The rapid growth of the Information and Communications Technology (ICT) sector requires additional infrastructure, such as more micro-datacenters and telecom stations, to support the higher internet speeds and low latency requirements of 5G net-works. The increased power requirements of the new ICT technologies necessitate the proposal of new power supplies in an attempt to retain the increase in energy demand and running costs. This work provides an in-depth theoretical analysis on the losses of the individual stages of commercially available PSU and proposes a new multicell PSU, Buck-PFC converter, which offers a higher overall efficiency at varying load levels. The theoretical results are verified using simulation results, via PSIM Thermal Module, and using experimental data. The results indicate that multi-cell structures can improve the overall PSU ef-ficiency by 1.2% at 50% rated power and more than 2.1% at full power. Finally, taking into consideration the economic implica-tions of this study, it is shown that the proposed multicell structure may increase the PSU costs by 10.78% but the payback pe-riod is in the order of just 3.3 years.

Substantial research is required to ensure that micro-mobility ride sharing provides a better fulfillment of user needs. This study proposes a novel crowdsourcing model for the ride-sharing system where light vehicles such as scooters and bikes are crowdsourced. The proposed model consists of three entities: suppliers, customers, and a management party responsible for receiving, renting, booking, and demand matching with offered resources. It can allow suppliers to define the location of their private e-scooters/e-bikes and the period of time they are available for rent. Using a dataset of over 9 million e-scooter trips in Austin, Texas, we ran an agent-based simulation six times using three maximum battery ranges (i.e., 35, 45, and 60 km) and different numbers of e-scooters (e.g., 50 and 100) at each origin. Computational results show that the proposed model is promising and might be advantageous to shift the charging and maintenance efforts to a crowd of suppliers.

Minerals play many important functions in plant and animal metabolism. Therefore, we investigated the concentration of Se and other minerals and their relationships in soils and fodder plants in Kosovo. Seventy-three samples of each soil and fodder plants (grass, maize, and wheat) from 30 farms were collected. Both soil and plant samples, after processing and digestion, were analyzed for mineral concentration by ICP-MS. Mineral concentrations in soil and fodder crops, and the best predicting/explanatory models for micro minerals concentration, achieved by stepwise linear regression, are presented. Results showed very low concentration of Se in most of the soil and all fodder samples. In addition, the concentration of Co, Zn and Fe was not sufficient to satisfy requirements for all categories of farm animals. Plant Se concentration showed a positive relationship with Se concentration in soils. Plant Zn, Mo, Mn, Fe and Pb, in general, showed no significant relationship with their concentration in soil, while plant Co and Cd showed positive relationship only in maize, and Cu in wheat grain. Among the soil properties, pH had the highest effect on the concentrations of Co, Mo, Mn, Cd and Pb in fodder crops.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

Biological micro-dissection has a wide range of applications in the field of molecular pathology. The current laser-assisted dissection technology is expensive, and laser radiation can lead to sample contamination. As an economical and pollution-free micro-dissection method, piezoelectric ultrasonic micro-dissection has a wide application prospect. However, the performance of the current piezoelectric ultrasonic micro-dissection technology is unsatisfactory. In this paper, a novel piezoelectric ultrasonic micro-dissection device based on a flexure mechanism is proposed in order to solve the problems of low dissecting precision and excessive wear of the dissecting needle caused by the harmful lateral vibration of the current piezoelectric ultrasonic micro-dissection device. By analyzing the flexibility of flexure hinge, the type of flexure beam and the optimal design parameters are determined. Through comparing the harmonic response simulation analysis of the micro-dissection device based on a flexure mechanism and the traditional micro-dissection device without the flexure mechanism, the newly designed micro-dissection device achieves the best vibration effect when the driving frequency is 28kHz, compared with the traditional micro-dissection device, the lateral vibration suppression effect is improved by 68%. Then, based on the 3D printing technology, a prototype of a novel micro-dissection device was produced, and its performance was tested. It was found that the flexure mechanism did indeed suppress the lateral vibration of the needle tip. Finally, the experiments of 5μm thick paraffin-embedded rat liver sections were carried out, and the effects of different dissecting parameters on the dissecting effect were analyzed, and the optimal dissecting parameters were obtained. By comparing the dissecting effects of the tissue sample and the wear condition of the needle tip between the novel micro-dissection device and the traditional micro-dissection device under their optimal dissecting parameters, it is proved that the suppression of harmful lateral vibration not only significantly improves the dissecting effect, but also improves the service life and durability of the dissecting needle, which is beneficial to reduce the equipment costs.

The flipped classroom is gaining prominence as an active learning pedagogy to engage a new generation of students. However, all courses do not lend themselves to a fully flipped design and instructors are often reluctant to flip lectures. In this study, I experimented with a “partial” flipped classroom design in a first-year undergraduate economics course. In this partial flipped format, traditional lectures were substituted with micro-lectures and the remaining class time was devoted to activities like quizzes, group work and student presentations. The full lectures were panopto recorded and put up on the e-learning site, Blackboard. This format enabled me to combine the benefits of a traditional lecture with a flipped classroom design. In order to evaluate the effectiveness of the partial flipped classroom format, I compared the final exam scores of students in the partial flipped classroom with those in the control group, which followed a traditional lecture-based approach. The key results from the analysis revealed that students in the partial flipped classroom performed better in the final exams vis-à-vis students in the traditional classroom format. Furthermore, the partial flipped classroom format was associated with lower odds of students failing in the module. This format also resulted in better student engagement, more flexibility and enhanced student-tutor interaction within the classroom.

The Neotropical region is one of the most diverse regions of the globe in terms of macro-organismic species. Regarding the microbial world, however, little is known about the diversity and biogeography patterns of micro-organisms in the Neotropics. In this context, the study of several microbial taxonomic groups is still missing and/or incomplete, such as the protists. Our goal here was to summarize the available information of Neotropical protists, focusing on molecular data from environmental continental samples, to explore what these data evidence on their ecology and biogeography. For this, we reviewed the findings from all articles that focused on or included the terrestrial protists using metabarcoding approach and identified the gaps and future perspectives in this research field. We found that Neotropical protists diversity patterns seem to be, at least in part, congruent with that of macro-organisms and, different than plants and bacteria, just weakly explained by environmental variables. We argue that studies with standardized protocols including different biomes are necessary to fully characterize the ecology and biogeography on Neotropical protists. Furthermore, dismember evolutionary lineages and functional guilds of protists are important to better understand the relationship between diversity, dispersal abilities and functionality of particular taxa of protists in their habitats.

This study evaluated the mechanical strengths of three types of orthodontic micro-implants by analyzing their structural configurations. Thirty micro-implants of three types (diameter 1.5 mm, Types A, B, C) were assessed. All micro-implants were manually driven into artificial bones at an 8-mm depth. The insertion torque (IT), pullout strength (PS), and gripping volume (GV) of each type were measured. Intergroup comparisons and intragroup correlation were investigated by statistical analysis. Type B had the greatest inner–outer diameter ratio (0.67), and Type A had the smallest (0.53). The IT of Type A (5.26 Ncm) was significantly (p = 0.038) lower than that of Type C (8.8 Ncm). There was no significant difference in the pullout strength (p = 0.868). The GV of Type A (9.7 mm3) was significant (p < 0.01) greater than Type C (8.4 mm3). Type C was significant (p < 0.01) greater than Type B (7.2 mm3). Spearman’s rho rank correlation test showed that PS of Type B was correlated significantly with GV. In conclusion, the design of thread and its GV were the important factors on the mechanical strengths of micro-implant.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

Natural events such as floods, fires, tsunamis, earthquakes and others have nowadays caused serious damage to human beings and nature. The precise detection of these natural events and especially the earthquake has nowadays become the focus of many computer and geoscientific researchers. Computer science and machine learning algorithms have revolutionized early detection and prediction of these events. Hence, a fuzzy method has been initially used in this article to enhance the authenticity of data based on application of effective variables and then combination of neural network algorithms of the MLP perceptron and radial network of RBF in form of a collective learning system in order to more accurately identify seismic events on a small scale. It was observed after simulating the proposed method that the proposed method has significantly improved based on actual error and root-mean-square error (RMSE) criteria compared to basic methods.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Shear connectors are used in steel beam–concrete slabs of composite frame and bridge structures to transfer shear force according to design loads. The existing Y-type perfobond rib shear connectors are designed for girder slabs of composite bridges. Therefore, the rib and transverse rebars of the conventional Y-type perfobond rib shear connectors are extremely large for the composite frames of building structures. We performed push-out tests of stubby Y-type perfobond rib shear connectors for composite frames. These shear connectors have relatively small ribs than conventional Y-type perfobond rib shear connectors. To confirm the shear resistance of these stubby shear connectors, we performed an experiment by using transverse rebars D13 and D16. The results indicate that these shear connectors have suitable shear strength and ductility for application in composite frame structures. The shear strengths obtained using D13 and D16 were not significantly different. However, the ductility of the shear connectors with D16 was 45.1% higher than that of the shear connectors with D13.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Public health suffers from noxious gas of beached Sargassum algae. Floating barrages containing them at sea will be useful provided efficiently catch them and resist to hydrodynamic pressure. Nowadays design and installation of algae barrages are empiric. Structural break, anchor and mooring chain drifts can arise. We provide a mechanical model to evaluate stresses and loads on a structure made of nets and moorings. Hydrodynamic uncertainties occur through catches, fouling, and a range of sea currents appearing in lagoons or sheltered bays. We consider a nonlinear finite-element model of elastic membrane in large displacements and small strains. We study some forcings fixed a priori on a standard section of barrage. A section 50 m long, 1 m high, with two net-faces is examined at low and moderate current velocities, 0.05 and 0.35 m.s-1, while assuming specific vertical and horizontal catch pressures. A barrage installed in lagoon at Le François on Martinique Island and being observable by satellite imagery could benefit of the computed net and mooring tensions.

Modelling errors, robust stabilization/tracking problems under parameter and model uncertainties complicate the control of the flexible underactuated systems. Chattering-free sliding-mode based input-output control law realizes robustness against the structured and unstructured uncertainties in the system dynamics and avoids excitation of unmodeled dynamics. The main purpose is to propose a robust adaptive solution for stabilizing and tracking direct-drive (DD) flexible robot arms under parameter and model uncertainties, as well as external disturbances. A lightweight robot arm subject to external and internal dynamic effects was taken into consideration. The challenges are compensating actuator dynamics with the inverter switching effects and torque ripples, stabilizing the zero dynamics under parameter/model uncertainties and disturbances while precisely track the predefined reference position. The precise control of this kind of system demands an accurate system model and knowledge of all sources that excite unmodeled dynamics. For this purpose, equations of motion for a flexible robot arm were derived and formulated for the large motion via Lagrange’s method. The goals were determined to achieve high-speed, precise position control, and satisfied accuracy by compensating the unwanted torque ripple and friction that degrades performance through an adaptive robust control approach. The actuator dynamics and their effect on the torque output were investigated due to the transmitted torque to the load side. The high-performance goals, precision&robustness issues, and stability concerns were satisfied by using robust-adaptive input-output linearization-based control law combining chattering-free sliding mode control (SMC) while avoiding the excitation of unmodeled dynamics.

Population is the main driver of land systems and environmental change. However, the population is usually treated as a variable that only considers the population number, and the multidimensional population structure is largely ignored. There has been a systematic transition of population structure in the past several decades, such as the changing household structure, the increasing aging population and divorce rate, and human migration. All these have direct or indirect impacts on land use and environmental issues. Here, we will take China as an example to examine the relationship between household dynamics and land use change in China by exam-ining changes in household structure and land use change in China between 1980 and 2020. The results show:1) the number of households increased by 130.95% from 1980 to 2020, while the population only increased by 42.83%. The size of households decreased from 4.41 to 2.92 in China from 1982 to 2020. The household dynamics vary from province to province, which is affected by urbanization rate and economic development. 2) Birth rates, divorce rates, population aging, and migration all affect household structure, which directly or indirectly affects changes in land use systems. 3) The changes in China's land use are interlinked and interact with changes in household structure, evident in the increase in residential land use and the abandonment of arable land. The rising household number increased the area of urban and rural settlement, leading to the fragmentation of cultivated land and the reduction of ecological land. To regulate land use change for sustainable development, future land use planning should take into effect of household dynamics, and reduce the negative effects of household dynamics on land systems and environmental change.

The modern material design aims to achieve multifunctionality by integrating structures in a diverse range, resulting in simple materials with embedded functions. Biological materials and organisms are typical examples of this concept, where complex functionalities are achieved through a limited material base. This review highlights the inspiration from multifunctional organisms and materials in nature, emphasizing their structural and functional integration. In particular, we discuss complex hierarchical architectures ranging from the nanoscale to the macroscale, to achieve multifunctional properties such as extreme pressure, impact and wear resistance, shape memory and self-healing, adhesiveness and anti-fouling, sensing-actuating and sensing-camouflage, and extreme environmental survival. These strategies of integrating structure and function are critical for promoting innovations and breakthroughs in the modern engineering materials and applications.

Most non-infectious diseases are associated with dysfunction of proteins or protein complexes. Аssociation between sequence and structure is analyzed since a long time, and analysis of sequence organization in domains and motifs is actual research area. A mathematical method is proposed here to identify the hierarchical organization of protein sequences. The method is based on pentapeptide as a unit of protein sequences. This method was applied on a non-homologous dataset of protein sequences. The analysis revealed 11 hierarchical levels of protein sequence organization, showing the relationship of these multiple fragments of sequences. Using different examples, we illustrated how the fragments of the spatial structure of protein correspond to the elements of the hierarchical structure of the protein sequence. A hierarchical structure is observed in the protein sequence. This methodology is an interesting basis for mathematically based classification of elements of spatial organization of proteins. Elements of the hierarchical structure of different levels of the hierarchy can be used for biotechnological and medical problems.

Recent advancements in experimental and computational methods for RNA secondary structure detection have revealed the crucial role of RNA structural elements in diverse molecular processes within living cells. It has been demonstrated that the secondary structure of the entire viral genome is often responsible for performing crucial functions in the viral life cycle and also influences virus evolution. To investigate the role of viral RNA secondary structure, alongside experimental techniques, the use of bioinformatics tools is important for analyzing various secondary structure patterns, including hairpin loops, internal loops, multifurcations, external loops, bulges, stems, and pseudoknots. Here, we have introduced a Python package for analyzing RNA secondary structure elements in viral genomes, which includes the recognition of common secondary structure patterns, the generation of descriptive statistics for these structural elements, and the provision of their basic properties. We applied the developed package to analyze the secondary structures of complete viral genomes collected from the literature, aiming to gain insights into viral function and evolution. Both the package and the collection of secondary structures of viral genomes are available at http://github.com/KazanovLab/RNAsselem.

A new Pd(II) complex of the previously reported ligand N,N′-bis[(2,2′-dihydroxybiphen-3-yl)methyl]-N,N′-dimethylethylenediamine (L) was obtained from a DMF/H2O mixture. It differs from a Pd(II) complex of L previously obtained by sole DMF. The roles in the solid state assembly of solvent molecules and molecular conformation (driven by specific transition metal ions) were studied by comparing six complexes of L containing different metal centers (Ni(II), Cd(II), Cu(II), Pd(II)). Hirshfeld surface analysis, 2D fingerprint plots and energy frameworks calculations were used to investigate the intermolecular interactions within the crystal packing of the six complexes. As suggested by interaction energies, Pd(II) and Ni(II) complexes arrange to form ribbons, while Cd(II) and Cu(II) complexes form 3D networks. Interactions between complexes and solvent molecules in the previous Pd(II) complex are replaced by complex-complex interactions in the new Pd(II) complex, while BuOH and MeOH are interchangeable in the interactions within the crystal packing of the two Ni(II) complexes. Finally, solvent molecules are not involved in the crystal packing of the Cu(II) complex. The present study suggested that the solid state assembly of these systems is mainly driven by the molecular conformation, that depends in turn by the metal ion involved, while the solvent only plays a minor role.

Abstract Big datasets are becoming increasingly common and can be challenging to understand and apply in public health. One method for lowering the dimensionality of these datasets and improving interpretability while minimizing information loss is data reduction using principal component analysis (PCA). It achieves this by successively maximizing variance through the creation of new, uncorrelated variables. PCA is an adaptive data analysis technique because it simplifies the process of finding new variables, or principal components, by solving an eigenvalue or eigenvector problem. These new variables are determined by the dataset being used, rather than by the analyst starting from scratch. It is also adaptable in another way because varieties of the method have been designed to adjust to various data structures and types. However, there are serious problems in the theoretical understanding and practical application of PCA in public health researchers, whereas its application is becoming popular in developing countries. Therefore, this article, which concentrated on using PCA to reduce data, began by outlining the fundamental concepts of PCA and going over what it can and cannot do, as well as when and how to use it. We also discussed the fundamental assumptions, benefits, and drawbacks of PCA. Furthermore, this article demonstrated and resolved PCA practical application problems in public health that most scholars are unaware of, such as variable preparation, variable inclusion and exclusion criteria for PCA, iteration steps, wealth index analysis, interpretation, and ranking.

The tension cable-supported power transmission structure (TC-PTS) is a new type of power transmission structure suitable for mountainous terrain, which is sensitive to wind load. In this regard, a nonlinear finite element analysis model of wind-induced vibration is proposed for the TC-PTS, and the wind-induced vibration response of the structure is analyzed. Firstly, the tangent stiffness matrix of the three-dimensional truss element for the supporting suspension cable and transmission line, considering the geometric nonlinearity of structures, is derived through the relationship between the element elastic energy and its displacement. Subsequently, the element mass matrix and damping matrix of the supporting suspension cable and transmission line, as well as the element nodal load vector obtained from wind load equivalence are given. Then, based on the nonlinear finite element theory, the nonlinear dynamic equation of wind-induced vibration is established for the TC-PTS and solved by Newmark-β method combined with Newton-Raphson iterative method. Furthermore, the rain-flow counting method and Miner's linear fatigue cumulative damage theory were used for wind induced fatigue damage assessment. Finally, a two-span TC-PTS is selected as an example, and the wind-induced nonlinear vibration and fatigue damage assessment are analyzed through the proposed model. The results show that the proposed model has high computational accuracy and efficiency. With the increase of wind speed and wind direction angle, the maximum lateral displacement and tension of the supporting suspension cable and transmission line increase, and their degree of increase shows a nonlinear trend. In terms of the wind-induced fatigue analysis results of TC-PTS, the fatigue damage at the end of the supporting-conductor suspension cable is greater than the fatigue damage at its midpoint. Compared to the fatigue damage at the midpoint of the conductor, the fatigue damage at the end of the conductor is less affected by wind direction angle, and both are more significantly affected by the wind speed.

In vitro fertilization (IVF) has revolutionized the field of assisted reproductive technologies (ART) by offering hope to individuals and couples struggling with infertility. Nevertheless, traditional IVF methods are not exempt from drawbacks, such as suboptimal success rates, intrusive procedures, and ethical considerations. The introduction of micro/nanorobotics in IVF offers a revolutionary chance to tackle these difficulties. This paper presents a short review of the utilization of micro/nanorobotics in IVF, investigating progress in the manipulation of sperm, retrieval of oocytes, culture of embryos, and potential future developments in this fast progressing area. In this discussion, we explore the fundamental concepts, advantages, difficulties, and possible influence of micro/nanorobotics in transforming IVF processes and enhancing patient outcomes.

Engineering Education needs to be approached in different, innovative ways to meet the needs of society, learners, and education providers. This ranges from new educational programs and innovative pedagogies in individual classrooms, to online and immersive learning, to micro-credentials and modularity along with how to enable rapid adaptation for reskilling and upskilling, to entirely new pathways of restructuring education. Gamification is the application of game elements and digital game design techniques to non-game problems, such as learning challenges. It is about using game-based mechanics, aesthetics, and game thinking to enhance users’ engagement, motivate action, and support learning. At first view, the concept of gamification does not contain game design elements, but with the addition of additional elements such as the video game component that is applied in different contexts, the users are encouraged to participate in learning activities and complete learning challenges successfully. The first step in the process of designing a gamification activity is to think like a game designer. According to Cook (2013), any process can be gamified when the following requirements are covered: (i) the gamified activity is easy to learn, (ii) user progress can be measured, (iii) continuous feedback is provided to users.

Objective To observe the effect of roxadustat on blood pressure and micro-inflammatory response in patients with hemodialysis anemia, and to provide a viable technique for the treatment of hemodialysis anemia patients. Methods A total of 100 hemodialysis anemia patients admitted to the Nephrology Department of our hospital from July 2020 to July 2021 were enrolled and randomly divided into an observation group (roxadustat) and a control group (human recombinant erythropoietin (rhEPO). The clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure were recorded and compared. Results There was no significant difference in baseline data and serum indicators (P>0.05). The study group demonstrated superior performance to the control group in terms of clinical efficacy, blood lipid metabolism, inflammatory factor levels, iron metabolism-related indicators, blood biochemical indicators, anemia indicators, adverse reactions and blood pressure (all P<0.05). Conclusion Compared with rhEPO treatment, roxadustat exhibits a promising outcome in treating anemia and has slight impact on blood pressure of patients.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

This manuscript presents a study on the spatial relationships between bike accidents, the built environment, land use, and transportation network characteristics in Budapest, Hungary using Geographic Weighted Regression (GWR). The sample period included bike crash data between 2017 and 2022. The findings provide insights into the spatial distribution of bike crashes and their severity, which can be useful for designing targeted interventions to improve bike safety in Budapest and be useful for policymakers and city planners in developing effective strategies to reduce the severity of bike crashes in urban areas. The study reveals that the built environment features, such as traffic signals, road crossings, and bus stops, are positively correlated with the bike crashes index, particularly in the inner areas of the city. However, traffic signals have a negative correlation with the bike crash index in the suburbs, where they may contribute to making roads safer for cyclists. The study also shows that commercial activity and PT stops have a higher impact on bike crashes in the northern and western districts. The GWR analysis further suggests that one-way roads and higher speed limits are associated with more severe bike crashes, while green and recreational areas are generally safer for cyclists. Future research should be focused on the traffic volume and bikes trips’ effects on the severity index.

About 90% of the Ataulfo mango (Mangifera indica L.) crops in Mexico are in the south of the country. This variety has significant amounts of antioxidant compounds. All the trees come from a small group of parents, however, the possible intravarietal variations and the micro-environments where it is grown can influence the compounds that contribute to the antioxidant capacity. The objective of this study was to quantify the antioxidant compounds of Ataulfo mango fruits of trees grown in Soconusco, Chiapas, Mexico (origin denomination), as well as fruits of the parent trees. In addition, possible associations between the contents of these compounds and the micro-environmental conditions collected were sought. In total, 465 fruits from 155 trees planted in 13 municipalities (locations) were analyzed. Fruits were collected at physiological maturity and stored at 25 °C until reaching commercial maturity. The contents of total phenolic compounds (TPC), antioxidant capacity (AC by DPPH, ABTS and FRAP methods), total anthocyanins (TA) and ascorbic acid (AA) were determined. The fruits from Huehuetán, presented the highest contents of PC (0.89 mg GAE g-1); however, the highest AC was found in the fruits harvested in Frontera Hidalgo, with 128.29 µmol TE g-1 (ABTS). The fruits obtained from the parents are within the average range of total TPC and AC, without significant differences between their fruits and those cultivated. The micro-environments where the Ataulfo mango trees are grown do not have a significant effect on antioxidant compounds (TPC, AC, TA and AA) and the only variables that allow segregation by localities are relative humidity, environmental temperature and altitude.

Severe respiratory syncytial virus (RSV) infections in early life have been linked to the development of chronic airway disease. RSV is a potent inducer of reactive oxygen species (ROS) which contributes to inflammation and enhanced clinical disease. NF-E2-related factor 2 (Nrf2) is an evolutionary conserved redox-responsive protein that helps to protect cells and whole organisms from oxidative stress and injury. The role of Nrf2 in the context of viral-mediated chronic lung injury is not known. Herein, we show that RSV experimental infection of adult Nrf2 deficient BALB/c mice (Nrf2-/-; Nrf2 KO) is characterized by enhanced disease, increased inflammatory cell recruitment to the bronchoalveolar compartment, and a more robust upregulation of innate and inflammatory genes and proteins, compared to wild type Nrf2+/+ competent mice (WT). These events that occur at very early time points, lead to increased peak RSV replication in Nrf2 KO compared to WT mice (day 5). To evaluate longitudinal changes of the lung architecture, mice were scanned weekly by high-resolution micro-computed tomography (micro-CT) imaging up to 28 days after initial viral inoculation. Based on micro-CT qualitative 2D imaging and quantitative reconstructed histogram-based analysis of lung volume and density, we found that RSV infected Nrf2 KO mice developed significantly greater and prolonged fibrosis compared to WT mice. Results of this study underscore the critical role of Nrf2-mediated protection from oxidative injury not only in acute pathogenesis of RSV infection, but also in its long-term consequences of chronic airway injury.

GaN-based micro-size light-emitting diodes (µLEDs) have a number of appealing and distinctive benefits for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, less self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is the serious barrier for applications of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as well as the optimization techniques for improving the EQE of µLEDs.

Controlled deposition of CoCrFeNiMo0.2 high entropy alloy (HEA) micro-particles was achieved using laser induced forward transfer (LIFT). Ultra-short laser pulses, 230 fs of 515 nm wavelength, were tightly focused into ∼ 2.4 μm focal spots on the ∼50 nm thick plasma-sputtered films of CoCrFeNiMo0.2. The HTA films were transferred onto glass substrates by magnetron sputtering in vacuum (10−8 atm) from the thermal spray coated substrates. The absorption coefficient of CoCrFeNiMo0.2 α ≈ 6 × 105 cm−1 was determined at 600 nm wavelength. The real and imaginary parts of refractive index (n + iκ) of HEA were determined from reflectance and transmittance using nano-films.

Around 14% of the global population does not have access to electricity. About 95% of those are living in rural Sub-Saharan Africa. Often in these regions, diesel generators are the only source of electricity. The operating cost of these diesel generators is high. However, solar and wind energy are available in most of African countries. This study presents the analysis of designing an off-grid hybrid system with a wind turbine, PV, diesel generator, and battery to power a hospital, school, and 200 household village in four locations across Somalia. The research investigated the availability of wind-solar resources in selected locations. Designing of the system and economic-technical calculations were performed using HOMER. The selection of the optimum design was based on the Cost of Electricity and Net Present Cost. The results show that for Kabaal and Ceel Buur, a WT-PV-DG-Battery is the optimal system as the wind resource in these regions is high. For Saakov and Baki, a PV-DG-Battery system proves to be optimum as the wind resource is limited here. The study also evaluated the control strategy and proved that combined dispatch was the most cost-effective for these locations. The study concluded that hybrid systems are more economical than diesel systems.

Two types of trenches cross-section in conventional vertical and brand new reverse-V-shape have fabricated on SCD substrate by micro-jet water-assist laser, the epitaxial lateral overgrowth technique has applied by microwave plasma chemical vapor deposition system in forming multiple micrometer-size channels. Raman and SEM techniques have applied in analyze both types growth layer characterization. Optical microscope has used to test microchannels hollowness. As a result, with the brand new reverse-V-shape trench, epitaxial lateral overgrowth layer reaches higher SCD surface morphology and crystal quality.

This study deals with vibrational and crystallographic aspects of the thermally induced transformation of serpentine-like garnierite into quartz, forsterite, and enstatite occurring at about 620 °C. Powder specimens of garnierite have been annealed in static air between room temperature and 1000 °C. The resulting products from the transformations detected based on thermogravimetric and differential thermal analysis, have been extensively characterized via microRaman spectroscopy, and X-ray diffraction. Our study shows that serpentine-like garnierite consists of a mixture of different mineral species. Furthermore, these garnierites and their composition can provide details based on the mineralogy and the crystalline phases resulting from the thermal treatment.

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dual-channel equalization, both based on high-Q integrated ring resonators. The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies. They operate via TE/TM mode birefringence in the resonator. We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

This paper presents a novel micro-segmented genetic algorithm (μsGA) to identify the best solution for the locomotion of a quadruped robot designed on a rectangular ABS plastic platform. We compare our algorithm with three similar algorithms found in the specialized literature: a standard genetic algorithm (GA), a micro-genetic algorithm (μGA), and a micro artificial immune system (μAIS). The quadruped robot prototype guarantees the same conditions for each test. The platform was developed using 3D printing for the structure and can accommodate the mechanisms, sensors, servomechanisms as actuators. It also has an internal battery and a multicore embedded system (mES) to process and control the robot locomotion. This research proposes a μsGA that segments the individual into specific bytes. μGA techniques are applied to each segment to reduce the processing time; the same benefits as the GA are obtained, while the use of a computer and the high computational resources characteristic of the GA are avoided. This is the reason why some research in robot locomotion is limited to simulation. The results show that the performance of μsGA is better than the three other algorithms (GA, μGA and AIS). The processing time was reduced using a mES architecture that enables parallel processing, meaning that the requirements for resources and memory were reduced. This research solves the problem of continuous locomotion of a quadruped robot, and gives a feasible solution with real performance parameters using a μsGA bio-micro algorithm and a mES architecture.

In-situ nanoindentation experiment has been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiment in characterizing nonlinear material properties of 3D integrated microelectronic devices with through-silicon-vias (TSVs). The elastic, plastic, and interfacial fracture behavior of the copper via and matrix-via interface have been characterized using small scale specimens prepared with focused-ion-beam (FIB) and nanoindentation experiment. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7 to 83.7 degrees. The mixed-mode fracture strengths were extracted using the linear elastic fracture mechanics (LEFM) analysis and a fracture criterion was obtained by fitting the extracted data with the power-law function. The vectorial interfacial strength and toughness were found to be independent with mode-mix.

Micro Injection molding combined with the use of removable inserts is one of the most promising manufacturing process for microfluidic devices, such as Lab-on-a-chip, that have the potential to revolutionize the healthcare and diagnosis system. In this work we have designed, fabricated and tested a compact and disposable plastic optical stretcher. To produce the mould inserts, two micro manufacturing technologies have been used. Micro Electro Discharge machining was used to reproduce the inverse of the capillary tube connection characterized by high aspect ratio. Thanks to the high accuracy of femtosecond laser machining, instead, we manufactured insert with perfectly aligned microfluidic channels and fiber slots, facilitating the final composition of the optical manipulation device. The optical stretcher operation is tested using microbeads and red blood cells solutions. The prototype presented in this work demonstrates the feasibility of this approach that should guarantee a real mass production of ready-to-use- Lab-on-a-chip.

In the paper, the effect of voltage increasing (from 500 VDC up to 650 VDC) on the structure and chemical composition of porous coating on titanium made by Plasma Electrolytic Oxidation, is presented. In the present paper, phosphates based coatings enriched with calcium, magnesium, zinc and copper in electrolyte based on 1 L of 85% concentrated H3PO4 with additions of Ca(NO3)2·4H2O, and Mg(NO3)2∙6H2O, and Zn(NO3)2∙6H2O, and Cu(NO3)2∙3H2O, are described. The morphology, chemical and phase composition, are evaluated using SEM, EDS, XRD, XPS, GDOES. Based on all the analyses, it was found out that the PEO coatings are porous and enriched with calcium, magnesium, zinc and copper. They consist mainly of the amorphous phase, which is more visible for higher voltages, and it is correlated with the increasing of the total PEO coating thickness (the higher the voltage, the thicker the PEO coating). However, for 650 VDC an amorphous phase and titanium substrate was also recorded with a signal from Ti2P2O7 crystalline, that was not observed for lower voltages. It was also found out that all the obtained coatings may be divided in three sub-layers, i.e. porous, semiporous, and transition one.

Various natural disasters such as floods, fires, earthquakes, etc. have affected human life. Detection and classification of large and small earthquakes caused by natural or abnormal events have been always important to Earth scientist. One of the most important research challenges in this field is the lack of an effective method for identifying and categorizing various types of seismic events at less important and important levels. Based on latest achievements of Data Mining international institutions such as Rexer-KDnugget-Gartner and also newest authentic articles, SVM, KNN, C4.5, MLP are from most important and popular and leading classifiers in data world.Therefor in present study, a boost learning system consisting support vector machine algorithms with linear regression, MLP Neural Network ، C4.5 decision tree and KNN near neighborhood have been utilized in a combined form to detect and categorize micro seismic events. In general, the steps involved in the proposed method are: 1) performing artificial seismic tests, 2) data gathering and analysis, 3) conducting preprocessing and separating training and testing samples, 4) generating relevant models with training samples and detecting and categorizing test samples and 5) extracting a cluster with the maximum candidate using boost learning. After simulations, it was observed that the accuracy of proposed boost method to the best answer was about 6.1% higher compare to other methods and the error rate was 0.082% of recalling. Accuracy of detection and classification to the best answer were also improved compare to other methods up to 2.31% and 6.34%, respectively.

Stenting is an alternative to endarterectomy for the treatment of carotid artery stenosis. However, stenting is associated with a higher risk of procedural stroke secondary to distal thromboembolism. Hybrid stents with a micromesh layer have been proposed to address this complication. We developed a micropatterned thin film nitinol (M-TFN) covered stent designed to prevent thromboembolism during carotid intervention. This innovation may obviate the need or work synergistically with embolic protection devices. The proposed double layered stent is low-profile, thromboresistant, and covered with a M-TFN that can be fabricated with fenestrations of varying geometries and sizes. The M-TFN was created in multiple geometries, dimensions, and porosities by sputter deposition. The efficiency of various M-TFN to capture embolic particles was evaluated in different atherosclerotic carotid stenotic conditions through in vitro tests. The covered stent prevented emboli dislodgement in the range of 70-96% during 30min duration tests. In vitro vascular cell growth study results showed that endothelial cell elongation, alignment and growth behaviour silhouettes significantly enhance specifically on the diamond-shape M-TFN with the dimensions of 145µm×20µm and a porosity of 32%. Future studies will require in-vivo testing. Our results demonstrate that M-TFN has a promising potential for carotid artery stenting.

The crystal structure of Pb₁₀(PO₄)₆O, the proposed matrix for the potential room-temperature superconductor LK-99, Pb_10-xCu_x(PO₄)₆O (x = 0.9-1.0), has been reinvestigated by single-crystal X-ray diffraction using crystals prepared by Merker and Wondratschek (The crystal structure is trigonal, P, a = 9.8109(6), c = 14.8403(12) Å, V = 1237.06(15), R₁ = 0.0413 using 3456 unique observed reflections. The crystal structure of Pb₁₀(PO₄)₆O is a superstructure with regard to the ‘standard’ P6₃/m apatite structure type. The doubling of the c parameter is induced by the ordering of ‘additional’ O’ atoms within the structure channels running parallel to the c axis and centered at (00z). The O’ atoms form short bonds to the Pb1 atoms, resulting in splitting the Pb1 site into two, Pb1A and Pb1B. The structural distortions are further transmitted to the Pb phosphate framework formed by four Pb2 sites and PO₄ groups. The structure data previously reported by Krivovichev and Burns (Z. Kristallogr. 2003, 218, 357-365) may either correspond to the Pb₁₀(PO₄)₆O_x(OH)_2-x (x ~ 0.4) member of the Pb₁₀(PO₄)₆O - Pb₁₀(PO₄)₆(OH)₂ solid solution series, or to the high-temperature polymorph of Pb₁₀(PO₄)₆O (with the phase with doubled c parameter being the low-temperature polymorph).

Nickel nitrate diammine, Ni(NH₃)₂(NO₃)₂, can be synthesised from the thermal decomposition of the nickel nitrate hexammine, Ni[(NH₃)₆](NO₃)₂. The hexammine decomposes in 2 distinct steps; the first releases 4 equivalents of ammonia while the second involves the release of NO_x, N₂ and H₂O to yield NiO. The intermediate diammine compound can be isolated following the first deammoniation step or synthesised as a single phase from the hexammine under vacuum. Powder X-ray diffraction (PXD) experiments have allowed the structure of Ni(NH₃)₂(NO₃)₂ to be solved for the first time. The compound crystallises in orthorhombic space group Pca2₁ (a = 11.0628 (5) Å, b = 6.0454 (3) Å, c = 9.3526 (4) Å; Z = 4) and contains 11 non-hydrogen atoms in the asymmetric unit. Fourier Transform Infrared (FTIR) spectroscopy demonstrates that the bonding in the ammine is consistent with the structure determined by PXD.

A monocular vision pose estimation and identification algorithm used on a small spacecraft for future orbital servicing is studied in this paper. A tracker spacecraft equipped with a short-range vision system is proposed to recover the 3D structural model of a space target in orbit and automatically identify its solar panels and main body using only visual information from an onboard camera. The proposed reconstruction and identification framework is tested using structure-from-motion and point cloud identification methods. The Efficient Perspective-n-Points (EPnP) descriptor is used for pose estimation. Triangulated points are used for component segmentation by means of orientation histogram descriptors. Experimental results based on laboratory images of a spacecraft model show the effectiveness and robustness of our approach.

In this article we review the advances that have been made on the understanding of the high-pressure structural, vibrational, and electronic properties of wolframite-type oxides since the first works in the early 1990s. Mainly tungstates, which are the best known wolframites, but also tantalates and niobates, with an isomorphic ambient-pressure wolframite structure, have been included in this review. Apart from estimating the bulk moduli of all known wolframites; the cation-oxygen bond distances and their change with pressure have been correlated with their compressibility. The composition variations of all wolframites have been employed to understand their different structural phase transitions to post-wolframite structures as a response to high pressure. The number of Raman modes and band gap energy changes have been also analyzed in the basis of these compositional differences. The reviewed results are relevant for both fundamental science and for the development of wolframites as scintillating detectors. The possible next research venues of wolframites have also been evaluated.

Scope, time, and cost permanently effects each other and most of Information Technology projects fails due to these three factors. Scope shifting mostly occur due to time and cost. At project start, lack of understanding of project and product scope is focal involvement that leads to unsuccessful projects. Complete software scope definition determines quality of project. Defining the customer requirement and the definite scope of project has key role for implementation of project management. The complications originates when systems are developed from impractical expectations and misunderstanding requirements. These problems are cause of many changes, occurs in system development and leads to poor scope management. Scope creep is one of the momentous prompting parameter on the success of project. The failure in manage scope creep leads for 80 percent of software projects failure. However, using agile approach the impact of scope creep on projects become insignificant. A correctly distinct scope tends us to develop a quality product, within identified plans and decided cost to the stake-holders.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

Cross-border e-commerce is an opportunity for micro, small and medium sized enterprise (MSMEs) in developing countries. Based on a resource-based approach, this research studied how to support resource lacking enterprises with export marketing strategy. It dealt with actual business cases of Mongolian entrepreneurs trying to export Mongolian products to Korean market. Multiple source data including interviews, internal documents, and group discussions, were matched with theories to come up with strategies and validated by supporting organizations in Mongolia and Korea. The research suggests that MSMEs should rely on third party digital platforms rather than setting up their own. For product strtategy of the marketing mix, sellecting competitive product categories and supporting them adjusting to foreign markets and quality assurance is needed. For price strategy, loccally high priced products should use a price penetration strategy with a lower price compared to competing foreign products. For place strategy, supporting organizations should partner with exporters for collective delivery. For promotion strategy, they need to support the capacity of MSMEs enabling them to use digital marketing tools effectivly. These strategies were validated and adopted by supporting organizations in Monglia and Korea.

The IgM and IgT classes were previously identified and characterized in the Antarctic teleost Trematomus bernacchii, a species belonging to the Perciform suborder Notothenoidei. Herein we characterized the gene encoding the polymeric immunoglobulin receptor (pIgR) in the same species and compared it to pIgR of multiple teleost species belonging to five perciform sub-orders, including 11 Antarctic and one non-Antarctic (Cottoperca gobio) notothenioid species, the latter living in less cold periantarctic sea. Antarctic pIgR genes displayed particularly long in-trons marked by sites of transposable elements and transcription factors. Furthermore, analysis of T. bernacchii pIgR cDNA unveiled multiple amino acid substitutions unique to Antarctic species, all introducing adaptive features, including N-glycosylation sequons. Interestingly, C. gobio shared most features with the other perciforms rather than with the cold adapted relatives. T. bernacchii pIgR transcripts were predominantly expressed in mucosal tissues, as indicated by q-PCR and in situ hybridization analysis. These results suggest that in cold adapted species pIgR preserved its fundamental role in mucosal immune defense, although remarkable gene structure modifications occurred.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, the molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopores imbibition during shut-in for a typical shale reservoir Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between “interfacial water molecules” at the imbibition front and “adsorbed oil molecules” on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil especially the heavy hydrocarbon component in the adsorbed layer tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore's wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for “interfacial water molecules” to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect of pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for EOR.

To achieve a micro-destructive and rapid measurement of the wood density of standing trees, this study investigated the feasibility of using the micro-drilling resistance method, formulated a mathematical model, explored the potential for a unified model across multiple tree species, and analyzed the influence of moisture content on measurement accuracy. First, 231 tree cores and drill resistance data were sampled from Pinus massoniana, Cunninghamia lanceolate, and Cryptomeria fortunei. The basic density and moisture content of each core were measured, and the average value of each resistance data record was calculated. Second, the average drill resistance, the natural logarithm of average drill resistance, and absolute moisture content were used as independent variables, while the wood basic density was used as the dependent variable. Third, the total model of the three tree species and sub-model for each tree species were established through a stepwise regression method. Finally, the accuracy of each model was compared and analyzed with that of using the average basic density of each tree species as an estimated density. The results revealed that the estimation accuracy of the sub-model for each tree species was 1.670 percentage points higher than the average value of each tree species used as the density estimation value for these tree species. Additionally, except for Cryptomeria fortunei, the natural logarithm of drill resistance significantly influenced the wood density model at a significance level of 0.05. Moreover, moisture content significantly affected the total model and sub-models of Pinus massoniana at a significance level of 0.05. The estimation accuracy of the total mathematical model was 2.125 percentage points lower than that achieved using the average basic density of each tree species to predict their density. The results indicated the feasibility of using the micro-drilling resistance method to measure the wood density of standing trees. Moreover, the relationship between wood density and drill resistance did not follow a linear pattern, and moisture content slightly influenced the drill needle resistance. Furthermore, the establishment of a mathematical model for each tree species was deemed essential. This study provides valuable guidance for measuring the wood density of standing trees through the micro-drilling resistance method.

Emerging applications of optical technologies are driving the development of miniaturised light sources, which in turn require the fabrication of matching micro-optical elements with sub-1 mm cross sections and high optical quality. This is particularly challenging for spatially-constrained biomedical applications where reduced dimensionality is required, such as endoscopy, optogenetics, or optical implants. Planarisation of a lens by the Fresnel lens approach was adapted for a conical lens (axicon) and was made by direct femtosecond 780 nm/100 fs laser writing in SZ2080™polymer with photo-initiator. Optical characterisation of the positive and negative fraxicons is presented. Numerical modeling of fraxicon optical performance under illumination by incoherent and spatially extended light sources is compared with the ideal case of plane wave illumination. Considering the potential for rapid replication in soft polymers and resists, this approach holds great promise for the most demanding technological applications.

Road traffic transportation has flourished in the process of urbanization by its advantages, but it also produces harmful environmental vibrations. The vibration problem is especially significant for production workshops with precision instruments. A field measurement was conducted to analyze the source characteristics and propagation laws of traffic-induced vibrations. Off the northern side of an urban highway lies a microelectronics workshop. When a large truck passes by, both the vibration responses on the ground and in the workshop considerably increase. Greater vibration is produced in the vertical direction than in the X and Y axes. The predominant frequency band of the vibration response caused by road traffic vehicles is lower than 20 Hz. The vertical vibration responses of the first and second floors in the workshop greatly exceed the VC-C limit because of the high daily traffic flow. Attribute to the excitation of the operation of the manufacturing equipment on the second floor, the vertical vibration level of the second floor is essentially higher than that of the first floor. Therefore, it is impossible to disregard the micro-vibration in the workplace produced by the manufacturing machinery as well as the ex-citement of the road traffic. The measured data can be used to test potential numerical models for forecasting vibrations caused by traffic on roads as well as to guide vibration assessment work throughout the planning and design stages of roads.

The present distribution examines the effects of nozzle diameter, inlet mass rate, and channel geometry on the fuel distribution in annular combustion chambers of micro gas turbines, taking into account the importance of more uniform fuel distribution in the nozzles connected to the fuel supply channels. A comparison has been made between the numerically calculated pressure drop between the inlet and outlet of the fuel supply nozzle and the experimental value obtained. All fuel supply nozzles with a diameter of 500 micrometers are considered for the micro gas turbine. A more uniform distribution results in better combustion and higher efficiency. A geometrical change in the design of the fuel supply nozzle improved the uniformity of the flow distribution without increasing the pressure drop.

The practical necessity of strengthening of reinforced concrete structure elements requires a choice of a method which would provide cost-effectiveness, simplicity of construction and durability of the chosen solution. One of the ways is strengthening using the material belonging to the group of micro-reinforced concretes called ferrocement. The paper presents the comparative analysis of some of the results of RC beams exposed mainly to flexure, strengthened with ferrocement elements (strips) applied by gluing on the on the tensed side of RC beams. The results are obtained using the experimental, analytical and numerical research on the adequate models. Strengthening of the beams was performed in the form of four types of ferrocement strips (four different strip widths and four different numbers of wire mesh layers). The numerical non-linear analysis using finite elements method (FEM) was employed, with the introduction of the corresponding characteristics of constitutive material obtained by the experiments on the test specimens. The analytical researches were performed using known analytical calculation methods in order to formulate the model for the calculation of the ultimate and serviceability limit states of the strengthened cross-section. The results presented in the paper, through their comparative compatibility, confirmed the applicability of this strengthening method.

In the field of clinical medicine, the real-time monitoring of carbon dioxide gas exhaled by the human body is of great significance. At present, the detection devices in the market are mainly detected by sucking a small amount of gas in the nasal cavity to the detection device, and there are some problems such as too long sampling tubes, easy blockage or distortion, and abnormal gas dispersion. In this paper, a micro-nano optical fiber sensor that can directly detect the concentration of end-tidal carbon dioxide is proposed. The measurement is achieved by using the principle of high evanescent field absorption, and the operating band is 2.004 μm. The sensor uses micro-nano optical fiber as the sensing area, and then detects the presence of carbon dioxide gas exhaled by human body through optical power attenuation. The function of micro-nano fiber is to realize the transmission of signal light and also serve as the absorption medium of the gas to be measured. In addition, the variation of light power also reflects the respiratory cycle of the human body. The sensor can realize rapid real-time response to carbon dioxide gas detection, with small size, low cost, and easy to replace. It has great application potential in clinical scenarios such as Gastrointestinal Endoscopes that require real-time monitoring of human respiration.

This paper presents a novel dynamic camera parameter control method for position and posture estimation of highly miniaturized AR markers (micro AR markers) using a low cost general camera. The proposed method performs iterative calculation of the marker’s position and posture to converge them to specified accuracy with dynamically updating the camera’s zoom, focus and other parameter values based on the detected marker’s depth distances. For a 10 mm square micro AR marker, the proposed system demonstrated recognition accuracy of better than ±1.0% for depth distance and 2.5∘ for posture angle with a maximum recognition range of 1.0 m. In addition, the iterative calculation time was at most 0.7 seconds in an initial detection of the marker. These experimental results suggest that the proposed method and system can be applied to a robotic precise handling of small objects with low cost.

The genus Eucalyptus is a globally captivated source of hardwood and is well known for its medicinal uses. The hybrid and wild species of Eucalyptus are widely used as exotic plantations due to their renowned potential of adapting to various systems and sites, furthermore, making the species the most extensively propagated. Despite unquestionable progression in biotechnological and tissue culture approaches, the productivity of plantations is still limited often due to the low efficiency of clonal propagation from cuttings. The obtained F1 hybrids yield high biomass and High-quality low-cost raw material for large-scale production, however, the development of hybrid, clonal multiplication, proliferation, and post-developmental studies are still major concerns. This riveting review describes the problems concerned with in-vitro and clonal propagation of Eucalypt plantation; recent advances in biotechnological and tissue culture practices for massive and rapid micro-propagation of Eucalyptus; as well, highlights the Eucalypt germplasm preservation techniques.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

The purpose of this review is to present the current role of ultrasound-based techniques in the diagnostic pathway of prostate cancer (PCa). With overdiagnosis and overtreatment of a clinically insignificant PCa over the past years, multiparametric magnetic resonance imaging (mpMRI) became recommended for every patient suspected of PCa before performing a biopsy. It enabled targeted sampling of the suspicious prostate regions, improving the accuracy of the traditional systematic biopsy. However, mpMRI is associated with high costs, relatively low availability, long and separate procedure or exposure to the contrast agent. The novel ultrasound modalities such as shear wave elastography (SWE), contrast-enhanced ultrasound (CEUS) or high frequency micro-ultrasound (MicroUS) may be capable of maintaining the performance of mpMRI without its limitations. Moreover, the real-time lesion visualization during biopsy would significantly simplify the diagnostic process. Another value of these new techniques is the ability to enhance the performance of mpMRI by creating the image fusion of multiple modalities. Such models might be further analyzed by artificial intelligence to mark the regions of interest for investigators and help to decide about the biopsy indications. The dynamic development and promising results of new ultrasound-based techniques should encourage researchers to thoroughly study their utilization in prostate imaging.

Parts of shotgun cartridges are a significant source of plastic litter in the marine environment. Empty cartridge shells may not be picked up by the hunter who fired them, and plastic wads that serve to separate the propellant from the shot load, are lost down-range when a shot is fired. Such litter items constitute a cosmetic and aesthetic problem on coastlines and may cause harm to marine animals and in the later stages of decomposition break down into harmful micro plastic particles. There exists no reliable estimate of the global exposure of marine ecosystems to this plastic source. However, in some countries it has been subject to closer examination, including for example, Denmark where the annual contribution of plastic wads into marine systems was estimated to 600,000 pieces (c2 tonnes), and the accumulated density of washed-up items (both wads and shells) was 3.7 items per 100 m coastline. Increasing awareness of this problem has caused scientists, hunters’ communities and governments to suggest altered practice including transition to the use of biodegradable cartridge components, first and foremost wads as this item is invariable lost during hunting. Several manufacturers provide shotgun cartridges containing biodegradable wads based on different types of materials, including fibers and various types of plastics, for example PVAL (poly(vinyl alcohol)) and PHA (polyhydroxyalkanoate). In this paper, we review the most recent literature on the amounts and related environmental hazards of plastic dispersed from hunting ammunition into marine ecosystems. We summarize the market availability of shotgun cartridges with biodegradable wads and discuss chemical, technical, economical and legal aspects of a transition to the use of such products.

ST-elevation myocardial infarction (STEMI) remains one of the leading causes of morbidity and mortality worldwide. The identification of novel metabolic and imaging biomarkers could unveil key pathophysiological mechanisms at the molecular level and promote personalized care in patients with acute coronary syndromes. We studied 38 patients with STEMI who underwent primary percutaneous coronary intervention and thrombus aspiration. We sought to correlate serum ceramide levels with micro-CT quantified aspirated thrombus volume and relevant angiographic outcomes, including modified TIMI thrombus grade and pre- or post-procedural TIMI flow. Higher ceramide C16:0 levels were significantly, but weakly correlated with larger aspirated thrombus volume (Spearman r=0.326, p=0.046), larger intracoronary thrombus burden (Nagelkerke R2=0.236, p=0.030) and worse pre- and post-procedural TIMI flow (Nagelkerke R2=0.210; p=0.049 and Nagelkerke R2=0.277; p=0.039, respectively). Ceramides C24:0 and C24:1 were also significantly associated with larger intracoronary thrombus burden (Nagelkerke R2=0.311; p=0.008 and Nagelkerke R2=0.423; p=0.001, respectively). In conclusion, serum ceramide levels (mainly C16:0 and C24:1) were higher among patients with larger intracoronary and aspirated thrombus burden. This suggests that quantification of serum ceramides might improve risk-stratification of patients with STEMI and facilitate a more individualized approach in everyday clinical practice.

Individual plant cells are the building blocks for all plantae and artificially constructed plant biomaterials, like biocomposites. Secondary cell walls (SCWs) are a key component for mediating mechanical strength and stiffness in both living vascular plants and biocomposite materials. In this paper, we study the structure and biomechanics of cultured plant cells during the cellular developmental stages associated with SCW formation. We use a model culture system that induces transdifferentiation of Arabidopsis thaliana cells to xylem vessel elements, upon treatment with dexamethasone (DEX). We group the transdifferentiation process into three distinct stages, based on morphological observations of the cell walls. The first stage includes cells with only a primary cell wall (PCW), the second covers cells that have formed a SCW, and the third stage includes cells with a ruptured tonoplast and partially or fully degraded PCW. We adopt a multi-scale approach to study the mechanical properties of cells in these three stages. We perform large-scale indentations with a micro-compression system and nanoscale indentations through atomic force microscopy (AFM), in three different osmotic conditions. We introduce a spring-based model to deconvolve the competing stiffness contributions from turgor pressure, PCW, SCW and cytoplasm in the stiffness of differentiating cells. Prior to triggering differentiation, cells in hypotonic pressure conditions are significantly stiffer than cells in isotonic or hypertonic conditions, highlighting the dominant role of turgor pressure. Plasmolyzed cells with a SCW reach similar levels of stiffness as cells with maximum turgor pressure. The stiffness of the PCW in all of these conditions is lower than the stiffness of the fully-formed SCW. Our results provide the first experimental characterization of the mechanics of SCW formation at single cell level.

Sulphuric acid is a widely used raw material in the chemical industry. Its corrosive effect on materials varies considerably, depending on impurities, temperature and water content. Accordingly, good corrosion resistance under all conditions is very difficult to achieve. This is especially an issue for micro process apparatus with very thin walls. Furthermore, such devices are often joint by diffusion bonding what may alter materials properties due to high temperatures and long dwell times. In fact, for each new material, the diffusion bonding parameters must be optimized and the impact on mechanical as well as corrosion properties must be investigated. In this paper, two high molybdenum alloys, namely Hastelloy B3 and BC-1, were evaluated. Diffusion bonding tests were performed using ten layers of sheet material in between round stock. Corrosion tests were performed in 70 % sulphuric acid at 100°C for 1000 h. Tensile tests on both alloys were carried out for different material conditions, to determine the change in mechanical strength and elongation at fracture values. In general, independent of the condition of the materials, the fracture behavior of both alloys was found to be ductile and the specimens show the typical dimple structure, in the case of diffusion bonded samples, interrupted by weak spots or rather non-bonded areas. These areas are obviously causing the onset of material failure and thus, a degradation of mechanical properties. Tensile samples, that were aged in 70% sulphuric acid at 100°C for 1000 hours showed local corrosion attacks at the grain boundaries at the circumferential surfaces and especially at the joining planes – for Hastelloy B3 much more pronounced than for Hastelloy BC-1. Accordingly, a further decrease of both, the stress- and elongation at fracture values is observed. However, the typical material parameters like 0.2 % yield strength used for dimensioning components are found to be sufficient high, even when operating the materials under such harsh conditions. When concluding the results, at least Hastelloy BC-1 reveals both sufficient good mechanical properties and an excellent corrosion resistance, regardless of the heat treatment, and could be considered for manufacturing micro-process engineering apparatuses operated in a sulphuric acid environment. This is a significant advance compared to the results obtained within a AiF project, previously carried out on four different materials to investigate the corrosion resistance in sulphuric acid.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Direct laser writing based on non-linear 3D nanolithography (also known as 3D laser lithography, 3DLL) is a powerful technology to manufacture polymeric micro-optical components. However, practical applications of these elements are limited due to the lack of knowledge of their optical resilience and durability. In this work, we employ 3DLL for the fabrication of bulk (i.e. fully filled) and woodpile structures out of different photopolymers. We then characterize them using S-on-1 laser induced damage threshold (LIDT) measurements. In this way, quantitative data of LIDT values can be collected. Furthermore, this method permits to gather damage morphologies. The results presented in this work demonstrate that LIDT values depend on the material and the geometry of the structure. Bulk non-photosensitized hybrid organic-inorganic photopolymer SZ2080 structures are found to be the most resilient with a damage threshold being of 169±15 mJ/cm².

Continuous in-home monitoring of older adults living alone aims to improve their quality of life and independence, by detecting early signs of illness and functional decline or emergency conditions. To meet requirements for technology acceptance by seniors (unobtrusiveness, non-intrusiveness, privacy-preservation), this study presents and discusses a new smart sensor system for the detection of abnormalities during daily activities, based on ultra-wideband radar providing rich, not privacy-sensitive, information useful for sensing both cardiorespiratory and body movements, regardless of ambient lighting conditions and physical obstructions (through-wall sensing). The radar sensing is a very promising technology, enabling the measurement of vital signs and body movements at a distance, and thus meeting both requirements of unobtrusiveness and accuracy. In particular, impulse-radio ultra-wideband radar has attracted considerable attention in recent years thanks to many properties that make it useful for assisted living purposes. The proposed sensing system, evaluated in meaningful assisted living scenarios by involving 30 participants, exhibited the ability to detect vital signs, to discriminate among dangerous situations and activities of daily living, and to accommodate individual physical characteristics and habits. The reported results show that vital signs can be detected also while carrying out daily activities or after a fall event (post-fall phase), with accuracy varying according to the level of movements, reaching up to 95% and 91% in detecting respiration and heart rates, respectively. Similarly, good results were achieved in fall detection by using the micro-motion signature and unsupervised learning, with sensitivity and specificity greater than 97% and 90%, respectively.

A conventional electrical grid mostly depends on the electrical power generated from fossil fuels. However, the pollutants from fossil fuels are the key factors for adverse climate change. Most of the developed countries of the world have already recognized the fact that the energy mix requires to be diversified by incorporating renewable energy. This is especially relevant for many of the member countries of the Organization of Islamic Cooperation (OIC), consisting of 57 countries, whose abundance of fossil fuel reserve indicates that much of their electric power is still generated from fossil fuels. In order to integrate renewable energy sources into the hybrid energy mix, an existing conventional grid needs to undergo drastic changes. Alongside this, the population boom in the OIC member countries has caused higher demand for a steady supply of electricity that the conventional grids have long been struggling to cope with. With a view to solving this multifaceted problem, incorporation of the smart power management schemes is indispensable using a smart electrical grid, where information and communications technology is integrated into its major building blocks. This allows advanced applications of a grid, such as the formation of micro-grids, demand-side management, energy storage, high-tech power electronic converters, etc. As the smart grids are being adopted by many developed countries, it is high time for the OIC member countries to pay due attention to this development, if they have not already done so. This paper explains, with special focus on the OIC member countries, the various smart power management technologies, their operations and applications, and the benefits and challenges. Then it goes on to carry out the Strength-Weakness-Opportunity-Threat with Analytical-Heuristic-Procedure (SWOT-AHP) analysis to evaluate its feasibility of incorporation and the underlying strategies appropriate for its implementation. Furthermore, a Hybrid Multi-Criteria-Decision-Making (MCDM) analysis is performed to evaluate the sequence of the emphasis that should be given on each of the technologies from those available for the smart power management initiative. Finally, the study reinforces the stance by drawing parallels from the UN Sustainable Development Goals (SDG) and highlights the importance of the smart grid in line with the global vision of SDG. This paper aims at assisting the decision-makers in implementing smart power management schemes in the OIC member countries, in particular, and other countries of the world, in general.

That form and function relates, is the maxim to anatomy and physiology. Yet form-function relations can be difficult to establish. Human subjects with excessive trabeculated myocardium in the left ventricle, for example, are diagnosed with non-compaction cardiomyopathy, but the extent of trabeculations may be without relation to ejection fraction. Rather than rejecting a relation between form and function, we may ask whether the salient function is assessed; is there a relation to electrical propagation, mean arterial blood pressure, propensity to form blood clots, or all? And how should extent of trabeculated muscle be assessed? While reviewing literature on trabeculated muscle, we applied Tinbergen’s four types of causation - how does it work, why does it work, how is it made, and why did it evolve - to better parse what is meant by form and function. The paper is structured around cases that highlight advantages and pitfalls of applying Tinbergen’s questions. It further uses the evolution of lunglessness in amphibians to argue lung reduction can impact on chamber septation, and it considers the evolution of an arterial outflow in fishes to argue that reductions in energy consumption may drive structural changes with little consequences to function. Concerning trabeculations, we argue they relate to pump function in the embryo in the couple of weeks before the onset of coronary circulation. In fetal and postnatal stages, a spectrum of trabeculated-to-compact myocardium makes no difference to cardiac function and in this period form and function may appear unrelated.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

Most fully developed galaxies have vivid spiral structure, but the formation and evolution of spiral structure is still a mystery that is not fully understood in astrophysics. We find that the currently used equations of galactic dynamics contain some unreasonable components. In this paper, the following three working assumptions are introduced to simplify the galactic structural equations. 1. In the research of large-scale structure, the retarded potential of the gravitational field should be taken into account. The propagating time of the gravitational field from center to border is longer than the revolution periods of the stars near the center of galaxy. Newton's gravitational potential is unreasonable for such case, and the weak field and low velocity approximation of Einstein's field equation should be adopted. 2. The stars in a fully developed galaxy should be zero-pressure and inviscid fluid, and the equation of motion is different from that of ordinary continuum mechanics. Stars move along geodesics. 3. The structure of the galaxy is only related to the total mass density distribution. The equation of state of dark halo is different from that of ordinary luminous interstellar matter, so their trajectories are also very different. Dark halo and ordinary matter in galaxy are automatically separated. The total mass density distribution can be presupposed according to the observation data, and then it can be determined by comparing the solution of the equations with the observed data. These assumptions and treatments are supported by theory and observation. The variables of the equations of simplified galactic dynamics are separated from each other, and the equations are well-posed and can be solved according to a definite procedure. Therefore, this simplified dynamic equation system provides a more reasonable and practical framework for the further study of galactic structure, and can solve many practical problems. Besides, it is closely related to the study of dark energy and dark matter.

In this work, a series of compounds in the CaO-½Er2O3-CoOz ternary oxide system were synthesized in air at 885℃ using high temperature solid-phase synthesis method. Phase boundary of each solid solution region in the CaO-½Er2O3-CoOz system was determined by X-ray powder diffraction technique. The phase diagram of the CaO-½Er2O3-CoOz system at 885℃ includes three series of ternary oxide solid solutions : (Ca3-xErx)Co4O9-z (0≤x≤0.9), (Ca3-xErx)Co2O6-z (0≤x≤1.25) and (Er1-xCax)CoO3-z (0≤x≤0.33). Four three-phase regions and five solid solution tie-line regions were obtained. The structure of perovskite solid solution (Ca3-xErx)Co2O6-z has been analyzed by Rietveld refinements. With the increase of Er content, the cell parameters of (Ca3-xErx)Co2O6-z exhibit an decreasing trend in a and b directions and an increasing trend in c direction.

Soil-transmitted helminthiasis (STH), a neglected tropical disease (NTD) remains a major health problem all over the world including Ghana, which has STH prevalence of 25.4%. To control the disease, the government of Ghana currently concentrates on implementing mass drug administration (MDA) efforts focusing only among school-aged children. However, various studies have suggested that focusing on only a specific group for MDA may not be cost-effective. Moreover, some adults such as teachers and school-workers spend large fraction of their time with children, who shed more parasite in environment due to unhygienic behavior, and thus have a higher risk of getting infected as compared to other adults. In this study we use a mathematical model to evaluate age-structured and risk-based policies for implementing MDA while capturing transmission dynamics of STH in Ghana. A cost model was developed that included various costs related to MDA to study cost-effectiveness of current policies of MDA in Ghana against novel policies to control STH in Ghana. We carry out analysis for five different scenarios— I: no MDA (baseline), II: current MDA policy (focusing children) in Ghana, III: MDA for different age groups (adults and children groups) for unlimited budget, IV: MDA for different age groups with limitations of number of individuals treated, and, V: MDA for different groups based on their risk of getting infected (adults school workers (high-risk group), adults non-school workers and children groups). Our results suggest that it might be more cost-effective to allocate treatment through MDA to at least some proportion of adults along with children. In case of unlimited budget, the best strategy in Scenario IV would be to treat approximately 22% of adults and approximately 45% of children. The most cost-effective among the 5 scenarios is suggested through scenario V, where high-risk adults group and children are provided MDA at higher level than low-risk adults. In conclusion, age-structured and risk-based allocation of treatment and resources is crucial to reducing STH load in developing countries.

In recent decades, perovskite-type compounds (ABB′O3) have been exhaustively studied due to their unique ferroelectric properties. In this work, a systematic study aiming to prepare fine particles in the binary system SrZrO₃–SrTiO₃ was conducted under hydrothermal conditions in a KOH (5 M) solution at 200 °C for 4 h under a constant stirring speed of 130 rpm. The precursors employed were SrSO₄ powder (&lt; 38 μm size) and coprecipitated hydrous gels of Zr(OH)₄•9.64 H₂O (Zr-gel) and Ti(OH)₄•4.5H₂O (Ti-gel), which were mixed according to the stoichiometry of the SrZr_1-xTixO₃ in the compositional range of 0.0&gt;x&gt;100.0 mol% Ti⁴⁺. The XRD results revealed the formation of two crystalline phases rich in Zr⁴⁺, an orthorhombic structured SrZr0.93Ti0.07O3 and a cubic structured SrZr0.75Ti0.25O3 within the compositional range of 0.1–0.5 mol of Ti4+. A cubic perovskite-structured solid solution, SrTi1-xZrxO3, was preferentially formed within the compositional range of 0.5&gt;x&gt;0.1 mol% Ti⁴⁺. The SrZrO₃ and SrZr_0.93Ti_0.07O₃-rich phases had particle sizes averaging 3 m with a cubic morphology. However, a remarkable reduction in the particle size occurred on solid solutions prepared with hydrous Ti-gel over contents of 15 mol% Ti⁴⁺ in the reaction media, resulting in the formation of nanosized particles agglomerates with cuboidal shape self-assembled via a 3D hierarchical architecture, the sizes of these particles varied in the range between 141.0–175.5 nm. The limited coarsening of the particles is discussed based on the Zr-gel and Ti-gel dehydration capability differences that occurred under hydrothermal processing.

Alunogen, Al2(SO4)3·17H2O, occurs as an efflorescent in acid mine drainage, low-temperature fumarolic or pseudofumarolic (at coal fires) terrestrial environments. It is considered as one of the main Al-sulfates of Martian soils demanding comprehensive crystal chemical data of natural terrestrial samples. However, structural studies of natural alunogen were carried out in 1970s without localization of H atoms and have not previously been performed for samples from geothermal fields, despite the fact that these environments are considered as proxies of the Martian conditions. The studied alunogen sample comes from Verkhne-Koshelevsky geothermal field (Koshelev volcano, Kamchatka, Russia). Its chemical formula is somewhat dehydrated, Al2(SO4)3×15.8 H2O. The crystal structure was solved and refined to R1 = 0.068 based on 5112 unique observed reflections with I > 2σ(I). Alunogen crystalizes in P-1 space group, a = 7.4194(3), b = 26.9763(9), c = 6.0549(2) Å, α = 90.043(3), β = 97.703(3), γ = 91.673(3) °, V = 1200.41(7) Å3, Z = 2. The crystal structure consists of isolated SO4 tetrahedra, Al(H2O)6 octahedra and H2O molecules connected by hydrogen bonds. The structure refinement includes Al, S and O positions that are similar to previous structure determinations and thirty-four H positions localized for the natural sample first. The study also shows the absence of isomorphic substitutions in the composition of alunogen despite the iron-enriched environment of mineral crystallization. The variability of the alunogen crystal structure is reflected in the number of “zeolite” H2O molecules and their splitting. The structure complexity of alunogen and its modifications ranges from 333-346 bits/cell for models with non-localized H atoms to 783-828 bits/cell for models with localized H atoms. The higher values correspond to higher hydration state of alunogen.

Utilization of Bidirectional Reflectance Distribution Function (BRDF) model parameters obtained from the multi-angular remote sensing is one of the approaches for the retrieval of vegetation structural information. In this research, the potential of multi-angular vegetation indices, formulated by the combination of multi-spectral reflectance from different view angles, for the retrieval of forest above ground biomass was assessed. This research was implemented in the New England region with the availability of a high quality forest inventory database. The multi-angular vegetation indices were generated by the simulation of the Moderate Resolution Imaging Spectroradiometer (MODIS) BRDF/Albedo Model Parameters Product (MCD43A1 Version 6) based BRDF parameters. The effects of seasonal (spring, summer, autumn, and winter) composites of the multi-angular vegetation indices on above ground biomass, angular relationship of the spectral reflectance with above ground biomass, and the interrelationships between the multi-angular vegetation indices were analyzed. Among the existing multi-angular vegetation indices, only the Nadir BRDF-adjusted NDVI ( and Hot-spot incorporated NDVI ( showed significant relationship (more than 50%) with the above ground biomass. This research proposed two more sensitive vegetation structural indices, Fore-scattering Back-scattering NDVI and Vegetation Structure Index (VSI). The Fore-scattering Back-scattering NDVI showed higher sensitivity (R² = 0.62, RMSE = 52.46) towards the above ground biomass than existing multi-angular vegetation indices. Furthermore, the VSI performed in the most efficient way explaining 64% variation of the above ground biomass, suggesting that the right choice of the spectral channel and observation geometry should be considered for improving the estimates of the above ground biomass. In addition, the right choice of seasonal data (summer) was found to be important for estimating the forest biomass while other seasonal data were either insensitive or pointless. The promising results shown by the VSI suggest that it could be an appropriate candidate for monitoring vegetation structure from the multi-angular satellite remote sensing.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

The severe and complex COVID-19 symptoms, often needing hospital care, occur suddenly, late in the virus replication stage of SARS-CoV-2 infection. Hospitalised patients have tissue damage due to micro-clots at multiple sites. Could long-covid, also clinically variable, be a milder form caused by “nano-clots”, too small to cause detectable tissue damage? The timing and suddenness of the onset of serious disease needs an explanation. A paper reported on the first 20 children needing urgent hospital care. No child had any symptoms prior to suddenly becoming seriously ill, only one had a positive PCR test but all had positive SARS-CoV-2 antibody test. That finding indicated to me that this onset occurred at the moment of sero-conversion. An emerging viral moiety, the virion-IgG-antibody complex, has concentrations rapidly increasing, then decreasing. It is known that influenza-IgG-antibody-complex consists of many virions bound together by the antibody. It seems a reasonable step to propose that SARS-2, being a large virus and having many spike proteins, can form larger clumps of virus-IgG-antibody complexes than with influenza, the former being sufficiently large to initiate micro-clots. Therefore, my hypotheses is that the SARS-CoV-2 virion-antibody complex initiates micro-clot formation. Either before or after sero-conversion, the complex will be at too low a concentration to initiate micro-clots. To be useful, a hypothesis should be testable, provide explanations and give predictions. My presentation will give examples. I like the way that several apparently separate pieces of a jig-saw puzzle have come together to form a single picture. [I suggest that the reader scrolls down to the addenda [10,11 & 12] before reading the ICAR Poster]

The spatial segregation is a characteristic of Latin American cities, resulting in distinct dynamics of social inclusion and exclusion at both spatial and identity levels. Then, specific green spaces may convert into appreciated and contested territories, where various actors negotiate their uses and regulations. Considering a case-study in a green icon of the metropolitan city of Santiago de Chile, the main objective of the present study was to describe and comprehend the uses and meanings of the Quebrada Macul park among different social groups over the past two decades. We employed qualitative methods including six in-depth interviews with key informants (social and ecological leaders, historical neighbors, and park workers), five participant observations in the park, and statistical analysis of visitors. Results reveal that (1) the transition of being a popularly used hill to a metropolitan park rises tensions between public and private statuses of place; (2) conflicts emerge regarding who uses the space and how, reflecting power dynamics among different social groups; (3) the park, beyond being a public space, holds significant identity value for its historical residents, both for those who fought for its recovery and those who have lived closely, so processes of forgetfulness might be resentful. We conclude on enduring meanings of the park associated with the struggle for the place among different groups, highlighting the role of memory for the social integration of groups among natural spaces.

The ceramic sherds from approximately 20 samples of lead-glazed tableware, recovered from diverse archaeological sites, including three repurposed storage pits transformed into dumpsters within the medieval city of Santarém (13th-14th century), underwent a meticulous examination. This investigation utilized techniques such as micro-Raman, ground state diffuse reflectance absorption, and X-ray fluorescence spectroscopies, in addition to X-ray diffraction and stereomicroscopy. A parallel study was conducted on contemporaneous European ceramics (glazed sherds) sourced from archaeological sites dating back to the 13th-15th centuries in Saintonge (France), Ardenne, Zomergem, and Bruges (Belgium), as well as Surrey-Hampshire, Kingston, and Cheam (England). The colour of the ceramic bodies is predominantly white or whitish, with a few exhibiting a vivid red hue. Ceramic sherds with a light paste composition were likely crafted using kaolin clays as raw materials. Analyses of fabric, mineralogical, and elemental composition of the sherds suggest that the majority of Santarém's glazed ceramics were locally or regionally produced, potentially derived from a Pliocene kaolin-rich sand formation. However, this conclusion is not supported by the absence of discovered lead glaze kilns or workshops in Santarém for the late Middle Ages. A distinctive feature from the European workshop ceramics lies in the quartz temper content and fabric.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

The 1060 aluminium alloy is widely applied to electronic industry, construction area, aerospace field, traffic engineering, decoration and consumption goods market for its good chemical, physical and mechanical properties. In general, excellent processing property is necessary and important for manufacturing of complicated panels. In this paper, a special 2D ultrasonic vibration incremental forming method is designed to improve its plasticity and mechanical properties. Three kind of processing methods including traditional single point incremental forming, longitudinal ultrasonic vibration incremental forming and 2D ultrasonic vibration incremental forming are conducted for flexible manufacture of conical parts of 1060 aluminium alloy sheet. Then micro-hardness tests, residual stress tests and scanning electron microscopy tests are carried out to probe its revolution of micro-structure and mechanical properties and to analysis the effects of different types of ultrasonic vibration on plasticity and fracture characteristic of 1060 aluminium alloy. It is proved that 2D ultrasonic vibration is facilitated to improvement of plasticity and surface qualities of 1060 aluminium alloy than the other two processing methods. So, the novel 2D ultrasonic vibration incremental forming possesses substantial application values on flexible and rapid manufacturing of complicated thin-walled component of aluminium alloy.

The ceramic pastes of ca. 31 samples recovered from the Almaraz archaeological site, located in the south bench of Tagus River, were studied in detail using XRF, micro-Raman and GSDR spectroscopies, as well as the XRD technique. The ceramic sherds could be grouped into six categories, Red Slip tableware, Decorated tableware, Yellow Slip tableware, Grey tableware, Common tableware and Handmade pottery. Our studies of the mineralogic composition of the sherds` body indicate that all ceramics were produced locally, using silicious clays in most cases and calcareous clays in a few ones. Micro-Raman and ground state diffuse reflectance absorption spectroscopy provided useful information regarding the materials used to produce the coloured ceramics: hematite and brookite for the red slip and decorated ceramics, jacobsite or carbon black for the black decoration or grey ceramics. For the yellow slip tableware a simple engobe rich in yellow clay was used. XRF spectroscopic studies provided the elemental composition of all samples, and biplots of the Potassium (K) versus Calcium (Ca) contents, normalized to the silicon content of each ceramic paste, clearly show that Pliocene and Miocene local clays sources were used to produce most ceramics. Only one sherd can be considered a Lisbon production.

Micro-plastics (MPs) become significantly important to society since their commercial manufacture began in the 1950s because of their low production costs, stability, light weight, and adaptability. Plastic was produced in 400 million tons worldwide in 2020, compared to 1.5 million tons just 60 years earlier. Scientists predict that by 2050, plastic production would increase to 33 billion tons. MPs are a rising scientific and societal issue in the environment as a new type of contaminant that is widely disseminated in aquatic ecosystems and organisms. Aquatic species that come into contact with MPs for an extended period of time experience ecotoxicity, which includes oxidative stress, genotoxicity, neurotoxicity, and reproductive issues. In aquatic environments, MPs not only transport chemicals within animals but also serve as mediators for chemicals or other contaminants. As a result of co-exposure of MPs and chemical contaminants, various toxicity incidences involving aquatic organisms have been reported. The final exposure of MPs occurs in humans through biomagnification of aquatic edible products. This study presents an important overview of the literature on MP ingestion by aquatic biota. It covers topics such as the present scenario of plastic pollution worldwide, the pathways that MPs take to reach humans and aquatic species, the eco-toxicological impacts of MPs on aquatic species, the relation between MPs and other environmental pollution and the ensuing effects on aquatic organisms, and the MP pollution status in Bangladesh.

Castanea sativa Mill., an indigenous species of the mountainous Gabala region of Azerbaijan, where its local variety is now facing the danger of extinction. The preservation of this variety of European chestnut requires the development of effective strategies for reliable in vitro regeneration systems as an alternative to traditional methods, which has become the main objective of this study. In solving this problem, the generally accepted technique of micro-multiplication of axillary shoots was mainly used. First, a phased sterilization of was carried out using liquid soap, Previkur fungicide and mercury (II) chloride. DKW (Driver and Kuniyuki Walnut) nutrient medium was used for germination of explants, into which growth stimulants BAP (Benzilamunapurine), IBA (Indole - 3 butyric acid), IAA (Indole Acetic acid), NAA (Naphthalene Acetic Acid) and GA3 (Gibberelic acid) were introduced in various combinations and quantities. The test of the above-mentioned sterilization model revealed significant shortcomings in terms of the acceptability of the results obtained (16-77%). It was also found that the germination of explants takes 14 days and it is better to conduct it in a DKW environment containing hormones BAP (0.6 mg), IBA (0.1 mg) and GA3 (0.1 mg) / 1 L DKW. A mixture of BAP (0.1mg) + IBA (0.35 mg) is more suitable for the reproduction of grown explants + GA3 (0.2 mg) / 1 l DKW (the result is 3 new micro-plants for each explant), and for good root formation (it takes 30 days) – a mixture of IBA 1.0 mg + NAA 0.5 mg + IAA 0.5 mg / l L DKW. After the shoots have acquired a certain length (at least 1.5 cm), it is required to transfer them for 22 days to a DKW medium containing IBA (1 mg), IAA (0.5 mg) and NAA(0.5 mg) / l L DKW so that the root splitting process begins and ends.

To prevent CO2 leakage and ensure the safety of long-term CO2 storage, it is essential to investigate the flow mechanism of CO2 in complex pore structures at the pore scale. This study focuses on reviewing the experimental, theoretical, and numerical simulation studies on the microscopic flow of CO2 in complex pore structures during the last decade. For example, advanced imaging techniques, such as X-ray computed tomography (CT) and nuclear magnetic resonance (NMR), are used to reconstruct the complex pore structures of rocks. Mathematical methods, such as Darcy's law, Young–Laplace’s law, and the Navier-Stokes equation, are used to describe the microscopic flow of CO2. Numerical methods, such as the lattice Boltzmann method (LBM) and pore network (PN) model, are used for numerical simulation. The application of these experimental and theoretical models and numerical simulation studies is discussed, considering the effect of complex pore structures. Finally, future research is suggested to focus on: (1) Conducting real-time CT scanning experiments of CO2 displacement combined with the developed real-time CT scanning clamping device to realize real-time visualization and provide quantitative description of the flow behavior of CO2 in complex pore structures; (2) The effect of pore structures change on the CO2 flow mechanism caused by the chemical reaction between CO2 and the pore surface, the flow theory of CO2 considering wettability and damage theory in a complex pore structures; (3) The flow mechanism of multi-phase CO2 in complex pore structures; (4) The flow mechanism of CO2 in the pore structures at multiscale and the scale upgrade from microscopic to mesoscopic to macroscopic. Generally, this study focuses on reviewing the research progress of CO2 flow mechanisms in complex pore structures at the pore scale and affords an overview of potential advanced developments to enhance the current understanding of CO2 microscopic flow mechanisms.

This paper deals with the quantitative analysis of measured fracture-induced electromagnetic radiation (FEMR) in the vicinity of the Dead Sea Transform using the Angel-M1 instrument, which enables the recording of FEMR signals in a 3D manner. Results show both the possibility of estimating the sizes of micro-fractures that are the sources of the radiation, and of assessing the direction of their location to the measuring device and the range of magnitude Mw of the impending "events" (EQ's) associated with the present FEMR measurements. Moreover, the relation between the measured FEMR activity (the number of FEMR hits per unit time) and the FEMR event magnitudes shows consistency with the Gutenberg-Richter relationship for the region. Such measurements could therefore constitute a preliminary 'field reinforcement' towards an EMR valid method for a real earthquake forecast, which would provide much earlier warnings than the seismic ones. Obviously, the present observed FEMR measurements can only be used as an assessment of the stress concentration and micro-fracturing in the region since they relate to the very initial nucleation phase of a "virtual" (extremely low Richter scale value) earthquake, but they do provide the necessary feasibility test for a prediction method since all lab-measured FEMR features were confirmed also in the field.

The device and method in accordance with the constant pressure regulation of micro droplet PCR in microfluidic chips are developed to explore the optimization way for the micro droplet movement, fragmentation, and bubble generation in microfluidic chips in existing digital PCR technology. In the developed device, an air source device is adopted to regulate the pressure in the chip, such that micro droplet generation and PCR amplification without bubbles can be achieved. In 3 min, the sample in 20ul will be distributed into nearly 50,000 water-in-oil droplets exhibiting a diameter of about 87μm, and the micro droplet will be subjected to a close arrangement in the chip without air bubbles. The device and chip are adopted to quantitatively detect the human gene . As indicated by the experimental results, a good linear relationship exists between detection signal and DNA concentration ranging from 101~ 105 copies /μL (R2=0.999). The micro droplet PCR devices based on constant pressure regulation chips exhibit a wide variety of advantages (e.g., achieving high pollution resistance, micro droplet fragmentation and integration avoidance, reducing human interference, and standardizing results). Thus, micro droplet PCR devices based on constant pressure regulation chips have promising applications in nucleic acid quantification.

Artificial intelligence, a key technological tool in the era of the 4th Industrial Revolution, is being actively applied to education beyond industry, economy, and culture. In the future society, understanding and using artificial intelligence technology will be considered an essential skill for everyone, and the professionalism of AI education for pre-service teachers nurturing future talents is also important. This study verifies the effectiveness of pre-service teachers after undergoing a 15-week extension program consisting of AI Literacy Education (10 weeks), AI-Linked Subjet Education (3 weeks), and Micro-teaching (2 weeks) which was designed to enhance the AI ​​education professionalism of pre-service teachers. The AI Literacy Education section consisted of understanding AI, AI ethics, and basic programming, and the education was conducted through both experience and practice. After that, the pre-service teachers analyzed the curriculum of the 5th and 6th grades of an elementary school, and developed a subject-related education program using AI tools in three stages. Using the developed program, micro-teaching classes were conducted twice. The study results are as follows. First, there was a change in the positive perception of AI (p<.05). Second, the understanding of AI educational technology tools was improved and the recognition of the usefulness of developing a curriculum-related program was expanded. Third, the importance of teacher competency development was learned through the micro-teaching, and the students' understanding of the learning process was expanded.

This study examines the negative impacts of dark stores on the urban environment from three perspectives: land use, transportation, and streetscape. It is conducted on B-Mart, a representative dark store in South Korea. First, in terms of land use, we find that dark stores that function as logistics facilities conflict with the surrounding land use. Second, by analyzing the location of dark stores and the hourly traffic volume of delivery vehicles, we find that the impact on the surrounding transportation infrastructure and pedestrian traffic is not as significant as previously claimed. However, during the transportation and loading process of the dark store, several problems such as traffic violations, illegal parking, and illegal loading were observed, posing a risk to nearby vehicles and pedestrians. Third, in terms of streetscapes, the location of dark stores on the ground floor of buildings can harm streetscapes. The current urban planning system in South Korea does not clearly define the status and function of dark stores, making it unclear how to manage them. Therefore, it is necessary to clarify their legal definition and introduce urban planning and design guidelines that are consistent with their appropriate location and appearance.

Calibration of flow devices is important in several areas of pharmaceutical, flow chemistry and microfluidic applications where dosage of process liquids or accurate measurement of the flow rate is important. The process-oriented liquid itself might influence the performance of the flow device and the simultaneous determination of the dynamic viscosity under flow conditions might be a valuable information for the process parameters. To offer the simultaneous calibration of the dynamic viscosity of the process-oriented liquid at the corresponding flowrate, METAS has built a pipe viscometer for the traceable in-line measurement of the dynamic viscosity in the current flow facilities for low flow rates from 1 L/min to 150 mL/min and pressure drops up to 10 bar. The traceability of all the measuring quantities as well as the geometrical dimensions of the micro tube guarantee the traceability of the pipe viscometer to SI units. The most challenging part is the traceable determination of the inner diameter of the micro tube. This can be achieved by measuring the pressure drop as a function of flow rate with the pipe viscometer and applying the law of Hagen-Poiseuille with a traceable dynamic viscosity of a reference liquid (water) or perform the measurements with the micro-CT at METAS, which determines the inner diameter by x-ray diffraction. The validation of the stated measurement uncertainty of the pipe viscometer has been performed by means of calibration of the dynamic viscosity of several reference liquids with traceable density and kinematic viscosity. The setup of the facility, the traceability as well as the uncertainty calculation of the pipe viscometer for the in-line measurement of the dynamic viscosity are discussed in this paper.

Micro-expression (ME) is one of the key psychological stress reactions. It is a modest, spontaneous facial mechanism. ME has significant applicability in a variety of psychologically-related sectors because to its precision and unpredictability with regard to psychological manifestations. Nevertheless, the current Micro-expression recognition (MER) algorithms have poor accuracy and a limited quantity of ME data, and this study issue has not been thoroughly investigated. Therefore, we present an approach for deep learning based on a Spatio-temporal capsule network (STCP-Net). STCP-Net has four components: a jitter reduction module, a differential feature extraction module, an STCP module, and a fully linked layer. The first two modules are aimed to extract diversifying differential features more precisely and to limit the influence of head jitter. The STCP module is used to extract Spatio-temporal features layer by layer, taking the temporal and geographical connection between features into account. This research runs sufficient trials using the Leave One Subject Out (LOSO) methodology for cross-validation using the CASMEII dataset. The conclusion and analysis demonstrate that the algorithm is innovative and efficient.

Cancer stem cells (CSCs) are one of the cell types that account for cancer heterogeneity. They arrest in the G0 phase and generate non-CSC progeny by self-renewing and pluripotency activity, resulting in tumor recurrence, metastasis, and chemoresistance. One CSC can stimulate tumor relapse and can re-grow a metastatic tumor. So, CSC is a promising target for eradicating tumors, and developing an anti-CSC method has become a top priority in cancer therapy. In recent years competing endogenous RNA (ceRNA) have emerged as an important class of post-transcriptional regulators that affect gene expression via competition for microRNA (miRNA) binding. Furthermore, aberrant ceRNA expression is associated with tumor progression. To overcome therapeutic resistance due to CSCs, we need to improve our existing understanding of the mechanisms by which ceRNAs are implicated in CSC-related relapse. Thus, this review was designed in order to discuss the role of ceRNAs in CSCs function. We reviewed the role of ceRNAs in acquiring CSCs characteristics in the form of different pathways including Rho GTPase/F-actin_ Yes-associated protein (YAP)/transcriptional co-activator with PDZ-binding motif (TAZ) (Hippo), Wnt/β-catenin pathway, transforming growth factor (TGF)-b–urothelial carcinoma-associated 1 (UCA1)–Slug pathway, etc. Finally, considering the comprehensive impacts of the ceRNA network on different pathways, a treatment strategy driving the ceRNA network might be effective. Targeting ceRNAs may open the path for new cancer therapeutic targets and can be used in clinical research.

This research was specifically aimed at assessing the influence of sulfur in triple-super phosphate (TSP) on wheat yield. From the results, wheat showed response to sulfur (S) from gypsum (in 67%); and nitrogen (N) from urea in about 100% (of 24 sites). Based on this N was found to be the most limiting element to wheat production followed by sulfur, and then by phosphorus. TSP is tested to contain agronomically up to 2-6% by weight of S. However, wheat didn’t show response to S impurity supplied in the form of TSP. Though, not statistically significant, it is observed that there have always been yield increments by certain percent due to S from TSP in 8 out of 10 target sites, which is depicted in the increasing trends of yield response curves. From this it is learnt that, the benefits of the accidental/incidental application of such high analysis fertilizers can be many-folds in the quality attributes of wheat, if the soils of such investigation at the same time would contain significant amount of organic matter (OM). Indeed, such analysis would be vital in varietal specific nutrient requirement studies in precision-farming and/or in categorizing soils into fertility gradients and fertilizer recommendation domains.

Conventional pervious pavement materials (PPM) consist of cement and aggregate materials and are known for poor durability due to their brittle behavior. Herein, we fabricated polymeric PPMs from durable and abundant polyurethane (PU) to enhance the durability of the material and undertook mechanical and microscopic characterizations. PU-based PPM samples with varying aggregate sizes were produced and the compressive strength and water permeability of each were examined. The pore and tortuosity characteristics of the specimens were analyzed using X-ray micro-computed tomography (micro-CT). Through the micro-CT analysis, the morphological characteristics of the internal structures of PPM were identified and the correlations between the pore size distribution, connectivity, and tortuosity within the specimen were quantitatively analyzed. The microstructures derived from micro-CT were generated as a finite element model and the stress distribution generated inside was numerically determined.

Microfluidic devices which integrate both rapid mixing and liquid jetting for sample delivery are an emerging solution for studying molecular dynamics via X-ray diffraction. Here we use finite element modelling to investigate the efficiency and time-resolution achievable using microfluidic mixers within the parameter range required for producing stable liquid jets. Three-dimensional simulations, validated by experimental data, are used to determine the velocity and concentration distribution within these devices. The results show that by adopting a serpentine geometry, it is possible to induce chaotic mixing, which effectively reduces the time required to achieve a homogeneous mixture for sample delivery. Further, we investigate the effect of flow rate and the mixer microchannel size on the mixing efficiency and minimum time required for complete mixing of the two solutions whilst maintaining a stable jet. In general, we find that the smaller the cross-sectional area of the mixer microchannel, the shorter the time needed to achieve homogeneous mixing for a given flow rate. The results of these simulations will form the basis for optimised designs enabling the study of molecular dynamics occurring on millisecond timescales using integrated mix-and-inject microfluidic devices.

We review recent work on broadband RF channelizers based on integrated optical frequency Kerr micro-combs combined with passive micro-ring resonator filters, with microcombs having channel spacings of 200GHz and 49GHz. This approach to realizing RF channelizers offers reduced complexity, size, and potential cost for a wide range of applications to microwave signal detection.

The optimization problem of two or more special-purpose functions of the energy system is subjected to an analysis. Based on experience of our research and general knowledge of partial solutions of energy system optimization at the level of control of production and power energy supply by energy companies in the Czech Republic, a special-purpose (cost) function has been defined. By analysing the special-purpose function, penalty and limitations have been defined. Using the fuzzy logic, a set of suitable solutions for the special-purpose function is accepted. An optimum of the special-purpose function is looked for using the simulated annealing method. The history of electricity consumption is sorted by day and by hour, representing the multidimensional data. When using the cluster analysis, type daytime diagrams of consumption are defined. Type daytime diagrams form prototypes of identified clusters. The so-called self-organizing neural network with Kohonen map attached is used to perform the cluster analysis. The result of our research is presented by an experiment.