.7 GeV/c² are assigned to the Le particle and the B2 dark matter, respectively, from the cosmic ray observations. In the present work, the Q1 baryon decays are used to explain the anti-Helium cosmic ray events. Because of the graviton evaporation and photon confinement, the very small Coulomb’s constant (k(dd)) of 10^x-54k and gravitation constant (G_N(dd)) of 10^xG_N for the charged dark matters at the present time are proposed. The x value can have the positive, zero or negative value around zero. Therefore, F_c(mm) > F_g(dd) (?) F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = F_c(lq) = 0 for the proton-like particle.

Recently, different extensions of the fractional derivative operator are found in many research papers. The main aim of this paper is to establish an extension of the extended Caputo fractional derivative operator. The extension of an extended fractional derivative of some elementary functions derives by considering an extension of beta function which includes the Mittag-Leffler function in the kernel. Further, an extended fractional derivative of some familiar special functions, the Mellin transforms of newly defined Caputo fractional derivative operator and the generating relations for extension of extended hypergeometric functions also presented in this study.

The main objective of this present paper is to introduce further extension of extended Caputo fractional derivative operator and establish the extension of an extended fractional derivative of some known elementary functions. Also, we investigate the extended fractional derivative of some familiar special functions, the Mellin transforms of newly defined Caputo fractional derivative operator and generating relations for extension of extended hypergeometric functions.

Ante-mortem bovine tuberculosis (bTB) tests for buffaloes include the single comparative intradermal tuberculin test (SCITT), interferon-gamma (IFN-γ) release assay (IGRA) and IFN-γ-inducible protein 10 release assay (IPRA). Although parallel test interpretation increases detection of Mycobacterium bovis-infected buffaloes, these algorithms may not be suitable for screening buffaloes in historically bTB-free herds. In this study, the specificities of three assays were determined using M. bovis unexposed herds, and a high specificity diagnostic algorithm developed. Serial test interpretation using the IGRA and IPRA showed significantly greater specificity (98.3%) than individual tests or parallel testing (73%). When the SCITT was added, the algorithm had a 100% specificity. Since the cytokine assays had imperfect specificity, potential cross-reactivity with nontuberculous mycobacteria (NTM) was investigated. No association was found between NTM presence (in oronasal swab cultures) and positive cytokine assay results. As a proof-of-principle, serial testing was applied to high-value buffaloes (n=153) in a historically bTB-free herd. Buffaloes positive on a single test (n=28) were regarded as test negative. Four buffaloes were positive on IGRA and IPRA, and M. bovis infection was confirmed following culling. These results demonstrate the value of using IGRA and IPRA in series to screen buffalo herds with no previous history of M. bovis infection.

Mitochondrial dysfunctions, e.g. abnormal handling of mitochondrial DNA in TFAM mutants or in altered mitophagy, activate innate immunity. Recent reports also showed that deletion of mitochondrial matrix peptidase ClpP in mice transcriptionally upregulates inflammatory factors. Here, we studied ClpP-null mouse brain at two ages and embryonal fibroblasts, to identify which signaling pathways are responsible, employing mass spectrometry, immunoblots, and reverse transcriptase polymerase chain reaction. Anomalies in the mitochondrial unfolded protein responses pathway were prominent for the co-chaperone DNAJA3, and for its known interactor STAT1. Their mitochondrial dysregulation affected also their extra-mitochondrial abundance, as possible innate immune modulators. Increased expression was observed not only for the transcription factors Stat1/2, but also for two interferon-stimulated genes (Ifi44, Gbp3). Inflammatory responses were strongest for RLR pattern recognition receptors (Ddx58, Ifih1, Oasl2, Trim25) and several cytosolic nucleic acid sensors (Ifit1, Ifit3, Oas1b, Ifi204, Mnda). They can be explained by the accumulation of mitoribosomes and mitochondrial nucleoids in ClpP-null cells, which may act as damage-associated molecular patterns. The consistent dysregulation of these factors from early age might influence also human Perrault syndrome, where ClpP loss-of-function leads to early infertility and deafness, with subsequent widespread neurodegeneration.

SARS-CoV-2 is a new coronavirus that has caused a worldwide pandemic. It produces severe acute respiratory disease (COVID-19), which is fatal in many cases, characterised by cytokine release syndrome (CRS). According to the World Health Organization (WHO), those who smoke are likely to be more vulnerable to infection. Here, in order to clarify the epidemiologic relationship between smoking and COVID-19, we present a systematic literature review until 28 April 2020 and a meta-analysis. It includes 18 recent COVID-19 clinical and epidemiological studies based on smoking patient status from 720 initial studies in China, USA, and Italy. The percentage of hospitalised current smokers was 7.7% (95%CI: 6.9-8.4) in China, 2.3% (95%CI: 1.7-2.9) in the USA and 7.6% (95%CI: 4.2-11.0) in Italy. These percentages were compared to the smoking prevalence of each country and statistically significant differences were found in them all (p <0.0001). By means of the meta-analysis, we offer epidemiological evidence showing that smokers were statistically less likely to be hospitalised (OR=0.18, 95%CI: 0.14-0.23, p<0.01). CRS and exacerbated inflammatory response are associated with aggravation of hospitalise patients. In this scenario, we hypothesise that nicotine, not smoking, could ameliorate the cytokine storm and severe related inflammatory response through the cholinergic-mediated anti-inflammatory pathway.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

Cyber diplomacy is critical in dealing with evolving cybersecurity dangers and possibilities in the digital era. This article investigates the impact of Artificial Intelligence (AI), the Internet of Things (IoT), Blockchains, and Quantum Computing on cyber diplomacy. AI holds the potential for proactive threat identification and response, while IoT enables international information sharing. Blockchains enable secure data sharing and document verification, but they also pose new threats, such as AI-driven cyber-attacks, IoT privacy breaches, blockchain vulnerabilities, and the potential for quantum computing to break encryption. This article conducts case study reviews, in combination with secondary data analysis, and emphasises the value of international cooperation in developing global norms and frameworks to control responsible technology adoption. Cyber diplomacy can promote cybersecurity, protect national interests, and foster mutual trust among nations in the digital sphere by capitalising on possibilities and reducing threats.

The i-4-1-Health project is a One Health project on the prevalence and spread of antimicrobial resistance in the human and veterinary domain in the Dutch-Belgian cross-border region. This paper describes the main components of the laboratory protocol that was developed to standardise the microbiological methods used for the detection of intestinal carriage of highly-resistant microorganisms.

We explore the field equations in a 4-d complex space-time, in the same way, that general relativity does for our usual 4-d real space-time, forming this way, a new "general relativity" in C⁴ space-time, free of sources. Afterwards, by embedding our usual 4-d real space-time in C⁴ space-time, we describe geometrically the energy-momentum tensor T_μν as the lost geometric information of this embedding. We further give possible explanation of dark eld and dark energy.

Radar transmit signal design is a critical factor for the radar performance. In this paper, we investigate the problem of radar signal waveform design under the small signal power conditions for detecting a doubly spread target, whose impulse response can be modeled as a random process, in a colored noise environment. The doubly spread target spans multiple range bins (range-spread) and its impulse response is time-varying due to fluctuation (hence also Doppler-spread), such that the target impulse response is both time-selective and frequency-selective. Instead of adopting the conventional assumption that the target is wide-sense stationary uncorrelated scattering,we assume that the target impulse response is both wide-sense stationary in range and in time to account for the possible correlation between the impulse responses corresponding to close range intervals. The locally most powerful detector, which is asymptotically optimal for small signal cases, is then derived for detecting such targets. The signal waveform is optimized to maximizing the detection performance of the detector or equivalently maximizing the Kullback-Leibler divergence. Numerical simulations validate the effectiveness of the proposed waveform design for the small signal power conditions and performance of optimum waveform design are shown in comparison to the frequency modulated waveform.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

The difficulties faced by the society in its goal of reducing mortality and improving the health status during the period of the COVID-19 pandemic showed that it is necessary to develop new approaches in the therapy of infectious diseases, leading to higher treatment efficiency and few side effects. The subject of the present study is the formation and characterization of the proper-ties of stable liposomes loaded with extracts from Bulgarian medicinal plants and monitoring their antiviral action against the human strain of coronavirus OC43 (HCoV-OC43) in vitro. The hydrodynamic diameter and -potential of the liposomes containing each type of payload were determined with DLS and electrokinetics. The encapsulated amount of extracts was evaluated against quercetin and gallic acid by using colourimetric methods. The BALB 3T3 Neutral Red Uptake (NRU) phototoxicity/cytotoxicity assay was used to estimate the safety of the compounds. For assessment of the antiviral activity against HCoV-OC43 of liposomes (Lip) containing medicinal plant extracts, the cytopathic effect inhibition test was used. Measurements of the virucidal activity and the effect on the virus adsorption stage was carried out using the endpoint dilution method, and ∆lgs were calculated by comparison with untreated controls. The estimated photo irritation factors (PIF) for the Lip containing extracts were < 2 which assigns them to the category of non-phototoxic substances. When the extracts were introduced into the liposomes as their carriers, the antiviral activity of the vesicles against the replication of HCoV-OC43 in vitro in-creased by several times compared to their individual activity described in our previous study. The determination of the effect of structures loaded with extracts on the extracellular virions and the stage of their adsorption to sensitive HCT-8 cells proved that the liposomes do not affect directly the viral surface or cell membrane, but only perform a function of carriers of the active substances and the observed result is due solely to the intracellular action of the extracts.

Anti-CD19 chimeric antigen receptor (CAR) T-cells represent a novel immunotherapy that has shown remarkable success in the treatment of adult relapsed or refractory (R/R) B-cell non-Hodgkin's lymphoma, adult R/R mantle cell lymphoma, and R/R acute paediatric lymphoblastic leukaemia. One barrier to the widespread use of CAR T-cell therapy is toxicity, primarily cytokine release syndrome (CRS) with a variable grade of severity. The main manifestations of CRS are fever, hypotension, cytopenia, organ dysfunction among others. Neurological toxicities vary widely and range from headaches to encephalopathy. In addition, anti-CD19 CAR T-cell therapy provokes an array of less frequent events, such as coagulopathies, delayed cytopenia, and cardiovascular toxicities. In general, toxicities are usually reversible and resolve on their own in most cases, though severe cases may require intensive care and immunosuppressive therapy. Deaths due to CRS, neurologic toxicity and infectious complications have been reported, which highlights the gravity of these syndromes and the critical nature of appropriate intervention. In this paper, we look at all available FDA- and EMA-approved information about the pathophysiology, clinical manifestations, risk factor reviews of existing toxicity grading systems, current management strategies, and guidelines for anti-CD19 CAR T-cell toxicities. We also present new approaches, which are under investigation, to mitigate these adverse events.

This research paper investigates ultra-wideband (UWB) localization systems by focusing on the use of average filter (AVG), Kalman filter (KF), and extended Kalman filter (EKF) algorithms, as well as a novel integrated filtering method that incorporates low-pass filter (LPF) into AVG, KF, and EKF. The study aims to improve localization loss in indoor environments using a TurtleBot robot equipped with a camera to observe ground truth positions. To evaluate the effectiveness of the proposed algorithms, a comprehensive comparison of the raw and filtered data with the camera-based ground truth observations is performed. Quantitative analyses of the results, including max, min, max-min, and mean error, are performed to evaluate the localization performance of the algorithms and the integrated filtering method. The results reveal that the integrated filtering method has performed better accuracy in comparison with existing methods.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

The pentose phosphate pathway (PPP) is one of three major pathways involved in glucose metabolism, regulated by glucose-6-phosphate dehydrogenase (G6PD), controlling NADPH formation. NADPH, in turn, regulates the balance of oxidative stress and reactive oxygen species (ROS) levels. G6PD dysfunction, affecting PPP, is implicated in neurological disorders, including epilepsy. However, PPP's role in epileptogenesis and ROS production during epileptic activity remains unclear. To clarify these points, we conducted electrophysiological and imaging analyses on mouse hippocampal brain slices. Using the specific G6PD inhibitor G6PDi-1, we assessed its effects on mouse hippocampal slices, examining intracellular ROS, glucose/oxygen consumption, and ROS production during synaptic stimulation and in the 4AP epilepsy model. G6PDi-1 increased basal intracellular ROS levels and reduced synaptically induced glucose consumption but had no impact on ROS production from synaptic stimulation. In the 4AP model, G6PDi-1 didn't significantly alter spontaneous seizure frequency or H2O2 release amplitude but increased the frequency and peak amplitude of interictal events. These findings suggest that short-term PPP inhibition has a minimal impact on synaptic circuit activity.

Food waste disposal to landfills practice contributes to greenhouse problem due to the emission of gases such as methane to the atmosphere. Shelf-life extension of food products and further valorization of food wastes such as the conversion to activated carbon are tested nowadays as alternative techniques. The development and use of biobased active coatings against food oxidation/bacterial deterioration is an environmentally friendly technique. In this study, a novel food active coating was successfully developed based on a chitosan (CS)/poly-vinyl alcohol (PVOH) matrix activated with a nanohybrid of natural thymol (TO) adsorbed in activated carbon (AC) derived from spent coffee. The results shown that, compared to the pure CS/PVOH polymeric matrix, the coating with 15% wt. TO@AC nanohybrid concentration achieved +23.5 % Young’s modulus value, +20.1% ultimate strength value, increased barrier of +50.2% for water and +74.0 % for oxygen, +69.0% antioxidant activity, increased antibacterial activity of +5.5% against Escherichia coli, +17.8% against Salmonella enterica, +42.5% against Staphylococcus aureus, and +2.5% against Listeria monocytogenes. A visual evaluation of this coating shown a delay to fresh bananas enzymatic browning and significantly decrease their weight loss. This indicates that it could be potentially used to extend the shelf-life of fresh fruits.

Coronavirus disease 2019 (COVID-19) from severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) infection has resulted in tremendous morbidity and mortality worldwide. A major underlying cause of COVID-19 mortality is a hyperinflammatory cytokine storm in severe/critically ill patients. Although many clinical trials are testing the efficacy of targeting inflammatory cytokines/chemokines in COVID-19 patients, the critical inflammatory mediator initiating COVID-19 patient death is undefined. Here we suggest that the immunopathological pathway leading to COVID-19 mortality can be divided into three stages with distinct clinical features that can be used to guide therapeutic strategies. Our interpretation of the recently published clinical trials from COVID-19 patients suggests that the clinical efficacy in preventing COVID-19 mortality using IL-1 blockade is subjected to notable caveats, while that for IL-6 blockade is suboptimal. We discuss critical factors in determining appropriate inflammatory cytokine/chemokine targets, timing, and combination of treatments to prevent COVID-19 mortality.

Studies have previously described the occurrence of multidrug-resistant (MDR) Escherichia coli in human and veterinary medical settings, livestock, and, to a lesser extent, in the environment and food. While they mostly analyzed foodborne E. coli regarding phenotypic and sometimes genotypic antibiotic resistance and basic phylogenetic classification, we have limited understanding of the in vitro and in vivo virulence characteristics and global phylogenetic contexts of these bacteria. Here, we investigated an E. coli strain (PBIO3502) isolated from a pork sausage in Germany in 2021 in-depth. Whole-genome sequence analysis revealed sequence type (ST)58, which is an emerging international high-risk clonal lineage. In addition to its MDR phenotype that mostly matched the genotype, PBIO3502 demonstrated pronounced virulence features, including in vitro biofilm formation, siderophore secretion, serum resilience, and in vivo mortality in Galleria mellonella larvae. Along with the genomic analysis indicating close phylogenetic relatedness of our strain with publicly available, clinically relevant representatives of the same ST, these results suggest the zoonotic and pathogenic character of PBIO3502 with the potential to cause infection in humans and animals. Also, our study highlights the necessity of the One Health approach while integrating human, animal, and environmental health, as well as the role of meat products and food chains in the putative transmission of MDR pathogens.

Combustion parameters are the important aspects in the development and research of an internal combustion engines. Hence present work is an attempt to develop an artificial neural network (ANN) model for anticipating the combustion characteristics of computerized CI DI VCR, four strokes, single cylinder, and water cooled engine using mixture of two biodiesel and diesel blends as a fuel. The two biodiesel selected are Jatropha and Simarouba and mixed in the ratio of 75:25. Two biodiesel mixtures is used for the preparation of various blends with diesel. Experiments are carried out at different compression ratio, at different % load and blends B20, B40, B60and neat diesel (B00) fuel to accumulate the assorted combustion data. The input variables are % load, compression ratio, blends and crank angle. The outputs well thought-out are cylinder pressure (CP), net heat release rate (NHRR), cumulative heat release (CHR), rate of pressure rise (RPR), mass fraction burned (MFB) and maximum cylinder pressure. The assessment is focused on developing artificial neural network for the prediction and verifying the combustion characteristics of engine. MATLAB software is used for analysis of different combustion aspects of the engine. Multilayer neural network perceptions are used with Feed-Forward Back Propagation algorithm with performance function for mapping the input and output parameters. The experimental outcomes are compared with ANN estimated results for the analysis. The outcome from the study authenticate that experimental results are in match with ANN results. The accuracy of the ANN model shows the developed model can effectively predict the engine combustion characteristics with excellent regression coefficients ‘R’ and its values are close to unity and the mean square errors are extremely less. ANN model approach is competent towards predicting the combustion aspect of diesel engine with good accuracy

Keywords: Requirements prioritization, Next release plan, Software product planning, Decision support, MoSCoW, AHP, K-Menas, GMM, BIRCH, PAM, Hierarchical, Clustering, Clusters Evaluation

This study investigates the emergence of ertapenem-resistant, meropenem-susceptible (ErMs) among non-carbapenemase producing (NCP) and carbapenemase producing (CP) Escherichia coli and Klebsiella pneumoniae. As mutations for ertapenem resistance establish the genetic background for non-carbapenemase meropenem resistance, there is a great need for antibiotic stewards and researchers to understand the determinants of a strain’s propensity to become resistant. Whole genome sequencing was conducted on clinical carbapenem-resistant E. coli (CREC) and K. pneumoniae (CRKP) across 5 hospitals in San Antonio, U.S. from 2012-2018. The majority of carbapenem resistant Enterobacterales (CRE) were NCP (54%; 41/76). The blaCTX-M was found to be most prevalent among NCP isolates (p = 0.02). LC-MS/MS analysis of carbapenem hydrolysis revealed that blaCTX-M-mediated carbapenem hydrolysis, indicating the need to reappraise the term, “non-carbapenemase (NCP)” for quantitatively uncharacterized CRE strains harboring blaCTX-M. Antimicrobial susceptibility results showed that 56% of all NCPE isolates had an ErMs phenotype (NCPE vs. CPE, p &lt; 0.001), with E. coli driving the phenotype (E. coli vs. K. pneumoniae, p &lt; 0.001). ErMs strains carrying blaCTX-M, had approximately 4-fold more copies of blaCTX-M than ceftriaxone-resistant but ertapenem and meropenem susceptible (EsMs) isolates (3.7 v. 0.9, p &lt; 0.001). ErMs also carried more mobile genetic elements (MGEs), particularly IS26 composite transposons, than EsMs (37 vs. 0.2, p &lt; 0.0001). Immunoblot analysis demonstrated the absence of OmpC expression in NCP-ErMs E. coli, with 92% of strains lacking full contig coverage of ompC. Overall, this work provides evidence of a collaborative effort between blaCTX-M and OmpC in NCP strains that confer resistance to ertapenem but not meropenem. To thwart potential mismanagement of CRE infected patients, future efforts should focus on understanding the mechanism(s) underlying OmpC loss, developing rapid methods to detect blaCTX-M copy number variants, and targeted antimicrobials for NCPE and ErMs strains.

In this paper, the new optical wave solutions of truncated M-fractional perturbed Kundu-Eckhaus model with full non-linearity are obtained by utilizing the expa function technique and modified extended tanh expansion function technique. The solutions are in the form of dark soliton, bright soliton, singular solitons and other form of solutions. The gained solutions are helpful for the further development of concerned model. The obtained results have also been presented graphically in both two-dimensional and three-dimensional formats to discuss the dynamical features as well as the parametric dependence of the constructed solutions. The study offers a highly spectacular and acceptable techniques to combine various intriguing wave demonstrations for more sophisticated models of the modern day.