In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Leakages in the water distribution networks (WDNs) are real problems for utilities and other governmental agencies. Timely leak detection and location identification has been a challenge. In this paper, an integrated approach to geospatial and infrared image processing method was used for robust leak detection. The method combines drops in flow, pressure, and chlorine residuals to determine potential water leakage locations in the WDN using Geographic Information System (GIS) techniques. GIS layers were created from the hourly values of these three parameters for the city of Sharjah provided by Sharjah Electricity, Water and Gas Authority (SEWA). These layers are then analyzed for locations with dropped values of each of the parameters and are overlaid with each other. In the case where there were no overlaying locations between flow and pressure, further water quality analysis was avoided, assuming no potential leak. In the case where there are locations with drops in flow and pressure layers, these overlaying locations are then examined for drops in chlorine values. If overlaying locations are found, then these regions are considered potential leak locations. Once potential leak locations are identified, a specialized remote sensing technique can be used for precise leak location. This study also demonstrated the suitability of using an infrared camera for leak detection in a laboratory-based setup. This paper concludes that the following methodology can help water utility companies in the timely detection of leaks, saving money, time, and effort.

The design of processing routes involving the presence of the liquid phase is mainly associated with the knowledge of its surface and transport properties. Despite this need, due to experimental difficulties related to high temperature measurements of metallic melts, for many alloy systems neither thermodynamic nor thermophysical properties data are available. A good example lacking these datasets represents the Ir-Si system, although over the last fifty years, the structures and properties of its solid phases have been widely investigated. To compensate the missing data, the Gibbs free energy of mixing of the Ir-Si liquid phase was calculated combining the model predicted values for the enthalpy and entropy of mixing using Miedema’s model and Free Volume Theory, respectively. Subsequently, in the framework of statistical mechanics and thermodynamics, the surface properties were calculated using the Quasi Chemical Approximation (QCA) for the regular solution, while to obtain the viscosity, the Moelwyn-Hughes (MH) and Terzieff models were applied. Subsequently, the predicted values of the abovementioned thermophysical properties were used to model the non-reactive infiltration isotherm of Ir-Si (eutectic) / SiC system.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

We present a robust, fresh-frozen approach to immunohistochemistry (IHC), without committing the tissue to IHC via fixation and cryopreservation while maintaining long-term storage, using LiCor-based infrared (IR) quantification for sensitive assessment of TH in immunoreacted mid-brain sections for quantitative comparison across studies. In fresh-frozen tissue stored up to 1 year prior to IHC reaction, we found our method to be highly sensitive to rotenone treatment in 3-month-old Sprague-Dawley rats, and correlated with a significant decline in rotarod laten-cy-to-fall measurement by approximately 2.5 fold. The measured midbrain region revealed a 31% lower TH signal when compared to control (p<0.01 by t test, n=5). Bivariate analysis of in-tegrated TH counts versus rotarod latency-to-fall indicates a positive slope and modest but sig-nificant correlation of R2=0.68 (p<0.05, n=10). These results indicate this rapid, instrument-based quantification method by IR detection successfully quantifies TH levels in rat brain tissue, while taking only 5 days from euthanasia to data output. This approach also allows for the identifica-tion of multiple targets by IHC with the simultaneous performance of downstream molecular analysis within the same animal tissue, allowing for the use of fewer animals per study.

Diabetic patients need long-term and frequent glucose monitoring to assist in insulin intake. The current finger-prick devices are painful and costly which make noninvasive glucose sensors highly demanded. In this review paper, we discuss several advanced electromagnetic (EM) wave based technologies for noninvasive glucose measurement, including infrared (IR) spectroscopy, photoacoustic (PA) spectroscopy, Raman spectroscopy, fluorescence, optical coherent tomography (OCT) and microwave sensing. Development and progress of each method are discussed regarding fundamental principle, system setup and experimental results. Despite the promising achievements reported previously, there is no established product to obtain FDA approval or survive marketing test. Limitations and prospects of these techniques are discussed at the end of this review.

A typical vibrational spectrum in the ice phase has four separate bands: translation, libration, bending and stretching. Ice X, the final ice phase under high pressure, shows an exotic vibrational spectrum. Theoretically, an ideal crystal of ice X only has one peak at 998 cm-1 for Raman scattering and two peaks at 450 cm-1 and 1507 cm-1 for infrared absorption in this work. These three characteristic peaks are indicators of the phase transition between ice VII/VIII and ice X. Despite much experimental and theoretical work on ice X, only this study has clearly indicated these characteristic peaks in the region of the IR band. The phonon density of states shows quite different features than ice VIII, which could be verified by inelastic neutron scattering in the future. The dynamic processes of 15 vibrational normal modes are discussed and the typical hydrogen bonds are missing.

We study impact of geometry on leakage loss in negative curvature fibers made with As₂Se₃ chalcogenide and As₂Se₃ chalcogenide glasses for carbon dioxide (CO₂) laser transmission. The minimum leakage loss decreases when the core diameter increases both for fibers with six and for fibers with eight cladding tubes. The optimum gap corresponding to the minimum loss increases when the core diameter increases for negative curvature fibers with six cladding tubes. For negative curvature fibers with eight cladding tubes, the optimum gap is always less than 20 μm when the core diameter ranges from 300 μm to 500 μm. The influence of material loss on fiber loss is also studied. When material loss exceeds 10² dB/m, it dominates the fiber leakage loss for negative curvature fiber at a wavelength of 10.6 μm.

Seaweeds have been the target of much attention due to the known bioactivities of some of their compounds. Although many studies about the application of seaweeds in various areas are available, these data are mostly about the raw extracts and not about specific compounds, such as seaweeds pigments. Moreover, the fungal infections of the skin, nails and hair caused by dermatophytes, are the most common fungal infections in humans. These pathologies require long periods of topical and/or systemic treatment that are associated with adverse effects and contraindications. This study had two objectives, the first was to evaluate the possibility of isolating and characterizing the pigments of Calliblepharis jubata and Fucus vesiculosus; the second was to assess their antifungal activity. The extraction of pigments was performed using a method of extraction by exhaustion; the purification was carried out by column chromatography. Three techniques were used to characterize the pigments, thin layer chromatography (TLC), UV-visible spectrophotometry and Fourier-transform infrared spectroscopy (FTIR). The antifungal activity was evaluated using the micro-dilution method, following the EUCAST international standards, on three dermatophytes, Trichophyton rubrum, Trichophyton mentagrophytes and Microsporum canis. It was possible to observe that the extract obtained from the seaweed C. jubata and F. vesiculosus, corresponding to the purified pigment phycobiliprotein, and the crude extract, an enriched extract, obtained from the seaweed C. jubata showed antifungal activity against the three fungal agents of human skin infection.

This study aimed to investigate the atherogenicity (quality) of LDL particles in patients with acute and recovered from COVID-19 infection. The participants were adults, aged 18 years or older of both sexes. Those with positive RT-PCR results at baseline were included in the Acute COVID-19 group (n=33), and those with negative RT-PCR six months after acute infection, were included in the Recovered COVID-19 group (n=30). The LDL quality was evaluated using three validated methods: Z-scan, UV-visible spectroscopy, and Lipoprint. The Recovered COVID-19 group showed significantly higher numbers of large LDL particles (less atherogenic) than the Acute COVID-19 group (P&lt;0.05). We also found that COVID-19 infection was associated with the oxidative modification of LDL particles. D-dimer and CRP levels were correlated with Z-scan results and antioxidant-amount estimate. Moreover, we noticed that the infection left a sequel in LDL quality, even after six months of recovery. These findings highlight the importance of monitoring lipids during and after recovery from COVID-19 infection, and their potential deleterious effect on the LDL profile might correlate with the progression of atherosclerosis and poor clinical outcomes.

The emergence of Non-Ionizing Radiation (NIR) has stimulated the growth and advancement of technological civilization. NIR is ubiquitous; it has helped improve all fields and even deepened democratic processes through the transfer of data and electronic transmission of results etc. A breathtaking part of NIR is its recent application in the treatment of adverse health effects through radiofrequency ablation, phototherapy, etc. as summarized in Table 1. The benefits of NIR are enormous, however, technological civilization has not come without a cost; some of the adverse health effects associated with NIR include skin cancers, sleep disorders, photo-aging, etc. as summarized in Table 2. Therefore, with the rapid and sporadic increase in the sources of NIR from Natural and Artificial sources including fossil fuel burning, Starlink technology, mobile phones, mobile base antennas, etc., background radiation is expected to rise beyond the exposure limit leading to health illnesses. Intrinsically, there is a dare need to marry concerns that evolve with this growth. Hence, this review article aims to congregate the health hazards associated with NIR and the state-of-the-art applications of NIR in medicine and the health sector in Nigeria being a developing country. Part of our recommendations is that the government at all levels should set up enforcement agencies and policies to drive strict adherence to NIR as provided by ICNIRP; frequent-periodic assessments of background radiation in public places should be carried out due to the increasing sources. In addition, further research is needed to ascertain the health hazard from emerging sources of NIR like Starlink technology and to substantiate findings of non-thermal effects.

The Ramazzottius varieornatus tardigrade is an extremotolerant terrestrial invertebrate belonging to the phylum of Tardigrada. At a length of 0.1-1.0 mm, tardigrades are small animals with an exceptional tolerance to extreme conditions such as high pressure, chemicals and irradia-tion. These properties have been attributed to the recently-discovered Dsup protein. Dsup is a nucleosome-binding protein that prevents DNA damage against X-ray and oxidative stress without impairing cell life, also in Dsup-transfected animal and plant cells. However, the precise “protective” role of this protein is still under study. We performed experiments on human cells and shows that, as compared to control cells, Dsup+ cells are more resistant to UV-C exposure and H2O2. Real-time PCR identified different expression patterns of endogenous genes involved in apoptosis, cell survival and DNA damage repair in Dsup+ cells in response to H2O2 and UV-C. While H2O2 treatment in Dsup+ cells only marginally involved the activation of pathways responsible for DNA repair reinforcing the idea of a direct protective effect of the protein on DNA, in UV-C exposed cells, Dsup efficiently upregulates DNA damage repair genes. In conclusion, our data may help to delineate the different mechanisms by which the Dsup protein operates in response to different insults.

UV-Visible spectroscopy method has been developed for the analysis of Thiamine in biological and pharmaceutical product, based on a chromogenic derivatizing reaction using PDAB (P- dimethyl amino benzaldehyde) reagent. A Central Composite Design (CCD) design with response surface methodology was executed for optimization of experimental conditions of drug with a smaller number of experimental trials. Three independent factors, the concentration of PDAB, the volume of PDAB reagent, and volume of HCl, were used to construct a mathematical model and study the effects of these independent factors on responses as absorbance. The colored complex exhibits a Red shift with absorption maximum λmax at 425 nm, which was selected as the analytical wavelength. The drug seems to be linear, which was established via the regression analysis from 5-30 μgmL-1, with an R2 value of 0.998.The % RSD for intraday and interday precision was < 2%, with good recovery ranging from 95.02 to 101.43% with biological and pharmaceutical samples. LOD and LOQ of the developed method were found to be 1.51 μg mL-1 and 4.57 μg mL-1.This method can be used in routine analysis of pharmaceutical products containing aromatic primary amines along with an estimation of biological samples like urine, blood, sweat, faeces.

Palm fatty acid distillate (PFAD) is a by-product from the refining of crude palm oil. It comprises mainly of free fatty acids, having around 45% of palmitic and 33% oleic acids as the major components. Ultra-violet (UV) curable urethane acrylate (UA) oligomers could be synthesized from PFAD by the following procedure. A hydroxyl terminated macromer was first prepared by reacting PFAD with a mixture of isophthalic acid, phthalic anhydride, neopentagylcol (NPG) and pentaerythritol. The macromer is then reacted with 2-hydroxylethylacrylate (2HEA) and toluene diisocynate (TDI) to generate a resin containing acrylate side chains for UV curable application. A series of UA resins were prepared by using 15, 25, 45, 55 and 70% of PFAD respectively. The UA resin has Mw in the range of 3200 to 27,000. They could be cured by UV irradiation at intensity of 225mW/cm². Glass transition temperature (T_g) of the cured film was measured by differential scanning calorimeter (DSC), and hardness of the film was determined by pendulum hardness tester according to ASTM4366. The resins were used in wood coating application. All of the cured films showed good adhesion, hardness and chemical resistant for resins using up to 55% PFAD; however the resin at 70% did not cure properly.

This article delves into the enduring relevance of Liberal International Relations (IR) Theory amidst persistent criticisms regarding power dynamics and its applicability in emerging states. Despite its detractors, Liberal IR Theory offers a nuanced understanding of state behavior, blending social contexts with power dynamics. It recognizes the intricacies of economic interdependence and advocates for a balanced approach in advancing democracy and human rights. While nationalism poses challenges to international institutions, their adaptability endures. Leaders, albeit constrained, retain the capacity to foster peace through visionary leadership and global cooperation. By acknowledging its limitations and fostering open dialogue, Liberal IR Theory continues to evolve, poised to contribute to a just and peaceful global order.

Microplastics (MPs) pollution has become a persisting problem over the last decades and a critical issue for environmental protection and human health. In this context any scientific data able to reveal the MPs presence and to improve the characterization and identification in different systems is valuable. The aim of this paper was to assess available techniques for determining MPs in real freshwater samples and subsequently to highlight the occurrence and type of MPs in the study case area (Somesul Mic River). The specific objectives of the study were: i) MPs separation and visual characterization; ii) microscopic analyses and morphological characterization of MPs; iii) Raman and FT-IR spectroscopic identification of MPs. MPs sampling was performed from the fresh water and sediment using planktonic nets and sieves with different mesh sizes (20 to 500µm). After digestion with hydrogen peroxide, the MPs characterization was performed using both classical microscopic techniques as well as scanning electron microscopy (SEM). For the MPs identification, Raman and FT-IR spectrometry techniques were used. Large (1-5 mm) and small (1 µm to 1 mm) MPs were observed in the shape of fibers, fragments, foam, foils and spheres in various colors (red, green, blue, purple, pink, white, black, transparent, opaque). Polymers were identified related to scientific literature and reference spectra. The presence of polyethylene (PE), polypropylene (PP) and polystyrene (PS) was registered for all sampling point. The MPs laboratory investigations have raised some issues regarding the identification of MPs particles with the size smaller than 500µm, being characterized especially under microscope. Small MPs particle dispersed on cellulose filter were identified using micro-Raman spectroscopy highlighting the same type of polymers. The results showed that both spectrometric methods Raman or FT-IR confirm the identification of the same type of polymers. No differences were registered between the sampling points due to the widespread presence of MPs. The sediments samples presented a greater abundance compared to the water samples. Overall, it is necessary to continue the optimization of the MPs separation protocol and identification according to the complexity of samples, mainly due to the limitation and lack of spectral databases.

Currently, synthetic diamonds are finding new applications. Quantum devices can be created based on diamond plates with the desired concentration of defects in the structure of the crystal lattice. NV color centers can be used in quantum applications by irradiating plates with high-energy particles, followed by annealing at temperatures above 800°C to develop the spin-optical properties of the centers Diamond plates are subjected to electron irradiation and much less often to proton irradiation. As a result, synthetic diamond plates with NV centers ob-tained by proton irradiation are less studied, although proton irradiation makes it possible to obtain a layered structure of NV centers. In this work, single crystal diamond plates irradiated with protons were studied using polarization microscopy, IR spectroscopy and ODMR spectros-copy. It is shown that when creating NV centers, the distribution and concentration of C – defects in the sample, as well as mechanical stresses before and after irradiation (with subsequent an-nealing), can differ significantly from each other.

Nowadays, diamonds are widely used in science and technology. However, the properties of diamonds due to their defects are not fully understood. In addition to optical methods, positron annihilation spectroscopy (PAS) can be successfully used to study defects in diamonds. Positrons are capable of detecting vacancies, small and large clusters of vacancies induced by irradiation, by providing information about their size, concentration, and chemical environment. By mapping in the infrared (IR) range, it is possible to consider the admixture composition of the main inclusions of the whole plate. The article presents the results of the study of defects in synthetic diamond plates, one of which was irradiated by electrons. Presents data about the distribution of the defect concentration obtained by Infrared spectroscopy. PAS with a monochromatic positron beam can be used as a non-destructive technique of detecting defects (vacancy) distribution over the depth of diamond plates.

Understanding the structure and properties of MgCl2/TiCl4/ID nanoclusters is a key to uncover the origin of Ziegler-Natta catalysis. In this work MgCl2/TiCl4 nanoplatelets derived by machine learning and DFT calculations have been used to model the interaction with ethyl-benzoate EB (as internal donor) with available exposed sites of binary TixCly/MgCl2 systems. The influence of vicinal Ti2Cl8 and coadsorbed TiCl4 on energetic, structural and spectroscopic behaviour of EB has been considered. The adsorption of homogeneous-like TiCl4EB and TiCl4(EB)2 at the various surface sites have been also simulated. Calculations have been carried out by employing B3LYP-D2 and M06 functionals. The adducts have been characterized by computing IR and Raman spectra that have been found to provide specific fingerprints useful to identify surface species; IR spectra have been successfully compared to available experimental data.

Fire accidents are causing a huge human death as well as economic losses throughout the world every year. But a novel fire detection and extinguishing system could reduce these losses to a great extent. We are proposing a cost effective and yet very efficient system which has been developed in our laboratory and evaluated while in operation. Our system consists of two units: detection unit and extinguishing unit. For detection purposes we used smoke, IR and temperature sensors. While for extinguishing purposes we used both foam and water. We used a PC to process and control our system through LabVIEW software of National Instrument, USA. The detection unit will send signal through a wireless module to PC if fire is detected. Then PC (LabVIEW) will process the signal and using relay module first of all the electric power and gas lines will be turned off. The extinguishing unit will then release foam or water to extinguish the fire. The system will send SMS to the predefined numbers using GSM module. Our system is location independent as it uses GSM and can be operated from remote location using wireless module. After performance evaluation it was found to be fast and reliable.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

Various wood fibres, including pine and flax, are used in wood–plastic composites (WPCs). This paper studies the effect of the lignin content on the morphological and thermal degradation and damage due to the ultraviolet (UV) aging of polypropylene/flax (PP-flax) and polypropylene/pine (PP-pine) fibres composites. Flax and pine fibres exhibited distinct densities of 1.51 and 1.47 g/cm³, respectively, potentially influenced by growth factors and varying compositions of light substances, such as hemicellulose, lignin, and impurities. The thermal decomposition mass loss increased proportionally with the percentage of lignin in the fibre. From 238°C to 390°C, the pine fibre exhibited a 72% mass loss compared to flax fibre, which showed a 54% mass loss, owing to the higher lignin content in pine fibres. Based on differential scanning calorimetry (DSC), the fibre composition affected the material melting temperature. Moreover, DSC curves revealed a higher degree of crystallinity in the case of the PP-flax biocomposite (12%) compared to pure polypropylene (9%) and PP-pine (6%). This result can be attributed to the high content of crystalline components in flax fibres, such as cellulose. Acoustic emissions analysis confirmed that the high lignin content delays degradation and mitigates the appearance of microcracks on the surface of the PP-pine biocomposite. Overall, the study provides valuable data for understanding the UV degradation phenomenon in biocomposites and highlights the influence of fibre composition on material performance.

Euglenoids are a common component of primary producers in high acidic and organic shallow freshwater systems. They are free-living photosynthetic motile flagellates exhibiting rapid responses to various external stimuli including chemical pollution. The unique combination of diverse physiological processes of Euglena such as photosynthesis, movement, and orientation offers a range of sensitive criteria that respond to aquatic pollutants. This has led to the development of several acute and chronic assay methods to monitor the adverse impacts of potent toxicants in aquatic ecosystems. Euglenoids also reflect the consequences of physical stress factors such as UV radiation. This review summarizes the ecotoxicity studies using euglenoid flagellates as model species and their potential to contribute toward rapid screening of ecological impacts of pollution in the aquatic environment. Factors determining the reliability of Euglena tests are outlined.

A prominent feature of stress-tolerant microalgae is their versatile metabolism allowing then to synthesize a broad spectrum of molecules with beneficial effects on many aspects of human body functioning. This is in line with the current understanding that many stress-induced deleterious processes in the human body and in photosynthetic cell are mediated by the same mechanisms such as free-radical attacks and lipid peroxidation. These related risks are kept at bay by optical screening of harmful UV, enzymatic ROS elimination systems, and potent low-molecular antioxidants. Microalgae synthesize a broad spectrum of compounds exerting antioxidant and/or UV-absorbing properties. In microalgae, they increase stress-resilience of these organisms. In human body, they exhibit photoprotective, antiaging, and sunscreen activities. Therefore, these algal metabolites were recognized as promising ingredients for innovative cosmetics and cosmeceutical formulations. Ever increasing effort is being invested into the search for new natural biologically active substances from microalgae. This trend is also fueled by the growing demand for natural raw materials for food, pharmaceuticals and cosmetology associated with the global transition to a "greener" lifestyle. Here, we review the currently accumulated knowledge about the main groups of cosmeceutical compounds from microalgae.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

The expedited development of drugs targeting gene products associated with insulin resistance holds the potential to enhance our comprehension of type 2 diabetes mellitus (T2DM). The virtual screening based on a three-dimensional (3D) protein structure has been expected as potential technique to accelerate a development of molecular target drugs. Among the targets implicated in insulin resistance, genetic characterization and protein function of Grb14 have been clarified without contradiction. The Grb14 gene displays notable variations in T2DM, and its gene product known to inhibit the function of the insulin receptor (IR) by directly binding to the tyrosine kinase domain. In the present study, a virtual screening, based on 3D structure of IR tyrosine kinase domain (IRβ) in complex with part of Grb14, was conducted to find compounds that can disrupt the complex formation between Grb14 and IRβ. First, ten compounds were selected from 154,118 compounds via hierarchical in silico structure-based drug screening, composed of grid docking-based and genetic algorithm-based programs. The experimental validations suggested that the one compound can affect blood glucose level. The molecular dynamics simulations and co-immunoprecipitation analysis showed that the compound did not completely suppress the protein–protein interaction between Grb14 and IR, though competitively bound to IR with the tyrosine kinase pseudosubstrate region in Grb14.

Diffusion-controlled cyclic voltammograms at fast scan rates show peak shifts as well as decreases in the peak currents from the predicted diffusion-controlled currents especially when currents are large in low concentration of supporting electrolyte. This has been conventionally recognized as an IR-drop effect by solution resistance on the peaks as well as heterogeneous kinetics. It is also brought about by negatively capacitive currents associated with charge transfer reactions. The reaction product generates dipoles with counterions to yield a capacitance, of which current flows oppositely to that of the double layer capacitance. The three effects are specified here in the oxidation of a ferrocenyl derivative by fast scan voltammetry. The expression for voltammograms complicated with IR-drop is derived analytically, and yields deformed voltammograms. The peak shift is approximately linear with the IR-term, but exhibits a convex variation. Dependence of some parameters on the peaks by the IR-drop is compared with those by the negative capacitance. The latter is more conspicuous than the former under conventional conditions. The two effects cannot be distinguished specifically except for variations of conductance of the solution.

This paper explores the dynamic interplay of K-12 education, the Fourth Industrial Revolution (IR 4.0), and internationalization in the Philippines. Through qualitative content analysis, key themes emerged, shedding light on the impact of K-12 education on global competitiveness, challenges in embracing IR 4.0 technologies, and opportunities arising from internationalization efforts. The findings underscore the significance of curriculum alignment with international standards, comprehensive digital literacy training, and fostering a global mindset to prepare students for the digitally-driven, interconnected world. Understanding the implications of these themes is crucial for the Philippines' education system, as it navigates towards a transformative and globally competitive future. Further, this research offers evidence-based recommendations and addresses research gaps, contributing to a broader understanding of how the convergence of these forces shapes the future of Philippine education. Future research avenues may explore long-term impacts on workforce preparedness, innovative IR 4.0 integration, and the effectiveness of internationalization efforts on educational outcomes. Eventually, this study inspires an education system that nurtures learners equipped to thrive in an ever-evolving global landscape.

A series of cysteine-based perfluoroaromatic (hexafluorobenzene (I) and decafluorobiphenyl (II) were synthesized and established as a chemoselective and available core to simple or more complex systems since small molecules to biomolecules with interesting properties. As proof of concept of the potential application of perfluorinated derivatives as non-cleavable linkers, some antibody-perfluorinated conjugates were prepared via thiol, demonstrating that the bioconjugation process doesn’t affect to the macromolecular entity. Besides, some molecular properties of synthesized compounds are evaluated using a combination of spectroscopic characterization (FT-IR and 19F-NMR chemical shifts) and theoretical calculations. Moreover, molecular Docking was also developed to predict cysteine-based hexafluorobenzene and decafluorobiphenyl derivatives’ affinity against topoisomerase Il and cyclooxygenase 2 (COX-2). The results suggested that mainly cysteine-based decafluorobiphenyl derivatives could be potential topoisomerase II α and COX-2 inhibitors, becoming potential anticancer agents and candidates for anti-inflammatory treatment.

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

Sol-gel route represents a valuable technique to obtain functional materials, in which organic and inorganic members are closely connected. Herein four hybrid materials, containing caffeic acid entrapped in a silica matrix at 5, 10, 15 and 20 wt%, were synthesized and characterized through FT-IR and UV-Vis spectroscopy. FT-IR analysis was also performed to evaluate the ability to induce the hydroxyapatite nucleation. Despite some structural changes occurred on the phenol molecular skeleton, hybrid materials showed scavenging properties vs DPPH and ABTS+ radicals, which was dependent on the tested dose and on the caffeic acid wt%. Finally, the SiO₂/caffeic acid materials have been proposed as valuable antibacterial agents against Escherichia coli and Enterococcus faecalis.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

Plastic materials have revolutionized modern life, particularly in the domain of food packaging, owing to their versatility, lightweight nature, and ease of processing. However, the environmental ramifications of non-degradable plastics have raised concerns. Polylactic acid (PLA), derived from renewable sources, presents a sustainable alternative due to its biodegradability and exceptional barrier, mechanical, and safety properties. Nevertheless, the high UV transmittance of PLA limits its use for photosensitive food and pharmaceutical packaging, where UV radiation can lead to nutritional loss and spoilage. Various methods have been explored to enhance the UV-blocking capabilities of PLA, including the integration of inorganic nanoparticles and surface coatings. Despite advancements, these approaches often compromise the inherent transparency of PLA. Incorporating large conjugated groups can maintain transparency but introduces additional challenges. This paper reviews modification methods to enhance PLA's UV-barrier properties and anticipates its expanded utility in food and drug packaging, promoting UV resistance and diversifying PLA's applications.

More than twenty-five years ago the Global Solar UV index (UVI) has been introduced as a simple means of visualizing the intensity of ultraviolet radiation and to alert people to the need for sun protection. In our survey among directors of 436 kindergartens in southern Germany we investigated the level of awareness and knowledge about the UVI as well as the practical consequences for sun protection in kindergartens. Less than half of the directors (n=208, 47.7%) had ever heard of the UVI, and only a small minority of them (n=34, 8.7%) used the daily UVI information to adapt sun protective measures in their kindergartens. Detailed knowledge about the UVI was a rarity among the respondents. The proportion of respondents with self-perceived detailed UVI knowledge was five times higher than actual knowledge assessed by an in-depth structured interview using open-ended questions about the UVI (14.2% vs. 2.8%). No clear relationship of UVI awareness, knowledge, and use to directors' age and gender was found. The UVI-related variables also showed no association with directors' knowledge of risk factors for skin cancer and their attitudes towards tanned skin. Overall, the results paint a sobering picture regarding the penetration of the UVI into sun protection policies of German kindergartens. Future public health campaigns should target increasing awareness and understanding of the UVI as well as its importance for sun protection of children.

In this experimental report the biocompatibility of elastomeric scaffold structures made via stereolithography employing table-top 3D printer (Ember, Autodesk) and commercial resin FormLabs Flexible (FormLabs) was studied. The samples were manufactured using standard printing and development protocol, which is known to inherit cytotoxicity due to remaining non-polymerized remaining monomers, despite the polymerized material being fully biocompatible. Additional steps were taken to remedy this problem: the fabricated structures were soaked in isopropanol and methanol for different conditions (temperature, duration) in order to leach out the non-polymerized monomers. Also printed structures were UV exposed to assure maximum polymerization degree of the material. Post-processed structures were seeded with myogenic stem cells and the number of live cells was evaluated as an indicator for the material biocompatibility. The straightforward post-processing protocol enhances the biocompatibility by 7 times after 7 days soaking in isopropanol and methanol and is comparable to control (glass and polystyrene) samples. This proposes the approach as a novel and simple method to be widely applicable for dramatic cytotoxicity reduction of optically 3D printed micro-/nano-scaffolds for biomedical applications.

The gap in knowledge regarding the radiative effects of aerosols in the UV region of the solar spectrum is large, mainly due to the lack of systematic measurements of the aerosol single scattering albedo (SSA) and absorption optical depth (AAOD). In the present study, spectral UV measurements performed in Thessaloniki, Greece by a double monochromator Brewer spectrophotometer in the period 1998 - 2017 are used for the calculation of the aforementioned optical properties. The main uncertainty factors have been described and there is an effort to quantify the overall uncertainties in SSA and AAOD. Analysis of the results suggests that the absorption by aerosols is much stronger in the UV relative to the visible. SSA follows a clear annual pattern ranging from ~0.7 in winter to ~0.85 in summer at wavelengths 320 – 360 nm, while AAOD peaks in summer and winter. The average AAOD for 2009 – 2011 is ~50% above the 2003 – 2006 average, possibly due to increased emissions of absorbing aerosols related to the economical crisis and the metro-railway construction works in the city center. A detailed analysis of the uncertainties in the retrieval of the SSA and the AAOD from the Brewer spectrophotometer has been also performed.

Coffee and caffeine have been used as solar absorbers and also to increase the thermal stability and efficiency of perovskite solar cells. In this work, we report the sensing of extremely alkaline pH by colloidal coffee solution aided by generation of an optical absorption band in the near-UV region. This generation of absorption band could be explained by the orientation induced dipole-dipole interactions arising from differing caffeine-solvent interactions with varying pH. Such a generation leads to the lowering of direct as well as indirect bandgaps from 4 eV-->2.8 eV& 3.4 eV-->2.5 eV, respectively. We also estimate the changes in optical energy storage efficiency, inferring it to be highest for pH 11 having the highest intensity of the generated absorption band (λ_abs≈360 nm). With these observations and further deductions, the work reported in this paper would be of immense interest to the researchers working in the field of development of chemical pH sensors and also in the development of novel UV absorbers.

The aim of the study was the evaluation of the efficiency of selected abiotic elicitors, i.e. silver and cadmium ions, ultrasound, and UV-C irradiation, in the stimulation of triterpenoid biosynthesis, accumulation, and saponin secretion in Calendula officinalis hairy root cultures. Apart from the possible enhancement of triterpenoid production, the relationship between primary and secondary metabolism (represented respectively by sterols and pentacyclic triterpenes), modifications of the sterol compositional profile, and fluctuations in the total triterpenoid content were monitored in the performed experiments. The main phenomenon observed as a response to heavy metal treatment was the stimulation (up to 12-fold) of the secretion of saponins, accompanied by significant changes in sterol composition. Ultrasound stimulated the secretion of saponins (up to 11-fold); however, it exerted diverse influences on the triterpenoid content in hairy root tissue (stimulating or decreasing) depending on the duration of the exposure to the elicitor. UV-C radiation caused a slight increase in the content of both sterols and saponins in hairy root tissue, and stimulated saponin secretion up to 8.5-fold. The expected symptoms of the competition between the biosynthetic pathways of sterols and pentacyclic triterpenoids were less evident in reactions to abiotic stressors than those reported previously for biotic elicitors

In the past few years, micromodels have become a useful tool for visualizing flow phenomena in porous media with pore structures, e.g., the multifluid dynamics in soils or rocks with fractures in natural geomaterials. Micromodels fabricated using glass or silicon substrates incur high material cost; in particular, the microfabrication-facility cost for making a glass or silicon-based micromold is usually high. This may be an obstacle for researchers investigating the two-phase-flow behavior of porous media. A rigid thermoplastic material is a preferable polymer material for microfluidic models because of its high resistance to infiltration and deformation. In this study, cyclic olefin copolymer (COC) was selected as the substrate for the micromodel because of its excellent chemical, optical, and mechanical properties. A delicate micromodel with a complex pore geometry that represents a two-dimensional (2D) cross-section profile of a fractured rock in a natural oil or groundwater reservoir was developed for two-phase-flow experiments. Using an optical visualization system, we visualized the flow behavior in the micromodel during the processes of imbibition and drainage. The results show that the flow resistance in the main channel (fracture) with a large radius was higher than that in the surrounding area with small pore channels when the injection or extraction rates were low. When we increased the flow rates, the extraction efficiency of the water and oil in the mainstream channel (fracture) did not increase monotonically because of the complex two-phase-flow dynamics. These findings provide a new mechanism of residual trapping in porous media.

: The article presents a brief review of cooling systems of various temperature levels (from 0.1 K to 230 K) for radio astronomical receivers of photonics and electronics. The features of various levels of cooling and the requirements for the design of the cooling system are considered in detail, as well as approaches to designing interfaces for cooled receivers: vacuum, cryogenic, electrical, mechanical, optical, and others required for the effective operation of the receiver,. The presented approaches to design are illustrated by a series of joint developments of the authors carried out over the past 45 years, including those produced last year.

Reactions of picolinamides with 1,3-propanesultone in methanol followed by the treatment with ketones led to a series of previously unknown chemical transformations, yielding first pyridinium salts (2a-f) with a protonated endocyclic nitrogen atom and then heterocyclic salts (3a-j) containing a 4-imidazoline ring. The structures of intermediate and final products were determined by IR and 1H, 13C NMR spectroscopy and X-ray study. The effects of the ketone and alcohol structures on the product yield were studied by quantum-chemical calculations. The stability of salts 3a-j towards hydrolysis and alcoholysis makes them excellent candidates for the search of new types of biologically active compounds.

This article presents the results of technical and technological studies of the oil painting by the artist of German origin Werner Tübke “Hiroshima I" (1958). The creative heritage of the author has been little studied and represents scattered data on the technology of painting and artistic techniques. The aim of the work was to determine the artistic materials and painting technolo-gy described in his diaries, using the example of his only painting in Russia – “Hiroshima I". For this purpose, an integrated approach was used using non–invasive control methods - photo in the light of visible luminescence, infrared reflectography (IRR), radiography, portable X-ray fluorescence (XRF), as well as infrared-Fourier spectroscopy (FT-IR) and polarizing microsco-py using microprobes. As a result, the pigment composition of the painting layers was deter-mined, the painting technology was refined, and a previously unknown hidden portrait of Werner Tübke's father was revealed.

A variety of bioactive substances present in fruits and vegetables processed products have health-promoting properties. Consumption of nutrient-rich plant-based products is essential to address undernutrition and micronutrient deficiencies. Preservation is paramount in manufacturing plant-based non-solid foods such as juices, purees, and sauces. Thermal processing has been widely used to preserve fruit and vegetable-based products by reducing enzymatic and microbial activities, thereby ensuring safety and prolonged shelf life. However, the nutritional value of products is compromised due to the deleterious effects of thermal treatments on essential nutrients and bioactive compounds. To prevent the loss of nutrients associated with thermal treatment, alternative technologies are being researched extensively. In studies conducted on non-solid food, UV-C treatment has been proven to preserve quality and minimize nutrient degradation. This review compiles information on the use of UV-C technology in preserving the nutritional attributes of non-solid foods derived from fruit and vegetables. Legislation, market potential, consumer acceptance, and limitations of UV-C are reviewed.

Current methods for the hardening step of functional coatings over different materials imply the use of high temperatures, high energy consumption or long periods of time, which have repercussions on the speed and cost of the product. We report here a simple and low cost methodology for the functionalization of low cost stainless steel, which is modular, depending of the functionality pursued: a levelling layer for smooth the surface of the material, an “easy to clean” property, or both of them. The research is based on sol-gel coatings cured under UV light without requiring high thermal hardening processes making it applicable to plastics and other sensible materials and possessing high chemical and thermal stability. The film ensures lower processing costs, and higher rates of hardening if the adequate medium-pressure lamps are employed. This formulation is also well defined for scaling up the process, so it is possible to perform a continuous coating in large areas by employing mild processing conditions (low temperature, atmospheric pressure). In addition, the sol gel solution was fully characterized and studied in order to guarantee a long service life before deposition, with a focus on industrial applications in the domestic sector.

The leaves of Ligustrum robustum have been applied as Ku-Ding-Cha, a functional tea to clear heat and remove toxins; and served as a folk medicine to deal with diabetes, obesity, and hypertension. Trans-p-hydroxycinnamic acid and its esters, which were isolated from the leaves of L. robustum, might be a new resource to prevent diabetes and its complications because of their strong -glucosidase and fatty acid synthase (FAS) inhibitory activities and antioxidant effect. However, the quantitative analytical method for trans-p-hydroxycinnamic acid and its esters in the leaves of L. robustum hasn’t been reported so far. In addition, it was difficult and troublesome to analyze no less than 34 trans-p-hydroxycinnamic acid esters by usual HPLC. Therefore, a new HPLC-UV method using hydrolyzation with sodium hydroxide for quantitation of trans-p-hydroxycinnamic acid and its esters in the leaves of L. robustum was developed in the present study. The optimal hydrolyzation conditions were as follows: 1 mL sodium hydroxide aqueous solution (1 M) was added into 1 mL the extract of L. robustum and incubated at 80 °C for 2 h , and then 1 mL hydrochloride (1 M) solution was added. HPLC analysis was performed in reverse phase mode using a C-18 column, eluting with methanol-0.1% acetic acid aqueous solution (40:60, v/v) in isocratic mode at a flow rate of 1.0 mL/min, and detecting at 310 nm. The analytical method was simple and rapid, which simplified greatly the analytical process. The method was validated in terms of linearity, limit of detection (LOD), limit of quantification (LOQ), precision, and accuracy. High linearity was demonstrated with correlation coefficient of 1.000 for trans-p-hydroxycinnamic acid. The LOD and LOQ values were 1.55 and 4.69 μg/mL, respectively. The relative standard deviations (RSD) of intra-day and inter-day variabilities for trans-p-hydroxycinnamic acid were less than 2%. The percentage recovery of trans-p-hydroxycinnamic acid was 101.2% ± 0.8%. Finally, the proposed method was applied successfully to the determination and comparison of the contents of trans-p-hydroxycinnamic acid and its esters in various extracts of the leaves of L. robustum. The 60%-70% ethanol extracts of L. robustum showed the highest contents of free trans-p-hydroxycinnamic acid (3.96-3.99 mg/g), and the 50%-80% ethanol extracts of L. robustum displayed the highest contents of trans-p-hydroxycinnamic acid esters (202.6-210.6 mg/g). The method can be applied also to the quality control of the products of L. robustum.

(1) Background: Investigating the characteristics of photosynthetic physiological changes of leaves in Mangifera indica L. cv. 'GuIfei' under enhanced UV-B radiation, natural light exposed trees were regarded as control, and 96 kJ·m-2·d-1enhanced UV-B radiation was artificially simulated in the field; (2) Methods: The changes of fruit maturity and fruit quality, leaf net photosynthetic rate (Pn), photosynthetic pigments contents, photochemical reaction, activities of photosynthetic enzymes and their genes expressions were determined; (3) Results: Compared with CK, the percentage of mature fruits of the treatment was significantly increased, and fruit quality was better. The net photosynthetic rate (Pn), the contents of photosynthetic pigment, Hill reaction activity and photochemical quenching coefficient (qP) of the treatment leaves showed a significantly higher trend than CK. The activities of Rubisco and RCA, and the expression of Rubisco genes rbcL and rbcS were significantly increased; (4) Conclusions: 96 kJ·m-2·d-1 enhanced UV-B radiation treatment improved Rubisco activity through increasing the expression of Rubisco genes rbcL and rbcS, thereby enhancing the CO2-fixing capacity and dark reaction capacity of leaves. Based on this, it raised the net photosynthetic rate of leaves, which promoted the early maturity of 'Guifei' mango by the fast accumulating photosynthetic products.

Red djulis (Chenopodium formosanum) is a native cereal plant in Taiwan; it contains abundant polyphenols, betalian and dietary fiber. The appearance of red djulis is bright red. Therefore, it is also called the “ruby of cereals”. The antioxidative activity of red djulis extract is well-understood. However, the antiaging function still remains unclear. This study examined the potential of red djulis extract for enhancing collagen secretion and preventing cutaneous aging using red djulis extracts. The red djulis extracts are comprised of an abundant active component that can effectively enhance the ability of collagen secretion of dermal fibroblasts, prevent the glycation of collagen and resist the damage of ultraviolet light exposure. After fibroblast treatment with red djulis extracts, TGM1, KRT1, KRT10 and SOD2 genes were up-regulated significantly by 2.3, 4.3, 4.4 and 27.3 times, respectively, compared to those of the control group. Additionally, it can increase COL1A2 gene expression by 43% and decrease MMP9 gene expression 33%. Therefore, it was demonstrated that red djulis extracts affect gene expressions related to the skin barrier, antioxidation and collagen. Moreover, we found positive effects on skin barrier integrity, endogenous antioxidant activity and skin collagen-preservation. The preparation of the red djulis extracts is environmental friendly and can promote the economic value of Chenopodium formosanum; thus, the proposed extract is suitable for applications in the development of food products, especially beverages, skin care and cosmetic products.

One-dimensional shape memory polymer fibers (SMPFs) have obvious advantages in mechanical properties, dispersion properties and weavability. In this work, a method for fabricating semi-crystallization ethylene-vinyl acetate copolymer (EVA) fiber with two-way shape memory effect by melt spinning and ultraviolet (UV) curing was developed. Here, the effect of crosslink density on its performance was systematically analyzed by gel fraction measurement, tensile tests, DSC and TMA analysis. The results showed that the crosslink density and shape memory properties of EVA fiber could be facilely adjusted by controlling UV curing time. The resulting EVA fiber with cylindrical structure had a diameter of 247.13 ± 10.07 μm, and its mechanical strength and elongation at break were 64.46 MPa and 114.33%, respectively. The critical impact of the crosslink density and applied constant stress on the two-way shape memory effect were analyzed. Moreover, the single EVA fiber could lift more than 143 times its own weight and achieve 9% reversible actuation strain. The reversible actuation capability was significantly enhanced by a simple winding design of the single EVA fiber, which provided great potential applications in smart textiles, flexible actuators and artificial muscles.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

UV SO₂ cameras have become a common tool to measure and monitor SO₂-emission-rates, mostly from volcanoes but also from anthropogenic sources (e.g. power plants or ships). In the past years, the analysis of UV SO₂ camera data has seen many improvements. As a result, for many of the required analysis steps, several alternatives exist today. This inspired the development of Pyplis, an open-source software toolbox written in Python 2.7, which aims to unify the most prevalent methods from literature within a single, cross-platform analysis framework. Pyplis comprises a vast collection of algorithms relevant for the analysis of UV SO₂ camera data. These include several routines to retrieve plume background radiances as well as routines for cell and DOAS based camera calibration. The latter includes two independent methods to identify the DOAS field-of-view within the camera images. Plume velocities can be retrieved using an optical flow algorithm as well as signal cross-correlation. Furthermore, Pyplis includes a routine to perform a first order correction of the signal dilution effect. All required geometrical calculations are performed within a 3D model environment allowing for distance retrievals to plume and local terrain features on a pixel basis. SO₂-emission-rates can be retrieved simultaneously for an arbitrary number of plume intersections. Pyplis has been extensively and successfully tested using data from several field campaigns. Here, the main features are introduced using a dataset obtained at Mt. Etna, Italy on 16 September 2015.

Traditional soil characterization methods are time consuming, laborious and invasive and do not allow long-term repeatability of measurements. The overall aim of this paper was to assess and model spatial variability of the soil in an olive grove in south Italy by using data from two sensors of different type: a multi-spectral on-board drone radiometer and a hyperspectral visible-near infrared-shortwave infrared (VIS-NIR-SWIR) reflectance radiometer as well as sample data, to arrive at a delineation of homogeneous areas. The hyperspectral data were processed using continuum removal methodology to obtain information about the content and composition of clay. Differently, the multispectral data were firstly upscaled to the support of soil data using geostatistics and taking into account change of support. Secondly, the two-sensor data were integrated with soil granulometric properties by using the multivariate geostatistical techniques of multi-collocated cokriging and factor cokriging, in order to achieve a more exhaustive and finer-scale soil characterisation. The paper shows the impact of change of support on the uncertainty of soil prediction that can have a significant effect on decision making in Precision Agriculture. Moreover, four regionalised factors at two different scales (two per each scale) were retained and mapped. Each factor provided a different delineation of the field with areas characterised by different granulometry and clay composition. The applied method is sufficiently flexible and could be applied to any number and type of sensors.

The fixation and activation of the dinitrogen molecule, N2 by hexametallic clusters of the general formula {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 (L = CH2-, NH2-, PH2-, OH-, SH-, BH2- and NH2-, M = Ru(II) or Os(II)) were scrutinized by means of density functional theory calculations. In these systems, the dinitrogen molecule, acts as a ligand that bridges the two opposite facing triangular metallic rings, cyclo-M3 of the {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 clusters The hexametallic clusters, that mimick the six Fe cluster of nitrogenase, were found to strongly activate N2, converting it into a hydrazido-like group, N24-. This is substantiated by the calculated N-N bond lengths, Re(N-N) and the stretching frequencies of the N-N bond of dinitrogen, vs(N-N) found in the ranges 1.299 – 1.487 Å and 780 – 1270 cm-1 respectively. Based on the Re(N-N) and vs(N-N) values, the dinitrogen activation depends upon the nature of the hexametallic cluster. Accordingly, the Os(II) clusters were found to activate more strongly the dinitrogen molecule as compared to their Ru(II) counterparts. The nature of the ligand L also affects the extent of the N2 activation by the hexametallic clusters, which follows the order BH2- &lt; NH2- &lt; OH- &lt; CH2- &lt; NH2- &lt; PH2-, SH- for M = Ru(II) and the order BH2- &lt; NH2- &lt; OH- &lt; NH2- &lt; CH2- &lt; PH2- &lt; SH- for M = Os(II). Thus, the strongest N2 activation is observed for the {[(μ2-SH)Os)]6(μ-η1:η3-Ν2)}+6 cluster and the weakest for the {[(μ2-BH)Ru)]6(μ-η1:η3-Ν2)}0 cluster. The calculated Nitrogen-15 NMR isotropic chemical shielding tensors, σiso(15N) exhibit shielding (upfield) upon N2 fixation to the metal centers of the hexametallic clusters, as a results of electron density transfer towards its constituent N nuclei. A multitude of electronic charge distribution partitioning schemes were applied to assist in delineating the bonding properties of the {[(μ2-L)M)]6(μ-η1:η3-Ν2)}0/+6 clusters. Accordingly, it is found that there is a donation/backdonation interaction between the bridging N2 ligand and the two opposing cyclo-M3 rings located on either side. The dinitrogen ligand forms six bonds of mixed covalent/electrostatic nature with the six metal centers of the {[(μ2-L)M)]6)}0/+6 clusters.

In this work, electrochemical deposition (galvanostatic and potentiostatic) techniques were used to obtain of new composite polymer: 3-methylpyrrole - sodium dodecyl sulfate/poly 2-methythiophene (P3MPY-SDS/P2MT) coatings on cobalt -based alloy sample for anticorrosion protection. The sodium dodecyl sulfate as a dopant ion used in electropolymerization practice can have a relevant effect at the anticorrosion protection of the composite polymer layer by blocking the entry of aggressive ions. The cobalt -based alloy substrate had an important influence on the electrochemical performance of the composite coating and this together with the presence of the polymeric layer was achieved by simultaneously formation of a complex oxides film and polymeric layers. The polymeric coatings were analyzed by cyclic voltammetry, Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM) methods. The corrosion protection of P3MPY-SDS/P2MT coated cobalt based alloy has been explored by potentiostatic and potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) procedures in1 M HCl medium. The corrosion establishment of P3MPY-SDS/P2MT covered cobalt based alloy was observed to be ~10 times less than that uncoated specimen and the effectiveness of these composite layers of this coating is above than 90%. The superior efficacy is achieved by the electrochemical polymerization of P3MPY-SDS/P2MT obtained at 0.5 mA/cm2 and 1mA/cm2 current densities and at 0.9V and 1.0V potential applied and in molar ratio 5:1. Corrosion tests result indicated that P3MPY-SDS/P2MT coatings provide good corrosion protection of cobalt -based alloy in aggressive environments.

The work is devoted to the search for effective solutions to the applied problem of early diagnostics of plant stress in the conditions of smart farming and based on modern explicable artificial intelligence (XAI). The study mostly oriented on the theory and practice of XAI, focused on the use of hyperspectral imagery (HSI) and Thermal Infra-Red (TIR) sensor data at the input of a neural network. The first our goal is to build an XAI neural network, explainable due to its structure, the input of which is a datascientist oriented HSI 'explanator', and the output is a biologist oriented TIR 'explanator'. In the middle is SLP-regressor which solves the universal problem of training HSI pixels to temperatures of plants, needed for early plant stress diagnostic. The result can be considered as prototype of a special XAI explanator which is assigned to transform explanator specialized on area 1 onto explanator specialized on area 2. Using this HSI-TIR explanator we ensured the follows: extend HSI data by TIR attribute; providing TIR data for early diagnostic of plant stress; reducing dimensionality HSI needed for TIR training 25 times (from 204 to 8) preserving the same accuracy of temperature prediction (RMSE=0.2-0.3C). This reducing was achieved without using PCA methods. The constructed model is computationally efficient in training: the average training time is significantly less then 1 min (Intel Core i3-8130U, 2.2 GHz, 4 cores, 4 GB). One of the 8 channels, 820 nm, is the leader in correlation with TIR, what allows building local linear temperature prediction functions.

The development of photocurable compositions is in high demand for the manufacture of func-tional materials for electronics, optics, medicine, energy, etc. The properties of the final pho-to-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was es-tablished that a fluorinated cardo copolymide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200°C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

The use of covers to protect blueberry orchards from adverse weather events has increased due to the variability in climate patterns, but the effects of rain cover and netting materials on yield and fruit quality have not been studied yet. This research evaluated the simultaneous effect of LDPE plastic cover, woven cover and netting materials on environmental components (UV light, PAR, NIR and growing degree days, GDD), plant performance (light interception, leaf area index, LAI, yield and flower development), and fruit quality traits (firmness, total soluble solids and acidity) in two blueberry cultivars. On average, UV transmission under netting was 11% and 43% higher compared to that under woven and LDPE plastic covers, while NIR was 8 -13% higher with both types of rain covers, with an increase in fruit air temperature and GDD. Yield was 27% higher under woven cover with respect to netting, but fruit firmness values under netting were 12% higher than those of LDPE plastic cover. Light interception, LAI and flower development explained 64% (p=0.0052) of the yield variation due to the cover material effect. The obtained results suggest that the type of cover differentially affects yield and fruit quality in blueberries due to the specific light and temperature conditions generated under these materials.

The natural compounds of boron have many applications, including as dietary supplement. Communication is based on the discovery that diester chlorogenoborate complex can be detected and quantified from green coffee bean. The study reports that such diester molecule can also be synthesized in stable form by direct reaction of boric acid and chlorogenic acid, in a mixture of acetonitrile–water (1:1, v/v), left to evaporate over a period of 48 hours, at room temperature, resulting a spirocyclic form (diester complex). The diester complex, with its molecular structure and digestibility attributes has potential application as prebiotic in gut health, oral health and as micronutrient essential for microbiota to human and animals.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

Given the high prevalence of cutaneous genus beta human papillomavirus (β-HPV) infections, it is important to understand how they are manipulating their host cells. This is particularly true for cellular responses to UV damage, since our skin is continually exposed to UV. The E6 protein from β-HPV (β-HPV E6) decreases the abundance of two essential UV-repair kinases (ATM and ATR). Since β-HPV E6 reduces their availability, the impact on downstream signaling events has been uncertain. We demonstrate that β-HPV E6 decreases ATM and ATR activation. This inhibition extended to XPA, an ATR target necessary for UV repair, lowering both its phosphorylation and accumulation. β-HPV E6 hinders POLη phosphorylation and foci formation, critical steps in translesion synthesis. ATM’s phosphorylation of BRCA1 is also attenuated by β-HPV E6. However, β-HPV E6’s hindrance of ATM/ATR signaling during UV-associated cell cycle arrest was incomplete. While there was less phosphorylation of immediate downstream targets (CHK1), events further down the cascade were not decreased. These observations are consistent with β-HPV infections making UV radiation more deleterious and support the proposed role of β-HPV in early stages of non-melanoma skin cancer development.

N-acyl hydrazone (NAH) has been remarked as a promising scaffold in drug design, given its versatility, ease of synthesis, and appealing biological activities (i.e., antimicrobial, antitumoral, analgesic, and anti-inflammatory properties). In the global context of increasing resistance of pathogenic bacteria to antibiotics, NAHs represent potential solutions for developing improved treatment alternatives. Thus, this study presents 6 new derivatives of (EZ)-N'-benzylidene-(2RS)-2-(6-chloro-9H-carbazol-2-yl)propanohydrazide that were obtained through a microwave-assisted synthesis method. In more detail, we have joined two pharmacophore fragments in a single molecule, represented by an NSAID-type carprofen structure and a hydrazone-type structure, obtaining a new series of NSAID-N-acyl hydrazone derivatives that were further characterized spectrally using FT-IR, NMR, and HRMS investigations. Moreover, the compounds have been evaluated for their tuberculostatic activity, testing their effects on four M. tuberculosis strains (two of them susceptible to rifampicin (RIF) and isoniazid (INH), one susceptible to RIF and resistant to INH and one resistant to both RIF and INH). The results of our research highlight the potential of the prepared compounds in fighting against antibiotic-resistant M. tuberculosis strains.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Modification the biodegradable matrix was carried by graft-copolymerization polylactide with methacrylic acid of various concentrations. Ultraviolet irradiation with different exposure times to the samples was chosen as the initiator of copolymerization. In the experiment the effect of ultraviolet light on polylactide and graft copolymerization was investigated: the resulting samples were studied by viscosimetry, gravimetry, FTIR, static cation- exchange capacity analysis . The conditions for obtaining grafted copolymers and the dependence of the characteristics on the reaction conditions are established.

Background: SARS-CoV-2 continues to impact human health globally, with airborne transmission being a significant mode for transmission. In addition to tools like vaccination and testing, counter-measures that reduce viral spread in indoor settings are critical. This study aims to assess the efficacy of UV-C light, utilizing the Violett sterilization device, as a countermeasure against airborne transmission of SARS-CoV-2 in the highly susceptible Golden Syrian hamster model. Methods: Two cohorts of naïve hamsters were subjected to airborne transmission from experimentally infected hamsters; one cohort was exposed to air treated with UV-C sterilization, while the other cohort was exposed to un-treated air. Results: Treatment of air with UV-C light prevented the airborne transmission of SARS-CoV-2 from experimentally exposed hamster to naïve hamsters. Notably, this protection was sustained over a muti-day exposure period during peak viral shedding from hamsters. Conclusion: These findings demonstrate the efficacy of the UV-C light to mitigate airborne SARS-CoV-2 transmission. As variants continue to emerge, UV-C light holds promise as a tool to reduce infections in diverse indoor settings, ranging from healthcare facilities to households. This study reinforces the urgency of implementing innovative methods to reduce airborne disease transmission and safeguard public health against emerging biological threats.

The uneven immunogenicity of the attenuated tetravalent dengue vaccine has created the diffi-culty to achieve a balanced protection against all four serotypes of dengue virus (DENV). To overcome this problem, non-replicative-based vaccines have come into focus as their immuno-genicity is adjustable. This approach is excellent for multivalent vaccines but commonly faces the issue of low immunogenicity. In this present study, we developed a non-replicating dengue vaccine composing of UV-inactivated dengue-2 virus (UV-DENV2) and DENV-2 NS1-279 protein encapsidated within nanoparticles. This vaccine candidate was administered in the presence of BCG cell wall cytoskeleton (BCG-CWS) as an adjuvant. We revealed, here, that encapsidated immunogens with BCG-CWS exerted potent activities on both B and T cells and elicited Th-1/Th-2 responses in mice. This was evidenced by strong neutralizing antibody activity with an unde-tectable antibody enhancing activity in a group of mice receiving encapsidated immunogens with BCG-CWS. Importantly, BCG-CWS significantly augmented antibody-mediated comple-ment-fixing activity, strongly stimulated the antigen-specific polyfunctional T cell responses as well as activated mixed Th-1/Th-2 responses specific to DENV2- and NS1-279 antigens. In conclu-sion, BCG-CWS potently adjuvanted the inactivated DENV-2 and subunit DENV immunogens. The mechanism of adjuvanticity remains unclear. This study revealed the potential use of BCG-CWS in vaccine development.

The aim of this study was characterization of some dairy drinks based on Milk Serum regarding major whey proteins (WP) and free amino acids (FAAs) using reversed phase high performance liquid chromatographic (RP-HPLC) methods. The studied WP, -lactalbumin (-La), bovine serum albumin (BSA), -lactoglobulin A (-Lg A) and -lactoglobulin B (-Lg B) were separated on Aeris XB-C18 column at 214 nm detection. The RP-HPLC method was validated by selectivity, linearity (R2 ≥0.99), sensitivity (LOQ, 1.35–10.08 µg mL−1), accuracy (recovery 96.79-103.07%) and precision (% RSD ≤ 4.13%). The total studied WP in studied dairy drinks varied between 1.42 and 3.047 g·L-1. The chromatographic profile of FAAs (aspartic acid, glutamic acid, serine, histidine, arginine, glycine, threonine, alanine, tyrosine, cysteine, tryptophan, methionine, valine, phenylalanine, isoleucine, leucine and lysine) was determined in lyophilized concentrate of Milk Serum by RP-HPLC using pre-column derivatization reaction with orthophthalaldehyde (OPA). The total studied FAAs in studied samples varied between 1.103 and 1.119 mg·g-1. Moreover, the Milk Serum showed bacteriostatic activity against two bacterial strains Escherichia coli and Staphylococcus aureus. The obtained results confirm that dairy drinks based on the Milk Serum constitutes a valuable sources of bioactive components with benefits for human healthy nutrition.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

Nonlinear properties of zinc germanium diphosphide (ZGP) crystals enable their ap-plications in powerful mid-IR optical parametric oscillators and second-harmonic generators. This paper summarizes mechanisms of the laser induced damage (LID) in high-purity ZGP crystals under periodically pulsed nanosecond irradiation by a Ho3+:YAG laser at 2.1 μm. The ZGP samples were manufactured by “LOC” Ent., Tomsk, Russia, or Harbin Institute of Technology, China. The impact of processing techniques and the post-growing methods for polishing and anti-reflection coating on the LID threshold are discussed. The importance of the defect structure of the crystal lattice and the parameters of transparent coatings for increasing the LID threshold is discussed. The impact of the test laser parameters on the LID threshold is analyzed. The transient area near the LID threshold obtained using digital holography is ana-lyzed. Influence of the pre-damage processes on the optical parametric oscillations is reported. Prospects for improving ZGP crystals to further increase the LID threshold are discussed.

Four leather substrates from different animals were treated by dispersions containing hydrophilic composite silica-hyperbranched poly(ethylene imine) xerogels. Antimicrobial activity was introduced by incorporating silver nanoparticles and /or benzalkonium chloride. The gel precursor solutions were also infused before gelation to titanium oxide powders typically employed for induction of self-cleaning properties. The dispersions from these biomimetically premade xerogels integrate environmentally friendly materials with short coating times. Scanning electron microscopy (SEM) provided information on the powder distribution onto the leathers. Substrate and coating composition were estimated by infrared spectroscopy (IR) and ener-gy-dispersive X-ray spectroscopy (EDS). Surface hydrophilicity and water permeability were assessed by water-contact angle experiments. The diffusion of the leather's initial components and xerogel additives into the water were measured by Ultraviolet-Visible (UV-Vis) spectroscopy. Protection against GRAM- bacteria was tested for Escherichia coli, Pseudomonas aeruginosa, and Klebsiella Pneumoniae against GRAM+ bacteria for Staphylococcus aureus, and Enterococcus faecalis and against fungi for Candida albicans. Antibiofilm capacity experiments were performed against Staphylococcus aureus, Klebsiella Pneumoniae, Enterococcus faecalis, and Candida albicans. The application of xerogel dispersions proved an adequate and economically feasible alternative to the direct gel formation into the substrate’s pores for the preparation of leathers intended for medical uses

A hydrothermal technique with microwave heating (200 °C, 2 hours, 2 magnetrons, 2.45 GHz) was modified to obtain UV-C luminescent LaPO4: Pr3+ colloidal nanorods for the potential use in X-ray cancer theranostics. For further possible biofunctionalization, a compound of tartaric acid formed under basic conditions was used as a coating and stabilizing agent to provide colloidal properties to the surface of nanoparticles in basic to neutral aqueous media, which was confirmed by zeta potential measurements. In addition, the colloidal properties and clustering processes of synthesized LaPO4:Pr3+ nanorods in aqueous solutions with different pH values were studied in real time using a highly sensitive laser ultramicroscope operating according to the “light-sheet” scheme. A comparative analysis of the transmission electron microscopy, X-ray powder diffraction and high-energy spectroscopy showed the different effects of synthesis parameters on the morphological, crystalline and luminescent properties of the obtained nanorods. Through optimization of the synthesis parameters, stable aqueous solutions of m-LaPO4:Pr3+ nanorods with sizes less than 30 nm and an intensity of UV-C luminescence equal to 5-10% of the unmodified nanofibers were obtained.

This publication describes the influence of residue monomers in synthesized pressure-sensitive adhesives based on acrylics on main performance such as tack, peel adhesion, shear strength and shrinkage in form of transfer tapes used for joining wooden elements in furniture industry. The discussed carrier-free adhesive tapes are synthesized by photo-crosslinking and photopolymerization with UV radiation of photoreactive prepolymers sandwiched between two adhesive siliconized polyester films. The simultaneous crosslinking and polymerization process under UV lamps carried out under UV lamps placed simultaneously above and below the crosslinked photoreactive polymer layer leads to the production of a carrier-free adhesive film. In this test series it were investigated to what how the intensity of UV radiation and the time of its exposure affect the viscosity of photoreactive compositions, and then the content of unreacted monomers in them and, subsequently, the method of their crosslinking and polymerization, and the concentration of the photoreactive crosslinking compound leading to the obtaining of transfer adhesive tapes, and thus on their tray, peel adhesion, shear strength and shrinkage on the surface of the wood.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Tracking and early identification of suspected cases are essential to control and prevent potential COVID-19 outbreaks. One of the most popular techniques used to track this disease is the use of Infrared cameras to identify individuals with elevated body temperatures. However, they are limited by their inability to be implemented in open public settings such as public parks or even outdoor recreational centers. This limits their ability to effectively track possible COVID-19 patients as open public recreational places such as parks, concert venues and other public venues are hotspots for the spreading of the virus. Other technological solutions such as thermal scanners require an individual to perform the actual testing as they are not individual standalone technologies. This method of testing can potentially cause the transmission of the virus between the tester and the individual getting tested. As can be seen, an alternative solution is essential to solving this issue. In this study, we aim to present the system, design and potential scope of a non-invasive system that can diagnose and identify potential COVID-19 patients using thermal and optical images of the individual using drone technology. The proposed system (COVIDRONE) combines multi-modal machine intelligence, computer vision and real-time monitoring to enable scalable monitoring. The system will also involve the use of machine learning algorithms for better and more accurate diagnosis. We envisage that development of such technologies may help in developing technological solutions to combat infectious disease threats in the future pandemics.

The acylation of unsymmetrical N-benzylbispidinols in aromatic solvents without external base led to formation of supramolecular gels, which possess different thickness and stability depending on the substituents in para-positions of benzylic group and nature of acylating agent as well as on the nature of the solvent used. Structural features of the native gels as well as of their dried forms were studied by complementary techniques including FT IR- and ATR-spectroscopy, AFM, TEM, SEM, SAXS. Structures of the key crystalline compounds were established by X-ray diffraction. Analysis of obtained data allowed speculating on the crucial structural and condition factors that governed the gel formation. The most important factors were: (i) absence of base, either external or internal; (ii) presence of HCl; (iii) presence of carbonyl and hydroxyl groups to allow hydrogen bonding; (iv) presence of two (hetero)aromatic rings at both sides of the molecule. The hydrogen bonding involving amide carbonyl, hydroxyl at 9th position and, very probably, ammonium N-H+ and Cl- anion appear to be responsible for the formation of infinite molecular chains required for the first step of gel formation. Subsequent lateral cooperation of molecular chains into fibers occured, presumably, due to the aromatic pi-pi-stacking interactions. sc-CO2 drying of the gels gave rise to aerogels morphology different from that of air dried samples.

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

The synergic features and enhancing strategies for various photopolymerization systems are reviewed by kinetic schemes and the associated measurements. The important topics include: (i) photo crosslinking of corneas for the treatmnet of corneal deseases using UVA-light (365 nm) light and riboflavin as the photosensitizer; (ii) synergic effects by a dual-function enhancer in a 3-initiator system; (iii) synergic effects by a 3-initiator C/B/A system, having an electron-transfer and oxygen-mediated energy-transfer pathways; (iv) copper-complex (G1) photoredox catalyst in G1/Iod/NVK systems for free radiical (FRP) and cationic photopolymeriation (CP); (v) radical-mediated thiol-ene (TE) photopolymerizations; (vi) superbase photogenerator based-catalyzed thiol−acrylate Michael (TM) addition reaction; and the combined system of TE and TM usinghual wavelength; (vii) dual-wavelength (UV and blue) controlled photopolymerization confinement (PC); (viii) dual-wavelength (UV and red) selectively controlled 3D printing; and (ix) 3-wavelength selectively controlled in 3D printing and additive manufacturing (AM). With minimum mathematics, we present ( for the first time), the synergic features and enhancing strategies for various systems of multi-commponents, initiators, monomers, and under one- two- and there-wavelength light. Therefore, this Review provides not only the bridging between modeling and measurements, but also guidances for further experimantal stuides and new applications in 3D printings and additive manufacturing (AM), based on the innovative concepts (kinetics/schemes).

In modern security situations, tracking multiple human objects in real-time within challenging urban environments is a critical capability for enhancing situational awareness, minimizing response time, and increasing overall operational effectiveness. Tracking multiple entities enables informed decision-making, risk mitigation, and the safeguarding of civil-military operations to ensure safety and mission success. This paper presents a multi-modal electro-optical/infrared (EO/IR) and radio frequency (RF) fused sensing (MEIRFS) platform for real-time human object detection, recognition, classification, and tracking in challenging environments. By utilizing different sensors in a complementary manner, the robustness of the sensing system is enhanced, enabling reliable detection and recognition results across various situations. Specifically designed Radar tag and thermal tag can be used to discriminate friendly and non-friendly objects. The system incorporates deep learning-based image fusion and human object recognition and tracking (HORT) algorithms to ensure accurate situation assessment. After integrating into an all-terrain robot, multiple ground tests were conducted to verify the consistent HORT in various environments. The MEIRFS sensor system has been designed to meet the Size, Weight, Power, and Cost (SWaP-C) requirements for installation on autonomous ground and aerial vehicles.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

The contribution aims to bring forth a novel synthesis route in developing transparent UV-LED curable coatings accounting various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical photo-initiator Omnirad 2100, and two distinct silane based crosslinking agents were blended under a weight ratio of 75:20:5 (without crosslinker) and 70:15:5:10, respectively. The coatings were cured under a UV-LED 4 x 3 matrix light emitting source, in a chamber under controlled atmosphere, by means of an in-house developed conveyor belt type platform, at different conveyor belt speed (5, 50, 150, 250, and 500 mm/s). The morphologies of fabricated coatings were characterized by FTIR revealing high conversion rates (e.g., from 98 to 100%) for increased exposure time as resulted from the 5 or 50 mm/s values, on all combinations. Dynamic-mechanical and optical properties of UV-LED cured transparent coatings were also investigated. A negative shift of a glass transition temperature values with a decrease in exposure time, in all combinations, from about 60 °C to 30 °C, along with storage moduli lowering in the glassy plateau further favor on higher exposure times for curing. The refractive indices of polymers were from 1.38 to 1.40, whereas the thermo-optic coefficients are showing minor changes around value of 2.55∙10-4 K-1.

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

Base excision repair (BER) is a cellular process that removes damaged bases arising from exogenous and endogenous sources including reactive oxygen species, alkylation agents, and ionizing radiation. BER is mediated by the actions of multiple proteins that work in a highly concerted manner to resolve DNA damage efficiently to prevent toxic repair intermediates. During the initiation of BER, the damaged base is removed by one of 11 mammalian DNA glycosylases resulting in abasic sites. Many DNA glycosylases are product inhibited by binding to the abasic site more avidly than the damaged base. Traditionally apurinic/apyrimidinic endonuclease, APE1, was believed to help turnover the glycosylases to undergo multiple rounds of damaged base removal. However, in a series of papers from our laboratory we have demonstrated that UV-damaged DNA binding protein (UV-DDB) stimulates the glycosylase activities of human 8-oxoguanine glycosylase (OGG1), MUTY DNA glycosylase (MUTYH), alkyladenine glycosylase/N-methylpurine DNA glycosylase (AAG/MPG), and single-strand selective monofunctional glycosylase (SMUG1), between three-to-five-fold. Moreover, we have shown UV-DDB can assist chromatin decompaction facilitating access of OGG1 to 8-oxoguanine damage in telomeres. This review summarizes the biochemistry, single-molecule, and cell biology approaches that our group used to directly demonstrate the essential role of UV-DDB in BER.

Access to nasopharyngeal swabs for sampling remain a bottleneck in some regions for COVID-19 testing. This study develops a distributed manufacturing solution using only an open source manufacturing tool chain consisting of two types of open source 3-D printing and batch UV curing, and provides a parametric fully free design of a nasopharyngeal swab. The swab was designed using parametric OpenSCAD in two components (a head with engineered break point and various handles), which has several advantages: i) minimizing print time on relatively slow SLA printers, ii) enabling the use of smaller print volume open source SLA printers, iii) reducing the amount of relatively expensive UV resin, and iv) enabling production of handle on more accessible material extrusion 3-D printers. A modular open source UV LED box was designed, fabricated for $45 and tested for batch curing. Swabs can be fabricated for $0.06-$0.12/swab. The results of the mechanical validation tests showed that the swabs could withstand greater forces than would be expected in normal clinical use. The swabs were also able to absorb a significant amounts of synthetic mucus materials and passed abrasion and handling tests. The results show the open source swab are promising candidates for clinical trials.

The radar sensor described realizes healthcare monitoring capable of detecting subject chest-wall movement caused by cardiopulmonary activities, and wirelessly estimating the respiration and heartbeat rates of the subject without attaching any devices to the body. Conventional single-tone Doppler radar can only capture Doppler signatures because of a lack of bandwidth information with noncontact sensors. In contrast, we take full advantage of impulse radio ultra-wideband (IR-UWB) radar to achieve low power consumption and convenient portability, with a flexible detection range and desirable accuracy. A noise reduction method based on improved ensemble empirical mode decomposition (EEMD) and a vital sign separation method based on the continuous-wavelet transform (CWT) are proposed jointly to improve the signal-to-noise ratio (SNR) in order to acquire accurate respiration and heartbeat rates. Experimental results illustrate that respiration and heartbeat signals can be extracted accurately under different conditions. This noncontact healthcare sensor system proves the commercial feasibility and considerable accessibility of using compact IR-UWB radar for emerging biomedical applications.

Powerful emitters of the ultraviolet C (UVC) light in the wavelength range of 230-280nm are necessary for the development of effective and safe optical disinfection technologies, high-sensitive optical spectroscopy and non-line-of-sight optical communication. This review considers such UVC-emitters with electron-beam pumping of heterostructures with quantum wells in the (Al,Ga)N material system. The important advantages of these emitters include the absence of the critical problem of p-type doping and the possibility of achieving record (up to several tens of watts for peak values) output optical power values in the UVC range. The review consistently considers about a decade of world experience in the implementation of various UV emitters with various types of thermionic, field-emission, and plasma-cathode electron guns (sources) used to excite various designs of active (light-emitting) regions in heterostructures with quantum wells AlxGa1-xN/AlyGa1-yN (x = 0 − 0.5, y = 0.6 − 1) fabricated either by metal-organic chemical vapor deposition or by plasma-activated molecular beam epitaxy. Special attention is paid to the production of heterostructures with multiple quantum wells/two-dimensional(2D) quantum disks GaN/AlN with a monolayer (1ML ~ 0.25nm) thickness, which ensures a high internal quantum efficiency of radiative recombination in the UVC range, low elastic stresses in heterostructures, and a high output UVC-optical powers.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

In this perspective, we identify emerging frontiers in clinical and basic research of melanocyte biology and its associated biomedical disciplines. We describe challenges and opportunities in clinical and basic research of normal and diseased melanocytes that impact current approaches to research in melanoma and the dermatological sciences. We focus on four themes: (1) clinical melanoma research, (2) basic melanoma research, (3) clinical dermatology, and (4) basic pigment cell research, with the goal of outlining current highlights, challenges, and frontiers associated with pigmentation and melanocyte biology.

Sodium-phosphate-based glass-ceramics (GCs) are promising materials for a wide range of applications, including solid-state sodium-ion batteries, microelectronic packaging substrates, and humidity sensors. This study investigates the impact of 24-hour heat-treatments at varying temperatures on Na-Ge-P glass, with a focus on (micro)structural, electrical, and dielectric properties of prepared GCs. Various techniques such as powder X-ray diffraction (PXRD), infrared spectroscopy-attenuated total reflection (IR-ATR), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) are employed. With the elevation of heat-treatment temperature, crystallinity progressively rises; at 450 °C, the microstructure retains amorphous traits featuring nanometric grains, whereas at 550 °C, heat-treatment results in fully crystallized structures characterized by square-shaped micron-scale grains of NaPO3. The insight into the evaluation of electrical and dielectric properties is provided by Solid-State Impedance Spectroscopy (SS-IS), revealing a strong correlation with the conditions of controlled crystallization and observed (micro)structure. The glass-ceramic heat-treated at 450 °C achieves the highest DC conductivity of 2.30×10–8 Ω–1 cm–1 at 393 K. As the heat-treatment temperature rises, the crystallization of the NaPO3 phase depletes the glass matrix of mobile Na+ ions, resulting in a reduction in DC conductivity. Dielectric parameters also decrease with rising heat-treatment temperature, with the glass-ceramic heat-treated at 550 °C displaying the lowest permittivity of 19.37 and the dielectric loss of 0.008. This research uncovers the intricate relationship between heat-treatment conditions and material properties, emphasizing that controlled crystallization allows for precise modifications to microstructure and phase composition within remaining glassy phase, ultimately facilitating fine-tuning of material properties.

Cardiovascular diseases (CVDs) and type 2 diabetes mellitus (T2DM) are two of the four major chronic non-communicable diseases (NCDs), representing the leading cause of death worldwide. Several studies demonstrate that endothelial dysfunction (ED) plays a central role in the pathogenesis of these chronic diseases. Although it is well known that systemic chronic inflammation and oxidative stress are primarily involved in the development of ED, recent studies have shown that perivascular adipose tissue (PVAT) is implicated in its pathogenesis, also contributing to the progression of atherosclerosis and to insulin resistance (IR). In this review we describe the relationship between PVAT and ED, and we also analyse the role of PVAT in the pathogenesis of CVDs and T2DM, further assessing its potential therapeutic target with the aim of restoring normal ED and reducing global cardiovascular risk.

The (benzylthio)acetic acid (HBTA) and some aminopyrimidines, namely 2-aminopyrimidine (2-AP), 5-aminopyrimidine (5-AP), 2-amino-4,6-dimethylpyrimidine (2-A-4,6-DMP) and 2,4,6-triaminopyrimidine (2,4,6-TAP), were successfully embodied as structural units into the construction of a total of four novel supramolecular organic frameworks. The received crystalline solids were inspected by single crystal X-ray diffraction (SC XRD) in order to obtain insight into the structural and supramolecular facets. The SOFs deriving from 2-AP, 5-AP as well as 2-A-4,6-DMP crystallize in the form of true co-crystals (1-3), while the one originating from 2,4,6-TAP crystallizes as salt solvate (4). The SC XRD results indicated the different contents of structural residues present in the asymmetric units of the crystals 1-4 despite the using the same molar ratio of molecular co-formers in each case. The molecular structures of co-crystals 1-3 consist of either one neutral residue of each starting components (1 and 3) or a half nonionized residue of aminopyrimidine ingredient and one neutral residue of acidic specie (2). The asymmetric unit of salt solvate 4 is composed of two ionized residues of each co-former (two 2,4,6-TAP+ cations and two BTA- anions) and one MeOH solvent molecule. The most extensive H-bonding network is observed in the crystal structure of salt solvate 4. The relevant molecular ingredients in co-crystals 1-3 are mainly hold together by the neutral Ocarboxylic–H···Npyrimidine and Namine–H···Ocarboxylic H-bonds. In the case of aggregate 4, the corresponding ionic residues are predominantly sustained by the charged-assisted Npyrimidinium–H···Ocarboxylate and Namine–H···Ocarboxylate hydrogen interactions. The MeOH solvent incorporated into the crystal lattice of adduct 4 is also involved in H-bonding by simultaneously serving as the single donor in OMeOH–H···S and the single acceptor in Namine–H···OMeOH H-bonds afforded the structural diversity within the 2,4,6-TAP+ cations and BTA- anions. Other weaker sets of additional non-covalent contacts existing in the crystal structures of analyzed conglomerates are involved in the self-assembly, stabilization and expansion of total supramolecular organic frameworks. The fact of the formation of non-covalent bonded supramolecular organic frameworks in question is also reflected in corresponding results obtained through elemental analysis (EA), Fourier transform infrared spectroscopy (FT−IR) and thermal analysis (TG/DSC).

The present study investigates the relationship between the local structure, photocatalytic ability, and cathode performances in sodium-ion batteries (SIBs) and lithium-ion batteries (LIBs) using Ni-substituted goethite nanoparticles (Ni_xFe_1-xOOH NPs) with a range of 'x' values from 0 to 0.5. The structural characterization was performed applying various techniques, including X-ray diffractometry (XRD), Thermogravimetry differential thermal analysis (TG-DTA), Fourier Transform Infrared Spectroscopy (FT-IR), X-ray absorption spectroscopy (XANES/EXAFS), both measured at room temperature (RT), and ⁵⁷Fe Mössbauer spectroscopy recorded at RT and at low temperatures (LT) from 20 K to 300 K, Brunauer-Emmett-Teller surface area measurement (BET), and diffuse reflectance spectroscopy (DRS). In addition, the electrical properties of Ni_xFe_1-xOOH NPs were evaluated by impedance spectroscopy. XRD showed the presence of goethite as the only crystalline phase in prepared samples with x ≤ 0.20, and goethite and α-Ni(OH)₂ in the samples with x > 0.20. Sample with x = 0.10 (Ni10) showed the highest photo-Fenton ability with a first-order rate constant value (k) of 15.8×10^-3 min^-1. The ⁵⁷Fe Mössbauer spectrum of Ni0, measured at RT, displayed a sextet corresponding to goethite, with an isomer shift (δ) of 0.36 mm s^-1 and a hyperfine magnetic distribution (B_hf) of 32.95 T. Moreover, the DC conductivity decreased from 5.52×10^-10 to 5.30×10^-12 (Ω.cm)^–1 with 'x' increasing from 0.10 to 0.50. Ni20 showed the highest initial discharge capacity of 223 mAh g^-1, attributed to its largest specific surface area of 174.0 m² g^-1. In conclusion, Ni_xFe_1-xOOH NPs can be effectively utilized as visible-light-activated catalysts and active cathode materials in secondary batteries.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

This research aimed to assess the influence of red dragon fruit peels ratio (RDF-PR) from two species, Hylocereus hybridum (HH) and Hylocereus undatus (HU), and particle size (PS) on quality parameters of red dragon fruit peel powder (RDF-PP), and its further application in emulsified alpaca-based sausages as partial substitutes of pork-back fat. A three-level full factorial design (nine treatments) was employed to evaluate the effect of: (i) RDF-PR [HH(0%):HU(100%), HH(50%):HU(50%), and HH(100%):HU(0%)] and (ii) PS (499–297, 296–177, and &lt;177 µm) on the dependent variables: L*, a*, b*, C, h°, water-holding capacity, oil-holding capacity, swelling capacity, pectin yield, degree of esterification (analysed through FT-IR), and crude fibre content. The data analysed through a response surface methodology showed that treatment one (T1) is the best with the optimised conditions at 100% HU RDF-PR and PS of &lt;177 µm. The statistical validation of T1 exhibited the highest water holding capacity (32.1 g H2O/g peel), oil holding capacity (2.20 g oil/g peel), and pectin yield (27.1%). A completely randomised design (four formulations) was then used to assess the effect of partial replacement of pork-back fat by T1 in emulsified alpaca-based sausages. The results revealed that 65.7% of pork-back fat content was successfully replaced as compared with a control formulation.

The investigation by the integrated approach newly introduced for this study indicates that insulin resistance (IR) would develop first preferentially in the muscle tissue with a relatively low cell turnover and then progress in sequence to the subcutaneous adipose tissue, to the visceral adipose tissue, and to the liver with higher cell turnovers. Moreover, metabolic disruptions due to IR vary widely from tissue to tissue, contrary to the conventional notion that IR merely impairs glucose uptake in the whole body. This warrants that IR be divided better into four distinct tissue specific IRs: muscle insulin resistance (MIR), subcutaneous adipose insulin resistance (s-AIR), visceral adipose insulin resistance (v-AIR), and hepatic insulin resistance (HIR). Tissue-specific IRs developing in the order of MIR, s-AIR, v-AIR, and HIR – producing tissue specific metabolic disruptions – would amount to nothing but the whole body insulin resistance (WBIR) evolving in four distinctively insulin resistant stages. The four stage metabolic evolution from rapid weight gain to visceral obesity to rapid weight loss to full blown diabetes not only complies well with the natural development history of diabetes but also resolves most of the controversies regarding obesity or diabetes, including visceral obesity, obesity paradox, and dawn phenomenon that have long remained metabolic puzzles. In addition, the four-stage WBIR evolution model refutes the entrenched notion of the lipid-induced insulin resistance (LIIR) but supports instead the glycation-induced insulin resistance (GIIR) proposed in this study. A speculation is that the glycation reaction activated ever more with WBIR evolving may serve as the common thread connecting each other a cluster of disorders or diseases that are often collectively referred to as the metabolic syndrome, such as obesity, diabetes, cardio/cerebral vasculopathy, nephropathy, neuropathy, and retinopathy.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

Increased screen time during the COVID-19 pandemic and the accelerated incorporation of technology into daily practices have directly contributed to the increased prevalence of eye disease. The human eye is not built for continual technological use and must adjust to exposure to digital screens. Overexposure to technology can result in eye strain and an increased risk of eye diseases such as myopia with complications later in life, including retinal tears, cataracts, and macular degeneration. As vision and ocular diseases become more prevalent, the study of eye diseases, including their causes and treatments, is especially relevant. There is a need to prevent ocular diseases before they become a burden to individuals, their families, and their communities by better understanding the pathophysiology of ocular diseases. Several ocular diseases are thought to be caused by imbalances in reactive oxygen species (ROS) and autophagy. ROS refers to a class of highly reactive oxygen-containing molecules that can undergo damaging reactions with other molecules in the cell. Autophagy is a cellular process of self-eating whereby damaged, harmful, or dead material in cells is broken down to maintain cellular homeostasis. This paper discusses the role of ROS and autophagy in the pathogenesis of computer vision syndrome (CVS), digital eye strain (DES), myopia, cataracts, glaucoma, diabetic retinopathy (DR), age-related macular degeneration (AMD), optic nerve crush injury (OCN), optic nerve gliomas, and retinoblastoma. Lifestyle changes such as limiting screen time, ensuring adequate exposure to evening sunlight, and using blue light protection measures or protective eyewear are important in the prevention of eye disease. Nutrition also contributes significantly to eye health. A balanced diet rich in vitamins and antioxidants may help to prevent ROS and autophagy imbalance-induced eye disease. Medical and surgical treatments become necessary when preventative measures fail. This paper also addresses how government measures to decrease the onset of eye disease, including targeted programs to increase access to fresh vegetables and fruits in food deserts, are a critical macro-level avenue to reduce eye disease prevalence in the US, which according to the National Eye Institute, costs $139 billion yearly.