Ultrasonic transducers are widely used for non-destructive testing (NDT) and evaluation in various industries. While capacitive micromachined ultrasonic transducers (CMUTs) have emerged as significant novel transducers, their application in NDT has been limited. This study designed and fabricated a novel two-element CMUT device for NDT applications. The CMUT’s structural parameters were introduced, and the device was fabricated using silicon fusion wafer-bonding technology. The transducer’s sensitivity, bandwidth, and pulse-echo response performance were tested and analyzed. Testing with aluminum blocks demonstrated that the two-element transducer can transmit and receive ultrasonic waves, with central operating frequencies of 3.35 MHz. In addition, at 3.4 MHz, the receive sensitivities of both elements were –197.434 dB and –197.413 dB, respectively, meeting the requirements for NDT systems. In pulse-echo response testing, the CMUT successfully detected signals from the aluminum block interface and located the interface’s position. This study highlights the potential of CMUTs for NDT testing and evaluation applications.

The present paper aims to increase knowlodge of the methods of resistance estimating of concrete in situ by means of non-destructive tests used to integrate the quantitative results from cylindrical specimens (core). The results of experimental investigations carried out on concrete conglomerate samples of a school building are shown. The experimental campaign then will be presented like a case study, conducted on a series of concrete beams and pillars of an existing building. The distructive tests on cores were conducted at the Civil Structures Laboratory of the Engineering Department of the University of Campania "Luigi Vanvitelli". The expression obtained through the calibration procedure of the values of non-destructive tests with those provided by the core drills allowed to estimate the average values of the compressive strength of the concrete. It is highlighted how this result was achieved with a very limited core number provided that they are extracted in selected points and that there was a proportionality link with the resistances obtained from non distructive tests.

Eddy current testing can be used to interrogate steels but it is hampered by the lift-off distance of the sensor. Previously, the lift-off point of intersection (LOI) feature has been found for the pulsed eddy current (PEC) testing. In this paper, a lift-off invariant inductance (LII) feature is proposed for the multi-frequency eddy current (MEC) testing, which merely targets the ferromagnetic steels. That is, at a certain working frequency, the measured inductance signal is found nearly immune to the lift-off distance of the sensor. Such working frequency and inductance are termed as the lift-off invariant frequency (LIF) and LII. Through simulations and experimental measurements of different steels under the multi-frequency manner, the LII has been verified to be merely related to the sensor parameters and independent of different steels. By referring to the LIF of the test piece and using an iterative inverse solver, one of the steel properties (either the electrical conductivity or magnetic permeability) can be reconstructed with a high accuracy.

For the electromagnetic eddy current testing, various methods have been proposed for reducing the lift-off error on the measurement of samples. In this paper, instead of eliminating the measurement error caused by the lift-off effect, an algorithm has been proposed to directly measure the lift-off distance between the sensor and non-magnetic conductive plates. The algorithm is based on a sample-independent inductance (SII) feature. That is, under high working frequencies, the inductance is found sensitive to the lift-off distance and independent of the test piece under an optimal single high working frequency (43.87 kHz). Furthermore, the predicted lift-off distance is used for the thickness prediction of the non-magnetic conductive samples using an iterative method. Considering the eddy current skin depth, the thickness prediction is operated under a single lower frequency (0.20 kHz). As the inductance has different sensitivities to the lift-off and thickness, the prediction error of the sample thickness is different from that of the lift-off distance. From the experiments on three different nonmagnetic samples – aluminium, copper, and brass, the maximum prediction error of the lift-off distance and sample thickness is 1.1 mm and 5.42 % respectively at the lift-off of 12.0 mm.

Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.

Non-Destructive Testing (NDT) is an appealing technique for confirming the welding quality and ensuring structural integrity without causing damage. It assists in regulatory compliance, risk mitigation, and process optimization for improved industrial reliability. This study reviews potential NDT approaches. Through a rigorous analysis of existing surveys, we aim to decipher the current landscape and highlight the significant advancements in the field. Because of the potential of artificial intelligence (AI) assistive X-ray imaging-based NDT, we particularly examine the integration of AI algorithms and X-ray imaging in the NDT of welds. This convergence represents a paradigm shift, redefining traditional methods and ushering in a new era of precision, automation, and efficiency. As we navigate through potential X-ray imaging datasets, delve into crucial image processing techniques, examine feature extraction methods, and explore AI algorithms, our survey reveals the intricate interplay of technologies that drive automated weld defect categorization. The review broadens its focus by including various practical applications, highlighting the adaptable utility of AI-assistive X-ray imaging for weld defect detection in potential industrial applications. Moreover, the promising opportunities and nuanced challenges associated with integrating X-ray imaging and AI in weld integrity assessment are highlighted. It provides a comprehensive perspective on this rapidly evolving field.

Previously, a conductivity invariance phenomena (CIP) has been discovered – at a certain lift-off, the inductance change of the sensor due to a test sample is immune to conductivity variations, i.e. the inductance – lift-off curve passes through a common point at a certain lift-off, termed as conductivity invariance lift-off. However, this conductivity invariance lift-off is fixed for a particular sensor setup, which is not convenient for various sample conditions. In this paper, we propose using two parameters in the coil design – the horizontal and vertical distances between the transmitter and the receiver to control the conductivity invariance lift-off. The relationship between these two parameters and the conductivity invariance lift-off is investigated by simulation and experiments and it has been found that there is an approximate linear relationship between these two parameters and the conductivity invariance lift-off. This is useful for applications where the measurements have restrictions on lift-off, e.g. uneven coating thickness which limits the range of the lift-off of probe during the measurements. Therefore, based on this relationship, it can be easier to adjust the configuration of the probe for a better inspection of the test samples.

This paper presents a new approach of eddy current methods for determining the size of the co-axial hole in the metallic circular disk. In recent decades, for the air-cored sensor probe, the impedance change due to the presence of an infinite metal plate can be calculated by the Dodd-Deeds model. However, in practical measurements, the sample cannot match with the condition required - ‘infinite’, thus the Dodd-Deeds model could not be applied to the disk with finite size and certainly not a co-axial hole in the center. In this paper, a dual-constraint analytical method is proposed. That is, the upper and lower limits of the integration are substituted with specific values instead of the original 0 and . Besides, it is found that, once the outer radius of the disk is fixed (i.e. the lower limit of integration is fixed), the upper limit reduces linearly as the size of the coaxial hole increases. Both the FEM simulation and experiments have been carried out to validate this method. The radius of the hole can be estimated based on the dual-constraint integration feature.

Thermal Non-destructive Testing and Evaluation (NDT&E) is crucial in ensuring the quality and safety of industrial materials, components, and structures. It serves as a key tool for assessing their operational reliability, thus enhancing safety in a wide range of industries. There is a growing demand for dependable, swift, remote, and secure inspection and assessment techniques to detect hidden flaws, especially for sustainable solutions prompts adjustments in design and manufacturing standards. Hidden defects often emerge during the service life of these materials and structures due to various stress factors, potentially resulting in catastrophic failures. This study delves into the optimal and dependable experimental method for conducting fast, remote, and secure inspections and assessments of carbon fiber reinforced polymer materials using Infrared Imaging (IRI) as part of Thermal Non-Destructive Testing and Evaluation (TNDT&E). Additionally, it examines the post-processing approach associated with this technique. This perspective also sheds light on the current state-of-the-art infrared imaging methods employed in TNDT&E, emphasizing their strengths and weaknesses about their ability to detect subsurface defects present within the material Most of the methods discussed in previous research primarily focus on the thermal differences in specific areas of a sample using processed thermal images, even though these images come from analyzing a series of images captured over time. This study highlights the latest research in thermal/infrared non-destructive testing and evaluation, along with the related post-processing techniques. It aims to not only show hidden subsurface defects through thermal differences also provides information about how these defects change over time.

In the field of Thermal Non-Destructive Testing and Evaluation (TNDT&E), active thermography gained popularity due to its fast, wide area monitoring and remote inspection capability to assess materials without compromising their future usability. Among the various active thermographic methods, pulse compression favourable frequency-modulated thermal wave imaging stands out for its enhanced detectability and depth resolution. In this study, experimental investigation has been carried out on a hardened steel sample used in ship building industry with a flat-bottom hole simulated defect using the Frequency Modulated Thermal Wave Imaging (FMTWI) technique. And the defect detection capabilities of FMTWI have been investigated from various statistical post processing approaches and compared by taking Signal to Noise Ration (SNR) as a figure of merit. Among various adopted statistical post-processing techniques, the pulse compression has been carried out using different methods: offset removal with polynomial curve fitting, and Principal Component Analysis (PCA) which is an unsupervised learning approach for data reduction and offset removal with median centering for data standardization. The performance of these techniques was assessed through experimental investigations on hardened steel specimen used in ship building to provide valuable insights into their effectiveness in defect detection capabilities.

In this study, the determination of static E50 and υ parameters of rock materials was investigated using P-S wave velocities and Shore hardness (SH), non-destructive measurement methods. We used multiple linear regression (MLR), multiple non-linear regression (MNLR) and artificial neural network (ANN) models to estimate and determine these parameters. When the models defined by MLR, MNLR, and ANN were compared to the R2 values, ANN models that estimate E50 and υ parameters of rock materials using non-destructive methods (Vp, Vs, Vp/Vs, d, and SH) could be determined with higher accuracy than MLR and MNLR models. The study’s originality is based on the fact that ores such as galena, chromite, and barite have been studied for the first time on rock mechanics, and in this respect, it offers an innovative perspective. In addition, the use of all non-destructive measurement methods, Vp, Vs, and Shore hardness tests, also increases the originality of the study.

China is a large agricultural country, and the crop economy has an important place in the national economy. The identification of crop diseases and pests, as well as the non-destructive classification of crops, has always been a challenge in agricultural development, hindering the rapid growth of the agricultural economy. Hyperspectral imaging technology combines imaging and spectral techniques, using hyperspectral cameras to acquire raw image data of crops. After correcting and preprocessing the raw image data to obtain the required spectral features, it becomes possible to achieve rapid non-destructive detection of crop diseases and pests, as well as non-destructive classification and identification of agricultural products. This paper first provides an overview of the current applications of hyperspectral imaging tech-nology in crops both domestically and internationally. It then summarizes the methods of hyper-spectral data acquisition and application scenarios. Subsequently, it organizes the processing of hyperspectral data for crop disease and pest detection and classification, deriving relevant pre-processing and analysis methods for hyperspectral data. Finally, it conducts a detailed analysis of classic cases using hyperspectral imaging technology for detecting crop diseases and pests and non-destructive classification, while also analyzing and summarizing the future development trends of hyperspectral imaging technology in agricultural production. The non-destructive rapid detection and classification technology of hyperspectral imaging can effectively select qualified crops and classify crops of different qualities, ensuring the quality of ag-ricultural products. In conclusion, hyperspectral imaging technology can effectively serve the ag-ricultural economy, making agricultural production more intelligent and holding significant im-portance for the development of agriculture in China.

Meat serves as a vital component of the human diet, offering a rich source of protein and essential trace elements. China stands as both a significant producer and consumer of meat on a global scale, leading the world in terms of total meat production and consumption. As the standard of living within the country continues to rise, there is a growing emphasis on the nutritional value and safety of meat consumption. The tenderness of meat is a critical factor influencing its overall quality. Traditionally, tenderness has been assessed through shear force testing, a method that is inherently destructive, inefficient, and results in considerable sample wastage. In light of these drawbacks, non-destructive testing techniques have emerged as a preferred alternative, promising greater accuracy, efficiency, and convenience without compromising the integrity of the samples. This paper delves into the application of five advanced non-destructive testing technologies in the realm of meat tenderness assessment. These include near-infrared spectroscopy, hyperspectral imaging, Raman spectroscopy, airflow optical fusion detection, and nuclear magnetic resonance detection. Each technology is scrutinized for its respective strengths and limitations, providing a comprehensive overview of their current utility and potential for future development. Moreover, the integration of these techniques with the latest advancements in artificial intelligence (AI) technology is explored. The fusion of AI with non-destructive testing offers a promising avenue for the development of more sophisticated, rapid, and intelligent systems for meat tenderness evaluation. This integration is anticipated to significantly enhance the efficiency and accuracy of quality assessment in the meat industry, ensuring a higher standard of safety and nutritional value for consumers. The paper concludes with a set of technical recommendations aimed at guiding the future direction of non-destructive, AI-enhanced meat tenderness detection, thereby contributing to the ongoing improvement of the meat industry in China and beyond.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

This work presents the study of a reproducible acoustic emission method based on the launching of a metallic sphere and low-cost piezoelectric diaphragm. For this purpose, tests were first conducted on a carbon fiber-reinforced polymer structure, and then on an aluminum structure for comparative analysis. The Pencil Lead Break (PLB) tests were also conducted for comparisons with the proposed method. Different launching heights and elastic deformations of the structures were investigated. The results show higher repeatability for the sphere impact method, as the PLB is more affected by human inaccuracy, and it was also effective in damage detection.

Biological nitrogen fixation (BNF) by symbiotic bacteria plays a vital role in sustainable agriculture. However, current quantification methods are often expensive and impractical. This study explores the potential of Raman spectroscopy, a non-invasive technique, for rapid assessment of BNF activity in soybeans. Raman spectra were obtained from soybean plants grown with and without rhizobia bacteria to identify spectral signatures associated with BNF. δN15 isotope ratio mass spectrometry (IRMS) was used to determine actual BNF percentages. Partial least squares regression (PLSR) was employed to develop a model for BNF quantification based on Raman spectra. The model explained 80% of the variation in BNF activity. To enhance the model's specificity for BNF detection regardless of nitrogen availability, a subsequent elastic net (Enet) regularization strategy was implemented. This approach provided insights into key wavenumbers and biochemicals associated with BNF in soybeans.

The moisture content of maize seed is an important indicator for evaluating seed quality and a fundamental item in grain testing. The experiment used direct drying method to measure the moisture content of 80 different varieties of maize samples, and captured their images using a hyperspectral imaging (HSI) system in the spectral range of 1100~2498nm. By comparing seven spectral preprocessing methods, the PLSR model established after Normalize pretreatment had the best effect. The characteristic wavelengths were selected by Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS) and Uninformative Variable Elimination (UVE). Twelve prediction models were established for full band spectra and characteristic wavelengths based on PLSR, PCR and SVM. By comparing the performance of the prediction models, it was found the Normalize-SPA-PLSR algorithm was optimized. The values of RC2 and RP2 in the model were higher, which were 0.9936 and 0.9933, respectively, while the values of RMSEP and RMSECV were lower, which were 0.0357 and 0.0380, respectively. The Normalize-SPA-PLSR model was used as a visual prediction model for moisture content of maize seed, the 20 maize varieties in the prediction set were visualized to obtain visualized color images of moisture content. The color differences between different moisture content images were significant. The result indicated that hyperspectral imaging could accurately, rapidly, and non-destructive predict moisture content of maize seed, which provided technical support for moisture content detection in the process of maize harvest, storage and processing.

In this paper, a non-destructive test to diagnose wear of blade´s compressor of a gas turbine is reported. Gas turbine was operating in Campeche City, Mexico, in a very aggressive environment, where the entry of solid particles is unavoidable. The objective was to reduce cost of maintenance in this equipment. Analysis on a blade of gas turbine was performed, which was in operation on an offshore platform. Compressor blade was exposed to a severe damage by the impact of particles and environmental pollutants such as salts, sands and sulphurs. In first stage of this analysis, a visual inspection with a borescope was performed, which has the ability to illuminate dark internal areas, with a bright light for visual examination and/or make a photographic reproduction in semi-annual maintenance cycles. Images analysis was used to determine the typical failure modes. In a second stage, a tribological characterization was carried out. Chemical composition of the material of blades was obtained. Scanning electron microscopy (SEM) was used to measure roughness and evaluate degradation of surfaces of blades after 30,000 service hours. The points, where peak stresses were calculated, correspond to those places in witch corrosion and some irregular scratches similar to plowing action, was observed. These are the points in which failures take place. Results showed wear modes were originated by a severe stinging action. Also, large craters, similar to those observed in solid particle erosion, were developed by at normal impact. In the same way it could be found some localized areas with a witch corrosion and irregular scratches similar to plowing action, was observed. These are the points in which failures take place.

Flare stacks are a key element in the safety of petrochemical and refinery industries; the correct operating conditions thereof must be ensured through a schedule for the periodic reviewing of all parts thereof. Advances in Non-Destructive Testing (NDT) in recent years and the application thereof to this field allow reliable, objective information to be obtained. This article describes and groups together the main applicable NDT techniques, analysing their advantages and disadvantages, updated with the new possibilities offered by unmanned aircraft or drones.

On-stream inspections are the most appropriate method for routine inspections during plant operation without going through production downtime. Ultrasonic inspection, one of the on-stream inspection methods, faces challenges when performed at high temperatures exceeding the recommended 52°C. This study aims to determine the ultrasonic velocity and attenuation with the known material grade, thickness, and temperatures by comparing theory calculation versus experiment with temperatures ranging between 30°C to 250°C on low carbon steel covering most petrochemical equipment material and working conditions. The theoretical analysis was to obtain Young's modulus, Poisson's ratio, and longitudinal velocity at different temperatures. The experiments validated the predicted results of ultrasonic change due to temperature increase and showed a maximum error of 3%. The experimental data of velocity and decibel change from the temperature range provide a reference for the future when dealing with unknown materials information on site that require a quick corrosion status determination.

The authors of the paper have made an attempt to detect the fibre content and fibre spacing in a steel fibre reinforced concrete (SFRC) industrial floor. Two non-destructive testing (NDT) methods: an electromagnetic induction technique and a radar-based technique were applied. The first method allowed to detect the spacing in subsequent layers located in the thickness of the slab. The result of the second method was a 3D visualization of the detected fibre in the volume of concrete slab. The conducted tests showed aptitude and limitations of the applied methods in estimating fibre volume and spacing. The two techniques also allowed to locate the areas with relatively low fibre concentration which are very likely to be characterized by low mechanical properties.

Ultrasonic nondestructive testing is widely used not only in the laboratory, but also in industry. The tests use various types of ultrasonic waves, diverse measurement techniques and different apparatus. One of the problems encountered is the high susceptibility of the surface wave to interference. Some of the interference is random in nature and can be minimized (e.g., contamination of the surface, resting a finger on the surface under study). Some of the interference is permanent in nature, such as variable surface roughness. The aim of the conducted research was to evaluate the influence of roughness on ultrasonic wave propagation. The study used samples with surface roughness Sa from 0.28 to 219µm, and ultrasonic surface wave probes with frequencies from 1.41 to 8.02 MHz. It was observed that roughness significantly affects the attenuation of the ultrasonic wave, and the differences in signal amplification reached more than 15dB. Similarly, the effect of the ultrasonic wave's transit time through surfaces of different roughness was noted. It was found that the difference in the ultrasonic wave transition time was more than 50 µs. The results of the study can be helpful, for ultrasonic testing of materials with different surface conditions.

Electromagnetic sensing has been used for diverse applications of non-destructive testing, including the surface inspection, measurement of properties, object characterization. However, the measurement accuracy could be significantly influenced by the lift-off between sensors and samples. To address the issue caused by lift-offs, various strategies have been proposed for the permeability measurement of ferromagnetic steels, which mainly involves different sensor designs and signal features (e.g., the zero-crossing feature). In this paper, a single high-frequency scenario for the permeability retrieval is introduced. By combining the signal of two sensing pairs, the retrieval of magnetic permeability is less affected by the lift-off of sensors. Unlike the previous strategy on reducing the lift-off effect (directly taking the phase term out of the integration) using the Dodd-Deeds analytical method, the proposed method is based on a high-frequency linear feature of the phase term. Therefore, this method has the merit of high accuracy and fast processing for the permeability retrieval (a simplified version of Dodd-Deeds analytical formulas after the integration). Experimental measurement has been carried out on the impedance measurement of designed sensors interrogating ferromagnetic dual-phase steels. For sensor lift-offs of up to 10 mm, the error of the permeability retrieval is controlled within 4 % under the optimal frequency.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

Eddy current sensors can be used to test the characteristics and measure the parameters of the conductive samples. As the main obstacle of the multi-frequency eddy current sensor, the lift-off distance affects the effectiveness and accuracy of the measurement. In this paper, a material-independent algorithm has been proposed for the restoration of the lift-off distance when using the multi-frequency eddy current sensor, which is based on the approximation under the thin-skin effect. Experiment testing on the performance of the proposed method is presented. Results show that from the dual-frequency inductance, the lift-off distance could be restored with a maximum error of 0.24 mm for the distance up to 12 mm. Besides, the derived lift-off distance is used for the inversion of the magnetic permeability. Based on a lift-off insensitive inductance (LII) feature, the magnetic permeability of steels can be inversed in an iterative manner, with an error of less than 0.6 % for the lift-off distance up to 12 mm.

An increasing need for better agricultural practices that are sustainable to provide increased yields of crops for the ever increasing food demand to be met for the growing world population is a current necessity. It is estimated by the UN that in 2050 the world’s populace may be as much as 9.8 billion global, yet, farmers still face several obstacles, which includes soil degradation, extreme temperatures, and drought which as increasingly becoming more severe with climate changes. Plant health monitoring is a method that will help to increase awareness about plant enhancing by studying how to increase crop yields while decreasing the environmental impacts. The use of low-cost, controlled environments, soil quality, water levels, and pathogenic and pests attacks can be regularly monitored. Currently, several diagnostic technologies and portable point-of-use methods and technologies are employed for detection of diseases, although, the current available lab-based methods used for plant’s diagnostics test are inadequate for plant point-of-use monitoring. The promotion of use of these point of use methods will enable pathogen detection, poor plant growth, unsuitable environmental conditions and nutrient use efficiency allowing for immediate and timely corrective actions to ensure minimal damage to the plants with maximal yield. Increase in the use of sustainable agri practices are required for ensuring higher yields with minimal inputs and that are non-destructive to the land and the use of improved methodologies and technologies will be useful tools for achieving sustainable agriculture.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

For the soil in different regions, the nutrient fertility contained in it is different, and the detection and zoning management of soil nutrients before tillage every year can improve grain yield. In this paper, an integrated learning strategy model based on black soil hyperspectral data is designed for rapid classification of organic matter content classification of black soil. Soil hyperspectral image dataset of Xiangyang Experimental Base was collected; by changing the internal structure of the stacking model, an LSVM-stacking model with (MLP, SVC, DTree, XGBl, kNN) five classifiers as the L1 layer was built, and the simulated annealing algorithm was used for hyperparameter optimization. Compared to other stacking models, the LSVM-stacking metrics are significantly improved. The accuracy rate of hyperparameter optimization is improved by 38.6515%, the accuracy rate of the independent test data set is 0.9488, and the comparison of individual learners can improve the recognition classification accuracy of label"1" to 1.0.

Developing efficient Artificial Intelligence (AI)-enabled system to substitute human role in non-destructive testing is an emerging topic of considerable interest. In this study, we propose a novel impact-echo analysis system using online machine learning, which aims at achieving near-human performance for assessment of concrete structures. Current computerized impact-echo systems commonly employ lab-scale data to validate the models. In practice, however, the echo patterns can be far more complicated due to varying geometric shapes and materials of structures. To deal with a large variety of unseen data, we propose a sequential treatment for echo characterization. More specifically, the proposed system can adaptively update itself to approaching human performance in impact-echo data interpretation. To this end, a two-stage framework has been introduced, including echo feature extraction and the model updating scheme. Various state-of-the-art online learning algorithms have been reviewed and evaluated for the task. To conduct experimental validation, we collected 10,940 echo instances from multiple inspection sites with each sample had been annotated by human experts with healthy/defective condition labels. The results demonstrated that the proposed scheme achieved favorable echo pattern classification accuracy with high efficiency and low computation load.

It is difficult to automatically recognize defects using digital image processing method in X-ray radiograph that tested from lap joint of unequal thickness plates. The continuous change of the wall thickness for the lap joint workpiece brings about the very different gray levels in X-ray background image. Besides, due to the shape and fixturing of the workpiece, the distribution of the weld seam in the radiograph is not vertical and results in an existence of a certain angle with the vertical direction. This makes it difficult for automatic defect detection and localization. In this paper, a method of X-ray image correction based on invariant moments is presented to solve the problem. In addition, an automatic defect detection method combined of image noise suppression, background removal, image segmentation and mathematical morphology is introduced. The results show that the proposed method can effectively recognize the gas pores in lap joint of unequal thickness and it is suitable for automatic detection.

In ancient buildings, timber members could need specific on-site interventions, including reinforcement or repair, sometimes inserting of reinforcing material into grooves routed in the original sound wood. Grooves number, positions and dimensions, and strengthening materials may differ, according to the desired increase of bending stiffness and strength. The Modulus-of-Elasticity (MOE) of each beam is of key importance, but the incisions can affect it, net of the reduction of the removed wood. In this study 12 old beams were accurately measured and their static and dynamic MOEs calculated before and after the grooves processing, to simulate the operations of typical reinforcing interventions. One groove was routed along the length of each beam and deepened progressively by three steps. Tests have showed how the MOE is affected by the groove depth, decreasing up to one third. The paper proves how the weakening effect of grooves on-site can be assessed with dynamic MOE and roughly predicted by means of visual survey. Grooves need for strengthening beams, must be carefully evaluated because of the variation of the actual mechanical properties, net to lost wood.

This paper presents the development of an underwater crack detection system for structural integrity assessment of submerged structures, like offshore oil and gas installations, underwater pipelines, underwater foundations for bridges, dams etc. Focus is on use of machine learning based approaches. First a detailed literature review of state of the current methods for underwater surface crack detection is presented highlighting challenges and opportunities. An overview of image augmentation approach for creation of underwater optical effects is also presented. Experimental results using standard network based machine learning approach, used for surface crack detection in onshore environment, is presented. Series of Test cases are presented where existing networks performance are improved using augmented images for underwater conditions. The experimental results demonstrate the effectiveness and accuracy of the proposed system in detecting cracks in underwater structures. The system has the potential to improve the safety and reliability of underwater structures and prevent catastrophic failures.

Alternating current field measurement (ACFM) testing is one of promising techniques in the field of non-destructive testing with advantages of the non-contact capability and the reduction of lift-off effects. In this paper, a novel crack detection approach is proposed to reduce the effect of the angled crack (cack orientation) by using rotated ACFM techniques. The sensor probe is composed of an excitation coil and two receiving coils. Two receiving coils are orthogonally placed in the centre of the excitation coil where the magnetic field is measured. It is found that the change of the x component and the peak value of the z component of the magnetic field when the sensor probe rotates around a crack follows a sine wave shape. A customised accelerated finite element method solver programmed in MATLAB is adopted to simulate the performance of the designed sensor probe which can significantly improve the computation efficiency due to the small crack perturbation. The experiments have also been carried out to validate the simulations. It is found that the ratio between the z and x components of the magnetic field remains stable under various rotation angles. It shows the potential to estimate the depth of the crack from the ratio detected by combining the magnetic fields from both receiving coils (i.e., the x and z components of the magnetic field) using the rotated ACFM technique.

In many advanced industrial applications, the thickness is a critical index, especially for metallic coatings. However, the variance of lift-off spacing between sensors and test pieces affects the measured voltage or impedance, which leads to unreliable results from the sensor. Massive research works have been proposed to address the lift-off issue, but few of them applies to the thickness measurement of planar metallic films with finite-size circular (disk) geometry. Previously, a peak-frequency feature from the swept-frequency inductance was used to compensate the measurement error caused by lift-offs, which was based on the slow-changing rate of impedance phase term in the Dodd-Deeds formulas. However, the phase of measured impedance is nearly invariant merely on a limited range of sample thicknesses and working frequencies. Besides, the frequency sweeping is time-consuming, where a recalibration is needed for different sensor setups applied to the online real-time measurement. In this paper, a single-frequency algorithm has been proposed, which is embedded in the measurement instrument for the online real-time retrieval of thickness. Owing to the single-frequency measurement strategy, the proposed method does not need to recalibrate for different sensor setups. The thickness retrieval is based on a triple-coil sensor (with one transmitter and two receivers). The thickness of metallic disk foils is retrieved from the measured electrical resistance of two transmitter-receiver sensing pairs. Experiments on materials of different electrical conductivities (from direct current), thicknesses and planar sizes (radii) have been carried out to verify the proposed method. The error for the thickness retrieval of conductive disk foils is controlled within 5 % for lift-offs up to 5 mm.

Electromagnetic sensors have been used for inspecting small surface defects of metals. Based on the eddy-current thin-skin regime, a revised algorithm is proposed for a triple-coil drive-pickup eddy-current sensor scanning over long surface crack slots (10 mm) with different rotary angles. The method is validated by the voltage measurement of the designed EC sensor scanning over a benchmark (ferromagnetic) steel with surface defects of different depths and rotary angles. With an additional sensing coil for the designed EC sensor, the defect angle (or orientation) can be measured without spatially and coaxially rotating the excitation coil. By referring to the voltage change (due to the defect) diagram (voltage sum versus voltage different) of two sensing pairs, the rotary angle of the surface crack is retrieved with a maximum residual deviation of 3.5 %.

Previously, various techniques have been proposed for reducing the lift-off effect on the thickness measurement of the non-magnetic films, including the peak-frequency feature and phase feature in the Dodd-Deed analytical formulation. To realise a real-time feedback response on the thickness monitoring, the phase term in the Dodd-Deeds formulation must be taken off the integration. Previous methods were based on the slow change rate of the phase term when compared to the rest of the term – the magnitude term. However, the change rate of the phase term is still considerable for a range of working frequencies. In this paper, a high-frequency feature has been found. That is, the ratio between the imaginary and real part of the phase term is proportional to the integral variable under high frequencies. Based on this proportion relationship, the phase term has been taken out; and a thickness algorithm has been proposed. By combing the measured impedance from the custom-built sensor (three coils), the thickness of the metallic film can be reconstructed. Experiments have been carried out for the verification of the proposed scenario. Results show that the thickness of the metal film can be reconstructed with a small error of less than 2 %, and immune to a reasonable range of lift-offs.

Peanuts, owing to their composition of complex carbohydrates, plant protein, unsaturated fatty acids, and essential minerals (magnesium, iron, zinc, and potassium), hold significant potential as a vital component of the human diet. Additionally, their low water requirements and nitrogen fixation capacity make them an appropriate choice for cultivation in adverse environmental conditions. The germination ability of seeds profoundly impacts the final yield of the crop, assessing seed viability of extreme importance. Conventional methods for assessing seed viability and germination are both time-consuming and costly. To address these challenges, this study investigated Visible-Near Infrared Spectroscopy (Vis/NIR) in the wavelength range of 500-1030 nm as a non-destructive and rapid method to determine the viability of two varieties of peanut seeds: North Carolina-2 (NC-2) and Spanish flower (Florispan). The study subjected the seeds to three levels of artificial aging through heat treatment, involving incubation in a controlled environment at a relative humidity of 85% and a temperature of 50°C over 24-hour intervals. The absorbance spectra noise was significantly mitigated and corrected to a large extent by combining the Savitzky-Golay (SG) and Multiplicative Scatter Correction (MSC) methods. To identify the optimal wavelengths for seed viability assessment, a range of meta-heuristic algorithms were employed, including world competitive contest (WCC), league championship algorithm (LCA), Genetics (GA), Particle Swarm Optimization (PSO), Ant Colony Optimization (ACO), imperialist competitive algorithm (ICA), learning automata (LA), heat transfer optimization (HTS), forest optimization (FOA), discrete symbiotic organisms search (DSOS), and cuckoo optimization (CUK). These algorithms offer powerful optimization capabilities for effectively extracting relevant wavelength information from spectral data. Results revealed that all the algorithms demonstrated remarkable accuracy in predicting the allometric coefficient of seeds, achieving correlation coefficients exceeding 0.985 and errors below 0.0036, respectively. In terms of execution time, the ICA (2.3635 seconds) and LCA (44.9389 seconds) algorithms exhibited the most and least efficient performance, respectively. Conversely, the FOA and the LCA algorithms excelled in identifying the least number of optimal wavelengths (10 wavelengths). Subsequently, the seeds were classified based on the wavelengths selected by the FOA (10 wavelengths) and (DSOS (16 wavelengths) methods, in conjunction with logistic regression (LR), decision tree (DT), Multilayer Perceptron (MP), support vector machine (SVM), k-nearest neighbor (K-NN), and NaiveBayes (NB) classifiers. The DSOS-DT and FOA-MP methods demonstrated the highest accuracy, yielding values of 0.993 and 0.983, respectively. Conversely, the DSOS-LR and DSOS-KNN methods obtained the lowest accuracy, with values of 0.958 and 0.961, respectively. Overall, our findings demonstrated that Vis/NIR spectroscopy, coupled with variable selection algorithms and learning methods, presents a suitable and non-destructive approach for detecting seed viability.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

The purpose of this work was to achieve non-destructive detection of the internal defects of in-shell walnuts using X-ray radiography technology based on improved Faster R-CNN network model. First, the FPN structure was added to the feature extraction layer to extract richer image information. Then ROI Align was used to instead of ROI Pooling for eliminating the localization bias problem caused by quantization operation. Finally, the Softer-NMS module was introduced to the final regression layer with the predicted bounding box for improving the localization accuracy of the candidate boxes. The results indicated that the internal defects in intact walnuts with shells could be identified effectively using the proposed improved network model in this study. Specifically, the discrimination accuracy of the in-shell sound, shriveled and empty-shell walnuts were 96.14%, 91.72% and 94.80% respectively, and the highest overall accuracy can reach 94.22 %. Contrasted with original Faster R-CNN network model, the mAP and F1-value of the improved Faster R-CNN model increased by 5.86% and 5.65%, respectively. Consequently, the proposed method can be applied for the in-shell walnuts with shriveled and empty-shell defects.

In an industrial environment, the quality assurance of weld seams requires extensive efforts. The most commonly used methods for that are expensive and time-consuming destructive tests, since quality assurance procedures are difficult to integrate into production processes. Beyond that, available test methods allow only the assessment of a very limited set of characteristics. They are either suitable for determining selected geometric features or for locating and evaluating internal seam defects. The presented work describes an evaluation methodology based on microfocus X-ray computed tomography scans (µCT scans) which enable the 3D characterization of weld seams, including internal defects such as cracks and pores. A 3D representation of the weld contour, i.e., the complete geometry of the joint area in the component with all quality-relevant geometric criteria, is an unprecedented novelty. Both the dimensions of the weld seam and internal defects can be revealed, quantified with a resolution down to a few micrometers and precisely assigned to the welded component. On the basis of the methodology developed within the framework of this study, the results of the scans performed on the alloy AA 2219 can be transferred to other aluminum alloys. In this way, the data evaluation framework can be used to obtain extensive reference data for the calibration and validation of inline process monitoring systems employing Deep Learning-based data processing.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

Industrial radiography is a pivotal non-destructive testing (NDT) method that ensures quality and safety in a wide range of industrial sectors. Conventional human-based approaches, however, are prone to challenges in defect detection accuracy and efficiency, primarily due to the high inspection demand from manufacturing industries with high production throughput. To solve this challenge, numerous computer-based alternatives have been developed, including Auto-mated Defect Recognition (ADR) using deep learning algorithms. At the core of training, these algorithms demand large volumes of data that should be representative of real-world cases. However, the availability of digital X-ray radiography data for open research is limited by non-disclosure contractual terms in the industry. This study presents a pipeline that is capable of modeling synthetic images based on statistical information acquired from X-ray intensity distribution from real digital X-ray radiography images. Through meticulous analysis of the intensity distribution in digital X-ray images, the unique statistical patterns associated with the exposure conditions used during image acquisition, type of component, thickness variations, beam divergence, anode heel effect, etc., are extracted. The realized synthetic images were utilized to train deep learning models, yielding an impressive model performance with mean intersection over union (IoU) of 0.93, and mean dice coefficient of 0.96, on real unseen digital X-ray radiography images. This methodology is scalable and adaptable, making it suitable for diverse industrial applications.

This research is aimed to develop the method for damage degree evaluation in metals and alloys during their deformation and destruction based on acoustic emission (AE) technique. Experimental studies were carried out on tensile specimens of high-strength steel with simultaneous registration of AE signals in tested material. It was shown that the time-dependent AE primary parameters, such as the AE signal maximum amplitudes and AE activity, do not have a clear relationship with the material damage degree. This fact makes it difficult to use standard methods for assessing the damage degree of acoustic signal sources, including defects. It was proposed to use the Kolmogorov-Smirnov criterion to differ the processes of metal plastic deformation and crack propagation during the rupture. The possibility of estimating the material damage degree by high-energy AE hits share was shown. Besides, a particular expression was obtained for evaluating the damage degree for the material under study.

In response to the growing inspection demand exerted by process automation in component manufacturing, Non-destructive testing (NDT) continues to explore automated approaches that utilize deep learning algorithms for defect identification, including within digital X-ray radiography images. This necessitates a thorough understanding of the implication of image quality parameters on the performance of these deep learning models. This study investigates the influence of two image quality parameters, namely Signal-to-Noise Ratio (SNR) and Contrast-to-Noise Ratio (CNR), on the performance of U-net deep learning segmentation model. Input images were acquired with varying combinations of exposure factors such as kilovoltage, milli-ampere, and exposure time, which altered the resultant quality. The data was sorted into 5 different datasets according to their measured SNR and CNR values. The deep learning model was trained 5 distinct times, utilizing a unique dataset for each training session. Training the model with high CNR values yielded an intersection over Union (IoU) metric of 0.9594 on test data of the same category but drops to 0.5875 when tested on lower CNR test data. The result in this study emphasizes the importance of achieving a balance in training dataset according to the investigated quality parameters, to enhance the performance of deep learning segmentation models in NDT radiography applications.

Early diagnosis and treatment have always been highly desired in the fight against cancer, and detection of circulating tumor DNA (ctDNA) has recently been touted as highly promising for early cancer screening. Consequently, the detection of ctDNA in liquid biopsy gains much attention in the field of tumor diagnosis and treatment, which has also attracted research interest from the industry. However, traditional gene detection technology is difficult to achieve low cost, real-time and portable measurement of ctDNA. Electroanalytical biosensors have many unique advantages such as high sensitivity, high specificity, low cost and good portability. Therefore, this review aims to discuss the latest development of biosensors for minimal-invasive, rapid, and real-time ctDNA detection. Various ctDNA sensors are reviewed with respect to their choices of receptor probes, detection strategies and figures of merit. Aiming at the portable, real-time and non-destructive characteristics of biosensors, we analyze their development in the Internet of Things, point-of-care testing, big data and big health.

Electromagnetic eddy current sensors are commonly used to identify and quantify the surface notches of metals. However, the unintentional tilt of eddy current sensors affects results of size profiling, particularly for the depth profiling. In this paper, based on the eddy current thin-skin regime, a revised algorithm has been proposed for the analytical voltage or impedance of a tilted driver–pickup eddy current sensor scanning across a long ideal notch. Considering the resolution of the measurement, the bespoke driver–pickup, also termed as transmitter-receiver (T-R) sensor is designed with a small mean radius of 1 mm. Besides, the T-R sensor is connected to the electromagnetic instrument and controlled by a scanning stage with high spatial travel resolution , with a limit of 0.2 μm and selected as 0.25 mm. Experiments have been out on the voltage imaging of an aluminium sheet with 7 machined long notches of different depths using T-R sensor under different tilt angles. By fitting the measured voltage (both real and imaginary part) with proposed analytical algorithms, the depth profiling of notches is less affected by the tilt angle of sensors. From the results, the depth of notches can be retrieved within a deviation of 10 % for tilt angles up to 60 degrees.

Defect detection in ferromagnetic substrates is often hampered by non-magnetic coating thickness variation when using conventional eddy current testing technique. The lift-off distance between the sample and the sensor is one of the main obstacles for the thickness measurement of non-magnetic coatings on ferromagnetic substrates when using the eddy current testing technique. Based on the eddy current thin-skin effect and the lift-off insensitive inductance (LII), a simplified iterative algorithm is proposed for reducing the lift-off variation effect using a multi-frequency sensor. Compared to the previous techniques on compensating the lift-off error (e.g., the lift-off point of intersection) while retrieving the thickness, the simplified inductance algorithms avoid the computation burden of integration, which are used as embedded algorithms for the online retrieval of lift-offs via each frequency channel. The LII is determined by the dimension and geometry of the sensor, thus eliminating the need for empirical calibration. The method is validated by means of experimental measurements of the inductance of coatings with different materials and thicknesses on ferrous substrates (dual-phase alloy). The error of the calculated coating thickness has been controlled to within 3 % for an extended lift-off range of up to 10 mm.

Eddy current based approaches have been investigated for a wide range of inspection applications. Dodd-Deeds model and the truncated region eigenfunction expansion (TREE) method are widely applied in various occasions, mostly for the cases that the sample is relatively larger than the radius of the sensor coil. The TREE method converts the integral expressions to the summation of many terms in the truncated region. In a recent work, the impedance of the co-axial air-cored sensor due to a plate of finite radius was calculated by the modified Dodd-Deeds analytical approach proposed by authors. In this paper, combining the modified analytical solution and the TREE method, a new finite region eigenfunction expansion (FREE) method is proposed. This method involves modifying its initial summation point from the first zero of the Bessel function to a value related to the radius of the plate, therefore makes it suitable for plate with finite dimensions. Experiments and simulations have been carried out and compared for the verification of the proposed method. Further, the planar size measurements of the metallic circular plate can be achieved by utilising the measured peak frequency feature.

Hyper spectral imaging (HSI) is a technique that is used to obtain the spectrum for each pixel in the image. It helps in finding objects and identifying materials etc. Such an identification is very difficult using other imaging techniques. It allows the researchers to investigate the documents without any physical contact. Nowadays detection of unequal Ink mismatch based on HSI has shown vast improvement in distinguishing the inks. Detection of unequal Ink mismatch is an unbalanced clustering problem. This paper used K-means Clustering for ink mismatch detection. K-means Clustering find same subgroups in the data based on Euclidean distance. This paper demonstrates performance in unequal Ink mismatch based on HSI.

The objective of the prototype is to eliminate the polluting contamination of water sources, due to the leak of industrial waste without any kind of treatment, mainly generated by the industries and home sector. In this project, a prototype of water purification by plasma technology has been designed. The prototype will convert contaminated water into the plasma stream and eliminate the pathogens from the water by exposing it to ultraviolet radiation and plasma sterilisation. The polluted water will be accelerated at high speed using a water pump in order to convert it into a liquid-gas mixture for ease plasma generation. This process will be achieved when the electric supply from a source of alternating current (AC) is applied to the water by means of high voltage electrodes. After which, the mixture slows down to return into liquid form and the clean water is obtained. The whole process takes place without significantly raising the temperature also knows as non-thermal plasma. The device also has an automatic flow and pressure control system. Finally, a short feasibility study has been conducted on the water samples collected and report obtained from Chennai Metropolitan Water Supply and Sewage boards are reported. It has been concluded that this new plasma-based water treatment system will be more efficient and cheaper than the current wastewater treatment techniques and can be used in the future as the replacement of current secondary and tertiary treatments of industrial wastewater.

This review paper aims to understand the current processing plant maintenance systems and further identify on-stream phased array corrosion mapping (PACM) to reduce turnaround maintenance (TAM) activity during plant operations. Reducing the TAM duration and extending the TAM interval are common goals of most researchers. Thus, a detailed review was performed to understand the maintenance systems and the problems faced. Furthermore, a review of the current PACM application and the possibility of applying it during on-stream inspection was also per-formed. PACM has better detectability for localized corrosion, and the results can be obtained for a range of thicknesses, which is the main advantage of this method. The challenge is to apply it to a surface with high temperatures, owing to the greater probe contact and the limitation of ultrasonic properties. This literature review provides a more precise direction for future research to evaluate PACM on piping that can be utilized in inspection during plant operation at elevated temperatures. Detecting and monitoring corrosion growth without shutdown.

Subsurface drainage systems remove excess water from the soil profile thereby improving crop yields in poorly drained farmland. Knowledge of the position of the buried drain lines is important: 1) to improve understanding of leaching and offsite release of nutrients and pesticides, and 2) for the installation of a new set of drain lines between the old ones for enhanced soil water removal efficiency. Traditional methods of drainage mapping involve the use of tile probes and trenching equipment. While these can be effective, they are also time-consuming, labor-intensive, and invasive, thereby entailing an inherent risk of damaging the drainpipes. Non-invasive geophysical soil sensors provide a potential alternative solution. Previous research has focused on the use of time-domain ground penetrating radar (GPR), with variable success depending on local soil and hydrological conditions and the central frequency of the specific equipment employed. The objectives of this study were 1) to test the use of a stepped-frequency continuous wave (SFCW) 3D-GPR (GeoScope Mk IV 3D-Radar with DXG1820 antenna array) for subsurface drainage mapping, and 2) to evaluate the performance of a 3D-GPR with the use of a single-frequency multi-receiver electromagnetic induction (EMI) sensor (DUALEM) in-combination. The 3D-GPR system offers more flexibility for application to different (sub)surface conditions due to the coverage of wide frequency bandwidth. The EMI sensor simultaneously provides information about the apparent electrical conductivity (EC_a) for different soil volumes, corresponding to different depths. This sensor combination was evaluated on twelve different study sites with various soil types with textures ranging from sand to clay till. While the 3-D GPR showed a high success rate in finding the drainpipes at five sites (sandy, sandy loam, loamy sand, and organic topsoils), the results at the other seven sites were less successful due to limited penetration depth (PD) of the 3D-GPR signal. The results suggest that the electrical conductivity estimates produced by the inversion of EC_a data measured by the DUALEM sensor could be a useful proxy to explain the success achieved by the 3D-GPR in finding the drain lines. The high attenuation of electromagnetic waves in highly conductive media limiting the PD of the 3D-GPR can explain the findings obtained in this research.

In many industrial, automotive, and aerospace applications, electro-mechanical systems are subjected to random vibration excitations, and the most critical components are required to undergo qualification tests to verify their suitability. Measured field data are commonly considered as reference for the synthesis of random stationary signals used as shaker input excitations in laboratory tests. For the most popular procedures of random-control testing, the user sets the input profiles in terms of power spectral density (PSD) associated with randomized phases generated by the shaker controller to finally provide the physical motion. As a result, the overall probability distribution of the test signal tends toward Gaussian, whereas many real-life random excitations prove non-Gaussian due to distinctive bursts and peaks. The quantitative estimate of the number and amplitudes of peaks present in a certain signal is usually made through the statistical parameter known as kurtosis. The so-called kurtosis control methods presented in the literature are conceived to perform qualification tests with random and non-Gaussian vibration excitations. In this paper, two novel algorithms able to synthesize shaker input signals for random-control testing with prescribed PSD and kurtosis value are proposed, and the results of their application are comparatively discussed to assess their effectiveness and potentialities in different kinds of qualification testing, including accelerated fatigue-life tests.

Acoustic emission monitoring (AEM) has emerged as an effective technique for detecting wire-breaks resulting from, e.g., stress corrosion cracking, and its application on prestressed concrete bridges is increasing. The success of this monitoring measure depends crucially on a carefully designed sensor layout. For this the attenuation of elastic waves within the structure’s material is determined ideally in-situ through object-related measurements with a reproducible signal source, typically a rebound-hammer. This assumes that the attenuation coefficients derived from rebound-hammer tests are comparable to those from wire-breaks, thus allowing their results to be directly applied to wire-break detection without further adjustments. This study challenges this assumption by analysing attenuation behaviour through an extensive dataset. Employing time-domain and frequency analysis, the research generates attenuation profiles from laboratory experiments and in-situ measurements across various girders and bridge structures, extracting the slope and standard deviation of the residuals. While generally validating this approach, the findings highlight differences in attenuation behaviour from among wire-break signals and rebound-hammer impulses, whereby the latter potentially underestimates the relevant attenuation of wire-breaks by approximately 20 %. Consequently, a transfer factor is proposed to adjust object-related measurement results for wire-break scenarios, including a variance of 1.0 dB/m to cover a 95 % confidence interval for sample scattering. Moreover, the anisotropic attenuation behaviour across different structures was studied, showing that transverse attenuation consistently exceeds the longitudinal, significantly influenced by structural features such as voids. In prefabricated concrete bridges with in-situ-cast concrete slabs, transverse signal transmission remains unhindered across multiple elements. Finally, the results provide a valuable reference for the design of sensor layouts in bridge monitoring, particularly benefiting scenarios where direct in-situ experiences are lacking.

Natural Fibre Composites (NFC) are eco-friendly, sustainable alternatives to synthetic polymers. However, some intrinsic natural fillers´ properties hinder their widespread implementation as re-inforcement in polymeric matrices and require further investigation. In the scope of this study, the thermal, rheologic, mechanical (tension and flexural modes), morphological properties, water ab-sorption and dimensional stability of the NF polypropylene (PP) based injection moulded compo-sites with the rice husk (rh) and olive pits (op) of 20 wt% and 30% wt%, were investigated. The results suggest that the higher content of the rice husk and olive pits led to a similar reduction of the Melt Flow Index (MFI), independent of the additive type compared to virgin polypropylene (PPv). The melting and crystallization temperatures of the PPrh and PPop composites did not change with statistical significance. The composites are stiffer than the PP matrix by up to 49% and possess higher mechanical strength in what concerns the tension mode at the expense of de-creased ductility. PPrh and PPop have superior flexural modulus in the bending mode, while the flexural strength improvement was accomplished for the PP30%rh. The dimensional stability of the composites was improved as the linear shrinkage in the flow direction was decreased by 49% for PPrh and 30% for PPop, positively correlating with an increase in the filler content and stiff-ness. PPop was less susceptible to water sorption than PPrh due to fibres' composition and larger surface-to-area volume ratios.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

This article describes the history of research and development of surface-penetrating radar, starting from the 60s in the USSR, and ending today in Russia and neighboring states formed after the collapse of the USSR. The outstanding role played in the initial period of this technology development by Prof. M.I. Finkelstein and his colleagues is highlighted. Their research had a significant impact on subsequent developments in modern Russia and the neighboring countries.

Soybean with insignificant differences in appearance have large differences in their internal physical and chemical components, therefore follow-up storage, transportation and processing require targeted differential treatment. A fast and effective machine learning method based on hyperspectral data of soybean for pattern recognition of categories is designed as a non-destructive testing method in this paper. A hyperspectral-image dataset with 2299 soybean seeds in 4 categories is collected; Ten features is selected by extreme gradient boosting algorithm from 203 hyperspectral bands in range 400 to 1000 nm; A Gaussian radial basis kernel function support vector machine with optimization by the Tree-structured Parzen Estimator algorithm is built as TPE-RBF-SVM model for pattern recognition of soybean categories. The metrics of TPE-RBF-SVM are significantly improved compared with other machine learning algorithms. The accuracy is 0.9165 in the independent test dataset which is 9.786% higher for vanilla RBF-SVM model and 10.02% higher than the extreme gradient boosting model.

In this paper we report the possibility of using the X-ray powder diffraction (XRPD) technique to detect the gamma-hydroxybutyric acid (GHB) as its sodium salt in different beverages but because it is not possible to freely buy them, beta-hydroxybutyric acid (BHB) and its sodium salt (NaBHB) were used as a model to fine tune an X-ray diffraction method for the qualitative analysis of the sodium salt of GHB. The method requires a small quantity of beverage, and an easy sample preparation, that consists only in the NaOH addition to the drink and a subsequent drying step. The dry residue obtained can be easily analyzed with XRPD using a single crystal X-ray diffractometer to exploit its high sensitivity that allows very fast patterns collection. Several beverages with different NaBHB:NaOH molar ratios were tested and the results show that NaBHB is detected in all drinks analyzed when NaBHB:NaOH molar ratio is 1:50 using characteristic peak at very low 2θ values that permits to detect its presence also in complex beverage matrices. Moreover, depending on the NaOH amount added, shifting and/or splitting of the characteristic peak of the NaBHB salt was observed, and the origin of this behavior was investigated.

The preservation of the authenticity of a building artefact is a responsible practice. On the other side, the need to save the building artefact from the natural and anthropic degradation, to ensure the structural reliability to the different actions, to define an efficient maintenance program are big challenges, that involves the cooperation of several professionals, responsible use of innovative techniques and materials that are nowadays available. This paper focuses on a specific design approach for the rehabilitation works of ancient constructions in archaeological sites. The proposed conceptual design approach implies different steps that allow the optimization of the design at an increasing level of knowledge on the existing structures and their materials. The design procedure on historical constructions generally includes the following steps: the collection of data, the structural identification, hazard, and vulnerability analysis, damage and risk analysis, a cost-benefit analysis, so only at the end of the process, the final design is achieved. In the archaeological area, some important design aspects cannot be defined before the execution work phase, since some elements could be revealed and identified during work execution, as a consequence, the final design has been often optimized after all this information has been acquired. A studied case in the archaeological site of Pompeii is herein presented to prove the efficiency of the proposed approach.

Patient-derived tumor organoids (PDTOs) are a novel preclinical model of non-small cell lung cancer (NSCLC) for studying tumor biology and precision medicine, which recapitulates tumor morphology and gene expression profile. However, some issues such as low establishment rates, long-term production, and the loss of the immune microenvironment have hindered their widespread practical use. In this study, we investigated the efficacy of a recently introduced free-floating organoid production method to address these issues. The free-floating approach provided PDTO establishment success rate of over 90 % resulting in organoid formation within a short period of one week. These organoids retained the elements of the parental tumor morphology and contained stroma and immune cell populations, as confirmed by flow cytometry analysis. Importantly, we found that the cytokine and growth factor expression profiles of the free-floating organoids correlated with those of the original tumors in 58 % of cases, indicating the preservation of tumor-associated signaling pathways. Obtained organoids exhibited different responses to anticancer chemotherapeutics that might be a result of variable expression of drug resistance-associated genes. Considering the high establishment rate and short time of free-floating organoid production, this technique provides a valuable tool for a more accurate evaluation of therapeutic strategies and cancer biology studies.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

Non-destructive testing has many advantages, such as the ability to obtain a large number of data without destroying existing structures. However, the reliability of the estimation accuracy and the limited range of applicable targets remains an issue. This study proposes to a novel pin penetration test method to determine the early age compressive strength of concrete before demolding. The timing of demolding and initial curing are determined according to the strength development of concrete. Therefore, it is important to determine the compressive strength at the early age before demolding at the actual construction site. The applicability of this strength estimation methodology at actual construction is investigated. Small test holes (12 mm in diameter) are prepared on the mold surface in real construction sites and mock-up specimens in advance. The pin is penetrated into these test holes to obtain the relationship between the compressive strength and the penetration depth. As a result, it is confirmed that the pin penetration test method is suitable to measure the early age compressive strength at actual construction site. This allows the benchmark values for compressive strength, necessary to avoid early frost damage, to be directly verified on the concrete structural members at the construction site. For instance, the compressive strengths of greater than 5 MPa and 10 MPa can be confirmed by the penetration depths benchmark values of 8.0 mm and 6.7mm or less, respectively.

The goal of this study was to evaluate the feasibility of methods based on the Worldwide Harmonized Light-Duty Vehicles Test Procedure Brake Cycle to measure brake wear particle emissions for currently used electrified vehicles. Our results indicated that reducing brake friction work reduced brake wear particle emissions. Commercially available, plug-in hybrid electric vehicles reduced emissions by 85% for PM₁₀, 78% for PM_2.5, and 87% for particle numbers (PNs) compared to vehicles with internal combustion engines. Brake friction work showed a linear relationship with PM₁₀ and PM_2.5. Nanoparticle PM emissions tended to increase slightly with regenerative braking, but did not contribute significantly to the overall PM percentage. the emission events of high number concentrations of nuclei mode particles (<20 nm in diameter) in electric vehicle brake assemblies designed for regenerative braking use under high-temperature, high-load braking conditions with full-friction brakes. The nuclei mode particles amplified the PN emissions and led to a high variability. In strict regulatory certification tests, where measurement reproducibility and stability are required, it is appropriate to measure PNs under brake conditions appropriate for the actual use of electric vehicles rather than under full-friction brake conditions or to remove particle measurements smaller than 20 nm.

A 17th century wall painting representing a Virgin between two Saints in a noble Italian renaissance palace, Palazzo Gallo in Bagnaia (Viterbo, Italy), was restored in 2021 in the context of a wider restoration campaign interesting the main room of the palace built by cardinal Sansoni Riario. Diagnostic analyses done with traditional characterization techniques (optical microscopy on micro-stratigraphic sections, X-ray fluorescence spectroscopy and Fourier transform infrared spectroscopy) provided the identification of both original painting and restoration materials, while imaging investigations as ultraviolet fluorescence photography, false color images and multispectral mapping provided by hypercolorimetric multispectral imaging (HMI) technique enabled the evaluation of the state of conservation, locating restoration interventions and supporting the monitoring of the cleaning procedure. An altered protective Paraloid-based coating dating from early 2000s had to be removed due to the unpleasant glossy finishing given to the painted surface, making the scene barely readable. To pursue a restoration protocol based on environmental sustainability and green chemistry, enzyme-based gels marketed by Nasier-Brenta© and CTS© companies were tested in different protocols for the cleaning of the mash covering the painting. Although some interesting results were observed, the enzymatic cleaning had a scarce effectiveness with timing beyond a reasonable interval. Traditional chemical solvents as Dowanol PM (methoxy-propanol) and benzyl alcohol were necessary to complete the cleaning of the painting surface.

Petrochemical plants use on-stream inspection more often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper's objective is to obtain documentary evidence on the accuracy of corrosion detection from 30°C to 250°C on A36 low-carbon steel by carrying out simulation experiments every 10°C steps. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant's end users to use the phased array mapping in the future during an inspection. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.

The epidemiological situation generated by COVID-19 has highlighted the importance of applying non-pharmacological measures. Among these, mass screening of the asymptomatic general population has been established as a priority strategy by carrying out diagnostic tests to limit the spread of the virus. In this article, we aim to evaluate the economic impact of mass COVID-19 screenings of an asymptomatic population through a Cost-Benefit Analysis based on the estimated total costs of mass screening versus health gains and associated health costs avoided. Excluding the value of monetized health, the Benefit-Cost ratio was estimated at approximately 0.45. However, if monetized health is included in the calculation, the ratio is close to 1.20. The monetization of health is the critical element that tips the scales in favour of the desirability of screening. Screenings with the highest return are those that maximize the percentage of positives detected.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

Biomimicry in additive manufacturing often refers to topology optimization and the use of lattice structures, due to the organic shape of the topology-optimized designs, and the lattices often looking similar to many light-weight structures found in nature such as trabecular bone, wood, sponges, coral, to name a few. Real biomimetic design however involves the use of design principles taken in some way from natural systems. In this work we use a methodology whereby high resolution 3D analysis of a natural material with desirable properties is “reverse-engineered” and the design tested for the purpose. This allows more accurate replication of the desired properties, and adaption of the design parameters to the material used for production (which usually differs from the biological material). One such example is the impact-protective natural design of the glyptodont body armour. In this paper we report on the production of body armour models in metal (Ti4Al4V) and analyze the resulting mechanical properties, assessing their potential for impact protective applications. This is the first biomimetic study using metal additive manufacturing to date.

Older adults in low-and middle-income countries experience a disproportionate burden of non-communicable diseases (NCDs). Unintentional injuries are among the major NCDs, and falls are the second leading cause of these injuries and deaths worldwide, including in Thailand. We aimed to culturally adapt the CDC’s Stopping Elderly Accidents, Deaths, and Injuries (STEADI) for Thai older adults and explore the feasibility, appropriateness, and acceptability of using STEADI in primary care via trained community health workers (CHWs) and care managers (CMs). STEADI takes a coordinated care approach that consists of three steps: screening, assessing, and intervening. In Step a, CHWs screened fall risk in 20 community-dwelling older adults using three key questions and found that all of them had fall risk, then CHWs screened with a Stay Independent questionnaire (range 0-14) and found that 100% have high fall risk (total scores 9.7± 2.4). In Step b, CMs assessed balance, vision, footwear, postural hypotension, medications, and CHWs assessed home hazards. They found that 50% had poor balance, 70% took 4+ medications,75% fell on the walkway, and 70% had no bathroom modifications. In Step c, individual participants received fall prevention interventions to mitigate their specific fall risk factors. CHWs and CMs indicated high acceptability (19.20±.1.31 of 20 total), appropriateness (18.80± 1.79 of 20 total), and feasibility (18.60±1.67 of 20 total) of the Thai-STEADI intervention. Our study showed that the community-based multifactorial Thai-STEADI delivered by CHWs and CMs is feasible and acceptable to prevent falls in older adults with limited access to health care.

In order to study the strength changes of concrete specimens under different loading conditions, based on the principle of minimum energy dissipation and from the Angle of concrete failure energy per unit area, the finite element numerical simulation software was applied to concrete specimens with different failure modes of tension, compression, bending and torsion, and the double-broken line damage constitutive model was adopted to simulate and analyze the failure forms of concrete specimens under different loading conditions. The failure area and failure energy of each specimen during loading were quantitatively calculated under each failure mode, and the relationship between the failure area and failure energy consumed under different failure modes was analyzed. The results show that under different failure modes, the failure area of concrete specimens is different, the energy consumed during failure is different, and the strength is different. However, in the process of failure, no matter how the failure mode changes, the failure energy W per unit area remains unchanged and is a constant, which is related to the physical properties of concrete itself.

Limiting harm to organisms via genetic sampling is an important consideration for rare species. Nondestructive sampling techniques have been developed to address this issue in freshwater mussels. Two methods, visceral swabbing and tissue biopsies, have proven to be effective for DNA sampling, though it is unclear as to which method is preferable for genotyping-by-sequencing (GBS). Tissue biopsies may cause undue stress and damage to organisms, while visceral swabbing potentially reduces the chance of such harm. Our study compared the efficacy of these two DNA sampling methods for generating GBS data for the Unionid freshwater mussel, Texas Pigtoe (Fusconaia askewi). Our results find both methods generate quality sequence data, though some considerations are in order. Tissue biopsies produced significantly higher DNA concentrations and larger numbers of reads when compared to swabs, though there was no significant association between starting DNA concentration and number of reads generated. Swabbing produced greater sequence depth (more reads per sequence) while tissue biopsies revealed greater coverage across the genome (at lower sequence depth). Patterns of genomic variation as characterized in principal component analyses were similar regardless of the sampling method, suggesting that the less invasive swabbing is a viable option for producing quality GBS data in these organisms.

To improve the measurement accuracy of wood density and study the linear correlation between the drill feed resistance and wood density, a new micro drill instrument that can can simultaneously measure the rotation resistance and feed resistance of the drill needle was designed. The test wood samples included hardwood, softwood and conifer. The absolute dry density of each wood sample was measured. The drill resistance data was tested by using self-developed micro drill instrument and Resistogaph 650-SC. 4 linear models between drill resistance and the absolute dry density of wood . The results showed that: the statistical indicators of each model of the self-made micro drill resistance in-strument were better than the corresponding indicators of Resistogaph 650-SC; the coefficient of determination of the linear regression model between the feed resistance of the self-made micro drill resistance instrument and the absolute dry density of wood was 0.946; the statistical indicators of model including rotation resistance and feed resistance, were better than those of the model only including rotation resistance. Therefor, the design proposed in the article is reasonable, and increasing the feed resistance can improve the measurement accuracy of the micro drill resistance instrument for measuring wood density.

The recent Google’s claim on breakthrough in quantum computing is a gong signal for further analysis of foundational roots of (possible) superiority of some quantum algorithms over the corresponding classical algorithms. This note is a step in this direction. We start with critical analysis of rather common reference to entanglement and quantum nonlocality as the basic sources of quantum superiority. We elevate the role of the Bohr’s principle of complementarity¹ (PCOM) by interpreting the Bell-experiments as statistical tests of this principle. (Our analysis also includes comparison of classical vs genuine quantum entanglements.) After a brief presentation of PCOM and endowing it with the information interpretation, we analyze its computational counterpart. The main implication of PCOM is that by using the quantum representation of probability, one need not compute the joint probability distribution (jpd) for observables involved in the process of computation. Jpd’s calculation is exponentially time consuming. Consequently, classical probabilistic algorithms involving calculation of jpd for n random variables can be over-performed by quantum algorithms (for big values of n). Quantum algorithms are based on quantum probability calculus. It is crucial that the latter modifies the classical formula of total probability (FTP). Probability inference based on the quantum version of FTP leads to constructive interference of probabilities increasing probabilities of some events. We also stress the role the basic feature of the genuine quantum superposition comparing with the classical wave superposition: generation of discrete events in measurements on superposition states. Finally, the problem of superiority of quantum computations is coupled with the quantum measurement problem and linearity of dynamics of the quantum state update.

Reporting on CSR activities has become the essence of reporting for modern business entities. In this regard, particular attention is paid to public interest companies. Therefore, the following paper aims to answer the question of whether there are differences in the linguistic structure of the studied CSR reports in three selected industry indices on the Warsaw Stock Exchange (WSE) in Poland, i.e. WIG-energy index, WIG-fuel index, WIG-mining index and their relationship with the performance of selected companies. The study was conducted on a purposely selected sample of companies between 2013 and 2018. A total of 138 CSR reports and 138 annual separate financial statements prepared in accordance with international balance sheet law were collected. The study was carried out based on a panel regression model. It was found that CSR reports contained similar average percentages of parts of speech such as nouns and adjectives. When linking the economic performance of companies, expressed with selected indices, to the information on the implementation of CSR concepts, it was revealed that the results are more likely to describe business performance when it is satisfactory.

We investigated the effect of lepidocrocite-type layered titanate, which we have been using to reduce brake-particle emissions in an environmentally friendly manner. The effect of titanate on reduction was evaluated using a small-scale inertia brake-material-friction-test dynamometer. We suggested that brake-particle emissions are related to the microphysical structure of the pad surface, such as the uniformity of friction film and secondary-plateau formation, and that friction materials containing titanate contribute significantly to the reduction in both particle mass (PM) and particle number (PN) emissions of brake particles for both non-asbestos organic (NAO) and low-steel (LS) pads. In our experiments, the PM- and PN-emission levels of brake particles from LS pads with the addition of titanate were comparable to those of NAO pads.

Brake wear particles, as the major component of non-exhaust particulate matter, are known to have different emissions, depending on the type of brake assembly and the specifications of the vehicle. In this study, brake wear and wear particle mass emissions were measured under realistic vehicle driving and full friction braking conditions using current commercial genuine brake assemblies. Although there were no significant differences in either PM₁₀ or PM_2.5 emissions between the different cooling air flow rates, brake wear decreased and ultrafine particle (PM_0.12) emissions increased with increasing cooling air flow rate. Particle mass measurements were collected on filter media, allowing chemical composition analysis to identify the source of brake wear particle mass emissions. The iron concentration in the brake wear particles indicated that the main contribution was derived from disc wear. Using a systematic approach that measured brake wear and wear particle emissions, this study was able to characterize correlations with elemental compositions in brake friction materials, adding to our understanding of the mechanical phenomena of brake wear and wear particle emissions.

In a single-center, retrospective study, 22 cases were enrolled and divided into two groups: those who underwent surgical wide excision (group A) and those who did not (group B). The study included 13 cases in group A and 9 cases in group B. In group A, 6 cases solely underwent surgical wide excision, while 7 cases received additional treatments like radiotherapy or chemotherapy. Conversely, in group B, 4 cases received chemotherapy, 4 cases received radiotherapy, and 1 case was managed through observation alone. The mean follow-up time was 60.15 months in group A and 43.44 months in group B, with no significant difference observed. In group A, 9 cases resulted in mortality, whereas 6 cases died within the follow-up period in group B. Lesion-free intervals post-operation were observed predominantly in group A, while 7 cases in group B never experienced freedom from skin lesions. Kaplan-Meier survival curve analysis demonstrated a significant difference between the survival curves of the two groups (P = 0.046). Among non-HIV Kaposi’s sarcoma patients, surgical wide excision appears to have a role in treatment. Patients in group A exhibit a more favorable outcome in the survival curve analysis.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

The utilisation of non-Saccharomyces yeasts in co-inoculation and non-thermal technologies for must sterilisation is becoming increasingly prevalent due to its notable utility and potential. This approach optimises the fermentation process, facilitates the production of wines with distinctive characteristics and enhances their stability. Two trials were conducted concurrently, designated as A and B. The same red must was utilized in both trials, with one undergoing UHPH treatment and the other serving as the control. The non-Saccharomyces yeasts were identical in both trials. In Trial A, different percentages of initial inoculum were employed with respect to the total volume of must to be fermented, with the objective of evaluating the influence and competitiveness between yeasts. Trial B was designed to investigate the impact of two nutrients that provide vitamins, energy and protection from oxidative stress on the development of these yeasts and their metabolic expression. A microbiological analysis was conducted, along with oenological parameter measurements, acidification assessments, volatile compound analyses, and spectrophotometric evaluations. It was observed in both trials that the prevalence of Lachancea thermotolerans (Lt) was longer than that of Metschnikowia pulcherrima (Mp), and that the use of quercetin + thiamine had a positive effect on yeast growth. Furthermore, the combination of Lt and Mp yeasts demonstrated remarkable synergy, resulting in the production of a substantial quantity of lactic acid (&gt;5 g/L). With regard to aroma compounds, the UHPH must exhibited a nearly twofold increase in ethyl lactate. Additionally, the TPI was observed to be 8-10% higher in wines derived from UHPH musts, indicating that this technology may potentially safeguard against oxidation.

For the treatment of cancer and other diseases, therapeutic targeting of non-coding RNAs (ncRNAs) such as microRNAs (miRNAs) and long non-coding RNAs (lncRNAs) is an attractive approach. RNA-based therapeutics have been extensively researched over the past decade, with antisense oligonucleotides and small interfering RNAs being the most commonly used. Some of these have even gained FDA approval. However, the results of trials have been mixed, with some studies reporting strong effects while others have shown limited effectiveness or toxicity. Alternative treatments, such as antimiRNAs, are currently in clinical trials. There is growing interest in the use of lncRNA-based therapies. This Perspective discusses the main challenges of ncRNA therapeutics, including specificity, delivery and tolerability. It also highlights emerging approaches that aim to improve their success.

Non-compliant (NC) structures are often encountered in building construction in developing countries. This is a condition whereby erected buildings do not follow regulatory standards, especially in the provision of reinforcements. Therefore, under an earthquake load, the structures do not have sufficient resistance against such load. The structural elements of the building, which often have NC conditions, are the beam-column joints because they do not contain adequate shear reinforcements due to installation difficulty. This study aims to determine the structural performance of the reinforced concrete (RC) frame, which has a reinforcement deficiency in the beam-column joints. Numerical simulation was conducted on the Kakaletsis structure model by modifying the reinforcement details at the joints to represent the NC conditions. The non-linear modeling and analysis of the structural model were carried out using ATENA software. The analysis showed that the reduction in shear reinforcements in the NC model joint caused a decrease in load-carrying capacity by about 26.04%. A shift was also observed in the collapse pattern, i.e., from the beam to the end of the column, causing global failure and reducing the undamaged but increasing more severely damaged condition. This showed that the NC structure, due to the non-conformance of reinforcement, significantly reduced the structure's performance.

An exhaustive list of thirteen instances of reports confirming experimentally the relativistic Doppler relation, are examined. For those involving longitudinal Doppler, the non-relativistic relation is seen to be confirmed, within the reported experimental accuracies, to the same degree as the standard relativistic relation. Higher values of the speed of the emitter would be required to examine further the claimed confirmations. For those reports involving saturation spectroscopy, there is much confusion over the appropriate Doppler relation to be used, together with some serious analytical flaws. For the two cases that involve transverse Doppler, there are seen to be either serious faults in the theoretical part, or intrusion from the first order effect. Therefore, the reported conclusions - that the results for the experiments confirm the relativistic SR relation - cannot be justified by any of the experimental works.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{F}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We show that the public, secret and channel keys become indistinguishable to the eavesdropper under matrix multiplication. Remarkably, for achieving a 512-bit security level, the public key is 1024 bits and the private key is 768 bits, making them the smallest keys among post-quantum key exchange algorithms. Also, we discuss how to achieve key authentication, interdomain certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

We introduce a novel key exchange protocol based on non-commutative matrix multiplication defined in $\mathbb{Z}_p^{n \times n}$. The security of our method does not rely on computational problems as integer factorization or discrete logarithm whose difficulty is conjectured. We claim that the unique eavesdropper's opportunity to get the secret/private key is by means of an exhaustive search which is equivalent to the unsorted database search problem. Furthermore, we show that the secret/private keys become indistinguishable to the eavesdropper. Remarkably, to achieve a 512-bit security level, the keys (public/private) are of the same size when matrix multiplication is done over a reduced 8-bit size modulo. Also, we discuss how to achieve key certification and Perfect Forward Secrecy (PFS). Therefore, Lizama's algorithm becomes a promising candidate to establish shared keys and secret communication between (IoT) devices in the quantum era.

This article develops duality principles and numerical results for a large class of non-convex variational models. The main results are based on fundamental tools of convex analysis, duality theory and calculus of variations. More specifically the approach is established for a class of non-convex functionals similar as those found in some models in phase transition. Finally, in some sections we present concerning numerical examples and the respective softwares.

Let $\mathbb{K}$ be a non-Archimedean (complete) valued field satisfying \begin{align*} \left|\sum_{j=1}^{n}\lambda_j^2\right|=\max_{1\leq j \leq n}|\lambda_j|^2, \quad \forall \lambda_j \in \mathbb{K}, 1\leq j \leq n, \forall n \in \mathbb{N}. \end{align*} For $d\in \mathbb{N}$, let $\mathbb{K}^d$ be the standard $d$-dimensional non-Archimedean Hilbert space. Let $m \in \mathbb{N}$ and $\text{Sym}^m(\mathbb{K}^d)$ be the non-Archimedean Hilbert space of symmetric m-tensors. We prove the following result. If $\{\tau_j\}_{j=1}^n$ is a collection in $\mathbb{K}^d$ satisfying $\langle \tau_j, \tau_j\rangle =1$ for all $1\leq j \leq n$ and the operator $\text{Sym}^m(\mathbb{K}^d)\ni x \mapsto \sum_{j=1}^n\langle x, \tau_j^{\otimes m}\rangle \tau_j^{\otimes m} \in \text{Sym}^m(\mathbb{K}^d)$ is diagonalizable, then \begin{align}\label{WELCHNONABSTRACT} \max_{1\leq j,k \leq n, j \neq k}\{|n|, |\langle \tau_j, \tau_k\rangle|^{2m} \}\geq \frac{|n|^2}{\left|{d+m-1 \choose m}\right| }. \end{align} We call Inequality (\ref{WELCHNONABSTRACT}) as the non-Archimedean version of Welch bounds obtained by Welch [\textit{IEEE Transactions on Information Theory, 1974}]. We formulate non-Archimedean Zauner conjecture.

Nonionizing millimeter-waves (MMW) interact with cells in a variety of ways. Here the inhibited cell division effect was investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm2 safety standards. Irradiation using a power density of about 1.0 mW/cm2 , SAR over 5-6 hours on 50 cells/μl samples of Saccharomyces cerevisiae model organism resulted in 62% growth rate reduction compared to the control (sham). The effect was specific for 85-105 GHz range, and was energy and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deleted cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause permanent genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm2) and compared to that of a compact waveguide (17.17 mW/cm2) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. We have shown that non-thermal MMW radiation has potential for future use in treatment of yeast related diseases and other targeted biomedical outcomes.

Nonionizing millimeter-waves (MMW) are reported to interact with cells in a variety of ways. Possible mechanisms of the inhibited cell division effect were investigated using 85-105 GHz MMW irradiation within the ICNIRP (International Commission on Non-Ionizing Radiation Protection) non-thermal 20 mW/cm² safety standards. ~1.0 mW/cm² exposure over 5-6 hours treatment on 50 cells/μl samples of Saccharomyces cerevisiae model organism, resulted in 62% growth rate reduction compared to control (sham). The effect was specific for 85-105 GHz range and energy dose and cell density dependent. Irradiation of wild type and Δrad52 (DNA damage repair gene) deletion cells presented no differences of colony growth profiles indicating non-thermal MMW treatment does not cause genetic alterations. Dose versus response relations studied using a standard horn antenna (~1.0 mW/cm²) and compared to that of a compact waveguide (17.17 mW/cm²) for increased power delivery resulted in complete termination of cell division via non-thermal processes supported by temperature rise measurements. Combinations of MMW mediated Structure Resonant Energy Transfer (SRET), membrane modulations eliciting signaling effects, and energetic resonance with biomolecules were indicated to be responsible for the observations reported. Our results provide novel mechanistic insights enabling innovative applications of nonionizing radiation procedures for eliciting targeted biomedical outcomes.

Non-isocyanate polyurethane synthesis by non-Sn catalysis is an essential challenge toward green polyurethane synthesis. Bismuth compounds are attractive candidates due to their low cost, low toxicity, and availability to urethane chemistry. We applied various Bi catalysts to the self-polycondensation of a bishydroxyurethane monomer and found BiCl3 to be an excellent catalyst through optimization. The catalytic activity and price of BiCl3 are comparable to those of Bu2SnO, while its toxicity is significantly low. BiCl3 is, therefore, a promising alternative to Sn-based catalysts in non-isocyanate polyurethane synthesis.

Wine is a processed beverage that offers high nutritional and health benefits. It is produced from grape must, which undergoes fermentation by yeasts (and sometimes lactic acid bacteria) to create a product that is highly appreciated by consumers worldwide. However, if only one type of yeast, specifically Saccharomyces cerevisiae, were used in the fermentation process, the resulting wine would lack aroma and flavor and may be rejected by consumers. To produce wine with a desirable taste and aroma, non-Saccharomyces yeasts are necessary. These yeasts contribute volatile aromatic compounds that significantly impact the wine’s final taste. They promote the release of primary aromatic compounds through a sequential hydrolysis mechanism involving several glycosidases unique to these yeasts. This review will discuss the unique characteristics of these yeasts (Schizosaccharomyces pombe, Pichia kluyveri, Torulaspora delbrueckii, Wickerhamomyces anomalus, Metschnikowia pulcherrima, Hanseniaspora vineae, Lachancea thermotolerans, Candida stellata, and others) and their impact on wine fermentations and co-fermentations. Their existence and the metabolites they produce enhance the complexity of wine flavor, resulting in a more enjoyable drinking experience.

Post-quantum public cryptosystems introduced so far do not define an scalable public key infrastructure for the quantum era. We demonstrate here a public certification system based in Lizama’s non-invertible Key Exchange Protocol which can be used to implement a public key infrastructure (PKI), secure, scalable, interoperable and efficient. We show functionality of certificates across different certification domains. Finally, we discuss that non-invertible certificates can exhibit Perfect Forward Secrecy (PFS).

It is well established in literature that the public debt and economic growth bear positive and non-linear relationship. However, in recent literature, evidence of no causal relationship is found when accounted for endogeneity in case of advanced economies (Panizza & Presbitero, 2014). Chudik, Mohaddes, Pesaran, & Raissi, (2017) analyse the data on forty countries and find no evidence of universally applicable threshold effect in the relationship between debt and growth. These advancements in the debt-growth literature provides the motivation to re-explore the relationship between public debt and economic growth under non-linearity and endogeneity in context of developing economies of South Asia including Pakistan, India, Bangladesh and Sri-Lanka for the period 1980-2014. There exists a significant, positive but nonlinear relationship between the public debt and economic growth for the selected set of developing countries when accounted for endogeneity and non-linearity. The negative association between the public debt and economic growth for SAARC region is found when the debt level is higher than 61% of GDP which is quite lower than developed economies (90% of GDP). Individual threshold levels for debt-to-GDP ratio divulge that Sri Lanka, Pakistan and India need to control their public borrowings as their current debt levels are higher and/or around the respective threshold levels.

We establish a new Gagliardo-Nirenberg inequality characterized by radial symmetry and involving potentials exhibiting pure power polynomial behaviour. As an application of our result, we investigate the existence of extremals for this inequality, which also correspond to stationary solutions for the nonlinear Schrödinger equation with inhomogeneous nonlinearity, competing with Hs-subcritical nonlinearities, either of local or non-local nature.

Non-alcoholic steatohepatitis (NASH), which is the most severe manifestation of non-alcoholic fatty liver disease (NAFLD), has been recognized as a major hepatocellular carcinoma (HCC) catalyst. However, the molecular mechanism of NAFLD-NASH-HCC sequence remains unclear and a specific and effective treatment for NASH has not yet been established. The progress in this field depends on the availability of reliable preclinical models which show the steady progress to NASH, liver cirrhosis, and HCC. However, most of NASH mouse models that have been described to date develop NASH generally for more than 24 weeks and there is an uncertainty of HCC development. To overcome such shortcomings of experimental NASH studies, we established a novel NASH-HCC mouse model with very high reproducibility, generality, and convenience. We treated male C57BL/6J mice with a newly developed choline-deficient and methionine-restricted high-fat diet (CDMRHFD) for 60 weeks. Treatment of CDMRHFD for 3 weeks revealed marked steatosis, lobular inflammation, and fibrosis, histologically diagnosed as NASH. Liver cirrhosis was observed in all mice with 36-week treatment. Liver nodule emerged at 12 weeks of the treatment, and diameter >2 mm liver tumors developed in all mice at 24 weeks of the treatment. In conclusion, our rapidly progressive and highly reproducible NASH-liver cirrhosis-HCC model is helpful for preclinical development and research on the pathogenesis of human NAFLD-NASH-HCC. Our mouse model would be useful for the development of novel chemistry for NASH-HCC-targeted therapies or HCC prevention strategies.

(1) Background: Although multiple studies have reported on the therapeutic effects of Atezo+Bev for the treatment of NASH-related liver cancer, few studies have focused on its effect on liver reserve. Here, we aimed to compare the changes in hepatic reserve during the Atezo+Bev treatment of NAFLD/NASH-related HCC and of non-NAFLD/non-NASH-related HCC. (2) Methods: We retrospectively compared the changes in ALBI score in 109 patients with NAFLD/NASH or non-NAFLD/non-NASH during 12 weeks of treatment with Atezo+Bev for advanced HCC between September 2019 and January 2022. PSM was performed, and the OS, PFS, and PPS of the two groups were compared. (3)Results: The ALBI after 12 weeks of Atezo+Bev treatment was significantly worse in the NAFLD/NASH group than in the non-NAFLD/non-NASH group. Analysis of the 24 propensity score-matched pairs of cases with NAFLD/NASH or non-NAFLD non-NASH yielded similar results. The prognoses of the two groups were similar with respect to OS and PFS, but the NAFLD/NASH group had a significantly shorter PPS. The 24 matched pairs had similar OS and PFS, but the PPS of the NAFLD/NASH group was shorter. (4)Conclusion: Atezo+Bev treatment may worsen hepatic reserve, and there-fore life expectancy, in patients with NAFLD/NASH-related liver cancer.

This article develops a duality principle and a related convex dual formulation suitable for a large class of models in physics and engineering. The results are based on standard tools of functional analysis, calculus of variations and duality theory. In particular, we develop applications to a model in non-linear elasticity.

The connection of two phenomena - non-conservative friction forces and dissipation-induced instability can lead to many interesting engineering problems. The paper studies general material-dependent damping influence on dynamical instability of disc brake systems leading to brake squeal. The effect of general damping is demonstrated on a minimal and complex model of a disc brake. A complex system including material-dependent damping is defined in the commercial finite element software. The finite element model validated by experimental data on the brake-disc test bench is used to compute the influence of a pad and a disc damping variations on system stability by complex eigenvalue analysis. Analyzes show a significant sensitivity of the experimentally verified unstable mode of the system to the ratio of the damping between the disc and the friction material components.