New multilayer 3D nanocomposite wear-resistant ion-plasma hard and superhard coatings Avinit [(TiN-AlN)(Mo-Cr-V-Si)]_n have been developed.The introduction of additional alloying elements (Mo, Cr, V, Si) into the Ti-Al-N coating composition, which have a high affinity for nitrogen and are capable of forming strong nitride nanoparticles in the Ti-N and Al-N layers.This makes it possible to obtain hard and superhard hardening coatings.The metallographic and tribological studies carried out indicate the prospects of the developed multicomponent multilayer nano- and microstructured Avinit coatings for increasing wear resistance and reducing friction coefficients.This paper is devoted to the development and implementation of Avinit vacuum plasma technologies for strengthening cutting and forming tools to improve tool performance.Production tests of cutting tools with Avinit's developed multilayer wear-resistant ion-plasma coatings in production conditions at many large machine-building enterprises have shown their high efficiency.In serial production, the wear resistance of tools increases by 3 to 30 times, stamps by 5 to 100 times, and parts rubbing against abrasive materials by 10 to 100 times.Avinit's vacuum plasma technologies have been successfully implemented in production in the aggregate and engine building, transport engineering, and power engineering industries.Positive experience in applying multicomponent coatings has been gained not only when applying hardening coatings to manufactured cutting tools, but also after regrinding to regrindable carbide cutting tools from domestic and foreign manufacturers.

The generation of high-quality wideband frequency sweeps presents a significant challenge, particularly in modern telecommunication, radar, and measurement systems where miniaturization is paramount. While phase-locked loops (PLLs) have become the dominant technique for signal generation, their application in broadband sweeps necessitates fractional-N operation. This, in turn, degrades phase noise and introduces unwanted spurs. This paper proposes a novel approach for broadband signal generation. By cascading two PLLs and utilizing a coaxial resonator, we achieve a high-performance oscillator that operates without the excessive fractional spurs, maintaining their level below -80 dBc across the entire frequency band. The prototype demonstrates non-degraded phase noise performance, reaching -102 dBc/Hz at 100 kHz offset and -121 dBc/Hz at 1 MHz offset for signal at 10 GHz. Despite significant frequency jumps, our design achieves lock times below 41 µs. These results, supported by theoretical analysis, validate the proposed method's effectiveness in generating low-noise broadband frequency sweeps, ideal for local oscillator applications.

A novel concept of ion separation Anisotropic Diffusion Mobility Analyser (ADMA) with Individual Ion Counter (IIC) was shown by numerical modelling to be able to separate ions with high resolution and ultra-high sensitivity. An ADMA-IIC device has been developed and tested at sheath flow rates below 40 l/min with a number of chemicals relevant to airport security and military applications. The resolving power of the ADMA was observed to be in the range of 40 to 80. These data were close to the resolution obtained in numerical modelling predictions. It is greater than or comparable with the RP of currently available on-the-market devices for airport security and other applications. It was also confirmed that the ADMA technology enables very fast detection of analytes, at least 100 times faster than ion mobility spectrometers. It was shown that Brownian diffusion can be controlled and even overpowered by generating highly anisotropic diffusion in the ADMA device. The ultimate sensitivity of single-ion detection below the ppq range has been demonstrated.

(i) Investigations of stellar systems known as wide binaries suggest that Newton’s law of gravitation breaks down at low accelerations. This can be explained by proposing a fifth force with $U(1)$ gauge symmetry, whose corresponding gauge boson is the sought for dark matter candidate. (ii) Relativistic causality (i.e. no faster than light signalling) permits nonlocal correlations stronger than those permitted by quantum mechanics. This can be explained if our universe possesses a second 4D spacetime with a signature opposite to ours. (iii) Such a fifth force, and a second spacetime, arise naturally in a recently proposed theory of unification based on an $E_8\times E_8$ symmetry. Our spacetime arises from breaking of an $SU(2)_R\times U(1)_{YDEM}$ symmetry, and the second spacetime arises from broken electroweak symmetry.

Organic solar cells are contributing extensively to the production of future large area and cost-effective sources of renewable energy with a compact environmental impact. Moreover, due to tunable optical properties of the active medium, the semi-transparent organic solar cell can be fabricated and become a promising nominee for building Integrated Photovoltaics (BIPV), vehicles, and mobile electronic devices. Therefore, three newly synthesized polymers used as were host materials for the active medium and blended with beetroot dye. Hence, based on BHJ structure two ternary systems have been constructed and utilized to fabricate semitransparent solar cells and characterized. The results show that the natural dye has a crucial impact on solar cell characteristic parameters. Consequently, large value of V_OC close to 1V were obtained for ternary systems and acceptor material named PINDOLE exhibits potentials for electron transport layer (ETL) and shows an improvement in both fill factor and device efficiency.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Due to the extraordinary mechanical properties of ultra-high-performance concrete (UHPC), the shear stirrups in UHPC beams could potentially be removed. The aim of this study is to determine the effect of beam height and steel fiber volume content on the shear behavior of non-stirrup UHPC beams under a larger shear span-depth ratio (up to 2.8). Eight beams were designed and fabricated, including six non-stirrup UHPC beams and two comparing stirrup-reinforced normal concrete (NC) beams. The experimental results demonstrated that the volume content of steel fiber could be a crucial factor affecting the ductility, cracking strength, and shear strength of non-stirrup UHPC beams and altering their failure modes. Additionally, the height of the beam had a considerable effect on its shear resistance. This study revealed that the French standard formulae were more accurate for the UHPC beams with larger shear span-depth ratios and PCI-2021 formulae greatly overestimate the shear capacity of UHPC beams with larger shear span-depth ratios. Xu’s formulae were more accurate for the steel fiber-reinforced UHPC beams with larger shear span-depth ratios.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

This paper shows that the empirical distribution of cross-sectional analyst coverage in China's stock markets follows an exponential law in a given month from 2011 to 2020. The findings hold in both the emerging (Shanghai) and the developed market (Hong Kong). Moreover, the unique distribution parameter (i.e., mean) is directly related to the amount of market-wide information. Average analyst coverage exhibits a significant negative predictive power for stock-market uncertainty, highlighting the role of security analysts in diminishing the total uncertainty. The exponential law can be derived from the maximum entropy principle (MEP). When analysts, who are constrained by average ability in generating information (i.e., the first-order moment), strive to maximize the amount of market-wide information, this objective yields the exponential distribution. Contrary to the conventional wisdom that security analysts specialize in the generation of firm-specific information, empirical findings suggest that analysts primarily produce market-wide information for 25 countries. Nevertheless, it remains unclear why cross-sectional analyst coverage reflects market-wide information, this paper provides an entropy-based explanation.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Hydrogen fuel is gaining particular attention in internal combustion engines. In addition to zero-carbon emissions, major advantages relate to its combustion characteristics, which allow significant increase in thermal efficiency under ultra-lean operation and with very low NOx levels. The ignition system is one of the main technology enablers, as it determines the capability to control ultra-lean operations, avoid backfire phenomena, or reduce the risks of abnormal combustions. The latter results from the hydrogen low ignition energy and it is associated with factors like high-temperature residuals, hot spots, and irregular spark plug discharge. ACIS gen 2-Barrier Discharge Igniter excels in accelerating the initial flame growth speed by the generation of non-equilibrium low-temperature plasma, strong ignition promoter for the combined action of kinetic and thermal effects. Moreover, its volumetric discharge facilitates combustion initiation on a wide region, in contrast to the localized ignition of traditional spark systems. In this work we present for the first time, to the best of our knowledge, experimental results showing the performance of a hydrogen engine with a low-temperature plasma discharge. Tests were conducted on a single-cylinder research engine, achieving ultra-lean conditions with cycle-to-cycle variability results below 2.5%. The analysis indicates that the H2 - BDI combined solution is capable of accelerating the evolution of the flame front compared to traditional spark plugs, leading to a significant reduction in the cycle-to-cycle variability. A meticulous adjustment of the BDI control parameters further enhances igniter performance and contributes to a deeper understanding of the innovative approach proposed in this study.

In recent years, there has been an increasing interest in adopting novel sensing technologies for the continuous monitoring of structural systems. In this respect, Micro-Electro-Mechanical System (MEMS) sensors are widely used in several applications, including Structural Health Monitoring (SHM). Thanks to their significantly lower cost, ease of installation on the structure, and lower power consumption, they enable extensive, pervasive, and battery-less monitoring systems. This paper presents an innovative high-performance device for SHM applications, based on a low-noise triaxial MEMS accelerometer, providing a guideline and insightful results about the opportunities and capabilities of these devices. Sensor nodes have been designed, developed, and calibrated to meet structural vibration monitoring and modal identification requirements. These components include a protocol for reliable command dissemination through the network and data collection, and improvements to software components for data pipelining, jitter control, and high-frequency sampling. Devices were tested in the lab using shaker excitation. Results demonstrate that MEMS-based accelerometers are a feasible solution to replace expensive piezo-based accelerometers. Deploying MEMS is promising to minimize sensor node energy consumption. Time and frequency domain analysis show that MEMS can correctly detect modal frequencies, useful parameters for damage detection. The acquired data from the test bed were used to examine the functioning of the network, data transmission, and data quality. The proposed architecture has been successfully deployed in a real case study to monitor the structural health of the Marcus Aurelius Exedra Hall within the Capitoline Museum of Rome. The performance robustness was demonstrated and the results showed that the wired sensor network provides dense and accurate vibration data for structural continuous monitoring.

Food composition data in the EMR countries are often lacking, obsolete or unreliable. The study aims to provide reliable and up-to-date nutrient data of selected food products consumed in Oman in order to evaluate consistency of nutrition labelling and update the current used food composition database. Contents of total fat, fatty acids, carbohydrates, total nitrogen, sugars and sodium were chemically analyzed in 221 foods and beverages purchased in 2022 and label and corresponding laboratory values were compared using the tolerance levels of the European Union. Food items were classified according their nutritional composition, the extent of processing and coded according FoodEx2 system. Results indicate that the nutrient values stated on a label align with the values obtained in the laboratory with the exception of a 6.3% discrepancy in TFAs content, where the reported values are higher than the appropriate reference values. The category with the highest frequency (71.5%) consisted of ultra-processed foods. In terms of inconsistencies in the nutrition claims, 5.1% of food products with claims did not comply with the statement “sugar free” or “low salt”. These findings underscore the significance of vigilant monitoring of nutritional labels as a means to implement measures that promote the well-being of consumers.

To address the issue of traditional static evaluation models being unable to comprehensively analyse the performance of ultra-supercritical coal-fired units under varying loads, we propose a dynamic comprehensive evaluation model based on the improved Criteria Importance Through Inter-criteria Correlation (CRITIC) method and Entropy Weight Method (EWM). The comprehensive performance evaluation index system of ultra-supercritical coal fired units is constructed by examining the boiler performance, turbine performance, plant power performance, environmental performance, and flexible performance of coal powered units. The CRITIC and EWM methods are used to calculate the weights of the indicators, which are then combined with the static evaluation results. Using a dynamic comprehensive evaluation model, we analysed ultra-supercritical coal-fired units, taking into account time weight. This allowed us to obtain the comprehensive dynamic real-time evaluation value of the units under different loads. The research indicates that the dynamic comprehensive evaluation model, which uses an improved CRITIC and EWM, has significant advantages in improving evaluation accuracy, weight-balanced distribution, and generality. Provides more accurate, reasonable, and reliable evaluation results for practical decision making.

(1) Background: Ultra-endurance exercise involves a high physical impact, resulting in muscle damage, inflammatory response and production of free radicals that alter the body's oxidative state. Supplementation with antioxidants, such as beetroot, may improve recovery in ultra-endurance runners. The aim of this study was to determine whether there is a correlation between the beetroot intake and the recovery of serum oxidative status, inflammatory response and muscle damage parameters after an ultra-endurance race. (2) Methods: An observational and longitudinal study was conducted by means of surveys and blood samples collected from 32 runners during the IX Penyagolosa Trails CSP® race and the two following days. The variables C-reactive protein (CRP), lactate dehydrogenase (LDH), creatine kinase (CK), the activity of the antioxidant enzymes glutathione peroxidase (GPx) and glutathione reductase (GR), as well as the oxidative damage markers malondialdehyde (MDA), carbonyl groups (CG) and loss of muscle strength using the Squat Jump test (SJ) were analyzed to discriminate whether beetroot consumption can modulate the recovery of ultra-trail runners. (3) Results: Significant differences were observed between runners who ingested beetroot and those who did not, in terms of oxidative status, specifically in serum GPx activity at 24 and 48 hours, muscle damage variables CK and LDH and in SJ test at the finish line. Therefore, the intake of supplements containing beetroot positively influences the recovery of serum oxidative status and muscle damage after ultra-endurance running.

Gallium oxide (Ga2O3) is an emerging wide bandgap semiconductor promising a wide range of important applications. However, mass production of high-quality crystalline Ga2O3 still suffers from limitations associated with poor reproducibility and low efficiency. Low-temperature grown amorphous Ga2O3 demonstrates comparable performance with its crystalline counterparts. Lanthanide Er3+-doped Ga2O3 (Ga2O3: Er) possesses great potential for developing light-emitting devices, photodetectors and optical waveguides. The host circumstance can exert a crystal field around the lanthanide dopants and strongly influence their photoluminescence properties. Here we present a systematical study of the impact of amorphous-to-crystalline transition on the upconversion photoluminescence in Ga2O3: Er thin films. Through controlling the growth temperature of Ga2O3: Er films, the upconversion luminescence of as-grown thin films are strongly enhanced over 100 times. Moreover, the variation of photoluminescence reflects the amorphous-to-crystalline transformation of the Ga2O3: Er thin films. These results will aid further design of favorable optoelectronic devices integrated with lanthanide-doped Ga2O3 thin films.

This paper reviews several techniques, including analytical theories and real frequency techniques, to design ultra-wideband impedance matching networks for low-power applications. The comparison of solutions obtained using the simplified real frequency technique to the published solution using Chebyshev filter theory is demonstrated.

Pachychoroid neovasculopathy (PNV) is a pachychoroid-spectrum disease. As blood circulation throughout the choroid may be involved in PNV pathogenesis, analysis using ultra-wide-field (UWF) fundus imaging is crucial. We evaluated choroidal thickness after half-fluence photodynamic therapy (PDT) combined with intravitreal aflibercept injection for PNV using UWF swept-source optical coherence tomography. Seventeen eyes with PNV that underwent half-fluence PDT with adjuvant single intravitreal aflibercept injection were analyzed. To compare choroidal thicknesses in the central and peripheral choroids, we set subfields <3, <9, and 9–18 mm from the fovea. The <9- and 9–18-mm subfields were divided into four quadrants. Choroidal thickness in each subfield decreased significantly after half-fluence PDT (P<0.001); this reduction was more pronounced in the central area. We also investigated the relationship between the dominant side of the deep choroidal veins that harbor choroidal vein efflux from the macula. When choroidal thickness in the supratemporal and infratemporal 9x9-mm subfields were evaluated, the ratio of choroidal thickness reduction was not significantly different between the dominant and non-dominant sides. The dominant side was not associated with the extent of choroidal thickness reduction in PNV. In conclusion, half-fluence PDT caused thinning of the entire choroid, especially in the central area, in PNV.

Estimating the infection risks in indoor environments comprises the assessment of the behavior of virus-laden aerosols, i.e. spreading, mixing, removal by air purifiers etc. A promising experimental approach is based on using non-hazardous surrogate aerosols of similar size, e.g. salt particles, to mimic the virus aerosol behavior. This manuscript addresses the issue how a successful transfer of such experiments can be accomplished. Corresponding experiments in two very different environments, a large community hall and a seminar room, with optional use of air purifiers in various constellations were conducted. While high particle concentrations are advantageous in terms of avoiding influence of background aerosol concentrations, it is shown that appropriate consideration of aggregation and settling are vital to theoretically describe the experimentally determined course of particle concentrations. A corresponding model equation for a well-mixed situation is derived and the required parameters are thoroughly determined in separate experiments independently. It is demonstrated that clean air delivery rates (CADR) of air purifiers determined with this approach may differ substantially from common approaches not explicitly taking into account aggregation.

Actually wide excision is recommended after the primary excision of any cutaneous melanomas. The definition of the margins of wide excision indicated by the guidelines has remained unchanged over the years, although the reported indications derived from fairly dated studies, in which melanomas tend to be thicker or in advanced stages at diagnosis. These indications may no longer be current; especially in those patients affected by in situ or thin melanoma, exposing patients to a possible overtreatment. A retrospective observational study was conducted in patients who had undergone surgery for melanoma in a single institution. In a univariate model a melanoma-positive wide excision resulted related with a worst progression free survival (PFS); but this association was not confirmed in the multivariable model. Moreover, logistic model were applied to estimate the probability to find a metastasis after wide local excision (WLE) in relation to demographic data of patients and histologic information of the melanoma. Results testified that the Breslow thickness was the only factor associated with the increase of the risk to found metastases in the WLE area. The ROC curve testified that the optimum cut-off value to differentiate patients with respect those without a tumor-positive wide excision, was a Breslow thickness of 2.31mm in women, and 2.4mm in men.

In precision grinding of hard and brittle materials, coarse-grained diamond grinding wheels are increasingly favored for their efficiency and contour accuracy. However, challenges in dressing these grinding wheels have hindered their widespread adoption. In this paper, the effects of dressing parameters on the surface profile and morphological characteristics of electroplated coarse-grained diamond were studied, thereby optimizing the dressing accuracy and dressing efficiency of the coarse-grained diamond grinding wheel. Models for the surface morphology of the large-grained diamond grinding wheel and its grinding surface were established. With a focus on optimizing dressing accuracy, we explored how the grain’s protruding height post-dressing affects the surface morphology of both the diamond grinding wheel and the grinding surface. The model’s accuracy was verified by electroplated coarse-grained diamond grinding wheel grinding experiments with different grain protrusion heights, and the causes of surface morphology formation were analyzed based on morphological characteristic parameters such as surface roughness and surface height difference. The results showed that compared with the undressed grinding wheel, the surface roughness Sa and Sq of the workpiece by the dressing wheel are reduced by 97.75%−99.77% and 97.57%−99.73%, respectively. Precision dressing enables the surface roughness of the electroplated coarse-grained diamond grinding wheel to reach nanometer levels, enhancing its feasibility and application potential.

Mercury (Hg) pollution not only poses a threat to the environment but also adversely affects the growth and development of plants, with potential repercussions for animals and humans through bioaccumulation in the food chain. Maize, a crucial source of food, industrial materials, and livestock feed, requires special attention in understanding the genetic factors influencing mercury accumulation. Developing maize varieties with low mercury accumulation is vital for both maize production and human health. In this study, a comprehensive genome-wide association study (GWAS) was conducted using an enlarged SNP panel comprising 1.25 million single nucleotide polymorphisms (SNPs) in 230 maize inbred lines across three environments. The analysis identified 111 significant SNPs within 78 quantitative trait loci (QTL), involving 169 candidate genes under the Q model. Compared to the previous study, the increased marker density and optimized statistical model led to the discovery of 74 additional QTL, demonstrating improved statistical power. Gene Ontology (GO) enrichment analysis revealed that most genes participate in arsenate reduction and stress responses. Notably, GRMZM2G440968, associated with the significant SNP chr6.S_155668107 of axis tissue, encodes a cysteine proteinase inhibitor, suggesting its potential role in alleviating Hg toxicity by inhibiting cysteine. Haplotype analyses provided further insights, indicating that lines carrying hap3 exhibited the lowest mercury content compared to other haplotypes. In summary, our study significantly enhances the statistical power of GWAS, identifying additional genes related to mercury accumulation and metabolism. These findings offer valuable insights into unraveling the genetic basis of mercury content in maize and contribute to the development of maize varieties with low mercury accumulation.

This article explores the implementation of high accuracy GPS denied Ad-Hoc localization. There is little research on Ad-Hock UWB-enabled localization systems with mobile and stationary nodes. This work aims to demonstrate the localization of bicycle-modeled robots in a non-static environment through a mesh network of mobile, stationary robots and ultra-wideband sensors. The non-static environment adds a layer of complexity when actors can enter and exit the node’s field of view. The method starts with an initial localization step where each unmanned ground vehicle (UGV) uses the surrounding, available anchors to derive an initial local or, if possible, global position estimate. The initial localization uses a simplified implementation of the iterative multi-iteration Ad-Hoc Localization System (AHLos). This estimate was refined using an unscented Kalman filter (UKF) following a constant turn rate and velocity magnitude model (CTRV). The UKF fuses the robot’s odometry and the range measurements from the Decawave ultra-wideband receivers stationed on the network nodes. Through this position estimation stage, the robot broadcasts to its neighbors its estimated position to help the others further improve their localization estimates and localize themselves. This wave-like cycle of nodes helping to localize each other allows the network to act as a mobile Ad-Hoc localization network.

In the autonomous navigation of mobile robots, precise positioning is crucial. In forest environments with weak satellite signals or in sites disturbed by complex environments, satellite positioning accuracy has difficulty in meeting the requirements of autonomous navigation positioning accuracy for robots. This article proposes a binocular vision SLAM/UWB tightly coupled localization method. The core of this algorithm is based on an Extended Kalman Filter (EKF), which utilizes the displacement increment output by binocular vision ORB-SLAM and the positioning coordinates calculated via UWB positioning as measurement information to achieve data fusion. The research utilized the constructed experimental platform to collect images and UWB ranging data in outdoor environments and experimentally validated the combined positioning method. The experimental results show that this algorithm outperforms the use of the individual UWB or visual SLAM localization methods in terms of positioning accuracy. Compared with traditional single positioning algorithms, this algorithm exhibits better practicality and stability, and can effectively suppress the impact of UWB non line of sight errors. The average error under normal line of sight conditions is 0.058 m, the root mean square error (RMSE) is 0.080, and the average error under non-line-of-sight conditions is 0.081 m, with an RMSE of 0.084. There is no significant jump or drift. Through the tightly coupled processing of binocular vision SLAM and UWB positioning, more reliable and accurate mobile robot positioning can be achieved, providing a useful reference for the autonomous navigation of mobile robots in complex environments.

Wide-field (WF) retinal imaging is becoming a standard diagnostic tool for diseases involving the retinal periphery. Technological progress elicited the advent of wide-field optical coherence tomography (WF-OCT) and WF-OCT angiography (WF-OCTA) examinations. This review presents the results of studies that analyzed the implementation of these procedures in clinical practice and refers to them as traditional and ultra-wide-field fluorescein angiography (UWF-FA). The PUBMED search was performed using the terms WF-OCT OR WF-OCTA OR UWF-FA AND the specific clinical entity, including diabetic retinopathy (DR), retinal vein occlusion (RVO), Coats disease, peripheral retinal telangiectasia, peripheral retinal degeneration, lattice degeneration, and posterior vitreous detachment. The analysis only included the studies in which the analyzed field of view for the OCT or OCTA exam was larger than 55 degrees. The evaluation of the extracted studies indicates that WF imaging with OCT and OCTA provides substantial information on retinal disorders involving the retinal periphery. Vascular diseases, such as DR or RVO, can be reliably evaluated using WF-OCTA with results superior to standard-field fluorescein angiography. Nevertheless, UWF-FA provides a larger field of view and still has advantages over WF-OCTA concerning the evaluation of areas of non-perfusion and peripheral neovascularization. Detailed information on the vascular morphology of peripheral changes should be obtained via WF-OCTA, not angiographic examinations. WF-OCT can serve as a valuable tool for the detection and evaluation of vitreoretinal traction, posterior vitreous detachment, and peripheral retinal degeneration, and guide therapeutic decisions on a patient’s eligibility for surgical procedures.

The reflection and transmission spectra of a metamaterial formed by omega-shaped elements with pre-calculated optimal parameters on a silicon substrate have been recorded in the terahertz range at oblique incidence for the s- and p- polarizations of the incident wave. The spectra were interpreted within the dipole radiation theory of electromagnetic waves. Both measurement results and analysis provide evidence sup-porting the presence of a pronounced polarization anisotropy impact in the reflection and transmission of the metamaterial. The potential of these materials to be utilized in the development of devices that control the polarization properties of THz radiation across a wide spectral range is examined.

The development of modern genomic tools has sped up the breeding program of food crops. More recently, genomic resources are being developed for tropical forages and will be key resources for developing climate resilient high yielding forage varieties. In this study, we present a genome-wide association study for biomass yield and feed quality traits in buffel grass (Cenchrus ciliaris L. aka Pennisetum ciliare L.,). Genome-wide markers generated using the DArTSeq platform and mapped onto the reference genome of Setaria italica were used for the genome-wide association study. The results revealed several markers associated with biomass yield and feed quality traits. A total of 78 marker trait associations were identified with R2 values ranging from 0.138 to 0.236. The marker trait associations were distributed across different chromosomes. Of these associations, the most marker trait associations (23) were observed on Chr9, followed by Chr5 with 12. The fewest number of marker trait associations were observed on Chr4 with 2. In terms of traits, 17 markers were associated with biomass yield, 24 with crude protein, 26 with TDN, 14 with ADF, 10 with NDF and six with DMI. Twenty of the identified markers were associated with at least two traits. The identified marker trait associations provide a useful genomic resource for future improvement and breeding of buffel grass.

The main aim of this work is to present a step-by-step procedure to model and analyze the power loss distribution of three-level Gallium Nitride (GaN) inverters. It has been applied to three distinct three-phase three-levels voltage source inverters utilized in electric traction drives: Active Neutral Point Clamped, Neutral Point Clamped and T-Type Neutral Point Clamped. The proposed analytical power loss modelling, combined to an equivalent representation of the electrical machine demonstrated to be a viable solution to achieve a time-saving and low computational burden simulation platform, leading to satisfying accuracy results. This has been confirmed by comparing the results carried out from the simulations of a 110kW permanent magnet synchronous motor drive and those determined by considering a simplified circuital representation based on the proposed analytical power loss modelling.

in this article, an ultra-wideband traveling wave antenna with antipodal topology is proposed. The proposed design is realized on an economical substrate with minimum thickness. The proposed design offers an ultra-wide bandwidth of 26 to 40 GHz, translating to 42%. The dimensions of the antenna are 20mm x10mm x 0.5mm indicating an electrically compact structure. The proposed antenna offers high front to back ratio of at least 10dB across the bandwidth of operation. The forward gain of the antenna varies from 4 to 7dBi in the afore-mentioned band. The pattern integrity is maintained throughout the band. The antenna is fabricated using the commercial photolithography process. A mutli-step topology of the antennas is also proposed for wide angular coverage. The coverage is greater than 150º with mutual coupling less than 25dB. These performance metrics is achieved with a very small footprint. Simulated and experimental results are presented in this paper.

Genome-wide association studies (GWAS) have successfully revealed many disease-associated genetic variants. For a case-control study, the adequate power of an association test can be achieved with a large sample size, although genotyping large samples is expensive. A cost‐effective strategy to boost power is to integrate external control samples with publicly available genotyped data. However, the naïve integration of external controls may inflate the type I error rates if ignoring the systematic differences (batch effect) between studies, such as the differences in sequencing platforms, genotype calling procedures, population stratification, and so forth. To account for the batch effect, we propose an approach by integrating External Controls into the Association Test by Regression Calibration (iECAT-RC) in case-control association studies. Extensive simulation studies show that iECAT-RC not only can control type I error rates but also can boost statistical power in all models. We also apply iECAT-RC to the UK Biobank data for M72 Fibroblastic disorders by considering genotype calling as the batch effect. Four SNPs associated with Fibroblastic disorders have been detected by iECAT-RC and the other two comparison methods. However, our method has a higher probability of identifying these significant SNPs in the scenario of an unbalanced case-control association study.

Control of Tropical Theileriosis, a tick-borne disease with a strong impact on cattle breeding, can be facilitated by using marker-assisted selection in breeding programs. Genome-wide association studies (GWAS) using high-density arrays are extremely important for the ongoing process of identifying genomic variants associated with resistance to Theileria annulata infection. In this work, Single Nucleotide Polymorphisms (SNPs) were analyzed in the Portuguese autochthonous cattle breeds Alentejana and Mertolenga. In total, 14 SNPs suggestive of significance (p ≤ 10-4) were identified for Alentejana cattle and 20 SNPs for Mertolenga cattle. The genomic regions around these SNPs were further investigated for annotated genes and Quantitative trait loci (QTLs) previously described by other authors. Regarding the Alentejana breed, the MAP3K1, CMTM7, SSFA2, and ATG13 genes are located near suggestive SNPs and appear as candidate genes for resistance to Tropical Theileriosis, considering its action the immune response and resistance to other diseases. On the other hand, in the Mertolenga breed, the UOX gene is also a candidate gene due to its apparent link to the pathogenesis of the disease. These results may represent a first step towards the possibility of including genetic markers for resistance to Tropical Theileriosis in current breed selection programs.

The design of binders plays a pivotal role in achieving enduring high power in lithium-ion batteries (LIBs) and extending their overall lifespan. This review underscores the indispensable characteristics that a binder must possess when utilized in LIBs, considering factors such as electrochemical, thermal, and dispersion stability, compatibility with electrolytes, solubility in solvents, mechanical properties, and conductivity. In the case of anode materials, binders with robust mechanical properties and elasticity are imperative to uphold electrode integrity, par-ticularly in materials experiencing substantial volume changes. For cathode materials, the se-lection of a binder hinges on the crystal structure of the cathode material. Other vital consid-erations in binder design encompass cost-effectiveness, adhesion, processability, and envi-ronmental friendliness. Incorporating low-cost, eco-friendly, and biodegradable polymers can contribute significantly to sustainable battery development. This review serves as an invaluable resource for comprehending the prerequisites of binder design in high-performance LIBs and offers insights into binder selection for diverse electrode materials. The findings and principles articulated in this review can be extrapolated to other advanced battery systems, charting a course for the development of next-generation batteries characterized by enhanced perfor-mance and sustainability.

In the rapidly evolving landscape of wireless communication, each successive generation of networks has achieved significant technological leaps, profoundly transforming the way we connect and interact. From the analog simplicity of 1G to the digital prowess of 5G, the journey of mobile networks has been marked by constant innovation and escalating demands for faster, more reliable, and more efficient communication systems. As 5G becomes a global reality, laying the foundation for an interconnected world, the quest for even more advanced networks leads us to the threshold of the sixth-generation (6G) era. This paper presents a hierarchical exploration of 6G networks, poised at the forefront of the next revolution in mobile wireless technology. This study delves into the technological advancements that underpin the need for 6G, examining its key features, benefits, and the key enabling technologies. We dissect the intricacies of cutting-edge innovations like terahertz communication, ultra-massive MIMO, artificial intelligence (AI), machine learning, quantum communication, and re-configurable intelligent surfaces. Through a meticulous analysis, we evaluate the strengths, weaknesses, and state-of-the-art research in these areas, offering a wider view of the current progress and potential applications of 6G networks. Central to our discussion is the transformative role of AI in shaping the future of 6G networks. By integrating AI and machine learning, 6G networks are expected to offer unprecedented capabilities, from enhanced mobile broadband to groundbreaking applications in areas like smart cities and autonomous systems. This integration heralds a new era of intelligent, self-optimizing networks that promise to redefine the parameters of connectivity and digital interaction. This paper also addresses critical challenges in the deployment of 6G, from technological hurdles to regulatory concerns, providing a holistic assessment of potential barriers. By highlighting the interplay between 6G and AI technologies, this study not only maps out the current landscape but also lights the path forward in this rapidly evolving domain. This paper aims to be a cornerstone resource, providing essential insights, addressing unresolved research questions, and stimulating further investigation into the multifaceted realm of 6G networks. By highlighting the synergy between 6G and AI(Artificial Intelligence) technologies, we aim to illuminate the path forward in this rapidly evolving field.

Smart farm is a technology that greatly helps improve the productivity and quality of crops and is being actively introduced into indoor environments such as green houses. However, it has not yet been distributed to field-grown crops. The main reason is that, unlike indoor environments, it is very difficult to collect sensor data for monitoring the growth environment of crops in open fields where weather conditions change significantly and power supply is difficult. Additionally, because various sensors are used, the data formats of the devices are different, making it difficult to process. This paper presents a field crop growth environment monitoring and big data analysis system. The proposed system first solves power supply and data communication problems using solar power generation and LPWA technology. Additionally, based on the oneM2M architecture, data from various sensors is transmitted to the server using standardized technology. The transmitted data is stored and managed on the server as big data, and can be used to predict the production and quality of field-grown crops and take appropriate measures. The proposed system is expected to create an environment optimized for the growth of field crops and help prevent and manage diseases.

Background: Genome-wide association studies (GWAS) have shed light on various complex diseases and traits, by detecting more than 400,000 associated genetic loci. This number is expected to drastically increase because of the use of novel artificial intelligence methods offering new ways to study the effects of variants. Deep learning using artificial neural networks (ANN) is a sub-field of artificial intelligence, which simulates how the human brain learns. We aimed at assessing the potential of deep learning in human genetic studies of Alzheimer’s Disease (AD) and how these compare to the traditional statistical methods used in GWAS, by simultaneously testing the two approaches on the same dataset, while discovering new genetic loci associated to AD. Methods: To address this aim, phenotypic and genome-wide SNP data from the UK Biobank was analysed on a binary outcome, AD diagnosis, in two different data balance options, of one-to-one and one-to-two case-control datasets, using 2,764 cases vs 2,764 controls and 5,528 controls respectively matched on gender, age, ethnicity, PC1-20 and genotyping array. Genetic data handling and GWAS were performed using PLINK, whereas neural networks were trained using GenNet, a new ANN tool, with the same datasets, separated into training (60%), validation (20%) and test (20%) sets. Neural network layers were determined using biological knowledge, by annotating SNPs to genes and genes to AD related pathways, using ANNOVAR annotations followed by GeneSCF and KEGG. Results: Significant associations were detected between four SNPs linked to two different genes and AD for the 1 to 1 case-control study design and six SNPs linked to four different genes for the 1 to 2 case-control study design by using PLINK. All identified regions have been previously associated to AD. GenNet identified twelve SNPs on seven genes to be associated with AD, all with biological plausibility, achieving an AUC of 0.80 when using three biologically determined layers and 0.73 when using two layers at the neural networks. No common top SNPs were identified between the machine learning and GWAS models. Conclusion: This is one of the first studies attempting to compare the traditional GWAS to more sophisticated state-of-art methods for understanding the genetic architecture of complex phenotypes using the same dataset. More systematic comparisons with such approaches on real data are needed to enable best practises for machine learning in the analysis of genome-wide genetic data.

China is facing the development requirements of the dual carbon goal and the construction needs of resilient cities. Currently, high-strength composite structural systems are a feasible solution, but their research and application in the construction field are insufficient, especially for the combination forms of concrete above C100 and steel above Q550. In response to this issue, this paper proposes a new high-performance structural system, namely the composite frame - high-strength steel plate wall core tube resilient structure system, which includes high-strength steel plate (Q550) - ultra-high strength concrete (C100) shear walls, replaceable energy dissipation coupling beams, and composite frames. Taking a 200 meter building as an example, this paper designs and establishes calculation models for a conventional reinforced concrete frame-core tube structure and a high-performance structure based on PKPM software, and establishes elastoplastic analysis models for both based on SAUSAGE software, and then conducts dynamic elastoplastic time history analysis and seismic resilience assessment of structures under design basis earthquakes (DBEs), maximum considered earthquake (MCEs) and extremely rare earthquakes (EREs). Research has shown that compared to conventional structures, new high-performance structures can effectively reduce the size of shear walls, reduce the self-weight of the structure, and enhance the space for building use; The story drift ratio has higher redundancy than specification limits, lower plastic damage and overall stiffness degradation of the structure, and better seismic performance; The seismic resilience has significantly improved, especially in the case of casualties, which can better ensure the safety of people's lives and property.

Plant protein phosphatase 2Cs (PP2Cs) serve as negative regulators of protein kinase cascades activated in different processes and play important roles in plant development and abiotic-stress-mediated signaling pathways. In this study, a genome-wide study was conducted on the CqPP2C gene family. A total of putative 117 CqPP2C genes were identified. Comprehensive analyses of physical and chemical feature, chromosome localization and subcellular localization were conducted. According to phylogenetic analysis, CqPP2Cs were divided into 13 subfamilies. CqPP2Cs in the same subfamily had similar gene structure, conserved motif and all the CqPP2C proteins had the type 2C phosphatase domains. Gene duplication revealed that segmental duplication was the major driving force for CqPP2Cs expansion and all duplicated CqPP2Cs evolved from purifying selection. The expression of CqPP2Cs in various tissues under different abiotic stresses was analyzed using RNA-seq data. The results revealed that CqPP2C genes were involved in regulating development and stress responses of quinoa. Real-time quantitative reverse transcription PCR (qRT-PCR) analysis of six CqPP2C genes in subfamily A revealed that they were up-regulated or down-regulated under salt and drought treatments. Furthermore, the results of yeast two-hybrid assays revealed that subfamily A CqPP2Cs interacted not only with subclass III CqSnRK2s, but also with subclass II CqSnRK2s. Subfamily A CqPP2Cs could interact with CqSnRK2s in different combinations and intensities to respond to various biological processes and stresses. Overall, our results will be useful for understanding the functions of CqPP2C in regulating ABA signals and responding to abiotic stress.

Machine learning, including deep learning, reinforcement learning, and generative artificial intelligence are revolutionising every area of our lives when data is made available. With the help of these methods, we can decipher information from larger datasets while addressing the complex nature of biological systems in a more efficient way. Although machine learning methods have been introduced to human genetic epidemiological research as early as 2004, those were never used to their full capacity. In this review, we outline some of the main applications of machine learning to assigning human genetic loci to health outcomes. We summarise widely used methods and discuss their advantages and challenges. We also identify several tools, such as Combi, GenNet and GMSTool, specifically designed to integrate these methods for hypothesis-free analysis of genetic variation data. We elaborate on the additional value and limitations of these tools from a geneticist’s perspective. Finally, we discuss the fast-moving field of foundation models and large multi-modal omics biobank initiatives.

Although Sugarcane bagasse ash (SCBA) has good cementitious property, previous researchers have primarily aimed to improve the mechanical performance of conventional concrete or cement-based composites. Research is lacking on ultra-high performance concrete (UHPC), especially regarding tensile self-sensing properties. This paper aimed to comprehensively evaluate the SCBA effect on the UHPC’s mechanical, electrical, and tensile self-sensing properties. The results showed that SCBA below the critical incorporation concentration (CIC) improved the UHPC’s mechanical properties compared to steel fibers alone. Furthermore, adding 3.0wt% SCBA remarkably enhanced the UHPC mechanical properties where the compressive, flexural, and tensile strengths increased by 13.1%, 17.4%, and 20.6%, respectively. The SCBA content of 0.3wt% achieved the maximum UHPC electrical resistivity since values smaller or greater than this content decreased the resistivity. The SCBA-enhanced UHPC showed better tensile stress-sensing performance than UHPC without SCBA due to improved linearity and reversibility, lower hysteresis, higher sensitivity, and superior repeatability. UHPC with 0.3wt% SCBA achieved the best linearity, while UHPC with 0.9wt% SCBA showed the highest sensitivity, lowest hysteresis, and best repeatability. Overall, the content of 0.9wt% SCBA is the best in improving the overall mechanical, electrical, and tensile self-sensing performance.

Ultra high molecular weight polyethylene (UHMWPE) is a thermoplastic high-performance polymer in high demand for biomedicine, ship and machine building, anthropomorphic robots and smart prostheses. Highly oriented UHMWPE fibers possess record specific strength and may also be used for the fabrication of self-reinforced PE-PE composites (SRPEC). The temperature evolution study of the small-angle X-ray scattering (SAXS) signature of the supramolecular structure of UHMWPE can help reveal their important role in the mechanism of the shape memory effect in SRPEC. The laboratory SAXS–WAXS beamline XEUSS 3.0 was used for in situ studies of the nanostructure parameters in unidirectional SRPEC. Namely, the radius of gyration and the dimensionality factor were extracted from 2D SAXS patterns using several fitting algorithms. Significant changes of these parameters occurred in temperature ranges that correspond to the initiation of the shape memory effect and melting. The relationship between the material anisotropy and 2D SAXS patterns are discussed in the context of the supramolecular structure evolution.

Multiple Gateways (GWs) provide network connectivity to Internet of Things (IoT) sensors in a Wide Area Network (WAN). The End Nodes (ENs) can connect to any GW by discovering and acquiring its periodic beacons. This provides GW diversity and hence improves coverage. If the GWs are within vicinity to each other, and they keep sending periodic beacons to be discovered, the result is interference and collisions. In this study, the impact of such intra-network interference is analyzed to determine the maximum number of GWs that can co-exist within a given urban neighborhood. The paper shows the relationship between beacon collisions and the resulting packet loss rates in a given urban environment. The expected collision rates are calculated for the Medium Access Control (MAC) layer. The eventual packet loss rates are calculated with the MAC and Physical (PHY) layers combined. For this purpose, a new co-channel interference model is presented. The model calculates the average Carrier to Interference ratio (C/I) averaged across all the colliding events. It takes into account the partial overlap durations and the relative power of each colliding signal. The model shows that a collision does not always cause a packet loss. Packet losses occur if there is a collision and if the C/I is below a threshold. The performance evaluation is presented using a combination of analytical and simulation methods. The analytical methods provide the theoretical foundation, and have been used to validate the simulation results. Furthermore, the system models are developed from experimental data obtained from measurements with real hardware. Numerical results are provided with a low bit rate Gaussian Frequency Shift Keying (GFSK) modulation at the PHY layer, which is derived from the IEEE 802.15.4 standard specification. This paper provides guidance on selecting the right GFSK modulation parameters for such low bit-rate and narrow bandwidth IoT applications. The analysis and simulation results show that larger beacon intervals help in reducing beacon loss rates, at the cost of larger beacon acquisition latency. On the flip side, the gateway discovery latency reduces with increasing GW density thanks to abundance of beacons.

Advanced high-strength steels (AHSS) have a wide range of applications in equipment safety and lightweight design, and enhancing the strength of AHSS to the ultra-high level of 2 GPa is currently a key focus. In this study, a new process of thermo-mechanical control process followed by direct quenching and partitioning (TMCP-DQP) is developed based on Fe-0.4C-1Mn-0.6Si (wt.%) low-alloy steel, and the effects of microstructure evolution on mechanical properties under TMCP-DQP process and conventional hot rolled quenched and tempered process (HR-QT) are comparatively studied. The results show that the TMCP-DQP process not only shortened the processing steps but also achieved outstanding comprehensive mechanical properties. The TMCP-DQP steel exhibits a tensile strength of 2.23 GPa, accompanied by 11.9% elongation and a Brinell hardness of 624 HBW, with an impact toughness of 28.5 J at -20 ℃. In contrast, the HR-QT steel exhibits tensile strengths ranging from 2.16 GPa to 1.7 GPa and elongations between 5.2% and 12.2%. The microstructure of TMCP-DQP steel primarily consists of lath martensite, containing thin-film retained austenite (RA), nanoscale rod-shaped carbides, and a minor number of nanoscale twins. The volume fraction of RA reaches 7.7%, with an average carbon content of 7.1 at.% measured by three-dimensional atom probe tomography (3DAP). Compared to the HR-QT process, the TMCP-DQP process results in finer microstructure, with a prior austenite grain (PAG) size of 11.91 μm, forming packets and blocks with widths of 5.12 μm and 1.63 μm. The TMCP-DQP process achieves the ultra-high strength of low-alloy steel through the synergistic effects of grain refinement, dislocation strengthening, and precipitation strengthening. The dynamic partitioning stage stabilizes the RA through carbon enrichment, while the relaxation stage reduces a small portion of the dislocations generated by thermal deformation, and the self-tempering stage eliminates internal stresses, all guaranteeing considerable ductility and toughness. The TMCP-DQP process may offer a means for industries to streamline their manufacturing processes and provide a technological reference for producing 2.2 GPa grade AHSS.

In this perspective article, we ponder topographical enhancements of artificial neural networks. In our recent paper in JMLR, we proved a quasi-equivalence between the network width and depth and also discussed the power of intra-links, which can be viewed as network height. In 1982, Hopfield published a network to model human associative memory, which contains many loops for dynamic evolution toward fixed points. Based on noising-denoising loops, diffusion models are recently developed to enable Bayesian modeling and inference with big data. Furthermore, we envision development of multi-AI-agent systems through “netware” engineering as a quantum leap of software engineering for emergent behaviors and autonomous AI at individual and population levels. We believe that the novel use of links and loops in space and time via multi-scale coupling would catalyze the next-generation neural networks.

This research paper investigates ultra-wideband (UWB) localization systems by focusing on the use of average filter (AVG), Kalman filter (KF), and extended Kalman filter (EKF) algorithms, as well as a novel integrated filtering method that incorporates low-pass filter (LPF) into AVG, KF, and EKF. The study aims to improve localization loss in indoor environments using a TurtleBot robot equipped with a camera to observe ground truth positions. To evaluate the effectiveness of the proposed algorithms, a comprehensive comparison of the raw and filtered data with the camera-based ground truth observations is performed. Quantitative analyses of the results, including max, min, max-min, and mean error, are performed to evaluate the localization performance of the algorithms and the integrated filtering method. The results reveal that the integrated filtering method has performed better accuracy in comparison with existing methods.

Gibberella ear rot (GER) caused by Fusarium graminearum (teleomorph Gibberella zeae) is one of the most destructive diseases in maize that severely reduces grain yield and contaminates several potential mycotoxins. However, few efforts had been devoted to dissect the genetic basis of maize GER resistance. In the present study, a genome-wide association study (GWAS) was conducted in a maize association panel consisting of 303 diverse inbred lines. The phenotypes of GER severity were evaluated using kernel bioassay across multiple time points in the laboratory. Then, three models including fixed and random model circulating probability unification model (FarmCPU), general linear model (GLM) and mixed linear model (MLM), were conducted simultaneously in GWAS to identify single-nucleotide polymorphisms (SNPs) significantly associated with GER resistance. A total of four individual significant association SNPs with the phenotypic variation explained (PVE) ranging from 3.51 to 6.42% were obtained. Interestingly, the peak SNP (PUT-163a-71443302-3341) with the greatest PVE value, was co-localized in all models. Subsequently, 12 putative genes were captured from the peak SNP that several of these genes were directly or indirectly involved in disease resistance. Overall, these findings contribute to understand the complex plant-pathogen interactions in maize GER resistance. The regions and genes identified herein provide a list of candidate targets for further investigation, in addition to the kernel bioassay that can be used for evaluating and selecting elite germplasm resources with GER resistance in maize.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

Carbon nanomaterial is widely used in structural health monitoring due to the advantage of sensitivity and good mechanical properties. This study presents a novel approach employing carbon nanocomposite materials (CNM) to characterize deformation and damage evolution in physical modelling. As the primary measurement method, the CNM is used to investigate the deformation characteristics of a 200-400 m thick sandstone bed at a 1 km deep longwall mine. The sandstone unit is identified as an ultra-thick key stratum (UTKS), with its thicknesses varying across different mining panels of the UTKS. The results of CNM monitoring show that the UTKS remains stable even after a consecutive excavation of 900 m in width. This stability impedes the upward propagation of overlying strata failure, leading to minimal surface subsidence. The study demonstrates the huge potential of CNM in the mining area, which can be useful for investigating material damage in physical modelling studies. The findings suggest that the cumulative extraction width in individual mining areas of the mine should be controlled to avoid a sudden collapse of the UTKS, and that special attention should be paid to where the UTKS's thickness changes substantially. The substantial variation in UTKS thickness significantly impacts the pattern of overburden subsidence.

Recently, smart mobility intelligent traffic services have become a critical task in Intelligent Transportation Systems (ITS). This involves not only the use of advanced sensors and controllers but also the ability to respond to real-time traffic situations at intersections, alleviate congestion, and generate policies to prevent traffic jams. DRL (Deep Reinforcement Learning) provides a natural framework for processing tasks. In DRL, each intersection can control itself and coordinate with neighbors to achieve optimal network-wide policies. However, comparing approaches remains a challenging task due to the existence of numerous possible configurations. This research performs a critical comparison of various traffic controllers found in the literature. It demonstrates that using a nonlinear approximator for coordination mechanisms and enhancing observability at each intersection are key performance drivers.

Hispanics are disproportionately affected by low rates of physical activity and high rates of chronic diseases. Hispanics generally and Mexican Americans specifically are underrepresented in research on physical activity and its impact on mental well-being. Some community-based interventions have been effective in increasing physical activity among Hispanics. This study examined data from a sample of low-income Hispanic participants in free community exercise classes to characterize the association between self-reported frequency of exercise class attendance, intensity of physical activity, and participant well-being. As part of two cross-sectional samples recruited from a stratified random sample of community exercise classes, 302 participants completed a questionnaire consisting of a modified version of the Godin-Shephard Leisure-Time Exercise Questionnaire (LTEQ) and the Mental Health Continuum Short Form (MHC-SF). Adjusted binary logistic regression analyses indicated that those who achieve moderate and strenuous self-reported physical activity have 130% higher odds (p = 0.0422) of positive mental well-being after adjustment for age, attendance, and self-reported health. This study provides evidence that physical activity intensity and time are associated with flourishing mental health among Hispanics. The study provides insight into the planning and development of community-based physical activity programming tailored to low-income populations.

In recent, Chae found that, at weak gravitational acceleration g_N≲10⁻⁹ms⁻², the observed orbit of the wide binary stars is not accordant with current theory of binary star. Here, we present, this finding should be an observational evidence for that Newtonian theory of orbit perturbation is still valid in galactic scale.

In this work, we present a transceiver front-end in SiGe BiCMOS technology that can provide an ultra-wide bandwidth of 100 GHz at millimeter-wave frequencies. The front-end employs a novel configuration for low-loss distribution of broadband generated pulses as well as coherent spatial combining of received pulses. This leads to the realization of a fully integrated ultra-high-resolution imaging chip for biomedical applications. We realized an ultra-wide imaging bandwidth of 100 GHz by the integration of two adjacent, disjointed frequency sub-bands of 10–50 GHz and 50–110 GHz respectively. The transceiver front-end is capable of both transmit (TX) and receive (RX) operations. This is a key building-block for a scalable system in which a unit cell is repeated in the X and Y directions resulting in less power and area consumption. The imaging elements were designed and fabricated in Global Foundry 130-nm SiGe 8XP BiCMOS process technology.

Abstract：Objective: To compare the effects of fermentation on the chemical composition of Gastrodia Tuder Halimasch Powder, and to provide a basis for the processing, processing and clinical application of this medicinal material. Methods: UHPLC-Q-Orbitrap HRMS was used to identify compound structure by comparing excimer ions, characteristic fragment ions and reference substances, and referring to relevant literature and database search. The main differential components were screened by orthogonal partial least squares-discriminant analysis (OPLS-DA), and the differential components were quantitatively studied by high performance liquid chromatography, and the differences in the types and contents of chemical components before and after fermentation were compared. Results: A total of 77 compounds were identified or preliminarily derived after fermentation, including 21 terpenes, 18 organic acids, 9 flavonoids, 7 nucleosides, 6 amides, 4 amino acids, 2 pyrrolidone derivatives, 2 sterols, 2 alkaloids and 6 others.Through high performance liquid chromatography, it was found that the content of daidzein genistein and ergosterol was significantly increased after fermentation, and a new component ergosterol was produced. Compared with Gastrodia Tuder Halimasch Powder before fermentation, the content of genistin and other components was significantly reduced, and there may be a process of genistin conversion to genistein.Conclusion: The fermentation process will have a certain influence on the types and contents of the chemical components of Gastrodia Tuder Halimasch Powder, and ergosterol, genistein and .daidzein may be the main pharmacodynamic components, which can provide a useful reference for the clinical rational application, quality control and mechanism of action of Gastrodia Tuder Halimasch Powder.

Plant cell and tissue culture has been a crucial component of efforts to enhance crops and advance plant biotechnology ever since the beginning of the XX century when Hildebrand discovered the theory of totipotency – a somatic plant cell still has the capacity to develop into every cell that makes up a whole plant. Further standardization of the techniques for use in crop improvement has resulted from the original interest with the creation of the numerous plant tissue culture techniques through the various advancement. The most important approach used in plant tissue culture is the cultivation of differentiated tissue that results in the development of an undifferentiated mass of parenchymatous cells and their subsequent differentiation by organogenesis or somatic embryogenesis. This has been playing a significant role in the creation of virus-free seedlings and fast clonal multiplication, and it is also a crucial component in transgenic' regeneration. Additionally, cell cultures with a variety of mutations emerging in it offers chances to enhance crops. For the purpose of identifying homozygous recombinants in a single generation, haploid cell culture offers an additional benefit. Wide hybridization and the embryo rescue procedure have helped to produce haploid embryos and homozygous lines of doubled haploids which are difficult and time consuming to produce using traditional methods. Developed haploid embryos from the male gametophyte, carried out in cultures of immature anthers or isolated microspores, are referred to as androgenesis and could be the most efficient way to create lines of doubled haploids. The cell cultures also offer the chance to extract a variety of beneficial biochemicals. Induction of mutations in cultured cells and tissue in vitro to produce beneficial cultivars and manipulation of the centromere-specific histone CENH3 also become possible in recent years. Compared to traditional methods, in vitro cultures offer a number of both scientific and practical advantageous for scientists and plant breeders. However, the usefulness of individual methods should be examined by analyzing their advantages and disadvantages. When it comes to oat (Avena sativa L.) the efficient method of plant regeneration is still missing compared to the most common cereals, possibly because this cereal is known as recalcitrant for in vitro culture. An effort has been made to provide a succinct overview of the various in vitro techniques utilized or potentially involved in breeding of oat (Avena sativa L.) in this review. The present work aims to summarize the crucial methods of A. sativa cultivation under tissue culture conditions with a focus on the progress that has been made in biotechnological techniques which are used in breeding of this species.

FLASH-RT represents a novel therapeutic radiation modality that holds remarkable potential for mitigating radiation therapy’s adverse side effects. This cutting-edge technology allows for the sparing of healthy tissue while precisely targeting cancerous cells by administering an ultra-high dose-rates of typically between 10 and 30 Gy in less than a few hundred milliseconds. FLASH-RT has demonstrated impressive results in small-animal models, prompting scientists to adapt and advance existing technologies to make it a viable treatment option for humans. However, producing the ultra-high-dose-rate radiation required for the therapy remains a significant challenge. Several radiation sources, such as very high energy electrons (VHEEs), low energy electrons, x-rays, and protons, have been studied for their ability to deliver the necessary dose. Among them, FLASH-x-ray has gained the most attention owing to its capacity to penetrate deeply seated tumours. Despite the complexity of the process, the potential advantages of FLASH-RT make it an exciting area of research. To achieve the FLASH effect, high-frequency, pulsed irradiated accelerator technology can be employed. Sparing healthy tissue, it may allow for more aggressive and effective cancer treatments, leading to a better quality of life for patients. Ongoing research and development will be necessary to refine and optimize this approach to radiation therapy.

Objective: To evaluate the existing meta-analytic evidence of associations between exposure to ultra-processed foods, as defined by the Nova food classification system, and adverse health outcomes. Design: Systematic umbrella review of existing meta-analyses. Data Sources: MEDLINE, PsycINFO, Embase, and the Cochrane Database of Systematic Reviews, as well as manually searching reference lists from 2009 to June 2023. Inclusion Criteria: Systematic reviews and meta-analyses of cohort, case-control, and/or cross-sectional study designs that evaluated the associations between exposure to ultra-processed foods and adverse health outcomes in humans across the lifespan. Results: The search identified 45 unique pooled analyses, including 13 dose-response and 32 non-dose-response associations (n=9,888,373). Overall, direct associations were found between exposure to ultra-processed foods and 32 (71%) health outcome domains spanning cardiometabolic, gastrointestinal, and respiratory conditions, cancer, mental health, and mortality. Based on a pre-specified evidence classification criteria, convincing evidence (Class I) supported direct associations between greater ultra-processed food exposure and higher risks of incident cardiovascular disease-related mortality (RR: 1.50; 95%CIs: 1.37 to 1.63), type two diabetes (dose-response RR: 1.12; 95%CIs: 1.11 to 1.13), and depressive outcomes (HR: 1.21; 95%CIs: 1.16 to 1.28), as well as higher risks of prevalent anxiety outcomes (OR: 1.48; 95%CIs: 1.37 to 1.59) and combined common mental disorder outcomes (OR: 1.53; 95%CIs: 1.43 to 1.63). Highly suggestive (Class II) evidence indicated that greater exposure to ultra-processed foods was directly associated with higher risks of incident all-cause mortality (RR: 1.21; 95%CIs: 1.15 to 1.27), heart disease-related mortality (dose-response HR: 1.66; 95%CIs: 1.51 to 1.84), and type two diabetes (OR: 1.40; 95%CIs: 1.23 to 1.59), together with higher risks of prevalent obesity (OR: 1.55; 95%CIs: 1.36 to 1.77), adverse sleep-related outcomes (OR: 1.41; 95%CIs: 1.24 to 1.60), and wheezing (RR: 1.40; 95%CIs: 1.27 to 1.55). Out of the remaining 34 pooled analyses, 21 were graded as suggestive or weak strength (Class III-IV) and 13 were graded as no evidence (Class V). Using the GRADE framework, 22 pooled analyses were rated as "Low" quality, with 19 rated as "Very Low” and four rated as "Moderate" quality. Conclusions: Higher exposure to ultra-processed food was associated with a greater risk of adverse health outcomes, especially cardiometabolic, common mental disorder, and mortality outcomes. These findings provide a rationale to evaluate the effectiveness of using population-based measures to target and reduce dietary exposure to ultra-processed foods for improved human health. Systematic Review Registration: PROSPERO CRD42023412732.

Background: In this secondary analysis of the Supporting the Modification of Lifestyle In Lowered Emotional States (SMILES) randomised controlled trial, we investigated if the beneficial effects of a dietary intervention on clinical depression were driven, in part, by reducing the consumption of foods classified as ultra-processed.Methods: The SMILES trial enrolled 67 adults with major depressive disorder, randomly assigning them to either a 12-week modified Mediterranean dietary intervention or a social support control. Our analysis included 44 participants with non-missing dietary data and at least one valid Montgomery–Åsberg Depression Rating Scale (MADRS) assessment at 12 weeks of follow-up. The Nova food classification system was used to estimate the proportion of ultra-processed foods in the overall diet (percentage of grams) based on data from seven-day food diaries. We fitted linear regression models under blinded conditions to determine whether ultra-processed food intake-change from baseline to 12 weeks moderated the dietary intervention effects on depressive symptoms. We estimated mean differences in depressive symptoms along with ninety-five per cent confidence intervals (95%CIs).Results: For participants in the dietary intervention, there was an additional 2.5-point improvement in MADRS scores for each 10% reduction in the dietary share of ultra-processed foods compared to participants in the control group (between-group mean differences in depressive symptoms: −2.46, 95%CIs −4.71 to −0.20, p=0.039, η _p ² of 0.10).Conclusions: These preliminary findings suggest that the therapeutic benefit of a dietary intervention for depression may stem, at least in part, from reductions in the dietary share of ultra-processed foods.

This paper proposes a compact wideband split ring resonator (SRR) based C-shaped antenna for 5G new radio (NR) band n258 millimeter wave (mm-Wave). The proposed antenna covers a wideband frequency range from 24.1 GHz to 28.3 GHz with a reflection coefficient below -10 dB. Stubs are used at each C-shaped element for impedance matching of the antenna. The proposed antenna comprises SRRs with stubs to increase the bandwidth and gain simultaneously for better performance in mm-Wave applications. A simple SRR structure is modeled to function as a reactive impedance surface with inductive property for frequencies less than 30.2 GHz. The proposed antenna realizes an impedance bandwidth of 16.1% and covers a wideband of 4.2 GHz (24.1 GHz -28.3 GHz). The use of stubs and SRR has improved the performance of the proposed antenna at mm-Wave frequencies. Specifically, the deployment of the SRR is able to produce an improved gain for the overall direction of the antenna. The simulation and measured results agree well and maintain a 7.49 dBi gain with a bandwidth of 4.2 GHz. An average efficiency of 90% can be attained in the operating range of the antenna. The designed antenna is applicable for 5G NR Band n258.

Background: The level of food processing has gained interest for a potential determinant of human health. The aim of this study was to assess the relation between level of food processing and prostate cancer severity. Methods: A sample of 120 consecutive patients were examined for their dietary habits assessed through validated food frequency questionnaires, their dietary intake of food groups categorized according to the NOVA classification, and the severity of prostate cancer according to the European Association of Urology (EAU) guidelines groups risk. Uni- and multivariate logistic regression analyses were performed to test the association between the variables of interest. Results: Individuals reporting higher consumption of unprocessed/minimally processed foods were less likely to have worse prostate cancer severity than lower consumers in the energy-adjusted model [odds ratio (OR) = 0.38, 95% confidence interval (CI): 1.17-0.84, P = 0.017 and OR = 0.33, 95% CI: 0.12-0.91, P = 0.032 for medium/high vs. low grade and high vs. medium/low grade prostate cancers, respectively); however, after adjusted for potential confounding factors, the association was no more significant (Table 4). A borderline association was also found between higher consumption of UPF and worse prostate cancer severity in the energy-adjusted model (OR = 2.11, 95% CI: 0.998-4.44; P = 0.051), but again the association was no more significant after adjusting for the other covariates. Conclusions: The level of food processing seems not to be independently associated with prostate cancer severity, while potentially related to other factors that need further investigation.

Age-related macular degeneration (AMD) causes visual impairment in individuals >50 years of age. However, no study has investigated AMD using ultra-wide-field swept-source optical co-herence tomography (UWF SS-OCT). We aimed to evaluate central and peripheral choroidal thickness using UWF SS-OCT and compare AMD subtypes. We included 75 eyes of patients with typical AMD (tAMD), 56 with polypoidal choroidal vasculopathy (PCV), 29 with pachychoroid neovasculopathy (PNV), and 12 with retinal angiomatous proliferation (RAP). To compare cho-roidal thicknesses in the central and peripheral choroids, we established subfields of <3 mm, <9 mm, and 9–18 mm from the fovea. PNV patients were significantly younger than those with tAMD (P=0.01). The choroidal thicknesses of PNV were significantly greater than that of tAMD in all subfields (P<0.01) and choroidal thickness significantly correlated with age and axial length in all subfields (P<0.05). Even after adjusting for age and axial length, the choroidal thickness in PNV was significantly greater than that in tAMD (P<0.05). In addition, the ratio of the posterior < 9 mm to peripheral 9–18 mm choroidal thickness in PNV was significantly greater than that in tAMD (P<0.01). A thickened choroid in PNV was more pronounced in the posterior choroid than in the periphery.

Fatigue-related subchondral bone injury of the third metacarpal/ metatarsal (McIII/ MtIII) bone is a common cause of wastage and welfare concern in racehorses. Better understanding of bone health and strength would improve animal welfare and be of benefit for the racing industry. Porosity index (PI) of bone is an indirect measure of osseous pore size and number and is therefore an interesting indicator of bone strength. MRI of compact bone using traditional methods even with short echo times fails to generate enough signal to assess bone architecture as the water protons are tightly bound. Ultrashort echo time (UTE) sequences aim to increase the amount of signal detected in the equine McIII/MtIII condyle. Cadaver specimens were imaged using a novel dual-echo UTE MRI technique and PI was calculated and validated against quantitative CT-derived bone mineral density (BMD). BMD and PI are inversely correlated in the equine distal Mc/ MtIII with a mean r value of -0.29. The r value is significantly different between fore- and hindlimbs. Further work is needed to assess how correlation patterns behave in different areas of the bone and to evaluate PI in horses with and without clinically relevant stress injury.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

In light of the current situation where no testing equipment is available for measuring thermal deformation of objects, this paper proposes a novel method for accurate and precise measurement. The method overcomes the limitations of previous approaches that relied on pitch angle. By utilizing the principle of biplane multiple reflections, a bivariate laser spot displacement analysis algorithm is devised to attain highly precise measurements of bivariate angles. Additionally, a temperature gradient comparison algorithm is introduced to calculate the indicator test results under specific temperature conditions. To validate the effectiveness and reliability of this method, a testing system is constructed and utilized. The results demonstrate that the thermal deformation angle change test achieves an impressive accuracy of 0.015″ and a rate of thermal deformation angle change of 0.3247″/°C. These values are in close agreement with the previously simulated analysis result of 0.359″/°C, with only a relative error of 9.55%. Therefore, the test results confirm the efficacy and reliability of this testing method along with the feasibility of the algorithm processing.

The sensitivity of exercise ECG is marginally sufficient for detection of mild reduction of coronary blood flow in patients with early coronary atherosclerosis. Here we describe the application of new technique of ECG registration/analysis – ultrahigh resolution ECG (UHR ECG) – for early detection of myocardial ischemia (MIS). The utility of UHR ECG vs. conventional ECG (C ECG) was tested in anesthetized rats and pigs. Transmural MIS was induced in rats by the ligation of the left coronary artery (CA). In pigs, subendocardial ischemia of variable extent was produced by stepwise inflation of balloon within the right CA causing 25-100% reduction of its lumen. In rats, a reduction in power spectral density (PSD) in high-frequency (HF) channel of UHR ECG was registered at 60 s after ischemia (power 0.81±0.14 vs. 1.25±0.12 mW at baseline, p<0.01). This was not accompanied by any ST segment elevation on C ECG. In pigs, PSD in HF channel of UHR ECG was significantly decreased at 25% reduction of CA lumen, while ST segment on C ECG remained unchanged. In conclusion, UHR ECG enabled earlier detection of transmural MIS compared to C ECG. PSD in HF-channel of UHR ECG demonstrated greater sensitivity in the settings of subendocardial ischemia.

Breakage and damage of fiber optic cable fibers seriously affect the normal operation of fiber optic networks and it is important to quickly and accurately determine the type and location of faults when they occur. The advantages of wavelet transform in singular signal detection and signal filtering are used to analyze Optical Time Domain Reflectometer (OTDR) curve signal and the fault detection method of fiber communication link with no relay and large span in high altitude area is given, which realizes the accurate detection and location of optical fiber communication link fault events under strong noise. The theoretical analysis is basically consistent with the experimental data. The accuracy of optical fiber fault location has been greatly improved in performance. The method has been directly applied to the field detection of ultra-long optical fiber links in high altitude areas, which has certain significance for the future real-time monitoring of optical fiber cables.

Keywords: Baseband, GeoSurf Constellation, Interference, Linear Distortions, Passband, Time Delay, Rain attenuation, Synthetic Storm Technique, ultra–wideband.

DEXTER (Detection of EXplosives and firearms to counter TERrorism) is a project funded by NATO’s Science for Peace and Security (SPS) program with the goal of developing an integrated system capable of remotely and accurately detecting explosives and firearms in public places without impeding the flow of pedestrians. The active microwave component of the DEXTER project is referred to as MIC (Microwave Imaging Curtain), supported by the French SGDSN (General Secretariat of Defense and National Security), and utilizes a radar system capable of generating 3D images in real time to address non-checkpoint detection of explosives and fire-arms. The project, led by the ONERA (France), is based on a radar imaging system developed by the Fraunhofer FHR institute, using a MIMO architecture with an Ultra Wide-Band waveform. Although high-resolution 3D microwave imaging is already being used in expensive body scanners to detect firearms concealed under clothing, MIC's innovative approach lies in utilizing a high-resolution 3D imaging device that can detect larger dangerous objects carried by moving individuals at a longer range, in addition to providing discrete detection in pedestrian flow. Automatic detection and classification of these dangerous objects is carried out on 3D radar im-ages using a deep-learning network. This paper will outline the project's objectives and constraints, as well as the design, architecture, and performance of the final system. Additionally, it will present real-time imaging results ob-tained during a live demonstration in a relevant environment.

A cell filtration platform that affords accurate size separation and minimizes fouling was developed. The platform features an ultra-thin porous membrane (UPM) filter, a pumping head for backflushing (PHB), and cell size measurement (CSM) software. The UPM chip is an ultrathin free-standing membrane with a large window area of 0.68 mm2, a pore diameter of 5 to 9 μm, and a thickness of less than 0.9 μm. The PHB prevents filter fouling. The CSM software analyzes the size distributions of the supernatants and subnatants of isolated cells and presents the data visually. The D99 particle size of cells of the chronic myeloid leukemia (CML) line K562 decreased from 22.2 to 17.5 μm after passage through a 5-μm filter. K562 cells could be separated by careful selection of the pore size; the recovery rate attained 91.3%. The method was compared to conventional blocking models by evaluating the mean square errors (MSEs) between the measured and calculated filtering volumes. The filtering rate was fitted by a linear regression model with a significance that exceeded 0.99 based on the R2 value. The platform can be used to separate various soft biomaterials and affords excellent stability during filtration.

Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

The straightness error of guideway is one of the key indicators of ultra-precision machine, which plays an important role in the machining accuracy of work-piece. In order to measure straightness error of long distance ultra-precision guideway accurately, a splicing measurement for straightness error of guideway using high-precision flat mirror and displacement sensor was proposed in this paper, and the data splicing processing algorithm based on coordinate transformation was studied. Then comparative experiments on splicing measurement and direct measurement of straightness error were carried out on a hydrostatic guideway grinder. The maximum difference between the two measurements was about 0.3μm, which was far less than the straightness error of 5.8μm. The experiment demonstrated the correctness of the proposed splicing measurement method and data processing algorithm. To suppress the influence of straightness error on machining accuracy, a straightness error compensation algorithm based on error rotation transformation and vertical axis position correction was proposed, and the grinding experiment of a plane optics with size of 1400mm×500mm was carried out, whose flatness error after grinding was about 2.98μm. The straightness error of the grinding machine had been well suppressed.

Silicon-based photodetectors, as low-cost and environmentally friendly optical sensors, are attractive. Also, their compatibility with complementary metal-oxide-semiconductor (CMOS) technology is advantageous for the development of silicon photonics systems. However, extending optical responsivity of silicon-based photodetectors to the mid-infrared (mid-IR) wavelength range remains challenging. In developing mid-IR infrared Schottky detectors, nanoscale metals are critical. Nonetheless, one key factor is the Fermi level pinning effect at the metal/silicon interface and the presence of metal-induced gap states (MIGS). Here, we demonstrate the utilization of the passivated surface layer on semiconductor materials as an insulating material in metal-insulator-semiconductor (MIS) contacts to mitigate the Fermi level pinning effect. The removal of Fermi level pinning effectively reduces the Schottky barrier height by 12.5% to 16%. The demonstrated devices exhibit a high responsivity of up to 234 μA/W at a wavelength of 2 μm, 48.2 μA/W at 3 μm, and 1.75 μA/W at 6 μm. The corresponding detectivities at 2 and 3 μm are 1.17×10^8 cm Hz^1/2 W^-1 and 2.41×10^7 cm Hz^1/2 W^-1, respectively. The expanded sensing wavelength range contributes to the application development of future silicon photonics integration platforms.

HER2-low and ultra-low breast cancer (BC) have been recently proposed as new subcategories of HER2 BC, re-considering the immunohistochemical negative score of 0, 1+ or score of 2+/in situ hybridization (ISH) negative phenotype. In the present review we have outlined the needed criteria to exactly distinguish HER2 low and ultra-low BC. Recent clinical trials have demonstrated significant clinical benefits of novel HER2 directing antibody-drug conjugates (ADCs) in treating these group sof tumors. In particular, Trastuzumab-deruxtecan (T-Dxd), a HER2-directing ADC has been recently approved by the U.S. Food and Drug Administration as the first targeted therapy to treat HER2-low BC. Furthermore, ongoing trials, such as the DESTINY-Breast06, are currently evaluating ADCs in patients with HER2-ultra low BC. Finally we hope that new guidelines may help to codify HER2 low and ultra-low BC, increasing our knowledge of tumor biology and improving a targetable new therapeutical treatment.

Ultra-large cold-water pipes (CWP) may present structural instability phenomenon under complex and variable operating conditions, and the current theoretical analysis rarely takes into account the influence of multiple key parameters at the same time, resulting in some errors between the prediction results and the actual deformation behavior of the pipe. Considering this issue, this paper establishes a computational analysis model of the mechanical performance of the CWP based on the Euler-Bernoulli beam theory, considering the effect of waves, the clump weight at the bottom, internal flow and sea current, and gives a time-dependent solution of the mechanical response of the pipe with the action of multiple key parameters using the differential quadrature method (DQM). Additionally, the correctness and validity of the theoretical model are well verified by comparing the numerical solution with the theoretical results. Finally, to study the effects of operating conditions on the mechanical response of the pipe, the effects of waves, the clump weight, internal flow and sea current on the lateral deflection and maximum bending moment of the pipeline are discussed based on numerical simulation and orthogonal experimental method. The results show that changing the wave strength and internal flow velocity has little effect on the lateral deflection of the CWP, and the clump weight at the bottom can effectively suppress the lateral deflection of the pipeline, but increasing the current velocity can significantly increase the lateral deflection of the pipeline, which can lead to the instability of the pipe. Nevertheless, the effects of waves, the clump weight, internal flow and sea current on the maximum bending moment of the pipeline are basically the same, all of them increase sharply at first, and then decrease gradually until they level off, and the differences in the effects are mainly reflected in the different locations of the pipe sections. This paper suggests the design guidance of CWP in aspect of dynamic response depending on the operating condition.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

Middle East region experiences a high prevalence of hypovitaminosis D, yet most genetic studies on Vitamin D have focused on European populations. Furthermore, there is a lack of research on the genomic risk factors affecting the elderly population, who are more susceptible to health burden. We investigated the genetic determinants of 25-hydroxyvitamin D levels in elderly Lebanese individuals (n=199) through a whole exome-based genome-wide association study. We identified new loci with suggestive evidence of an association with Vitamin D levels, including rs141064014 in the MGAM gene (P-value of 4.40 × 10−06) and rs7036592 in PHF2 (P-value of 8.43 × 10−06). A meta-analysis of the Lebanese data and the largest European genome-wide association study confirmed consistence replication of numerous variants, including rs2725405 in SLC38A10 (P-value of 3.73 x 10-08). Despite the lower performance of European-derived polygenic risk scores compared to the European estimations, it still effectively predicted Vitamin D deficiency among elderly Lebanese individuals. Our findings provide novel insights into the genetic mechanisms of Vitamin D deficiency in Middle Eastern elderly populations, facilitating the development of personalized approaches for more effective management of hypovitaminosis D. Additionally, we demonstrated that whole exome-based genome-wide association study is an effective method for identifying genetic components associated with phenotypes.

The introduction of stool as a readily obtainable sample and the recently developed simple-one-step (SOS) stool processing method offer an opportunity for TB diagnosis in children. We conducted this study at secondary health facilities in Ethiopia which are the first level referral facilities for childhood TB diagnosis and treatment with the aim to determine if stool-based TB diagnosis can be performed with reasonable level of concordance with sputum tests in using Xpert MTB/RIF Ultra. Eligible children 0-14 years with presumptive pulmonary TB were asked to provide stools in addition to routinely requested sputum samples. We computed Cohen’s kappa statistic in SPSS to determine the level of agreement between stool and sputum test results. Of the 373 children included in the study, 61% were &lt;5 years of age and 56% were male. Thirty-six children (9.7%) were diagnosed with TB and all started treatment. The rate of concordance between stool and sputum was high with kappa value of 0.83 (P&lt;0.001). There were more Xpert ultra positive test results on stool (n=27 (7.2%)) than on sputum/NGA (n=23 (6.2%)). Laboratories in secondary hospitals can perform stool-based TB diagnosis in children with high concordance between stool and sputum test results reaffirming the applicability of the SOS method.

With the vast amount of goods being shipped around the world, there is a need to track and manage various types of assets, particularly shipping containers. Logistics industries dealing with small facilities, shipments, equipment, and vehicles must be tracked. There are many applied asset tracking systems such as Radio-Frequency Identification (RFID), Bluetooth Low Energy (BLE) Beacon, and Long-Range Radio (LoRa). This paper presents these systems and focuses on locating assets using LoRaWAN technology, which has a positive impact on the responsive and sustainable cities in Egypt. IoT-based Long Range (LoRa) is a low-power, wide-area communication technology that uses radio frequencies to transmit data over long distances. The extended range, low power consumption, low maintenance, and the ability to store location data when the end node that needs to connect to the asset is out of the gateway's coverage make LoRa a good choice for developing asset-tracking applications. This paper introduces a real-time tracking experiment as a result of a project implementation, whose goals are aligned with industry, innovation, and infrastructure and Sustainable Cities and Communities, the Sustainable Development Goals (SDGs) No. 9 and 11.

More people around the world now have obesity than suffer from starvation thanks to our modern food system. Agriculture was transformed over the 20^th century by a variety of technological advancements that relied heavily on fossil fuels. In the United States of America, government policies and economic incentives led to surplus production of cheap inputs to processed food industries that produced a wide variety of heavily marketed, convenient, rewarding, timesaving, and relatively inexpensive ultra-processed foods. The energy available in the United States food supply increased much more than population needs, albeit with large inequities in food distribution and nutrition security. While most of the rise in per capita food availability during the late 20^th and early 21^st centuries in the United States resulted in increased food waste, a variety of mechanisms have been proposed by which changes in the increasingly ultra-processed food environment resulted in excess energy intake disproportionately in people genetically susceptible to obesity. As populations continue to grow, substantial investments in coordinated nutrition and agricultural research are needed to transform our current food system to one that relies less on fossil fuels, preserves biodiversity, ensures environmental health, and provides equitable access to affordable, safe, and nutritious food that reduces the prevalence of chronic diseases like obesity.

Japanese apricot (Prunus mume) is a culturally and economically important fruit tree in East Asia. ‘Nanko’, the primary cultivar of the Japanese apricot well known in Japan, usually suffers from scab, a disease caused by Venturia carpophila. Scab results in the development of black spots on the fruit surface, which considerably reduces its commercial value. Despite being an economic concern for Japanese apricot, there have been few reports on the phenotypic variation in scab resistance/susceptibility, the underlying genetic factors, and the development of DNA markers. Therefore, in this study, we performed a comprehensive trait analysis for scab resistance and susceptibility for four years and conducted a genome-wide association study (GWAS) to identify the associated loci. The results showed that significant GWAS peaks were detected in 2017 and 2018. Promising candidate gene encoding domains associated with disease resistance were found at the nine single-nucleotide polymorphisms (SNPs) identified in 2017 and 2018. These SNPs were thought to be associated with scab susceptibility of ‘Nanko’ lineages. These findings shed light on the mechanisms of scab resistance in P. mume and will assist future breeding programs to improve scab resistance in ‘Nanko’ lineages.

Ningxiang pig is renowned breed for its exceptional meat quality, but it possesses suboptimal carcass traits. To elucidate the genetic architecture of meat quality and carcass traits in Ningxiang pigs, we assessed heritability and executed a genome-wide association study (GWAS) concerning carcass length, backfat thickness, meat color parameters (L.LD, a.LD, b.LD), and pH at two postmortem intervals (45 minutes and 24 hours) within a Ningxiang pig population. Heritability estimates ranged from moderate to high (0.30 ~ 0.80) for carcass traits and from low to high (0.11 ~ 0.48) for meat quality traits. We identified 21 significant SNPs, the majority of which were situated within previously documented QTL regions. Furthermore, the HMGA1 gene emerged as a pleiotropic gene correlated with carcass length and backfat thickness. The ADGRF1, FKBP5, and PRIM2 genes were associated with carcass length, while the NIPBL gene was linked to backfat thickness. These genes hold potential for use in selective breeding programs targeting carcass traits in Ningxiang pigs.

The purpose of this project was to demonstrate the potential of converting an existing internal combustion engine for hydrogen operation at relatively low cost and to optimize the combustion process for ultra-low NOx emissions. The conversion has been carried out on a 450cc naturally aspirated single cylinder engine. The first baseline measurements and setup have shown lower NOx emissions than the baseline gasoline engine (without catalytic converter) for similar power output and engine efficiency. Further optimization of the combustion process allowed to achieve Euro VI and (latest European Commission proposal) Euro VII heavy-duty NOx limits without exhaust gas aftertreatment system (EATS) in steady state conditions. The concept is very promising and the knowledge gained should allow for further optimization to achieve near zero NOx emissions at high engine efficiency and power output with supercharging. It should also allow an efficient conversion of other engine types for different applications. In particular, a project with the aim to convert a heavy duty 6 cylinder engine intended for public transport buses has started. It follows a feasibility study which has shown the competitiveness of the hydrogen engine for this application.

A printed Vivaldi antenna that is optically transparent, ultra-wideband (UWB), and reconfigurable has been developed, fabricated, and tested at millimeter wave frequencies. It covers a broad frequency range of 20-30 GHz by using three PIN diodes. The diodes control the current flow to direct the beam of the antenna. The results of numerical simulations and measurements match at millimeter wave frequencies. The design of this antenna is unique as it allows for a reduction in size and ease of integration while also providing the ability to change the radiation pattern by up to 300 degrees, making it suitable for 5G and 6G communications. Additionally, this antenna can also be useful for RF applications that require dynamic switching of radiation patterns and cognitive radio.

Age-related Macular Degeneration (AMD) is the major cause of elders’ vision loss, early screening and treatment are the most efficient way to reduce the rate of blindness. AI-based methods based on ophthalmic images play great potential for AMD diagnosis. However, low levels of accuracy, robustness, and explainability are challenges for AI approaches applied in clinics. Thus, this study proposed a multi-type of data source fusion method and a multi-model fusion approach for AMD detection. Typical unsupervised (Hierarchical Clustering and K-Means), typical supervised (SVM, VGG-16, and ResNet) methods, and proposed methods (multi-source data fusion-based method and multi-model fusion-based approach) are compared based on Optical Coherence Tomography (OCT), Fundus Autofluorescence (FAF), regular color fundus photography (CFP) and Ultra-Wide field Fundus (UWF) images. Data preprocessing and enhancements of each type of data are discussed. A feature extraction based on unsupervised ML models, feature combination and normalization, and multi-layer perception (MLP) algorithm are involved in the proposed multi-source data fusion-based method. Supervised ML and DL models and a voting mechanism are involved in the multi-model fusion-based approach. Findings show that the proposed methods present a high performance of accuracy and robustness. A real-world UWF database is involved from Shenzhen Aier Hospital. Practical and theoretical contributions are delivered. A reference value for medical diagnosis based on multiple digital images is contributed.

Liquid biopsy is a rapidly emerging field which involves the minimal/non-invasive assessment of signature somatic mutations through analysis of circulating tumor DNA (ctDNA) shed by tumor cells in bodily fluids. The broad, unmet need for liquid biopsy lung cancer detection is the lack of multiplex platform that can detect a mutation panel of lung cancer genes using minimum amount of sample, especially for ultra-short ctDNA (usctDNA). Here we developed a non-PCR and non-NGS-based single droplet based multiplexing microsensor technology “Electric Field-Induced Released and Measurement (EFIRM) Liquid Biopsy” (m-eLB) for lung can-cer-associated usctDNA. The m-eLB provides multiplexable assessment of usctDNA within a single droplet of biofluid in only one well of micro-electrodes, as each electrode coated with dif-ferent probes for the ctDNA. In this m-eLB prototype, it demonstrates accuracy for 3 tyrosine ki-nase inhibitor related EGFR target sequences in synthetic nucleotides. The accuracy for the multi-plexing assay has an AUC of 0.98 for L858R, Ex19del, AUC of 0.94 for Ex19 deletion and AUC of 0.93 for T790M. By combining the 3 EGFR assay together, the AUC was 0.97 for the multiplexing assay.

Laser energy per unit surface, necessary to trigger the material removal, decreases with the pulse shortening becoming the pulse-time independent in the sub-picosecond range. These pulses are shorter the electron-to-ion energy transfer time and electronic heat conduction time minimizing the energy losses. The electrons receiving the energy larger than the threshold, drag the ions off the surface in the mode of electrostatic ablation. We show that the pulse shorter than the ion period (Shorter-the-Limit (StL)) ejects conduction electrons with the energy larger than the work function (from a metal) leaving the bare ions immobile in a few atomic layers. The electrons emission is followed by the bare ion’s explosion, ablation, and THz radiation from expanding plasma. We compare this phenomenon to the classic photo effect, nanocluster Coulomb explosions, show differences and consider possibilities for detecting the new mode of ablation experimentally by emitted THz radiation and consider applications of high-precision nano-machining with this low intensity irradiation.

Advancement in biotechnology and genomics research have promoted access to DNA markers and their use in breeding programs. Genome-wide association study (GWAS), Genomic selection (GS) and Marker-Assisted Selection (MAS) are some of the applications of DNA markers in plant breeding. Researchers have suggested combining these individual applications for better selection accuracies. This study examines the potential advantages of incorporating GWAS-results into MAS and GS as well as the validity of the different methods for combining these approaches. From this study, it was concluded that number of QTNs have greater effects on prediction accuracies compared to heritability estimates. Also, the increase in prediction accuracy from the invalid method of incorporating GWAS results into GS and MAS model is similar to results recorded with using the valid approach. However, greater difference may be observed in another scenario which can lead to spurious results when used to make breeding decisions.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

The accumulation of steel slag and other industrial solid wastes has caused serious environmental pollution and resource waste. The resource utilization of steel slag is imminent. In this paper, alkali activated materials ultra-high performance concrete (AAM-UHPC) was prepared by replacing GGBFS powder with different proportions of steel slag powder, and its workability, mechanical properties, curing condition, microstructure, and pore structure were investigated. The results illustrate that the incorporation of steel slag powder can significantly delay the setting time and improve the flowability of AAM-UHPC, making it possible for engineering applications. The mechanical properties of AAM-UHPC showed a tendency to increase and then decrease with the increase of steel slag dosing, and reached the best performance at 30% dosage of steel slag. The maximum compressive strength and flexural strength are 157.1 MPa and 16.32 MPa, respectively. High temperature steam or hot water curing at early age was beneficial to the strength development of AAM-UHPC, but continuous high temperature hot and humid curing would lead to strength inversion. When the dosage of steel slag is 30%, the average pore diameter of the matrix is only 8.43nm, and the appropriate steel slag dosage can reduce the heat of hydration and refine the pore size distribution, making the matrix more dense.

The PLM concept implies the use of heterogeneous information resources at different stages of the product life cycle, the joint work of which allows you to effectively solve the problems of product quality and various costs. According to the principle of isomorphism of regularities of complex systems, an effective PLM system must have these regularities. Unfortunately, this principle is not often fundamental when designing PLM systems. The purpose of the work is to show, using a simple example, the principles of development, operation and use of an educational multi-agent PLM system, the main purpose of which is to study and research these regularities in the life cycle of a special threaded connection. The multi-agent approach to the development of a PLM system provides the necessary prerequisites for the emergence of system-wide regularities in it. The parallel work of agents is implemented using the actor model and the Ray Python-package. Agents for the logical inference of knowledge base facts, CAD/FEA/CAM/SCADA agents, agents for optimization by various methods, and other agents have been developed. Open source software was used to develop the system. Each agent has relatively simple behavior, implemented by its rule function, and can interact with other agents. The system can work in interactive mode with the user or in automatic mode according to a simple algorithm: the rule functions of all agents are executed until at least one of them returns a value other than None. Examples of the operation of the system are given and such system-wide regularities as emergence, historicity and self-organization are demonstrated in it.

Due to the global warming and dynamic changes in pathogenic virulence, leaf rust caused by Puccinia triticina has greatly expanded its epidermic region and become a severe threat to global wheat production. Genetic bases of wheat resistance to leaf rust mainly relies on the leaf rust resistance (Lr) gene or quantitative trait locus (QLr). Although these genetic loci have been insensitively studied during the last two decades, an updated overview of Lr/QLr in a genome-wide level is urgently needed. This review summarized recent progresses in genetic studies of wheat resistance to leaf rust. Wheat germplasms with great potentials in genetic improvement of resistance to leaf rust were highlighted. Key information about the genetic loci carrying Lr/QLr were summarized. A genome-wide chromosome distribution map for all the Lr/QLr was generated based on the released wheat reference genome. In conclusion, this review has provided valuable sources for both wheat breeders and researchers to understand the genetics of resistance to leaf rust in wheat.

Fleets of drones have attracted a lot of attention from the research community in recent years. One of the biggest challenges in deploying such systems is localization. While GNSS localization systems can only be effective in open outdoor environments, new solutions based on radio sensors (e.g., ultra-wideband) are increasingly being used for localization in various situations and environments. However, self-localization without prior knowledge of anchor positions remains an open problem which, for example, makes it impossible to track a moving target. In this article, we provide a comparison of different variants of gradient descent-based algorithms, with a new improved variant, for solving the localization problem using relative distance measurements and multilateration. It is applied to self-localization of anchors and tracking targets using ultra-wideband distance sensors. A realistic simulation of drone tracking and anchors’ localization is performed to demonstrate the robustness and accuracy of the proposed approach.

In order to enhance the gain of antenna suitable for the airplane mounted platform, a conformal tightly coupled antenna array is investigated in this paper. Especially, three-dimensional (3-D) inkjet printing technique is used to implement the conformal property. The printing of antenna substrate and radiation layer is implemented by combining the fused deposition modelling and microdroplet injection molding technologies based on the existing 3-D printer. Here, through a unique combination of 3-D and 2-D inkjet printing of dielectric material and metallic ink, respectively, we demonstrate a monolithically integrated to a nonplanar antenna for the first time. Antenna measurements show that the complete characterization of this new process in terms of minimum feature sizes and achievable conductivities. This antenna configuration offers a high-gain performance with low-cost and rapid fabrication technique by using 3-D printing. The voltage standing wave ratio and radiation patterns are tested after adding the newly designed feed structure. Results shown the design process much efficient. Both antenna element and the array with good properties, which are in very good agreement with the specially mounted platform.

At least 50% of factors predisposing to alcohol dependence (AD) are genetic and women affected with this disorder present with more psychiatric comorbidities, probably indicating different genetic factors involved. We aimed to run a genome-wide association study (GWAS) followed by a bioinformatic functional annotation of associated genomic regions in male and female patients with AD and eight related clinical measures. A genome-wide significant association of rs220677 with AD (p-value = 1.33×10^-8 calculated with the Yates-corrected Chi-square test under the assumption of dominant inheritance) was discovered in female patients. Associations of AD and related clinical measures with seven other single nucleotide polymorphisms listed in previous GWAS of psychiatric and addiction traits were differently replicated in male and female patients. The bioinformatic analysis showed that regulatory elements in the eight associated linkage disequilibrium blocks define the expression of 80 protein-coding genes. Nearly 68% of these and of 120 previously published coding genes associated with alcohol phenotypes directly interact in a single network. This study indicates that a number of genes behind the pathogenesis of AD are different in male and female patients, but implicated molecular mechanisms are functionally connected. The results also suggest the genetic basis of sex-specific psychiatric comorbidities of AD.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

With the proportional reduction of MOSFET size, the leakage-to-barrier reduction (DIBL) effect leads to a more significant increase in the tunneling current on the gate, and the appearance of the gate tunneling current also seriously affects the static characteristics of the device. In this paper, a new theoretical model of the relationship between the direct tunneling current and the thickness of the oxide layer under the DIBL effect is proposed for the MOSFET device with ultra-thin oxide layer. On this basis, the characteristics of the MOSFET device are studied in detail by using HSPICE, and their working conditions are quantitatively analyzed. The characteristic variation trend of small-size devices under the influence of gate tunneling current is predicted. The simulation results using BSIM4 model are consistent with the theoretical model. The theory and data in this paper will provide useful reference for large scale integrated circuit design.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

As solar energy is a low-cost and clean energy source, there has been a great deal of interest in how to harvest it. To absorb solar energy efficiently, we have designed a broadband metamaterial absorber based on the principle of Fabry–Pérot (FP) cavity and surface plasmon resonances (SPRs). We propose a broadband perfect absorber consisting of a four-layer structure of silica-tungsten-silica-titanium (SiO2-W-SiO2-Ti) for the incident light wavelength range of 300–2500 nm. The structure achieves perfect absorption of incident light in the wavelength range of 351.8–2465.0 nm (absorption >90%), with an average absorption of 96.3%. The advantage of our proposed structure is that it combines the characteristics of both high and broadband absorption and has a high overall absorption efficiency for solar radiation. It is also independent of polarization and insensitive to incident angle. We investigated how absorption was affected by different structures, materials, geometrical parameters, and refractive indices for different dielectric materials, and we explored the reasons for high absorption. This structure is refractory and ultra-thin, and it offers a good trade-off between bandwidth and absorption. It therefore has premium application prospects and value.

Ganoderma boninense is the major causal agent for the basal stem rot (BSR) disease in oil palm, causing the progressive rot of the basal part of the stem. Despite its prominence, key pathogenicity determinants for the aggressive nature of hemibiotrophic infection remain unknown. In this study, genome sequencing and annotation of G. boninense T10 were carried out using the Illumina sequencing platform and comparative genome analysis was performed with previously reported G. boninense strains (NJ3 and G3). The pan-secretome of G. boninense was constructed and comprised of 937 core orthogroups, 243 accessory orthogroups, and 84 strain-specific orthogroups. A set of core candidate effector proteins (CEPs) were found to be enriched with catalytic protein classified as the carbohydrate-active enzymes, hydrolases as well as non-catalytic proteins. Differential expression analysis revealed an upregulation of CEP genes which was linked to the suppression of PTI signaling cascade while the downregulation of CEP genes was linked to the inhibition of PTI by preventing host defense elicitation. Genome architecture analysis revealed the one-speed architecture of the G. boninense genome and the lack of preferential association of CEP genes to the transposable elements. The findings obtained from this study would aid in the characterization of pathogenicity determinants and molecular biomarkers of BSR disease.