A millimeter-wave (mmWave) gallium nitride (GaN) high-power amplifier (PA) monolithic microwave-integrated circuit (MMIC) was implemented, considering a source via effect. In this paper, we introduce guidelines for designing GaN high PA MMICs, from device sizing to meeting high-power specifications, power matching considering source via effects, schematic design of three-stage amplifier structures, and electromagnetic (EM) simulation. Based on the results of load pull simulation and small-signal maximum stable gain (MSG) simulation, the GaN high electron-mobility transistor (HEMT) size was selected to be 8×70 μm. However, since the source via model provided by the foundry was significantly different from the EM results, it was necessary to readjust the power matching considering this. Additionally, when selecting the source via size, the larger the size, the easier the matching, but since the layout of the peripheral bias circuit is not possible, a compromise was required considering the actual layout. To prevent in-band oscillation, an RC parallel circuit was added to the input matching circuit, and low-frequency oscillation was solved by adding a gate resistor on the PCB module. The proposed PA was fabricated with a commercial 0.1 μm GaN HEMT MMIC process. It exhibited 38.56 to 39.71 dBm output power (Pout), 14.2 to 16.7 dB linear gain, and 14.1% to 18.2% power-added efficiency (PAE) between 34 and 36 GHz. The fabricated GaN power amplifier MMIC shows competitive Pout in the Ka upper band above 33 GHz

In the history of high-performance polymer composite parts with continuous in-plane fibre reinforcement, the comparatively moderate structural-mechanical properties in their out-of- plane-z-direction and the limited load carrying capability between individual reinforcement layers within the laminated structures have always been one of the greatest challenges. Plenty of research work has been carried out to improve load transfer capability as well as fracture toughness for crack opening events between the reinforcement layers by means of out-of-plane fibre reinforcement implementation, for example by sewing or z-pinning technologies. However, the results have not become established across a wide range of applications so far, because the technologies used have led to considerable losses of in-plane strength properties. In this paper first results are presented for a new method of a low fraction z-fibre reinforcement by means of very thin diameter laser drilled holes filled with short carbon fibres, demonstrating potential to improve Mode II fracture toughness.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

The effects of soluble silicon fertilization on monocots and dicots have been widely studied. However, little is known regarding its effects on protecting epiphytes against insect and fungal pests. The efficacy of silicon fertilizer to reduce damage by thrip pest complexes, namely: Thrips palmi Karny, Frankliniella occidentalis Pergande, Chaetanaphothrips orchidii Moulton, and Chaetanaphothrips signipennis Bagnall (Thysanoptera: Thripidae), and fungal pathogens: Botrytis cinerea Persoon (Helotiales: Sclerotiniaceae) and Fusarium spp. Link (Hypocreales: Nectriaceae) was examined during a nine-month greenhouse trial in Hawaii. The trial assessed yield, quality, and pest damage across three common varieties of dendrobiums. All replicates received additional soluble silicon fertilizer applications alternating weekly between soil drench and foliar (50 mg Si/plant) applications. Yield, quality, and spray length, pest damage, plant vigor, SPAD, and leaf temperature were measured. Data were analyzed using a generalized linear model (glm) with repeated measures followed by post-hoc pair-wise comparisons in R, version 4.3.1. Treatment effects were significant at P

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

The inter-tip times (ITTs) of tipping-bucket rain gauges potentially provide the highest-resolution intensity data that can be acquired from this type of gauge. At an intensity of 100 mm h-1, a typical gauge with a sensitivity of 0.2 mm of rainfall would be expected to tip every 7.2 seconds. However, TBRGs are often equipped with syphons, to reduce the dynamic calibration error that results from continued (and unmeasured) inflow to a bucket as it tips. This increases the accuracy of rainfall depth recording, but the time to fill and empty the syphon can reduce the ability of a TBRG to respond to (and for the ITTs to reflect) short-term intensity fluctuations. This ability is already limited by the discretisation arising from the filling and emptying of the buckets themselves. Laboratory tests with controlled water inflow rates were performed using two high-quality TBRGs, one a 'straight-through' design and the other syphon-equipped. These confirmed that at all intensities at which the syphon operates, a regular sequence of fixed-duration ITTs (such as the 7.2 s mentioned above) does not occur. Rather, the ITTs are perturbed by the syphon cycling. The gauges were also co-located in the field, and linked to carefully synchronised event data loggers. Data collected during several rainfall events revealed differences in the ITTs, and again confirm that the ITT sequence of a syphon-equipped TBRG exhibits artefacts related to syphon operation, that are not present in the 'straight-through' data. These artefacts can result in ITT differences of many minutes, depending on the rainfall intensity, and are problematic for the use of ITTs to estimate intensity. Peaks and troughs in the intensity profile also differed between the two gauges. It is recommended that in the application of TBRGs for studies where short-term intensity data are required, 'straight-through' gauges should be used, and syphon-equipped gauges avoided.

The treatment of the bulky Rind-based dibromosilanes, (Rind)2SiBr2 (2) [Rind = 1,1,7,7-tetra-R1-3,3,5,5-tetra-R2-s-hydrindacen-4-yl: EMind (a: R1 = Et, R2 = Me) and Eind (b: R1 = R2 = Et)], with two equivalents of tBuLi in Et2O at low temperatures resulted in the formation of blue solutions derived from the diarylsilylenes, (Rind)2Si: (3). Upon warming the solutions above −20 °C, the blue color gradually faded, accompanying the decomposition of 3 and yielding the cyclic hydrosilanes (4) via intramolecular C−H bond insertion at the Si(II) center. The molecular structures of the bulky Eind-based 3b and 4b were confirmed by X-ray crystallography. Thus, at −20 °C, blue crystals were formed (Crystal-A), which were identified as mixed crystals of 3b and 4b. Additionally, colorless crystals of 4b as a singular component were isolated (Crystal-B), whose structure was also determined by an X-ray diffraction analysis. Although the isolation of 3 was difficult due to their thermally-labile nature, their structural characteristics and electronic properties were discussed based on the experimental findings complemented by computational results. We also examined the hydrolysis of 3b to afford the silanol, (Eind)2SiH(OH) (5b).

This article discusses how, in today’s world of disruptive and dramatic social change (DSC), non-sports related coaching, which includes a wide range of services such as life coaching, career coaching, executive coaching, and team coaching, can inadvertently fuel undesirable social dynamics. There is little or no awareness of this risk among coaches and coachees. The global, fast-growing, multi-billion-dollar industry aimed at supporting people and organisations to perform better and increase wellbeing while managing and adapting to change has been developed with limited sociological input. The article is based on 15 years of social constructionist-informed reflective practice by a sociologist-turned-coach, and uses a multi-layered autoethnographic account to argue for a sociologically informed paradigm shift in coaching, as well as relevant sociological knowledge and social and human sciences research methodology in coaches’ education. It presents the rationale and key features of a new coaching approach that places DSC-relevant sociological concepts at the heart of the coaching process, helps people develop psycho-sociological awareness, and uses a learning-to-develop through research design. A new definition of coaching to address DSC is derived. Coaching practitioners will find DSC-relevant sociological concepts, critical reflections, coaching questions, and procedures to expand coaching effectiveness. Interdisciplinary research topics combining coaching sociology and coaching psychology are suggested.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

Silicon Photomultipliers find applications across various fields. One potential Silicon Photomultiplier application domain is neutrino telescopes, where they may enhance the angular resolution. However, the elevated dark count rate associated with Silicon Photomultipliers represents a significant challenge to their widespread utilization. To address this issue, it is proposed to use Silicon Photomultipliers and Photomultiplier Tubes together. The Photomultiplier Tubes signals would serve as a trigger to mitigate the dark count rate, thereby preventing undue saturation of the available bandwidth. This paper presents an investigation into a fast and resource-efficient method for filtering Silicon Photomultiplier dark count rate. A low-resource and fast coincident filter has been developed, which removes the Silicon Photomultiplier dark count rate by using as trigger the Photomultiplier Tube input signals. The architecture of the coincidence filter, together with the first results obtained, which validate the effectiveness of this method are presented.

Nanocrystalline silicon oxide (nc-SiOx:H) is a multipurpose material with its varied application in solar cells as a transparent front contact, intermediate reflector, back reflector layer and even tunnel layer for passivating contacts, owing to easy tailoring of its optical properties. In this work, we systematically investigate the influence of gas mixture (SiH4, CO2, PH3 and H2), RF power and process pressure on the optical, structural and passivation properties of thin n-type nc-SiOx:H films prepared in an industrial, high throughput, plasma-enhanced chemical vapor deposition (PECVD) reactor. We provide a detailed description of the n-type nc-SiOx:H material develop-ment using various characterization techniques (SEM, EDX, Raman spectroscopy, and spectro-scopic ellipsometry) with a focus on the relationship between the material properties and the pas-sivation they provide to n-type c-Si wafers characterized by their effective carrier lifetime (τeff). Further, we also outline the parameters to be kept in mind while developing different n-type nc-SiOx:H layers for different solar cell applications. We report a tunable optical gap (1.8 – 2.3 eV) for our n-type nc-SiOx:H films as well as excellent passivation properties with τeff up to 3.5 ms (iVoc ~ 715 mV) before annealing. Oxygen content plays an important role in determining the crystallinity and hence passivation quality of the deposited nanocrystalline silicon oxide films.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

The protection of grapevine from the diseases is now particularly focused on the development of environmentally friendly strategies. Although sulphur is not in itself a toxic substance, a large use towards powdery mildew, in organic vineyards especially, may cause problems to environment, health and safety of viticultural workers and plant phytotoxicity. The activity on powdery mildew of sulphur applied at doses reduced up to 50% in tank mixtures with silicates and Equisetum arvense based products, never tested on grapevine, was assessed. Two-year trials were carried out applying the products every 7-9 days in the period of greatest risk for spring ascosporic infections, in two organic vineyards in the Abruzzo region, Italy. The effectiveness towards the disease of the mixtures was demonstrated, often to a greater extent than that of full-dose sulphur, normally used in the vineyards. Furthermore, in vines treated with the mixtures, increases in yield quantity and quality, such as higher contents of soluble solids and lower levels of total acidity, have been shown. Due to the strong efficacy demonstrated on the leaves, silicon-based products + sulphur mixtures can also be recommended in eradicative applications, aimed at reducing the inoculum of the disease. The great activity of the mixtures demonstrated in this study suggests confirmation through further investigations on different cultivars and vine-growing areas at different levels of infection, also testing the effectiveness of individual silicon products against the disease.

Helicobacter Pylori (H. Pylori) is a common pathogen with high prevalence of infection in human populations. Diagnosis of H. Pylori infection is critical for its treatment, eradication, and prognosis. Biosensors have been demonstrated to be powerful for rapid onsite detection of pathogens, particularly for point-of-care test (POCT) scenarios. In this work, we propose a novel optical biosensor, based on nanomaterial porous silicon (PSi) and photonic surface state Tamm Plasmon Polariton (TPP), for detection of cytotoxin-associated antigen A (CagA) antigen of H. Pylori bacterium. We fabricated the PSi TPP biosensor, analysed its optical characteristics and demonstrated through experiments towards sensing of CagA antigen, that TPP biosensor has sensitivity of 100 pm/(ng/ml), limit of detection of 0.01 ng/ml, and specificity in terms of positive-to-negative ratio of more than six. From these performance factors, it can be concluded that TPP biosensor can serve as an effective tool for diagnosis of H. Pylori infection, either in analytical labs or in POCT applications.

The evolution of photovoltaic cells is intrinsically linked to advancements in the materials from which they are fabricated. This review paper provides an in-depth analysis of the latest developments in silicon-based, organic, and perovskite solar cells, which are at the forefront of photovoltaic research. We scrutinize the unique characteristics, advantages, and limitations of each material class, emphasizing their contributions to efficiency, stability, and commercial viability. Silicon-based cells are explored for their enduring relevance and recent innovations in crystalline structures. Organic photovoltaic cells are examined for their flexibility and potential for low-cost production, while perovskites are highlighted for their remarkable efficiency gains and ease of fabrication. The paper also addresses the challenges of material stability, scalability, and environmental impact, offering a balanced perspective on the current state and future potential of these material technologies.

The possibility of using Si-based anodes in lithium-ion batteries is actively investigated due to the increased lithium capacity of silicon. The paper reports the preparation of submicron silicon fibers on glassy carbon in the KI–KF–KCl–K2SiF6 melt at 720°C. For this purpose, the parameters of silicon electrodeposition in the form of fibers were determined by cyclic voltammetry, and ex-perimental samples of ordered silicon fibers with an average diameter from 0.1 to 0.3 μm were obtained under galvanostatic electrolysis conditions. Using the obtained silicon fibers, anode half-cells of lithium-ion battery was fabricated, and its electrochemical performance under mul-tiple lithiation and delithiation was studied. By means of voltametric studies, it is observed that charging and discharging of the anode based on the obtained silicon fibers occurs at potentials from 0.2 to 0.05 V and from 0.2 to 0.5 V, respectively. A change in discharge capacity from 520 to 200 mAh g-1 during the first 50 charge/discharge cycles at a charge current of 0.1C and a Coulomb ef-ficiency of 98-100% was shown. The possibility of charging silicon-based anode samples at charging currents up to 2C was also noted; the discharge capacity ranged from 25 to 250 mAh g-1.

The sPHENIX experiment is a state-of-the-art jet and heavy flavor physics detector which successfully recorded its first Au + Au collision data at 200 GeV at RHIC. sPHENIX will provide heavy flavor physics measurements covering an unexplored kinematic region and unprecedented precision at RHIC to probe the parton energy loss mechanism, parton transport coefficients in quark-gluon plasma, and the hadronization process under various medium conditions. At the center of sPHENIX, the Monolithic-Active-Pixel-Sensor (MAPS) based VerTeX detector (MVTX) is a high-precision silicon pixel detector. The MVTX provides excellent position resolution and the capability of operating in continuous streaming readout mode, allowing precise vertex determination and recording a large data sample, both of which are particularly crucial for heavy flavor physics measurements. In this work, we will show the general performance of heavy-flavor hadron reconstruction. In addition, we will discuss the commissioning experience with sPHENIX. Finally, we will provide the projection of b-hadron and jet observables and discuss the estimated constraints on theoretical models.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.

The Reactive Spark Plasma Sintering (R-SPS) method is compared in this work with the two-steps SHS-SPS route, based on combination of the Self-propagating High-temperature Synthesis (SHS) with the SPS process, for the fabrication of dense (Hf0.2Mo0.2Ti0.2Ta0.2Nb0.2)B2-SiC and (Hf0.2Mo0.2Ti0.2Ta0.2Zr0.2)B2-SiC ceramics. A multiphasic and inhomogeneous product, containing various borides, is obtained at 2000°C/20min by R-SPS, from transition metals, B4C and Si. In contrast, if the same precursors are first reacted by SHS, and then processed by SPS under the optimized condition of 1800°C/20min, the desired ceramics are successfully attained. Both High-Entropy-Boride/SiC products display densities > 97%, uniform microstructures and contained only small amounts of residual oxides (<2.4 wt.%). The presence of SiC makes the sintering temperature milder, i.e. 150°C below to that needed by the corresponding additive-free system. Fracture toughness is also markedly improved, particularly when considering the Nb-containing system processed at 1800°C/20min, whereas KIC progressively decreases (from 7.35 to 5.36 MPa m1/2) as the SPS conditions become more severe. SiC addition is found to inhibit the volatilization of metal oxides like MoO3 formed during oxidation experiments, thus avoiding mass loss in the ceramics. The benefits above also likely take advantage of the fact that the two composite constituents are synthesized in parallel, according to the SHS-SPS approach, rather than being produced separately and combined subsequently, so that strong interfaces between them are formed.

The main objective was to analyze the influence of silicon content on high-temperature oxidation of low-alloy steels. Samples of AISI 1045, AISI 5160, and AISI 9254 steels, with different silicon contents, were oxidized at an isothermal temperature of 1000°C for times of 20 minutes, 40 minutes, and 60 minutes. The oxide layers formed mainly contain hematite, magnetite wustite, and fayalite. The average thickness of the oxide layer can decrease with an increase in silicon content below 1% but can increase for contents greater than 1% due to the difference in density between fayalite and iron oxides. Silicon tends to accumulate on the surface of steel and form a SiO2 film in the early stages of oxidation, which can control the oxidation process. The eutectic compound FeO+Fe2SiO4 forms at the oxide-steel interface, and its thickness increases with oxidation time and the silicon content present. The SiO2 film tends to decrease with oxidation time and silicon content.

Field-effect transistor (FET)-based biosensors stand as powerful analytical tools for detecting trace-specific biomolecules in diverse sample matrices, especially in the realms of pandemics and infectious diseases. The primary concern in applying these biosensors is their stability, a factor directly impacting the accuracy and reliability of sensing over extended durations. The risk of biosensor degradation is substantial, potentially jeopardizing sensitivity and selectivity and leading to inaccurate readings, including the possibility of false positives or negatives. This paper delves into the documented degradation of silicon nanobelt FET (NBFET) biosensors induced by buffer solutions. The results highlight a positive correlation between immersion time and the threshold voltage of NBFET devices. Secondary ion mass spectrometry analysis demonstrates a gradual increase in sodium and potassium ion concentrations within the silicon as immersion days progress. This outcome is ascribed to the nanobelt's exposure to the buffer solution during the biosensing period, enabling ion penetration from the buffer into the silicon. The study emphasizes the critical need to address buffer solution-induced degradation to ensure the long-term stability and performance of FET-based biosensors in practical applications.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

Semiconductors play a very important role in modern society. The improvement in performance of semiconductors is what has enabled the world to grow at such a fast pace. For decades scaling has been done through Moore’s law i.e performance improvements have been obtained due to transistor scaling where the number of transistors per unit area increase is what has contributed to the increase in performance. However, with transistor scaling reaching its limitations we need to find alternate methods to enhance silicon design to suit the computational need of modern society. To address this problem we will be looking into a few methods that enable performance scaling with a focus on analysing the most popular implementation of each in the industry.

The severe volumetric expansion of silicon nanoparticles (~400 %) limits their practical application as an anode material for next-generation lithium–ion battery (LIB). Here, we describe the fabrication and characterization of conformal polydopamine carbon shell encapsulating rattle-type silica@silicon nanoparticles (PDA−PEI@PVP−SiO2@Si) with tunable void structure prepared following a dual SiO2 template using (3–aminopropyl)triethoxysilane (APTES) as a self-catalytic, structure-directing agent to tetraethyl orthosilicate (TEOS) pretreated with polyvinylpyrrolidone (PVP K30) via modified Stöber process. Polyethylene imine (PEI) crosslinking facilitated the construction of interconnected three-dimensional bubble wrap-like carbon matrix structure through hydrothermal treatment, pyrolysis, and subsequent surface-protected etching. The composite anode material delivered 539 mAh·g−1 capacity after 100 cycles at 0.1 A·g−1, and 453 mAh·g−1 rate performance at 5 A·g−1. The satisfactory electrochemical performance of the PDA−PEI@PVP−SiO2@Si was attributed to the following: the rattle-type structure providing void space for Si volume expansion, PVP K30-pretreated APTES/TEOS SiO2 seeds via catalyst-free, hydrothermal-assisted Stöber protecting Si/C spheres upon etching, carbon coating strategy increasing Si conductivity while stabilizing the solid electrolyte interface (SEI), and PEI carbon crosslinks providing continuous conductive pathways across the electrode structure. The present work realizes a promising strategy to synthesize the tunable yolk–shell C@void@Si composite anode materials for high power/energy-density LIB applications.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of radio-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes were investigated. The main gas-phase and solid products of plasma-chemical transformations were determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems was carried out. It is shown that under the implemented experimental conditions, equilibrium components of the products are established. The detected spectra of chemical activity were studied, which gave reason to assume that the molecular mechanism of the hydrogen reduction process is the main one. The impurity composition of gas-phase and solid reaction products was investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, was shown.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

The work presented in this paper represents a preliminary study on the performance of the new Silicon tracker layer, the Layer 0 (L0), that will be installed on top of the Alpha Magnetic Spectrometer (AMS-02), at the end of 2024. AMS-02 is a cosmic rays (CR) detector that has been operating on the International Space Stations (ISS) since May 2011. Thanks to its 9-layer Silicon tracker, this apparatus can perform high energy CR measurements with an unprecedented level of statistics and precision. However, high Z (Z $\ge 15$) CR nuclei statistic is strongly affected by fragmentation along the detector: with the installation of the new Silicon layer will be possible to achieve new unique high energy (TeV region) measures for those nuclei along with increased statistics for all nuclei up to Zinc. To achieve this, a Silicon ladder prototype, that will be part of the final Silicon layer, has been exposed to an ions test beam at the super-proton-synchrotron (SPS) of the CERN to characterize its charge resolution and the readout electronics. Preliminary results have shown a charge resolution of 10 $\%$ for nuclei up to Z=7.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

The processes of hydrogen reduction of silicon and germanium chlorides under the conditions of high-frequency (40.68 MHz) counteracted arc discharge stabilized between two rod electrodes are investigated. The main gas-phase and solid products of plasma-chemical transformations are determined. Thermodynamic analysis of SiCl4 + H2 and GeCl4 + H2 systems for optimal process parameters was carried out. Using the example of hydrogen reduction of SiCl4 by the method of numerical modeling, gas-dynamic and thermal processes for this type of discharge are investigated. The impurity composition of gas-phase and solid reaction products is investigated. The possibility of single-stage production of high-purity Si and Ge mainly in the form of compact ingots, as well as high-purity chlorosilanes and trichlorogermane, is shown.

Tamm Plasmon Polariton (TPP) is a nanophotonic phenomenon that has attracted much attention due to its spatial strong field confinement, ease of mode excitation and polarization independence. TPP has applications in sensing, storage, lasing, perfect absorber, solar cell, nonlinear optics, and many others. In this work, we demonstrate a biosensing platform based on TPP resonant mode. Both theoretical analyses based on Transfer Matrix Method and experimental validation through nonspecific detection of liquids of different refractive indices and specific detection of SARS-CoV-2 nucleocapsid protein (N-protein) are presented. Results show that TPP biosensor has high sensitivity and good specificity. For N-protein detection, the sensitivity is 1.5 nm/(µg/ml) and the limit of detection can reach down to below 7 ng/ml with spectrometer of 0.01 nm resolution of wavelength shift. This work paves the way for design, optimization, fabrication, characterization, and performance analysis of TPP based biosensors

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

Background: The purpose of this study was to compare the immediate and long-term complications that are associated with the utilized techniques for the insertion of indwelling central venous catheters, that is the open surgical technique, the ultrasound-guided technique and the transcutaneous technique based on external anatomical landmarks in the right internal jugular vein, to a pediatric population. Methods: This was a prospective randomized trial based on a pediatric patient population, under 16 years of age, of a tertiary pediatric-oncological hospital. Procedure was performed by a medical team with varying experience regarding the percutaneous and open insertion methods. We studied the outcome of our procedure, based on the immediate and delayed complication rate, as well as the needed time in order to complete the procedure and mean duration of line use. Results: The patients that were inserted in our protocol were divided into three subgroups, based on the selected technique for the insertion of the central venous catheter. A total number of 88 insertions (25.4%) (out of 346) were based on the technique that was using external anatomical landmarks, 121 insertions were based on the ultrasound-guided transcutaneous technique (34,9%), whereas in 137 cases (39.5%) the open surgical technique was preferred. All cases that were related to catheter re-insertion were excluded from our study. We performed a statistical analysis regarding the catheter dwell time between the three subgroups of patients and no significant difference was recorded. Moreover, the development of thrombosis was investigated, and we mentioned that the higher percentage of this complication was related with the transcutaneous external landmark and open surgical technique. Also, the incidence of infection was taken into consideration, which manifested an increased incidence when the transcutaneous technique based on external landmarks was used. Conclusions: Ultrasound guided percutaneous insertion was considered to be a safe and effective technique for the insertion of central venous catheters. Our study also demonstrated a decrease in operating times, when performed by operators with increasing expertise, increased preservation of the diameter of the venous lumen, and no increase in complication rates when the ultrasound-guided technique was selected.

Public parks are a community resource with an important role in improving liveability, physical, and mental wellbeing. However, exercise facilities that are suitable for people with disabilities typically have been neglected in public park design. As such, people with disabilities often are unable to independently or safely use the park. To address this shortcoming, the objective of this paper was to employ a pragmatic research through designing process in developing the design for an inclusive park. We used a mixed-methods approach in the research that included review of previous studies, semi-structured interviews, and questionnaire surveys with stakeholders were applied as design integration. Persons with disabilities specifically were consulted to express their views on all matters of inclusive park design.

Intercalation of noble metals can produce giant Rashba-type spin-orbit splittings in graphene. The spin-orbit splitting more than 100 meV has not yet been achieved in graphene on a metallic or a semiconductor substrate. Here, we report the p-type graphene obtained by Pt intercalation of zero-layer graphene on SiC substrate. The spin splitting of ∼200 meV was observed at a wide range of binding energies. Comparing the results of theoretical studies of different models with the experimantal ones measured by spin-ARPES, XPS and STM methods, we came to the conclusion that inducing giant spin-orbit splitting requires not only a fairly close arrangement of graphene to Pt layer, but also the presence of graphene corrugation caused by non-flat Pt layer. This makes it possible to find a compromise between strong hybridization and increased spin-orbit interaction. In our case, this is achieved by forming Pt submonolayer ordered on a nanometer scale under graphene.

NUSES is a planned space mission aiming to test innovative observational and technological approaches related to the study of low-energy cosmic rays, gamma rays and high-energy astrophysical neutrinos. Two scientific payloads will be hosted onboard the NUSES space mission: Terzina and Zirè. Terzina will be an optical telescope readout by SiPM arrays, for the detection and study of Cerenkov light emitted by Extensive Air Showers generated by high-energy cosmic rays and neutrinos in the atmosphere. Zirè will focus on the detection of protons and electrons up to a few hundred MeV and to 0.1-10 MeV photons and will include the Low Energy Module (LEM). The LEM will be a particle spectrometer devoted to the observation of fluxes of low-energy electrons in the 0.1-7 MeV range and protons in the 3-50 MeV range along the Low Earth Orbit (LEO) followed by the hosting platform. The detection of Particle Bursts (PBs) in this Physics channel of interest could give new insight into the understanding of complex phenomena such as eventual correlations between seismic events or volcanic activity with the collective motion of particles in the plasma populating van Allen belts. With its compact sizes and limited acceptance, the LEM will allow the exploration of hostile environments such as the South Atlantic Anomaly (SAA) and the inner van Allen belt, in which are expected electron fluxes of the order of 106−7 cm−2 sr−1 s−1. Concerning the vast literature of space-based particle spectrometers, the innovative aspect of the LEM resides in its compactness, within 10x10x10 cm3, and in its “active collimation” approach dealing with the problem of multiple scattering at these very low energies. In this work, the geometry of the detector, its detection concept, its operation modes and the hardware adopted will be presented. Some preliminary results from the Monte Carlo simulation (Geant4) will be shown.

In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Bending waveguide is one of the building blocks of on-chip photonic integrated circuits (PICs). Previous bending waveguides (BWs) usually suffer from larger footprint size in the bending region, which is are not conducive to develop large-scale and high-density PICs. To this end, we propose and numerically investigate an ultra-compact silicon-on-insulator 180-degree waveguide bend with a bending radius of 2 µm. Being different from the previous BWs, the design is based on topologically optimized digital metamaterials, which is implemented by using intelligent genetic algorithms. Simulated results show that the proposed structure has a -1.36 dB bend efficiency per 180-degree at a wavelength of 1.55 µm and occupies a footprint of only 4 × 4 µm2. Moreover, the crosstalk is <−20 dB and the loss is <2.6 dB over a >100 nm operating bandwidth (1.6-1.7 µm) for TE0 modes. With the wide operating bandwidth and ultra-compact footprint, the proposed silicon-based 180-degree waveguide bend shows a potential application as the fundamental component for optical communication interconnect in the ultra-highly integrated photonic circuit.

Electro-optic modulator (EOM) is one of the key devices of high-speed optical fiber communication system and ultra-wideband microwave photonic system. Silicon-organic hybrid (SOH) integration platform combines the advantages of silicon photonics and organic materials, providing a high electro-optic effect and compact structure for photonic integrated devices. In this paper we present a SOH integrated EOM with comprehensive investigation of EOM structure design, silicon waveguide fabrication with Slot structure, on-chip poling of organic electro-optic material, and characterization of EO modulation response. The SOH integrated EOM is measured with 3dB-bandwidth of over 50 GHz and half-wave voltage length product of 0.26 V·cm. Furthermore, we demonstrate a microwave photonics phase shifter by using the fabricated SOH integrated dual parallel Mach-Zehnder modulator. The phase shift range of 410 degree is completed from 8 GHz to 26 GHz with a power consumption of less than 38 mW.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

porous silicon-based photodetectors have attracted more researches due to their high luminous efficiency, good stability and low cost. In this paper, a PbS quantum dots/porous silicon hybrid structure has been fabricated. The PbS quantum dots (QDs) partly infiltrated into the porous silicon (PSi) layer and partly deposited on its surface, which could increase the absorption of near-infrared wavelength range and extend the light absorption in silicon for wavelengths longer than 1100 nm. After that, A metal-semiconductor-metal (MSM) device is fabricated and its response spectrum could extend to the 1200 nm at -3 V. As a silicon-based photodetector (PD), one can envision its role for operation from visible light to short-wavelength infrared range.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

Changes in the atomic and electronic structure of silicon carbide 3C-SiC (β-SiC), resulting from lead adsorption, have been studied within the density functional theory. The tests were conducted for three representative surfaces with varying degrees of lead coverage. Results indicate that chemisorption occurs, with the strongest binding, found on the hexagonal surface (111) in interaction with three dangling bonds. The adsorption energy rises with increasing coverage, especially as the surface approaches saturation. Analysis of the data was focused on parameters important for corrosion processes such as bond distances, binding energies, Bader charges and charge density difference.

The microstructure of the coating during hot-dip galvanizing under industrial conditions of two structural steels, a low-silicon ASTM A36 steel and a high-silicon Q345B steel, both of commercial quality, have been characterized for industrial-relevant times. For both cases it is noted that the formation of the Fe-Zn phases begins in early stages during the heating of the steel, a situation in which all the phases are in the solid state. The characterization was carried out through traditional metallographic techniques including SEM-EDS and DRX equipment. The evolution in time of the microstructure of both steels is examined, being able to observe that the mechanism by which silicon accelerates the formation of Fe-Zn phases in galvanizing is related to the change in the energy of the interfaces caused by a silicon accumulation in the liquid phase in contact with the ζ layer. These results provided us with a deeper understanding of the phase evolution in the hot-dip galvanizing of high silicon steels.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

A significant electromotive force is induced in the rotor circuit of a doubly fed induction generator (DFIG) due to its high vulnerability to grid faults. Therefore, the system performance must be increased with appropriate control actions that can successfully offset such abnormalities in order to provide consistent and stable operations during grid disturbances. In this regard, this paper presents a solution based on a combination of an energy storage-based crowbar and a rotor-side crowbar that makes the effective transient current and voltage suppression for wind-driven DFIG possible. The core of the solution is its ability to restrict the transient rotor and stator overcurrents and DC-link overvoltages within their prescribed limits, aiming to protect the DFIG and power converters, and consequently, improve the system’ ability to ride-through faults. Further, the capacity of an energy storage device for transient suppression is estimated. Finally, simulation results show that the proposed approach is effective in achieving transient control objectives precisely and maintaining a stable grid connection during the faults.

Background: The popularity of climbing via ferratas (VF) in the European Alps has increased a lot. We have analysed the pattern of injuries from accidents, which have occurred on VF, and First Aid (FA) knowledge from the persons on such alpine routes. The aim was to create specific FA courses for those who climb VF. Material and Methods: Incidences and FA knowledge of the alpinists were investigated by a questionnaire. Data included details of the individual’s alpine experience, accidents or any kind of medical emergency they have ever experienced. FA knowledge was evaluated by 18 multiple choice questions with 5 answers each. The questionnaire was based on those of previous studies but was slightly adopted for VF. For this data from rescue operations on VF were used. Finally every participant was asked to judge his FA knowledge by a Likert scale (1 to 5). Results: The collective consisted of 391 participants (28.4% women) with an average age of 41 years. A significant portion did no regular fitness training and in most cases the last FA training was years ago. Nobody had joined a specific FA course for climbers or mountaineers. The most common causes of emergencies were: weather conditions (19%), stumble (18.6%), falls (13.4%), and weariness and deficiency in concentration (13.4%). FA questions most often answered correctly were cardiac emergencies (49.6%), high altitude cerebral edema (HACE) (43.2%), snow blindness (40.9%), injuries of the head (37.1%) and hemorrhagic shock (35.3%). Those most often wrong were injuries of the back (1.0%), injuries of the thorax (2.8%), frostbite (9.0%), acute mountain sickness (AMS) (4.1%) and strategy of rescue (4.1%). VF climbers show significant less FA knowledge than mountaineers in the Western Alps and trekkers. Conclusions: Data support the need of a specific FA training for VF climbers. Their FA knowledge does not fit with the demands in the mountains while some other knowledge they have is negligible on VFs (e.g. HACE). This is in accordance with earlier studies in “classic” alpine mountaineering and in trekking.

In this paper, we propose a novel approach to utilize silicon nanowires as high-sensitivity pH sensors. Our approach works based on fixing the current bias of silicon nanowires Ion Sensitive Field Effect Transistors (ISFETs) and monitor the resulting drain voltage as the sensing signal. By fine tuning the injected current levels, we can optimize the sensing conditions according to different sensor requirements. This method proves to be highly suitable for real-time and continuous measurements of biomarkers in human biofluids. To validate our approach, we conducted experiments, with real human sera samples to simulate the composition of human interstitial fluid (ISF), using both the conventional top-gate approach and the optimized constant current method . We successfully demonstrated pH sensing within the physiopathological range of 6.5 to 8, achieving an exceptional level of accuracy in this complex matrix. Specifically, we obtained a maximum error as low as 0.92\% (equivalent to 0.07 pH unit) using the constant-current method at the optimal current levels (1.71\% for top-gate). Moreover, by utilizing different pools of human sera with varying total protein content, we demonstrated that the protein content among patients does not impact the sensors' performance in pH sensing. Furthermore, we tested real-human ISF samples collected from volunteers. The obtained accuracy in this scenario was also outstanding, with an error as low as 0.015 pH unit using the constant-current method and 0.178 pH unit in traditional top-gate configuration.

The hydrodynamics of plasma formed in the interaction of 100-ns UV KrF laser pulses with foam targets with volume densities from 5 to 500 mg/cm3 was studied. Initial and dynamic transmittance at 248-nm wavelength have been measured. At intensities about 1012 W/cm2, the propagation rates of radiation through foam targets reached 80 km/s, while plasma stream velocities from both front and rear sides of targets were approximately the same ~ 75 km/s, which confirms a volumetric absorption of radiation within the target thickness and the explosive nature of the plasma formation and expansion.

Drought is an important factor seriously affects agricultural production worldwide. Agricultural practices that can increase resistance to drought are gaining importance. In this study the role of nano-silicon dioxide (NaSiO2) in countering drought stress in invitro strawberry plantlets were investigated. In the experiment, the effects of PEG 6000 concentrations (0, 4, 8%) and NaSiO2 concentrations (0, 50, 100 mg L-1) on invitro strawberry plants were determined. Plantlets treated with PEG 6000 showed reduced vegetative growth parameters, but this decrease was reduced with NaSiO2 application. NaSiO2 at 50 mg L−1 induced the maximum shoot and root fresh weight (1.20 g, 1.24 g, respectively) and length (40.09 mm, 34.26 mm, respectively), leaves number (16.67 pieces/plant) and SPAD index 53.57 among 4% and 8% PEG applications. When the SOD and CAT activities were examined, the results showed that application of NaSiO2 enhancement drought stress tolerance by promoted certain antioxidant response by increasing SOD and catalase (CAT) activities under drought stress. According to the results NaSiO2, limited the devastating impact of drought stress and markedly enhanced all the examined parameters.

Silicon has been proved to be one of the most promising anode materials for the next generation of lithium-ion battery. For the application in batteries, Si anode should have high capacity and must be industrially scalable. In this study, we have designed and synthesised a hollow structure to meet these requirements. All the processes are carried out without special equipment. The Si nanoparticles that are commercially available are used as the core sealed inside TiO₂ shell, with rationally designed void space between the particles and shell. The Si@TiO₂ are characterised using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The optimised hollow structured silicon nanoparticles, when used as anode in lithium-ion battery, exhibit a high reversible specific capacity over 600 mAhg-1. This excellent electrochemical property of the nanoparticles can be attributed to their optimised phase and unique hollow nanostructure.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

Oncological changes in the prostate are a common cause of death among elderly men. Malignant cells are difficult to identify at early stages, which are asymptomatic. The patient often seeks medical assistance when the disease has already progressed, and the treatment is less effective. Early diagnosis of prostate cancer (PC) is thus one of the priority tasks of modern urology and healthcare in general. The aim of this study is the detection of microRNAs (miRNAs), which are known to be associated with PC. The detection of the target miRNAs in human plasma samples has been performed with a nanoribbon biosensor system, which was based on "silicon-on-insulator" structures (SOI-NR biosensor). In order to provide biospecific detection of the target miRNAs, the surface of individual nanoribbons has been modified with DNA oligonucleotide probes (oDNA probes), whose nucleotide sequences were complementary to those of the target miRNAs. The high detection sensitivity has been demonstrated with the use of model oDNAs, which are complementary to nanoribbon-immobilized oDNA probes, in buffer solutions. The sensitivity threshold was 1.1 × 10^-17 M. The successful detection of target miRNAs, isolated from real plasma samples of PC patients, has also been demonstrated. We believe that the development of highly sensitive nanotechnology-based biosensors for PC markers is a step towards personalized medicine.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

We successfully created a composite photonic structure out of porous silicon (PSi) microcavities doped by the photochromic protein, photoactive yellow protein (PYP). Massive incorporation of the protein molecules into the pores was substantiated by a 30-nm shift of the resonance dip upon functionalization, and light-induced reflectance changes of the device due to the protein photocycle were recorded. Model calculations for the photonic properties of the device were consistent with earlier results on the nonlinear optical properties of the protein, whose degree of incorporation into the PSi structure was also estimated. The successful proof-of-concept results are discussed in light of possible practical applications in the future.

Amidst nature's enchanting embrace, forests stand as revered guardians, safeguarding biodiversity and nurturing rural livelihoods. In this journey, a qualitative study takes flight, exploring the cherished perspectives of the community within Iligan City's rustic expanse in Iligan City, Philippines. Its purpose? To unveil the intricate dance between forest conservation efforts and local livelihood strategies, weaving a tapestry of understanding. Through heartfelt conversations and keen observations, a diverse ensemble of 30 participants shares their wisdom, as thematic analysis reveals its breathtaking hues. In this symphony of voices, the community's resounding admiration for forest conservation emerges, painting a vivid portrait of its ecological significance and cultural splendor. As the canvas unfolds, the participants unfurl the whispered secrets of forest benefits—the gentle preservation of water resources and the enchanting pathways to ecotourism. Yet, amidst this beauty, they tenderly acknowledge the delicate trade-offs, where access to resources finds limitations. And so, the forest emerges as a steadfast companion in their livelihood odyssey, bestowing subsistence resources, opportunities for fruitful endeavors, and a profound sense of cultural heritage. These heartfelt discoveries beckon us to embrace the wisdom of the community, intertwining local perspectives into the fabric of forest conservation strategies, and championing participatory approaches that resonate with shared hopes and dreams. This study bestows upon us precious insights, illuminating the path towards sustainable forest management—a harmonious union where conservation goals and the vibrant tapestry of local livelihood needs dance hand in hand. Overall, locals must heed the profound symphony woven by forests and livelihood, as policymakers and practitioners craft a future where nature's melodies echo in the hearts of all who call the forest their home.

This study scrutinizes the complexities of designing and exploring the potential energy surface (PES) of systems containing more than twenty atoms with planar tetracoordinate carbons (ptCs). To tackle this issue, we utilized an established design rule to design a Naphtho [1,2-b:4,3-b′:5,6-b′′:8,7-b′′′]tetrathiophene derivative computationally. This process began with substituting S atoms with CH– units, then replacing three sequential protons with two Si2+ units in the resultant polycyclic aromatic hydrocarbon polyanion. Despite not representing the global minimum, the newly designed Si8C22 system with four ptCs provided valuable insights into strategic design and PES exploration. Our results underscore the importance of employing adequate methodologies to confirm the stability of newly designed molecular structures containing planar hypercoordinate carbons.

A structural study of the 6√3 reconstruction conversion on 4H-SiC substrate surface in an Ar medium with a short sublimation annealing time into quasi-free epitaxial graphene by means of hydrogen intercalation between the upper layer of SiC and the adjacent reconstructed layer was carried out using the technique of reflection high-energy electron diffraction (RHEED) characterizing the surface of a crystalline material. A slight violation of the 6√3 reconstruction layer formation uniformity was found. The results of the study of the crystal structure of quasi-free graphene and single-layer graphene comprising a buffer layer formed on 4H-SiC in the traditional way in an Ar atmosphere without intercalation were compared.

In this article, the biocatalytic oxidation of ethanol into acetaldehyde was studied using a catalase entrapped within monolithic polyampholyte cryogel, p(APTAC-co-AMPS), derived from an anionic monomer, 2-acrylamido-2-methyl-1-propanesulfonic acid sodium salt (AMPS), and a cationic monomer, (3-acrylamidopropyl) trimethylammonium chloride (APTAC) as catalyst. Macroporous polyampholyte cryogels containing various amounts of catalase were synthesized in situ under cryo-polymerization conditions at a molar ratio of monomers [APTAC]:[AMPS] = 75:25 mol.% in the presence of 10 mol.% cross-linking agent, N,N-methylenebisacrylamide (MBAA). The conversion of ethanol into acetaldehyde in good-to-high yields was observed in flow-through and batch type reactors under optimal conditions: at T = 10-20 C, pH = 7.1, [C2H5OH]:[H2O2] = 50:50 vol.%. According to SEM image the pore sizes of p(AMPS-co-APTAC) cryogel vary from 15 to 55 μm. The catalytic activity of catalase entrapped within monolithic polyampholyte cryogel in the conversion of ethanol into acetaldehyde was evaluated through the determination of such kinetic parameters as Michaelis constant (Km), the maximum enzymatic rate (Vmax), activation energy (Ea), turnover number (TON) and turnover frequency (TOF). The catalase encapsulated within monolithic polyampholyte cryogel exhibits a high conversion of ethanol into acetaldehyde. The advantages and disadvantages of flow-through and batch type reactors were highlighted.

The design and engineering of antibacterial materials is key for preventing bacterial adherence and proliferation in biomedical and house-hold instruments. Silver nanoparticles (AgNPs) and chitosan (CHI) are broad-spectrum antibacterial materials with different properties, whose combined application is currently under optimization. This study proposes the formation of antibacterial films with AgNPs embedded in carboxymethylcellulose/chitosan multilayers by the layer-by-layer (LbL) method. The films were deposited onto nanoporous silicon (nPSi), an ideal platform for bioengineering applications, due to its biocompatibility, biodegradability, and bioresorbability. We focus on two alternative multilayer deposition processes: cyclic dip coating (CDC) and cyclic spin coating (CSC). The physicochemical properties of the films were the subject of microscopic, microstructural and surface-interface analyses. The antibacterial activity of each film was investigated against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria strains as model microorganisms. According to the findings, CDC technique produced multilayer films with higher antibacterial activity for both bacteria compared to the CSC method. Bacteria adhesion inhibition was observed from only 3 cycles. The developed AgNPs-multilayer composite film offers advantageous antibacterial properties for biomedical applications.

Electrochemical deposition of silicon at room temperature is problematic due to intrinsically low conductivity of the deposits. This study reports the photoelectrochemical (PEC) deposition of silicon (Si) and silicon–carbon (Si–C) layers from an ionic liquid at temperature 40 oC using silicon tetrachloride (SiCl4) as a silicon precursor. Amorphous layers are deposited on p-type silicon (p-Si), p-type gallium arsenide (p-GaAs), and aluminum–copper alloy AA2024. The semi-conductor substrates are activated by white LED illumination, which generated photoelectrons, thereby making the substrate conductive with respect to the cathodic reaction. Photoresponsive-ness of the deposits is proven by the light-induced photocurrents on an optically inactive substrate made of the alloy AA 2024. The proposed method paves the way for the electrochemical modifica-tion of semiconductors and metals with Si and Si–C structures, which are applicable in various fields, such as; batteries, anti-corrosion coatings, photovoltaics, or PEC electrodes for hydrogen production.

This paper investigates the density, phase composition, microstructure and mechanical properties (microhardness, fracture toughness) of binderless WC + SiC ceramics obtained by conventional pressureless sintering (CPS) and Spark Plasma Sintering (SPS). α-WC nanopowders obtained by DC arc plasma chemical synthesis and β-SiC powders have been used as raw materials. The content of SiC particles was 1, 3, 5% wt. Excess graphite (0.3, 0.5% wt.) was added to α-WC nanopowders to decrease the volume fraction of W2C particles that negatively affect the mechanical properties of ceramics. WC + 1% wt. SiC + 0.3% wt. C ceramics are shown to have a homogeneous fine-grained microstructure, high relative density, increased microhardness and Palmquist fracture toughness. The CPS and SPS activation energies of WC + SiC nanopowders at an intensive shrinkage stage are determined using the Young-Cutler model. The effect of carbon and SiC particles on the CPS and SPS activation energies of tungsten carbide nanopowders has been analyzed. The CPS activation energies of WC, WC + C and WC + SiC + C nanopowders are shown to be closer to the carbon diffusion activation energy along α-WC grain boundaries. The SPS activation energies of WC and WC + SiC nanopowders turn out to be lower than the carbon grain boundary diffusion activation energy of α-WC.

Nowadays there is a need to increase the density of interconnections on printed circuit boards (PCBs). Does this mean that the only way out for quality PCB manufacturing is to proportional increase in precision of equipment, or is there another way? One of the main constraints to increasing the density of PCB interconnections is the transition holes. As the number of conductive layers increases, the number of vias increases and they cover a significant space on the PCB. On the other hand, reducing the size of the vias is limited by the capability of spatial alignment of the PCB stack during manufacturing. There are standards that set limits for the design of contact pads on a PCB (IPC-A-600G, IPC-6012B). However, depending on the precision of production, the contact pads may be of poor quality. This raises the issue of determining the reliability of a contact pad with defined parameters at the design stage, taking into account manufacturing capabilities. This research proposes an analytical method for evaluation of reliability of a via or plated through-hole based on calculation of its probability of production in accordance with the current standards. On the basis of the method a model was developed both for the case of a contact pad without any conductors connected to it (nonfunctional contact pad) and for the real case with a connected conductor. The model estimates the probability of making an acceptable via for a given reliability class depending on parameters such as the conductor width (minimum permissible and usable), drilled hole diameter and pad diameter, as well as the accuracy of the drilling operation. The analysis of the modeling results showed that for the real case, a reduction in the reliability class would insignificantly affect the probability of making an acceptable via due to the tight limitation on the connection place of the conductor and the contact pad. In conclusion, we propose an algorithm for determining the optimal parameters of teardrops to minimize the negative impact of the conductor on the reliability of the vias.

This article explores the cross-cultural significance of three iconic fairy tales: Cinderella, Snow White, and Sleeping Beauty. Using a comparative analysis approach, the study investigates recurring themes, motifs, and symbolism found in these tales across different cultures and time periods. The research draws on primary and secondary sources such as literary works and scholarly articles to uncover the underlying messages that resonate with audiences worldwide. The historical and cultural contexts of the tales are also examined to provide a deeper understanding of their significance in shaping cultural identity and values. The findings of the research demonstrate the enduring legacy of these tales and their continued relevance in contemporary society. The study highlights how the tales have evolved and adapted over time to reflect changing cultural values and beliefs. The interpretation of the findings offers insights into the role of storytelling in shaping cultural identity and values, and the ways in which these stories continue to inspire and captivate audiences worldwide. Overall, this research provides a comprehensive and nuanced understanding of the significance of these three fairy tales across cultures and time. By illuminating the similarities and differences in these tales, the study offers a fresh perspective on the power of storytelling and its ability to transcend cultural boundaries. The research contributes to the fields of folklore, cultural studies, and cross-cultural communication, inspiring further exploration into the captivating world of fairy tales.

Silicon-based thin-films and nanostructures are of paramount importance in a wide range of applications, including microelectronics, photovoltaics, large area sensors, as well as biomedicine. The wide accessibility of silicon and its relatively low cost have driven a continuous improvement of the technology based on this element. Plasma technology has been widely used for the synthesis of coatings and nanostructures based on silicon. Moreover, it has given a fundamental contribution for continuously improving the control of the physicochemical properties of silicon-based materials, and for allowing the synthesis of nanometric structures with well-defined shape and morphology. In this work, we have reviewed the most interesting developments of plasma-assisted processed for the synthesis of Si-based materials, both inorganic and organic, in the last five years. A special attention has been given to the new techniques, or modifications of already existing ones, that open new possibilities for the synthesis of materials with new properties, as well as nanostructures with novel characteristics.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

The importance of both recycling and additive manufacturing (AM) is increasing, however there has been a limited focus on development of AM alloys that are recyclably compatible with the larger scrap loops of wrought 5xxx, 6xxx and cast 3xx aluminium alloys. In this work the powder bed fusion (PBF) printability of AlMgSi alloys in the interval of 0-30wt%Mg and 0-4wt%Si is screened experimentally with a high throughput method. This method produces PBF mimicked material by PVD co-sputtering followed by laser remelting. Strong evidence was found for AlMgSi alloys being printable in two different composition ranges; Si+Mg<0.7wt% or for Si+2/3Mg>4wt% when Mg < 3wt% and Si > 3wt%. Increasing the amount of Mg and Si influence the grain structure by introducing fine columnar grains at the melt pool boundary, although the melt pool interior was unaffected. Hardness in as-built state increased with both Mg and Si, alt-hough Si had neglectable effect at low levels of Mg. Both evaporative loss of Mg and the amount of Mg in solid solution increased linearly with the amount of Mg.

Accurate measurement of low-level thoron gas and high-accuracy calibration of thoron measurement devices are essential for assessing and preventing thoron radiological risks. This study aimed to develop a thoron gas measurement technique using an airflow-through scintillation cell for both low-level measurement and high-accuracy calibration. To achieve this, a compartment model was developed to estimate the influence of progeny deposition and accumulation on the wall of the scintillation cell to prevent overestimation of thoron. A self-developed scintillation cell was utilized to implement and validate this technique. The lower detection limit and measurement uncertainty were then evaluated to assess the feasibility of the technique for low-level measurement and high-accuracy calibration. The results showed that the compartment model effectively addressed the influence of the progeny deposition. The measurement technique achieved a lower detection limit below 100 Bq m-3 even with the coexistence of 100 Bq m-3 of radon and attained a measurement uncertainty (k = 2) below 10% when the concentration of thoron exceeded 1,000 Bq m-3. In summary, this study developed a reliable and practical thoron gas measurement technique using an airflow-through scintillation cell with consideration for progeny deposition, and is expected to contribute to the assessment and prevention of thoron radiological risk.

conclusions. The blends of ultrahigh molecular weight polyethylene/polypropylene (UHMWPE/PP) possess excellent processability, but limited by its reduced mechnical properties. Herein, the high mechanical properties and wear—resistance UHMWPE/PP composites were fabricated by the addition of silicon carbide (SiC) nanoparticles under a consecutive elongational flow without any other additives or solvents. The morphology and thermal properties, mechanical properties, wear resistance as well as scratch resistance of UHMWPE/PP/SiC composites were investigated . The mechanical properties and friction resistance of composites increase initially then decrease with the increase content of SiC. The optimum mechanical properties of UHMWPE/PP/SiC composites are achieved when the content of SiC is 3 phr. In addition, both the hardness and scratch resistance of composites improved upon increasing the content of SiC. These improved mechanical properties and wear resistance originate from the well disperison of SiC nanoparticles along with favourable interfacial adhesive under a consecutive elongational flow.

: The paper presents the results of uniaxial tensile tests of samples of hypoeutectic aluminum-silicon alloy A319. According to the results of which the influence of surface treatment by a pulsed electron beam on the mechanical properties of the material was determined. The peculiarities of localization of deformation in the material, caused by grinding of the surface layer material structure due to rapid crystallization during electron beam treatment were revealed. The surface treatment up to 100 µm depth leads to the formation of a fine dendritic columnar structure of silumin and to an increase in the plasticity of the samples. The influence of surface treatment affects the increase of deformation localization in the region of stable concentrator before failure. The largest increase in ductility and localization of deformation occurs during processing with energy density of 15 J/cm2. In the process of specimen deformation, unstable, metastable, and stable areas of plastic deformation localization are formed and replaced, and the formation of stable areas of localized plastic deformation, in which the specimen fails at the end of the test, can be detected at the initial stages of testing. In specimens, during testing in the zone of localized plastic deformation, bands are formed that pass through the entire surface of the specimen at an angle from 35 to 55 degrees to the axis of tension, their evolution leads to the formation of stable zones of localized plastic deformation and to the failure of the specimen.

There are unsolved problems related to inflation, gravity, dark matter, dark energy, missing antimatter, and the birth of the universe. Some of them can be better answered by assuming the existence of aether and hypoatoms. Both were created during the inflation in the very early universe. While aether forms vacuum, hypoatoms, composed of both matter and antimatter and believed to be neutrinos, form all observable matter. In vacuum, aether exists between the particle-antiparticle dark matter form and the dark energy form in a dynamic equilibrium: A + A-bar = gamma + gamma. The same reaction stabilizes hypoatoms and generates a 3-dimensional sink flow of aether that causes gravity. Based on the hypoatom structure, the singularity does not exist inside a black hole; the core of the black hole is a hypoatom star or neutrino star. By gaining enough mass, ca. 3 X 10²² M_sun, to exceed neutrino degeneracy pressure, the black hole collapses or annihilates into the singularity, thus turning itself into a white hole or a Big Bang. The universe is anisotropic. Its center, or where the Big Bang happened, is at 0.66^+0.03_-0.01 times the radius of the observable universe at Galactic coordinates (l, b) = (286⁺¹⁰_-10, -43⁺⁷_-6). If we look from the Local Group to the center of the universe, the universe is rotating clockwise.

Recently, the interest in silicon-based detectors capable of detecting single photons in the near-infrared is growing mainly due to LiDAR applications, autonomous driving in particular. Silicon single-photon avalanche diodes are one of the most interesting single-photon NIR technology available on the market, nevertheless, their efficiency is hindered by the low absorption coefficient of Si in the NIR. The idea is the integration of CMOS-compatible nanostructures, specifically, silver grating array supporting Surface Plasmons Polaritons (SPPs), to confine superficially the incoming NIR photons and therefore increase photons probability to generate an electron-hole pair. The plasmonic silver array is geometrically fine-tuned using time domain simulation software to achieve maximum detector performance at 950 nm. Then, the plasmonic silver array is integrated by means of the focused ion beam technique on the detector. Finally, the integrated detector is electro-optically characterized, demonstrating a quantum efficiency of 13 at 950 nm, 2,2 times more than the reference detector. This result suggests the production of a device capable of detecting single NIR photons, at a very low cost and compatible with CMOS, thus integrable on existing technology platforms.

This computational research study will compare the specific charge capacity (SCC) between lithium ions inserted into crystallize silicon (c-Si) nanowires versus sodium ions inserted into amorphous silicon (a-Si) nanowires. It will be demonstrated that the potential energy V(r) within the lithium-silicon nanowire supports a coherent energy state model with discrete electron particles while the sodium-silicon nanowire potential energy will be discovered to be essentially zero and thus the electron current that travels through the sodiated silicon nanowire will be modeled as free electron with wave-like characteristics. This is due to the vast differences in the electric fields of the lithiated and sodiated silicon nanowires where the electric fields are of the order of 1e10 V/m and 1e-15 V/m respectively. The main reason for the great disparity in electric fields are due to the present of optical amplification within lithium ions and the absence of this process within sodium ions. It will be shown that optical amplification develops coherent optical interactions which is the primary reason for the surge of specific charge capacity in the lithiated silicon nanowire. Conversely, the lack of optical amplification is the reason for the incoherent optical interactions within sodium ions which is the reason for the low presence of SCC in sodiated silicon nanowires.

Silicon is an essential trace nutrient for plant growth and is frequently employed to remediate soils contaminated with heavy metals in agriculture. However, silicon’s role and mechanism in reducing heavy metal toxicity have not been well understood, especially for multi-heavy metals. In this study, the effects of silicon-rich materials (silicate, rice husk biochar (RHB), and bentonite) on growth trait, antioxidant response, and heavy metal accumulation and distribution of wheat grown in two soils polluted by multiple heavy metals (Cd, Zn, Pb, and As) were investigated. The results revealed that the addition of silicon-rich materials enhanced plant growth, improved the photosynthetic attributes in leaf tissues, and decreased the contents of Cd, Zn, Pb, and As in wheat shoots and grains. The examination of the subcellular distribution of heavy metals in plants implied that silicon-rich materials transferred heavy metals as intracellular soluble fractions to the cell walls, indicating the reduction of mobility and toxicity of heavy metals in the plants. In addition, the application of the silicon-rich materials reduced oxidative damage in plants by downregulating plant antioxidant response systems and decreasing the production of malondialdehyde (MDA), ascorbic acid (AsA), and glutathione (GSH). Moreover, fractionation analysis of soil heavy metals showed that silicon-rich amendments could convert bioavailable heavy metals into immobilized forms. The results indicated that silicon-rich materials could remediate multi-heavy metal-polluted soils and promote wheat production.

Background: The rise of cloud computing has led to the increasing number of organizations that rely on it for various tasks and services, such as education, healthcare, and e-commerce. Unfortunately, many security threats can be caused by the sudden use of cloud platforms. Objective: This paper aims to provide a comprehensive overview of these threats and how they can be mitigated. Many companies are moving toward cloud computing to sustain their business growth and provide their employees with the best possible work environment. Results: Due to the rise of cyber security threats and the unprecedented number of breaches of data, small and medium-sized enterprises are also starting to take a huge leap. The outbreak of COVID-19 has affected the lives of people all around the world. Conclusion: Due to the seriousness of the situation, the WHO has declared the COVID-19 pandemic a public health emergency. To minimize the spread of the virus, the entire world has started adopting social distancing

Silicon nanoparticles (SiNPs) are highly promising for biological and biomedical applications, including bioimaging, due to their unique opltical properties (i.e. strong fluorescence and very high photostability). Their low or negligible in vitro toxicity has been reported, but in vivo toxicity and biological effects of SiNPs are still uncertain. Uncoated SiNPs were dispersed in distilled water via sonication, and their rapid aggregation was observed (319.0 ± 2.4 nm particle size). In vivo toxicity was studied using Danio rerio embryos and larvae. Rapid aggregation in their incubation medium was observed; besides that, SiNPs at 25 mg/L or higher concentration induced swim bladder malformation and/or death of the fish. The estimated LC50 value for 7-day larvae was 180 mg/L. This is the first in vivo toxicity study of uncoated and unfunctionalized SiNPs. To achieve better stability in biological media and lower toxicity, SiNPs should be covered with hydrophilic layers, but their absorption by cellular membranes may be weaker in this case.

Silicon photonics is emerging as a competitive platform for electronic-photonic integrated circuits (EPICs) at the 2 µm wavelength band where GeSn photodetectors (PDs) have proven to be efficient PDs. Here, we present a comprehensive theoretical study of GeSn vertical p-i-n homojunction waveguide photodetectors (WGPDs) that have a strain-free and defect-free GeSn active layer for 2-µm Si-based EPICs. The use of a narrow-gap GeSn alloy as the active layer can fully cover entire the 2 µm wavelength band. The waveguide structure allows for decoupling the photon-absorbing path and the carrier-collection path, thereby allowing for simultaneous achievement of high-responsivity and high-bandwidth (BW) operation at the 2-µm wavelength band. We present the theoretical models to calculate the carrier saturation velocities, optical absorption coefficient, responsivity, 3-dB bandwidth, zero-bias resistance, and detectivity, and optimize this device structure to achieve highest performance at the 2-µm wavelength band. The results indicate that the performance of the GeSn WGPD has strong dependence on the Sn composition and geometric parameters. The optimally designed GeSn WGPD with 10% Sn concentration can give responsivity of 1.55 A/W, detectivity of 6.12×1010 cmHz½W-1 at 2 µm wavelength, and ~97 GHz BW. Therefore, this optimally designed GeSn WGPD is a potential candidate for silicon photonic EPICs offering high-speed optical communications.

We experimentally demonstrate enhanced spectral broadening of femtosecond optical pulses after propagation through silicon-on-insulator (SOI) nanowire waveguides integrated with two-dimensional (2D) graphene oxide (GO) films. Owing to the strong mode overlap between the SOI nanowires and the GO films with a high Kerr nonlinearity, the self-phase modulation (SPM) process in the hybrid waveguides is significantly enhanced, resulting in greatly improved spectral broadening of the femtosecond optical pulses. A solution-based, transfer-free coating method is used to integrate GO films onto the SOI nanowires with precise control of the film thickness. Detailed SPM measurements using femtosecond optical pulses are carried out, achieving a broadening factor of up to ~4.3 for a device with 0.4-mm-long, 2 layers of GO. By fitting the experimental results with theory, we obtain an improvement in the waveguide nonlinear parameter by a factor of ~3.5 and the effective nonlinear figure of merit (FOM) by a factor of ~3.8, relative to the uncoated waveguide. Finally, we discuss the influence of GO film length on the spectral broadening and compare the nonlinear optical performance of different integrated waveguides coated with GO films. These results confirm the improved nonlinear optical performance for silicon devices integrated with 2D GO films.

The use of cobalt-iron (VaCoFe) core is investigated as an alternative to silicon-iron (FeSi) on the design of interior permanent magnet synchronous motors (IPMSM). A spoke-type IPMSM geometry is optimized considering FeSi and VaCoFe cores for a torque range up to 40 N.m, providing a general comparative analysis between materials, considering the application of a 4-motor competition vehicle’s powertrain. A genetic optimization algorithm is applied over a hybrid analytical/finite-element model of the motor to provide sufficiently accurate electromagnetic and thermal results within a feasible time. VaCoFe can result in an estimated increase of up to 5 % in efficiency for the same torque, or up to 64 % torque increase for the same efficiency level. After optimization, and using a detailed time-dependent model, a potential 3.2 % increase in efficiency, a core weight reduction of 4.1 %, and a decrease of 9.6 % in the motor’s core volume was found for the VaCoFe at 20 Nm. In addition, for the same motor volume, the VaCoFe allows an increase of 51.9 % of torque with an increase of 1.1 % of efficiency, when compared with FeSi.

: Nanotechnology options to road surface maintenance offers several advantages compared to traditionally used materials. The small particle sizer of hydrophobic Nano-Silane modified Nano-Polymers (NSNP) enables these nanotechnology products to deeply penetrate existing road surfaces, sealing micro-cracks and render surfacings to be water-resistant for extended periods of time. In comparison, traditionally used products contain minimum partial sizes of about 1 – 5 microns, that provide a superficial protection that wears off in a relatively short period of time. These traditional products are often associated with vehicle contamination while drying and requires the re-instatement of road markings. None of these disadvantages are associated with applicable NSNP technologies that are quick drying, with no vehicle contamination risks and is equivalent to a “clear-seal” requiring no reinstatement of road markings. In a similar vein, pot-hole repairs can be done using applicable, easy to use, pre-packed and treated pot-hole repair kits that are water-repellent and quick-drying at a fraction of the costs of conventional cold-mix products. Resurfacing using NME binder slurries can be done labour-intensively on a pre-treated NSNP surfacing, restoring cracked surfacing and providing a water-resistant long-lasting protective layer without the removal of existing cracked areas. The implementation of nanotechnology solutions for road surface maintenance operations is directly associated with ease of use, labour-intensive operations, prevention of considerable deterioration in riding quality due to removal and manual re-instatement of cracked surfaces, time and cost savings and a reduction in the risk of water damage to the sub-structure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Self-healing is the capability of materials to repair themselves after damage has occurred, usually by interaction between molecules or chains. Physical and chemical processes are applied for the preparation of self-healing systems. There are different approaches for these systems such as heterogeneous systems, shape memory effects, hydrogen bonding or covalent-bond interaction, diffusion and flow dynamics. Self-healing mechanisms can occur in particular by heat and light exposure or by reconnection without direct effect. The applications of these systems display an increasing trend in both R&D and industry sectors. Moreover, self-healing systems and their energy storage applications are currently getting great importance. This review aims to provide general information on recent developments in self-healing materials and their energy applications in view of the critical importance of self-healing systems for lithium-ion batteries (LIBs). In the first part of the review, an introduction about self-healing mechanisms and design strategies of self-healing materials is given. Then, selected important healing materials in the literature for the anodes of LIBs are mentioned in the second part. The results and future perspectives are stated in the conclusion section.

Volcanic fumaroles are openings in the earth's surface, where volcanic gases discharge to the atmosphere. Metallic and non-metallic elements contained in gases form specific mineral precipitates upon cooling. Although the presence of metals in fumarolic gases has long been known, their concentrations are generally low and difficult to measure directly. A laboratory model of a fumarole may resolve the situation if the complex gas composition could be accurately reproduced. Here we describe a new experimental approach that allows accurately simulating fumarolic gases in terms of their main components (H₂O, CO₂, S, HCl), as well as adding volatile metal compounds. Gas is generated inside a special flow-through reactor, at the outlet of which the elements contained in the gas form temperature-dependent mineral sequence inside the attached silica-glass tube. Using this installation, we obtained laboratory sublimates from reducing (H₂S-rich) gases similar to natural ones in terms of mineral composition and mineral habits. Twenty-one phases have been identified in sublimates, among which are simple and complex chlorides, simple sulfides and six sulfosalts. Comparison of the sublimate deposition from H₂O-rich gas at 1 bar with similar works performed in evacuated ampoules at low pressure showed that fumarolic gases behave like an ideal gas, in which molecules do not interact with each other, and reactive compounds in the gas serve in fact as an inert carrier of volatile metals species. Changing the composition of the gas at the outlet of the installation, its flow rate and temperature, we can observe the corresponding changes in mineral precipitates and in such a way study the factors affecting mineral formation on natural fumarolic fields.

This paper presents a low-cost C-band frequency-modulated continuous wave (FMCW) radar system for use in indoor through-wall metal detection. Indoor remote-sensing applications, such as through-wall detection and positioning, are essential for the comprehensive realization of the internet of things or super-connected societies. The proposed system comprises a two-stage radio-frequency power amplifier, a voltage-controlled oscillator, circuits for frequency modulation and system synchronization, a mixer, a 3-dB power divider, a low-noise amplifier, and two cylindrical horn antennas (Tx/Rx antennas). The antenna yields gain values in the 6.8 ~ 7.8 range when operating in the 5.83 ~ 5.94 GHz frequency band. The backscattered Tx signal is sampled at 4.5 kHz using the Arduino UNO analog-to-digital converter. Thereafter, the sampled signal is transferred to the MATLAB platform and analyzed using a customized FMCW radar algorithm. The proposed system is built using commercial off-the-shelf components, and it can detect targets within a 56.3 m radius in indoor environments. In this study, the system could successfully detected targets through a 4-cm-thick ply board with a measurement accuracy of less than 10 cm.

This research will examine the computational methods to calculate the nonlinear optical process of second harmonic generation (SHG) that will be hypothesized to be present during lithium ion insertion into silicon nanowires. First it will be determined whether the medium in which SHG is conveyed is non-centrosymmetric or whether the medium is inversion symmetric where SHG as a part of the second-order nonlinear optical phenomenon does not exist. It will be demonstrated that the main interaction that determines SHG is multiphoton absorption on lithium ions. The quantum harmonic oscillator (QHO) is used as the background that generates coherent states for electrons and photons that transverse the length of the silicon nanowire. The matrix elements of the Hamiltonian which represents the energy of the system will be used to calculate the probability density of second-order nonlinear optical interactions which includes collectively SHG, sum-frequency generation (SFG) and difference-frequency generation (DFG). As a result it will be seen that at varies concentrations of lithium ions (Li+) within the crystallized silicon (c-Si) matrix the second-order nonlinear optical process has probabilities substantial enough to create second harmonic generation that could possibly be used for such applications as second harmonic imaging microscopy.

The efficiency of data sorting algorithms is the key aspect which determines the speed of data processing and searching. The best known efficiency of sorting algorithm has been Log (N) if there are N terms. All of the well-known sorting algorithms use various techniques to sort data. The basis for most of these are comparing the data terms with each other. In this manuscript, we are introducing a new approach for sorting data. This method is postulated to have the highest efficiency ever achieved by any of the sorting algorithms. We achieve this by sorting data without comparing the data terms. Or achieving results of data comparison without comparing the terms explicitly.

We present the results on photothermal (PT) and heat conductive properties of nanogranular silicon (Si) films synthesized by evaporation of colloidal droplets (drop-casting) of 100 ± 50 nm sized crystalline Si nanoparticles (NP) deposited on glass substrates. Finite difference time domain (FDTD) and finite element mesh (FEM) modeling of absorbed light intensity and photo-induced spatial temperature distribution across the Si NP films were well correlated with the local temperatures measured by micro-Raman spectroscopy and used for determination of heat conductivities in the films of various thicknesses. Cubic-to-hexagonal phase transition in these films caused by laser heating was found to be heavily influenced by the film thickness and heat conductive properties of glass substrate, on which the films were deposited. Heat conductivities across the drop-casted Si nanogranular films were found to be in the range of lowest heat conductivities of other types of nanostructurely voided Si films due to enhanced phonon scattering across inherently voided topology, weak NP-NP and NP-substrate interface bonding within nanogranular Si films.

Hydrogenated amorphous silicon (a-Si:H) can be produced by plasma-enhanced chemical vapour deposition (PECVD) of SiH4 (Silane) mixed with Hydrogen. The resulting material shows outstanding radiation resistance properties and can be deposited on a wide variety of different substrates. These devices have been used to detect many different kinds of radiation namely: MIPs, x-rays, neutrons and ions as well as low energy protons and alphas. However, MIP detection using planar diodes has always been difficult due to the unsatisfactory S/N ratio arising from a combination of high leakage current, high capacitance and a limited charge collection efficiency (50% at best for a 30 µm planar diode). To overcome these limitations the 3D-SiAm collaboration proposes to use a 3D detector geometry. The use of vertical electrodes allows for a small collection distance to be maintained while conserving a large detector thickness for charge generation. The depletion voltage in this configuration can be kept below 400 V with consequent reduction in the leakage current. In this paper, following a detailed description of the fabrication process, the results of the tests performed on the planar p-i-n structures made with ion implantation of the dopants and with carrier selective contacts will be illustrated.

Doubly Fed Induction Generator (DFIG) has a stator winding directly coupled with grid. Whereas, rotor winding is connected via a fault-prone back to back power converters. DFIG is known to be vulnerable to the grid faults. In early times, when a fault occurred, these generators were required to disconnect from the grid to secure the generator and power converters. However, due to the increased penetration of wind turbines into the power system, grid operators demanded that the wind turbines remain connected to the grid, as disconnecting them would further disrupt the grid. When a fault at the grid terminal occur, a high stator current is induced which further result in high rotor current. This current will trigger the DC-link voltage to rise. This high currents and DC-link voltage will cause harm to the converters. Thus, in this paper work, the crowbar protection system is employed for protecting the converters against excess energy. Furthermore, the analysis of DFIG is rendered by integrating the crowbar protection with the Battery Energy Storage System (BESS) for a much effective outcome in enhancing machine to drive the fault. MATLAB-Simulink software is used for modeling and simulation. All system parameters are obtained from ADAMA-II Wind Farm.

The fabrication of thin-film multilayer structures by sputtering technique usually requires multi-cathode deposition machine. This study proposes a simpler approach based on the RF power modulation: silicon nitride (SiN$_x$) thin films were prepared by RF reactive sputtering in (Ar + N$_2$) atmosphere at room temperature. The samples were analyzed to highlight the effects of different deposition conditions on the morphological and optical properties of the films in the visible and near/mid-IR regions. The refractive index of the films was changed in the range of 1.5 - 2.5 (at $\lambda$=800 nm) by tuning the sputtering power. IR reflectance measurements revealed the absence of spurious (oxygen- or hydrogen-based) phases, while atomic force and scanning electron microscopies confirmed the presence of flat and defect-free samples surfaces.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

We report a micro-ring resonator with adiabatic bends, non contact waveguide heaters and small bend radius. The ring has the lowest reported off resonance loss and can support 8 wavelength division multiplexed channels at 200 GHz spacing. We measure 0.49 nm/mW tuning efficiency and 0.085 dB off resonance loss.

A distributed bragg reflector is designed to get an optical reflectance on visible electromagnetic spectrum i.e. ~800 nm in this work. Device is realized based on Abele’s matrix for TE mode.

The tandem Solar cell has high power conversion efficiency (PCE), so they are taken as the next step in photovoltaic evolution. The tandem solar cell also overcome the limitations of Single-junction solar cells by reducing thermalization losses and also reduce the fabrication cost. The fabrication of tandem solar cells is highly efficient after the origination of halide perovskite absorber material, this material will shape the future of tandem solar cells. Researchers have already shown that this material can convert light more efficiently than standalone sub cell. Today, researchers around the world are keeping the configuration of a tandem solar cell as their agenda. A Tandem solar cell is a stacking of multiple layers having different bandgaps with specific maximum absorption and width. We reviewed perovskite/silicon tandem solar cells with different sub-module configurations. Move forward, we discuss the tandem module technology, sub cell of a tandem can be wired in several ways two terminals 2T monolithic and mechanically stacked, a four-terminal 4T mechanically stacked, and three-terminal 3T monolithic stack devices. This review paper provides a side-by-side comparison of theoretical efficiencies of multijunction solar cells. The highest efficiency has been evaluated at 39.4% for a three-level structure.