Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

Adeno-associated viruses (AAVs) have been used for liver gene therapy. Hemgenix and Roctavian are AAV-based treatments for hemophilia B and A, respectively. They cost $3 million and $2.8 million per dose, respectively. While AAV vectors may eventually be cheaper to mass produce, a bacteria-based DNA delivery system might be much cheaper for patients. Also, “bactofection” would allow for the delivery of much larger DNA packages. Such a bacterial system may now be possible, and a prototype for the liver could possibly be developed immediately.

The production of municipal solid waste incineration bottom ash (MSWIBA) is very massive and has the potential to replace cement despite the problems of complex composition, uneven particle size distribution, and low reactivity. This paper adopts sodium silicate activation of MSWIBA-slag to improve the reactivity to prepare composite cementitious materials. It explores the hydration performance study of the composite cementitious materials by isothermal calorimetric analysis, Fourier Transform Infrared (FTIR) spectroscopy, XRD physical diffraction analysis, and SEM/EDS tests. SEM/EDS tests will be used to explore the hydration properties of the composite gelling. The results showed that with the increase of MSWIBA doping, the porosity between the materials increased, the degree of Hydration decreased, and the compressive strength decreased with the rise of MSWIBA. When sodium silicate increased from 25% to 35%, too much alkaline material occurred over the alkaline effect, which inhibited the Hydration of the particles, and the degree of hydration reaction decreased, and the compressive strength decreased accordingly; the exothermic process of Hydration can be mainly divided into five stages, quartz and calcite did not participate in the hydration reaction completely, and sexual aluminum participated in the hydration reaction. The vibrational peaks of Si-O-Ti (T = Si and Al) were present in the material. The vibrational peaks of XRD, FTIR, and SEM-EDS all indicate the presence of silica-aluminate network structures in the hydration products, mainly N-A-S-H and C-A-S-H gels.

Fiber-rich green river Aonori alga is mass-cultivated in Japan; it has been reported to reduce inflammation and improve metabolic health in humans. Peroxisome proliferation-activated receptor (PPARs) are associated with metabolic disorders such as obesity and type 2 diabetes (T2DM). We evaluated the effects of supplementation with NBF2, a formula made of algal and junos citrus biomaterials, on metabolic markers in obese and diabetic rats. An experimental study was performed using 18 obese and hyperglycemic Otsuka Long-Evans Tokushima Fatty (OLETF) rats randomly assigned to high dose NBF2 (20mg/kg; n=6), low dose (10mg/kg; n=6) NBF2 drink for 6 weeks, whereas OLETF control rats received similar amount of tap water (vehicle; n=6). LETO rats were used as normal controls (n=8). Biospecimens were taken for ELISA and real-time PCR. Both high dose and low dose NBF2 increased brown adipose tissue (BAT) mass and adiponectin (APN), improved insulin sensitivity, and significantly improved glycemic and lipid (TG, LDL-c) profiles in NBF2-supplemented OLETF rats after a 6-week supplementation with NBF2 (vs. OLETF controls), as well as LDL-c (p<0.05). During the glucose tolerance test (OGTT), both NBF2 groups and LETO rats had normal glycemia by 90-minute time-point (vs. OLETF controls; p<0.01). Furthermore, intake of NBF2 up-regulated PPARa/g-mRNA and Sirt2-mRNA gene expressions in BAT, and improved blood pressure profile in OLETF rats. Findings from this research suggest that intake of NBF2 formula induces dual PPAR-a/g and Sirt2 activation, providing insights on beneficial prophylactic and therapeutic effects of this NB2 formula on dyslipidemia and hyperglycemia in T2DM.

Cold plasma (CP) is an ionised gas containing excited molecules and ions, radicals, free electrons, and emits electric fields and UV radiation. CP is potently antimicrobial and can be applied safely to biological tissue, birthing the field of plasma medicine. Reactive oxygen and nitrogen species (RONS) produced by CP affect biological processes directly or indirectly via the modification of cellular lipids, proteins, DNA, and intracellular signalling pathways. CP can be applied at lower levels for oxidative eustress to activate cell proliferation, motility, migration, and antioxidant production in normal cells, mainly potentiated by the unfolded protein response, Nrf2-activated antioxidant response element and PI3K/Akt pathway, which also activates NFκB. At higher CP exposures, inactivation, apoptosis and autophagy of malignant cells can occur via degradation of PI3K/Akt and MAPK-dependent and -independent activation of the master tumour suppressor p53, leading to caspase-mediated cell death. These opposing responses validate a hormesis approach to plasma medicine. Clinical applications of CP are becoming increasingly realised in wound healing, while clinical effectiveness in tumours is currently coming to light. This review will outline advances in plasma medicine and compare the main redox and intracellular signalling responses to CP in wound healing and cancer.

Exposure to ionizing radiation, accidental or intentional, may lead to delayed effects of acute radiation exposure (DEARE) that manifest as injury to organ systems including kidney, heart, and brain. This study examines the role of activated protein C (APC), a known mitigator of radiation-induced early toxicity, in long-term plasma metabolite and lipid panels that may be associated with DEARE. Male and female cohorts of C57BL/6N wild-type and APCHi transgenic mice were exposed to 9.5 Gy γ-rays with their hind-legs shielded to allow long-term survival that is necessary to monitor DEARE, and plasma was collected at 6 months for LC-MS based metabolomics and lipidomics. We observed significant dyslipidemia, indicative of inflammatory phenotype, upon radiation exposure. Additionally, observance of several other metabolic dysregulations was suggestive of gut damage, perturbations in TCA and urea cycles, and arginine metabolism. We also observed gender and genotype modulated metabolic perturbations post radiation exposure. The APCHi mice showed near normal abundance for several lipids. Moreover, restoration of plasma levels of some metabolites including amino acids, citric acid, and hypoxanthine in APCHi mice are indicative of APC-mediated protection from radiation injuries. With the help of these findings the role of APC in plasma molecular events after acute -radiation exposure in a gender-specific manner can be established for the first time.

Electrochemical methods are used for the treatment of both municipal and industrial wastewater, either independently or in conjunction with biological methods. This conjunction is used for pretreatment or posttreatment of biologically treated wastewater. In our work, we focused on the combination of these processes, where pre-electrolysis was used to produce dissolved iron before the activation process. Electrolysis was also directly introduced into the activation using either iron or carbon electrodes. The surface of one iron electrode was 32.2 cm2, the applied voltage was 21 V, and the supplied current was 270 mA. The surface of one carbon electrode was 7.54 cm2, the supplied current was 82.5 mA, and the applied voltage was 21 V. From laboratory research on the treatment of synthetic municipal wastewater using a combination of electrolysis and activation processes, it resulted that the use of iron electrodes increased the efficiency of phosphorus removal compared to its precipitation with iron salts. The electrolysis had a positive effect on the sedimentation properties of sludge and the destruction of filamentous microorganisms. Electrolysis negatively affected the respiration rates of activated sludge and the efficiency of denitrification. However, it did not have a negative impact on the nitrification activity of the sludge.

A systematic study has been conducted on barbiturate complexes of all five alkali metals Li–Cs prepared from the metal carbonates or hydroxide in aqueous solution without other potential ligands present, varying the stoichiometric ratio of metal ion to barbituric acid (BAH). Eight polymeric compounds (two each for Na, K, and Rb and one each for Li and Cs) have been characterised by single-crystal X-ray diffraction. All contain some combination of barbiturate anion BA− (necessarily in a 1:1 ratio with the metal cation M+), barbituric acid, and water. All organic species and water molecules are coordinated to the metal centres via oxygen atoms as either terminal or bridging ligands. Coordination numbers range from 4 (for the Li complex) to 8 (for the Cs complex). Extensive hydrogen bonding plays a significant role in all the crystal structures, almost all of which include pairs of N–H…O hydrogen bonds linking BA− and/or BAH components into ribbons extending in one dimension. Factors influencing the structure adopted by each compound include cation size and reaction stoichiometry as well as hydrogen bonding.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Nanocomposites of TiO₂ Degussa P25 nanoparticles/activated carbon (TiO₂/AC ) were prepared at various mass ratios of (4:1), (3:2), (2:3), and (1:4) by a facile process. The effects of TiO₂/AC mass ratios on the structural, morphological, and photocatalytic properties were systematically studied in comparison with bare TiO₂ and bare AC. TiO₂ nanoparticles exhibited dominant anatase and minor rutile phases, and a crystallite size of approximately 21 nm; while AC had XRD peaks of graphite and carbon, and a crystallite size of 49 nm. The composites exhibited tight decoration of TiO₂ nanoparticles on micron-/submicron AC particles, and uniform TiO₂/AC composites were obtained as evidenced by the uniform distribution of Ti, O, and C in an EDS mapping. Moreover, Raman spectra show the typical vibration modes of anatase TiO₂ (e.g., E_1g⁽¹⁾, B_1g⁽¹⁾, E_g⁽³⁾) and carbon materials with D and G bands. The TiO₂/AC with (4:1), (3:2), and (2:3) possessed higher reaction rate constants (k) in photocatalytic degradation of methylene blue (MB) than that of either TiO₂ or AC. Among the investigated materials, TiO₂/AC = 4:1 achieved the highest photocatalytic activity with a high k of 55.2×10^-3 min^-1 and an MB removal efficiency of 96.6% after 30 min treatment under UV-Vis irradiation (120 mW/cm²). The enhanced photocatalytic activity for TiO₂/AC is due to the synergistic effect of the high adsorption capability of AC and the high photocatalytic activity of TiO₂. Furthermore, TiO₂/AC promotes the separation of photoexcited electron/hole (e^-/h⁺) pairs to reduce their recombination rate and thus enhance photocatalytic activity. The optimal TiO₂/AC composite in this study can be used for treating industrial or household wastewater with organic pollutants.

Sleep fragmentation (SF) can increase inflammation and production of reactive oxygen species (ROS), leading to metabolic dysfunction. SF is associated with inflammation of adipose tissue and insulin resistance. Several studies suggested that melatonin may have beneficial metabolic effects by activating AMP-activated protein kinase (AMPK). However, it is unclear whether melatonin affects the AMPK signaling pathway in SF-induced metabolic dysfunction. Therefore, we hypothesize that SF induces metabolic impairment and inflammation in white adipose tissue (WAT), as well as altered intracellular homeostasis. We further hypothesize that these conditions could be improved by melatonin treatment. We conducted an experiment using adult male C57BL/6 mice, which were divided into three groups: control, SF, and SF with melatonin treatment (SF+Mel). The SF mice were housed in SF chambers, while the SF+Mel mice received daily oral melatonin. After 12 weeks, glucose tolerance test, insulin tolerance test, adipose tissue inflammation, and AMPK assessments were performed. The SF mice showed increased weight gain, impaired glucose regulation, inflammation, and decreased AMPK in WAT compared to the controls. Melatonin significantly improved these outcomes by mitigating SF-induced metabolic dysfunction, inflammation, and AMPK downregulation in adipose tissue. The therapeutic efficacy of melatonin against cardiometabolic impairments in SF may be due to its ability to restore adipose tissue homeostatic pathways.

Heel pain in the “funnel-shaped” space between the calcaneus, talus, and talocalcaneonavicular and subtalar joints may be representative of Sinus Tarsi syndrome. The pain is often characterized by a burning, numbness, or tingling sensation that can stem from strains and tears on the ligaments in that area. Injury treatment typically includes balance training, muscle exercises, bracing, foot orthosis, and non-steroidal anti-inflammatory drugs (NSAIDs). This study presents Wharton Jelly (WJ) tissue allografts as an alternative intervention for patients who fail standard-care treatments. WJ targets tissue defects, unlike other therapies, which aim to reduce swelling and symptomatic pain. This study includes five female patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. After an average of 80 days, the cohort had an overall 85.29% improvement in pain. The study's limitations include a small cohort size and a non-blinded design. Given the significant improvement in pain, WJ tissue allograft, combined with other techniques, presents an optimal patient care plan for tissue defects associated with Sinus Tarsi syndrome when standard-of-care treatments fail. These results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

Continuous cropping of Platycodon produces problems that significantly impact its yield and quality making it a pressing issue that requires immediate attention. In this study, the sandwich method is employed to evaluate the allelopathic activity of different plant parts (leaves, stems, and roots) of Platycodon. The inhibitory effects of the various Platycodon plant parts were quantified based on their effects on lettuce seedlings growth by Sandwich method, with the following average inhibition percentages at 1 mg/ml (agar) of : leaves (79.4%, 61.8%), stems (58.0%, 45.7%), and roots (53.4%, 49.3%) for lettuce radicals and hypocotyls, respectively. At a concentration of 5 mg/ml, the inhibitory effects were as follow: leaves (91.9%, 72.2%), stems (79.5%, 60.3%), and roots (71.4%, 65.2%). Also, by employing the Plant Box method, it was determined that Platycodon root exudation. The growth inhibition rates of lettuce seedling roots and hypocotyls were 45.5% and 18.9%, respectively. The effect of activated carbon on the adsorption of allelopathic substances was investigated, and the results of the sandwich method with a concentration of 1 mg/ml showed the following growth inhibitory effects on lettuce seedlings and hypocotyls: roots (27.8%, 25.7%), leaves (13.3%, 25.7%), and stem (9.07%, 13.6%). The Plant Box method revealed average rates of inhibition of -16.7% and -4.70% on the growth of lettuce seedlings and hypocotyls, respectively. The results of this study demonstrated that activated carbon has a mitigating effect on the allelopathic inhibition associated with the different plant parts and root exudation of Platycodon, thus may provide a potential solution for overcoming obstacles associated with continuous cropping of Platycodon.

Caused by pathogenic microorganisms, such as bacteria, parasites, fungi, among others, infectious diseases can spread directly or from one individual to another. According to the World Health Organization, these diseases are known to cause high mortality rates, severe burdens of disability and serious worldwide aftermaths. The inappropriate use of antibiotics in humans are the main origins of the development of drug-resistant pathogens, which reduce the efficacy of these therapies, thus accentuating the need to search for effective antimicrobials. Medicinal plants have served as starting material for the preparation of a number of antimicrobial agents. To this end, the present study highlights the green synthesis of Cocos nucifera-based nanomaterials and evaluation of the mechanistic basis of their antimicrobial action. Accordingly, Cocos nucifera extract was used to reduce different concentrations (5, 10 and 20 mM) of silver nitrate solution to afford silver nanoparticles (AgNPs). These entities were further incorporated onto activated carbons (obtained by chemical activation using sulphuric acid as activation agent) to generate the nanocomposites. The antimicrobial activity of the as-prepared nanomaterials was evaluated using the broth microdilution method, while, the antioxidant activity was assessed through standard methods, such as 2,2-diphenyl-1-picrylhydrazyl (DPPH), and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid (ABTS) assays. Cytotoxicity of potent nanomaterials was assessed on Vero cells by spectrophotometric method. As a result, nanoparticles were successfully synthesized as evidenced by the color change of the solution from transparent to dark brown. Further characterization was carried out by UV-visible spectroscopy that showed an intense absorption spectrum at 433 nm. Fourier Transform Infrared Spectroscopy (FTIR) revealed the functional group moieties involved as a capping and reducing agent in the synthesis of AgNPs. The incubation of nanomaterials with selected bacterial and fungal strains led to significant inhibitory effects of these pathogens with minimum inhibitory concentrations ranging from 7.813 to 250 μg/ml. In antioxidant assays, the nanocomposites presented scavenging activities comparable to that of ascorbic acid. Cytotoxicity experiment revealed no toxic effects on the human mammalian cells Vero (range of selectivity indices: from &gt;4 to &gt;128). These results provide evidence of the implication of Cocos nucifera-based nanomaterials in targeting bacterial or fungal systems that mediate free-radical damage or by inhibiting the oxidative damage caused by selected bacteria and fungi, the most susceptible being Escherichia coli and Candida albicans, respectively.

Disulfiram (DSF), an anti-alcoholism medicine, exerts treatment effects in patients suffering from persistent Borreliosis and also exhibits anti-cancer effects by its copper chelating derivatives. Since chronic/persistent borreliosis is characterized by increased amounts of proinflammatory macrophages, this study investigated opsonin-independent phagocytosis, migration and surface marker expression of in vivo activated human monocyte-derived macrophages and dendritic cells with and without DSF treatment. Phagocytosis of non-opsonized Dynabeads® M-450 and migration of macrophages and dendritic cells were monitored using live cell analyzer Juli™ Br for 24h by imaging every 3.5 min. Results were analyzed by a newly developed software based on the differential phase contrast images of cells before and after ingestion of Dynabeads bearing an electron dense iron core. As a control, phagocytosis was also monitored by visual counting of ingested beads. DSF decreased the phagocytic capacities exhibited by global macrophages and dendritic cells. DSF also impaired the migration of human monocyte-derived macrophages and dendritic cells (hMDMD) and significantly reduced the expression densities of surface antigens CD45 and CD14. In cells consisting of anti-inflammatory M2 macrophages, DSF led to a remarkable cell death and also increased oxidative stress as determined by MitoSox staining. Mitochondrial oxidative stress was a prominent feature in M2 macrophages which were more sensitive to DSF-induced cytotoxicity.

The rapid development of electric vehicles, unmanned aerial vehicles, and wearable electronic devices has led to a high interest in research related to the synthesis of graphene with a high specific surface area for energy applications. However, the problem of graphene synthesis scalability, as well as the lengthy duration and high energy intensity of the activation processes of carbon materials, are significant disadvantages. In this study, a reactor was developed for the green, simple, and scalable electrochemical synthesis of graphene oxide with a low oxygen content of 14.1 %. The resulting material was activated using a fast joule heating method. The processing of mildly oxidized graphene with a high–energy short electrical pulse (32 ms) made it possible to obtain a graphene–based porous carbon material with a specific surface area of up to 1984.5 m2/g. The low energy intensity, simplicity, and use of environmentally friendly chemicals render the proposed method scalable.

The studied Khanbogd pluton of peralkaline granite is located in southern Mongolia and occupies an area of ~1000 sq. km. Previously, two ring-shaped bodies were constructed in a flattened shape pluton. However, this shape was not used for the genesis of this pluton. A recent study of Landsat image showed a several elliptical intrusions in two bodies. Chemistry interpretation shows that each intrusion differs in ASI, CIPW norms, 87Sr/86Sri and δ18O isotopes. Elliptical intrusions, uplifted country rocks between them, and roof pendants suggest magma penetration along fractured country rocks. Furthermore, two adjacent intrusive bodies and undeformed host rocks at the front part of the pluton are consistent with underplating magmatic factors during duplex-type thrusting. This magma event is also supported by low of Sr, Ba, Eu and high of Th, U, Pb anomalies and a few amount of garnet crystals in the granites, implying vapor absent melt crystallization associated with underplating. Multiple melt sources, as well as from mantle and recycled sea floor rocks, are identified by ratio of 87Sr /86Sri and δ18O values. The low isotope values, the thrust nature and 295–286 Ma ages of the alkali granites, indicate an underplate magma evidenced during Permian rifting.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

Serine proteases regulate cell functions through G protein-coupled protease-activated receptors (PARs). Cleavage of one peptide bond of the receptor amino terminus results in the formation of a new N-terminus ("tethered ligand") that can specifically interact with the second extracellular loop of the PAR receptor and activate it. Activation of PAR1 by thrombin (canonical agonist) and activated protein C (APC, noncanonical agonist) was described as biased agonism. Here we have supposed that synthetic peptide analogues to the PAR1 tethered ligand liberated by APC could have neuroprotective effects like APC. To verify this hypothesis a model of the ischemic brain impairment based on glutamate (Glu) excitotoxicity in primary neuronal cultures of neonatal rats has been used. It was shown that nanopeptide NPNDKYEPF-NH2 (AP9) effectively reduced the neuronal death induced by Glu. The influence of AP9 on cell survival was comparable to that of APC. Both APC and AP9 reduced the dysregulation of intracellular calcium homeostasis in cultured neurons induced by excitotoxic Glu (100 µM) or NMDA (200 µM) concentrations. PAR1 agonist synthetic peptides might be a noncanonial PAR1-agonist and a basis of novel neuroprotective drugs for disorders related to Glu excitotoxicity such as brain ischemia, trauma and some neurodegenerative diseases.

The rapid and accurate detection of parasites is crucial for timely curative intervention in parasitosis and for epidemiological surveillance. To meet the needs of clinical diagnosis, it is imperative to develop a diagnostic tool based on nucleic acid that combines the sensitivity and specificity of established nucleic acid amplifica-tion tests with the speed, cost-effectiveness, and convenience of isothermal amplification methods. A new nu-cleic acid detection method, utilizing the clustered regularly interspaced short palindromic repeats (CRISPR)-associated (Cas) nuclease, holds promise for point-of-care testing. Specifically, the CRISPR-Cas12a system has demonstrated numerous advantages for detecting parasites, with hopeful outcomes for identify-ing malaria, toxoplasmosis, and other parasitic ailments. This review provides an overview of how CRISPR-Cas12a can be utilized for parasite detection, evaluates its advantages and disadvantages, and sug-gests ways to improve the efficiency and sensitivity of CRISPR-Cas12a-based assays.

Background: We previously reported that human keratinocytes express protease-activated receptor (PAR)-2 and play an important role in activated protein C (APC)-induced cutaneous wound healing. This study investigated the involvement of PAR-2 in the production of gelatinolytic matrix metalloproteinases (MMP)-2 and -9 by APC during cutaneous wound healing. Methods: Full-thickness excisional wounds were made on the dorsum of male C57BL/6 mice. Wounds were treated with APC on days 1, 2, and 3 post-wounding. Cultured neonatal foreskin keratinocytes were treated with APC with or without intact PAR-2 signalling to examine the effects on MMP-2 and MMP-9 production. Murine dermal fibroblasts from PAR2 knock-out (KO) mice were also assessed. MMP-2 and -9 were measured by gelatin zymography, fluorometric assay, and immunohistochemistry. Results: APC accelerated wound healing in WT mice, but had negligible effect in PAR-2 KO mice. APC stimulated murine cutaneous wound healing was associated with differential 0temporal production of MMP-2 and MMP-9, with the latter peaking on Day 1 and the former on Day 6. In-hibition of PAR-2 in human keratinocytes reduced APC-induced MMP-2 activity 25~50, but had little effect on MMP-9. Similarly, APC-induced MMP-2 activation was reduced by 40% in cultured dermal fibroblasts derived from PAR-2 KO mice. Conclusion: This study shows for the first time that PAR-2 is essential for APC-induced MMP-2 production. Considering the important role of MMP-2 in wound healing, this work helps explain the underlying mechanisms of action of APC to promote wound healing through PAR2.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

Eruca sativa is a commonly used edible plant in Italian cuisine. E. sativa 70% ethanol extract (ES) was fractionated with five organic solvents. Ethyl acetate fraction(EEA) had the highest antioxidant activity, which was correlated with the total polyphenol and flavonoid content. ES and EEA acted as PPAR-α ligands by PPAR-α competitive binding assay. EEA significantly increased cornified envelope formation as a keratinocyte terminal differentiation marker in HaCaT cells. Further, it significantly reduced nitric oxide and pro-inflammatory cytokines in lipopolysaccharide-stimulated RAW 264.7 cells. The main flavonol forms detected in high amounts from EEA are mono-, and di-glycoside of each aglycone. Flavonol mono-glycosides were shown to be a potent PPAR-α ligand using molecular docking simulation and showed the inhibition of nitric oxide. These results suggest that E. sativa is suitable for use in improving skin barrier function and inflammation in skin disorders, such as atopic dermatitis.

Flexible energy storage devices, such as solid-state supercapacitors, are becoming increasingly attractive due to their characteristics of high electrochemical performance, reliability, light weight, flexibility, absence of electrolyte leakage, high power density, and long lifetime. For the optimization of the solid-state symmetrical supercapacitor proposed in this work, it was employed in sodium and lithium form Aquivion electrolyte membrane, which serves as the separator and electrolyte. As electrode materials, carbon xerogels, synthesized by microwave-assisted sol-gel methodology, with designed and controlled properties were obtained. Commercial activated carbon (YP-50F, 'Kuraray Europe' GmbH) was used for comparison. Specifically, the developed solid-state symmetrical supercapacitors deliver sufficient high specific capacitances of 105−110 F g−1 at 0.2 A g−1, along with an energy density of 4.5 Wh kg−1 at 300 W kg−1, and in a voltage window of 0-1.2 V in an aqueous environments, also demonstrating excellent cycling stability up to 10,000 charge/discharge cycles. These results can demonstrate the potential applications of carbon xerogel as an active electrode material and cation exchange membrane as the electrolyte in the development of solid-state supercapacitor devices

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

Smoked cigarette butts (SCB) can be used as precursors to obtain activated carbon (AC) due to their high carbon content related to the presence of cellulose acetate and components that are retained in the tobacco combustion process. In this way, it was analyzed how the process of pyrolysis or formation of char from this residue occurs, for this a study of the kinetics of formation of char is carried out by thermogravimetry, using three heating speeds 5, 10 and 15 °C/min. Based on the data obtained, mathematical models such as Kissenger - Akahira - Sunose (KAS), Starink (STK) and Ozawa - Flynn - Wall (OFW) were used in order to identify thermodynamic parameters through the energy of activation. The char obtained was subjected to an activation treatment with KOH in order to increase the surface area and pore volume, obtaining values of 433 m2/g of BET area and 0.25 cm3/g of micropore volume. Finally, the adsorbent was applied in the removal of Cr (VI) obtaining a Qmax capacity determined by the Langmuir model of 55.8 mg/g.

Alkali-activated materials, sometimes called geopolymers, can be used as alternative cementitious materials to conventional Portland cement. There is a significant current interest in these materials due to their low CO2 footprint. Typical applications of alkali-activated materials are within civil engineering, however, potential applications as well cementing material within oil & gas are also being studied with emerging interest. This paper presents a systematic study of compressive strength development from 1 to 28 days for metakaolin-based alkali-activated cement. The results show that compressive strength is highly dependent upon the initial Si/Al ratio in the mix design, as well as the concentration of the activator solution. Furthermore, due to the relatively low initial reactivity of the used metakaolin material, different types of co-binders were included in the slurry composition to improve early strength development. The two different co-binders tested were another, more reactive metakaolin material and Blast Furnace Slag (GGBFS). It was found that both these co-binders performed as intended, by ensuring early strength development via precipitation of K-A-S-H and C-A-S-H gels, respectively, and also by enabling subsequent strength development due to improved dissolution of the low-reactive metakaolin.

Increased volume of untreated and inadequately treated municipal wastewater undermines the circular economy potential of wastewater resources, particularly in low-income region. This present study focused on and evaluated the performance of native microalgae-activated sludge (MAS) growth for tertiary treatment of anaerobically digested wastewater from an upflow anaerobic sludge blanket (UASB) in an outdoor lab-scale photobioreactors (2 L). Seven conditions with distinct inoculum concentrations were operated in batch mode in triplicate for 5-days hydraulic retention time (HRT) at 11.5:12.5 Photo-hours. MAS inoculum concentration influenced treatment outcome. The best performance was observed in MAS concentration 0.10/0.20 g L-1, with cell density count (2.03 x 107 cells mL-1), biomass productivity 0.125 g TSS L-1 d-1 and total phosphorus uptake (85.07%), total nitrogen uptake (66.14%). Logarithmic removal (Log-Re) of bacterial pathogens (water quality indicators) showed Log-Re ((3.4 for total coliforms (1.37E+02 CFU 100 mL-1) and 4.7 for Escherichia coli (0.00E+00 CFU 100 mL-1)). Results revealed optimum remediation performance and nutrients’ recovery potential with appropriate inoculum concentration, in admiration to advancing the science of circular economy.

Perilla frutense var. acuta (Lamiaceae) has been used to treat indigestion, asthma, and allergies in traditional medicine. In this study, luteolin 7-O-diglucuronide (1), apigenin 7-O-diglucuronide (2), and rosmarinic acid (3) were isolated from the leaves of P. frutescens var. acuta. Various approaches were performed to investigate the anti-inflammatory activity of the isolated compounds (1-3) and their working mechanisms. In silico docking simulation demonstrated that 1-3 would work as a PPAR-α/δ/γ agonist, and in vitro PPAR-α/δ/γ transcriptional assay showed that the Perilla extract and 3 increased PPAR-α luciferase activity [1.71 and 1.61 times of the control (PPAR-α + PPRE, p < 0.001)]. In the NF-κB luciferase assay, 1 suppressed NF-κB activity the most (56.83 % at 5 µM; 74.96 % at 10 µM; 79.86 % at 50 µM). In addition, 1 and 2 inhibited the mRNA expression of NF-κB target genes, including Il6, Mcp1, and Tnfa, at 50 µM, and 3 suppressed the genes at the mRNA level in a dose-dependent manner. We report that 1 and 2 exert anti-inflammatory effects through NF-κB inhibition, and PPAR-α/NF-κB signaling pathway is related to the anti-inflammatory activity of 3.

This study examines the impact of the impregnation of fireclay-based conventional (CC) and medium cement castables (MCC) with liquid sodium silicate glass under vacuum conditions. The goal is to assess how this treatment affects physical, mechanical properties, and durability (alkali and thermal shock resistance) of these castables used in biomass combustion boilers, where they are exposed to temperatures up to 1100°C. The research work employs standard test methods to evaluate physical and mechanical properties. Additionally, advanced techniques such as scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and specific tests for alkali resistance and thermal shock resistance are used. The research findings suggest that impregnation with sodium silicate glass under vacuum significantly enhances the alkali resistance of both CC and MCC castables. This improvement is primarily due to the reduction in porosity and the increase in density. SEM images reveal that impregnated samples are coated with a glassy layer and the pores are partially filled with sodium silicate. Tests for alkali resistance demonstrate the formation of a protective glassy layer (with a thickness of 0.9-1.5 mm) on the castables surfaces, thereby reducing further penetration of alkali into deeper layers of the samples. However, it is important to mention that impregnated refractory castables have reduced resistance to thermal shock cycles.

In this study, Plasma-Activated Water (PAW) was synthesized using a coaxial Dielectric Barrier Discharge (DBD) reactor, benefiting from the elevated capacity of air-flow-assisted DBD discharges to enhance nitrogen-based species concentration. By manipulating operational parameters, including gas flow rate, activation time, and DI water volume, we achieved significant concentrations of Reactive Oxygen and Nitrogen Species (RONS). As a result, the PAW obtained displayed pronounced physicochemical attributes: a pH of 2.06, an ORP of 275mV, conductivity of 3mS/cm, and TDS of 1200 mg/L. A pivotal aspect of this research was the evaluation of the reactor's efficiency, as indicated by metrics like the specific input energy and ozone efficiency yield. The antimicrobial potential of the PAW was also assessed against pathogenic microbes, with remarkable reductions in viability for both Staphylococcus aureus and Escherichia coli (99.99%) and a more moderate decrease for Candida albicans (37%). These findings underscore the capability of the coaxial DBD reactor in crafting high-quality PAW with significant antimicrobial properties, necessitating further studies to validate its broad-spectrum and safe application.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

Studying the distribution and transport dynamics of cations in plants is crucial for understanding their response mechanisms to saline-alkali stress conditions. However, our current understanding of how restoration measures affect cation distribution and transport in plants is surprisingly limited. To address this gap, we conducted a split-plot experiment using Medicago sativa L. cv. “Zhongmu No. 1” to investigate the combined effects of biological and chemical restoration measures—with bio-fertilizer as the primary zone and flue gas desulfurization (FGD) gypsum with humic acid as the secondary zone—on soil properties, plant growth, and the content, distribution, and transport of cations in plants. The results revealed that different restoration strategies decreased soil alkalinity and enhanced plant growth. Significantly, bio-fertilizer exhibited positive effects on plant growth and yield. On the contrary, FGD gypsum with humic acid reduced the soil's pH level, exchangeable sodium percentage, and sodium adsorption ratio, while increasing the contents of K+, Ca2+, and Mg2+ in the soil. The triple combination of FGD gypsum and humic acid with bio-fertilizer reduced Na+ transport in M. sativa by enhancing the selective absorption of beneficial ions, such as K+, Ca2+, and Mg2+ in leaves, and by facilitating the transport of Ca2+ and Mg2+ from roots and stems to the leaves. Therefore, the application of FGD gypsum and humic acid combined with bio-fertilizer has the potential to decrease soil alkalinity and the proportions of water-soluble ions in the soil, ultimately enhancing the translocation of key ionic components to leaves. This, in turn, increases the salt tolerance of plants and promotes their growth. Our results offer new insights into the interactions among measures, soil, and plants in saline-alkali land restoration, providing practical solutions for the restoration of saline-alkali soil.

This study aimed to elucidate the antibacterial efficacy and unique chemical compositions generated from plasma-activated water (PAW) when utilized a novel vaginal cleansing device. We conducted an analysis of antibacterial activity against probiotics and several chemical compositions including ions under various operational parameters of PAW, including electrical power (12 and 24 V), treatment duration (1, 10, and 20 min), and stay duration (immediate, 30 and 60 min). Our findings revealed that as treatment duration increased, hypochlorous acid (HOCl), Ca2+, and Mg2+ concentrations increased and Cl−concentrations decreased. Higher electrical power and longer treatment duration resulted in increased HOCl levels, which acts to prevent the growth of general microorganisms. Notably, PAW exhibited no antibacterial effects against a type of probiotic, Lactobacillus reuteri that produces lactic acid for vaginal health. This result demonstrated the ability of the vaginal cleaning device to generate ions, primarily HOCl and some cations (Ca2+ and Mg2+), thereby providing vaginal mucosa protecting and cleansing effects with the vaginal environment.

Repeated cocaine produces an enhanced locomotor response (sensitization) paralleled by biological adaptations in the brain. Previous studies demonstrated region-specific responsiv-ity of adenosine monophosphate-activated protein kinase (AMPK) to repeated cocaine. AMPK maintains cellular energy homeostasis at the organismal and cellular level. Here we first quanti-fied changes in phosphorylated (active) and total AMPK in the cytosol and synaptosome of the medial prefrontal cortex, nucleus accumbens, and dorsal striatum following acute or sensitizing cocaine injections. Rats were given cocaine (15 mg/kg, IP) or saline for six days with a challenge injection on day seven resulting in four groups: saline-saline, saline-cocaine, cocaine-saline, and cocaine-cocaine. Brain region and cellular compartment selective changes in AMPK and pAMPK were found with some differences associated with acute withdrawal versus ongoing cocaine treatment. Other rats were pretreated with the indirect AMPK activator metformin. Metformin potentiated the locomotor activating effects of acute cocaine but blocked the development of sensi-tization. Sex differences largely obscured protein level treatment group effects, although pAMPK in the NAc shell cytosol was surprisingly reduced by metformin in rats receiving repeated co-caine. These data inform our understanding of AMPK activation dynamics in subcellular com-partments and provide additional support for repurposing metformin for cocaine use disorder.

In this study, we report the antibacterial mechanisms of action of uniform silver nanoparticles (AgNPs) and decorated activated carbon nanocomposite (CAC-AgNPs) obtained using a green synthesis approach. The nanomaterials were characterized by ultraviolet-visible (UV-vis) absorption spectra and Fourier transform infrared (FTIR) spectra. The antibacterial activity of the as-prepared nanomaterials was evaluated against an array of bacterial strains by microdilution method, whereas their cytotoxicity profile was evaluated on Vero cells (human mammalian cells). The antibacterial mechanistic studies of active nanomaterials were carried out through bacterial growth kinetics, nucleic acid leakage test, and catalase inhibition assay. A silver nanocomposite was successfully fabricated from Croton macrostachyus-based activated carbon. The as-prepared nanomaterials exhibited antibacterial activity against an array of bacterial strains (minimum inhibitory concentration (MIC) range: 62.5 to 500 µg/mL), the most susceptible being Escherichia coli and Staphylococcus aureus. Cytotoxicity studies of the nanomaterials on Vero cells revealed that the nanocomposite (median cytotoxic concentration (CC50): 213.6 µg/mL) was less toxic than the nanoparticles (CC50 value: 164.75 µg/mL) counterpart. Antibacterial mechanistic studies unveiled that the nanomaterials induced (i) bacteriostatic activity vis-à-vis E. coli and S. aureus and (ii) inhibition of catalase in these bacteria. This novel contribution on the antibacterial mechanisms of action of silver nanocomposite from C. macrostachyus-based activated carbon might contribute to the understanding of antibacterial action of these biomaterials. Nevertheless, more chemistry and in vivo experiments, as well as in depth antibacterial mechanistic studies are warranted for the successful utilization of these antibacterial biomaterials.

The rhizome of Drynaria fortunei (Kunze ex Mett.) J. Sm., which is known as “Golsebo” in Korea, has been traditionally used to treat various inflammatory conditions, including bone metabolism disorders. It relieves blood extravasation, stops bleeding, repairs broken bone tissue, treats bone fractures, and kills bacteria. Recently, D. fortunei-derived polysaccharides (DFP) have been identified as bioactive compounds that act against numerous human diseases. However, the molecular mechanism underlying the bone metabolism-improving effect of DFP has not been elucidated. In this study, we evaluated the modulatory effects of DFP on the differentiation of bone marrow-derived macrophages into osteoclasts. We performed tartrate-resistant acid phosphatase assays using DFP (different concentrations and molecular weights) to evaluate the degree of bone resorption in the receptor activator of nuclear factor-κB ligand (RANKL)-induced osteoclastogenesis of bone marrow-derived macrophages. DFP significantly inhibited RANKL-induced osteoclastogenesis and suppressed RANKL-mediated overexpression of c-Fos and nuclear factor of activated T cells 1, thereby downregulating osteoclast-specific gene (Atp6v0d2, DC-STAMP, and cathepsin K) expression. DFP has potential as a nutraceutical candidate for treating bone loss diseases, including osteoporosis in postmenopausal women.

This study deals with the computational analysis of the kinetic processes of a microbial electrolysis cell assisted-anaerobic digestion (MEC-AD) treating raw-waste activated sludge (WAS), comparatively with a conventional AD, as well as the effect of the Organic Loading Rate (OLR) on the system’s performance. The aim was to derive a single kinetic and mathematical model for the study of the MEC-AD, using the ADM1 framework, which can be utilized to extract the effect of an applied potential on the kinetics of AD. The experimental data were obtained from the long-term, continuous operation of two identical reactors (an AD and a MEC-AD), which were operated at different OLRs (1.1, 1.7 and 2.9 gCOD/(L*d)). The results showed that the MEC-AD yielded improved biomass yields, substrate consumption kinetics and 1st order disintegration kinetics, with a predominant contribution to disintegration of complex particulates, comparatively with the AD. Moreover, it enabled operation at higher OLRs (achieving the highest divergence from the AD at the OLR of 4.14 gCOD/(L*d)), therefore accelerating sludge treatment, as well as an improved performance at an increased solids retention time (SRT). These findings can serve as a quantitative guide for the effects of the operating parameters on the raw-WAS-fed MEC-AD performance.

Sirtuins, especially SIRT1, play a significant role in the regulation of inflammatory response, autophagy, and cell response to oxidative stress. Since their discovery, sirtuins have been regarded as anti-aging and longevity-promoting enzymes. Sirtuin-regulated processes seem to take part in most prevalent placental pathologies, such as preeclampsia. Furthermore, more and more research studies indicate that SIRT1 may prevent pre-eclampsia development, or at least alleviate its manifestations. Having taken this into consideration, we have made a review of recent studies on the role of sirtuins, especially SIRT1, in the regulation of processes determining normal or abnormal development and functioning of the placenta.

Polymers' controlled pyrolysis is an economical and environmentally friendly solution to prepare activated carbon. However, due to the experimental difficulty in measuring the dependence between tissues and pyrolysis parameters at high temperatures, the unknown pyrolysis mechanism hinders access to the target products with desirable morphologies and performances. In this study, we investigate the pyrolysis process of polystyrene under different heating rates and temperatures employing reactive molecular dynamics (ReaxFF-MD) simulations. A clear profile of the generation of pyrolysis products determined by the temperature and heating rate is constructed. It is found that the heating rate affects the type and amount of pyrolysis intermediates and their timing, and low-rate heating helps yield more diverse pyrolysis intermediates. While the temperature affects the pyrolytic tissues of the final equilibrium products, either too low or too high a target temperature is detrimental to generating large areas of graphitized tissue. The established theoretical evolution process matches experiments well, thus contributing to preparing target activated carbons by referring to the regulatory mechanism of pyrolytic tissues.

Biomass exploitation is a global trend due to the circular economy and the environmentally friendly spirit. Numerous applications are now based on the use of biomass derived products. Hydrogen sulfide (H2S) is a highly toxic and environmentally hazardous gas, which emitted from various processes. Thus, the efficient removal of this toxic hazardous gas following cost effective processes is an essential requirement. In this study, we present the synthesis and characterization of biomass-derived activated-carbon/zinc-oxide (ZnO@AC) composites from different biomass sources as potential candidates for H2S sorption. The synthesis involved a facile method for activated carbon production via pyrolysis and chemical activation of biomass precursors (spent coffee, Aloe-Vera waste leaves, and corncob). Activated carbon production was followed by the incorporation of zinc oxide nanoparticles into the porous carbon matrix using a simple melt impregnation method. The synthesized ZnO@AC composites were characterized using X-ray diffraction (XRD), infrared spectroscopy (IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and nitrogen porosimetry. The H2S removal performance of the ZnO@AC composites was evaluated through sorption experiments using a handmade apparatus. Our findings demonstrate that the Aloe-Vera, Spent-coffee, and Corncob derived composites exhibit superior H2S sorption capacity up to 106 mgH2S/gads., 66 mgH2S/gads., and 47 mgH2S/gads. respectively.

Water pollution, driven largely by the discharge of organic dyes from various industrial processes, presents a grave environmental threat. This study delves into the promise of an innovative adsorptive composite material composed of chitosan and activated charcoal, offering a sustainable and efficient solution for removing methylene blue (MB) dye from water sources. Our comprehensive investigation encompasses the synthesis, characterization, and adsorption capabilities of this composite material, revealing its remarkable physicochemical attributes and its substantial capacity to adsorb MB dye. These findings establish it as a compelling candidate for water treatment applications. The assessment of adsorbent dosage shows a direct correlation between higher dosages and enhanced MB dye removal, with an optimal dosage determined at 0.4 g/25 mL. Furthermore, pH-dependent studies demonstrate exceptional performance at lower pH levels, achieving an impressive 95% removal rate at pH 3 after 240 minutes of contact time. The composite exhibits consistent high removal percentages across a wide range of MB dye concentrations, showcasing its adaptability. In terms of reaction time, the composite achieves peak adsorption capacity within the initial 360 minutes and maintains a stable equilibrium, sustaining an impressive 99% removal efficiency thereafter. This study underscores the eco-friendliness and cost-effectiveness of the composite material, emphasizing its potential to address water pollution challenges and promote sustainable water resource management. Overall, this research yields valuable insights into a practical approach for mitigating the adverse impact of organic dyes on aquatic ecosystems and public health.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

Nowadays the preservation and restoration of historical building needs to be faced in accordance with a novel sensibility regarding environment to preserve the future generations. In this context, the scientific community is focusing on novel and sustainable materials and techniques allowing durability and mechanical performances and at the same time compatibility with the existing heritage. Alkali activated materials represent a great challenge to produce new materials starting from the existing ones with reducing consumption, emission of greenhouse gases and environmental impact. This study deals with the valorization of waste materials coming from demolition and construction activities in the manufacture of geocomposites suitable for restoration and conservation of historical heritage. In particular, waste from tuff sawing and brick grinding were used as raw materials, then the geopolymeric samples produced were characterized from physical-chemical and mechanical point of view in order to investigate their performance and evaluate their suitability as materials for historical buildings recovery. Brick waste based geocomposites resulted to be more compact than the tuff-based ones as showed by the higher density values and the lower values of open porosity and water absorption and as further confirmed by the trend of the mechanical performance. Moreover, experimental data showed that physical and mechanical properties of both bricks and tuff waste-based geocomposites, even with different waste content, are compatible with existing building materials and to all the traditional repairing products.

Nuclear receptors (NRs) constitute a superfamily of ligand-activated transcription factors with a paramount role in ubiquitous physiological functions such as metabolism, growth, and reproduction. Owing to their physiological role and druggability, NRs are deemed attractive and valid targets for medicinal chemists. Pentacyclic triterpenes (PTs) represent one of the most important phytochemical classes present in higher plants, where oleanolic acid (OA) is the most studied PTs representative owing to its multitude of biological activities against cancer, inflammation, diabetes, and liver injury. PTs possess a lipophilic skeleton that imitates the NRs endogenous ligands. Herein, we report a literature overview on the modulation of metabolic NRs by OA and its semi-synthetic derivatives, highlighting their health benefits and potential therapeutic applications. Indeed, OA exhibited varying pharmacological effects on FXR, PPAR, LXR, RXR, PXR, and ROR in a tissue-specific manner. Owing to those NRs modulation, OA exhibited prominent hepatoprotective properties comparable to ursodeoxycholic acid (UDCA) in a bile duct ligation mice model and antiatherosclerosis effect as simvastatin in a model of New Zealand white (NZW) rabbits. It also demonstrated a great promise in alleviating non-alcoholic steatohepatitis (NASH) and liver fibrosis, attenuated alpha-naphthol isothiocyanate (ANIT)-induced cholestatic liver injury, and controlled blood glucose levels, making it a key player in the therapy of metabolic diseases. We also compiled OA semi-synthetic derivatives and explored their synthetic pathways and pharmacological effects on NRs, showcasing their structure-activity relationship (SAR). To the best of our knowledge, this is the first review article to highlight OA activity in terms of NRs modulation.

Natural laterite fixed-bed column intercalated with activated carbon prepared from Balanites ae-gyptiaca (BA-AC) was used for As(III) removal from an aqueous solution. Investigations were carried out to solve the problem of column clogging which appears during water percolation through the column. Experimental tests were conducted to evaluate the hydraulic conductivity and the effects of various parameters such as grain size, bed height, and initial As(III) concentra-tion. The breakthrough increased from 15 to 85 h with the increase of the bed height from 20 to 40 cm, and decreased from 247 to 32 h with the increase of initial As(III) concentration from 0.5 to 2 mg/L. The permeability data showed that the fixed-bed column filled with laterites layers intercalated with activated carbon performs much better than the non-intercalated adsorbent col-umn. The Bohart-Adams model showed that increasing the bed height induced a decrease in kAB and N0 values. The critical bed depths determined using the bed depth service time (BDST) mod-el for As(III) removal were 15.23 and 7.98 cm for 1 and 20% breakthrough, respectively. The re-sults showed that the new low-cost filtration system, based on laterite layers alternated with BA-AC layers, could be used for the treatment of arsenic-contaminated water.

Date palm trees generate large amounts of various types of waste, including leaf sheath fibers which can be used as a low-cost, precursor for production of biochar including activated carbon (AC) that can be employed for adsorption of contaminants. In the current study, activated carbon was made from leaf sheath fibers of date palm (LSDPFAC) by use of chemical activation with K2CO3, combined with microwave irradiation, characterized and evaluated for its adsorptive capacity of lead ions (Pb2+). The Brunauer–Emmett–Teller (BET) surface area, Langmuir surface area, total pore volume and average pore diameter of LSDPFAC were 560.20 m2/g, 744.31 m2/g, 0.29 cm3/g and 2.47 nm respectively. When the initial concentrations of Pb2+ were increased from 1 to 10 mg/L, Pb2+ adsorption increased from 0.97 to 8.76 mg/g, dry mass (dm) while the percent of Pb2+ removed decreased from 96.70 to 87.60%. The greatest removal of Pb2+ occurred at pH 13 with adsorption capacity of 9.15 mg/g, dm. Results of isotherm and kinetic studies demonstrated that adsorption of Pb2+ onto LSDPFAC was best described by the Freundlich isotherm and pseudo-second order (PSO) models. Langmuir monolayer adsorption capacity, Qm was 14.10 mg/g. Thermodynamic parameters of H°, S°, G° and Ea were 6.39 kJ/mol, 0.12 kJ/mol.K, -31.28 kJ/mol and 15.90 kJ/mol, respectively, which demonstrated that adsorption of Pb2+ by LSDPFAC was endothermic, spontaneous and governed by physisorption.

This study presents a novel polyurethane-activated carbon composite (PACC) as an effective and sustainable adsorbent for treating lead-ion-contaminated waters. The PACC was characterized using SEM-EDX, FTIR, BET, XRD, and TGA to evaluate its physicochemical and thermal properties. Furthermore, the PACC was employed in an experimental column adsorption setup to investigate its adsorption performance and to develop a dynamic method suitable for industrial implementation. Parameters such as bed height (50, 100, 150 mm), flow rate (4, 6, 8 mL min-1), pH (2, 4, 6), and initial metal ion concentrations (10, 50, 100 mg L-1) were examined. The experimental data exhibited strong agreement with the Thomas and Yoon-Nelson models (R2 ≥ 0.96), indicating efficient adsorption mechanisms. Remarkably, the depleted adsorbent has the potential for facile regeneration without substantial loss in capacity. The PACC demonstrated excellent adsorption performance for lead ions in aqueous solutions in a fixed-bed column system. Thus, the novel PACC material holds potential for scalable application in industrial settings to address water pollution challenges, especially in regions with uncontrolled effluent discharge.

Natural killer cells are associated with the pathogenesis of ulcerative colitis (UC), but their precise contributions remain unclear. The present study sought to investigate the diagnostic value of activated NK-associated genes (ANAGs) in UC. Bulk RNA-seq and scRNA-seq datasets were obtained from the Gene Expression Omnibus (GEO) and Single Cell Portal (SCP) databases. In the bulk RNA-seq, 92 differentially expressed genes (DEGs) were screened out by the “Batch correction” and “Robust rank aggregation” (RRA) methods. The immune infiltration landscape was estimated by single-sample gene set enrichment analysis (ssGSEA) and CIBERSORT, which revealed a higher abundance of activated NK cells in noninflamed UC tissues. 54 DEGs correlated with activated NK cells were identified as ANAGs. Protein-protein interaction (PPI) analysis and least absolute shrinkage and selection operator (LASSO) regression were utilized to screen out 4 key ANAGs (SELP, TIMP1, MMP7, and ABCG2) and establish an activated NK-associated gene score (ANAG score). The ANAG score demonstrated excellent diagnostic value and was validated in three external datasets. The expression of the 4 key ANAGs was validated in UC patients and healthy controls (HC) samples. Through scRNA-seq data analysis, higher expression levels of SELP, TIMP1, MMP7, and ABCG2 were observed in post-capillary venules, inflammatory fibroblasts, enterocytes, and immature enterocytes. The cell scores based on the ANAGs showed enrichment in endothelial cells and fibroblasts. In conclusion, we established and validated an ANAG score with the ability to precisely diagnose UC. The 4 key ANAGs have the potential to serve as therapeutic targets in UC.

The present study investigates the relationship between the local structure, photocatalytic ability, and cathode performances in sodium-ion batteries (SIBs) and lithium-ion batteries (LIBs) using Ni-substituted goethite nanoparticles (Ni_xFe_1-xOOH NPs) with a range of 'x' values from 0 to 0.5. The structural characterization was performed applying various techniques, including X-ray diffractometry (XRD), Thermogravimetry differential thermal analysis (TG-DTA), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray absorption spectroscopy (XANES/EXAFS), both measured at room temperature (RT), and ⁵⁷Fe Mössbauer spectroscopy recorded at RT and at low temperatures (LT) from 20 K to 300 K, Brunauer-Emmett-Teller surface area measurement (BET), and diffuse reflectance spectroscopy (DRS). In addition, the electrical properties of Ni_xFe_1-xOOH NPs were evaluated by impedance spectroscopy. XRD showed the presence of goethite as the only crystalline phase in prepared samples with x ≤ 0.20, and goethite and α-Ni(OH)₂ in the samples with x > 0.20. Sample with x = 0.10 (Ni10) showed the highest photo-Fenton ability with a first-order rate constant value (k) of 15.8×10^-3 min^-1. The ⁵⁷Fe Mössbauer spectrum of Ni0, measured at RT, displayed a sextet corresponding to goethite, with an isomer shift (δ) of 0.36 mm s^-1 and a hyperfine magnetic distribution (B_hf) of 32.95 T. Moreover, the DC conductivity decreased from 5.52×10^-10 to 5.30×10^-12 (Ω.cm)^–1 with 'x' increasing from 0.10 to 0.50. Ni20 showed the highest initial discharge capacity of 223 mAh g^-1, attributed to its largest specific surface area of 174.0 m² g^-1. In conclusion, Ni_xFe_1-xOOH NPs can be effectively utilized as visible-light-activated catalysts and active cathode materials in secondary batteries.

A large number of microplastics (MPs) have been found in various stages of wastewater treatment plants, which may affect the functional microbial activity in activated sludge and lead to unstable pollutant removal performance. In this study, the effects of different concentrations of polylactic acid microplastics (PLA MPs) on system performance, nitrification and phosphorus (P) removal activities, and extracellular polymeric substances (EPS) were evaluated. The results showed that under the same influent conditions, low concentrations (50 particles/(g TS)) of PLA MPs had no significant effect on effluent quality. The average removal efficiencies of chemical oxygen demand, phosphate and ammonia were all above 80%, and the average removal efficiencies of total nitrogen remained above 70%. High concentrations (200 particles/(g TS)) of PLA MPs inhibited the activities of polyphosphate accumulating organisms (PAOs) and nitrifying bacteria. The specific anaerobic P release rate decreased from 37.7 to 23.1 mg P/(g VSS·h), and the specific aerobic P uptake rate also decreased significantly. The specific ammonia oxidation rate decreased from 0.67 to 0.34 mg N/(g VSS·h), while the change in specific nitrite oxidation rate was not significant. The dosing of PLA MPs decreased the total EPS and humic acid content. As the concentration of PLA MPs increased, microbial community diversity increased. The relative abundance of potential PAOs (i.e., Acinetobacter) increased from 0.08% to 12.57%, while the relative abundance of glycogen accumulating organisms (i.e., Competibacter and Defluviicoccus) showed no significant changes, which would lead to improved P removal performance. The relative abundance of denitrifying bacteria (i.e., Pseudomonas) decreased from 95.43% to 58.98%, potentially contributing to the decline in denitrification performance.

Pleural mesothelioma (PM) comprises three main subtypes: epithelioid, biphasic and sarcomatoid, which have a different impact on prognosis and treatment definition. However, PM subtyping can be complex given the inter- and intra-tumour morphological heterogeneity. We aim to use immunohistochemistry (IHC) to evaluate five markers (Mesothelin, Claudin-15, Complement Factor B, Plasminogen Activator Inhibitor 1, and p21-activated Kinase 4), whose encoding genes have been previously reported as deregulated among PM subtypes. Immunohistochemical expressions were determined in a case series of 73 PMs, and cut-offs for the epithelioid and non-epithelioid subtypes were selected. Further validation was performed on an independent cohort (30 PMs). For biphasic PM, the percentage of the epithelioid component was assessed, and IHC evaluation was also performed on the individual components separately. Mesothelin and Claudin-15 showed a good sensitivity (79% and 84%) and specificity (84% and 73%) for the epithelioid subtype. CFB and PAK4 had an inferior performance, with higher sensitivity (89% and 84%), but lower specificity (64% and 36%). In the biphasic group, all markers showed a different expression when comparing epithelioid with sarcomatoid areas. Mesothelin, Claudin-15 and CFB can be useful in subtype discrimination. PAI1 and PAK4 can improve component distinction in biphasic PM.

In the last decades, studies on the inflammatory signaling pathways in multiple pathological contexts revealed new targets for novel therapies. Among the family of G-protein-coupled Proteases Activated Receptors, PAR2 was identified as a driver of the inflammatory cascade in many pathologies, ranging from autoimmune disease to cancer metastasis. For this reason, many efforts have been focused on the development of potential antagonists of PAR2 activity. This work focuses on a small molecule, 1-Piperidine Propionic Acid (1-PPA), previously described to be active against inflammatory processes, but whose target is still unknown. Stabilization effects observed by cellular thermal shift assay coupled to in-silico investigations, including molecular docking and Molecular Dynamics simulations, suggested that 1-PPA binds PAR2 in an allosteric pocket of the receptor inactive conformation. In addition, this compound was found able to inhibit platelet aggregation, a process mediated by PAR family members, including PAR2. Since the allosteric pocket binding 1-PPA is highly conserved in all the members of the PAR family, the evidence reported here suggests that 1-PPA could represent a promising new small molecule targeting PARs with antagonistic activity.

Bisphenol A is a remarkable chemical compound for its many applications mainly in the plastics industry, but also for its toxic effects on the environment and human health. BPA (4,4-isopropylidenediphenol) is an anthropogenic compound, moderately soluble in water (120 – 300 mg/l) at room temperature, and highly soluble in alkaline solutions, ethanol and acetone. BPA can bioconcentrate, bioaccumulate and biomagnify through food webs until it reaches humans. To prevent this, effective strategies are sought to allow its removal from the environment, through physico-chemical or enzymatic methods, advanced oxidation, adsorption and biodegradation, ultrasonic degradation. This article shows a comparative study regarding adsorption of BPA on Active carbon and zeolitic tuff, ZTC. In this paper, the characterization of the zeolitic tuff Rupea adsorbent, was carried out from an elemental and mineralogical point of view, pore size and elemental distribution, using SEM, EDAX, and XRD analysis. The pore size varies from 30 nm to 10 µm, atomic ratio Si/Al≥4, and the 80 % of mineralogical composition represent Ca Clinoptilolite zeolites Ca Clinoptilolite zeolite ((Na1.32K1.28Ca1.72Mg0.52)(Al6.77Si29.23O72)(H2O)26.84). Also, a comparative study of the adsorbtion capacity of bisphenol A from synthetic solutions on activated carbon type - Norit GAC 830 W, GAC, as well as on Clinoptilolite-type zeolitic tuff, ZTC, Rupea, was carried out. The experiments were carried out at a temperature of 20 ºC, a pH of 4.11; 6.98 and 8.12, and ionic strength being assured using KCl of 0.01 M, and 0.1 M. The adsorption capacities of GAC and ZTC tend to 115 mg/g and 50 mg/g respectively, at 8.12 pH and ionic strength of 0 M. The Langmuir mathematical model most faithfully describes the adsorption equilibrium of BPA. The maximum adsorption capacity for both adsorbents increases with increasing pH, and decreases with increasing ionic strength.

High-strength wastewaters from a variety of sources, including the food industry, domestic septage and landfill leachate, are often hauled to municipal wastewater treatment plants (WWTPs) for co-treatment. Due to their high organic loadings, these wastewaters can cause process upsets in both the WWTP’s liquid and solids treatment trains and consume organic treatment capacity, leaving less capacity available to service customers in the catchment area. A novel pre-treatment method, the Waste Activated Sludge-High Rate (WASHR) process, is proposed to optimize the co-treatment of high-strength wastewaters. The WASHR process combines the contact stabilization and sequencing batch reactor processes. It utilizes waste activated sludge from the municipal WWTP as its biomass source, allowing rapid start-up. Bench scale treatment trials of winery wastewater confirm the WASHR process can reduce loadings on the downstream WWTP’s liquid treatment and solids treatment trains. A case study approach is used to confirm the economic viability and environmental sustainability of the WASHR process compared to direct co-treatment using life cycle cost analyses and greenhouse gas emissions estimates.

Food waste disposal to landfills practice contributes to greenhouse problem due to the emission of gases such as methane to the atmosphere. Shelf-life extension of food products and further valorization of food wastes such as the conversion to activated carbon are tested nowadays as alternative techniques. The development and use of biobased active coatings against food oxidation/bacterial deterioration is an environmentally friendly technique. In this study, a novel food active coating was successfully developed based on a chitosan (CS)/poly-vinyl alcohol (PVOH) matrix activated with a nanohybrid of natural thymol (TO) adsorbed in activated carbon (AC) derived from spent coffee. The results shown that, compared to the pure CS/PVOH polymeric matrix, the coating with 15% wt. TO@AC nanohybrid concentration achieved +23.5 % Young’s modulus value, +20.1% ultimate strength value, increased barrier of +50.2% for water and +74.0 % for oxygen, +69.0% antioxidant activity, increased antibacterial activity of +5.5% against Escherichia coli, +17.8% against Salmonella enterica, +42.5% against Staphylococcus aureus, and +2.5% against Listeria monocytogenes. A visual evaluation of this coating shown a delay to fresh bananas enzymatic browning and significantly decrease their weight loss. This indicates that it could be potentially used to extend the shelf-life of fresh fruits.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

We previously showed that mice with knockout in the peroxisome proliferator-activated receptor gamma coactivator 1-alpha (PPARGC1A) gene encoding the PGC-1a protein and nuclear factor erythroid 2 like 2 (NFE2L2) gene, showed some features of the age-related macular degeneration (AMD) phenotype. To further explore the mechanism behind the involvement of PGC-1a in AMD pathogenesis we used young (3-month) and old (12-month) mice with knockout in the PPARGC1A gene and age-matched wild-type (WT) animals. An immunohistochemical analysis showed age-dependent different expression of markers of oxidative stress defense, senescence and autophagy in the retinal pigment epithelium of KO animals as compared with their WT counterparts. Multivariate inference testing showed that senescence and autophagy proteins had the greatest impact on the discrimination between KO and WT 3-month animals, but proteins of antioxidant defense also contributed to that discrimination. A bioinformatic analysis showed that PGC-1a might coordinate the interplay between genes encoding proteins involved in antioxidant defense, senescence and autophagy in the aging retina. These data support importance of PGC-1a in AMD pathogenesis and confirm the utility of mice with PGC-1a knockout as an animal model to study AMD pathogenesis.

Chronic pain is a significant health problem worldwide. Recent evidence has suggested that dysfunctional states of the ventral hippocampus, including decreased neuronal excitability and connectivity with other brain regions, parallel pain chronicity and persistent nociceptive hypersensitivity in humans and rodents, respectively. But the molecular mechanisms underlying hippocampal modulation of pain remain poorly elucidated. In this study, we used ex vivo whole-cell patch-clamp recording, immunofluorescence staining and behavioral tests to examine whether hyperpolarization-activated cyclic nucleotide-gated channels 2 (HCN2) in the ventral hippocampal CA1 (vCA1) were involved in regulating nociceptive perception and CFA-induced inflammatory pain in mice. Reduced sag potential and firing rate of action potentials were observed in vCA1 pyramidal neurons from CFA-injected mice. Moreover, the expression of HCN2, but not HCN1, in vCA1 decreased in mice injected with CFA. HCN2 knockdown in vCA1 pyramidal neurons induced thermal hypersensitivity, whereas over-expression of HCN2 alleviated thermal hyperalgesia induced by intraplantar injection of CFA in mice. Our findings suggests that HCN2 in the vCA1 plays an active role in pain modulation and could be a promising target for the treatment of chronic pain.

The volatile fatty acids (VFAs) productions, as well as particulate organics decomposition, soluble chemical oxygen demand (SCOD) yield, and the VFAs production pathways, of mesophilic and thermophilic anaerobic fermentation were investigated. Batch experiments showed that the decomposition rate of volatile suspended solids (VSS), particulate carbohydrate (P-C) and particulate protein (P-P) followed the first-order kinetic model at different temperature. However, the intermediates， accumulated in the process of protein or carbohydrate digestion had a more significant inhibitory effect on the production of VFAs during the mesophilic anaerobic acidification process. Thermophilic fermentation led to more accumulation of VFAs compared to mesophilic fermentation. Then 13C stable isotope labeling experiment demonstrated that, acetic (HAc), propionic (HPr) and butyric (HBu) could be produced from carbohydrate and protein digestion, but valeric (HVa) was only generated from the degradation of protein. Finally, the possible pathway of HVa synthesis was proposed.

Plasma-activated water (PAW) is an emerging and promising green technology in the agriculture sector during recent years. The aim of this study was to examine the influence of the spraying of PAW and amino acid fertilizer concentrations on the physiological, biochemical and phytochemical characteristics of German chamomile varieties under field conditions. Method: The experiment was performed during 2020–2021 as a factorial using a randomized complete block design with three replications, in an arid and warm region. The factors contained five fertilizer levels (0 (control), 1, 2, 3 ml·L−1 amino acid and PAW) and three German chamomile cultivars Bona, Bodegold, Lianka). Physiological, biochemical and phytochemical traits such as plant height, fresh and dried flower weight, chlorophyll a, b, carotenoids, CHN elements, C:N ratio, total protein, amino acid profile, essential oil yield, apigenin content and major secondary metabolites were examined. Results: The ANOVA indicated that the impact of the cultivar and fertilizer was significant on all physiological, biochemical and phytochemical studied parameters. The amino acid fertilizer and PAW enhanced physiological features, hydrogen, C:N ratio, essential oil yield, apigenin content and main phytochemical compositions like chamazulene and α-bisabolol, but it had no incremental effect on the carbon, nitrogen, and total protein percentage. Conclusion: Findings revealed that the application of foliar amino acid fertilizer and PAW treatments improves physiological, biochemical and phytochemical parameters in German chamomile cultivars under field conditions.

Lewis acid zeolites play an important role in industrially important green reactions closely related to fine chemicals and biomass conversion. Titanium-doped TS-1 zeolite is a milestone Lewis acid zeolite, which widely uses in industrially significant green oxidation processes with hydrogen peroxide as an oxidant under mild conditions. TS-1 Zeolites are normally synthesized in basic condition under hydrothermal treatment. Up to now, it is still not successful to synthesize active TS-1 Lewis acid zeolite by using inorganic alkali, e.g. NaOH or KOH as base, which are cheaper and more stable compared with quaternary ammonium hydroxide or organic amines used in the traditional synthesis. Here, inorganic base of NaOH was firstly employed in synthesizing active TS-1 zeolites. The crucial factor was the control of adverse effects of sodium cations on the incorporation of active titanium cations. A higher catalytic activity could be achieved by further reducing the size of the TS-1 crystal by seed-added strategy, which could approach the catalytic activity of commercial catalyst while the production cost was much lower than the commercial TS-1 catalysts, indicating great commercial potential and the possibility of preparing other cheap Lewis acid catalysts by using inorganic alkali.

(1) Background: Angiotensin II, a major culprit in cardiovascular disease, activates mediators that are also involved in pathological cardiac remodelling. We aimed at investigating the effects of two of them: aldosterone (Ald) and transforming growth factor-beta-1 (TGF-β1 ), on cardiac remodelling in an in vivo model. (2) Methods: Six-week-old male wild-type (WT) and TGF-β1 -overexpressing transgenic (TGF-β1 -TG) mice were infused with subhypertensive doses of Ald for 2 weeks, and/or treated orally with eplerenone from postnatal day 21. Heart’s ventricles were examined: by morphometry, immunoblotting to assess intracellular signalling pathways, RT qPCR to determine hypertrophy and fibrosis marker genes. (3) Results: TGF-β1 -TG mice spontaneously developed cardiac hypertrophy and interstitial fibrosis, exhibited higher baseline phosphorylation of p44/42 and p38 kinases, fibronectin and ANP mRNA expression. Ald induced a comparable increase in ventricular heart weight-to-body-weight ratio and cardiomyocyte diameter in both strains, but less pronounced increase in interstitial fibrosis in transgenic compared to WT mice (23.6% vs 80.9%, p&lt;0.005). Ald increased phosphorylation of p44/42 and p38 in WT but not TGF-β1 -TG mice. While eplerenone-enriched chow partially prevented Ald-induced cardiac hypertrophy in both genotypes and interstitial fibrosis in WT controls, it completely protected from additional fibrosis in transgenic mice. (4) Conclusions: Ald appears to induce cardiac hypertrophy independently of TGF-β1 , while in case of fibrosis downstream signalling pathways of these two factors probably converge

In this work, a novel silane coupled cationic precursor (SAGS) was synthesized by 3-glycidyloxypropyltrimethoxysilane and sodium 2-((2-aminorthyl)amino) ethanesulfonate. A series of cation exchange membranes were prepared with poly(vinyl alcohol) (PVA) and SAGS by sol-gel process. The structure of the prepared membranes were characterized by fourier transform infrared spectrum (FTIR) and scanning electron microscopy (SEM), and its properties were studied by water uptake (WR), cation exchange capacity (CEC), linear expansion ratio (LER), alkali stability, thermogravimetric analysis (TGA), mechanical properties and diffusion dialysis performance. FTIR and X-ray photoelectron spectroscopy (XPS）confirmed the successful preparation of SAGS membranes, and SEM images showed that the prepared membranes were dense and uniform. The WR values of the SAGS membranes were in the range of 91.49-122.39 %, and the LER values were 17.65-28.21 %. In addition, the SAGS membranes had suitable CEC value, good alkali resistance and thermal stability which ensured the application of membranes in the field of diffusion dialysis (DD) for alkali recovery. In DD test, the dialysis coefficients of NaOH (UOH) ranged from 0.012 mm/h to 0.023 mm/h, and the separation factors (S) was in the range of 30.77-16.43. In summary, the prepared membrane had good performance and simple preparation process, which had great application potential in textile industrial wastewater recovery.

The goal of this work is to develop a sustainable value chain of carbonaceous adsorbents that can be produced from the solid fibrous digestate (SFD) of biogas plants and further applied in integrated desulphurisation-upgrading (CO2/CH4 separation) processes of biogas to yield high purity biomethane. On this purpose, physical and chemical activation of the SFD derived biochar was optimised to afford micro-mesoporous activated carbons (ACs) of high BET surface area (590-2300 m2g−1) and enhanced pore volume (0.57-1.0 cm3g−1). Gas breakthrough experiments from fixed bed columns of the obtained ACs, using real biogas mixture as feedstock, unveiled that the physical and chemical activation conclude to different types of ACs which are sufficient for biogas upgrade and biogas desulphurisation respectively. Performing breakthrough experiments at three temperatures close to ambient it was possible to define the optimum conditions for enhanced H2S/CO2 separation. It was also concluded that the H2S adsorption capacity is significantly affected by restriction to gas diffusion. Hence, the best performance was obtained at 50 oC and the maximum observed in the H2S adsorption capacity vs the temperature is attributed to the counterbalance between adsorption and diffusion processes.

Benign design of alkali-activated slag/FA geopolymer paste has intriguing increasing attention for optimizing its service performance. Therefore, the replacement of fly ash (FA) with 10 wt% silica fume (SF) is investigated by mechanical strength after freeze-thawing cycles and microstructure characterization. The results show that an appropriate dosage (30 wt%) of slag is necessary to attain alkali-activated slag/FA geopolymer paste with excellent mechanical performance, and the SF/slag/FA (SF: slag: FA= 10:30:60, wt%) geopolymer paste exerts the compressive and flexural strength of 95.2 and 3.2 MPa, respectively. Meanwhile, the doped 10 wt% SF facilitates the propagation of (N, C)-A–S–H chains, rather than the formation of C-S-H gels, evidenced by the absent exothermic peak at about 861oC from the differential scanning calorimetry (DSC) curves, leading to the increases in the pores volume with a pore diameter<20 nm and tortuosity by mercury intrusion porosimeter (MIP) results, corresponding to an improved freezing-thawing resistance with the residual compressive strength of 52.8 MPa and the weight loss of 10.5% after 300 freeze-thawing cycles. It explores a cost-effective and benign facile approach to designing heating curing-free alkali-activated slag/FA geopolymer paste with good freezing-thawing resistance.

Nowadays, bioeconomy and nanotechnology trends push food packaging sector in the re-placement of food additives by biobased antioxidant/antibacterial compounds and their inclusion in nanocarriers to control their release. Herein by following this trend, a rich in thymol-(TO) activated carbon (AC) nanostructure (TO@AC) was prepared and physiochemically characterized with various technics. This TO@AC nanostructure as well as pure AC were extruded with low density polyethylene (LDPE) to develop novel active packaging LDPE/TO@AC and LDPE/AC films. X-ray diffractometry, Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy measuraments shown high dispersity and capability of both AC and TO@AC in LDPE matrix which was resulted in enhanced tensile and water/oxygen barrier properties of obtained LDPE/AC and LDPE/TO@AC films. LDPE/TO@AC films shown higher elongation at break values and water/oxygen barrier than LDPE/AC films and significant antioxidant activity. TO release kinetics studies shown that by increasing TO@AC content the total TO amount released increased and the constant release rate decreased. Pork fillets wrapped with the optimum active film containing 15 wt.% TO@AC and succeed to prevent lipid oxidation and heme iron loss during storage. Estimation of microbial population of pork fillets shown that this active film could ex-tend the microbiological shelf-life of pork fillets by 2 days

In the present work, a comparative evaluation of an MBBR unit performance was carried out for the following cases: when adding 3D-printed biocarriers fabricated with 13X and bentonite, when using K1 commercial biocarriers and when not adding biocarriers at all. For the evaluation of the MBBR efficiency, various physicochemical parameters were measured, while static light scattering and optical microscopy observations were additionally used. Finally, biofilm extracted from the biocarriers was evaluated. The findings suggest that there is an optimal biodegradation of the organic load in all MBBR units. The nitrification and denitrification process were improved at the 3D MBBR as compared to the control MBBR and MBBR K1. The dry mass of the biofilm in the 3D-printed biocarriers was two orders of magnitude larger than the one in the K1 biocarriers. What is more, in the K1 biocarriers the mass of the biofilm varied in relation to time, due to the fact that it could not be kept inside the holes, something that was not observed to happen with the 3D-printed biocarriers. Finally, it was observed, mostly in the 3D MBBR and less in the K1 MBBR, that the growth of nitrifying bacteria and heterotrophs inside the units increased the biomass production in the form of SMP, which in turn favored the adhesion of biomass on the surface of biocarriers.

An attempt to investigate the effect of binary composite activators on the microstructure of fly ash-based geopolymers is conducted through the comparison of 24 experiments, which consisted of Na2SiO3•9H2O, Na2CO3, K2CO3, NaOH, and KOH through a facile preparation technique. The results show that the activator of Na2SiO3•9H2O+KOH presents the highest mechanical strength, due to the synergy activation between the inherent ≡Si-O-Si≡ chains derived from Na2SiO3 and K+’s catalysis. It reveals that the K+ plays a crucial role in Na2SiO3-activated fly ash geopolymer, which is the rate-determining step of the enhanced crosslinking and propagation of N-(C)-A-S-H chains, leading to an increase in weight loss temperatures of specimens from TG/DTG results. Furthermore, the adding silica fume facilitates as-formed amorphous silicates, which also could fill into the pores of N-(C)-A-S-H amorphous gels and present a uniform and compact morphology, leading to an increase in the pore volume of the pore diameter less than 100 nm. It explores an efficient and cost-effective preparation of fly ash-based geopolymer for developing solid-waste recycling techniques.

Liver fibrosis is a critical health issue with limited treatment options. This study investigates the potential of PGC-Sec, a secretome derived from PGC-1α-overexpressing adipose-derived stem cells (ASCs), as a novel therapeutic strategy for liver fibrosis. Upon achieving a cellular confluence of 70-80%, ASCs were transfected with pcDNA-PGC-1α. PGC-Sec, obtained through concentration of conditioned media using ultrafiltration units with a 3-kDa cutoff, was assessed through in vitro assays and in vivo mouse models. In vitro, PGC-Sec significantly reduced LX2 human hepatic stellate cell proliferation and mitigated mitochondrial oxidative stress compared to control-secretome (Ctrl-Sec). In an in vivo mouse model, PGC-Sec treatment led to notable reductions in hepatic enzyme activity, serum pro-inflammatory cytokine concentrations, and fibrosis-related marker expression. Histological analysis demonstrated improved liver histology and reduced fibrosis severity in PGC-Sec-treated mice. Immunohistochemical staining confirmed enhanced expression of PGC-1α, OPA1 (a mitochondrial function marker), and PPARα (an anti-fibrogenic marker) in the PGC-Sec-treated group, along with reduced Collagen 1A expression (a pro-fibrogenic marker). These findings highlight the therapeutic potential of PGC-Sec in combating liver fibrosis by enhancing mitochondrial biogenesis and function, and promoting antifibrotic processes. PGC-Sec holds promise as a novel treatment strategy for liver fibrosis.

The fireproof design of geopolymer has intriguing increasing attention by adjusting multi-component metallurgical solid wastes, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical strength of slag/FA (slag: FA=30:70, wt.%) geopolymers during building fires. The results show that the replacement of FA with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm, leading to an increase in the compressive or flexural strength below 850℃, “right shifts” of the endothermic peak, appearing uniform and compact fracture surfaces. Meanwhile, the gehlenite and labradorite generate after exposure above 850℃. While the bloating effect of the SF-containing sample occurs at 1200℃, leading to a greater deformation, due to the further restructuring of the amorphous geopolymer chain N-A-S-H or N-(Ca)-A-S-H composed from the [SiO4]4− and [AlO4]5−. It explores an effective approach for improving geopolymer’s fireproof performance by adjusting the solid-waste formulation.

This paper describes the influence of the regeneration treatments on 4-chloro-2-methyl-phenoxyacetic acid (MCPA)-loaded activated carbons (ACs) on adsorption-desorption cycles with two commercial ACs, Merck and Norit 1240 X ( Norit 1240 X was used in a granular and powder form). The ACs were saturated with MCPA and then submitted to four regeneration cycles, by washing with ethanol, NaOH solutions and washed with NaOH solutions followed by a thermal treatment. The ACs regenerated with ethanol showed a better performance concerning the successive adsorption-desorption cycles. On the first cycle, the MCPA desorbed, from washing with ethanol, from all ACs was higher than 99%. After a fourth adsorption-desorption cycle, washing regeneration combined with thermal treatment allowed excellent regeneration results. The amount of MCPA adsorbed on Norit 1240 X AC was higher than the amount adsorbed in the first cycle. MCPA adsorption kinetic data were analyzed by applying pseudo-first-order, pseudo-second-order, and Weber-Morris models. The pseudo-second-order fit better fit to the data and the Weber-Morris representation allows confirming that on Norit 1240 X, in a granular form, the pore diffusion was the limiting factor concerning the MCPA adsorption.

The Bayer process is the maim method of alumina production worldwide. The use of low-quality bauxites for alumina production results in the formation of a significant amount of technogenic waste - bauxite residue (BR). The Bayer reductive method is one possible way to eliminate BR stockpiling, but it requires high-pressure leaching at temperatures higher than 220 °C. In this research, the possibility of boehmitic bauxite atmospheric pressure leaching at both the first and second stages or high-pressure leaching at the second stage with the simultaneous reduction of hematite was investigated. Bauxite and solid residue after NaOH leaching were characterized using XRD, SEM-EDS, and Mössbauer spectroscopy methods. The first stage of leaching under atmospheric pressure with the addition of Fe(II) species in a strong alkali solution (330-400 g L–1 Na2O) results in a partial reduction of the iron minerals and an extraction of more than 60% of Si and 5-25% of Al (depending on caustic modulus of solution) after 1 h. The obtained desilicated bauxite was subjected to atmospheric leaching at 120 °C in a strong alkali solution (350 g L-1) or high-pressure leaching at 160-220 °C using the Bayer process mother liquor in order to obtain a concentrate with a magnetite content higher than 83 wt. %.

In this paper, mesoporous electrodes consisted of Sb-doped SnO2 deposited onto Ti plates controlled corroded under acidic medium were synthesized by spin-coating method, and morpho structurally characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrodes were electrochemical testing in the degradation/mineralization by electrooxidation (EO) of doxorubicin (DOX) as single-component and multi-component together with capecitabine (CCB)-from cytostatic class and humic acid (HA)-from natural organic matter (NOM) class in the absence/the presence of activated carbon (AC) as particulate electrode. The best mineralization efficiency of 67 % was achieved for DOX mineralization using Sb-doped SnO2 deposited onto Ti plate controlled corroded with oxalic acid in electrooxidation process. The presence of AC within the electrolysis process generated a synergy effect of 52.75 % for TOC parameter removal, which is in accordance and quite better than the result reported in the literature. The aspects related to the complex mechanism of DOX degradation and mineralization are discussed. The superiority of AC assisted electrooxidation, as electrochemical filtering (EF), was proved considering simultaneous degradation and mineralization of mixture of doxorubicin, capecitabine and humic acid.

Soarinho Alkaline Intrusion, southeastern Brazil, makes part of the Serra do Mar Igneous Province, and it is composed of alkali feldspar syenite, alkali feldspar trachyte, quartz syenite, and mon-zonite. Geochemical and geochronological analysis of the Soarinho were compared with data from its neighbors Rio Bonito and Tanguá. Zircon U-Pb Laser Ablation ages show that Soarinho is youngest than Rio Bonito and Tanguá. Ages obtained from the monzonite (60 ± 2 Ma), alkali feldspar syenite (58 ± 2 Ma), and quartz syenite (58 ± 2 Ma) are indistinguishable within error. Petrographic and geochemical data show a clear contrast among Soarinho, Rio Bonito, Tanguá, and Lu-Hf isotopic data for the three alkaline intrusions (all negative), point to some similarities in their sources. The data suggest an enriched mantle source for Soarinho; however, an older con-tinental crust contribution cannot be discarded.

Titanium (Ti-6Al-4V) substrates were functionalized through the covalent binding of fibronectin, and the effect of the presence of this extracellular matrix protein on the surface of the material was assessed employing mesenchymal stem cell (MSC) cultures. The functionalization process com-prised the usage of the activation vapor silanization (AVS) technique to deposit a thin film with a high surface density of amine groups on the material, followed by the covalent binding of fi-bronectin to the amine groups using the N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide hy-drochloride / N-hydroxysuccinimide (EDC/NHS) crosslinking chemistry. The biological effect of the fibronectin on murine MSCs was assessed in vitro. It was found that functionalized samples not only showed enhanced initial cell adhesion compared with bare titanium, but also a three-fold increase in the cell area, reaching values comparable to those found on the polystyrene controls. These results represent a clear indication of the potential of modulating the response of the or-ganism to an implant through the covalent binding of extracellular matrix proteins on the pros-thesis.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Common bean (Phaseolus vulgaris L.) is an important crop for food security and for national economics for several countries worlwide. One of the most important factors of risk in common bean production is the fungal disease anthracnose caused by Colletotrichum lindemuthianum, which in some cases, causes complete yield losses; this kind of plant disease is usually managed through the application of chemical products such as fungicides, that are commonly not accepted by society, this rejection is based on the relationship of pesticides with health damage and environmental contamination. In order to help in solving this drawbacks, the present work propose the use of Electrochemically Activated Salt Solutions(EASS) as a safer pathogen control agent in crops due to it have shown an elicitor and biostimulant effect on plants such as tobacco and apple. With this background, this manuscript presented in vitro results of the evaluation of the inhibitory effect for multiple bean pathogens and in vivo results of EASS in the common bean-Colletotrichum pathosystem by in vitro evaluations of the inhibitory effect for multiple bean pathogens and in vivo evaluation of the infection severity and defense activation such as secondary metabolites production and antioxidant activity. EASS presence in growth media had strong inhibitory effect, at beginning of experiment, for some of the evaluated fungi. EASS showed effect against the development of the disease when applied in specific doses to prevent distress in plants.

Along with the rapid development of technology and industry, the need for energy storage has become fundamental. One promising energy storage devices is the supercapacitor. Several type supercapacitors are available, one of which is the electrical double-layer capacitor made from carbon graphite and multiwalled carbon nanotubes (MWCNTs). In this study, we combined these two materials into a working electrode in a three-electrode system. In the morphological analysis using scanning electron microscope, transmission electron microscope, and X-ray diffraction, the two materials were found to have formed a composite on the surface. In the electrochemical analysis, two types of testing were conducted using cyclic voltammetry and electrochemical impedance spectroscopy. Electrochemical analysis was carried out on five electrolyte concentrations of Na2SO4 from 1 to 6 M. The capacitance produced at concentrations of 1, 2, 3, 4, and 5 M were 34.395, 35.808, 46.284, 49.502, and 76.815 F/g, respectively. At an electrolyte concentration of 5 M Na2SO4, an energy density of 27.312 Wh/Kg and a power density of 343.786 W/Kg were produced. Meanwhile on concentration of 6 M, the surface of the electrode was damaged.

Alcohol effects on hepatic lipid metabolism through various mechanisms, leading synergistically to an accumulation of fatty acids (FA) and triglycerides. Obesity, as well as, the dietary fat [saturated fatty acids (FA) versus poly-unsaturated fatty acids (PUFA)] may modulate the hepatic fat. Alcohol inhibits adenosine monophosphate activated kinase (AMPK). AMPK activates peroxisome proliferators activated receptor a (PPARα) and leads to a decreased activation of sterol regulatory element binding protein 1c (SRABP1c). The inhibition of AMPK, and thus of PPARα results in an inhibition of FAs oxidation. This ß-oxidation is further reduced due to mitochondrial damage induced through cytochrome P4502E1 (CYP2E1) driven oxidative stress. Furthermore, the synthesis of FAs is stimulated through an activation of SHREP1. In addition, alcohol consumption leads to a reduced production of adiponectin in adipocytes due to oxidative stress and to an increased mobilization of FAs from adipose tissue and from the gut as chylomicrons. On the other side, the secretion of FAs via very low density lipoproteins (VLDL) from the liver is inhibited by alcohol. Alcohol also affects signal pathways such as early growth response 1 (Egr-1) associated with the expression of tumour necrosis factor  (TNF), and the mammalian target of rapamycin (mTOR) a key regulator of autophagy. Both have influence the pathogenesis of alcoholic fatty liver. Alcohol-induced gut dysbiosis is contributing to the severity of ALD by increasing metabolism of ethanol in the gut and promoting intestinal dysfunction. Moreover, pathogen associated molecular paterns (PAMPS) via specific Toll-like receptors (TLR) bacterial overgrowth is leading to the translocation of bacteria. Endotoxins, and toxic ethanol metabolites enter the enterohepatic circulation reaching the liver, inducing the activation of the nuclear factor kappa-B (NFB) pathway. Pro-inflammatory cytokines released in the process contribute to inflammation and fibrosis. In addition, cellular apoptosis is inhibited in the favor of necrosis.

Gold-centered carbene-metal-amides (CMAs) containing cyclic (alkyl)(amino)carbenes (CAACs) are promising emitters for thermally activated delayed fluorescence (TADF). Aiming at design and optimization of new TADF emitters, we report a density functional theory study of over 60 CMAs with various CAAC ligands, systematically evaluating computed parameters in relation to photoluminescence properties. We demonstrate that the efficiency of TADF of CMAs, arising from a compromise of exchange energy and oscillator strength, is governed by the overlap of HOMO and LUMO orbitals, where HOMO is localized on amide and LUMO on Au-carbene. The S0 ground states and excited T1 states of the CMAs adopt approximately coplanar geometries of carbenes and amides, but rotate perpendicular in the excited S1 states, resulting in degeneracy or near-degeneracy of S1 and T1, accompanied with lowering of the S1-S0 oscillator strength from its maximum at coplanar geometries to near zero at rotated geometries. Based on computations, promising new TADF emitters are proposed and synthesized. Bright CMA complex (Et2CAAC)Au(carbazolide) is obtained and fully characterized to demonstrate that high radiative rates up to 106 s-1 can be obtained for the gold-CMA complexes with small CAAC-carbene ligands.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

Vascular calcification (VC) is associated with increased cardiovascular risks in patients with chronic kidney disease (CKD). Sodium-glucose cotransporter 2 inhibitors, like empagliflozin, can improve cardiovascular and renal outcomes. We assessed the expression of Runt-related transcription factor 2 (Runx2), interleukin (IL)-1β, IL-6, AMP-activated protein kinase (AMPK), nuclear factor erythroid-2-related factor (Nrf2), and heme oxygenase 1 (HO-1) in inorganic phosphate–induced VC in mouse VSMCs to investigate the mechanisms underlying empagliflozin’s therapeutic effects. We evaluated biochemical parameters, mean artery pressure (MAP), pulse wave velocity (PWV), transcutaneous glomerular filtration rate (GFR), and histology in an in vivo mouse model with VC induced by an oral high-phosphorus diet following a 5/6 nephrectomy in ApoE−/− mice. Compared to the control group, empagliflozin-treated mice showed significant reductions in blood glucose, MAP, PWV, and calcification, as well as increased calcium and GFR levels. Empagliflozin inhibited osteogenic trans-differentiation by decreasing inflammatory cytokine expression and increasing AMPK, Nrf2, and HO-1 levels. Empagliflozin mitigates high phosphate–induced calcification in mouse VSMCs through the Nrf2/HO-1 anti-inflammatory pathway by activating AMPK. Animal experiments suggested that empagliflozin reduces VC in CKD ApoE−/− mice on a high-phosphate diet.

The present work aims to explain the aluminum hydrolysis reaction kinetics based on properly chosen theoretical model with machined aluminum waste chips and alkali solutions up to 1M as a promoter, and to estimate overall reaction profit. In order to obtain results of better accuracy, we work with flat Al waste chips because a flat surface is preferable to maximally increase the time for created hydrogen bubbles to reach the critical gas pressure. At describing the reaction kinetics, flat shape allows using a planar one-dimensional shrinking core model instead of much complicated polydisperse spheric shrinking core model. We analyze the surface chemical reaction and mass transfer rate steps to obtain the first order rate constant for surface reaction and the diffusion coefficient of aqueous reactant in the byproduct layer, respectively. With our reactor we achieved H2 yield of 1145 mL per 1 g Al with 1M NaOH, which is 92% of the theoretical maximum. At estimation of the profit, we pay much attention to the loss of alkaline and find a crucial dependence on its price. Nevertheless, in terms of consumed and originated materials for sale, conversion of the aluminum waste material into green hydrogen by properly chosen reaction parameters has a positive profit even by consuming alkali of chemical grade.

Recycling of metallurgical solid waste has intriguing increasing attention for fabricating cementitious materials, due to its low-carbon emission, cost-effectiveness, and environmental conservation. Herein, the effects of silica fume (SF) on the microstructure and mechanical properties of alkali-activated slag/FA (fly ash) pastes subjected to elevated temperatures (150, 500, 850, and 1200℃) are investigated, to clarify the fact that whether or not the SF generates positive roles in mechanical properties of slag/FA geopolymers. The results show that the replacement with 10 wt% SF (silica fume) promotes the increasing pore volume with a diameter of 0.2~3 μm at room temperature, leading to an increase in the compressive or flexural strength, “right shifts” of endothermic peak and the initial-final temperature of mass loss, presenting a denser and compact fracture surface. Meanwhile, the mineral phase of gehlenite and labradorite emerges after exposure above 850℃ from the XRD results. Furthermore, the bloating effect of the incorporated SF occurs due to the formation of a liquid phase altogether with the amorphous silicates after exposure to 1200℃, leading to a greater deformation and enhancement of restructuring involved in the [SiO4]4− and [AlO4]5−. It explores an effective recycling approach for fabricating paste binders using metallurgical solid wastes.

Activated Corrosion Products (ACPs) formation and deposition pose a critical safety issue for nuclear fusion reactors. The working fluid transports the ACPs towards regions accessible to worker personnel. Predicting ACPs formation deposition and transport is fundamental for source term identification, reduction of radiation exposure assessment, maintenance plan definition, design optimization, and waste management. The code OSCAR-Fusion has been developed by the CEA (France) to evaluate the ACPs generation and transport in closed water-cooled loops for fusion application. This work aims at assessing the impact of water chemistry on the transport, precipitation, and deposition of corrosion products for the EU-DEMO divertor Plasma Facing Unit Primary Heat Transfer System. Sensitivity analyses and uncertainty quantification are needed due to the multi-physics phenomena involved in ACPs formation and transport. The OSCAR-Fusion/RAVEN code coupling developed by the Sapienza University of Rome and ENEA has been used. This work presents the perturbation results of different parameters chosen for a closed water-cooled loop considering a continuous scenario of 1888 days. The aim of this work is to assess the variation of build-up of ACPs, perturbing the alkalizing agent concentration into the coolant and the corrosion and release rates of different materials.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

Due to its high specific surface area and rich porous structure, acacia-derived porous activated carbon is the most potentially effective material for wastewater treatment. This research study aimed to prepare activated carbon using Acacia erioloba seedpods as carbonaceous materials and phosphoric acid as an activating agent. The specific surface area of the prepared activated carbon sample was characterised by Brunauer–Emmett–Teller instrument. The specific surface area value was 387 m²/g. The activated carbon prepared was then sieved into three different particle sizes of 50, 100 and 200 micrometres and characterised using various analytical procedures, including proximate analysis to study moisture content, ash content, volatile matter content and fixed carbon content. The bulk density, SEM, power of hydrogen, iodine number and methylene blue number index were also investigated to determine the adsorption properties of the prepared activated carbon. Batch adsorption dynamics for the removal of organic compounds such as methylene blue and unsaturated character of fatty acid from aqueous solution were also carried out at room temperature to evaluate the prepared activated carbon's applicability in water treatment. The iodine number was 528, 638, and 554 mg/g for the 50, 100, and 200 μm activated carbon particles, respectively. From the results, the adsorption of methylene blue favoured the Freundlich adsorption model, showing higher correlation (R²) values than the Langmuir model. The results indicate that methylene blue particles were adsorbed on heterogeneous surfaces.

Calcium-activated potassium channels (KCa) are the important participants in calcium signaling pathways due to their ability to be activated by increase of the intracellular free calcium concentration. KCa channels are involved in the regulation of various processes in the cells under normal, as well as pathophysiological conditions, including oncotransformation. Previously, with the use of patch-clamp method, we registered the KCa activity in the plasma membrane of human myeloid leukemia K562 cell line. Here, we performed the molecular and functional identification of KCa channels and have uncovered their role in proliferation, migration and invasion of K562 cells. Using a combined approach, we identified the functional activity of SK2, SK3 and IK channels in the plasma membrane of the cells. Selective SK and IK channel inhibitors, apamin and TRAM-34, reduced the proliferative, migratory and invasive capabilities of human myeloid leukemia cells. At the same time, the viability of K562 cells was not affected by KCa channel inhibitors. Our data imply that SK/IK channel inhibitors could be used to slow down the proliferation and spreading of leukemia cells that express functionally active KCa channels in the plasma membrane.

A separate group consists of compounds that are able to simultaneously interact with both orthosteric and allosteric sites, which are classified as bitopic GPCR ligands [74, 76-81]. They have two pharmacophores, one of which binds with high affinity to the orthosteric site, while the other, with lower affinity, binds to the allosteric site. If these sites are spatially separated in the receptor, then the pharmacophores in the bitopic ligand must be connected with a flexible linker, the length of which exactly corresponds to the distance between the orthosteric and allosteric sites. At the same time, it is important that the linker does not significantly affect the conformational rearrangements in the receptor caused by its activation by orthosteric and (or) allosteric agonists [74, 79].

The assessment of an organization/product's environmental footprint is based on the protocols developed by the Joint Research Centre of the European Union, which take into account 16 impact categories. Among the categories covered are toxicity to freshwater ecosystems and to humans. Standard protocols use only chemical parameters as input data, preventing the true impact of entire complex mixtures, such as emissions discharged into the environment, from being determined. Biological assays allow us to bridge this gap: in the current study, assays were used to determine baseline toxicity towards aquatic organisms (green algae, luminescent bacteria, and crustaceans) as well as specific toxicity (mutagenicity and carcinogenicity). Expected impacts were compared using two approaches (standard and bioassay-centered results obtained are not always in line and, in general, the traditional method underestimates impacts). This demonstrates the importance of these assays and suggests that they be used in LCA (Life Cycle Assessment) protocols as well.

Bauxite residue (BR), also known as red mud, is a by-product of the production of alumina via the Bayer process. Because of the high sodium oxide and other impurities content, this material is not used to obtain iron or other iron-containing products. In this paper, the hydro-chemical conversion of goethite (FeOOH) to magnetite (Fe3O4) in high-iron BR from the Friguia alumina refinery (Guinea) by Fe2+ ions in highly concentrated alkaline media was studied. The simultaneous extraction of Al and Na made it possible to obtain a product containing more than 96% Fe3O4. The results show that the magnetization of Al-goethite and Al-hemetite accelerates the dissolution of the Al from the iron mineral solid matrix and from the desilication product (DSP). After ferrous sulfate (FeSO4·7H2O) was added directly at the FeO:Fe2O3 molar ratio of 1:1 at 120 °C for 150 min in the solution with the 360 g L-1 Na2O concentration, the alumina extraction ratio reached 96.27% for the coarse bauxite residue size fraction (Sands) and 87.06% for fine BR obtained from red mud. The grade of iron (total iron in the form of iron element) in the residue can be increased to 69.55% for Sands and 58.31% for BR. The solid residues obtained after leaching were studied by XRD, XRF, TG-DTA, VSM, Mössbauer spectroscopy and SEM to evaluate the conversion and leaching mechanisms and the recovery ratio of Al from different minerals. The iron-rich residues can be used in the steel industry or as a pigment.

Steel slag is a co-product of the steelmaking industry, this material is rarely used as a binder due to its low cementitious properties. Thus, it´s believed that the alkaline activation of steel slag can enable its use as a cementitious material. This work has the objective of making a systematic bibliographic review on the theme "slag melt as a precursor in activated alkali binders". To this end, the ProKnow-C method was used for the selection and analysis of relevant research on the topic. The portfolio resulted in 71 texts, mostly journals paper. Bibliometrics showed that the country with the most publications is China and the journal with the most publications is Construction and Building Materials. The critical analysis concluded that the XRD, XRF, and compressive strength tests are the most used for the characterization of the material. It is possible to establish that there are some knowledge gaps on the subject, such as better mechanical characterization and greater production of works with dosing by the one-part method.

Li4Ti5O12 (LTO) exhibits zero-strain behavior, exceptional cycle stability, low cost, and high safety. However, it is still low in electronic and ionic conductivity. Incorporating Sn into LTO materials can increase electronic conductivity and specific capacity. However, Sn still experiences volumetric expansion during the charging/discharging process. Adding activated carbon (AC) into the LTO/Sn composite can help improve the expansion resistance and electronic conductivity. In this work, the AC was first synthesized from charcoals through the carbon activation process and mixed with LTO precursors through the sol-hydrothermal method followed by mixing with Sn through the mechanochemical process to produce LTO@AC/Sn composites. The Sn content was fixed at 15 wt.%, while the AC contents were varied at 1 wt.%, 3 wt.%, and 5 wt.%. The AC specific surface area is increased by more than 100% compared to the non-activated one. The best effects of AC on grain morphology and distribution were found in the LTO/Sn contained 3 wt.% of AC, leading to transfer resistance, ohmic resistance, specific capacity, and coulombic efficiency were found to be 48.1 Ω, 8.5 Ω, 138 mAhg-1, and near 100%, respectively. The result suggests that the LTO@AC/Sn could be a favorable anode active material in lithium-ion batteries.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

In the study, ground granulated blast furnace slag was activated with a wide variety of sodium salts to compare the effect of their pH and anion size on the hydration progress and compressive strength development of GGBFS pastes. Research was carried out on samples activated with twelve different sodium salts, cured for one year. Changes in their phase composition (XRD), loss on ignition at different temperatures, expansion and microstructure (SEM+EDS) were examined over the entire curing period. Studies have shown that the presence of sodium ions is more important than the pH of the system, as activation took place even in the case of compounds whose solutions are characterized by low pH, such as sodium tartrate or phosphate. The compressive strength of the pastes ranged from approximately 8 to 65 MPa after one year of curing.

This article deals with the possibility of partial replacement of blast furnace slag with fly ash after denitrification by the Selective Non-Catalytic Reduction (SNCR) method in alkali-activated materials. In the experiment, the basic physical-mechanical properties and durability properties were tested, the hydration reaction was monitored in a calorimeter and infrared spectroscopy was performed. Results were compared between mixtures prepared with fly ash without denitrification and also with reference mixture based only on alkali-activated blast furnace slag. The basic result is the finding, that hybrid alkali-systems with fly ash after denitrification show similar trends as hybrid alkali-systems with fly ash without denitrification. The significant effect of fly ash is manifested especially in terms of resistance to freeze-thaw. The reactions in the calorimeter show a slower development of reactions with increasing replacement of slag by fly ash. In the case of testing resistance to leaching in demineralised water, a decrease of flexural strength was found, which corresponds to the conclusions of strength testing, that long-term deposition of bodies in water causes deterioration of mechanical properties.

In recent years, several alternatives for improving the thermal comfort conditions inside buildings have been proposed. Among these alternatives, Thermally Activated Building Systems (TABS) have become of interest due to the benefits this technology brings to the building sector. The TABS are embedded in different building components and exchange heat with building envelope to improve the indoor air temperature. This review presents relevant results presented in the literature on the thermal behavior of TABS, the different types of TABS configurations, and the main parameters of TABS studied such as pipe separation, fluid inlet temperature, fluid velocity, and volumetric flow rate. The potential of TABS to improve thermal comfort conditions and provide energy savings is also discussed. Further, this study presents the different modes of application.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.