When developing bone implants Young's modulus is one of the primary characteristics of the material that should be considered. The study focuses on the possibility of regulating the modulus of the alloy Ti-50.8 at % Ni by varying its initial structure as well as aging-induced microstructure in a wide range. Microstructure observations were performed using TEM and SEM observations. The calorimetric studies of martensitic transformations were carried out using "Mettler Toledo 822e". Tensile tests were performed in a test temperature range of ‒196≤T≤+100°C using an «IN-STRON 5966». The grain/subgrain size of B2-austenite strongly affects the modulus magnitude. This effect is ambiguous for a material with a grain size of 0.13–3 µm and depends on the test temperature. The effectiveness of aging on the modulus reduction depends on the initial structure: it is most pronounced in an alloy with a relatively coarse grain size of 9 µm and brings a decrease by 3.8 times at a temperature of 37°C. Bone-like elastic modulus (10–30 GPa) at a human body temperature of 37°C is realized in an aged fine-grained NiTi alloy. An ultrafine-grained sub-structure exhibits he same values of Young's modulus in the temperature range from -100°С to 25°С.

Monometallic (Ni, Co, Cu) and bimetallic (Ni-Co, Ni-Cu) 10-20 wt. % metal containing catalysts supported on fly ash zeolite were prepared by post-synthesis impregnation method. The catalysts were characterized by X-ray powder diffraction, N2 physisorption, XPS and H2-TPR methods. Finely dispersed metal oxides and mixed oxides were detected after the decomposition of impregnating salt on the relevant zeolite support. By reduction intermetallic, NiCo and NiCu phases were identified in the bimetallic catalysts. Hydrogeoxygenation of lignocellulosic biomass-derived levulinic acid to γ-valerolactone (GVL) was studied. Bimetallic, 10 wt. % Ni, 10 wt. % Cu or Co containing fly ash zeolite catalyst showed higher catalytic activity than monometallic ones. Their selectivity to GVL reached 70-85 % at 100 % conversion. The reaction proceeds through formation of 4-hydroxy pentanoic acid, as the only intermediate compound.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

Three kinds of Ni based alloy cladding coatings were prepared on 316L stainless steel at different power. The microstructure of the cladding layer was observed and analyzed by XRD, metallographic microscope and SEM. The hardness of the cladding layer was measured, and the wear resistance of the cladding layer was tested by friction instrument. The results show that the effect of laser cladding is good and the cladding layer has a good metallurgical bonding with the substrate. Different microstructures such as dendritic and equiaxed grains can be observed in the cladding layer. With the increase of laser power, more equiaxed and columnar dendrites can be observed. The phase composition of the cladding layer is mainly composed of γ - Ni solid solution and some intermetallic compounds such as Ni3B, Cr5B3 and Ni17Si3. The results of EDS show that there are some differences in the distribution of C and Si between dendrites. The hardness of the cladding layer is about 600 HV0.2, which is about three times of the substrate (~ 200 HV0.2). Through the analysis of the wear morphology, the substrate wear is serious, there are serious shedding, mainly adhesive wear and abrasive wear. However, the wear of cladding layer is slight, which is abrasive wear, and there are some grooves on the surface.

Functional dependence of the axial zero-field splitting parameter D with respect to a properly chosen geometrical parameter (Dstr) in metal complexes is termed the Magnetostructural D-Correlation. In mononuclear hexacoordinate Ni(II) complexes with the ground electronic term 3B1g (3A2g in the regular octahedron) it proceeds along two intercepting straight lines allowing to predict the sign and magnitude of the D-parameter by knowing the X-ray structure alone; Dstr is constructed from the metal-ligand bond lengths. In hexacoordinate Co(II) complexes it is applicable only in the segment of the compressed bipyramid where the ground electronic term 4B1g is orbitally non-degenerate so that the spin Hamiltonian formalism holds true. The D vs Dstr correlation is strongly non-linear and it is represented by a set of decreasing exponentials. In tetracoordinate Co(II) complexes, on the contrary, the angular distortion from the regular tetrahedron is crucial so that the appropriate structural parameter Dstr is constructed of bond angles. All of these empirical correlations originate in the electronic structure of metal complexes that can be modelled by the generalized crystal-field theory. As the barrier to spin reversal in the single-molecule magnets is proportional to the D-value, for a rational tuning and/or prediction of the single-molecule magnetic behavior knowledge/prediction of the D-parameter is beneficial. In this review, we present the statistical processing of an extensive set of structural and magnetic data of Co(II) and Ni(II) complexes, which were published over the past 15 years. Magnetostructural D-correlations defined for this data set are reviewed in detail.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Aqueous Zinc ion batteries (ZIBs) possess significant potential in large energy storage systems due to their cost-effectiveness and environmental protection. However, the limited voltage window and poor reaction kinetics of the cathode material are still bottlenecks, restricting the further development of ZIBs. In this work, we rationally design Ni-doped V2O5@3D Ni core/shell composite on carbon cloth electrode (Ni-V2O5@3D Ni@CC) by growing Ni-V2O5 on the free-standing 3D Ni metal nanonets for high-voltage and high-capacity ZIBs. Impressively, the embedded Ni doping increases the interlayer spacing of V2O5, extending the working voltage and improving the Zn2+ kinetics reaction of the cathode materials, at the same time the 3D structure with high specific surface area and superior electronic conductivity benefits to fast Zn2+ transport. Consequently, the as-designed Ni-V2O5@3D Ni@CC cathodes can operate within a wide voltage window from 0.3 to 1.8 V vs. Zn/Zn2+ and deliver a high capacity of 270 mAh g-1 at a high current density of 0.8 A g-1. In addition, the reversible Zn2+ (de)-incorporation reaction mechanisms in the Ni-V2O5@3D Ni@CC cathodes are investigated by multiple characterization methods. As a result, we achieve a big step toward the practical applications of commercial ZIBs.

A series of Ni/KIT6 catalystprecusors with 25wt.%Ni loading amount were reduced in H₂ at 400, 450, 500, and 550ºC, respectively. The studied catalysts were investigated by XRD, Quasiin-situ XPS, BET, TEM, and H₂-TPDanalysis methods.It was found that reduction temperature is an important factor affecting the hydrodeoxygenation (HDO) performance of the studied catalysts. The reduction temperature influences mainly the content of active components, crystal size, and the abilityfor adsorbing and activatingH2. The developed pore structure and large specific surface area of the KIT-6 support favored the Ni dispersion.The RT450 catalyst, which was prepared in H₂ atmosphere at 450 ºC, has the best HDO performance. Ethyl acetate can be completely transformed, and maintain 96.8% ethane selectivity and 3.2% methane selectivity at 300 ºC. The calculated apparent activation energies of the prepared catalysts increased in the following order: RT550 > RT400 > RT500 > RT450.

In this paper, various Ni-P composite coatings containing toner, MoS2, and nano-SiO2 particles were deposited on steel substrates by the electroless method. Then, the electrochemical properties of these coatings after a heat treatment process were compared. The microstructural evaluations were also done by using the optical and electron microscopy methods. Both Tafel polarization and electrochemical impedance spectroscopy techniques were utilized to survey the electrochemical behavior of such coatings. The surface morphology of all coatings contained cauliflower-like nodules. The X-ray diffraction patterns showed the crystalline phases of Ni and Ni3P for all coatings after the heat-treatment step. Obtained results showed that all composite coatings exhibited lower corrosion rates with respect to Ni-P coatings. Such a reduction was about 21.6-92.2%. This behavior was attributed to the presence of reinforcement as barriers for corrosive ion diffusion through the coating plus the changes in detected phases and thickness. Electrochemical impedance spectroscopy test results also demonstrated that the increase in the polarization resistance for composites coatings was about 18.4-85.3% after 1 h immersion in a 0.6M NaCl solution; however, when the immersion time increased to 24 h, such increased resistance changed to 18.1 to 73.1%. Totally, despite the lower deposition rate, the presence of MoS2 and nano-SiO2 particles were more effective than toner particles to raise the corrosion rate of the Ni-P coating.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

The effect of current density of electrodeposition on the morphology, hardness, and corrosion resistance of the Ni coatings and Ni-Al2O3 coatings on Q345 steels were investigated. The surface of Ni coatings exhibited the cellular structure, while the surface of Ni-Al2O3 composite coatings showed the finer protrusions structure. The thickness of all coatings increased as the current density of electrodeposition increased from 1.5 A/dm2 to 3.0 A/dm2. After coating, the hardness and corrosion resistance of the Q345 steels were significantly enhanced. Furthermore, for the Ni coatings and Ni-Al2O3 coatings, the highest hardness and best anticorrosion property were obtained at 2.5 A/dm2 of electrodeposition current density. Compared with the Ni coatings, the co-deposition of Al2O3 nanoparticles improved the hardness of Ni-Al2O3 coating due to the second phase strengthen, but reduced the thickness and corrosion resistance due to more defects caused by the coelectrodeposition of the Al2O3 particles.

This study investigated dry reforming of methane with combined catalysts supported on γ-Al2O3 support doped with 3.0 wt. % TiO2. The physicochemical properties of all the catalysts were determined by inductively-coupled plasma/mass spectrometry metal analysis, nitrogen physisorption, X-ray diffraction, temperature programmed reduction/desorption, thermogravimetric analysis, and scanning electron microscopy. The addition of CeO2 and MgO to Ni strengthened the interaction between the Ni and the support. The catalytic activity results indicated that the CeO2 and MgO addition to Ni did not do much in retarding carbon deposition, but they improved the activity of the catalysts. Among the tested catalysts, it was found that the catalyst with the composition of 5.0 wt % NiO-10.0 wt % CeO2/3.0 wt %TiO2-γ-Al2O3 resulted in the highest CH4 and CO2 conversion with H2/CO mole ratio close to unity. The optimum reaction conditions in terms of reactant conversion and H2/CO mole ratio were achieved by varying space velocity and CO2/CH4 mole ratio.

In recent years, cerium dioxide (CeO2) has attracted considerable attention owing to its remarkable performance in various applications, including photocatalysis, fuel cells, and catalysis. This study explores the effect of nickel (Ni) doping on the structural, thermal, and chemical properties of CeO2 nanorods, particularly focusing on oxygen vacancy-related phenomena. Utilizing X-ray powder diffraction (XRD), alterations in crystal structure and peak shifts were observed, indicating successful Ni doping and the formation of Ni2O3 at higher doping levels, likely due to non-equilibrium reactions. Thermal gravimetric analysis (TGA) revealed changes in oxygen release mechanisms, with increasing Ni doping resulting in the release of lattice oxygen at lower temperatures. Raman spectroscopy corroborated these findings by identifying characteristic peaks associated with oxygen vacancies, facilitating the assessment of Ni doping levels. Overall, this study underscores the substantial impact of Ni doping on CeO2 nanorods, shedding light on tailored catalytic applications through modulation of oxygen vacancies while preserving the nanorod morphology.

Herein, we report about the monometallic Ni and bimetallic Pd-Ni catalysts supported on CeO2-Al2O3 binary oxide, which were investigated in oxy-steam reforming of methanol (OSRM). Monometallic and bimetallic supported catalysts were prepared by wet aqueous impregnation and subsequent impregnation method, respectively. The physicochemical properties of the catalytic systems were investigated using various methods such as: BET, XRD, TPR-H2, TPD-NH3, XPS and SEM-EDS techniques. It has been proven that the addition of palladium to the nickel catalyst facilitates its reduction. The activity tests performed for all catalysts confirmed the promotion effect of palladium on catalytic activity of nickel catalyst and selectivity towards hydrogen production. Both nickel and bimetallic palladium-nickel supported catalysts showed excellent stability during the reaction. Such catalytic systems are valuable for the advance of the field of fuel cell technology.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

Acetaldehyde decomposition was performed under heating at the temperature range of 25-125oC and UV irradiation on TiO2 doped by the metallic Ni powder and TiO2 supported on the nickel foam. Process was carried out in high temperature reaction chamber “The Praying MantisTM”, with simultaneous in situ FTIR measurements and UV irradiation. Ni powder was added to TiO2 in the quantity of 0.5 to 5.0 wt%. Photothermal measurements of acetaldehyde decomposition indicated, that the highest yield of acetaldehyde conversion on TiO2 und UV irradiation was obtained at 75oC. Doping of nickel to TiO2 did not increase its photocatalytic activity. Contrary to that, application of nickel foam as a support for TiO2 appeared to be highly advantageous, because increased decomposition of acetaldehyde from 31 to 52% at 25oC and then to 85% at 100oC by comparison with TiO2 itself. At the same time mineralisation of acetaldehyde to CO2 increased two times at the presence of nickel foam. However, oxidised nickel foam used as support for TiO2 was detrimental. Most likely, different mechanisms of electrons transfer between Ni-TiO2 and NiO-TiO2 occurred. Application of nickel foam greatly enhanced separation of free carriers in TiO2. As a consequence, high yields of the photocatalytic reactions were obtained.

Spectrometers have a wide range of applications ranging from optical to non-optical spectroscopy. The need for compact, portable, and user-friendly spectrometers has been the pivot of attention from small laboratories to the industrial scale. Here, the Czerny Turner configuration-based optical spectrometer simulation design is carried out using ZEMAX OpticStudio. A compact and low-cost optical spectrometer in the visible range has been developed by using diffraction grating as a dispersive element and USB-type WebCAM CCD (Charge-coupled device) as a detector instead of an expensive commercial diffraction grating and detector. Using National Instruments LabVIEW, data acquisition, processing, and displaying techniques are made possible. We have employed different virtual images in LabVIEW programs to collect the pixel-to-pixel information and wavelength-intensity information from the image captured using the WebCAM CCD. Finally, we have shown that the OpticStudio-based spectrometer and experimental measurements of the developed spectrometer are in good agreement.

In this study, Cu/Ni and Cu/Al multilayer thin films with individual layer thickness varying from 25 nm to 200 nm were deposited at room temperature and further annealed up to 300 ℃. The mechanical and microstructural properties of the multilayers were characterized by nanoindentation, x-ray diffraction, and scanning electron microscopy. Both systems exhibited an increase in hardness with increasing annealing temperature. However, the Cu/Ni system showed a gradual and moderate (up to 30%) hardness increase from room temperature to 300 ℃, while the Cu/Al system showed a sharp increase (~150%) between 125℃ and 200℃. This distinct strengthening behavior is attributed to solid solution formation in Cu/Ni and diffusion-activated intermetallic formation in Cu/Al.

The development of Al-Ni alloys with a controlled microstructure has had a great impact on the field of study of aluminum-based alloys. In the present research, the influence of thermal parameters on the grain structures resulting from the directional solidification process of Al-Ni alloys with different alloy content has been studied. It has also been evaluated how different structures and the distribution of second phases influence the corrosion behavior and microhardness of alloys. The columnar-to-equiaxed transition (CET) was observed to occur when the temperature gradient in the melt decreased to values between 1.3 to 2.9 ° C/cm. In addition, a small increase in the microhardness values was observed as a function of the Ni-content. When the Ni-content increase, the resistance to polarization decreases for samples with equiaxed grain structure, throughout the range of compositions studied. Furthermore, the equiaxed grain structure presents higher resistance to polarization values than the columnar grain zone, for alloys with a composition equal to or lower than the eutectic composition.

The framework proposed by Alison Druin about 20 years ago, which defined the roles children play in technology design, has been widely adopted by the Child-Computer Interaction (CCI) community. While some studies have adopted relevant roles as presented in the framework, others have argued for extending the framework to include newly identified roles. Still, other studies argue that Druin's framework failed to account for roles children may take up as they interact with peers or with tools. Consequently, this systematic literature review examines children’s emerging and changing roles in the codesign of new technologies. Specifically, we answered the research question: What new roles emerge in research as children co-design new technologies? Our effort aims at providing evidence of new roles children have adopted in literature, which may help researchers in the CCI community make more informed decisions about participatory design approaches with children.

Ocean big data is the scientific practice of using big data technology in the marine field. Data from satellites, manned spacecraft, space stations, airship, unmanned aerial vehicles, shore-based radar and observation stations, exploration platforms, buoys, underwater gliders, submersibles, and submarine observation networks are seamlessly combined into the ocean’s big data. Increasing numbers of scholars have tried to fully analyze the ocean’s big data. To explore the key research technology knowledge graphs related to ocean big data, articles between 1990 and 2020 were collected from the “Web of Science”. By comparing bibliometric software and using the visualization software Cite-Space, the pivotal literature related to ocean big data, as well as countries, institutions, categories, and keywords, were visualized and recognized. Journal co-citation analysis networks can help determine the national distribution of core journals. Co-citation analysis networks for documents show authors who are influential at key technical levels. Key co-occurrence analysis network keywords can determine research hot spots and research frontiers. The three supporting elements of marine big data research are shown in the co-citation network. These elements are author, institution, and country. By examining the co-occurrence of keywords, the key technology research directions for future marine big data were determined.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Biogas contains more than 40% CO2 that can be removed to produce high quality CH4. Recently, CH4 production from CO2 methanation has been reported in several studies. In this study, CO2 methanation of biogas was performed over a 20 wt% Ni-Mg-Al catalyst, and the effects of CO2 conversion rate and CH4 selectivity were investigated as a function of CH4, O2, H2O, and N2 compositions of the biogas. At a gas hourly space velocity (GHSV) of 30,000/h, the CO2 conversion rate was ~79.3% with a CH4 selectivity of 95%. In addition, the effects of the reaction temperature (200–450 °C), GHSV (21,000–50,000/h), and H2/CO2 molar ratio (3–5) on the CO2 conversion rate and CH4 selectivity over the 20 wt% Ni-Mg-Al catalyst were evaluated. The characteristics of the catalyst were analyzed using Brunauer-Emmett-Teller (BET) surface area analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). The catalyst was stable for approximately 200 h at a GHSV of 30,000/h and a reaction temperature of 350 °C. CO2 conversion and CH4 selectivity were maintained at 75% and 93%, respectively, and the catalyst was therefore concluded to exhibit stable activity.

In this work, the Ni/Ti/Nb multilayer composite was successfully manufactured by accumulative pack-roll bonding. The microstructure evolution and mechanical properties of the composite during the accumulative roll bonding (ARB) process were investigated by scanning electron microscopy(SEM), energy dispersive spectrometer(EDS), transmission electron microscopy (TEM), micro-hardness and tensile tests. The results showed that after 5 passes of the ARB process, the deformations of layers were relatively uniform, and no large number of interlayer fractures occurred. The microstructures of Ni and Ti were both equiaxed grains with a grain size of 200 nm and 150 nm, respectively, and finer equiaxed grains of the Ni layer were observed at the interface. The laminar structure of Nb layer was observed. The tensile strength and micro-hardness increased significantly as the number of ARB increased. After 5 passes of the ARB process, the tensile strength of the composite reached 792.3 MPa, and the micro-hardness of Ni, Ti, and Nb were increased to 270.2, 307.4, and 243.4 HV, respectively.

This article reports the two-step synthesis of NiFeO_x nanomaterials, their characterisation and bifunctional electrocatalytic activity measurements in alkaline electrolyte for metal-air batteries. The samples were mostly in layered double hydroxide at the initial temperature, but upon heat treatment, they were converted to NiFe₂O₄ phases. The electrochemical behaviour of the different samples was studied by linear sweep voltammetry and cyclic voltammetry on the glassy carbon electrode. The OER catalyst activity was observed for low mass loadings (0.125 mg cm⁻²), whereas high catalyst loading exhibited the best performance on the ORR side. The sample heat treated at 250 °C delivered the highest bi-functional oxygen evolution and reduction reaction activity (OER/ORR) thanks to its thin-holey nanosheet like structure with higher nickel oxidation state at 250 °C. This work further helps to develop low-cost electrocatalyst development for metal-air batteries.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Integrating sustainable processes and innovative waste utilization not only addresses environ-mental challenges but also aligns with evaluating energy sustainability and creating the circular waste management. This study presents a comparative analysis of liquid fuel production from waste tires and water hyacinth using two thermochemical methods: co-pyrolysis (direct method) and co-gasification integrated with the Fischer-Tropsch (FT) process (indirect method). The As-pen Plus simulation software version 9 is employed to develop models, determining optimal operating conditions for maximum liquid fuel, and assessing economic viability. Co-pyrolysis simulations reveal an increase in oil products and a decrease in gas products with higher blending weight ratios of waste tires/water hyacinth (W/B) and lower pyrolyser temperatures. Operating at 400°C with a blending weight ratio of 75:25 provided the maximum liquid fuel rate of 6649.22 gal/day. For co-gasification, optimal conditions (W/B = 50:50, T = 800°C, steam to feed ratio (S/F) = 1) result in the highest syngas yield of 115.92 kmol/h. Fischer-Tropsch simulations demonstrate an increase in gasoline and a decrease in diesel with rising reactor temperatures. At 230°C, the maximum liquid fuel rate reaches 8817.15 gal/day. The economic and production yield analysis indicates that the indirect method better than the direct method, providing higher liquid fuel yields and investment worthiness.

The severe respiratory distress syndrome (SRDS) has been a significant clinical issue in modern respiratory medicine. Its role in COVID-19 pandemic is not well defined. Outside-the-hospital SRDS is usually community-acquired septic pneumonia; however, in-hospitals incidences are complicated by co-infections. While SRDS is genetically selected in European and African origins, these are not clear in Middle East, particularly in COVID-19 backgrounds. There is a severe paucity in high quality data on correlations between COVID-19, ARDS, co-infectome, and patient demographics. We have conducted a comprehensive investigation on 298 patients for associations of SRDS, coinfections, and patient demographics on COVID-19 patients’ outcomes. Of these, 9.4% (n=28) had SRDS, and the rest (90.6%) had not. 54% of those with SRDS died while 84% survived; SRDS fatality was highly significant (Chi-square test P-value = 0.00000246). Irrespective of gender, the age of patients was significantly associated with SRDS (72.9 +/-8.9) compared to those without it (56.2 +/-15.1). However, there was no significant difference neither in the age of admitted patients before COVID-19 (58.5 +/-15.3) and during COVID-19 (57.2 +/-15.5) nor in the gender and COVID-19 fatality (Fisher Exact test 2-sided 1.000, 1-sided .546) ruling out that SRDS age-specificity were selected by virus susceptibility. A 100% of SRDS patients without bacterial co-infections survived while only 25% of those with co- infectome did not; this association was highly significant (P value= 0.00041). Co-infections alone without underlying SRDS was also associated with high fatality among patients (P value= 0.00000000076). Almost all COVID-19 patients without co-infectome (99.2%) survived while 28% of those with bacterial co-infection died. The major bacterial pathogens that potentially predisposed to SRDS, were Acinetobacter baumannii, and Escherichia coli either alone or in a mixed infection with Klebsiella pneumoniae were predominant species identified during SRDS attack. Thus, Gram-negative co-infectome potentially induced fatal SRDS aggravating COVID-19 outcome. These findings have significant clinical implications in specific differential diagnosis of SRDS syndromes for subsequent empiric therapy and patient management strategies. Future vertical investigation for similar mechanisms of cytokine-induced SRDS by Gram negative pathogens is imperative since hypervirulent strains are rapidly circulating in the region. The study is limited by a single center study confined to Ha’il hospitals; large scale investigation in major national hospitals would gain more insights.

Leishmania parasites present astonishing adaptative abilities that represent a matter of life or death within disparate environments during the heteroxenous parasite life cycle. From an evolutionary perspective, organisms develop methods of overcoming such challenges. Strategies that extend beyond the genetic diversity have been discussed and include variability between parasite cells during the infections of their hosts. The occurrence of Leishmania subpopulation fluctuations with variable structural genomic contents demonstrates that a single strain might shelter the variability required to overcome inconsistent environments. Such intrastrain variability provides parasites with an extraordinary ability to adapt and thus survive and propagate. However, different perspectives on this evolution have been proposed. Strains or species living in the same environment can cooperate but also compete. These interactions might increase the replication rate of some parasites but cause the loss of more aggressive competitors for others. Adaptive responses to intra- and interspecific competition can evolve as a fixed strategy (replication is adapted to the average genetic complexity of infections) or an optional strategy (replication varies according to the genetic complexity of the current infection). This review highlights the complexity of interspecies and intrastrain interactions among Leishmania parasites as well as the different factors that influence this interplay.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Keywords: glycerin; Ni-based catalyst; lanthanum; semi-industrial scale; hydrogen production; biorefinery; monitoring.

This study demonstrates the successful synthesis of Ni/Y2O3 nanocomposite particles through the application of ultrasound-assisted precipitation using the Ultrasonic Spray Pyrolysis technique. The particle size was predicted accurately using a modified equation, and they were collected in a water suspension with Polyvinylpyrrolidone (PVP) as the stabiliser. The presence of the Y2O3 core and Ni shell was confirmed with Transmission Electron Microscopy (TEM) and with electron diffraction. The TEM observations revealed the formation of round particles with an average diameter of 466 nm, while the lattice parameter on the Ni particle’s surface was measured to be 0.343 nm. The Ni/Y2O3 nanocomposite particle suspensions were lyophilized, to obtain a dried material that was suitable for embedding into a Polylactic acid (PLA) matrix. The resulting PLA/Ni/Y2O3 composite material was successfully extruded successfully, so that a 3D printed technology Fused Filament Fabrication could be used further for the production of tensile test tubes. The tensile tests showed that the addition of lyophilised Ni/Y2O3 into the PLA matrix decreased the tensile strength by 21.8 %, while the tensile modulus was not influenced. Dynamic Mechanical Analysis (DMA) showed that the addition of the Ni/Y2O3 particles increased the glass transition temperature by 5 °C, and increased the storage modulus in the glass transition range significantly. These findings demonstrate the potential for utilising Ni/Y2O3 nanocomposite particles in 3D printing applications, and warrant further exploration of their mechanical properties and potential applications in various fields.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

New setting is introduced to study types of coloring numbers, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Different types of procedures including neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are proposed in this way, some results are obtained. General classes of neutrosophic hypergraphs are used to obtain chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic hypergraphs. Using colors to assign to the vertices of neutrosophic hypergraphs and characterizing representatives of the colors are applied in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. Some questions and problems are posed concerning ways to do further studies on this topic. Using different ways of study on neutrosophic hypergraphs to get new results about number, degree and co-degree in the way that some number, degree and co-degree get understandable perspective. Neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs are studied to investigate about the notions, coloring, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges in neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs. In this way, sets of representatives of colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges have key points to get new results but in some cases, there are usages of sets and numbers instead of optimal ones. Simultaneously, notions chromatic number, the representatives of the colors, degree of vertices, degree of hyperedges, co-degree of vertices, co-degree of hyperedges, neutrosophic degree of vertices, neutrosophic degree of hyperedges, neutrosophic co-degree of vertices, neutrosophic co-degree of hyperedges, neutrosophic number of vertices, neutrosophic number of hyperedges are applied into neutrosophic hypergraphs, especially, neutrosophic (r, n)−regular hypergraphs and neutrosophic complete r−partite hypergraphs to get sensible results about their structures. Basic familiarities with neutrosophic hypergraphs theory and hypergraph theory are proposed for this article.

At Mae-Moh power plant, Thailand, superheater tubes, which are exposed in fly ash environ-ment, often degrade due to solid particle erosion. To extend the service lifetime of the superheater tubes, the high velocity oxy-fuel (HVOF) thermal spray technique is used to deposit a protective coating on the material, SA213-T22 steel. In this work, the solid particle erosion of the Co-28Cr and WC-12Co coatings was investigated using erodent particle impingement at the angles of 30o and 90o with an average particle size of 60 μm. The erosion behavior of SA213-T22 with and without Co-28Cr and WC-12Co coatings was explained using ductile and brittle erosion modes. The erosion test resulted in the brittle mode for both Co-28Cr and WC-12Co coatings, while SA213-T22 without coating indicated the ductile mode. On the investigation of surface morphology, the Co-28Cr coating showed mostly microcracks in contrast with the WC-12Co coating, fracture, de-bonding and deep cavities were also observed. Erosion resistance of the Co-28Cr coating was significantly higher than the WC-12Co coating, due to high hardness, low porosity and high density of the coating.

The main objective of this paper is to identify the major research areas of ChatGPT through term and keyword co-occurrence network mapping techniques. For conducting the present study, total of 577 publications were retrieved from the Lens database for the network visualization. The findings of the study showed that “chatgpt” occurrence in maximum number of times followed by its related terms such as artificial intelligence, large language model, gpt, study etc. This study will be helpful to library and information science as well as computer or information technology professionals.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

Frailty, an age-related decline in homeostatic reserves, markedly proceeded during the coronavirus disease 2019 pandemic. To continuously assess frailty status, a remote system is urgently required. We aimed to co-design/co-develop an online frailty check (FC) application alongside FC supporters who were facilitators in a pre-existing onsite FC program. The online FC included a screening measurement for sarcopenia and an 11-item questionnaire covering dietary, physical, and social behaviors. Using prototype applications, 55 opinions obtained from 32 FC supporters (median 74.0 years) were categorized and reflected refinement. Regarding the self-efficacy of FC supporters, a significant increase in social positioning was seen after the mock test (P=.031). For FC supporters and participants, the average system usability scale (SUS) score was 70.2±10.3 points, which was “marginally high” for acceptability and “good” for the adjective range. Multiple regression analysis showed that the SUS score was significantly correlated with online-onsite reliability but not online communication, even after adjusting by age, sex, education level, and ICT proficiency (b=0.400, 95% CI: 0.243-1.951, P=.013). Additionally, a significant association between onsite and online FC scores was observed (R=0.670, P=.001). Our online FC application was evaluated to be a valuable tool to practically assess frailty status remotely.

Rare diseases are characterized by a wide diversity of signs and symptoms and vary not only from disease to disease, but also from person to person, and living with a disease leads patients to peculiar experiences and treatments, without limits of time and space, as they extend to various environments and relationships of their lives. The objective of this study is the theoretical interaction between Value Co-creation (VC) and the Stakeholder Theory (ST) with the Shared Decision Making (SDM) health care theory. It is configured as a multiparadigmatic proposal by enabling the analysis of multiple perspectives of different stakeholders in health care. Thus, Co-created Decision Making (CDM) emerges in a logic dominated by service, with emphasis on intangible aspects and the interactivity of the relationships. It goes beyond the clinical office and the doctor-patient relationships, as studied in SDM, extending to all environments and interactions that add value to the patient's treatment. It was concluded that the essence of this new theory proposed here is neither in patient-centered care nor in patient self-care, but in co-created relationships with and between stakeholders in both directions, including non-health care environments that are important to the patient, such as relationships with friends, family, other patients with the same disease, social media, public policies, and the practice of pleasurable activities.

Recently, many authors have been interested to introduce fuzzy implications over t-norms and t-conorms. In this paper, we introduce (S,N) and residuum fuzzy implication for Dubois t-norm and Hamacher's t-norm. Also, new concepts so-called (T,N) and residual fuzzy co-implication in dual Heyting Algebra are investigated. Some examples as well as application are discussed as well.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Authors such as Schnoebelen (2012: 12) suggest that in some languages (cf. Navajo) certain dependent clauses are frequently used independently to “mark emotional evaluation and background information”. Evans (2007) uses the term insubordination to refer to this phenomenon. Our study focuses on a particular insubordinate construction introduced by the sequence ni que in Spanish, as in the example [¡Una carta cada día!] Ni que yo fuese Umbral. (CORPES 100), used as an independent clause with a sociopragmatic meaning which is different from that of its subordinate counterpart (cf. No escribiría una carta cada día ni que yo fuese Umbral). Our research questions ask about the potential for ni que to be used as a discourse marker fulfilling an expressive function when it introduces this type of construction, and the derived hypothesis is then oriented to test whether Schnoebelen's (2012) observation about insubordinate constructions applies also to this Spanish construction. In order to test this hypothesis, we performed a functional-discourse analysis of more than 2000 concordances (and their extended contexts) in Mark Davies' Corpus del Español and the Real Academia CORPES XXI. Our findings show that the insubordinate construction differs in function and meaning from its subordinate counterpart, the former fulfilling a stronger emotive function, often combined with other discourse-pragmatic functions, such as evaluation or the organization of discourse.

Metal hydrides are one of the types of functional materials that allow safe and compact storage of a large amount of hydrogen, which is increasingly used today as an alternate fuel or energy source. The possibility of obtaining the initial energy necessary for the production of hydrogen by electrolysis process from renewable energy sources, such as solar panels and wind generators, makes hydrogen energetic quite attractive and rapidly developing industry sector. Solid form of hydrogen storage with the possibility of reversible sorption, gives opportunity for creation autonomous energy storage systems. La-Ni based alloys allow hydrogen storing at ambient temperatures and pressure not higher than 15 bar, which makes the application of these alloys quite practical, interesting and prospects for analysis and modifications on the ways of stored hydrogen capacity increasing, alloys price reducing and application for renewable energy storage.

As one of the important components of underwater propulsion systems, water lubricated bearings are often failure due to mechanical wearing and vibrating, especially under high loads and prolonged friction. In this paper, a dual-network co-crosslinking strategy based on HNBR is proposed, in which the epoxy network connects with the rubber network through Epoxidized Eommia ulmoides gum. The damping, tribological and mechanical properties of the prepared composite are systematically investigated. The results show that this material has excellent friction and vibration damping properties, with a water-lubricated coefficient of friction as low as 0.022 and a wear resistance as high as 3.87 × 10-6mm3/Nm. Preparing HNBR-based composite by dual network co-crosslinked is proved being a feasible solution to improve the reliability and service life of water-lubricated bearings.

The 2022-2023 influenza season in Romania was characterized by high pediatric hospitalization rates, predominated by influenza A subtypes H1N1 and H3N2. Lowered population immunity to influenza after the SARS-CoV-2 pandemic and subsequent stoppage of influenza circulation, particularly in children who had limited pre-pandemic exposures, influenced hospitalization among children immunosuppressed, and patients with concurrent medical conditions who are at increased risk for developing severe forms of influenza. This study focused on the characteristics of influenza issues among paediatric patients, as well as the relationship between different influenza virus types and viral and bacterial coinfections and illness severity in the 2022-2023 season after the SARS-CoV-2 pandemic. We conducted a retrospective clinical analysis on 301 cases of influenza in pediatric inpatients (age ≤ 18 years), hospitalized at the National Institute of Infectious Diseases "Prof. Dr. Matei Balș" IX Pediatric Infectious Diseases Clinical Section between October 2022 and February 2023. The most significant age group was 57.8% representing children between one to four years old and female. The average clinical forms were found in 61.7%, whereas severe versions represented 18.2% of cases. Most of the complications were respiratory (acute interstitial pneumonia, 76.1%), hematological (72.1%), represented by intra-infectious and deficiency anemia, leukopenia, thrombocytopenia), 33.6% were digestive, such as diarrheal disease, liver cytolysis syndrome, and the acute dehydration syndrome associated with electrolyte imbalance (71.4%). Severe complications were associated with a risk of unfavorable evolution: acute respiratory failure and neurological complications (convulsions, encephalitis). No deaths were reported. We noticed that the flu season 2022-2023 was characterized by the association of co-infections (viral, bacterial, fungal and parasitic) more frequent than in previous years (26.2% vs. 16%), which evolved more severely, with prolonged hospitalization and more complications (p<0.05), and time of use of oxygen therapy was statistically significant (p > 0.05); influenza vaccination in this group was zero. In conclusion, coinfections with respiratory viruses increase the severity of the pediatric population's immunity to influenza, especially among young children who are more vulnerable to developing a serious illness. All people above the age of six months should get vaccinated against influenza to prevent the illness and its severe complications.

Recently, the amount of waste generated has been rapidly increasing, there have been difficulties disposing of waste in Korea. As a solution to this, treating waste using a cement kiln has suggested, but the environmental and economic effects have not been specifically studied. In this study, the effects of alternative resources, and reducing the social costs(Installation and Operation) associated with waste treatment facilities were analyzed. Through a co-processing method, a reduction of approximately 53kg of CO2 can be realized during the production of one ton of cement, and cost savings of about 3,815 milion USD. Another effect is an extension of the expiration date for landfills by 7.55 years.

New setting is introduced to study quasi-degree and quasi-co-degree arising from co-neighborhood. quasi-degree and quasi-co-degree is about a vertex which are applied into the setting of neutrosophic graphs. . The structure of set is studied and general results are obtained. Also, some classes of neutrosophic graphs namely path-neutrosophic graphs, cycle-neutrosophic graphs, complete-neutrosophic graphs and star-neutrosophic graphs, complete-bipartite-neutrosophic graphs and complete-multipartite-neutrosophic graphs are investigated in the terms of a vertex which is called either quasi-degree or quasi-co-degree. Neutrosophic number is reused in this way. It’s applied to use the type of neutrosophic number in the way that, three values of a vertex are used and they’ve same share to construct this number to compare with other vertices. Summation of three values of vertex makes one number and applying it to a comparison. This approach facilitates identifying vertices which form quasi-degree and quasi-co-degree. Quasi-degree is a value of a vertex which is maximum amid all values of vertices which are neighbors to a fixed vertex. Quasi-co-degree is a value of an edge which is maximum amid all values of edges which are neighbors to a fixed vertex but corresponded vertex is representative for this notion. Using different values which are related to a vertex inspire us to focus on edge and vertices which are corresponded to a fixed vertex. The notion of neighborhood is used to collect either vertices are titled neighbors or edges are incident to fixed vertex. In both settings, some classes of well-known neutrosophic graphs are studied. Some clarifications for each result and each definitions are provided. Using fixed vertex has key role to have these notions in the form of vertex or edge. The value of an edge has eligibility to call quasi-co-degree but the value of a vertex has eligibility to call quasi-degree. Some results get more frameworks and perspective about these definitions. The way in that, two vertices have connection together, open the way to define neighborhood and co-neighborhood. The maximum values in neighborhood and co-neighborhood introduces quasi-degree and quasi-co-degree, respectively. New name is chosen from degree. Since amid all vertices with different degrees, one vertex is chosen. In other words, one vertex is fixed and its degree turns out quasi-degree where two degrees could be assigned to a vertex. Degree of edges and degree of vertices. The number of edges which are incident to the vertex and the number of vertices which are neighbors to the vertex. Degree and co-degree are the notions which are transformed to use in quasi-style. Two neutrosophic values introduce two neutrosophic vertices separately in each settings. These notions are applied into neutrosophic graphs as individuals but not family of them as drawbacks for these notions. Finding special neutrosophic graphs which are well-known, is an open way to purse this study. Some problems are proposed to pursue this study. Basic familiarities with graph theory and neutrosophic graph theory are proposed for this article.

Potential of co-digestion mixing thickened secondary sludge (TS) from extended aeration wastewater treatment plant and locally available substrates (whey, grease and septage) has been studied using three steps. The first step was a batch test to determine biological methane potential (BMP) of different mixtures of the three co-substrates with TS. The second step has been carried out with lab-scale reactors (20 L) simulating anaerobic continuous stirred tank reactors fed by three mixtures of co-substrates determined according to previous step results. Modelling using ADM1 as a mechanistic model was applied in the third step to help understanding the co-digestion process. According to BMP step, septage used as co-substrate has a negative effect on performance and addition of 10 to 30% grease or 10% whey would lead to a higher production of biogas and with an increase of the methane content. The results from the reactor showed less evi-dence of the positive effects observed with the BMP assay. Protein and lipid fractions of particu-late biodegradable COD are important variables for digester stability and methane production as predicted by modelling. Results of simulations with ADM1 model adapted to co-digestion confirmed that this model is a powerful tool to optimize the process of biogas production.

There is compelling evidence that the nuclear receptor TRβ, a member of the thyroid hormone receptor (TR) family, is a tumor suppressor in thyroid, breast and other solid tumors. Cell-based and animal studies reveal that the liganded TRβ induces apoptosis, reduces an aggressive phenotype, decreases stem cell populations, and slows tumor growth through modulation of a complex interplay of transcriptional networks. TRβ-driven tumor suppressive transcriptomic signatures include repression of known drivers of proliferation such as PI3K/Akt pathway and activation of novel signaling (JAK1/STAT1) and metabolic reprogramming in both thyroid and breast cancers. The presence of TRβ is also correlated with a positive prognosis and response to therapeutics in BRCA+ and triple-negative breast cancers respectively. Ligand activation of TRβ enhances sensitivity to chemotherapeutics. TRβ co-regulators and bromodomain-containing chromatin remodeling proteins are emergent therapeutic targets. This review considers TRβ as a potential biomolecular diagnostic and therapeutic target.

The sense of uncertainty and fragility due to the effects and magnitude of global challenges we are facing (from pandemic circumstances to climate change impacts) requires – much more than in the past – the capacity to generate a visionary and forefront design approach in the young gen-erations aiming at stimulating their reaction attitude rather than providing consolidated tools from past conditions that no longer exist or will rapidly evolve. Within this general framework, we have investigated the effectiveness and impacts of experienced-based methods of learning and innovative educational tools in architecture aimed at shaping expertise in which the environ-mental dimension and the climate-change challenge dialogues with the context's complexity in terms of socio-cultural dynamics, real potentialities and constrains, addressing their transdisci-plinary trajectories. The paper analyses 5 international pioneering teaching experiences that provide the opportunity to understand the outcomes of collaborative and experiential learning processes in which the educational activities leverage a dialogue between diverse communities (academia-citizens-policymakers-practitioners). The study outcomes show that shifting the pedagogical paradigm towards in-field-experience-based models can improve the awareness of future practitioners for climate implications of architectural design, implement their analysis and project skills while triggering processes of knowledge transfer and co-production at community level, and allow them to better address the societal and cultural issues involved within decision making.

The purpose of this study is to explore conceptual approaches in co-production studies and to examine current research trends of the study. The conceptual paper includes research articles related to co-production in public administration field. By thoroughly scrutinizing 32 research works of co-production, this study highlights major loopholes in the field of the study. The contributions of the study are: (1) identifying two common characteristics of co-production, (2) categorising three types of co-producing by end-users, and (3) finding that goals and success of co-production are more beneficial for service providers though its initial approach is citizen-centric approach. We suggest that future studies should be (1) to focus on reasons for co-production failures or success, (2) to discover further hindrances for co-production in service production, (3) to examine influencing factors on service providers as well as institutional impacts on co-production process, and (4) to include practical assessment in co-production study.

Elevated antimony concentrations in aqueous environments from anthropogenic sources is becoming of global concern, here iron oxides are known to strongly adsorb aqueous antimony species with different oxidation states, but the effect of silica on the removal characteristics is not well understood despite being a common component in the environment. In this study, ferrihydrite was synthesized at various Si/Fe molar ratios to investigate its adsorption and co-precipitation behaviors with aqueous antimony anionic species, Sb(III) and Sb(V). The XRD analyses of the precipitates showed two broad diffraction features at approximately 35° and 62° 2θ, which are characteristic of 2-line ferrihydrite, no significant shifts in peak positions in the ferrihydrite regardless of the Si/Fe ratios. The infrared spectra showed a sharp band at ~990 cm⁻¹, corresponding to asymmetric stretching vibrations of Si-O-Fe bonds which increased in intensity with increasing Si/Fe molar ratios. Further, the surface charge on the precipitates became more negative with increasing Si/Fe molar ratios. The adsorption experiments indicated that Sb(V) was preferentially adsorbed at acidic conditions and decreased dramatically with increasing pH while the adsorption rate of Sb(III) ions was independent of pH, however, the presence of silica suppressed the adsorption of both Sb(III) and Sb(V) ions. The results showed that Sb(III) and Sb(V) ions were significantly inhibited by co-precipitation with ferrihydrite even in the presence of silica by isomorphous substitution in the ferrihydrite crystal structure.

Background: Previously, our laboratory has provided evidence that pre-administration of the antioxidant, lipoic acid covalently bonded to various naturally occurring antioxidants, enhanced neuroprotective capacity compared to the administration of lipoic acid on its own. The naturally occurring compound scopoletin, a coumarin derivative, has been shown in various in vitro studies to have both antioxidant and anti-inflammatory mechanism of actions. To date, the effect of scopoletin on neuronal cell death in an in vivo model of ischemia or ischemia-reperfusion has not been investigated. Therefore, the present investigation was designed to determine if scopoletin on its own, or a co-drug consisting of lipoic acid and scopoletin covalent bond, named UPEI-400, would be capable of demonstrating a similar neuroprotective efficacy. Methods: Using a rodent model of stroke in male rats (anesthetized with Inactin®; 100 mg/kg, iv), the middle cerebral artery was permanently occluded for 6 hours (pMCAO), or in separate animals, occluded for 30 min followed by 5.5 hrs of reperfusion (ischemia/reperfusion; I/R). Results: Pre-administration of either scopoletin or UPEI-400 significantly decreased infarct volume in the I/R model (p<0.05), but not in the pMCAO model of stroke. However, UPEI-400 was ~1000 times more potent as compared to scopoletin on its own. The optimal dose of UPEI-400 was then injected during the occlusion and at several time points during reperfusion and significant neuroprotection was observed for up to 150 mins following the start of reperfusion (p<0.05). Conclusion: The data suggest that synthetic combination of scopoletin with lipoic acid (UPEI-400) is a more effective neuroprotectant that either compound on their own. Also, since UPEI-400 was only effective in a model of I/R, it is possible that it may act to enhance neuronal antioxidant capacity and/or upregulate anti-inflammatory pathways to prevent the neuronal cell death.

Poly(vinyl butyral-co-vinyl alcohol-co-vinyl acetate) named further PVBA was investigated as protective coating for copper corrosion in 0.9 % NaCl solution using electrochemical measurements such as, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization associated with Atomic Force Microscopy (AFM). The PVBA coating on the copper surface (Cu-PVBA) was modeled in methanol containing PVBA. Its inhibitory properties against corrosion was comparatively discussed with those of the copper sample treated in methanol without polymer (Cu-Me) and of untreated sample (standard copper). A protective performance of PVBA coating of 80 % was computed from electrochemical measurements, for copper corrosion in NaCl solution. Also, AFM images designed a specific surface morphology of coated surface with PVBA, clearly highlighting a polymer film adsorbed on the copper surface, which presents certain deterioration after corrosion, but metal surface was not significantly affected compared to those of untreated samples or treated in methanol, in the absence of PVBA.

New setting is introduced to study co-neighborhood, neutrosophic t-neighborhood, neutrosophic quasi-vertex set, neutrosophic quasi-order, neutrosophic neighborhood, neutrosophic co-t-neighborhood, neutrosophic quasi-edge set, neutrosophic quasi-size, Neutrosophic number, neutrosophic co-neighborhood, co-neutrosophic number, quasi-number and quasi-co-number. Some classes of neutrosophic graphs are investigated.

The soil microbial community serves as a crucial indicator for assessing soil fertility and health. The composition and activity of soil microorganisms reflect the soil's well-being and its ability to provide proper nutrients for crops. Fertilization plays a prominent role in enhancing soil fertility, and novel types of fertilizers, such as stabilized fertilizers with nitrification/urease inhibitors and coated fertilizers, have gained popularity in rice and maize cultivation. However, the long-term effects of these stabilized and coated urea fertilizers on soil chemical properties, microbial di-versity and community structure, as well as nitrogen cycling functional genes, remain unclear. Therefore, it is essential to investigate the impact of extended use of stabilized and coated urea fertilizers on soil fertility and microbiota in rice paddy fields. This research will provide scientific and theoretical support for the development and promotion of stabilized and coated urea ferti-lizers. To examine the effects of long-term application of these stabilized and coated urea fertilizers on soil chemical properties and microorganisms in rice paddy fields, soil samples were collected from brown soil rice paddy fields treated with various urease and nitrification inhibitors, stable urea, sulfur-coated urea (SCU), and resin-coated urea (PCU). The study revealed that 16 years of long-term use of conventional urea nitrogen fertilizer led to a considerable reduction in soil TP. On the other hand, NBPT and conventional urea fertilizers, when applied for an extended period, significantly increased soil organic matter (SOM). Moreover, except for HQ and NBPT+DMPP, the prolonged application of new urea fertilizers also signifi-cantly enhanced soil total potassium (TK). Notably, among all the treatments, PCU treatment had higher values for various soil chemical properties. In the case of SCU fertilizer used in brown soil rice paddy fields, it resulted in a significant decrease in soil pH over time. However, this change in pH did not affect the population of ammonia-oxidizing bacteria (AOB), as it was primarily in-fluenced by soil available nitrogen. DMPP, HQ+DCD, NBPT+DMPP, SCU, and PCU significantly reduced the copy number of bacterial 16S rRNA genes in the soil, with the coated urea fertilizers (SCU and PCU) having a greater impact. The long-term use of stabilized urea fertilizers containing HQ significantly reduced the bacterial community in rice paddy soil. Conversely, HQ+DCD stable urea fertilizer significantly increased the population structure and abundance of Basidiomycota fungi while decreasing the population structure and abundance of Rozellomycota fungi. DMPP stabilized urea fertilizer notably increased the population structure and abundance of Ascomycota fungi while decreasing the population structure and abundance of Rozellmycota and Chytridiomycota fungi. Further-more, HQ stabilized urea fertilizer significantly reduced the population structure and abundance of Chytridiomycota fungi. It is important to note that SCU fertilizer is not suitable for long-term application in neutral to slightly acidic meadow brown soil with a background pH. On the other hand, stable urea fertilizers and resin-coated urea fertilizers containing HQ, NBPT, DCD, DMPP, and their combinations are suitable for long-term application in neutral to slightly acidic meadow brown soil.

Type 2 Diabetes Mellitus (T2DM) is one of the most common metabolic disorders, with a major involvement of oxidative stress in its onset and progression. Pioglitazone (Pio) is an antidiabetic drug which primarily works by reducing insulin resistance while Curcumin (Cur) is powerful antioxidant with o important hypoglycemic effect, also. The both drugs are associated with several drawbacks, such as reduced bioavailability, a short half-life time (Pio) as well as instability and poor water solubility (Cur), which limit their therapeutic use. In order to overcome these disadvantages, a new co-delivery (Pio, Cur) nanosystem based chitosan (CS) (CS-Pio-Cur NPs), was developed, and characterized in reference with simple nanosystems (CS-Pio NPs, CS-Cur NPs). The developed CS-based NPs (CS-Pio-Cur NPs, CS-Pio NPs, CS-Cur NPs) were physico-chemical characterized in terms of particle size (PS), entrapment efficiency (EF%) and loading capacity (LC%). The CS-Pio-Cur NPs proved increased or similar values of EE (88.95% ± 7.79 for Cur; 94.83% ± 9.89 for Pio) and LC% (24.25 % ± 1.62 for Cur; 3.5% ± 0.98 for Pio), in reference with simple nanosystems, CS-Cur NPs (EE = 82.46% ± 1.74; LC = 20.34% ± 0.94) and CS-Pio NPs) (EE = 96.31% ± 0.68; LC = 4.11% ± 0.47), respectively. The identification of APIs (Cur, Pio) loaded into CS matrix was performed using FR-IR spectroscopy and for simultaneously quantification of APIs (Cur, Pio) released from CS-Pio-Cur NPs, a HLPC method was developed and validated. Based on release study performed in different simulated fluids (SGF, SIF, SCF) it can be appreciated that developed CS-APIs NPs have favorable pharmacokinetic profile with good release in gastrointestinal tract.

The COVID-19 pandemic and tuberculosis have epidemiological similarities, being transmitted airborne, favored by direct contact, crowded environments and vulnerable biological status. We performed a retrospective study of 45 cases of pulmonary tuberculosis associated with COVID-19 (TB+COV+) compared to 45 cases with tuberculous monoinfection (TB+COV-), hospitalized during 2021-2022. The demographic characteristics were similar in the two groups, predominating men, a median age of 51 years, living in rural areas, medium level of education and smoking. Common symptoms of the two groups were cough, weight loss, profuse sweating, loss of appetite and hemoptysis, while fever, headache, myo-arthralgias and digestive symptoms characterized the TB+COV+ forms. The scores of radiological lesions in the TB+COV+ compared to TB+COV- group were significantly higher and persistent, revealing more frequent bilateral extensive lung lesions. There were no significant differences in the biological parameters between the two groups. Mortality was 2.2%, regardless of the association of COVID-19. The frequency of infections with Clostridioides difficile was higher in TB+COV+ cases. In conclusion, the co-infection of COVID-19 had an impact on the clinical and biological expression of tuberculosis diagnosed in a pandemic context.

The amalgamation of mineral and targeted bacterial preparations represents a new generation of agricultural technology. Inoculation with combined preparations of microorganisms is more effective than inoculation with a single microorganism in stimulating plant growth by providing a more balanced diet for various crops. In this work, the effect of inoculation of 20 consortium variants on the yield indicators of three crops (wheat, buckwheat, corn) and the soil microbiome in the open field was investigated. The soil microbiome was defined by 16S rRNA sequences through NGS. Species richness of the soil microbial community (alpha diversity) was similar for all studied samples. Beta-diversity analysis revealed that the microbial diversity of three soil samples (C.bw, F.bw and Soil.bw) differed significantly from all others. At the phylum level, the number of Acidobacteriota and Firmicutes in these samples was increased. For the combination “Consortium C (Rothia endophytic GMG9 and Azotobacter chroococcum GMG39) - buckwheat”, a systemic positive improvement in all growth and yield indicators was observed. The soil of the site where buckwheat grew, inoculated by Consortium C, contained significantly more available phosphorus than all other soil samples. Such results can be explained both by the direct action of a consortium of phosphate-immobilizing and nitrogen-fixing bacteria and to acidification of the medium due to an increase in phylum Acidobacteriota bacteria in the soil.

This paper presents a novel cheminformatics approach for the design and synthesis of hydroxyapatite/collagen nanocomposites, which have potential biomedical applications in tissue engineering, drug delivery, orthopedic and dental implants. The nanocomposites are synthesized by the co-precipitation method with different ratios of hydroxyapatite and collagen, and their mechanical, biological, and degradation properties are analyzed using various experimental and computational techniques, such as attenuated total reflection Fourier-transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, scanning electron microscopy with energy-dispersive X-ray spectroscopy, and molecular simulation. The antimicrobial activity of the nanocomposites is evaluated in vitro against several bacterial and fungal strains, demonstrating their medical potential. Additionally, in silico analyses are performed to predict the absorption, distribution, metabolism, and excretion properties and the bioavailability of the collagen samples. This work opens new avenues for the development of novel biomaterials using cheminformatics tools and methods, which can facilitate the optimization of the design and synthesis parameters, as well as the prediction of the biological outcomes. Future research directions include the investigation of the biocompatibility and bioactivity of the nanocomposites in vivo, as well as the exploration of other applications and functionalities of these nanocomposites.

Recently, there has been a lot of interest in the phenolics of pomegranate peels because of their health-promoting effects. The incorporation of encapsulated phenolic extracts in functional foods, beverages, and dietary supplements can enhance their nutritional and health benefits. This paper aims to provide an overview of the encapsulation of pomegranate peel phenolic extract by co-crystallization, focusing on the properties of the encapsulated extract. Pomegranate peel extract encapsulated in sucrose by co-crystallization at conditions determined in our previous work is characterized by evaluating its properties; moisture content, bulk density, solubility, hygroscopicity, color, degree of encapsulation by thermograms, crystallinity by X-ray scattering, microstructure by scanning electron microscope, and storage stability in terms of total phenolic content and antioxidant activity. The co-crystallized powder had a low moisture content (0.59%) and hygroscopicity (0.011%) and a high bulk density (0.803 g/cm3) and solubility (61 s). Its total phenolic content decreased by only 0.56% after storage at 60oC for 45 days, whereas its antioxidant activity was maintained at levels higher than 84%. The differential scanning calorimetry and the X-ray scattering techniques proved the successful encapsulation in the sucrose matrix and the fact that the extract remained liquid inside the porosity of the sucrose crystals.

This paper presents a bibliometric analysis of highly cited papers published in the journal Sustainability between 2009 and 2023. The aim is to identify influential countries, authors, and papers, as well as patterns in authorship and citation trends. The analysis focuses on frequently cited sources, the most cited research papers and references within the journal, and trends in author keywords. The analysis shows that Sustainability is a leading publication in sustainability research, with an annual growth rate of 53.57%. The selected papers, published between 2013 and 2022, have an average age of 2.11 years and an average of 88.12 citations each. The study highlights the most influential countries in sustainability research published in Sustainability, with China leading, followed by the United States and Germany. The most prolific authors are from China, Spain, and Italy. Interdisciplinary collaboration is essential to address complex sustainability challenges, as shown in the papers published in Sustainability. The study emphasizes the importance of staying informed about emerging trends and research directions in the field of sustainability published in this journal Sustainability. It underscores the significance of fostering international collaborations and partnerships to address complex sustainability challenges facing our world today, as evidenced by the papers published in Sustainability. Overall, this bibliometric analysis provides valuable insights into the current state of sustainability research published in Sustainability and its implications for policy and practice. It highlights key areas for future research and underscores the need for interdisciplinary collaboration to address complex sustainability challenges, as demonstrated by the papers published in Sustainability. These findings have important implications for policymakers, researchers, and practitioners interested in promoting sustainable development in the field of sustainability., as published in Sustainability.

Introduction: Increasing cannabis legalization raises concerns that tobacco use, frequently used with cannabis, will also increase. This study investigated the association between legal status of cannabis in place of residence and prevalence of cannabis and tobacco co-use, simultaneous use, and mixing by comparing the prevalence among adults in Canada (prior to cannabis legalization) vs. adults in US states that had legalized recreational cannabis vs. US states that had not as of September 2018. Methods: Data were drawn from the 2018 International Cannabis Policy Study, conducted with respondents aged 16-65 in Canada and the US recruited from non-probability consumer panels. Differences in the prevalence of co-use, simultaneous use, and mixing between tobacco and different cannabis products were examined using logistic regression models by legal status of place of residence among past 12-month cannabis consumers (N=6744). Results: Co-use and simultaneous use in the past 12 months were most common among respondents in US legal states. Among cannabis consumers, co-use and simultaneous use were less common in US legal states, while mixing was less frequent in US states with both legal and illegal cannabis compared to Canada. Use of edibles was associated with lower odds of all three outcomes, while smoking dried herb or hash was associated with higher odds. Conclusions: The proportion of cannabis consumers who used tobacco was lower in legal jurisdictions despite higher prevalence of cannabis use. Edible use was inversely associated with co-use suggesting that edible use does not appear to be associated with increased tobacco use.

As a typical form of value co-creation, crowdsourcing has been increasingly applied by firms to generate business value. By engaging a crowd, a platform, and other stakeholders, a crowdsourcer can foster the co-creation of a portfolio of value for diverse stakeholders. In analyzing the value co-creation in crowdsourcing, we propose a framework by combining the theories and frameworks in value co-creation and crowdsourcing. The framework examines the key stakeholders, joint purpose, engaged value co-creation processes, contributions, bidirectional relationships of the engagement, and perceived value, exhibiting a holistic view of the value co-creation in a crowdsourcing project. Results of the analysis reveal the business performance of the crowdsourcing project and identify areas of improvement regarding business sustainability. This is a major theoretical contribution of this study. The research design applied a case study approach to empirically investigate a crowdsourcing project. Both the theoretical and practical implications are discussed.

This pot-based study investigated the influence of co-composted wood-derived biochar on lettuce growth performance under salinity and drought stress conditions. Biochar of two particle sizes; > 2 mm and < 1 mm were co-composted with the mixture (1:1 ratio of dry weight) of cow and poultry manures. Co-composted biochars were applied at 5% and 7% rates in soil. Control treatments included the amendment of mixture of biochar with manure in soil. Pots were subjected to slight drought (48-55% water filled pore space (WFPS) of soil) and non-drought conditions (60% WFPS) and under 0 and 1.3 dS m-1 salinity. Results revealed that plants growth performance was significantly better under treatments of co-composted biochar and no salt stress conditions, than when mixture of biochar and manure was applied to soil as non-composted fertilizer. Under no stress condition, small particle-sized co-composted biochar increased root biomass by 786.2% than the large particle-sized co-composted biochar at same application rate. As compared to large-sized co-composted biochar, small sized co-composted biochar at high application rates increased root biomass by 167 – 245% but not leaf biomass under both stress conditions. Small particle-sized co-composted biochar amendment also increased the phosphorus use efficiency (PUE) of lettuce leaves than large particle-sized co-composted biochar under no stress condition. The amendment of small-sized co-composted biochar also increased significantly the concentration of Olsen phosphorus in soil than the amendment of large-particle-sized co-composted biochar. In conclusion, amendment of small particle-sized co-composted biochar has the potential of attenuating salinity and drought stress in lettuce and promoting P cycling in soil.

Applications in high-performance computing (HPC) may not use all available computational resources, leaving some of them underutilized. By co-scheduling, i.e. running more than one application on the same computational node, it is possible to improve resource utilization and overall throughput. Some applications may have conflicting requirements on resources and co-scheduling may cause performance degradation, so it is important to take it into account in scheduling decisions. In this paper, we formalized co-scheduling problem and proposed multiple scheduling strategies to solve it: an optimal strategy, an online strategy and heuristic strategies. These strategies vary in terms of the optimality of the solution they produce and a priori information about the system they require. We showed theoretically that the online strategy provides schedules with a competitive ratio that has a constant upper limit. This allowed us to solve the co-scheduling problem using heuristic strategies that approximate this online strategy. Numerical simulations showed how heuristic strategies compare to the optimal strategy for different input systems. We proposed a method for measuring input parameters of the model in practice and evaluated this method on HPC benchmark applications. We showed high accuracy of measurement method, which allows to apply proposed scheduling strategies in scheduler implementation.

The social distancing as a response to COVID 19 pandemic has led to the exceptional reductions of daily routine people activities and vehicle uses mainly in city. This same situation was also experienced by several busy, large, and populous cities in Southeast Asia (SA) countries. Correspondingly, this study aimed to test the hypothesis that the social distancing implementation period has increased the air quality in the term of carbon monoxide (CO) emission reduction as drawn from Jakarta city as an example of the one of populated cities in SA region. The CO was measured in parts per billions (ppb) and monitored on the daily basis employing remote sensor platform. The monitor periods were started from January, February, March, and April 2020 with 10 measurement days for each month. The social distancing was implemented from mid of March to the recent April. The CO measurement data were statistically tested to justify the significant effects of social distancing on the CO levels. Based on the CO data analysis, the order of CO mean by months is February > January > March > April. The CO levels for January, February, March, and April were 87.46 ppb (95%CI: 83.54-91.37), 88.20 ppb (95%CI: 81.65-94.74), 86.38 (95%CI: 81.06-91.69), and 78.68 (95%CI: 74.03-83.32) respectively. This study also find significant difference (p<0.05) of CO levels especially in April when social distancing has been implemented. Hence, these findings illustrate the potential air pollutant reduction gained from implementing social distancing as can be seen in April.

Degussa P25 is a benchmark form of TiO₂ used worldwide in photocatalysis studies. Currently no such benchmark exists for co-catalysts, which are essential for many photocatalytic reactions. Here, we present the preparation of Pt nanocluster co-catalysts on TiO₂ using an unmodified commercial source and equipment that is commonly available. Transmission electron microscopy reveals that the procedure produces TiO₂ decorated with Pt atom and nanoclusters (1-5 atoms). Optical reflectance and X-ray diffraction measurements show that the procedure does not affect the TiO₂ polymorph or UV-Vis absorbance. Gas phase photocatalytic splitting of heavy water (D₂O) shows that the Pt nanocluster decorated TiO₂ outperforms Pt nanoparticle (produced by photodeposition) decorated TiO₂ in D₂ production. Pt nanoclusters, produced directly from a commercial source, with high co-catalyst activity are prime candidates to be used in benchmark photocatalytic reactions.

In order to understand the effect of Pb-CuI co-doping on the thermoelectric performance of Bi₂Te₃, n-type Bi₂Te₃ co-doped with x at% CuI and 1/2x at% Pb (x = 0, 0.01, 0.03, 0.05, 0.07, and 0.10) were prepared via high temperature solid state reaction and consolidated using spark plasma sintering. Electron and thermal transport properties, i.e., electrical conductivity, carrier concentration, Hall mobility, Seebeck coefficient, and thermal conductivity, of CuI-Pb co-doped Bi₂Te₃ were measured in the temperature range from 300 K to 523 K and compared to corresponding x% of CuI-doped Bi₂Te₃ and undoped Bi₂Te₃. The addition of a small amount of Pb significantly decreased the carrier concentration, which could be attributed to the holes from Pb atoms, thus the CuI-Pb co-doped samples show a lower electrical conductivity and a higher Seebeck coefficient compared to CuI-doped samples with similar x values. The incorporation of Pb into CuI-doped Bi₂Te₃ rarely changed the power factor because of the trade-off relationship between the electrical conductivity and the Seebeck coefficient. The total thermal conductivity(κ_tot) of co-doped samples (κ_tot ~1.4 W/m∙K at 300 K) is slightly lower than that of 1% CuI-doped Bi₂Te₃ (κ_tot~1.5 W/m∙K at 300 K) and undoped Bi₂Te₃ (κ_tot ~1.6 W/m∙K at 300 K) due to the alloy scattering. The 1% CuI-Pb co-doped Bi₂Te₃ sample shows the highest ZT value of 0.96 at 370 K. All data on electrical and thermal transport properties suggest that the thermoelectric properties of Bi₂Te₃ and its operating temperature can be controlled by co-doping.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

The SARS-CoV-2 have caused a devastating pandemic of all times in the recent human history. However, there is a serious paucity in high quality data on aggravating factors and mechanisms of co-infection. This study aimed to identify the trending patterns of bacterial co-infections and types and associated outcomes in three phases of the pandemic. Using quality hospital data, we have investigated the SARS-CoV-2 fatality rates, profiles, and types of bacterial co-infections before, during, and after COVID-19 vaccinations. Out of 389 isolates used in different aspects, 298 was examined before and during the pandemic (n=149 before, n=149 during), death rates were 32% during compared to only 7.4% before pandemic with significant association (P value = 0.000000075). Death rate was 34% in co-infected (n = 170) compared to non-co-infected patients (n = 128) indicating a highly significant value (P value = 0.00000000000088). However, analysis of patients without other respiratory problems (n=28) indicated that among the remaining 270 patients, death was 30% in co-infected patients (n=150) and only 0.8% in non-coinfected (n=120) with high significant P value= 0.00000000076. The trending patterns of co-infections before, during, and after vaccinations showed a significant decline in Staphylococcus aureus with concomitant peaks in Gram-negatives in totals of (n= 149 before/n= 149 during): Klebsiella pneumonia (n = 11/49 before/during; E. coli n=10/24, A. baumannii n=8/25, and Ps. Aeruginosa n= 5/16, and S. aureus 13/1. Nevertheless, in post vaccination phase, (n= 91) gender-specific co-infections were examined for potential differences in susceptibility. Methicillin resistant S. aureus (MRSA) dominated both genders followed by E. coli in males and females with the latter gender showing higher rates of isolations in both species. Klebsiella pneumoniae declined to third place mostly in male patients. The drastic decline in K. pneumoniae and Gram-negatives post-vaccination strongly imply a potential co-protection in vaccines. Future analysis would gain more insights into molecular mimicry.

In this article, we review about the nature of Kerr Blackhole, Kerr metric and express kerr metric in Boyer-Lindquist co-ordinates.

The increase in carbon dioxide emissions has a significant impact on human society and the global environment. As the most abundant and cheap C1 resource, the conversion and utilization of carbon dioxide has received extensive attention from researchers. In many methods of carbon dioxide conversion and utilization, the reverse water gas conversion reaction is considered to be one of the most effective ways. In this paper, the research progress of reverse water gas conversion reaction in recent years is introduced.

Abstract Congenital rubella syndrome is a constellation of birth defects that can have devastating consequences, impacting approximately 100,000 births worldwide each year. The incidence is much lower in countries that routinely vaccinate their population. In the US, postnatal immunization of susceptible women is an important epidemiological strategy for the prevention of rubella. However, concerns that co-administration of Rubella vaccine with other immunoglobins (i.e., Rhogam) could comprise vaccine efficacy has produced warnings that can delay the administration of Rubella vaccination postpartum, leaving women susceptible in a subsequent pregnancy. We aimed to address whether co-administration of Rubella vaccine and Rhogam decreased antibody responses as compared to those receiving only Rubella vaccination. This retrospective cohort study utilized clinical data from 80 subjects who received Rubella vaccine and Rhogam after delivery and 43 subjects received Rubella vaccine alone. Maternal demographics, pregnancy complications and rubella status at the start of a subsequent pregnancy were recorded for analysis. Overall, the two cohorts had similar baseline characteristics; however, lower parity was noted in the participants having both Rubella vaccination and Rhogam. Based on maternal antibody IgG index for rubella during the next pregnancy, we observed that 88% of the Rhogam + Rubella vaccine group had positive titers, which was not significantly different than the 81% in the Rubella vaccine only cohort (p=0.36). In conclusion, no differences in the rubella immunity status in a subsequent pregnancy were observed in those mothers administered both Rubella vaccine and Rhogam concurrently. Given these findings, warnings against co-administration of Rubella vaccine in combination with other immunoglobulins should be discontinued.

Vessel co-option correlates with resistance against anti-angiogenic agents and chemotherapy in colorectal cancer liver metastasis (CRCLM). We previously identified higher intensity of neutrophils in the tumour microenvironment of vessel co-opting CRCLM lesions compared to their angiogenic counterparts. Herein, we demonstrated that over 50% of the neutrophils in vessel co-opting lesions are expressing pro-apoptotic markers including cleaved caspase-3 and poly (ADP-ribose) polymerase-1 (PARP-1). Our previous publications suggested upregulation of transforming growth factor-beta (TGFβ1) in the microenvironment of vessel co-option CRCLM. Therefore, we examined the effect of TGFβ1 on the expression of cleaved caspase-3 and PARP-1 in neutrophils in vitro. Significantly, we noticed the upregulation of pro-apoptotic markers upon exposure to TGFβ1. This finding might pave the way to determine the role of neutrophils in developing vessel co-option in CRCLM in the future.

This study is focused on the mechanical properties of WC-Co composites obtained via Selective Laser Sintering using PA12 as a binder. The as-printed samples were thermally debonded, and sintered, first in vacuum, and then sinter-HIPed at 1400oC, using 50 bar Ar, which has led to relative densities up to 66 %. Optical metallographic images show a microstructure consisting of WC, with an average grain size in the range of 1.4 – 2.0 µm, with isolated large grains, in a well-distributed Co matrix. The shrinkage of the samples was 43 %, with no significant shape distortion. The printing direction of the samples has a great impact on the transversal rupture strength (TRS). Nevertheless, the bending strength was low, with a measured maximum of 612 MPa. SEM images of the fracture surface of TRS samples show the presence of defects that constitute the cause of the low measured values. The hardness values position the obtained composites in the range of medium coarse classical cemented carbides. The results were also related to the amount of free Co after sintering, close to the initial one, as assessed by magnetic measurements, indicating a low degree of interaction with PA12 decomposition products.

Age-related alterations in the gut microbiome composition and its impacts on the host’s health have been well described; however, detailed analyses of the gut microbial structure defining ecological microbe-microbe interactions is limited. One of the ways to determine these interactions is by understanding microbial co-occurrence patterns. We previously showed promising abilities of Lactobacillus acidophilus DDS-1 on the aging gut microbiome and immune system. However, the potential of the DDS-1 strain to modulate microbial co-occurrence patterns is unknown. Hence, we aimed to investigate the ability of L. acidophilus DDS-1 to modulate the fecal, mucosal and cecal-related microbial co-occurrence networks in young and aging C57BL/6J mice. Our Kendall’s tau correlation measures of co-occurrence revealed age-related changes in the gut microbiome, which were characterized by reduced number of nodes and associations across sample types when compared to younger mice. After four-week supplementation, L. acidophilus DDS-1 differentially modulated the overall microbial community structure in fecal and mucosal samples as compared to cecal samples. Beneficial bacteria such as Lactobacillus and Akkermansia acted as connectors in aging networks in response to L. acidophilus DDS-1 supplementation. Our findings provided the first evidence of the DDS-1-induced gut microbial ecological interactions revealing the complex structure of microbial ecosystems with age.

Plastid gene expression involves many post-transcriptional maturation steps resulting in a complex transcriptome composed of multiple isoforms. Although short read RNA-seq has considerably improved our understanding of the molecular mechanisms controlling these processes, it is unable to sequence full-length transcripts. This information is however crucial when it comes to understand the interplay between the various steps of plastid gene expression. Here, the study of the Arabidopsis leaf plastid transcriptome using Nanopore sequencing showed that many splicing and editing events were not independent but co-occurring. For a given transcript, maturation events also appeared to be chronologically ordered with splicing happening after most sites are edited.

Hormones must be balanced and dynamically controlled for the Female Reproductive Tract (FRT) to function correctly during the menstrual cycle, pregnancy, and delivery. Gamete selection and successful transfer to the uterus, where it implants and pregnancy occurs, is supported by the mucosal epithelial lining of the FRT ovaries, uterus, cervix, fallopian tubes, and vagina. Successful implantation and placentation in humans and other animals rely on complex interactions between the embryo and a receptive female reproductive system. The FRT's recent breakthroughs in three-dimensional (3D) organoid systems now provide critical experimental models that match the organ's physiological, functional, and anatomical characteristics in vitro. This article summarizes the current state of the art on organoids generated from various parts of the FRT. The current analysis examines recent developments in the creation of organoid models of reproductive organs, as well as their future directions.

Antibiotic inefficacy in treating bacterial infections is largely studied in the context of developing resistance mechanisms. However, little attention has been paid to combined diseases mechanisms, interspecies pathogenesis and the resulting impact on antimicrobial treatment. This review will consider the co-infections of Salmonella and Schistosoma mansoni. It summarises the protective mechanisms that the pathophysiology of the two infections confer, which leads to an antibiotic protection phenomenon. This review will elucidate the functional characteristics of the gut microbiota in the context of these co-infections, the pathogenicity of these infections in infected mice, and the efficacy of the antibiotics used in treatment of these co-infections over time. Salmonella-Schistosoma interactions and the mechanism for antibiotic protection are not well established. However, antimicrobial drug inefficacy is an existing phenomenon in these co-infections. The treatment of schistosomiasis to ensure the efficacy of antibiotic therapy for bacterial infections should be considered in co-infected patients.

Some emergent SARS-CoV-2 variants raise concerns due to their altered biological properties. For both B.1.1.7 and B.1351 variants, named as variants of concern (VOC), increased transmissibility was reported, whereas B.1.351 was more resistant to multiple monoclonal antibodies (mAbs), as well as convalescent and vaccination sera. To test this hypothesis, we examined the proportion of VOC over time across different geographic areas where the two VOC, B.1.1.7 and B.1.351, co-circulate. Our comparative analysis was based on the number of SARS-CoV-2 sequences on GISAID database. We report that B.1.1.7 dominates over B.1.351 in geographic areas where both variants co-circulate and the B.1.1.7 was the first variant introduced in the population. The only areas where B.1.351 was detected at higher proportion were South Africa and Mayotte in Africa, where this strain was associated with increased community transmission before the detection of B.1.1.7. The dominance of B.1.1.7 over B.1.351 could be important since B.1.351 was more resistant to certain mAbs, as well as heterologous convalescent and vaccination sera, thus suggesting that it may be transmitted more effectively in people with pre-existing immunity to other VOC. This scenario would lessen the effectiveness of vaccine and urge the need to update them with new strains.

Long non-coding RNA (lncRNA) can regulate several aspects of gene expression, being associated with complex phenotypes in humans and livestock species. In taurine beef cattle, recent evidence points to the involvement of lncRNA in feed efficiency (FE), a proxy for increased productivity and sustainability. Here, we hypothesized specific regulatory roles of lncRNA in FE of indicine cattle. Using RNA-Seq data from liver, muscle, hypothalamus, pituitary and adrenal gland from Nellore bulls with divergent FE, we submitted new transcripts to a series of filters to confidently predict lncRNA. Then, we identified lncRNA that were differentially expressed (DE) and/or key regulators of FE. Finally, we explored lncRNA genomic location and interactions with miRNA and mRNA to infer potential function. We were able to identify 126 relevant lncRNA for FE in Bos indicus, some with high homology to previously identified lncRNA in Bos taurus and some possible specific regulators of FE in indicine cattle. Moreover, lncRNA identified here were linked to previously described mechanisms related to FE in hypothalamus-pituitary-adrenal axis and are expected to help elucidate this complex phenotype. This study contributes to expanding the catalogue of lncRNA, particularly in indicine cattle, and identifies candidates for further studies in animal selection and management.

Background: On late December 2019, a viral pneumonia known as coronavirus disease 2019 (COVID-19), was originated from China and spread very rapidly in the world. Therefore, COVID-19 became a global concern and health problem. Methods: We presented four patients in this study. They were selected from patients who presented with pneumonia symptoms and were suspicious for COVID-19 and referred to the intended centers for COVID-19 diagnosis and management of Shiraz University of Medical Sciences in the south of Iran. Two nasopharyngeal and oropharyngeal throat swab samples were collected from each patient and tested for severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) detection by real-time reverse-transcriptase–polymerase-chain-reaction (RT-PCR), and also samples were sent for influenza viruses and all the respiratory panel. Results: In the present report, four patients were diagnosed in the starting days of COVID-19 disease in our center in south of Iran with co-infection of SARS-CoV-2 and influenza virus. Conclusions: This co-infection of COVID-19 and influenza highlights the importance of considering SARS-CoV-2 PCR assay regardless of other positive findings for other pathogens in the primary test during the epidemic.

Contact-based co-culture of fibroblasts and keratinocytes is important to study the structure and functions of the wound bed. Co-culture of these two cell types in direct contact with each other has been challenging, requiring high serum concentrations (up to 10%), feeder systems and a range of supplemental factors. These approaches are not only technically demanding, but also present scientific, cost and ethical limitations associated with high-serum concentrations. We have developed two reduced-serum approaches (1-2%) to support contact-based co-culture of human dermal fibroblasts (HDFa) and human epidermal keratinocytes (HaCaT). The two approaches include (1) Specialized cell culture media for each cell type mixed in a 1:1 ratio (KGM+FGM), and (2) Minimal media supplemented with cell-specific growth factors (MEM+GF). Co-culture could be successfully achieved by co-seeding (two cell types were introduced simultaneously), or in a layered fashion (keratinocytes seeded on top of confluent fibroblasts). With wound scratch assays, the co-cultured platforms could demonstrate cell proliferation, migration and wound closure. The reduced-serum conditions developed are simple, easy to formulate and adopt, and based on commonly-available media components. These contact-based co-culture approaches can be leveraged for wound and skin studies, and tissue bioengineering applications, potentially reducing concerns with high-serum formulations.

Background: The febrile patient from tropical areas, in which emerging arboviruses are endemic, represent a diagnostic challenge and potential co-infections with other pathogens (i.e bacteria or parasites) are usually overlooked. Objectives: We present a case of an elderly woman diagnosed with dengue, chikungunya and Leptospira interrogans co-infection. Study Design: Case report. Results: An 87-year old woman from Colombia complained of upper abdominal pain, arthralgia, myalgia, hyporexia, malaise and intermittent fever accompanied with progressive jaundice. She had a medical history of chronic heart failure (Stage C, NYHA III), without documented cardiac murmurs, right bundle branch block, non-valvular atrial fibrillation, hypertension, and chronic venous disease. Her cardiac and pulmonary status quickly deteriorated after 24 hours of her admission without electrocardiographic changes and she required ventilatory and vasopressor support. In the next hours the patient evolved to pulseless electrical activity and then she died. Dengue IgM, NS1 ELISA, MAT for Leptospira interrogans and RT-PCR for chikungunya, were positive. Discussion: This case illustrates a multiple co-infection in a febrile patient from a tropical area of Latin America that evolved to death.

In this work, we report synthesis of Cu, Pt and Pd doped SnO₂ powders and their comparative CO gas sensing studies. Dopants were incorporated into SnO₂ nanostructures using chemical and impregnation methods by using urea and ammonia as precipitation agents. The synthesized samples were characterized using X-ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM) and High resolution transmission electron microscopy (HR-TEM). The presence of dopants within the SnO₂ nanostructures was evidenced from HR-TEM. Doped powders utilizing chemical methods with urea as precipitation agent presented higher sensitivities compared to the remaining, which is due to the formation of uniform and homogeneous particles resulted from the temperature assisted synthesis. The particle sizes of doped SnO₂ nanostructures were in the range of 40-100 nm. An enhanced sensitivity around 1783 was achieved with Cu doped SnO₂ when compared with two other dopants i.e., Pt (1200) and Pd: SnO₂(502). The high sensitivity of Cu: SnO₂ is due to formation of CuO and its excellent association and dissociation in the presence of CO with adsorbed atmospheric oxygen at sensor operation temperatures resulted in high conductance. Cu: SnO₂ may be an alternative and cost effective sensor for industrial applications.

Good governance in natural resource management (NRM) is one of the most challenging issues in developing countries that often inappropriately embedded in national policies and political agendas. It is, in fact, even more important for countries like Bangladesh with exceptionally high pressure and dependence on its natural resources for sustaining rural livelihoods. Globally, nowadays, good governance is considered as one of the key factor for achieving the goal of sustainable development and biodiversity conservation. Bangladesh, of late has responded to that global zeal by involving local communities in the management of country’s declining forest and other natural resources. The colonial legacy of the forestry sector of Bangladesh was planned and, managed as interim projects through donors’ prescriptions. Thus, institutions, management processes and conservation outcomes were problematic. The conventional approach adopted by colonial and post-colonial regimes for forest management also proved to be inefficient due to its top-down management system. The absolute dependency on donor support, and their prescription sometimes worsened the situation both ecologically and socially. Global, regional and local trends supported the need for a different dimension in the governance paradigms. The introduction of a pluralistic approach, known as co-management in protected areas (PAs) is an example of an attempt whereby shared governance mechanism are implemented to attain the desired goals of conservation that will also address the livelihoods and aspirations of communities living in and around PAs of the country. However, in designing future forest and PA regimes the concern of the external aid support and attached conditions remain a reality that needs to be addressed. Adequate attention should be given to our vanishing biodiversity, culture and community livelihoods through devising an appropriate governance mechanism recognizing and supporting local rights, access and participation in the environmental management. It is now time to mainstream the adhoc nature of governance according to our national conservation strategy and policy frameworks in order to achieve the goals and objectives of the Bangladesh NRM sector addressing the human and community right of people in the specific context of forest protected areas management.

Despite of being an exceptionally biodiversity rich country, the forest coverage of Bangladesh is declining at an alarming rate. Declaration and management of protected areas in this regard is one of the efforts from government side to tackle the loss of biodiversity. The limited numbers of forest-protected areas (FPA), established to conserve the dwindling forest biodiversity of the country with high pressure on them for timber, non-timber forest products, and fuelwood - makes their management challenging. Moreover, most of the FPAs of the country declared only in the recent decades with very limited infrastructure, manpower and policy support for monitoring and governance. Some people-centred approaches for the management of FPAs and alternative livelihood and income generation subsidies although made available through a few project interventions, their number are still inadequate and performance remains less than satisfactory. This chapter provides a critical review of the FPAs of Bangladesh looking at their role in biodiversity conservation, management challenges, and key lessons from previous management interventions with recommendations for the future. It has been revealed that the FPA system of Bangladesh still poorly represents the diverse forest ecosystems with relatively small forest size and lack of corridors for the movement of wildlife. There are ample opportunities to render co-management of FPAs an effective strategy to minimize the conflicts in FPAs management in the country. It is, however, important to ensure the access of local forest-dependent people to different alternative income generating options that may adequately support their livelihoods.

In 2023, the technological landscape witnessed an unprecedented surge of transformative innovations, including Web 3.0 and machine learning, poised to revolutionize various aspects of our daily lives. At the forefront of this revolution stands artificial intelligence (AI), which has evolved from a concept once confined to science fiction into an indispensable force reshaping industries on a global scale. Notably, recent years have seen remarkable strides in AI functionalities, particularly in machine learning, computer vision, and natural language processing. These advancements have empowered AI to generate diverse interactions and media autonomously. This study ultimately provides invaluable insights into the dynamic intersection of AI and Advertising, con-tributing to a deeper comprehension of this evolving field. This study conducts a comprehensive review of Artificial Intelligence within the advertising domain, employing network analysis. By meticulously examining the evolution of AI through co-occurrences of terms, keywords, and co-authorship analysis, we aim to unveil the relationship of AI & Advertising through the lens of Generative models to identify pivotal trends, core concepts, and seminal studies that have profoundly influenced the industry. The analysis charts the trajectory leading to the emergence of Generative Artificial Intelligence (GenAI), a transformative development poised to revolutionize advertising practices and consumer engagement. In tandem with these objectives, the results highlight vital trends, emphasizing the growing prominence machine learning tools and techniques such as deep learning techniques and advanced natural language processing methods like word2vec, GANs, and more in shaping the future of advertising practices.

Herein, we report on a versatile system composed of two Ni(II)-based coordination compounds: a 3D metal-organic framework of {[Ni(μ-3isoani)2]·DMF}n (1) formula and a 0D monomeric [Ni(3isoani)2(H2O)4] (2) complex (where 3isoani = 3-aminoisonicotinato and DMF = dimethylformamide) which show mutual solvent-induced reversible transformations into each other. These 1 ↔ 2 transformations are triggered by the exposure of one compound to the solvent present in the other, that is, the MOF (1) in water and the monomer (2) in DMF. The process is easily followed by the naked eye because it involves a colour change from green (1)-to-brownish green (2), making the system potentially interesting to act as a sensor of those solvents. Moreover, these compounds present very different magnetic properties since 1 shows field-induced single-molecule magnet (SMM) behaviour, which corresponds to one of the few Ni(II)-based compounds showing this property, whereas 2 behaves as a regular paramagnet, all of which is explained according to a careful study of the magnetic properties by means of experimental direct-current (dc) and alternating-current (ac) measurements as well as complete active space self-consistent field (CASSCF) calculations.

The COVID-19 pandemic remains a serious public health problem globally. During winter flu seasons, more aggressive SARS-CoV-2 infections with fatalities have been documented, indicating that influenza co-infections may significantly impact the disease outcome of COVID-19. Both influenza and SARS-CoV-2 viruses share many similarities in their transmission and cellular tropism for their replication in the human respiratory tract. However, it is still unclear how the two pathogens interplay to ensure their survival in the same lung microenvironment. In addition, clinical studies on influenza co-infections in COVID-19 patients do not provide conclusive evidence on how influenza co-infection mechanistically modifies the disease outcome in COVID-19. This mini-review discusses various viral as well as host factors that potentially influence the survival or synergism of these two respiratory pathogens in the infected lung microenvironment.

Objective: The study aimed to characterize the changing landscape of circulating SARS-CoV-2 lineages in the local community of Hong Kong throughout 2022. We examined how adjustments to quarantine arrangements influenced the transmission pattern of Omicron variants in a city with relatively rigorous social distancing measures at that time. Methods: In 2022, a total of 4,684 local SARS-CoV-2 genomes were sequenced using the Oxford Nanopore GridION sequencer. SARS-CoV-2 consensus genomes were generated by MAFFT, and the maximum likelihood phylogeny of these genomes were determined using IQ-TREE. The dynamic changes in lineages were depicted in a time tree created by Nextstrain. Statistical analysis was conducted to assess the correlation between changes in the number of lineages and adjustments to quarantine arrangements. Results: By the end of 2022, a total of 83 SARS-CoV-2 lineages were identified in the community. The increase in the number of new lineages was significantly associated with the relaxation of quarantine arrangements (One-way ANOVA, F(5,47)=18.233, p&lt;0.001)). Over time, Omicron BA.5 sub-lineages replaced BA.2.2 and became the predominant Omicron variants in Hong Kong. The influx of new lineages reshaped the dynamics of Omicron variants in the community without fluctuating the death rate and hospitalization rate (One-way ANOVA, F(5,47)=2.037, p=0.091). Conclusion: The study revealed that even with an extended mandatory quarantine period for incoming travelers, it may not be feasible to completely prevent the introduction and subsequent community spread of highly contagious Omicron variants. Ongoing molecular surveillance of COVID-19 remains essential to monitor the emergence of new recombinant variants.

This study explores how young people’s mental health was affected by the COVID-19 pandemic using artwork and semi-structured interviews. This is important to understand so that policy and practice professionals can support those affected, prepare, and respond to future crises, and support young people who are isolated and restricted in other contexts. Co-designed participatory art workshops and interviews were conducted with 16–18-year-olds (N = 21) from the London-based Longitudinal cohort Study of Cognition, Adolescents and Mobile Phones (SCAMP). Artworks and interview transcripts were qualitatively co-analysed with young people. From interviews, six themes were identified: adaptation, restriction, change, challenges, overcoming adversity, and lockdown life. From artwork, four themes were identified; trapped, negative mental wellbeing, positive emotions, and technology. Everyday factors such as home environment, relationships, hobbies, habits, and education or work were key determinants of how challenged and restricted participants felt, and their capacity to overcome this. This implies that young people’s mental health services should collaborate with other sectors to address wider life determinants in a holistic way, and that clearer guidance and support in these areas could mitigate the negative mental health impacts of major environmental changes on young people.

Combustion power plants emit carbon dioxide (CO₂), a major contributor to climate change. Direct emissions measurement is cost-prohibitive globally, while reporting varies in detail, recency, and granularity. To fill this gap and greatly increase the number of power plants worldwide with independent emissions monitoring, we developed and applied machine learning (ML) models using power plant plumes as proxy signals to estimate electric power generation and CO₂ emissions using Landsat 8, Sentinel-2, and PlanetScope imagery. Our ML models estimated power plant activity on each image snapshot, and then an aggregation model predicted plant utilization over a 30-day period. Lastly, emissions factors specific to region, fuel, and plant technology were used to convert estimated electricity generation to CO₂ emissions. Models were trained with reported hourly generation data in the US, Europe, and Australia and were validated with additional generation and emissions data from the US, Europe, Australia, Türkiye, and India. All results with sufficiently large sample sizes indicate that our models outperformed baseline approaches. In conducting external validation to compare modeled versus reported annual generation and emissions in the countries where available, we calculated the root mean square error overall for modeled countries with validation data as respectively 1.75 TWh (236 plants across 17 countries over 4 years) and 2.04 Mt CO₂ (207 plants across 17 countries over 4 years). Ultimately, we applied our ML method to plants that comprise 32% of global power plant CO₂ emissions averaged over 2015-2022. This dataset is the most comprehensive independent and free-of-cost global power plant point-source emissions monitoring system currently known to the authors and is publicly available at climatetrace.org to support global emissions reduction.