Permafrost covers about 23% ~ 25% of the land in the northern hemisphere, mainly in Russia, Canada, Alaska, Northeast and Qinghai Tibet Plateau (QTP) in China. Many engineering especially the transportation has been in the permafrost regions above. Under the action of highways construction and global warming, permafrost under infrastructures is degraded and causes serious damage. Two phases closed thermosyphon (TPCT) is a widely accepted green countermeasure against the problem in permafrost regions. Although it has been applied to prevent permafrost degradation, their application presents significant challenges on account of the stronger endothermic action of asphalt pavement. This paper focused on the thermosyphon technology and application in the permafrost. Moreover, the article highlighted the excellent working performance of the TPCT that improving the stability of the infrastructures and prevent it degrading due its excellent efficiency of heat transfer. The industrial applications of the TPCT were also summarized, along with their limitations. Finally, the results reported in this paper can provide a valuable guidance for the design of the TPCT and construction of the permafrost regions in the future.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

Accurate diagnosis for the 400 million people with rare diseases is critical for healthcare decisions, prognosis, understanding disease mechanisms, and identification of treatments. Despite advances in genome sequencing, barriers such as high interpretation costs, diagnostic expertise, throughput associated delays, and uncertain variant classifications persist, with demand exceeding capacity. Many variant classification methods focus narrowly on specific consequences, leading to the use of complex integrative pipelines that often overlook transcript variability and lack prediction transparency. To overcome these limitations, we introduce DITTO. This transparent, transcript-aware machine-learning method demonstrates superior overall performance in accuracy, recall, and precision when compared to existing tools. DITTO is publicly available at https://github.com/uab-cgds-worthey/DITTO

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

This research presents a comprehensive computational analysis of the two-phase flow dynamics within a three-dimensional porous transport layer (PTL) in a proton exchange membrane (PEM) electrolyzer. Employing advanced computational fluid dynamics (CFD) and a volume of fluid (VOF) approach, the study utilizes the finite-volume method to model a time-dependent, isothermal process within a laminar flow regime. Notably, the study treats oxygen as the dispersed phase and water as the continuous phase within the system. Investigations on the anode side uncovered the formation of gas bubbles on the electrode's surface subsequent to the electrochemical reaction. The simulation, spanning 5 seconds with 0.25-second intervals, highlights the critical role of the time interval between the initiation and 2 seconds in achieving pressure and velocity equilibrium within the PTL. The initial 0.75 seconds witnessed a peak in oxygen concentration, followed by its movement across the PTL, exhibiting a transition from regions of lower to higher concentration, consistent with known physical behaviour. Remarkably, the model recorded the highest pressure of 3.5 Pa at 0.25 s. Furthermore, the study observed an incremental pressure drop from 0.25 s to 0.5 s and 1 s, approximately amounting to 28.5% and 20%, respectively, ultimately leading to a uniform pressure distribution within the model. Over time, the pressure drop intensified across the entire model due to the evolving nature of the oxygen gas. These findings provide valuable insights into the complex dynamics of two-phase flow processes within PEM electrolyzers, contributing to the advancement of sustainable energy technologies.

An experimental investigation on the heat pump performance improvement equipped with the two-phase ejector called “an ejector-expansion heat pump (EEHP)” is proposed. The system performance of the EEHP is compared with a vapour-compression heat pump (VCHP). The improvement potential is determined and discussed. The heat pump test system is constructed which is based on a water-to-water heat pump. It can be experimented with both EEHP and VCHP. The two-phase ejector with the cooling load up to 2500 W is installed for experiment. The results show that the EEHP always produces a higher heating rate and COP than the VCHP throughout the specified working conditions. The heating COP is increased by 5.7-12.2% depending on the working conditions. It is also that under the same heat sink and heat source temperature, the EEHP can produce lower compressor discharge temperature and lower compressor pressure ratio than the VCHP. This is evidence that the two-phase ejector can provide better compressor working characteristics which yields a longer compressor lifetime. It is demonstrated that a key to the performance of the EEHP is the expansion pressure ratio. A larger expansion pressure ratio yields a higher improvement potential when compared with the VCHP.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

The characterization of thin-film solar cells is of huge importance for obtaining high open-circuit voltage and low recombination rates from the interfaces or within the bulk of the main materials. Among the many electrical characterization techniques, the two- and four-wire probe using the Cascade instrument is of interest since the resistance of the wires, and the electrical contacts can be excluded by the additional two wires in 4-wire probe configuration. In this paper, both two and four-point probes configuration are employed to characterize the CIGS chalcogenide thin-film solar cells. The two-wire probe has been used to measure the current-voltage characteristics of the cell which results in a huge internal resistance. Therefore, the four-wire connection is also used to eliminate the lead resistance to enhance the characterization’s accuracy. The load resistance in the two-wire probe diminishes the photogenerated current density at smaller voltage ranges. In contrast, the proposed four-wire probe collects more current at higher voltages due to enhanced carrier collection efficiency from contact electrodes. The current conduction mechanism is also identified at every voltage region represented by the value of the ideality factor of that voltage region. It is observed that a long time given to the charge collection results in increased current density at a higher voltage. According to the results and device characteristics, a novel double-diode model is suggested to extract the saturation current density, shunt and series resistances and the ideality factor of the cells. These cells are shown to be efficient in terms of low recombination at the interfaces and with lower series resistance as the quality of the materials is in its most possible conductive form. The measured internal resistance and saturation current density and ideality factor of the two measurement configuration is measured and compared.

Background: Autonomic balance measurement (ABM) is a valuable tool in clinical practice for assessing the functioning of the autonomic nervous system (ANS), which controls involuntary bodily functions. Here we summarize the current understanding of the utility of autonomic balance measurement in clinical practice. Methods: A narrative review of relevant literature was conducted, focusing on studies investigating the use of autonomic balance measures in various clinical settings. Results: ABM holds potential benefits in clinical practice, including aiding in diagnosing autonomic dysfunction, monitoring treatment efficacy, and predicting potential health complications. ABM can be crucial for diagnosing various conditions, including cardiovascular diseases (Heart failure, arrhythmias, and hypertension), neurological disorders (Parkinson's disease, Alzheimer's disease, and diabetic neuropathy), in sports medicine athletes can undergo ABM to optimize training regimens, enhance performance, assessing the impact of training stress, preventing overtraining, and promoting overall well-being and probably to assess potential health risks, in metabolic syndromes ABM can aid in the early detection of autonomic neuropathy, a diabetes-related complication, allowing for timely intervention and better management of the disease, and psychiatric disorders (Anxiety, depression, and post-traumatic stress disorder). In addition, ABM can be helpful in monitoring of treatment efficacy, by tracking changes in autonomic balance, clinicians can assess if treatments for conditions impacting the autonomic nervous system are effective. ABM can also be helpful in predicting outcomes by facilitating early recognition of future health complications in certain populations. However, limitations exist, including non-specificity, variability in measurements, and limited evidence for routine use in specific clinical settings. Conclusion: Incorporating autonomic balance measurement into routine clinical assessments provides a more comprehensive understanding of a patient's health. It complements traditional diagnostic methods, offering additional insights into the body's regulatory mechanisms. While autonomic balance measurement offers potential benefits, careful interpretation and consideration of its limitations are crucial for its effective use in clinical practice. ABM remains a valuable and versatile tool in clinical practice for a deeper understanding of the autonomic nervous system, enabling early detection, targeted interventions, and improved management of various medical conditions across different specialties.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

The unsteady flow around the monopile under the influence of wave and vibration is studied by numerical method. Based on VOF model and SST Turbulence model, combined with Intermittent Transition model and dynamic mesh method, wave generation and pile vibration in numerical flume are simulated. The flow field around vibrating monopile in a calm water flume and a wave flume is simulated and the simulation results are compared. The calculation results show that the monopile vibration has a great disturbance to the unsteady flow around the pile, and the disturbance degree intensifies with the increase of the vibration amplitude of the monopile: Under the action of inertia, the vibration of the monopile leads to the reattachment of the shedding vortices; Under the influence of the reattachment vortices, the asymmetry of the vorticity on the side wall of the monopile intensifies; The intensification of the disturbance causes the reduction of the phase lead angle of the bed shear stress on the side of the single pile, and an additional high bed shear stress appears on the side of the monopile. In addition, the vortex structure formed alternately around the monopile during the vibration process leads to the periodic change of the high bed shear stress.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

This paper presents a new scientific contribution on the two-dimensional (2-D) subdomain technique in polar coordinates taking into account the finite relative permeability of the ferromagnetic material. The constant relative permeability corresponds to linear part of the nonlinear B(H) curve. As in conventional technique, the method of separation of variables and the Fourier’s series are used for the resolution of magnetostatic Maxwell’s equations in each region. Although, the general solutions of magnetic field in the subdomains and boundary conditions (BCs) between regions are different in the conventional and proposed method. In this later, the magnetic field solution in each subdomain is a superposition of two magnetic quantities in the two directions (i.e., r- and Q-axis) and the BCs between two regions are also in both directions. For example, the scientific contribution has been applied to an air- or iron-cored coil supplied by a constant current. The distribution of local quantities (i.e., the magnetic vector potential and flux density) has been validated by a corresponding 2-D finite-element analysis (FEA). The obtained semi-analytical results are in very good agreement with those of numerical method.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

The research community has shown significant interest in the aqueous synthesis of nanomaterials due to its ability to eliminate the need for complex organic solvents. This synthesis approach aligns with the principles of green chemistry, attracting considerable attention. Aqueous solution technology in fabricating nanostructures has gained recognition for its potential to create ultrasensitive, low-energy, and ultrafast optoelectronic devices. This report focuses on synthesizing lead iodide (PbI2) nanoplates using a water-based solution technique and fabricating a planar photodetector. The photodetectors with a planar type of device structure (ITO/PbI2 NPs/Au) demonstrated a remarkable photosensitivity of 3.9×103 and a photoresponsivity of 0.51 mA/W at a wavelength of 405 nm. Notably, the asymmetrical output properties of ITO/PbI2 NPs/Au detector deliver additional evidence of the effective creation of a Schottky contact. Thus, the photodetector exhibited a photoresponse even at 0 V bias, leading to the realization of self-powered photodetectors. Additionally, the device exhibited a rapid photoresponse of 0.21/0.38 s (−5 V) in the visible range. This study has expanded the horizons for the aqueous-phase synthesis of nanoplate nanostructures, enabling the large-area fabrication of high-performance photodetectors.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Selection of appropriate friction factors is paramount for accurate prediction of key flow characteristics in gas–liquid two-phase flows. In this work, experimental investigation of vertical air and oil (with viscosities up to 200 mPa s) flow in a 0.060-m ID pipe is reported. Superficial air and oil velocity ranges utilized are from 22.37 to 59.06 m/s and 0.05 to 0.16 m/s respectively. The influence of estimation of interfacial friction factor on accurate determination of film thickness, void fraction and pressure gradient was investigated using a two-fluid model. The results indicated that the two-fluid model is capable of accurately predicting flow characteristics. Further, it reveals that the best performing correlations are the Belt et al. and Ambrosini et al. correlations.

The goal of this paper is to propose a dual version of the direct cosine simplex algorithm (DDCA) for general linear problems. Unlike the two-phase and the big-M methods, our technique does not involve artificial variables. Our technique solves the dual Klee-Minty problem in two iterations and solves the dual Clausen’s problem in four iterations. The utility of the proposed method is evident from the extensive computational results on test problems adapted from NETLIB. Preliminary results indicate that this dual direct cosine simplex algorithm (DDCA) reduces the number of iterations of two-phase method.

A new formulation for a proposed solution to the 3D Navier-Stokes Equations in cylindrical co-ordinates coupled to the continuity and level set convection equation is presented in terms of an additive solution of the three principle directions in the radial, azimuthal and z directions of flow and a connection between the level set function and composite velocity vector for the additive solution is shown. For the case of a vertical tube configuration with small inclination angle, results are obtained for the level set function defining the interface in both the radial and azimuthal directions. It is found that the curvature dependent part of the problem alone induces sinusoidal azimuthal interfacial waves wheras when the curvature together with the equation for the composite velocity is considered oscillating radial interfacial waves occur. The implications of two extremes indicate the importance of looking at the full equations including curvature.

Well-exposed fluvio-deltaic Surma Group successions of the northeastern Surma Basin provide a direct analogue to its equivalent subsurface successions—the main hydrocarbon reservoirs in Bangladesh. The various levels of lateral and vertical heterogeneities lead to changes in the subsurface sandbody distributions and their reservoir qualities across fields. The present study aims to identify the heterogeneities in the fluvio-deltaic Surma Group successions by detailed sedimentological analysis of the Mio-Pliocene-aged Surma Group successions. Eleven lithofacies have been identified and based on the recurring pattern of these facies within the Surma Group, five facies associations have been identified. The facies associations indicate that these deposits originated from diverse depositional settings, ranging from the prodelta to the alluvial to delta plain. As a whole, they represent a progressive shallowing upward succession with two transgressive events in the upper and lower parts of the Surma Group. Five levels of heterogeneities such as prodelta mud (HL-I), tidal heterolithic deposits (HL-II & III), interbedded mud units in delta front (HL-IV), and intercalated mud laminae, drapes (HL-V) have been identified in the fluvio-deltaic Surma Group. The study suggests that the various levels of reservoir heterogeneities are controlled by the occurrence and distribution of various facies associations.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

This study focuses on examining various approaches for Tensor Decompositions (TDs) and their potential applications in satellite imaging (SI) and deep learning (DL). The research highlights how these decompositions can contribute to the advancement of SI and DL, providing valuable insights for future utilization of TDs in research. It explores how these techniques contribute to the advancement of SI and DL methods, providing insights into their potential applications and suggesting future research directions. The study aims to enhance the use of TDs techniques to further advance research efforts in these fields. More importantly, the current investigation offers a thorough analysis of the potential advantages and reasons for employing TDs techniques in different domains, including satellite imaging and deep learning. The aim is to enhance research outcomes by utilizing TDs. The review also identifies unresolved issues and proposes future directions for further investigation in this field. Fundamentally, these proposed open problems will open new grounds to the research community to articulate, innovate, and provide more real-life applications to improve the current state of the art by delving into a wider vision for a higher-level performance of both satellite imaging (SI) and deep learning (DL). Looking at the bigger scenario, this also suggests that TDs could be potentially employed to revolutionize existing machine learning technologies as well as the current space AI industry.

Actually, the study aimed to manage and to analyse the results of the laboratory methods, using liver samples, preparing and analizing in pathology service. This mentioned, are known as routinally practice for hepatitis C diagnosis, which conduct to hepatic cirrhosis. In this study direction, chronic liver diseases stimulate a degree of hepatocyte injury. So previously mentioned modifications, alters thet affect the liver architecture and finally ends in cirrhosis are well analyse on microscopic preparates. Folowing morphological steps, it is possible to analyse normal and alterate liver structure, on colored preparates.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

Two-dimensional mass spectrometry (2D MS) is a method for tandem mass spectrometry that relies on manipulating ion motions to correlate precursor and fragment ion signals. 2D mass spectra are obtained by performing a Fourier transform in both the precursor ion mass-to-charge ratio (m/z) dimension and the fragment ion m/z dimension. The phase of the ion signals evolves linearly in the precursor m/z dimension and quadratically in the fragment m/z dimension. This study demonstrates that phase-corrected absorption mode 2D mass spectrometry improves signal-to-noise ratios by a factor of 2 and resolving power by a factor of 2 in each dimension compared to magnitude mode. Furthermore, phase correction leads to an easier differentiation between ion signals and artefacts, and therefore easier data interpretation.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

The global textile sector, pivotal to economic development, significantly contributes to environmental degradation, prompting a shift towards sustainable raw material sources. Embracing circular economy principles, this industry is exploring the valorization of agricultural by-products. This study introduces an innovative approach to repurposing mango waste into valuable textile fibers, a byproduct of the fruit processing industry, predominantly generated during juice and jam production. The focus is on the lignocellulosic constituents of mango waste, specifically the peel, seed, and fibrous material, traditionally considered as refuse. Previous research has predominantly utilized mango peel in pectin extraction for food applications, whereas the potential of seed and fibrous content remains underexplored. This investigation endeavors to transform these fibrous by-products into high-value materials suitable for textile manufacturing. The process involved washing, drying, and comprehensive physicochemical characterization of mango fibers, emphasizing lignin quantification, revealing a composition of 12.2% lignin. An experimental design was employed to elucidate the impact of variables such as liquid-to-solid ratio, reaction duration, and sodium hydroxide concentration on lignin dissolution through alkaline hydrolysis. Optimal conditions—10% NaOH concentration, 30 mL/g liquid-to-solid ratio over six hours—achieved an 83% reduction in lignin content. The resulting fibers exhibited properties akin to conventional natural fibers, including a favorable aspect ratio indicative of their suitability for textile applications. A subsequent softening process using propylene glycol enhanced the fibers' spinability, producing a durable, textured fabric ideal for eco-conscious fashion applications, including bags, footwear, and accessories. This research demonstrates the feasibility of converting mango waste into a textile-worthy material and underscores the importance of waste revalorization in promoting sustainability within the circular economy framework.

This study explored what motivates university counselors. By analyzing various factors like personal values and work environment, they found counselors experience greater career satisfaction when their work aligns with their own values and societal impact, and when they receive recognition and opportunities for growth. Universities can utilize these findings to create a more supportive environment for counselors by highlighting their impact, offering development opportunities, and fostering a positive work culture. This can ultimately lead to a more motivated and effective counseling team, benefiting both the counselors and the students they serve.

The Double Random Phase Encoding (DRPE) image encryption method has garnered significant attention in color image processing and optical encryption, thanks to its parallel encryption of R, G, B. However, DRPE-based color image encryption faces two challenges. Firstly, it disregards the correlation of R, G, and B, compromising the encrypted image's robustness. Secondly, DRPE schemes relying on Discrete Fourier Transform (DFT) and Discrete Fractional Fourier Transform (DFRFT) are vulnerable to linear attacks, such as Known Plaintext Attack (KPA) and Chosen Plaintext Attack (CPA). Quantum walk stands out as a remarkable tool for designing modern cryptographic mechanisms, offering resistance to potential attacks from both classical and quantum computers.Therefore, this study presents an optical color image encryption algorithm that combines two-dimensional quantum walk with 24-bit plane permutation, dubbed OCT. This approach employs pseudo-random numbers generated by Two-Dimensional Quantum Walking (TDQW) for phase modulation in DRPE and scrambles the encrypted image's real and imaginary parts using the Generalized Arnold Transform. The 24-bit plane permutation helps reduce correlation of the R, G, B, while the Generalized Arnold Transform bolsters DRPE's resistance to linear attacks. By incorporating TDQW, the key space is significantly expanded. Experimental results validate the effectiveness and security of proposed method.

This paper studied the nonlinear vibrations of top tensioned cantilevered pipes conveying pressurized steady two-phase flow under thermal loading. The coupled axial and transverse governing partial differential equations of motion of the system were derived based on Hamilton’s mechanics with the centreline assumed to be extensible. Multiple scale perturbation method was used to resolve the governing equations, which resulted to an analytical approach for assessing the natural frequency, mode shape and the nonlinear coupled axial and transverse steady state response of the pipe. The analytical assessment reveals that at some frequencies the system is uncoupled, while at some frequencies a 1:2 coupling exists between the axial and the transverse frequencies of the pipe. Nonlinear frequencies versus the amplitude displacement of the cantilever pipe conveying two-phase flow at super critical mixture velocity for the uncoupled scenario exhibit a nonlinear hardening behaviour, an increment in the void fractions of the two-phase flow resulted to a reduction in the pipe’s transverse vibration frequencies and the coupled amplitude of the system. However, increasing the temperature difference, pressure and the presence of top tension were observed to increase the pipe’s transverse vibration frequencies without a significant change in the coupled amplitude of the system.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

Triple-negative breast cancer (TNBC), lacking specific receptors found in other breast cancer subtypes, poses significant treatment challenges due to limited therapeutic options. Therefore, it is necessary to develop novel treatment approaches for TNBC. In the last few decades, many attempts have been reported for alternative tools for TNBC treatment: immunotherapy, radiotherapy, targeted therapy, combination therapy, and nanotechnology-based therapy. Among them, combination therapy and nanotechnology-based therapy show the most promise for TNBC treatment. This review outlines recent advancements in these areas, highlighting the efficacy of combination therapy (immunotherapy paired with chemotherapy, targeted therapy, or radiotherapy) in both preclinical and clinical stages and nanotechnology-based therapies utilizing various nanoparticles loaded with anticancer agents, nucleic acids, immunotherapeutics, or CRISPRs in preclinical stages for TNBC treatment.

ABSTRACTIntroduction and Purpose: Nurses are expected to be competent in practice based on the domain of standards and interpersonal soft skills (ISS). Nurses are faced with inadequate physical assessment 28%, formulating diagnoses 56%, plans 34%, implementation 31%, evaluation 37,5%, and communication skills 41%. Aims to develop an ISS learning model based on transformative learning theory and digitalization (TLTD) to improve nurses’ competencies. Method: Used Explanatory cross-sectional involved 190 practitioner nurses. Variables of individual characters (X1), facilities (X2), Social environment support/SES (X3), TLTD (X4), ISS (X5), and nursing competencies (Y) were measured. Data was collected using a checklist questionnaire, conducted on 6 June to 10 August 2022 at Dili, Baucau, and Maliana hospitals. Used descriptive and inferential analysis with SEM-PLS. Result: Five of the 11 hypotheses of statistical p-value < 0,05 and T-Test > 1,96, including X2>X4, X3>X5, X4>X5, and X5>y, to form ISS learning model. The characteristic of respondents were 81,8% young adults, 67,9% women, 57,8% undergraduates, judging the previous training 35% was unsuccessful, and 45,8% did not meet expectations. Learning facilities that are still lacking include policies 23,7%, curriculum 23,4%, guideline 22,7%, modules 27,9%, infrastructure 20,3%, social environment support 24,2% low, organizational support, 30,0% low peer support and 26,3% low family support. The average TLTD is 25,3% to 34,2%, ISS 22,1% to 30,5%, and nurse competence 25,3% to 30,5%.Suggestion: Result of the study become base to improve nurse’s competencies. Conclusion: Learning model was formed by facilities, SES, TLTD, ISS, and nurses’ competencies.

Due to the advancement and availability of internet in present age, device tend to become wireless as well. Mobile ad-hoc network is a wireless environment that consist of advanced agility of nodes and does not contain on any central administrative authority. As it does not contain any central administrative authority so being wireless environment, the network is vulnerable to security threats and suffers in performance as well. Security of MANET is the core issue in this era, meanwhile the data is sent over untrustworthy network. Several techniques were proposed to secure data over Mobile Adhoc Network though cryptography that is one of the most reliable techniques to protect data. In our proposed methodology a Secure Cryptographic technique for Mobile Adhoc Networks (SCTMA) we proposed A Collusion attack prevention (CAP) scheme with ElGamal key generator along with DNA encryption Algorithm is used to make it more secure. The proposed scheme protects the network against collusion attacks and improves the performance as well. Performance analysis will be measured on the basis of key generation time, response time, encryption time and decryption time. The proposed scheme also protects the network against collusion attacks.

An analytical method was established by HPLC-DAD-ELSD with C18-NH2 column tandem for the simultaneous determination of hydrophobic components atractylenolide I, II, III, atractylone and hydrophilic compounds glucose, fructose and sucrose in the dried rhizome of Atractylodes macrocephala Koidz (a natural raw material for health foods, Bai-Zhu aka. in Chinese). The method combines different separation capabilities of reversed-phase liquid chromatography and hydrophilic interaction liquid chromatography, can provide a new choice for the simultaneous determination of hydrophilic and hydrophobic compounds in traditional Chinese medicines and health foods. It provided a reference method for the quality control of Bai-Zhu. The results showed that the linear correlation coefficients of the established column tandem chromatographic method were all greater than 0.9990, the relative standard deviation was 0.1%-2.8%, and the average recovery was 96.7%-103.1%. The contents of atractylenolide I, II, III, atractylone, fructose, glucose, and sucrose in 17 batches of Baizhu were 172.3-759.8 μg/g, 201.4-612.8 μg/g, 160.3-534.2 μg/g, 541.4-8723.1 μg/g, 6.9-89.7 mg/g, 0.7-7.9 mg/g, and 1.2-21.0 mg/g, respectively.

The majority of current methods for measuring the angular deflection of a laser beam enable measurement only in one selected plane. However, there are tasks in which measurements of laser beam deflections in 3D are required. In this paper, we present a way of enabling two-axial measurements of the deflection of a beam based on a single-axis sensor. The key idea is to direct a laser beam alternately into one of two arms of a measurement system. In the first arm, the beam is transmitted directly to the angular sensor, while in the second, the beam is directed to the sensor via a special optical element that rotates the plane of the beam deflection; in other words, this element changes the deflection in the horizontal plane into a deflection in the vertical plane, and vice versa. To alternate the path of the beam, a variable phase retarder and a polarising beamsplitter are used. The proposed technique is experimentally verified, and the results confirm its effectiveness.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

Diving decompression theory hypothesizes inflammatory processes as a source of micronuclei which could increase related risks. Therefore, we tested 10 healthy, male divers. They performed 6-8 dives with a maximum of two dives per day at depths ranging from 21 to 122 msw with CCR mixed gas diving. Post-dive VGE were counted by echocardiography. Saliva and urine samples were taken before and after each dive to evaluate to evaluate inflammation: ROS production, lipid peroxidation (8-iso-PGF2), DNA damage (8-OH-dG), cytokines (TNF-, IL-6, and neopterin). VGE exhibits a progressive reduction followed by an increase (p<0.0001) which parallels in-flammation responses. Indeed, ROS, 8-iso-PGF2, IL-6 and neopterin increases from 0.19 ± 0.02 to 1.13 ± 0.09 μmol.min−1 (p<0.001); 199.8 ± 55.9 to 632.7 ± 73.3 ng.mg-1 creatinine (p<0.0001); 2.35 ± 0.54 to 19.5 ± 2.96 pg.ml-1 (p<0.001); and 93.7 ± 11.2 to 299 ± 25.9 μmol·mol−1 creatinine (p=0.005), respectively. The variation after each dive was held constant around 158.3 ± 6.9% (p = 0.021); 151.4 ± 5.7% (p <0.0001); 176.3 ± 11.9% (p<0.0001); and 160.1 ± 5.6% (p<0.001), respectively. When oxy-inflammation reaches a certain level, it exceeds hormetic coping mechanisms allowing second-generation micronuclei substantiated by an increase of VGE after an initial continuous decrease consistent with a depletion of “first generation” pre-existing micronuclei.

A Berry geometrical phase is identified in a strongly metastable system containing dynamically responsive clathrate hydrate structures within a crystal-fluid material. High energy degeneracy in the associated chemistry produces local stability and false vacuum conditions that lead to non-extensive and non-additive contributions in the fundamental thermodynamic relation. Application of Ginzburg-Landau theory and the scaling laws reveals a coherence length and a penetration depth for a macro-scale dual superconductor. The coherence length determines non-extensive volume changes whilst its inverse gives the Higgs mass. The penetration depth determines the extent of QCD vacuum suppression whilst its inverse gives the vector boson mass together with indirect manifestation as non-additive hyperbolic curvature. Simultaneous emergence of the Ginzburg-Landau superconducting phase transition is consistent with gauge-invariant coupling of the scalar field to the Yang-Mills action in QCD. The discovery of an energy gap in the gradient energy term of the system Lagrangian is associated with a critical correlation length revealed in the transition from a gapped to a gapless superconducting state. Together with the emergence and absorption of the Higgs-like scalar field, a mechanism for describing a renormalized QCD mass gap arises.

Thyroid hormones are essential for regulating the metabolic rate, growth, development, and maintenance of many physiological processes in vertebrates. They are synthesized by the thyroid gland, which is an ancient organ that evolved early in vertebrate evolution. This study aims to characterize the evolutionary path of polymorphic variants associated with the hypothalamus-pituitary-thyroid (HPT) axis by comparing ancient DNA (aDNA) sequences of Late Pleistocene-Holocene hominin populations with those of modern humans. We evaluated the genetic sequences of several populations, including Neanderthals, Denisovans, Palaeolithic hunter-gatherers from European Russia and Sunghir, and Neolithic hunter-gatherers/farmers from Anatolia focusing on genes involved in the development of the thyroid gland and thyroid hormone (TH) biosynthesis, secretion, and transport. Results showed interesting variants in the DIO2 (rs225014), TPO (rs4927611), and TG (rs2069556 and rs1133076) genes. All SNPs seemed to confirm that Neanderthals, and in part Denisovas, were physiologically hypothyroidic. Probably they had lower T3 levels due to defective production or peripheral conversion. From the moment that the most favourable alleles in terms of T3 production appear during the Paleolithic, we are inclined to assume that their selection was linked to environmental pressure.Our study supports insight into the evolutionary history of the endocrine system and can help in providing understanding into the evolution of physiological systems and their adaptation to changing environments. Understanding the evolution of thyroid hormones can also shed light on the mechanisms underlying thyroid disorders in humans.

Background: As the most invasive breast cancer (BrCa), triple-negative BrCa (TNBC) has the worst survival. The use of dexmedetomidine potentially affected BrCa surgery and dexmedetomidine was reported to have direct effects on TNBC cells. The objective of this study is to explore the mechanisms underlying the effect of dexmedetomidine on TNBC. Methods: Dexmedetomidine targets were predicted using The Cancer Genome Atlas data SwissTargetPrediction. Cell lines MDA-MB-231, MCF7, and MCF10A were used to validate the targets in TNBC with both clinical samples and cell lines. Cancer cell lines and normal breast cell lines were grouped in cancer and normal groups respectively. Both groups were exposed to dexmedetomidine treatment. Cell Counting Kit-8 was used to determine the effect of dexmedetomidine on cells with target silencing. The binding model of the candidate targets was docked and critical amino acids were mutated to validate the binding model. Results: Dexmedetomidine selectively inhibits cancer cells. Catalytic subunit of the DNA-dependent protein kinase (PRKDC), indoleamine 2,3-dioxygenase 1 (IDO1), opioid receptor kappa 1 (OPRK1), glutaminyl-peptide cyclotransferase (QPCT), macrophage migration inhibitory factor (MIF), potassium voltage-gated channel, subfamily H (Eag-related), member 2 (KCNH2), cholinergic receptor, muscarinic 3 (CHRM3), and potassium intermediate/small conductance calcium-activated channel, subfamily N, member 4 (KCNN4) were identified as dexmedetomidine targets in TNBC. The expression levels of PRKDC, IDO1, MIF, KCNH2, CHRM3, and KCNN4 were found to be upregulated in TNBC tissues compared to non-TNBC tissues(p<0.05). Silencing of these genes was found to reduce the sensitivity of TNBC cells to dexmedetomidine(p<0.05). This effect was counteracted when the silenced genes were overexpressed, resulting in an increase in the sensitivity of cells to dexmedetomidine (p<0.05). Furthermore, a direct interaction between dexmedetomidine and IDO1 and CHRM3 was observed, which regulated the sensitivity of cells to dexmedetomidine(p<0.05).Conclusion: IDO1 and CHRM3 are direct targets of dexmedetomidine in TNBC.

We review the basics of nuclear binding energy scheme assumed to be associated with the existence of a new strong elementary charge associated with square root of reciprocal of the strong coupling constant.

This study reports the development of a numerical method to simulate two-phase flows of Newtonian fluids that are incompressible, immiscible, and isothermal. The interface in the simulation was located and reconstructed using the geometric volume of fluid (VOF) method. The implementation of the Piecewise-Linear Interface Calculation (PLIC) scheme of the VOF method was performed to solve the three-dimensional (3D) interface transport during the dynamics of two-phase flows. In this method, the interface is approximated by a line segment in each interfacial cell. The balance of forces at the interface was accounted for using the continuum interfacial force (CSF) model. To solve the Navier-Stokes equations, meshless finite difference schemes from the HiG-Flow computational fluid dynamics software were employed. The 3D PLIC-VOF HiG-Flow algorithm was used to simulate several benchmark two-phase flows for the purpose of validating the numerical implementation. First, the performance of the PLIC implementation was evaluated by conducting two standard advection numerical tests: the 3D shearing flow test and the 3D deforming field test. Good agreement is obtained for the 3D interface shape using both the 3D PLIC-VOF HiG-Flow algorithm and those found on the scientific literature. In addition, the absolute error of the volume tracking advection calculation obtained by our 3D PLIC-VOF HiG-Flow algorithm was found to be smaller than the one found in the scientific literature for both the 3D shearing and 3D deforming flow tests. Lastly, the 3D bubble rising problem was simulated for different fluid densities and viscosity’s ratios. Again, good agreement is obtained for the 3D interface shape using both the newly implemented algorithm and the OpenFOAM, DROPS and NaSt3D software. The bubble’s rise velocity and evolution of the bubble’s center of mass is also computed with the 3D PLIC-VOF HiG-Flow algorithm and found to be in agreement with these software.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The theory of Ismail's non-extensive maximum entropy solution (NME) is described in detail. It is used as an inductive inference technique for heavy-tailed queues with a non-robust mean queue length and a non-extensive "long-range" interaction. In our novel method, we substitute the non-robust mean queue length for the conventional Pollaczeck-Khinchin mean queue length. In other words, the new non-extensivity parameter q will be included in the resulting state probability function. Numerical portraits are provided to capture the influential effect of the derived formalism, , on the stable M//1 queue with heavy tails. More potentially, some applications of Hurst Exponent to social computing and connected health are provided. Conclusion with some challenging open problems and possible future research pathways are given.

The popular motor drive systems with a single two-level voltage source inverter (VSI) have one main problem that is the occurrence of the common-mode voltage (CMV), which is an effect of the electromagnetic interference, shaft voltage, bearing currents, leakage current. These cause the high stress, increasung temperature and early mechanical failure in machine. To overcome this problem, the technology of the dual two-level VSI fed open-end three-phase ac loads is now available to eliminate the CMV at the ac/induction motor load with the 120-degree modulation technique for controlling each inverter. In this paper, the discontinuous space vector modulation (DSVM) schemes are proposed and applied for the dual two-level VSI fed open-end load. It is based on the 120-degree modulation technique by using only 12 active voltage vectors and the 10 zero voltage vectors from the total 64 voltage vectors along with the different five-segment swicthing sequence designs with centralizing pulse width modulation technqiue in order to not only cancel the CMV in the ac load, but also reduce the switching number/switching loss of the conversion system. Among the various DSVM schemes, their performances are compared in this paper, such as the number of the switching, the step and peak value of the CMV in each inverter, and the quality of the output waveform, etc. The details of the verfication and comparison are carried out by simulation using Matlab/Simulink software.

Improving the level of farmers' participation in collective action is an important way to promote rural revitalization and improve the sustainable livelihood level of farmers in underdeveloped areas. Based on 312 questionnaires of farmers in Shanxi Province, this paper investigates the status of farmers' participation in collective action, their sustainable livelihood level and the sustainable livelihood effect of collective action participation. The results show that: farmers' willingness to participate in collective action is strong, and the participation effect is obvious, but the participation frequency is low, and the participation time is less; The farmers' sustainable livelihood level is relatively low, Empirical research shows that the level of collective action participation will have a significant positive impact on Farmers' livelihood risk prevention, livelihood capital accumulation, livelihood mode selection and livelihood income improvement, and the frequency, time and value perception of participation in collective action will have varying degrees of impact on Farmers' sustainable livelihoods. In order to promote farmers' active participation in collective action, it is proposed to strengthen the construction of collective organizations Provide incentives and improve the quality and skills of farmers to enhance the collective concept and other policy recommendations.

Azobenzene photoswitches are fundamental components in contemporary approaches aimed at light-driven control of intelligent materials. Significant endeavors are directed towards enhancing the light-triggered reactivity of azobenzenes for such applications and obtaining water-soluble molecules able to act as crosslinkers in a hydrogel. Here, we report the rational design and the synthesis of azobenzene/alginate photoresponsive hydrogels endowed with fast reversible sol-gel transition. We started with the synthesis of three cationic azobenzenes (AZO A, B, and C) and then incorporated them in sodium alginate (SA) to obtain photoresponsive supramolecular hydrogels (SMHGs). The photoresponsive properties of the azobenzenes were investigated by UV-Vis and ¹H NMR spectroscopy. Upon irradiation with 365 nm UV light, the azobenzenes demonstrated efficient trans-to-cis isomerization, with complete isomerization occurring within seconds. The return to the trans form took several hours, with AZO C exhibiting the fastest return, possibly due to higher trans isomer stability. In the photoresponsive SMHGs, the minimum gelation concentration (MGC) of azobenzenes was determined for different compositions, indicating that small amounts of azobenzenes could induce gel formation, particularly in 5 wt% SA. Upon exposure to 365 nm UV light, the SMHGs exhibited reversible gel-sol transitions, underscoring their photoresponsive nature. This research offers valuable insights into the synthesis and photoresponsive properties of cationic, water-soluble azobenzenes, as well as their potential application in the development of photoresponsive hydrogels.

A rare genetic disorder caused by col18.a1 mutations, inherited mostly in autosomal recessive and rarely in autosomal dominant pattern, giving rise to ocular abnormalities and other associated disorders, the condition is referred to as Knobloch syndrome. This paper overviews the anterior and posterior ocular symptoms in Knobloch patients, thus demonstrating the major findings in Knobloch cases including the mutational analysis which discusses the proteins involved and exon number on which mutations are detected. Animal modeling done by knocking out col18.a1 has also been discussed to determine the functions of this gene which have been identified based on anomalies found in knock-out mice.

Breast cancer brain metastasis (BCBM) is a challenging condition with limited treatment options and poor prognosis. Understanding the interactions between tumor cells and the blood-brain barrier (BBB) is critical for developing novel therapeutic strategies. One promising target is estrogen receptor β (ERβ), which promotes the expression of key tight junction proteins, sealing the BBB and reducing its permeability. In this study, we investigated the effects of 17β-estradiol (E2) and the selective ERβ agonist diarylpropionitrile (DPN) on endothelial and cancer cells. Western blot analysis revealed the expression patterns of ERs in these cell lines, and estrogen treatment upregulated claudin-5 expression in brain endothelial cells. Using in vitro models of the BBB, we found that DPN treatment significantly increased BBB tightness about suppressed BBB transmigration activity of representative HER2-positive (BT-474) and triple-negative (MDA-MB-231) breast cancer cell lines. However, the efficacy of DPN treatment decreased when cancer cells were pre-differentiated in the presence of E2. Our results support ERβ as a potential target for the prevention and treatment of BCBM and suggest that targeted vector-based approaches may be effective for future preventive and therapeutic implications.

This study centered on examining 60 different antibiotics by assessing their primary toxicity parameters through the pkCSM database. The parameters included Max. Tolerated Dose (Human) (log mg/kg/day), Oral Rat Acute Toxicity (LD50) (mol/kg), Oral Rat Chronic Toxicity (LOAEL) (log mg/kg_bw/day), and Minnow Toxicity (LC50) (log mM). The results highlight four potential antibiotics—cefotaxime, ceftriaxone, imipenem, and meropenem—that exhibited lower toxicity effects compared to other compounds. These findings imply a relatively favorable safety profile for these antibiotics concerning the specified toxicity parameters. However, it is crucial to interpret these outcomes within the context of the specific clinical application and to consider additional factors for a comprehensive safety assessment. It's essential to acknowledge that evaluating toxicity is intricate, and the determination of what is considered "less toxic" can rely on specific criteria and the context of use. Furthermore, individual responses to antibiotics may vary, and the selection of an antibiotic should be based on diverse factors, including the specific infection being treated, the patient's health, and potential side effects.

Antibiotic prescription is the first line of treating bacterial diseases. But it affects the composition and function of non-targeted intestinal microbiota. Antimicrobial resistance will be the cause for the death of millions of people worldwide. By considering collateral damage of antibiotics, searching an alternative antimicrobial agent will be a solution to minimize the problems. Probiotics, prebiotics and synbiotics are an alternative to antibiotics. Thanks to GIT microbes as they are responsible for metabolism, energy production, protection from pathogens and immunomodulation. So, it is appreciable if the gut microbiota modulated through consumption of probiotics, prebiotics and synbiotics. Probiotic effects are genus and species specific. To get good health benefit of probiotics, safety of probiotics should be assessed before using them. This is mandatory for prebiotics and synbiotic selection. So this review paper gives information about side effects of antibiotics on gut microbiota, description of probiotics, prebiotics and synbiotics as alternative to antibiotics in modulating GIT microbiota, techniques of assessing safety of probiotics and health benefits of probiotics, prebiotics and synbiotics with scientific evidence in clinical trial and some disagreement and challenges of using probiotics, prebiotics and synbiotics.

Abstract—Hydraulic switching actuators are high efficiency, fast response, and low cost solutions for hydraulic control systems. One of the challenging problems is throttling losses during valve transitions. Previously the authors proposed a zero-flowrate switching method to reduce throttling energy loss of the switching valve, where a hydraulic resonator is applied to make the flowrates through the lines approaching zero before the valves are switched off. The major challenge of this approach is fast switching valves whose transition times are less than 2 ms. In this paper, an improved zero-flowrate switching method is presented. It utilizes the capacity with independent inlet/outlet ports to regulate flowrates through the lines. Models of capacity applied in a simple line with different pressure signals are developed to explore characteristics of the capacity, based on which a complete actuation system is developed. In the complete model, resistance and inductance are optimized to achieve desired flowrate response. The improved zero-flowrate switching method reduces throttling energy losses by 99.945% compared to a hard switching system. The simulation results demonstrated that the improved zero-flowrate switching method performs as expected in the design condition. A capacity with proper volume is able to regulate flowrates through all the lines to zero, with the help of appropriate resistance and inductance. Compared to previous zero-flowrate switching method, the novel strategy allows slower switching valves applied in hydraulic actuation systems and achieves better efficiency performance. This research paves a new avenue for reducing throttling energy losses and improves system efficiency in hydraulic switching actuators, as well as most of the hydraulic switch-mode circuits.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The escalating demand for multifunctional and advanced materials for growing industries has turned scientific exploration to graphene-based hybrid filler polymer composites. The introduction of graphene with other fillers into polymer matrices results in astonishing properties and thus has gained significant attention in recent years. This study addresses the significance of graphene-based hybrid filler polymer composites in progressive materials science and engineering. The paper encloses some traditional and current preparation techniques employed in the fabrication of composites and a comprehensive review of successfully prepared graphene hybrid polymer composites with enhanced mechanical, thermal, and electrical properties reported in published research. The role of different factors, e.g., filler type, aspect ratios, filler-matrix compatibility, dispersion effects, homogeneity, filler orientation through polymer matrices, and curing conditions, are summarized. Finally, the applications in heavy industries, e.g., aerospace, electronics, energy storage, and automotive sectors were also analyzed. We hope this study will serve as a practical resource for new researchers and practitioners to understand and harness the full potential of these composites in various scientific and industrial fields.

Background –The brinjal is of much importance in the warm areas of Far East, being grown extensively in India, Bangladesh, Pakistan, China and the Philippines. It is also popular in Egypt, France, Italy and United States. Preserving soil fertility throughout time by preserving organic matter and soil biological diversity, mechanical intervention, as well as exercise is highly needed in upcoming future. Effect of six different fertilizer, five organic and one synthetic fertilizers listing vermicompost, poultry manure, mustard cake, neem cake, bonemeal and N:P:K study were main concern of this investigation to find out the most suitable fertilizer for the brinjal.Result - the final growth and development through N:P:K @ 1.5%(19:19:19) outperformed all the organic fertilizers but when considering only organic fertilizer performance vermicompost@5 ton/ha was outperforming all the other organic fertilizers. Coming close to it, mustard cake@1.5ton/ha has shown its inheritance in providing nutrients. Use of other organic fertilizers are also effective use of poultry manure can provide nitrogen in higher amount in short time. Higher temperature above 25 degree Celsius cause slow growth, temperature range between 21 to 14 degrees Celsius was found better in terms of growth of flower and fruit formation.Conclusion – our experiment demonstrate specific organic fertilizer use over other fertilizers in terms of brinjal different developemental parameters and there is even comparision between synthetic fertilizer with organic fertilizer readily available in market. Vermicompost showed promising result followed by mustard cake for this specific brinjal genotype in northern plain of Indian subcontinent.

In this paper, we investigate the accuracy and robustness of three classes of methods for solving two-phase incompressible flows on a staggered grid. Here, the unsteady two-phase flow equations are simulated by finite volumes and penalty methods using implicit and monolithic approaches (such as the augmented Lagrangian and the fully coupled methods), where all velocity components and pressure variables are solved simultaneously (as opposed to segregated methods). The interface tracking is performed with a Volume-of-Fluid (VOF) method, using the Piecewise Linear Interface Construction (PLIC) technique. The home code Fugu is used for implementing the various methods. Our target application is the simulation of two-phase flows at high density and viscosity ratios, which are known to be challenging to simulate. The resulting strategies of monolithic approaches will be proven to be considerably better suited for these two-phase cases, they also allow to use larger time step than segregated methods.

The article presents the results of tests of minor head losses through PVC and PP elbows for a flow of water and mixtures of water and sand with grain sizes of up to 0.5 mm and concentrations of 5.6 g∙L-1, 10.84 g∙L-1, and 15.73 g∙L-1. The tests were carried out at variable flow velocities for three elbow diameters of 63, 75, and 90 mm. The flow rate, pressure difference in the tested cross-sections, and temperature of the fluids were measured and automatically recorded. The results of the measurements were used to develop mathematical models for determining the minor head loss coefficient as a function of elbow diameter, sand concentration in the liquid, and Reynolds number. The mathematical model was developed by cross validation. It was shown that when the concentration of sand in the liquid was increased by 1.0 g∙L-1, the coefficient of minor head loss through the elbows increased, in the Reynolds number range of 4.6∙104 − 2.1∙105, by 0.3−0.01% for PP63, 0.6−0.03 % for PP75, 1.1−0.06 % for PP90, 0.8−0.01 % for PVC63, 0.8−0.02 % for PVC75, and 0.9−0.04 % for PVC90. An increase in Re from 5∙104 to 2∙106 for elbows with diameters of 63, 75 and 90 mm caused a 7.3 %, 6.8 %, and 6.0 % decrease in the minor head loss coefficient, respectively.

The bioindicator potential of seagrass ecosystems in coastal trace metal monitoring is low for tropical island ecosystems. This study evaluated the bioindicator potential of six seagrass species exposed to anthropogenic trace metal pollution in the Andaman and Nicobar Islands (ANI) of India. Sediment and seagrass biomass, samples were analyzed for trace metals (Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) from four locations of ANI exposed to anthropogenic contamination. Geo accumulation Index values indicated moderate trace metal contamination in seagrass sediment. Seagrass trace metal accumulation from sediment was both species-specific and location- specific for ANI. Small seagrass species such as H. ovalis, H. beccarii and H. uninervis accumulated the maximum concentration of six trace metals (Cr, Cu, Fe, Ni, Pb, Zn) in their tissues compared to big seagrass species like T. hemprichii and E. acoroides of ANI. This study indicates leaves of small seagrass and roots of big seagrass species can serve as short- and long-term bioindicators respectively, of coastal trace metal contamination in tropical islands of ANI.

Background: Waterborne diseases pose a significant global public health threat, compelling enhanced comprehensive surveillance. This study investigates the current infectious disease and antimicrobial resistance (AMR) surveillance systems, including wastewater and environmental surveillance (WES), in three sub-Saharan African countries: Tanzania, Burkina Faso, and the Democratic Republic of the Congo (DRC). The three countries have their specificities regarding wastewater networks and logistic systems. So, emphasizing the need to strengthen existing disease surveillance, the paper advocates for incorporating WES systems specifically designed for countries' context to monitor waterborne and re-emerging pathogens, as well as AMR.Methods: National workshops were conducted to assess the current clinical and environmental surveillance systems and identify priority pathogens for new environmental monitoring. Data were collected through surveys from experts in academia, research, policy, and healthcare. Results: Prioritized pathogens for WES include waterborne (poliovirus, Salmonella Typhi, Vibrio cholerae), respiratory (influenza A&B, SARS-CoV-2), other (Measles and Rubella, Mycobacterium tuberculosis). Recommended AMR pathogens include drug-resistant Mycobacterium tuberculosis, Salmonella spp., methicillin-resistant Staphylococcus aureus, and extended-spectrum beta-lactamase and carbapenemase-producing E. coli. Tanzania, Burkina Faso, and the DRC employ DHSI2-based centralized electronic systems for clinical data collection, complemented by Excel and paper-based registries. The WES approach is commonly employed for monitoring poliovirus and rarely for AMR and other pathogens. Discussion and conclusions: WES is a valuable tool for early detection of locally circulating human-derived pathogens, aiding in outbreak detection, data-driven epidemic response, and prevention. The availability of WES results underscores the importance of effective sanitation for safeguarding human, animal, and environmental health. WES is a pivotal tool for integrated risk management, preventing waterborne outbreaks, protecting drinking water sources, and ultimately gaining various UN Sustainable Development Goals. The study highlights the importance of customized WES systems in line with each country's context, emphasizing localized approaches for effective monitoring of waterborne pathogens and AMR.

Microplastics and nanoplastics (MP/NPs) have been found everywhere they have been searched. On the top of Everest, in the Mariana Trench, on the clouds e recently, microplastics have been discovered in the human placenta, meconium and babies’ feces. In this review we explain what the consequences of the presence of these pollutants in fetuses and newborns are, with particular attention to human breastfeeding. Finally, we outline the possible political and social solutions to the problem of plastic overproduction that characterizes the modern world.

BACE1 is involved in the production of beta-amyloid peptides, and inhibiting its activity is a potential therapeutic strategy for managing Alzheimer's disease, as excessive beta-amyloid accumulation is a characteristic feature of the disease.Computational results suggest that hypericin has the potential to act as an inhibitor of BACE1. The Molecular Docking results indicate a high binding affinity between hypericin and BACE1, with a notable binding energy score of -10.3 kcal/mol. Additionally, the formation of various chemical bonds, including hydrogen bonds and hydrophobic bonds, further supports the idea that hypericin may effectively interact with the active site of BACE1. It's important to note that while the in silico Molecular Docking results are promising, further in vitro and in vivo studies would be necessary to validate and better understand the inhibitory potential of hypericin against BACE1. Additionally, the practical application of hypericin as a BACE1 inhibitor in a therapeutic context would require careful consideration of factors such as bioavailability, safety, and efficacy.

Enhancing traffic safety is one of the fundamental objectives of Intelligent Transport Systems (ITS), and it aligns closely with the principles of sustainable transport. Due to specific differences in infrastructure, vehicles, and users’ behaviour, places where different modes of traffic intersect are recognized as critical points of the traffic system, making them crucial aspects of Sustainable Urban Mobility Plans (SUMPs) implementation. The SUMPs aim to create urban mobility that is not only environmentally friendly and efficient but also safe for all users. The continuous development and widespread adoption of innovative ITS technologies have paved the way for a system that could provide drivers with real-time information about both immediate and potential dangers at these critical points. This paper provides an overview of previous research in the field, investigating the impact of information systems on drivers’ behaviour, various detection and communication solutions that can be effectively integrated into such a system, as well as a brief overview of models and solutions that have been developed to warn drivers in a similar context. The reviewed literature offered valuable insights on which a novel driver information system architecture framework is proposed. This framework can contribute to the ongoing safety improvement in multimodal transport networks within the context of sustainable transport.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

The normative and safeguarding role of ethics and law in the development of biomedical science and technology, as well as their importance in promoting the progress of the industry, analyzed the key role of ethics and law in the field of biomedical science and technology, by restricting scientific research behavior, protecting the rights and safety of subjects, providing a solid guarantee for scientific research activities, and promoting the healthy development of biomedical science and technology. At the same time, the positive role of ethics and law in promoting international cooperation and exchange of biomedical science and technology is also discussed, which will inject strong impetus into the global development of biomedical science and technology. In addition, through case analysis, the paper demonstrates the key role of ethical review in the field of biomedical science and technology, as well as the importance of law in maintaining market order, protecting subjects' rights and interests, and fairness and justice. The successful practice of ethics and law in the development of biomedical science and technology is emphasized, which proves that following ethical principles and legal framework is the key factor to promote the progress of biomedical science and technology. This paper explores the important role of ethics and law in the development of biomedical science and technology, and provides valuable reference and guidance for practitioners in the industry. By following ethical principles and legal norms, we will jointly promote the prosperity and development of biomedical science and technology, and contribute to the common progress of human health.

Understanding mechanisms of ageing remains a complex challenge for biogerontologists, but recent adaptations of evolutionary ageing theories offer a compelling lens in which to view both age-related molecular and physiological deterioration. Ageing is commonly associated with a progressive loss of biochemical processes and degeneration of molecular material, however, the mechanisms of diminishing function are not simply a result of aberrant expression of these pathways. Natural selection pressures are at their highest in youthful periods to select genes advantageous to maximising reproductive capacity. After sexual maturation, selective pressure diminishes, subjecting individuals to maladaptive pleiotropic gene function once beneficial for developmental growth, but pathogenic later in life. Due to this selective ‘shadowing’ in ageing, mechanisms to counter hyperfunctional genes are unlikely to evolve within a given species. These genetic ‘run-on’ programmes are not dysfunctional per se and, in fact, remain highly robust. Thus, interventions capable of optimising gene function during the ageing process represent as attractive therapeutic modalities. Caenorhabditis elegans offers a unique model to explore high-throughput screening of interventions to combat hyperfunctional pathways involved in ageing. However, the majority of research to date employ whole-life vs late-life pathway manipulation of developmental/growth-related systems to claim ageing attenuation, despite significant impairments in early-life fitness and discordance with healthspan. Here, we discuss data supporting hyperfunctional changes at a global molecular and functional level in C. elegans, and how classical lifespan-extension mutants alter these dynamics. We later discuss the relevance of such mutant models for exploring mechanisms of ageing, highlighting that post-reproductive gene manipulation represents a far more translatable approach for C. elegans research not routed within pleiotropic constraints. More so, lifespan has become a routine readout for quantifying ‘ageing’, however, we make the argument that a compression of gerospan vs lifespan extension is a more meaningful goal for anti-ageing regimes with current knowledge. Similarly, mechanisms governing lifespan are distinct from those regulating health, and slowing senescent pathology accumulation appears more applicable for the abstraction to human ageing.

Abstract Introduction: Poor structural quality of health facilities for tuberculosis (TB) diagnosis and treatment contributes to unfavorable health outcomes among TB patients. Improving the quality of healthcare services helps to avert TB-related morbidity. Despite these facts, the level of structural quality of health facilitieSs to deliver TB services is not in line with what the national TB and leprosy program (NTLP) recommends. Hence, the present study was conducted to assess the structural quality of health facilities to deliver quality TB services to TB patients among public health facilities in the Sidama region.Objectives: To determine the quality of the structural domain of TB services at public health facilities in the Sidama region of southern Ethiopia.Methods: An institution-based cross-sectional study was conducted from June to July 2023 among randomly selected public health facilities in the Sidama region. We included 40 randomly selected public health facilities that delivered TB services in the study area. Data was collected by experienced data collectors using facility audits, clinical observation checklists, structured questionnaires, and in-depth interviews. An Open Kit Mobile (ODK) application was used to collect data and exported to SPSS version 26. All statistical analysis was done using SPSS version 26.Results: The overall mean quality score for the structural dimension was 50.25 among the 40 health facilities audited in the study area.Conclusion: The quality of TB services regarding structural dimensions was poor in the study area. Therefore, any strategies must give careful attention to increasing the comprehensive structural dimension of quality TB services.

This review explores the transformative impact of sensor technologies in early disease detection. It highlights recent advancements in nanotechnology-based sensors, particularly focusing on their applications in identifying disease biomarkers at early stages. The integration of these sensors with artificial intelligence for predictive analytics in healthcare is also discussed. Applications in cancer, infectious diseases, and chronic disease management underscore their diverse utility. Challenges in sensor technology adoption and future directions, including multiplexed sensors and wearable devices, are examined. This review underscores sensors' potential in enhancing disease management and patient outcomes.

Computed tomography (CT) is a widely employed imaging modality with diverse clinical applications in pediatric and adult populations, offering numerous advantages. Despite several alternatives to imaging modalities with ionising radiation, CT scans have demonstrated persistent global popularity, contributing to a substantial amount of effective radiation doses for patients. This exposure results in hazards, including stochastic effects that amplify the radiation-induced cancer risk proportionally to the radiation dose received. CT-related radiation comprises a substantial portion of cumulative effective doses within diagnostic radiology, specifically impacting younger patient cohorts undergoing repeated investigations for chronic diseases over time. Scientific literature over recent decades has explored various methods to mitigate radiation doses during medical imaging. One notable strategy involves implementing low-dose and ultralow-dose CT protocols, maintaining diagnostic efficacy in acute and non-acute medical and surgical conditions. Utilising innovative image reconstruction algorithms, such as iterative reconstruction and emerging deep-learning algorithms based on artificial intelligence, plays a pivotal role in achieving an approximately 80% reduction in patient radiation compared to standard doses. This review article discusses the significance of low-dose protocols across a spectrum of acute and chronic medical conditions affecting different body systems.

Molecular docking, a computational method predicting how molecules bind to target proteins, is employed in this study to explore Polydatin's interactions with Ras-related protein Rab (Rab) proteins using the Mcule Database. This database validates the docking results and offers insights into the pharmacological properties of Polydatin. Notably, specific Rab proteins like Rab-5A, HRas, and Rab-18 exhibit robust interactions with Polydatin, indicated by favorable binding energies.These findings illuminate the potential roles of Polydatin in therapeutic and biological contexts, emphasizing its interaction with Rab proteins. The Mcule Database enhances the credibility of the study, providing additional perspectives on Polydatin's applications. The observed interactions, particularly with key proteins like HRas, present a promising avenue for modulating cellular signaling pathways. This modulation holds therapeutic potential, potentially addressing conditions associated with pathway overactivity, including specific cancer types.

The assessment of Histone deacetylases in conjunction with Curcumin, conducted through the Mcule Database employing the Autodock Vina algorithm, involves an examination of molecular interactions. This analysis includes the calculation of binding energies, revealing the strength and stability of the interactions between Curcumin and various Histone deacetylase targets. The comparison encompasses diverse aspects such as binding energies, specific binding sites, interactions across different targets, structural details, and potential implications for biological activity. The results imply that Curcumin shows heightened affinity for Histone deacetylase 4 in comparison to other investigated histone deacetylases.

Mathematical modeling is the most important tool for constructing the theory of different kinds of two-phase flows. The review is devoted to the analysis of the advent of the approach of mathematical modeling of two-phase flows, where solid particles act mainly as the dispersed phase. The main problems and features of the study of gas-solid two-phase flows are excluded. The main characteristics of gas flows with solid particles are given and the classification of two-phase flows is developed on their basis. The Lagrangian and Euler approaches to modeling the motion of a dispersed phase (particles) are described. Much attention is paid to the consideration of numerical simulation methods that describe descriptions of turbulent gas flow at different hierarchical levels (RANS, LES, DNS), different levels of description of interphase interactions (one-way coupling (OWC), two-way coupling (TWC) and four-way coupling (FWC)), as well as at different levels of interface resolution (partial-point (PP) and particle-resolved (PR)). Excluded are examples of some studies carried out on the basis of the identified approaches, as well as their exclusion for mathematical modeling of various classes of gas-solid two-phase flows.

The fluid seepage in local-saturated zone of subgrade promotes the migration of fine particles in the filler, resulting in the change of pore structure and morphology of the filler and the deformation of solid skeleton, which affects the fluid seepage characteristics. Repeatedly, the muddy interlayer, mud pumping and other diseases are finally formed. Based on the theory of two-phase seepage, the theory of porous media seepage, and the principle of effective stress in porous media, a two-phase fluid-solid coupling mathematical model in local-saturated zone of subgrade considering the effect of fine particles migration is established. The mathematical model is numerically calculated with the software COMSOL Multiphysics○R, the two-phase seepage characteristics and the deformation characteristics of the solid skeleton in local-saturated zone of the subgrade are studied. The research results show that due to the continuous erosion and migration of fine particles in local-saturated zone of the subgrade, the volume fraction of fine particles first increases then decreases and finally becomes stable with the increase of time. And the volume fraction of fine particles for the upper part of the subgrade is larger than that for the lower part of the subgrade. The porosity, the velocity of fluid, the velocity of fine particles, and the permeability show a trend of increasing first and then stabilizing with time; the pore water pressure has no significant changes with time. The vertical displacement increase first and then decrease slightly with the increase of time, and finally tend to be stable. For a filler with a larger initial volume fraction of fine particles, the maximum value of the volume fraction of fine particles caused by fluid seepage is larger, and the time required to reach the maximum value is shorter. It can be concluded that in actual engineering, the volume fraction of fine particles in the subgrade filler should be minimized on the premise that the filler gradation meets the requirements of the specification.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

Green economy has emerged as a significant pillar of sustainable development in the current global context, and the unpredictability of economic policy has progressively garnered the interest of businesses and government officials as one of the obstacles they must confront. This paper examines how uncertainty in the green economy impacts the green economy's efficacy. The research concentrates on how changes in a particular region can result in geospatial diffusion (spatial spillover), which is a form of spatial spillover wherein the uncertainty of the green economy can impact its efficacy. This paper examines the policy formulation and current state of the green economy across various regions, as well as the diffusion of economic policy uncertainty across geographical areas and the subsequent impact on the green economy's status quo. There is a negative correlation between economic policy uncertainty and green economy efficacy, according to research. There is a spatial spillover effect between economic policy uncertainty and the efficacy of the green economy. Regional variations exist in the impact of economic policy uncertainty on the efficacy of the green economy. The findings indicate that the implementation of AI has a more substantial beneficial effect on carbon emissions. An increase in carbon dioxide emissions poses a growing challenge for the industrial sector in its pursuit of carbon neutrality.

Climate change will pose a challenge for the winemaking sector worldwide, bringing progressively drier and warmer conditions and increasing the frequency and intensity of weather extremes. The short-term adaptation strategy of applying biostimulants through foliar application serves as a crucial measure in mitigating the detrimental effects of environmental stresses on grapevine yield and berry quality. The aim of this study was to evaluate the effect of foliar application of a seaweed based biostimulant (A. nodosum – ANE) and glycine betaine (GB) on berry quality, bioactive compounds, antioxidant activity, and elucidated their action on the secondary metabolism. A trial was installed in a commercial vineyard (cv. ‘Touriga Franca’) in the Cima Corgo (Upper Corgo) sub-region of the Douro Demarcated Region. A total of four foliar sprayings were performed during the growing season: at flowering, pea size, bunch closer, and veraison. There was a positive effect of GB in the berry quality traits. Both ANE and GB increased the synthesis of anthocyanins and other phenolics in berries and influenced the expression of genes related to the synthesis and transport of anthocyanins (CHS, F3H, UFGT, MATE1 and GST). So, they have the potential to act as elicitors of secondary metabolism, leading to improved grape quality, but also sets the foundation for sustainable agricultural practices in the long run.

With reference to our 4G model of final unification, strong coupling constant and strong interaction charge of magnitude $e_s\cong 2.95e$, it is possible to understand the nuclear stability range with a simple power law of the form, $A_s\cong \left(Z+2.95\right)^{1.2\pm0.015}$

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

In this paper we introduce the New/Generalized two parameter Gamma function and Pochhammer symbol. We named them, as Generalized p - k Gamma Function and Generalized p - k Pochhammer symbol and denoted as $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ respectively. We prove the several identities for $ _{p}^{a}\Gamma_{k}(x) $ and $ _{p}^{a}(x)_{n,k} $ those satisfied by the classical Gamma function. Also we provide the integral representation for the $ _{p}^{a}\Gamma_{k}(x) $

This paper explores the views of a group of young men aged 16–18, studying towards a Level 1 diploma in music in the North East area of England. It uses the conceptualization of “social haunting” to focus our discussions about how Level 1 learners articulated their experiences in the context of their learning journeys and perceived marginalization. The research took place at a large Further Education (FE) college and included a series of five “research encounters” with the group of Level 1 learners. These encounters included a range of activities, resulting in a variety of data being collected, including several activity worksheets, structured and unstructured focus group interviews, and questionnaires. This paper focusses on the outcomes of a single research activity that focused on exploring the topic of marginalization. We present a discussion on social haunting as one of the emerging findings from this research encounter, outlining how the reality of the social and cultural legacy of the UK’s industrial past can shape today’s youth and their futures. We will talk about the young men’s views of marginalization, their school-to-work transitions, the formation of masculinity in post-industrial communities and the role of Further Education in it. The paper concludes by discussing some insights for practice and future research.

Proteins are considered to be the main carriers of antigenic properties of Mycobacterium tuberculosis and Mycobacterium bovis, the causative agents of tuberculosis, the most serious infectious disease. Neutrophils, following resident macrophages, are among the first to attack the mycobacteria in defense of the organism. Neutrophils themselves are also the target of mycobacterial products; and their effect on neutrophil functions has been less studied. We have obtained about 70 protein fractions from M. bovis lysate; among them four protein fractions (10, 22, 24, and 40 kDa) had high serological activity against the serum of a rabbit immunized with M. bovis cells. We studied the effect of the serologically active proteins isolated from M. bovis on the generation of reactive oxygen species by bone marrow granulocytes of the Balb/c mouse, evaluated by luminol-dependent chemiluminescence. For comparison, two synthetic peptides (both 3 kDa) carrying immunogenic epitopes of MPB 70 protein (M. bovis) were taken. Proteins of 10, 22, and 24 kDa at concentrations of 83, 80, and 59 ng/mL, respectively, were found to activate ROS generation by mouse granulocytes. The 10- and 40-kDa antigens inhibited the receptor-mediated respiratory responses to opsonized zymosan (OZ) and N-formyl-MLF peptide (fMLF) but significantly enhanced the response to the phorbol ester PMA, which directly activates protein kinase C. Antigens with molecular weights of 22 and 24 kDa enhanced the fMLF-induced response and had no effect on the response activated by PMA. The response to OZ was suppressed in the presence of the 22 kDa protein. Synthetic peptides over a wide range of concentrations showed no activity in any case. All M. bovis proteins examined did not affect both proliferation and cell viability of the A549 and THP-1 cells; therefore, they have no cytotoxic or proliferative effects. Thus, serologically active proteins with molecular weights of 10, 22, 24, and 40 kDa isolated from M. bovis modulated the respiratory responses of mouse granulocytes induced by the formyl peptide, while proteins of 10, 22, and 40 kDa inhibited the responses induced by OZ.

For the first time, this study identified seven potential ligands with high binding energies through the docking approach against the Crystal Structure of human Melanoma-associated antigen B1 (MAGEB1). The ligands—Imatinib, Bafatinib, Diosmin, Ginkgetin, Bilobetin, Amentoflavone, and Hypericin—showing strong binding energies around -10 kcal/mol, indicate a potentially robust interaction with the target protein. Moreover, the additional step of predicting toxicity properties using the pKCSM server provides valuable insights into the safety profiles of these ligands. From these results, the parameters for Diosmin: —Max. tolerated dose (human),- Oral Rat Acute Toxicity (LD50), and - Oral Rat Chronic Toxicity (LOAEL)—suggest a favorable safety profile, making it a potential candidate for further consideration against Melanoma. Moving forward, it's advisable to conduct further experimental validations, including in vitro and in vivo studies, to confirm the efficacy and safety of Diosmin and other potential ligands. Consideration of pharmacokinetics, metabolism, and specific mechanisms of action will contribute to a comprehensive understanding of these compounds' potential as therapeutic agents.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

In this paper, some characterizations of fuzzifying strong compactness are given, including characterizations in terms of nets and pre -subbases. Several characterizations of locally strong compactness in the framework of fuzzifying topology are introduced and the mapping theorems are obtained.

The strong coupling between individual quantum emitters and resonant optical micro/nanocavities is beneficial to understand light and matter interactions. Here we propose a plasmonic nanoantenna placed on a metal film to achieve an ultra-high electric field enhancement in the nanogap and ultra-small optical mode volume. The strong coupling between a single quantum dot and the designed structure is investigated in detail by both numerical simulations and theoretical calculations. When a single QD is inserted into the nanogap of the silver nanoantenna, scattering spectra show remarkably large spectral splitting and typical anti-crossing behavior of the vacuum Rabi splitting, which can be realized in the scattering spectra by varying the nanoantenna thickness. Our work shows a possible way to enhance light-matter interaction at a single quantum emitter limit, which can be useful for future quantum and nanophotonic applications.

New setting is introduced to study chromatic number. Neutrosophic chromatic number and chromatic number are proposed in this way, some results are obtained. Classes of neutrosophic graphs are used to obtains these numbers and the representatives of the colors. Using colors to assigns to the vertices of neutrosophic graphs is applied. Some questions and problems are posed concerning ways to do further studies on this topic. Using strong edge to define the relation amid vertices which implies having different colors amid them and as consequences, choosing one vertex as a representative of each color to use them in a set of representatives and finally, using neutrosophic cardinality of this set to compute neutrosophic chromatic number. This specific relation amid edges is necessary to compute both chromatic number concerning the number of representative in the set of representatives and neutrosophic chromatic number concerning neutrosophic cardinality of set of representatives. If two vertices have no strong edge, then they can be assigned to same color even they’ve common edge. Basic familiarities with neutrosophic graph theory and graph theory are proposed for this article.

The purpose of this paper is to bring to light a method through which the global in time existence for arbitrary large in H¹ initial data of a strong solution to 3D periodic Navier-Stokes equations follows. The method consists of subdividing the time interval of existence into smaller sub-intervals carefully chosen. These sub-intervals are chosen based on the hypothesis that for any wavenumber m, one can find an interval of time on which the energy quantized in low-frequency components (up to m) of the solution u is lesser than the energy quantized in high-frequency components (down to m) or otherwise the opposite. We associate then a suitable number m to each one of the intervals and we prove that the norm ||u(t)||_H1 is bounded in both mentioned cases. The process can be continued until reaching the maximal time of existence T_max which yields the global in time existence of strong solution.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

In the decarbonization of the steel, cement, and chemical industry in Germany, green hydrogen is expected to play a crucial role. The utilization of green hydrogen in the production processes of said industries requires organizations to modify their business model, requiring sustainable business model innovation (SBMI). Numerous tools and frameworks that support organizations in the process of SBMI have been proposed in the literature in recent years. However, the applicability of these tools and frameworks for steel, cement, and chemical companies that intend to utilize green hydrogen to produce their goods remains unexplored. By conducting a systematic literature review on tools and frameworks for SBMI, a literature and practice review to identify and analyze existing green hydrogen projects of steel, cement, and chemical companies, and an evaluation of the identified tools and frameworks in an evaluation matrix, this paper aims to assess the suitability of SBMI tools and frameworks for steel, cement, and chemical companies that plan to use green hydrogen to produce their goods. Based on the evaluation, the Cambridge Business Model Innovation Process (CBMIP) was identified as the most suitable SBMI framework.

Sorghum grain processing can improve the nutritional content by promoting dietary properties that contribute to food security and economic development. The quality, nutritional content, and processing properties of sorghum bicolor grain can greatly affected by the inbred line races and variance in pericarp colour.The current study assessed the influence of the Husking Fraction Time Units (HFTU) process, which employed set time units per second (S), on the variation in the nutritional profile of fifty-one inbred line sorghum varieties based on distinct pericarp colours. When the assessment of the nutritional profile was involved: dry matter, total protein besides, namely mineral (P, K, S, Ca, Mg, Na, Fe, Zn, and Mn). The variety groups showed a significance value of (P < 0.05), indicating the study hypothesis's truth.The results demonstrated substantial impacts implied by the Husking Fraction Time Unit (HFTU) technique. This occurrence was noted when the dry matter percentage was increased in the husked products, specifically the endosperm (grits) and bran. The protein percentage redistributed by 19.2% compared to the whole grain and bran content. In comparison, the ratio of N/S was 14:1 in the S. bicolor and 12:1 in the kafirin in the bran part. Moreover, a strong correlation was observed among the examined minerals of S.bicolor and kafirin, such as the correlation between Ca: P, K: Na, and Fe: Zn attributed 80 (S) time unit, with correlation coefficients of R = 0.784 and R = 0.586, R= 517, R= 0.884, R= 0.745, and R = 0.893, respectively. At the same time, the 80 (S) time unit showed a significant effect on the colour property profile.The study results could benefit breeders and nutrition specialists in developing genotypes and processing sorghum grains, promoting research, and aiding several industrial sectors owing to the grain's adaptability and nutritional properties.

In this preliminary investigation, a concise molecular docking study using the Pyrx program screened thousands of compounds against the active site of HIV-1 reverse transcriptase. The Virtual Screening library was employed to assess binding energetics scores, focusing on identifying candidates with high Vina Scores. Eight compounds, including Tetrophan, Imatinib, Amentoflavone, Alprazolam, Bilobetin, Bafetinib, Nilotinib, and Ginketin, emerged as promising candidates with significant binding energies.Recognizing compounds that strongly bind to HIV-1 reverse transcriptase holds potential for antiretroviral drug development in the fight against HIV infection. Subsequently, the study evaluated the toxicity properties of these candidates using pKCSM. Amentoflavone, a natural biflavonoid found in Ginkgo biloba and Nilotinib, a tyrosine kinase inhibitor, demonstrated lower overall toxicity profiles compared to other candidates. Further toxicity analysis using Pro-Tox-II revealed Amentoflavone's higher predictive LD50, lower toxicity class, and reduced probabilities of hepatotoxicity, carcinogenicity, mutagenicity, and moderate immunotoxicity compared to Nilotinib. While Nilotinib, a pharmaceutical drug, exhibited higher probabilities of adverse effects in these categories. In summary, Amentoflavone and Nilotinib present as promising candidates with lower toxicity concerns. Amentoflavone, as a natural substance, showcases a more favorable toxicity profile than Nilotinib, offering valuable insights for potential therapeutic applications.

Background: Increase of collagen I (COL I)/COL III ratio enhances vessel wall stiffness and renders vessels less resistant to blood flow and pressure changes. We hypothesized that COL I/COL III ratio is increased in the brain arteriovenous malformations (bAVMs), which is associated with bAVM hemorrhage. Method: Surgically resected human bAVM samples and mouse bAVMs induced in three transgenic mouse lines with activin receptor-like kinase 1 or endoglin deletion in the endothelial cells or in the brain focally. Colony-stimulating factor receptor inhibitor was used to transiently deplete microglia. COL I and COL III levels, hemorrhage, and gene expression in bAVMs were analyzed. Results: The COL I and COL III levels and the COL I/COL III ratio were higher on human and mouse bAVMs than controls, which was associated with bAVM hemorrhage. Col I and Col III mRNAs were also increased in mouse bAVMs. The degree of microhemorrhage in mouse bAVMs was positively correlated with Col I/Col III ratios. Transient depletion of microglia reduced Col I/Col III ratio and microhemorrhage in mouse bAVMs. Conclusion: COL I/COL III ratio are increased in bAVM vessels, which is associated with bAVM hemorrhage. Depletion of microglia reduces Col I/Col III ratio and hemorrhage in mice bAVMs.

This paper reviews the unilateral and bilateral, one- and two-dimensional Laplace transforms. The unilateral and bilateral Laplace transforms are compared in the one-dimensional case, leading to the formulation of the initial-condition theorem. This problem is solved with all generality in the one- and two-dimensional cases with the bilateral Laplace transform. General two-dimensional linear systems are introduced and the corresponding transfer function defined.

From experimental studies of protein folding, it is now clear that there are two types of folding behavior, i.e., two-state folding and non-two-state folding, and understanding the relationships between these apparently different folding behaviors is essential for fully elucidating the molecular mechanisms of protein folding. This article describes how the presence of the two types of folding behavior has been confirmed experimentally, and discusses the relationships between the two-state and the non-two-state folding reactions, on the basis of available data on the correlations of the folding rate constant with various structure-based properties, which are determined primarily by the backbone topology of proteins. Finally, a two-stage hierarchical model is proposed as a general mechanism of protein folding. In this model, protein folding occurs in a hierarchical manner, reflecting the hierarchy of the native three-dimensional structure, as embodied in the case of non-two-state folding with an accumulation of the molten globule state as a folding intermediate. The two-state folding is thus merely a simplified version of the hierarchical folding caused either by an alteration in the rate-limiting step of folding or by destabilization of the intermediate.

As a high-frequency carrier, the Terahertz (THz) wave is essential for achieving high-data-rate wireless transmission due to its ultra-wide bandwidth. Phase stabilization becomes crucial to enable phase-shift-based multilevel modulation for high-speed data transmission. We developed a Mach-Zehnder interferometric phase stabilization technique for photomixing, which has proved a promising method for phase-stable continuous THz-wave generation. However, this method faces inefficiencies in generating phase-modulated THz waves due to the impact of the phase modulator on the phase stabilization system. By photomixing, which is one of the promising methods for generating THz waves, the phase of the generated THz waves can be controlled in the optical domain so that the stability of the generated THz wave can be controlled by photonics technologies. Thus, we have devised a new phase stabilization approach using backward-directional lightwave, which is overlapped with the THz wave generation system. This study presents a conceptual and experimental framework for stabilizing the phase differences of optical carrier signals. We compare the optical domain and transmission performances between forward-directional and backward-directional phase stabilization methods. Remarkably, our results demonstrate error-free transmission at a modulation frequency of 3 Gbit/s and higher.